. Goa. it is the user’s responsibility to determine the suitability for his own use of the products described herein. expressed or implied. India .mail [email protected] +91 (0832) 3981100 fax +91 (0832) 3981101 .CATHODIC PROTECTION Oxygen & Specialties LIDA® Piggy Back wire Anode LIDA® (MMO) WIRE ANODE ( 3 mm Ø) For Cathodic protection of Mounded of LPG Storage Bullets and Tank Bottoms Description: Application: LIDA® MMO Wire anode (3 mm dia) assembled Piggy-back on XLPE/PVC 10 mm2 cable. ADVANTAGES: • Low linear resistivity. LIDA® MMO Wire anode (3 mm dia) is used for Cathodic Protection of mounded LPG storage bullets and tank bottoms. • High quality and QC on connections (Helium leak test at 2 atm and Conductivity check performed on each joint).185 & 189.com Durantes Vincunt De Nora India Limited . SPECIFICATIONS: Tank Bottoms WIRE SPECIFICATION Current Rating in sand Current Density in sand Dimensions (dia) Design Life (years) Base Metal Catalyst composition UNIT UNIT mA/mtr. complete with cable to anode joint using splice encapsulation kit.www.Kundaim .5 mm Ø) For Cathodic protection of Pipelines Description: Application: Underground Pipeline LIDA® MMO Wire anode (1. • No need to spot welding on site.denora.75 A/m2 8 mm 3 30 Titanium Precious mixed metal oxide (MMO) Coating mA/mtr. Nothing herein contained is to be construed as a recommendation to infringe any patent.Plot No. Since the actual use by others is beyond our control.5 A/m2 8 mm 1. Lida® Piggy Back Wire Anode LIDA® (MMO) WIRE ANODE ( 1. • Easy to handle and install.com . 184. Kundaim Industrial Estate . LIDA® MMO Wire anode (1. is made by De Nora as to the effects of such use or the results to be obtained. 37. • Assembled in the factory.5 30 Titanium Precious mixed metal oxide (MMO) Coating 10mm2. XLPE/PVC 10mm2. In addition. recommendations and suggestions appearing herein concerning the use of our products are based upon tests and data believed to be reliable. DNI 002_Lida Piggy-Back wire 8_09 Crimping and sealing with mastic and Heat Shrink Sleeve . nor does De Nora assume any liability arising out of the use by others of the products referred to herein. complete with cable to anode joint using splice encapsulation kit. the information herein is not to be construed as absolutely complete since additional information may be necessary or desirable when particular circumstances exist or because of applicable laws or government regulations.com All information.5 mm dia) assembled Piggy-back on XLPE/PVC 10 mm2 cable. no guarantee. However.5 mm dia) is used for Cathodic Protection of poorly coated pipelines as well as for hot spot protection.denoraindia.403 115. XLPE/PVC CABLE LPG Mounded bullet Cable type JOINT DE NORA www. 18 0.5 x 50 XL 2. freshwater. the tubular dimensions remain nearly constant during the life of the anode — providing a consistently low resistance anode. 30 25 20 15 10 5 0 0 5 10 15 20 25 30 35 40 45 50 APPLICATIONS • Groundbeds Deep Shallow Vertical Horizontal Open Hole • Marine Sea Water Brackish Water Mud • Fresh Water FEATURES • • • • • Multi-anode conductor Lightweight / durable High current output Patented crimp connections Dimensionally stable BENEFITS • Dramatically reduces cable costs • Reduces handling and installation costs • Lower cost per amp-hr • Guaranteed electrical contact and moisture seal integrity • Consistently low resistance anode Life.5 x 100 XL 2. 1 20134 Milano.com Protech Business Unit LIDA® tubular anodes are titanium tubes with a mixed metal oxide coating.5 x 100 XXL Dimensions: Anode Diameter cm inches Length cm inches Weight kg lbs Surface Area m2 ft2 2. mud. measured in terms of milligrams per ampere-year.00 50 19.5 x 100 XXL are designed for extended life operation. Italy ph: +39 02 2129 2722 fax: +39 02 2129 2801 LIDA Tubular Anodes ® www.5 1. As a result of this low consumption rate. .5 x 100 2.7 0.40 0.5 1. The mixed metal oxide is a crystalline. or seawater.35 0. LIDA® mixed metal oxide coatings demonstrate very high chemical stability — even in environments with very low pH values.00 100 39.CATHODIC Protection Via dei Canzi.84 LIDA® tubular 2.039 0. years 2. Unlike other impressed current anodes. years LIDA® Tubular Anode Life in Fresh Water 50 Anode Current.4 0. the LIDA® coatings are not affected by the generation of chlorine. electricallyconductive coating that activates the titanium and enables it to function as an anode.5 x 50 2. amps 45 40 35 Whether operating in soil.079 0. amps 80 70 60 50 40 30 20 10 0 0 5 10 15 20 25 30 35 40 45 50 Life.lidaproducts.42 2. Please contact us when operation is expected in waters below 5˚ C.77 0. LIDA® Tubular Anode The mixed metal oxide anode has an extremely low consumption rate. Maximum Current for LIDA® Tubular Anodes (life in years) LIDA® Tubular Anode Life in Sea Water 90 Anode Current. the crimp on the ends and in the middle appears the same. conductive. 1. the junction box is eliminated when using a LIDA® string — reducing the cost of materials and labor.5 3.CATHODIC Protection LIDA® Tubular Anodes A LIDA® “anode string” is comprised of electrical cable threaded through one or more tubular anodes.5 x 100 XL 2.S. Via dei Canzi. Electrical connection between the tubular anode and the power cable wire is achieved by sliding the tube onto the cable and crimping a section of the tube at mid-length around a stripped portion of the cable. Design. On the surface.5 x 100 XXL 0. 2. Both ends of the tubular anode are sealed over the insulated cable by applying 50 tons of hydraulic pressure. good design practices. 1. which may develop cracks or lose adhesion to the cable or the anode. it is the user’s responsibility to determine the suitability for his own use of the products described herein. nor does De Nora Elettrodi Network Companies assume any liability arising out of the use by others of the products referred to herein. Moisture penetration also may occur. staggered strings for system redundancy and maximum current distribution throughout the groundbed. . Please contact us when operation is expected in waters below 5˚ C. resulting in loss of electrical contact. the information herein is not to be construed as absolutely complete since additional information may be necessary or desirable when particular circumstances exist or because of applicable laws or government regulations. Reliability — In choosing the LIDA® tubular anode. recommendations and suggestions appearing herein concerning the use of our products are based upon tests and data believed to be reliable. no guarantee.5 0. suitable cable. years 35 40 45 50 Tubular Anode Life in Mud 35 Anode Current. Please contact us or our approved distributors for advice. String assemblies are also available in a looped configuration with two tails. amps 35 30 25 20 15 ADVANTAGES 10 5 0 0 5 10 15 20 25 30 35 40 45 50 Life. Maximum Current for LIDA® Tubular Anodes (life in years) LIDA® Tubular Anode Life in Brackish Water Anode Current. and understanding.0 Anode Current.lidaproducts. Italy ph: +39 02 2129 2722 fax: +39 02 2129 2801 www. Life. Ease Of Installation — The LIDA® anode-cable assemblies are easy to handle.5 1. years LIDA® Tubular Anode Life in Sand 3. a suitable chlorine resistant cable must be used with the anodes.0 0 5 10 15 20 25 30 35 40 45 50 LIDA® anodes are connected with a special crimping process which improves the life of the tubular anode system. expressed or implied. 10 0 0 5 10 15 LIDA® 20 25 30 Life. The crimp connection is likewise utilized to seal the anode around the cable at both ends. is made by De Nora Elettrodi Network Companies as to the effects of such use or the results to be obtained. It makes your on-site job easier as well.5 x 50 XL 2. assembly and installation factors have been carefully considered so that your time and costs are minimized as much as possible. All information. mechanical crimping process. 20134 Milano. years In chloride rich soils or muds. LIDA® tubular anode strings are backed by a five-year.0 LIDA® Crimp — Many impressed current anodes are connected to the cable with resin-based seals. However. Yet they serve different purposes and are made differently. Electrical connection between the anode and cable is via a patented. Nothing herein contained is to be construed as a recommendation to infringe any patent. Since the actual use by others is beyond our control.0 2. amps De Nora Elettrodi Network recommends the use of quality. registered trademark of ELTECH Systems Corporation. or as multiple. LIDA® is a registered trademark worldwide of Oronzio de Nora SA licensed exclusively to the De Nora Elettrodi Network. amps 30 25 20 15 10 5 0 0 5 10 15 20 25 30 35 40 45 50 Life. This crimping process eliminates the need for mastic or resin sealants. In addition. you have selected the most durable and reliable product in the industry for your cathodic protection needs.5 2. Ventralizer™ is a trademark of ELTECH Systems Corporation. transport and install because of their unique flexibility. years LIDA® Tubular Anode Life in Coke 40 Anode Current. The center crimp makes electrical contact with the cable while the end crimps form a moistureresistant seal. no hassle warranty. a vent pipe and Ventralizers™. amps 60 50 40 30 20 Since only a single cable lead protrudes from the hole.com LIDA® is a U. carbonaceous backfill. • Spherical Tip Prevents hang-up when lowering into deep wells.50% max 0.20 – 14.anotec.25 – 5.Fax 604 / 514-1546 web site: www. BC Canada V3A 4N5 Telephone 604 / 514-1544 .75% 3.com Aug 11. 2004 ISO 9001:2000 REGISTERED Page 1 of 2 .50% max 0. • Caulked Lead • Performance Accelerated Corrosion Tests confirm that Anotec Chill Cast anodes • Pin Type ANOTEC Industries Ltd.00% 0.10% 1.70 – 1.20% max "Chill Cast" in Metal Molds Assures consistent weight.e-mall: info@anotec. Distributed by: 5701 Production Way. greater density. Test reports available on request.com . ANOTEC Chill Cast structure is similar to "Spin Cast" Tubular Anodes. less flake graphite grain boundary. Impact strength and production lot traceablility. Special Features • More than Twice as Strong Independent laboratory tests confirm that Anotec Anodes withstand drop impact tests to more than twice the height of Sand Cast Anodes. Langley. perform significantly better (up to 19%) than Sand Cast anodes in chloride and sulphate environments. Cable Connection Options • Quality Control ISO 9001:2000 Quality Control assures: chemistry (by spectrometer).Produxt Bulletin 90-9 04-07-31 ANOTEC Stick Anodes Solid Chill Cast High Silicon Iron For Impressed Current Cathodic Protection • Product Description Composition (weight %) Grade 3 ASTM A518 Silicon Chromium Carbon Manganese Copper Molybdenum 14. and lower chemical segregation than Sand Cast Anodes. nominal 32W x 22H x 62L inches = 25. Similar to the structure of vacuum refined High Silicon Iron.) 43 (20Kg) 44 (20Kg) 60 (27Kg) 26 (12Kg) 27 (12.19) 3.36) Crate dimensions. Kgs 50 2300 1044 50 2375 1078 45 2850 1293 70 1970 894 60 1770 803 24 2790 1266 (81W x 56H x 158L cm = .0 (.2Ft3 Aug 11. (Sq.5 (38) 3 (76) 60 (1520) 60 (1520) 60 (1520) 60 (1520) 60 (1520) 60 (1520) 2.2 (56) 4 (102) Nominal Weight Lb.0 (.7 (. very fine interdendritic porosity at center.24) 2.71 M3) Page 2 of 2 . Predominantly flake graphite with larger boundary areas than equivalent spheroidal graphite. Ft.6 (.6 (. Anotec Type A typical Cross Section Of a Sand Cast Anode Skin of non-porous equiaxial grains. (Kg) Nominal Area Sq. Occasionally.19) 2.25) 2. Remaining section relatively porous from interdendritic shrinkage and porosity. 2004 ISO 9001:2000 REGISTERED O Shipping Information Anodes per crate Nominal Gross Weight Lbs.Anotec Solid Chill Cast Anodes Grain Structure Makes a Difference A typical ANOTEC Anode Cross Section A dense skin of minute columnar grains and a dense core of equiaxial grains. M.5 (38) 1.7) 110 (50Kg) 2. L A D SHA A EHA EHK EHR A EHM EMK Anotec Type SHA EHA EHM EHK EMK EHR D A D Nominal Dimensions Inches (mm) D L A 2 (51) 2 (51) 2 (51) 1.2 (56) 3 (76) 3 (76) 2.24) 2.2 (56) 2. Predominantly spheroidal shaped graphite.9 (. Loresco RS•3 has a bulk density of 68 lbs per cubic foot. Then. Finally. This breakthrough in surface alteration ensures maximum electronic current transfer with positive anode contact. Earth Contact Backfill INSTALLATION Loresco RS•3. Loresco RS•3 is produced specifically for cathodic protection applications using an exclusive multistep process. The new manufacturing process ensures the impressed current anode and RS•3 system have increased electronic flow performance to further increase the life of the anode system. a very high quality base carbon with desired characteristics is selected. Next. RS•3 is able to handle the demands of stringent field requirements.RS•3 ® LORESCO ® First. takes on the characteristics of super heavy mud. RS•3 combines the characteristics of superior low resistivity and high bulk density with a remarkably rapid sinking ability to provide the latest in conductive carbon backfill technology. pumping from the bottom up is recommended. All particles shaped and surface modified for maximum electrical conductivity and high-current applications. the surfaces of the individual particles are modified to enhance the contact conductance in a process exclusive only to the corrosion industry. With deep anode systems. This manufacturing process is exclusive to conductive carbon formulations designed for cathodic protection. This step results in semi-graphitized carbon particles with excellent conductivity. a specially formulated surfactant is added to reduce particle surface tension for compact settling under water. is simple to install by either mixing and pumping or by pouring dry. due to its maufacturing process. This is the first time a conductive carbon backfill combining pumping ability and pouring ability has been available in one bag. Rapid sinking allows for a faster construction completion time and faster energizing of the anode system. RS•3 is manufactured under a new process which creates a new surface with superior conductive properties. IMPRESSED CURRENT ANODE BACKFILLS Loresco RS•3 is the newest and most innovative super conducting earth contact backfill in the Loresco product line. Because of the new rapid sinking ability RS•3 is able to achieve maximum compaction quickly. to further improve the bulk conductivity. Time before energizing is greatly reduced after installing RS•3. The fixed carbon content is greater than 99% by weight. The bulk density and high fixed carbon content coupled with the assured low resistivity medium allows for longer groundbed life at a lower operating cost. Loresco RS•3 has superb pumping qualities due to the addition of surfactants and when agitated in water. Rapid sinking allows for pouring when pumping is not an option. this carbon is calcined to a minimum temperature of 1250° C under very exacting and controlled standards. The modified surface of the carbon particles coupled with the action 1 . . com ® . These cartridges and the necessary steel discs are then packaged in boxes that are shrink-wrapped. always dry. one for welding copper to copper or copper to steel. copper to cast iron and one for welding copper to steel for cathodic protection. air or ocean freight. The size and weight (in grams) of the cartridge are marked on each individual cartridge. All sizes of weld metal are eligible for thermOweld’s SDS (Same Day Service) shipment.The Ultimate Connection For Quality Products and Service WELD METAL STANDARD CARTRIDGE SIZE #15 #25 #32 #45 #65 #90 #115 #150 #200 #250 #500 10 thermOweld thermOweld® Weld Metal is packaged in moisture-resistant plastic cartridges that have tight fitting caps. thermOweld® Weld Metal is available to be shipped via ground. thermOweld® Weld Metal comes in four types. CATHODIC RAIL PROTECTION PACKED PER CARTRIDGE CARTRIDGE BOX SIZE SIZE #15CI #15CP #15R 20 #25CI #25CP #25R 20 #32CI #32CP #32R 10 #45CI #45CP #45R 20 #65CI #65CP #65R 20 #90CI ~ #90R 10 #115CI ~ #115R 10 ~ ~ #150R 10 ~ ~ #200R 10 ~ ~ #250R 10 ~ ~ #500R 10 thermOweld® Weld Metal is sold in box quantities only CAST IRON CARTRIDGE SIZE +1-918-627-5210 • SALES • SERVICE • TECHNICAL SUPPORT • VISIT www. This insures the weld metal arriving in good condition. and ready for a positive ignition every time.thermOweld. copper to rail. Required Tools. Note that the cable is OFF the surface.5. • • • • • • • • Pipe Dia.thermOweld ® The Ultimate Connection For Quality Products and Service CS-32 TYPE MOLDS CS-32 Horizontal Cable to Horizontal Steel Pipe for Cathodic Protecion CS-32 Type Molds are used to terminate a horizontal copper cable to horizontal steel pipe. Handle Clamps w/ Flint Ignitor (see chart above for correct handles) † ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor Other recommended accessories. 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41) CS-33 CABLE SIZE (mm²) CS-33 TYPE MOLDS Horizontal Cable to Horizontal Cast Iron Pipe for Cathodic Protecion CS-33 Type Molds are used to terminate a horizontal copper cable to horizontal cast iron pipe.5. For expedited service.com 23 . contact thermOweld®. 4 & 6 up to 125 over 125 up to 125 over 125 up to 125 over 125 up to 70 70 to 165 over 165 up to 70 70 to 165 165 to 250 over 250 up to 70 70 to 165 165 to 250 over 250 up to 70 70 to 165 165 to 250 over 250 up to 70 70 to 165 165 to 250 over 250 M-4146‡ M-4147‡ M-4150‡‡ M-4151‡‡ M-4146 M-4147 M-4152 M-4153 M-4154 M-2833 M-2834 M-2835 M-2836 M-4155 M-4156 M-4157 M-4158 M-4159 M-4160 M-4161 M-4162 M-4163 M-4164 M-4165 M-4166 10 16 25 30 35 50 70 PRICE WELD HANDLE KEY METAL CLAMPS 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 15 15 25 25 15 15 25 25 25 32 32 32 32 32 32 32 32 45 45 45 45 65 65 65 65 Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d • • • • • • ‡ 38-4590 Sleeve/Weld Req'd ‡‡ 38-4588 Sleeve/Weld Req'd For sizes not listed. Handle Clamps w/ Flint Ignitor (see chart above for correct handles) † ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor • Other recommended accessories. contact thermOweld®. Size range is 2. contact thermOweld®. contact thermOweld®. in mm MOLD # PRICE WELD HANDLE KEY METAL CLAMPS 2. in mm MOLD # 2.5 mm² through 70 mm² solid or concentric stranded copper conductors. Note that the cable is OFF the surface. 4 & 6 Flat M-4188‡ 3 45CI Not Req’d 10 Surface M-4189‡‡ 3 45CI Not Req’d 16 or M-4188‡‡‡ 3 45CI Not Req’d 25 750 Dia M-4191 3 45CI Not Req’d 35 and M-4192 3 45CI Not Req’d 50 above M-4193 3 45CI Not Req’d 70 pipe M-2868 3 65CI Not Req’d ‡ 38-4590 Sleeve/Weld Req'd ‡‡ 38-4588 Sleeve/Weld Req'd ‡‡‡ 38-4589 Sleeve/Weld Req'd For sizes not listed. For expedited service. contact thermOweld®. 4 & 6 2. Required Tools. 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41) +1-918-627-5210 • SALES • SERVICE • TECHNICAL SUPPORT • VISIT www. For heavy duty molds or molds with wear plates.5 mm² through 70 mm² solid or concentric stranded copper conductors. Size range is 2.5. For heavy duty molds or molds with wear plates. contact thermOweld®. CABLE SIZE (mm²) Pipe Dia.thermOweld. For expedited service.5.The Ultimate Connection For Quality Products and Service thermOweld ® CS-34 TYPE MOLDS CS-34 Horizontal Thru Cable to Horizontal Steel Pipe for Cathodic Protection CS-34 Type Molds are used to join horizontal through copper cable to horizontal steel pipe. 4 & 6 2. Note the cable is ON the surface. contact thermOweld®. For heavy duty molds or molds with wear plates. Handle Clamps w/ Flint Ignitor (see chart above for correct handles) † ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor • Other recommended accessories. contact thermOweld®. 4 & 6 10 16 25 35 50 70 Flat Surface or 750 Dia and above pipe M-2876‡ M-2882‡‡ M-2883‡‡‡ M-2884 M-2887 M-2889 M-2890 PRICE WELD HANDLE KEY METAL CLAMPS 3† 3† 3† 3† 3† 3† 3† 32CI 45CI 45CI 45CI 45CI 65CI 65CI Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d • • • • • • • ‡ (2) 38-4590 Sleeves/Weld Req'd ‡‡ (2) 38-4588 Sleeves/Weld Req'd ‡‡‡ (2) 38-4589 Sleeves/Weld Req'd For sizes not listed. For expedited service.5. 24 CABLE SIZE (mm²) Pipe Dia. Handle Clamps w/ Flint Ignitor (see chart above for correct handles) † ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor • Other recommended accessories.com . Required Tools. contact thermOweld®.5 mm² through 70 mm² solid or concentric stranded copper conductors.thermOweld. CABLE SIZE (mm²) Pipe Dia. Size range is 2. Size range is 2. For heavy duty molds or molds with wear plates. 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41) +1-918-627-5210 • SALES • SERVICE • TECHNICAL SUPPORT • VISIT www. in mm MOLD # 2.5 mm² through 50 mm² solid or concentric stranded copper conductors. contact thermOweld®. in mm MOLD # 2.5. Required Tools. 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41) CS-35 TYPE MOLDS CS-35 Horizontal Thru Cable to Horizontal Cast Iron Pipe for Cathodic Protection CS-35 Type Molds are used to join horizontal through copper cable to horizontal cast iron pipe. contact thermOweld®. contact thermOweld®. 4 & 6 up to 105 over 105 up to 105 over 105 up to 105 over 105 up to 70 70 to 165 over 165 up to 70 70 to 165 165 to 250 over 250 up to 70 70 to 165 165 to 250 over 250 M-4167‡ M-4168‡ M-4169‡‡ M-4170‡‡ M-4171‡‡‡ M-4172‡‡‡ M-4173 M-4174 M-4175 M-4176 M-4177 M-4178 M-4179 M-4180 M-4181 M-4182 M-4183 10 16 25 35 50 PRICE WELD HANDLE KEY METAL CLAMPS 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 3† 25 25 32 32 45 45 32 32 32 45 45 45 45 65 65 65 65 Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d Not Req’d • • • • • • • ‡ (2) 38-4590 Sleeves/Weld Req'd ‡‡ (2) 38-4588 Sleeves/Weld Req'd ‡‡‡ (2) 38-4589 Sleeves/Weld Req'd For sizes not listed. Note the cable is OFF the surface. The enclosures are ideal wherever corrosion resistance.and cadmium-free T Approvals KEMA 03ATEX2078 U T II 2 G EEx e II KEMA 03ATEX2077 T II 2 G EEx e II T6 II 2 (1) G II 1 G EEx e [ia] IIC T6 EEx ia IIC T6 Overview of enclosures Type H x W x D 75 x 80 x 55 75 x 110 x 55 75 x 160 x 55 75 x 190 x 55 75 x 230 x 55 120 x 122 x 90 Standard.and cadmium-free Halogen. RAL 9011 Note: Please specify ambient temperature of application when ordering and also note gasket material (e.58 . similar to RAL 9011 Gasket Cover screws Chloroprene + polyurethane Stainless steel Silicone (VMQ) Stainless steel Protection class Impact resistance IP 66 7J IP 66 7J Temperature range Flammability –40 °C to +90 °C UL94 V0 silicone –55 °C to +100 °C UL94 V0 Toxicity Halogen. RAL 7001 For hazardous areas (Ex). RAL 9011 1277200000 9510210000 1277300000 9510220000 1277400000 9510320000 1565400000 9510330000 9510510000 9510340000 1277500000 9510230000 120 x 220 x 90 1277600000 160 x 160 x 90 1565410000 160 x 260 x 90 1277700000 160 x 360 x 90 1277800000 160 x 560 x 90 9510520000 250 x 255 x 120 1565420000 9510240000 9510250000 9510260000 9510270000 9510350000 9510280000 250 x 400 x 120 1565430000 250 x 600 x 120 9510470000 405 x 400 x 120 1565440000 250 x 255 x 160 9510530000 250 x 400 x 160 9510540000 9510290000 9510300000 9510310000 9510360000 9510370000 Type H x W x D Standard. RAL 7001 For hazardous areas (Ex). RAL 7001 For hazardous areas (Ex). Features: • 17 sizes • Cover with stainless steel screws • Mounting holes located outside of the sealed area • Threaded holes for mounting rails and mounting plates • Approved to the latest international standards Our assembly service can supply these enclosures preassembled with terminals and cable glands according to customer requirements. –55 °C / silicone gasket) A. impact resistance and a high IP protection class are required. Technical data Material Standard ATEX Glass fibre-reinforced polyester to DIN 16913 Glass fibre-reinforced polyester to DIN 16913 with added graphite Surface Grey. RAL 9011 Type H x W x D Standard.Klippon® POK Enclosures Polyester enclosures A The POK series is based on a high-quality glass fibre-reinforced polyester enclosure which represents an economical solution for electrical connections.g. similar to RAL 7001 Black. Lead Wire: 50’ (15m) of # 14 (2.STELTH 2 Direct burial in chloride free conditions Size: 1.5mm2) RHH-RHW wire Material: Ceramic with Moisture Retention Membrane Stability: 5 millivolts with 3.5” (4 cm) Diameter x 7” (18 cm) long.0 microamps load Temperature Range: -10º to 176ºF (-23º to 80º C) Stelth Model SRE-007-CUY Copper-Copper Sulfate (Cu-CuSO4) for buried or concrete service in chloride free environments Stelth Model SRE-008-SUB Silver-Silver Chloride (Ag-AgCI) for buried or concrete service in chloride environments Stelth Model SRE-009-ZUR Zinc-Zinc Chloride (Zn-ZnSO4) for buried or concrete service in chloride free environments “ Engineering Solution Based on Sound Foundation ” . Large.com Info@tinker-rasor. shunts.tinker-rasor. including voltmeters. our people and our customer service.D. clear terminal board can handle a variety of custom configurations. Reducing adapters available for smaller O.5” OD riser pipe. Fits 3. as well. CP TEST STATIONS MODEL T-3 .com An ISO 9001 Registered Company Tinker & Rasor quality is found in our products.com www.’s. teststations. .com Features: 8 Colors 11 terminal positions 5 Rapid Connect binding posts Clear terminal board UV Stabilized color Fire resistant.teststations. and a flange adapter. UV stabilized. See our website for more information www. also available from stock in three colors.detectron. impact resistant Fits 3.5” OD Risers (also available) Distributed by Shunts and other accessories available AVAILABLE FROM STOCK! www. resistors. potentiometers and more.R& A S OR MODEL CP TEST STATION T-3 The Model T-3 is the most versatile Cathodic Protection Test Station available.com www. Fire resistant and Impact resistant poly carbonate material for long outdoor life. 3” x 3.45 kg) Dimensions: 6” x 6” x 4” (152mm x 152mm x 101.6mm x 89.52” (134.1” x 4. and up to eleven (11) binding posts on custom orders.5mm x 111. Also can be custom printing which may meet DOT ID requirements for urban environments. This binding post allows for rapid wire connections on wires as big as 6 AWG. on approval of credit WARRANTY: 90 Days. The terminal board has eleven (11) terminal positions.O.6mm) DELIVERY: Immediately from STOCK F. Each T-3 comes with five (5) zinc plated binding posts.B.teststations. CA USA SERVICE: 24-hour Turn-Around TERMS: Net30 Days. fire protection and impact resistance.75mm) Shipping Weight: 1 lbs (0. The T-3 also features a clear terminal board make of a tough. fire resistance polycarbonate resin. San Gabriel.4” (129. and can be filled with our binding posts. on custom orders.CORROSION MITIGATION INSTRUMENTATION PRODUCT DATA SHEET MODEL T-3 CP TEST STATIONS Features: • 11 hole terminal board • 5 Rapid connection binding posts • Clear terminal board • 8 colors from stock • Fits 3.5” OD riser pipe • UV Stabilized color protection • High impact resistance • Fire resistant • “Easy Grip” top for easy opening with gloves • “Anti-Spin” gasket prevents twisting Construction: Polycarbonate material (Lexan®) gives great UV stabilization. The clear terminal allows you to view both sides of the terminal board without obstruction. most on 1” centers from another. Rapid connection binding posts are zinc plated brass for excellent corrosion resistance.4mm) Cover: 5. Applications: • Cathodic Protection connection point Recommendations: Use with optional items such as the T&R Shock Guard which can be combined with banana jacks for personnel safety. parts and labor Custom configurations and printing available on Model T-3 test stations www.com AVAILABLE FROM STOCK 012-000 . -76˚C to 122˚C (-105˚F to 252˚F) Dimensions: Complete Test Station: Terminal Board:5. stainless screws or banana jacks. Environment: Model T-3 CP Test Stations come standard with the unique Tinker & Rasor binding post with set screw.