Toshiba

FILE NO.140-200601GR (MFR’S VERSION A) SERVICE MANUAL COLOR TELEVISION/ DVD VIDEO PLAYER MD20Q42 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2). For (*1) and (*2), see the next page. DOCUMENT CREATED IN JAPAN, January, 2006 GREEN (*1) GREEN PRODUCT PROCUREMENT The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts. Green procurement of parts is not only confined to manufacture. The same green parts used in manufacture must also be used as replacement parts. (*2) LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING This product is manufactured using lead free solder. DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT ! The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F (30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product made with lead-free solder may result in damage to the component and or PCB being soldered. Great care should be made to ensure high-quality soldering when servicing this product  especially when soldering large components, through-hole pins, and on PCBs  as the level of heat required to melt lead-free solder is high. A1-1 CAUTION THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM. Location of the required Marking The rating sheet and the safety caution are on the rear of the unit. CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. PREPARATION OF SERVICING The laser diode used for a pickup head may be destroyed with external static electricity. Moreover, even if it is operating normally after repair, when static electricity discharge is received at the time of repair, the life of the product may be shortened. Please perform the following measure against static electricity, be careful of destruction of a laser diode at the time of repair. • Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. A1-2 etc. [Note 1] In the condition that an explosion-proof cathoderay tube is set in this equipment. (Particularly the VERSION LETTER. AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Take enough care to deal with it. Remove the antenna terminal on TV and turn on the TV. 5. [Note 2] External exposure metal: Antenna terminal HOW TO ORDER PARTS Please include the following informations when you order parts. KEEP THE NOTICES 6. 2. A1-3 . 2. they are indicated with the labels or seals on the cabinet. when repairing the high voltage peripheral circuit. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. Therefore. the inspection repair should be required. chassis and parts. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. 7. Repairing except indicates causes rising of high voltage. PART NO. the designated parts must be used. Make sure to keep the indications and notices in the operation manual. or which are assembled in the condition that these do not contact with the printed board. 3. parts and wiring which were removed in order to service are put in the original positions. Avoid an electric shock while the electric current is flowing. 4. the part which is replaced should be used the part which has the same character. or whether there are the portions which are deteriorated around the serviced places serviced or not. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE 1.SERVICING NOTICES ON CHECKING 1. If the insulation resistance is less than 1M ohm. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. Therefore. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. it is dangerous to give a shock. AVOID AN X-RAY As for the places which need special attentions. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark. And be sure the safety of that. (INSULATION CHECK PROCEDURE) There are parts which use the insulation material such as a tube or tape for safety. If you have not the 500V insulation resistance meter. put these parts in the original positions. PERFORM A SAFETY CHECK AFTER SERVICING Confirm that the screws. and it emits an X-ray from the cathoderay tube. when removing it or serving from backward. 3. 2. USE THE DESIGNATED PARTS The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore.) 1. use a Tester. Unplug the plug from the AC outlet. use the designated parts and make sure not modify the circuit. safety is secured against implosion. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit. and DESCRIPTION You can find it in your SERVICE MANUAL. 4. However. contact your electrician to replace your obsolete outlet. 13. This plug will fit into the power outlet only one way. This unit should never be placed near or over a radiator or heat source. If you are unable to insert the plug into the outlet. 2. For units intended to operate from battery power. POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. consult your appliance dealer or local power company. If the plug should still fail to fit. 11. CLEANING Unplug this unit from the wall outlet before cleaning. in a wet basement. refer to the operating instructions.IMPORTANT SAFEGUARDS 1. A1-4 . bracket. The unit may fall. Do not use liquid cleaners or aerosol cleaners. convenience receptacles. 9. kitchen sink. When installing an outside antenna system. 7. to ensure reliable operation of the unit. This is a safety feature. sofa. GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). contact your electrician to replace your obsolete outlet. These openings must not be blocked or covered. is a safety feature. near a bathtub. causing serious injury. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. stand. a plug having a third (grounding) pin. 4. OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit. 5. or table. The openings should never be blocked by placing the unit on a bed. LIGHTNING To protect your unit from a lightning storm. 14. as this can result in a risk of fire or electric shock. and serious damage to the unit. this plug will only fit into a grounding-type power outlet. For example. or laundry tub. 8. and the point where they exit from the appliance. 15. If your unit is equipped with a 3-wire grounding-type plug. or near a swimming pool. bracket. tripod. unplug it from the wall outlet and disconnect the antenna or cable system. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. An appliance and cart combination should be moved with care. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits. Do not defeat the safety purpose of the grounding-type plug. rug. and to protect it from overheating. If you are not sure of the type of power supply to your home. 3. or where it can fall into such power lines or circuits. tripod. 6. Quick stops. This will prevent damage to the unit due to lightning and power line surges. as contact with them might be fatal. 16. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. Use only with a cart. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. paying particular attention to cords at plugs. and uneven surfaces may cause the appliance and cart combination to overturn. try reversing the plug. Never spill or spray any type of liquid into the unit. 8A. 10. or other sources. S3126A VENTILATION Slots and openings in the cabinet and in the back or bottom are provided for ventilation. stand. PORTABLE CART WARNING ACCESSORIES (symbol provided by RETAC) Do not place this unit on an unstable cart. excessive force. Do not defeat the safety purpose of the polarized plug. If you are unable to insert the plug fully into the outlet. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. Use a damp cloth for cleaning. as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. This too. POWER SOURCES This unit should be operated only from the type of power source indicated on the rating plate. ATTACHMENTS Do not use attachments not recommended by the unit’s manufacturer as they may cause hazards. 12. OVERLOADING Do not overload wall outlets and extension cords. washbowl. extreme care should be taken to keep from touching such power lines or circuits. WATER AND MOISTURE Do not use this unit near water. or other similar surface. or when it is left unattended and unused for long periods of time. or table recommended by the manufacturer. 20. size of grounding conductors. b. deformed. this indicates a need for service. keep the volume at a moderate level. If the unit has been dropped or the cabinet has been damaged. 18. REPLACEMENT PARTS When replacement parts are required. be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. WALL OR CEILING MOUNTING The product should be mounted to a wall or ceiling only as recommended by the manufacturer. DISC Do not use a cracked. specifies that the cable ground shall be connected to the grounding system of the building. f. heat registers. Unauthorized substitutions may result in fire. 24. or repaired disc. LASER BEAM Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. CONNECTING When you connect the product to other equipment. Otherwise. HEADPHONES When you use the headphones. sudden high volume sound may cause hearing or speaker damage. in particular. When the power-supply cord or plug is damaged. it may cause hearing damage. and requirements for the grounding electrode. provides information with respect to proper grounding of the mast and supporting structure. If you use the headphones continuously with high volume sound. DISC TRAY Keep your fingers well clear of the disc tray as it is closing. 28. turn off the power and unplug all of the equipment from the wall outlet. SOUND DISTORTION Do not allow the product output distorted sound for a longtime. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections. be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 26. 23. It may cause speaker overheating and fire. location of antenna discharge unit. 30. These discs are easily broken and may cause serious personal injury and product malfunction. as close to the point of cable entry as practical. 19. 22. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and. or other products (including amplifiers) that produce heat. 25. If the unit has been exposed to rain or water. as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. HEAT The product should be situated away from heat sources such as radiators. or objects have fallen into the unit. 21. SAFETY CHECK Upon completion of any service or repairs to this unit. If liquid has been spilled. When the unit exhibits a distinct change in performance. SOUND VOLUME Reduce the volume to the minimum level before you turn on the product. It may cause sight damage. c. stoves. electric shock or other hazards. Section 810 of the National Electrical Code. grounding of the lead-in wire to an antenna discharge unit. d. 27. ANSI/NFPA 70. Adjust only those controls that are covered by the operating instructions.IMPORTANT SAFEGUARDS (CONTINUED) 17. It may cause serious personal injury. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit. A1-5 . 29. If the unit does not operate normally by following the operating instructions. DAMAGE REQUIRING SERVICE Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. e. Failure to do so may cause an electric shock and serious personal injury. 31. connection to grounding electrodes. Refer all servicing to qualified service personnel. PART H) NEC-NATIONAL ELECTRICAL CODE S2898A A1-6 .IMPORTANT SAFEGUARDS (CONTINUED) EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. Pick Up PCB Short circuit using a soldering iron. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector. (Refer to Fig. the Laser may be damaged. • Use the Lead Free solder. Fig. Manually open the Tray.0Ag-0. 1 DISC REMOVAL METHOD AT NO POWER SUPPLY 1. 1) 3. NOTE • Before your operation. • Manual soldering conditions • Soldering temperature: 350 ± 5˚C • Soldering time: Within 2 seconds • Soldering combination: Sn-3. Rotate the Main Gear in the direction of the arrow by hand. please read “PREPARATION OF SERVICING”. Main Gear Deck CD Fig. the short circuit the position shown in Fig. Remove the Back Cabinet and AV PCB/DVD Block. 1 using a soldering iron.5Cu • When Soldering/Removing of solder. 1 A1-7 .WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD PCB connector. use the draw in equipment over the Pick Up Unit to keep the Flux smoke away from it. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS. If you remove the DVD Deck with no soldering.) 2. 3. 4. please follow the steps below. 7. please follow the steps below. 4. NOTE: No indications on the screen when the Tray Lock is setting. 1. Simultaneously press and hold the '9' key on the remote control unit. 2. To unlock the Tray Lock. please follow the steps below. Set the DVD to the Stop Mode. 3. Hold both keys for more than 3 seconds. NOTE: No indications on the screen when the Tray Lock is setting. Tray cannot be opened by setting the Tray Lock. Press and hold the '7' key on the remote control unit. Set the DVD to the Stop Mode. To unlock the Tray Lock. The Tray Lock has now been cleared. Simultaneously press and hold the 'STOP' key on the front panel. Turn Unit ON. NOTE: No indications on the screen when the Tray Lock is setting. 1. 4. Turn Unit ON. 3. Confirm that the 'No Disc' will be appeared on the screen. The Tray Lock has now been cleared. A1-8 . 'SUBTITLE'. The Tray Lock has now been set up. 4.PARENTAL CONTROL . Turn Unit ON. 3. 4. The On Screen Display message ' ' will appear. Set the DVD to the Stop Mode. please follow the steps below. The Tray Lock has now been set up. '3'. 5. Press it in order of 'SETUP'. 'AUDIO SELECT' and '0' key of a remote control unit.RATING LEVEL 4 DIGIT PASSWORD CANCELLATION If the stored 4 digit password in the Rating Level menu needs to be cancelled. 1. The On Screen Display message ' ' will appear. 5. 8. Press it in order of 'SETUP'. 7. 5. '3'. Turn Unit ON. 2. The On Screen Display message ' ' will appear. 3. 2. 6. 1. 2. NOTE: No indications on the screen when the Tray Lock is setting. The On Screen Display message 'PASSWORD CLEAR' will appear. please follow the steps below. It is likely to be going to be changed to the following steps without a previous notice in the future. Press and hold the 'STOP' key on the front panel. please follow the steps below. Set the DVD Mode. 'AUDIO SELECT' and '0' key of a remote control unit. 6. 1. 5. 7. 6. Press and hold the 'STOP' key on the front panel. The On Screen Display message ' ' will appear. If the above is not effective measures. 2. Hold both keys for more than 3 seconds. The 4 digit password has now been cleared TRAY LOCK Tray cannot be opened by setting the Tray Lock. Set the DVD to the Stop Mode. Turn Unit ON. 5. 'SUBTITLE'. Hold both keys for more than 3 seconds. Simultaneously press and hold the '9' key on the remote control unit. ............................................... DISC REMOVAL METHOD AT NO POWER SUPPLY .............. POWER ...................................................................................................... F-8 G-1...................... B1-2 B2-1~B2-4 B3-1 B4-1.......................................................................................................................................................................................... B4-2 C-1 C-1..............TABLE OF CONTENTS GREEN PRODUCT PROCUREMENT ............................................................................................................ BLOCK DIAGRAMS DVD ... CAUTION ................................................................. SERVICE MODE LIST ................................................................... G-4 G-5..................................................... E-2 E-3................................................... C-2 D-1~D-6 E-1............................... IMPORTANT SAFEGUARDS ................. AV/CRT ........................................................................................ POWER .. MECHANICAL REPLACEMENT PARTS LIST ................................................................................. E-4 E-5.................................................. PRINTED CIRCUIT BOARDS DVD . G-10 G-11............................................................................................... G-14 G-15....................................................................................................... PARENTAL CONTROL-RATING LEVEL .. G-16 G-17.............................................. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................................................................................. IN/OUT ........................................................................................................ WHEN REPLACING EEPROM (MEMORY) IC ................................................................................................................................................................... G-18 G-19......................................... DEFLECTION ...................................................................................................................... DISASSEMBLY INSTRUCTIONS 1...................................................... MOTOR DRIVE ............ TABLE OF CONTENTS ................................................. REMOVAL OF MECHANICAL PARTS AND P................................................................................................................................................................................................ REMOVAL OF DVD DECK PARTS ........................ COMB/FILTER ........................................................................................................... A2-1 A1-1 A1-1 A1-2 A1-3 A1-3 A1-4~A1-6 A1-7 A1-7 A1-8 A1-8 A2-1 A3-1~A3-6 B1-1......................................................... G-8 G-9........................................... SOUND AMP ....................................................................................................................................................................................................................................... REGULATOR ............................................. G-22 G-23................................................. ELECTRICAL ADJUSTMENTS .......................................................... TRAY LOCK ............................. TV ....................................................................... C.......... LOADING MOTOR/SW .......... G-26 G-27...... G-6 G-7....................................................... ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................... G-30 H-1~H-3 I1-1~I1-3 I2-1 J1-1 J2-1 J3-1~J3-4 ........................... WAVEFORMS .............................................................................. MICON/TUNER ............................ AUDIO/VIDEO ........................................................................................................................... G-28 G-29............................................................................................................................... DVD DECK REPLACEMENT PARTS LIST ................................................................ MECHANICAL EXPLODED VIEWS ....................................................... SERVICING NOTICES ON CHECKING ......................................... GENERAL SPECIFICATIONS ......................................... DVD DECK EXPLODED VIEW ...................................................................................................................... HOW TO ORDER PARTS ..................................................................................... E-6 F-1.................................................................. G-12 G-13................................... LEAD-FREE SOLDER ........ G-2 G-3................... G-20 G-21. F-2 F-3~F-6 F-7............................................................. G-24 G-25.. 2............................................................................................................................... LOADING MOTOR/SW ............................................................................................... WHEN REPLACING DVD DECK .................................................................................................................................................................................................. 4.......................................................................... REMOVAL OF ANODE CAP ......................................... 3............................................................................................. BOARDS ............................................................... INTERCONNECTION DIAGRAM ............................... CHROMA .... SCHEMATIC DIAGRAMS MPEG/MICON/DSP ......................... CRT ... MEMORY ......................................................................................................................................................................................................................... A-5~A-1.0W + 1. J~W.45G / 0.75MHz 41.0dBm/50k ohm -0.kWh/Year Yes Yes No No UL FCC DHHS DHHS +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH . 80 mm DM3SA 4 step 2-120 times(DVD.0 mmV Normal +0.0W Color System Speaker Sound Output G-2 DVD System Position Size Impedance Max 10%(Typical) Color System Disc Disc Diameter Drive Search speed Fwd Actual Rev Actual Slow speed Actual Actual G-3 Tuning System Broadcasting System Tuner and Receive CH Intermediate Frequency G-4 Signal Preset CH Stereo/Dual TV Sound Tuner Sound Muting Video Signal RGB Signal Audio Signal G-5 Power Power Source Power Consumption Protector G-6 Regulation G-7 Temperature G-8 Operating Humidity System Destination CH Coverage Picture(FP) Sound(FS) FP-FS Input Level Output Level S/N Ratio (Weighted) Horizontal Resolution at DVD Mode Output Level Input Level Output Level Digital Output Level S/N Ratio at DVD (Weighted) Harmonic Distortion Frequency Response : at DVD at Video CD at SVCD at CD AC DC at AC at DC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Dew Sensor Safety Radiation X-Radiation Laser Operation Storage A3-1 NTSC DVD. CD-R/RW.18G NTSC 2 Speaker Front 3 inch 8 ohm 1. 4A. CD-DA.GENERAL SPECIFICATIONS G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 20 inch / 508. A~I. VIDEO CD) 4-40 times (CD) 4 step 2-120 times(DVD.50MHz No No Yes 1 V p-p/75 ohm ------8.5 V p-p/75 ohm ------120V.25MHz 4. VIDEO CD) 4-40 times (CD) Fwd 1/7 . W+1~W+84 45. Video CD DVD-R/RW (Video Format Only) 120 mm . 60Hz -90W at 120V 60Hz -5W at 120V 60Hz -.1/2 times -Rev --US System M 1Tuner US(w/CABLE) 2~69. GENERAL SPECIFICATIONS G-9 On Screen Display Menu(TV) Menu Type TV Setup Picture Audio Picture Preference Channel Setup TV/CABLE Auto CH Memory Add/ Delete V-chip Setup Language Sleep Timer CH / AV(LINE) / DVD Stereo/Audio Output Yes Icon Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No Bilingual SAP Control Level Volume Brightness / Contrast / Sharpness / Color Tint Bass/Treble/Balance Caption / Text Auto Search/Position Game Mute Yes Yes Yes No Yes No Yes Yes A3-2 . Track No.L. Spanish 120 Min 10 Min No No -Min Sec . Program Play Back Surround On/Off Screen Saver JPEG Sleep Timer No Yes Yes Yes Yes No Yes Yes No No Yes Disc/Card Slot Password Lock/ Un Lock Parental Select Files HDMI (480p/1080i/720p) Output OSD Language Clock and Timer No Yes E. French. Chapter No. JPEG ) No No Yes Yes Yes No Yes English. VIDEO CD. Audio Stereo L/R Zoom Marker No.B. Time Sub Title No. Angle No. (Enhanced Black Level) TV Screen Size(4:3) OSD Display On/Off Picture Mode (Video/Film/Auto) JPEG Interval Screen Saver G-11 G-12 Yes Icon Yes Yes Yes Yes No Yes Yes No No No Folder Name File Name File No Time Track No Max Time Step Program(On Timer / Off Timer) On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than A3-3 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes (CD. JPEG ) Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes (Video CD) Yes Yes Yes (CD. VIDEO CD. Vocal On/Off Audio No.GENERAL SPECIFICATIONS G-10 On Screen Display Menu (DVD) Menu Type Language Menu Subtitle Audio OSD Language(Set up Language) Video Audio DRC (Dynamic Range Control) Dialogue (On DRC[TV] / Off DRC[Std]) Surround System Open Close No disc Reading Play Still/Pause Stop Prohibit Mark PBC Step Skip(>>|) Skip(|<<) Random Repeat Slow+ SlowSearch+ SearchJump Resume Title No. C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 Play Stop Search+ SearchClosed Caption/Skip+ Quick View(CH RTN)/SkipSlow+ SlowPause/Still/Step DISPLAY TV/DVD Cancel Audio Select Angle Subtitle Top Menu Menu DVD Menu Return CH Up CH Down Vol Down Vol Up Up/ Set+ Down/ SetLeft/SelectRight/Select+ Enter Play Mode Input Select/Zoom Repeat A-B Mute Open/Close Sleep Marker Jump Game A3-4 No TOSHIBA TOSHIBA 40-BF H. 45-BC H 3V UM-4 x 2 pcs 47 Key Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes .GENERAL SPECIFICATIONS G-13 Remote Control Unit Glow in Dark Remocon Remocon Format Format Custom Code Power Source Total Keys Keys RC-MG Voltage(D. 45-BA H. 44-BB H. GENERAL SPECIFICATIONS G-14 Features (TV) Features (DVD) CABLE Auto Shut Off Auto Setup Auto CH Memory V-Chip Auto Search SAP Game Position FM Transmitter Energy Star Closed Caption Comb Filter Protect of FBT Leak Circuit Picture Preference Choke Coil Power On Memory Tray Lock Video CD Playback SVCD Playback MP3 Playback WMA Playback JPEG Playback Digital Out Down Mix Out G-15 Accessories 3D Surround Screen Saver Closed Caption Audio DAC Owner's Manual USA V-chip CANADA V-chip Yes Yes Yes Yes Yes No No No Yes No No Yes No Yes Yes No No Yes Yes No No No (Dolby Digital) (MPEG) (PCM) (DTS) (Dolby Digital) (DTS) Language w/Guarantee Card Remote Control Unit Battery UM size x pcs OEM Brand Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer 300 ohm to 75 ohm Antenna Adapter Antenna Change Plug Guarantee Card Registration Card Warranty Card ESP Card Service Station List DC Car Cord (Center+) Columbia Offer Sheet Information Sheet (Return) Netflix Card A3-5 Yes Yes Yes Yes Yes Yes No No No Yes 192kHz / 24bit English Yes Yes Yes UM-4 x 2 pcs No No No -No -No Yes No No Yes No No No No No Yes NO . W x D x H (mm) Net (Approx./SearchStill/Pause Stop Main Power SW Main Power SW Power Stand-by On Timer Video Input Audio Input Other Terminal Video Input Audio Input Video Output Audio Output Digital Audio Output Diversity DC Jack 12V(Center +) VHF/UHF Antenna Input Approx.9lbs) No --.Sets --./ ------Double/Brown No 594x569x620 Yes 1 Corner / 3 Edges / 6 Surfaces 46 240 Sets PS 94V0 DECABROM PS 94V0 DECABROM No Yes Green procurement of TOSHIBA Yes .0kg (48.5lbs) 24.GENERAL SPECIFICATIONS G-16 Interface Switch Front Rear Indicator Terminals Front Rear G-17 G-18 Set Size Weight G-19 Carton G-20 Material G-21 Environment Power (Tact) Channel Up Channel Down Volume Up Volume Down Play Open/Close Skip+ /Search+ Skip.7x513 22. R) Head Phone No No No No Coaxial (DVD Only) No No F Type 502x488.0kg (52.) Gross (Approx.) Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material W/Color Photo Label Dimensions W x D x H(mm) Description of Origin Drop Test Natural Dropping At Height (cm) Container Stuffing (40' container) Cabinet Front Rear Jack Panel PCB Non-Halogen Demand Eyelet Demand Environmental standard requirement Pb-free A3-6 Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes No No Yes (Red) No No RCA x 1 RCA x 2(L/MONO. 5. 1-2 B1-1 Fig. 3. Remove the AC cord from the AC cord hook 3. DISCHARGE ELECTRICITY BECAUSE IT CONTAINS HIGH VOLTAGE. Remove the 7 screws 1. CP302. Disconnect the following connectors: (CP301. Remove the 11 screws 1.C. 1 1 Top Shield 1 1 1 1 2 2 2 (A) Front Cabinet DVD Block CRT PCB CP805 2 CP8002 CP8001 (B) AV PCB 3 Jack Shield (C) Bottom Plate Fig. Remove the Anode Cap. Remove the Back Cabinet in the direction of arrow. 2. Disconnect the following connector: (CP805). 8. Remove the screw 3. 7. Remove the screw 2 which are used for holding the Back Cabinet. Remove the 4 screws 2. Remove the DVD Block in the direction of arrow (B). Front Cabinet 1 CP3800 1 CP301 Front Cabinet CP401 1 CP302 AV PCB/DVD Block 1 1 Fig. BOARDS 1. (Refer to REMOVAL OF ANODE CAP) 2. CP401 and CP3800). 3. 1-4 . 2 3 Back Cabinet 1 Fig. UNPLUG THE POWER CORD FROM THE AC SOURCE. Remove the AV PCB in the direction of arrow (C). 4. Remove the Top Shield in the direction of arrow (A). 3. 1-3) 1. Disconnect the following connectors: (CP8001 and CP8002). 6. 1-4) 1 1 1. Remove the 2 screws 1. Remove the Jack Shield.DISASSEMBLY INSTRUCTIONS 1-3: AV PCB/DVD BLOCK (Refer to Fig. 2. 1-2) CAUTION: BEFORE REMOVING THE ANODE CAP. Remove the CRT PCB in the direction of arrow. REMOVAL OF MECHANICAL PARTS AND P. Remove the AV PCB/DVD Block in the direction of arrow. 1-1 1-2: CRT PCB (Refer to Fig. 1 1 1 1 1 1. 2. 1-3 1 1-4: DVD BLOCK (Refer to Fig. 1-1: BACK CABINET (Refer to Fig. 3. 4. 1-1) 1. BEFORE ATTEMPTING TO REMOVE OR REPAIR ANY PCB. 8. Remove the 4 screws 3. 5. Remove the Deck Shield in the direction of arrow (C). Remove the 4 screws 1. Remove the 2 screws 2. Remove the DVD Deck in the direction of arrow (A).DISASSEMBLY INSTRUCTIONS 1-5: DVD PCB/DVD DECK (Refer to Fig. Manual soldering conditions • Soldering temperature: 350 ± 5˚C • Soldering time: Within 2 seconds • Soldering combination: Sn-3. the Laser may be damaged. 3. 6. When installing the DVD Deck.0Ag-0. 2 2 DVD PCB CP2303 CP2302 CP2301 1 Pick Up PCB (B) 1 1 DVD Deck 1 3 (A) 3 Short circuit using a soldering iron. Before your operation. remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector. Short circuit the position shown in Fig. use the drawing equipment over the Pick Up Unit to keep the Flux smoke away from it. When Soldering/Removing of solder. 7. 4. CP2302 and CP2303). Disconnect the following connectors: (CP2301. Use the Lead Free solder. 1-5 NOTE 1. 3 3 Deck Shield (C) Deck Angle Fig. B1-2 . 1-5 using a soldering iron. 2. please read “PREPARATION OF SERVICING”. If you remove the DVD Deck with no soldering. 1-5) 1. 3.5Cu 4. 2. 5. Remove the DVD PCB in the direction of arrow (B). (3) Traverse Holder (2) Main Frame Ass'y (1) Main Chassis Ass'y (4) (4) Check Lock Fig. Remove the screw 1. 2-2-C . 4. 2-2-C. (Refer to Fig. Remove the Insulator (R) from the Main Frame Ass'y. 2-2-B) 2.DISASSEMBLY INSTRUCTIONS 2. hook the wire on the Main Frame Ass'y as shown Fig. Unlock the 2 supports 2. In case of the Main Chassis Ass'y. 2-1-B 2-2: MAIN CHASSIS ASS'Y (Refer to Fig. Main Frame Ass'y 2-1: TRAY (Refer to Fig. install it from (1) to (4) in order. Set the Tray opened. replace the DVD MECHA ASS'Y.5kgf•cm Main Frame Ass'y Fig. 2-2-B Tray Main Frame Ass'y Fig. REMOVAL OF DVD DECK PARTS 1 2 NOTE 2 1. Minute adjustments are needed if the disassemble is done. 2-2-A) 1.0 ± 0. 3. (Refer to the DISC REMOVAL METHOD AT NO POWER SUPPLY) 2. In case of the Main Chassis Ass'y installation. If the repair is needed except listed parts. Do not disassemble the DVD DECK PARTS except listed parts here. Main Chassis Ass'y • Screw Torque: 2. 2-1-A) Insulator (R) 1. 2. Remove the Main Chassis Ass'y. Check Hook B2-1 Fig. Unlock the 2 supports 1 and remove the Tray. In case of the Tray installation. install them as the circled section of Fig. 1 Tray 1 Main Frame Ass'y (Bottom Side) Fig. 2-2-A NOTE 1. 2-1-A (3) Rack Loading NOTE (3) 1. 2-1-B so that the each markers are met. check if the value of the Fig. 2-3-B 1 The Lever should be position between A and B. 3. 2-4-A) No gap Fig. When installing the Loading Motor PCB Ass'y. 3.0 ± 0. 2-3-C. 2-3-B is correct. Pulley Motor Fig. Pulley Gear Remove the Loading Belt. In case of the Loading Motor PCB Ass'y installation. Remove the screw 1.1mm Clamper Magnet Loading Motor Main Frame Safety surface for pressing of the insert. In case of the Pulley Motor installation. Fig. install it correctly as Fig. 2-3-A NOTE Main Gear 1.0 ± 0. Unlock the support 2 and remove the Pulley Gear. 2-5-A) 1. then unlock the 3 supports 1.3kgf•cm (Screw 1) • Screw Torque: 1. Remove the Main Gear. 5. Remove the 2 screws 2. In case of the Clamper Ass'y installation. Remove the Loading Motor PCB Ass'y. 2-4-B 2-5: CLAMPER ASS'Y (Refer to Fig. 2-3-A) 1. Clamper Magnet and Clamper. 2. Rack Loading Pulley Gear 1 Check Hook Loading Motor PCB Ass’y • Screw Torque: 2. 2-4-B. Remove the Pulley Gear. Press down the catcher 1 and slide the Rack Loading. 3.5 ± 0.3kgf•cm (Screw 2) Fig. do not mesh it to the Main Gear as shown the Fig. B2-2 . 2. 2-5-B 1. 4. 2-3-C Clamper 2-4: RACK LOADING/MAIN GEAR/PULLEY GEAR (Refer to Fig. Rack Loading A 1 Clamper 1 Fig. 2-3-C. Remove the Clamper Plate. hook the wire on the Main Frame Ass'y as shown Fig. 2. Press the Clamper and rotate the Clamper Plate clockwise. In case of the Rack Loading installation. 2-5-B. 2. Clamper Plate Check Hook Loading Motor PCB Ass’y Fig. Clamper Plate 7. 2-4-A 2 NOTE Main Frame Ass’y 1.DISASSEMBLY INSTRUCTIONS 2-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT (Refer to Fig. 2-5-A B NOTE 1. install correctly as Fig. Main Gear Main Frame Ass’y Loading Belt 2 2 Rack Loading 1 Fig. When pushing the Rack Feed in the direction of the arrow. Remove the Switch PCB Ass'y. Remove the Feed Motor. • Install wire from (1) to (4) in order. In case of the Insulator (F) installation. 2-7-C Insulator (R) Main Chassis Ass'y (Top Side) ~ FEED MOTOR ~ BLUE (4) ORANGE (3) Fig. check if the value of the Fig. Remove the 2 screw 3. 3. 4. In case of the Motor Gear installation. In case of the Insulator (R) installation. Fig. 2-7-B) 2. 2. 3.DISASSEMBLY INSTRUCTIONS 2-6: TRAVERSE HOLDER/INSULATOR (F)/INSULATOR (R) (Refer to Fig. 2-7-D Main Chassis Ass'y (Bottom Side) 1 Check Hook Check Hook 2 Rack Feed Ass'y 3 Check Hook 3 Switch PCB Ass'y Check Hook Motor Gear • Loosen the wire in the direction of the arrow. (Refer to Fig. 2-7-A) 1. 4. 2-6-A Push Rack Feed Ass'y NOTE Fig.3kgf•cm (Screw 1) • Screw Torque: 3. 2-7-A B2-3 Fig.3kgf•cm (Screw 3) Feed Motor Fig.3kgf•cm (Screw 2) • Screw Torque: 1. After the assembly of the Main Chassis Ass'y.0 ± 0. Motor Gear 6. 2. it should be restored to the original position by the spring force. Remove the Motor Gear. 2-7-C is correct. Remove the Rack Feed Ass'y. install correctly as Fig. 2-6-C. Remove the screw 2. Main Chassis Ass'y • Screw Torque: 5.2mm Insulator (F) Feed Motor Traverse Holder Safety surface for pressing of the insert. Remove the 2 Insulator (F). 5. Fig. When installing the wire of the Switch PCB Ass'y. install correctly as Fig. BLACK (2) RED (1) Remove the screw 1. 2. 2-7-E. 2-6-C Switch PCB Ass'y ~ SPINDLE MOTOR ~ 2-7: RACK FEED ASS'Y/SWITCH PCB ASS'Y/FEED MOTOR (Refer to Fig. 1. 2-6-A) NOTE 1.0 ± 0. 6. Remove the Traverse Holder. Remove the Insulator (R). 2-7-E .0 ± 0. 7. 2-7-B 1.0 ± 0. 3. 2-6-B. Insulator (R) Main Chassis Ass'y Insulator (F) Traverse Holder Insulator (F) Fig. 2-7-D. install it correctly as Fig. 2-6-B Fig. hook the wire on the Main Chassis Ass'y as shown Fig. fold it correctly and install it as shown from Fig. 2-8-A to Fig. Fig. [ 24 pin FFC ] Pick Up Side Printing Surface Fold it by 90˚ 54 ± 1mm Fold Printing Surface 43 ± 1mm Fig. Do not make the folding lines except the specified positions for the FFC. 2-8-A [ 6 pin FFC ] (1) Reinforcement Plate (3) Reinforcement Plate 59 ± 1mm 10 ± 1mm Printing Surface Printing Surface Fold Reinforcement Plate Fold (4) Fold Printing Surface (2) 10 ± 1mm Printing Surface Fold Printing Surface 44 ± 1mm • Proceed the steps (1) through (4). 2-8-C. When installing the FFC. NOTE 1. Fold Printing Surface 60 ± 1mm Fig. 2-8-B [ 5 pin FFC ] (1) Reinforcement Plate (3) Reinforcement Plate 55 ± 1mm 10 ± 1mm Printing Surface Printing Surface Fold Reinforcement Plate Fold (4) Fold 10 ± 1mm Printing Surface Printing Surface (2) • Proceed the steps (1) through (4).DISASSEMBLY INSTRUCTIONS 2-8: FFC WIRE HANDLING 1. 2-8-C B2-4 . Turn over the Rubber Cap. After one side is removed. Take care not to damage the Rubber Cap. When removing the Anode Cap. Clean the spot where the cap was located with a small amount of alcohol.) CRT Screwdriver Support Alligator Clip GND on the CRT Fig. Location of Anode Cap GND on the CRT Fig. then the other as shown in Fig. While holding the plastic part of the insulated Screwdriver. B3-1 Fig. 3-3 2.) Rubber Cap CRT CRT Support Fig. pull in the opposite direction to remove the other.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. REMOVAL OF ANODE CAP Read the following NOTED items before starting work. Follow the steps as follows to discharge the Anode Cap. 3-5. 6. 2. Confirm that the Support is securely connected. 3. dust. this may cause the spring to be damaged. NOTE * After turning the power off there might still be a potential voltage that is very dangerous. Insert one end of the Anode Support into the anode button. * Do not use pliers to loosen or tighten the Anode Cap terminal. 3-4 Fig. touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. 3. 3-1. at the spot where the cap was located. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3-3. 3-2. (Refer to Fig.DISASSEMBLY INSTRUCTIONS 3. INSTALLATION 1. make sure to discharge the Anode Cap's potential voltage. Put on the Rubber Cap without moving any parts. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. 1. etc. 3-1 4. 3-5 .) REMOVAL NOTE Confirm that there is no dirt. (Refer to Fig. (Refer to Fig. 3-2 Support 5. (Refer to Fig. 3-4. 4-2 IC pattern Fig. NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads. 4-4. 4-1. 4. Blower type IC desoldering machine IC Masking Tape (Cotton Tape) Tweezers Fig. Peel off the Masking Tape.) NOTE Some ICs on the PCB are affixed with glue. (Refer to Fig. Blower type IC desoldering machine Braided Shield Wire Soldering Iron IC Fig. Absorb the solder left on the pattern using the Braided Shield Wire. 5. pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. 4-3 NOTE Do not rotate or move the IC back and forth .DISASSEMBLY INSTRUCTIONS 3. so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it. (Refer to Fig. 4-3.) IC Fig. Heat the IC leads using a blower type IC desoldering machine.) 4. 4-2.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL 1. When IC starts moving back and forth easily after desoldering completely. 4-4 B4-1 . 4-1 2. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. until IC can move back and forth easily after desoldering the leads completely. (Refer to Fig. 4-6 3. correct by resoldering. Soldering Iron IC Braided Shield Wire Fig. Absorb the solder left on the lead using the Braided Shield Wire. Then solder each lead on the diagonal positions of IC temporarily. When bridge-soldering between terminals and/or the soldering amount are not enough. 2. 4-8. (Refer to Fig.) INSTALLATION 1.) IC Thin-tip Soldering Iron Soldering Iron Fig. resolder using a Thintip Soldering Iron.DISASSEMBLY INSTRUCTIONS 4. (Refer to Fig. (Refer to Fig.) NOTE Do not absorb the solder to excess. (Refer to Fig. So. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. 4-5. always be sure to replace the IC in this case. If the bending of leads are repaired.) Soldering Iron Solder IC Supply soldering from upper position to lower position Fig. 4-6. 4-8 Solder temporarily 5. Finally. 4-5 NOTE When the IC leads are bent during soldering and/or repairing. If some abnormality is found. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. the pattern may be damaged. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. confirm the soldering status on four sides of the IC using a magnifying glass. 4-7. do not repair the bending of leads. 4-7 B4-2 . Solder temporarily Fig. NOTE: Do not use this for normal servicing. Operations WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM. If you set factory initialization. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition. To enter to the SERVICE MODE function. POWER ON total nours and MICON VERSION. Turn on the POWER. 1. Set the VOLUME to minimum. TV mode VOL. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). 4. = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) . Can be checked of the INITIAL DATA of MEMORY IC. and set to the TV mode. 2. Check of the SUM DATA. DOWN (Minimum) 6 2 sec. ALL mode VOL. TV mode VOL. Releasing of PARENTAL LOCK. examine and adjust easily. 3. (See below chart. POWER ON total hours and MICON VERSION can be checked on the screen.SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". NOTE: If you set a factory initialization. Display of the Adjustment MENU on the screen. DVD mode (No disc) STOP 7 3 sec. the total hours is reset to "0". the memories are reset such as the channel setting. ROM : 20C2 Rom correction data check sum. DOWN (Minimum) 8 2 sec. Refer to the "TRAY LOCK". Initialization of factory DVD data. CRT ON 0000 FIG. turn off the power. The disk cannot be taken out. OEC6087A_115 MICON Version INIT : 1672 Initialsetting data check sum. DVD mode (STOP) STOP 9 3 sec. DVD mode (No disc) VOL. TV mode VOL. After the confirmation of each check sum. Initialization of factory TV data. NOTE: Do not use this for normal servicing. DOWN (Minimum) 9 2 sec. DOWN (Minimum) 4 2 sec. DOWN (Minimum) 0 2 sec. Refer to the "PARENTAL CONTROL . DOWN button on the set and Channel button (8) on the remote control for more than 2 seconds. DOWN (Minimum) 1 2 sec. and the POWER ON total hours. Releasing of V-CHIP PASSWORD. 1 C-1 POWER ON total hours. Press both VOL. Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.) Set Condition Set Key Remocon Key Standard Time TV mode VOL. POWER ON total hours and MICON VERSION on the screen. POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC. Total hours are displayed in 16 system of notation.RATING LEVEL". After the data input. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. the unit will turn off automatically. ADDRESS is now selected and should "blink". ADDRESS DATA OEC6087A_115 INIT 00 80 CRT ON 0000 FIG. When DATA is selected. ADDRESS and DATA should appear as FIG 1. When satisfied correct DATA has been entered. it will "blink". Turn POWER on.WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF INITIAL DATA If a service repair is undertaken where it has been required to change the MEMORY IC. 8. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. Again. 10. turn POWER off (return to STANDBY MODE) to finish DATA input. step through the ADDRESS until Press RIGHT/LEFT button to select DATA. Repeat steps 4 to 6 until all data has been checked. the following steps should be taken to ensure correct data settings while making reference to TABLE 1. 6. 5. INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 00 80 04 E2 4C 4F 12 33 55 35 94 23 00 89 70 70 00 10 0C 00 00 00 05 7B A0 50 21 74 50 00 00 10 55 35 20 80 88 83 88 89 88 00 00 0A 0C 0E 10 12 14 16 18 30 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 28 40 29 29 2A 2A 2B 2B 2C 2C 2D 2D 2E 2E 2F 2F 30 30 50 31 31 32 32 33 33 34 34 35 36 37 38 3B 3E 41 44 60 47 4A 4D 50 53 56 5A 5F --- --- --- --- --- --- --- --- Table 1 1. 9. Press both VOL. and set to the TV mode. Using the UP/DOWN buton on the remote. Set the VOLUME to minimum. After the finishing of the initializing of shipping. step through the DATA using UP/DOWN button until required DATA value has been selected. 3. 2. Turn on the POWER. 1 4. 11. Pressing RIGHT/LEFT button will take you back to ADDRESS for further selection if necessary. Press both VOL. set to the initializing of shipping. C-2 . The unit will now have the correct DATA for the new MEMORY IC. 7. 2. (Old grease may cause damages to the IC and Transistor). 1-1. 5. AV(MAX) BRI.) COL. 6. Using the remote control. AV(MIN) COL. 3. Adjust the Focus Volume until picture is distinct. Press the MENU button on the remote control to end the adjustments.ELECTRICAL ADJUSTMENTS 1. 4.) BRI. 3.5V. GAME(CENT) BRI. Adjust the Screen Volume until a dim raster is obtained. Using the remote control. NO. AV(CENT. 1-2. CONT. FUNCTION 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 OSD H CUT OFF H VCO H PHASE V SIZE V POSITION R DRIVE B DRIVE R CUT OFF G CUT OFF B CUT OFF BRIGHTNESS(CENT. DVD(CENT. 1.) CONTRAST(MAX) CONTRAST(MIN) COLOR(CENT. B DRIVE=3F 2. 4. DVD(MIN) TINT DVD SHARPNESS DVD BRI.) COL. Function Step No. FUNCTION NO. On-Screen Display Adjustment 1. • When removing a PCB or related component.) BRIGHTNESS(MAX) BRIGHTNESS(MIN) CONTRAST(CENT. DVD(MAX) BRI. Receive the monoscope pattern. R CUT OFF=7F. 1-2 2. DVD(MIN) COL. DVD(MAX) COL. Press the VOL. GAME(MAX) BRI. GAME(MIN) TUNING V MUTE POWER ON V MUTE INPUT LEVEL SEPARATION L SEPARATION H 2-2: FOCUS 1. BEFORE MAKING ELECTRICAL ADJUSTMENTS Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. R DRIVE=3F. DVD(CENT. AV(CENT.) CONT. set the brightness and contrast to normal position. G CUT OFF=7F. after unfastening or changing a wire. 2. GAME(MIN) CONT. DOWN button on the set and the Channel button (9) on the remote control for more than 2 seconds to appear the adjustment mode on the screen as shown in Fig. 5. 1-1 3. Before applying new silicon grease. 2. AV(MAX) Prepare the following measurement tools for electrical adjustments. Use the Channel UP/DOWN button or Channel button (1-0) on the remote control to select the options shown in Fig. CAUTION • Use an isolation transformer when performing any service on this chassis. 2-3: CUT OFF 01 OSD 17 1. be sure to put the wire back in its original position. 3. AV(MAX) COL. 2. AV(CENT. Turn the Focus Volume fully counterclockwise once. discharge electricity because it contains high voltage.) CONT. GAME(CENT) CONT. DVD(CENT. AV(MIN) CONT. 1-1 and press the channel button (02) on the remote control to select "CUT OFF". Adjust the unit to the following settings. 4. Set the VOLUME to minimum. 4. Activate the adjustment mode display of Fig.) BRI. GAME(MAX) CONT. apply silicon grease on the contact section of the heat sink. • Before removing the anode cap. Set condition is Aging Test for more than 15 minutes. Place the set in AV MODE without signal. Fig. Set condition is AV MODE without signal. DVD(MIN) CONT. 3. Adjust the VR3800 until the digital voltmeter is 132 ± 0. B CUT OFF=7F.) COLOR(MAX) COLOR(MIN) TINT SHARPNESS BRI. Oscilloscope Digital Voltmeter AC Voltmeter Pattern Generator Multi-Sound Signal Generator Fig. • When you exchange IC and Transistor with a heat sink. DVD(MAX) CONT. set the brightness and contrast to normal position. D-1 . Connect the digital voltmeter to TP401. AV(MIN) TINT AV SHARPNESS AV BRI. remove all the old silicon grease. BASIC ADJUSTMENTS 2-1: CONSTANT VOLTAGE 1. .. Receive the gray scale pattern from the Pattern Generator. Press the RIGHT/LEFT button on the remote control until the white 0% is begin to shine. set the brightness and contrast to normal position. 2-8: BRIGHT CENTER 1. 1-1 and press the channel button (04) on the remote control to select "HPOSI". 11. Press the RIGHT/LEFT button on the remote control until the white 0% is begin to shine. 1-1 and press the channel button (23) on the remote control to select "BRTCA". 12. 3.ELECTRICAL ADJUSTMENTS 2-4: WHITE BALANCE 2-7: VERTICAL SIZE NOTE: Adjust after performing CUT OFF adjustment. 2-5: HORIZONTAL POSITION 1. Receive a broadcast and check if the picture is normal. . 4. 1-1 and press the channel button (06) on the remote control to select "VPOSI". 5. 4. 5. 4. G CUT OFF and B CUT OFF at each step tone sections equally. 7. Activate the adjustment mode display of Fig. 3. . 4. Using the remote control. Using the remote control. Press the RIGHT/LEFT button on the remote control to set the same step numbers as the AV. set the brightness and contrast to normal position. 8. 2. "R CUT OFF". 1. 1-1 and press the channel button (05) on the remote control to select "VSIZE".. 2-1 D-2 . 1-1 and press the channel button (34) on the remote control to select "BRTCD". Receive the monoscope pattern. UP/DOWN button on the remote control to whiten the B DRIVE. 1-1 and press the channel button (12) on the remote control to select "BRTC". 3. R CUT OFF. Press the RIGHT/LEFT button on the remote control to set the same the same step numbers as the AV.. Activate the adjustment mode display of Fig. . 1-1 and press the channel button (45) on the remote control to select "BRTCG". 5. Press the INPUT button on the remote control to set to the AV mode. Activate the adjustment mode display of Fig. Notch Shadow mask Fig. 10. Place the set in Aging Test for more than 15 minutes. 3. 2-1) horizontal line . set the brightness and contrast to normal position. 1-1 and press the channel button (07) on the remote control to select "R DRIVE". Press the CH. Activate the adjustment mode display of Fig. Check if the step No. . 13. 2. (Audio Video Input) 6. Press the RIGHT/LEFT button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. (Refer to Fig... set the brightness and contrast to normal position. . UP/DOWN button on the remote control to select the "B DRIVE". Activate the adjustment mode display of Fig. Receive the monoscope pattern. 4. Press the RIGHT/LEFT button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 10 ± 2%. Receive the monoscope pattern. Adjust the VOL. 3. Receive the monoscope pattern.. (RF Input) 2. 2. Using the remote control. Press the INPUT button on the remote control to set to the GAME mode. 7. set the brightness and contrast to normal position. Using the remote control. 15. Perform the above adjustments 5 and 6 until the white achieved. Using the remote control. Activate the adjustment mode display of Fig. 14. 5. set the brightness and contrast to normal position. 2-6: VERTICAL POSITION 1. 9. 2. 1. Using the remote control.. Receive the monoscope pattern. 6. Press the TV/DVD button on the remote control to set to the DVD mode. V POSI is "02". . Activate the adjustment mode display of Fig. "G CUT OFF" or "B CUT OFF". Adjust the VR402 until the horizontal line becomes fit to notch of the shadow mask. Activate the adjustment mode display of Fig. (Refer to Fig. set the brightness. color and tint to normal position. Press the INPUT button on the remote control to set to the AV mode. 1-1 and press the channel button (18) on the remote control to select "COLC". Activate the adjustment mode display of Fig. (RF Input) 2. Using the remote control. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 2-4) 7. Activate the adjustment mode display of Fig. Connect the oscilloscope to TP022. 2-3 D-3 Red Level Fig. 10. Press the RIGHT/LEFT button on the remote control until the section "A" becomes a straight line. Receive the color bar pattern. 1-1 and press the channel button (29) on the remote control to select "COLCA". 3. 1-1 and press the channel button (40) on the remote control to select "COLCD". 3. 9. (Refer to Fig. 4. (Refer to Fig. (RF Input) 2. Press the RIGHT/LEFT button on the remote control until the red color level is adjusted to 110 ± 10% of the white level. contrast. Connect the oscilloscope to TP024. 10. contrast. Using the remote control. 8. 1-1. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. set the brightness. Using the remote control. 1-1 and press the channel button (43) on the remote control to select "TNTCD". color and tint to normal position. 2-3) 11. (Refer to Fig. Receive the color bar pattern. 13. Press the RIGHT/LEFT button on the remote control until the difference of A and B becomes minimum. Activate the adjustment mode display of Fig. Using the remote control. color and tint to normal position. 2-4) 13. Activate the adjustment mode display of Fig. Press the INPUT button on the remote control to set to the AV mode. (Refer to Fig. color and tint to normal position. Activate the adjustment mode display of Fig. 2-2) 1. 9. Receive the color bar pattern. 15. Press the RIGHT/LEFT button on the remote control until the red color level is adjusted to 110 ± 10% of the white level. 2. 5. 2-4 . 1-1 and press the channel button (21) on the remote control to select "TNTC". (Audio Video Input) 8. 12. Press the RIGHT/LEFT button on the remote control to set the same the same step numbers as the AV. Press the RIGHT/LEFT button on the remote control to set the same the same step numbers as the AV. 5. 2-2 2-10: TINT 1. 4. contrast. 14. White 0% 100% White 100% "A" Fig. 1-1 and press the channel button (32) on the remote control to select "TNTCA". Press the TV/DVD button on the remote control to set to the DVD mode. 01 OSD 17 A B Fig. 12. 6. Activate the adjustment mode display of Fig. Press the TV/DVD button on the remote control to set to the DVD mode. Receive the color bar pattern. contrast. set the brightness. 11. 2-3) 6.ELECTRICAL ADJUSTMENTS 2-9: OSD POSITION 2-11: COLOR CENTER 1. set the brightness. Press the RIGHT/LEFT button on the remote control until the section "A" becomes a straight line. Activate the adjustment mode display of Fig. (Audio Video Input) 7. Press the RIGHT/LEFT button on the remote control to set the same step numbers as the AV. Press the INPUT button on the remote control to set to the GAME mode. Activate the adjustment mode display of Fig. becomes "40" 3. 1-1 and press the channel button (49) on the remote control to select "CNTXG". DVD(MAX) COL. GAME(MIN) TUNING V MUTE POWER ON V MUTE STEP NO. Press the RIGHT/LEFT button on the remote control to set the same the same step numbers as the AV. AV(MAX) COL. 8. Press the RIGHT/LEFT button on the remote control until the contrast step No. Press the RIGHT/LEFT button on the remote control until the contrast step No. 1-1 and press the channel button (16) on the remote control to select "CNTX". AV(MAX) BRI.) CONT. 04 7F 15 30 10 50 00 29 7F 15 30 10 50 00 29 7F 15 30 10 50 00 29 7F 15 30 10 00 40 . Receive a broadcast and check if the picture is normal. 1-1 and press the channel button (27) on the remote control to select "CNTXA". DVD(CENT. 12. 9. 6. Press the TV/DVD button on the remote control to set to the DVD mode. GAME(MAX) BRI. AV(MIN) CONT. 2. DVD(MIN) COL. Activate the adjustment mode display of Fig. Press the INPUT button on the remote control to set to the AV mode. AV(CENT.) CONT. AV(MIN) SHARPNESS AV BRI. 10. DVD(MIN) SHARPNESS DVD BRI.) 1.) CONTRAST(MIN) COLOR(MAX) COLOR(MIN) SHARPNESS BRI. DVD(MIN) CONT. Activate the adjustment mode display of Fig. GAME(MIN) CONT. becomes "40" 7. 4. 03 13 14 15 17 19 20 22 24 25 26 28 30 31 33 35 36 37 39 41 42 44 46 47 48 50 51 52 D-4 FUNCTION H VCO BRIGHTNESS(MAX) BRIGHTNESS(MIN) CONTRAST(CENT. DVD(MAX) BRI. GAME(CENT) CONT. Please check if the fixed values of the each of the adjustment items are set correctly referring below. Receive a broadcast and check if the picture is normal. NO.ELECTRICAL ADJUSTMENTS 2-12: CONTRAST MAX 2-13: Confirmation of Fixed Value (Step No. 5. 13. Activate the adjustment mode display of Fig. AV(MIN) COL. 11. 1-1 and press the channel button (38) on the remote control to select "CNTXD". 3. then tighten the fixing screw. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. Receive the green raster pattern from color bar generator. 2. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. (Refer to Fig. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Confirm red and blue colors. Receive the crosshatch pattern from the color bar generator. (Refer to Fig. 6. Place the CRT surface facing east or west to reduce the terrestrial magnetism. WEDGE WEDGE WEDGE DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 6 POLE MAGNETS 4 POLE MAGNETS PURITY MAGNETS Fig. Turn ON the unit and demagnetize with a Degauss Coil. 3. Move the deflection yoke backward (to neck side) slowly. 3-2-a Adjust after performing adjustments in section 3-1. Refer to the adjusted CRT for the position. 3-2-a) 2. 5. 3-2-b) RGB RGB R G B 3-2: PURITY R G B UPWARD/DOWNWARD SLANT NOTE RIGHT/LEFT SLANT Fig. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 1. Adjust the slant of the deflection yoke while watching the screen. 3-1) If the deflection yoke and magnet are in one body. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. 5. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. 3-1 D-5 WEDGE POSITION Fig. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. Slide the deflection yoke until it touches the funnel side of the CRT. 1. 2. 2. Tighten the screw for the magnet. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. 3-2-b . Receive the green raster pattern from the color bar generator.ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. 3. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. with red and blue on the sides. 7. 1. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 4. 4. 3. using the pair of purity magnets. NOTE 1. Adjust the pair of purity magnets so the color at the ends are equally wide. untighten the screw for the body. 2. Adjust center of screen to green. and stop it at the position when the whole screen is green. (Refer to Fig. Switch the color bar generator from the green raster pattern to the crosshatch pattern. Adjust the pair of purity magnets to center the color on the screen. ELECTRICAL ADJUSTMENTS 4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) CRT PCB CD805 CP805 TP022 TP024 TP023 J801 CP802B CP803B CD803 CRT CD802 VR3800 J4201 CP 80 3A FB401 TP401 CP401 CP101 AC IN TU001 R408 CD3800 CRT S3801 S3802 CP3800 CRT VR402 CP802A CP8002 CD302 J2201 J2204 J2202 SPEAKER (SP351) SPEAKER (SP352) J2203 CP8001 CD8101 CD301 CP301 CP302 AV PCB DVD DECK CP2303 CP8101 CP2302 CD4002 CP2301 DVD PCB CD2001 CD2301 CD2302 D-6 . CKE. VC SPINDLE/ STEPING/ SLED MOTOR TR+/-. RAS#. TIN_SW. E. MOT_SPDL+/- Motor Drive IC2301 LA6565VR-TLM-E SPINDLE/SLED/ FOCUS/TRACK_PWM. A. HD0~D15. LD. WE#. MEMCS0.8V C---3. MOT_SLED+/-. D.3V B---1. RD. B. SD_BA0 HA0~A19. DVD_LD. B REG+3. CS0#. MOT_LD+/-. F SSCRXD SSCCLK OPU RDY[I/O(0)] DVD/CD. AMCLK. ASDATA0 STEREO DAC IC8102 PCM1753DBQR AUDIO L AUDIO R D SD_A0~A10 SD_D0~D15 16M SDRAM IC4009 M12L16161A-7TG A A---3. CD. WR ML. MD. TOUT_SW A FLASH 16M IC4007 SST39VF1601-70-4C-EKE RAMDQM. 1.DVD BLOCK DIAGRAM TV BLOCK DVD LOADER DM-3S A D A. CAS#. ALRCLK. C. ABCLK.8V D---5V E---6V E-1 E-2 . TRAY_CLOSE/OPEN MPEG/MICON/DSP/RF_AMP IC4001 ZR36862PQCG-B SPDIF DVD C DVD Y DVD RESET DRVSB E ZERO HOME.9V IC4003 BA33E00WHFP-TR B C DVD/CDPD SSCTXD RF. CLK. MC. FO+/-.3V. CON+12V 4 2 2 2 V L R J4201 J2202 J2203 J2204 2 2 SOUND AMP IC352 AN7513 L CH SPEAKER SP351 R CH SPEAKER SP352 6 8 SOUND+B 4 2 SOUND AMP IC353 AN7513 6 7 8 2 3 5 SOUND+B E-3 1 HEADPHONE JACK J2201 E-4 .OUT IC401 LA78040N-E 7 30 R 11 HV CHROMA IC601 M61277FP-DF0H MUTE SW *A---AT+5V *B---P. Q4206 L MUTE SW Q4201 SPDIF 29 2 15 3 14 4 16 6 27 9 R.CON+9V *C---P.OUT 1 8 FBT F S 7 9 40 Q101 10 FB401 Q406 Q405 6 F V.VOL DOWN VOL UP CH UP CH DOWN TV BLOCK DIAGRAM OS2202 RESET IC103 PST3231NR 1 2 1 MEMORY IC199 AT24C04N-10SU-2.OUT G.OUT CRT V801 B.DRIVE H.OUT DY801 32 35 24 23 DRIVER 41 21 H.7 *A *A 6 POWER ON/OFF 31 OPEN/CLOSE STOP X101 16MHz PLAY TU001 13 18 12 19 MICON IC101 OEC6087A 27 5 29 SCL SDA AUDIO OUT 10 11 13 20 22 23 28 32 SKIP FF 1 7 6 8 5 34 33 36 37 43 SKIP REW *B *C FROM DVD BLOCK 26 12 DVD C DVD Y 10 DVD_RESET 18 8 SSCRXD SSCTXD SSCCLK 28 RDY(I/O(0)) AUDIO L AUDIO R Q4205 ZERO X602 3.579545MHz 11 MUTE SW Q4202~Q4204.CON+5V *D---P. Q3800 FEED BACK SW IC3800 PS2561AL1-1-V(W) 18 2 4 MOTOR+B (+6V) 17 14 Q3005 DRIVER P. IC3001 BA00BC0WT-V5 8 Q3803 POWER 5 VR3800 +B ADJ.CON+9V Q3002 DRIVER P. ON SW L3800 DEGAUSS COIL P.POWER BLOCK DIAGRAM Q3001 DRIVER UNREG+3. D3816 AC IN F3800 P.CON+12V Q3007 P.8V Q3003 P. ON SW POWER ON-H +B FB401 2 E-5 E-6 .CON+5V REG. D3815. IC3002 KIA278R05PI 2 1 TRANSFORMER SWITCHING T3800 D3808. D3809.CON+5V P.CON+5V (DVD) Q3008 DRIVER RECTIFIER AT+5V 10 SOUND+B 12 FEED BACK MOTOR+6V REG. F-1 CD4002 IC4003 C8113 C8126 R8112 W824 W826 DME060A C4095 C4072 C4076 B4003 B4016 C4002 C4075 B2303 C2315 Q2304 B2305 C2326 B2304 C2347 C2342 R2302 B4013 C4057 B4012 C4056 C4003 B4011 C2365 R2347 B4007 B4005 C4082 C4010 R4022 R2359 C2318 R2339 R2313 C2332 Q2305 C4036 B4006 C4013 B4014 C4033 R4043 D4004 B4008 C4099 C4014 C4019 C4020 C4004 W837 D4002 W806 D4007 C4047 C4018 R4008 B4018 R2348 D4006 C4077 R4064 C4022 C4030 B4001 C4086 R2336 C2301 C2306 C2359 C2360 R2346 C2331 R2357 R2358 C2305 C2357 C2313 B2301 R2356 B2302 C2358 R2353 R2351 R2350 R2342 R2352 R2349 Q2303 C4097 C4080 W850 C4065 C4012 R4048 C4023 C4024 C4025 R4026 R4027 C4046 C4045 C4029 C4031 R4025 R4024 C4098 C4108_1 C4101 C4007 W836 C4052 C4040 C4027 R4072 R4018 R4045 R4012 R4042 R4038 C4026 R4016 C4041 C8120 B8103 R4039 X4001 C4059 C8106 C4034 C4032 C4015 D8111 R2323 C8108 C4074 C4109 R2329 C4035 R2335 C2314_1 C2307 R2328 D4005 R4014 C4069_1 R2338 IC2301 R2330 R4037 R4001 R2337 R4081 R8113 R4021 R4019 W842 R4020 D4003 R4002 R2325 C8105 R4036 105 C8104 R4069 R4004 R4005 R4003 157 D8112 IC4001 C8121 C4081 C4028 R2301 R2308 R2321 C2304 D2304 D2303 R2304 R2327 R2324 R2326 L8102 IC4007 CP2303 R4070 W818 C4016 C4017 R4071 53 B4010 C4088 C4085 R2320 R2310 L8103 IC4009 IC8102 1 C4038 R2305 R2307 R2319 CP2302 C8107 C8119_1 R4040 C2303 R2303 C2302 C2310_1 W843 C2329_1 R2360 C2348 CP2301 C8125 R4051 C8114 C4096 W819 C8109 C4050 R4060 R4062 R2334 C2309 C8122 C4009_1 R4052 R4063 R4077 C4053_1 C4068_1 C2341_1 R2306 C2328_1 Q2301 R2340 C2346_1 C2327_1 C2340_1 C2343_1 R4061 B4009 C4001 R4078 C4106 R4041 C4008 W829 C4039 C4078_1 C4021 C4064 C4062 C4070 R2355 C4011_1 R4050 C4083_1 C4067_1 W854 C4071_1 B4002 R2332 R2333 R4009 R4080 W808 R4033 R4053 R4054 C4063 DVD (TOP SIDE) C4066 L4001 C4084_1 C4044 C4090 Q2302 C4089 C4100 PRINTED CIRCUIT BOARDS DVD (BOTTOM SIDE) R2318 R2341 R2309 R4058 R4059 CP8101_3 DME060A F-2 . SEE INSIDE BACK COVER.PRINTED CIRCUIT BOARDS AV/CRT (INSERTED PARTS) SOLDER SIDE R467 _1 23 C4 C422 R430 50 R4 D3814 R3813 C3822 D3820 C3823 D3827 D3818 C3826 D3821 D3828 C3824 R3831 R3815 R3833 C 38 16 C3815 C648 D3806 C649 D3822 W833 D3801 R3805 TH3800_2 Q3800 R3804 R614 W063 L601 W060 L603 IC3800 W027 W007 C38 11 R3825 B3800 R3812 D3816 Q3803 HS3800 W820 R3826 R3828 R3817_1 W867 W889 W802 C3807 D3815 L3801 W884 R3827 W061 W062 C3812 W059 D3809 C3814 C3810 W005 R3 80 6 B4201 R3822 TU001 W823 C006 L001 L4202 C4204 W008 R4205 W828 W029 W009 R 30 05 R3818 W031 R003 W030 R004 W033 FH3801 J4201 D3812 D3807 RISK OF FIRE .REPLACE AS MARKED. W032 R3017 W035 W034 CP802A FH3800 W010 D3804 C3002 W065 C3010 W134 W135 R4204_1 W067 W220 W068 W071 W070 W072 W137 W138 W066 F3800 S3801 R3816 Q3802 W808 R3015 Q3001 R3820 D3810 R3821 S3802 C3808 W844 W818 W834 W142 W821 W139 W140 C3011 W141 W143 W144 W145 W146 W208 CP8002 C432 D3831 W001 C402 R445 R3802 C3818 W014 W025 D3823 CP3800 W045 C639 W149 W147 W853 C119 W205 W206 C4201 CP301 C439 R423 D410 C431 R453 W002 W211 D3811 D3803 C3017 W018 W016 D3819 D3817 T3800 FOR SERVICE INFORMATION ABOUT CRITICAL COMPONENTS. CAUTION CP101 CD3800 F-3 D3802 W874 W043 W026 CP8001 R4203 OS2202 W813 R3800 D3808 D110 CME066A W209 D402 VR3800 D3824 R3803 SW2213 TP402 R3819 C3801 W148 W210 SW2215 R3801 W056 C642 W191 D111 W190 W189 D2201 D407 R432 C3004 C3030 D605 D602 C643 Q3002 W118 W192 D109 W840 W004 W195 W193 C401 R404 R405 D3004 C3023 D3002 C3820 R3830 W022 R3004 R3013 W051 W052 W053 D601 R650 W055 W859 W216 W050 C613 C610 C615 L101 W836 TP403 S802Y W123 W805 R3829 W003 D3829 W058 W122 W121 W196 SW2220 X101 W850 R623 C645 C624 W125 W124 W198 W197 R646 W127 W807 D3826 CP80 3A S801Y W044 R612 R431 C430 IC3002 Q3005 R3007 W047 R627 C625 W863 L604 W128 C621 W130 W200 W860 D102 W201 C618 W131 W129 W202 C604 C638 W203 C629 W827 W822 W132 C609 W832 R410 R406 R3010 W021 W020 D603 W046 S804Y C607 W098 W204 W100 W097 W096 W814 W812 C103 W173 W174 W843 W099 SW2214 W048 W101 W226 C606 R602 W105 C630 W102 W024 W023 W214 W890 W109 W107 C101 W106 D106 W181 W175 R117_1 SW2218 W112 W213 W108 D3001 W114 W115 W113 W185 W186 W182 C123 SW2216 D101 D105 Q402 CP802B CP803B X602 R3809 W176 W861 C3827 C627 R617 W187 W188 SW2217 R127 W225 R460 W851 W042 W846 R603 IC3001 D413 R412 HS3001 S801X D806 D804 R408 R433 S802X W871 W803 W819 D3003 D805 W218 Q403 W015 SW2223 D3006 Q3008 ATTENTION INFORMATION POUR SERVICE DES PIECE CRITIQUE. Q401 R444 R3009 W872 W873 HS402 R409 C3013 W879 W878 Q406 R401 D3005 Q805 D406 Q806 W880 W177 C418 Q804 D408 C3001_1 C626 SW2221 W090 W178 28 D409 CCE062A TP023 R806_1 SW2219 C4 C3028 01 J8 R807 D3825 R651 D416 CP806 TP024 W092 W184 W013 R456 R805 L401 C417 CP805 C341 R313 R802 C410 C129 R804_1 TP022 FB401_1 W012 Q405 R803 W172 W168 R447 R417 T401_1 W011 R424 IC353 R312 C340 C127 J2202 R422 W074 C802 W852 IC352 CP401 W841 C421 R402 S804X W077 W219 W156 W154 W151 W150 W152 W153 R429 D405 W078 R4282 J2203 C429 R407 W040 W804 10 W081 W079 W038 W825 W158 R3 W082 R403 D404 R418 W080 W083 W826 HS401 R415 R4281 R421 D411 W039 W916 W085 C406 D401 W159 J2204 IC401 R416_1 W086 D403 R411_1 W041 C407 C357 W160 VR402 C434 R413_3 R434_2 R414 CP302 W087 W161 R124 W166 W165 C2204 R2226 W088 W167 C405 J2201 C2201 R2225 F-4 . VOIR AU VERSO. C337 C332 C338 C339 C342 R131 Q3007 R2220 C631 IC103 C104 R101 1 Q3804 C138 R114 R120 R2217 R142 R106 R148 C109 R2219 C641 R4221 Q2201 23 R2216 R4201 C3012 C3016 C3007 IC199_1 R138 C110 R140 C111 R144 R149 R141 R157 R145 R639 R126 R109 34 IC 10 1 R125 R123 C124 R115 R628 R647 C117 C334 C333 C008 R4207 R4206 Q4203 R128 R113 C102 R110 C130_1 IC601 C107 C108 C633 Q104 R103 C605_1 R119 C632 C601_1 R616 R618 R619 R644 C616 C612 R611 Q4202 R4202 Q4204 C335 R305 C348 R308 R816 R813 C811 Q602 R809 R3008 C644_1 Q601 R641 C628 Q605 R607 R605 C608 R643 R610 R609 Q4206 C809 R815 C3003 C007 C004 C4205 C003 R4242 C001 C4215 C002 R4241 Q3003 R811 R3001 R3006 R3003 R3002 R3011 R3012 C3806 C4224 Q4201 R4210 R4216 R814 C810 CCE062A F-5 C3802 C3805 C3809 PRINTED CIRCUIT BOARDS AV/CRT (CHIP MOUNTED PARTS) SOLDER SIDE Q4205 R147 R143 R2214 R2201 R2215 12 Q101 R136 R2218 R420 R428 R2221 CME066A F-6 . PRINTED CIRCUIT BOARDS LOADING MOTOR (CHIP MOUNTED PARTS) SOLDER SIDE SOLDER SIDE SW1 LOADING MOTOR (INSERTED PARTS) CD2302 SW SOLDER SIDE SW2 D D0 0 CD2301 M2601 F-7 OR BLUE BL RE M2602 F-8 . 2 1.3 2.3 3.3 NC 3.3 0 3.3V 220 KA 6.8V 8 UNREG+3.3 3.3V 100 KA C4014 0.4 0 2.3 3.01 B 10 33 33 33 C4065 0.3 3.3 3.3 GND (GND.3 3.3 3.3 0 3.1 F 820 TP4019 2.0012 B JG023 MMZ1608R102CTFS2 B4009 JG022 MMZ1608R102CT 0.3 3.7K GND TP4009 C4029 0.3 3.3 BOOTSEL1 56 RAMADD(2) +-1% C4009_1 C4016 0.3 3.5X19 TP4013 0.3V 47 KA C4036 0.1 F C4088 B4016 MMZ1608R102CT +1.3V 100 KA C4083_1 F C4082 0.3 3.1 F ML TP4004 MC TP4006 MD TP4005 D1_2 D1_1 SYS_MUTE C4097 0.3 3.1 F 100 0.3 3.3 0 3.3 1.3 0.1 F SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0# 54 RAMADD(3) C4019 HD0 HA4 RD HA3 HA2 MEMCS0 HA1 HA0 53 RAMADD(4) 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3V SSCRXD TP4001 SSCTXD TP4002 C4059 100P CH 0.7K R4060 R4062 DUPTD0 JG008 C4002 R4061 JG007 DUPTD1 1SS355 1SS355 DUPRD1 R4052 D4007 JG006 D4006 JG005 1SS355 BOOT1 D4005 (DVD PCB) 3.1 F STBY_L C4031 3 0.2uH 0305 R4014 EN VCC2 VCC1 VO1 VO2 ADJ 1 2 3 5 6 7 DVD-H 2.3 3.3 3.8V RF OPU_A OPU_B OPU_C SPDL_SENSOPU_D VC OPU_F SPDL_SENS+ OPU_E DVD_LD CD_LD DVD/CDPD DVD/CDPD (VR_DVD) (VR_CD) DRVSB (MUTE-L) B4013 DVD/CD MMZ1608R102CT(DVD-L/CD-H) TOUT_SW TIN_SW TRAY_CLOSE B4012 MMZ1608R102CT C4057180P CH C40560.3 3.3 3.3 3.7K R4036 7 4.1 F C4024 0.7K 330 +-1% +-1% MIC_ON (PM1) REG+3.3 3.3 3.6 3.7K R4039 R4051 4.3 3.3 3.1 F 2 R4063 R4050 4.3 3.CON+3.3 3.3 3.3V 100 KA C4012 C4011_1 6.7K R4045 4.3 3.3 3.3 3.1 F HD11 HD3 HA19 205 DUPRD1 100 C4013 0.CON+5V TP4012 TP4011 TP4021 C4066 2.CON+5V C4096 C4020 DUPRD0 JG009 4.1 16V47 KA 0.1 F 11K C4003 SPINDLE_PWM 0.4 0.8 5 6 P.3 0 0 3.5 4.3 0 3.3 8 FROM/TO AUDIO/VIDEO 0.8 0 0 3.1 F 55 RAMADD(5) 0.8 3.CON+A5V P.3V 100 KA C4070 C4067_1 C4108_1220P CH 6.6 1.3 3.3 3.2 3.7K GND P.8 0 0.3 3.1 F C4017 0.3 3.3 3.CON+3.3 3.8V 9 GND(A) 10 SPDIF 11 SSCRXD 12 SSCTXD 13 3 3.3 3.3 3.1 1.7K 15K 4.1 HD12 WR HD4 207 SSCCLK GNDDACBS2 GNDDACP RSET C/B/U VDDDAC Y/R/V CVBS/C 160 A VDDDAC CVBS/G/Y 159 G Y/C 158 RFN GNDDACD GNDDACD 157 RFP GCLK XO VDDA RESET# GNDA GNDP VDDP IDGPCI/O(2) GPCI/O(31) DJTCK / ICGPCI/O(3) / VID(0) DJTO / GPCI/O(30) / VID(1) DJTDI / GPCI/O(29) / VID(2) DJTMS / GPCI/O(28) / VID(3) MPEG/MICON/DSP/RF_AMP IC VDDC GNDC IC4001 GPCI/O(27) ZR36862PQCG-B IDGPI/O(1) ICGPCI/O(2) GPCI/O(26) VDDP ICGPCI/O(1) GNDP HSYNC VSYNC AIN VDDP-A2 AMCLK 100 RAMDAT(14) GNDP-A2 101 GNDP ABCLK ALRCLK 102 RAMDAT(1) GPAI/O 103 RAMDAT(15) AOUT(0) 104 RAMDAT(0) AOUT(1) AOUT(2) SPDIF IDGPCI/O(0) ICGPCI/O(0) GNDP GPCI/O(20) VDDP 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101102103104 7 B4002 (120mA) MMZ1608R102CT C4052 C4010 208 SSCTXD C4018 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15 VDDDAC VDDAFERF B4001 MMZ1608R102CT (10mA) C4007 105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156 HA10 HD14 HA9 HD6 HA8 HD13 HD5 (W834) (AFEGND) 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 SSCRXD MEMCS(1) VDDP MEMAD(15) MEMAD(16) MEMAD(14) MEMAD(13) MEMAD(12) MEMDA(15) MEMAD(11) MEMDA(7) GNDP MEMAD(10) MEMDA(14) MEMAD(9) MEMDA(6) MEMAD(8) MEMDA(13) MEMDA(5) MEMAD(20) VDDP MEMDA(12) MEMWR# MEMDA(4) VDDC MEMDA(11) MEMDA(3) MEMAD(19) GNDC MEMDA(10) MEMAD(18) GNDP MEMDA(2) MEMAD(17) MEMDA(9) MEMAD(7) MEMDA(1) MEMAD(6) MEMDA(8) MEMAD(5) VDDP MEMDA(0) MEMAD(4) MEMRD# MEMAD(3) MEMAD(2) MEMCS(0)# MEMAD(1) MEMAD(0) GNDP VDD-IP VDDP 53 54 55 56 57 58 59 60 SYS_MUTE DVD-H DAC_VIDEO_C DAC_VIDEO_B ASDATA0 ABCLK ALRCLK AMCLK MD MC ML P-H/I-L RESET P.1 F 206 DUPTD1 R4059 0.1 1.3 0 3.3 0 3.3 NC 3.CON+5V W837 VDDPWM +1.3 3.3 1.3 3.3 0 3.1 HA15 HA16 HA14 HA13 HA12 HD15 HA11 HD7 0.3 3.1 F B4006 (250mA) 100 0.3 0 3.8 3.3 3.3 3.3V 47 KA 6.3 3.3V 0.3 3.01 P-H/I-L R4016 27MHz X4001 100GT02720 C4035 18PCH C4028 0.9V IC IC4003 BA33E00WHFP 4 CD4002 CU2D2202 (CP8001) 1 GND(D) W850 1 C4098 DVD/VR 130mm DVD COMBO 250mm TP4027 R4080 R4009 TP4015 TP4016 FROM/TO REGULATOR GND (D_GND) JG024 ASDATA1 ASDATA2 L4002 M_GND TP4008 TP4010 W842 TP4017 TP4018 R4024 4.3 3.3 3.3 3.3 0 3.3 1.027 B 0.0 3.1 0.8 JG004 1SS355 1SS355 1SS355 BOOT2 D4004 D4003 D4002 JG003 JG030 UNREG+3.001 B W836 NC C4023 C4078_1 1K BOOTSEL2 6.1 3.3 0 3.027 B SGND 11K SLED_PWM B4011 39K TRACK_PWM MMZ1608R102CT TRAY_OPEN MPEG/MICON/DSP SCHEMATIC DIAGRAM PCB130 DME060 2 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A G-1 B PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.7K 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 C4077 4 R4077 4.7K 6P CH 1M R4012 R4042 100 75 +-1% 75 +-1% R4002 75 +-1% R4003 R4005 75 +-1% R4004 C4034 1 6.8V JG002 IRRCV JG001 FPCSTRB P.A B C D E F G H 0.3 3.3 3.01 B C4080 C4090 10V 100 KA 2 F 47K TP4003 SD_D1 SD_D15 SD_D0 4 GND(M) P.3 3.3 3.3 0 3.3 1.CON+3.3 1.8V +3.3 3.3 0.CON+A5V 7 UNREG+3.4 0 0 2.3 0 3.3 3.8V 0.01 B C4030 100 C4084_1 R4072 R4019 R4020 R4021 6 DVD/CDPD DVD_LD CD_LD SPINDLE_PWM SLED_PWM TRACK_PWM FOCUS_PWM P.3 FROM/TO MOTOR DRIVE (D_GND) TRAY_OPEN TRAY_CLOSE HOME TOUT_SW TIN_SW DVD/CD DRVSB RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC SPDL_SENSSPDL_SENS+ 6.3 3.4 3.3 3.3 3.3 1.1 B C4027 0.CON+6V 0.3 3.3 2.1 C4025 UNREG+3.USE ONES DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES D E 1 ARE F G H G-2 .1 F C4015 R4070 6.1 F 0.3 1.1 F SD_D7 SD_D9 SD_D6 RAMCLK SD_D8 RAMWE# RAMDQM RAMRAS# RAMCAS# 0.3 0 0 3.3 3.8 3.7K 5 W5T29X7.3V 5 R4078 R4033 FROM/TO MEMORY 6 4.3 3.3 3.2 1.3 2.1 F C4075 P.3V VCC+6V RESET 6.5 2.8 0.3 3.3 3.3 3.3 0 0 0 0 3.3 3.3 3.1 F HOMEJG028 PM16 (MIC_DET) (DJTDO) I2C_CLK I2C_DAT 0.3V 47 KA C4068_1 RFINN RFINP 0.3 3.3 3.3 3.3V 47 KA C4069_1 DUPTD0 DUPRD0 PWMCO(0) IDGPCI/O(4) GPCI/O(46) VDDPWM PWMCO(4) GNDPWM PWMCO(3) PWMCO(2) SPINDLEPULSE SLEDPULSE VDD-IP ICGPI/O(7) ICGPI/O(6) GNDP IDGPCI/O(3) VDDP ICGPCI/O(5) ICGPCI/O(4) GNDC GPCI/O(32) VDDC AGND1 AGNDREF DVD_LD CD_LD DVD_MD CD_MD RESOUT VBGAP VC F K E AGND J D H C AVDD SVDD B AVDD1 SD_A1 SD_A7 SD_A0 SD_A4 SD_A3 SD_A5 SD_A2 SD_A6 W829 0.01 B IAMCLK IABCLK IALRCLK R4025 220 AMCLK R4026 R4027 220 ABCLK 220 ALRCLK R4058 220 ASDATA0 SSCCLK W806 RDY[I/O[0]] W808 M_GND TP4014 VCC+6V TP4020 L4001 P.1 F 0.3 3.7K C4008 MEMCS0 RD WR SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10 3 4.1 F C4086 0.3 3.3 3.1 F R4001 F HD2 HA17 HD9 HA7 HD1 HA6 HD8 HA5 MMZ1608R102CT C4053_1 HD10 HA18 B4005 (130mA) 0 0 1.3 3.3V 100 KA RAMRAS# RAMCAS# SD_BA0 RAMDQM RAMWE# RAMCLK NC R4008 C4022 R4064 R4054 1K R4053 61 62 63 64 65 66 DAC_VIDEO_C DAC_VIDEO_B 3.3 3.3 3.2 GND 8 4 4.3 3.4 3.3 3.CON+A5V P.1 F HOME TP4007 R4069 (ICETCK) (ICETDO) (MUTEC) (ICETMS) JG021 (PM11) 4.3 3.3V RAMADD(6) VDDP RAMADD(1) RAMADD(7) RAMADD(0) GNDP RAMADD(8) VDDC RAMADD(10) GNDC RAMADD(9) VDDP RAMADD(11) RAMCS(0)# RAMBA(1) RAMBA(0) GNDP RAMCS(1)# RAMRAS# RAMCAS# VDDP RAMWE# RAMDQM GNDPCLK PCLK VDDPCLK RAMDAT(8) GNDP RAMDAT(7) RAMDAT(9) RAMDAT(6) VDDP RAMDAT(10) RAMDAT(5) RAMDAT(11) GNDP RAMDAT(4) VDDC RAMDAT(12) GNDC RAMDAT(3) VDDP RAMDAT(13) RAMDAT(2) F 3.001 B C4033 JG029 DUPTD1 DUPRD1 DUPTD0 DUPRD0 FOCUS_PWM 3.3 0 3.3 3.3 1.3 0 3.7K 4.3 3.3 3.3 3.1 F C4004 R4022 B4018 MMZ1608R102CT TP4025 TP4026 R4043 10K +-1% 10K +-1% 0.8V 3 RDY(I/O(0))/RX R4081 TP4023 MMZ1608R102CT SD_D13 SD_D2 SD_D14 SD_D3 SD_D12 SD_D4 SD_D10 SD_D5 SD_D11 B 2 10V100 KA RDY[I/O[0]] C4026 SPDIF SPDIF MMZ1608R102CT 150 TP4022 GND(D) SSCCLK/TX C4100 10P CH 10V 100 KA R4071 B4010 TP4028 C4089 JG020 4 4.2 2.3 3.1 F RAMCS0# SD_BA0 SD_A9 SD_A10 SD_A8 R4018 4.3 0 0 3.3 3.3 0 3.001 B C4032 0.1 3.CON+3.D_GND) B4003 (250mA) (10mA) MMZ1608R102CT 0.01 B JG033 SSCRXD JG032 SSCTXD JG031 SSCCLK C4038 8 B4014 FS1 C4001 0.9K +-1% UNREG+3.3 1.1 2.7K 4. C THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.4 2.3 3.1 F C4072 C4071_1 6.2 0 3.3 3.3 3.7K 4.7K R4038 R4037 P.3 0 3.1 F TP4024 P.3V +1.3 3.3 0 3.3 3.1 F C4076 B C4101 C4081 0.8 3.3 3.3 3.3 3.3 1.9 3.001 B C4085 0.CON+5V 0. 4 RP# DQ5 19 HD9 3.3 SD_A10 3.8 A9 39 HD12 DQ6 A10 DQ13 38 0.3 18 1.5 3.6 DQ12 0 HA8 12 0.3 SD_D0 10 1.3 RAMCAS# 3.3 SD_BA0 3.3 20 1.7 /WE 3.3 RAMDQM 3.3 RAMRAS# 3.1 F 0.3V 100 KA C4063 6.3 15 HD8 0.3 44 3 0.6 HA6 1. D E 1 F G H G-4 .6 RD 2.7K 2.5 HA2 1.3 36 1.6 HA1 /CAS /RAS /CS BA A10/AP A0 A1 A2 A3 5 0 NC 1.3 SD_D7 VDDQ 3.3 R4041 A4 5 47K RAMCKE HA3 2.3 27 A4 21 OE# 22 A5 28 DQ0 A6 23 DQ8 A7 6 46 44 43 42 34 33 32 31 30 DQ1 A17 27 29 DQ9 24 R4040 B4007 MMZ1608R102CT A18 DQ9 6 LDQM 3.1 F C4106 C4074 0.3 DQ3 3.A B C D E F G H MEMORY SCHEMATIC DIAGRAM 8 8 (DVD PCB) FROM/TO MPEG/MICON/DSP HD0 1.8 SD_D15 43 HA14 5 0.3 SD_A2 3.1 F NC RAMDQM 3.3 RAMWE# 3.3 41 9 10 11 SD_D8 VSSQ 14 0.1 F A19 3.2 HA16 47 SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10 7 16M SDRAM IC4009 M12L16161A-7TG FLASH IC 8M IC4007 SST39VF1601-70-4C-EKE GND (D_GND) FROM AUDIO/VIDEO RESET 2 W854 2 MEMCS0 PCB130 DME060 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A G-3 B C NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.3 VDDQ 3.6 CKE 33 HA19 (W838) NC SD_A9 3.4 HA7 1.3 DQ5 SD_D11 VDDQ 3.1 F C4039 A0 A1 1 50 NC 0.1 F 3 6.3 SD_D6 3.3 VSS VDD 4 25 HD11 1.CON+3.9 WP# 3.3 3.3 RAMCS0# 3.7K 0 7 3.7 VDD 42 1 2 1.3 UDQM RAMCLK 2.5 3.3 R4048 0 4.1 F C4044 6.3 3.3 29 A3 DQ8 A6 SD_A5 3.1 F 13 3.3 23 HD10 DQ4 3.1 F A9 SD_A8 3.2 A11 DQ13 39 HD6 DQ7 3.3 HA4 35 HA18 CLK 34 1.3 11 C4040 14 C4062 41 HD4 1.3V 100 KA C4021 0.3V 3 HD15 45 0 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15 4 VCCQ A15 VSS 0.3 WE# DQ10 3.9 A13 DQ1 26 HD7 GND DQ14 47 HA12 3.3 0.6 A8 40 0.3 0.01 B B4008 MMZ1608R102CT P.0 6 48 HA15 7 A14 1.7 C4109 MEMCS0 RD WR 3.6 HA5 1.3 SD_A0 3.1 F RAMRAS# RAMCAS# SD_BA0 RAMDQM RAMWE# RAMCLK RAMCKE HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 5 3.3 DQ4 SD_D3 C4045 24 HD3 1.1 DQ11 3.3 13 SD_D12 0.3V 220 KA C4099 (W809) 0.1 DQ3 SD_D9 SD_D5 16 1.3 SD_A3 C4047 0.3 A16 0 8 C4064 SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0# 6 1.3 32 15 16 17 18 19 20 2 3 4 5 3.3 31 A2 VDDQ A8 SD_A7 3.6 FLASHCS A19 25 0 DQ10 VSSQ 0 4.6 3.7 37 HD5 36 0.3 C4041 RESET 0.6 35 HD13 DQ14 C4050 12 HA10 DQ2 40 1.3 30 CE# DQ7 A7 SD_A6 3.1 F 1.4 VPP 0 17 HD1 WR 0.3 A12 VSSQ 37 HD14 DQ15 48 2.01 B C4095 0.1 F 22 1.6 3.3 SD_D13 49 HA11 VSSQ 38 1.6 A20 SD_D10 DQ11 7 SD_D2 3.3 8 1.3 SD_A1 3.3 C4046 0.5 HA0 DQ2 26 2.3 DQ0 46 4 1.3 3.2 0 NC 0 VCC HA19 SD_D4 21 HD2 (W837) 0.7 HA17 1.5 SD_D14 DQ15 45 HA13 3.3 28 GND DQ6 A5 SD_A4 3.3 SD_D1 9 HA9 DQ12 3. 1 6 SPINDLE_PWM TP2322 E 0.8 27K OPEN R2341 R2321 LD+ 3 6.7K TP2305 P.9 2SA2048 220 4.9 TP2321 F 21 JG013 0 6.2 MOT_SPDL+ 9 2.+3.5 1K 20 OPU_A 3.CON+3.8 JG019 R2310 4 MOT_LD+ 6.3V 47 KA 7 PCB130 DME060 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A G-5 B THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.2 MOT_SLED- MOT_SPDL- MOT_SPDL+ FO- FO+ TR- TR+ MOT_LD+ MOT_LD- 2 R2358 120 +-1% 100 B R2302 C2365 0.1 R2338 100 4 0.6 26 VCCS VO_OP VD2+ 13 3.1 3.7K R2327 19 6.8 1.3V B2303 VCONT MON(COM) (D_GND) MMZ1608R102CT REV GND(CD) 13 R2306 VR DVD Q2303 KTC3875S_Y_RTK 0 82 12 16 C2332 R2359 B2304 7 TOUT_SW TIN_SW MMZ1608R102CT 6.7K R2351 R2350 B2305 TP2304 4.6 3.6 39 TP2312 LIMIT SW 4 40 NC 1 0 HOME 5 0 NC 1.7K TP2308 TP2309 5 MMZ1608R102CT R2313 C2341_1 MMZ1608R102CT 75K B2302 0.6 1.8 R2332 4.5 0 32 C2306 SP1- F R2336 0 NC 0.7K 4.6 41 VD4- FWD C2360 100P CH 100P CH 100P CH 100P CH C2358 C2359 C2357 TP2306 R2349 3.1 B R2304 2.7 SLED_PWM 220 1.8 28 R2325 3 6.6 29 R2329 SP1+ 8 2.0 20 0 10K R2337 TP2316 VIN 1 21 1.3V 47 KA CDLD VR/CD RF_A5V S-GND VOL(CD) JG018 C2327_1 LD(CD) 11 JG017 82 DVDLD LD(DVD) 10 R2356 JG056 C2326 F VR/DVD W843 GND(DVD) 1K 8 NC R2355 VOL(DVD) 33 NC(SW) 7 R2360 6 C2309 DVD/CDPD MON(DVD) 9 6 FO+ F+ 5 1B 4 (RF_GND) 6.7K 1.3K 3.022 B C2302 R2303 C2304 0.5 0 27 NC VIN-OP 12 0 VD1- VIN+OP 11 0 VD2- REG-IN PGND1 REG-OUT NC PGND2 VREF-OUT VD3- VD3+ 10 2.1 B 4.6 30 C2314_1 1 7 2.0 0 34 TP2315 SLD+ 2 35 TP2314 3 MOT_SLED+ 36 TP2313 100 MOT_SLED- 5 37 VCC1 3 2 0 0 NC 6.3V 47 KA 4.0 23 NC 24 VIN2- VIN3- VD1+ 15 2.0 44 VREF-IN 0 MMZ1608R102CT MOTOR DRIVE IC IC2301 LA6565VR-TLM-E 4.6 4 22 1.A B C D E F G H MOTOR DRIVE SCHEMATIC DIAGRAM 8 8 DVD_LD DVD/CD CD_LD FROM/TO MPEG/MICON/DSP VC DVD/CDPD (VR_CD/VR_DVD) (DVD PCB) DVD/CD DVD_LD CD_LD DVD/CDPD RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC HOME GND GND FROM/TO LOADER CP2301 LD07T2-24ND-03 1 T- TR- 2 T+ TR+ 3 F- FO- C2318 0.3V 47 KA 0.1 R2348 MUTE1 DVD_CD VCC2 DVD/CD R2308 DVD/CDPD 14 P.6K 1 C2348 R2353 TOUT_SW 100 R2352 TIN_SW SPDL_SENSTP2323 R2326 GND(D) SPDL_SENS+ VC2 TP2319 2 6.1 43 C2301 6 B2305 short --.5 0 NC 1.USE ONES NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.7 0 NC 1.3V 4.5 1.0 0.1 B 0.1 B TP2318 1 5 TRAY_OPEN VIN1+A CLOSE TRAY_CLOSE TP2324 5. C DESCRIBED IN PARTS LIST ONLY D E ARE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F 1 G H G-6 .7K MOT_LD- 10K C2328_1 TP2303 LD- 5 R2320 4.1 F C2342 C2347 C2346_1 6.8 R2346 10K 15 VR DVD Q2305 KTC3875S_Y_RTK 0.7 NC 19 JG011 0 F A OPU_C DRVSB R2318 0.2 C2305 D2304 1SS355 0.1 TO LOADER 6.2K 6.6 1.3K MUTE234 D OPU_B JG010 0.3V 100 KA CD LD CTL 1.1 F C2315 M_GND B2301 JG012 C2331 NC GND(PDIC) 1.1 F MOT_SPDL- 6 0.6 1.3K R2335 4.1 C2310_1 10V 100 KA 1K C2307 JG057 2 JG058 MOT_SLED+ R2323 C2303 R2357 D2303 1SS355 2.001 B 6.2 C2313 10V 100 KA R2328 1.1 B 0.8K 0.5 R2340 4.3K VIN4- VCC 23 JG015 DVD/CD 0 Q2304 KTC3875S_Y_RTK FOCUS_PWM VLD- 22 OPU_D TP2307 R2347 0.6 33 TP2317 R2330 6.6 NC 31 0.6 1K VIN2+ 18 VIN1-A 17 0 NC 6.CON+3.3V 100 KA VLD+ 24 OPU_E VCC+6V R2339 C2340_1 R2307 Vref OPU_F JG014 3.7K R2342 FROM/TO LOADER 3 4.3V 47 KA 390 10K R2334 R2319 TP2320 33K R2309 100 +-1% 1K R2324 16 2.0 R2333 Q2302 3.7K VIN4 CP2302 00_6232_005_006_800+ OPU_VREF R2305 F TRACK_PWM VD4+ 0.1 42 TP2310 SW(GND) 3.1 F C2343_1 0.1 B 18 RF JG040 C2329_1 C 17 JG016 DVD LD CTL Q2301 2SA1036K R2301 RF 6.6 25 VIN2 VIN3 14 1.0 NC 38 TP2311 SLD- 4 0 NC 1.CON+A5V TRACK_PWM FOCUS_PWM P.1 B 0.3V CP2303 00_6232_006_006_800+ 0. 1 AMCLK 3.4 13 0 1.9 AGND STEREO DAC IC IC8102 PCM1753DBQR C8121 7 9 0 2 2.0mm pitch) 1 B CD8101 2F0C1602 3 NC 3 CP8101_3 IMSA-9604S-12F BCK 1 SCK DATA ML LRCK 1.3 1.3 3 ML 2.6 2 EXT_MUTE 12 DVD RESET 11 ZERO 10 AUDIO-R 9 GND 8 AUDIO-L 7 GND 6 Y 5 GND C 4 GND 2 CVBS 1 3 2 ALRCLK ASDATA0 14 15 16 0 3.1 TO MEMORY F C8120 (D_GND) 4 MMZ1608R102CT C8114 R8113 1 B C8125 470 6 1 B C8113 R8112 1 B C8126 470 FROM/TO REGULATOR 7 FFC(1.A B C D E F G H AUDIO/VIDEO SCHEMATIC DIAGRAM (DVD PCB) 8 8 7 7 FROM/TO MPEG/MICON/DSP C8106 C8104 1uH 0305 C8108 DAC_VIDEO_B C8109 150P CH C8107 W819 12P CH L8103 1uH 0305 Y/R/V DAC_B_VIDEO 6 10 150P CH RESET MC MD ML AMCLK ABCLK ALRCLK ASDATA0 6 12P CH L8102 150P CH P.3V 100 KA 0.4 PCB130 DME060 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A G-7 B C NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.3 VCOM VOUTL 6 ZERO 6.001 B C8119_1 6.CON+5V DAC_C_VIDEO 9 150P CH DAC_VIDEO_C DAC_VIDEO_C DAC_VIDEO_B W818 C/B/U C8105 TP8101 P-H/I-L TP8102 P-H/I-L SYS_MUTE GND TP8103 NC TP8105 TP8104 TP8106 RESET ZERO NC NC D8111 W826 TP8107 1SS355 5 5 TP8108 W824 R_AUDIO TP8109 L_AUDIO TP8110 RESET DAC_C_VIDEO TP8113 DAC_D_DVD_VIDEO TP8114 D8112 1SS355 C8122 TP8112 SYS_MUTE B8103 4 DAC_B_VIDEO TP8111 0.7 ABCLK 0 NC 1.5 VOUTR 8 MD 2.3V 100 KA 4. D 1 E F G H G-8 .6 MC 12 DGND 11 4 MD 10 0 MC ZEROL/NA VDD 5 ZEROR/ZEROA VCC 3. 0 F 0.2K +-1% C3002 R3002 4.CON+9V AT+5V 5.9 R3007 CP8002(CP8101_3) IMSA-9604S-12C 10 POWER_ON_H R3010 100 1/4W FROM/TO AUDIO/VIDEO GND 1K UNREG+3.CON+5V AT+5V POWER_ON_H POWER_ON_H 4.6 R3009 D3003 1 P.1 B C3016 SPDIF DVD_C 9 11.CON+5V_REG IC3002 KIA278R05PI 7 IN OUT 1 2 FROM POWER 5.5K R3012 16V 220 YK B C3004 C3003 0.9K +-1% 11E1-EIC 0 GND(D) S802Y 2 10V 2200 YK C3010 CP8001(CD4002) A2001WV2-13P 1 GND(D) 10V 2200 YK FROM/TO MPEG/MICON/DSP P.1 B 4 RDY(I/O(0))/RX 5 4 C3011 SSCCLK/TX DVD_CLK 3 R3001 3.CON+5V (DVD) 11.1 C3017 HS3001 763WSA0029 P.8V 10 GND(A) 11 SPDIF 12 SSCRXD DVD_DATA_OUT 13 SSCTXD DVD_DATA_IN C3023 C3030 25V 10 KA 4 12.1 C3007 0.CON+6V 7 P.CON+9V UNREG+12V 6 MOTOR+6V_REG IC3001 BA00BC0WT-V5 UNREG+8V GND P.6 C GND 0 TO IN/OUT DRIVER Q3008 KTC3203_Y DVD_A_OUT_L P.USE ONES E CAUTION: DIGITAL TRANSISTOR 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES D ARE F G H G-10 .8 DRIVER Q3001 KTA1281_Y R3015 1 UNREG+8V D3004 MOTOR+B[+6V] 1N4002-PAN 2.CON+5V W859 UNREG+8V 8.8V 10K 11 1.7 D3005 GND 2 OUT 3 7.CON+A5V 8 UNREG+3.6 FROM/TO MICON/TUNER DVD_RESET DRIVER Q3002 KTA1281_Y NC 1K 1/4W R3004 0 DVD_CLK DVD_RDY DVD_DATA_OUT DVD_DATA_IN P.8V 9 UNREG+3.ON SW Q3003 KRC102SRTK D3006 POWER_ON_H R3003 2.0 1N4002-PAN TO CHROMA DVD_Y DVD_C P.2 6 UNREG+3.6 MTZJ5.CON+5V P.7K +-1% 10V 2200 YK C3001_1 10V 470 YK DVD_RDY GND(M) P.A B C D E F G H REGULATOR SCHEMATIC DIAGRAM 8 8 (AV PCB) P.6 6 1N4002-PAN 16V 100 YK C3012 0.0 3.6 5.2 3W 4.8V 1.2 10K 1/4W FB R3017 IN 1K 1/4W SW 5 1.CON+5V 16V 100 YK W890 W844 NC W889 1K 1/4W TO SOUND AMP NC GND P.3 4.6B-EIC 2 9. C THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.CON+5V(DVD) 5.9 NC R3011 33 1/2W R3008 12 R3006 UNREG+12V UNREG+12V 3 5 9.ON SW Q3007 KRC102SRTK 8 Y DVD_Y 7 GND 6 AUDIO-L 5 GND 4 AUDIO-R DVD_A_OUT_R 3 ZERO ZERO 2 DVD RESET 3 P.5 0 4 6.CON+8V 0 5 D3001 2 DVD_A_OUT_R ZERO PCBD20 CME066 1 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE A G-9 B PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.0 AT+5V SPDIF C3013 DVD_A_OUT_L 10V 100 YK EXT_MUTE 25V 10 KA 220 1/2W DVD_RESET C3028 UNREG+12V P.8 R3013 UNREG+5V UNREG+5V POWER_ON_H 1.5K P.CON+9V DRIVER Q3005 KTC3209_Y MTZJ10B-EIC D3002 12.0 GND SW 3 4 0 7 2.5 R3005 5. 7K OSD_B R141 OSD_G R145 2.6 4.7 PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE 6 5.2 VSS 42 5.2 3 30 OSD B VOLUME PWM MICON IC 0 IC101 OEC6087ANC PROTECT 4.1 31 REMOCON SD 34 32 VIDEO IN1 5.7K OSD_R 2. 4.KEY2 PROTECT DVD_RESET A_MUTE1 21.7 KA 0 E1 B C110 1SS133 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.2 POWER_FAIL D102 MTZJ5.SDA 35.9 4.5 8 0 0 32.8 NC TV POWER 0 DVD POWER DVD RESET 0.CON+5V 4.0 0 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE R128 VOL_PWM1 MUTE SW 68K1/4W Q101 KTC3875S_Y_RTK 0.3V 220 KA 0 0 0.8 1.056 C007 POWER_ON_H 100 1/4W R003 SDA SCL R149 KEY_A FROM/TO CHROMA B 4.01 L001 NC W812 5.1 H CONTROL VD 0 0 NC 5 FSC_OUT W860 0 SDA RESET AV1 0 17 39 40 41 IIC BUS OFF VIDEO_OUT 3.1 NC 0 FROM/TO IN/OUT 0 NC SCL I2C_OFF C003 100P CH W828 KEY_B 0.H-SYNC 43.3 12 36 3.5 SDA B R148 C111 20 TUNER_AUDIO R140 0.1 KTA1504S_Y_RTK 4.KEY1 13.6 4.1 B C104 H_CONTROL 0.1 OSD R VDD 43 0 0 16 38 NC 0 15 0 NC 2.23 1SS133 2 3 1 17 VIDEO OUT 16 IF OUT 15 BT 14 SIF OUT 12 AFT OUT 11 DATA 9 +B 10 CLOCK 8 FSC IN 4.7K REMOCON AFT R004 100 1/4W W823 100P CH C004 C006 10V 100 YK P.3 VIDEO_OUT RESET IC IC103 PST3231NR 7 NC 5 H 21 18 0 0.2 G 19 4 (AV PCB) 3 8 TU001 MICON /TUNER SCHEMATIC DIAGRAM F AUDIO OUT E 13 D 2 C 1 B 115-V-KA35ARE A R144 100 2.2 NC 7 5 NC 0 B NC 0 0.7K TUNER_AUDIO B 0.7K ST_BY_HI VOL_PWM1 POWER_ON_H 9 R109 4.2K D105 1SS133 29 34.7 W814 GND SDA IN FSC_OUT R119 OUT 3.0 5 0.1 5.6 R136 R138 0 D110 G-11 10V100 YK C119 C117 0.NC 4 TUNER_VIDEO 26 R142 23 4.1 0 C002 100uH 0607 NC 0 W818 NC 0 NC 4 0.01 B R147 100 TO SOUND AMP 100 R143 I2C_OFF H_CONTROL KEY_B KEY_A AFT R117_11M 1/4W P.3 4.7 35 4.7K R157 4.1 NC 5.6 0 SCL B C108 0.1 HD FROM/TO DEFLECTION 0 5.1 F 5.1 5.7K POWER FAIL OSD G 12.7K 0 5 6 7 8 5.7 5.1 13 37 VIDEO IN2 2.2 10K SW Q104 4.1 FROM/TO POWER ST_BY_HI GND FROM/TO REGULATOR DVD_RESET R106 4.8 NC 4.7 NC C008 0.CON+5V 1SS133 1 3 AT+5V DVD_RDY E0_LEAK DVD_DATA_OUT DVD_CLK POWER_ON_H DVD_CLK DVD_RDY DVD_DATA_OUT DVD_DATA_IN D109 1SS133 D111 4 POWER_FAIL R120 AFT E0 LEAK IN X-RAY IN DVD DATA OUT DVD CLOCK 0 10 2.OSD Y/BLK 22.7K R115 10K R103 10K R101 1SS133 4.VSS 3 2 1 3.1 4.7K R114 C138 0.001 100P CH C130_1 4.1 F A B C D 100K VOL_PWM R124 4 3 0 F C129 47K R131 2 PCBD20 CME066 1 0 THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.7K 25 SDA SCL SYNC_VIDEO XIN TEST OVSS OVDD V-SYNC 20 19 18 14 11 0 5.1 10V 33 KA C101 C124 5 6 OSD_Y G H G-12 .TV MUTE 44.6B-EIC 3 REMOCON R123 2 SCL 1 5.0 0.7K R110 D101 6 X101 W863 CSTLS16M0X53-A0 0 10K 5.USE ONES ARE 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E 0 E0 2 0 C123 VCC 8 100 C127 47K 7 MODE SCL E2 SDA VSS MEMORY IC IC199_1 AT24C04N-10SU-2.1 B C107 0.1 E0_LEAK POWER_ON_H X-RAY R126 4.7K DVD_DATA_IN 2 0 NC 0 +30V SCL XOUT DVD DATA IN DVD RDY STANDBY HI R113 4.1 F TUNER_VIDEO C001 +30V 7 4.1 50V 10 KA POWER_ON_H1 50V 1 YK A_MUTE1 POWER_ON_H 50V 4.7K 25 22 26 21 27 1/4W R127 PROTECT 28 2.7K 24 4.1 4.7K 270P CH 56uH L101 24 C109 R125 W805 22 D106 4.01 B C103 C102 6.0 44 0.1 4 33 3. NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE B C D PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.8 0 + 4.2 0.1 B 5 6 7 3 2 4.1 C338 SOUND AMP IC IC353 AN7513 6 25V 2200 YK 6 - - 3.3 C339 0 0.0 C342 0 0.6 SOUND AMP IC IC352 AN7513 GND C341 50V 1 KA C340 50V 1 KA C357 B C335 0.0 7.0 8 3.6 8 R310 SOUND+B 3 0 FROM POWER 2 0.3 4.0 4 1.A B C D E F G H SOUND AMP SCHEMATIC DIAGRAM (AV PCB) 8 8 FROM MICON/TUNER VOL_PWM POWER_ON_H1 7 4.8 SOUND_GND 1 3W 1 2.1 B 5 6 + 7 1.USE ONES F 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E ARE G H G-14 .6 4 7 330P CH FROM CHROMA 5 SW_A_OUT_L SW_A_OUT_R 51 R312 R305 18K 1/4W 10K 36 5 35 R313 50 C348 W852 R308 330P CH 18K 1/4W 10K TO SPEAKER 4 CP302 213213102W1 C337 C332 470P 470P CH CD302 CU12414A SP OUT R+ 1 1 SOUND GND 2 2 8 OHM CP301 C334 470P 4 SP352 S08F52 CH 470P CD301 CU12414A 213213102W1 C333 3 R CH SPEAKER CH SP OUT L+ 1 1 SOUND GND 2 2 L CH SPEAKER SP351 S08F52 CH 3 8 OHM FROM/TO IN/OUT SP_OUT_L SP_OUT_R SP_OUT_R2 SP_OUT_L2 SOUND_GND 2 2 PCBD20 CME066 1 A G-13 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.6 7. 5K FROM/TO CHROMA VOL UP KEY_A SW2218 EVQ21505R GND H 2 NC 1 3 E RED 5 1 5 4 3 2 7 P.8 3.6K SKIP REW R2221 2.3K MUTE SW Q4202 DTA143EKA MUTE SW Q4206 KRC103SRTK 4.9 6 NC NC 7 NC 8 VIDEO OUT 9 3 39 0 R4202 NC NC 5.1 SP_OUT_R B4201 H 68 R4242 C4204 FROM/TO POWER 10V 100 YK C4205 VIDEO_OUT 0.6 FRONT_VIDEO COAXIAL J4201 MSP-251V-05NI-FE-LF D AUDIO DRIVER Q4201 KTC3875S_Y_RTK FRONT AUDIO JACK J2203 MTJ-032-05A-32-FE FRONT_VIDEO 4.6 ZERO SOUND_GND SP_OUT_L2 0 DVD_A_OUT_R 0 3.0 3 GND POWER_ON_H 5.8 1K MUTE SW 0 Q4204 KTC3875S_Y_RTK W834 38 0 SP_OUT_R2 R4201 0.0 B SP_OUT_L 16V 220 YK C2204 2 0.7 0 MUTE SW Q4205 KRC104SRTK 37 1.5K 6 GND NC H 2 1 NC 3 E NC H 2 1 NC 3 E WHITE YELLOW FRONT AUDIO JACK J2204 MTJ-032-05A-31-FE FRONT VIDEO JACK J2202 MTJ-032-05A-30-FE 16V 220 YK R2225 W820 R4221 R4210 3.8 2 2 1K 0 MUTE SW Q4203 KTC3875S_Y_RTK PCBD20 CME066 1 A G-15 NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.CON+9V DVD_A_OUT_R2 DVD_A_OUT_L2 FROM/TO MICON/TUNER 4 VIDEO_OUT 4 TEST POINT CP101 A2001WV2-9P SCL SDA REMOCON I2C_OFF GND 1 I2C SCL 2 I2C SDA 3 I2C OFF 4 P.CON+9V SPDIF DVD_A_OUT_L DVD_A_OUT_R ZERO HEADPHONE_JACK J2201 MSJ-2000_AG KEY_A KEY_B POWER_ON_H SCL SDA I2C_OFF P. NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE B C PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.USE ONES D ARE CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E F G H G-16 .3K C4224 330P CH R2226 C2201 SP_OUT_L2 82 1/4W E W5RH3.2 C4215 82 1/4W R4216 SP_OUT_R2 1 1.2K 1/4W SW2220 EVQ21505R 100 1/4W 100 1/4W R4205 DVD_A_OUT_R2 VOL DOWN R2217 820 W819 DVD_A_OUT_L2 5 R4282 FRONT_A_IN_L 100K JACK_AUDIO_R 0305 W803 220 JACK_AUDIO_L 100uH R4241 6 R2215 R4281 FRONT_A_IN_R 1.7K 1/4W R4204_1 DVD_A_OUT_L 5 NC 0.022 B 1.7 SP_OUT_L SP_OUT_R 0.B C D E F IN/OUT SCHEMATIC DIAGRAM G D2201 AT+5V R2201 (AV PCB) 8 H 220 LTL-1CHEE-002A A OS2202 8 ROM-N3138SR 1 Vout 2 B+ 5.CON+9V 3 W821 3.0 0 SOUND_GND SKIP FF PLAY 7 SW2223 EVQ21505R 5.0 R4207 10K R4206 FROM/TO SOUND AMP 4.5X5X1.CON+5V 6 FROM/TO REGULATOR AT+5V P.9 2.5K SW2217 EVQ21505R OPEN/CLOSE CH UP SW2216 EVQ21505R SW2213 EVQ21505R 1K POWER ON/OFF R2216 820 SW2214 EVQ21505R C4201 W825 100 1/4W R2214 CH DOWN R4203 16V 47 YK W804 REMOCON AT+5V 7 SW Q2201 KRC103SRTK KEY_B L4202 R2219 1K 1.7K SW2221 EVQ21505R R2220 SW2219 EVQ21505R STOP SW2215 EVQ21505R R2218 1. 9 1N4002-PAN 1 1.6K +-1% 35V 470 MHE W851 MTZJ5.01 MMTS R409 22K 1/4W W841 56K 1/2W R405 56K 1/2W D408 MTZJ33B-EIC R404 T401_1 STP-03Q24 3 FB401_1 BSC23-N0168 COL VIDEO 6 0 2 250V 22 YK X-RAY +30V 1K 1/2W C434 1N4002-PAN E0_LEAK 110. D E PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE PCBD20 CME066 THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.POSI VR402 2.22 MKT R418 R401 2.2K METAL R417 MTZJ33B-EIC MTZJ33B-EIC 220 L401 5 1 R402 D405 1N4002-PAN 2 1 0 R447 W916 3 NC C431 D406 330 2W 4 272.8 2W 3 (CP803B) 3 GND 2 HEATER 1 W836 R453 2 2 150K 1/2W NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.2 F S B+ 0 9 NC 0 6 HV NC 2 4 14.0068 PHE Vcc NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.8 3.8B-EIC FROM POWER 5.USE ONES 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F ARE G H G-18 .7 NC FOCUS 1N4937-PAN 0 9 10 8 6 11 100V 0.7 3W CP803A B2013H02-4P 180V C402 100V 22 YK TP403 HEATER 1SS133 39K 1/4W +-1% C439 500V 56P SL R423 1.25KV 0.7 1/2W S804X AFC HS401 763WAA0237 560 1/2W R422 560 1/2W D403 D404 ACL C407 R414 C405 H_OUT 25V 2200 YK V_RANP_FB CP401 A1561WV2-A5P 5 43 W826 27K 1/4W +-1% R434_2 R411_1 1/4W 18K 1/4W +-1% R424 50V 1 YK 1K 1/4W 4.9 1/2W R467 1 R407 UNREG+12V R408 +B GND 1N4937-PAN D413 R431 1 1W 500V 0.0 2SA1624 HEATER 0 10 FROM/TO CRT 50V 22 YK H-DRIVE Q405 KTC3227_Y ABL GND R430 0 R456 0 AFC 6 44 133.OUTPUT IC IC401 LA78040N-E 8 (AV PCB) THERMAL PROTECTION AMP + PUMP UP GND 4 6 12.0 100V 0.0 GND R G B FROM/TO CRT D411 SW Q402 2SC2909 0 5 2.8 8 V801 A51AEZ90X23 GND 11 33K 1/2W 1 390 1/2W SW Q403 2SA1371 133.0022 B MTZJ6.9 100K 1/4W R432 R420 0.3K 560 R413_3 12K 1/4W +-1% FROM/TO CHROMA 6 7 FROM/TO DY 1/4W C406 5 0 35V 100 MHE 1.1B-EIC 1W 2.3 1K R403 D401 7 3 25.001 B C430 C423_1 C429 SCREEN R429 1 D402 C421 R450 1N4937-PAN R444 5.3 HS402 763WSA0029 133.3 250V 0.47 PMS C422 4 C428 C417 100V 0.OUTPUT Q406 2SC5885 247.6 1.9 7 24.A B 8 C D E F G H DEFLECTION SCHEMATIC DIAGRAM V.2 E12 NC 4 0 E25 3 NC 0 0 2 10K 1/4W 3 7 CD801_1 CU823001 (CP805) R433 CURRENT DET.6K 1/4W 5 5 7 1 8 4 D410 47K 1/4W R412 47K 1/4W R406 C410 100V 10 YK 25V 10 KA C401 10K R428 10K D416 135.47 MKT R460 0 100 1/4W C418 H. NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE A G-17 TO CRT 4 R445 W840 10K 1/4W 1 180V NC TP402 C432 R410 D407 1SS133 D409 B C 1 500V 0.5 250V 2.7K 1/4W +-1% R416_1 V_OUT 3.7mH 100 1/2W 0909 2 3.4 2W FROM/TO MICON/TUNER POWER_ON_H 1/2W R421 V.6 -0. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.2 MHE 4.7 1/2W R415 2. Q401 0 135. 38 7.OUT 4 R.7K 1/4W R802 GREEN OUT Q805 2SC4217 2.8 15K 2W 5 W880 4.96 6.A B C D E F G H FROM CHROMA 8 8 (CP802A) CP802B B2013H02-6P 1 GND 3 G.OUT D806 D805 FROM DEFLECTION 7 1SS133 CLAMP_OFF 1SS133 6 D804 (CRT PCB) CLAMP 2 1SS133 CRT SCHEMATIC DIAGRAM 7 HEATER 2 GND 3 R814 4. C D THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.6 6.OUT 5 B.38 122.38 125.94 15K 2W R803 7.7K CP803B(CP803A) B2013H02-4P 4 4 FOCUS C802 3 2KV 0.2 UM4 BT001 0 MNAAA(R03) PCB110 CCE062 UM4 BT002 MNAAA(R03) BL001 HPN-01 PCBD20 CME066 1 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE A G-19 B PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.95 45 5 127.USE ONES F 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E ARE G H G-20 .7K 1/4W TP022 6.001 B SCREEN CP806 3 ACCESSORY 12 10 TM101 F 0 0 2 0 4 6 117 5 7 0 CRT SOCKET J801 ISHS53S 1 8 121 2 NC 9 0 11 119 6.1 BLUE OUT Q804 2SC4217 W846 560P CH C810 7.7K 1/4W TP024 TP023 2.7K R816 390 R815 560P CH C809 R804_1 R805 15K 2W 46 R806_1 R807 RED OUT Q806 2SC4217 47 2.7K C811 GND 6 W873 W872 680P CH 2 W861 GND 390 W879 W871 CP805 (CD801_1) (CP805) A2361WV2-2P 1 R809 FROM/TO DEFLECTION R813 180V 180V W878 6 R811 NC 4 390 1 4. 0047 KX MTZJ5.USE ONES N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES CONTINUED PROTECTION AGAINST FIRE HAZARD.0 10 D3814 1K 1/4W 3.001 B 1SS133 R3800 POWER_FAIL 16V 1000 MHE 4.3 SOUND+B D3819 1.01 0.27 6.6B 4.2 12V P3 1 21DQ09N C3823 5 1SS133 D3829 C3805 1/4W 5 GND D3820 135V 135 14 16.4 0 W802 D3807 1N4937-PAN 50V 10 MHE 6.5M 1/2W BLACK S3801 BLACK C3801 WHITE S3802 WHITE 275V 0.3A125V R3829 D3824 1 1.012 B 6.3A 125V(F3800).1 168 W4BRH3.7M 1/2W +-10% C3827 3W 25V 2200 MHE 1 2 R3831 100 1/4W PCBD20 CME066 6.001 B 5W 21DQ09N D3817 D3825 R3830 25V 2200 MHE 3 C3812 D3816 4 C3810 200V 470 UP R3817_1 D3809 R3803 F3800 6.001 R GND R3828 W833 1 COIL.4 6 168 HG R3821 C3814 1/2W R3812 330 12 49 0 SG 2 R3815 13.047 MMTS 1/4W W813 UNREG+12V W874 P1 16.2M 1/2W B3800 R3820 500V 0.7K +-1% S 0 5V 8 168 C3807 3 2 1 FEED BACK IC3800 PS2561AL1-1-V(W) +B ADJ VR3800 470 METAL ST_BY_HI 4.4 Q3800 KTC3198 GND 25V1000 MHE R3826 0.7 SB 7 168 HS3800 763WAAA117 TO CHROMA 4.3A 125V UNE PROTECTION CONTINUE LES RISQUES D’INCEIE ATTENTION :POUR N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.9B-EIC 250V 0.01 B S801Y 1N4937-PAN UNREG+5V 14.3A 125V 6.2M 1/2W 7.LINE FILTER L3801 SS26V-R120220 RM11C-EIC C3815 C3820 C3822 TO REGULATOR 13 UNREG+12V 1W LG 3 P4 0 0 15 UNREG+8V GND GND 0 16 FROM/TO IN/OUT 8.01 C3806 D3831 MTZJ3.3A 125V(F3800).9K 1/4W 56K 1/2W R3801 R3802 P2 10 1/4W 0.3 BUFFER Q3802 KTC3203_Y R3818 3301/4W MTZJ18B-EIC D3804 R3809 100 1/4W 1/4W 330 R3804 R3805 MTZJ3.8 D3801 R3833 330 B 4 100V0.3 SOUND_GND 50V 10 YK D3815 D3810 FH3801 EYF-52BCY C3809 21DQ09N T3800 81300034 5 3 B TO SOUND AMP 1K 1/4W MTZJ12B-EIC GND W808 FH3800 EYF-52BCY 500V 0.0X2 D 240 330 4 1. CAUTION :FOR REPLACE ONLY WITH THE SAME TYPE FUSE6. ARE CAUTION: DIGITAL TRANSISTOR DESCRIBED IN PARTS LIST ONLY 1 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.0 0.3 48 R3816 FEED BACK SWITCHING5.6 NC 11 8. 1 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.A B C D E F G H POWER SCHEMATIC DIAGRAM 8 8 (AV PCB) R3819 D3823 30PRA60-FC 2 2 1 CP3800 A1561WV2-2P 1 W807 RU2AM-EIC C3824 C3826 DEGAUSS COIL L3800 8R200026 TO DEFLECTION D3821 2KV 0.2 8V 4 17 GND 18 D3806 C3802 S801X 0.3 6.5V C3811 1K 1/4W D3812 2 6 TO MICON/TUNER 21DQ09N R3827 2KV0.6B-EIC STAND-BY SW Q3804 DTC144EKA R3825 10 1/2W C3808 0.0 S802X MTZJ2.0 2.001 C3818 2 500V 0.2B-EIC D3828 1SS133 1SS133 D3803 1SS133 1SS133 D3826 D3802 1SS133 D3827 IS THE LIVE CONNECTION 1SS133 C3816 CAUTION: D3811 1/2W R3822 1K B 0 0 3 R3813 1K 1/4W D3822 0. A G-21 B C D E F G H G-22 .22 1W RM11C-EIC H 7 +B 200V 220 YXF R3806 7 2.0015 R POWER Q3803 2SK3563(ORION_Q) G 6.5X6X1.33 ECQUL 09414909 WIDE MLADE D3808 TH3800_2 PTDCA1BF3R0Q100 D3818 1N4937-PAN 100 1/4W RM11C-EIC AC120V_60Hz CD3800 3 RM11C-EIC P MTZJ18B-EIC 2 1 6 UNREG+12V 0. 9 3.7K 1/4W FROM/TO DEFLECTION V/C GND 22 C632 19 R619 VIDEO LINE OUT AUDIO ATT OUT(R) 25 0 FSC_OUT 18 H_CONTROL 17 B 20 1 21 SYNC_VIDEO 2.01 3.015 B S809X 8.OUT 1SS133 D605 CLAMP OFF IC601 M61277FP-DF0H 8 5 D602 6 33K1/4W SW 0 Q602 KTC3875S_Y_RTK 0.0 B C624 50V 1 KA C APC DVD_C C627 3.4 16 0.8 4 16V100 KA 40 DEF GND 6 SW Q601 KTC3875S_Y_RTK 10K 1.0 R651 4.3 C644_13.A B C D E F G H CHROMA SCHEMATIC DIAGRAM 8 8 (AV PCB) FROM REGULATOR DVD_Y DVD_C P.4 6.5 4.9 32 3.6 TUNER_VIDEO SDA Y(Y/C) IN 29 VIDEO_OUT 14 SCL 2.9 39 R643 R602 15K 1/4W 2 1SS133 2.9 S810X 2.1 C605_1 3 C639 0 0 3.579545MHz 3.1 L601 100uH0305 0305 16V 100 KA C608 P.0 7 B.8K 4.CON+8V C607 63V 1 MKT 32 R614 V_OUT 5 100 1/4W 34 33 2.2 HI VCC 4 G.3 27 W832 15 50V 1 KA TUNER_AUDIO 3.8 FROM/TO MICON/TUNER AFC 680 1/4W 42 1 B OUT 27K SYNC_VIDEO 5 R612 1.8 0.CON+5V 7 ACL MONITOR OUT HVCO F/B AUX2(R) IN VRAMP CAP HD OUT VRAMP OUT AFC FILTER C629 1 B 5.7 KANP C613 16V 100 KA C616 50V 1 KA HD AUDIO ATT FILTER R644 C615 V_RANP_FB C626 27K SW_A_OUT_L 50V 2.0 5. D E F G 1 H G-24 .2 KA W867 FSC_OUT 50V 1 KA SDA 0 11 0 W822 OSD_Y OSD G IN AUDIO ATT OUT(L) 12 OSD_R 0 OSD R IN FSC OUT 13 OSD_G FASTBLK AUX1(R) IN W827 4.0 P.2 KA TUNER_AUDIO 1K 1/4W TUNER_VIDEO W853 DVD_A_OUT_L2 50V 1 KA FRONT_VIDEO 50V 1 KA AUX2(l) IN R623 C625 3.1 100 R605 1N4005-EIC FBP IN 37 ACL D601 G OUT H_OUT 34 R641 8.1 AUX1(L) IN CVBS3 IN CVBS2 IN C618 27 50V 1 KA C621 V/C VCC 26 R63947K SW_A_OUT_R 50V 2.8K 1/4W R628 2.8 PROTECT 2.2K AFC H_OUT 2.OUT 3 R609 6 4 29 B 8.9 30 9 VD OUT 3.0 R611 C612 0.1 VD OSD_B 5.1 100CT3R505 18P CH 24 47K SPINAU MONO IN 23 R617 V_RANP_FB 2.01 B C610 3.1 50V 1 KA R607 15K C606 50V 4.01 B 2 2 TO SOUND AMP PCBD20 CME066 SW_A_OUT_L SW_A_OUT_R NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A G-23 B C CAUTION: DIGITAL TRANSISTOR NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.2 28 V_OUT C631 0.CON+8V PROTECT TO CRT 6 L603 C643 16V 100 KA C609 GND S804Y FROM/TO POWER 16V 100 KA C648 16V 100 KA C649 P.CON+5V H OUT 38 W884 R610 36 CLAMP R OUT 100 30 33 1K 1/4W 2.0 P.7K 1/4W DVD_A_OUT_R2 R616 W843 VIDEO_OUT 16V 100 KA C633 47K DVD_A_OUT_L2 75 C604 R647 FROM/TO IN/OUT 0.CON+8V 7 3 L604 5.9 0 1K 1/4W R627 H_CONTROL 0.1 35 GND 1 DEF VCC 3 2 2.4 C601_1 1 3.OUT 8.01 B R646 1SS133 D603 6.1 R650 100 31 P.3 SW Q605 KRA102SRTK 9.1 NC R618 ACL XTAL 358 CVBS1 IN 2.5 C641 X602 3.2 C645 C642 W850 DVD_A_OUT_R2 50V 1 KA DVD_Y 4 SDL C(Y/C) IN 28 4.0 5 R.CON+8V 100uH C628 41 0 CP802A (CP802B) B2013H02-6P 0.CON+5V B 10uHTSL0808 FRONT_VIDEO FRONT_A_IN_R 16V 100 KA C638 R603 FRONT_A_IN_L 2.1 2.2K 0.5 3.2 31 10 OSD B IN VRANP F/B 2.0 B P. 47 KA GND 4 4 3 3 2 2 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE PCBD20 CME066 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.2M R1519 50V 0.A B C D E F G H COMB/FILTER SCHEMATIC DIAGRAM (AV PCB) 8 8 7 7 6 6 S809Y W899 S810Y C1530_1 5 5 FROM REGLATOR 2. 1 1 A G-25 B C D E F G H G-26 . A B C D 8 E F G H 8 LOADING MOTOR/SW SCHEMATIC DIAGRAM 7 7 6 6 (LOADING MOTOR PCB) (SW PCB) 5 CD2301 2H062102 1 4 CD2302 2H052601 5 SW2 ESE22MH24 4 3 GND(SW) 2 PICK UP INNER LIMIT SWITCH 3 4 FEED MOTOR (-) 5 SPINDLE MOTOR (-) 6 SPINDLE MOTOR (+) M FEED MOTOR (+) M2602 BCZ3B03 5 SW1 SSS-13-2 SW-2(CLOSE) GND(SW) SW-1(OPEN) 2 LOADING MOTOR(+) 1 LOADING MOTOR(-) M2603 M BCZ3B52 4 M PCB640 DED002 M2601 JCV9B06 PCB610 DED003 3 3 2 2 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 1 A G-27 B C D E F G H G-28 . OUT G.V GND 2 180V HEATER 1 CP803B 4 NC NC CP802A CRT GND HEATER NC 6 9 14 SIF OUT 15 BT NC DVD RESET GND S3802 16 IF OUT 17 VIDEO OUT CP2302 FFC CLOSE 1 1 1 CLOSE GND(D) 2 2 2 GND(D) OPEN 3 3 3 OPEN LD+ 4 4 4 LD+ LD- 5 5 5 LD- 6 DVD DRIVE DK4001 CV_VLM102 OPTICAL PICK-UP 5 SPINDLE MOTOR SP1+ 1 SP1+ 4 SP1- 2 SP1- SLD+ 3 SLD+ SLD- 4 SLD- LIMIT SW 5 LIMIT SW SW(GND) 6 SW(GND) LOADING MOTOR SLED MOTOR 3 ZERO DVD RESET GND DEGAUSS COIL L3800 WHITE 2 AC120V_60Hz CD3800 BLACK 20 S3801 21 SWD_VIDEO 8 DVD_VIDEO 6 5 4 3 2 1 7 AUDIO OUT R AUDIO OUT L P.CON+A5V T+ 2 2 2 T+ P.OUT 5 6 NC 12 1 1 CVBS GND 11 11 2 2 GND C(CVBS) 10 10 3 3 C(CVBS) GND 9 9 4 4 Y(G) 8 8 5 5 GND Y(G) GND 7 7 6 6 GND AUDIO-L 6 6 7 7 AUDIO-L GND 5 5 8 8 GND AUDIO-R 4 4 9 9 AUDIO-R ZERO 3 3 10 10 2 2 11 11 1 1 12 12 8 FSC IN 9 +B 10 CLOCK 11 DATA 12 AFT OUT CP3800 13 AUDIO OUT 1 1 4 3 F CLAMP 7 12 2 2 V801 H.8V T- 1 1 1 T- P.OUT NC CP8101_3 CVBS 1 2 1 CLAMP GND 3 CP802B 22 WIDE BLADE 4 3 2 1 CP803A 9 8 CRT SOCKET J801_1 7 6 NC 4 5 VREF VCC 1 19 18 FBT FB401_1 FOCUS CP806 SCREEN 23 4 NC CLAMP_OFF 2 1 CD4002 CP8002 CD803 GND 23 4 3 NC GND GND(PDIC) 23 CP2303 SCREEN FOCUS CP805 24 VREF RDY(I/O(0)) TU001 2 24 GND MOTOR+B(+6V) 3 24 GND SSCCLK 4 FFC CP2301 GND(PDIC) RED WHITE L3803 PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES A G-29 B C D E THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY.8V GND 10 10 GND(A) SPDIF 11 11 SPDIF SSCRXD 12 12 SSCRXD SSCTXD 13 13 SSCTXD CD8101 FFC 1 2 3 4 CP401 5 180V ANODE NC 5 NC 1 GND 2 G.USE ONES ARE 1 DESCRIBED IN PARTS LIST ONLY F G H G-30 .CON+3.OUT 3 R.OUT 4 B.CON+9V I2C OFF I2C SDA AV PCB PCBD20 CME066 CD801 I2C SCL CP101 CRT PCB PCB110 CCE062 GND 5 B.CON+3.8V 9 9 P.CON+3.CON+5V 7 7 P.8V 8 8 P.CON+3.A B C D E F G H INTERCONNECTION DIAGRAM 8 8 SP352 8 OHM R CH SPEAKER 2 1 CD302 7 2 SP OUT R+ 2 2 2 2 1 NC 5 H 3 4 NC 3 H 3 2 NC 6 H 3 Vout 1 DVD PCB PCB130 DME060 GND 2 SOUND GND 1 H 7 OS2202 CP302 SP351 8 OHM 2 1 1 SP OUT L+ CP301 2 CD301 7 SOUND GND L CH SPEAKER COMMAND TRANSMITTER TM101 E 1 1 COAXIAL J4201 1 E 1 E B+ 3 E YELLOW FRONT VIDEO JACK J2202 FRONT AUDIO JACK J2203 FRONT AUDIO JACK J2204 HEADPHONE_JACK J2201 6 CP8001 5 22 22 VCC E 21 21 21 E F 20 20 20 F D 19 19 19 D A 18 18 18 A B 17 17 17 B NC 1 NC NC 2 NC C 16 16 16 C RF 15 15 15 RF DVD/CD 14 14 14 DVD/CD MON(COM) 13 13 13 MON(COM) GND(CD) 12 12 12 GND(CD) VOL(CD) 11 11 11 VOL(CD) LD(CD) 10 10 10 LD(CD) LD(DVD) 9 9 9 LD(DVD) 1 GND(D) GND(DVD) 8 8 8 GND(DVD) 2 2 GND(D) VOL(DVD) 7 7 7 VOL(DVD) SSCCLK/TX NC(SW) 6 6 6 NC(SW) MON(DVD) 5 5 5 MON(DVD) 3 3 RDY(I/O(0))/RX GND(M) 5 5 GND(M) F+ 4 4 4 F+ 6 6 P.CON+6V F- 3 3 3 F- P.OUT CLAMP_OFF 3 4 R. 0V 25 9 POWER ON 50µs 10µs 200mV 1. H-1 .2ms 1.0V 4 MEMORY 5ns 500mV 5 POWER ON 0.0V 0.2ms 1.0V 23 POWER ON 0.5V 22 27 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.WAVEFORMS MPEG/MICON/DSP AUDIO/VIDEO 10ns 500µs 100mV 500mV 1 6 5ns 500µs 20mV 500mV 2 20ns 1.0V 3 200ns 1.0V 26 10 MICON/TUNER POWER ON CHROMA POWER ON 20µs 0.2ms 1.0V 24 7 POWER ON 10µs 200mV 5ms 1. 5V 200mV 5.0V 29 POWER ON 10µs 2.0V 33 38 POWER ON DVD PLAY 20µs 2.0V 10µs 0.0V 100mV 30 35 43 POWER ON 10µs POWER ON POWER ON 1ms 100mV 20µs 5.0V 31 44 36 CRT IN/OUT POWER ON 10ms DVD PLAY 0.0V 32 37 45 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.5ms 200mV 28 POWER ON 10µs 2.0V 2.5µs 100mV 20µs 0.5V 0.5ms POWER ON 20µs 0. H-2 .WAVEFORMS STANDBY POWER ON DVD PLAY 0.5V 39 34 SOUND AMP DEFLECTION POWER ON 1ms POWER ON 5ms 10. WAVEFORMS POWER ON 20µs 50V 46 1ms 50mV 51 POWER ON 20µs 50V 47 POWER STANDBY 5µs 5.0V 48 STANDBY 5µs 5.0V 49 SOUND AMP 1ms 50mV 50 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. H-3 MECHANICAL EXPLODED VIEW 202 202 114 102B 202 202 206 202 202 102B 102B 201 113 102A 117 102 201 116 123 PCB110 (CRT PCB ASS'Y) 201 117 112 117 201 112 117 210 101C 101J 204 101I 210 101G 101H 101E 101B 101K 101D A 210 101F 101A 101 I1-1 202 MECHANICAL EXPLODED VIEW 212 106 212 121 106 208 208 208 PCB130 (DVD PCB ASS'Y) 209 209 209 208 208 208 208 208 208 209 108 208 208 208 118 208 208 208 208 110 213 119 208 121 104 203 208 120 109 213 213 206 213 115 203 PCBD20 (AV PCB ASS'Y) A 107 205 207 122 205 206 206 205 211 103 105 111 I1-2 MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) 129. 133. TM101 126 128 126 132 124 127 123 125 125 I1-3 . 131. BL001. 130. Check if the correct grease is applied for each position.DVD DECK EXPLODED VIEW 611 600 608 612 AA Cannot supply by a unit. 704 610 614 AA AA AA AA AA 613 AA 602 AA AA 609 AA 615 M2603 607 SW1 AA PCB610 (LOADING MOTOR PCB ASS'Y) 705 617 616 CD2301 701 CD2302 604 705 SW2 618 702 PCB640 (SW PCB ASS'Y) CD2001 703 606 605 Do not replace the parts. minute adjustments are needed if this condition is disassembled further more. Because. replace the DVD MECHA ASS'Y. 603 M2602 605 601 CLASS MARK GREASE AA NOTE: Applying positions AA for the grease are displayed for this section. If the repair is needed. I2-1 619 . Description 101 101A 101B 101C 101D 101E 101F 101G 101H 101I 101J 101K 72783199 72783184 72783186 72783187 72783188 72783189 72783192 72783195 72783194 72783196 72798625 72796103 7A701A597A 701WPJD184 711WPAA134 712WPJC200 713WPAA235 713WPAA236 723549A054 735WPBB479 735WPAA994 738WPAA071 742WKA0001 800WQ0A052 FRONT CABI ASS'Y CABINET FRONT PLATE FRONT FLAP DVD GLASS LED GUIDE REMOCOM BADGE BRAND BUTTON PUSH BUTTON FRAME STOPPER BUTTON SPRING DVD-FLAP FELT SHEET 102 102A 102B 72783200 72783185 72798775 7A702A192A 702WPAA948 800WQ0A046 BACK CABI ASS'Y CABINET BACK FELT SHEET 103 104 105 106 107 108 109 72799702 72799936 72798668 72798655 72799384 72799373 72798550 7250000595 761WSA0155 761WPA0249 753WUA0069 702WSAA128 702WSA0213 7230007593 SHEET PC ANGLE DECK HOLDER FBT SPRING EARTH PLATE BOTTOM SHIELD TOP SHEET JACK 110 111 112 113 114 115 116 117 118 119 72798688 72798640 72796255 72783193 72783190 72781978 72795687 72799965 72799853 72783197 774WPA0006 752WSA0333 800WR0A011 726000A133 722549A558 8965TS1017 741WUA0021 769WSAA011 752WSA0488 753WEA0033 HOLDER WIRE SHIELD JACK SHEET CRT SUPPORT (D) SHEET CRT SERVICEMAN SHEET RATING CUSHION 65TS10-10(17. HOLDER ANODE WIRE SHEET BAR CODE FILM BAG PACKAGE BOTTOM PACKAGE TOP GIFT BOX INSTRUCTION BOOK KIT POLYBAG INSTRUCTION(RED CAUTION) 130 131 132 133 72781569 72781605 72795703 72783222 J3N51617A J5S10229A 791WHAA134 J5X30401A REGISTRATION CARD INFORMATION SHEET(USA) LIGHTRON SHEET INSTRUCTION BOOK 201 202 203 204 205 206 207 208 209 72781287 72781279 72798794 72798793 72781255 72798787 72781251 72781247 72781263 8141J50C5U 8117540A6U 811754080U 8110E3080U 8109I3080U 810923080U 810963080Q 810923060U 810F13080U SCREW TAP TITE(P) GW22 5*35 CH HEXAGON SCREW TAP TITE(B0) TRUSS 4*16 CH SCREW TAP TITE(B0) TRUSS 4*8 CH SCREW TAP TITE(P) WH10 3*8 CH SCREW TAP TITE(B) WH7 3*8 CH SCREW TAP TITE(B) BIND 3*8 CH SCREW TAP TITE(B) BRAZIER 3*8 STAINLESS SCREW TAP TITE(B) BIND 3*6 CH SEMS(F) 3*8 CH 210 211 212 213 72798791 72798786 72795782 72781248 8110630A0U 810763080U 811022680U 810923070U SCREW TAP TITE(P) BRAZIER 3*10 CH SCREW TAP TITE(S) BRAZIER 3*8 CH SCREW TAP TITE(P) BIND 2.5*20*14) SPRING EARTH WASHER CRT T=1 SHIELD DECK SHEET CU 120 121 122 123 124 125 126 127 128 129 72795699 72795680 72794734 72783191 72795702 72798718 72798717 72783198 72783208 72781635 899EFBA002 8995034000 899HV3T000 723000D219 791WHAA114 792WHA0525 792WHA0524 793WCDD046 A5X304V975 JB5ND300 WIRING-CLIP CORD CLIP UL CO.MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No.6*8 CH SCREW TAP TITE(B) R BIND 3*7 CH J1-1 . PAN M1.TRAVERSE CLAMPER GEAR. TSB P/N Reference No.MAIN TRAY RACK.LOADING PLATE.FEED 1 RACK.TAP TITE(P) PAN W10 2*8 CH SCREW.3 P3 CH SEMS.DVD DECK REPLACEMENT PARTS LIST Location No.TAP TITE(P) BIND 2*8 CH 72783183 72795869 72795870 72796050 72795947 72795948 72783202 72783203 72796052 122J4O1903 122H062102 122H052601 0515S32002 1515S98003 1596S18003 A5M4016610 A5N813W640 0500101037 CORD JUMPER 127000-2928 CORD JUMPER 2H062102 CORD JUMPER 2H052601 SWITCH SSS-13-2 FEED MOTOR BCZ3B03B MOTOR.7*2.PAN M1.MAIN BELT.6*8 CH SCREW.7*3 P3 CH SCREW.RACK FEED CUSHION C 701 702 703 704 705 72795782 72795783 72795784 72795785 72796070 811022680U 814011723U 816112080U 814011730U 811022080U SCREW TAP TITE(P) BIND 2.LOADING FRAME.CLAMPER RACK.LOADING BCZ3B52B PCB ASS'Y DED003A PCB ASS'Y DED002B PUSH SWITCH ESE22MH24 CD2001 CD2301 CD2302 SW1 ! M2602 ! M2603 PCB610 PCB640 SW2 J2-1 . Description ! 600 601 602 603 604 605 606 607 608 609 72783201 72795767 72795768 72795769 72798813 72795771 72795772 72781331 72795774 72795775 A2I301H650 92P100109A 92P100094A 92P100088A 92AAA0013A 92P200013A 92P200014A 92SBB0029A 92P100095A 92P100097A DVD MECHA ASS'Y A2I301H650 HOLDER.FEED 2 SPRING.PULLEY PULLEY.MOTOR FEED RACK ASS'Y INSULATOR(F) INSULATOR(R) LOADER SUB ASS'Y GEAR.MOTOR 610 611 612 613 614 615 616 617 618 619 72795776 72795777 72795778 72795779 72795780 72798838 72798836 72798837 72798849 72795888 92P100096A 92P200012A 92P000014A 92P100093A 92P100091A 92P100092A 92P100089A 92P100090A 92P300020A 800WFAA008 GEAR. SILICON DIODE.METAL OXIDE RC R.METAL OXIDE R.METAL OXIDE R.001 UF 2KV R 220 UF 200V 2200 UF 25V DIODES ! ! ! ! ! J3-1 1SS133T-77 MTZJ5.2 OHM 3W 2.5M OHM 1/2W 2.FAST RECOVERY DIODE.METAL RC RC RC R.7K OHM 1/6W 1.SILICON DIODE.CEMENT R.ZENER DIODE.METAL OXIDE R. ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! TSB P/N Reference No.METAL OXIDE R.FAST RECOVERY DIODE.6B-EIC 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1N4002-PAN 1N4937-PAN MTZJ33B-EIC MTZJ33B-EIC 1N4002-PAN 1N4002-PAN 1SS133T-77 MTZJ33B-EIC 1SS133T-77 MTZJ6.SILICON DIODE.METAL R.SILICON DIODE.METAL OXIDE R.METAL OXIDE R.METAL OXIDE R.7 OHM 1/2W 1 OHM 1W 1 OHM 1W 5.ZENER DIODE.METAL OXIDE R.SILICON DIODE.METAL R.SILICON DIODE.001 UF 500V B 470 UF 200V 0.ZENER DIODE.FAST RECOVERY DIODE.SILICON DIODE.1B-EIC 1N4005-EIC 1SS133T-77 1SS133T-77 1SS133T-77 .27 OHM 1W 0.FUSE R.SILICON DIODE.ZENER DIODE.0047UF 250V 2200 UF 25V 10 UF 50V 1000 UF 16V 1000 UF 25V 0.METAL OXIDE R.6K OHM 1/6W 39K OHM 1/4W 100 OHM 1/2W 2.SILICON 1M OHM 1/4W 2.ZENER DIODE.SILICON DIODE.7M OHM 1/2W 330 OHM 1/2W 1 OHM 5W 1 OHM 3W 0.001 UF 2KV B 2200 UF 10V 2200 UF 10V 2200 UF 10V 0.FUSE R.8 OHM 2W 2.25KV PHE 22 UF 250V 0.ELECTRICAL REPLACEMENT PARTS LIST Location No.METAL OXIDE R.ZENER DIODE.47 UF 250V PMS 0.8B-EIC 1N4937-PAN 1N4937-PAN MTZJ5.FAST RECOVERY DIODE.FAST RECOVERY DIODE.0015 UF 2KV R 0.FAST RECOVERY DIODE.0068UF 1. Description RESISTORS R117 R310 R401 R402 R408 R418 R429 R431 R444 R445 R447 R450 R803 R805 R807 R3005 R3800 R3803 R3806 R3812 R3817 R3819 R3821 R3828 R3829 72796038 72797922 72781694 72781693 72781714 72794682 72795519 72795519 72795514 72783223 72798046 72797923 72796459 72796459 72796459 72797916 72795997 72795500 72794631 72795109 72797971 72794621 72795995 72794633 72794684 R002T4105J R3X28B2R2J R3K58A331J R3K58A221J R3X28A1R8J R002T22R7J R65581010J R65581010J R4X5T6562F R4K1T4393F R655U2101J R3X28B2R7J R3X18A153J R3X18A153J R3X18A153J R3X28B1R2J R4X5T6272F R002T2155J R0G3K2275K R002T2331J R5X2CD010J R3X28B010J R3X181R27J R63881R22J R002T4101J RC R.2 OHM 3W 330 OHM 2W 220 OHM 2W 1.001 UF 500V B 0.FUSE RC C357 C402 C407 C421 C423 C428 C431 C802 C3002 C3010 C3011 C3801 C3810 C3811 C3812 C3815 C3816 C3818 C3820 C3822 C3823 C3824 C3826 C3827 72795574 72794396 72795574 72797489 72795104 72781648 72795570 72795578 72797374 72797374 72797374 72794401 72795629 72795581 72795629 72795573 72795579 72794381 72794400 72797483 72794410 72794399 72794411 72794381 E02LF3222M E02LU8220M E02LF3222M E5EZT4471M P4J7F3474J P4G8FJ682H E0ELFD220M C0JBB0713K E02LF1222M E02LF1222M E02LF1222M P2122B334M C0JTB0513K C0PLRR7E3K C0JTB0513K E51CGC471M CD39E0MQ3M E5EZF3222M E02LU5100M E5EZT2102M E5EZF3102M C0PLRR713K E62NFC221M E5EZF3222M CE CE CE CE CMPP CMPP CE CC CE CE CE CMP CC CC CC CE CC CE CE CE CE CC CE CE D101 D102 D105 D106 D109 D110 D111 D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D413 D416 D601 D602 D603 D605 72794491 72783214 72794491 72794491 72794491 72794491 72794491 72783209 72795543 72781366 72781366 72783209 72783209 72794491 72781366 72794491 72781369 72795543 72795543 72781368 72795626 72794491 72794491 72794491 D1VT001330 D9WU05R62B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D2MXN40020 D2MXN49370 D9WU03302B D9WU03302B D2MXN40020 D2MXN40020 D1VT001330 D9WU03302B D1VT001330 D9WU06R82B D2MXN49370 D2MXN49370 D9WU05R12B D2WXN40050 D1VT001330 D1VT001330 D1VT001330 DIODE.22 OHM 1W 100 OHM 1/4W CAPACITORS ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! 2200 UF 25V 22 UF 100V 2200 UF 25V 470 UF 35V 0.SILICON DIODE.7 OHM 3W 15K OHM 2W 15K OHM 2W 15K OHM 2W 1.FUSE R.SILICON DIODE.33 UF 275V ECQUL 0. SILICON DIODE.SILICON DIODE.SCHOTTKY DIODE.SILICON DIODE.SILICON DIODE.ELECTRICAL REPLACEMENT PARTS LIST Location No. ! ! ! ! ! ! ! ! ! ! ! ! TSB P/N Reference No.SILICON DIODE.FAST RECOVERY DIODE.FAST RECOVERY DIODE.SILICON DIODE.SILICON TRANSISTOR.SCHOTTKY DIODE.SILICON IC101 IC103 IC199 IC352 IC353 IC401 IC601 IC2301 IC3001 IC3002 IC3800 IC4001 IC4003 IC4007 IC4009 IC8102 72783219 72796084 72783207 72783215 72783215 72795534 72783217 72783216 72783218 72795906 72794512 72783220 72795912 72783224 72783221 72795922 I55F06087A I9UF032310 A5W1014D25 I01DP75130 I01DP75130 I03TD804N0 I06FC12770 I03FV65650 I07F90WTP0 I1KA78R050 000220002W ICQK068621 I07F9E00W0 S5W1013F01 IF9J0161A7 I17F017530 IC IC INIT DATA IC IC IC IC IC IC IC PHOTO COUPLER IC IC MEMORY DATA IC IC Q101 Q104 Q401 Q402 Q403 Q405 Q406 Q601 Q602 72794571 72794566 72794569 72795474 72795475 72794561 72782813 72794571 72794571 TCAA3875SY TAAA1504SY TA3T016240 TC3T029090 TA3T1371A0 TCAT03227Y TC1G058850 TCAA3875SY TCAA3875SY TRANSISTOR.RECTIFIER DIODE.ZENER DIODE.SILICON TRANSISTOR.ZENER DIODE.SILICON TRANSISTOR.SILICON TRANSISTOR.SCHOTTKY DIODE.ZENER DIODE.ZENER DIODE.ZENER DIODE.FAST RECOVERY DIODE.SILICON DIODE.ZENER DIODE.SILICON 1SS133T-77 1SS133T-77 1SS133T-77 LTL-1CHEE-002A 1SS355 TE-17 1SS355 TE-17 1N4002-PAN MTZJ10B-EIC MTZJ5.ZENER DIODE.SILICON DIODE.SILICON DIODE.SILICON DIODE.SILICON DIODE.E)-AE KTC3227_Y-AT 2SC5885 KTC3875S_Y_RTK KTC3875S_Y_RTK .SILICON DIODE.SILICON TRANSISTOR.SILICON DIODE.SILICON DIODE.SILICON DIODE.SILICON DIODE.SILICON DIODE.SILICON DIODE.6B-EIC 1N4002-PAN 21DQ09N-TA2B1 11E1-EIC MTZJ5.SILICON DIODE.SILICON LED DIODE.2B-EIC 1N4937-PAN MTZJ3.9B-EIC 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 ICS ! ! ! ! ! ! ! ! OEC6087A PST3231NR AT24C04N-10SU-2.SILICON DIODE.ZENER DIODE.6B-EIC 1SS133T-77 1SS133T-77 MTZJ18B-EIC 1SS133T-77 1N4937-PAN RM11C-EIC RM11C-EIC MTZJ18B-EIC 1SS133T-77 1SS133T-77 MTZJ3.SILICON TRANSISTOR.SILICON TRANSISTOR.SILICON TRANSISTOR.7 AN7513 AN7513 LA78040N-E M61277FP-DF0H LA6565VR-TLM-E BA00BC0WT-V5 KIA278R05PI PS2561AL1-1-V(W) ZR36862PQCG-B BA33E00WHFP-TR SST39VF1601-70-4C-EKE M12L16161A-7TG PCM1753DBQR TRANSISTORS ! ! ! ! J3-2 KTC3875S_Y_RTK KTA1504S_Y_RTK 2SA1624-AA 2SC2909(S.6B T-77 RM11C-EIC RM11C-EIC 21DQ09N-TA2B1 1N4937-PAN 21DQ09N-TA2B1 21DQ09N-TA2B1 RU2AM-EIC 1SS133T-77 30PRA60-FC 21DQ09N-TA2B1 MTZJ12B-EIC 1SS133T-77 1SS133T-77 MTZJ2.SCHOTTKY DIODE.SCHOTTKY DIODE. Description DIODES D804 D805 D806 D2201 D2303 D2304 D3001 D3002 D3003 D3004 D3005 D3006 D3801 D3802 D3803 D3804 D3806 D3807 D3808 D3809 D3810 D3811 D3812 D3814 D3815 D3816 D3817 D3818 D3819 D3820 D3821 D3822 D3823 D3824 D3825 D3826 D3827 D3828 D3829 D3831 D4002 D4003 D4004 D4005 D4006 D4007 D8111 D8112 72794491 72794491 72794491 72796482 72795897 72795897 72783209 72783210 72783214 72783209 72794480 72794488 72783214 72794491 72794491 72783211 72794491 72795543 72794473 72794473 72783211 72794491 72794491 72797336 72794473 72794473 72794480 72795543 72794480 72794480 72795545 72794491 72794474 72794480 72781364 72794491 72794491 72783212 72795543 72783213 72795897 72795897 72795897 72795897 72795897 72795897 72795897 72795897 D1VT001330 D1VT001330 D1VT001330 0021E2Q140 DD7R0S3550 DD7R0S3550 D2MXN40020 D9WU01002B D9WU05R62B D2MXN40020 D28T21DQN9 D2WT011E10 D9WU05R62B D1VT001330 D1VT001330 D9WU01802B D1VT001330 D2MXN49370 D2WTRM11C0 D2WTRM11C0 D9WU01802B D1VT001330 D1VT001330 D97U03R61B D2WTRM11C0 D2WTRM11C0 D28T21DQN9 D2MXN49370 D28T21DQN9 D28T21DQN9 D2WXRU2AM0 D1VT001330 D28F0PRA60 D28T21DQN9 D9WU01202B D1VT001330 D1VT001330 D9WU02R22B D2MXN49370 D9WU03R92B DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 DIODE.ZENER DIODE.SILICON DIODE.SILICON DIODE.SILICON DIODE.T)-AA 2SA1371(D.FAST RECOVERY DIODE.FAST RECOVERY DIODE.SILICON DIODE.SILICON DIODE. E)-RAC 2SC4217(D. Description TRANSISTORS Q605 ! Q804 ! Q805 ! Q806 Q2201 Q2301 Q2302 Q2303 Q2304 Q2305 ! Q3001 ! Q3002 Q3003 ! Q3005 Q3007 ! Q3008 Q3800 ! Q3802 ! Q3803 Q3804 Q4201 Q4202 Q4203 Q4204 Q4205 Q4206 72795963 72795971 72795971 72795971 72794567 72795964 72795965 72794571 72794571 72794571 72796092 72796092 72795962 72794570 72795962 72795476 72794577 72795476 72795539 72794559 72794571 72795966 72794571 72794571 72794558 72794567 TPAAB05001 TC3F042170 TC3F042170 TC3F042170 TNAAC05002 T67J1036K0 T67J048TL0 TCAA3875SY TCAA3875SY TCAA3875SY TAAT01281Y TAAT01281Y TNAAB05003 TCAT03209Y TNAAB05003 TCAT032034 TCATC31980 TCAT032034 T25F035630 TNYJD05001 TCAA3875SY TPYJA05001 TCAA3875SY TCAA3875SY TNAAD05001 TNAAC05002 COMPOUND TRANSISTOR TRANSISTOR.TUBE HEADPHONE JACK RCA JACK RCA JACK RCA JACK RCA JACK SW2213 SW2214 SW2215 SW2216 SW2217 SW2218 SW2219 SW2220 SW2221 SW2223 72794688 72794688 72794688 72794688 72794688 72794688 72794688 72794688 72794688 72794688 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 SWITCH.SILICON COMPOUND TRANSISTOR TRANSISTOR.ELECTRICAL REPLACEMENT PARTS LIST Location No.2 UH W5T29X7.SILICON TRANSISTOR.TACT SWITCH. TSB P/N Reference No.SILICON TRANSISTOR.E)-RAC KRC103SRTK 2SA1036KT146 2SA2048TL KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTA1281_Y KTA1281_Y KRC102SRTK KTC3209_Y-AT KRC102SRTK KTC3203_Y-AT KTC3198-AT(Y.SILICON TRANSISTOR.SILICON TRANSISTOR.TACT SWITCH.TACT SWITCH.SILICON TRANSISTOR.TACT SWITCH.BEADS CORE.BEADS CORE.SWITCHING ! J801 ! J2201 J2202 J2203 J2204 J4201 72795490 72794516 72795924 72795925 72795926 72796734 066F130020 060J131016 060J421036 060J421037 060J421030 060J401102 SOCKET.LINE FILTER COIL CORE.TACT SWITCH.SILICON FET COMPOUND TRANSISTOR TRANSISTOR.BEADS CORE.TACT SWITCH.BEADS KRA102SRTK 2SC4217(D.SILICON TRANSISTOR.SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR L001 L101 L401 L601 L603 L604 ! L3800 L3801 L4001 L4002 L4202 L8102 L8103 T401 ! T3800 72796407 72796582 72794527 72794540 72794540 72796087 72796616 72798947 72795936 72796088 72794540 72795943 72795943 72796466 72796693 02167D101K 021LA6560K 021679472K 02167F101J 02167F101J 02167E100K 028R200026 029X000126 02167F2R2J 02AHB9A972 02167F101J 02167F1R0K 02167F1R0K 045011001L 0481300034 COIL COIL COIL COIL COIL COIL COIL.SILICON TRANSISTOR.SEMI FIXED NVG6TLTAB222 NVG6TLTAB471 P.SILICON COMPOUND TRANSISTOR TRANSISTOR.TACT SWITCH.DEGAUSS COIL.SILICON TRANSISTOR.BOARD ASSEMBLIES CCE062A DME060A CME066A MISCELLANEOUS J3-3 MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT W4BRH3.E)-RAC 2SC4217(D.SILICON TRANSISTOR.CATHODE RAY.SILICON COMPOUND TRANSISTOR TRANSISTOR.FERRITE COIL COIL COIL TRANS.GR) KTC3203_Y-AT 2SK3563(ORION_Q) DTC144EKAT146 KTC3875S_Y_RTK DTA143EKAT146 KTC3875S_Y_RTK KTC3875S_Y_RTK KRC104SRTK KRC103SRTK COILS &TRANSFORMERS 100 UH 56 UH 4.BEADS CORE.SEMI FIXED VOLUME.TACT VR402 VR3800 72795471 72796061 V1K63H3BTE V1K63Q2BTE PCB110 PCB130 PCBD20 72783204 72783205 72783206 A5W1014110L A5W1014130L A5W1014D20L PCB ASS'Y PCB ASS'Y PCB ASS'Y B2301 B2302 B2303 B2304 B2305 B3800 B4001 72795787 72795787 72795787 72795787 72795787 72794355 72795787 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 024HT03563 0246C51024 CORE.5X19 100 UH 1 UH 1 UH STP-03Q24 81300034 JACKS ISHS53S MSJ-2000_AG MTJ-032-05A-30-FE MTJ-032-05A-32-FE MTJ-032-05A-31-FE MSP-251V-05NI-FE-LF SWITCHES EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R VARIABLE RESISTORS VOLUME.HORIZONTAL DRIVE TRANSFORMER.0X2 MMZ1608R102CT .C.BEADS CORE.SILICON TRANSISTOR.SILICON COMPOUND TRANSISTOR TRANSISTOR.TACT SWITCH.5X6X1.SILICON TRANSISTOR.BEADS CORE.7 MH 100 UH 100 UH 10 UH 8R200026 SS26V-R120220 2.TACT SWITCH. .BEADS CORE.......BALUN BATTERY...... METAL POLYPROPYLENE CAPACITOR J3-4 MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT W5RH3.....BEADS CORE......... POLYPROPYLENE CAPACITOR CPL..BEADS CORE...MANGAN CORD....... METAL POLYESTER CAPACITOR CMPL........ 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 024HT03553 0246C51024 023C00022A 141U004016 141U004016 06CU12414A 06CU12414A 06CU823001 WDL6042038 WBL6034038 069S290629 069W120459 069W120459 069S450089 069S320010 1209414909 06CU2D2202 122F0C1602 069KYOT159 069EV53030 069EV63030 069S420110 069S2D0629 069J7C0599 067U006049 067U006049 067U004029 067U004029 069J7C0589 124116281A 124120301A 081PC6R305 043219024Y 06710T0009 06710T0009 077A031002 070Y033004 070Y033004 076D0MG010 0163300020 DF20C3R0Q0 098Q210447 1002T01606 100DT3R531 100GT02720 Description MISCELLANEOUS CORE.........BEADS CORE....AC BUSH CORD... POLYESTER CAPACITOR CPP..FLYBACK HOLDER...FUSE HOLDER.... PLASTIC CAPACITOR CMP.BEADS CORE..BEADS CORE...CONNECTOR CORD..BEADS CORE....5X5X1..........BEADS CORE. ! ! ! ! ! ! ! ! ! ! B4002 B4003 B4005 B4006 B4007 B4008 B4009 B4010 B4011 B4012 B4013 B4014 B4016 B4018 B4201 B8103 BL001 BT001 BT002 CD301 CD302 CD801 CD802 CD803 CP101 CP301 CP302 CP401 CP805 CD3800 CD4002 CD8101 CP2301 CP2302 CP2303 CP3800 CP8001 CP8002 CP802A CP802B CP803A CP803B CP8101 ELD201 ELD202 F3800 FB401 FH3800 FH3801 OS2202 SP351 SP352 TM101 TU001 TH3800 V801 X101 X602 X4001 TSB P/N 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72795787 72794357 72795787 72782870 72783174 72783174 72796874 72796874 72796912 72798419 72798397 72796804 72799049 72799049 72796822 72796816 72795554 72783178 72797046 72783177 72799012 72799013 72796821 72796810 72796776 72796752 72796752 72796750 72796750 72799040 72797069 72797070 72794493 72783176 72794496 72794496 72783180 72799171 72799171 72783179 72783175 72797351 72783181 72796990 72794704 72783182 Reference No....CONNECTOR FLAT CABLE FLAT CABLE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD.. CARBON RESISTOR CAPACITORS CC... CERAMIC CAPACITOR CE..JUMPER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER CONNECTOR PCB SIDE EYE LET EYE LET FUSE TRANSFORMER.........MANGAN BATTERY..CONNECTOR CORD.........CONNECTOR CORD.......BEADS COIL..FUSE REMOTE RECEIVER SPEAKER SPEAKER TRANSMITTER RF UNIT DEGAUSS ELEMENT CRT W/DY CERAMIC OSCILLATOR CRYSTAL CRYSTAL RESISTOR RC......0 MMZ1608R102CT HPN-01 MNAAA(R03) MNAAA(R03) CU12414A CU12414A CU823001 AWM2468 AWG26 6C BLACK 420MM AWM2468 AWG26 4C BLACK 340MM A2001WV2-9P 213213102W1 213213102W1 A1561WV2-A5P A2361WV2-2P 9414909 CU2D2202 2F0C1602 LD07T2-24ND-03 00_6232_005_006_800+ 00_6232_006_006_800+ A1561WV2-2P A2001WV2-13P IMSA-9604S-12C B2013H02-6P B2013H02-6P B2013H02-4P B2013H02-4P IMSA-9604S-12F XRY16X28BD XRY20X30BD 51MS063L BSC23-N0168 EYF-52BCY EYF-52BCY ROM-N3138SR S08F52 S08F52 ORT204N7405860-Z 115-V-KA35ARE PTDCA1BF3R0Q100 A51AEZ90X23 CSTLS16M0X53-A0 HC-49/U B27000C005 .........ELECTRICAL REPLACEMENT PARTS LIST Location No.........BEADS CORE.... ALUMI ELECTROLYTIC CAPACITOR CP.BEADS CORE...BEADS CORE....BEADS CORE...BEADS CORE...BEADS CORE.. METAL PLASTIC CAPACITOR CMPP..BEADS CORE..... TOKYO 105-8001. MINATO-KU. JAPAN .TOSHIBA CORPORATION 1-1. SHIBAURA 1-CHOME.