VPC (Flowserve)

Pump size & type Based on curve no.Number of stages Customer Item number Service Flowserve reference Date : : : : : dargroup Default 0.1 February 27, 2014 Capacity Head Specific gravity Pump speed Test tolerance : 08EML : EC-2363 : 19 : : : : : 10.6 l/s 100.00 m 1.000 1480 rpm Hydraulic Institute Level A CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY. Bowl performance shown below is corrected for materials, viscosity and construction. Bowl head of 100.12 m corresponds with 100.0 m head at discharge flange adjusted for elevation and friction losses. Copyright © 2009 Flowserve. All rights reserved. FlowSelex v2.2 1 of 5 5 N Min thrust .0 cP / 1.4 kW Driver power : 14.g Material column code Pump / Stages Based on curve no. Copyright © 2009 Flowserve.8 % Total head ratio (rated/max) : 95.g 0.0 m head at discharge flange adjusted for elevation and friction losses. CAPACITY.8 .g Dischg Head Dischg Region MAWP : 1965.9 % Power: (Rated / Max) : 13.0 mm Impeller dia ratio (rated/max) : 98. 156.00) : 78. HEAD. Bowl head of 100.0 mm 146. All rights reserved.1 kPa.0 kPa. FlowSelex v2.8 N Max thrust .2 2 of 5 .12 m corresponds with 100. PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS. 2014 / 19 Materials / Specification : B30 Other Requirements Hydraulic selection : No specification Construction : No specification Test tolerance : Hydraulic Institute Level A Driver Sizing : Max Power(MCSF to EOC)with SF Liquid Liquid type Liquid description Temperature / Spec.000 / Performance Pump speed : 1480 rpm NPSH required (NPSHr) : 0.Hydraulic Datasheet Customer Customer reference Item number Service : dargroup : Default : : Operating Conditions Capacity Water capacity (CQ=1.0 kPa.9 kW / 20.g Impeller diameter : Rated / Maximum / Minimum : 152.00) NPSH available (NPSHa) NPSHa less NPSH margin Maximum suction pressure Rated suction pressure : : : : : : : : : 10.8 m Hydraulic power : 10. viscosity and construction.g Suction Regions MAWP : 1965.8 l/s Suction specific speed : 8930 US units Thrust .2 % Flow at BEP : 11.Runout flow / Max Suction : 3166..0 hp Bowl Pressure : 1449.Rated flow / Rated suction : 4776.98 m Head rise to shut off : 47.4 kW Efficiency (CE=1.2 l/s Flow as % of BEP : 94. Flowserve reference Date : : : : 08EML EC-2363 Default 0..6 l/s 100.3 kPa.0 % Maximum head @ rated dia : 147. AND EFFICIENCY.0 kPa.5 N (A negative thrust value indicates an upthrust condition) CURVES ARE APPROXIMATE. Gravity Viscosity / Vapor pressure : Other : : 16 C : 1.g Bowl & column hydrotest : 1811.g (based on shut off and Rated specific gravity @ Cut dia) Maximum allowable : 3674.4 % Minimum continuous flow : 3.1 February 27. Bowl performance shown below is corrected for materials.Shut off / Rated suction : 6767.00) Normal capacity Total Developed Head Water head (CH=1.9 kPa.0 kPa.2 kW / 13.00 m Ample 0. All rights reserved. FlowSelex v2.2 mm Lineshaft diameter : 31.6 mm Column pipe length : 0.1 : February: 27.23 m Column section length : 2743. Flowserve reference Date : 08EML : EC-2363 : Default 0. 2014 February Driver Information : : 20.2 mm Lineshaft brg spacing : 2743.Fab'd / Above grade Suct and Dischg Thrust Stand Size : - Manufacturer Power / SF (Req' / Act') Vertical shaft type Driver Type Frame size / Base dia Enclosure Duty type Efficiency type Hazardous area class Explosion 'T' rating Volts / Phase / Hz Amps-full load/locked rotor Motor starting Insulation Temperature rise Bearings / Lubrication Motor mounted by Motor Thrust rating down/up 1.0 : : : : : : : : : : /0 /Direct on line (DOL) //- /- Bowl Impeller Bowl bearing Bowl shaft Bowl wear ring Impeller wear ring Column Lineshaft Bearing retainer Lineshaft bearing Lineshaft sleeve Discharge head Support plate : : : : : : : : : : : : Materials 416 stainless steel - Arrangement Size Manufacturer / Type Material code (Man'f/API) Gland material Auxiliary seal device Seal flush plan Seal flush construction Seal Information : : : : : : : : Paint and Package //- Pump paint Support plate paint Shipment type : : : Additional information Complete pump Mounting plate Driver(nett) Hydrostatic test Performance test NPSH test Weights (Approx.Construction Datasheet Customer Customer reference Item number Service : dargroup : Default : : Pump Pump / Stages / Stages Based on curve no.2 3 of 5 .7 mm Lineshaft coupling type : Threaded coupling Lineshaft bearings.) : : : Testing : : : - Pit / sump depth : Pump length : 3.0 hp / 14.00 in //"TF" .9 kW : : : : / 19 Construction Bowl construction / lined : Threaded / Lined bowls Impeller type : Semi-open & closed impellers Impeller fastening : Colleted Column construction : Column flange spec'n : Taneytown Specification Column dia (nominal) : 101.5 mm Notes - Copyright © 2009 Flowserve. 2014 27. qty : 1 Lineshaft construction : Lineshaft lubrication : Disch size/rating/face : 4.53 m mounting surface to bell/strainer bottom Available well diameter : Max dia below mtg surface : 190. 00 m : 14.6 l/s / 100. All rights reserved.2 Copyright © 2009 Flowserve.0 hp / : -/0/Drawing number Date Certified by / Date : Seal type Seal flush plan : : February 27.Full Page GA Drawing All dimensions are in millimeters unless otherwise specified Customer Item number Service Customer PO # Flowserve reference : dargroup : : : : Default 0.9 kW / 20.1 Pump size & type Pump speed / Stages Flow / Head Driver power / Frame Volts / Phase / Hz : 08EML : 1480 rpm / 19 : 10. 4 of 5 . 2014 : : : FlowSelex v2. Number of stages Capacity Head : 10.Customer Item Number Service Flowserve Reference Date : dargroup : : : Default 0.00 m Specific gravity Pump speed : 1. 2014 Pump size & type Based on curve no.2 5 of 5 . All rights reserved.6 l/s : 100.1 : February 27. FlowSelex v2.000 : 1480 rpm : 08EML : EC-2363 : 19 Copyright © 2009 Flowserve.