Technical Bulletin0199-27-1215/0 EN This Circular supersedes: Date: Author: Phone: Fax: 10.09.2010 Rudolf Fischer, VE-FI +49 (0) 221 822-3008 +49 (0) 221 822-15 3008 DEUTZ AG Ottostraße 1 51149 Köln www.deutz.com Important safety advice EMR2 Safety-Update 1 2 3 EMR2-Safety-Update can be done with DEUTZ-Servicetool SerDia2000 Version 1.5.6 and Interface-Level 3 (plus Password) or with Level 3A. The password for Level 3 can be requested via emailadress
[email protected] . Send the serialnumber of your interface box in the email. EMR2-Safety-Update, SerDia2000-Software and SerDia-Handbook are available on the following internet-link http://207.37.9.103/Service/Technik/Servicedoku/sis_publ.nsf/gestaltungsdokumente/ serdia/ 4 The related EMR2-Safety-Update for the different EMR2-Software-Variants is displayed in the following table. The defined assignment must be considered strictly. OLD EMR2-ECU Software (BSW) 1 2 3 4 5 2.XX, 2.05, 2.06, 2.08 3.XX, 3.01, 3.04, 3.11 4.XX, 4.02, 4.04, 4.05 7.XX, 7.00, 7.01, 7.02 9.XX NEW Update 2.09 3.12 4.07 7.05 9.01 1015 / 2012 / 2013 2012 / 2013 2012 / 2013 2011 / 2012 / 2013 914 / 2012 / 2013 Engine type Note: The part numbers indicated in this document are not subject to updating. Binding for the identification of spare parts is exclusively the spare parts documentation. OBJ_DOKU-23022-001.fm 1/4 © 2010 engine operating hours and software version of the new software. Please consider the naming of the datasets shown below.1 ECU-programming Download the "old" saved dataset back to the ECU by using SerDia-Menu overall programming Switch OFF and Switch ON the ECU (ignition OFF-ON) Upload the engine dataset by using SerDia-Menu overall programming and save it on the harddisk (path C:\Temp\EMR2\NewDataset) Erase errormemory 1 and 2 Check logistic data. Download the corresponding EMR2-Safety-Update into ECU..Technical Bulletin 0199-27-1215/0 EN 5 Prior programming the engine-dataset has to be saved on harddisk first. Create a folder for your datasets please. if one of the above named EMR2-ECU-Software versions is present on the ECU. such as engine serial no.1. Example: – – – C:\Temp\EMR2\OldDataset C:\Temp\EMR2\NewDataset C:\Temp\EMR2\NewBSW 6 Description of the job • • • Switch ON the ECU. connect the diagnosis devices (check Ubatt-lamp of the interface box) and start the SerDia2000-program.1. First save the dataset on harddisk (path C:\Temp\EMR2\OldDataset) by using SerDia-Menu overall programming.5. Check. • • • • • • OBJ_DOKU-23022-001.fm 2/4 © 2010 . "How to do…" see SerDia-manual chapter 6. hex with jjmmtt = Tag des Updates = 100913 and sssssss und mmmmmmmm see picture sssssssss = ECU-SerialNo = 2124304 mmmmmmm = engineNo = 10748335 OBJ_DOKU-23022-001.hex have to be sent back to emailadress
[email protected] .hex Example: 10748335_2124304_100913_new.Technical Bulletin 0199-27-1215/0 EN 7 8 Uploaded engine datasets mmmmmmm_sssssss_jjmmtt_new. Naming of datasets mmmmmmmm_sssssss_jjmmtt_new.hex und mmmmmmmm_sssssss_jjmmtt_old.fm 3/4 © 2010 . com Service Information This document has been created digitally and is valid without a signature. You will find the new DEUTZ-PartNo in SERDIA.fm 4/4 © 2010 . OBJ_DOKU-23022-001.com. near to the ECU or near to the diagnostic plug. see picture. PartNo for Label Contact: DEUTZ Engines E-mail:
[email protected] Bulletin 0199-27-1215/0 EN 9 Because of the homologation of the engine you must put a sticker (label) with the new DEUTZ-PartNo on the ECU. The sticker must be orderd via E-mail emr2@deutz.