Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide V1.2 Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Disclaimer i Getting Started ii [01] Engine 1 Idle Speed – Raise/Lower 1-1 EGR Valve – Reduce Flow (Diesel Only) 1-1 ECU Swapping (Immobiliser Coding) 1-2 Throttle Body Alignment – KW-1281 and KWP-2000 (Petrol Only) 1-3 Cruise Control –Activation 1-4 [02] Auto Trans 2 Coding 2-1 01M (4-Speed) – Basic Settings 2-1 [03] ABS Brakes 3 Coding 3-1 ABS Pump Bleeding 3-1 Steering Angle Sensor Calibration – Bosch 5.7 & 8.0 3-2 [08] Auto HVAC 4 Basic Settings 4-1 Output Tests 4-1 [09] Cent. Elect. 5 Coding 5-1 Tow Bar Electrics – Activate/Deactivate 5-2 Drip Wiper Function 5-2 One Touch Indicators 5-3 Terminal 30G – Interior Power Supply Discharge Protection 5-4 Heated Windscreen Activation Time 5-5 Heated Wing Mirror Heating Time 5-5 Rear Screen Heating Time 5-6 Boot Lid Remote Unlocking 5-6 Headlight Washer Activation 5-7 [15] Airbags 6 Airbag Activation/Deactivation 6-1 [17] Instruments 7 Coding 7-1 Output Test 7-2 Instrument Cluster Swapping (Immobiliser Coding) 7-3 Key Programming / Matching 7-4 Service Schedule – Adaptations and Resets (2002-2006) 7-5 Service Schedule – Adaptations and Resets (2006-2008) 7-6 [44] Steering Assist 8 Steering Weight – Heavier/Lighter 8-1 [46] Central Conv. 9 Coding 9-1 Anti-Hijack - Auto Lock/Unlock, Bleep and Indicator Flash 9-2 Selective Unlocking 9-3 Remote Fob Syncing 9-4 [55] Xenon Range 10 Headlamp Adjustment – Manual Adjustment 10-1 Change Log Version 1.2 Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Disclaimer By using this guide, you acknowledge that this is provided “as is” and any use of this guide is at your own full risk. It has been tested (where possible) by myself, but I cannot guarantee that everything contained in this guide will function correctly on all variants of the Seat Ibiza/Cordoba (6L). Therefore, I will not be held responsible for any damage that may occur to your vehicle. Remember, before changing any coding or values on your vehicle, it is best practice to record the existing value, so it can be reverted back if you are to encounter any issues. As the Seat Ibiza/Cordoba (6L) models are built on the same PQ24 platform as the Volkswagen Polo (9N) and Skoda Fabia (6Y), there may be a possibility that parts of this guide may work with similar effects on these models as well. This has not been tested. NOTE – This guide was produced using various sources including the Internet and through experimentation. The actual guides contained within are free to use by any person however, modification of this guide and subsequent publishing or sale without my permission will be in breach of copyright. Version 1.2 In this case. Buttons are always listed as the description then a number. These only have to be selected once. [Login – 11] = This shows a specific button within a control module that needs to be selected. Enter “12233” = This shows what text or value you need to enter within a text window. Within each module. can activate or change various features on your Seat Ibiza or Cordoba.ross-tech.ross-tech.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Getting Started Welcome to the Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide. If you are unfamiliar with the basic workings of VCDS. for example 12233 not “12233”.2 . This guide covers known tips and tricks and was made using VCDS 12. Only enter what is shown WITHOUT apostrophes. Enter Channel/Group “03” = This shows what text or value you need to enter within a group or channel text box. So what is VCDS? VCDS (VAG-COM Diagnostic System) is powerful Windows-based software that allows a PC to act as a diagnostic tool for most VW/Audi/SEAT/Skoda vehicles from 1994-current day.12.html How to use this guide For ease of use. [Do It!] [Cancel] = These are action buttons within various screens throughout VCDS. Version 1. [01 – Engine] = This is the control module as displayed within the „VCDS Select Control Module‟ window. not “03” or “3”.com/vcds/tour/main_screen. this guide is broken down into the control modules as seen in VCDS. blip the accelerator to settle the idle revs. check out Ross-Tech‟s fantastic VCDS User Manual .http://www. VCDS-Lite can be downloaded for free from www. Key Below is a breakdown of the different commands used throughout this guide. unless it is registered.net and can be used with a compatible FTDI FT232 Cable from eBay etc… however. the owner. The control modules are always listed as a number then the description. there are different settings or Adaptations that can be made along with a flow chart of how to do this. Only enter what is shown WITHOUT apostrophes. This guide was produced so that you. for example 03 or 3. features are very limited and will effect what you can do throughout this guide. #Blip Accelerator Pedal = This is a physical action that has to be carried out by the user. Alter the speed to the idle speed you like (Idle speeds will vary dependant on engine). Whilst engine is running. Air conditioning turned off (ECON).2 . As long as the new number within (Stored Value) and (New Value) is less than “33768” you have reduced the flow through the EGR as much as the ECU will let you. THIS SIMPLY REDUCES THE AMMOUNT OF EXHAUST GASES RECIRCULATED AS THE EGR VALVE IS STILL OPERATIONAL. Don‟t worry. [Save] Version 1. Whilst engine is running. at idle. [Test] [Save] EGR Valve – Reduce Flow (Diesel Only) NOTE – THIS IS NOT AN EGR DELETE. [Up] raises and [Dn] lowers the idle speed. Conditions With engine coolant temp above 70c. at idle. Procedure [01 – Engine] [Adaptation – 10] Enter Channel 01 (02 for TDI engines) Now you will see a group of numbers in (Stored Value) and (New Value). #Blip Accelerator Pedal Enter “32768” [Test] – You may see a number that is slightly higher than “32768”. Procedure [01 – Engine] [Login – 11] Enter “12233” [Do It!] [Adaptation – 10] Enter Channel “03” – You should see “33768” in (Stored Value) and (New Value).Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [01] – Engine Idle Speed – Raise/Lower Conditions With engine coolant temp above 70c. Conditions Replacement ECU installed in the car.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide ECU Swapping (Immobiliser Coding) Description This is used to program a replacement ECU to your vehicle and maintaining the Immobiliser. 01234) [Do It!] [Adaptation – 10] Enter Channel “50” [Read] Enter “0” – Then your 4 digit SKC of the OLD (ORIGINAL) ECU (e.Value may change to “32000”.08] Enter Channel “24” [Go!] Ensure the lock times in boxes (1) (2) (3) (4) are “0. [Save] [Done. Blocks . MUST HAVE THE SECURITY KEY CODE (SKC) FOR OLD (ORIGINAL) AND REPLACEMENT (NEW OR USED) ECU. Procedure [17 – Instruments] [Meas. IF THE VALUES ARE NOT “0.0” DO NOT SWITCH OFF THE IGNITION! ALLOW THE CAR TO SIT WITH IGNITION ON FOR THE NUMBER OF MINUTES INDICATED IN BOXES 1-4. [Done.g. All relevant coding information transferred to replacement ECU.2 . Battery voltage at least 12v. 01234) within (New Value). With ignition on. do not start the car. [TEST] . Go Back – 06] [01 – Engine] [Login – 11] Enter “0” – Then your 4 digit SKC of the REPLACEMENT ECU (e.0”.g. Go Back] Version 1. this is normal. Go Back] [Close Controller. Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switch to basic settings. [Switch to Meas. Procedure [01 – Engine] [Basic Settings – 04] Enter Group “60” [Go!] It should say "Basic Settings: OFF" on the top of your screen [ON/OFF/Next] It should now say "Basic Settings: ON" on the top of your screen. THERE ARE TWO WAYS THIS CAN BE DONE.2 . IF THE FIRST DOESN‟T WORK. Do not touch the accelerator throughout this whole procedure. Procedure [01 – Engine] [Measuring Blocks – 08] Enter Group “60” [Go!] [Switch to basic settings] Once you do this you will see the top right display say ADP RUN. KW-1281 Conditions With ignition on. You will see the values change and hear the TB cycle for the first few seconds then it will stop. do not start the car. [ON/OFF/Next] [Done. TRY THE SECOND. Leave it for about 30 seconds. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Do not touch the accelerator throughout this whole procedure.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Throttle Body Alignment – KW-1281 and KWP-2000 (Petrol Only) NOTE – THIS CAN ONLY BE CONDUCTED ON A VEHICLE THAT IS DRIVE-BY-WIRE (DBW). do not start the car. Blocks] KWP-2000 Conditions With ignition on. Go Back] Version 1. Leave it in Basic Settings for about 30 seconds. Version 1. Go Back – 06] #Turn Ignition Off This is cruise control now activated. Procedure [01 – Engine] [Login – 11] Enter “11463” [Do It!] [Close Controller.2 .Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Cruise Control – Activation Conditions With ignition on. do not start the car. [Do It!] [Close Controller. Go Back] #Release Accelerator Pedal Version 1. do not start the car.2 . Go Back – 06] 01M (4-Speed) – Basic Settings Conditions With ignition on. Procedure [02 – Auto Trans] [Coding – 07] Record the original 5-digit value within (Software Coding). No fault codes present within gearbox ECU.04] Enter Group “00” [Go!] #Press Accelerator Pedal and hold down for 5 seconds.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [02] – Auto Trans Coding Conditions With ignition on. [Done. Only touch the accelerator when instructed below. Procedure [02 – Auto Trans] [Basic Settings . do not start the car. 01M 000?x: DSP Mode (Dynamic Shift Points) 0 = DSP active 1 = DSP inactive 000x?: Transmission Mode 0 = Factory Mode (Adaptive Transmission Mode) 1 = Force Economy Mode (lower Shift Points) 2 = Force Sport Mode (higher Shift Points) Set the desired value. 0 NOTE – READ ABOUT THE FULL PROCEDURE PRIOR TO CARRYING OUT THE BASIC SETTINGS AS THERE IS MORE PHYSICAL ACTIONS INVOLVED.Follow the onscreen instructions.ABS Brakes] [Basic Settings .2 . Go Back] Version 1.04] Enter Group “10” = Bosch 5. Procedure [03 . Procedure [03 – ABS Brakes] [Coding – 07] Record the original 5-digit value within (Software Coding).7 & 8.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [03] – ABS Brakes Coding Conditions With ignition on. do not start the car. Front wheels supported off the ground and brake bleed nipples easily accessible. [Done.0 00060 = AME/AQW/ATZ (Manual) 00124 = AMF/AUA/BKY/BBY/BBZ (Manual) 00125 = AMF/AUA/BKY/BBY (Automatic) NONE AVAILABLE 00188 = ATD/ASZ/AMF/AZL/BBX/BJX/BKV/ BLT/AXR (Manual) Set the desired value. Conditions With ignition on.7 Enter Group “02” = Bosch 8. Go Back – 06] ABS Pump Bleeding – Bosch 5. do not start the car. Only needed if ABS Pump has run dry and not needed during normal fluid change.7 BOSCH 8.0 [Go!] It will then display „PRESS AND HOLD PEDAL‟ . BOSCH 5. [Do It!] [Close Controller. Recommend only doing a basic setting adjustment if you‟re having issues.(Steering Angle Sensor -G85-) Specification should be 0. Go Back] [Security Access . [Meas.0 Conditions With ignition on.0 ° with a Tolerance of ±5. Procedure [03 .7 & 8. Blocks . [Done.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Steering Angle Sensor Calibration – Bosch 5. [Done. Go Back] [Fault Codes .08] Enter Group “05” [Go!] Look within box (1) .02] Ensure you record and clear all fault codes present. Go Back] [Close Controller.2 . Go Back . Go Back] #Turn steering wheel at least ¼ left and back straight ahead to engage the PAS Motor.ABS Brakes] [Fault Codes . [Done. Don‟t worry if any faults reappear upon rescanning.04] Enter Group “01” [Go!] [Done.16] Enter “40168” [Do It!] [Basic Settings .02] All fault codes in relation to the G85 should have disappeared. engine running. NOTE .0 ° (when straight).06] Version 1. Conditions With ignition on. Procedure [08 – Auto HVAC] [Basic Settings – 04] Enter Group “01” [Go!] This will now run through a sequence of moving all the motors to reset the learnt positions. Go Back] Version 1. When this is complete the values contained in the boxes will return to “0” [Done. Procedure [08 – Auto HVAC] [Output Tests – 03] [Go!] This will now run on Output Test step by step. [Done.2 . do not start the car.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [08] – Auto HVAC Basic Settings Description This is the interior heating system reset and calibration sequence. Conditions With ignition on. do not start the car. Go Back] Output Tests Description This is a sequential test to ensure all elements of the heating system are functioning correctly. Conditions With ignition on.2 . Coding Description This allows you to change some of the basic functionality within the Central Electronics Module. 6Q?-937-049-B and below 6Q?-937-049-C and above +00001 = Trailer Hitch installed +00001 = Trailer Hitch installed +00002 = Trunk Lid Remote Unlocking +00002 = Trunk Lid Remote Unlocking installed installed +00004 = Electric Load Management active +00004 = Electric Load Management active +00008 = Interior Light Control +00008 = Interior Light Control +00016 = 4-door Chassis +00016 = Seat Backrest Recognition installed +00032 = Heated Front Seats installed +00032 = Heated Front Seats installed +00064 = Heated Front Windshield installed +00128 = Heated Mirrors installed +00128 = Heated Mirrors installed +00256 = Headlight Washers installed +00256 = Headlight Washers installed +00512 = Rain Sensor installed +00512 = Rain Sensor installed +01024 = Trunk Lid Remote Unlocking +08192 = Rear Windshield Wiper with Comfort impulse driven Function installed +08192 = Rear Windshield Wiper with Comfort +16384 = Electric Fuel Pump Relay installed Function installed +16384 = Electric Fuel Pump Relay installed Note: The coding is the sum of the Note: The coding is the sum of the individual options. do not start the car.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [09] – Cent.] [Coding – 07] Record the original 5-digit value within (Software Coding). individual options. Procedure [09 – Cent. [Do It!] [Close Controller. Elect. Elect. Go Back – 06] Version 1. Set the desired value. 2 . For example. Setting the value to “0” disables the function. Conditions With ignition on. do not start the car. Go Back – 06] Drip Wiper Function NOTE – THIS MAY NOT WORK ON ALL MODELS. Procedure [09 – Cent. Conditions With ignition on.] #Note the “VAG Number” [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] For VAG Number “6Q?-937-049-B” or below = Enter Channel “08” For VAG Number “6Q?-937-049-C” or above = Enter Channel “07” [Read] Set the desired value corresponding to each second delay for the last drip wipe. Go Back] Version 1. [Test] [Save] [Done. “4” will set it to function after a 4 second delay. Elec. +00001 = Activate Set the desired value.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Tow Bar Electrics – Activation/Deactivation NOTE – THIS MAY NOT WORK ON ALL MODELS. do not start the car. Elec. [Do It!] [Close Controller.] [Coding – 07] Record the original 5-digit value within (Software Coding). LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent. 2 . Go Back] Version 1. 0 is disabled) [Test] [Save] [Done. Elec. do not start the car. Conditions With ignition on. Elec. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent. 5 is maximum. Go Back] Terminal 30G – Interior Power Supply Discharge Protection Description Terminal 30G cuts the power to prevent discharge of the vehicle battery when the interior lights are left on and ignition switched off.] [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] For VAG Number “6Q?-937-049-B” or below = Enter Channel “07” For VAG Number “6Q?-937-049-C” or above = Enter Channel “06” “0” “1” “2” “3” “4” “5” = Number of flashes (3 is default. do not start the car.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide One Touch Indicators Conditions With ignition on.] [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] Enter Channel “01” [Read] Set the desired value between 1-253 (1-173 mins) Standard = 44 (30 mins) [Test] [Save] [Done. do not start the car. Go Back] Heated Wing Mirror Activation Time Conditions With ignition on. Elec. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Heated Windscreen Activation Time Conditions With ignition on.2 .] [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] Enter Channel “02” [Read] Set the desired value between 1-253 (1-173 mins) Standard = 29 (20 mins) Special = 254 (Infinite) [Test] [Save] [Done. Go Back] Version 1. do not start the car. Elec.] [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] Enter Channel “03” [Read] Set the desired value between 1-253 (1-173 mins) Standard = 29 (20 mins) Special = 254 (Infinite) [Test] [Save] [Done. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent. Elec. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent.] [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] Enter Channel “04” [Read] Set the desired value between 1-253 (1-173 mins) Standard = 29 (20 mins) Special = 254 (Infinite) [Test] [Save] [Done. do not start the car.6 secs) Standard = 3 (1 secs) [Test] [Save] [Done.] [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] Enter Channel “05” [Read] Set the desired value between 1-253 (0.32-81. do not start the car. Elec.2 .Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Rear Screen Heating Time Conditions With ignition on. Go Back] Version 1. Go Back] Boot Lid Remote Unlocking Conditions With ignition on. Elec.] #Note the “VAG Number” [Security Access – 16] Enter “21343” [Do It!] [Adaptation – 10] For VAG Number “6Q?-937-049-B” or below = Enter Channel “09” For VAG Number “6Q?-937-049-C” or above = Enter Channel “08” [Read] Set the desired value between 0-255 secs Standard = 5 secs [Test] [Save] [Done. LOGIN ONLY REQUIRED FOR VAG NUMBER “6Q?-937-049-B” OR BELOW! Procedure [09 – Cent. do not start the car. Go Back] Version 1.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Headlight Washer Activation Conditions With ignition on.2 . Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [15] – Airbags Airbag Activation/Deactivation **WARNING – ACTIVATE AND DEACTIVATE AT YOUR OWN RISK Description This is useful if you‟re planning on changing or removing the factory fitted seats for aftermarket options or replacing the original steering wheel. 6Q0-909-605-VW5 and higher only (VW5. Version 1. VW52 and VW61). Go Back] NOTE – WITH ANY OF THE SAFETY SYSTEMS DEACTIVATED. VW51. [Test] [Save] [Done. Conditions With ignition on. do not start the car.2 . Procedure [15 – Airbags] [Adaptation – 10] Enter Channel “01” = Passenger Airbag (Dash) Enter Channel “02” = Driver Airbag (Wheel) Enter Channel “03” = Passenger Side Airbag (Seat) Enter Channel “04” = Driver Side Airbag (Seat) Enter Channel “05” = Passenger Seat Belt Tensioner (Front) Enter Channel “06” = Driver Seat Belt Tensioner (Front) [Read] “0” = Activated “1” = Deactivated Set the desired value. THE AIRBAG LIGHT WILL FLASH WHEN THE IGNITION IS TURNED ON FOR APPROXIMATELY 10 SECONDS AND THEN TURN OFF UNLESS THERE IS A FAULT. [Do It!] [Close Controller.2 . Conditions With ignition on.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [17] – Instruments Coding Description This allows you to change the basic functionality of your instrument cluster. Procedure [17 – Instruments] [Coding – 07] Record the original 5-digit value within (Software Coding). 2002-2006 2006-2008 ??xxx: Options ??x0x: Options +01 = Brakepad Warning active +01 = Brakepad Warning active +02 = Seatbelt Warning active +02 = Seatbelt Warning active +04 = Washer Fluid Warning active +04 = Washer Fluid Warning active xx?xx: Country xx?0x: Country 0 = Germany 0 = Germany 1 = Europe 1 = Europe 4 = Great Britain (GB) 4 = Great Britain (GB) 6 = Saudi Arabia 6 = Saudi Arabia 7 = Australia (AUS) xxx?x: Cylinders 3 = 3-Cylinders xxx0?: Speed Impulse Number (K-Value) 4 = 4-Cylinders 1 = Engine Code BPX/BUK/BBU/BLZ/BJX/ BKV xxxx?: Speed Impulse Number (K-Value) 2 = Engine Code ATD/AXR/BMT/BNV/BMS 2 = Engine Code BJX/BKV 5 = Engine Code BBY/BKY/BBZ/BBX/BAH/ 3 = Engine Code BBY/AUA/BKY ASZ/BLT/BNM/BTS/BXV/BXW 4 = Engine Code AMF/BAY/ATD/AXR 5 = Engine Code AZL/BBX/ASZ/BLT 6 = Engine Code BBZ/AUB 7 = Engine Code BNV/BMS/BNM/AZQ/BME/ BAH Set the desired value. Go Back – 06] Version 1. do not start the car. 2 . Go Back – 06] Version 1. do not start the car.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Output Test Description This is used to run the instrument cluster through a full output test. Procedure [17 – Instruments] [Output Tests – 03] [Start / Next] The instrument cluster will now go through the following procedure. It is useful if you have removed the cluster for repair or modification. Rev Counter Sweep Temp Gauge Sweep Fuel Gauge Sweep Speedometer Sweep Mileage and OBC Screen Temp Gauge Warning Low Fuel Warning Light Immobiliser Warning Light Oil Warning Light Handbrake Warning Light Warning Chimes Etc… [Close Controller. Conditions With ignition on. This process includes a full needle sweep and hold of the dials and illumination of all the lights so you can set the positions correctly. with the option to select the next stage. Battery voltage at least 12v. 01234) within (New Value). this is normal.g.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Instrument Cluster Swapping (Immobiliser Coding) Description This is used to program a replacement instrument cluster to your vehicle. Version 1.08] Enter Channel “24” [Go!] Ensure the lock times in boxes (1) (2) (3) (4) are “0. Blocks . [Save] [Done. Conditions Replacement cluster installed in the car. IF THE VALUES ARE NOT “0. [TEST] .0”. MUST HAVE THE SECURITY KEY CODE (SKC) FOR OLD (ORIGINAL) AND REPLACEMENT (NEW OR USED) CLUSTER. [Done.0” DO NOT SWITCH OFF THE IGNITION! ALLOW THE CAR TO SIT WITH IGNITION ON FOR THE NUMBER OF MINUTES INDICATED IN BOXES 1-4. do not start the car.2 .Value may change to “32000”. Go Back] [Login – 11] Enter “0” – Then your 4 digit SKC of the REPLACEMENT CLUSTER (e. Go Back] NOTE – Any old keys will automatically be removed from the Immobiliser so will need to be matched (See Key Programming / Matching – Next Page) * If “FAIL” does appear on the Odometer double check the SKC you entered is correct and start from the very beginning before attempting to login again. With ignition on.g. 01234) [Do It!] #Ensure „FAIL‟ doesn‟t appear on the Odometer * [Adaptation – 10] Enter Channel “50” [Read] Enter “0” – Then your 4 digit SKC of the OLD (ORIGINAL) CLUSTER (e. Procedure [17 – Instruments] [Meas. Enter Channel “24” [Go!] Ensure the lock times in boxes (1) (2) (3) (4) are “0. #Turn off ignition and remove key. Procedure [17 – Instruments] [Meas. [Done. IF THE VALUES ARE NOT “0. Go Back] [Login – 11] Enter “0” – Then your 4 digit SKC (e. Repeat until all the keys are matched.g. Enter the number of all keys to be matched within (New Value). #Insert next key and turn ignition on. Blocks . then the key cannot be matched to the immobiliser. [Done.0” DO NOT SWITCH OFF THE IGNITION! ALLOW THE CAR TO SIT WITH IGNITION ON FOR THE NUMBER OF MINUTES INDICATED IN BOXES 1-4.0”. MUST HAVE THE SECURITY KEY CODE (SKC). with ignition on. 01234) [Do It!] [Adaptation – 10] Enter Channel “21” [Read] (Stored Value) will show the number of keys currently matched to the Immobiliser. do not start the car. Go Back] Version 1. Can match up to 8 keys.08] Enter Channel “22” [Go!] The value in box (3) must be “1”. ALL KEYS NEEDING TO BE MATCHED MUST BE PRESENT. The Immobiliser Warning Light will illuminate again until the key in the ignition is matched. [Save] [To be completed within 60 seconds] The Immobiliser Warning Light will remain illuminated until the key in the ignition is matched. If it is not. NOTE – Any old keys will automatically be removed from the Immobiliser so will need to be matched at the same time.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Key Programming / Matching Conditions New key inserted. Keep all keys to be matched separate from each other.2 . Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Service Schedule – Adaptations (2002-2006) Description This allows you to change or reset various reminders within your vehicle service schedule. [Test] [Save] [Done.000km) 06 Maximum Distance to Inspection “1” = Increments (1000km) “12” = Standard (12 months) 07 Maximum Time to Inspection “1” = Increments (months) “150” = Standard (15.000km) 05 Maximum Distance to Oil Service “1” = Increments (1000km) “15” = Standard (15.Key Matching See Key Matching “128” = Standard (7L of fuel) Tank Characteristic (Fuel Level 30 “120” – “136” = -2. Conditions With ignition on. do not start the car. Channel Values “0” = Reset 02 Service Reminder “1” = Service Due “100” = Standard 03 Consumption Correction “85” – “115” = Range “1” = Increments “1” = German / “2” = English / “3” = French 04 Language “4” = Italian / “5” = Spanish / “6” = Portuguese “15” = Standard (15.0 Sensor) “1” = Increments (Ohm = 1/4L of fuel) 39 Oil Level Sensor Adaption Oil Level Sensor Installed [Read] Set the desired value.0 / +2.2 .000km) 10 Distance to Oil Service “1” = Increments (100km) “300” = Standard (30. Go Back] Version 1. Procedure [17 – Instruments] [Adaptation – 10] Enter Channel “??” No.000km) 11 Distance to Inspection “1” = Increments (100km) “360” = Standard (360 days) 12 Time to Inspection “1” = Increments (days) 21 Immobiliser . Channel Values “0” = Reset 02 Service Reminder “1” = Service Due “100” = Standard 03 Consumption Correction “85” – “115” = Range “1” = Increments “1” = German / “2” = English / “3” = French 04 Language “4” = Italian / “5” = Spanish / “6” = Portuguese “128” = Standard (7L of fuel) Tank Characteristic (Fuel Level 30 “120” – “136” = -2.0 / +2.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Service Schedule – Adaptations (2006-2008) Description This allows you to change or reset various reminders within your vehicle service schedule. [Test] [Save] [Done. Go Back] Version 1. do not start the car. Conditions With ignition on.000km) 43 Maximum Distance to Service “1” = Increments (100km) “00365” = Standard (365 days) 44 Maximum Time to Service “1” = Increments (days) [Read] Set the desired value.0 Sensor) “1” = Increments (Ohm = 1/4L of fuel) 40 Distance Since Service “1” = Increments (100km) 41 Time Since Service “1” = Increments (days) “00150” = Standard (15.2 . Procedure [17 – Instruments] [Adaptation – 10] Enter Channel “??” No. do not start the car. Procedure [44 – Steering Assist] [Coding – 07] Record the original 5-digit value within (Software Coding). Go Back – 06] Version 1.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [44] – Steering Assist Steering Weight – Heavier/Lighter Description This allows you to change the feel of the steering for a heavier sporty feel.2 . “10111” = Light “10121” “10131” = OEM “10141” “10151” = Heavy Set the desired value. We are only changing the 4 th digit throughout this procedure. [Do It!] [Close Controller. Conditions With ignition on. You should see a value similar to “10131” with the 4th digit (underlined) being either the same or different. or a lighter feel if you mainly do urban driving. [Do It!] [Close Controller. the Door Control Modules are now connected via LIN which results in different coding method. +00001 = Selective Locking inactive +00002 = 4-Doors +00016 = Central Locking installed (from MY 2008) +00016 = Central Locking without Power Windows installed (through MY 2007) +00064 = Central Locking with 2 Power Windows installed (through MY 2007) +00256 = Central Locking with 4 Power Windows installed (through MY 2007) Note: The Coding is the Sum of the individual Options.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [46] – Central Conv. do not start the car. Procedure [46 – Central Conv.2 . Set the desired value. Coding Description This allows you to change the basic settings of the Central Convenience Module. Go Back – 06] Version 1. Conditions With ignition on.] [Coding – 07] Record the original 5-digit value within (Software Coding). As of 2008. Bleep and Indicator Flash Description This allows you to alter the locking behaviour of your car. Go Back] NOTE – SOME MODELS MADE AFTER 2005 WILL NOT BE ABLE TO ACTIVATE THE LOCKING/UNLOCKING „CHIRP‟ AS THE MODULE DOES NOT EXIST. [Test] [Save] [Done. horn sounds (Activates/de-activates unlocking „chirp‟ or „bleep‟) Enter Channel “06” = Lock. horn sounds (Activates/de-activates locking „chirp‟ or „bleep‟) Enter Channel “07” = Unlock. do not start the car. Procedure [46 – Central Conv.2 . Version 1.Auto Lock/Unlock.] [Adaptation – 10] Enter Channel “03” = Auto Lock (When speed exceeds 10mph/15kph) Enter Channel “04” = Auto Unlock (When key is removed from ignition) Enter Channel “05” = Unlock. Conditions With ignition on. turn signals flash (Activates/de-activates unlocking indicator flash) Enter Channel “08” = Lock.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Anti-Hijack . turn signals flash (Activates/de-activates locking indicator flash) “1” = On “0” = Off Set the desired value. Procedure [46 – Central Conv. “00064” = Selective Unlocking Activated (3 door) “00065” = Selective Unlocking De-activated (3 door) “00066” = Selective Unlocking Activated (5 door/Cordoba) “00067” = Selective Unlocking De-activated (5 door/Cordoba) Set the desired value. Go Back – 06] Version 1. When this option is de-activated. do not start the car. twice to open all the doors. [Do It!] [Close Controller. Conditions With ignition on.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Selective Unlocking Description This allows you to change the selective unlocking feature on all models. all the doors open with one press of the unlock button. Selective unlocking is where you press the unlock button on the remote once to open the driver's door.2 .] [Coding – 07] Record the original 5-digit value within (Software Coding). Procedure [46 – Central Conv.2 . Go Back] Version 1. do not start the car. [Test] [Save] #Press the unlock button on each fob for at least 2 seconds [Done.] [Adaptation – 10] Enter Channel “00” [Read] Enter “0” . Conditions With ignition on.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Remote Fob Syncing Description This allows you to synchronise remote key fobs to the car. Adaptation of all keys must not exceed 15 seconds. All keys must be adapted in one procedure.This will erase all currently synced remote fobs from the car. [Test] [Save] Enter Channel “01” [Read] Enter the number of remote fobs that you will be syncing. [Done. In a dark area. headlight shining against a surface Procedure [55 – Xenon Range] [Basic Settings – 04] Enter Group “01” [Go!] Wait for approximately 10 seconds and “Adjust Headlights” should appear. #Manually adjust headlamps Enter Group “02” [Go!] Headlight adjustment should now be learned. Conditions With ignition on. do not start the car.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide [55] – Xenon Range Headlamp Adjustment – Manual Adjustment Description This allows you to alter the beam pattern on models fitted with Xenon headlights only. Go Back] Version 1.2 . Basic Settings [03] – ABS Brakes o Coding o ABS Pump Bleeding o Steering Angle Sensor Calibration – Bosch 5.Seat Ibiza/Cordoba (6L) (2002-2008) VCDS Guide Change Log Version 1.0 Corrected [09] – Cent. Elect.1 Added [17] – Instruments o Output Test [02] – Auto Trans o Coding o 01M (4 Speed) .0 Initial Release Version 1.2 .2 Added [01] – Engine o ECU Swap (Immobiliser Coding) [17] – Instruments o Instrument Cluster Swap (Immobiliser Coding) Changed [01] – Engine o Cruise Control Activation [17] – Instruments o Key Programming / Matching Minor Amendments.7 & 8. Version 1. Version 1. o One Touch Indicators Channels o Misprinted [Login – 11] should be [Security Access – 16] Minor Amendments.