RF-5800M HH Ops Manual

RPUBLICATION NUMBER: 10515-0234-4200 JULY 2007 Rev. C RF-5800M-HH EXPORT MULTIBAND HANDHELD RADIO OPERATION MANUAL The material contained herein is subject to U.S. export approval. No export or re-export is permitted without written approval from the U.S. Government. ATTENTION The default Security Level 3 password for this radio is: 2445830 This password can be modified by a Security Level 3 user. Zeroizing the radio will reset the password to that shown above (2445830). For more information on security levels and passwords, refer to Paragraph 4.4. CUT HERE .This page intentionally left blank. Copyright © 2007 By Harris Corporation All Rights Reserved FIRMWARE RELEASE: V6. No export or re-export is permitted without written approval from the U.harris. Government. New York 14610-1887 USA Tel: 585-244-5830.S. export approval. C RF-5800M-HH EXPORT HANDHELD RADIO OPERATION MANUAL The material contained herein is subject to U.5 R HARRIS CORPORATION RF COMMUNICATIONS DIVISION 1680 University Avenue Rochester.com . Fax: 585-242-4755.PUBLICATION NUMBER: 10515-0234-4200 JULY 2007 Rev. http://www.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . COMPATIBILITY . . . . . . . . . . . .2 1. Audio Connections . . . . . . .3 2. . . . . . . . . . . . . .6 1. . . . . . . . . . . .TABLE OF CONTENTS Paragraph Page CHAPTER 1 – EQUIPMENT DESCRIPTION 1. Antenna Connections .1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQUIPMENT TEARDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1. SPECIFICATIONS . . . . . . .1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COMPATIBLE CABLES AND CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BATTERY INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . .7 1. . . . . . . . . . .4 2. . . . . . . . . . . . . . . . . . . . . . . . . VOICE/DATA COMPATIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FEATURES . . . . . . . . GPS Connections. . . . . . . . . . . . . . . . . . . . . . . .2 2. . . . . . . Data Cable Connections . . .2 2. . . . . . . . . . . . . . . EQUIPMENT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .3 1.1 2. . . . . . . . . . . . . . . 2-1 2-5 2-6 2-6 2-8 2-8 2-8 2-8 2-9 2-10 i . . . .2. . . . . . . . . . . . . . . . .1 2. . . . . . . . . . . . . . Optional Items . . . . . . . . . . . . . . . . . . . .5 2. . . . . . . . . . . . . . . . . . . . . . . . . . Battery Safety. . . . . . . . . .2.4 ITEMS INCLUDED WITH THE RF-5800M-HH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONFIGURATIONS. . . .2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2. . . . . . . . . . . .8 1. . . . . . . . . . . EQUIPMENT SETUP . . . . . . . . . . . . . . . . . . . . . .5 1. . . . . . .2. . . . . . . . PURPOSE OF THIS MANUAL. .2. . . . . . . 1-1 1-2 1-2 1-4 1-5 1-6 1-7 1-8 1-9 CHAPTER 2 – SETUP AND TEARDOWN 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .5. . . . . . . . . . . . . . . . . 3-1 3-1 3-2 3-8 3-9 3-9 3-9 3-10 3-10 3-10 3-11 3-11 3-12 3-12 3-14 3-15 3-15 3-16 3-17 3-18 3-18 3-18 . OPERATION TASK SUMMARY. . . .3. . . . . . . . . . . . .4 3. .6 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Test . .5 3. . . . . . . . . . . . . . . . . . . . . . . . . . . .5. . . . . . . . . . . . . . . . . INITIAL TESTS. . . . . . . . Voice/Data and Cipher Text Compatibility . . . . . . .4 3. . . . . Number Entry . . . Optional Manual Tests . . . . . . . . . BASIC OPERATION FROM NET PRESET . .1 3. . . . . . . . . . . . . . . . .7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 3.2 3. . . . . . . . . . . . . . . . BEFORE OPERATING THE RF-5800M-HH . . . . . . . . . . . .7. . . . . . . . . . . . . . . . . . .2 3. . Unlocking the Keypad . . . . . . . . . . . . . . . . . . . . . .2 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . . INDICATORS. . . . . . .3 3. . . . . . . . . . . . . . . . . . Automatic Test . . . . . . . . . . . . .9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . Locking the Keypad . . . AND CONNECTORS.8 3. . . . . . . . . . . . . . . . . . . . . . . .1 3. . . RADIO LOCK . .11 ii INTRODUCTION . . . . . . . . . . . . . . Optional Version Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TABLE OF CONTENTS – Continued Paragraph Page CHAPTER 3 – RADIO OPERATION 3. . . . .1 3. . . . . . . . . . . . . . . . . . . . . Unlocking the Radio . . . . . . . RADIO POWER-ON. . . . . .1 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3. . . . . . . . . . . . . . . . .2 3. . . . . . . . . . . . . . . . . . . . . . . . . Cipher Text Compatibility . . . . . .1 3.3 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking the Radio . . . .7 3. . . LT BUTTON OPERATION . . . . . . . . . . . . . . . KEYPAD LOCK . . . .9 3. . . . . . . . . . . . . . CONTROLS. . . . . . . . . . . . . . . . . . SELECTING PT OR CT . . . . . . . . . . . . . . . . . . . .9. . . . . . . . . . . . . . . . . . . . .2 Overview . . . Radio Programming Versus Temporary Overrides. . . . . . . . . . Speaker (SPKR) . .13. . . . . . . . . . . . . .5 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3. . . COMSEC . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3.CONTINUED 3. . . . . . . . . . . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . . . . . . . .13. . .15. . .15 3. . . . . . . . . . . . . . . . . . . . . . . . .Contents of a Net Preset . . . . . . . . . . . . . .12 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NET SCANNING . . . . . . . . . . . . . . . .3 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RADIO OPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMS . . . . . . . .14 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11. . . . . . . . . . . GPS . . . . . . . . . . . . . . . . Remote Control . ALERTS . . . . . . . . . . . . . . . . . . OPERATIONAL MODE MENU . . . . . .6 3. . . . . . . . . . . . . . . . . . . .TABLE OF CONTENTS – Continued Paragraph Page CHAPTER 3 – RADIO OPERATION . . . . . . LCD Display . .15. . . . . . . . . . . . . . . . . . . . .11. . . . . . . .1 3. .9 3. . . . . . . . . . Squelch (SQL) Settings . . . . .10 3. . . . . . .3 3. . . . . . . . .Preset Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 3. . . . . . . . . . . . . . . . . . . . . . . . . . Data/Voice (D/V) Settings. . . . . . . . . Beacon Mode . . . . . . . . . 3-19 3-19 3-23 3-23 3-23 3-24 3-25 3-27 3-28 3-28 3-28 3-29 3-29 3-29 3-29 3-30 3-30 3-30 3-31 3-35 3-36 3-36 iii . . . . . . . . .8 3. . . . . . . . . . . . RADIO . . . . . . . . . . . . .13. . . . . .13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3.13 3. . . . . . . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . .1 3. . . . . . . . . . . . . Select a Net Preset . . . . . . . . . . . . . LOCKSETS (Hopping Only) . . . . . . . . . . .13. . . . . . . .11. . . . .1 3. . . . . . .11. . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3. . . . . . . .7 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11. . POWER . . ZERO OPERATION . . . . . . . . . . . . . . . . . .6 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . . .13. . . . . . . . . . . HQTOD . . . . . . . . . . . . . . SAVE . . . . VAA Mode . . . . . . . . . . .15. . . . . . . .3. .5 3. . . . . . . . . Transmitting Wireless Cloning Information. . . . . . . . . . . . . . . . . . .CONTINUED 3. . . . . . . . . . . . . . . . . . . . . . . . . .3. . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15. . . . . . . . . . . . . . . . . . . . . . .4. . . . . . . Clone Mode . . . . . . . . .15. . . . . . . . .15. . . . . .6 3. . . . . . . .3. . Repeater Retransmission Operation . . . . . . . . . . . . . . . . . . . . .8 Retransmit Mode . . . . . . . . . . . . . . . . . . . . .15. . . . . . . . . .2 3. . . . . . . . . . Retransmit Settings . . . . . . . . . . . . . . . . . . . . . . .5 3.15. . .1 4. . . . . . . . . . .15. . . . . Keypad Lock . . . . . . . . . . . . . .2 3. . . . . . ATTACHING A PC TO RADIO FOR VHF-UHF RPA PROGRAMMING . . . . .3 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . .4 3. . . . . . . . . . . .15.2 4. . . . . . . . . . . . Verifying The Status Of A Wireless Cloning Transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 3. . . . . . . . . . . . . . . . . . . . . . . .6 3. . . . . . . .15. . . . . . . . . . . . . . . PROGRAMMING MENU TREE . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37 3-38 3-40 3-42 3-44 3-44 3-46 3-47 3-47 3-49 3-50 3-50 3-50 3-50 3-50 CHAPTER 4 – RADIO PROGRAMMING 4. . . . . . . . .15. . Frequency Separation . . . . . . . . . . . . . Radio Lock . .15. . . . . . . . . . . . . . . . . . . . . . . . . . . .4.15. . . . . . . . . . . . . . . . .1 3. . . . . . . Red Analog Retransmit Operation . . . . . . . . .3 3. . . . . . . . . . . . . . . . .TABLE OF CONTENTS – Continued Paragraph Page CHAPTER 3 – RADIO OPERATION . . . . . . . .4. . . .4 iv PROGRAMMING TASK SUMMARY . . . .3. . . . . . . . . Hardware for Retransmission/Repeater Setup .15. . . . . . . .15. .3 4. . . . . . . . Test Mode. . .15. Receiving Wireless Cloning Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 3. .1 3. . . . . . . . . . 4-1 4-2 4-3 4-10 . Black Digital Retransmit Operation . . . . . . .4 3. . . . . . . . . . . . . . . . SECURITY MENU (SECUR) . . . . . . . ENCKEY Programming . . . . . . . . . . . . . . . . . . . . . . . . .1 4.2. . Net Programming Considerations . . . . . . . . . . . . .5. . . . . . . . PRIORITY Programming . . . Net Programming . . . . . . .2 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CFIG MENU . . . . . . . . . . . . PORTS MENU . . .5. . . . . . . . . . . . .2. . .1 4. . . . . . . . . . . . .4. . . . . . . . . . . . . . . . . . . . .1. . . .5. BYPASS Programming.TABLE OF CONTENTS – Continued Paragraph Page CHAPTER 4 – RADIO PROGRAMMING . . . . . . . .4 4. . . . . . . . . . . . . . . . . . . .1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 4.4. . . . . Password Programming . . . . . . . . . . . . . . . .5. . . . . . . . . . .CONTINUED 4. NORM MENU. . . .1 4. .2. .2 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixed Frequency Net Programming . . . . . . . . . . . . . . . . . . . . . .6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . View Data Port Setting .2 4. . . . . . . . . . . . . . . . . . . . . .1 4. . . . . .2 4. . . . . . . . . . . . . . . . . . . . . . . . . .7. . . . . . . . . . . . . . . . . . Frequency Hopping Net Programming.1 Level Access . . . . .8 4. . . . . . . . . . . . . . NAME Programming . . . . . . . . . . .1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 4. . . . . . . . . . . . . . . . . . . . .5. . . . . . . . . . . . . . . . . . . . . . . 4-10 4-11 4-12 4-12 4-12 4-13 4-13 4-14 4-15 4-16 4-16 4-17 4-19 4-20 4-21 4-21 4-22 4-22 4-23 4-23 4-24 4-24 v . . . .4. . SCAN MENU . . .5.1 4. . . . . .5. . . . . . . . . LOCKSET Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GENERAL Programming . . . . . . . . . . . . . . . . . .6 4. . . . . . . . . HOPSET Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . . . . . . . . . . . . . . . . .3 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . . CONFIG Programming. . . . . . . . . . . . . . . . .3 4. . . . REMOTE Port Programming . . .5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . GENERAL Settings . . . . . . . . .6. . . . . . . . . . . . . . . . . . . . .5 4. . . . . . . .2. . . . . . . . . .7 4. . . . . . . . . . .7. . . . . .1 4. . . .1 4. . . . . . . . . . . . . . . . . . . . . . Scan List Programming . . . . . . . . . . . . . . . . . . . . . . .2 4. . . . . . . . . . . . . .5. . . . . . . . . . . . . . . . . . . . . . . .8. Programming Situational Awareness Settings . . . . . . . . .8. . .8. . . . . . . . . . . . . . . . . . . . . .1. .1 5. . . .3. . . . . . . . . . 4-25 4-27 4-27 4-28 4-28 4-28 4-28 4-28 CHAPTER 5 – PREVENTIVE AND CORRECTIVE MAINTENANCE 5. . .3. . . . . . . . . . . .4 4. . . . . . . . . . . . . . . .TABLE OF CONTENTS – Continued Paragraph Page CHAPTER 4 – RADIO PROGRAMMING . . . . . . . . . .7 4. . . . . . . . . . . . . Non-BIT Faults . . . . . Programming Clock Settings . . . . .2 4. . . . . . . . . . . . Programming RF-6010 Basestation Settings. . . . . . . . . . . . . . . . . . . . . . . .3 4. . .3. . . . . . . . . . . . Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BATTERIES . . . . Battery Storage and Maintenance . . . . . . .8. . . . . . . . . .2 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 5. . . . . . . . . . . . . . .9 Programming Beacon Settings . . . . Programming Short Messaging Service Settings.4 vi PREVENTIVE MAINTENANCE .CONTINUED 4. .8. . . . . . . Programming Falcon Watch™ Sensor Alert Settings . . . . . . . . Disposing of Li-ION Batteries. . . . . . . . . . . 5-1 5-2 5-3 5-3 5-3 5-6 5-6 5-7 5-8 5-9 . . . . . . . . . . CORRECTIVE MAINTENANCE . . . . . . . . .8 4.6 4. . . . . . . . . BIT Faults. . . . Recharging the Li-ION Battery Packs . . . . . . .2. . . . . . . .8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Procedures . .3. . . . . . . . . . . . . . . . . . . . . . . . .2. . . . . . . . . . . .8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . . . . . .2. . . . .1 5. . . . . . . . . . . . . . . . . . . . . . . . Programming Wireless IP Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. . . . . . . . . . . . . . . . . . . . . . . . . .1 5. . .2 5. .3 5. . .2 5. . . . . . . . . . . . . . . . . . . .1. . . . . . . . . . . . . . . . . . . .5 4. . . Programming External Device (EXT_DEV) Settings . . 2 B. . . . . . . . . . . . . . . . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . . . . . . . . . . . . . . . . .3. . . . .3. . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . .4 B. . . . . . A-1 APPENDIX B . . . . . . . . . . . . . . . . . . . . . . .3. . . . . . . . . SITUATIONAL AWARENESS (SA) . . . . . . . . Description . . . . . . . . . . . . . . . . . .4. . . .1 CHASSIS CONNECTOR PINOUT DATA . . . . . . . . . . .4 B. . . . . . . . . .ADVANCED FEATURES B. . . . . .2 B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 B. . . . . . . Busy State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. .3.3. . DIRECTED CALLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Initiating a Directed Call Using a Radio ID . . . . . . . . . . . . .3 B. .1 B. . . . . . . . . . . . . . .3 B. . . . .1 B. . . . . . . . . . .2 B. . . . . . . .3. . . .3. . . . . . . Terminating a Directed Call . . . . . . . . SA Features . . . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Internal GPS . .3 B. . . . . . . .2 B. . . . . . . . . . . . . . . . RF-6010 BASESTATION . . . . . . . .3. . . . . . . . . . . . . . . . . . .4. . . . . . . . . . Directed Calling Programming . . . . . . . . . . . . . . . . . . . . . . . . . . Radio Call Inactivity Timer . . . . . . . . . . Net Programming . .3. . . . . . . .4 B. . . . . . . . . . . . . .3 B. . . . . . . . . . . . . . . . . .1 B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .External GPS . . Breaking into a Directed Call . . . . . . . . . . . . . . . . . . . . . . . . .2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA Configuration . . . . . Error Messages and Corrective Actions.2. . . . . . . . . . . . . . .1 B. . . . . . . . . .2 INTRODUCTION . . . .2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . .4.TABLE OF CONTENTS – Continued Paragraph Page APPENDIX A A. . . . .1 B. . . . . . . SA Operation . . . SA Configuration .2. B-1 B-5 B-6 B-6 B-7 B-8 B-8 B-9 B-9 B-9 B-9 B-11 B-12 B-12 B-13 B-14 B-14 B-24 vii . . . . . . . . . . . . . . . . . . . . GPS External Mode . . . . . . . . . . . . . . . . . .2 B. . . . .1 B. . . B-25 B-26 B-27 B-28 B-29 B-29 B-30 B-32 B-32 B-34 B-35 B-36 B-36 B-37 B-38 B-39 B-40 B-44 B-44 B-45 B-45 B-45 . . . .6. . . . . . . . . . . . . . . . . . . . . . . . . . .CONTINUED B. . . . . . . . . . . . . . . . . . . . . . . . . . . .1 B. . . . . . . .6. . . . . Viewing a Received SMS Messages . . . . . . . . .4 B. . . . . .2 B. . .1. . . . . . . . . . . . . .5 B. . .6. . . . . . . . .1 B. . .3 B. WIRELESS IP NETWORK. . . . . . . . . . . .4. . . . . . . . . . . Sending New SMS Messages . . . . . . . . . . . . . . . . . . Sensor Alert Operation. . . . . . . . . .1. . .7. . . . . . . . . Deleting SMS Messages . . . .1 B. . . . .5. . . . . . . . . . . . Filtering Alert Messages. . . .TABLE OF CONTENTS – Continued Paragraph Page APPENDIX B . . . .4 B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B. . . . . . . . . . . .Connecting the Units. . . . . . . . .4. . .1 B. . .1. . . . . . . . . . .3 B. . . . . .1 B. . . . . . . . . . . . . . . . . .1 B. . . .6. . . . . Stored Alert Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Theory of Operation . . . .4. . . . . . . . . . . Forced Reporting of GPS/SA Information . . . . .2. . . . . . . . . . . . . . . Viewing SA Information . . . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . .1 B. . . . . Forwarding SMS Messages .1. . . .4. .ADVANCED FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display All Alert Messages. . . . . . . . . . . . . . .6 B. . . SHORT MESSAGING SERVICE (SMS) . . . . . . . . . . . . . . . . . . . . . . FALCON WATCH™ SENSOR ALERTS .2 B. . . . . . . . .3. . . . . . .6. . . Deleting Alert Messages . . . . . .6. Network Programming . . . . . . . . . Composing SMS Canned Messages . . . . . . . . . . . . . . . . . . .1. . . . .3. . . . . . . . . . . .1. . . . . . . . .5. . . . . . . .4. . . . . . . . . . . Reviewing Alert Messages. . . . . . . . . . . .7. . . Short Message Service Programming . . . . . . . . . . . .7. .1 B. . . . . . . . . . . . . . . . . SMS Operation. . . . . . . . . . . . . . . . . .7 B. . . . . . . .7. . . . . . . . . . . . . . . . . . . . . . . .2. . . . . .7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B. . . . .7. . . . . .2 viii Using the External GPS Receiver . . . . . . . . . .6. . . . . .7. . . . . . . . .4 B. . . . . . . . . . . . . .CONTINUED B. . . . . . . . . . .3 B. . . . . . . .7. Tamper Alert Reports . . . . . . . . . .7. . . . . . . . . . . . . . . . . . . . . . . . . . .3 B. . . . . . . . . . B-46 B-46 B-47 B-47 GLOSSARY INDEX ix . . Sensor Alert Programming . . . . . . . . . . . . .5 Deleting All Alert Messages . . . . . . . . . . . .TABLE OF CONTENTS – Continued Paragraph Page APPENDIX B . . . . Low Battery Alert . . . .2. . . . . . . . . . . . . .ADVANCED FEATURES . . . . . . .7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RF-5800M-HH Options Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical Equipment Setup and Teardown . . . . . . . . . . . . Other RF-5800M-HH Keypad/Display Button Menu Trees . . . . . . . . . . . . . . . . . . . . . . Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Red Analog Retransmission Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black Digital Retransmission Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repeater Operation . . . . . . . . . . . . . . . . . . . . Radio Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indicators. . . . RF-5800M-HH Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMS Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Zero Menu . . . . . . . . . . . . . . Basic Wireless IP Network . . . . . . . . . . . . . . . . . . . . . . Items Included with the RF-5800M-HH . . . . . . . . . . . . . . . . . . . . . . . Retransmission/Repeater Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example of a Telephony Network. . . . . . . . . . . . . . . . . . . . . . . . . . Net Preset and Frequency/Hopset Screen in Transmit (Fixed Frequency Shown) . . . . . . . . . . . . . . . . . . . . . and Connectors for RF-5800M-HH (20 m Model) . . . . . . . . . . . . . . . . . . . Net Preset and Frequency/Hopset Screen in Receive (Fixed Frequency Shown) . . . . . . . . . . Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 2-4 2-11 3-3 3-4 3-13 3-14 3-16 3-21 3-22 3-26 3-27 3-34 3-35 3-39 3-41 3-43 3-45 A-5 B-30 B-31 B-33 B-42 . . . . . . . . . . .LIST OF FIGURES Figure 2-1 2-2 2-3 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 A-1 B-2 B-3 B-4 B-5 x Page RF-5800M-HH Models . Battery Display . . . . . . . . . . Typical Sensor Report Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . RF-5800M-HH Mode>Test Menu . . . . . . . . . . . . . . . . and Connectors for RF-5800M-HH (2 m Models) . . . SCAN Displays. . . . . . . . . . . . . . . . . . . . . . . . . Error Messages and Corrective Actions. . . . 1-6 1-8 2-1 3-5 3-17 5-1 5-2 5-4 5-4 5-7 A-1 A-2 A-3 A-4 A-5 B-11 B-17 B-43 B-47 xi . . . . . . . . . . . . . . . . . . . . . . . . . DATUM Abbreviations and Descriptions . . . . . . . . . . . . . . . . . . . . . AUDIO Connector (2 m Models) . . . . . . . . . . . . . . . . . . . Indicators. . . . . . . . . . . . . Daily Preventive Maintenance Checks and Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voice/Data Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alert Messages. . . . . . . . . . . . . . . . . VHF-UHF ANTENNA Connector . . . . . . . Items Included With the RF-5800M-HH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weekly Preventive Maintenance Checks and Services . . . 2 M and 20 M Connectors and Mating Connector Part Numbers . . Run-Time Warnings . . . . . . . . . . . . . . . . . . . . . . Tamper Alerts . . . . . .LIST OF TABLES Table 1-1 1-2 2-1 3-1 3-2 5-1 5-2 5-3 5-4 5-5 A-1 A-2 A-3 A-4 A-5 B-1 B-2 B-3 B-4 Page RF-5800M-HH Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radio Model Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RF-5800M-HH Typical Battery Life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-BIT Troubleshooting . . . . Side Connector Pinouts . . . and Connectors. . . . . . . . . . . . . . . . . RF-5800M-HH Controls. . . . . . . AUDIO Connector (20 m Models) . . . . . . . . . . . . xii .This page intentionally left blank. a hissing sound is heard.If using the blade antenna.4 .Paragraph 2.To avoid hearing damage.2. tighten onto radio by turning the base adapter to avoid damage to Radio Frequency (RF) antenna connector on the transceiver. check the volume level before using the radio.Paragraph 2.Do not crush. CAUTION .1 .Paragraph 2.2.1 . loosen from the radio by turning the base adapter to avoid damage to Radio Frequency (RF) antenna connector on the transceiver.3 . • WARNING .7 .1 SAFETY PRECAUTIONS All safety precautions necessary for the protection of personnel and equipment are cross-referenced in the following list.Use only battery chargers approved by Harris.If using the blade antenna. and an irritating smell occurs.2. 1-1 . move the equipment to a well-ventilated area if possible.If the battery becomes hot.2. and never modify the battery or charger. • WARNING . • WARNING .Paragraph 3.CHAPTER 1 EQUIPMENT DESCRIPTION 1. Read these items in their entirety before performing the referenced procedure. • CAUTION .Paragraph 2. reverse polarity incinerate. • • CAUTION .Acid contaminates lithium-ion batteries.Paragraph 2.Paragraph 2.1 . • WARNING . The WARNING or CAUTION is referenced to the paragraph number where it is used in the manual.1 . and a brief subject phrase indicating the content is provided. disassemble. or mutilate the lithium-ion battery. Do not attempt to recharge a disposable lithium battery. manpack.Paragraph 5.Do not dispose of lithium-ion batteries in uncontrolled trash. 1.2 • WARNING .3.3 . and Amplitude Shift Keying (ASK) data. WARNING . NOTE The radio supports Continuously Variable Slope Delta (CVSD) voice and data communications only with other Harris Falcon II radios that use this mode. mobile. PURPOSE OF THIS MANUAL This operation manual provides the user with operating instructions for the RF-5800M-HH Export Multiband Handheld Radio (often referred to throughout this manual as RF-5800M-HH).Avoid contact with antennas in retransmit mode to prevent electrical shock and RF burns. as well as technical information required to support Level I (operator) Maintenance. 16 kbps Wideband Frequency Shift Keying (WBFSK).Paragraph 3.1. ground-to-ground. • • WARNING . lightweight package that maximizes user mobility. Supported modulation modes are Frequency Modulation (FM).3 . The RF-5800M-HH allows selectable transmit power levels. Communications can take place with handheld.15. and operates from a single. The RF-5800M-HH can quickly shift between Line-of-Sight (LOS). Amplitude Modulation (AM).3 EQUIPMENT DESCRIPTION The RF-5800M-HH is an advanced mulitband handheld radio which provides reliable tactical communications performance in a small.2 . and fixed-site stations in either encrypted or unencrypted modes. 1-2 .3.Paragraph 5. rechargeable Lithium-Ion (Li-ION) handheld battery. and Ultra High Frequency (UHF) ground-to-air communications in the frequency band of 30 MHz to 512 MHz. The radio also supports remote control operation from a separate terminal. A fixed frequency net is made up of a frequency. mode of operation. Up to 25 user-defined net presets provide complete frequency programming and other radio parameters including radio operating mode.A menu driven interface is used to access the radio operation and features. Additionally. which must be synchronized between the transmitter and receiver. Communications Security (COMSEC) keys. The RF-5800M-HH is available in several model configurations including: with or without Global Positioning System (GPS). A frequency hopping net is similar to a fixed frequency net except that the radio continuously changes the operating frequency. Harris Citadel I® or Citadel II® encryption for secure voice and data. it is referring to the salt water submersion rating in meters (not wavelength). and a net name. squelch setting. Quick selection of five nets can be done using the knob on top of the radio. the RF-5800M-HH provides Built-In Test Equipment (BITE) for radio operational test and battery checks. and 2 meter (m) or 20 meter (m) submersible ratings. green or black finish. The RF-5800M-HH supports two types of radio net structures. and Transmission Security (TRANSEC) keys. as well as a hold-up battery circuit to maintain programmed information when powered off. transmit power level. 1-3 . NOTE Whenever 2 m or 20 m is discussed in this manual. 1.4 FEATURES The RF-5800M-HH offers the following features: • • • • • • • • • • • • • • • • 1-4 Fixed frequency and Quicklook 1A frequency hopping operation Optional Havequick frequency hopping Harris Citadel I® or Citadel II® encryption for secure voice and data operation Wireless cloning of radio configuration Net Scanning mode Situational Awareness position reporting Directed Calling Wireless Internet Protocol (IP) Short Messaging Service (SMS) Falcon Watch™ Sensor Alert Messaging DC Antenna Bias menu to support the RF-3162-AT001 VHF-UHF Dipole antenna Automatic whisper operation Cross-band and cross-mode retransmit operation Search and Rescue (SAR) beacon Operation with optional RF-5800M-V520 Vehicle Adapter Amplifier (VAA) Operation with optional RF-5800M-V500 Vehicle Adapter Amplifier (VAA) . black finish RF-5800M-HH115 Multiband radio. available in both 2 meter (m) or 20 meter (m) model configurations • Direct Point-to-Point Protocol (PPP) network connection to Harris RF-6010 for both telephony and IP data transfer • • RF-5800M-HH supports telephony calls when connected to a RF-6010 Basestation 1. black finish RF-5800M-HH101 Multiband radio. 20 meter submersible. no internal GPS.• Radio lock entered from front panel for RF-5800M-HH. with GPS. green finish RF-5800M-HH111 Multiband radio. green finish RF-5800M-HH004 Multiband radio. green finish RF-5800M-HH002 Multiband radio. black finish RF-5800M-HH114 Multiband radio. no internal GPS. with GPS. with internal GPS.5 Jerk and Run cable sense functionality for vehicle mounted RF-5800M-V520 VAA CONFIGURATIONS The RF-5800M-HH radio is available in the following configurations: • • • • • • • • • RF-5800M-HH001 Multiband radio. 20 meter submersible. no internal GPS. green finish RF-5800M-HH011 Multiband radio. with internal GPS. black finish 1-5 . no internal GPS. green finish RF-5800M-HH104 Multiband radio. with GPS. operator selectable) 1-6 .14 VDC.25. fully programmable (presets numbered 0 .975 MHz . 10. high .6 SPECIFICATIONS Table 1-1 lists the specifications for the RF-5800M-HH. Continuous Tone Coded Squelch System (CTCSS).00000 MHz to 512. or no squelch Radio Net Presets Up to 25. 2. RF-5800M-HH Specifications Function Specification GENERAL Frequency Range 30. 150 Hz tone.operator selectable) AM: 1.24) Frequency Hopping Quicklook 1A RF Input/Output Impedance 50 ohms nominal. 6.Frequency Hopping Modulation FM. Because Harris engineers continuously strive to improve all aspects of Harris equipment. (low. (low. CVSD digital voice or clear voice FM Deviation 5 kHz.Fixed Frequency 25 kHz . and 8 kHz Squelch Noise. Table 1-1. ASK.13 VDC) Transmitter Power Output FM: 0.Fixed Frequency 30.6 .5 kHz.00000 MHz to 511. digital squelch. medium. specifications are subject to change without notice. high . degraded performance outside of 10 . unbalanced Power Input Battery. medium. 5 watts.00000 MHz . AM. 5 watts.Quicklook 1A Hopping Frequency Resolution 10 Hz .1. 2.8 VDC nominal (Acceptable range: 9. WBFSK. ) above sea level for one hour.42 lbs.) Weight 1.) including battery and short antenna Altitude Operate at 4545 meters (15.1 H x 2.25 D in.) per MIL-STD-810F RF-5800M-HH models rated for 20 meters (66 ft.7 D cm.6 ft. 1-7 .) 2. including battery Storage Temperature Range -30° C to +70° C (-22° F to +158° F).) per MIL-STD-810F 1.1 H x 5.4 W x 23.1 H x 5. (7. (7.91 W x 9.000 ft.91 W x 9. including battery Size (including battery): With internal GPS Without internal GPS 20 m models 2.1 in. (7.1 kg (2.0 D cm.7 VOICE/DATA COMPATIBILITY Refer to Table 3-2 for information on the capabilities of the RF-5800M-HH for voice or data in each modulation and radio mode. RF-5800M-HH Specifications (Continued) Function Specification Operating Temperature Range -20° C to +60° C (-4° F to +140° F).Table 1-1.9 cm.) Same as above except width is 3.1 H x 1. per MIL-STD810F Salt Water Submersion RF-5800M-HH models rated for 2 meters (6.4 W x 23.97 D in. fixed-frequency modes with other UHF and Very High Frequency (VHF) radio systems. only utilize squelch types that ALL radios can support.1. When introducing older radio equipment to the net. Table 1-2. only use frequencies that ALL radios can support. Table 1-2 provides a list of compatible Harris radio models and radio modulation types and modes. The RF-5800M-HH is interoperable in non-secure. several net compatibility issues must be considered when planning the net: • Frequency .Older radio equipment may not support data or digital voice operating modes. • Data/Voice Mode . When introducing older radio equipment to the net.Older radio equipment does not support 10 Hz frequency resolution of the RF-5800M-HH in fixed mode.8 COMPATIBILITY Successful communications depends on using the correct encryption type and compatible radios. When communicating with older radio equipment. When introducing older radio equipment to the net. Radio Model Compatibility Encryption Radio Model Modulation/Mode CVSD Voice Voice Citadel** Data Frequency Hopping FM AM FSK ASK FSK ASK RF-5800U-HH * * * * * * * RF-5800U-MP * * * * * * * RF-5800M-HH 1-8 .Older radio equipment does not support digital squelch. only utilize operating modes that ALL radios can support. • Squelch . 1 for a list of Harris cables. 1-9 .1 for connector pinout information. For mating connector part numbers. Refer to Paragraph A.Table 1-2. 1. Refer to Paragraph 2.1. refer to Table A-5.9 COMPATIBLE CABLES AND CONNECTORS Several cables are available for connecting external equipment to the RF-5800M-HH. Radio Model Compatibility (Continued) Encryption Radio Model Modulation/Mode CVSD Voice Voice Citadel** FM AM FSK ASK Data FSK ASK Frequency Hopping RF-5800M-MP RF-5800V-HH * * * * RF-5800V-MP * * * * = Compatible * = Compatible when using compatible frequencies **RF-5800M-HH radios provide support for both Harris Citadel I® and Harris Citadel II® encryption and Citadel II® is backwards compatible with Citadel I®. This page intentionally left blank. 1-10 . Items Included With the RF-5800M-HH Item Part # RF-5800M-HH Radio Assembly. green 12046-1000-03 Model RF-5800M-HHXXX 001 011 101 x 111 * * * 002 004 104 114 * 115 x x x x 2-1 . green 12046-1000-01 RF-5800M-HH Radio Assembly.1 ITEMS INCLUDED WITH THE RF-5800M-HH Table 2-1 provides a list of items included with each RF-5800M-HH model. 2. the system level documentation takes precedence. Table 2-1. Table 2-1 includes both Harris Citadel I® and Harris Citadel II® models and Citadel II® is noted with an asterisk (*).CHAPTER 2 SETUP AND TEARDOWN NOTE In applications where the RF-5800M-HH is installed in a radio system that includes other equipment. Figure 2-1 and Figure 2-2 show all of the items included with the various RF-5800M-HH models. black 12046-1000-02 RF-5800M-HH Radio Assembly w/GPS. Items Included With the RF-5800M-HH (Continued) Item Part # Model RF-5800M-HHXXX 001 011 101 RF-5800M-HH Radio Assembly w/GPS. black 12046-1000-08 RF-5800M-HH Radio Assembly 20 m 12046-6500-01 MB-HH Short Whip Antenna 12041-2700-01 MB-HH Short Whip Antenna.Table 2-1. Black 12041-2100-01 Operator Card 10515-02344100 MB-HH GPS Antenna 12041-6550-01 2-2 111 * * * 002 004 104 114 x x x 115 x x x * x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x . 20 m submersible 12046-2700-01 MB-HH Blade Antenna 12011-2700-01 x Rechargeable Lithium-Ion (LiION) Battery. Green 12041-2100-02 x Rechargeable Lithium-Ion (LiION) Battery. NO INTERNAL GPS. GREEN/BLACK) RF-5800M-HH (20 M. WITH OR WITHOUT GPS.RF-5800M-HH (2 M. GREEN/BLACK) CL-0234-4200-0001B Figure 2-1. GREEN/BLACK) RF-5800M-HH (2 M. WITH INTERNAL GPS. RF-5800M-HH Models 2-3 . GPS ANTENNA (12041-6550-01) OPERATOR CARD (10515-0234-4100) RECHARGEABLE Li-ION BATTERY (12041-2100-XX) BLADE ANTENNA WITH BASE ADAPTER (12011-2700-01) MB-HH SHORT WHIP ANTENNA SUBMERSIBLE (12046-2700-01) MB-HH SHORT WHIP ANTENNA (12041-2700-01) Figure 2-2. Items Included with the RF-5800M-HH 2-4 CL-0234-4200-0004B . 1 Optional Items Optional items available for the RF-5800M-HH include: • • • • • • • • • • • • • • • • RF-3161-AT001 Body worn dipole antenna (12006-2400-02) Modified H-250 Handset (10075-1399) Headset (12011-0400-xx) RF-5853-CH001 Single-bay charger (12011-2400-01) RF-5853-CH002 Two-bay charger (12011-3100-01) RF-5853-CH006 Six-bay charger (12011-2300-01) Black or Green Battery options for RF-5800M-HH radio models (12011-2100-01 and -02) Data Cable. Side Connector to DB25 Synchronous (12011-0210-A006) Config/Fill Cable. Point-to-Point Protocol (PPP) Cable (12011-0775-A003/A006/A007) RF-6550V-PK002 Radio Programming Kit Radio Holster (RF-5932-CA001 Camo) (RF-5932-CA002 Black) Flipdown Radio Holster (RF-5933-CA001 Camo) (RF-5933-CA002 Black) Handset Radio Accessory bag (12041-1595-01) GPS Antenna Assembly (12041-6550-01) 2-5 .1. Side Connector to DB9 Remote (12011-0200-A006) Retransmit cable (12011-0230-A050) Tactical Internet.2. 2.1 Battery Safety Observe the following warnings and cautions: WARNING Do not crush. Refer to Paragraph 5.2 BATTERY INSTALLATION The RF-5800M-HH includes a rechargeable Li-ION battery pack. The following paragraphs contain operating warnings and cautions about the battery. other antennas may be used if they have a 50-ohm input impedance and use a Sub-Miniature B (SMB) connector.3 for battery maintenance information. For the GPS antenna. Do not expose to fire or temperatures above 160° F (71° C). or mutilate the lithium-ion battery. reverse polarity. disassemble. The blade antenna is designed for use over the range of 30 MHz to 108 MHz.512 MHz The RF-5800M-HH can operate with the whip antenna over the entire 30 MHz to 512 MHz range of the radio. 2. 2-6 . incinerate. Other antennas may be used if they have a 50-ohm input impedance and use a Threaded N-Connector (TNC).2.• • RF-5852-CH001 Vehicular Charger/Power Supply Broadband Antenna 30 . or an irritating smell occurs. or attempt to charge a disposable battery. and never attempt to modify the battery or charger. Doing so may result in injury or death and/or damage to the battery and the radio. such as screwdrivers. Contact your local authority for clean up instructions. WARNING Use only chargers approved by Harris. a hissing sound is heard. Any trace of acid or acid fumes will permanently damage lithium-ion (Li-ION) batteries on contact. Every effort must be made to keep lithium-ion batteries isolated from lead-acid batteries because lead-acid batteries contain sulfuric acid. DO NOT use the same tools and materials.WARNING If the battery becomes hot. CAUTION ACID CONTAMINATES LITHIUM-ION BATTERIES. clear the area. syringes. 2-7 . and gloves for both types of batteries. hydrometers. wrenches. 2.2.2 Antenna Connections Several types of antennas may be connected to the top of the RF-5800M-HH. The GPS antenna (12041-6550-01) is only available for RF-5800M-HH models that support GPS capability. Likewise, the 20 m Short Whip Antenna (12046-2700-01) is only available for RF-5800M-HH 20 m models. The Blade Antenna with Base Adapter (120112700-01) and the MB-HH Short Whip Antenna (12041-2700-01) are available to all RF-5800M-HH models. Refer to Table 2-1 for a list of items included with each RF-5800M-HH model type and see Figure 2-2. 2.2.3 Data Cable Connections Several types of data cables may be connected for programming the RF-5800M-HH. There is a side connector on the RF-5800M-HH for data cable connection. Refer to Table 2-1 for a list of items included with each RF-5800MHH model type. 2.2.4 Audio Connections A six pin audio connector, located on the top of the RF-5800M-HH, is available for audio (microphone) connections. Refer to Table 2-1 for a list of items included with each RF-5800M-HH model type. 2.2.5 GPS Connections If equipped with internal GPS functionality, the GPS antenna (12041-6550-01) connects to the top of the RF5800M-HH. GPS is an optional configuration. Refer to Table 2-1 for a list of items included with each RF-5800MHH model type and see Figure 2-2. 2-8 2.3 EQUIPMENT SETUP See Figure 2-3. Perform the following procedure to set up the RF-5800M-HH: a. The lithium-ion battery has a quick twist mount for easy connect and disconnect. Attach battery to transceiver by seating the battery on the base of the radio at an angle to the base, and then twist the battery into position in a clockwise direction as viewed from the bottom of the battery. The battery latch on the side of the radio snaps into the lock position when the battery is properly positioned on the radio. Refer to Paragraph 5.3 for information on batteries and recharging batteries. b. Connect the optional handset, if used, to the audio connector on top of the transceiver. c. Screw either the blade antenna or short whip antenna to the antenna connector on top of the transceiver. • If using the blade antenna, connect antenna base to the transceiver by holding and turning the adapter body. Connect antenna to base. CAUTION If a blade antenna is used, attach base to transceiver by holding and turning the base adapter. Holding and turning the blade antenna can damage the RF antenna connector on the transceiver. • d. The short whip antenna does not require an antenna base adapter and can be connected directly to the antenna connector on the transceiver. If the radio is equipped with internal GPS, screw the GPS antenna into the GPS connector on top of the transceiver. 2-9 2.4 EQUIPMENT TEARDOWN See Figure 2-3. Perform the following procedure to tear down the RF-5800M-HH: a. Zeroize the radio to erase communications plan, Transmission Security (TRANSEC) information, and Communication Security (COMSEC) information. Refer to Paragraph 3.12. b. Turn the radio function switch to the OFF position. c. Disconnect the antenna from the antenna base (if used). If no antenna base is used, disconnect the antenna from the antenna connector on the radio. CAUTION If a blade antenna is used, remove base from transceiver by holding and turning the adapter. See Figure 2-2. Holding and turning the blade antenna can damage the RF antenna connector on the transceiver. 2-10 d. Disconnect the antenna base (if used) from the antenna connector. e. Disconnect the handset (if used) from the audio connector. f. If equipped with internal GPS, disconnect the GPS antenna from the GPS antenna connector. g. Remove battery from the transceiver by sliding the battery latch up towards the data connector. Hold the battery latch in this raised position while rotating the battery in the counterclockwise direction as viewed from the bottom of the battery. Refer to Paragraph 5.3 for information on battery life, recharging batteries, and proper handling and disposal of batteries. Typical Equipment Setup and Teardown 2-11 .HANDHELD WHIP ANTENNA GPS ANTENNA RF-5800M-HH MULTIBAND TRANSCEIVER RECHARGEABLE Li-ION BATTERY BATTERY LATCH CL-0234-4200-0002 Figure 2-3. 2-12 .This page intentionally left blank. The user should first review Paragraph 3.4 Radio lock/unlock .6 Test radio .7.3.Paragraph 3. indicators and connectors.Paragraph 3.12 3-1 .11 Some operations can be performed at any time during normal operations and consist of: • • • Optional tests .4 Display lamp operation .Paragraph 3. Paragraph 3.8 Zeroize radio .7.CHAPTER 3 RADIO OPERATION 3.5 Keypad lock/unlock . Paragraph 3.3 to become familiar with the radio controls. are performed in the following order: • • • • • • Power on radio .2.2 OPERATION TASK SUMMARY Radio operation tasks.Paragraph 3.Paragraph 3.7.Paragraph 3.Paragraph 3.7 Select Plain Text (PT) or Cipher Text (CT) .1 INTRODUCTION This chapter provides instructions on how to operate the RF-5800M-HH.Paragraph 3. 3.10 Perform basic operations using net presets . in general.Paragraph 3. INDICATORS. Short Messaging Service (SMS). 3-2 .• • • • • Set radio options . Figure 3-2 shows the controls. 3. and connectors for the 2 m models of the RF-5800M-HH.15.4 NOTE Advanced features covered in Appendix B include Directed Calling. it is referring to the salt water submersion rating in meters (not wavelength).15. AND CONNECTORS Figure 3-1 show the controls. Situational Awareness (SA).Paragraph 3. NOTE Whenever 2 m or 20 m is discussed in this manual.Paragraph 3. Wireless IP Network.3 Clone mode .Paragraph 3.1 Retransmit mode .Paragraph 3. Table 3-1 describes the controls. indicators. and Falcon Watch™ Sensor Alerts. and connectors for all models. indicators.15.14 Remote control mode .3 CONTROLS. and connectors for the 20 m models of the RF-5800M-HH. RF-6010 Basestation support. indicators.13 Net scanning .Paragraph 3. and Connectors for RF-5800M-HH (2 m Models) 3-3 . Indicators. Controls.13 8 4 5 7 6 9 3 2 1 12 11 10 CL-0234-4200-0003 Figure 3-1. Indicators. and Connectors for RF-5800M-HH (20 m Model) 3-4 . Controls.13 5 6 7 4 9 3 2 1 12 11 10 CL-0234-4200-0005A Figure 3-2. 3 Volume Control UP arrow increases volume. RF-5800M-HH Controls. Z-ALL Zeroizes all programmed variables.) 3-5 . 4 Microphone Built-in microphone. DOWN arrow decreases volume. FP Places the radio in Front Panel (FP). 5 Audio Connector Provides a connection for an optional handset or headset. requires momentarily moving toggle switch to the “Z” position. SCAN Places the radio in Scan mode.Table 3-1. (2 m models only) (Z-ALL brings up the ZERO ALL MENU on 20 m models only. Figure 3-2) Control/Indicator Function 1 Monitor Toggles squelch on and off. 6 Antenna Connector Provides a 50-ohm antenna port for a Threaded N-Connector (TNC). and Connectors Key (Figure 3-1. permitting access to all nets and keypad functions. if scan is enabled. 2 PTT Push-To-Talk switch. including encryption variables. Indicators. 7 Function Switch OFF Turns RF-5800M-HH off. 1 through 5 Selects radio presets 1 through 5. . Refer to Paragraph B. [OPT] (7 STU) Provides access to the radio's options menus. See Figure 3-3. 10 Battery Latch Releases battery for removal. Directed Calling. Figure 3-2) 8 Control/Indicator Toggle Switch (2 m models only) PT Places the radio in Plain Text (PT) mode. 9 Side Connector Provides connection for remote control operations. See Figure 3-9.11. Also requires function switch in Z-ALL position to zeroize (Momentary). [MODE] (3 GHI) Allows the operator to change the radio's operating mode. Z Zeroizes all programmed values.Table 3-1. external GPS.8 and see Figure 3-5.3. Refer to Paragraph 3. 11 Keypad Buttons 0 (zero) 3-6 Function The Circular Arrow button shows alternate displays. [LT] (2 DEF) Provides access to the Keypad/Display backlight control menu. CT Places the radio in the Cipher Text (CT) encryption mode. including COMSEC and TRANSEC variables. Refer to Paragraph 3. RF-5800M-HH Controls. Indicators. [ZERO] (5 MNO) Provides access to the radio's zeroize menus. See Figure 3-8. and Connectors (Continued) Key (Figure 3-1. [CALL] (1 ABC) Used for Wireless IP. or data device. 12 Display Displays operational and programming screens. 3-7 . and activates the previous menu. [CLR] Returns a field to its previous value. Selects scroll field choices or locks in entry field data. and Connectors (Continued) Key (Figure 3-1. S and T buttons Allows the operator to step through a scroll field list. Indicators. Figure 3-2) Control/Indicator Function [PGM] (8 VWX) Provides access to the radio's programming menus. [PRE +/-] Scrolls the operator through the programmed nets when the mode switch is in the FP position.Table 3-1. _ and ` buttons Allows the operator to move the cursor to the left or right. 13 GPS Antenna Connector Antenna connector for internal GPS. [ENT] Enter. Also will terminate a call while in a Directed Call. or to select a new menu field. See Figure 4-1. RF-5800M-HH Controls. Press the 1 button once to enter an A. the button sequence is slightly different. press the 1 button once.1 Number Entry Alphanumeric fields are used to enter alphanumeric strings such as net names. only the next character to be updated flashes. For example. This automatically advances the cursor to the next position. • Each numeric button on the keypad (except 0) is assigned up to three letters of the alphabet. the right arrow button must be pressed to advance the cursor. the CLR button deletes all digits. • To advance the cursor to the next position.3. • • Blank spaces in a text string are entered by pressing the 0 button twice. 3-8 . etc. and passwords. Once a character is entered. The CLR button backspaces one digit and then clears all digits to the right of the cursor. and C. press the 1 button twice to enter B. the entire field flashes. and press the 1 button four times to enter a 1. • If two consecutive letters need to be entered from the same button. press the 1 button three times to enter a C. security. To enter a 1 in a field. press the 1 button twice. NOTE When using SMS.3. to enter an A. When selecting an alphanumeric field. This flashing character is the cursor. B. NOTE When using SMS. the 1 button is also assigned the letters A. another button must be pressed. NOTE The keypad may be locked to prevent accidental button operation. This allows the radio to be used with simple “Jerk and Run” operation. 3-9 . See Figure 3-11. 3.2. or FP position. and press [ENT]. rotate the function switch from OFF to either the 1 . unlock the keypad as described in Paragraph 3. allowing for CT and PT audio connections. When the test is complete. The top function switch will remain operable even with the radio locked.6.3. the net preset screen is displayed. 3. set the operating mode to VAA (refer to Paragraph 3. c. b.8).4 RADIO POWER-ON To power on the RF-5800M-HH.5. Press the [MODE] button.5.5 RADIO LOCK The Radio Lock function provides the capability to completely disable all keypad and all push-button functions of the radio. RADIO LOCKED will be seen on the display.15. This eliminates the potential for any inadvertent key presses while the radio is turned on. When using the RF-5800M-HH with the optional RF-5800M-V520 Vehicular Adapter Amplifier (VAA).1 Locking the Radio Perform the following procedure to lock the radio: a. SCAN. This initializes the radio and performs a self-test. Use the up/down arrow buttons to select RADIO LOCK. Before proceeding with keypad functions. b. See Figure 3-11.5.2 Unlocking the Radio Perform the following procedure to unlock the radio: 3. MIC Push-to-Talk (PTT). 3-10 . KEYPAD LOCK The Keypad Lock function provides the capability to lock the radio keypad. The Keypad Lock security function reduces the potential for inadvertent key presses that may adversely affect radio operation or programming. Press the [CLR] button five times. The radio controls will be unlocked.1 Locking the Keypad Perform the following procedure to lock the keypad: a. or Zero (0) button. Press the [MODE] button.3.6. b. squelch and volume controls to operate. 3. and press [ENT]. Use the up/down arrow buttons to select KEYPAD LOCK. NOTE Locking the keypad does not disable the Monitor (squelch button). Volume controls. while still allowing the PTT.6 a. Press the [MODE] button. If there is no password.1 for information on remote control. remote control should be turned off prior to turning off keypad lock.3. check the volume level before using the radio. Enter the programmed operator security level 0 password and press [ENT] to unlock the keypad.2 Unlocking the Keypad Perform the following procedure to unlock the keypad: a. 3-11 .7 INITIAL TESTS The following paragraphs provide tests that should be performed to ensure operational readiness of the RF-5800M-HH. Refer to Paragraph 3.15.6. NOTE If remote control and keypad lock are both enabled. WARNING To avoid damage to hearing. 3. b. simply press [ENT] to unlock. . b.1 Automatic Test See Figure 3-3 for the Mode>Test menu tree. Use the up/down arrow buttons to select TEST and press [ENT]. Use the up/down arrow buttons to select TEST and press [ENT]. Select MANUAL and press [ENT]. c. If no fault codes are displayed. 3. Use the following procedure to perform manual tests: 3-12 a. c. d. Use the following procedure to perform an automatic test: a.7. Select AUTO and press [ENT]. If the radio displays a fault code.2 Optional Manual Tests See Figure 3-3 for the Mode>Test menu tree.7. 3. refer to Chapter 5 for troubleshooting. the radio is ready for operation. Press the [MODE] button. Press the [MODE] button.WARNING To prevent electrical shock and Radio Frequency (RF) burns avoid making RF power output connections or touching the antenna while in transmit mode. b. 4. RF-5800M-HH Mode>Test Menu 3-13 . AUDIO also tests SPKR (internal) and AUXSPKR (side connector) capability by generating an audible beep that continues until [CLR] is pressed.3 V HARDWARE USE BUTTONS TO SCROLL THROUGH INSTALLED ASSEMBLIES FIRMWARE USE BUTTONS TO SCROLL THROUGH INSTALLED FIRMWARE REVISION LEVELS OVM SERIAL VERSION: V#. Refer to Paragraph 3. Refer to Paragraph 3. 2. and displays an indicator bar showing the level.Tests backlight settings. KEYPAD .# FEATURE: (PART #) R/T SERIAL NUMBER ###### F-0234-4200-0004 Figure 3-3.The keypad test displays each key number as it is pressed. 3. BACKLIGHT .d.Tests Liquid Crystal Display (LCD) contrast settings. LCD .8 for configuring the level. GHI 3MODE OPERATIONAL MODE TEST AUTO MANUAL TEST IN PROGRESS 0% 100% AUDIO MIC SPKR AUXMIC AUXSPKR KEYPAD BACKLIGHT LCD BATTERY VERSION VOLT: 12. refer to Chapter 5 for troubleshooting. Perform individual tests as desired: 1. AUDIO .8 for configuring the level.Tests MIC (internal) and AUXMIC (side connector) input audio level. If the radio fails any of the tests. fully charged battery. Battery voltage level is also displayed numerically. The battery display shown in Figure 3-4 bases the 100% level on a new. Press the [MODE] button.3. The battery may still be used. Use the up/down arrow buttons to select TEST and press [ENT]. Do the following to perform a battery test: a. Use the left/right arrow buttons to select BATTERY and press [ENT].7. See Figure 3-4. BATTERY 12. For more information on using the battery. an old battery may not have the same capacity (or operating time) as a new battery. b. c. The radio displays actual charge capacity in percentage form with a graphical intensity meter display. This means that while a charger may indicate a full charge.3 Battery Test See Figure 3-3 for the Mode>Test menu tree. The RF-5800M-HH uses the smart features of the Li-ION battery to indicate the absolute (or true) state of charge. refer to Paragraph 5.3. Battery Display 3-14 .3 V 73% 0% 100% F-0234-4200-0005 Figure 3-4. An older battery may not indicate 100% even if fully charged. but operating time may be less than expected. The true capacity of a battery will lessen with age. then press [ENT]. a.8 a. Select and check individual versions as desired: 1. press the LT button. c.7. then press [ENT]. b. 3-15 . Press the [MODE] button. then press [ENT]. To have the backlight remain continuously on. b. To have the backlight remain on for a short time after any button is pressed. select ON. Use the following procedure to perform version tests: 3. HARDWARE 2. OVM (Option Validation Matrix) 4. FIRMWARE 3. SERIAL (serial number of radio) LT BUTTON OPERATION See Figure 3-5. To configure the Keypad/Display backlight operation.3.4 Optional Version Tests See Figure 3-3 for the Mode>Test menu tree. select OFF. Use the left/right arrow buttons to select VERSION and press [ENT]. Use the left/right arrow buttons to adjust the display contrast. then press [ENT]. d. use the up/down arrow buttons to select MOMENTARY. Use the up/down arrow buttons to select TEST and press [ENT]. intensity and contrast. Use the left/right arrow buttons to adjust the backlight intensity. then press [ENT] to exit. c. To disable the backlight. etc. or by using RF-6550V VHF-UHF Radio Programming Application software (supplied separately). addresses. traffic encryption keys.9 BEFORE OPERATING THE RF-5800M-HH Before operating the RF-5800M-HH. 3-16 . the net presets. must be established.DEF 2 LT LIGHT OPERATION OFF MOMENTARY ON LIGHT INTENSITY CONTRAST F-0234-4200-0006 Figure 3-5. Parameters can be programmed through the radio front panel per Chapter 4. Other RF-5800M-HH Keypad/Display Button Menu Trees 3. 9. Directed. Wireless IP Data/Voice (D/V) Voice Fixed Frequency Modulation VOC D/V DATA VOC D/V DATA VOC D/V DATA CLEAR CLEAR NONE CVSD CVSD NONE CVSD CVSD NONE FM WBFSK WBFSK WBFSK WBFSK WBFSK WBFSK WBFSK WBFSK 3-17 .3.1 Voice/Data and Cipher Text Compatibility Table 3-2 shows the operational mode capabilities of the RF-5800M-HH. Table 3-2. Voice/Data Compatibility Operating Mode Intended Operation Simple PT Wireless IP/ Directed CT Simple. (e.11 BASIC OPERATION FROM NET PRESET The RF-5800M-HH uses net presets to simplify radio operation. The following paragraphs explain how to set up and use net presets. 3-18 . where the XXXX field corresponds with the CITADEL encryption version in the radio. d. Refer to Paragraph 3.2 for the procedure to verify CT compatibility. Select HARDWARE and press [ENT]. c. Verify that the Harris part numbers match exactly. use the left/right arrow keys to scroll to the PT/CT field and then select CT or PT using the up/down arrow keys. the selection can be viewed on the LCD display. b.9.2 Cipher Text Compatibility Radios can communicate using Cipher Text (CT) only if they have exactly the same version of CITADEL encryption.g. Select TEST and press [ENT]. Select VERSION and press [ENT]. Perform the following procedure to determine CITADEL version number: 3. Use the up/down arrow buttons to scroll to the CITADEL version menu. Press the [MODE] button.) SELECTING PT OR CT On 2 m models. place the toggle switch in the PT (plain text) or CT (encrypted) position.: 10561-8010-XXXX.9. 3.3. e.10 a. On 20 m submersible models. • • NORM is displayed for simple net presets. This hierarchy lessens the amount of manually programmed parameters in the radio. 3-19 .3. use the [+PRE-] buttons to scroll through the available net presets. use the 0 • The receive signal strength meter (S-Meter) changes to display a power level meter when the RF-5800M-HH is transmitting. Some points to remember with these screens are: • To change settings. 3. • • To toggle between the system preset and channel preset screen. squelch setting.1 Overview . key. When in FP. Only the net presets that are configured and enabled (activated in list) will be selectable. The channel preset screen. is used to view and change frequency or hopset settings.Contents of a Net Preset A net preset associates an encryption key. use the _ and ` keys to scroll to the setting. shown on the bottom of Figure 3-6 and Figure 3-7. With the function switch in FP position. and power level to a fixed frequency or a hopnet. voice/data setting. The battery meter is temporarily replaced with the volume level indicator when the volume button is pressed. Net presets 1 through 5 can always be selected directly from the function switch. a user may use several encryption keys or data rates for a particular frequency or hopnet.2 LCD Display . and press [ENT] to accept changes. can only override settings when not transmitting.11. All this information can be preprogrammed into the radio and stored as a net preset for simple access. shown on the top of Figure 3-6 and Figure 3-7.Preset Screens The system preset screen. For instance.11. is used to view and change net presets. use ST to scroll choices. NOTE The radio function switch must be in the FP position to use the [+PRE-] buttons. refer to Paragraph 3. the radio places an asterisk (*) to the right of the net name on the LCD to indicate that changes have been made.11. the operator can also change Data/Voice setting and squelch type. Changing parameters in this way is called a temporary override. For more information on temporary overrides. 3-20 .NOTE Whenever the operator manually changes a preprogrammed net parameter.6. In addition to receive and transmit frequencies. PRESSING VOLUME BUTTONS CAUSES THE VOLUME METER TO REPLACE THE BATTERY METER FOR A SHORT TIME.0 FREQUENCY RATE S3 6 9+ DATA RATE F-0234-4200-0009 Figure 3-6. PT R BAT R: 225.R/T INDICATOR (CURRENTLY SHOWING A STATIC “R” FOR RECEIVE) NET NAME DATA/VOICE MODE MODE CT/PT BATTERY NORM/HOP SWITCH SETTING METER NORM R BAT NET4 VOC CLEAR D/V PT * S3 6 SIGNAL STRENGTH METER OFF FM MOD VOICE 9+ S-METER LABEL SQL SQUELCH TYPE MODULATION MODE VOICE MODE 0 TEMPORARY OVERRIDE INDICATOR NET TYPE RECEIVE FREQUENCY TRANSMIT FREQUENCY NOTES: 1.00000 T: 225. Net Preset and Frequency/Hopset Screen in Receive (Fixed Frequency Shown) 3-21 .00000 FIX 16. THE BATTERY METER GIVES AN INDICATION OF THE CHARGE CAPACITY OF THE BATTERY. 2. Net Preset and Frequency/Hopset Screen in Transmit (Fixed Frequency Shown) 3-22 .R/T INDICATOR (CURRENTLY SHOWING A FLASHING “T” FOR TRANSMIT) POWER METER NORM T BAT NET4 VOC PT CLEAR D/V FM MOD VOICE OFF SQL 0 PT T BAT R: 225.00000 T: 225.0 FREQUENCY RATE F-0234-4200-0010 Figure 3-7.00000 FIX 16. If the radio is changed to PT from CT when VOC or D/V is selected.2 for details on configuring the radio for CTCSS. Noise and Tone Squelch can be modified from the SQL field. analog tone squelch. for use with repeater systems that utilize CTCSS. Digital squelch requires that the radio receive a specific digital waveform in order to break the radio's squelch.1 for compatibility. Digital squelch is only available if the radio is in the CT position.2. The choices correspond to the types of information that can be transmitted and received. Refer to Paragraph 3. Analog noise squelch requires a signal that is strong enough to break the radio's squelch be received on the radio's receive frequency.3. or DATA. 3. 3. the squelch type returns to the programmed analog squelch type. The PTT will be ignored if DATA is selected.5 Squelch (SQL) Settings The RF-5800M-HH supports digital squelch. NOTE Function switch must be in the FP position to use the [+PRE-] buttons. Refer to Paragraph 4. and analog noise squelch.11. Data/Voice (D/V).3 Select a Net Preset Net presets are selected by using the [+PRE-] buttons to scroll the choices.5.5. 3-23 .4 Data/Voice (D/V) Settings The Data/Voice (D/V) field can be changed to Voice (VOC). The RF-5800M-HH can transmit EIA-standard Continuous Tone Coded Squelch System (CTCSS) tones in Frequency Modulation (FM) mode. Analog tone squelch requires that a 150 Hz tone be transmitted along with the normal radio traffic in order to break the receive radio's squelch.11. The [+PRE-] buttons are disabled when the function switch is placed in 1 .9.11. 11. the temporary changes are lost. The operator can temporarily override some parameters from their programmed value. NOTE Performing a temporary override may cause parameters of lower precedence to be overridden. The operator is not notified of these additional overrides. RAM is capacitor-backed for a short period after the main battery is removed. These changes are only valid until the operator selects another net. A charged battery must be reinstalled within a short period to avoid losing programming data. The radio is programmed either from the keypad or by loading a programming plan from VHF-UHF Radio Programming Application (RPA) software. This is to ensure that all radio parameters are consistent and work with one another. The operator must select the SAVE command from the OPT menu in order to save the temporary overrides as programmed values. 3-24 .3. Programmed parameters are stored in non-volatile Random Access Memory (RAM) until they are zeroized via user command. See Figure 3-9. NOTE Saving temporarily overridden net parameters without coordinating those net changes with the other net members can compromise net and radio performance. Once this occurs.6 Radio Programming Versus Temporary Overrides It is important to understand the differences between programming and temporary overrides. then press [ENT]. keypad lock. then press [ENT]. select NETS. then press [ENT]. Zeroizing clears all or a specific part of radio programming and returns the radio configuration to the factory default.Deletes only the last sent message. then press [ENT]. then press [ENT]. then press [ENT]. press the ZERO button. press the ZERO button. press the ZERO button. For 20 m models. zeroize all may also be accomplished by placing the function knob in the Z-ALL position and then using the up/down arrows to select YES. or if transmitting. press the ZERO button. LAST SENT . select TRANSEC. • To zeroize the entire radio. Use the up/down arrow buttons to select YES. then press [ENT]. • To zeroize the radio's encryption programming. • To zeroize the radio's net programming. Use the up/down arrow buttons to select YES. 3-25 . then press [ENT]. NOTE For 2 m models. zeroize all may also be accomplished by placing the function knob in the Z-ALL position and momentarily moving the toggle switch to the Z position. • To zeroize the radio's frequency hopping programming. select COMSEC. except in radio lock. select SMS. The ZERO button is always enabled. select ALL. • To zeroize the radio's Short Messaging Service information. then choose between the following: • • ALL SMS .12 ZERO OPERATION See Figure 3-8. press the ZERO button.Deletes all SMS messages.3. Use the up/down arrow buttons to select YES. Use the up/down arrow buttons to select YES. press the [ZERO] button. then press [ENT].Deletes all received messages. press the [ZERO] button. then press [ENT]. Press [ENT]. Use the up/down arrow buttons to select YES. • To zeroize the radio's network settings.Deletes all canned messages. then press [ENT]. MNO 5ZERO ALL NETS NETWORK COMSEC ALL SMS SMS LAST SENT TRANSEC RECEIVED ALERTS CANNED F-0234-4200-0008 Figure 3-8. Use the up/down arrow buttons to select YES. then press [ENT]. CANNED . • To zeroize all received Falcon Watch™ alert messages and settings. then press [ENT]. Zero Menu 3-26 . select NETWORK. select ALERTS.• • RECEIVED . Use the up/down arrow buttons to select YES. 3. 3.13 RADIO OPTIONS Figure 3-9 shows the RF-5800M-HH options menu tree. 2. STU 7OPT SAVE NET ## SAVED COMSEC CAM CAM LABEL TEK SPKR SPEAKER ENABLE ON OFF GPS RADIO SELF ID VIEW MINERR SMS ST TO BROWSE REC’D MSGS SELECT NEW ENCRYPTION KEY CRYPTO MODE RADIO REPORT POWER TRANSMIT POWER HIGH MEDIUM LOW DELETE_ALL (NOTE 3) LOCKSETS ALERTS ST TO BROWSE REC’D MSGS SELECT LOCKSET: ##/## ###. ONLY VISIBLE WHEN GPS IS CONNECTED. RF-5800M-HH Options Menu Tree 3-27 .7.####-###. Refer to Paragraph 4. USER_ENTRY F-0234-4200-0011 Figure 3-9. ONLY USED WITH DIRECTED CALLING AND WIRELESS IP NETS.##### (NOTE 1) DISPLAY ALL DELETE_ALL (NOTE 3) (NOTE 2) RESYNC HQTOD NOTES: GPS_SYNC 1. REFER TO PARAGRAPH B.3 for the complete programming menu tree. The following paragraphs describe the radio options menus. ONLY VISIBLE WHEN USING A FREQUENCY HOPPING NET. then select SAVE and press [ENT]. press the [OPT] button. CAM allows the user to add an additional layer of COMSEC encryption and is not programmable from the RF-5800M-HH radio. then press [ENT]. When using MINERR.3 Speaker (SPKR) To toggle the radio speaker on or off. • RESYNC . but can power on and start receiving in mid-transmission.13. The radio does not have to hear the start of the waveform. For more information on net programming. Valid mode options are: • MINERR . For TEK. 3.2.5.2 COMSEC To view the Communications Security (COMSEC) setting for the active net. then select SPKR. enter the encryption key and then the Crypto Mode. RESYNC is more susceptible to noise than MINERR. the start of the transmission must be heard to receive an encrypted transmission. select COMSEC. 3-28 . CAM encryption is part of the initial programming process and is loaded at the same time the radio plan is loaded.3. press the [OPT] button.13. refer to Paragraph 4.This mode allows a radio on simple voice/data nets (not directed calling or wireless IP nets) to receive an encrypted transmission already in progress. and Wireless IP. Directed Calling.13. press the [OPT] button. 3. This mode is supported across all net types: Simple. The user next enters the Traffic Encryption Key (TEK) and the Citadel Algorithm Modification (CAM).1 SAVE To save changes made from net preset displays. Use the up/down arrows to select ON or OFF.This is the default mode. There is a crypto sync that precedes the waveform. 4 GPS To view the status of an internal or externally-connected GPS.5. or LOW transmit power. Select the desired power level. MEDIUM power is 2 watts.4.13.2 for information on how to program the power level for a net preset. Refer to Paragraph 4. press the [OPT] button. heading and velocity. refer to Paragraph B. 3.13. then select POWER. and LOW power is 0. and to view. MEDIUM. For detailed information about Short Messaging Service.5 RADIO To view the Radio SELF ID (used for Directed Calling). 3. HIGH power is 5 watts. forward and delete received text messages.3 for information about Directed Calling. select GPS. reply.6 SMS This menu allows the user to create and send new text messages. Refer to Paragraph B. 3. 3-29 .13.25 watt. press the [OPT] button. press the [OPT] button. MEDIUM power is 2 watts. and LOW power is 1 watt.13. Press the up/down arrow on each page to select status of the current radio or any radio reporting its position (refer to Paragraph B. Press the circular arrow key to switch between the satellite status.3. then select VIEW. For Amplitude Modulation (AM). then select RADIO. and altitude pages. or it can be set manually. then press [ENT].6.7 POWER The transmit power level can be programmed for each net preset. HIGH power is 5 watts. For FM. To manually select either HIGH.4 for information on position reporting). 3. NOTE LOCKSETS data is only available when the active net is a frequency hopping net. then press [ENT]. For detailed information about Falcon Watch™ Sensor Alerts. For more information about locksets.4.5. refer to Paragraph B. Reset the filtering (Display All) for any Sensor Nodes that were previously filtered (Ignored). press the [OPT] button. Delete all stored Alert messages.13.9 HQTOD This menu allows the user to: • • Set the Time-Of-Day (TOD) manually.7.8 ALERTS This menu allows the user to: • • • View stored Alert messages from the optional Falcon Watch™ Sensor Alarm System. Set the TOD using Global Positioning System (GPS) and perform a GPS sync.13.1. LOCKSETS will not display on a fixed frequency net.13.3. To view the frequency hopping lockset information for the active net. select LOCKSETS. 3. refer to Paragraph 4. 3-30 .10 LOCKSETS (Hopping Only) A lockset specifies frequencies that cannot be used during list or wideband frequency hopping. This list is separate from the list of net presets that are activated in the list (for use with the +PRE. Use the [CLR] button to toggle between the two. but some calls may be missed. If a signal is present on a net. Reliable operation in CT requires two procedural modifications because of the preamble synchronization required by encrypted transmissions. First.1). the radio stops scanning and holds on that net for the programmed hold time. The maximum number of nets that can be reliably scanned depends upon whether the radio is in PT or CT. There are two ways to scan: automatic and manual. If signal 3-31 . This extends the transmitters preamble to give the scanning radio enough time to synchronize after it scans all other nets in the scan list. If no hold time is specified.8. the radio remains on that net until signal presence is lost or the user presses [CLR] to continue automatic scan. In automatic scan. the number of nets in a CT scan list should be no more than five with a sixth Receive (RX) Priority Net.button). 3. A full 25-net scan list can be used in PT. the radio scans each net in the list for the presence of an RF signal. The radio will search fixed frequency net presets for the presence of a Radio Frequency (RF) signal. NOTE Net Scanning is not available in frequency hopping modes. The user can program a list of up to 25 net presets into the scan list.14 NET SCANNING The RF-5800M-HH can be set for scan operation by placing the function switch in SCAN position.NOTE Locksets that have been programmed into the radio apply to all frequency hopping nets. It is possible to scan more nets in CT. the calling radio should have Robust Preamble turned on (refer to Paragraph 4. Second. . Pressing the PTT button while the radio is stopped on a net will cause the radio to transmit on that net. press the [CLR] button. For more information on hang time and hold time. the radio waits the programmed hang time before continuing to automatically scan.2. the radio is in manual scan. press the [CLR] button. SCAN will initiate automatically. or has stopped because the operator has pressed the [CLR] button).2 for more information. For more information on the transmit priority net. 3-32 b.15. c. To switch to manual scan. refer to Paragraph 4.6. Turn the function switch to the SCAN position. During manual scan. Refer to Paragraph 3. To enter automatic scan. NOTE Beacon mode is disabled during Scan operation. NOTE Pressing the PTT button while the radio is scanning causes the radio to transmit using the transmit priority net. refer to Paragraph 4.presence is lost during the hold time. When not automatically scanning (the radio has stopped on a net that has an RF signal. d. If SCAN is enabled. use the [+PRE-] button to manually scroll through the scan list. To return to automatic scan.1.6. perform the following procedure: a.2. turn the Mode Switch to a position other than SCAN. See Figure 3-10. pressing the circular arrow button switches between the scan displays. The scan displays provide information similar to the normal net preset displays. See Figure 3-10. 3-33 . To exit scanning.NOTE When the radio is not scanning because the [CLR] button has been pressed or signal presence is detected. e. SCAN R BAT AUTOMATIC SCAN DISPLAY PT SCANNING PRESS CLR FOR MANUAL SCAN CLR OR SIGNAL PRESENCE IS DETECTED OR RADIO IS KEYED SCAN R BAT MANUAL SCAN DISPLAY NET4 VOC PT CLEAR D/V S3 6 TONE FM MOD VOICE 9+ SQL 0 R BAT MANUAL SCAN DISPLAY SCAN PT R: 225.00000 FIX NONE FREQUENCY RATE Figure 3-10. SCAN Displays 3-34 S3 6 9+ F-0234-4200-0012 .00000 T: 225. 3.15 OPERATIONAL MODE MENU Figure 3-11 shows the RF-5800M-HH MODE menu tree. The following paragraphs describe the radio MODE menus. GHI 3MODE OPERATIONAL MODE REMOTE CONTROL (NOTE 1) OFF ON BEACON OFF ON RETRANSMIT OFF ON-SYNC ON-ASYNC CLONE CLONING FREQUENCY (###.##### MHz) ENCRYPTION KEY (#####) CLONE TYPE RECEIVE NOTES: 1. ONLY APPEARS IF REMOTE CONTROL IS ENABLED. 2. TEST MENU IS SHOWN SEPARATELY IN PARAGRAPH 3.7. TRANSMIT KEYPAD LOCK RADIO LOCK TEST (NOTE 2) VAA OFF ON F-0234-4200-0007A Figure 3-11. RF-5800M-HH Mode Menu 3-35 3.15.1 Remote Control Remote control is only available when using a remote terminal or PC. Remote control can only be enabled from the remote terminal or PC, not from the [MODE] button. Once enabled, remote control can be disabled using the [MODE] button. See Figure 3-11. NOTE If remote control and keypad lock are both enabled, remote control should be turned off before turning off keypad lock. 3.15.2 Beacon Mode Placing the RF-5800M-HH in Beacon mode makes the radio transmit on a selected frequency by sending either a constant tone or a user-selectable swept tone audio. The beacon can transmit on any frequency in the full range of the radio (30 MHz to 512 MHz). Beacon mode frequency, tone type, power level, and duty cycle can be adjusted from the PGM>CFIG>BEACON menu. Refer to Paragraph 4.8.2 for beacon configuration information. See Figure 3-11 and perform the following procedure to activate the beacon: 3-36 a. Press the [MODE] button. b. At the OPERATIONAL MODE prompt, use the up/down arrow buttons to select BEACON, and press [ENT]. c. At the BEACON MODE prompt, select ON and press [ENT]. d. The radio will begin transmitting on the configured beacon frequency and duty cycle. The beacon transmission is a repetitive cycle for both swept tone and tone settings. NOTE Normal radio net transmission will override the beacon transmission. If the radio is keyed while in Beacon Mode, the beacon transmission will be stopped until the radio is unkeyed. NOTE Beacon mode is disabled during Scan operation. To exit Beacon mode: 3.15.3 a. Press the [MODE] button. b. At the OPERATIONAL MODE prompt, use the up/down arrow buttons to select BEACON, and press [ENT]. c. At the BEACON MODE prompt, use the up/down arrow buttons to select OFF, and press [ENT]. Retransmit Mode A retransmission or repeater station receives a signal transmitted on one frequency and retransmits that signal on another frequency (on another radio), enabling communication over a greater range than is possible using individual radios. A retransmission or repeater station for extending communication range can be set up using two radios. Two types of operation are available using the retransmit setup: • • Black Digital Retransmit operation - Paragraph 3.15.3.1 Red Analog Retransmit operation - Figure 3.15.3.2 3-37 The retransmit site radios are operated in PT and just pass the encrypted digital signal through the retransmit cable. In this mode. the retrans station uses frequency F1 on one radio to transmit and receive with one group of radios. It uses frequency F2 to transmit and receive with a second group of radios. 3-38 . F1 and F2 can be any LOS fixed frequency or frequency hopping net preset. The retrans station consists of two radios connected by a retrans cable.Both types of operation use the same equipment and setup. The only difference in operation is how the retransmission/repeater station is used by other radios.15. all stations except the two retransmit site radios operate in CT with the same COMSEC mode and key. The most common operation and preferred method is to operate the retransmit site in black digital retransmit mode. while the retransmit site radios are operated in PT and simply pass the already encrypted digital signal through the retransmit cable. avoid contact with antennas in retransmit mode operation as each radio transmits automatically in response to incoming calls on the opposite retrans radio. all outstations operate in CT with the same COMSEC mode and key. Signals received on F2 are retransmitted on F1. The retransmission operation can be summarized as follows: • • Signals received on F1 are retransmitted on F2. WARNING To prevent electrical shock and RF burns. In the black digital retransmit scenario. 3. Here.1 Black Digital Retransmit Operation Figure 3-12 shows Black Digital retransmit operation.3. RETRANSMIT STATION F1 F2 PT PT RADIOS USING F1 (RX/TX) COMMUNICATE THROUGH RETRANSMISSION STATION WITH RADIOS USING F2 (RX/TX) ELEVATION F1 F1 F2 F2 CT CT F-0234-4200-0013 Figure 3-12. Black Digital Retransmission Operation 3-39 . The retransmit station uses frequency F1 on one radio to transmit and receive with one group of radios. All radios are operated in CT and must be secured. F1 and F2 can be any LOS fixed frequency or frequency hopping net preset.15. In Red Analog operation. 3-40 . Digital Squelch is used to disable PT override (if necessary).3. Signals received on F2 are retransmitted on F1.3.2 Red Analog Retransmit Operation Figure 3-13 shows Red Analog retransmit operation. It uses frequency F2 to transmit and receive with a second group of radios. The retransmit station consists of two radios connected by a retransmit cable. and each net has its own COMSEC key and operating type. all stations operate in CT mode. The retransmission operation can be summarized as follows: • • • Signals received on F1 are retransmitted on F2. RETRANS STATION F1 F2 CT CT ELEVATION F1 F1 F2 CT F2 CT F-0234-4200-20 Figure 3-13. Red Analog Retransmission Operation 3-41 . Using this arrangement. The repeater receives on frequency F1 and transmits on frequency F2. 3-42 . all outstation radios transmit on F1 and receive on F2. All outstation radios that use the repeater station for retransmission operate half-duplex nets.15. where the same frequency serves for both transmitting and receiving.3 Repeater Retransmission Operation Repeater operation is used when a net wants to gain extended range. The repeater station uses simplex operation using separate transmit and receive frequencies. Figure 3-14 shows repeater operation.3.3. all units must communicate with each other through the repeater. With this setup. REPEATER STATION F1 RCV F2 TX ALL RADIOS COMMUNICATE THROUGH THE REPEATER F1 F2 ALL RADIOS: TX-F1 RCV-F2 ELEVATION 117F-011A Figure 3-14. Repeater Operation 3-43 . Figure 3-15 shows the retransmission/repeater hardware configuration. F1 and F2 should not be within 20% of each other.15. Separate the radio units by fully extending the retransmit cable to prevent receiver desensitization and RF interference between units. For optimum performance.5 Frequency Separation For simplex operation.3. the repeater site should be elevated above the level of the outstations. For best retransmission performance.4 Hardware for Retransmission/Repeater Setup The following equipment is used for retransmission/repeater operation: • • Two RF-5800M-HHs with antennas and battery packs Retransmit cable (12011-0230-A050) NOTE When using Retransmit mode.3.15. locking the keypad of the radio will blank the radio’s display.3.for example: 60 MHz is the “first order” harmonic of 30 MHz). ensure the retransmit cable is in contact with the ground along most of its length. 3. Connect the retransmit cable to the side connector on each radio. and should not be harmonically related (when one frequency is a whole number multiple of the second . 3-44 . Retransmission/Repeater Hardware Setup 3-45 .) SIDE CONNECTOR SIDE CONNECTOR RETRANSMIT CABLE (12011-0230-A050) F-0234-4200-0015 Figure 3-15.RECOMMENDED FREQUENCY SEPARATION: > 20% (NOT HARMONICALLY RELATED) F1 F2 RECOMMENDED SEPARATION DISTANCE: FULL CABLE LENGTH (50 FT. NOTE To determine the radio’s firmware version.6 Retransmit Settings Determine whether Black Digital or Red Analog operation is required. Perform the following procedure to configure the RF-5800M-HH: a. Turn on each RF-5800M-HH to CT position for red analog operation.3. d. Use the up/down arrow keys to select ON-SYNC or ON-ASYNC and press [ENT]. Turn radio switch to OFF.0. e. The Robust Preamble setting (refer to Paragraph 4. Use the up/down arrow keys to select RETRANSMIT and press [ENT]. Press the [MODE] button.0 or later. 3-46 . • • ON-SYNC is used for backward compatibility with radio firmware prior to version 6.15. Attach the retransmit cable to the side connector on both radios. f. c.8. b. Set the retransmit radios to the net preset that will be used for retransmission. Turn on each RF-5800M-HH to PT position for black digital operation. press the [MODE] button then >TEST> VERSION>FIRMWARE.1) should be set to ON when the RF-5800M-HH is being used in Retransmission/Repeater operation.3. ON-ASYNC is used for radios with firmware version 6. g. 15. All clone data is transferred at LOW power in CT mode (encrypted) regardless of the power setting and the PT/CT selection. Clone Mode The RF-5800M-HH is able to transfer most configuration parameters to identical handheld radios within a distance of 20 feet (6 meters) using wireless cloning.1 Receiving Wireless Cloning Information NOTE When performing the following procedure. The transferred data does not include backlight or volume settings. The transferred data includes COMSEC keys. 3.NOTE Black frequency hopping is supported using RETRANSMIT>ON-ASYNC mode only.15. TRANSEC parameters. The process requires one radio to be set to transmit programming parameters. 3. and the other radios set to receive them. Digital squelch must be used in each of the retransmit radios to prevent falsing condition where one radio is locked in transmit condition. and CONFIGURATION settings except for Wireless Internet (WIP) or Directed Call Nets.4. 3-47 . If one radio locks into continuous transmit. h. ensure that the radios are no more than 20 feet (6 meters) apart. NET PRESETS. See Figure 3-11.4 Begin retransmission operations. This is the maximum separation distance allowed. check for presence of interfering signals on the receiving radio and/or check squelch settings to determine if squelch falsing condition exists. display changes to RECEIVE COMPLETE ANY KEY TO EXIT. c. A progress meter is shown on the next display line. NOTE Press [CLR] to abort setting up a radio for cloning receive operation. This key is used to encrypt the cloning data. g. The radio displays AWAITING RECEIVE. Press the [MODE] button.Any number of receive radios can be configured to accept cloning information. This must match the frequency used by the transmitting source radio. Enter a six-digit numeric encryption key and press [ENT]. NOTE This key is NOT the Traffic Encryption Key. This defaults to the current radio frequency. This is only used for the cloning process. Display changes to RECEIVING as information is received. Perform the following procedure to set up a radio for cloning receive operation: a. The encryption key must match the key used by the transmitting source radio. d. e. On successful receipt of information. Select RECEIVE and press [ENT]. 3-48 f. Progress meter increases to 100%. Select CLONE and press [ENT]. . b. Enter the desired frequency and press [ENT]. Enter a six-digit numeric encryption key and press [ENT]. Software version failure . d.4. NOTE Press [CLR] to abort clone transmission. Press the [MODE] button. 2.15. All target radios must display AWAITING RECEIVE before cloning information is transmitted. Receive failure . b.4. This defaults to the current radio frequency.attempting to clone between dissimilar software versions: VERSION MISMATCH ANY KEY TO EXIT. This key is used to encrypt the cloning data. This must match the frequency used by the target receiving radio(s).attempting to clone between dissimilar radios. Enter the desired frequency and press [ENT]. Refer to Paragraph 3.15. Select TRANSMIT and press [ENT]. Wrong radio type .: INVALID RADIO TYPES ANY KEY TO EXIT.h. wrong encryption key: RECEIVE FAILURE ANY KEY TO EXIT. Transmitting Wireless Cloning Information Verify that all target radios have been prepared to receive the cloning information. any of the following error messages may be seen: 1. 3. 3-49 .data integrity failure. 3. The encryption key must match the key used by the target receiving radio(s).2 If information is not successfully received. Select CLONE and press [ENT]. c. Perform the following procedure to set up the source radio for cloning transmit operation: a.1. 15.15.15.6 Radio Lock Refer to Paragraph 3. On successful transmission of information.15. Turn on the R/Ts and perform communications checks to verify accurate cloning. A progress meter is shown on the next display line.5. 3. 3-50 . The progress meter increases to 100%. 3. 3.4. f.15.e.7. Set the VAA MODE to OFF if the RF-5800M-HH will be operated only as a standalone handheld radio. The radio displays TRANSMITTING. See Figure 3-11 for menu tree selections. display changes to TRANSMIT COMPLETE ANY KEY TO EXIT. and subsequently operate the RF-5800M-HH as a standalone handheld radio. 3. 3. This feature allows the user to disconnect the radio from the VAA without cycling power.6.1 for complete procedures.1 for complete procedures.5 Keypad Lock Refer to Paragraph 3.7 Test Mode Refer to Paragraph 3. The radio may also be re-connected to the VAA with power on. Setting VAA MODE to ON will enable the radio for “Jerk and Run” operation.8 VAA Mode VAA Mode is used when an RF-5800M-HH is to be installed in the optional RF-5800M-V520 Vehicular Adapter Amplifier or RF-5800V-V500 Vehicular Adapter Amplifier.2 for complete procedures. turn off each Receiver-Transmitter (R/T).3 Verifying The Status Of A Wireless Cloning Transfer After the completion of a wireless cloning data transfer. If using the VHF-UHF RPA to program the radio.3 4-1 .5.Paragraph 4.Paragraph 4.4 Program encryption keys .2 Program frequency hopping nets .CHAPTER 4 RADIO PROGRAMMING NOTE Performing programming functions places the RF-5800MHH in an offline state.2. or directly from the radio front panel keypad.5.Paragraph 4.5.Paragraph 4. proceed to Paragraph 4.2 Program hopsets .1. are performed in the following order: • • • • • • Program security (access level) settings . 4.5.2.1.1 PROGRAMMING TASK SUMMARY The RF-5800M-HH can be programmed either from a Personal Computer (PC) using the Very High Frequency (VHF)-Ultra High Frequency (UHF) Radio Programming Application (RPA) software. in general. Front panel programming tasks.5.4 Program fixed frequency nets . Radio communications are not possible while the radio is being programmed.1.3 Program locksets .Paragraph 4.Paragraph 4.2 for setup information and use the remainder of this chapter for reference only. d. .Paragraph 4. Situational Awareness. and Falcon Watch™ Sensor Alerts.• • • • Program net scanning . c. or FP.5.8 Program advanced features as needed . b. The Remote Control/Programming Cable Assembly part number (12011-0200-A006) is used to make the connection. Perform the following procedure to attach a PC to the radio: 4-2 a. Short Messaging Service (SMS). Follow the procedure in Paragraph 4.Paragraph 4. RF-6010 Basestation support.6 Program port parameters .7 Program other configuration items .2 ATTACHING A PC TO RADIO FOR VHF-UHF RPA PROGRAMMING The RF-6550V VHF-UHF Radio Programming Application (RPA) (supplied separately) can be used to ensure programming consistency and faster programming of multiple radio units. Wireless IP Network.Appendix B NOTE Advanced features covered in Appendix B include Directed Calling. Follow the procedures in Appendix B to set other advanced network parameters that may be required. 4. Rotate function switch to 1 .1 to configure the remote port to match the serial port of the PC. The RPA interfaces with a personal computer using the serial port on the Ancillary (ANC) side connector of the radio.7. Power the RF-5800M-HH OFF.Paragraph 4. Refer to Paragraph 4.1 for more information on ANC. The RF-5800M-HH is now ready to be programmed by the PC using the Harris VHF-UHF RPA. 4-3 . h.4. f. or position 1 . Function switch should be in FP. When programming is complete.5 (per Step a). Refer to the RF-6550V VHF-UHF RPA Software User’s Guide (10515-0318-4200) for more information about the RPA program. PROGRAMMING MENU TREE See Figure 4-1 for a menu tree of all the RF-5800M-HH programming menus. turn remote mode off. Connect the other end of the cable to the appropriate serial port on the PC. g.8.3 e. Make sure ANC is enabled on the radio. Connect (12011-0200-A006) cable to the ANC side connector of the RF-5800M-HH. VWX 8PGM TO SHEET 4 NORM TO SHEET 3 NET D C SELECT NET TO MODIFY ## NET NAME ACTIVATE IN LIST? YES NO NET TYPE FIXED FREQUENCY COMSEC FREQ RECEIVE FREQUENCY ###. Figure 4-1.##### MHz DATA/VOC SQUELCH POWER NAME TRANSMIT POWER ENCRYPTION KEY TEK ## CHANGE NAME HIGH XXXXXXXXXXXX MEDIUM CRYPTO MODE MINERR. ONE OF THE RECOMMENDED SETTINGS WILL BE DISPLAYED.##### MHz TRANSMIT FREQUENCY ###. RESYNC LOW CHANGE FM DEVIATION* NO YES RECEIVE ONLY NO YES FREQUENCY HOPPING HOPPING TYPE TO SHEET 2 TO SHEET 2 COMSEC HOPSET RECEIVE HOPSET ## (R###) DATA/VOC POWER TRANSMIT POWER TEK ## HIGH RECEIVE ONLY A NAME ENCRYPTION KEY TRANSMIT HOPSET ## (T###) B CHANGE NAME XXXXXXXXXXXX MEDIUM LOW NO TO SHEET 2 A YES *IF THE DEVIATION SET IS NOT A RECOMMEMNDED SETTING FOR THE CURRENT FREQUENCY. RF-5800M-HH Programming Menu Tree (Sheet 1 of 6) 4-4 F-0234-4200-0016-1A . BAUD RATE (NOTE 2) 16. 8000 F-0234-4200-0016-2A Figure 4-1.FROM SHEET 1 FROM SHEET 1 A B DIGITAL SQUELCH DATA/VOICE VOICE OFF DATA OR VOICE (D/V) ON DATA ANALOG SQUELCH D/V TYPE SELECT TONE SIMPLE WIRELESS IP (REFER TO APPENDIX B.3. ONLY AVAILABLE WHEN DATA/VOC IS SET TO DATA. RF-5800M-HH Programming Menu Tree (Sheet 2 of 6) 4-5 . 1600.0 kHz CTCSS (NOTE 2) NOTES: 1.0 K. ON CTCSS TONE ONLY AVAILABLE WHEN D/V TYPE IS SET TO SIMPLE.) DIRECTED (REFER TO APPENDIX B.5 kHz 5.) NOISE OFF VOICE MODE (NOTE 3) NONE CVSD MODULATION (ONLY AVAILABLE IN SIMPLE NET) FM AM WBFSK ASK FM DEVIATION (ONLY AVAILABLE IN FM NET) 8. NOT AVAILABLE WHEN DATA/VOC TYPE IS SET TO SIMPLE. 2666. OFF 2.0 kHz 6. 3.5. ##### MHz *****LOCKSET ***** ****DELETED**** COPY DELETE REVIEW HOPSET IN COMPARTMENT ## LOCKSET ##/## ###.##### WIDEBAND (WIDEBAND) ENTER HOPSET ID F### DELETE HOPSET IN COMPARTMENT ## ******HOPSET ******* ******DELETED****** LOCKSET ##/## ###. ##### MHz *****FREQUENCY ***** *******ADDED****** ENC KEY ID ## F-0234-4200-0016-3B .##### (LIST) OR HOPSET ## HOPSET TYPE ###. RF-5800M-HH Programming Menu Tree (Sheet 3 of 6) 4-6 KEY NAME: KEY: ############### HOPSET COMPARTMENT COPY FROM ## ENTER START FREQ ###. LIST ADD REVIEW DELETE FREQUENCY TO ADD ###. ###. ###.##### . ##### MHz FREQUENCY ## OF ## ###.#####-###. ##### MHz **KEY TYPE ONLY VISIBLE WHEN CITADEL II IS ENABLED.##### MHz *****FREQUENCY ***** *******DELETED****** Figure 4-1.###.#####-###.##### MHz ENTER STOP FREQ.C FROM SHEET 1 GENERAL HOPPING NAME RADIO NAME ################### HOPPING TYPE ENCKEY LOCKSET HOPSET DEFINE REVIEW ADD ENTER START FREQ.##### DELETE KEY TYPE:** REVIEW NAME: TYPE: HOPSET COMPARTMENT COPY TO ## DELETE NAME: TYPE: DELETE KEY ## COPY AS HOPSET ID F### NO YES ENTER STOP FREQ ###. #####MHz FREQUENCY ## OF ## ###.##### MHz DEFINE SET HOPSET IN COMPARTENT ## REVIEW FREQUENCY ## OF ## ###. NET MUST BE SIMPLE FIXED FREQUENCY.D FROM SHEET 1 TO SHEET 5 SCAN LIST PRIORITY ADD NET TO ADD ## [NET NAME] (REFER TO NOTE 4) REVIEW NET TO REVIEW ## [NET NAME] PRIORITY TX NET ## NET NAME ENABLE RX PRIORITY SCANNING? YES PRIORITY RX NET ## NET NAME NO E CONFIG HANG TIME ## SECONDS ENABLE HOLD TIME? YES HOLD TIME ## SECONDS NO DELETE NET TO DELETE ## [NET NAME] NOTES: 4. RF-5800M-HH Programming Menu Tree (Sheet 4 of 6) 4-7 . F-0234-4200-0016-4A Figure 4-1. ONLY VISIBLE WHEN SECURITY LEVEL IS GREATER THAN 1-TECHNICIAN.E FROM SHEET4 PORTS SECUR DATA REMOTE ASYNC RATE 115.) F BYPASS SECURITY ACCESS BYPASS ENABLE EXTERNAL DATA CLOCK POLARITY NORMAL INVERTED 300 150 75 DATA BITS 8 7 STOP BITS 1 2 PARITY NONE ODD EVEN FLOW CONTROL NONE NOTES: 5.) PASSWORD SECURITY LEVEL 3-RADIO TEST 2-DEPOT 1-TECHNICIAN 0-OPERATOR (REFER TO NOTE 5.2 K 9600 4800 2400 1200 600 LEVEL DATA PORT TYPE SECURITY LEVEL 3-RADIO TEST 2-DEPOT SYNC 1-TECHNICIAN TX DATA CLOCK SOURCE 0-OPERATOR INTERNAL TO SHEET 6 (REFER TO NOTE 6.4 K 19. 6.6 K 38. PASSWORD SECURITY LEVEL CHOICES ARE DEPENDENT ON THE SECURITY LEVEL CHOSEN UNDER THE LEVEL MENU.2 K 57. RF-5800M-HH Programming Menu Tree (Sheet 5 of 6) 4-8 F-0234-4200-0016-5A . XON/XOFF ASYNC ECHO ON OFF Figure 4-1. 3200 Hz) BEACON FREQ (30 .3200 Hz) SWEEP RATE (1 . HIGH) OFF TIME (0 .7) DC ANTENNA BIAS OFF ON UHF RECEIVE PATH LNA BYPASS F-0234-4200-0016-6D Figure 4-1. THIS MENU OPTION WILL APPEAR. MED. RF-5800M-HH Programming Menu Tree (Sheet 6 of 6) 4-9 .100 SECONDS) ON TIME (1 .F FROM SHEET5 CFIG GENERAL GPS SMS FM TRANSMIT TONE (REFER TO (REFER TO ON APPENDIX B.6) OFF SILENCE BEEPS? NO YES ROBUST PREAMBLE ON OFF POWER MANAGEMENT ON OFF ANC CONNECTOR DISABLE ENABLE CLCK NETWORK BEACON BEACON TYPE (REFER TO SWEPT APPENDIX B.4) APPENDIX B.100 SECONDS) UTC OFFSET ±00:00 DATE FORMAT MM-DD-YY ZULU NEW DATE/TIME YYYY-MM-DD DD-MM-YY TONE TONE FREQ (300 .5.10 Hz) BEACON FREQUENCY (30 . EXT_DEV EXTERNAL 50 W PA MODE CO-SITE ON CO-SITE OFF BYPASSED ALERTS (REFER TO APPENDIX B.3200 Hz) STOP FREQ (300 .100 SECONDS) NEW DATE/TIME #### ## #### NEW TOD ##: ##: ## NOTE: IF ANY OTHER DATE FORMAT OTHER THAN ZULU IS SELECTED. MED. HIGH) OFF TIME (0 .100 SECONDS) ON TIME (1 .512 MHz) BEACON POWER LEVEL (LOW.512 MHz) BEACON POWER LEVEL (LOW.) START FREQ (300 . DEPOT . the technician can program radio nets. these changes cannot be saved. A radio operator can change radio nets.is to be used at the depot level and only adds the ability to BYPASS security access. Press the [PGM] button.4. run BITE. Refer to Paragraph 4. voice mode. This allows for low level radio troubleshooting commands to be run.RADIO TEST . At this level.4 SECURITY MENU (SECUR) The RF-5800M-HH provides four levels of security access: • 0 . and override net parameters.is the default security level for basic radio operators.3 for security access BYPASS information. save overridden net parameters.TECHNICIAN .4.is for radio technicians. Select LEVEL and press [ENT]. b. • 2 . • 1 . and change data and remote port settings. The radio net parameters will revert back to the programmed settings once the operator changes to a different net. program scan list.OPERATOR . enter scan mode. . • 3 . and frequency.4.is a radio test level.1 Level Access To program the radio's security access level: 4-10 a. 4. Although the operator can override parameters such as power level. and press [ENT]. load keys. then the left/right arrow buttons to select SECUR. and press [ENT]. b. The default password for 2 . then select PASSWORD. The 0 . 2. followed by [ENT].Radio Test 0.2 Password Programming To change the security access level passwords: a. 1.Operator is no entry. 4. a password is required.4.2.Technician 0. For information on changing passwords.Operator password is used to unlock the keypad at all security levels. NOTE When shipped from Harris Corporation. If a level higher than the current level is selected.Depot 0. 1 2 . select SECUR. The default password for 1 .c. the first page of this document contains Security Level 3 password information. Identify the security level. a user can change their own level and all lower levels per the following: Level Password Levels That Can be Changed 0 .4. Press the [PGM] button. 1.TECHNICIAN is HH1. 2 3 . Press the up/down arrow buttons to select the desired security level. then use the alphanumeric keypad to enter a new password. it may have been removed by a Communications Security Monitor.Operator 0 1 . If this page is missing.DEPOT is HH2. The default password for 0 . 3 4-11 . NOTE At each security level. refer to Paragraph 4. then change SECURITY ACCESS from ENABLE to BYPASS. refer to Paragraph 4.1.RADIO TEST. 4.3 BYPASS Programming 2 . Two choices are available: GENERAL and NET. See Figure 4-1. hopsets.5.1. Zeroizing the radio does not return modified Security Level 1 or Security Level 2 passwords back to the default passwords. press the [PGM] button. except for those at 3 . For information on NAME programming. refer to Paragraph 4.DEPOT and 3 .1.3.5.5. password. For information on ENCKEY programming.5. The Security Level 3 password can be changed.4. select SECUR. For information on LOCKSET programming. encryption keys. and locksets.A Security Level 1 operator can only change the Security Level 1or 0 (zero). press [PGM]. 4-12 . all radio commands become available.1. 4.RADIO TEST users can choose to BYPASS security access for lower levels.1 GENERAL Programming GENERAL programming is used to program radio name.1. Use the left/right arrow buttons to select NORM and press [ENT]. refer to Paragraph 4. select BYPASS. A Security Level 2 or a Security Level 3 operator can change the Security Level 1 and Security Level 2 passwords.5. To BYPASS security access. For information on HOPSET programming. but will revert to the factory default when the radio is zeroized.2. 4. In BYPASS mode. refer to Paragraph 4.5 NORM MENU To perform NORM programming.4. Press [PGM]. b. Perform the following procedure to program encryption keys: a. 4-13 .2 ENCKEY Programming An encryption key is a 32-digit hexadecimal number (128-bit for Citadel I/AES-128) or a 64-digit number (256-bit for Citadel II/AES-256) that the radio's encryption software uses to enable secure Cipher Text (CT) and Advanced Encryption Standard (AES) with Citadel II communications.4.5. select NORM and press [ENT].1. select NORM and press [ENT]. e.5. From the same menu screen that includes Define. Enter a name consisting of up to 16 alphanumeric characters and press [ENT]. d. b. Use the left/right arrow buttons to select ENCKEY and press [ENT].1 NAME Programming A specific custom radio name can be assigned that is viewable on the preset screen. d. Enter ENC KEY ID (1 to 25) and press [ENT]. Press [PGM]. All radios communicating on a net must use the same encryption key.1. c. Use the left/right arrow buttons to select NAME and press [ENT]. c. Select GENERAL and press [ENT]. Use the left/right arrow buttons to select DEFINE and press [ENT]. the user can also REVIEW or DELETE existing keys. 4. Perform the following procedure to program the radio name: a. Select GENERAL and press [ENT]. Up to 25 encryption keys can be programmed. Use the left/right arrow buttons to select DEFINE and press [ENT]. From this screen. DELETE. d. 4. At the KEY prompt enter a 32-digit or 64-digit hexadecimal encryption key number and press [ENT]. Press [PGM]. NOTE A maximum of 30 frequencies can be programmed into a list hopset. A wideband hopset requires a start frequency and a stop frequency. Select HOPPING TYPE and press [ENT]. . h. Enter KEY TYPE and press [ENT]. Enter KEY NAME and press [ENT]. c.3 HOPSET Programming A hopset consists of a hopset compartment number. e. A list hopset requires a list of specific frequencies the net uses for hopping. b. g. the user can also REVIEW. or COPY existing Hopsets.1.f. Enter SET HOPSET IN COMPARTMENT number (1 to 25) and press [ENT]. a hopset identification (ID) number. Perform the following procedure to define a hopset: 4-14 a. The list must contain at least one frequency. f. g.5. Select GENERAL and press [ENT]. Use the left/right arrow buttons to select HOPSET and press [ENT]. select NORM and press [ENT]. and hopset frequency information. Select HOPPING and press [ENT]. select REVIEW. j. To copy a hopset from one hopset compartment to another compartment. 2. 1. also known as an exclusion band. The radio automatically rounds frequencies down to the nearest 25 kHz. All radios must be programmed with the same locksets.h. For wideband hopsets.1. Finally.4 LOCKSET Programming A lockset. select COPY. 4-15 . 4. l. ADD individual frequencies. b.5. enter a START FREQ and a STOP FREQ. and enter the hopset's two-digit hopset compartment number. For list hopsets. Perform the following procedure to define a lockset: a. Select GENERAL and press [ENT]. A maximum of 25 locksets can be programmed into the radio. To review a hopset. Press [PGM]. Enter HOPSET IN (a unique three-digit hopset ID) and press [ENT]. Select a HOPSET TYPE of either WIDEBAND or LIST and press [ENT]. k. and enter the compartment number copying to and hopset ID of the new hopset being created. specifies a range of frequencies that cannot be used during list or wideband frequency hopping. and enter the hopset's two-digit hopset compartment number. To delete a hopset. under LIST. select DELETE. enter the two-digit hopset compartment number of the hopset to be copied. use the DEFINE menu to modify the new hopset compartment as required. under LIST. Frequencies must be listed in the same order for all radios in a net. Programmed locksets apply to all hopsets. select NORM and press [ENT]. i. 2.1. Select HOPPING TYPE and press [ENT]. For information on FIXED FREQUENCY net programming. Use the left/right arrow buttons to select LOCKSET and press [ENT]. Select HOPPING and press [ENT].3. f.2. 4.5. Up to 25 net presets can be programmed into each radio (NET0 through NET24). . See Figure 4-1. Press [ENT]. i.1 Net Programming Considerations Nets have the following characteristics: • • • 4-16 Scan mode allows scanning of a user-defined list of fixed frequency simple net presets. e. Use the left/right arrow buttons to select ADD and press [ENT].5. g. refer to Paragraph 4.2.c. Enter a start frequency at ENTER START FREQ and press [ENT]. select DELETE and use the up/down arrow buttons to select lockset to delete. Enter a stop frequency at ENTER STOP FREQ and press [ENT].2 Net Programming NET programming is used to program net presets. refer to Paragraph 4. To delete a lockset.5. For information on FREQUENCY HOPPING net programming. j.2.5. 4. h.2. select REVIEW and use the up/down arrow buttons to scroll locksets.5. refer to Paragraph 4. A net name can consist of up to 12 alphanumeric characters. d. For net programming considerations. To review a lockset. NOTE Spaces are not allowed within the net name. The default name for each net is NET## where ## represents a number from 0 to 24. Select NET and press [ENT].5. If ACTIVATE IN LIST? is set to YES. • Each net preset may be enabled or disabled during the Activate In List menu function. f. that net is available to the operator. Select YES or NO as appropriate. 4-17 . that net is not available when the function switch is in FP.2 Fixed Frequency Net Programming Perform the following procedure to program a fixed frequency net: a. Use the left/right arrows to select FREQ and press [ENT]. Select FIXED FREQUENCY and press [ENT]. e. A disabled net is retained in memory but does not appear in the scrolling list. d. If ACTIVATE IN LIST? is set to NO.2. Enter the receive frequency and press [ENT]. then press [ENT]. Enabled net presets appear in the scrolling list controlled by the [PRE +] or [PRE -] button (when the function switch is in the FP position). b. 4. select NORM and press [ENT]. pressing the [PRE +] or [PRE -] button returns the radio to the last operational display if the function knob is in the FP position. Press [PGM]. Use the numeric buttons to enter the number of the net to be programmed. c. • While in program mode. • Changing the function knob position causes the radio to exit program mode. Use the left/right arrows to select COMSEC and press [ENT]. Enter encryption key number and press [ENT]. The radio does not have to hear the start of the waveform. There is a crypto sync that precedes the waveform. DATA.This is the default mode. Refer to Paragraph 4. so it is only necessary to change it if using a half-duplex net. choose a VOICE MODE of either NONE or CVSD and press [ENT]. Press [ENT]. RESYNC is more susceptible to noise than MINERR. Use the up/down arrows to choose SIMPLE for the D/V type and press [ENT].g. The transmit frequency is automatically set to match the receive frequency. This mode is supported across all net types: Simple. If DATA was previously selected. set RECEIVE ONLY to YES.5. refer to Appendix B. l. h. Select a crypto mode of either MINERR or RESYNC and press [ENT]. m. Directed Calling.This mode allows a radio on simple voice/data nets (not directed calling or wireless IP nets) to receive an encrypted transmission already in progress. If the radio is to be in radio silence on the net. Amplitude Modulation (AM). When using MINERR. and Amplitude Shift Keying (ASK). and Wireless IP. the start of the transmission must be heard to receive an encrypted transmission. Available choices are dependant upon which DATA/VOC was selected. Enter the transmit frequency and press [ENT]. If the radio is to be able to transmit on the net. or DATA OR VOICE (D/V) and press [ENT]. Use the up/down arrows to choose a MODULATION type: Frequency Modulation (FM). • MINERR . • RESYNC . 4-18 . Use the left/right arrows to select DATA/VOC and press [ENT]. If Directed Calling or Wireless IP operation are to be used. j. set RECEIVE ONLY to NO.2 for information on programming encryption keys. i. k. but can power on and start receiving in mid-transmission. Press [ENT].1. Wideband Frequency Shift Keying (WBFSK). Use the up/down arrows to select VOICE. Refer to Table 3-2 for DATA/VOC capabilities of each modulation type. Refer to Paragraph 4. MEDIUM. up to 12 characters long. Use the left/right arrows to select ANALOG SQUELCH TYPE of TONE. Select NET and press [ENT]. d.n. 6. Press [PGM]. then press [ENT]. Press [ENT]. Nets 1-5 are always available when the function switch is in position 1-5. Press [ENT]. o.5.0 kHz.3 Frequency Hopping Net Programming Perform the following procedure to program a frequency hopping net: a. The net preset name can be changed from the default NET## to any name. or OFF. use the left/right arrows to select SQUELCH. or HIGH transmit power level and press [ENT]. If ACTIVATE IN LIST? is set to YES. Use the up/down arrows to select the CTCSS tone frequency from the list and press [ENT]. use up/down arrows to select FM DEVIATION of either 5. b. c.2. or 8. and then press [ENT]. If Digital Squelch is desired.0 kHz for analog voice transmissions. 4. select NORM and press [ENT].5 kHz. r. s. and press [ENT]. that net is not available when the function switch is set to off. Use the numeric buttons to enter the number of the net to be programmed. Use the up/down arrows to select LOW. For WBFSK and FM. NOISE. p. that net is available to the operator. Use the left/right arrows to select NAME.5. q. If Continuous Tone Controlled Squelch System (CTCSS) is to be used. and then select ON and press [ENT]. 4-19 . Use the left/right arrows to select POWER and press [ENT]. If ACTIVATE IN LIST? is set to NO. set CTCSS to ON. If not used. leave the default OFF setting. Then enter the transmit hopset compartment number and press [ENT]. Use the up/down arrows to select VOICE. Use the left/right arrows to select DATA/VOC and press [ENT]. MEDIUM.6 e. Enter encryption key number and press [ENT].3. Enter the receive hopset compartment number and press [ENT]. k.5. refer to Appendix B.4. l. or HIGH and press [ENT]. Use the up/down arrows to select LOW. If Directed Calling or Wireless IP operation are to be used. Use the left/right arrows to select COMSEC and press [ENT]. set RECEIVE ONLY to NO. j. Press [ENT].14 for information about operating the radio in scan mode. SCAN MENU When the radio is in scan mode. DATA. i. Use the left/right arrows to select NAME. f. refer to Paragraph 4. For information on creating a hopset compartment.2 for information on programming encryption keys.1. or DATA OR VOICE (D/V) and press [ENT]. set RECEIVE ONLY to YES.5. Refer to Paragraph 3. Use the up/down arrows to choose SIMPLE for the D/V type and press [ENT]. 4-20 . Refer to Paragraph 4. If the radio is to be in radio silence on the net. Use the left/right arrows to select POWER and press [ENT]. Up to 25 nets can be programmed in the scan list. Press [ENT]. g. h. only fixed frequency simple radio nets that are programmed into the scan list are scanned. up to 12 characters long. The net preset name can be changed from the default NET## to any name.1. Press [ENT]. Use the left/right arrows to select HOPSET and press [ENT]. If the radio is able to transmit on the net. Select FREQUENCY HOPPING and press [ENT]. To review scan list. Use the left/right arrows to select PRIORITY and press [ENT]. The radio checks the priority receive net every three nets so that it is checked more frequently for signal presence than the other nets. Press [ENT]. e. 4. The priority transmit net is the net that the radio transmits on if the Push-to-Talk (PTT) button is pressed when the radio is actively scanning. 4-21 . Perform the following procedure to configure transmit and receive priority nets: a. a priority transmit net and a priority receive net can be programmed into the radio.6.1 Scan List Programming Perform the following procedure to program a scan list: a. Press [ENT]. b. b. f. select REVIEW. Use the left/right arrows to select LIST and press [ENT].6.6.4. Use the up/down arrows to select the net to delete. d. Use the up/down arrows to scroll to desired PRIORITY TX NET and press [ENT]. Use the left/right arrows to select ADD and press [ENT]. c. Repeat until all desired nets are in list. Enter a two-digit net number and press [ENT]. select DELETE. To delete a net from the scan list. c. Press [ENT]. Use the up/down arrows to scroll through the scan list.1). Press [PGM] and use the left/right arrows to select SCAN.2 PRIORITY Programming Once nets are added to the scan list (refer to Paragraph 4. Press [PGM] and use the left/right arrows to select SCAN. use the up/down arrows to select YES or NO. external GPS. PORTS MENU The RF-5800M-HH has a side connector that can be used for remote control operations. the only way to keep the radio from returning to automatic scan mode is to press either the PTT or CLR buttons. Enter desired HANG TIME (valid range 0 to 99 seconds) duration and press [ENT]. or audio operations. e. 4-22 . Press [PGM].6. use the up/down arrows to scroll to desired PRIORITY RX NET and press [ENT]. Use the left/right arrows to select CONFIG and press [ENT]. use the left/right arrows to select SCAN. Hang time is the length of time after which the radio returns to automatic scan mode after signal presence is lost on a net. If hold time is enabled.7 a. Use the numeric and/or left/right arrows to input a value (in seconds) between 01 and 99. YES or NO. CONFIG Programming Scan CONFIG programming allows the operator to configure the radio's hang time and hold time. Hold time is the length of time that the radio. and press [ENT]. after detecting signal presence on a net. b. Ports programming allows this connector to be configured for these functions. d.d. Press [ENT]. 4.1 The radio prompts: ENABLE RX PRIORITY SCANNING?. the operator is prompted HOLD TIME. At ENABLE HOLD TIME?.2. will return to automatic scan mode even if the signal is still present on that net. data devices. See Figure 4-1. If YES is selected. Perform the following procedure to program scan configuration: 4. If YES is selected for enabling hold time. c. The DATA PORT TYPE will be shown. Press [PGM]. ASYNC RATE 2. b. c. 4-23 . Press [PGM]. Use the left/right arrows to select REMOTE and press [ENT]. Use the left/right arrows to select DATA and press [ENT].4. STOP BITS 4. use the left/right arrows to select PORTS. Press [ENT].1 REMOTE Port Programming Perform the following procedure to program the REMOTE port as required by the terminal or computer connected to the radio: a.7. FLOW CONTROL 6. b.2 1. PARITY 5. but is not programmable from this menu. use the left/right arrows to select PORTS. DATA BITS 3.7. Use the up/down arrows and press [ENT] to select desired values for the following parameters: 4. and press [ENT]. and press [ENT]. ASYNC ECHO View Data Port Setting Perform the following procedure to view the DATA port setting: a. Use the up/down arrows to choose INTERNAL or EXTERNAL clock source. CFIG MENU Configuration programming consists of general radio settings. This is required for guaranteed CT SCAN RX to work. 4. c. and press [ENT]. the TX DATA CLOCK SOURCE menu will be seen.4. d. Select ON or OFF as appropriate. Select GENERAL and press [ENT]. Select YES or NO as appropriate. and Sensor alerts. b. and press [ENT].8. DATA CLOCK POLARITY can be set for NORMAL or INVERTED.1 GENERAL Settings Perform the following procedure to configure the general radio settings: 4-24 a.8 c. d. . Select ON or OFF as appropriate and press [ENT] when finished. This may be desired to interoperate with legacy equipment. Beacon. Clock settings. use the left/right arrows to select CFIG. external device settings. Press [PGM]. GPS. Setting FM TRANSMIT TONE to ON causes the radio to transmit a 150 Hz tone whenever the PTT button is pressed. Network. Select ON or OFF as appropriate. Setting POWER MANAGEMENT to OFF disables the battery savings modes in your radio. When the DATA PORT TYPE is SYNC. Setting SILENCE BEEPS? to YES prevents the radio from beeping to indicate an operator error. Setting ROBUST PREAMBLE to ON causes the radio to transmit extra training frames in CT VOICE. e. f. SMS. Use the 4-25 . TONE is a constant tone.g. Refer to Paragraph 4. Use the left/right arrows to select BEACON and press [ENT]. Press [PGM]. If TONE was selected. use the left/right arrows to select CFIG. c. use the left/right arrows and the numeric buttons to select an audible frequency for the start (and stop) frequency (between 300 and 3200 Hz). If SWEPT was selected. CAUTION If the side connector is not being used. and press [ENT]. 4. 1.7 for information about port configuration. the ANC CONNECTOR setting should be set to DISABLE to remove the possibility of inadvertently short-circuiting the pins on this connector.8. and press [ENT]. The ANC CONNECTOR setting must be set to ENABLE if programming the radio from RF-6550V VHF-UHF Radio Programming Application. Setting ANC CONNECTOR to DISABLE causes the 18-pin side connector to be placed in an inactive state. b. and press [ENT]. and the beacon frequency in MHz. or if a device such as an external GPS is connected. Use the up/down arrows to select a BEACON TYPE of either TONE or SWEPT. and SWEPT is a ramping tone. use the left/right arrows and the numeric buttons to select an audible frequency for the tone between 300 and 3200 Hz. 2.2 Programming Beacon Settings Perform the following procedure to configure the radio’s Beacon settings: a. Press [ENT]. Press [ENT]. Start and stop tones must be different to create a sweep range. Use the left/right arrows and the numeric buttons to select the beacon ON TIME (001 to 100 seconds). Press [ENT]. Refer to Paragraph 3. Press [ENT].0 MHz to 512. d. as well as battery condition.0 MHz. If OFF TIME is set to 000. Use the left/right arrows to select the Beacon transmitting POWER LEVEL of LOW. Use the left/right arrows and the numeric buttons to select the beacon OFF TIME (000 to 100 seconds). Off Time. will affect the length of time that the beacon can transmit effectively. NOTE Settings for Beacon Power Level.15. Press [ENT]. f. Use the left/right arrows and the numeric buttons to enter the Beacon transmitting frequency from 30. NOTE Beacon power level setting is independent of normal radio transmit power level settings.2 for Beacon operation. and On Time. or HIGH. MEDIUM.left/right arrows and the numeric buttons to select an audio frequency for the stop tone (between 300 and 3200 Hz). the Beacon will always be on. g. Press [ENT]. 4-26 . e. Use the left/right arrows and the numeric buttons to select a sweep rate (1 to 10 Hz) for the ramping tone. Press [ENT]. use the left/right arrow keys to select CFIG. YYYY-MM-DD. Valid entries are: ZULU. 4-27 . 4. the display format will be DDHHMMZ MON YYYY. If DATE FORMAT of Zulu is selected.4. and press [ENT]. d. and MM-DD-YY.3 Programming Clock Settings Perform the following procedure to set the radio’s clock: a. Press [PGM]. e. b. Use the left/right arrow keys to select EXT_DEV and press [ENT]. and press [ENT].4 Programming External Device (EXT_DEV) Settings Perform the following procedure to configure the radio’s external device settings: a. • • • Selecting CO-SITE ON switches in additional co-site filtering on the 50 W power amplifier (PA). Use the left/right arrow keys to select CLCK. and press [ENT]. Selecting BYPASSED bypasses the 50 W PA. enter the NEW DATE followed by the NEW TOD in the selected format. and press [ENT]. Press [PGM]. use the left/right arrow keys to select CFIG. If any other DATE FORMAT is selected. DD-MM-YY. c.8. Selecting CO-SITE OFF switches out the additional co-site filtering on the 50 W PA. Select desired DATE FORMAT and enter the date. where Z is the time zone designator. Set UTC OFFSET as required. based upon the Universal Coordinated Time (UTC) Offset setting. b.8. 9 Programming Falcon Watch™ Sensor Alert Settings Refer to Paragraph B.c. Whenever the transmit frequency is below 108 MHz (VHF range).6 Programming Situational Awareness Settings Refer to Paragraph B.8.5 for this information. 4.6 for this information. 4.8. 4-28 .8.4 for this information. When set to ON. Programming RF-6010 Basestation Settings Refer to Paragraph B. 4. a bias voltage (equal to the battery voltage) is applied to the antenna port for the UHF frequency range 108 MHz to 512 MHz.8 Programming Short Messaging Service Settings Refer to Paragraph B.5 The DC ANTENNA BIAS setting is used when connecting an RF-3162-AT001 Dipole antenna.8. the bias voltage is automatically removed from the antenna port.7 Programming Wireless IP Network Settings Refer to Paragraph B.7 for this information.2 for this information.8. 4. 4. Table 5-1 contains the checks and services that should be performed either on a daily basis when the equipment is in use. a moist sponge.CHAPTER 5 PREVENTIVE AND CORRECTIVE MAINTENANCE 5. Table 5-2 contains the checks and services that should be performed on a weekly basis with the equipment in use. or on a weekly basis when the equipment is in a standby condition. and a cloth to keep equipment clean. and dust-free. Table 5-1.1 PREVENTIVE MAINTENANCE Optimum performance of the RF-5800M-HH is largely dependent on equipment that receives routine. scheduled care and inspection of equipment to prevent equipment failure and to reduce downtime.7. 5-1 . dry. Preventive maintenance is the systematic. Preventive maintenance includes keeping the equipment clean. Daily Preventive Maintenance Checks and Services Check No. preventive maintenance to avoid equipment failures. Use a soft brush. NOTE The RF-5800M-HH does NOT require replacement of a memory Hold Up Battery (HUB). 1 Item to be Inspected Operation Procedure Perform initial tests as outlined in Paragraph 3. Table 5-2.2 Item to be Inspected Procedure 1 Antennas Check for breaks or strains. CORRECTIVE MAINTENANCE Shortcomings and defects which are revealed during preventive maintenance. The type of work required determines if the corrective maintenance procedure can be performed by the operator. The following procedures assume that the operator has determined that the radio is faulty. 5. report the problem to a Level III maintainer. or if it must be performed at a maintenance repair facility. Weekly Preventive Maintenance Checks and Services Check No. This could be determined in three ways: • • • The operator has run self-test and a fault has been identified by the radio. The operator has observed degraded operation that suggests the system is faulty. If the symptom observed is not covered. must be attended to by means of corrective maintenance. the troubleshooting procedures in this chapter should be followed to determine the recommended corrective action. 5-2 . 2 Connectors Inspect for dirt. or which appear when the radio system is in service. repair or replace as required. A run-time fault message is displayed by the radio. corrosion or damage. 3 Protective Caps Ensure protective caps are in place when connectors are not in use. Whenever the operator believes that the radio may be faulty. refer to Paragraph 3. or cases of degraded operation.1. If the recommended action is unsuccessful. 5.2. their meaning and recommended action.2 Non-BIT Faults Non-BIT faults are operator-observed failures. record the fault code. If a fault message is still displayed. cycle radio power and repeat the self-test. Refer to Table 5-4 for a list of run-time warnings.7. report the problem to a Level III maintainer.1.2.1 BIT Faults BIT faults occur following an operator-executed self-test. Locate the observation in the first column of Table 5-3 and follow the recommended action.1. If the radio displays a fault message.2. then report the fault to a Level III maintainer. 5-3 . 5. The following paragraphs identify probable failure causes and suggested corrective actions. For information on running a radio self-test. Self-test faults are shown on the LCD display.5.1 Troubleshooting Procedures Faults can be detected by Built-In Test (BIT) or visual observation. Table 5-3. Non-BIT Troubleshooting Observation Action Radio does not power on. Replace battery with a fresh, charged battery. If radio still does not power up, send unit to maintenance. No Receive (RX)/Transmit (TX) audio; Radio Transmitter will not key when handset Push-to-Talk (PTT) button is pressed. Use a different handset (if applicable). Typically, the handset is used with manpack radios. Intermittent RX audio. Clean handset connectors. Replace handset (if applicable). Table 5-4. Run-Time Warnings Warning Message Displayed 5-4 Description Action *****FAULT ****** SYNTH OUT OF LOCK RF board is temporarily or permanently rendered incapable of RX or TX on the currently loaded frequency. Cycle radio power. If condition persists, this is a CRITICAL system fault. Radio needs repair. ******FAULT****** GPS COMM FAILURE Global Positioning System (GPS) communications is not functioning correctly. GPS can be set to Internal, External, or None. Check source of GPS for proper operation. **CONFIGURATION** ******CLEARED****** This message indicates the loss of all Radio must be reprogrammed. If radio configuration, COMSEC, and condition persists, radio needs TRANSEC data. repair. Table 5-4. Run-Time Warnings (Continued) Warning Message Displayed Description Action *****WARNING ****** NO TEK FILLED Radio was placed into cipher (CT) Put radio in PT or program the switch position with no valid crypto required crypto key. key loaded. *****WARNING ****** NO HOPSET FILLED A hopping net was loaded, but no valid hopset is programmed. *****WARNING ****** LOW BATTERY TEMP Posted if the battery temperature Warm the battery slowly to at least falls below -10° C and DC input is 0° C, but do not overheat. below 11.2 V, or battery temperature falls below -20° C. *****WARNING ****** LOW BATTERY VOLTAGE Radio must be programmed with valid hopset. Posted if the DC input operating Replace current battery with voltage drops below 9.5 V in TX or charged battery. 10.75 V in RX. *****WARNING ****** LOW BATTERY Posted if battery charge capacity is critically low. Replace current battery with charged battery. *****WARNING ****** NO CRYPTO SYNC Encrypted traffic was received but the CITADEL was unable to synchronize on the information. Under normal conditions this might be an indication of poor RX signal quality or the wrong TEK was used. CITADEL configuration might also be different between the two radios. Make sure both radios are using the correct TEK. Verify CITADEL configurations are identical by comparing the part number information on the TESTVERSIONS-HARDWARE displays. Validate signal quality by using another frequency, or PT voice operation. 5-5 5.3 BATTERIES The RF-5800M-HH is supplied with a rechargeable high-capacity Lithium-Ion (Li-ION) battery. Refer to Paragraph 2.2 and see Figure 2-3 for information on installing the battery onto the transceiver. 5.3.1 Battery Life Battery life is the approximate amount of time a battery can be used before it needs recharging or replacing. The RF5800M-HH battery charge indicator can be used to help determine battery condition, refer to Paragraph 3.7.3. The chief factor in determining battery life is transmission power and duty cycle. To maximize battery life, transmit as little as possible, and utilize the lowest transmit power level required to successfully communicate. Refer to Table 5-5. The battery life data is provided as a guideline and is typical data at +21° C with a 10% transmit, 10% receive, 80% idle (squelched) operating cycle. Actual results may vary. Battery life for models with internal GPS will be slightly less. Battery life is dependent on battery age, temperature, charge times, and backlight use. Battery life will decrease approximately 20 - 25% at -20° C. 5-6 25 15 hours CT Voice.3. Optional Two and Single-Bay Battery Chargers (RF-5853-CH002 and RF-5853-CH001) provide fully-automatic charging for the RF-5800M-HH Li-ION battery pack.Table 5-5.30 hours PT/CT Hopping Voice. RF-5800M-HH Typical Battery Life Transmit Power Radio Operation VOICE DATA 5W 2W CT Voice.25 hours 15.25 hours PT/CT Hopping Data 11. It displays the status of each battery inserted into the charger bay during operation.5 hours 22. Charging times may vary. headset/handset 14.5 hours 15 hours 11 hours 15 hours PT Text Data 5.2 Recharging the Li-ION Battery Packs WARNING Do not attempt to recharge a disposable Lithium battery.25 hours 20 hours PT Voice. speaker volume 90% 11. speaker volume 90% 14.5 hours PT Voice. It displays the status of the battery 5-7 . speaker volume 90% 11 hours 14.75 hours 22. headset/handset 11. It is capable of simultaneously charging up to six batteries in less than three hours at room temperature.75 hours CT Data 14. The optional RF-5853-CH006 Six-Bay Battery Charger (10211-2300-01) provides fully automatic charging for the RF-5800M-HH Li-ION battery pack. Do not expose to fire or temperatures above 160° F (71° C). The battery pack should be wrapped with insulating material. and packed for disposal. incinerate.pack when inserted into the charger bay during operation. or mutilate the lithium-ion battery. Completely discharge batteries before proper disposal.3 Disposing of Li-ION Batteries WARNING Do not dispose of Li-ION batteries in uncontrolled trash. reverse polarity. Partially discharged batteries may contain a significant amount of energy and should be handled with care. WARNING Do not crush. disassemble. A separate manufacturer's battery charger manual is supplied with each battery charger. such as plastic. 5-8 . 5.3. Refer to Paragraph 3. The RF-5800M-HH monitors the absolute state of charge of the battery. observe the following: • • • It is not necessary to wait until the battery is completely discharged before recharging the battery.4 Battery Storage and Maintenance For maximum battery life. Recharge the battery after long periods of non-use (six months) to maximize battery life. Replace the battery when it no longer provides acceptable performance.3. The battery can be recharged several hundred times before requiring replacement.5.7.3 for a complete description. • • • Store unused batteries in a cool. 5-9 . Keep the battery's metal contacts clean. dry place. 5-10 .This page intentionally left blank. 150 ohm Selects Auxiliary power when active low When disabled acts as microphone 3. Table A-1.3 V bias Audio Audio Audio Audio When disabled. When enabled.APPENDIX A A. aux power acts as the microphone. Table A-5 provides part numbers for the mating connectors.0 Vrms. AUDIO Connector (2 m Models) Pin # Signal Name A B C ADF_A ADF_B ADF_C D E ADF_D ADF_E F ADF_F Dir Description N/A Ground.3 V through 15 kohm.1 CHASSIS CONNECTOR PINOUT DATA Table A-1 through Table A-4 provide pinout data for the external connectors mounted on the RF-5800M-HH chassis. See Figure A-1 for connector pinout details.8 V nominal. 600/1000 ohms Pulled-up 3.6 mVrms. ground to activate 2. the switched power output is 10. Analog O Variable Audio Output I Handset Push-To-Talk (PTT) I Audio In I Auxiliary Power Select O Electret Microphone Bias/Auxiliary Power Specifications Notes/Modes Ground 3. A-1 . 8 V nominal.0 Vrms. 600/1000 ohms Audio 3 /AUX_PTT I Handset Push-To-Talk (PTT) 15 kohm pulled-up to 3.6 mVrms. the switched power output is 10.Table A-2. 150 ohm Audio 5 AUX_PWR_SELECT I Auxiliary Power Select Selects Auxiliary power when active low 6 BIAS_V O Electret Microphone Bias/Auxiliary Power 1k ohm pull-up to 3. AUDIO Connector (20 m Models) Pin # Signal Name Dir 1 Ground O Ground. aux power acts as the microphone.3 V 7 N/A A-2 Description N/A None Specifications No connect Notes/Modes When disabled. Analog Grounded to shell Audio 2 AUX_AUDIO_OUT O Variable Audio Output 3.3 V shunt to ground to activate Audio 4 AUX_AUDIO_IN I Audio In 2. When enabled. . 115 ohm sink) 4 NC 5 ANC_PTT 6 Test.Table A-3. Retransmit No Connect Reserved I Auxiliary Audio Keyline H-250 Compatible Test. Retransmit 10 ANC_DAT_RXC O Synchronous Receive Data Clock RS-232/MIL-STD-188-114A Data Port 11 ANC_DAT_TXD I Transmit Data RS-232/MIL-STD-188-114A Data Port 12 ANC_DAT_RXD O Receive Data RS-232/MIL-STD-188-114A Data Port 13 ANC_RMT_RXD I Remote Control Receive Data RS-232/MIL-STD-188-114A Remote Port A-3 . Retransmit ANC_RT_OFF I Overrides On/Off Switch Test 7 ANC_DAT_DCD O Data Carrier Detect RS-232/MIL-STD-188-114A Data Port 8 ANC_DAT_RTS I Request To Send RS-232/MIL-STD-188-114A Data Port 9 ANC_AUDIO_IN I Auxiliary Audio Input 0 dBm nominal Test. 20 mA Retransmit max. Side Connector Pinouts Pin # Signal Name Dir Description Specifications Notes/ Modes 1 ANC_SIG_GND Signal Ground 2 ANC_AUDIO_OUT O Auxiliary Audio Output (Optional) H-250 Compatible 3 RETRANS O Retransmit Out Active low Open Drain (15 V max. VHF-UHF ANTENNA Connector Pin # Signal Name Dir Shield Antenna Coax Ground N/A Ground Center RX/TX RF I/O A-4 Description Receive and transmit signal Specs Notes/ Modes TX: 5 watts max . Side Connector Pinouts (Continued) Pin # Signal Name Dir Description Specifications Notes/ Modes 14 CABLE_PRES I Cable Sense No connect on 4200 board 15 ANC_RMT_TXD O Remote Control Transmit RS-232/MIL-STD-188-114A Data Remote Port 16 ANC_PWR O 9.14 VDC External 30 mA @ 60 C Power Supply (Switched) Eng use only 17 ANC_DAT_CTS O Clear-To-Send RS-232/MIL-STD-188-114A Data Port 18 ANC_DAT_TXC I Synchronous Transmit Data Clock RS-232/MIL-STD-188-114A Data Port Table A-4.3 .Table A-3. 2 M and 20 M Connectors and Mating Connector Part Numbers Connector Part Number Radio Chassis Connector 6-Pin Audio J69-0001-623 7-Pin Audio J40-0023-007 Side Connector 12011-9020-01 7-PIN AUDIO (20 M) SIDE CONNECTOR 6-PIN AUDIO (2 M) 16 18 1 3 A 2 1 7 6 5 3 4 B E F D C F-0234-4200-017 Figure A-1.Table A-5. Radio Connector Pinouts A-5 . This page intentionally left blank. A-6 . Paragraph B.4 Wireless Internet Protocol (IP) Network .7 B-1 .Paragraph B.3 Situational Awareness .1 INTRODUCTION This appendix describes advanced features of the RF-5800M-HH.5 Short Messaging Service (SMS) . See Figure B-1 for the programming menu of these advanced features.6 Falcon Watch™ Sensor Alerts . Refer to Figure 4-1 for other basic programming menus.Paragraph B.Paragraph B.APPENDIX B ADVANCED FEATURES B. • • • • • • RF-6010 Basestation Support .2 Directed Calling .Paragraph B.Paragraph B. VWX 8PGM TO SHEET 2 NORM NET D/V TYPE SELECT SELECT NET TO MODIFY ## NET NAME ACTIVATE IN LIST? YES NO NET TYPE FIXED FREQUENCY OR FREQUENCY HOPPING DATA/VOC DATA/VOICE VOICE DATA DATA OR VOICE (D/V) SIMPLE MODULATION FM AM WBFSK ASK DIRECTED RADIO ADDRESS: ### DEFAULT GATEWAY: ### WIRELESS IP RADIO ADDRESS: ### NETWORK ADDRESS: ###. 1600. F-0234-4200-0018-2 Figure B-1.### B FM DEVIATION 8.0 kHz CTCSS (REFER TO NOTE 1) OFF ON CTCSS TONE BAUD RATE (REFER TO NOTE 1) 16.0 kHz 6.###. DATA/VOICE SELECTIONS AFFECT WHAT OPTIONS ARE AVAILABLE FOR SIMPLE MODULATION. 2666.0 K. 8000 DEFAULT GATEWAY ### NETWORK TOPOLOGY MESH EXCLUSIVE POINT NOTES: 1. NOT VISIBLE IN A SIMPLE NET.5 kHz 5.###. Advanced Features Programming Menu (Sheet 1 of 3) B-2 . ### AUTO NOTE: 2.###.### AUTO POSITION FORMAT MGRS UTM/UPS L/L-DMS L/L-DM DATUM REFER TO TABLE B-2 LINEAR UNITS METRIC STATUTE NAUTICAL ELEVATION FORMAT DATUM BASED MEAN SEA LEVEL ANGLE FORMAT DEG/MAGNETIC MIL/TRUE NORTH MIL/MAGNETIC DEG/TRUE NORTH AUTO REPORT NEVER TIMED REPORT INTERVAL XXXX SECONDS POSITION SERVER CUSTOM IP POSITION SERVER ###. SELECTING EXTERNAL GPS OPERATION WILL DEFAULT REMOTE PORT SETTINGS TO 4800 BAUD. 8 BITS. 1 STOP BIT.###.### AUTO INTERNAL (SEE NOTE 3) GPS SLEEP MODE NONE AUTO POSITION FORMAT MGRS UTM/UPS L/L-DMS L/L-DM DATUM REFER TO TABLE B-2 LINEAR UNITS METRIC STATUTE NAUTICAL ELEVATION FORMAT DATUM BASED MEAN SEA LEVEL ANGLE FORMAT DEG/MAGNETIC MIL/TRUE NORTH MIL/MAGNETIC DEG/TRUE NORTH AUTO REPORT NEVER TIMED REPORT INTERVAL XXXX SECONDS POSITION SERVER CUSTOM IP POSITION SERVER ###. NOT VISIBLE UNLESS RADIO HAS INTERNAL GPS. ECHO OFF.###. F-0234-4200-0018-2 Figure B-1. Advanced Features Programming Menu (Sheet 2 of 3) B-3 . NO PARITY.B FROM SHEET 1 CFIG EXTERNAL (SEE NOTE 2) C GPS GPS OPERATION MODE NONE SEE SHEET 3 POSITION FORMAT MGRS UTM/UPS L/L-DMS L/L-DM DATUM REFER TO TABLE B-2 LINEAR UNITS METRIC STATUTE NAUTICAL ELEVATION FORMAT DATUM BASED MEAN SEA LEVEL ANGLE FORMAT DEG/MAGNETIC MIL/TRUE NORTH MIL/MAGNETIC DEG/TRUE NORTH AUTO REPORT NEVER TIMED REPORT INTERVAL XXXX SECONDS POSITION SERVER CUSTOM IP POSITION SERVER ###.###.###. NOTE: 3.###. C FROM SHEET 2 SMS CLCK CANNED REFER TO PARAGRAPH 4.2 K F-185-4200-0018-3B Figure B-1.### SETTING IS NOT PROGRAMMABLE BAUD DATA RATE 115.###.3 EDIT DELETE DELETE ALL SETTINGS TEXT ENTRY MODE INSERT OVERWRITE 1-10 TEXT PREDICTION ON OFF TONE ALERT ON OFF CAP MODE ON OFF ACKNOWLEDGE ON OFF EXT_DEV NETWORK EXTERNAL 50 W PA MODE CO-SITE ON CO-SITE OFF BYPASSED DC ANTENNA BIAS OFF ON UHF RECEIVE PATH BYPASS LNA ALERTS PPP ENABLE PPP PORT NO YES ADDRESS IP ADDRESS ###.###.### SETTING IS NOT PROGRAMMABLE NEGOTIATED PEER IP ###.4 K 19.6 K 38. Advanced Features Programming Menu (Sheet 3 of 3) B-4 .###.###.###.###.8.### PEER IP ADDRESS AUTO SETTING IS NOT PROGRAMMABLE ALERTS ENABLE ON OFF ALERT DISPLAY ON OFF ALERT TONE ON OFF STATUS NEGOTIATED IP ADDR ###.2 K 57. Phone-to-phone communications through the RF-6010 Basestation. Telephony capability requires use of the Harris RF-6010 Tactical Network Access Hub and associated peripheral equipment. Computer Telephony Interface (CTI) calls when configured as a RF-6010 Basestation. refer to the RF-6010NW-001 Tactical Network Access Hub User Manual. See Figure B-3 for an example of a telephony network.0. Wireless networking capability and telephony capability are provided for radios that support wireless Internet Protocol (IP) functionality. B-5 . Harris Session Initiation Protocol (HSIP) V2. Harris Publication Number (10515-0262-4200).B. Operation of RF-6010 similar to Directed Calling when configured as a telephony gateway. The RF-5800M-HH radio supports: • • • • • Ability to transmit and receive voice/data to and from the RF-6010 Basestation. For more information. The RF-5800M-HH can be used as an outstation to perform telephony calls to the RF-6010 Basestation. The RF-6010 must be programmed using the RF-6010 Programming Application prior to programming the base radios. RF-5800M-HH radios directly connected to the RF-6010 can be programmed through the RF-6010.2 RF-6010 BASESTATION The RF-5800M-HH radio supports a direct Point-to-Point Protocol (PPP) connection to the Harris RF-6010 Basestation for telephony and IP data communications. B. radios not participating in it have the ability to request a directed call. B-6 . B. The call may be performed in either fixed frequency or frequency hopping. The break-in radio will not hear a response from the directed call radios until the virtual circuit is released. If the channel does not free up after 20 seconds. the radio will display CALL FAILED: NO RESPONSE. If the channel is actively participating in a directed call. The request is placed in a queue and waits for the channel to be freed for use.3. The radios in the directed call can hear the incoming message. Directed Calls create a virtual circuit by reserving a channel. Radios in the net that are excluded from the directed call are not able to hear or participate in the conversation. After a transmission has completed on the circuit. the radio inactivity timer is started. they have the ability to break-in on a directed call. the circuit will be terminated. If there has been no activity on a directed call circuit for 20 seconds. Channel reservation informs other radios on the net that the channel is occupied. This is a transmit-only function. Since channel reservation and release consists of special signaling that uses a handshake mechanism to establish and tear down virtual circuits. intended for emergency use to alert the participants. or Data/Voice (D/V). Calls support Plain Text (PT) and Cipher Text (CT) in Voice (VOC). This indication appears on the front panel of the excluded radios as a BUSY-VOICE status message. but the radio outside the call will still not be able to listen in.1 Description The Directed Calling feature allows a radio operator to hold a private voice conversation with another radio in the net. only radios on nets that have a programmed radio identification (ID) may utilize this feature. Although these radios may not participate in the call.3 DIRECTED CALLING The following contains information and programming instructions for Directed Calling. A channel is defined as a fixed frequency or a set of hop frequencies. then NORM is displayed. c. If the current net does not support directed calling. A station name is an easy to remember name that associates radio IDs with particular radio nets.A radio operator initiating a directed call is presented with the option of using either a station name or radio ID. either the station name (if one has been programmed) or radio ID of their other party is displayed on the bottom line of the display. Only the two radios participating in the call will hear the audio. NOTE If no stations have been programmed by the VHF-UHF RPA. then the operator will only be presented with the option of using a radio ID to make a call.Ultra High Frequency (VHF-UHF) Radio Programming Application (RPA) can be used to preload a list of up to 50 radio stations into the radio. Select the ADDRESS TYPE and press [ENT]. Perform the following to make a direct call using a radio ID: a. d. or no stations have radio IDs associated with the current radio net. use the up/down arrow keys to select RADIO ID and press [ENT].3. From the main menu. If the current radio net supports directed calling. b. If default gateway is programmed for RF-6010. B-7 . use the up/down arrow keys to select RADIO for CALL TYPE and press [ENT]. If radio names are programmed. The Very High Frequency . press the [CALL] button. B. When a directed call has been established. then the radio’s ID is displayed on the top line to the right of the battery status bar.2 Initiating a Directed Call Using a Radio ID The Directed Calling feature allows a radio user to establish a private voice call between two radios. During this time. f. After a few seconds.2.3. Use the up/down arrows to select YES. B-8 . g. If the PTT button is released after the radio has broken into the directed call. To break into the directed call. B.2 Breaking into a Directed Call When a channel is reserved (directed call in process).e. B. radios not participating in the directed call will not be able to transmit on the net. With a directed call in process. Perform the following to terminate a directed call using a station name: a.254) to be called. the complete break-in process needs to be repeated for the radio to transmit over the reserved channel again. The privacy of the directed call is still maintained since the operator breaking in cannot hear the directed call participants. an operator can hold down the PTT button for five (5) seconds. The radio is linked to another radio.3. Use the keypad to enter the three-digit RADIO ID (001 . the operator is notified that the radio cannot transmit by emitting a tone and displaying a BUSY status on the main screen. b. then press [ENT] to terminate the link. If the Push-To-Talk (PTT) button is pressed. The radio will then break in and begin to transmit once the busy tone stops.2. The radio initiates a call and establishes a circuit to a particular radio ID. and press [ENT].1 Terminating a Directed Call The radio operator can terminate a directed call at any time. the radio will emit a busy tone to indicate that it is not transmitting. The radio ID of the other radio in the directed call is displayed at the bottom of the screen. press the [CLR] key. the screen will change to the main menu. If the operator presses the PTT button. B-9 . Net programming in the RF-5800M-HH consists of all the data that describes a radio net including name. B.B. data and voice types. B. etc.2. utilize the directed call queue.4 Radio Call Inactivity Timer If the PTT button has not been keyed and no traffic has been received on a directed call for a period of 20 seconds. frequency. etc. For the radios that are excluded from the directed call.3. The radio operator has the choice to wait for the directed call to terminate.1 Net Programming A radio net is defined as a group of radios that share common communication parameters. transmit power.3 Directed Calling Programming This section describes programming the Directed Calling feature from the radio front panel.2.3.3 Busy State A radio that is excluded from a directed call cannot transmit/receive messages on the net until the call is terminated. Refer to Chapter 4 for general radio programming.3. BUSY-VOICE appears on the Liquid Crystal Display (LCD). squelch.3. data/voice settings. the radio will warn the operator that it cannot transmit by emitting a tone. or break into the directed call. B. such as frequencies. the call is terminated due to a timeout.3. This enables phone calls to be placed. k. b. Press the [PGM] button. B-10 a. . Enter the NET number to be used and press [ENT]. Use the up/down arrow keys to select YES to ACTIVATE IN LIST and press [ENT].Perform the following to program a radio for Directed Calling. h. Assign a radio ID number for the RADIO ADDRESS (001 . g. Assign the base radio ID number (DEFAULT GATEWAY) to interoperate with an RF-6010 and press [ENT]. Use the left/right arrow keys to select NET and press [ENT]. c. j. e. Use the left/right arrow keys to select DATA/VOC and press [ENT]. select NORM. Use the up/down arrow keys to select BAUD RATE (for data) and press [ENT]. Use the up/down arrow keys to select FIXED FREQUENCY or FREQUENCY HOPPING and press [ENT]. f.254) and press [ENT]. Use the up/down arrow keys to select the Fixed Frequency Modulation (FM) deviation (FM DEVIATION) to be used for net communications and press [ENT]. Use the up/down arrow keys to select DIRECTED and press [ENT]. d. l. If an RF-6010 is not present on this radio net. Use the up/down arrow keys to select DATA OR VOICE (D/V) or VOICE. and press [ENT]. i. and press [ENT]. use the default value (000). is currently in a circuit. is in a different operating state. Error Messages and Corrective Actions Fault Message Corrective Action CALL FAILED NO RESPONSE The targeted radio is not listening on the current frequency. or poor signal strength has caused the radio to miss the overthe-air signaling.B.3. Table B-1. verify that the programmed parameters are valid. PRESS CLR/ENT TO CLEAR B-11 . Place the call again.4 Error Messages and Corrective Actions Table B-1 shows error messages and corrective actions that may be encountered during directed calling. It is assumed that the radio has been programmed correctly and this is not the reason for the error. When in doubt. however. The remote sites may be radios or sophisticated applications running on PCs. NOTE The radio operator can send a position report to any remote net location.4. and then the information can be transmitted to a remote site. RF-5800M-HH radio operators can view their own current position.1 Description Situational Awareness (SA) is the ability to provide remote sites with information about a radio’s geographical position.4 SITUATIONAL AWARENESS (SA) The following contains information and programming instructions for Situational Awareness (SA) in the RF-5800M-HH. The RF-5800M-HH can use either the optional internal GPS module or an external GPS device to read the position. and store/view other remote station positions. The radio can calculate the distance and bearing of each remote station relative to its own current position. however.B. When a radio receives a remote station’s position. it will automatically store the location in memory. The radio will store up to 50 remote station positions. Situational Awareness reports can be sent via fixed frequency or frequency hopping. the stored locations are not saved when the radio is turned off. the net must be set up for Directed Calling and operating in Cipher Text (CT). This positioning information is provided via the Global Positioning System (GPS). B. B-12 . minute (L/L-dm). • Position Format: This setting determines how position information is displayed. Latitude/Longitude-degree. second (L/L-dms). it is recommended that the external GPS receiver be turned off and disconnected from the radio when it is not required to send a position report. • Angle Format: The radio operator can control the heading display. miles per hour). Latitude/Longitude-degree. B. Metric (meters. or Statute (feet. Therefore. • Linear Units Format: The radio operator can select the units of altitude and velocity displays. minute. Selections are: • • • • DEG/TRUE NORTH (degrees referenced to true north) DEG/MAGNETIC (degrees referenced to magnetic north) MIL/TRUE NORTH (mils referenced to true north) MIL/MAGNETIC (mils referenced to magnetic north) B-13 . Universal Transverse Mercator/Universal Polar Stereographic (UTM/UPS). Selections include Nautical (feet.NOTE Maximum communications range can be achieved when interfering devices are kept at a distance from the radio.4. Selections include Military Grid Reference System (MGRS).2 SA Features The user can select the format of the reported position information using the RF-5800M-HH front panel menus. • Elevation Format: The operator can control whether altitude is based on Mean Sea Level or the currently selected datum. kilometers per hour). knots). 3.2.4.3.3. e. and press [ENT]. B.3 SA Operation This section describes how to use the SA feature of the RF-5800M-HH radio to either transmit or view positional information.). b.4.3. Use the left/right arrows to select GPS and press [ENT].1) or SA External Mode (Paragraph B. configure the Garmin GPS receiver to operate with the radio (Paragraph B. d. Set the radio for Cipher Text (CT) operation.Internal GPS To reach the programming menus for configuring SA. The radio contains several pre-programmed datums.• DATUM: Provides positional information used with different kinds of paper maps. f.4.3.3). Press the [PGM] button. c. Configure the radio for SA Internal Mode (Paragraph B.1).3.4. Allow time for satellites to be acquired.3.4. B.3. b. perform the following steps: B-14 a. Perform the following tasks to use GPS/SA: a. . and allows two customized datums to be entered. The system is ready to operate.4. Configure the radio for Directed Calling (Paragraph B. c. Use the up/down arrows to select INTERNAL and press [ENT]. If SA External Mode is being used.1). use the left/right arrows to select CFIG. Connect the cable and power the units (Paragraph B.1 SA Configuration . 4. NOTE Some datums are not supported by the MGRS position format and are not displayed if MGRS is selected. This selects the format of altitude and velocity displays. Datums that are not valid for MGRS are indicated with an asterisk (*) in Table B-2. B-15 . e. The DATUM used when making a map is often noted on the map.. the internal GPS receiver will obtain a position fix and then automatically enter a low power state. Refer to Table B-2.4. UTM/UPS (a universal grid format). the GPS receiver continuously tracks the GPS satellites.d. The radio contains several preprogrammed datums. Use the up/down arrows to choose the desired POSITION FORMAT. miles per hour). knots). Use the up/down arrows to choose the desired GPS SLEEP MODE. the radio will default to WGE. or NAUTICAL (feet. or prior to Auto Reporting. f. and seconds) and L/L-dm (latitude and longitude in degrees and minutes). NOTE The GPS receiver will be taken out of power saving mode if the user manually views GPS position information as described in Paragraph B. minutes. and press [ENT]. If set to NONE. Use the up/down arrows to choose the desired DATUM setting. g. When MGRS is selected and the current datum is not valid for MGRS. kilometers per hour). This menu item determines how position information is displayed. Valid selections are MGRS. In the AUTO setting. Valid settings are METRIC (meters. L/L-dms (latitude and longitude in degrees. STATUTE (feet. and press [ENT]. Use the up/down arrows to select the desired LINEAR UNITS setting. which adjusts the reported position to work with different kinds of paper maps. and allows two customized datums to be entered. ) l. The RF-5800M-HH has the capability to automatically report its GPS position. Use the up/down arrows to set the ELEVATION FORMAT. Valid settings are AUTO and CUSTOM IP. The radio is now configured for SA operation . Use the up/down arrows to select the desired AUTO REPORT setting. This controls whether altitude is DATUM BASED or based upon MEAN SEA LEVEL. The radio will then broadcast GPS information periodically according to the selected report interval value. the user then must enter a REPORT INTERVAL in seconds (5 to 9999). and TIMED. MIL/TRUE NORTH (gunner's mils referenced to true north). . If a non-zero Custom IP is entered. Available selections are DEG/MAGNETIC (degrees referenced to magnetic north). If TIMED is selected. which controls the heading display. (To disable this function. The AUTO setting causes the POSITION SERVER to automatically be set to the Point-to-Point Protocol (PPP) peer IP address. MIL/MAGNETIC (gunner's mils referenced to magnetic north) or DEG/TRUE NORTH (degrees referenced to true north). The RF-5800M-HH can report all stored GPS information to a remote GPS position application.000. Use the up/downs arrows to choose the ANGLE FORMAT. the D/V TYPE SELECT for the current Net has to be DIRECTED or WIRELESS IP. The CUSTOM IP setting requires the full Position Server IP address.000. Use the up/down arrows to select the POSITION SERVER. Press the [CLR] button twice to return to the main screen.Internal mode.000 for the Position Server address. i. Valid options are: NEVER (AUTO REPORT is disabled). k. j. enter 000.B-16 h. the radio will forward GPS information to the selected Position Server every time it receives new GPS information from other radios. For Auto Report to function. Hawaii ANO ANNA 1 Astro 1965. Nigeria Naparima BWI Trinidad/Tobago B-17 . Alaska AFG* Afgooye. UAE ADI-E Adindan. Mean Solution NAR-A North America 1983. Somalia NAR-B North America 1983. Botswana NAS-B North America 1927. Saudi Arabia NAR-E North America 1983. Sudan MVS Viti Levu 16 Fiji Island ADI-C Adindan. 1962 NAR-H North America 1983.Table B-2. Cameroon ADI-M Adindan. Lesotho NAS-C North America 1927. Mexico AIN-B AIN El ABD 1970. Aleutian AMA American Samoa. West US ARF-B ARC 1950. Bahrain NAR-D North America 1983. Canada Antigua. DATUM Abbreviations and Descriptions DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. WGE WGS-84 MIN-B WGC WGS-72 MOD Rome 1940 ADI-A Adindan. Ethiopia MPO M’Poraloko ADI-B Adindan. ISL Astro-43 NAR-C North America 1983. Saudi Arabia ADI-F Adindan. Mali NAH-A Nahrwan Masirah Island ADI-D Adindan. Burkina Faso NAH-C Nahrwan. Conus AIA NAP Minna. Senegal NAH-B Nahrwan. Cocos Islands NAS-A North America 1927. Conus AIN-A AIN El ABD 1970. East US ARF-A ARC 1950. Yukon ARS-A ARC 1960. Canal Zone ASC Ascension Island. Ontario ARF-H ARC 1950. Al British Columbia ARF-F ARC 1950. Kenya/Tanzania NAS-O North America 1927. Tanzania NAS-N Central America 1927 ARS-M ARC 1960. NW Territory ARF-M ARC 1950. Zambia NAS-G North America 1927. Caribbean ASM Montserrat Island. E ALE B-18 . Alaska ARF-D ARC 1950. 1958 NAS-P North America 1927. Malawi NAS-D North America 1927.Table B-2. Iwo Jima NAS-T North America 1927. Zaire NAS-F North America 1927. 1958 NAS-Q North America 1927. Swaziland NAS-E North America 1927. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. Zimbabwe NAS-H North America 1927. Marcos Island NAS-R North America 1927. Eastern Canada ARF-G ARC 1950. Cuba AUA Australian Geodetic 1966 NAS-U North America 1927. Greenland AUG Australian Geodetic 1984 NAS-V North America 1927. ARF-C ARC 1950. Kenya NAS-L North America 1927. Mexico ARS-B ARC 1960. Manitoba. Bahamas ASQ Astro Station 1952. Canada ARF-E ARC 1950. San Salvador ATF Beacon E 1945. Mean NAS-J North America 1927. Burundi NAS-I North America 1927. Wales BUR Bukit Rimpah.Table B-2. Scotland CAC Cape Canaveral OGB-D* Ordinance Survey Great Britain 1936. Bangka OGB-C* Ordinance Survey Great Britain 1936. Czechoslovakia OHA-D Old Hawaiian. Hawaii B-19 . BAT BBOHM* Djakarta. Batavia NAS-W North America 1927. England BOO Bogata Observatory OGB-B* Ordinance Survey Great Britain 1936. Anta OHA-C Old Hawaiian. PH OHA-A Old Hawaiian. Tunisia OHA-M Old Hawaiian. Wales CAI Campo Inchauspe 1969 OGB-M* Ordnance Survey Great Britain 1936 Mean CAO Canton Astro 1966. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. England. South Africa OHA-B Old Hawaiian. W. Hawaii CAP Cape. Ale Bessel-Bohm. Sweden NSD North Sahara 1959 Algeria BER Bermuda 1957 OEG* Old Egyptian 1907 BID Bissau Guinea. Kauai CAZ Camp Area Astro. Maui CCD S-JTSK. Bissau OGB-A* Ordinance Survey Great Britain 1936. CC Mean CHI Chatham Island 1971 OHI-A Old Hawaiian. Oahu CGE Carthage. Iran PRP-H Prov South America 1956. Chile EUR-C Europe 1950. N. Equa EUR-F Europe 1950. Portugal & Spain PRP-D Prov South America Colombia EUR-E Europe 1950. Guyana EUR-G Europe 1950. Guinea OHI-D Old Hawaiian. Brazil OHI-C Old Hawaiian. Channel Islands PRP-G Prov South America 1956.Table B-2. Greece PRP-B Prov South America 1956. Sardinia PRP-M Prov South America 1956. Chile EUR-D Europe 1950. 1960 PLN Pico De Las Nieves COORD Sys 1937. 1967 PIT Pitcairn Astro 1967 Wake Eniwetok. Kauai COA Corrego Alegre. Peru EUR-H Europe 1950. Mean So DOB GUX 1 Astro Guadacanal PHA Ayabelle Lighthouse EAS Easter Island. S. Paraguay OHI-B Old Hawaiian. England. CHU Chua Astro. Norway & Finland PRP-C Prov South America 1956. Oahu DID Deception Island. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. Maui DAL Dabola. Egypt PRP-F Prov South America 1956. Estonia POS Porto Santo 1936 ENW* EST EUR-A Europe 1950. Venezuela EUR-I Europe 1950. Antarctica OHI-M Old Hawaiian. Mean B-20 . West PRP-A PSA 1956 Bolivia EUR-B Europe 1950. Cyprus PRP-E Prov South America 1956. Ireland PTN Pointe Noire 1948 EUR-L Europe 1950. Mean Solution PUR Puerto Rico EUR-S Europe 1950. Guyana GUA Guam 1963 SAN-H South American 1969. Bolivia GAA Gan 1970. England. 1939 SAN-A South American 1969. Peru B-21 . Malta PUK* Pulkovo 1942. NZ SAN-D South American 1969. EUR-J Europe 1950. Iraq. Gizo Island SAN-E South American 1969. IS QAT Qatar National EUR-T Europe 1950. Columbia GRA Graciosa Base 1948 SAN-F South American 1969. Espirito FLO Observ Meteorlog. South Greenland EUS Europe 1979 REU Reunion Mascarene Island FAH Oman SAE Santo 1965. Sicily PTB Point 58 Mean Solution EUR-K Europe 1950. Chile GIZ DOS 1968. Brazil GEO Geodetic Datum 1949. Afganistan SAN-I South American 1969. Argentina FOT Fort Thomas 1955 SAN-B South American 1969. Equador GSE Gunung Segara Kalima SAN-G South American 1969. Paraguay HEN Herat North. Tunisia QUO Qornoq. Russia EUR-M Europe 1950.Table B-2. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. Maldives SAN-C South American 1969. Trinidad&Tabago HJO Hjorsey 55. Iceland SAN-L South American 1969. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. Old Y SAN-J South American 1969.Table B-2. Taiwan SAO SAO Brazil Santa Maria IBE Bellevue Efate N ERR SAP Sapper Hill 1943. Baltra Galap HIT Prov. Thailand SPK-D* S-42 Latvia INH-A1 Indian 1975. Vietnam SPK-C* S-42 Former Czechoslovakia INH-A Indian 1975. Falklands IDN* Indonesian 1974 SCK* Schwarzeck. Thailand SPK-E* S-42 Kazakhstan Ireland 1965 SPK-F* S-42 Albania IRL* B-22 SOA* South Asia. Mean HTN HU-TZU-SHAN. Singapore . India/Nepal SHB Astro DOS 71/4 IND-P* Indian. Thailand SPK-A* S-42 Hungary ING-A Indian 1960. Vietnam SPK-B* S-42 Poland ING-B Indian 1960. Venezuela HKD Hong Kong 1963 SAN-M South American 1969. HER Hermannskogel. Chilean 1963 SAN-K South American 1969. Pakistan SIR South American Geocent Ref IND-S* Indian India INF-A Indian 1954. S. Nambia IND-B Indian Bangladesh SGM Selvagem Grande 1938 IND-I* Indian. Mean TRN S-42 Romania LUZ-A Luzon. Ghana TOY-C Tokyo Okinawa LIB Liberia 1964 TOY-M Tokyo. Island Diego Garcia SRL Sierra Leone 1960 JOH Johnston Island 1961 TAN Tananarive Observation 25 KAN Kandawala Sri Lanka TDC Tristan Astro 1968 KEA* Kertau 1948. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. Caymen TOY-B1 Tokyo South Korea Cycle LEH Leigon. Cairo TOY-B Tokyo South Korea LCF LC5 Astro 1961. W Malay TIL* Timbalai 1948 KEG Kerguelen Island 1949 TIL-S* Timbalai Netherlands KGS Korean Geodesic 1995 TOY-A Tokyo Japan KUS Kusai Astro 1951. ISG ISTS 061 Asto 1968. Philippines Astro Tern Island 1961 LUZ-B Luzon Mindanao Islan USER1* User Entered #1 MAS Massawa.Table B-2. Ethiopia USER2* User Entered #2 MER Merchich Morocco VOI Voirol 1974 Tunisia Algeria MID Midway Astro 1961 VOR Voirol 1960 Algeria B-23 . South Georgia SPK-G* IST ISTS 073 Astro 1969. g.4. Use the up/down arrows to choose the desired POSITION FORMAT.3. f. and press [ENT]. The message *Port Remote Baud: 4800* will display for a few seconds. b. e. DATUM Abbreviations and Descriptions (Continued) DATUM DATUM Description DATUM DATUM Description *Not available with MGRS position format. Mahe Island YAC Yacare Uruguay Minna Cameroon ZAN Zanderij. and press [ENT]. use the left/right arrows to select CFIG.2 Midway Astro 1961-1 WAK Wake Island Astro 1952 Mahe 1971. and press [ENT]. perform the following steps: B-24 a. Use the left/right arrows to select GPS and press [ENT]. and press [ENT]. and press [ENT]. Use the up/down arrows to select EXTERNAL and press [ENT]. Use the up/down arrows to choose the desired LINEAR UNITS. and press [ENT]. MID-1* MIK MIN-A B. Use the up/down arrows to choose the desired ANGLE FORMAT. Suriname SA Configuration . c. Press the [PGM] button.Table B-2. d.External GPS To reach the programming menus for configuring SA. h. Use the up/down arrows to choose the desired DATUM. Use the up/down arrows to choose the desired ELEVATION FORMAT. . The main menu will appear. Perform the following procedure to configure the Garmin Etrex Vista® for use with the RF-5800M-HH: a. Use the up/down arrows to select the POSITION SERVER. B-25 .000. Turn the GPS receiver on by pressing the On/Off button down for at least two seconds.4. Valid settings are AUTO and CUSTOM IP. enter 000. The AUTO setting causes the POSITION SERVER to automatically be set to the PPP peer IP address. NOTE This procedure only details the settings required to achieve compatibility with the RF-5800M-HH radio. If TIMED is selected. Refer to the Garmin manual for operating details not covered here. This will repeatedly transmit GPS information at each scheduled time interval. the user must configure and connect the Garmin GPS receiver to the RF-5800M-HH radio side connector.3.) k. and press [ENT]. and press [ENT]. (To disable this function. Press the [CLR] button twice to return to the main screen. The CUSTOM IP setting requires the full Position Server IP address. the radio will forward GPS information to the selected Position Server every time it receives new GPS information from other radios. The radio is configured for GPS/SA operation. If a non-zero Custom IP is entered.3 Using the External GPS Receiver To initiate Situational Awareness reporting using external GPS.000 for the Position Server address. B. enter the reporting interval in seconds (5 to 9999). The RF-5800M-HH can report all stored GPS information to a remote GPS position application.i.000. Use the up/down arrows to choose whether AUTO REPORT is NEVER or TIMED. j. B. Click X to return to the Setup menu. . d. Click X twice to return to the main menu. select Units>Map Datum >WGS84. Turn power on to the radio and the GPS receiver. d. but may require different cables and configuration. From the Garmin Setup menu.3.Connecting the Units Perform the following procedure to begin operation: B-26 a. Align the pin on cable connector with the hole above the radio’s side connector contacts. c. Use (120110280-A006) cable for the Garmin Etrex Vista®. Hold the connector firmly in place while tightening the thumb screw.b. Do not overtighten. Ensure that the GPS receiver has line-of-sight visibility to the sky.3. Click X to return to the Setup menu.4. c. From the Garmin Setup menu. or (12011-0875) cable for Garmin GPS 76. select System>GPS>Normal to enable GPS tracking. b. select Setup>Interface>NMEA IN/NMEA OUT. NOTE Other GPS receivers can be used. The Etrex Vista® GPS receiver is configured for proper operation. From the Garmin main menu. e.1 GPS External Mode . Make sure the groove on the cable connector is aligned properly with the receptacle.There should be at least three satellites available to obtain positioning information. and allow several minutes for satellite acquisition. The baud rate will automatically default to 4800 bps. and then slide the cable connector down onto the GPS receptacle. Attach the cable to the GPS receiver by first opening the rubber cover on the back of the unit. therefore. g.1). Press the circle arrow button to view the current heading/velocity. Use the left/right arrows to select GPS. and then press [ENT]. Press the [OPT] button. If Auto Report is not enabled. b. and press [ENT]. Press the [OPT] button.e. it can only be viewed in other stations’ saved data. Press [CLR] three times to return to the main screen. velocity. Press the circle arrow button again to view altitude. NOTE Distance is relative to the sending radio. B-27 . altitude. the user must perform a Forced Report to send information manually (refer to Paragraph B. Viewing SA Information To view SA position. and distance data: a. To view SA data received from remote radios in the net: a. it will begin sending SA information at the programmed intervals. b. The current position is shown on the display. B. c.4 If the radio has been configured to Auto Report. heading. d.4. Use the left/right arrows to select GPS.4. e. f. Press the circle arrow button again to return to the position screen. and press [ENT]. Select VIEW.4. Use the left/right arrows to select GPS. d. and then press [ENT]. e.3 for Directed Calls. Refer to Paragraph B. velocity. Forced Reporting of GPS/SA Information In Cipher Text (CT) mode. Select VIEW. or Paragraph B. the GPS position can be reported at any time if the net supports the Directed Calling feature. b. The current GPS position is shown on the display. and press [ENT].4.5 for Wireless IP. GPS position is transmitted. Select REPORT. B-28 . NOTE The current net must be configured for Directed Calling or Wireless IP.c. and press the circle arrow button for altitude information. Use the up/down arrows to scroll through saved GPS/SA data for any other stations (up to 50). and then press [ENT].3. To transmit the current GPS information to other radios: a. B. Press the [OPT] button. c.1 Press the circle arrow button to view the last saved heading.4. NOTE Stored positions are not saved when the radio is turned off. Select the desired station to view the last saved position. the limited bandwidth of narrowband radio communications will make the use of some applications impractical. the radios are behaving like a bridge rather than a router.automated channel selection is not performed by the radio. B-29 . the radio offers an easy way to configure a wireless network without the need of adding and maintaining routes on PCs and radios. where a channel is defined as an individual frequency or as set of hop frequencies.1 Theory of Operation The operation detailed here uses the fixed frequency and frequency hopping in the radio for IP data delivery.B.5.X radio net. See Figure B-2 for a basic network configuration for wireless IP data operation. A bridging device is able to provide IP packet connectivity between different media within the same IP subnet space.168. B. Any application that uses the IP protocol can be used. This easy way to configure a wireless network is known as bridging. This feature permits the radio to interface with devices such as laptops using the radio’s PPP interface. the radios automatically bridge received packets over to the connected computer. With this set. This is automatically set by the radio.5 WIRELESS IP NETWORK The following contains information and programming instructions for Wireless IP Network.100. In addition. Directed calling functionality is automatically integrated when the radios are configured for wireless IP operation. The radio operator is responsible for choice of channel (frequency) management . however. Bridging is defined as setting the PPP PEER address on the radio equal to the radio’s active wireless IP address. Since all of the PCs are on the 192. These features employ a single channel. The RF-5800M-HH radio offers a wireless IP capability that allows system operators to use IP-based PC software applications. 2 Network Programming The VHF-UHF Radio Programming Application (RPA) is a PC-based program used to configure Harris radios.5.0.100. For Network applications.100.1 RADIO 3 PPP: 10. B-30 .2 V-0234-4200-0019 Figure B-2.2 WIP = Wireless IP Address PPP = Point to Point Protocol Address PC 2 PPP: 192.100.168.168.0.RF NET IP: 192.1 WIP: 192.0 PC 3 PPP: 192. although this feature can also be programmed manually.0.100.X MASK 255.168.3 PC 1 PPP: 192.1 WIP: 192.168.255.0.168.100. General radio programming is outlined in Chapter 4.1 RADIO 1 PPP: 10.100.0.0. See the Network Menu area of Figure B-1 for additional information.3 KEY: RADIO 2 PPP: 10. the RPA is generally used to program the Network settings in the RF-5800M-HH.1 WIP: 192. Basic Wireless IP Network B.100.168.168.255. X (3g Net.X PC 1 LAN1: 172. Telephony) Router 2 VHF PPP: 172.16. WIP.11.16.11.16.10. Example of a Telephony Network B-31 .X (3g Net.11.16.3 LAN 1 172.16.200.2 Local Phone 1 Phone #:1111 RF-6010: LAN1: 172.16.200.1 DG: 172.5 CONNECT TO RADIO PORT 2 HFOUT3 Phone#: 3003 WIP: 172.1 PPP: 172.x HFBASE1 WIP: 172.16.203.200.203.16.2 Ethernet Network Interface HFOUT2 Phone#: 3002 WIP: 172.200.16.16.1.1 PPP: 172.1 HFOUT1 Phone#: 3001 WIP: 172.3 LAN: 172.16.4 CONNECT TO RADIO PORT 1 HFNET1 Net Phone#: 3100 WIP Subnet: 172.10. Telephony) HFOUT4 Phone#: 3004 WIP: 172. WIP.TO PSTN (PUBLIC SWITCHED TELEPHONE NETWORK) PC 5 LAN: 172.16.200.10.16.3 PC 4 PPP: 172.3 HF PPP: 172.200.16.3 Figure B-3.10 Local Phone 2 Phone #:1112 Ethernet Network Interface PPP Network Interfaces LAN 2 172.16.6 HFBASE2 WIP: 172.2 Router 1 LAN1: 172.10.16.10 KEY: WIP = Wireless IP Address PPP = Point to Point Protocol Address LAN = Local Area Network IP Address DG = Default Gateway IP Address HFNET2 Net Phone#: 3200 WIP Subnet: 172.16.16.200.16.11.203.10.16.11.16. Refer to Figure B-4 for the SMS menu tree. SMS can also be used to receive information when a radio is unattended.3.2 to configure the radio for these net types.6 SHORT MESSAGING SERVICE (SMS) SMS provides text-based messaging capability. SMS operation is only available in Directed Calling nets and Wireless IP nets.3 and Paragraph B. B-32 .1 SMS Operation NOTE SMS operation is only available in Directed Calling nets and Wireless IP nets. This feature allows the user to send information using the RF5800M-HH front panel when voice communication is not possible or desirable (as in covert voiceless operations).B.5.6. Refer to Paragraph B. B. SMS Menu Tree B-33 . ONLY AVAILABLE IF A MESSAGE HAS BEEN ENTERED AND LAST ENTERED MESSAGES ARE HELD IN MEMORY ONLY UP TO THE NEXT POWER CYCLE. F-0234-4200-0020 Figure B-4.STU 7OPT SMS NEW SELECT REPLY NEW MSG CANNED MSG (NOTE 1) LAST SENT MSG (NOTE 2) LAST ENTERED MSG (NOTE 3) DELETE ALL MESSAGES? NO YES LAST ENTERED MSG (NOTE 3) PRESS ENT TO SEND MSG DELETE DELETE MESSAGE? NO YES FORWARD PRESS ENT TO SEND MSG DESTINATION BY RADIO ID ALL MESSAGE DESTINATION XXX SEND TO XXX YES NO DELETE_ALL MESSAGE TYPE NEW MSG CANNED MSG (NOTE 1) LAST SENT MSG (NOTE 2) DESTINATION BY RADIO ID ALL MESSAGE DESTINATION XXX SEND TO XXX YES NO NOTES: 1. 3. ONLY AVAILABLE IF A MESSAGE HAS BEEN SENT. ONLY AVAILABLE IF CANNED MESSAGES ARE SAVED IN THE MESSAGE LIST. 2. B.6.1.1 Sending New SMS Messages This procedure describes how to send an SMS message from the radio front panel. B-34 a. Press the [OPT] button. b. Use the left/right arrows to select SMS and press [ENT]. c. Use the left/right arrows to select NEW and press [ENT]. d. If no messages have ever been sent, use the up/down arrows to select either NEW or CANNED. If messages have been sent, use the up/down arrows to select either NEW MSG, CANNED MSG, LAST SENT MSG, or LAST ENTERED MSG. Press [ENT]. e. The message screen will display. If this is a new message, use the keypad to enter the message text. When the message is complete, press [ENT] to continue. f. Use the up/down arrows to select the destination where the message will be sent. Destination can be chosen either by RADIO ID number (to one specific radio) or ALL (to all radios in the net). Press [ENT]. g. If RADIO ID was selected, enter the ID number of the message destination radio to receive the message. Press [ENT]. h. Select YES to confirm the message destination. Press [ENT]. i. The radio will display MESSAGE TRANSMITTED to confirm the message has been sent. B.6.1.2 Forwarding SMS Messages This procedure describes how to forward a received SMS message to another station. a. Press the [OPT] button. b. Use the left/right arrows to select SMS and press [ENT]. c. Use the left/right arrows to choose SELECT, then use the up/down arrows to browse to the received message that will be forwarded. Press [ENT]. d. The message screen will display. Use the left/right arrows to select FORWARD and press [ENT]. e. The message text may be edited or left as displayed. When the message is complete, press [ENT] to continue. f. Use the up/down arrows to select the destination where the message will be sent. Destination can be chosen either by RADIO ID number (to one specific radio) or ALL (to all radios in the net). Press [ENT]. g. If RADIO ID was selected, enter the ID number of the message destination radio to receive the message. Press [ENT]. h. Select YES to confirm the message destination. Press [ENT]. i. The radio will display MESSAGE TRANSMITTED to confirm the message has been sent. B-35 B.6.1.3 Viewing a Received SMS Messages This procedure describes how to view a received SMS message. When a new message is received, it will display for several seconds, and then a flashing M will appear to the right of the Net Number on the main screen. Once the message has been viewed, the flashing M will disappear, but the message is held in memory until deleted by the user. The message can be retrieved as follows: a. Press the [OPT] button. b. Use the left/right arrows to select SMS and press [ENT]. c. Use the up/down arrows to browse through the received messages. The radio can store up to 10 messages. B.6.1.4 Deleting SMS Messages This procedure describes how to delete SMS messages from memory. B-36 a. Press the [OPT] button. b. Use the left/right arrows to select SMS and press [ENT]. c. To delete a single message: • Choose SELECT and use the up/down arrows to browse to the message to be deleted. Press [ENT]. • • Use the left/right arrows to select DELETE and press [ENT]. Select YES to delete the message. Use the up/down arrows to set TEXT PREDICTION.d. If enabled. Press [ENT]. Select YES to delete all SMS messages. Press [ENT]. a. To delete all saved messages: • • B. If enabled. Use the left/right arrows to select SETTINGS. Valid entries are On or Off. Use the up/down arrows to set TONE ALERT to On or Off. Valid entries are On or Off. f. Press the [PGM] button.6. e. g. Press [ENT]. and press [ENT]. Refer to Chapter 4 for general radio programming. d. and press [ENT]. c. Use the left/right arrows to select CFIG. This feature causes entered characters to automatically be set to capital letters. Use the up/down arrows to select the desired CAP MODE. B-37 . Use the left/right arrows to select SMS. h. this feature will automatically “predict” (based upon prior text entries) the letter which displays next when entering a message from the front panel. Valid entries are Insert and Overwrite. Short Message Service Programming This section describes programming the SMS feature from the radio front panel. Use the up/down arrows to select the desired TEXT ENTRY MODE. and press [ENT].2 Use the left/right arrows to select DELETE_ALL and press [ENT]. Press [ENT]. b. a beep sounds when a new message arrives. this feature automatically sends an acknowledgement to the sender when a message arrives. edited or deleted from the front panel. To create a new Canned Message. Messages can be created. Use the left/right arrows to select CANNED. For example. Composing SMS Canned Messages Up to ten messages can be pre-entered and saved for future transmission using the Canned Message feature. d. and press [ENT]. If you want to type the letter O. e. . Using the front panel keypad. and press [ENT]. are accessed by pressing the circular arrow key. press [ENT] to save.2. use the left/right arrows to select Edit. O. When enabled. Press [ENT]. Canned Messages can be up to 160 characters in length. or 5. N. Use the left/right arrows to select CFIG. and press [ENT]. The keys are used to type any of the characters which appear on that key. the 5 key is used to type either M. After a short delay. type the desired canned message.6. Use the left/right arrows to select SMS. including delete and space. rapidly press the 5 key three times until the letter O is displayed.1 Use the up/down arrows to set ACKNOWLEDGE to On or Off. f. When the canned message is composed. The menu of Canned Messages (1.10) displays. Special characters. b. B-38 a. the cursor advances to the next position. B. Press the [PGM] button. c. then use the up/down arrows to select the desired message number and press [ENT].i. g. it can be stored and displayed.Vehicle.B. Falcon Watch™ Sensor Alerts for the RF-5800M-HH consist of text messages and GPS coordinate information received from an RF-5400V-SR Sensor Relay. and transmits alerts when valid events occur. The following sensor data is included in the report: • • • • • Sensor Name (or ID number if no name has been assigned) Detector Type . Refer to the Falcon Watch™ Falcon II System Manual (10515-2801-4200) for complete system operation and programming.Seismic. etc. Tamper . The Falcon Watch™ system utilizes the RF-5400V-SR Sensor Relay node. real-time Situational Awareness. Bearing and Distance to sensor GPS coordinates of sensor B-39 .Indicates an Alert condition was detected from a Sensor detector. The system processes input data from seismic. When an alert is first received by the RF-5800M-HH radio.Indicates battery on the Sensor Relay is low. or Magnetic Target Type .Indicates if one or more of the Sensor Relay tamper indicators was tripped. the RF-5400V-SR broadcasts alert reports to all radios in the net. magnetic.7 FALCON WATCH™ SENSOR ALERTS The Falcon Watch™ system is designed to meet a wide range of challenging surveillance and security needs. Status/Health . multiple detector types. Passive Infrared (PIR). and advanced software to provide true. Using low band VHF frequencies. Personnel. and passive infrared detectors. There are three types of reports that can be received by the RF-5800M-HH: • • • Activity Report . it is recommended that the RF-5800M-HH radio is programmed using Falcon Watch™ Falcon II Mission Programming Application. and operated in the frequency range 30 MHz to 108 MHz.• • Direction Indication (Left-to-Right. This ensures that the radio is programmed with the same RF-6550V VHF-UHF RPA plan file that is used to program the RF-5400V-SR Sensor Node. Direction information for magnetic detectors is always displayed as unknown. • • • Citadel encryption is required. Right-to-Left) Date and Time of alert NOTE Direction information is only displayed if programmed on the RF-5400V-SR sending the sensor event report.7. Sensor Alert Operation When a Sensor Alert message is received at the RF-5800M-HH. Announced with an audible tone (if ALERT TONE is enabled). the net cannot be operated in Plain Text (PT). • The radio net must be either Fixed Frequency/LOS or Quicklook 1A Frequency Hopping. To create a compatible communications net between the RF-5400V-SR and the RF-5800M-HH radio. it is: • • • B-40 Displayed on the radio screen for 30 seconds (if ALERT DISPLAY is enabled). . To ensure reliable communications. B. the following constraints must be considered while programming the radio. Stored in the radio’s internal message log.1 Alert operation is only available in Directed Calling nets and Wireless IP nets. the second Sensor Alert is queued and displayed after the first Sensor Alert message is removed from the display. B-41 . Once removed. the alert message is still stored in memory and can be returned to the display by using the OPT menu. The interrupted Falcon Watch™ message is displayed after all SMS messages have been removed from the display screen. the SMS message (and any subsequent SMS messages) will take precedence over the Falcon Watch™ Sensor Alert message. The flashing A may be removed by viewing the list of stored messages under OPT> ALERTS. and then a flashing A will appear to the right of the Net Number on the main screen. The popup displays will remain for 30 seconds unless CLR is pressed by the user. The Falcon Watch™ Sensor Alert popup message consists of two screens that display the information received from the RF5400V-SR Sensor Node. The list of possible alert messages are shown in Table B-3. If an SMS message arrives while a Falcon Watch™ Sensor Alert message is being displayed. NOTE To avoid SMS message screen display time-outs after 30 seconds the user can scroll between menu options or switch to another screen to retain the message display. Use the up and down arrow keys to shift between the two displays. An alert display will timeout after 30 seconds. See Figure B-5. The alert message is determined by how the RF-5400VSR sensor node is programmed when using the Falcon Watch™ Falcon II Mission Programming Application. or the operator may press CLR to remove it from the display. it will display for 30 seconds. but the message is held in memory until deleted by the user.When a new message is received. If a Sensor Alert message is being displayed when another Sensor Alert message is received. 34 77W 35 .CHARLIE REPORT DIRECTION VEHICLE 2.CHARLIE 34N 27 .78 KM L R NNW DELETE IGNORE BEARING USE UP/DOWN ARROWS TO MOVE BETWEEN SCREENS SENSOR LOCATION COORDINATES ALERT .SENSOR NAME REPORT CLASSIFICATION DISTANCE TO SENSOR ALERT OPERATIONS ALERT . Typical Sensor Report Screens B-42 . 23 18 : 43 : 24 DELETE IGNORE TIME AND DATE OF ALERT V-0234-4200-0025 Figure B-5. Alert Messages Message Unknown Personnel Vehicle Light Vehicle Heavy Vehicle Wheeled Vehicle Tracked Vehicle Airborne Helicopter Propeller Aircraft Jet Aircraft Animal B-43 .Table B-3. the message is removed from the display and deleted from the stored message list. This will fill memory quickly with unnecessary information. The sensor can be temporarily ignored. Select YES to delete the message. use the left/right arrows to select IGNORE and press [ENT].7. With the sensor alert message on the display.7.2. Select YES to ignore all further reports received from the sensor. etc.2 Deleting Alert Messages The Sensor Alert popup messages can be deleted by the operator.1.2 for sensor display status. b.1. in which case. All further messages from the filtered sensor will be ignored (neither displayed nor stored). Use the left/right arrows to select DELETE and press [ENT]. B. all previously stored messages from this sensor that are currently in the radio's list will remain.B. unusual weather conditions. However.7. b. To filter a sensor: a. To delete a single message: B-44 a. which removes the message from the display and deletes it from the stored message list. c. Refer to Paragraph B. .1 Filtering Alert Messages A sensor could transmit multiple false reports under some circumstances such as incorrect sensitivity settings. c. Press [ENT]. Use the up/down arrows to scroll to the desired alert message. c. d. and are saved even if the radio is turned off.1 Reviewing Alert Messages The list of messages currently stored in the radio can be viewed by the operator. Use the left/right arrows to select ALERTS and press [ENT].7. Press the [OPT] button.2. the Sensor Alert message is saved in a list of stored messages. Press [ENT]. Up to 30 alert messages can be stored for viewing. Press [ENT].7.2. Use the left/right arrows to choose DISPLAY_ALL. B-45 . B. Use the left/right arrows to select ALERTS and press [ENT]. they can be returned to normal display operation using the following procedure: a. b. The message screen will be displayed. To select a Sensor Alert message from the list of stored messages and display the message. b. d.2 Display All Alert Messages If messages from a sensor (all sensors in the current net) have been set at the radio as Ignored.7.B. Press the [OPT] button. Use the up/down arrows to select YES to unfilter all messages from the sensor. but those older than the last ten are lost when the radio is turned off.2 Stored Alert Messages Upon reception. Use the left/right arrows to choose SELECT. B. The ten most recent alert messages are stored in non-volatile memory in the radio. perform the following procedure: a. B-46 a. Press [ENT]. . Use the up/down arrows to set ALERT DISPLAY. B. b. d. If ON. Press [ENT].3 Deleting All Alert Messages This procedure describes how to delete Alert messages from memory. Use the left/right arrows to select ALERT and press [ENT]. e. Use the left/right arrows to select ALERTS. and press [ENT]. Press [ENT]. the radio will display incoming alerts for 30 seconds as they are received.7. d. Press [ENT]. a. Press the [PGM] button.B.2. Refer to Chapter 4 for general radio programming. b. Use the up/down arrows to set ALERTS ENABLE. then they will be added to the alert log for future viewing. Use the up/down arrows to select YES to delete all messages saved in memory. Use the left/right arrows to choose DELETE_ALL. Valid entries are ON or OFF. c. and press [ENT].7. this feature will automatically receive and log any incoming messages from the Falcon Watch™ system. Use the left/right arrows to select CFIG. Valid entries are ON or OFF.3 Sensor Alert Programming Perform the following procedure to activate Sensor Alerts from the front panel of the RF-5800M-HH. c. Press the [OPT] button. If ON. B Detector Chan. Tamper Alerts Message Device Movement Detector Chan.5 Low Battery Alert The RF-5400V-SR node will send low battery alerts to the RF-5800M-HH.4 f. A Detector Chan. a beep sounds when a new message arrives. If ON. Table B-4.B. Tamper Alert Reports The RF-5400V-SR node may be programmed to detect tamper conditions and report them to the RF-5800M-HH. B-47 . Possible tamper alert messages that can be displayed on the radio are listed in Table B-4. g. Press [ENT] to accept the setting and return to the ALERTS menu. C Remote Sensor B. Press [CLR] twice to close Programming mode and return to the main operating display. Use the up/down arrows to set ALERT TONE to ON or OFF.7.7. B-48 .This page intentionally left blank. Self-test software that is built into the radio. -CCAM Custom Algorithm Modification or Customer Algorithm Modification or Citadel Algorithm Modification COMSEC Communications Security G-1 .GLOSSARY -AAES Advanced Encryption Standard AM Amplitude Modulation ANC Ancillary ASK Amplitude Shift Keying AUX Auxiliary -BBIT Built-In Test BITE Built-In Test Equipment. .CONTINUED -C. This shows where the next entry from the keypad will be written to the display.Continued G-2 Configuration The process of setting parameter values which define the current hardware setup and/or operational modes. CVSD Continuously Variable Slope Delta. CT Cipher Text CTCSS Continuous Tone Coded Squelch System CTI Computer Telephony Interface Cursor A visible position indicator on the radio's display. a collection of all such values at any given time. Used on wideband digital voice. .GLOSSARY . Also. GLOSSARY . The output may take the form of text. graphics. or a combination of the two. D/V Data/Voice Digital Voice (DV) Analog voice that has been converted into a digital data stream of 1s and 0s. -EECCM Electronic Counter Counter Measures FH Frequency Hopping G-3 .CONTINUED -DDisplay An electronic device which produces visible output (in non-permanent form). 60 MHz is a harmonic of 30 MHz. or provides an area for an operator to input or select data. HCAI Harris Common Air Interface specification.GLOSSARY . Harmonic A frequency that is a whole number multiple of the fundamental frequency .CONTINUED -FField An area on a display that contains operator information. .for example. FM Frequency Modulation FP Front Panel FSK Frequency Shift Keying -GGPS Global Positioning System -H- G-4 Hang Time The length of time after which the radio returns to automatic scan after signal presence is lost on a net. HSIP Harris Session Initiation Protocol used to support RF-6010 to radio functionality..9.Continued Hexadecimal Base 16 numbering structure used in computer systems.F.CONTINUED -H. -IID Identification IP Internet Protocol -J-K-LLi-ION Lithium-Ion LCD Liquid Crystal Display LOS Line of Sight G-5 . Valid characters are 0 . Hold Time The length of time that the radio. after detecting signal presence on a net. will return to automatic scan even if the signal is still present on that net. and A .GLOSSARY . . MIC Microphone MINERR Standard Citadel Mode . MHz Abbreviation for megahertz. RETRANSMIT.The default COMSEC mode supported across all net types: Simple. and Wireless IP. or millions of cycles per second. and KEYPAD LOCK). Directed Calling. Modem Acronym for MOdulator/DEModulator.CONTINUED -M- G-6 Memory A term used to describe the storage internal to the radio. Menu A list of options presented to a user along with some means of selecting one of those options. This is a type of data communications equipment which converts digital signals into an analog format (modulation) suitable for transmission through various media and reconverts received signals into a digital format (demodulation). CLONE.GLOSSARY . MGRS Military Grid Reference System Mode The operational state of the radio as defined by accessing from the [MODE] button (TEST. such as frequencies. frequency.GLOSSARY . etc. Non-volatile data is often retained by means of a battery back-up.CONTINUED -NNet Configuration Data describing a net including name. and transmit power. Non-Volatile Information that is not lost when a unit is turned off. -OOVM Option Validation Matrix -PPA Power Amplifier PC Personal Computer PIR Passive Infrared PT Plain Text PTT Push-to-Talk PPP Point-to-Point Protocol G-7 . squelch. data/voice settings. Net A group of radios that share common communications parameters. predefined set of radio parameters that allows the radio to be set up using only the preset name. RAM Random Access Memory RCV Receive RCVR Receiver RESYNC COMSEC mode that allows a radio on simple voice/data nets (not directed calling or wireless IP nets) to receive an encrypted transmission already in progress. Also see Net Configuration.CONTINUED -Q-R- G-8 Radio Presets A named. RF Radio Frequency RPA Radio Programming Application RS-232 A set of standard specifications for the design of serial ports. An RS-232 port is a serial port which conforms to the EIA standards.GLOSSARY . R/T Receiver-Transmitter . . tone squelch.a type of antenna connector SMS Short Message Service SNR Signal to Noise Ratio Squelch (SQL) The ability to mute the receive audio unless the radio receives the appropriate signal.a type of antenna connector TOD Time-Of-Day TRANSEC Transmission Security TX Transmit G-9 . Can be either digital squelch. or noise squelch.CONTINUED -R.GLOSSARY .Continued RX Receive -SSA Situational Awareness SMB Sub-Miniature B . -TTEK Traffic Encryption Key TNC Threaded N-Connector . This Position Format setting determines how position information is displayed. UTM Universal Transverse Mercator . UTM/UPS Universal Transverse Mercator/Universal Polar Stereographic . G-10 .GLOSSARY . -VVAA Vehicular Adapter Amplifier VAU Vehicular Adapter Unit VHF Very High Frequency VOC Voice Volatile Information that is lost when a unit is turned off.International basis for civil and scientific timekeeping (see Zulu).This Position Format setting determines how position information is displayed.CONTINUED -UUHF Ultra High Frequency UTC Universal Coordinated Time . GLOSSARY . G-11 .CONTINUED -WWBFSK Wideband Frequency Shift Keying -XXCVR Transceiver XMT Transmit XMTR Transmitter -Y-ZZeroize A command sequence which erases all programmed channel parameter and option settings. Zulu Greenwich Mean Time .International basis for civil and scientific timekeeping (see UTC). This page intentionally left blank. G-12 . ........................3-11 Initiating a Directed Call Using a Radio ID ...1-8 Compatible Cables and ConnectorS ....................................................................................A-1 Cipher Text Compatibility ....................................................................................................................B-6...................3-14 Before Operating the RF-5800M-HH ....................................4-24 GPS ...........................................................................................................................................3-29 GPS External Mode .................................................B-7 Introduction ......3-18 Clone Mode ..............4-17 Forced Reporting of GPS/SA Information ................................................4-14 I Initial Tests .......3-44 G GENERAL Programming .....................3-10 INDEX-1 ....................................5-8 B Basic Operation From Net Preset .............................B-9 Disposing of Li-Ion Batteries .......................1-2 Error Messages and Corrective Actions ............................................................1-5 Controls........................................................................3-38 Breaking into a Directed Call ..............2-1 K Keypad Lock ..................B-8 Busy State ............................................................................................. and Connectors ...........................B-11 C CFIG Menu ...........2-6 Battery Life ...............................3-18 Batteries .....................................Connecting the Units ...........................................................................................3-23 F Features .......................................................5-6 Battery Information .........................................................................B-6 Directed Calling Programming ...........................3-47 compatibility .................................................5-6 Battery Storage and Maintenance ....................................................................................................................................................4-12 GENERAL Settings ..................4-12 E ENCKEY Programming ..............1-4 Fixed Frequency Net Programming .3-12 Description ................................. Indicators.....B-28 Frequency Hopping Net Programming .......1-9 Composing SMS Canned Messages ...............................3-44 HOPSET Programming .......................................4-22 Configurations ............................................4-24 Chassis Connector Pinout Data ........4-13 Equipment Description ..............................................................................5-3 Black Digital Retransmit Operation .....................................3-16 BIT Faults .....................................................................3-2 Corrective Maintenance ..............A Attaching a PC to Radio For VHF-UHF RPA Programming ........................................B-26 H Hardware for Retransmission/Repeater Setup ..4-19 Frequency Separation .............B-9 BYPASS Programming ......B-38 COMSEC ........................................................ B-12 Directed Calling ....................................3-1................3-28 CONFIG Programming ................................................................................................................................................................................5-9 Battery Test .................................4-2 Automatic Test .......................................5-2 D Data/Voice (D/V) Settings ................................. B-1 Items Included with the RF-5800M-HH ........................................ .....................................................................................4-12 Number Entry .......................4-10 Locking the Keypad ...........................................4-27 Programming GPS Settings .........................................3-31 Network Programming ..................................... B-9 Net Programming Considerations .................................................................................4-21 Programming Beacon Settings ..................................3-15 N Net Programming .........3-1 Optional Items Available ...........................................................................................................................................................B-9 Radio Lock ................4-10 Select a Net Preset ..........................................................................................................................4-23 Repeater Retransmission Operation ........................................................................................................................................3-8 O Operation Task Summary .......................................................................................B-13 SA Operation ......................................B-30 Non-BIT Faults ........3-19 Level Access ................................4-3 Programming Network IP Settings ......................................................................................................3-36 Security Menu (SECUR) ......Contents of a Net Preset ..........................................4-20 Search and Rescue Beacon Mode ............3-40 Remote Control ...............................................4-16 Net Scanning ....5-1 PRIORITY Programming ...............................................................................4-22 POWER .........3-37 Retransmit Settings .B-14 SA Features ........................................5-7 Red Analog Retransmit Operation .............3-9 Radio Programming Versus Temporary Overrides ..............3-47 Recharging the Li-Ion Battery Packs ........................................................................................................................................................4-28 Programming SMS Settings .........B-14 Safety Precautions .........................................................3-30 LT Button Operation .............4-11 PORTS Menu ..............3-18 ....................................3-12 Optional Version Tests .................................................................3-29 Radio Call Inactivity Timer ......................3-10 Locking the Radio ......................3-23 Selecting PT or CT ..................................................4-28 Programming Task Summary ..........Internal Mode ........3-15 Overview ...................................External Mode ....................................................................................................................B-24 SA Configuration ................3-19 P Password Programming .......3-27 Radio Power-On ..........4-1 Purpose Of This Manual ...........................................................................................................2-5 Optional Manual Tests ........L LCD Display ..........1-1 SAVE .........................Preset Screens .........................3-9 LOCKSET Programming ...4-28 INDEX-2 Programming Menu Tree ...........................4-16...........5-3 NORM Menu ..........3-29 Preventive Maintenance ......3-46 S SA Configuration ......4-21 SCAN Menu .....................................................................................4-27 Programming External Device (EXT_DEV) Settings .....................................1-2 R RADIO .......3-28 Scan List Programming ..............3-9 Radio Options ..............................................................................4-25 Programming Clock Settings ....3-36 REMOTE Port Programming .............................................................4-15 LOCKSETS (Hopping Only) ............................................................................................................................................................................................................3-42 Retransmit Mode .....................................................................................3-24 Receiving Wireless Cloning Information ......... ..................................................................B-29 Transmitting Wireless Cloning Information .....3-11 Unlocking the Radio ............ ............................................ B-35.......................................... 3-30 SPKR .........3-10 Using the External GPS Receiver ..................3-17 Voice/Data Compatibility .B-8 Theory of Operation .......................................................................................................................... B-37................................................B-46 Situational Awareness (SA) ...........................5-3 U Unlocking the Keypad ......B-36............................................... .......Setup Procedure .....................................................................................................B-29 Z Zero Operation ............1-7 W Wireless IP Network ...................3-29..............B-27 Voice/Data and Cipher Text Compatibility ..........3-28 Squelch (SQL) Settings ....................................B-12 SMS ...............................................................................................................3-25 INDEX-3 ......................................................3-49 Troubleshooting Procedures .............B-34....................................................2-10 T Terminating a Directed Call ......................................3-23 System Teardown Procedure ...B-32 Short Messaging Service Programming ...................B-25 V Verifying The Status Of A Wireless Cloning Transfer 3-50 View Data Port Setting .............................................2-9 Short messaging service (SMS) .................4-23 Viewing SA Information ................................................................................................. INDEX-4 .This page intentionally left blank. Fax: 585-242-4755 www. NY USA 14610 Tel: 585-244-5830.com .harris.RF Communications Division ½ 1680 University Ave ½ Rochester.