ZXSDR B8200 GU360 (V4.00.100) Indoor GSM&UMTS Dual Mode Baseband Unit Ground Parameter Reference

“ ”b 2 d 2 � � – – “ ” “ ” – – “ ” “ ” “ ” “ ” – – – – “ ” “ ” “ ” – – – “ ” – – “ ” – – – – – – – – – – – – – – – – – – – LEGAL INFORMATION Copyright © 2006 ZTE CORPORATION. The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations. All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE CORPORATION or of their respective owners. This document is provided “as is”, and all express, implied, or statutory warranties, representations or conditions are disclaimed, including without limitation any implied warranty of merchantability, fitness for a particular purpose, title or non-infringement. ZTE CORPORATION and its licensors shall not be liable for damages resulting from the use of or reliance on the information contained herein. ZTE CORPORATION or its licensors may have current or pending intellectual property rights or applications covering the subject matter of this document. Except as expressly provided in any written license between ZTE CORPORATION and its licensee, the user of this document shall not acquire any license to the subject matter herein. ZTE CORPORATION reserves the right to upgrade or make technical change to this product without further notice. Users may visit ZTE technical support website http://ensupport.zte.com.cn to inquire related information. The ultimate right to interpret this product resides in ZTE CORPORATION. Revision History Revision No. 1.0 Revision Date 20090105 Revision Reason First Edition (B8200 GU360 V4.00.100b2 + OMMB V4.00.100d2) Serial Number: 20085384 Contents Preface............................................................... i General Configuration Parameters ....................1 Base Station .................................................................. 1 BS Equipment Resource Management................................ 4 Rack ............................................................................. 6 Rack Topo...................................................................... 7 Antenna ........................................................................ 9 RF Connection...............................................................10 Tower Top Amplifier .......................................................11 Environment Supervision ................................................13 Clock Source PRI ...........................................................14 Serial Port Information ...................................................15 AISG Device .................................................................16 Dry Contact ..................................................................17 Transmission Configuration Parameters.......... 19 Physical Layer Management ............................................19 E1/T1 Link................................................................19 HDLC Link ................................................................20 Time Slot Interchange ................................................22 Global Port Layer Management ........................................23 Ethernet...................................................................23 QoS Bandwidth .........................................................25 PPP Link ...................................................................26 Global Port ...............................................................30 IP/Static Router Layer Management .................................31 IP Parameter.............................................................31 Static Router.............................................................33 Transmission Layer Management .....................................34 SCTP Association .......................................................34 SCTP Stream ............................................................37 OMC-B Link ..............................................................38 Clock Configuration........................................................39 IP Clock ...................................................................39 Figures ............................................................ 41 Tables ............................................................. 43 List of Glossary................................................ 45 Preface Purpose ZXWR OMM is the operation and maintenance module of ZTE WCDMA product series. Configuration management, fault management, topology management, performance management and security management can be performed via OMM. This manual is a parameter reference for BS ground resource management. What is in This Manual TABLE 1 CHAPTER SUMMARY Chapter Chapter 1 General Configuration Parameters Chapter 2 Transmission Configuration Parameters Summary Introduces general configuration parameters of ground resource management. Introduces transmission configuration parameters of ground resource management. Intended Audience � � Maintenance engineer NM engineer Confidential and Proprietary Information of ZTE CORPORATION i ii Confidential and Proprietary Information of ZTE CORPORATION .ZXSDR B8200 GU360 Ground Parameter Reference This page is intentionally blank. .............17 Base Station Interface The related interface is shown in the figure below............................ 7 Antenna ...................................................14 Serial Port Information ....................................10 Tower Top Amplifier ..........................................11 Environment Supervision .................................................16 Dry Contact ............ 4 Rack ..........................................................................13 Clock Source PRI ............15 AISG Device ................................................ Confidential and Proprietary Information of ZTE CORPORATION 1 ........................................ 9 RF Connection...... 1 BS Equipment Resource Management.........................................................................................................................................................................................................................................Chapter 1 General Configuration Parameters Table of Contents Base Station ...................................................................................... 6 Rack Topo............................................ ZXSDR B8200 GU360 Ground Parameter Reference 2 Confidential and Proprietary Information of ZTE CORPORATION . Description Value Range Remarks User Label Managed Element ID Managed Type Element Self-defined name ID of BS managed element.Chapter 1 General Configuration Parameters Parameter Parameter Parameter description is shown in the table below. 65535] {ZTE series BS type} - Managed Element IP Address Vendor Name User Defined State 40 characters at most - - Confidential and Proprietary Information of ZTE CORPORATION 3 . for OMM use BS Type IP address for BS operation and maintenance BS manufacturer Reserved field 40 characters at most [0. 180. 4 Confidential and Proprietary Information of ZTE CORPORATION .00000. 90.00000. Longitude of BS location Latitude of BS location Value Range 40 characters at most {Software Version} [-180. Testing} BS Equipment Resource Management Interface The related interface is shown in the figure below.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Location Software Version Longitude Latitude Description Description of BS installation location BS Software Version No.00000] [-90. Maintain Status Whether ME is in service state {Normal.00000] Remarks OMM does not report to upper-level NM system the alarm caused by BS testing status. 65535] Remarks Inter-Operability parameter. consistent with RNC configuration Base Station No Base Station Description Base Station Type BS Description BS Type 200 characters at most - Parameter value automatically set by the system Confidential and Proprietary Information of ZTE CORPORATION 5 . Description Self-defined name Value Range 40 characters at most [0.Chapter 1 General Configuration Parameters Parameter Parameter User Label Base Station ID Parameter description is shown in the table below. – Power Work Model Working mode of the two power supplies Network switch model when two FS boards are configured. Burthen Partake Model} {Full IP} {GSM. 6 Confidential and Proprietary Information of ZTE CORPORATION . Not Supported} If the parameter is configured as “supported”. Not Supported} Network Switch Model Transmission Type Radio Mode Support Summer Time – If the parameter is configured as “supported”. Rack Interface The related interface is shown in the figure below. The current version only supports “Master And Slave Model”. system will adjust the operation of BS board in order to save power. FE. 65535] Remarks – Clock Sync Period(Hours) Medium Type of IUB Line NTP Server IP Address Time Zone Support Power-off Control [0. T1. Burthen Partake Model} {Master And Slave Model. Transmission type at Iub/Abis interface Radio mode used by the dual-mode BS Whether summer time is supported {Master And Slave Model. GSM/WCDMA} {Supported.ZXSDR B8200 GU360 Ground Parameter Reference Parameter GSM No Description GSM No when GSM mode of the BS is supported SNTP clock synchronization period for the BS Transmission medium at Iub/Abis interface Time server IP address The time zone where OMC-B is located Whether power-off control is supported Value Range [0. Starting and ending summer time should be configured. Sat. WCDMA. GE} - – - Refer to software pull-down list {Supported. 48] - {E1. - Rack Type Rack Name Phone Number Rack type User-Defined rack name Phone number {Rack type} 200 characters at most - Rack Topo Interface The related interface is shown in the figure below. is 2~25. Value Range 40 characters at most Remarks - Rack No. RU/RRU rack No.Chapter 1 General Configuration Parameters Parameter Parameter User Label Parameter description is shown in the table below. Confidential and Proprietary Information of ZTE CORPORATION 7 . Description Self-defined name for the current MO (managed object). 25] Main rack No. is 1. Rack No. [1. {The rack that can be cascaded} Slot No. of upper-level board in the case of cascade networking Port ID of upper-level board in the case of cascade networking Value Range 40 characters at most {The rack that can be cascaded} Remarks Cascading interface A Shelf No.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter User Label Rack No. {The rack that can be cascaded} Port ID Depending on board type 8 Confidential and Proprietary Information of ZTE CORPORATION . Parameter description is shown in the table below. of upper-level board in the case of cascade networking Slot No. of upper-level NE in the case of cascade networking Shelf No. Description Self-Defined Name Rack No. {The rack that can be cascaded} Child Slot No. of lower-level board in the case of cascade networking Slot No. Parameter Parameter User Label Parameter description is shown in the table below.Chapter 1 General Configuration Parameters Parameter Child Rack No. of lower-level board in the case of cascade networking Port ID of lower-level board in the case of cascade networking RRU networking mode Value Range {The rack that can be cascaded} Remarks Cascading interface B Child Shelf No. of lower-level NE in the case of cascade networking Shelf No. Description Rack No. Description Self-defined name Value Range 40 characters at most Remarks - Confidential and Proprietary Information of ZTE CORPORATION 9 . {The rack that can be cascaded} Depending on the type of lower-level BS/RRU Depending on the networking mode supported by RRU/BBU - Child Port ID RRU Connection Mode Antenna Interface The related interface is shown in the figure below. - Antenna Type Antenna type ANT-Ordinary antenna.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Rack No. RET} Remarks - Slot No. 10 Confidential and Proprietary Information of ZTE CORPORATION . RET-Remote electrical tilt antenna RF Connection Interface The related interface is shown in the figure below. Description No. of the rack that can be configured with antenna Antenna ID Value Range {The rack that has been created and can be configured with antenna} Depending on the maximum number of antennas per rack {ANT. Parameter Parameter description is shown in the table below. of the rack where the RF unit used by the current RF connection is located ID of the RF unit (board) used by the current RF connection Port ID of the RF unit used by RF connection - board (rack. 254] {Uplink (Receive). slot) In/Out Port ID - - - In Port ID is configured for uplink. Confidential and Proprietary Information of ZTE CORPORATION 11 . Tower Top Amplifier Interface The related interface is shown in the figure below. shelf. Downlink (Transmit)} Remarks - RF Connection Type Depending on BS type and the corresponding board type - - Rack No.Chapter 1 General Configuration Parameters Parameter User Label RF Connection ID Transceiving Flag Description Self-Defind Name ID of RF connection Whether the RF connection is transmit connection or receive connection Type of RF connection Value Range 40 characters at most [0. No. Out Port ID is configured for downlink. 52] x (0. 170] x (0. ATMA./Antenna ID of the antenna that is connected with tower amplifier Type of tower top amplifier Uplink power gain Value Range 40 characters at most {ID of the created antenna} Rack No. ACOM} TMA[110. Description Self-defined name Rack No./ shelf No. 240] x (0. TMB30.1 dB) 12 Confidential and Proprietary Information of ZTE CORPORATION .ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter User Label Parameter description is shown in the table below. TMB40.25dB) ACOM[0. 130] x (0.1dB) TMB30/40 [120./Tower Top Amplifier ID Type Uplink Power Gain {TMA.1dB) ATMA[44./ shelf No. 14] x (0.5dB) Downlink Power Gain Downlink power gain TMB30/40 [70. 1 dB) [0. 80] x (0.Chapter 1 General Configuration Parameters Parameter Tower Top Amplifier Noise Coefficient Tower Top Amplifier Feeder Cable Loss Minimum Power Supply Current Work Current Alarm Upper Limit Work Current Alarm Lower Limit Description Noise coefficient Feeder loss Under-Current alarm threshold Upper limit of work current alarm Lower limit of work current alarm Value Range [10. 160] [70. 85] Environment Supervision Interface The related interface is shown in the figure below.1 dB) [0. Parameter Parameter description is shown in the table below. 70] [135. Confidential and Proprietary Information of ZTE CORPORATION 13 . 30] x (0. Shelf No. VSWR Alarm Threshold} Depending on environment supervision type Depending on environment supervision type Clock Source PRI Interface The related interface is shown in the figure below. Description Self-Defined name Value Range 40 characters at most Remarks - 14 Confidential and Proprietary Information of ZTE CORPORATION . where SA board is located Environment supervision type Alarm upper limit Alarm lower limit {External Temperature. Environment Monitoring Threshold Type Upper Limit Lower Limit Description Self-defined name Location of the SA board Value Range 40 characters at most Rack No. Parameter Parameter User Label Parameter description is shown in the table below./Shelf No.ZXSDR B8200 GU360 Ground Parameter Reference Parameter User Label Rack No. Slot No./Slot No. the higher the priority level becomes.Chapter 1 General Configuration Parameters Parameter External Clock Source ID Priority Description Type of external clock source Priority of clock source Value Range Depending on the clock source supported by BS Depending on the number of clock sources supported by BS Remarks - Parameter value and priority level are inversely correlated. Description Self-defined name Value Range 40 characters at most Remarks - Confidential and Proprietary Information of ZTE CORPORATION 15 . Parameter Parameter User Label Parameter description is shown in the table below. (The lower the value is.) Serial Port Information Interface The related interface is shown in the figure below. /Shelf No. Description Location of the board with the current serial port Serial port No. 115200} - Baud Rate Transmission baud rate at serial Port Consistent with serial port device configuration AISG Device Interface The related interface is shown in the figure below. 9600. 38400. 57600.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Rack No. Serial Port No. 16 Confidential and Proprietary Information of ZTE CORPORATION .) {4800. Value Range Depending on BS type Remarks - Depending on type of the board which supports serial port (The number of serial ports supported by different boards varies. Parameter Parameter description is shown in the table below./Slot No. 19200. /Shelf No. the parameter represents antenna ID. ACOM} - For remote electrical tilt antenna. it is ACOM channel ID. Slot No. for active combiner. ATMA. Depending on BS device type Dry Contact Interface The related interface is shown in the figure below.0} CCU Rack No. {RET. Only two AISG protocol versions exist currently. 2.Chapter 1 General Configuration Parameters Parameter User Label Device ID Description Self-Defined name Serial number of AISG device AISG device type The rack/ shelf where AISG device is located The slot where AISG device is located Value Range 40 characters at most 32 characters at most Remarks The first two characters represent manufacturer ID.1./CCU Slot No. it is the ID of tower amplifier. AISG protocol version No. for tower amplifier. - AISG Version No. Location of AISG CCU (control and clock unit) at BS device {1. Confidential and Proprietary Information of ZTE CORPORATION 17 . - Device Type Rack No./ CCU Shelf No. Master power supply fault. Storage battery alarm. Description Self-defined name Location of the board where dry contact signal is inputted Dry contact port ID Setting the status under which the alarm is activated Value Range 40 characters at most Remarks - Depending on BS type {Closed./Shelf No. Shelf Indoor Surge Protection Device alarm. closed circuit produces alarm and the parameter is configured as “Closed”. Immersion alarm. Turnoff Equipment of Indoor Surge Protection Device alarm. When the initial state of dry contact is closed circuit. open circuit produces alarm and the parameter is configured as “Open”. Alarm Mode Parameter description is shown in the table below./Slot No. Equipment of Indoor Surge Protection Device alarm. Alarm Content No.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter User Label Rack No. Smog alarm. Master power supply broken alarm. Alarm content produced after reception of dry contact signal {TMB downlink bypass alarm. Dry Contact No. Outdoor Surge Protection Device alarm} - 18 Confidential and Proprietary Information of ZTE CORPORATION . TMB uplink bypass alarm. Open} When the initial state of dry contact is open circuit. master power supply lack voltage alarm. Master power supply over voltage alarm. ....23 IP/Static Router Layer Management ..............39 Physical Layer Management E1/T1 Link Interface The related interface is shown in the figure below.............. Confidential and Proprietary Information of ZTE CORPORATION 19 ...........................................................................................................................Chapter 2 Transmission Configuration Parameters Table of Contents Physical Layer Management .......................19 Global Port Layer Management .........34 Clock Configuration......................................31 Transmission Layer Management ....... /E1/T1 Link ID Link Type {RNC.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter User Label Parameter description is shown in the table below. BSC./Slot No./Shelf No. 20 Confidential and Proprietary Information of ZTE CORPORATION . ALL} HDLC Link Interface The related interface is shown in the figure below. Description Self-defined name Location which the E1/T1 link is connected with (rack/ shelf/ slot/port) Far-End equipment which E1/T1 link is connected to Value Range 40 characters at most - Rack No. Chapter 2 Transmission Configuration Parameters Parameter Parameter User Label Parameter description is shown in the table below./Slot No/HDLC ID/Bearer Link Type HDLC Link ID Row No. 31] - Confidential and Proprietary Information of ZTE CORPORATION 21 . Description Self-Defined Name The type of link which bears HDLC and the link location HDLC link ID The E1/T1 time slot used by HDLC link Value Range 40 characters at most - Rack No./Timeslot Map [0./Shelf No. Parameter description is shown in the table below.ZXSDR B8200 GU360 Ground Parameter Reference Time Slot Interchange Interface The related interface is shown in the figure below./Slot No./Shelf No. Parameter Parameter User Label Rack No. Description Self-defined name Location of the interface board where time slot interchange is performed Value Range 40 characters at most Remarks - 22 Confidential and Proprietary Information of ZTE CORPORATION . Chapter 2 Transmission Configuration Parameters Parameter In E1/T1 Link ID Description ID of in E1/T1 link Value Range Depending on the number of E1/T1 lines on interface board Depending on the number of E1/T1 lines on interface board - Remarks - Out E1/T1 Link ID ID of out E1/T1 link - Row No./In Timeslot Map/Out Timeslot Map To select the time slot used in time slot interchange To configure time slot to be used as “in use” The number of in time slots and that of out time slots should be the same. Global Port Layer Management Ethernet Interface The related interface is shown in the figure below. Confidential and Proprietary Information of ZTE CORPORATION 23 . 100Mbps half-duplex. Description Self-defined name Location which the Ethernet link is connected with (rack/shelf/board slot/port) Ethernet working mode Value Range 40 characters at most Remarks - Working Mode {10Mbps half-duplex. 100000] Inter-Operability parameter. Self-Adaptive. 10Mbps full-duplex. 1000Mbps} {IPbone. 100Mbps full-duplex. BTS} [0.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter User Label Rack No. consistent with far-end equipment Link Object Bandwidth Ethernet link object Link bandwidth – - 24 Confidential and Proprietary Information of ZTE CORPORATION ./Port ID Parameter description is shown in the table below./Shelf No./Slot No. Confidential and Proprietary Information of ZTE CORPORATION 25 ./Shelf No. Description Self-Defined name Location which the Ethernet link is connected with (rack/shelf/board slot/port) Traffic quality priority Link bandwidth in the case of fixed priority Value Range 40 characters at most Remarks - Traffic Quality Priority Bandwidth of QoS [0./Port ID Parameter description is shown in the table below.Chapter 2 Transmission Configuration Parameters QoS Bandwidth Interface The related interface is shown in the figure below. 255] – – The total bandwidth for all priorities cannot exceed the configured Ethernet bandwidth. Parameter Parameter User Label Rack No./Slot No. ZXSDR B8200 GU360 Ground Parameter Reference PPP Link Interface The related interface is shown in the figure below. 26 Confidential and Proprietary Information of ZTE CORPORATION . Chapter 2 Transmission Configuration Parameters Confidential and Proprietary Information of ZTE CORPORATION 27 . Description Value Range Remarks Self-Defined name Location of the link which bears Pointto-Point Protocol (rack/shelf/board) The bottom-layer protocol used by PPP link 40 characters at most - - Link Type {HDLC} - 28 Confidential and Proprietary Information of ZTE CORPORATION ./Shelf No.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter [Basic Information] User Label Rack No. Parameter description is shown in the table below./Slot No. multiple HDLC links may be selected when bearer protocol is “ML-PPP”. ML-PPP} - Remarks – IP address is obtained automatically if parameter value is “0. Authentication Enabled} - Authentication User Name Authentication Password [IP Information] IP Compression Authentication user name during link establishment Authentication password during link establishment - - - Whether IP compression is supported Maximum interval packets between full headers Maximum interval period between full headers Maximum TCP compression ID Maximum NONTCP compression ID Maximum length of compressible header {Compression Disabled. One HDLC link can be selected when bearer protocol is “PPP”. Service quality protocol The HDLC link which bears PPP protocol {LQR. 65535] - Maximum Period Between Full Headers Maximum Time Between Full Headers Maximum TCP Compression ID Maximum NONTCP Compression ID Maximum Length of Header - [1. [Authentication Information] Authentication Whether to perform authentication {Authentication disabled. 255] - [3. 65535] [60.0”. - Quality Protocol HDLC No.Chapter 2 Transmission Configuration Parameters Parameter Bearer Protocol Base Station IP Description Protocol type for PPP link Local IP Address of PPP link Value Range {PPP.0. Compression Enabled} [1. 255] [3. 65535] - Confidential and Proprietary Information of ZTE CORPORATION 29 .0. Unsupported} - This parameter is configurable only when data link layer protocol is HDLC. ZXSDR B8200 GU360 Ground Parameter Reference Parameter Type of MP Head MP Priority Description MP header sequence format MP priority Value Range {Long. Parameter Parameter User Label Port Type Parameter description is shown in the table below. InValid} Long: [1. Description Self-Defined Name Type of the link that bears global port Value Range 40 characters at most {IP over Ethernet. Short: [1. 4] Remarks – – Global Port Interface The related interface is shown in the figure below. 16]. Short. IP over PPP} Remarks – 30 Confidential and Proprietary Information of ZTE CORPORATION . IP/Static Router Layer Management IP Parameter Interface The related interface is shown in the figure below. Confidential and Proprietary Information of ZTE CORPORATION 31 .Chapter 2 Transmission Configuration Parameters Parameter Rack No./Shelf No. VLAN ID is “65535”./Slot No/Port ID VLAN ID Description Value Range Remarks - Location of the link that bears global port (rack/shelf/board/port) Global port VLAN ID [2. 4094] If VLAN is unused. Description Self-Defined name Global port ID IP address information of global port Bandwidth at global port Living time of IP packet Value Range 40 characters at most {The created global port} Remarks – - [0. 100000] [0. 255] – 32 Confidential and Proprietary Information of ZTE CORPORATION .ZXSDR B8200 GU360 Ground Parameter Reference Parameter Parameter User Label Global Port IP Address/Subnetwork Mask/Gateway Bandwidth Living time of IP Pack Parameter description is shown in the table below. Parameter Parameter User Label Parameter description is shown in the table below. 65535] Remarks Recommended parameter value is “1450”. GSM. WCDMA/GSM} {1 for Support. Description Self-Defined name Value Range 40 characters at most Remarks - Confidential and Proprietary Information of ZTE CORPORATION 33 .Chapter 2 Transmission Configuration Parameters Parameter Maximum length of traffic unit Radio Mode COS Flag Description MTU Value Range [0. 0 for Nonsupport} Static Router Interface The related interface is shown in the figure below. – – Traffic type over IP link COS type over IP link {WCDMA. 127] {The created global port} Valid IP address – Valid IP address Remarks – – – – Transmission Layer Management SCTP Association Interface The related interface is shown in the figure below.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Static Router ID Global Port Target IP Address Target Network Mask Next Hop Gateway Description Static router ID The global port that needs routing Target IP address Target network mask Next hop gateway Value Range [0. 34 Confidential and Proprietary Information of ZTE CORPORATION . – Rack No./Slot No.Chapter 2 Transmission Configuration Parameters Parameter Parameter User Label Association ID Parameter description is shown in the table below. 1] Remarks The maximum number of configured SCTP association links is 2. GSM} Confidential and Proprietary Information of ZTE CORPORATION 35 ./Shelf No. Radio Mode Location of the board which bears SCTP link Traffic type over SCTP link - {WCDMA. Description Self-Defined name Association ID Value Range 40 characters at most [0. discard Priority high.0 Local IP Address No. discard Priority middle. Service group 4.1 Local IP Address No. Service group 2.2 Local IP Address No. Service group 4.1 Remote IP Address No.3 Local IP Address Local Port Number Remote Port Number No. 65535] Valid IP Remarks - Valid IP – Valid IP – Valid IP – [1.2 Remote IP Address No. 5] [1. of SCTP link Local IP address of SCTP link (on RNC side) Local IP address of SCTP link (on RNC side) Local IP address of SCTP link (on RNC side) Local IP address of SCTP link (on RNC side) Number of SCTP streams IP link QoS Value Range Valid IP Valid IP Valid IP Valid IP [0. make the best of. 6] {EF service. 65535] [0. of SCTP link Remote port No.0 Remote IP Address No. 300] – 36 Confidential and Proprietary Information of ZTE CORPORATION . discard Priority middle. 30] - Maximum Retry Times Maximum Interval Time Heartthrob Interval Time Maximum retry times after packet loss Maximum interval time for retry after packet loss Time interval for sending SCTP status monitor information – [1. discard Priority high} [3.3 Remote IP Address Number of Input/Output Streams QoS Description Local IP address of SCTP link Local IP address of SCTP link Local IP address of SCTP link Local IP address of SCTP link Local port No.ZXSDR B8200 GU360 Ground Parameter Reference Parameter No. Service group 2. NCP+CCP} – – Confidential and Proprietary Information of ZTE CORPORATION 37 . CCP.Chapter 2 Transmission Configuration Parameters SCTP Stream Interface The related interface is shown in the figure below. 5] {NCP. Description Self-Defined name The corresponding SCTP link in stream parameter configuration Stream ID The user type that SCTP stream bears Value Range 40 characters at most {The created SCTP link} Remarks – Stream ID User Type [0. Parameter Parameter User Label Association ID Parameter description is shown in the table below. 1] Configured IP address 38 Confidential and Proprietary Information of ZTE CORPORATION ./Shelf No. Parameter Parameter User Label Parameter description is shown in the table below. Link ID Base Station OMC IP Address [0. Description Self-Defined name The interface board which bears OMC-B connection ID of OMC-B link IP address of the interface used to transmit BS operation and maintenance data packet Value Range 40 characters at most - Rack No.ZXSDR B8200 GU360 Ground Parameter Reference OMC-B Link Interface The related interface is shown in the figure below./Slot No. Chapter 2 Transmission Configuration Parameters Parameter Base Station OMC Gateway Description Destination gateway for operation and maintenance data sent by BS QoS of IP link Value Range Valid IP address IP Tos [0. Description Self-Defined name Value Range 40 characters at most Remarks - Confidential and Proprietary Information of ZTE CORPORATION 39 . 255] Clock Configuration IP Clock Interface The related interface is shown in the figure below. Parameter Parameter User Label Parameter description is shown in the table below. 3600] - Durative DELAY REQUEST Time [600. Service group 2. two step} [600. discard priority high. Service group 2.ZXSDR B8200 GU360 Ground Parameter Reference Parameter Sync server IP Address Subnet Mask Description IP address of clock synchronization server Subnet mask of clock synchronization server Gateway address of clock synchronization server IP address for BS clock QoS of IP link Value Range Valid IP Remarks - Subnet mask – Gateway Address Valid IP – IP Address for Base Station Clock IP Tos {The created IP} {EF service. 40] – SYNC Interval Time Requested time interval for sending SYNC (SYNC sent by remote end) Requested time interval for sending DELAY REQUEST (DELAY REQUEST sent by remote end) Sending mode Requested durative time for sending SYNC (SYNC sent by remote end) Requested durative time for sending DELAY REQUEST (DELAY REQUEST sent by remote end) - DELAY REQUEST Interval Time [30. 3600] - 40 Confidential and Proprietary Information of ZTE CORPORATION . 120] - Sending Mode Durative SYNC Time {one step. make the best of. Service group 4. discard priority high} [1. Service group 4. discard priority middle. discard priority middle. Figures Confidential and Proprietary Information of ZTE CORPORATION 41 . ZXSDR B8200 GU360 Ground Parameter Reference This page is intentionally blank. 42 Confidential and Proprietary Information of ZTE CORPORATION . Tables Confidential and Proprietary Information of ZTE CORPORATION 43 . 44 Confidential and Proprietary Information of ZTE CORPORATION .ZXSDR B8200 GU360 Ground Parameter Reference This page is intentionally blank. Communication Control Port GSM .Point-to-Point Protocol QoS .Stream Control Transfer Protocol VLAN .Quality of Service RNC .Operation & Maintenance Module PPP .List of Glossary AISG .Site Alarm Module SCTP .Maximum Transmission Unit NCP .Virtual LAN VSWR .Wideband Code Division Multiple Access Confidential and Proprietary Information of ZTE CORPORATION 45 .Node B Control Port OMM .Voltage Standing Wave Ratio WCDMA .Global System for Mobile communication HDLC .High-level Data Link Control MTU .Remote Radio Unit SA .Radio Network Controller RRU .Antenna Interface Standards Group CCP .