Diaphr agm Pumps D i a p hr a g m P u m p s Introduction Diaphragm Pump Product Range Operational “Box” for ITT Flojet Diaphragm Pumps (Options below are not available to all ranges) Pressure Open Flow Elastomers Body Materials Switch Range Bypass Range Power 0-160 (0 - 11 bar) 0.3-7 GPM (1.14 - 26.5 LPM) Santoprene, Viton, Buna, Geolast, EPDM, Silicone, Kalrez Polypropylene, Celcon, Nylon 20-160 PSI (1.4 - 11 Bar) or no switch 15-150 PSI (1.0 - 10.4 Bar) or no bypass Electric: 12-48VDC, 110VAC, 230VAC Gas: Air, Co2 or Nitrogen The above defines the box for ITT Flojet’s standard products. As ITT Flojet is also a motor manufacturer we are capable of providing specific solutions to your pumping needs. If the above range is not suitable, please contact the factory to learn about our full range of ITT Flojet Diaphragm Pumps. 160 (11.03) 150 (10.34) 140 (9.65) 130 (8.96) 120 (8.27) Pressure/Head psi (bar) 110 (7.58) 100 (6.89) 90 (6.21) 80 (5.52) 70 (4.83) 60 (4.14) 50 (3.45) 40 (2.76) 30 (2.07) 20 (1.38) 10 (0.69) 0 0 Triplex HI-Pressure - 12, 24VDC and 115, 230VAC Duplex II HI-Pressure 12, 24DC and 115V, 230VAC Low Flow 12 and 24VDC Only Duplex II Low Pressure - 12, 24VDC and 115V, 230VAC Triplex Compact - 12 and 24VDC Only Triplex HI-Flow - 12, 24VDC and 115, 230VAC 5 Chamber 12, 24VDC Quad - 12, 24VDC 115, 230VAC 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) 4.8 (19) 6.5 6.8 7.3 (26) (27) (29) 7.5 (30) Open Flow gpm (lpm) Gas Warning No pump manufactured by ITT should be used for gasoline or any fluid with a flash point below 100º F (38º C) section T HR EE | page 5 0 D i a p hr a g m PUMPS Introduction features and benefits Expect only the best. With over 30 years of pump design and manufacturing experience, ITT Flojet is committed to delivering the hardest working and longest lasting pumps. No matter the application, ITT Flojet can provide a superior pump to match all your requirements. Self-Priming Even When Dry Dry vertical lift from 2.5ft (0.75m) up to an outstanding 27.9ft (8.5m). Can run dry without damage • ITT Flojet diaphragm pumps can run dry for extended periods with no damage even when the liquid supply is exhausted • Compatible with a wide range of chemicals • Seal-less design (no shaft seal, so less leak issues) Compact Size and Lightweight • Highest flow rates for their size • Plug-in ports for easy installation and servicing • ITT Flojet pumps can be mounted easily anywhere with functional mounting platforms and simple connections - fit it anywhere and plumb up Easy, Low-Cost and Convenient Servicing • Modular design • Low cost, low maintenance design means a trouble free service life • Spare parts and accessories are readily available and easy to install The Principal Behind Positive Displacement Diaphragm Pumps Motor Driven Self-priming design allows pumps to create suction to draw fluid into pump without manual priming. Fluid enters inlet port and is drawn through inlet check valve when piston moves away from the check valve. As piston moves toward the check valve assembly, the fluid is forced through the outlet check valve and out of the pump. Air Driven Air pressure directed by the stall-proof shuttle valve pulls the left diaphragm to create suction for the fluid being pumped. Pressurized air is redirected behind the left diaphragm, causing a discharge stroke, forcing the fluid out. At the same time, the right diaphragm draws in more fluid Air is redirected to the right side by the shuttle valve as it repeats the above cycle; forcing fluid out at the right diaphragm and drawing fluid in at the left. s e c t i o n TH REE | page 51 D i a p hr a g m P u m p s Motor Driven LF Series | FOR International & US MARKETS This ultra compact pump uses the duplex diaphragm design to deliver flow and pressure comparable to much larger pumps. FEATURES • Sealed pressure switch automatically starts and stops pump when discharge valve opens and closes • Self-priming so pump can be located above supply tank • Can run dry for extended periods of time without damage • Built-in thermal protector • Low amp draw for battery powered applications OPTIONAL FEATURES • Sealed motor with protective metal cooling finned cover • Integral 5 amp in-line fuse with cover • Manual on/off switch with protective cap to turn off pump when supply tank is empty PERFORMANCE 50 (3.4) 40 (2.8) 30 (2.1) 20 (1.4) 10 (0.7) 0 0 .2 (.75) .4 (1.5) .6 (2.3) .8 (3.0) 1.0 (3.8) Specifications - LF12 and LF11 Series Pump Design Flow Rate Duty Cycle Wetted Parts Reciprocating Diaphragm 1.0 GPM (3.8 L/min) Nominal @ Open Flow Intermittent Pressure/Head psi (bar) Housing Diaphragm Check Valve Check Valve Spring Minimum Tip Size Port Type Operating Pressure Pressure Switch Setting Self-Priming Liquid Temperature Motor Type Motor Voltage Current INST. SHEET #81000-312 Polypropylene Santoprene® Viton® or EPDM 316 Stainless Steel #8 Tip, .072" (1.83 mm) Diameter 3/8" (9.5 mm) Hose Barb 25 PSI (1.7 bar) Maximum 35 PSI (2.4 bar) Off, 25 PSI (1.7 bar) On Up to 2.5 ft (.76 m) Vertically 110° F (43° C) Maximum Permanent Magnet Motor 12 V DC, 24VDC, 115VAC 2.5 Amp Nominal @ 25 PSI (1.7 bar) Flow gpm (lpm) 50 (3.4) 40 (2.8) Pressure/Head psi (bar) 30 (2.1) 20 (1.4) 10 (0.7) 0 0 .2 (.75) .4 (1.5) .6 (2.3) .8 (3.0) 1.0 (3.8) 1.2 (4.5) 1.4 (5.3) 1.6 (6.0) Flow gpm (lpm) section T HR EE | page 5 2 D i a p hr a g m PUMPS Motor Driven LF Series | FOR International & US MARKETS Models Model #s CE Switch PSI (BAR) Bypass PSI (BAR) Voltage Diaphragm Check Valve Open Flow GPM (LPM) comments LF112201 LF112421 LF121421 LF122002 LF122005 RLF122205 LF122201 LF122202 LF122421 LF172201 LF182201 LF221421 LF222005 RLF222205 LF222201 LF222202 LF521401 LF521402 RLF112201 RLF112421 RLF121421 RLF122002 No Yes RLF122201 RLF122202 RLF122421 No No RLF221421 No Yes RLF222201 RLF222202 No No 35 (2.5) 40 (2.8) 40 (2.8) No No 35 (2.5) 35 (2.5) 35 (2.5) 40 (2.8) 35 (2.5) 35 (2.5) 40 (2.8) No 35 (2.5) 35 (2.5) 35 (2.5) 40 (2.8) 40 (2.8) No Yes Yes No No No No No Yes No No Yes No No No No No No 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 24V 24V 24V 24V 24V 115 VAC 115 VAC Santoprene Santoprene Santoprene Santoprene Geolast Geolast Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Geolast Geolast Santoprene Santoprene Santoprene Santoprene Viton Viton Viton EPDM Viton Viton Viton EPDM Viton Viton Viton Viton Viton Viton Viton EPDM Viton EPDM 1.0 (3.8) 1.0 (3.8) 0.7 (2.6) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 0.7 (2.6) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 0.7 (2.6) 0.7 (2.6) Fins, Inline Connector, Inline Fuse, Rocker Switch Fins, Inline Connector, Inline Fuse, Rocker Switch Inline connector Inline connector, Rocker Switch DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 2.38 (61) 1.67 (42) 1.00 (25) 3.19 (81) 3.94 (100) 1.57 (40) 1.66 (42) 6.37 (162) 2.25 (27) s e c t i o n TH REE | page 53 D i a p hr a g m P u m p s Motor Driven DUPLEX II SERIES PUMPS | FOR International & US MARKETS The Duplex II series of pumps incorporate the best technology and features developed by ITT Flojet. Everything from the back flow preventer, check valves, bearings and diaphragm assembly to the motor, have been designed to make this truly the most advanced and reliable diaphragm pump available. Higher efficiency of the pump is evident in the longer life of the motor pump unit. The new diaphragm design combined with the new valves, makes the pump capable of pulling higher dry vacuum. Duplex II is available in various performance ranges, voltages and with a choice of elastomers, making it easily adaptable to a diverse range of applications. FEATURES • • • • • • • Self-priming up to 8 feet (2.4 m) Can run dry without damage Chemically resistant materials Internal bypass standard Built-in back flow preventer Heavy duty ball bearing drive system UL, CSA and CE models available DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. SPECIFICATIONS Pump Flow Rate Pressures Ports Positive Displacement two piston design 2.2 GPM (8.32 L/min) for high pressure models, 1.6 GPM (6.05 L/min) for medium and low pressure models Up to 100 PSI (6.89 bar) 3/8" (9.52mm) NPT female Permanent Magnet with solid state rectifier 12 & 24 V DC, 115 & 230 V AC 50/60 hertz for AC models Up to 8 feet (2.4 M) 15 (1.34), 30(2.07), 45(3.10), 60(4.14), 80, and 100 (6.8) PSI (bar) Polypropylene, Viton®, Buna or EPDM 4 to 5 lbs. (2.28 kgs) 100 PSI (6.8 bar) Demand Pump Demand Pump 9 26) 3.19 (81.026) Motor Voltages 2.25 (57.15) 7.92 (201.168) (61.722) (36.58) 2.43 (57.15) 1.44 (61.722) (36.58) 7.92 (201.168) 3.24 (82.296) 2.25 2.43 1.44 Cycle Dry Vacuum 3.24 Pressure Switch Setting (82.296) 3/8 NPT PORTS 3/8 NPT PORTS Wetted Parts Net Weight 3.63 (92.202) Maximum Operating Pressure 2.02 (51.308) 2.02 (51.308) 3.63 (92.202) .56 (14.224) .56 (14.224) Hi-Pressure INST. SHEET # 81000-339 Low-Pressure INST. SHEET # 81000-338 Bypass Pump Bypass Pump 6) 3.19 (81.026) 2.25 (57.15) 2.43 2.25.72 (61.722) (18.29) (57.15) 2.43 .72 (61.722) (18.29) 3.24 (82.296) 3.24 (82.296) 3.63 (92.202) 2.02 (51.308) .56 (14.224) 3.63 (92.202) 2.02 (51.308) .56 (14.224) section T HR EE | page 5 4 D i a p hr a g m PUMPS Motor Driven DUPLEX II SERIES PUMPS | FOR International & US MARKETS performance Curve 1 ( Curve 2 Curve 3 6 6 Pressure/Head psi (bar) Pressure/Head psi (bar) Pressure/Head psi (bar) Amps (A) Amps (A) 0 (3.0) 0.0 (6.0) 0 (3.0) 0.0 (6.0) 0 (3.0) 0.0 (6.0) Flow Rate gpm (lpm) Flow Rate gpm (lpm) Flow Rate gpm (lpm) Curve 4 Curve 5 Curve 6 Pressure/Head psi (bar) Pressure/Head psi (bar) Pressure/Head psi (bar) Amps (A) Amps (A) 0 (3.0) 0.0 (6.0) 0 (.75) (6.0) 0.0 (7.6) (8.3) 0 (.75) (6.0) 0.0 (7.6) (8.3) Flow Rate gpm (lpm) Flow Rate gpm (lpm) Flow Rate gpm (lpm) * See following pages for specification charts s e c t i o n TH REE | page 55 Amps (A) Amps (A) D i a p hr a g m P u m p s Motor Driven DUPLEX II SERIES PUMPS | FOR International & US MARKETS Models Model #s Model #s CE certified Voltage Switch PSI (BAR) Bypass PSI (BAR) Diaphragm Check Valve Open Flow GPM (LPM) Curve # Comments D2121F5011 D2131F1311 D2131F5011 D2132F5011 D2132I5011 D2135F7011 D21X003 D21X005 D21X007 D3131B1311 D3131B5011 D3131E1311 D3131E5011 D3131I1311 D3131V1311 D3131V5011 D3135B7011 D3135E7011 D71X000 D71X001 D1335E7011 D1625E7012 D1625F7011 D1625H7011 D1631F1311 D1631F5011 D1631H1311 D1631H5011 D1635E7011 D1635F7011 D1635F7021 D3631B1311 D3631B5011 D3631V1311 D3631V5011 D3635B7011 D3835B5011 D2121F5011R D2131F1311R Not Available* D2132F5011R Not Available* D2135F7011R Not Available* Not Available* Not Available* D3131B1311R D3131B5011R D3131E1311R D3131E5011R Not Available* D3131V1311R D3131V5011R D3135B7011R D3135E7011R D71X000R Not Available* Not Available Not Available* Not Available Not Available* Not Available* Not Available* D3631H1311R D3631H5011R D3635E7011R Not Available* Not Available* Not Available* Not Available* Not Available* Not Available* Not Available* Not Available* 12V 12V (24V)** 12V (24V)** 12V 12V 12V (24V)** 12V 12V 12V 12V (24V)** 12V (24V)** 12V (24V)** 12V (24V)** 12V (24V)** 12V (24V)** 12V (24V)** 12V (24V)** 12V (24V)** 12V 12V 36V 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 60 (4.1) No 60 (4.1) 60 (4.1) 60 (4.1) 100 (6.9) No 60 (4.1) No No 60 (4.1) No 60 (4.1) No No 60 (4.1) 100 (6.9) 100 (6.9) No No 100 (6.9) 100 (6.9) 100 (6.9) 100 (6.9) No 60 (4.1) No 60 (4.1) 100 (6.9) 100 (6.9) 100 (6.9) No 60 (4.1) No 60 (4.1) 100 (6.9) 60 (4.1) Yes 50 (3.4) Yes Yes Yes Yes 60 (4.1) Yes 50 (3.4) 50 (3.4) Yes 50 (3.4) Yes 50 (3.4) 50 (3.4) Yes Yes Yes 50 (3.4) 50 (3.4) Yes Yes Yes Yes 50 (3.4) Yes 50 (3.4) Yes Yes Yes Yes 50 (3.4) Yes 50 (3.4) Yes Yes Yes Santoprene Santoprene Santoprene Santoprene BUNA Santoprene Santoprene Santoprene BUNA BUNA BUNA EPDM EPDM BUNA Viton Viton BUNA EPDM BUNA BUNA EPDM EPDM Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene EPDM Santoprene Santoprene BUNA BUNA Viton Viton BUNA BUNA Viton Viton Viton Viton Viton Viton Viton Viton Viton BUNA BUNA EPDM EPDM Viton Viton Viton BUNA EPDM BUNA BUNA EPDM EPDM Viton EPDM Viton Viton EPDM EPDM EPDM Viton Viton BUNA BUNA Viton Viton BUNA BUNA 1.2 (4.6) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 2.1 (8.0) 1.6 (6.1) 2.0 (7.6) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 1.4 (5.3) 1.4 (5.3) 1.4 (5.3) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 2.0 (7.6) 2.0 (7.6) 1 4 3 3 5 3 6 3 3 3 3 3 3 3 3 3 5 5 6 6 5 5 5 5 3 3 3 3 5 5 5 3 3 3 3 5 6 6' (1.83m)cord (Need To Release) Obsolete "J" Models 3/8" (9.52mm) OD JG Discharge Left Heavy Duty Motor Heavy Duty Motor, Discharge Left (NEEDS TO BE RELEASED) Inline Fuse, Rocker Switch Inline Connector, Rocker Switch Inline Connector, Discharge Left Heavy Duty Motor section T HR EE | page 5 6 D i a p hr a g m PUMPS Motor Driven DUPLEX II SERIES PUMPS | FOR International & US MARKETS Models (Continued) Model #s Model #s CE certified Voltage Switch PSI (BAR) Bypass PSI (BAR) Diaphragm Check Valve Open Flow GPM (LPM) Curve # Comments D3835B7011 D3835E7011 D3835H5011 D3835V5011 D4822H4011 D1735J7011RL D3732B1311RL D3732B5011RL D3732H1311RL D3732H5011RL D3732V1311RL D3732V5011RL D3735B7011RL D3735H7011RL D37X006AR Not Available* Not Available* Not Available* Not Available* Not Available* D1735J7011RL D3732B1311RL D3732B5011RL D3732H1311RL D3732H5011RL D3732V1311RL D3732V5011RL D3735B7011RL D3735H7011RL D37X006AR 115VAC 115VAC 115VAC 115VAC 115VAC 230VAC 230VAC 230VAC 230VAC 230VAC 230VAC 230VAC 230VAC 230VAC 230VAC 100 (6.9) 100 (6.9) 60 (4.1) 60 (4.1) 45 (3.1) 100 (6.9) No 60 (4.1) No 60 (4.1) No 60 (4.1) 100 (6.9) 100 (6.9) 60 (4.1) Yes Yes Yes Yes Yes Yes 50 (3.4) Yes 50 (3.4) Yes 50 (3.4) Yes Yes Yes Yes BUNA EPDM Santoprene Viton Santoprene EPDM BUNA BUNA Santoprene Santoprene Viton Viton BUNA Santoprene Santoprene BUNA EPDM EPDM Viton EPDM Viton BUNA BUNA EPDM EPDM Viton Viton BUNA EPDM EPDM 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 1.2 (4.6) 2.0 (7.6) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 1.6 (6.1) 2.0 (7.6) 2.0 (7.6) 1.4 (5.3) 5 5 6 6 1 5 3 3 3 3 3 3 5 5 4 6' (1.83m) cord 6' (1.83m) cord 6' (1.83m) cord 6' (1.83m) cord 6' (1.83m) cord In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression In-line RFI Suppression Induction motor-continuously rated. Available from Europe only * Consult your local ITT Flojet representative **Available in 24V. Consult your local ITT Flojet representative for correct part number s e c t i o n TH REE | page 57 D i a p hr a g m P u m p s Motor Driven triplex compact range | FOR International & US MARKETS The Triplex Compact range pump was designed specifically for the Agricultural market. ITT Flojet’s new three chamber design and versatile features make it ideal for sprayers and many other transfer and dispensing applications. APPLICATIONS This automatic demand pump is fitted • Small Boom and Spot Spraying with a sealed pressure switch and motor, • Foam Marking is self-priming, can run dry, and can be • Silage Treatment installed in compact spaces. • Estate Spraying • Livestock and Poultry Cooling • Dispensing • Transfer of liquids SPECIFICATIONS Pump Design Motor Design Voltage Amp Draw Pump Head Elastomers Diaphragm Motor Operated 3 Chamber diaphragm Permanent Magnet TENV (non-ventillated) 12 VDC 8 amp max for 12 VDC Reinforced Polypropylene Santoprene™ EPDM or Viton 2.0 GPM (7.6 LPM) 60 psi (4.1bar) Intermittent 3.4 lb (1.5 Kg) CE, NSF components 3/8" (9.52mm) NPTF FEATURES • Compact automatic demand pump • Sealed pressure switch and motor • Self-priming; pump can be located above supply tank • Can run dry for extended periods of time without damage • Flow rates to 2.0 GPM (7.6 LPM) and operating pressure to 60 psi (4.1 bar) Check Valve Max. Flow Rate Maximum Pressure Duty Cycle Weight Certifications Port Size Inlet/outlet INST. SHEET #81000-379 performance Curve 1 64 12.0 Curve 2 64 24.0 56 10.5 56 21.0 48 48 18.0 Pressure/Head psi (bar) 40 Pressure/Head psi (bar) 40 15.0 Amps (A) Amps (A) 32 32 12.0 24 24 16 16 8 8 0 (3.0) 0.0 0 .4 (1.5) .8 (3.0) 1.2 (4.5) 1.6 (6.1) 0.0 2.0 (7.6) Flow Rate gpm (lpm) Flow Rate gpm (lpm) section T HR EE | page 5 8 D i a p hr a g m PUMPS Motor Driven triplex compact range | FOR International & US MARKETS Models MODEL #s CE Voltage Switch PSI (BAR) Bypass PSI (BAR) Diaphragm Check Valve Open Flow GPM (LPM) Ports Curve # comments 03501132 03501136 03501142 03501146 03501503 03501505 03501506 03B01132 03B01136 03B01142 03B01146 03501332 03501336 03501342 03501346 03B01332 03B01336 03B01342 03B01346 R3501132 R3501136 R3501142 R3501146 R3501503 R3501505 R3501506 R3B01132 R3B01136 R3B01142 R3B01146 R03501332 R3501336 R3501342 R3501346 R3B01332 R3B01336 R3B01342 R3B01346 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 24V 24V 24V 24V 24V 24V 24V 24V 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) No No No No 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) No No No No Yes Yes Yes Yes Yes Yes Yes 50 (3.4) 50 (3.4) 50 (3.4) 50 (3.4) Yes Yes Yes Yes 50 (3.4) 50 (3.4) 50 (3.4) 50 (3.4) Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Viton Viton EPDM EPDM Viton Viton Viton Viton Viton EPDM EPDM Viton Viton EPDM EPDM Viton Viton EPDM EPDM 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 1.4 (5.7) 2.0 (7.9) 3/8" ((9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 1 2 1 2 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 Rocker Switch, Inline Connector Inline Connector Inline Connector DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 3.60 (91) 8.92 (227) 3.66 (93) 1.90 (48) 3.21 (82) 3.96 (101) 2.95 (75) 2.25 (57) 2.13 (54) s e c t i o n TH REE | page 59 D i a p hr a g m P u m p s Motor Driven Triplex Hi-Pressure Pumps | FOR International & US MARKETS ITT Flojet Triplex Hi-Pressure diaphragm pumps are capable of pressures up to 150 PSI (10.3 Bar), some of the highest pressures available in the diaphragm pump industry. This is ideal for applications such as spraying, misting, filtration, cooling, dispensing and pressure boosting. FEATURES • Constructed from a selection of materials suitable for handling a broad range of chemicals. • Sealed pressure switch and motor • Self-priming up to 8 feet (2.4m); pump can be located above supply tank • Can run dry for extended periods of time without damage • Flow rates to 1.4 GPM (5.5 LPM) and operating pressure to 160 psi (11 bar) APPLICATIONS performance Head-Flow Curve 100 psi Flow Rate 120 (8.4) 110 (7.7) 100 (7.0) 6.0 5.5 PSI (bar) amps 5.0 4.5 4.0 • Designed for wide range of applications • Small Boom and Spot Spraying • Silage Treatment • Estate Spraying • Livestock and Poultry Cooling • Dispensing • Transfer of liquids Pressure/Head psi (bar) 90 (6.3) 80 (5.6) 70 (4.9) 60 (4.2) 50 (3.5) 40 (2.8) 30 (2.1) 20 (1.4) 10 (0.7) 0 .0 .5 (1.9) 1.0 (3.8) 1.5 (5.7) SPECIFICATIONS Pump Design Motor Design Voltage Cycles Amp Draw Pump Head Elastomers Diaphragm Check Valve Max. Flow Rate 6.0 5.5 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Motor Operated 3 Chamber diaphragm Permanent Magnet DC and rectified (PMDC) AC 12, 24 VDC, 115, 230 VAC 50/60 Hz 9 amp max for 12 VDC, 0.95 amp max for 115 VAC Glass filled Nylon Santoprene™ EPDM or Viton 1.4 GPM (5.5LPM) 160 psi (101 bar) switch cutoff 140 psi (9.7 bar) max running pressure 40° F (4° C) Min, 140° F (60° C) Max Intermittent 7.6 lb (3.5 Kg) CE, NSF components 3/8" (9.52mm) NPTF Amps 2.0 (7.6) Flow Rate gpm (lpm) Head-Flow Curve 150 psi Flow Rate 170 (11.9) 160 (11.2) 150 (10.5) 140 (9.8) 130 (9.1) 120 (8.4) 110 (7.7) 100 (7.0) 90 (6.3) 80 (5.6) 70 (4.9) 60 (4.2) 50 (3.5) 40 (2.8) 30 (2.1) 20 (1.4) 10 (0.7) 0 .0 Maximum Pressure Max. Liquid Temp Duty Cycle Weight Certifications Port Size Inlet/outlet INST. SHEET #81000-409 PSI (bar) amps 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Pressure/Head psi (bar) Amps Flow Rate gpm (lpm) .5 (1.9) 1.0 (3.8) 1.5 (5.7) 2.0 (7.6) section T HR EE | page 6 0 D i a p hr a g m PUMPS Motor Driven Triplex Hi-Pressure Pumps | FOR International & US MARKETS Models MODEL#s CE Voltage Switch PSI (BAR) Bypass PSI (BAR) Diaphragm Check Valve Open Flow GPM (LPM) Ports 03711132 03711142 03811132 03811142 03711332 03711342 03811332 03811342 03711032 03711042 03811032 03811042 03711232 03711242 03811232 03811242 R3711132 R3711142 R3811132 R3811142 R3711332 R3711342 R3811332 R3811342 R3711032 R3711042 R3811032 R3811042 R3711232 R3711242 R3811232 R3811242 12V 12V 12V 12V 24V 24V 24V 24V 110VAC 110VAC 110VAC 110VAC 230VAC 230VAC 230VAC 230VAC 100 (6.9) 100 (6.9) 150 (10.5) 150 (10.5) 100 (6.9) 100 (6.9) 150 (10.5) 150 (10.5) 100 (6.9) 100 (6.9) 150 (10.5) 150 (10.5) 100 (6.9) 100 (6.9) 150 (10.5) 150 (10.5) Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes No No Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Viton Viton Viton EPDM Viton EPDM Viton EPDM Viton EPDM Viton EPDM Viton EPDM Viton EPDM 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 1.4 (5.5) 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT 3/8" (9.52mm) NPT DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 150 PSI Model 10.07 (256) 1.62 (41) 3.08 (78) 2.25 (57) 3/8" NPTF 3.60 (91) 3.67 (93) 3.18 (81) 1.9 (48) 9.44 (240) 100 PSI Model 3.93 (100) s e c t i o n TH REE | page 61 D i a p hr a g m P u m p s Motor Driven triplex hi-flow range | FOR International & US MARKETS ITT FLOJET Triplex High Flow Series pumps are designed for a wide range of applications and are constructed from a selection of materials suitable for handling a broad range of chemicals. The Triplex High Flow pumps are self-priming and can run dry without harm. Specifications Pump Design Motor Design Voltages Pump Rating 3 chamber diaphragm Permanent magnet DC 12, 24 VDC, 110VAC, 230VAC IP 54 (splash proof) 5 amps @ 10 psi for 12 VDC 3 amps @ 10 psi for 24 VDC 9 amps @ 10 psi for 12 VDC 6 amps @ 10 psi for 24 VD 9 amps @ 40 psi for 12 VDC 6 amps @ 40 psi for 24 VDC Polypropylene SantopreneTM Viton, EPDM 4 GPM (15.1 LPM) 60 psi (4.1 bar) switch cutoff 50 psi (3.4 bar) max running pressure 40° F (4° C) Min*, 140° F (60° C) Max* Intermittent** 5.05 lbs ( 2.29 kg) max. Standard 18 AWG leads 3/4" (19 mm), 3/8" (9.52 mm) NPTF Amp Draw Pump Head Elastomers Diaphragm Check valves Max. Flow Rate Max. Pressure PERFORMANCE Head-Flow Curve (12 & 24 VDC) Max. Liquid Temp Duty Cycle Weight Wiring Options Port Size inlet / outlet * Consult your local ITT Flojet representative for higher fluid temperature options ** Consult your local ITT Flojet representative for continuous duty application INST. SHEET #81000-417 Pressure/Head psi (bar) Amps flow amp Flow Rate gpm (lpm) section T HR EE | page 6 2 D i a p hr a g m PUMPS Motor Driven triplex hi-flow range | FOR International & US MARKETS Models Model #s CE Voltage Switch PSI (BAR) Bypass PSI (BAR) Diaphragm Check Valve Open Flow GPM (LPM) Motor Size Fittings 03521134 03521139 03521144 03521149 03521334 03521339 03521344 03521349 03521034 03521039 03521044 03521049 03521234 03521239 03521244 03521249 R3521134 R3521139 R3521144 R3521149 R3521334 R3521339 R3521344 R3521349 R3521034 R3521039 R3521044 R3521049 R3521234 R3521239 R3521244 R3521249 12V 12V 12V 12V 24V 24V 24V 24V 110VAC 110VAC 110VAC 110VAC 230VAC 230VAC 230VAC 230VAC 50 (3.4) 60 (4.1) 50 (3.4) 60 (4.1) 50 (3.4) 60 (4.1) 50 (3.4) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) 60 (4.1) Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Viton Viton EPDM EPDM Viton Viton EPDM EPDM Viton Viton EPDM EPDM Viton Viton EPDM EPDM 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 3.0 (11.3) 4.0 (15.1) 2.3" (59mm) Light Duty 3" (76.2mm) 2.3" (59mm) Light Duty 3" (76.2mm) 2.3" (59mm) Light Duty 3" (76.2mm) 2.3" (59mm) Light Duty 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 3" (76.2mm) 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST 1/2" (12.7mm) HB ST DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 4.30 (109) 2.00 (51) 3.98 (101) 4.14 (105) 3.56 (90) 2.00 (51) s e c t i o n TH REE | page 63 D i a p hr a g m P u m p s Motor Driven QUAD 4000 SERIES PUMPS | FOR International & US MARKETS ITT Flojet developed the quad pumps to deliver higher flows up to 5 GPM (18.92 LPM) using a four-piston design with excellent self-priming capability. FEATURES • Built-in pressure switch automatically starts and stops pump instantaneously when discharge valve opens and closes • Compact design and plug-in port fittings make installation easy • Can run dry without damage and handle liquids up to 130° F (54° C) • No metal contact with liquid being pumped • Ball bearing drive throughout pump and motor assures longer pump life • Excellent self-priming capability. Pump may be located above the liquid level • Powerful, permanent magnet motor with low current draw and long life brushes SPECIFICATIONS Flow Rate 3.5 to 5.0 GPM (13.2 and 18.9 LPM) Nominal Diaphragm TEFC/TENV Permanent Magnet Motor 12 & 24 Volt DC, 115 & 230 Volt AC 50/60 hertz for AC Models 1.5 amp max. (115 V) 45 PSI (3.2 bar) cut out 40 PSI (2.8 bar) Up to 8 ft. (2.4 m) Vertical Height Plug-In Ports 1/2" (12.7mm) or 3/4" (19mm) Hose Barb Standard Housing Modified Polypropylene - Standard, Elastomers Santoprene® and Buna - Standard 4 lbs. (2 kg) Pump Design Motor Voltage 3 Cam Pressure/Head psi (bar) performance 12 & 24 Volt DC Cycle Current Pressure Switch Setting * Ideal Operating Range 2 Cam Maximum Operating Pressure Self-Priming Ports * Wetted Parts Net Weight 0 Flow Rate gpm (lpm) *Continuous Duty Max Pressure For No Switch 3 Cam Models *Consult your local ITT Flojet representative for other type of Port Fittings 4300 and I series: INST. SHEET # 81000-084 4100 series: INST. SHEET # 81000-176 AC VSD: INST. SHEET # 81000-388 115 Volt AC DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 3 Cam Pressure/Head psi (bar) * Ideal Operating Range 2 Cam 9.24 (235) 3.06 (78) 0 2.5 (64) 3.75 (95) Flow Rate gpm (lpm) *Continuous Duty Max Pressure For No Switch 3 Cam Models section T HR EE | page 6 4 3.19 (81) D i a p hr a g m PUMPS Motor Driven QUAD 4000 SERIES PUMPS | FOR International & US MARKETS Models Model #s CE Voltage Switch PSI (BAR) Diaphragm Check Valve Open Flow GPM (LPM) Fittings Comments 04100113 04100143 04100505 04300112 04300142 04300143 04300500 04300504 04300506 04300528 04100343 04300342 04300343 04100511 04100500 04100502 04300042 04300043 04300501 04300515 04300525 04300529 04300531 I102010211 I103050211 I301050110 I304010110 R4300538 R4300539 R4320242 R4320243 R4320252 R4320253 No R4100143 No No R4300142 R4300143 R4300500 R4300504 R4300506 No R4100343 R4300342 R4300343 No R4100500 No No No R4300501 No No No No No No No No Yes (see left) Yes (see left) Yes (see left) Yes (see left) Yes (see left) Yes (see left) 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 24V 24V 24V 36V 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 115VAC 230VAC 230VAC 230VAC 230VAC 230VAC 230VAC No No No 45 (3.1) 45 (3.1) 45 (3.1) 45 (3.1) 45 (3.1) 45 (3.1) 45 (3.1) No 45 (3.1) 45 (3.1) No No No 45 (3.1) 45 (3.1) 45 (3.1) 45 (3.1) 45 (3.1) 40 (2.8) 40 (2.8) No No 45 (3.1) 45 (3.1) 35 (2.4) 35 (2.4) 35 (2.4) 35 (2.4) 35 (2.4) 35 (2.4) Geolast Santoprene Santoprene Geolast Santoprene Santoprene Santoprene Santoprene Geolast Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene BUNA EPDM VITON BUNA EPDM EPDM VITON VITON BUNA VITON EPDM EPDM EPDM VITON EPDM VITON EPDM EPDM VITON VITON VITON VITON EPDM VITON EPDM EPDM VITON EPDM EPDM EPDM EPDM VITON VITON 5.0 (19.0) 5.0 (19.0) 3.7 (14.0) 3.7 (14.0) 3.7 (14.0) 5.0 (19.0) 3.7 (14.0) 5.0 (19.0) 5.0 (19.0) 3.8 (14.5) 5.0 (19.0) 3.7 (14.0) 5.0 (19.0) 5.0 (19.0) 3.7 (14.0) 5.0 (19.0) 3.7 (14.0) 5.0 (19.0) 3.7 (14.0) 5.0 (19.0) 5.0 (19.0) 3.0 (11.5) 3.0 (11.5) 5.0 (19.0) 5.0 (19.0) 3.7 (14.0) 3.7 (14.0) 4.5 (17.0) 3.5 (13.0) 3.7 (14.0) 5.0 (19.0) 3.7 (14.0) 5.0 (19.0) 3/4" (14.05 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 1/2" (12.7 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST & GH x 1/2" MNPT 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST + 1/2" HB ELB 3/4" (14.05 mm) HB ST + 1/2" HB ELB 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 1/2" (12.7 mm) HB ST 3/4" (14.05 mm) HB ST 6' (1.83m)cord Cord / Contiuous Duty/Induction motor Cord / Contiuous Duty/Induction motor 6' (1.83m) cord 6' (1.83m) cord 6' (1.83m) cord 6' (1.83m) cord Induction motor/Continuous Duty Induction motor/Continuous Duty Inline connector, Rocker Switch s e c t i o n TH REE | page 65 D i a p hr a g m P u m p s Pentaflex Series | FOR International & US MARKETS ITT Flojet's Pentaflex delivers breakthrough performance for high flow and high pressure applications. These pumps are engineered and constructed of materials suited to handle a broad range of chemicals. The Pentaflex pump self- priming and can run dry for short periods of time. They are designed as duty cycle pump but can run continuously for short periods of time. Typical applications include tranfer, delivery, spraying, cooling, filtration, dispensing, and pressure boosting. EPDM valves with Santoprene diaphragms are available at this time. Additional materials are currently being tested. SPECIFICATIONS Pump Body Pump Design Suction Lift Ports Motor Glass Filled Nylon 5 Chamber Diaphragm Self Priming to 8 ft. (2.5 m) (2) - 3/4” (19 mm) Hose Barb (2) - 3/4” (19 mm) Hose Barb 90° Elbow Permanent Magnet performance (5.5) (4.9) Pressure/Head PSI (BAR) (4.2) (3.4) (2.8) (2.1) (1.4) (0.7) (3.8) (7.6) (11.4) (15.1) (18.9) (22.7) (28.5) (30.3) Models Model #s CE Voltage Switch PSI (BAR) Bypass PSI (BAR) Diaphragm Check Valve Flow Rate LPM (GPM) Open Flow GPM (LPM) Fittings R7300142A R7300342A R7300132A R7300332A Yes Yes Yes Yes 12 24 12 24 80 (5.5) 80 (5.5) 80 (5.5) 80 (5.5) Yes Yes Yes Yes Santoprene Santoprene Santoprene Santoprene EPDM EPDM Vitron Vitron 7.0 (26.5) 7.0 (26.5) 7.0 (26.5) 7.0 (26.5) 3/4" (19.05 mm) HB ST 3/4" (19.05 mm) HB ST 3/4” (19.05 mm) HB ST 3/4” (19.05 mm) HB ST DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 10.15 (25.78) 5.20 (13.20) 4.76 (12.09) 1.97 (5.00) 5.66 (14.38) 3.45 (8.76) 6.25 (15.88) 2.70 (6.86) 5.36 (13.61) 6.11 (15.52) section T HR EE | page 6 6 D i a p hr a g m PUMPS Air Driven n5100 Series | FOR International & US MARKETS ITT Flojet air operated diaphragm pumps offer excellent self-priming capability. Pumps can be located above the supply tank. Suction-side foot valve is recommended for best operation. Liquid pressure is regulated by supply air pressure. No bypass or pressure relief plumbing is necessary. Choice of Santoprene, Buna, or Viton elastomers provide a wide range of chemical compatibility. Quick disconnect liquid and gas port fittings provided for easy installation. FEATURES • Compact design with plug-in hose connections for quick installation • Variety of elastomers to ensure chemical compatibility • Variable capacity from zero to the maximum flow • No pressure relief or bypass plumbing required • Excellent self-priming. Pump may be located above the liquid level SPECIFICATIONS Pump Flow Rate Pressure Ports Wetted Parts Self-Priming Gas/Air Consumption Air-operated positive displacement double diaphragm pump Up to 2.5 GPM (9.5 L/min) 20 to 75 PSI (1.38 to 5.51 bar) Liquid 3/8" (114.3 mm) Air 1/4" (76.2mm) Buna, Santoprene®, Geolast® or Viton® for diaphragms and valves Acetal copolymer for housing 28 ft. (8.5 m) Dry, 32 ft. (9.8 m) Wet Air Supply must be oil-free and dry, 40 PSI at 1 GPM - 0.45 C.F.M., 60 PSI at 1 GPM - 0.58 C.F.M., 80 PSI at 1 GPM - 0.77 C.F.M. Models Model #s CE Diaphragm Check Valve Liquid Fittings INST. SHEET #81000-363 Air Inlet & Air Outlet Max Open Flow GPM (LPM) Comments N5100010 N5100020 N5100040 N5100050 N5100500 Yes Yes Yes Yes Yes BUNA VITON SANTOPRENE GEOLAST SANTOPRENE BUNA VITON SANTOPRENE GEOLAST SANTOPRENE 3/8" HB ST 3/8" HB ST 3/8" HB ST 3/8" HB ST 3/8" HB ST 1/4" HB St 1/4" HB St 1/4" HB St 1/4" HB St 1/4" HB St 2.5 (9.5) 2.5 (9.5) 2.5 (9.5) 2.5 (9.5) 2.5 (9.5) Teflon O-Ring performance 80 (5.5) DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 6.18 (157) 1.98 (50) 1.98 2.22 (50) (56) 6.18 (157) 2.22 (56) Pressure/Head psi (bar) 60 (4.1) 40 (2.8) 20 (1.4) 80* 60* 40* 2.42 (61) 2.42 (61) MODEL : N5100-XXX MODEL : N5100-XXX CO2 OR DRY COMPRESSED AIR OPERATED CO2 OR DRY COMPRESSED AIR OPERATED OPERATING PRESSURE 20 TO 80 PSI OPERATING PRESSURE 20 TO 80 PSI SANTA ANA, CA 92705 2.89 4.14 2.89 4.14 (74) (105) (74) (105) SANTA ANA, CA 92705 0.5 (1.9) 1.0 (3.8) 1.5 (5.7) 2.0 (7.6) 2.5 (9.5) 3.0 (11.4) Flow in gpm (lpm) *Indicates Air Inlet Pressure in PSI 0.77 (19) 0.77 (19) 1.00 (25) 1.00 (25) s e c t i o n TH REE | page 67 D i a p hr a g m P u m p s Air Driven g57 Series | FOR International & US MARKETS Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Chemically resistant Polypropylene body with a choice of Santoprene®, Viton® or Kalrez® elastomers. Quick disconnect liquid and gas port fittings for easy installation. FEATURES • • • • • • • Highest flow rate for any air pump of comparable size Stall proof design with patented shuttle valve Easy installation with all quick disconnect ports Robust design with durable integral mounting Sanitary design with inset molded diaphragm Leak resistant radial seals, no critical O-ring seals Quiet operation with large exhaust muffler SPECIFICATIONS Pump Flow Rate Pressure Ports Air operated positive displacement double diaphragm pump Up to 5 gpm (19 lpm) 20 to 100 PSI (1.38 to 8.27 bar) (Same as inlet air pressure) Liquid 3/8" (114.3mm), 1/2" (152.4mm) and 3/4" (228.6mm) HB Liquid 3/8" (152.4mm) and 1/2" (152.4mm) MNPT Air Inlet 1/4" (76.2mm) HB Polypropylene Santoprene®, Viton® or Kalrez® Santoprene®, Viton®, or Viton Extreme Hasteloy C 1.2 pounds (0.54 kg.) Wetted Parts Body Diaphragm Check Valves Springs Net Weight Santoprene and Viton: INST. SHEET # 82000-014 Kalrez: INST. SHEET # 81000-439 Kalrez® and Viton® Extreme are trademarks or registered trademarks of DuPont Performance Elastomers. performance 1 DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. 3.21 (82) Santropene or Viton Material With 1/2" Ports 3.21 (82) 4.58 (116) 4.58 (116) Pressure/Head psi (bar) 10 0* 80 * 4.52 (115) 60* 4.52 (115) 5.81 (148) 5.81 (148) 5.27 (134) 5.27 (134) 40* 20* 0 Fluid In Fluid In 1.84 (47) Fluid Out 1.84 (47) Air Inlet Fluid Out Air Inlet Flow Rate gpm (lpm) *Indicates Air Inlet Pressure Air Exhaust Muffler Air Exhaust Muffler section T HR EE | page 6 8 D i a p hr a g m PUMPS Air Driven g57 Series | FOR International & US MARKETS Models Model #s Diaphragm Check Valve Liquid Fittings In. (mm) Air Inlet Max Open Flow GPM (LPM) comments G573000 G573205 G573215 G573225 G573145 G573185 G573175 G575005 G575205 G575215 G575225 G575145 G575185 G575175 G57C002 G57C202 G57C203 G57C212 G57C213 G57C222 G57C223 G57C182 G57C172 G57C152 G57C412 Viton Viton Viton Viton Viton Viton Viton Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Santoprene Kalrez Kalrez Kalrez Kalrez Kalrez Kalrez Kalrez Kalrez Kalrez Kalrez Kalrez Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene NONE 1/2-3/8" HB ST (10-13mm) 1/2" HB ST (12.7) 3/4" HB ST (19) 1/2" OD JG (12.7) 3/8" MNPT ST (9.5) 1/2" MNPT ST (12.7) NONE 3/8" HB ST (10/13 mm) 1/2" HB ST (12.7) 3/4" HB ST (19) 1/2" OD JG (12.7) 3/8" MNPT ST (9.5) 1/2" MNPT ST (12.7) NONE 1/2-3/8" HB ST (10-13mm) 1/2-3/8" HB ST (10-13mm) 1/2" HB ST (12.7) 1/2" HB ST (12.7) 3/4" HB ST (19) 3/4" HB ST (19) 3/8" MNPT ST (9.5) 1/2" MNPT ST (12.7) 3/8" OD JG (9.5) 1/2" OD JG (12.7) NONE 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB EL Brass 1/4" HB Brass 1/4" HB EL Brass 1/4" HB Brass 1/4" HB EL Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 1/4" HB Brass 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) 5.0 (19.0) s e c t i o n TH REE | page 69 D i a p hr a g m P u m p s Air Driven G57 Series Dual High FloW | FOR International & US MARKETS Features • Flows to 10 GPM (38 L/min) • Chemically resistant Polypropylene housings with Viton and Santoprene elastomers • Easy installation with 1/2¡± (12.7 mm) Dual and 3/4¡± (19.1 mm) Quatro pump manifolds • Duplex diaphragm design • Patented shuttle valves eliminates stalling • Compact size Specifications Pump Design Flow Rate (Dual) Operating Pressure Liquid Inlet Pressure Liquid Temperature Priming Air Supply Pressure Noise INST. SHEET #81000-354 Positive Displacement Double Diaphragm Up to 10.0 GPM (37.8 LPM) 20 to 100 PSI (1.4 to 6.0 bar) 30 PSI (2.1 bar) Max. Min. 40° F (4.4° C), Max. 140° F (60.0° C) Dry 15ft (4.5 m), Wet 20ft (6.1 m) 20 to 100 PSI (1.4 to 6.9 bar) Max 90 dB Models Model #s CE Diaphragm Check Valve Liquid Fittings in. (mm) Air Inlet IN. (mm) Max Open Flow GPM (LPM) comments G257301A G257302A G257501A G257502A G577000A G578000A Yes Yes Yes Yes Yes Yes VITON VITON SANTOPRENE SANTOPRENE SANTOPRENE VITON POLYPRO POLYPRO POLYPRO POLYPRO POLYPRO POLYPRO 1/2" NPTF (12.7) 1/2" NPTF (12.7) 1/2" NPTF (12.7) 1/2" NPTF (12.7) NONE NONE 1/4" HB ST (6.4) 1/4" QD EL (6.4) 1/4" HB ST (6.4) 1/4" QD EL (6.4) NONE NONE 10.0 (38.0) 10.0 (38.0) 10.0 (38.0) 10.0 (38.0) 5.0 (19.0) 5.0 (19.0) Santoprene reverse flow for dual G57 Viton reverse flow for dual G57 10.06 (256) performance Dual (10 GPM) (Model G257XXX) DIMENSIONAL DRAWING 5.19 (MAX) (127) (MAX) 10.06 (256) Unless otherwise stated dimensions in [ ] are in mm. 5.19 (MAX) (127) (MAX) 100 (6.9) 100* Pressure/Head psi (bar) 80 (5.5) 60 (4.1) 40 (2.8) 20 (1.4) 80* 12.88 (328) 12.88 (328) 5.84 (148) 12.88 (328) 60* 40* 5.19 (MAX) (127) (MAX) 5.19 (MAX) (127) (MAX) 5.0 (18.9) 10.0 (37.8) 20.0 (75.5) 10.06 (256) 0.84 (21) 20* 10.06 (256) 5.84 (148) 12.88 (328) 0 12.88 Flow Rate gpm (lpm) (328) *Indicates Air Inlet Pressure 12.88 (328) 5.84 (148) section T HR EE | page 7 0 D i a p hr a g m PUMPS Air Driven PERMANENT MAGNET MOTORS | FOR International & US MARKETS ITT Flojet manufactures a wide range of 3” (76.2mm) diameter permanent magnet motors. These are designed as a more cost-effective alternative to larger series wound or induction type motors. They also offer flexibility of speed in the range of 1000 to 5000 rpm. Low heat rise and high efficiency ensures long and reliable service life. The ease with which these motors can be adapted to any application is enhanced by the availability of various motor lengths and shaft configurations. The fact that the motors are bidirectional increases their versatility. Most of our motors have the appropriate agency approvals including UL, CSA and CE. FEATURES • Highly efficient permanent magnet design • Combines advantages of low amp draw heat rise with high torque and low speed • Diamond-turned commutator • Delivers up to 1/8 H.P. in compact 3" (76.2mm) diameter • 6, 12, 24, 32, 36, 115, 230 and 240 volt AC or DC • Lightweight double insulated armatures • High starting torque - up to 600% of rated torque • Speed control capability • Available with internal solid state rectifier (AC models only) • Instant reversibility (DC voltages) • Thermo protection available • Dynamic braking capability • UL recognized (115 Volt AC models only) • Partial or full suppression available with CE certification motor shaft configuration SPECIFICATIONS Motor Design Permanent Magnet Size 3 in. (76.1 mm) Diameter Totally Enclosed (TENV) Stack Length 1/2 in. - 2 in. (12.7 - 50.8 mm) Horsepower Duty Speed Voltage Insulation Up to 1/40 - 1/8 1H.P. Continuous or Intermittent 1100-5000 R.P.M. 6-230 Volt DC or Rectified AC Class B Standard Sleeve or Ball Bearing Totally Enclosed / Totally Enclosed Fan-Cooled 2.31 BC (58.7) 2 62 DIA 2.62 (xx) (66.5) 3.00 DIA (76.2) L DIMENSIONAL DRAWING Unless otherwise stated dimensions in [ ] are in mm. Bearings Enclosure Totally Enclosed (TENV) Totally Enclosed (TENV) L1 L1 Fan Cooled (TEFC) 1.12 (28.4) 2 62 DIA 2.62 (xx) (66.5) 2 62 DIA 2.62 3.00 (xx) DIA (66.5) (76.2) 3.00 DIA (76.2) 3.37 DIA (85.6) Fan Cooled (TEFC) Stack Lg.1.12 (approx) Fan IN.Cooled (MM) (TEFC) (28.4) 0.5 (12.7) 0.875 (22.2 ) 3.37 1.25 DIA(31.8) (85.6) 3.37 DIA 1.875(85.6) (4.6) 1.12 (28.4) A IN. (MM) 2.87 (72.9) 3.25 (82.6) 3.7 (94) 4.4 (111.8) MHP 20 50 75 100 2.31 BC (58.7) 2.31 BC (58.7) s e c t i o n TH REE | page 71 A cc e s s o r i e s | F i t t i n g s 1720/1740/1745 SERIES inlet strainers | FOR International & US MARKETS Features • Low profile design for space saving installation. • Very strong reinforced plastic base with clear cover. • Wide variety of port configurations from 3/4" (19.4=1mm) to 3/8" (9.5mm). SPECIFICATIONS Materials Base Cover Screen O-rings Polypropylene, black Polysulfane, smoke tinted Stainless Steel, 20 and 40 mesh Polypropylene Screen, 20 mesh Buna-N FDA Compound 3/8" npt (9.5mm) quad port Temperature Dimensions 160°F (70°C) max. 2.75" (70 mm) diameter x 2.25" (57 mm) high 4.75" (121 mm) max. port to port (3/4" hose barb) Plug-in style, 3.75" (96 mm) max. length INST. SHEET #12345-000 Models Model # Description 01720-000 01720-002 01720-023 3/8" Hose Barb (9.5mm) 1/2" Hose Barb (12.7mm) 3/4" Hose Barb (19.0 mm) 1/2" Hose Barb (12.7mm) (Plugs into Quad pump port) 3/4" (19.0mm) x 3/4" (19.0mm) hose barb SS 20m 1/2" (12.7mm) x 1/2" (12.7mm) hose barb SS 20m 3/8" (9.5mm) hb x 3/8" (9.5mm) NPT (m) 90° SS 20m 1/2" (12.7mm) x 1/2" (12.7mm) hose barb PP 20m 3/8" (9.5mm) x 3/8" (9.5mm) hose barb PP 20m 1/2" (12.7mm) x Quad port 90° PP 20m 3/8" (9.5mm) hb x 3/8" (9.5mm) NPT (m) 90° PP 20m 3/8" (9.5mm) NPT(f) x 3/8" (9.5mm) NPT(f) SS 20m 3/4" (19.0mm) x 3/4" (19.0mm) hose barb SS 40m 1/2" (12.7mm) x 1/2" (12.7mm) hose barb SS 40m 3/8" (9.5mm) x 3/8" (9.5mm) hose barb SS 40m 1/2" (12.7mm) x 1/2" (12.7mm) SS 40m 3/4" (19.0mm) x Quad port 90° SS 40m 1/2" (12.7mm) x Quad port 90° SS 40m 1/2" (12.7mm) x Quad port 90° SS 40m 3/8" (9.5mm) NPT(f) x 3/8" (9.5mm) NPT(f) SS 40m Strainer In-line 3/4" (19.0mm) HB X 3/4" (19.0mm) HB SS 40M PETG VIT Strainer In-line 3/4" (19.0mm) HB X QUAD PORT 90˚ 40M PETG VIT Strainer In-Line 1/2" (12.7mm) HB X QUAD PORT 90˚ 40M PETG VIT Strainer In-Line 3/8" (9.5mm) HB X 3/8" (9.5mm) MNPT SS 40M PETG VIT PP - Polypropylene m - Mesh 01720-102 01720-103 01720-112 01720-123 01720-375 01740-000 01740-002 01740-003 01740-004 01740-010 01740-012 01740-014 01740-375 017450-00S Inlet Strainer 3/8" Hose Barb (9.5mm) 1/2" Hose Barb (12.7mm) 3/4" Hose Barb (19.0 mm) 1/2" Hose Barb (12.7mm) 017450-10S 017450-12S 017450- 23S SS - Stainless Steel In-line Strainer section T HR EE | page 7 2 3/8" NPT (9.5mm) Accessories | Fit tings ELECTRIC PUMP FITTINGS | FOR International & US MARKETS Nylon Barbed Straight/Elbow For use with all Duplex II Series Pumps (3/8" (9.5mm) NPT only). MODELS Part # Straight Part # Elbow Description 91010-032 91010-004 91010-002 91010-034 91010-006 91010-053 91006-477A 91010-033 91010-003 91010-001 91010-025 91010-005 91010-052 N/A 3/8" (9.5mm) NPT Male x 1/4" (6.4mm) Barb 1/4" (6.4mm) NPT Male x 3/8" (9.5mm) Barb 3/8" (9.5mm) NPT Male x 3/8" (9.5mm) Barb 1/4" (6.4mm) NPT Male x 3/8" (12.7mm) Barb 3/8" (9.5mm) NPT Male x 1/2" (6.4mm) Barb 1/4" (6.4mm) NPT Male x 1/4" (6.4mm) Barb Wire Harness 9' (2.74m) with fuse rocker switch and inline connector Plastic (Polypropylene, EPDM)* Inlets & Outlets For use with all Quad and G57 Series Pumps MODELS Part # Straight Part # Elbow Description 20381-000 20381-002 20381-006 20381-007 20381-008 20381-009 20381-010 N/A Quad Port x 1/2"-14 Male Straight Quad Port x 1/2" Hose Barb Quad Port x 3/4" Hose Barb Quad Port x Garden Hose Adapter **Packaged 2 per bag *Other Elastomers Available GAS PUMP FITTINGS Stainless Steel Inlets & Outlets (Liquid Fittings) For use with all 5100 Series Pumps MODELS Part # Straight Part # Elbow Description 20324-030 20325-030 20606-100 20607-100 20608-100 N/A 1/4" (6.4mm) Hose Barb 3/8" (9.5mm) Hose Barb 1/2" (12.7 mm) Hose Barb Brass CO2/Air Inlets with Shut-off Valve (Air Fittings) For use with all 5100 and G Series Pumps MODELS Part #s Description 1510-000 1520-000 1521-000 1/4" (6.4mm) Hose Barb, Straight 1/4" (6.4mm) Hose Barb, Tee 1/4" (6.4mm) Hose Barb, Elbow Plastic (Celcon) CO2/Air Inlets For use with all 5100 and G Series Pumps MODELS Part #s Description 20325-033 1/4" (6.4mm) Hose Barb, Straight s e c t i o n TH REE | page 73 s a n i ta r y d i a p hr a g m P u m p s Sanitary Diaphragm Pumps section T HR EE | page 7 4 s a n i ta r y d i a p hr a g m P u m p s SUPER HYGIENIC Pureflo® 21 Super Hygienic Diaphragm Pump FOR International & US MARKETS ITT Jabsco’s Pureflo 4-piston diaphragm pump is designed to be used in pharmaceutical, biotech, food or cosmetic applications. The design complies with the stringent requirements of these industries. The pump and controls are mounted in a stainless steel cabinet. The system can be cleaned easily and the simple construction allows safe and easy use. Specifications Drive Motor Motor protection Variable speed Torque Motor power Electrical Details Power supply Intelligent controls enable operation at most single phase supplies, 115-240 V AC, 50 or 60 Hz 24 V DC Touch Pad 1 - 100 % nof speed 24 V DC IP 54 0 - 3,000 rpm 0.42 Nm at 3,000 rpm 132 Watt, 8.7 Amp Features • Bench top complete unit • Fixed or variable speed AC unit • Easy to clean, no shaft seals • Can run dry • Low noise, constant flow • Compact and small • Adjustable flow up to 365 gph (1,380 lph) • Pressure up to 87psi (6.0 bar), in constant use 72 psi (5.0 bar) should not be exceeded • Temperature up to 140° F (60° C) in constant use, CIP up to 194°F (90° C) and SIP 275° F (135° C) is possible • Viscosity up to 250 Centipoise • Unit supplied with 3.1B material certificates • SIP Capabilities Controls voltage Programmable Controls Materials / Surfaces Parts in contact with fluid are manufactured from FDA conforming materials only. Surface finish Ra < 0.8 µ standard (32 micro inch), 0.5 µ (20 micro inch) and electro polish is available on request. Parts in Contact with Fluid Head Diaphragm Valves / O-Ring Valve chamber & pistons Ports Stainless Steel 316L Santoprene EPDM / Buna Polypropylene Tri-Clamp 3/4” (19mm) 5 1 2 3 4 Technical and Construction Details 1. Low carbon 316L pump head for reduced carbide precipitation, increased corrosion resistance and minimal carbon pullout. 2. Chemical resistant Polypropylene valve chamber and piston guarantees long-life of the system. 3. Hygienic Santoprene® diaphragm conforms to FDA requirements. 4. Non-contact cam assembly ensures super hygienic standards are maintained. 5. Valves in EPDM for optimum chemical resistance capability. Model Port Size Pureflo 21 (inch) Tri-Clamp 3/4 (mm) 19 6 87 Max Flow (per min) (GPM) Max Pressure Max Speed Size LxBxH Weight (psi) (LPM) 23 (bar) 6 (RPM) 3000 (inch) 15x15x11.75 (mm) 380x385x300 (lbs) 43 (kg) 19.5 Max Operating Temp (°F) +140 (CIP 194) (°C) +60 (CIP 90) Viscosity (cP) 250 s e c t i o n TH REE | page 75 D ru m Pu m p s Drum Pump motor | FOR International & US MARKETS Heavy duty motor has extra large handle for work with gloved hands. 20ft (6.09m) power cord with grounded three prong plug. Power switch guard prevents inadvertent operation. Built-in circuit breaker is reset by toggling the power switch to off, then on. Optional Low Voltage Safety Shut-Off (LV) sets motor to “OFF“ if power is lost. Motor will not turn on unexpectedly if power is restored after a power failure. Toggle power switch to restore normal operation. Self-aligning motor coupling makes pump tube easy to attach. Optional CE. Applications • Transfer from drums carboys and IBC’s aggressive liquids, acids, solvents and food products. • Rugged construction pump tubes in four material options. Specifications Motor Type Motor Brushes Nominal Amp Draw Duty Cycle 115V AC and 220V AC 50/60 Hz 600 Watts fan cooled, thermal protection Replaceable 5.8 amps for 115V AC models 3.0 amps for 230V AC models Intermittent CE some models Weather protected 40-120˚F (4-53˚C) 7.5 lbs (3.4 kg) ACCESSORIES Approvals Enclosure Model 18753-0077 (US) Model 23510-0010 (International) Chemically resistant plastic adjustable nozzle Model 16471-0000 (US) Safety Ground Strap Model 16470-0000 (US) Model 23500-0000B (International) Wall Mount Drum Pump Storage Bracket for easy storage when pump is not in use Model 16490-1000 (US) Polypro Strainer - Gray Model 16490-1001 Tefzel Strainer - Black Blocks debris entry and protects pump impeller Model 18753-0080 (US) Model 23505-0000B (International) Drum Pump Bung Adapter 2" (50.8mm) allows pump tube to fit snugly in 2" (50.8mm) bung hole Ambient Temperature Wt. Models Model #S Ce Power Options Plug 16450-0115 16450-1115 16450-2115 16450-0220 16450-3220 16450-2220 16450-4115 Yes Yes Yes Yes Yes Yes Yes 115V AC 60 Hz 01 115V AC 60 Hz 01 115V AC 60 Hz 01 230V AC 50/60 Hz 01 230V AC 50/60 Hz 01 230V AC 50/60 Hz 01 115V AC 60 Hz 01 CB CB, LV CB, LV, CE CB CB, LV, CE CB, LV, CE CB, LV US US US None Euro UK None Drum Pumps Gas Warning No pump manufactured by ITT should be used for gasoline or any fluid with a flash point below 100º F (38º C) section FOU R | page 77 D ru m Pu m p s Centrifugal Pumps Drum Pump Air Motor | FOR International & US MARKETS Specifically designed to fit ITT Jabsco drum pump tubes. Do not use where flammable vapors are present. Always use safety ground strap. PERFORMANCE 80 (24.38) 30 (2.1) Specifications Supply Motor Housing PSI (BAR) Clean dry air, 15 CFM (4.6 CMM) at 80 psi (5.5 bar) 90 psi (6.2 bar)maximum inlet air pressure .36 HP at 8,000 RPM Cast iron body Cast aluminum end plates and adapter Bronze 1/4 turn ball valve 1/8" (3.2 mm) NPT (F) inlet Spun Wire Exhaust Muffler 40-120˚F (4-53˚C) 5 1/8" x 1 3/4" x 5 3/4" (129 x 45 x 146mm) 1.8 lbs (.8 kg) 16440-0000 Feet (Meters) of Water 60 (18.28) 16450 Electric Motor 25 (1.7) 20 (1.4) 15 (1.03) 10 (.69) 40 (12.19) Air Inlet Valve Air Outlet Temperature Size Ship Wt. Model # 20 (6.09) 16440 Air Motor 5 (.34) 0 0 0 5 10 15 20 25 (18.32) (37.85) (56.78) (75.70) (94.63) Flow Rate GPM (LPM) Drum Pump Tubes | FOR International & US MARKETS ITT Jabsco pump tubes easily handle a wide range of chemicals from strong acids and caustics to severe solvents and oils. Kynar is our most chemically resistant drum pump tube material. Hygienic models handle food and beverage grade liquids and are built with USDA approved materials. Select drum pump tube length and materials compatible with the container and fluid being pumped. Not recommended for viscosities over 3500 SSU. Sealless pump design provides up to 30 minutes of run dry operation. Specifications Pump Tubes 16400-3350 (US Only) 16400-3270 16400-3400 16400-3470 16410-3350 (US Only) 16410-3270 16410-3400 16410-3470 16510-3350 (US Only) 16510-3270 (US Only) 16510-3400 (US Only) 16510-3470 (US Only) 16520-3350 (US Only) 16520-3270 16520-3400 16520-3470 Tube Material Polypropylene Polypropylene Polypropylene Polypropylene Stainless Steel Stainless Steel Stainless Steel Stainless Steel Hygienic SS Hygienic SS Hygienic SS Hygienic SS Kynar Kynar Kynar Kynar Length in IN (M) 35.5 (0.9) 27.0 (0.7) 40.0 (1.0) 47.0 (1.2) 35.5 (0.9) 27.0 (0.7) 40.0 (1.0) 47.0 (1.2) 35.5 (0.9) 27.0 (0.7) 40.0 (1.0) 47.0 (1.2) 35.5 (0.9) 27.0 (0.7) 40.0 (1.0) 40.0 (1.0) Shaft Carpenter Carpenter Carpenter Carpenter 316 SS 316 SS 316 SS 316 SS Hygienic Hygienic Hygienic Hygienic Hastelloy Hastelloy Hastelloy Hastelloy Impeller 20 Tefzel 20 Tefzel 20 Tefzel 20 Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Tefzel Weight in LB (KG) 2.25 (1.02) 2.25 (1.02) 2.25 (1.02) 2.25 (1.02) 7.5 (3.4) 7.5 (3.4) 7.5 (3.4) 7.5 (3.4) 7.5 (3.4) 7.5 (3.4) 7.5 (3.4) 7.5 (3.4) 2.75 (1.25) 2.75 (1.25) 2.75 (1.25) 2.75 (1.25) Container Drums (US) Carboys Drums (Euro) Large Vats Drums (US) Carboys Drums (Euro) Large Vats Drums (US) Carboys Drums (Euro) Large Vats Drums (US) Carboys Drums (Euro) Large Vats *For chemical compatibility see data sheet SD932 section F OUR | pa g e 7 8 *See page 60 for additional specs and dimensions Flexible Impellers