Rockwell T 221 T 223 Transfer Case Parts Manual

INTRODUCTION • This parts book is designed so that you can look up part numbers in two different ways. 1. If you know the part number of the transfer case, for example, if the model number is T-223-H36, you simply match the item number in the picture with the item number in the parts list. The parts list shows which part number is used on each model. 2. If you don't know the model number, the description column in the parts list has descriptions of the different part numbers that are used on different models. • This book only lists current models. Included with the list of models covered is a list of superseded models. For service parts for models not listed, contact Meritor Specifications Department, Florence, Kentucky (888) 725-9355. • All Meritor gears and shafts are marked with the check letter and final digits of the part number, for example, F-5024 or X-2442. • When you service gears, we recommend that you replace all mating gears for the best quality repair. • Proper tools and maintenance procedures must be used. For T-221 series and T-223 series transfer cases, follow the service instructions on Meritor Field Maintenance Manual 3A. Also see Meritor Field Maintenance Manual No. 1 for proper lubricant, lubricant capacities and change intervals. Manuals may be obtained by calling the to Meritor’s Customer Service Center at 800-535-5560. • Service kits include parts to service all the different models covered by this book, so the kit may include extra parts that you won't need. In addition to kits, individual parts are available. • For service parts, contact ArvinMeritor Commercial Vehicle Aftermarket, 888-725-9355. In Canada, 800-668-3508/option 7. TABLE OF CONTENTS Page 1. T-223/ T-221 Series Supersessions............................................................................... 2 2. T-223/ T-221 Series Options........................................................................................... 3 3. T-223/ T-221 Series Service Kit Reference.................................................................... 4 4. T-223 Series Service Kits P.T.O. Miscellaneous Parts.................................................................................... P.T.O. Bearings/Shims........................................................................................... Main Case Seals.................................................................................................... Main Case Bearings/Shims/Spacers...................................................................... Capscrews/Washers/Nuts...................................................................................... Main Case Miscellaneous Parts............................................................................. DLM 10" x 1-1/2" Non-Asbestos Brake Kit............................................................. DCM 10" x 3" Brake Kit.......................................................................................... Shaft Output and Input Assemblies....................................................................... Shaft P.T.O. ........................................................................................................... 6 6 6 7 8 9 9 9 10 11 T-221 Series Service Kits Main Case Seals.................................................................................................... Main Case Miscellaneous Parts............................................................................. Main Case Fasteners............................................................................................. DLM 7-1/4" x 1-1/2" Non-Asbestos Brake Kit......................................................... 11 11 12 12 T-223 Transfer Case Power Take Off...................................................................................................... Main Case.............................................................................................................. DLM Brake............................................................................................................. DCM Brake............................................................................................................. 13 15 32 34 5. 6. 7. T-221 Transfer Case Main Case.............................................................................................................. 35 DLM Brake............................................................................................................. 40 7. Numerical Parts Listing.................................................................................................. 41 1 T-223 SERIES SUPERSESSIONS MODEL T-223-A84 T-223-A88 T-223-A89 T-223-A90 T-223-A92 T-223-A94 T-223-A102 T-223-A103 T-223-A104 T-223-A105 T-223-C22 T-223-C35 T-223-C41 T-223-C42 T-223-C43 T-223-C44 T-223-E22 T-223-E23 T-223-H29 T-223-H31 T-223-H33 T-223-H39 T-223-H40 T-223-H41 T-223-H44 T-223-H45 T-223-H52 T-223-H53 T-223-H54 T-223-H55 T-223-H56 T-223-H57 T-223-M4 RELEASE DATE Oct-82 May-83 Oct-84 Oct-84 Oct-86 Jan-91 Mar-95 Mar-96 May-96 Jan-97 Jun-83 Aug-94 Mar-96 Oct-96 Apr-96 Jan-97 Jan-89 Apr-83 May-82 May-82 Oct-82 Sep-84 Sep-84 Jan-86 Feb-88 Nov-90 Jan-96 Feb-96 Mar-96 Mar-96 Jun-96 Aug-96 Oct-82 MODEL T-221-A1 T-221-M6 T-221-M7 T-221-N4 T-221-N7 RELEASE DATE Mar-59 Mar-61 Mar-61 Apr-67 Apr-68 REPLACES RELEASE MODEL DATE T-223-A73 May-75 T-223-A36 May-63 T-223-A57 Jan-68 REPLACES MODEL RELEASE DATE T-223-A2 Dec-55 REPLACES MODEL RELEASE DATE T-223-A83 T-223-A91 Oct-82 May-86 T-223-A35 May-63 T-223-A Nov-59 T-223-A101 T-223-A100 T-223-C9 T-223-C30 T-223-C39 T-223-C37 T-223-C36 T-223-C38 T-223-E18 T-223-E13 Oct-94 Sep-94 Nov-68 Sep-93 Apr-95 Jan-95 Nov-94 Mar-95 Sep-71 May-63 T-223-A99 T-223-A98 Aug-94 May-93 T-223-A-95 T-223-A97 Jan-91 Mar-91 T-223-C26 T-223-C32 T-223-C29 T-223-C29 T-223-C31 T-223-E8 T-223-E7 Jul-86 Jun-93 Sep-92 Sep-92 Sep-92 Nov-61 Feb-61 T-223-C20 T-223-C28 T-223-C23 T-223-C23 T-223-C27 Feb-83 Jan-89 Nov-83 Nov-83 Apr-87 T-223-E3 Feb-60 T-223-H5 T-223-H16 Oct-63 Apr-70 T-223-H1 May-60 T-223-H36 T-223-C40 Jan-83 May-95 T-223-H25 T-223-C34 Oct-80 May-94 T-223-C33 Feb-94 T-223-H50 T-223-H49 T-223-H48 T-223-H51 T-223-M2 Mar-95 Sep-94 Sep-93 Oct-95 Dec-63 T-223-H46 T-223-H47 T-223-H43 Sep-92 Nov-92 Oct-87 T-223-H32 T-223-H42 Oct-82 Jul-86 T-223-M Mar-61 T-221 SERIES SUPERSESSIONS REPLACES MODEL T-221-A T-221-M3 T-221-M4 T-221-N1 T-221-N5 RELEASE DATE Oct-55 Dec-59 Dec-59 Apr-66 Apr-67 REPLACES MODEL T-221-M T-221-M1 T-221-M7 T-221-N2 2 RELEASE DATE Feb-59 Apr-59 Mar-61 Apr-66 REPLACES MODEL T-221-M T-221-M4 T-221-M8 RELEASE DATE Feb-59 Dec-59 Mar-61 . DLM DECLUTCH BRAKE X 7-1/4" x 1-1/2" X X X DCM BRAKE 3 INTERLOCK X X X X SPEEDO GEARS X FLANGE/YOKE FRONT REAR INPUT OUTPUT OUTPUT X X X X X X X X X . X X DECLUTCH X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X DLM BRAKE DCM BRAKE INTERLOCK 10" x 1-1/2" 10" x 1-1/2" 10" x 1-1/2" 10" x 1-1/2" 10" x 1-1/2" SPEEDO GEARS X X X X X 10" x 1-1/2" 10" x 1-1/2" 10" x 1-1/2" FLANGE/YOKE FRONT REAR INPUT OUTPUT OUTPUT X X X X X X X X X X X X X X X X 10" x 1-1/2" X X 10" x 1-1/2" X 10" x 3" X X X X 10" x 1-1/2" 10" x 1-1/2" 10" x 3" 10" x 3" X X X X X X X X X X X X X X X X X X X X X X X X X T-221 SERIES OPTIONS MODEL T-221-A1 T-221-M6 T-221-M7 T-221-N4 P.TO.TO.T-223 SERIES OPTIONS MODEL T-223-A84 T-223-A88 T-223-A89 T-223-A90 T-223-A92 T-223-A94 T-223-A102 T-223-A103 T-223-A104 T-223-A105 T-223-C22 T-223-C35 T-223-C41 T-223-C42 T-223-C43 T-223-C44 T-223-E22 T-223-E23 T-223-H29 T-223-H31 T-223-H33 T-223-H39 T-223-H40 T-223-H41 T-223-H44 T-223-H45 T-223-H52 T-223-H53 T-223-H54 T-223-H55 T-223-H56 T-223-H57 T-223-M4 P. T-223 SERIES SERVICE KITS REFERENCE MODEL T-223-A84 T-223-A88 T-223-A89 T-223-A90 T-223-A92 T-223-A94 T-223-A102 T-223-A103 T-223-A104 T-223-A105 T-223-C22 T-223-C35 T-223-C41 T-223-C42 T-223-C43 T-223-C44 T-223-E22 T-223-E23 T-223-H29 T-223-H31 T-223-H33 T-223-H39 T-223-H40 T-223-H41 T-223-H44 T-223-H45 T-223-H52 T-223-H53 T-223-H54 T-223-H55 T-223-H56 T-223-H57 T-223-M4 T223-1 T223-2 X X X X T223-3 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X KIT NUMBER T223-4 T223-5 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X T223-6 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X T223-7 X X X X X X X X X X X X X X T-221 SERIES SERVICE KITS REFERENCE MODEL T-221-A1 T-221-M6 T-221-M7 T-221-N4 T-221-N7 T-221-1 X X X X X KIT NUMBER T-221-3 T-221-4 X X X X X X X X X X 4 T-221-5 X T223-8 X X . T-223 SERIES SERVICE KITS REFERENCE MODEL T-223-A84 T-223-A88 T-223-A89 T-223-A90 T-223-A92 T-223-A94 T-223-A102 T-223-A103 T-223-A104 T-223-A105 T-223-C22 T-223-C35 T-223-C41 T-223-C42 T-223-C43 T-223-C44 T-223-E22 T-223-E23 T-223-H29 T-223-H31 T-223-H33 T-223-H39 T-223-H40 T-223-H41 T-223-H44 T-223-H45 T-223-H52 T-223-H53 T-223-H54 T-223-H55 T-223-H56 T-223-H57 T-223-M4 MPS-3831 MPS-4118 MPS-4120 MPS-4121 MPS-4122 MPS-4123 MPS-4124 MPS-4126 MPS-4217 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 5 . MISCELLANEOUS PARTS PART NUMBER K-2412 A-1805-N-352 K-238 A-1805-B-158 2297-Z-6656 1874-A-105 2858-T-20 1898-H-34 1229-E-421 2858-W-101 1898-Q-251 2858-X-102 1228-K-37 16-X-40 QTY 1 1 2 1 1 1 1 1 2 1 1 2 1 1 KIT T-223-2 PART NAME Shims-P. tube ITEM NUMBER ON EXPLODED VIEW 2 5 18. 122. 23 27 10. 162.O.T. shaft cap (. 35. shaft brg. BEARINGS/SHIMS PART NUMBER 2803-V-568 2803-W-569 2803-X-570 332 335 2297-Z-6656 ITEM NUMBER ON EXPLODED VIEW QTY 3 3 5 2 2 1 11 11 11 12.O. shaft cap (. 106.T. 228 KIT T-223-3 PART NAME Oil Seal-input shaft front brg. outer and inner Silicone Gasket-3 oz. cap and output shaft front Oil Seal-input shaft front brg.T.003") Shims-P.T.O. 39 48 54 55. shaft Cotter-shift lever and shift lever stud Oil Seal-P. cap and rear output shaft Oil Seal-front output shaft rear Oil Seal-shift shaft Silicone Gasket-3 oz.T. cap Oil Seal-input shaft front brg. shift shaft Silicone Gasket-3 oz. 148 A-1205-T-1242 A-1805-A-573 1 2 86 86.O.O.O. 61 60 14B P. shaft cap (.O. 150.T. 35. outer and inner Cone-P.T.005") Shims-P. tube MAIN CASE SEALS 6 . 96 A-1805-P-536 A-1205-N-1132 2297-Z-6656 1 2 1 160 200.T. 16 13. 49 8 32 33 31.O.O.T.O.010") Cup-P. shaft brg. shaft P. 15 10.O.O. shaft oil seal Spring-shift lock ball Ball-shift shaft lock Lockwasher-shift lockscrew and drive clutch retainer Spring-oil pump plunger Ball-pump inlet check valve Spring-check valve Ball-pump outlet check valve Key-tapered P. tube Sleeve-P.T. shaft nut Oil Seal-P. 49 PART NUMBER A-1805-R-408 QTY 2 ITEM NUMBER ON EXPLODED VIEW 86. 201 70.T.T-223 SERIES SERVICE KITS KIT T-223-1 PART NAME Cotter-P.T. cap (. cap (. 228 132 8 ITEM NUMBER ON EXPLODED VIEW . Cone-idler shaft front brg. cap and idler shaft front brg. cap (. Spacer-rear output shaft Spacer-rear output shaft Cone-rear output shaft forward brg. 131 125. cap (.T-223 SERIES SERVICE KITS KIT T-223-4 PART NAME Cup-input shaft rear Cone-input shaft rear Cone-input shaft front Cone-input shaft front Cup-input shaft front Cup-input shaft front Washer-input shaft front Washer-input shaft front Washer-input shaft front Shim-input shaft front brg. Cup-rear output shaft forward brg. Cone-rear output shaft rear brg. Shim-rear output forward brg. 122.005") Shim-rear output forward brg. cap (.010") Spacer-input shaft Cup-rear output shaft rear brg. 135 2803-B-1848 8 115. Cup-idler shaft front brg. tube Washer-idler shaft brg.003") Shim-rear output forward brg.010") Shim-input shaft front brg. 135 2803-A-1847 4 115. Bearing-output shaft front Bearing-front output shaft rear Spacer-front output shaft Silicone Gasket-3 oz. cap (.005") Shim-input shaft front brg.003") Shim-input shaft front brg. cap (.010") Cup-idler shaft front and rear brg. 106. cap (. Spacer-idler shaft front brg. 162. 135 31521 31597 1844-L-480 HM-89449 HM-89411 1828-V-74 1828-S-149 1244-Q-1629 2297-Z-6656 1829-H-788 2 2 1 1 1 1 1 1 1 1 124. cap and idler shaft front brg.005") Shim-input shaft front brg. cap (. cap (. Cone-idler shaft front and rear brg. cap and idler shaft front brg.003") Shim-input shaft front brg. 130 127 130 131 151 159 161 70.003") Shim-input shaft front brg. cap (. cap (.010") Shim-input shaft front brg. MAIN CASE BEARINGS/SHIMS/SPACERS PART NUMBER 332 339 357 376 353 372 1229-F-3048 1229-F-2814 1229-E-3047 2803-L-1832 2803-M-1833 2803-N-1834 2803-B-1874 2803-C-1875 2803-D-1876 2803-G-1931 2803-H-1932 2803-J-1934 1844-C-809 25520 25584 1844-S-565 1844-J-166 25878 25821 2803-Z-1846 QTY 1 1 1 1 1 1 1 1 1 2 4 2 2 6 1 2 6 4 1 1 1 1 1 1 1 4 71A 71B 79A 79A 79B 79B 79C 79C 79C 80 80 80 80 80 80 80 80 80 78 109 110 108 108 113 114 115. 150.005") Shim-input shaft front brg. O. 58 1229-E-1669 8 7. 140 S-256P-2 8 6.T.T. Capscrew-oil catcher Washer-oil catcher and brake pull rod Capscrew-front output shaft rear cap and case top cover Stud-rear output shaft Nut-rear output shaft Lockscrew-shift fork Washer-bellcrank pin Washer-brake oil detector Washer-bake mounting capscrew and brake drum capscrew Capscrew-brake mounting Capscrew-brake drum Capscrew-brake drum Washer-brake Nut-lock CAPSCREWS/WASHERS/NUTS PART NUMBER 1227-L-714 QTY 4 ITEM NUMBER ON EXPLODED VIEW 1. 138. idler shaft front brg.O. 143.O. 84. front brg. 164. 59 4-X-1521 1829-J-244 WA-38 NL-28-1 26-X-56 3-X-161 1229-E-421 S-267-2 1229-E-421 S-268-2 1229-K-1597 1 1 1 1 1 1 1 1 1 14 67 17 21 22 24 26 30 31 38 39 44.O. 94. and front output shaft rear cap Washer-input shaft rear brg. 104. 210 S-269-1 46 46. P. 88. 221. 213 4-X-840 N-16-1 26-X-54 WA-310 1829-Z-754 1229-E-1513 6 6 2 1 1 8 166 167 204. 146. carrier to T-case. 118. cage.T. rear output shaft and front output shaft Capscrew-P. 137. 209 225 174 176. shaft. 165 1829-S-721 1829-P-380 1229-F-3048 1229-F-2814 1229-E-3047 1829-V-100 1229-E-1331 1829-H-788 10-X-830 WA-36 S-2610-2 1 1 1 1 1 2 2 1 1 2 7 72 75 79C 79C 79C 87. cap. rear output and rear output forward cap. 117. case and top cover Washer-cage to T-cage. 141 87.T-223 SERIES SERVICE KITS KIT T-223-5 PART NAME Nut-P.O.O. cap. input shaft front and rear brg. cap. carrier to T-case. 120.T. shaft cap and oil pump to carrier Stud-shift lever Washer-shift shaft Washer-shift lever stud Nut-shift lever stud Lockscrew-shift fork Screw-shift shaft lock ball Lockwasher-shift lockscrew Capscrew-drive clutch retainer Lockwasher-drive clutch retainer Capscrew-cage to T-case.T. input shaft front and rear brg. carrier Washer-P. 119. shaft cap and oil pump to P. 185 S-278A-2 S-276D-2 S-166D-2 WA-39 1779-Z-260 4 4 4 1 1 177 187 245 232 231 10 . input shaft. 95 132 142 153.T. 147. rear output and rear output forward cap. 45. front brg. idler shaft front and rear cap. cage. 83. 211 43. Washer-direct drive gear Washer-input shaft front Washer-input shaft front Washer-input shaft front Washer-input and output shaft Washer-input shaft and rear output shaft nut Washer-idler shaft brg. 222 165. 103. front output shaft rear cap and case and top cover Capscrew-P. 68. 102. rear output shaft nut. and output shaft nut Bushing-speed driven gear Snap Ring-idler shaft Pin-oil drain Snap Ring-front output shaft Snap Ring-brake hub Plug-oil drain Lockscrew-shift fork Dowels. 219 217.T-case and cover Pin-brake bellcrank Washer-bellcrank pin Cotter-bellcrank pin Washer-brake pull rod Cotter-brake pull rod Ball-shift shaft lock Spring-shift shaft lock Spring-shift shaft lock Spring-shift shaft lock PART NUMBER 1829-P-380 K-2412 1199-M-1105 1854-E-187 K-236 1254-M-91 1854-W-257 1850-T-150 26-X-54 1846-X-284 1846-B-262 WA-310 K-248 WA-36 K-236 1898-E-57 2858-A-1 2858-C-237 2858-B-236 QTY 1 3 1 1 1 1 1 1 2 2 1 1 1 1 1 2 2 2 2 ITEM NUMBER ON EXPLODED VIEW 75 89. c PART NUMBER 2297-L-6720 2258-Q-719 A6-3722-L-194 QTY 1 4 2 ITEM NUMBER ON EXPLODED VIEW 179 180 181 DCM 10" x 3" BRAKE KIT KIT T-223-8 PART PART NAME NUMBER Spring-brake shoe return 2758-A-53 Nut-lock 1779-Z-260 Capscrew-brake mounting S-289A-2 c Brake lining and rivets available separately in kit 2000-S-1397 d Brake lining and rivets available separately in kit 2000-J-1362 12 QTY 1 1 4 ITEM NUMBER ON EXPLODED VIEW 238 231 235 d . 218 217. 139 89 123 54 156 170 192 204. 219 217. 219 DLM 10" x 1-1/2" NON-ASBESTOS BRAKE KIT KIT T-223-7 PART NAME Roller-brake Spring-brake shoe return Brake Shoe and Lining Assy.T-223 SERIES SERVICE KITS KIT T-223-6 MAIN CASE MISCELLANEOUS PARTS PART NAME Washer-direct drive gear Cotter-input shaft nut. 222 226. 209 214 215 225 225 221. 227 216. T-223 SERIES SERVICE KITS MPS 3831 SHAFT-OUTPUT ASSEMBLY PART NAME Shaft-output assy. Shaft-gear assy. Nut-output shaft PART NUMBER 3297-S-1370 1227-C-939 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 112 140 MPS 4120 SHAFT-INPUT PART NAME Shaft-input Nut-input shaft PART NUMBER 3297-S-1372 1227-C-939 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 77 88 MPS 4121 SHAFT-INPUT PART NAME Shaft-input Nut-input shaft PART NUMBER 3297-S-1373 1227-C-939 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 77 88 MPS 4122 SHAFT-INPUT PART NAME Shaft-input Nut-input shaft PART NUMBER 3297-Y-1374 1227-C-939 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 77 88 MPS 4123 SHAFT-INPUT PART NAME Shaft-input Nut-input shaft PART NUMBER 3297-Y-1375 1227-C-939 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 77 88 MPS 4124 SHAFT-INPUT PART NAME Shaft-input Nut-input shaft PART NUMBER 3297-Y-1376 1227-C-939 14 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 77 88 . Oil Seal-output shaft front Oil Seal-front output shaft rear Expansion Plug-front output shaft Expansion Plug-brake hub Elbow-high oil level Snap Ring-brake hub Nut-output shaft PART NUMBER A-3297-Q-1369 A-3892-E-5465 A-1805-R-408 A-1805-P-536 PW-225 PW-252 1898-X-258 1854-W-257 1227-C-939 QTY 1 1 1 1 1 1 1 1 1 MPS 4118 ITEM NUMBER ON EXPLODED VIEW 155 158 148 160 168 171 197B 170 140 SHAFT-REAR DRIVE OUTPUT PART NAME Shaft-output assy. 218 217. 227 216. 219 217.T-223 SERIES SERVICE KITS MPS 4126 SHAFT-P. Gear-output assy.O. 139 98 100 102 154. 102. 226. Nut-output shaft PART NUMBER A-3297-Q-1369 A-3892-E-5465 1227-C-939 QTY 1 1 1 ITEM NUMBER ON EXPLODED VIEW 155 158 140 T-221 SERIES SERVICE KITS KIT T-221-1 PART NAME Oil Seal-input shaft front brg. PART NAME Shaft-output assy. 219 . 201 MAIN CASE MISCELLANEOUS PARTS PART NUMBER K-2412 1199-M-1105 1898-U-671 K-2410 K-236 1898-E-57 2858-A-1 2858-Q-277 16 QTY 3 1 1 1 2 2 2 1 ITEM NUMBER ON EXPLODED VIEW 89. 148. rear output shaft. cap.T. output shaft front and front output shaft rear Oil Seal-front output shaft rear Oil Seal-shift shaft MAIN CASE SEALS PART NUMBER A-1805-E-447 A-1205-Z-1768 A-1205-N-1132 KIT T-221-3 PART NAME Cotter-input shaft nut. 96. 160 160 200. Nut-output shaft PART NUMBER 3297-Y-1378 1227-C-939 QTY 1 1 ITEM NUMBER ON EXPLODED VIEW 14 140 MPS 4217 SHAFT-OUTPUT PART NAME Shaft-output assy. rear output shaft nut and output shaft nut Bushing-speed driven gear Sleeve-speed driven gear Cotter-rear output shaft nut Pin-oil catcher and brake pull rod Ball-shift shaft lock Spring-shift shaft lock Spring-shift shaft lock QTY 4 1 2 ITEM NUMBER ON EXPLODED VIEW 86. 104. front brg. 103. 94. cap Nut-input shaft. e A13-3722-T-202 e Lining and rivets available separately in kit 2000-Q-173 PART NAME 18 QTY 2 2 2 ITEM NUMBER ON EXPLODED VIEW 179 180 181 . 83. cap. 120. 210 1829-X-726 1829-Y-727 S-2612-2 1 1 6 72 75 84. 222 67. 146 1827-H-242 S-2614-2 10-X-665 S-269-1 3 1 1 6 88. 137. 119. cap and front brg. 209 213 215 225 221. case and top cover Washer-input shaft front and rear brg. rear output cap. 104. 210 WA-16 36 68. 83. 137. front output shaft rear cap. rear output forward cap. cap. cage. idler shaft rear and front brg. 164. cap Nut-output shaft Washer-output shaft Snap Ring-front output shaft Lockscrew-shift fork Capscrew-case top cover Pin-brake bellcrank Washer-bellcrank pin Washer-brake pull rod Capscrew-input shaft front and rear brg. 140 103 103 130. 117. rear output cap. cage. rear output forward cap. Washer-direct drive gear Capscrew-input shaft front brg. 211 DLM 7-1/4" x 1-1/2" NON-ASBESTOS BRAKE KIT KIT T-221-5 PART NUMBER Roller-brake 1779-P-94 Spring-brake shoe return 2258-Q-719 Brake Shoe and Lining Assy. rear output shaft and output shaft Capscrew-rear output cap Capscrew-rear output cap Capscrew-rear output cap and front output shaft rear cap Washer-rear output cap Capscrew-rear output forward cap. 147. cap. 84. PART NUMBER 1229-K-1597 QTY 36 ITEM NUMBER ON EXPLODED VIEW 68. front output shaft rear cap and case and top cover. 165. front output shaft rear cap. cap. idler shaft rear cap and idler shaft front brg. 138 N-512-1 1229-V-1556 1854-P-146 26-X-54 S-2610-2 1846-E-265 WA-310 WA-36 S-268-2 1 1 1 2 1 1 1 1 22 104 141 156 204. idler shaft rear and front brg. 164. rear output cap.T-221 SERIES SERVICE KITS KIT T-221-4 MAIN CASE FASTENERS PART NAME Washer-input shaft front and rear brg. 147. front brg. cage. 120. 105 1229-E-525 S-267-2 1 9 104 118. 117. case and top cover Washer-input shaft rear brg. . 0.31" O. 0..O.O. shaft nut Washer-P. 0.12" wide.T..O.03" thick. H44 1 1 1 2849-Y-77 26-X-56 A-1805-B-158 28 29 30 31 Tag-oil instruction Plug-P.D.32" wide. H44 1 1 1 1 16-X-40 335 332 4-X-1521 18 19 20 Cotter-shift lever Shaft-P.. .38"-6T spline.75" long. inner Cup P.O.D. H44 1 1 1 2858-T-20 1898-H-34 A-3826-Y-285 H39. H44 H39. carrier to brg. H44 - 2297-Z-6656 14A Shaft-tapered P.T. carrier Screw-shift shaft lockscrew Lockwasher-shift lockscrew H39. shaft brg. grade 8. 0.. single lip. single case.81" O. threaded one end.O.O.O.T. outer Shaft-P. use as required.-P. shaft cap Shim-P. hole.69" shaft. 0. 1.31" long.53" long.T. 4 holes on 3. 0.T. H44 1 1 1 1 1898-C-55 1850-T-150 3-X-161 1229-E-421 32 33 34 Spring-shift lock ball Ball-shift shaft lock Carrier Assy.38"-10T spline.31"-24 UNF.06" long.69" O. shaft Cone-P. 0. slot head. H44 H39. H44 4 4 1 1 S-256P-2 1229-E-1669 1874-A-105 A-3866-S-357 10 11 Gasket-P.D. 3.T. 1. use as required.O. H44 H39. includes item 140. 3.15" O. Not used on models in this book. Retainer. with spring..25" thick. 0. 5.15" O.09" diameter. H44 PART QTY NUMBER 1 1227-L-714 2 3 4 5 Cotter-P. use as required.38" I.D. 9.O.T.00" long.75" across flats.94" O.00"-20 slotted nut. H44 H39.69" O. H44 H39. shift shaft H39. and 36. Not used on models in this book. double lip. shaft nut Flange-input Oil Seal-P. 0. H44 3 3 5 1 1 1 2297-Z-6656 2803-V-568 2803-W-569 2803-X-570 332 335 MPS-4126 - 1 3880-X-336 Key-tapered P. 0. 1. H39. 0.D. H44 H39. shaft cap H39.04" thick.T.38" -16. H44 H39.D.13" diameter.O.O.003".T.O.D. 0. 0. 0.T.38" dia. 0. 1. 0.O.50 coils. H44 H39.T.5"-13.58" I.00" long. H44 H39. 0. Silicone gasket. 1.52"-3 holes.50" across flats.T. shaft MODEL H39.13" dia.T.O. H44 H39. 0.T.O. 1. .44" diameter. Not used on models in this book. H44 1 1 1 1 K-2412 1229-E-1331 3897-N-1002 A-1805-N-352 6 7 8 9 Capscrew-P.T. H44 H39.O.T.O. 0. grade 8.T.38" bore.09" thick.13" drilled hole in 0. shaft cap Sleeve-P. H39. 5. offset lobe in center. Male square head with 0. 1. 1. shaft oil seal Cap-P. 0. H44 H39.T. shaft brg. 0. shaft H39.T. 0.94" wide. outer Cone-P.63" long.T-223 SERIES POWER TAKE OFF ITEM PART NAME 1 Nut-P. shaft H39. single case without spring. included in item 34. 13 DESCRIPTION 1. H44 1 1 1 K-238 2843-C-107 2847-E-291 21 22 23 24 Washer-shift shaft Washer-shift lever stud Cotter-shift lever stud Nut-shift lever stud H39. 1.O. 117.T. shaft Lockscrew-shift fork Oil Seal-P.87" developed length. 0. grade 8.15" pilot. yellow with black lettering.D.D. 0. shaft brg. 1. H44 12 13 14 Cup-P. included in item 34. included pin item 34.010".* . use as required.44" O. 14B 15 16 17 35 * All preformed gaskets are replaced with silicone liquid gasket at time of service. 3. H44 H39.O.53" long.* .D. Includes items 16. inner Stud-shift lever H39. 1. 2. Not used on models in this book.31"-24 thread.50"-20.T. H44 H39. 1.50"-20 thread. Internal tooth type. shaft cap Washer-P. 0. 1. 27. H44 H39. H44 1 1 1 1 1829-J-244 WA-38 K-238 NL-28-1 25 26 27 Fork-P..O. Silicone gasket.31"-18.D. H44 H39.38" bore. 2. 0.50" long. 0.. 0. use as required..O.O.75" bolt circle. Self locking nut 0.005". H44 H39. 0.31" diameter. shaft brg. H44 H39. 0.D. H44 H39.09" diameter.31" diameter. If used omit items 8 and 14.27"-1 hole. 0.O. shaft bearing cage Gasket-P.06" O. H44 H39.. 0.T. 0.53" I. 3826-D-394 cast..56" shaft.50"-13/0. Not used on models in this book.T. shift Lever-shift H39. 2. 1.09" thick. 1. 0. H44 H39.O. 1. 0. 0. 0.. Included in item 34. Elbow-oil intake tube to fitting Tube assy. grade 8. 1. H44 H39. 0. 0. 0. 0. 11.T.D.41" diameter.37" diameter.T.625" O.33"-4 mounting holes.T. 0.D. H44 1 1229-E-421 H39.74" O. H44 1 1 1 1846-V-126 2858-W-101 2297-Z-6656 A2-2847-Q-303 H39.41" diameter. Included in item 64. H44 1 1 A-2847-R-642 1898-J-504 Includes items 63 and 65. 6 drilled holes on 5. 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Capscrew-cage to T-case Washer-cage to T-case Washer-P.F. H44 H39.D. Included in item 52.38"-16. H39.D.49" long. H44 4 1229-E-1669 0.P. 1.38"-16.75" O.35" I.69" O.O. H44 H39. 3826-X-326 cast.. H44 H39. 0..31"-18. 1. H39. 0. H44 H39.44"-13 thread 0.-outlet Connector-oil pump outlet tube Elbow-oil pump outlet tube * All preformed gaskets are replaced with silicone liquid gasket at time of service. H44 1 1 A-3897-T-1762 1898-H-866 H39.D. Includes item 56. H44 6 S-269-1 0.D. H44 H39.T.O. H44 1 4 1898-J-868 S-256P-2 0.D. H39.D. 0.00" long...D. 0.50"-20 UNF 2 holes. 0. grade 8.41" I. 0.62" O. 0.88" long. 0.09" thick. H44 6 6 6 S-268-2 1229-K-1597 1229-K-1597 Internal tooth type. 1.38"-6 spline.19" long.00" bolt circle..00" long..90" long. H39.12" long.25"-18 N.34" diameter.00" long.00" bolt circle..T. 5 dog jaws. 37 Clutch-P.D.T. H44 1 1 1 1898-Q-251 2858-X-102 1898-G-241 0. Included in item 64. 6 tapped holes on 5. H44 H39. 0.38"-6T spline. sliding H39. H44 PART QTY NUMBER 1 PW-210 DESCRIPTION 0. 0.. carrier Ball-pump outlet check valve Spring-check valve Fitting-oil outlet tube to pump Connector-oil pump outlet tube Tube Assy. 1.38"-16. 5 dog jaws.04" thick. grade 8.65" long..25" pipe thread. 0. 24 thread. H44 1 A-1898-W-595 H39. 2. 0.50"-20 thread. H39. 0. H44 H39. H44 H39. carrier to T-case Capscrew-P. 1.38" tube. open end.O. 0.O..41" diameter hole.O.. H44 H39. H39. grade 8. Silicone gasket. H44 H39.. 1 angle drilled hole.50"-20 thread. H44 1 2848-J-88 38 Capscrew-drive clutch retainer Lockwasher-drive clutch retainer Retainer-drive clutch Clutch-P.75" O. 0.* 0. 0.41" I. 0.2 coils.T-223 SERIES POWER TAKE OFF ITEM PART NAME 36 Plug-expansion MODEL H39. H39. 3 coils 0. carrier to T-case Plunger-oil pump Spring-oil pump plunger Gasket-oil pump to carrier Oil pump-body assy.48" long.75" O. carrier Washer-oil pump to P.38" O. H44 1 1 1 1228-K-37 2858-X-102 1898-K-531 H39. H44 1 S-267-2 H39. H44 1 1 1 1829-D-680 2848-H-86 3826-X-284 H39.75" dia. 90 degree elbow. 0.D.D. 0. use as required.-intake Fitting-oil pump to intake elbow Ball-inlet check valve Spring-check valve Connector-oil pump intake tube Fitting-intake tube to case Capscrew-oil pump to P. H44 1 1898-J-504 0.062" thick. H44 1 1898-L-532 0.34" I.25" pipe thread. 15 . 24 thread.75" long. H44 H39.T. includes external shift groove.75" long.D. drive Cage-input shaft rear brg. 0.25" O. 3 coils 0. H44 H39.06" thick. H39. 8 balls.29" O.12" long.75" O. 15T spline.00-1) 75 Washer-direct drive gear 76 Gear-low speed sliding (1. E23. A104.. 1 A-3892-R-1604 27T. spur. A103. 1 spline 1. spur. C20. 5.. A90.-direct drive (2. 3.D. 27T. L. 1 3892-X-2442 1 3892-W-2441 1 MPS-4122 15T.61" I. standard. 0. A99.38" O.D. with shift groove. E22.71" O. 70 71 71A 71B 72 73 74 Gasket-input shaft rear cap Bearing-input shaft rear Cup-input shaft rear Cone-input shaft rear Washer-input shaft rear brg. All except transfer cases equipped with PTO. 1. standard.D. 5. 1.00" bolt circle. 1. with shift groove.-direct drive (1. A89. C43. A99.* 0. C44 C31. available as assembly only.75" O. A90. with shift groove. with shift groove. 3. Helical. 3. 2 inside angle drilled holes.. f Replace with items 71A and 71B.87-1) Gear-low speed sliding (2... A92. 27T.23" O.. g Non-serviceable item.. available as assembly only. includes 17T spline. split. A91. 1. C30.. A88. A94. 12.05-1) Gear Assy. C20.16" thick.D. not sold separately.D. All others 1 A-3892-L-1806 All 1 1829-P-380 A84. includes item 73. E23 (Continued) * All preformed gaskets are replaced with silicone liquid gasket at time of service.. 1 spline 1. Silicone gasket. includes item 73. A89. 2 tapped holes on 5.2.T-223 SERIES MAIN CASE ITEM PART NAME 67 Capscrew-input shaft rear bearing cage 68 Washer-input shaft rear bearing cage 69 Cage-input shaft rear brg. C41. All 6 1229-K-1597 0. standard.00-1) Shaft-input MODEL All PART QTY NUMBER 6 S-268-2 DESCRIPTION 0. Must service with direct drive gear only 17 .H. input spline 1. 14T. includes item 88.D.47". 12.D. includes item 73.37"-6T. spur. 15T spline. C34. R. 0. All See remarks All All All All 1 3838-N-196 1 1 1 1 1 2297-Z-6656 1228-S-409 f 332 339 1829-S-721 1825-R-200 g 1 A-3892-J-1544 1 A-3892-W-1635 3828-Y-311 cast. 2 holes and 4 grooves. includes 15T spline. A105.50"-10T. 17T. M4 All others 1 3892-Z-2444 27T. standard. spur. includes item 73. A103. Helical. A84. A103.53" diameter. 2. includes 16T spline.-direct drive (2. A98. A91. 3. standard. induction harden spline 1.D. 5. E22. A91. C22. 6 drilled holes on 5.23" O. heavy duty. A104. A94.18" thick with 4 slots.D.D.50" diameter. M4 A84. C22.. C41. 0.78" wide..39" I. E22.15" O. 5. 3. 15T spline. C32. C34. C22. A90.00" long.D. L.64" I. heavy duty.D.D.13" long. C43. C32. 1.25-1) Gear Assy. A98.D. spur..23" O. standard. L. included in item 74.. A94.H.41" I. Helical. E23. A88.71" O. 15T spline.48" O.87-1) Gear Assy. 4 splines.23" O. A92. use as required.09" thick. 1.05-1) 77 Gear-low speed sliding (2.25-1) Gear-low speed sliding (2. Helical. 14T spline. C30.-direct drive (2.91". A104. Input bearing journal 1..H. high gear thick/ thin over all dimension 1.D. C44. 2. 0.00"-15T. 1 3892-Y-2443 16T.H.31" O.D.38" bore. closed.38"-16. C29. A105.. A99.00" bolt circle..57". 2. Bushing-direct drive gear Gear Assy.D. C29. grade 8. 1. A88.. A105 A98.22" I. 3.D. 37"-6T. 2 notches 85 degrees apart.50"-10T.2.005".. C22.84" O. 1 2 1229-E-3047 2803-L-1832 2 2803-M-1833 4 2803-N-1834 2 2803-B-1874 6 2803-C-1875 1 2803-D-1876 2. A94. A90.005". 0.010". 4 splines. A98.D. 3.. use as required.54" O.D. A92. 3. E22.. A88. C31.T-223 SERIES MAIN CASE ITEM PART NAME 77 Shaft-input 78 Spacer-input shaft 79 Bearing-input shaft front 79A Cone-input shaft front 79B Cup-input shaft front 79C Washer-input shaft front 80 Shim-input shaft front bearing cap MODEL A89 PART QTY NUMBER 1 MPS-4124 A94. includes item 88.. 1 1 376 353 1.57" I. A89. E23. C31. E23.003".50"-10T. .76" I.D.D. 1. 1 spline 1. A99.12" O.D. 3. A88.00" long. 0.D. includes item 88..75". use as required.94" O.00" long. A89. use as required. 2. 0. C30. A105. A104. 1. C41 C43. . A91. A88. use as required.69" diameter. 3. A98. 12.34" diameter induction harden spline length 3. E22. 2 notches 85 degrees apart.78".. 4 splines. 1..2. A89. input bearing journal 1. 3.06" O.75". No induction hardening on spline. 1 spline 1. A89. E22. A104.47" in thick spline area. M4 All others A84.75"-10T.25".37"-6T.13" thick. A92. 2.57". Induction harden 1.94" O. 2 notches 168 degrees apart..60" I. A98.60" I.. C34. 3. E22. 2 notches 168 degrees apart. A99. A103.00"-15T. C41. . A99. .. 1.D.D..37"-6T. . A99. A88. 1 spline 1.D.2.D. E23. A91.60" I. A105. C32.D. A105. 1 spline 1. 1 1229-F-2814 2.77" wide. A92..13" long. (Continued) 19 . A103. C29. . 1 spline 1.D. A91.60" I. Input bearing journal 1.010".D. C43.59" I. includes item 88. use as required. 8 balls. A94.125" thick. A103. 0. C29. M4 C20. C22. M4 All others A84.77" I. E23 M4 1 1 1 1844-C-809 1228-R-408 357 DESCRIPTION 12. includes item 88. 1. A92.60" I. A94.D. 4 splines. 1. input spline 1. C44 All others A84. 1 spline 1. A90. C44 1 MPS-4120 M4 1 MPS-4123 All others 1 MPS-4121 A89 See remarks A84. Same as MPS4122 except high gear thick/thin spline over all dimension 1.00"-15T. C22. A104. 12.D. 2 notches 85 degrees apart. C20. use as required.60" I. input bearing journal 1.003".06" thick.D. A90.D. A105. 1.51" I. A103.51" I. A91. 2 notches 168 degrees apart. A104. C22. A90.00"-15T.. 1 1 372 1229-F-3048 3.D. C30. 3. 2. 0.. . 0. 0. includes item 86 (R-408).75" bolt circle. C34. cast in oil slots approx. C30. H46.. Hex socket-female. C41.50" wide. available as assembly only. 5. A91. H52. A105. A99. A98. C31. 6 2803-H-1932 4 2803-J-1934 A84. H53. M4 C20. C43.P. C44 A103. H46. with spring. H54.87" O. N4. 3.D. E22. H41.T-223 SERIES MAIN CASE ITEM PART NAME 80 Shim-input shaft front bearing cap (continued) 81 Cap Assy-input shaft front bearing cap 82 Plug-input shaft front bearing cap 83 Washer-input shaft front bearing cap Capscrew-input shaft front bearing cap Plug-input shaft shipping cover Oil Seal-input shaft front bearing cap 84 85 86 86A Washer. use as required. E22. A90. 2. A92.25" shaft. A84. C32. 1.12" long. A88. 6 holes.D.S.94" bearing bore.. A94. 3. uses item 86 (R-408). A104..25" bolt circle.13"-27 N. A90. A104. A103. C31.87" seal bore.87" seal bore.D.12" O.25" O.D.55" bearing bore.09" thick. H48 M4 1 A1-3866-X-804 1 3866-C-757 All others 1 A-3866-X-804 A98. C22. C41. E23 A85.D. All 6 S-269-1 0. C44. same as A-3866-X-804 except item 86 is A-1205-T-1242. 2. C20. H57 All 1 P-42 3866-C-757 cast. E23. H36. double lip.13" shaft. C43. C34. C32. C29. use as required. . 1.003".38"-16. 3866-B-1250 cast.D.. A92. C32. 4" I. 0. 6 holes. A94. same as S-721 except has 1 drilled thru hole 0.63" O.D. C22.. H55. 4" I. . No longer available. H56. 6 1229-K-1597 0. 2.D. 2.41" I. 67 degrees apart.D.. 6 holes 3. 2. 0.010". 1. C44. 1 A-1805-A-573 C41.75" O. tap thread.D. A99. A105 1 A-3866-S-721 1 A-3866-Y-935 C20. 3866-B-1250 cast. C29. C30. H48..51" I. C41 All others 1 A-1805-R-408 2. use as required. A104.D. 0.51" I. double or single case with 8 spring.00" seal O.84" O. 5. H40. H31. A88.D. 4. 4" I.06" thick. 5.D.00" seal bore.125"-27 thread. A98.. thrust MODEL All others PART QTY NUMBER 2 2803-G-1931 DESCRIPTION .D. 0. 0. double case with spring. 3866-Z-1274 cast. replaces A-1805-S-409 with single lip. H47. 2. A89.D. C29.125" thick. cast in oil slots about 168° apart.F.13" tapped hole. N7 1 PW-226 1. double lip.55" bearing bore.D. A104.25" O..44" wide. 1 A-1205-T-1242 3. A105 1 1 1229-F-2814 1229-F-3048 3. grade 8. 3. C43. A99. double case. A91.12" shaft. C31. 4. 1..25" bolt circle. 4. 0.48" wide. available as assembly only. 0.00" seal O. 21 . 3866-Z-1274 cast.25" O. A89. includes item 86 (A-573). A105. H47.005". includes item 86 (R-408).. double lip. H33. 56" at 80/100°. 4 holes.02" I.T-223 SERIES MAIN CASE ITEM PART NAME 87 Washer-input shaft 88 Nut-input shaft 89 90 91 Cotter-input shaft nut Deflector-input yoke Flange/Yoke-input 92 93 Flange/Yoke-rear output Deflector-rear output yoke MODEL A84. 1410/ 1480 flange. A103 1 3260-H-1256 A92. 4. A91.31"-24 UNF on 2. 1. 4 holes.75" bolt circle. 0. C31.75"-10T spline. 4 holes 0.75"-10T spline. E23.22" long. A92. 4 holes at 80/100°. 4 holes.50"-10T spline.D.16" thick. . 1350/1410 flange. C29. 0.45" diameter. drilled holes for mounting u-joint. A103.75"-10T spline.25" at 80/100°. 4.50"-10T spline.75" bolt circle. 1500 flange. 0. 1550 yoke.25" thick. drilled holes for mounting u-joint. 1.07" bolt circle. 4 holes at 80/100°.D. 4. A90. 1600 flange. 1.75"-10T spline.31"-24 UNF on 2.00" O. H52 1 3897-J-1440 E23 1 3897-M-1729 H41 1 3897-P-1966 H47 1 3280-S-7897 A98. 1. 1.. A104. 2.56" at 80/100°.D. 4 tapped holes 0. 0.50"-10T spline. 1. 1410/ 1480 flange. 1.75"-10T spline. 3. included in item 77. H55. 1.823" I. M4 1 2WCS24-43 C34 1 3897-K-1441 E23 1 3897-L-1728 H41 1 3897-P-1966 H47. 3.75"-10T spline. M4 1 2WCS28-32 C34. 3. 1. 1480 yoke. 0. 1550 flange. 1550 yoke. 1480 yoke.75" bolt circle. 1. 1.13" diameter.D. 4 holes 0. 4 holes.47" on 4.25" at 80/100°.00"-20. 1550 yoke. H57 H52 All others All PART QTY NUMBER 1 1829-V-100 1 1 1 1 1829-M-585 1229-C-4553 1229-E-1331 1227-C-939 All A89 1 1 1 K-2412 2847-P-640 3897-L-1962 A90 1 3897-Z-1794 A91 1 2WCS24-81 A92 1 3897-Q-1369 C20.63" apart. A89. A105. A88. 1. M4 H56. 1600 flange.. 4.45" diameter. 4 holes 0.75"-10T spline.22" long. Not used on 223 models in this book.23".75"-10T spline.. H57 1 3897-R-1370 C20. 3.75" bolt circle. 0.75"-10T spline.13" bolt circle. C41 1 1 2847-P-640 2847-S-617 23 DESCRIPTION 1.25" seal O.D.75"-10T spline.13" bolt circle. 1. 1550 flange. 4. C43.69" apart.63" apart.50"-10T spline.75" bolt circle. 1. H56 1 3280-S-7897 H52 1 3897-J-1440 H57 1 3897-R-1370 A89 1 3897-K-1961 A90 1 3897-Y-1793 A91.D.75" bolt circle. 1. 1. 4 holes 0.50"-10T spline. 8 holes on 6.81" O. 3. 2.250" thick.D.03" I. 2 slots 0. 1.03" I. 4 tapped holes 0.48" O. 8 holes on 6. drilled holes for mounting u-joint.. Not used on 223 models in this book. 7C yoke. 4 holes 0. 4 holes 0. 1410 yoke. 1. 4.312" width across flats. 4.75" bolt circle.31" bolt circle.75"-10T spline..75" O. 1. 1. 1. 7C/ 72N yoke.D. 4 holes at 80/100°.50" long. E22.D.. 4 holes 0. C32. C20. C30. 4. C44.68" apart. A99. 1. 1500 flange.22" long. C41.50"-10T spline. 4. 1.217" thick..07" bolt circle. 1. 1550 yoke. 1. 81"-20 UNEF male thread other end. included in item 112. C30.F. C32. Helical.50" bolt circle. A104. A88. 0.D.44" flange O.81"-20 UNEF male thread other end. C31. H39. A98. A105. C43. M4 A91.03" flange width. 0. A103 1 1898-U-671 1 1199-N-1106 C34. H41. 0.. A103..88" nut. available as assembly only. A94. 4th hole 2.88"-18 NS male thread one end.41" I. 1.D..25" shaft.31" thru-hole. threaded hole.250" thick.81" O.00" seal O.09" thick.88"-18 NS male thread one end. H55.25" I. A88. . C41. double case.. 2.D. 1. C20.D. 0.D.P. E23. 0. A91. grade 8. H52. 0. 3866-E-733 cast. same as E-733 except add 0. H40.31" O. 0.73" O. C43.73" O.D.25" thick. A89.D.88" nut. H44. C29. H52. A92. A103 1 1898-V-776 1 3891-C-1849 A84. A98.75" O. C29. C20.312" width across flats. 15T. H43. Metal threaded plug.D.34" wide. 0. A98. M4 All others 1 A-3866-E-733 1 A-3866-G-891 All 1 1199-M-1105 A84.03" I.50" long..D. 2.56" from center..D.81"-20 UNEF male thread other end. 0..D. 1.D. 0. A99. A90.48" O. 0.D. C41. double lip. H53.D. 0. 0. replaces A-1805-S-409 with single lip only. C34.44" width. 0. 0. included in item 97. M4 A91. H56.41" I. 0. 0. H57 A85. H53. H47. replaces 1850-Z-104 plastic plug. A105. includes item 96 and 98. A99. 0. A92.. included in item 97.88"-18 NS male thread one end. 0. H39. C32. H40. A90. 0. 1. 0. E23. 0..50" wide. 3.38" thru-hole.13"-27 N. 0. H48. open end.823" I. includes item 96 and 98. available as assembly only. A88.00"O. C20. A89. Flanged. H55.. C34. with spring. speedometer gear on shaft. 3 holes on 4. A99. 0. C44. A89. H57 H52 All others All PART QTY NUMBER 1 1227-C-939 1 1829-M-585 1 1 1 1229-C-4553 1229-E-1331 A-1805-A-573 A84. E22.-rear output shaft 98 Bushing-speedometer driven gear 99 Gear-speedometer driven 100 Sleeve-speedometer driven gear 101 Plug-speedometer hole 102 Cotter-rear output shaft nut 103 Capscrew-rear output cap 104 Washer-rear output cap MODEL All A103.00"-20. H42. 0.. A104. A104. 1. Helical.S. 0. 14T.D.38"-16.. H57.02" I. speedometer gear on shaft.. 0.D.12" long. H55..38" wide. C30. H56 All All All 1 2245-X-50 1 A-1850-R-18 1 4 4 K-2412 S-269-1 1229-K-1597 25 DESCRIPTION 1. 3866-F-1254 cast. 0. 0. H33. 0.217" thick.47" thru-hole. C31. A99. H33.T-223 SERIES MAIN CASE ITEM PART NAME 94 Nut-rear output shaft 95 Washer-rear output shaft nut 96 Oil Seal-rear output shaft 97 Cap Assy. 0.. C44.50" O. 1. 0. 1.13" diameter. E23. A104.T. grade 8. 0.83" O. A105.27" O. H41. H55.. . use as required. H33. 1 1844-J-166 2. H53.. C31.. H33. 1. A88. All 1 3892-P-1550 112 Shaft-rear output All 1 MPS-4118 113 Cone-rear output shaft forward bearing 114 Cup-rear output shaft forward bearing 115 Shim-rear output forward bearing All 1 25878 27T.13" O.D.005". C23. C30. 1.D. H46. 1. Helical.09" thick. C29.88" O.P. H39. A99. M4 A85. 0. A103. H33. C43.003".D. H56.D. H36.D. C30.41" I. use as required. L.T-223 SERIES MAIN CASE ITEM PART NAME 105 Breather-rear output shaft rear 106 Gasket-rear output cap 107 Gear-speedometer drive MODEL A98. 3. H57. replaces 3866-S-773 with 2 flats on O.D.38"-16. 0. H47. C23.010".D. All 1 25821 2.D. 2.38" bore. threaded one end. All 4 1229-K-1597 0.03" long. 5.H.38"-16. C31.* 4T. C43.75" O.76" I. H31. H53. H40.D. C44.76" I. C41. A89.. H40. 0.. A89. H40. A91.13"-27 N. H39. Helical. 1.D.. C44.D.12" long. 1.D. grade 8.13" O.D.F.09" thick. C30..D. C34. 0.63" bolt circle.. H41 A84.00"-10T spline.75"-10T spline. 1 1844-S-565 2. 108 Spacer-rear output shaft 109 Cup-rear output shaft rear bearing 110 Cone-rear output shaft rear bearing 111 Gear-rear output shaft * All preformed gaskets are replaced with silicone liquid gasket at time of service. 0.22" O.41" I. M4 All PART QTY NUMBER 1 A-1199-C-1043 DESCRIPTION 0. H47. C34. H57. H48 All A84.79"-10T spline. use as required. 1 25520 3.. All 1 25584 1. .75" I. A103. H55. All 116 Cap-rear output forward All 2 2 4 1 2803-Z-1846 2803-A-1847 2803-B-1848 3866-C-731 117 Washer-rear output forward cap 118 Capscrew-rear output forward cap 119 Capscrew-idler shaft rear cap 120 Washer-idler shaft rear cap All 4 1229-K-1597 . 1.42" wide. C31. A92. C29. 1. 4 holes. A104.12" long. Stamping. 27 . on O. 0. 1.. no flats. H52. C32. 1 2297-Z-6656 1898-S-799 Silicone gasket. C29. includes item 94. 11. A88. A98. C30. C32. All 4 S-269-1 0. 2. H47.. H39. H52. C41.18" wide.75" O.5" long. 1.75" wide. A91.. use as required. H44.. C34. All 4 S-269-1 0.D.71" bore. A104. C32. A99. E22. 1. A99. C29. A89.38" I.88" O.* Fits over 1. includes 1. 1 3892-T-1606 1 3892-K-1805 A84. includes 1. C31.50" O. A94.. H47. with no flats on O. R.H. M4 All others 1 1 1844-L-480 3892-B-1640 1 3892-Y-1637 34T. spur 6.88"-10T spline. M4 All others 1 31597 7.30" long. E22.05-1) Gear-low speed (2. standard. 1.D. H46. H54. 1.88"-10T spline. C22. spur 7. 3. heavy duty. H47. A104. C34.00-1) 129 Shaft-idler 130 Cone-idler shaft front brg. round O. A88. C32.28" O. H48. H40. H33. bore.88"-10T spline. A104. spur 7. H53.44" bore. replaces 3866-S-773 with 2 flats on O. M4 All others 1 3880-U-723 35T. H54. A90. A88.D. 1.D. . 7. 1. standard. 1. * All preformed gaskets are replaced with silicone liquid gasket at time of service.25-1) Gear-low speed (2. A105..63" bolt circle. C22. 1 HM-89449 1. A98. A91. C34.94" I. A89... C44 A94. A89. H52. C34. A95. H55. A103. includes 1. C31. A91. 29T. H41. H46. includes 1. A88. H48. 1. C43. C30.28" wide. 28T. 4 holes.88"-10T spline. 3. H44. A92. H31. A98. H52. H31.88"-10T spline. A98. A92. A104. C41. use as required. C20. C22. H47. H36.88"-10T spline. H56. A103.00" O. C32. A105 A92. 1 3866-C-731 All H29. A90. C41.08" O. closed end. A94. A105.D. H40..D.88"-10T spline. E23. spur 7.44" bore.T-223 SERIES MAIN CASE ITEM PART NAME 121 Cap-idler shaft rear 122 Gasket-idler shaft rear cap 123 Snap ring-idler shaft 124 Cup-idler shaft rear brg..D. E22..87-1) Gear-low speed (2.44" bearing diameter both ends. A94.D. 2. H44.D.D. H41. H39. standard.D.D. C30.44" diameter shaft. 33T.06" O.. C43.63" bolt circle. 5.50" long.44" bearing diameter both ends. closed end. 125 Cone-idler shaft rear brg. 4 holes. C43. Reference TSA-4-43 for further technical information.. E23. C20. Helical. H46. H57 All All All 1 2297-Z-6656 1854-E-187 1 1 1 31521 31597 3892-C-1641 All A84. A99. H36. H56. H33. C44. A94. MODEL H29. 1 3880-A-807 A84. A103.D. A90. includes 1. A99. 1. Silicone gasket. H39. C32.41" O. H55.. 126 Gear-idler shaft 127 Spacer-idler shaft gear 128 Gear-low speed (1. E23. C41. C30. C20. C44. 3. H57 All others PART QTY NUMBER 1 3866-N-794 DESCRIPTION 3866-M-819 cast. C31. C29. 1. A99. C29. with scallop and 2 flats on O. 29 Stamping.. E22. H48. A91.D. C44.91" long. H41. A104.16" thick. A94. 2 flats. H48.63" bolt circle. C44. H46.D. C34. H44.41" I. use as required. C20. H46.19" thick. H31. included in items 14 and 155. MODEL A84.13" diameter. H55.D. H44.38"-16. 2 10-X-1292 0. H39.. C20.03" I.D. A105.00" O. A89. Stamping.D. H53. H39. with scallops. 1.88" bolt circle. A99. A98. A92. no flats on O.. H55. cap 136 Cap-idler shaft front brg. A88. 0. H52. C29. H52. round O. . A105.75" O. C22. H39. H56. H36. A104. H55.010". H44. H54.D. C30.75" O.D. H56. A88. 0. 1.88" long. H33. H48. C31. 4 holes on 3.. 1. H53. H48. C29. 3. 3. H48. washer 134 Lockwire-idler shaft brg. A92. H46. 0. H31. 137 Washer-idler shaft front brg. C22. A103. with 2 holes 0. use as required. 1 LW-163 16 gage.312" width across flats. 0. A103. 1. H46.D. H36. . H54. 1 hole drilled in head. 1. H57 All A84. C41. 3. M4 All others H29. C32. A91.00" O. H41. E23. A98. H40.D. 1. 0. E23.00" long.005". A91. H54. 1 3866-N-794 3866-M-819 rough part. 0. H57 H29. . C43. C30.00"-20. C43.50" long. 133 Capscrew-idler shaft brg. use as required. H53.63" bolt circle closed cap. H47.D. C31. C41. C34. grade 8.. H36.09" thick. H57 H29. E22.39" diameter on 0. 3. 1. A94. 2 2 4 1 2803-Z-1846 2803-A-1847 2803-B-1848 3866-C-731 . 138 Capscrew-idler shaft front bearing 139 Cotter-output shaft nut 140 Nut-output shaft All All 4 4 1229-K-1597 S-269-1 All All 1 1 K-2412 1227-C-939 141 Washer-output shaft All 1 1829-V-100 31 0. H40. grade 8. H40..D. . H41. M4 All others PART QTY NUMBER 1 31521 DESCRIPTION 0.94" long. washer 135 Shim-idler shaft front brg. H47.75" O.38"-16. replaces 3866-S-773 2 flats on O.T-223 SERIES MAIN CASE ITEM PART NAME 131 Cup-idler shaft front brg.12" long. H31. H52. H47. E22.003". A90.. H47. A90. 4 holes. C32. H33. 132 Washer-idler shaft brg. 0. H33. 1 1 HM-89411 1829-H-788 0. A89. H56. H39. H36. 2.68"/ 1.56" at 80/100°. H56 C20. C30.D.50"-10T spline. 1. H33.09" thick. C29. C31. C44. H55 1 145 Deflector-front output yoke H56 H47 1 1 146 Capscrew-front brg. H54. C31. with snap ring.D.13" bolt circle. 0. C30. 3. 2WCS24-81 1550 flange. includes item 148. C43. 0. 4.31" long. C31.38"-16. H56 C20. 1. 155NYS24-6 1550/155N yoke. use as required. H29. H39. 0.97" both ends.12" shaft.D.. 2WCS24-43 1500 flange.D. H48. grade 8.57" I. grade 8. 3. grade 8. 1229-K-1597 0. 0. A1-3280-R-7896 1550/155N yoke..07" bolt circle. 0. H32. 1.87" long.62" high.. H46. 4 holes at 80/100°. H36.D. included in item 149 and 155. H53.D. H39.75" O. 4.50"-10T spline. H29.41" I.* All 1 1828-V-74 C20. H41. 0.15" O.09" thick. H29.38"-16 thread. 0. 0. 152 Oil Catcher-output shaft 153 Washer-oil catcher * All preformed gaskets are replaced with silicone liquid gasket at time of service. C34.75" bolt circle dia. H44. H32. 2297-Z-6656 Silicone gasket. H33. A-1805-R-408 2. M4 1 C34.46" I. H36.. 4 holes 0. available as assembly only.T-223 SERIES MAIN CASE ITEM PART NAME 142 Capscrew-oil catcher 143A Locknut.50"-10T spline.-output shaft front All 1 150 Gasket-output shaft front cap 151 Bearing-output shaft front All - 7C yoke. C34. C43. 4 holes 0. cap 148 Oil Seal-output shaft front All All All 4 4 1 149 Cap Assy.50"-10T spline. 1. 1. C41.D. C44. H52 1 E23 1 H47. cap 144 Flange/Yoke-front output MODEL C20. H44 A90 PART QTY NUMBER 1 10-X-830 1 NL-26-1 1 1229-K-1597 1 3897-Z-1794 DESCRIPTION 0.D. with spring. 0. 1 WA-36 0.81" O. 0.D. H29.50"-10T spline. . includes item 145.. 0. A-3866-B-730 3866-D-1292 cast. H46.. H56 C41.31"-24 UNF on 2.12" long.D. 3897-Q-1369 1350/ 1410 flange. 4 holes 4. 4 holes on 4.50"-10T spline. cap 147 Washer-front brg. H53. 3897-L-1728 1550 yoke.44" wide. C32. H48 C29. H33.06" thick. C43. 33 Ball bearing. C30. 2297-S-695 "S" shape (cross section).50-10T spline.75" O. 1. H44. A91. 1.75" bolt circle. H54. H36. H33. H54. 1. C32. C44.88" wide.75" bolt circle. 4 tapped holes 0. 1. H44. 1.. double lip.50"-10T spline.63" apart.41" I. 1. S-269-1 0. H39. H57 1 C20...D. A103 1 A92. 3897-K-1441 1410 yoke.56" width across flats.71" wide.50" at 80/100°.18" I.13" seal O. 2. 1.D.. H53.38"-16..88" O. 1. C32. C34. H46 1 2847-Q-849 1 3221-S-19 3. 2. C41. 2. included in item 144. oil catcher capscrew 143 Washer-front brg. double or single case. 0. 3.56" wide at opposite ends.44" O. M4 1 A-1805-P-536 A91. C31. Included in item 155. C30. C30.88"-10T spline. 1 K-236 C32. 1 MPS-3831 A90. H55.50" wide. A89. double lip. H55.T-223 SERIES MAIN CASE ITEM PART NAME 154 Pin-oil catcher 155 Shaft-front output assembly 156 Snap Ring-front output shaft 157 Clutch-front output sliding 158 Gear-front output shaft 158A Bearing-needle. A103. E23. C32. H53. 1. 11. C34. includes 16T external spline and 23T internal spline. A99. H53. A103. 148. 157B. 1.D. A94. A105. 1. two bearing journals at opposite end. A88.88". A104.91" long. H31. H57 DESCRIPTION 0.17" I. H33. 2.25". 2..09" diameter. H33. C22. A94. 157A.19" I. two bearing journals at opposite end.49"-10. C43. .. H33. H56. O.92" O.. 2. C43. H52. M4 A98. outer journal 1. H46 A84. C34. C22. H44. 155. C31.D. replaces A-1805-R-356 with single lip only. 1. A91. L.50". H39. inner journal 1. H54. C18.D. 5. 35 23T. E22. H48.. H29. H47. outer journal 1. C29. O. H48.D. C29. 1 2297-Z-6656 Silicone gasket.D. E23. thick/thin external spline. H36. outer 158B Bearing-needle. 0. Includes items 155. C31. I. Includes items 140. 0. double case with springs. has external shift groove. A98. A104. A89. 158.D.* * All preformed gaskets are replaced with silicone liquid gasket at time of service. H44. 171. H47..50".75" long. C32 C34. E22. C23. H57 All 1 1244-Q-1629 2. 157B and 158. A92. H40. H48.D. 1. H47. 2. A88. H53. C32.50".. use as required.23" O. and 197B.00" length. 1"-20 thread one end. 168. H54. inner 159 Bearing-front output shaft rear 160 Oil Seal-front output shaft rear 161 Spacer-front output shaft 162 Gasket-front output rear cap PART MODEL QTY NUMBER C20. 3.D. H29. C41. H29. C31. Helical.D. 157A. C29. H40.50".25". H55. Ball bearing. H52. H46.49"-10.91" long.25".D. 11. 0. A103. C30.63" shaft. A90. 0.D. spline at threaded end 1.82" wide. H57 All 1 1254-M-91 1 2848-E-161 All 1 MPS-4217 All All All 1 1 1 1228-B-1380 1228-A-183 1828-S-149 A84. C41.94" O. 160. H41. H39.25" wide. C44.62" O. H56. H46.. A105. 1. 27T. H41. 156.50" O. 2. A99. 1 MPS-4217 A105. A104. C20. H36. included in MPS-3831. 1"-20 thread one end.88" length. I. inner journal 1. H31. 156. H36. C34. H46. H44. H39. spline at threaded end 1. 3.H. C20. with snap ring. Included in item 155 (MPS-3831). A92. . H57 All others H29. 4. 1. 0. H29. M4 H29. H46. M4 A84. H36 6 S-2610-2 0.D. 4. 6 N-16-1 0. H41.38"-16. A88. C43. H52.50" O. C44. E22. C30. C31. H57 A99. H41. H36. grade 8. H53. available as an assembly only. H54. H53. 1 3897-F-1332 5. C32.08" thick.75" O. H44. H52. H33. A90. H40. A105. 5. C44. H40...75" bolt circle. H56. C22. C22. H33. 6 holes.-front output shaft rear 164 Washer-front output shaft rear 165 Capscrew-front output shaft rear 166 Stud-rear output shaft 167 Nut-rear output shaft 168 Expansion Plug-front output shaft 169 Hub-brake 170 Snap Ring-brake hub MODEL A84. H31.D.12" diameter shaft. includes item 160. 3.88" bolt circle. are equal distance. H40. H54 H29. A89. H36. 6 drilled holes on 4. E23. C29. H46. 2. grade 8. 2. H55. C31. A105.81" long.D. includes item 160.38"-24. A92. Included in item 155. A104. H47. H36. 1. Available as an assembly only. A88. 3866-E-1253 cast.56" O. A98. H39.41" I. C30.D. H54 A84.78" long. A94. H56. C30. A99. H44.12" long. A103. C32. same as C-887 except 4 additional drilled holes on 4. C31. C41. C41.38"-16 both ends. includes item 160. H53 All others 1 A-3866-R-1162 1 A-3866-D-732 All 6 1229-K-1597 3866-E-1253 cast. H54. H54 A91. H36.31" bolt circle on either side of slot on O. A99. 1. A89. C43. 1 3266-Y-857 1 A-3866-W-777 H29. A92.16" thick. C34. 1 PW-225 1.D. included in item 155.56" O. 6 and 4 holes.50" bolt circle.D. H39 PART QTY NUMBER 1 A-3866-C-887 DESCRIPTION 3866-E-1253 cast. Fits over 2. grade 8. 1 3897-R-3008 1 1854-W-257 6. C34.25" long.38"-16. C44. A90. All 37 . C29. 0. A104. H55.. H31. 6 6 S-269-1 4-X-840 0. H53. C41. are not equal distance. C29.. Same as W-777 except drilled holes on sides of slot on O. 1.82" long. C20. H42. C43. H46. H39. includes item 160. E22. H48. C34. C20. A94.09" thick. 3866-D-732 cast.D.53" long.T-223 SERIES MAIN CASE ITEM PART NAME 163 Cap Assy. 0. 0. 0. E22. E23.31" long. holes. 4. 39 . H53. A98. 5875-P-432 casting. W and Z mounting bosses. included in item 155. 5875-Z-468 casting. 0. cup shape. A92.63" bolt circle-4 holes each. C44. Y and Z mounting bosses. 5875-Z-520 casting. A92. A105. 5875-K-453 casting. C44. 5875-P-432 casting.13" bolt circle4 holes. 4.T-223 SERIES MAIN CASE ITEM PART NAME 171 Expansion Plug-brake hub 188 Case-transfer 189 Name Plate 190 Screw-name plate 191 Expansion Plug-shift shaft MODEL A84. 1 PW-214 0. H52. disc shape. C20. A89. H55.30" diameter.08" thick. hole size 0. and Z mounting bosses. H33. E23. 1 3875-Q-433 1 3875-K-531 A91. 0. H47. A105. H48.25" length. 5. C41. H52. H57 All others 1 2 1 1199-K-1493 9-X-16 1199-K-3287 5875-P-432 casting. 1. H41. W and Y mounting bosses. A89.05" thick. H46. E22. same as Z-884 except with interlock notches different bore size at input and tapped hole for oil. 4. A99. C31. 3. C41. and Z mounting bosses.25". 3. H54. A90. C22. C34.38"-16. C30.63" bolt circle 4 holes.. W and X mounting bosses. E23 1 3875-A-469 H31 1 3290-G-1073 All others 1 3290-E-1071 All All C20. H29. offset with interlock notches. A94 A85 PART QTY NUMBER 1 PW-252 DESCRIPTION 3. A104. H36. W and Y mounting bosses.T. H31.32" diameter. W and Y mounting bosses. 2 holes 1. 3875-Z-520 casting. with pump and oil level hole location. H39. 0.134" thick. same as Q-433 except for oil level and drain location.25" bolt circle-6 holes.88" bolt circle 6 holes. A103 1 3290-Q-1005 A98. W and Y mounting bosses. same as Q-433 except for drain and oil level hole location. less interlock notches.25" O. 4. A88. A104 1 3875-Z-884 C22 1 3875-V-438 C34 1 3290-R-1084 E22. H44. 0. H53. C29. W. 5875-P-432 casting. H56. M4 A84.O.38"-16 dia.50" bolt circle-4 holes. 2 holes 3. C43.00" x 1. A94. A88.D. C32. 5875-K-453 casting.H. C31 1 3290-F-1072 A99. W. W and Z mounting bosses. Y. same as Q-443 except for drain and oil level hole locations. Y. same as Q-433 except tapped hole for P.00" bolt circle-6 holes. L. disc shape. same as Q-433 except with interlock notches and reposition holes for clocking brake. 5875-P-432 casting. A90. H40. W. same as Q-433 except oil fill plug 15° below output gear center. H33. H47 All others A84. H52. C29.00" long. C43. A98. female square socket. square socket. C20. 0. H52. H57 C29 1 1250-G-475 DESCRIPTION Non-magnetic. 2. C30. H53. 0. 0. H48. A90. C41. square head. 0. C31. cap plug. 0. H32.75" long. 1 1850-T-150 A103. Male. H33. C31. C32. H31.T..T. H53. C31. A94. H53. 3. H40.50" long. M4 H29. C34.75"-15 thread. A90. H40.75"-14 thread. not available at this time.25"-18 thread. A105. square head. H54.75"-14 N. 6 pint capacity. C34. H48.T-223 SERIES MAIN CASE ITEM PART NAME 192 Plug-oil drain 193 Expansion Plug-shift shaft 194 Plug-oil drain 195 Plug-oil level 196 Oil Catcher-input 197 Plug-oil high level 197A Pipe-nipple oil level PART MODEL QTY NUMBER A97. H44 H33 - 41 . H40. H36. C20. C29. A94. H46.875" O. 0.62" square one end.05" thick. E23. 1 P-112 Male. H46. H36. 1 1 P-212 1199-J-894 - 1 1898-A-261 - 1 2296-W-1063 Female. C32.F. H47. C20. H39. 0.75"-14 thread. H57 H29. C20. C34. H46. 0. 0. C22. C30. H31. C34. 1. A104. C44. H55. A92. C29. 0. H31. not available at this time. 1 1898-X-856 0. H31. C30. H44. 1 1 PW-214 P-112 0. E22.. H55. H55. C22. H54. E23.. Magnetic-male square head.F. M4 A84. 0. H29. C30. A88. 1 1199-K-3287 Magnetic-0. C29. H56. A89. H40. H57 A89. H56.75"-14 P. C32. H29. C43. A91. H48. H52. A98. H41. disc shape. H41. C30. H41.38" diameter.75" standard pipe thread. H46. H47.D. H47. H56. cup shape. H39. A88. H44. H40. H48.P. C41. 5 pint capacity. A91.75"-14 thread.75"-14 N. 0. H47. A99. A92. H36. E22. H39.75"-14 thread. H33.08" thick. C32.F. A103. 0. H54. A98.71" other end. H33. C32. C44. square head. 1 P-112 Male.T.P. not available at this time. H41. 1 P-24 A105. P. No longer available. 0. 2. H55.75" standard pipe thread. 0. H56.75"-14 N. small fork tang.68" deep.15" long. H36. H48.25" wide. H47. not available at this time. H53.09" diameter double drill square head. H48. H40.D. single lip and dirt lip with spring. A105.75" standard pipe thread. A88. 0. 0. H56.82" I.19" deep. H47.75" O. 0. 45 degree elbow. H52.75"-14 N.75" shaft. H41.25" long. Male.00" long.50" one end. H53. H29. . 7. H57 All 1 A-1205-N-1132 201 Oil Seal-shift shaft All 1 A-1205-N-1132 202 Shift Fork-declutch M4 1 2849-G-241 All others 1 2849-L-220 203 Lockwire-shift fork 204 Lockscrew-shift fork All All 1 1 LW-166 26-X-54 205 Shift Shaft-declutch C20. H54. 0. C44..00" deep0. H31.D.F. 2849-T-332 forging.21". H33. small fork tang. H36. replaces A-1805-S-305 with single lip only. C43. C30. 2849-Z-338 forging.F. H55. 0. 0. 1.13" wide. replaces A-1805-S-305 with single lip only.. 1. left quadrant. 7.13" and 0. H39. Included in item 155. E23. C44.25" wide. 1. 2.75" shaft.T-223 SERIES MAIN CASE ITEM PART NAME 197B Elbow-high oil level MODEL - PART QTY NUMBER 1 1898-C-835 - 1 1898-S-201 H29. H56. H54.38"-24 thread. C32. 90 degrees. H44. 0.P.19" wide. single lip and dirt lip with spring.44"-20 UNF. 0. C34. 2 equal ball detents 0. H46. H52. C22.50" long. Same as T-410 except unequal ball detent. 0. H52. 0. H40.25" fork opening.. H44 C41. Use for 3 and 4 pint capacity. 0.69" other end.13" long and ball detent end setscrew hole bottom.T. A89..26" O. 2 43 1. H55. setscrew hole bottom right quadrant. H40.D. 0. Same as T-410 except 7.16" deep from ball detent end. C41. H57 C29. A104.D. 0.26" O. square head. depth 0. 16 gage. 1.75"-14 thread. C31. 6.25" long.T.05" O. H53 1 2843-T-410 1 2244-M-39 E22. H57 - 1 1898-X-258 1 1898-D-836 1 P-112 200 Oil Seal-shift shaft A84.25" fork opening. not available at this time. Same as T-410 except 2 equal ball detents 0. 1 2843-W-439 M4 1 2843-Q-459 All others 1 2843-C-393 198 Nipple 199 Plug-oil level DESCRIPTION 0.D.. tap drill 1. 0.. H41. 0. C43. 0. Same as B-392 except 2 unequal ball detents 0. C34. H54 H48. No longer available. H46 - 14 1229-K-1597 Same as K-453 except extra slot added at ball detent area.19" deep from ball detent end. H40.28" long. H36. H44. H53. C22.75" diameter hole. 6.38"-24 thread.. A105 C20. H29. H41. 0. H40. setscrew hole upper right quadrant. H39. C44.D. A98.41" I.hi-low 208 Lockwire-shift fork 209 Lockscrew-shift fork 210 Washer-case and top cover 211 Capscrew-case and top cover 212 Breather-oil Plug 213 Capscrew-case top cover PART MODEL QTY NUMBER A84. grade 8. 0. inner fork width 0.63" long. H46. H57 C22 1 2843-S-409 DESCRIPTION 7. C32. H43. C29.T-223 SERIES MAIN CASE ITEM PART NAME 206 Shift Shaft. 1 1 P-42 S-2610-2 Hex socket-female. H31. Same as B-392 except extra slot added at ball detent area. C30. 12 10 14 S-268-2 0.31" long.09" diameter double drill square head. H44. H29. H53. H47. H36. H57.15" long. 2849-Z-338 forg.41" long and 2 equal ball detents 0. H57 M4 All others C43. 0. M4 A99. H44. A104. H54. 1. 1 2297-P-2226 C31. H40. H52. C20.00" long. 1. E22. H55.38"-16. 7. A90.hi-low 207 Shift Fork. H55. C41. H52. A92. C41. H46.03" long. Same as U-281 except 0. H39. 0. H41.38" fork opening.09" thick. A92.D. 1. H53. A94. H33. H48. H33. H56 1 2843-K-453 1 2843-U-463 M4 1 2843-P-458 M4 1 2849-U-281 All others 1 2849-V-282 All All 1 1 LW-166 26-X-54 C43. Same as B-392 except 7. 0. Same as B-392 except 7. H56. H46.19" deep. A94. A103. H54. 45 . H47.25" long. H56. A89. A89. H56. H48.38"-16. 1.19" deep from ball detent end. setscrew hole upper left quadrant. H33. 0. C44. 16 gage.. H57 M4 All others A84. A91. H31. H52.. E23. H55. 12 10 1 A-1199-C-1043 0.23" deep. H31. 1 2843-B-392 A90.. E22. A105. H29.19".06". H41. E23 1 2843-X-440 H29. H54. H52. H39. A99. H47. A88.125"-27 thread. inner fork width 0.13"-27 N. C43. 2 equal ball detents. C43. H55. A91.16" and 0.T.75" O. grade 8. A103. 2 equal ball detents 0.P. 2. H36.F. A88. 0.00" long. A104. H53. H41. 2 dowel holes 0. C41. H39. Not used on 223 models in this book. H56. H57 M4 PART QTY NUMBER 2 1846-X-284 DESCRIPTION 0.40". A104.44" diameter ball. C44.39" diameter and 2 holes 0. H48. A90.93" thru hole thru 2 lower bosses for interlock. same as N-196 except with 0. E23. A98. available as assembly only. C41. H36. C41.40" and 2 dowel holes 0. 0. 13 coils. A98. H54. H56. 10 thru holes. H31. 1. 1. H48. 1. same as J-270 except add 0. C43. 3855-C-445 rough part. H56 H29. H41. H46. H29. A94. 3855-E-447 rough part. 1 1 1 2858-B-236 1898-E-57 2858-A-1 9.48" free length. 47 3855-C-445 rough part. H47.75 coils. with interlock. 3855-C-445 rough part. C32. 1 A-3855-N-196 1 3855-J-270 1 3855-S-279 1 3855-L-272 * All preformed gaskets are replaced with silicone liquid gasket at time of service.25 coils. C30. C30. 1. Not used on 223 models in this book. C22.38". 1 2858-C-237 10. 1 2858-C-237 10. H46 H40. H33. A99. A104.38" diameter. H36. Includes item 215. 3855-B-444 rough part. H48. Not used on 223 models in this book. H36. A89. 0. H44.75" long. E22. H29. M4 All others A84. H39. C20. Includes item 215. Not used on 223 models in this book.. A92. A103. C31. E23 C34. 1. H53. 1 breather hole. 8 mounting holes 0. A99. 0. C29. 13 coils.88" free length.44" diameter ball. H43. H54.36" diameter. A104. .75 coils. C31.28" free length.T-223 SERIES MAIN CASE ITEM PART NAME 214 Dowel-T-case and cover 215 Pin-brake bell crank 216 Ball-shift shaft lock 217 Spring-shift shaft lock 218 Ball-shift lock 219 Spring-shift shaft lock 220 221 222 223 224 225 226 227 228 229 Pull Rod-brake Washer-brake pull rod Washer-brake pull rod Bellcrank-brake operating Cotter-bellcrank pin Washer-bellcrank pin Cotter-brake pull rod Cotter-brake pull rod Gasket-cover Cover Assy. C34. A105.16" diameter hole. H52.41" and 2 dowel holes 0. A105. C44.88" free length. 1 1 1898-E-57 2858-A-1 0. E22 A88. Not used on 223 models in this book. Not used on 223 models in this book. E23 C34. A89.25 coils. E22. M4 All others All A99. C31. Not used on 223 models in this book. E23 C22. H54. A104. H48 All A99. H31. H44. H33.75" diameter. 12 thru-holes. A91.* 3855-E-447 rough part. 1 1846-B-262 1. A92. Silicone gasket-use as required. H46. C20. 0. C32. 2 dowel holes. H41. H33. A94. 1 1 1 1 1 1 1 1 1 1 1 2858-B-236 1845-A-27 WA-36 WA-36 302-T-540 K-248 WA-310 K-236 K-236 2297-Z-6656 3855-B-210 1 A-3855-G-189 9.48" free length.75" hole. H55.28" free length. H31. 8 mounting holes 0. C34. A90. 1.88" long.T-case top MODEL All A88. C32. Not used on 223 models in this book. H39. H44. C22. C32.38" diameter. H53.T-223 SERIES MAIN CASE ITEM PART NAME 230 Shaft-shift interlock pin MODEL C20. C30. C41. C31. H40. H57 PART QTY NUMBER 1 1846-D-264 49 DESCRIPTION 0. C44.62" long. C34. H55. H48. H47. C29. H56. . H52. 6. 13" bolt circle. C22.* 4 holes on 4. 17 coils. A105. H41. E23. H41. H41. 1 2847-S-617 A92. 0. 0. C34. A98. H41. C41. 4 2258-Q-719 A90. A89. C20. C22. A104. H41.09" thick. 0.D. A98. A89. 1 A1-3736-U-229 A90. C34 1 2258-T-1268 * All preformed gaskets are replaced with silicone liquid gasket at time of service. C22. loctite patch. A94. A99. C20. A105. C41. C34. A94. A90.. 0.D. A89. H44 A88. 176 Washer-brake mounting capscrew 177 Capscrew-brake mounting 178 Lever-brake 179 Roller-brake 180 Spring-brake shoe return PART MODEL QTY NUMBER A88..D. A99. 1 2247-K-1259 A90. A90. use as required. C32. C22. A105. C22.81" O. C20. grade 8. C22. C20. C41. .42". H41. H44 A88. A89. 1 2297-L-6720 A92. A89.. Center hole diameter of 4. A90.D. A104. C22.T-223 SERIES DLM BRAKES ITEM PART NAME 172 Gasket-brake oil deflector 173 Oil Deflector-brake 174 Washer-brake oil deflector 175 Backing Plate Assy.. C41. A90. A99. E23. 1. H44 A88. 5. . A94. C22.50" I.56" I.D.00". 0. E23. H41. E23. H41. 0.D. C34. 4 flats. A94. C41.. E23. 1. A105.31" bolt circle. H44 A88. 32 DESCRIPTION Silicone gasket.2297-Z-6656 A90. A89. A104.00" long. E23. A104.00" O. 1 1829-Z-754 A92. A105.. A89. A104.H44 A88. 1 S-278A-2 A92. 10.43" O. E23. C20. 2 notches.31" bolt circle.D. C20. A89.50" O. 10. A99. H44 A88. A105. 0. H41.20" O. H44 A88. C20.D. C41. 0. A89. 0. 1. 0. A92. A99. C32. C34. 0.09" thick with 2 holes on 4.09" free length. A92. H44 A88.00" O. E23.D. C32. C32. A98.88" solid height.. C22. A98. A98.D. C20. C32. H44 A94.. C41. A105. A105.. A92.47" diameter4 holes on 4. C41.56" I. C34. 3. A104. A92.88" free length. A104.47" I.25" thick.44"-14. 1 1229-E-1513 A92. E23. 2. C20. 3. A94. Tension spring. A104. A90. length from center of linkage hole to center of roller hole approx. C41. H41. C22.D. C41. A105. H44. E23. A92. C32. . 0. A92. C41. C22. A104. C20. H44. 0. A89. 0. A89. H41. A92. A105. H56 A88.75" long. C20.63" pilot diameter. A99. E23.50" bolt circle. A105. A105. A92. C41. 1 LW-1616 A90. H41. H44 A88. 4 1229-E-1513 A92. Replaces A4-3722-L-194. C41.D. C22. A104. C41..81" O. C20. C20. A89. E23. 16 gage. 1 3719-Y-51 A90. H41. A89. 3. C20. Brake linings and rivets. A105. A104.T-223 SERIES DLM BRAKES ITEM PART NAME 181 Brake Shoe and Lining Assy. 1 hole drilled in head. A104. A104. E23. 0. H41. 2 A6-3722-L-194 A90. C20.45" punch-4 holes on 4. C34. H56 34 DESCRIPTION Includes item 182 and 183. 182 Rivet-lining to shoe 183 Lining Kit-brake shoe 184 Drum-brake 185 Washer-brake drum capscrew 186 Lockwire-brake drum capscrew 187 Capscrew-brake drum PART MODEL QTY NUMBER A88. Included in item 181. H44 A88. E23. H41. Included in item 181 and 183. A89. A104. E23. C22. A92. A105. A89. C22.00" long. grade 8. A89.. A94. H44 A88. 20 RV-354 A90. A90. H44 A88. 4 S-276D-2 A90. A105. 0. A104.47" I. 1 2000-S-1397 A90. E23. C22. C22. H41. 0. 16.09" thick. C41. A92. H44 A88.44"-14. grade 8. Includes lining and rivets.50" from center line outer hole to 1. 9. H52 1 4 A-3787-Q-17 2758-A-53 2710-X-1154 forging.75" long. H36. H36.. H52 H29.75" bolt circle diameter. 0. H36. H36.D. H52. H36. H36.01" across flats.59" I. 235 Capscrew-brake mounting 236 Camshaft H29. 2.56"-12. H36. 16. 4. H52 H29.13" long with loctite patch. H52 1 3897-R-3008 1 4 A-3819-E-525 S-166D-2 H29.56" O.T-223 SERIES DCM BRAKES ITEM PART NAME 231 Nut-lock 232 Washer-brake 233 Lever-brake MODEL H29.D.75" long. H36. 0. 243 Hub-brake H29. 0. 0.00" bore.00" long. 0.34" long.40" long.D. H52 1 4 A-3736-D-472 S-289A-2 H29. 6. H36. H53 H29. 11 coils. 1 long drilled in head. H36. H52 H29. H52 1 2710-U-151 237 Strut Assy. 5.38"-24. H29. 238 Spring-brake shoe return 239 Brake Shoe and Lining Assy. H52 24 RV-875 1 2000-J-1362 1 A2-3722-G-501 H29. H29.09" thick. H52 1 A2-3722-G-501 Includes lining and rivets. 16 gage.25" from center line outer hole to 1.20" bolt circle. 1. 240 Rivet-lining to shoe 241 Lining Kit-brake shoe 242 Brake Shoe and Lining Assy. 1. 0.36"-24 UNF. 0.50"-13. H36 1 372-B-210 234 Backing Plate Assy.56" thick.50" diameter-4 holes on 5.. H36. 1. H52 H29. 0. Mounted on item 243 using item 186.00" bore. H52 PART QTY NUMBER 1 1779-Z-260 1 WA-39 1 372-X-206 DESCRIPTION 0. 32 serrations equally spaced.. H36. H52 H29. H52 1 LW-1616 244 Drum-brake 245 Capscrew-brake drum 246 Lockwire-brake drum capscrew 36 Includes brake shoe lining and rivets. . H36. H36. 4 holes on 5.75" diameter. 6. H52 H29. H36. 0. H52 H29.188" O. D.D. 0. 0. 35 DESCRIPTION 0. 2. 0.003"..32" I. 2.00" long. with shift groove.38"-16. grade 8. Not used on 221 models in this book.44" O.09" thick. . 0.12" thick. 0.38"-16.09" thick.. 1.. Not used on 221 models in this book. 82 83 Plug-input shaft front brg.67" O. 1. 4 holes and 8 grooves.796-1) All All Gear-low speed sliding (1. 1. 0. M7 1 1 1 1 1 3 2 3 2 1 357 353 1229-F-3048 2803-S-1865 2803-T-1866 2803-U-1867 2803-D-2162 2803-E-2163 2803-F-2164 A3-3866-U-749 1 1 3 3 3 A-3866-U-1113 P-42 1229-K-1597 WA-16 S-2612-2 3 S-268-2 74 Gear Assy. Replaces A-3866-U-749 with oil seal A-1805-N-378 which replaced A1-3866-U-749 with oil seal A-1805-W-413. 0.D.D. included in item 74.75" O. cap Washer-input shaft front brg.. Not used on 221 models in this book.12" thick. 20T. 3866-J-1258 cast. Not used on 221 models in this book. no longer available. use as required. 0. 0. M7 All others All 1 1 1 1 3880-P-744 3880-J-1128 1844-C-809 1828-L-142 A1. .25" bolt circle. M.D. Replaces S-2611-1 which is 1. 3 holes . includes item 73.* Ball bearing. 0. Not used on 221 models in this book. cap Capscrew-input shaft front brg. 8.T-221 SERIES MAIN CASE ITEM PART NAME 67 Capscrew-input shaft rear bearing cage 68 Washer-input shaft rear brg. 9 holes. 20T spline. 19T. 9 holes. spur.41" I.18" I. includes item 86.005".83" O.005".D. use as required. 0.-input shaft front brg.51" O. M7 All others A1 All others A1. . 1.75" bolt circle. 2. M6. 1..38" I. Sold with direct drive gear only.D. M6. .39" I.. 0. 0.-direct drive (1.38"-16. 33T.49" bushing bore. 1.09" long with threaded end..D. 84 A1. 19T spline. grade 8.125"-27 thread. open end.D. 3 holes on 3... 9. 3 holes.00" O. 4.796-1) All 1 A-3892-U-1711 1 A-3892-X-1714 1 1 1829-Y-727 3892-V-1712 1 3892-Y-1715 A1.. 3 holes.94-1) 75 76 Washer-direct drive gear Gear-low speed sliding (1. split.. cap All others 81 Cap Assy. 3. use as required. 4. 0. 0.. no threads.D.68" O. closed end. 1. 1. Not sold separately. 1.14" long. 1. No longer available. .20" I..67" long.-direct drive (1. 1. M. Bushing-direct drive gear All All 1 1 1 1 332 339 1829-X-726 1825-W-205 Gear Assy.38" long.D.09" thick....41" I. 0.D. 0.D. 4 holes on 4. spur.50" O.28" wide.98" O. spur. Ball bearing with shield. MODEL All PART QTY NUMBER 4 S-268-2 A1 All others All 4 4 1 1229-K-1597 WA-16 3866-R-746 70 71 Gasket-input shaft rear cap Bearing-input shaft rear All All 1 2297-Z-6656 1828-P-94 71A 71B 72 73 Cup-input shaft rear Cone-input shaft rear Washer-input shaft rear brg. Silicone gasket.D. M6. 1. 1.003".63"-10 spline. 9 holes.D. Hex socket-female. 3. 1. Shipping cover only. 0.. grade 8. Not used on 221 models in this book. use as required. M. 1. use as required.09" thick.010".010". use as required.94-1) 77 Shaft-input 78 79 Spacer-input shaft Bearing-input shaft front 79A 79B 79C 80 Cone-input shaft front Cup-input shaft front Washer-input shaft front Shim-input shaft front brg.49" bushing bore. M6.36" I.00" O. 33T..D. 2.41" I. cage 69 Cage-input shaft rear brg..31" long.75" O.D. use as required.D.. includes item 73.63"-10 spline.67" O. .D. with shield. M7 All others * All preformed gaskets are replaced with silicone liquid gasket at time of service..D.. 0. spur.50" long.63" wide.00" long. M.D.98" O.D. 0.78" O.D.. 1.69" long. A1-3897-A-1431 1310 series.39" I.D.D. 0. 1. 0. M.67" O.H.D. 4T.25" thick. 110 Cone-rear output shaft rear brg.D. 0..D.. grade 8.50" wide. M6. external teeth.50" O. M6. 2847-P-640 Included in item 92.00" long. 1.53" long. 1.H. 0. 0. 1. 0.. 0. 37 1. 0. M7 1 1 1 2 1 1 2 1 1 3 1 3 1 1 1 1 1 1 A-1850-R-18 K-2412 K-2410 S-268-2 S-2614-2 10-X-665 S-269-1 S-2614-2 10-X-665 1229-K-1597 1229-E-525 WA-16 1229-E-525 A-1199-C-1043 2297-Z-6656 1898-Q-849 1898-P-848 109 Cup-rear output shaft rear brg. 1829-V-100 Not used on 221 models in this book. M7 1 M.. 2. Part no longer available.H.D.D.00" height. 1.25"-10T spline. M7 A1. external teeth. threaded one end. N4.. 1. Helical.D. 5. 111 Gear-rear output shaft All All All 1 1 1 15245 15126 3892-R-1708 112 Shaft-rear output All 1 3880-Q-745 98 Bushing-speedometer driven gear 99 Gear-speedometer driven 100 Sleeve-speedometer driven gear 101 Plug-speedometer hole 102 Cotter-rear output shaft nut 103 Capscrew-rear output cap N4.88"-18 NS 2A threads other end. N4. N7 All All 97 Cap Assy. 0. grade 8.D.. 1. M7 All A1 All others N. 1. N7 PART QTY NUMBER 1 PW-226 A1 1 A1. 1..00" long.50" long. helical. A1-3897-Q-1655 1310 series. includes item 93. 0.25" long.08" thick.D.00" long. 15T.63" diameter. M.13" diameter. A1-3897-A-1431 1310 series.. 9.D.D. 0.D. Not used on 221 models in this book. 0.38"-16. Flanged. Helical. M6.25"-10T spline. 0. flat head.D.. 2847-P-640 Hook shape (cross section). Silicone gasket. 1. M7 All others A1. included in item 91.75" long.13" diameter.31" O..D. 1. and case.69" long. 1. 0..13" O. includes item 93.D. includes item 96 and 98..H.88" O.75" long. 3.63"-10T spline.06" long. M. grade 8.* 4T.75" I.25"-10 spline. flat head. 3. 1. 0. M6. includes item 90. 1.. M6.88" bolt circle..63"-10T spline. M6. 0. 0. 0.75" O.81" O. 0. slotted.77" wide. 1.D. M6. R.. 1.75" O. N7 1 1 DESCRIPTION 1. 0.38" wide.50" long. M6 1 M7.39" I.13" diameter. 0.25" bore. 0. . 1. 1.78" O. 1.38"-16. 0.03" I. M7 M. 0.38"-16.26" long. 0.38" thru-hole. 0. 2. Not used on 221 models in this book.81"-20 UNEF 2A threads one end. 1. 2.38"-16.D.09" thick.T-221 SERIES MAIN CASE ITEM PART NAME 85 Plug-input shaft shipping cover 86 87 88 89 90 Oil Seal-input shaft front brg. included in item 81. 0.88"-14..D. M7. grade 8. A-1805-E-447 2.34" wide.. Not used on 221 models in this book.D. 0. N7 104 Washer-rear output cap A1 All others 105 Breather-rear output shaft cap 106 Gasket-rear output cap 107 Gear-speed driven 108 Spacer-rear output shaft * All preformed gaskets are replaced with silicone liquid gasket at time of service.44" O. Helical.25"-10 spline.12"long. R. 1. R.D. included in item 97. 1. 33T.78" O.39" I. cap Washer-input shaft Nut-input shaft Cotter-input shaft nut Deflector-input yoke 91 Flange/Yoke-input 92 Flange/Yoke-rear output MODEL N4...25" I. 1.74" O. 0. 0. use as required.D.81" I. 2.D. 4 holes on 3.76" I. M7 1 1 1 1 M. double seal lip and case.38"-16.41" I. K-2412 0.-rear output shaft All 1 A-3866-Y-805 All 1 1199-M-1105 A1 A1 1 1 1898-N-846 1898-U-671 A1... No longer available..44" flange O. 1.09" thick.97" O.77" wide.D. double seal lip. 0.03" flange width.. 1827-H-242 0.50" O.. 1 1 1 1827-H-242 1229-E-1331 A-1805-E-447 93 Deflector-rear output yoke 94 95 96 Nut-rear output shaft Washer-rear output shaft nut Oil Seal-rear output shaft M. L. M. M6.D. 3.38"-16. 4.75" I. 2. 6. brg. N7 - 3 3 3 1 1 1 1 1 1 1229-K-1597 WA-16 S-267-2 K-2412 1827-H-242 N-512-1 1229-V-1556 10-X-830 1229-K-1597 ITEM PART NAME 113 Cone-rear output shaft fwd. 3 holes. 2.38"-16".D. use as required.63"-10T spline. 3 holes. .H.010". 0. spur..D.005".13" diameter.75" O. M M6.D. Not used on 221 models in this book. .D. slotted.44" O.38" long. use as required. 0. 0. 0. washer 135 Shim-idler shaft front brg. .010". washer 134 Lockwire-idler shaft brg. 34T. 1..39" I. M6.D. M7 All others 116 Cap-rear output forward cap 117 Washer-rear output forward cap 118 Capscrew-rear output fwd. 0.88" long. Cone-idler shaft rear brg. 3 holes. Helical. Not used on 221 models in this book.94-1) 129 Shaft-idler All All All 1 1 1 1 1844-D-498 3892-W-1713 3892-Z-1716 3880-N-742 130 131 132 133 All All - 1 1 1 1 02476 02420 1829-H-788 10-X-1292 A1. Not used on 221 models in this book.39" I.003". 0. 6. 0. 0.39" I. use as required. 0. 4 holes.D.44" O. use as required. use as required. cap 119 Capscrew-idler shaft rear cap 120 Washer-idler shaft rear cap 121 Cap-idler shaft rear 122 123 124 125 126 Gasket-idler shaft rear cap Snap Ring-idler shaft Cup-idler shaft rear brg. use as required.D.005".. cap All others 136 Cap-idler shaft front brg.. 1.75" O. Not used on 221 models in this book.D.D. spur.796-1) Gear-low speed (1.25" bolt circle. .010".. Washer-idler shaft brg. grade 8.D. closed end. 39 DESCRIPTION 1.. 0.. 0.T-221 SERIES MAIN CASE All QTY 1 1 1 1 3 2 3 2 2 3 2 1 PART NUMBER 15126 15245 2803-V-1868 2803-W-1869 2803-X-1870 2803-V-1868 2803-W-1869 2803-X-1870 2803-G-2165 2803-H-2166 2803-J-2168 3866-T-748 A1 All others All All A1 All others All 3 3 3 3 3 3 1 1229-K-1597 WA-16 S-267-2 S-267-2 1229-K-1597 WA-16 3866-T-748 All All All All 1 1 1 1 2297-Z-6656 1854-E-187 15245 15126 3892-W-1713 127 Spacer-idler shaft gear 128 Gear-low speed (1.005". 1. slotted. 5. 38T. 0.09" thick. 0. use as required. M7 All others N4.41" I. 3 holes on 3.69" O. 3 holes. 138 Capscrew-idler shaft front brg. M.75" O. use as required. 0.75"-16.. 137 Washer-idler shaft front brg. 3 holes. brg. use as required. 0. 0.D. 3 holes. use as required.25" bearing diameter both ends.16" wide. 139 Cotter-output shaft nut 140 Nut-output shaft 141 Washer-output shaft 142 Capscrew-oil catcher 143 Washer-front brg..50" long.61" O..D. Stamping. 0. .D. Stamping..88"-14. use as required.78" I.69" I..* Not used on 221 models in this book. . use as required.D. 0. 2. Stamping. Cup-idler shaft front brg. use as required. use as required.63"-10T spline.09" thick.003".D. cap * All preformed gaskets are replaced with silicone liquid gasket at time of service. 37T.D. closed end. 115 Shim-rear output forward brg. 2. 0. . . .67" O. 0.09" thick.09" thick. 0.38"-16. use as required. grade 8. . 3 holes. 3 holes. 3 holes. 1.88" long. 0.63"-10T spline. 0. 0. 0. Capscrew-idler shaft brg.D. Gear-idler shaft Cone idler shaft front brg. 5. 114 Cup-rear output shaft fwd.. 1.. 1.41" I.44" bore.50" high. 0. 4 holes. 0. closed end.D.003".005". R.D.25" bore.003".13" O.25" bolt circle.25" bolt circle. 1. .67" O. Silicone gasket.12" O.09" thick.010"..63"-10T spline.. 1. .D. cap MODEL All All A1.. 0.D. 3 holes on 3. M All 1 1 1 3 2 3 2 1 LW-163 2803-V-1868 2803-W-1869 2803-X-1870 2803-V-1868 2803-W-1869 2803-X-1870 3866-T-748 A1 All others All All A1. 3 holes. 3 holes on 3.003".38" O. 0. Not used on 221 models in this book. 1.005".12" thick.. grade 8. . 3 holes. .25" bore.25" bore. .. grade 8. 3 holes. 1.09" thick. 4 holes.38"-16".88" long. use as required. 1..41" I.67" O. 0.010". . 1 A3-3866-U-749 3 holes on 3. grade 8.25" bolt circle. included in item 149.83" O.75" wide. 3. M6. N4.67" O. 1. 4 S-269-1 0. 2. Part no longer available.. N7 All others PART QTY NUMBER DESCRIPTION 1 A1-3897-A-1431 1310 series. M6 M7 All others 156 Snap Ring-front output shaft N4. and case.38" bore.25"-10T spline. 3..38"-16.77" wide.D..41" I. double seal lip and case..70" diameter. double seal lip. cap 147 Washer-front brg. 3 1229-K-1597 0..D. 1 3892-T-1710 19T. grade 8. includes item 160 (A-1205-Z-1768). 0. 4.D. 1 3866-X-752 3866-E-317 cast..50" wide. 3. 1 A-3897-C-2811 1310 yoke.78" I. 1 K-236 Not used on 221 models in this book. 4 threaded holes on 3. 0. grade 8. Replaces S-2611-1 which is 1. 0.75" O. 1 3880-R-746 9.75" diameter. 2.H.D.41" I. included in item 144. 3.D. 4 holes on 4.. with snap ring. 1 WA-36 Not used on 221 models in this book.D. 0.D. open end. 4 1229-K-1597 0.. 0.69" long.09" thick..77" I. spur..2297-Z-6656 Silicone gasket.38" long.50" O. * All preformed gaskets are replaced with silicone liquid gasket at time of service. 1.76" I. 41 .D. 0.09" thick. 0..75"-16. with snap ring.D. 1 A-1805-E-447 2. 1...D.* 1 A1-3866-S-747 3866-H-1256 cast. No longer avail. Part no longer available. included in item 144.25" bolt circle.77" wide. No longer available. M7 N4 N7 145 Deflector-front output yoke M. cap 148 Oil Seal-output shaft front All A1 All others All 149 Cap Assy.34" from threaded end to 1..D... M6. 0. 1 2847-Q-849 Not used on 221 models in this book. N7 All A1 All others 164 Washer-front output shaft rear cap 165 Capscrew-front output shaft rear cap A1 All others A1.12" long.50" wide.38" wide.67" O. includes item 145 (2847-P-640). 1.88" O. 1.. 1 1854-P-146 Fits over 1.-front output shaft rear N4.50" long.97" O. includes item 148.-output shaft front All 150 Gasket-output shaft front cap 151 Bearing-output shaft front All All 152 153 154 155 Oil Catcher-output shaft Washer-oil catcher Pin-oil catcher Shaft-front output A1. L.57" O. Helical. 3 S-2612-2 0.77" O.D.D. 1 1828-F-110 Ball bearing. 0.T-221 SERIES MAIN CASE ITEM PART NAME 144 Flange/Yoke-front output MODEL M.. 0. 1. internal brake mounting. N7 157 Clutch-front output sliding All 158 Gear-front output shaft All 159 Bearing-front output shaft rear All 160 Oil Seal-front output shaft rear A1 M. includes item 145 (2847-K-791).50" long.75" O. M7 N4..39" I. 3. Part no longer available.69" long. 1. M6. . 3 WA-16 0. 1 A-3897-D-3072 Same as C-2811 except undercut versus radius on deflector seat.D. with spring.. 4 WA-16 0.. 0.D.75" O. 1. 4 S-268-2 0. M.. 2.. 2. 1.D. enclosed cap with 4 holes on 4. with shift groove.. 0. N7 146 Capscrew-front brg. 1.75" I.25"-10T spline.D.09" thick.. threaded end to 1.19" I. included in item 163.D.75" bolt circle.38" long. 1 3880-T-1112 9. 0.13" O. 1 2847-K-791 "S" shape (cross section). .75" bolt circle.63"-10T spline.D.D. Replaces A-3880-R-746 which has snap ring and groove.75" O.* 1 1228-V-308 Ball bearing.D.D..38"-16. 1. 1 3892-S-1709 33T. M7 161 Spacer-front output shaft 162 Gasket-front output rear cap 163 Cap Assy. 1 A-1805-E-447 2.D. 1.09" thick. 2. includes item 145 (2847-K-791). 1. on shaft with 16T spline.67" wide. 1 A-1205-Z-1768 2.38"-16. 1.D.00" long.81" I. 1 2847-P-640 Hook shape (cross section).35" O.2297-Z-6656 Silicone gasket.75" diameter shaft. 1.D.39" I.53" from 0. 0.D. use as required. use as required.75" I. 1 1844-G-501 2.50" O. with interlock.25" O. Part no longer available.D.D. N7 All All All All 1 2 1 1 1 1 1 1 1 1 1 1 1199-K-1493 9-X-16 PW-216 P-24 1850-X-76 P-112 P-112 1898-X-856 P-112 1898-X-258 P-112 A-1205-N-1132 All 1 A-1205-N-1132 All All All A1 All others A1 1 1 1 1 1 1 2849-E-239 LW-166 26-X-54 2843-A-417 2843-C-419 2843-Z-416 All others 1 2843-B-418 All All All A1 All others A1 All A1 1 1 1 10 9 9 1 1 1 1 2849-E-239 LW-166 26-X-54 1229-K-1597 WA-16 S-268-2 A-1199-C-1043 S-2610-2 1846-X-284 1846-E-265 All A1.08" thick. E.D.38"-16.T-221 SERIES MAIN CASE A1. Not used on 221 model in this book.00" long.38"-24. 13 coils..P. D.D. 6. Replaces A-1805-S-305 with single lip only..08" thick.66" long with 1 hole 0. No longer available. single lip and dirt lip.08" thick.09" thick.44" diameter ball. M6. Not used on 221 models in this book. 3875-A-443 rough part.13"-27 N. E and F mounting bosses.39" I.D. E. 0.F. Not used on 221 models in this book. M7 All others 1 1 1 1898-E-57 2858-A-1 2858-Q-277 189 190 191 192 193 194 195 196 197 198 199 200 Name Plate Screw-name plate Expansion Plug-shift shaft Plug-oil drain Expansion Plug-shift shaft Plug-oil drain Plug-oil level Oil Catcher-input Plug-oil high level Elbow-high oil level Plug-oil level Oil Seal-shift shaft 201 Oil Seal-shift shaft 202 203 204 205 Shift Fork-declutch Lockwire-shift fork Lockscrew-shift fork Shift Shaft-declutch 206 Shift Shaft-hi-low 207 208 209 210 Shift Fork-hi-low Lockwire-shift fork Lockscrew-shift fork Washer-case and top cover 211 212 213 214 215 Capscrew-case and top cover Breather-oil Capscrew-case top cover Dowel-T -case and cover Pin-brake bellcrank 216 Ball-shift shaft lock 217 Spring-shift shaft lock MODEL A1 PART QTY NUMBER 1 4-X-840 1 N-16-1 1 PW-221 ITEM PART NAME 166 Stud-rear output shaft 167 Nut-rear output shaft 168 Expansion Plug-front output shaft 169 Hub-brake 170 Snap Ring-brake hub * All preformed gaskets are replaced with silicone liquid gasket at time of service.. 0. 5.D.31" O. No longer available. 2. 16 gage. 2849-X-336 forging. 2849-X-336 forging. No longer available.03" shift fork opening.38"-24. 1. A. Setscrew hole 150 degrees left of vertical. 0.06" long.. Part no longer available.75" O. D.03" long. C.63" O. 1. 0.52" free length. 0.38"-16. 0. 2.09" thick. non-magnetic. No longer available.. and F mounting bosses. 0. Not used on 221 model in this book.00" O.67" O. 1. M7 1 1 3897-F-1332 1854-P-146 171 Expansion Plug-brake hub 188 Case-transfer A1 A1 1 1 PW-221 3875-B-444 M 1 3875-W-491 M6. Not used on 221 models in this book.88" long. 0. less interlock. B. 1. 0.16" diameter.. 43 DESCRIPTION Not used on 221 model in this book. 0. Not used on 221 models in this book. 5875-S-513 rough part. 16 gage. grade 8.D.75" I. 0. 1... single lip and dirt lip. M. Male. 1. square head. 5875-L-792 rough part.75"-14 thread. 1. 1.03" shift fork opening.. 0.25"-18 thread. 0.. 1. 0.63" assembled. Not used on 221 models in this book. 1. Not used on 221 models in this book. 1.D.31" O.16" long.44" diameter..00" long. 0. N7 1 3875-M-793 All N4. M6.25" long. 4. square head. M7 1 3875-L-558 N4. 1. grade 8. Set screw hole 30 degrees right of vertical.75" I. 0. 1. E.D. 0.T. Female. with interlock. M. square head.. 0.25" O.. with interlock. 6. square head.41" I.D. 0. 0. Male. 1.06" thick.09" thick. and F mounting bosses. and F mounting bosses. 1. 0.00" long.88" free length. Replaces A-1805-S-305 with single lip only. . 0.16" long. 5875-L-506 rough part.D.75"-14 thread.00" long. 0.D. D (modified). 0. Not used on 221 models in this book. 63" dia..40" diameter-4 holes on 3. 3719-F-58 2. N4. 0. 1779-P-94 0. 7. 372-D-134 372-K-89 stamping. with drilled hole. Not sold separately. 12 coils 2. 0.75" O.13" diameter. T-221 SERIES DLM BRAKES ITEM 172 173 174 175 PART NAME Gasket-brake oil deflector Oil Deflector-brake Washer-brake oil deflector Backing Plate Assy.06" thick. 0.63" length at 20 lb.. 2258-Q-719 Tension spring.10" thick.75" long.38" diameter. * All preformed gaskets are replaced with silicone liquid gasket at time of service.D.D.44" diameter. S-266-2 0. grade 8. 0. ream. 0.D. M7 1 2858-A-1 All others 1 2858-Q-277 ITEM PART NAME 218 Ball-shift shaft lock 219 Spring-shift shaft lock 220 221 222 223 224 225 226 227 228 229 Pull Rod-brake Washer-brake pull rod Washer-brake pull rod Bellcrank-brake operating Cotter-bellcrank pin Washer-bellcrank pin Cotter-brake pull rod Cotter-brake pull rod Gasket-cover Cover Assy.66" I.. 0. 0. capscrew Capscrew-brake mounting Lever-brake Roller-brake Spring-brake shoe return A1 A1 A1 A1 4 4 1 2 2 181 182 183 184 Brake Shoe and Lining Assy.10" thick. Part no longer available. 0. grade 8. 0.70" bolt circle..44" diameter. M7.50" pilot diameter. 0.40" I.38" diameter.D. 13 coils. 10" long. use as required. 1.52" free length.-T -case top 230 Shaft-shift interlock A1 A1 A1 A1 A1 A1 A1 A1 All A1 1 1 1 1 1 1 1 1 1 1845-A-27 WA-36 WA-36 302-T-540 K-248 WA-310 K-236 K-236 2297-Z-6656 A-3855-G-267 All others 1 3855-X-258 M. 6. 1. Silicone gasket.65" diameter shaft.10" diameter. 0.13" bolt circle. 0.25" thick. Rivet-lining to shoe Lining-brake shoe Drum-brake A1 A1 2 1 A1 A1 4 1 4 185 Washer-brake drum capscrew 186 Lockwire-brake drum capscrew 187 Capscrew-brake drum PART NUMBER 2297-Z-6656 2847-S-617 1829-Z-754 A-3736-R-200 DESCRIPTION Not used on 221 models in this book. M6. 0. Not used on 221 models in this book. bonded lining.38"-16.. 0. breather hole in center and 2 cast interlock bosses on underside. LW-1610 16 gage. 3855-L-506 cast. Not used on 221 models in this book.38" diameter4 holes on 3.D.50" DLM. 0.. 0.75" long.25" x 1.10" diameter.50" O. 0.. 0.16" long.81" O.81" O. 0. Part no longer available. M6. 0.D. 1.31" O. 1. 1229-E-1513 Not used on 221 models in this book. 1.* No cast bosses on underside.88" free length. Part no longer available. 1229-E-1513 Not used on 221 models in this book. M. 0. Not used on 221 models in this book.00" long.75" long.D. 0. N7 1 1846-H-268 DESCRIPTION 0. 0.T-221 SERIES MAIN CASE PART MODEL QTY NUMBER All 1 1898-E-57 A1.38"-16.75" long. 10-X-1254 0.40" I. load. A13-3722-T-202 Includes lining. MODEL A1 QTY 1 1 1 176 177 178 179 180 Washer-brake mtg.D.06" thick. 0.44" I.. 0. 45 .D.38" thick. 0.. 36 32. 22. 20. 38. 36 24 13 15 18. 32. 19. 35 18. 22 14 24 38 16 15 24 13. 35. 39 26. 14 36 13. 19. 39 13. 23. 19 15 35 36. 35. 39 17 38 13 18. 37. 39 41 PART NUMBER 1898-A-261 1898-P-848 1898-J-504 1898-K-531 1898-L-532 A-1898-W-595 1898-U-671 1898-V-776 1898-S-799 1898-C-835 1898-D-836 1898-N-846 1898-Q-849 1898-X-856 1898-H-866 1898-J-868 2000-J-1362 2000-S-1397 2244-M-39 2245-X-50 2247-K-1259 2258-Q-719 2258-T-1268 2296-W-1063 2297-S-695 2297-P-2226 2297-Z-6656 2297-L-6720 2710-U-151 2758-A-53 2803-V-568 2803-W-569 2803-X-570 2803-L-1832 2803-M-1833 2803-N-1834 2803-Z-1846 2803-A-1847 2803-B-1848 2803-S-1865 2803-T-1866 2803-U-1867 2803-V-1868 2803-W-1869 2803-X-1870 2803-B-1874 2803-C-1875 2803-D-1876 PAGE 27 36 14 14 14 14 19. 18. 38. 19 24 27 24 40 34 PART NUMBER A-1805-B-158 A-1805-N-352 A-1805-R-408 A-1805-E-447 A-1805-P-536 A-1805-A-573 1825-R-200 1825-W-205 1827-H-242 1828-V-74 1828-P-94 1828-F-110 1828-L-142 1829-V-100 1828-S-149 1829-J-244 1829-P-380 1829-M-585 1829-D-680 1829-S-721 1829-X-726 1829-Y-727 1829-Z-754 1829-H-788 1844-J-166 1844-L-480 1844-D-498 1844-G-501 1844-S-565 1844-C-809 1845-A-27 1846-V-126 1846-B-262 1846-D-264 1846-E-265 1846-H-268 1846-X-284 A-1850-R-18 1850-X-76 1850-T-150 1854-P-146 1854-E-187 1854-W-257 1874-A-105 1898-H-34 1898-C-55 1898-E-57 1898-S-201 1898-G-241 1898-Q-251 1898-X-258 PAGE 13 13 17. 39. 24. 33. 29. 35 30.NUMERICAL PARTS LISTING PART NUMBER 3-X-161 4-X-840 4-X-1521 9-X-16 10-X-665 10-X-830 10-X-1254 10-X-1292 16-X-40 26-X-54 26-X-56 302-T-540 372-D-134 372-X-206 372-B-210 1199-J-894 A-1199-C-1043 1199-M-1105 1199-N-1106 1199-K-1493 1199-K-3287 A-1205-N-1132 A-1205-T-1242 A-1205-Z-1768 1227-L-714 1227-C-939 1228-K-37 1228-A-183 1228-V-308 1228-R-408 1228-S-409 1228-B-1380 1229-E-421 1229-E-525 1229-E-1331 1229-E-1513 1229-V-1556 1229-K-1597 1229-E-1669 1229-F-2814 1229-E-3047 1229-F-3048 1229-C-4553 1244-Q-1629 1250-G-475 1254-M-91 1779-P-94 1779-Z-260 PAGE 13 25. 14. 40 28 14 14 28. 22 20. 29. 30. 15. 23 36. 37 20 21 37 38 20 16. 40 32 27 23 29 13. 20. 15. 40 14 30 31 39 40 30. 36 39 13. 36. 37 25 13 13 13 30. 19. 17 16 16. 17. 21. 37 23 35 38 35 18. 17. 36 19 26. 22 20. 36. 19 14 15 35 35 32. 39 19. 39 13 30. 37 40 22. 23. 39 14 14 34 33 28 19 32 32. 40 32 34 34 13 13 13 16 16 16 20. 22 35 35 35 37 37 37 16 16 16 . 36 19 20 28 28 36 36 27. 27 28. 27 38. 37. 39 21. 40 40 34 34 27 20. 40 37 14. 40 22. 38 24 17. 36. 39 19. 29. 37 13 28. 22. 25. 39 13 26. 14 16. 39 36 23. 38 38 17 25 21. 38 14 38 23. 38 14 14 24 13 28 39 28 29 29 30.NUMERICAL PARTS LISTING PART NUMBER 2803-G-1931 2803-H-1932 2803-J-1934 2803-D-2162 2803-E-2163 2803-F-2164 2803-G-2165 2803-H-2166 2803-J-2168 2843-C-107 2843-B-392 2843-C-393 2843-S-409 2843-T-410 2843-Z-416 2843-A-417 2843-B-418 2843-C-419 2843-W-439 2843-X-440 2843-K-453 2843-P-458 2843-Q-459 2843-U-463 2847-E-291 A2-2847-Q-303 2847-S-617 2847-P-640 A-2847-R-642 2847-K-791 2847-Q-849 2848-H-86 2848-J-88 2848-E-161 2849-Y-77 2849-L-220 2849-E-239 2849-G-241 2849-U-281 2849-V-282 2858-A-1 2858-T-20 2858-W-101 2858-X-102 2858-B-236 2858-C-237 2858-Q-277 3221-S-19 3260-H-1256 3266-Y-857 A1-3280-R-7896 PAGE 17 17 17 35 35 35 37 37 37 13 29 28 29 28 39 39 39 39 28 29 29 29 28 29 13 14 18. 23 36 18. 21. 38 18 18. 39 18. 22 25 19 35 38 37 35. 22 17 17 36 25 19 17 35 25 26 26 42 PART NUMBER 3875-B-444 3875-A-469 3875-W-491 3875-K-531 3875-L-558 3875-M-793 3875-Z-884 3880-X-336 3880-U-723 3880-N-742 3880-P-744 3880-Q-745 3880-R-746 3880-A-807 3880-T-1112 3880-J-1128 3891-C-1849 A-3892-J-1544 3892-P-1550 A-3892-R-1604 3892-T-1606 A-3892-W-1635 3892-Y-1637 3892-B-1640 3892-C-1641 3892-R-1708 3892-S-1709 3892-T-1710 A-3892-U-1711 3892-V-1712 3892-W-1713 A-3892-X-1714 3892-Y-1715 3892-Z-1716 3892-K-1805 A-3892-L-1806 3892-W-2441 3892-X-2442 3892-Y-2443 3892-Z-2444 3897-N-1002 3897-F-1332 3897-Q-1369 3897-R-1370 A1-3897-A-1431 3897-J-1440 3897-K-1441 A1-3897-Q-1655 3897-L-1728 3897-M-1729 A-3897-T-1762 PAGE 39 26 39 26 39 39 26 13 21 37 35 36 38 21 38 35 19 15 20 15 21 15 21 21 21 36 38 38 35 35 37 35 35 37 21 15 15 15 15 15 13 25. 39. 23 18 36. 32. 40 23 18 25 23 PART NUMBER 3280-S-7897 3290-Q-1005 3290-E-1071 3290-F-1072 3290-G-1073 3290-R-1084 3719-Y-51 3719-F-58 A6-3722-L-194 A13-3722-T-202 A2-3722-G-501 A-3736-R-200 A1-3736-U-229 A-3736-D-472 A-3787-Q-17 A-3819-E-525 3826-X-284 A-3826-Y-285 3838-N-196 A-3855-G-189 A-3855-N-196 3855-B-210 3855-X-258 A-3855-G-267 3855-J-270 3855-L-272 3855-S-279 A-3866-S-357 A-3866-S-721 A-3866-B-730 3866-C-731 A-3866-D-732 A-3866-E-733 3866-R-746 A1-3866-S-747 3866-T-748 A3-3866-U-749 3866-X-752 3866-C-757 A-3866-W-777 3866-N-794 A-3866-X-804 A1-3866-X-804 A-3866-Y-805 A-3866-C-887 A-3866-G-891 A-3866-Y-935 A-3866-U-1113 A-3866-R-1162 3875-V-438 3875-Q-433 PAGE 18 26 26 26 26 26 33 40 33 40 34 40 32 34 34 34 14 13 15 30 30 30 40 40 30 30 30 13 17 23 20. 36. 23 18 14 . 40 18. 40 13 14 14 30 30 39. 30. 38 33 32 34 25. 16 11. 39 35. 40 36 13. 37 11 11 12 12 6 6 6 7 8 9 9 9 40 33. 39 14. 38. 35. 37 28. 29. 35 16. 36. 22. 39 37 23 13 27. 27 39 39 25 17. 16 10. 38. 23 18 22 21 24. 29. 38. 36. 40 13 34 30. 17. 35 13 15. 35 16 16 37 37 36. 14 40 14. 23. 16 10. 34 38 13. 18. 37 36. 37 20 20 20 20 21. 36. 34 PART NUMBER LW-163 LW-166 MPS 3831 MPS 4118 MPS 4120 MPS 4121 MPS 4122 MPS 4123 MPS 4124 MPS 4126 MPS 4217 N-16-1 N-512-1 NL-26-1 NL-28-1 P-24 P-42 P-112 P-212 PW-210 PW-214 PW-216 PW-221 PW-225 PW-226 PW-252 RV-354 RV-875 S-166D-2 S-256P-2 S-266-2 S-267-2 S-268-2 PAGE 22. 37. 13 11. 28. 23 18. 16 10. 35 16. 29. 20 10. 39 10. 24 10. 19.NUMERICAL PARTS LISTING PART NUMBER 3897-Y-1793 3897-Z-1794 3897-K-1961 3897-L-1962 3897-P-1966 A-3897-C-2811 3897-R-3008 A-3897-D-3072 332 335 339 353 357 372 376 02420 02476 15126 15245 25520 25584 25821 25878 31521 31597 155NYS24-6 2WCS24-43 2WCS24-81 2WCS28-32 HM-89411 HM-89449 K-236 K-238 K-248 K-2410 K-2412 KIT T-221-1 KIT T-221-3 KIT T-221-4 KIT T-221-5 KIT T-223-1 KIT T-223-2 KIT T-223-3 KIT T-223-4 KIT T-223-5 KIT T-223-6 KIT T-223-7 KIT T-223-8 LW-1610 LW-1616 PAGE 18 18. 37 14. 15. 30. 29. 25. 39 23. 19. 23 18 18 18 38 25. 38 36 35. 24 25. 35 27. 40 S-269-1 S-276D-2 S-278A-2 S-289A-2 S-2610-2 S-2612-2 S-2614-2 WA-16 WA-36 WA-38 WA-39 WA-310 43 PART NUMBER PAGE . 39 27 14 26. 36. 38. 40 13 30. 20. 36 26 33 34 34 13. 22. 15 10. 39 17. 15. 22 21 23 18. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS. we will. © 1990 Meritor Automotive. EXPRESS. abuse or improper installation. buyer agrees not to make any deduction on account thereof from remittances on current accounts while claims are in the process of disposition. If it is necessary to return any parts under this warranty. Inc. or take back the nonconforming parts and refund the monies paid by buyer for such parts. Any expense incurred without our consent for repairs or replacement will not be allowed. at our option.S. As the exclusive remedy under this warranty. R I G H T F R O M T H E S T A R T. INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. reserves the right to revise the information presented or discontinue the production of parts at any time. repair or replace such parts free of charge. M E R I T O R Worldwide Aftermarket Meritor Heavy Vehicle Systems.meritorauto. LLC 7975 Dixie Highway Florence. Information contained in this publication was in effect at the time the publication was approved for printing and is subject to change without notice or liability. PB-90202 Revised 12-97 /05060 . IN NO EVENT SHALL SELLER BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.com P A R T S. All Rights Reserved Printed in the U. IMPLIED OR STATUTORY. Inc. Only genuine Meritor replacement parts are covered by this aftermarket parts warranty. maintenance or repair) when such parts are used on vehicles the specifications of which have been approved by our Engineering Department. Meritor Automotive.MERITOR AFTERMARKET PARTS WARRANTY We warrant all new parts for one year from date of shipment to the buyer against defective material or workmanship (but not against damage caused by accident. if found on examination by us to be nonconforming and if any necessary return charges are prepaid.A. KY 41042 USA 888-725-9355 http://www.