SAES-A-020

Engineering StandardSAES-A-020 6 April 2008 Equipment Specific P&ID Templates (ESPT) Equipment Specific P&ID Templates (ESPT) Standards Committee Members Mehra, Yuv R., Chairman Fernandez, Gabriel T., Vice Chairman Al-Abeediah, Saeed M. Al-Hashim, Ghalib A. Al-Hamam, Ibrahim H. Al-Hawaj, Ameen A. Al-Lajami, Abdullah A. Al-Zaid, Radhi H. Al-Amer, Hamid A. Al-Agnam, Salman M. Rafie, Nader Y. Benham, Donald G. Authement, Richard Al-Juaib, Mohammed K. Zoker, Samuel B. Al-Ghamdi, Fahad A. Al-Otaibi, Dhawi A. Al-Assiry, Nasser Y. Al-Shaikh, Tariq H. Al-Dossery, Isa K. Fayez, Amin A. Fayez, Luai A. Al-Mohsin, Mohsin S. Saudi Aramco DeskTop Standards Table of Contents 1 2 3 4 5 Scope............................................................. 2 Conflicts and Deviations................................. 2 References..................................................... 3 Design Philosophy........................................ 11 ESPT Services & Applications..................... 13 Original Issue: New Next Planned Update: 6 April 2013 Primary contact: Mehra, Yuv R. (+966-3) 873-4311 Copyright©Saudi Aramco 2008. All rights reserved. Page 1 of 20 Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 1 SAES-A-020 Equipment Specific P&ID Templates (ESPT) Scope This standard prescribes Equipment Specific P&ID Templates (ESPTs) to be used to define the process, piping and instrumentation configuration requirements for specifically identified major equipment and simple processes. Unless a deviation from these requirements has been approved or is allowed as described herein below, the defined requirements are to be followed precisely with neither deletions nor additions. This standard is applicable to all identified equipment in hydrocarbon processing facilities including utility services incorporated in hydrocarbon facilities. This standard does not cover the process and mechanical design, sizing, specification, selection, and installation of major equipment that is the subject of any ESPT. This standard is mandatory for all engineering work, both preliminary engineering (Project Proposal or FEED) and detailed design, performed under reimbursable or time unit rate contracts (under which the contractor’s warranty is only for rework); for work carried out in-house; and for design changes proposed by Saudi Aramco as the scope of Change Orders under lump sum contracts. For detailed design performed under lump sum contracts (under which the contractor is fully responsible for the performance of the facility), this standard shall be used as a guideline and the contractor shall have the right to deviate from the ESPTs as it deems necessary, provided the contractor satisfies the requirement under 2.3. The Design Basis Scoping Paper (DBSP) for the development of project’s Piping & Instrument Drawing(s) (P&ID) shall reference this entire standard during the Front-End Engineering Design (FEED) or Project Proposal (PP)/Detail Design. 2 Conflicts and Deviations 2.1 Any conflicts between this standard and other applicable Saudi Aramco Engineering Standards (SAESs), Materials System Specifications (SAMSSs), or industry standards, codes, and forms shall be resolved in writing by the Company or Buyer Representative through the Manager, Process & Control Systems Department of Saudi Aramco, Dhahran. 2.2 For preliminary and detailed designs performed under reimbursable or time unit rate contracts or for work carried out in-house, request for deviations from this standard shall be submitted in writing to the Company Representative, who shall follow internal company procedure SAEP-302 and forward such requests to the Manager, Process & Control Systems Department of Saudi Aramco, Dhahran. 2.3 For detailed design work performed under lump sum contracts, deviations from this standard shall be reported in writing to the Company Representative, who Page 2 of 20 and repair of equipment and facilities covered by this standard shall comply with the latest edition of the references listed below. Dhahran. 3 References The selection of material and equipment. SASDs and SABPs in Section 3 here below.1 Saudi Aramco References Saudi Aramco Engineering Procedures SAEP-1027 Pressure Relief Valve Conventional and Balanced Types SAEP-1028 Chemical Cleaning and Flushing of Lube/Seal Oil and Fluid Power Systems SAEP-110 Saudi Aramco Standard Drawings SAEP-119 Preparation of Saudi Aramco Materials System Specifications SAEP-121 Operating Instructions for New Facilities SAEP-125 Preparation of Saudi Aramco Engineering Standards SAEP-1350 Design Basis Scoping Paper (DBSP) Preparation and Revision Procedure SAEP-14 Project Proposal SAEP-16 Project Execution Guide for Process Automation Systems SAEP-1662 Cleaning of Heat Exchangers and Unfired Plant Equipment SAEP-302 Instructions for Obtaining a Waiver of a Mandatory Saudi Aramco Engineering Requirement SAEP-303 Engineering Reviews of Project Proposal and Detail Design Documentation Page 3 of 20 . maintenance. SAMSSs. By inclusion of following SAEPs. all such references are deemed to be an integral part of this standard and shall be applied when and where applicable within the scope of a specific ESPT.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) shall forward such information to the Manager. Process & Control Systems Department of Saudi Aramco. unless otherwise noted. 3. SAESs. construction. specification. and the design. sizing. Inspection. API SPEC 6A 31-SAMSS-001 Centrifugal Compressors 31-SAMSS-002 Packaged Reciprocating Plant and Instrument Air Compressors 31-SAMSS-003 Reciprocating Compressors for Process Air or Gas Service 31-SAMSS-004 Centrifugal Pumps Page 4 of 20 . In-Plant Piping and Pressure Vessels for Resistance to HydrogenInduced Cracking 04-SAMSS-001 Gate Valves 04-SAMSS-002 Globe Valves 04-SAMSS-003 Additional Requirements for Low Temperature Valves 04-SAMSS-005 Check Valves. Swing Type 04-SAMSS-035 General Requirements for Valves 04-SAMSS-050 Gate Valves.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) SAEP-305 Saudi Aramco Library Drawings SAEP-317 Testing and Inspection (T&I) of Shell and Tube Heat Exchangers SAEP-318 Pressure Relief Valve Program Authorization for Installation. Through Conduit Type. Quality Assurance and Regulation SAEP-333 Cathodic Protection Monitoring SAEP-341 Equipment Life Cycle Cost Procedure SAEP-349 Advanced Process Control (APC) Systems SAEP-364 Process Simulation Model Development and Support SAEP-50 Project Execution Requirements for Third Party Royalty/Custody Metering Systems Saudi Aramco Materials System Specifications 01-SAMSS-016 Qualifications of Pipeline. Deletion and Changes SAEP-319 & 319A Pressure Relief Valves – Routine Test. API SPEC 6D 04-SAMSS-051 Ball Valves. API SPEC 6D 04-SAMSS-052 Ball Valves. Internally Geared Centrifugal Air Compressors 31-SAMSS-009 Positive Displacement Pumps – Controlled Volume 31-SAMSS-012 Shaft Sealing Systems for Centrifugal and Rotary Pumps 32-SAMSS-004 Manufacture of Pressure Vessels 32-SAMSS-005 Manufacture of Atmospheric Tanks 32-SAMSS-006 Manufacture of Low Pressure Tanks 32-SAMSS-007 Manufacture of Shell and Tube Heat Exchangers 32-SAMSS-009 General Purpose Steam Turbines 32-SAMSS-010 Special Purpose Steam Turbines 32-SAMSS-011 Manufacture of Air-Cooled Heat Exchangers 32-SAMSS-013 Lubrication. Shaft Sealing and Control Oil Systems 32-SAMSS-019 Manufacture of Plate and Frame Heat Exchangers 32-SAMSS-020 Manufacture of Trays and Packing 32-SAMSS-027 Manufacture of Electric Heat Exchangers 32-SAMSS-028 Manufacture of Double Pipe Heat Exchangers 32-SAMSS-029 Manufacture of Fired Heaters 32-SAMSS-030 Manufacture of Small Tanks 32-SAMSS-031 Manufacture of Clad Vessels and Heat Exchangers 32-SAMSS-100 Combustion Gas Turbines 34-SAMSS-112 Orifice Meter for Gas Custody Measurement 34-SAMSS-114 Ultrasonic Flow Meter for Gas Custody Measurement 34-SAMSS-117 Turbine Flow Meters in Liquid Service 34-SAMSS-118 Positive Displacement Meters 34-SAMSS-119 Bi-Directional Meter Prover 34-SAMSS-120 Uni-Directional Meter Prover Page 5 of 20 .Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) 31-SAMSS-005 Centrifugal Fluorocarbon Refrigeration Units for Industrial/Process Services 31-SAMSS-006 Packaged. Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) 34-SAMSS-318 Automatic Tank Gauging Equipment 34-SAMSS-319 Radar Tank Gauging Equipment 34-SAMSS-511 Chromatographs 34-SAMSS-512 Oxygen Analyzers 34-SAMSS-514 Combustible Gas and Hydrogen Sulfide Monitors 34-SAMSS-515 Moisture Analyzers 34-SAMSS-517 Density Meters 34-SAMSS-525 Automatic Sampling Systems for Crude Oil and Refined Products 34-SAMSS-611 Safety Relief Valves Conventional and Balanced Types 34-SAMSS-612 Safety Relief Valves – Pilot Operated Types 34-SAMSS-621 ESD Systems – Hard wired – Solid-State (Nonprogrammable) 34-SAMSS-622 ESD Systems – Electromagnetic Relay 34-SAMSS-634 Local ZV Control Systems 34-SAMSS-711 Control Valves – General Services 34-SAMSS-716 Pneumatic Actuators On-Off Service 34-SAMSS-717 Hydraulic Valve Actuator Systems 34-SAMSS-718 Electric Motor Operated Valve Actuators Saudi Aramco Engineering Standards SAES-A-202 Saudi Aramco Engineering Drawing Preparation SAES-A-207 Catalyst and Desiccant Selection and Replacement SAES-B-055 Plant Layout SAES-B-057 Safety Requirements: Refrigerated and Pressure Storage Tanks and Vessels SAES-B-058 Emergency Shutdown. Isolation and Depressuring SAES-C-001 Process Design of Trays and Packing SAES-D-001 Design Criteria for Pressure Vessels SAES-D-100 Design Criteria of Atmospheric and Low-Pressure Tanks Page 6 of 20 . Shaft Sealing and Control Oil Systems SAES-G-116 Cleanliness Standard for Lube/Seal Oil and Fluid Power Systems SAES-J-001 Instrumentation Index SAES-J-003 Instrumentation – Basic Design Criteria SAES-J-004 Instrumentation Symbols and Identification SAES-J-005 Instrumentation Drawings and Forms SAES-J-100 Process Flow Metering SAES-J-200 Pressure SAES-J-300 Level SAES-J-400 Temperature SAES-J-502 Analyzer Shelters SAES-J-600 Pressure Relief Devices SAES-J-601 Emergency Shutdown and Isolation Systems SAES-J-603 Process Heaters Safety Systems SAES-J-605 Surge Relief Protection Systems SAES-J-700 Control Valves SAES-J-904 FOUNDATION™ Fieldbus (FF) Systems SAES-K-402 Centrifugal Compressors Page 7 of 20 .Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) SAES-D-109 Design of Small Tanks SAES-E-004 Design Criteria of Shell and Tube Heat Exchangers SAES-E-006 Design Criteria of Double Pipe Heat Exchangers SAES-E-007 Design Criteria of Air-Cooled Heat Exchangers SAES-E-014 Design Criteria of Plate and Frame Heat Exchangers SAES-E-015 Design Criteria of Electric Heat Exchangers SAES-F-001 Design Criteria of Fired Heaters SAES-G-005 Centrifugal Pumps SAES-G-006 Positive Displacement Pumps – Controlled Volume SAES-G-115 Lubrication. Typical schematic AA-036762-001 Cathodic Protection. Crude and Product Tank Bottom Internal Galvanic Anode Installation AA-036859-001 Lube Oil Circulation System Piping and Instrument Diagram (P&ID) AA-036911-001 Insulation Details for Hot Piping Page 8 of 20 . Piping and Process Equipment SAES-L-140 Thermal Expansion Relief in Piping SAES-N-100 Refractory Systems SAES-O-100 General Requirements Safety and Security SAES-O-127 Tank Spacing – Dikes and Drainage SAES-P-113 Motors and Generators SAES-S-020 Industrial Drainage and Sewers SAES-X-500 Cathodic Protection of Vessel and Tank Internals SAES-X-600 Cathodic Protection of Plant Facilities SAES-Y-101 Custody Metering of Hydrocarbon Gases SAES-Y-103 Royalty/Custody Metering of Hydrocarbon Liquids SAES-Z-000 Process Control Standards Index SAES-Z-001 Process Control Systems Saudi Aramco Standard Drawings AA-036388-001 Cathodic Protection Internal Galvanic Anodes Installation Detail for Vessels AA-036513-001 Custody Transfer Metering and Proving Station (Liquid).Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) SAES-K-403 Reciprocating Compressors SAES-K-501 Steam Turbines SAES-K-502 Combustion Gas Turbines SAES-L-105 Piping Material Specifications SAES-L-108 Selection of Valves SAES-L-130 Material for Low Temperature Service SAES-L-132 Material Selection for Piping Systems SAES-L-133 Corrosion Protection Requirements for Pipelines. Blinds and Spacers for Class 125 Cast Iron Flanges AD-036633-001 Spectacle Plates.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) AA-036912-001 Insulation Details for Hot Vessels AA-036913-001 Insulation Details for Cold Piping AA-036913-002 Insulation Details for Cold Vessels AB-036003-001 Manways and Vents for Tanks AB-036019-001 Thermowell Assembly and Detail AB-036054-001 Oily Water Sewer Manholes Miscellaneous Details AB-036094-001/002 Standard Orifice Plates AB-036305-001 Standard Equipment Symbols AB-036379-001 Royalty/Custody Metering for Hydrocarbon Gases AB-036492-001 Local Instrument Symbols (Pneumatic and Electrical) for Instrument Loop Diagrams AB-036492-002 Local Instrument Symbols (Miscellaneous) for Instrument Loop Diagrams AB-036764-001 Temporary Suction Screen for Gas Compressors AC-036004-001 Orientation for Orifice Flanges AC-036045-001 Detail Vent. Drain and Sample Connections AC-036688-001 Conical Pump Suction Screen for Class 150 and 300 Flanges Pipe Sizes 16” AC-036950-001 Instrument Symbols AC-036963-001 Assembly of Davits for Side Mounting on Pressure Vessels AD-036080-001 Conical Pump Suction Screen for Raised Face Flange Pipe Sizes 2”. 8”. Blinds and Spacers for Class 150 Raised Face Flanges Page 9 of 20 . 10” and 12” AD-036631-001 Spectacle Plates. 3” and 4” AD-036393-001 Letter Designation for Line Numbers AD-036467-001 Blinds for API-3000 PSI Ring Joint Flanges AD-036491-001 In-Line Instrument Symbols for Instrument Loop Diagrams AD-036495-001 Conical Pump Suction Screen for Raised Faced Flanges Pipe Sizes 6”. Blinds and Spacers for Class 250 R. Ring Joint Flanges AD-036735-001 Spectacle Plates.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) AD-036636-001 Spectacle Plates.I. Blinds and Spacers for Class 900 Oct. Ring Joint Flanges AE-036046-001 Detail of ½” Standard Sample Tube AE-036084-001 Pump Suction Screen Flat AE-036092-001 Vertical Ladders Details for Tanks AE-036411-001/002/003 Drawing and Equipment Index Key AE-036549-001 Minimum Instrumentations for Separator Vessels AE-036550-001 Branch Connections to Flare Headers Saudi Aramco Best Practices SABP-A-002 Load Management for Energy Efficiency: Pumps and Compressors SABP-A-008 Load Management for Energy Efficiency: Heat Transfer Equipment SABP-A-009 Pinch Technology for Energy Efficiency Optimization SABP-A-011 Energy Conservation Requirements in Saudi Aramco Engineering Standards and Materials Systems Specifications SABP-A-012 New Projects Energy Efficiency Optimization Review Methodology SABP-A-013 Corrosion Control in Amine Units SABP-A-015 Chemical Injection Systems SABP-A-016 Crude Unit Corrosion Control SABP-F-001 Process Heaters Optimizations SABP-G-013 Rotating Equipment Piping Strain Diagnosis Page 10 of 20 . Blinds and Spacers for Class 600 Oct. and Class 300 Raised Face Flanges AD-036734-001 Spectacle Plates. Blinds and Spacers for Class 1500 Oct.C. Ring Joint Flanges AD-036736-001 Spectacle Plates. Blinds and Spacers for Class 600 Raised Face Flanges AD-036731-001 Spectacle Plates.F. For example.3 Terminology The terminology and nomenclature used in ISA and ANSI standards applies to this standard. etc. outlet flow measurement is provided to enable assessment of equipment’s performance. flow measurement has been limited to single phase streams. when more than one piece of equipment is required in a process configuration. Where appropriate. No sizing for equipment. separation. 3. seawater. appropriate ESPT may be used more than once as required.2 SAES-A-020 Equipment Specific P&ID Templates (ESPT) SABP-K-002 Introduction to Industrial Refrigeration Systems Targeting SABP-Q-004 Heat Exchanger and Horizontal Vessel Foundation Design SABP-X-001 Cathodic Protection Design Package Preparation Industry Codes and Standards All industry codes and standards as referenced in SA referenced standards are applicable. Upon the availability of project’s Process Flow Diagram(s) (PFD). care must be taken by the engineering teams so as not to duplicate instrumentation that can be Page 11 of 20 . the utility side stream(s) like cooling water. each ESPT is limited to a single piece of major equipment. For some of the common hydrocarbon processing applications to Saudi Aramco. In such cases. Multi-phase streams are not measured.) are included on ESPTs. For all other equipment. and treating of the hydrocarbon process streams. 4 Design Philosophy Each ESPT in this standard is designed to be used as a building block for developing a project’s P&IDs. inlet stream flow measurement is provided only for gas compressors. Except for the pumps. In these ESPTs. this standard provides ESPTs for typical systems that serve as an example of how ESPTs can be configured together for a specific project or application. such as for heat exchangers. steam or steam condensate are integrated into the ESPTs. and appropriate operational control. or internal dimensions (related to liquid levels or minimum spacing.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 3. the P&IDs are generally developed during the FEED or the PP phases of the project. This standard provides ESPTs only for major equipment for processing. These data are specific to a project and its process application and configuration. instrument range. piping. such as two (2) fifty percent (50%) or four (4) twenty-five percent (25%) capacity. If a project’s Hazard and Risk Analysis (e. etc.g. such deviations should be documented in the HAZOP study report. if three (3) fifty percent (50%) capacity pumps are required. or having multiple bypasses around the multitude of equipment. indicated piping and instrumentation for minimum flow in the ESPT must be deleted. Page 12 of 20 . Unless otherwise provided under the notes for a specific ESPT. b) Minimum distance requirements. The mass transferred shall be determined by means of a metering system employing Coriolis meters. Since it is not practical to capture all aspects of engineering in ESPTs. Should a specific project choose to incorporate Foundation Fieldbus technology. these items can be incorporated in project’s P&IDs without securing P&CSD prior approval. etc.) and density meters.. then such project’s P&IDs shall conform to the requirements of SAES-J-904 to appropriately indicate legends of all FF instruments. operational. mass measurement of such liquid streams shall be implemented. for example. ZVs. the indicated requirement for instrument(s) and the designated control philosophy (as incorporated in each ESPT. which are subject to custody transfer measurements as defined by SAES-Y-103. additional considerations for developing final P&IDs are as follows: a) Indication of piping insulation and heat tracing as required. loss prevention. A meter prover and density meter (if required) shall also be provided for meter calibration. For multiple services. and maintenance for minimizing life cycle costs for such major process equipment) must be used without changes. because each pump ESPT has two pumps. Each pump ESPT is based on the provision of one (1) hundred-percent (100%) capacity pump operating and one (1) hundred-percent (100%) capacity pump spare. ultrasonic. Care must be taken during design engineering to assure that each pump is protected for minimum flow requirement and that there is no duplication of flow measurement or level control of the operating pumps. or volumetric meters (turbine. Each ESPT is provided with specific notes that allow certain flexibility to facilitate smooth design engineering by the engineering contractor without requiring unnecessary waivers to this standard. instruments. reflect the best practices for engineering. such as ethane-plus natural gas liquids (C2+ NGL). All instrumentation shown in ESPTs of this standard is conventional type. For any hydrocarbon liquid streams that are rich in ethane. provided one pump is deleted from the final P&ID. and using twice will result in four pumps. However.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 SAES-A-020 Equipment Specific P&ID Templates (ESPT) combined into a single measurement.. If for a selected pump minimum flow protection is not required or necessary. HAZOP) study dictates addition or deletion of any valves. the pump ESPT may be used twice. ESPT Services & Applications This standard provides ESPTs for following selected major process equipment categories: 5.1 Series 100 Compressors Series 200 Pumps Series 300 Turbines Series 400 Vessels Series 500 Tanks Series 600 Columns Series 700 Exchangers Series 800 Fired Heaters Series 900 Process System Configurations Series 100 – Compressors This standard provides ESPTs for the following clickable compression services: Template No. e) Provision for corrosion coupons. f) Minimize nozzles on vessels.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 5 SAES-A-020 Equipment Specific P&ID Templates (ESPT) c) Indication of low and high alarms for process measurements within DCS.g. Service ESPT-101 M88-DA-950164-001 Single-Stage Centrifugal Compressor ESPT-102 M88-DA-950164-002 Multi-Stage Reciprocating Compressor Page 13 of 20 . Drawing No.. sample points. e. etc. chemical injection. h) Incorporation of piping related to hydrotesting. d) Low point drains and high point vents. g) Provision of start-up and permanent suction screens on rotating equipment. provide relief valves on outlet piping instead on vessel. purging and inventorying for process start-up and T&I. Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 Template No.2 SAES-A-020 Equipment Specific P&ID Templates (ESPT) Drawing No.000 HP Page 14 of 20 . Drawing No.000 HP ESPT-204 M88-DA-950165-004 Lube Oil System for Pumps ESPT-205 M88-DA-950165-005 Oily Water Lift Station ESPT-206 M88-DA-950165-006 Reciprocating Pump Below 300 HP ESPT-007 M88-DA-950165-007 Vertical Canned Pump – 300 to 1. Service ESPT-103 M88-DA-950164-003 Screw Compressor ESPT-104 M88-DA-950164-004 One-Stage Centrifugal Refrigerant Compressor ESPT-105 M88-DA-950164-005 Two-Stage Centrifugal Refrigerant Compressor ESPT-106 M88-DA-950164-006 Three-Stage Centrifugal Refrigerant Compressor ESPT-107 M88-DA-950164-007 Lube Oil System for Compressors Series 200 – Pumps This standard provides ESPTs for the following clickable pump services: Template No. Service ESPT-201 M88-DA-950165-001 Centrifugal Pump Below 300 HP ESPT-202 M88-DA-950165-002 Desanding Stripper Pump ESPT-203 M88-DA-950165-003 Horizontal Centrifugal Pump Above 1. 5. O. Service ESPT-401 M88-DA-950167-001 Dual Gas Outlet Drum ESPT-402 M88-DA-950167-002 Ethane Refrigerant Accumulator ESPT-403 M88-DA-950167-003 Gas Filter Separator ESPT-404 M88-DA-950167-004 Flare K.4 Drawing No.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 5.500 HP ESPT-303 M88-DA-950166-003 Single Train CGT Fuel Gas System ESPT-304 M88-DA-950166-004 Back Pressure Steam Turbine >2. 5.500 HP ESPT-305 M88-DA-950166-005 Turbo-Expander/Compressor Series 400 – Vessels This standard provides ESPTs for the following clickable vessel services: Template No. Drawing No.* Drum ESPT-405 M88-DA-950167-005 Gas Compressor Suction Drum ESPT-406 M88-DA-950167-006 GOSP** Desalter ESPT-407 M88-DA-950167-007 GOSP Three-Phase Drum ESPT-408 M88-DA-950167-008 GOSP Two-Phase Drum ESPT-409 M88-DA-950167-009 Horizontal Coalescer Drum ESPT-410 M88-DA-950167-010 Horizontal Two-Phase Drum ESPT-411 M88-DA-950167-011 Mercury Removal Bed Page 15 of 20 .3 SAES-A-020 Equipment Specific P&ID Templates (ESPT) Series 300 – Turbines This standard provides ESPTs for the following clickable turbine services: Template No. Service ESPT-301 M88-DA-950166-001 Gas Expander ESPT-302 M88-DA-950166-002 General Purpose Steam Turbine <2. Service * ** *** Drawing No.O. SAES-A-020 ESPT-412 M88-DA-950167-012 Molecular Sieve Dehydrator ESPT-413 M88-DA-950167-013 Propane Refrigerant Accumulator ESPT-414 M88-DA-950167-014 Reflux Drum ESPT-415 M88-DA-950167-015 Refrigerant Compressor Suction Drum ESPT-416 M88-DA-950167-016 Refrigerant Economizer ESPT-417 M88-DA-950167-017 Slug Catcher ESPT-418 M88-DA-950167-018 Split Flow Inlet Horizontal Drum ESPT-419 M88-DA-950167-019 Three-Phase Horizontal Drum ESPT-420 M88-DA-950167-020 Two-Phase Vertical Drum ESPT-421 M88-DA-950167-021 Vertical Coalescer Drum ESPT-422 M88-DA-950167-022 Wet Crude Dehydrator ESPT-423 M88-DA-950167-023 WOSEP*** K.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 Equipment Specific P&ID Templates (ESPT) Template No. = Knock Out GOSP = Gas Oil Separation Plant WOSEP = Water Oil Separation Page 16 of 20 . Drawing No. Service ESPT-501 M88-DA-950168-001 Emergency Water Disposal Tank ESPT-502 M88-DA-950168-002 Fixed Roof Product Tank ESPT-503 M88-DA-950168-003 Floating Roof Product Tank ESPT-504 M88-DA-950168-004 Low Pressure Degassing Tank ESPT-505 M88-DA-950168-005 Product Storage Sphere ESPT-506 M88-DA-950168-006 Product Storage Spheroid ESPT-507 M88-DA-950168-007 Water Storage Tank Series 600 – Columns This standard provides ESPTs for the following clickable column services: Template No.6 Drawing No.5 SAES-A-020 Equipment Specific P&ID Templates (ESPT) Series 500 – Tanks This standard provides ESPTs for the following clickable tank services: Template No. Service ESPT-601 M88-DA-950169-001 Packed Absorber Column ESPT-602 M88-DA-950169-002 Packed Distillation Column ESPT-603 M88-DA-950169-003 Packed Rectifier Column ESPT-604 M88-DA-950169-004 Packed Stripper Column ESPT-605 M88-DA-950169-005 Trayed Absorber Column ESPT-606 M88-DA-950169-006 Trayed Distillation Column ESPT-607 M88-DA-950169-007 Trayed Rectifier Column ESPT-608 M88-DA-950169-008 Trayed Stripper Column ESPT-609 M88-DA-950169-009 Steam Stripper Column Page 17 of 20 .Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 5. 5. Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 5. * Drawing No. Service ESPT-701 M88-DA-950170-001 Air Cooled Heat Exchanger ESPT-702 M88-DA-950170-002 Air Cooled Refrigerant Condenser ESPT-703 M88-DA-950170-003 BAHE* Cross-Exchanger ESPT-704 M88-DA-950170-004 BAHE* Refrigerant Chiller ESPT-705 M88-DA-950170-005 Deethanizer Overhead Condenser ESPT-706 M88-DA-950170-006 Electric Heat Exchanger ESPT-707 M88-DA-950170-007 Evaporated Humidified Cooling System ESPT-708 M88-DA-950170-008 Horizontal Thermosyphon Reboiler ESPT-709 M88-DA-950170-009 Kettle Reboiler ESPT-710 M88-DA-950170-010 Kettle Refrigerant Chiller ESPT-711 M88-DA-950170-011 Kettle Steam Generator ESPT-712 M88-DA-950170-012 Plate & Frame Heat Exchanger ESPT-713 M88-DA-950170-013 Shell & Tube Heat Exchanger ESPT-714 M88-DA-950170-014 Steam Heated Thermosyphon Reboiler ESPT-715 M88-DA-950170-015 Vertical Thermosyphon Reboiler ESPT-716 M88-DA-950170-016 Water Cooled Heat Exchanger ESPT-717 M88-DA-950170-017 Water Cooled Refrigerant Condenser ESPT-718 M88-DA-950170-018 Once-Through Thermosyphon Reboiler (Steam) BAHE = Brazed Aluminum Heat Exchanger Page 18 of 20 .7 SAES-A-020 Equipment Specific P&ID Templates (ESPT) Series 700 – Exchangers This standard provides ESPTs for the following clickable column services: Template No. 5.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 5.9 Drawing No. Drawing No. this standard provides ESPTs for the following clickable process system services: Template No. Service ESPT-801 M88-DA-950171-001 Crude Oil Furnace ESPT-802 M88-DA-950171-002 Vacuum Furnace Series 900 – Process System Configurations To illustrate the use of ESPTs for developing P&IDs for any process application and any configuration as determined appropriate by the process design and as reflected in the project’s PFD.8 SAES-A-020 Equipment Specific P&ID Templates (ESPT) Series 800 – Fired Heaters This standard provides ESPTs for the following clickable fired heater services: Template No. Service ESPT-901 M88-DA-950180-001 Distillation Column System ESPT-902 M88-DA-950180-002 Single-Stage Refrigeration Cycle ESPT-903 M88-DA-950180-003 Two-Stage Refrigeration Cycle ESPT-904 M88-DA-950180-004 Three-Stage Refrigeration Cycle ESPT-905 M88-DA-950180-005 Crude Stabilizer System ESPT-906 M88-DA-950180-006 Condensate Stabilizer System ESPT-907 M88-DA-950180-007 Absorber Column System ESPT-908 M88-DA-950180-008 Stripper Column System ESPT-909 M88-DA-950180-009 TEG* Dehydration System ESPT-910 M88-DA-950180-010 Amine Sweetening System ESPT-911 M88-DA-950180-011 Molecular Sieve Dehydration System ESPT-912 M88-DA-950180-012 Molecular Sieve Regeneration System Page 19 of 20 . Service * ** *** *** 6 April 2008 Drawing No.Document Responsibility: ESPT Standards Committee Issue Date: 6 April 2008 Next Planned Update: 6 April 2013 Equipment Specific P&ID Templates (ESPT) Template No. SAES-A-020 Single-Stage Gas compression System ESPT-913 M88-DA-950180-013 ESPT-914 M88-DA-950180-014 Two-Stage Gas Compression System ESPT-915 M88-DA-950180-015 Three-Stage Gas Compression System ESPT-916 M88-DA-950180-016 Product Shipping and Custody Measurement ESPT-917 M88-DA-950180-017 Product NGL Fractionation System ESPT-918 M88-DA-950180-018 GOSP** Crude Dehydration & Desalting System ESPT-919 M88-DA-950180-019 GOSP HPPT/LPPT*** System ESPT-920 M88-DA-950180-020 Cryogenic Turbo-Expander Process ESPT-921 M88-DA-950180-021 Enhanced Absorption System ESPT-922 M88-DA-950180-022 Evaporative Cooling Tower System ESPT-923 M88-DA-950180-023 Once-Through Thermosyphon Reboiler System TEG = Tri-Ethylene Glycol GOSP = Gas Oil Separation Plant HPPT = High Pressure Production Trap LPPT = Low Pressure Production Trap Revision Summary New Saudi Aramco Engineering Standard. Page 20 of 20 .