Contents 1 Introduction ........................................................................................................ 1 1.1 1.2 1.3 1.4 2 3 Safety Precautions ................................................................................ 1 LEDs and Interfaces .............................................................................. 2 System Requirements ........................................................................... 3 Features ................................................................................................ 4 Hardware Installation ......................................................................................... 5 Web Configuration ............................................................................................. 7 3.1 3.2 Accessing the Router ............................................................................ 7 Status..................................................................................................... 9 3.2.1 3.2.2 3.2.3 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.4 3.4.1 3.4.2 3.4.3 3.4.4 3.4.5 3.4.6 3.5 3.5.1 3.5.2 3.5.3 3.5.4 3.5.5 3.6 3.6.1 3.6.2 3.6.3 3.6.4 3.6.5 Device Info.................................................................................. 9 System Log............................................................................... 10 Statistics.................................................................................... 11 Internet...................................................................................... 13 LAN........................................................................................... 24 Wireless .................................................................................... 29 6RD........................................................................................... 32 Firewall ..................................................................................... 33 Routing ..................................................................................... 33 NAT........................................................................................... 35 QoS........................................................................................... 39 VLAN ........................................................................................ 44 ADSL ........................................................................................ 46 ACL........................................................................................... 47 Filter.......................................................................................... 47 UPnP ........................................................................................ 51 DDNS........................................................................................ 52 CWMP ...................................................................................... 52 Administration ........................................................................... 54 Time Zone................................................................................. 54 Firmware................................................................................... 55 SysRestart ................................................................................ 56 Diagnostics ............................................................................... 57 i An ISO certified company Interface Setup .................................................................................... 13 Advanced Setup .................................................................................. 33 Access Management ........................................................................... 46 Maintenance ........................................................................................ 54 Teracom Limited User Manual for TDSL300W2 1 Introduction The TDSL300W2 (ADSL2+ CPE, Type W2) CPE is an ADSL2+ access device that supports multiple line modes. With four 10/100Base-T Ethernet interfaces at the user end, it provides high-speed ADSL2+ broadband connection to the Internet or Intranet for high-end users such as internet cafes and office users. The device provides high performance access to the Internet with a downlink of 24 Mbps and an uplink of 1-3 Mbps. As a WLAN AP or WLAN router, the device supports WLAN access to the Internet. It complies with the IEEE 802.11b/g/n specifications, WEP, WPA and WPA2 security specifications. 1.1 Safety Precautions Take the following instructions to prevent the device from risks and damage caused by fire or electric power: Use the type of power marked by the volume label. Use the power adapter packed in the device package. Pay attention to the power load of the outlet or prolonged lines. An overburden power outlet or damaged lines and plugs may cause electric shock or fire accident. Check the power cords regularly. If you find any damage, replace it at once. Proper space left for heat dissipation is necessary to avoid damage caused by overheating to the device. The long and thin holes on the device are designed for heat dissipation to ensure that the device works normally. Do not cover these heat dissipation holes. Do not put this device close to a place where a heat source exists or high temperature occurs. Avoid the device from direct sunshine. Do not put this device close to a place where it is overdamp or watery. Do not spill any fluid on this device. Do not connect this device to any PCs or electronic products, unless our customer engineer or your broadband provider instructs you to do this, because any wrong connection may cause power or fire risk. Do not place this device on an unstable surface or support. 1 An ISO certified company Teracom Limited The device has established a connection with the physical layer of the office end. Data is being transmitted on the LAN or data is being transmitted on the Internet in the bridged mode. LEDs Power Color Green Status On Off Red DSL Green Blinks On Slow Blinks Fast Blinks Internet Green On The device is handshaking with the physical layer of the office end. LAN4/3/ 2/1 Green On Blinks The LAN connection is normal and activated.User Manual for TDSL300W2 1. The device will do power on self-test. the WAN connection is failed (PPP dial-up is failed). . Blinks Off Red On Data is being transmitted on the Internet in the routing mode.2 LEDs and Interfaces Front Panel The following table describes the LEDs of the device. The device is powered off. In the routing mode. Teracom Limited 2 An ISO certified company Description The device is powered on or the initiation of the device is successful. The device has a successful WAN connection (PPP dial-up is successful) in the routing mode and no data is being transmitted on the Internet. No signal is being detected. The device is in the bridged mode. after the successful synchronization. the self-test is failed or the software is upgrading. LAN1/2/3/4 DSL RJ-45 interface for connecting to the Ethernet interface of PC or other Ethernet devices through the Ethernet cable. The device has successful WLAN connection. 1. Data is being transmitted on WLAN. Teracom Limited 3 An ISO certified company .3 System Requirements Recommended system requirements are as follows. the configuration is reset to the factory defaults. Windows ME. Windows Vista. MAC & Linux OS. Windows XP. Windows 7. The WLAN connection is failed. Then release it. Back Panel The following table describes the interfaces and buttons of the device. RJ-11 interface for connecting to the ADSL2+ interface or a splitter through the telephone cable. Reset keep the device powered on and push a paper clip in to the hole for over 3 seconds. Windows 2000. Reset to the factory defaults.User Manual for TDSL300W2 LEDs WLAN Color Green Status Off On Blinks Off Description The LAN connection of the device is failed. To reset to the factory defaults. A 10/100 base-T Ethernet card installed on your PC Operating system: Windows 98 SE. Items Power Description Power interface for connecting to the power adapter. TFTP. or Firefox 1.0 or higher. Various line modes External PPPoE dial-up access Internal PPPoE/PPPoA dial-up access 2684Bridged/2684Routed with dynamic ip or static ip Multiple PVCs (eight PVCs supported) DHCP server/relay Static route Network Address Translation(NAT) DMZ Virtual Server Universal plug and play (UPnP) Dynamic Domain Name Server(DDNS) One-level password and username Network Time Protocol(NTP) Firmware upgrading through Web.5 or higher etc.4 Features The device supports the following features. Netscape V4.User Manual for TDSL300W2 Web Browser like Internet Explorer V5.0 or higher. or FTP Resetting to the factory defaults through Reset button or Web Diagnostic test Web interface Telnet CLI IP/MAC/URL Filter Application layer service QOS Port binding Teracom Limited 4 An ISO certified company . 1. Connect the LAN interface of the device to the network card of a PC through an Ethernet cable (MDI/MDIX). Step 3 Plug one end of the power adapter to the wall outlet and connect the other end to the Power interface of the device. Connect the incoming line to the Line interface of the splitter. Modem: Connect to the ADSL jack of the device. Phone: Connect to a telephone set. Connection The application diagram for the connection of the CPE. The splitter has three interfaces: Line: Connect to a phone jack (RJ-11 jack). Step 2 Note: Use twisted-pair cables to connect with the hub or switch.TDSL300W2 User Manual 2 Hardware Installation Step 1 Connect the DSL Line (RJ-11 Cable) to DSL port of the CPE through splitter or without splitter. splitter and the telephone: Teracom Limited 5 An ISO certified company . Connect a phone to the Phone interface of the splitter through a RJ-11cable. PC. TDSL300W2 User Manual Connection diagram Teracom Limited 6 An ISO certified company . 3.1 Accessing the Router The following is detailed description of accessing the router for the first time.User Manual for TDSL300W2 3 Web Configuration This chapter describes router configuration using the Web-based configuration utility. In the Login page that is displayed. enter the username and password. Teracom Limited 7 An ISO certified company . Step 1 Step 2 Open the Internet Explorer (IE) browser and enter http://192.1. When you log in. You can check. the page shown in the following figure appears.1. configure and modify all the settings.168. The username and password of the administrator are admin and admin. Teracom Limited 8 An ISO certified company . the settings can be saved as per requirement.User Manual for TDSL300W2 Note: In the Web configuration page. click Status.2. such as Firmware Version.1 Device Info Choose Status > Device Info. System Log and Statistics. 3.User Manual for TDSL300W2 3. LAN. WAN.2 Status In the navigation bar. The page that is displayed shows the current status and some basic settings of the router. Teracom Limited 9 An ISO certified company . ADSL and other information. In the Status page that is displayed contains Device Info. In this page.2 System Log Choose Status > System Log.User Manual for TDSL300W2 3. the page shown in the following figure appears. Teracom Limited 10 An ISO certified company . you can view or refresh the system log.2. ADSL Statistics and WLAN Statistics.3.2. Collision. click Ethernet and the page shown in the following figure appears.1 Ethernet Statistics In the Traffic Statistic page. Error Frames and CRC Errors. The Statistics page that is displayed contains Ethernet Statistics.User Manual for TDSL300W2 3. you can view the statistics such as total Bytes. 3.3 Statistics Choose Status > Statistics. Teracom Limited 11 An ISO certified company .2. In this page. 3.User Manual for TDSL300W2 3. click ADSL and the page shown in the following figure appears. you can view the ADSL line statistics such as total PDUs. 3. In this page.2. you can view the WLAN statistics such as Transmit Frames Count. total Error Counts.2.2 ADSL Statistics In the Traffic Statistic page. Teracom Limited 12 An ISO certified company . Transmit Errors Count and Transmit Drops Count. click WLAN and the page shown in the following figure appears.3 WLAN Statistics In the Traffic Statistic page. In this page.3. 1 Internet Choose Interface Setup > Internet. 3. IPv4/IPv6 and Encapsulation.User Manual for TDSL300W2 3. Qos.3 Interface Setup In the navigation bar. Teracom Limited 13 An ISO certified company . Wireless and 6RD. Click Internet pane. click Interface Setup. In this page. The Internet page that is displayed contains ATM VC. LAN. The Interface Setup page that is displayed contains Internet. you can configure WAN interface of your router.3. the page shown in the following figure appears. User Manual for TDSL300W2 Teracom Limited 14 An ISO certified company . User Manual for TDSL300W2 The following table describes the parameters of this page: Field Description You can select a virtual circuit from the Virtual Circuit drop-list. Click PVCs Summary you can view eight PVCs (from PVC0 to PVC7), and only PVC0 status is activated by default. Status VPI VCI ATM QoS You can select Activated or Deactivated for currently selected virtual circuit. The virtual path between two points in an ATM network, ranging from 0 to 255. The virtual channel between two points in an ATM network, ranging from 32 to 4095. Select the Quality of Service types for this Virtual Circuit. The ATM QoS types include CBR (Constant Bit Rate), VBR (Variable Bit Rate) and UBR (Unspecified Bit Rate). These QoS types are all controlled by the parameters specified below, including PCR, SCR and MBS. You can choose CBR, UBR, rtVBR, or nrtVBR. PCR Peak cell rate (PCR) is the maximum rate at which cells can be transmitted along a connection in the ATM network. SCR Sustain cell rate (SCR) is the maximum rate that traffic can pass over PVC without the risk of cell loss. MBS Maximum burst size (MBS) is the maximum number of cells that can be transmitted at the PCR. IP Version Supporting IPv6. You can choose Dynamic IP Address, ISP Static IP Address, PPPoA/PPPoE or Bridge Mode. Teracom Limited 15 An ISO certified company IPv4/v6 Dual Stack Internet Protocol. You can select IPv4, IPv4/IPv6 or User Manual for TDSL300W2 If your ISP provides you with an IP address automatically, you may select Dynamic IP Address in the ISP encapsulation. Dynamic IP is typically used for Cable services. Please enter the Dynamic IP information accordingly. Teracom Limited 16 An ISO certified company User Manual for TDSL300W2 The following table describes the parameters of this page: Field Encapsulation Bridge Interface Description You can choose 2684 Bridged IP LLC, 2684 Bridged IP VC-Mux, 2684 Routed IP LLC(IPoA) or 2684 Routed IP VC-Mux. You can choose Activated or Deactivated. You can enable or disable the default route. If enable this function, the current PVC will be the default gateway to internet from this device. You can set a tcp mtu value. The range is from 100 to 1500. The default is 1492. Select it to enable Network Address Translation (NAT) function. If you do not select it but want to access the Internet normally, you must add a route on the uplink equipment. Otherwise, the access to the Internet fails. Normally NAT is enabled. Select this option to specify the Routing Information protocol (RIP) version. You can select RIP1, RIP2-B or RIP2-M. You can select None, Both, IN Only or OUT Only to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information then incorporate into routing table. IN only means the ADLS router will only accept but will not send RIP packet. OUT only means the ADLS router will only send but will not accept RIP packet. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL Router supports both IGMP version 1 (IGMP-v1) and IGMP version 2 17 An ISO certified company Default Route TCP MTU Option NAT Dynamic Route Direction Multicast Teracom Limited You may enable or disable MLD Proxy. provided to you by your ISP. subnet mask. If you select Manual mode. IPv6 Prefix Delegation Options for DHCPv6. You can choose DHCP or SLAAC.x. You will need to enter in the Connection type. The Router will not accept the IP address if it is not in this format. which are four IP octets separated by a dot (x.x). DHCP PD Enable MLD Proxy Dual Stack Lite Mode Select Static IP Address in the ISP encapsulation to set static IP information. Provide address assignment to hosts to IPv6 Mode include DHCP in local pools. Teracom Limited 18 An ISO certified company . and gateway address. IP address. Each IP address entered in the fields must be in the appropriate IP form.Select Disabled to disable it. please enter the remote address. You may Enable or Disable the Dual Stack Lite. MLD proxy is enabled only for route mode. You may enable or disable DHCP PD. The ADSL Router support IPv4/v6 Dual Stack Internet Protocol. It works in IPv6 environment.User Manual for TDSL300W2 Field Description (IGMP-v2).x. User Manual for TDSL300W2 Teracom Limited 19 An ISO certified company . 2684 Routed IP LLC(Poi) or 2684 Routed IP VC-Mux. 2684 Bridged IP VC-Mux. Meld proxy MLD Proxy enable. Select Disabled to disable it. which is provided by your ISP. please enter the remote address. Multicast Mode Teracom Limited 20 An ISO certified company . Select it to enable Network Address Translation (NAT) function. You can set a top mute value. IN Only or OUT Only. Both. The ADSL Router supports both IGMP version 1 (IGMP-v1) and IGMP version 2 (IGMP-v2). The range is from 100 to 1500. it is enabled. you must add a route on the uplink equipment. You can select None. The default is 1492. Normally. You can enter the imp address for dial-up. RIP2-B or RIP2-M. You can enter the imp subnet mask for dial-up. If you select Manual mode. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. It works in IPv6 environment. The ADSL Router support IPv4/v6 Dual Stack Internet Protocol. which is provided by your ISP.User Manual for TDSL300W2 The following table describes the parameters of this page: Field Encapsulation Default Route TCP MTU Option Static IP Address IP Subnet Mask Gateway Description You can choose 2684 Bridged IP LLC. If you do not select it but want to access the NAT Internet normally. You can enter the gate way imp for dial-up. the access to the Internet fails. Otherwise. Dynamic Route Direction You can select RIP1. which is provided by your ISP. You can enable or disable default route. only for route mode. Dual Stack Lite You may Enable or Disable the Dual Stack Lite. You may enable or disable MLD Proxy. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Please enter the information accordingly.User Manual for TDSL300W2 Select PPPoA/PPPoE in the ISP encapsulation if your ISP requires you to use a PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Teracom Limited 21 An ISO certified company . This option is typically used for DSL services. User Manual for TDSL300W2 Teracom Limited 22 An ISO certified company . IP Subnet Mask The default is 0. the access to the Internet fails. Dynamic Route You can select RIP1. You can choose Always On (Recommended). Normally. The default is 1400. which Static IP Address is provided by your ISP. You can enter the ip address for dial-up. Both.0. you must NAT add a route on the uplink equipment. The default is multiplay. Get IP Address You can choose Static or Dynamic. The default is 1492. You can set a TCP MTU value. PPPoE VC-Mux. It displays the username for PPPoE dial-up. it is enabled. Select it to enable Network Address Translation (NAT) function. Click it to enable this function to bind the user’s MAC Spoofing computer. Bridge Interface You can choose Activated or Deactivated.0. It displays the password for PPPoE dial-up.0. You can set a tcp mss value. Default Route You can enable or disable default route. The range is TCP MTU Option from 100 to 1500. If you do not select it and you want to access the Internet normally. Username which is provided by your ISP. Encapsulation PPPoA LLC or PPPoA VC-Mux. RIP2-B or RIP2-M. The default is multiplay. You can choose PPPoE LLC. IN Only or OUT Direction Only.User Manual for TDSL300W2 The following table describes the parameters of this page: Field Description Service name You can set the service name. You can select None. IPv6 Mode Provide address assignment to hosts to include Teracom Limited 23 An ISO certified company . Otherwise. The range is from TCP MSS Option 100 to 1452. Connection Connect On-Demand or Connect Manually. You can enter the gateway ip for dial-up. Password which is provided by your ISP. which Gateway is provided by your ISP. Radvd and DHCPv6. DHCP Server. The default IP address is 192. 3. The LAN page that is displayed contains Router Local IP. Teracom Limited 24 An ISO certified company .User Manual for TDSL300W2 Field DHCP PD Enable MLD Proxy Description DHCP in local pools. After finishing. you can change IP address of the router. MLD proxy is enabled only for route mode.168.2 LAN Choose Interface Setup > LAN.1. You may enable or disable DHCP PD. click SAVE to apply the settings of this PVC.3. It works in IPv6 environment. You may enable or disable MLD Proxy. In this page. Choose DHCP or SLAAC. DNS.1. which is the private IP address of the router. IPv6 Prefix Delegation Options for DHCPv6. User Manual for TDSL300W2 Teracom Limited 25 An ISO certified company . It works as igmpSnoop. You may choose Disabled. You can select None. It is an IPv6 MldSnoop multicast constraining mechanism running on Layer 2 devices to manage and control IPv6 multicast groups.255. After Activating IGMP Snoop this function. The starting address of the IP pool 26 An ISO certified company . You can select RIP1. You may select Disabled or Enabled. Enabled or Relay. IN Only or OUT Only. DHCP IP default gateway and DNS Servers to the host under Windows95. You may enter the second IP Address. Both. You can choose Disabled.254.1.User Manual for TDSL300W2 The following table describes the parameters of this page: Field Description Enter the IP address of LAN interface. The default is 259200 seconds. You may select Disabled or Enabled. the packets of the IGMP broadcast will not be sent to the LAN interface not belonging to the group.1 Enter the subnet mask of LAN interface. The range of Main Subnet Mask Alias IP Address Dynamic Route Direction Multicast subnet mask is from 255. It is Main IP Address recommended to use an address from a block reserved for private use. Windows NT and other operation systems that support the DHCP client. IGMP v1 or IGMP v2.0 to 255.255. Second IP Pool Starting IP Address Teracom Limited The second IP address or the second network segment addresses. RIP2-B or RIP2-M. the router can assign IP addresses.255.168. Starting IP Address IP Pool Count Lease Time The starting IP address for the DHCP server's IP assignment The max user pool size The lease time determines the period that the host retains the assigned IP addresses before the IP addresses change. If set to DHCP Server. This CPE Local IP address is 192.255. If you select Auto Discovered. In the DHCP field. Teracom Limited 27 An ISO certified company . Radvd Mode RA Flags Set DHCP6 Server DHCP6 Mode You may choose Auto or Manual. enter the IP addresses of the primary and secondary DNS servers. If select User Discovered. You may choose ManagedAddr or Other Config. the router accepts the firstly-received DNS assignment from one of the PPPoA. This router can also act as a surrogate DHCP server (DHCP proxy) where it relays IP address assignment from an actual DHCP server to clients. The DHCP server can assign IP address. You may choose to Enable or Disable DHCP6 Server. choose Disabled. You may choose to enable or disable Radvd. PPPoE or MER enabled PVC(s) during the connection establishment. You can enable or disable DHCP server or DHCP proxy.User Manual for TDSL300W2 Field IP Pool Count Lease Time DHCP lease time Description The quantity of IP pools You can choose Use Auto Discovered DNS Server Only or Use User Discovered DNS Server Only. Dynamic Host Configuration Protocol (DHCP) allows the individual PC to obtain the TCP/IP configuration from the centralized DHCP server. You can configure this router as a DHCP server or disable it. The Router Advertisement software Daemon product (radvd) that is an open-source implements DNS Relay Radvd Enable link-local advertisements of IPv6 router addresses and IPv6 routing prefixes using the Neighbor Discovery Protocol (NDP). IP default gateway and DNS server to DHCP clients. You may choose Auto or Manual for the DHCP6 Server. the page shown in the following figure appears. choose DHCP Relay.User Manual for TDSL300W2 In the DHCP field. Teracom Limited 28 An ISO certified company . Enter a server IP address running on WAN side. the page shown in the following figure appears. The page as shown in the following figure appears. SSID may be changed or used “BSNL_AP” which is coming in factory settings.3 Wireless Choose Interface Setup > Wireless. User may use any security mode by selecting the “Authentication Mode” to WEP or any other. WPA-PSK/WPA2-PSK Mixed Mode and Wireless MAC Address Filter. 11n Settings.User Manual for TDSL300W2 3. Teracom Limited 29 An ISO certified company . Multiple SSIDs Settings. The Wireless page contains Access Point Settings.3. User needs to enable “Activated” in the Access Point & disable “Deactivated” the Wireless MAC Address filter to use the Wi-Fi Access. Wireless access point of the CPE is coming in deactivated mode & Wireless MAC Address filter is activated in factory mode. allowed users and maximum power levels within these frequency ranges.User Manual for TDSL300W2 The following table describes the parameters of this page: Field Access Point Channel Description You may choose Activated or Deactivated. The Teracom Limited 30 An ISO certified company . Countries apply their own regulations to both the allowable channels. You can set below the control channel or above the control channel. Radius.11g+n or 802. 802. Comply with the IEEE 802. You can set an MCS index between 0 and 7. WEP-64Bits. You can select 802. You may modify the SSID. DTIM range is from 1 to 255. WPA Authentication Type WPA-PSK/ Enterprise. and the wireless client searches the router through broadcasting SSID.11n. Supporting only a root SSID to be modified Select whether the router broadcasts SSID or not.11b+g+n. The service set identification (SSID) is a unique Broadcast SSID SSID name to identify the router in the wireless LAN. WPA2-PSK. You can set a type from Disabled. RTS/CTS Threshold range is from 1500 to 2347. 802. WPA2-PSK. 802. Select No to hide SSID. and the wireless client can not search the SSID. WPA-PSK. 802. Beacon Interval RTS/CTS Threshold Fragmentation Threshold Description Beacon Interval range is from 20 to 1000.11g. You can select Yes or No. Supporting 20MHz/40MHz Dual Channel. A delivery traffic indication message is a kind of traffic indication DTIM message (TIM) which informs the clients of the presence of buffered multicast/broadcast data on the access point.11b. WEP-128Bits. Enterprise.11n Wireless Mode Channel Bandwidth Extension Channel Guard Interval MCS SSID index standards.11b/g and IEEE802. You can set 800 nsec or AUTO.User Manual for TDSL300W2 Field default is Auto. WPA2 Enterprise or WPA/WPA2 Teracom Limited 31 An ISO certified company . or select AUTO. Select Yes.11b+g. Fragmentation Threshold range are only even numbers between 256 and 2346. The page as shown in the following figure The following table describes the parameters of this page: Field 6RD Enable 6rd IPv6 Prefix IPv4 Mask Length 6RD Border Relay Teracom Limited Description You may choose to Enable or Disable 6RD Tunnel function. which can be changed if necessary. The default is 12345678. This function can be used to allow or deny access to certain wireless clients based on their MAC Address. Input 8~63 ASCII characters or 64 hexadecimal characters.User Manual for TDSL300W2 Field Encryption Pre-Shared Key Active Description You may choose TKIP. You can set Allow or Deny to make Wireless LAN station(s) association.4 appears. You can set eight Mac Addresses at most.3. The IP of 6RD Border Relay IPv4Addr is provided 32 An ISO certified company . Choose to activate or deactivate Wireless MAC Address Filter. AES or TKIP/AES. The default is 0. Users can define it. 6RD Choose Interface Setup > 6RD. Action Mac Address #1~8 3. 1 Firewall Choose Advanced Setup > Firewall. SYN Flood. click Advanced Setup. QoS. the page shown in the following figure appears. It displays routing table information. NAT. VLAN and ADSL. IPv4 and mask.4 Advanced Setup In the navigation bar. The page shown in the following figure appears. Port Scan and Land Attack. 3. You can select this option to automatically detect and block Denial of Service (DoS) attacks such as Ping of Death. Teracom Limited 33 An ISO certified company . In the Advanced Setup page that is displayed contains Firewall.User Manual for TDSL300W2 Field IPv4Addr 6rd Delegation Prefix by user’s ISP.4. Description The prefix delegation of 6RD can be used by CPEs in order to receive the prefix.2 Routing Click Advanced Setup > Routing.4. 3. Routing. 3. edit or drop the static route. The metric cost for the destination. Enter the subnet mask of the destination device. This page is used to configure the routing information. This parameter determines if the ADSL router will include the route to this remote node in its RIP broadcasts. If set to Yes. You may add. the page shown in the following figure appears. the route to this remote node 34 An ISO certified company .User Manual for TDSL300W2 Click ADD ROUTE. You can enter the IP address of the next hop in the IP route to the destination device. or bind with a pvc interface. The following table describes the parameters and buttons of this page: Field Destination IP Address IP Subnet Mask Gateway IP Address Metric Announced in RIP Teracom Limited Description Enter the IP address of the destination device. In this page. The page shown in the following figure appears. This field shows the current status of the NAT function for the current VC. you can set up the NAT (Network Address Translation) function for your ADSL router. When you choose Single. You can select Single or Multiple.4.3. If No. The following table describes the parameters and buttons of this page: Field Virtual Circuit NAT Status NAT function. this route is kept private and is not included in RIP broadcasts. NAT is short for Network Address Translation.User Manual for TDSL300W2 Field Description will be propagated to other hosts through RIP broadcasts. you should activate NAT function for a virtual circuit. This field is to specify how many IPs are provided by Number of IPs your ISP for current VC. The Network Address Translation Settings window allows you to share one WAN IP address for multiple computers on your LAN. you can set DMZ Teracom Limited 35 An ISO certified company Description Enter Virtual Circuit Index that you plan to setup for the .3 NAT Choose Advanced Setup > NAT.1 Internet. Beforehand. Please refer to 3. 3. for VCs with single IP. such as web (HTTP) servers. Teracom Limited 36 An ISO certified company . In the NAT page. Demilitarized Zone (DMZ) is used to provide Internet services without sacrificing unauthorized access to its local private network. for VCs with multiple IPs. and the page shown in the following figure appears. Note: For VCs with single IP. for VCs with multiple IPs. the DMZ host contains devices accessible to Internet traffic. Typically. Virtual Server or IP Address Mapping (for Multiple IP Service). FTP servers. The following table describes the parameters of this page: Field DMZ DMZ Host IP Address Description Select Enable DMZ to enable this function. In the NAT page. Furthermore. Enter the specified IP Address for DMZ host on the LAN side. they share the same DMZ and Virtual servers.User Manual for TDSL300W2 Field Description or Virtual Server. When you choose Multiple. they can define the Address Mapping rules. SMTP (e-mail) servers and DNS servers. each VC can set DMZ and Virtual servers. choose Virtual Server. and the page shown in the following figure appears. there is no need to individually define the Address Mapping rule. choose DMZ. since they have only one IP. You can set DMZ. You can enter an application name. You can specify 10 rules in maximum.User Manual for TDSL300W2 The Virtual Server is the server or server(s) behind NAT (on the LAN). The following table describes the parameters of this page: Field Rule Index Application Teracom Limited Description The Virtual server rule index for this VC. All the VCs with single IP will use the same Virtual Server rules. that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. or select a name 37 An ISO certified company . Web server or FTP server. for example. you can set the start and end port number to 21. Teracom Limited 38 An ISO certified company . You can choose ALL. and the page shown in the following figure appears. you can enter the End port number the same as Start port number. if you want to set the FTP Virtual server. If it is one port only. select Number of IPs as Multiple. For example. The IP Address Mapping rule is per-VC based (only for Multiple IPs' VCs). TCP or UDP. Choose the transport layer protocol that the service type. Enter the IP Address for the Virtual Server in LAN side. Enter the specific Start and End Port number you want to forward. and then choose IP Address Mapping (for Multiple IP Service).User Manual for TDSL300W2 Field Description from the right drop-list menu like FTP or TELNET. Protocol Start/End Port Number Local IP Address In the NAT page. so that one packet whose source IP is in range of the specified address will select one IP address from the pool for NAT.0 and the End IP is 255. Many-to-Many No Overload. the page shown in the following figure appears.4 QoS Choose Advanced Setup > QoS. Local Local Start/End IP Start IP is the starting local IP address and Local End IP is the ending local IP address.0.0. Rule Type Many-to-Many Overload.0. or Server.255.4. This option provides better service of selected network traffic over various technologies. If the rule is for all local IPs. Public Public Start/End IP Start IP is the starting public IP address and Public End IP is the ending public IP address.255. enter 0. Enter the public IP Address you want to do NAT. If you have a dynamic IP. 3.User Manual for TDSL300W2 Entries in this table allow you to configure one IP pool for specified source IP address from LAN. then the Start IP is 0. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules. Teracom Limited 39 An ISO certified company . The following table describes the parameters of this page: Field Rule Index Description The Virtual server rule index for this VC. The QoS can be set based on the physical LAN ports or wireless interfaces. Many-to-One.0. Enter the local IP Address you plan to mapped to.0 as the Public Start IP. Choose the One-to-One.255. User Manual for TDSL300W2 Teracom Limited 40 An ISO certified company . 323. You may select None. You may select Activated or Deactivated. The destination IP address of the rule. Application Physical Ports Destination MAC H. SIP. After QoS activating QoS. DNS. IPv4 is Click the QoS Settings Summary button to view the table of Qos rules and actions.User Manual for TDSL300W2 The following table describes the parameters of this page: Field IP Version selected. Teracom Limited 41 An ISO certified company Description You may select IPv4 or IPv6. WFQ. If data packets include the MAC address. DHCP. MGCP. Choose an Ethernet interface or WLAN Interface. If data packets IP Port Range Source MAC include the IP address. You may select Activated or Deactivated. WRR or RED. Port Range is from 0 to 65535. AF-PHB or EF-PHB. Set the weight of EF-PHB . The QoS rule can be set if it is activated. the data packets are placed into the group. The Destination MAC address of the rule. Set the percents of each priority. the data packets are placed into the group. Summary PHB QoS Discipline Queue Bandwidth Priority Weight EF-PHB Priority Weight Rule Index Active You may establish at most 12 QoS rules. The Source MAC address of the rule. you may set the upload bandwidth of the WAN interface. SNMP. Set the weight of each priority. RIP. the data packets are placed into the group. Support application options such as IGMP. If data packets include the MAC address. In this figure. RSTP. RTCP and RTP. You may select Strict Priority. 1p Queue # Teracom Limited Select Low.094. Five and six are often for delay-sensitive applications such as interactive video and voice.1p. so the maximum possible VLAN configurations are 4. VID (VLAN ID) is the identification of the VLAN.down to "loss eligible" traffic. It has 12 bits and allows the identification of 4096 (2^12) VLANs.1Q. you need to enter an IP precedence range. Maximize throughput. Select this option to Activate/Deactivated the 802. Maximize reliability and Minimize monetary cost. Zero is used as a best-effort default priority. Minimize delay. which is basically used by the standard 802. 802. DSCP Range is from 0 to 63.User Manual for TDSL300W2 Field Protocol ID IGMP. Although network managers must determine actual mappings. Data classes four through one range from controlled-load applications such as streaming multimedia and business-critical traffic carrying SAP data. Medium. for instance . UDP. ICMP or Select this option to Activated/Deactivated the 4094 VID on the 4 different queues. a VID of 0 is used to identify priority frames and value 4095 (FFF) is reserved. TCP. High or Highest. Seven is the highest priority which is usually assigned to network-critical traffic such as Routing Information Protocol (RIP) and Open Shortest Path First (OSPF) table updates.1p establishes eight levels of priority (0 ~ 7). Support services including Normal service. Vlan ID Range IPP/DS Field IP Precedence Range Type of Service DSCP Range You may set IPP/TOS or DSCP. When IPP/DS field is set to IPP/TOS. Description You can choose TCP/UDP. IEEE 802. IEEE has made broad recommendations. 42 An ISO certified company . invoked automatically when no other value has been set. Of the 4096 possible VIDs. and the page shown in the following figure appears. Source IPv6 and DSCP Range.User Manual for TDSL300W2 In the above figure. Click Save at the bottom of the page to save the discipline. You may set the parameters by referring to those in the above figures. To view the rules and actions. Enter a destination IPv6. click QoS Settings Summary to enter the page shown in the following figure appears. Teracom Limited 43 An ISO certified company . choose the IP Version as IPv6. User Manual for TDSL300W2 3. bandwidth allocation and resource optimization. when in fact they are located on a number of different LAN segments. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire. Because VLANs are based on logical instead of physical connections. and the page shown in the following figure appears. choose Activated and then Assign VLAN PVID for each Interface.5 VLAN Choose Advanced Setup > VLAN.4. it is very flexible for user/host management. the page shown in the following figure appears. Teracom Limited 44 An ISO certified company . In the VLAN page. 45 An ISO certified company . PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. You can set a PVID for an ATM VC. The Ethernet port can be tagged. Choose to active or deactive the current vlan settings. choose Activated and then Define VLAN Group. Supporting eights ATM VCs. Ethernet port or Wireless LAN. which can be tagged. and the page shown in the following figure appears. VLAN ID is from 1 to 4094. In the VLAN page.User Manual for TDSL300W2 Each physical port has a default VID called PVID (Port VID). The Wireless LAN port can be tagged. The following table describes the parameters of this page: Field VLAN Index Active VLAN ID ATM VCs Ethernet Wireless LAN Teracom Limited Description Choose a vlan index from 1 to 8. Teracom Limited 46 An ISO certified company . G. DDNS and CWMP. ADSL2. ADSL2.User Manual for TDSL300W2 3. The ADSL feature can be selected when you meet the physical connection problem. Choose ANNEX A.DMT. Click here to enable SRA function. Filter.5 Access Management In the navigation bar.DMT. T1. The Access Management page that is displayed contains ACL. the page shown in the following figure appears. 3. G. The router supports these modulations: G.4.413. click Access Management. T1.6 ADSL Click Advanced Setup > ADSL. ANNEX I.lite. Please check the proper settings with your Internet service provider. ADSL2+ and Auto-Syno Up. ANNEX M or ANNEX A/I/J/L/M. Click here to enable Bitswap function. ADSL2+. UPnP.lite. The following table describes the parameters and buttons of this page: Field ADSL Mode ADSL Type Bitswap Enable SRA Enable Description Choose Auto Sync-Up. The router negotiates the modulation modes with the DSLAM. The default is Auto Sync-Up. ANNEX A/L.413 or G. 5. LAN or Both. SNMP. Telnet. The rule is valid if the IP is in this range. Select IP/MAC Filter type. and the page shown in the following figure appears.0. With the default IP 0.0.User Manual for TDSL300W2 3.1 ACL Choose Access Management > ACL. Application Filter or URL Filter. Ping or ALL. Click to enable or disable the rule.5. and the page shown in the following figure appears. The user may remotely access the ADSL Router once setting his IP as a Secure IP Address through selected applications. The user can set IP/MAC Filter. Only the devices whose MAC addresses are listed in the Access Control Listing can access the router. FTP.0. Support WAN. any client would be allowed to remotely access the ADSL Router. The following table describes the parameters and buttons of this page: Field ACL Rule Index Active Secure IP Address Application Interface Access control Listing Support Web. 3. Teracom Limited 47 An ISO certified company . Description You can establish sixteen ACL rules at most.2 Filter Choose Access Management > Filter. 48 An ISO certified company . UDP or ICMP) and a specific direction (incoming.1 IP/MAC Filter Choose Access Management > Filter > Filter Type > IP/MAC Filter.User Manual for TDSL300W2 3.2. The following table describes the parameters and buttons of this page: Field Filter Type Selection Teracom Limited Description Support IP / MAC Filter. The user can set different IP filter rules of a given protocol (TCP.5. Application Filter and URL Filter. and the page shown in the following figure appears. outgoing. or both) to filter the packets. 0. Choose Both.0.0 means Don't care. Support TCP. YMSG.0. Enter the Port Number. and the page shown in the following figure appears. The user can set Application rules to filter the ICQ. Support IP or MAC. Description You can choose an IP / MAC Filter Set Index from 1 to You can select an interface from the eight pvcs or the lan interface.2 Application Filter Choose Access Management > Filter > Filter Type> Application Filter.0. Select Application Filter type. 3.0.2. Enter the Source IP Address. Real Audio/Video packets. Enter the Destination IP Address. Incoming or Outgoing. 0 means don't care.5. UDP or ICMP. 0.User Manual for TDSL300W2 Field IP/MAC Filter Set Index Interface Direction Rule Type Source IP Address Port Number Destination IP Address Protocol 12. Teracom Limited 49 An ISO certified company .0 means don't care. MSN. Description Choose to activate or deactivate the Application Filter 3. Set Allow or Deny ICQ packets. Set Allow or Deny Real Audio/Video packets.2. Teracom Limited 50 An ISO certified company .3 URL Filter Choose Access Management > Filter > Filter Type>URL Filter. Set Allow or Deny YMSG packets. The user can set URL rules to prevent the LAN users to access.User Manual for TDSL300W2 The following table describes the parameters and buttons of this page: Field Application Filter ICQ MSN YMSG Real Audio/Video rule. Select URL Filter type.5. Set Allow or Deny MSN packets. and the page shown in the following figure appears. Can set an URL Filter Index fro m 1 to 16. obtain an IP address. Enter the URL that needs to be filtered. a device can leave a network smoothly and automatically when it is no longer in use. Teracom Limited 51 An ISO certified company . In turn.5. An UPnP device can dynamically join a network. The following table describes the parameters of this page: Field UPnP Auto-configured Description You can choose Activated or Deactivated.3 UPnP Choose Access Management > UPnP. UPnP (Universal Plug and Play) is a distributed. open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. This page is used to configure the upnp parameters. the page shown in the following figure appears.User Manual for TDSL300W2 The following table describes the parameters and buttons of this page: Field Active URL Index URL Description Make URL Filter rule activated or deactivated. convey its capabilities and learn about other devices on the network. UPnP broadcasts are only allowed on the LAN. UPnP network devices can automatically configure network addressing. announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. 3. 5. User should type the host name.User Manual for TDSL300W2 3. the page shown in the following figure appears. The Dynamic Domain Name System (DDNS) lets you use a static host name with a dynamic IP address.4 DDNS Choose Access Management > DDNS. The following table describes the parameters of this page: Field Dynamic DNS My Host Name E-mail Address Username Password Wildcard support The DDNS identifier The email provided by DDNS provider The name provided by DDNS provider The password provided by DDNS provider You can choose Yes or No. user name and password assigned to your ADSL Router by your Dynamic DNS provider. 3. and the page shown in the following figure appears. Description Choose to activate or deactivate DDNS function.5.5 CWMP Choose Access Management > CWMP. Teracom Limited 52 An ISO certified company . the connection password provided by TR-069 service for a connection request to the CPE. Select Activated to periodically connect to the ACS to check for configuration updates. This parameter must be in the form of a valid http or https url. User Name Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. 53 An ISO certified company . Password Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. UserName Password Periodic Inform Interval(s) Teracom Limited CPE’s username. the connection username provided by TR-069 service CPE’s password. Specify the duration between two connections to ACS.User Manual for TDSL300W2 The following table describes the parameters of this page: Field URL Description URL for the CPE to connect to the ACS using the CPE WAN Management Protocol. Enter the new password again. click Maintenance.2 Time Zone Choose Maintenance > Time Zone. The Maintenance page that is displayed contains Administration. 3. the page shown in the following figure appears. the page shown in the following figure appears. Admin has read/write access privilege.1 Administration Choose Maintenance > Administration. The system time is the time used by the device for scheduling services.6 Maintenance In the navigation bar.6. You can manually set the time or connect to a NTP (Network Time Protocol) server. you will only need to set the time zone. Teracom Limited 54 An ISO certified company .6. Time Zone. There is only one account that can access Web-Management interface.User Manual for TDSL300W2 3. The default account is "admin". Firmware. In this web page. Description Enter the password to which you want to change the 3. The following table describes the parameters of this page: Field New Password Confirm Password old password. you can set new password for admin. If a NTP server is set. and the password is "admin". SysRestart and Diagnostics. If you manually set the time. Set the NTP server manually. Choose the time zone in which area you are from the drop-down list.6.3 Firmware Choose Maintenance > Firmware. Teracom Limited 55 An ISO certified company . You can upgrade the firmware of the Router in this page. PC’s Clock 3. Description You can choose NTP Server automatically. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to browse the local hard drive and locate the firmware to be used for upgrade. You can enable the daylight saving time. The following table describes the parameters of this page: Field Synchronize time with Time Zone Daylight Saving NTP Server Address or Manually. the page shown in the following figure appears.User Manual for TDSL300W2 you may also set Daylight Saving dates and the system time will automatically adjust on those dates. Then you can save the configuration file of the router. After selecting the file.4 SysRestart Choose Maintenance > SysRestart. Description Click Browse to select the firmware file. Teracom Limited 56 An ISO certified company .User Manual for TDSL300W2 The following table describes the parameters of this page: Field New Firmware Location New Romfile Location Romfile Backup UPGRADE Click it. the page shown in the following figure appears. 3. and select the path. User can restart the device with current settings or factory default settings. Click Browse to select the Rom configuration File. click UPGRADE to starting upgrading the file.6. 5 Diagnostics Choose Maintenance > Diagnostics.User Manual for TDSL300W2 The following table describes the parameters of this page: Field Current Settings Factory Default Settings Description Save the current settings and then reboot the router. 3. The following table describes the parameters of this page: Field Virtual Circuit Description Choose a PVC from the drop down list to test. Teracom Limited 57 An ISO certified company . The page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. the page shown in the following figure appears. Reset to the factory default settings and then reboot the router.6. User Manual for TDSL300W2 Teracom Limited 58 An ISO certified company .