Pdn 078927

Serve atOnce Traffica Traffica Z5.2 DX200 Clear Code List DN078927 Issue 1-0 DX200 Clear Code List The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2010/9/9. All rights reserved f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures. Non-observance of these conditions and the safety instructions can result in personal injury or in property damage. Therefore, only trained and qualified personnel may install and maintain the system. The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards. The same text in German: Wichtiger Hinweis zur Produktsicherheit In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Spannung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen. Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverletzungen und Sachschäden führen. Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet. Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen. 2 Id:0900d80580635bef DN078927 Issue 1-0 DX200 Clear Code List Table of Contents This document has 164 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1 2 2.1 2.2 2.3 2.4 2.5 3 4 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Use of clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traffic observation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traffic measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Detailed charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Field reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 13 13 13 13 13 Presentation of clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Effective and ineffective cause codes . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 000H - NORMAL END OF CALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 001H - SUSPENDED CALL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 003H - CALL DURATION BELOW SUPERVISION TIME . . . . . . . . . . . 23 004H - B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 005H - CALLED SUBSCRIBER BUSY . . . . . . . . . . . . . . . . . . . . . . . . . 24 006H - TIME-OUT FOR B-SUBSCRIBER ANSWER . . . . . . . . . . . . . . 24 007H - CALL WAITING TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 008H - CALLED SUBSCRIBER NOT CONNECTED . . . . . . . . . . . . . . 26 009H - CALL ALREADY WAITING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 00AH - INTERVENTION ALREADY ON . . . . . . . . . . . . . . . . . . . . . . . . 27 00BH - REROUTING DUE TO B-SUBSCRIBER FACILITY . . . . . . . . . 27 00CH - OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE 28 00EH - MALICIOUS CALL TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . 28 00FH - INTERMEDIATE CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . 29 010H - ABSENT SUBSCRIBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 011H - OPERATOR PRIORITY ACCESS . . . . . . . . . . . . . . . . . . . . . . . 30 012H - NO PAGING RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 013H - CALL TRANSFER RECALL DUE TO C-SUBSCRIBER ANSWER TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 015H - NORMAL UNSPECIFIED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 016H - SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 018H - INTERMEDIATE CHARGING IN THE END OF THE PHASE CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 020H - ANNOUNCEMENT SUCCESS IN INTERCEPTION . . . . . . . . . 33 025H - CALL DROP BACK RELEASE . . . . . . . . . . . . . . . . . . . . . . . . . 34 031H - NOT ENOUGH CREDIT TO CALL . . . . . . . . . . . . . . . . . . . . . . 35 100H - CIRCUIT RE-SEIZED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 101H - CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE 36 DN078927 Issue 1-0 Id:0900d80580635bef 3 . . . . . . . . . . . . . . . .ACCESS TO B-SUBSCRIBER LINE RESTRICTED . . . . . . . . . . . . . . . . . . . .CLEAR IN DETAILED CHARGING . . . . .37 5. . . . . . 47 252H . 51 308H . . . . . 47 220H . . . . . . . . . . 41 20FH . . . 54 30CH . . . .CHANGE OF OUTGOING CIRCUIT . . . . . . . .44 5. . . 50 306H . 54 30DH . . . . . . . . . . . . . . .62 5.ANONYMOUS CALLS REJECTION . . . . . . . . .64 5. . . . . . 40 207H . . . . . . . . .DX200 Clear Code List 5. . . . .NETWORK. . . . .CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION . . . . . 43 213H . . . 46 219H . . . . . . . . . . . . . .B-NUMBER UNUSED. .38 5. . . . . . . . . . . . . . . . . . . . .41 5. . . . . . . 58 315H . . . 58 317H . . . . 42 210H . . . .CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE . . . . . . . . . . . . . . . . . . . . . .57 5. . . . . . . . . . . . . . .29 5. . . . . . . . . . . .OR C-NUMBER IS NOT REGISTERED . . . . . .CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE . . . . . .TELESERVICE NOT PROVIDED . . . . . . . .CHARGING IN WRONG PHASE OF CALL . .46 5.B. . . . . . . . . . . .ESTABLISHED B-CHANNEL .B-CHANNEL UNACCEPTABLE . 37 201H . . . . . . . . . . .CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER . . . . . .BEARER SERVICE NOT PROVIDED . . . . . . . . . . . . . . 40 20BH . . . . . .54 5. . . . . . . 59 31AH . . . . . . . . . . . . . . . . . 56 310H . . . . . . . . . . . . . 53 30BH . . . .CALLED SUBSCRIBER LINE FAULTY . .59 5.NULL NUP . . .50 5. 39 206H . . . . . . . . . . . . . . . . . 60 4 Id:0900d80580635bef DN078927 Issue 1-0 . . . . . . . . . . . . . . . . . . .51 5. . . . . . . . . . . . . . . . . . .SUBSCRIBER CONGESTION . . . . . . . . . . . . . . 41 20EH . . . .CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR . . . . .65 5. . . .33 5. . . . . . .53 5. .47 5. . . . . . . . . . . . .67 102H . . . . . . .OUT OF CATCHMENT AREA . . . . . . . . . . . . . . . . . .32 5. . . . . 56 30FH . . . . . . . . . . .CALLED SUBSCRIBER LINE OUT OF SERVICE . .B-NUMBER CHANGED . . . . . . . .35 5. . . . . . . . .28 5. . . . .CALL DROP BACK . .CALLED SUBSCRIBER HAS CALL DIVERSION BARRING . . . . . . 57 312H . . . . . . . . . . . . .49 5. . . . . . . . . . . . . . . . . . . . .60 5. . . . . .31 5. . . 57 311H . . . 45 218H . . . . . 36 103H . REJECTED DIVERTED CALLS . . . USER NOT IN CUG . . . . . . . . . . . . . . . . . . . . . . . . . . .58 5. . . . . .55 5. . . . . . 52 309H . . . .66 5.56 5. . . . . . . . . 48 301H . . 39 204H . . . . . . . . . . . . . . . .43 5. . . 37 202H . . . . . . . . . . .34 5. . . . . . . . . . .45 5. . . . . . . . . 51 307H . . . . . . . . . . . .39 5. . . 50 305H . . . . . .40 5. . . .42 5. . .CALL RELEASED . . . . . .48 5. . . .CALLED SUBSCRIBER LINE BLOCKED . . . . . . . . . . . . . . . . . . . . . .CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT. . 44 215H . . . . .CALL REJECTED . . . .UNTERMINATED CALL TO A PORTED NUMBER . . . . .TEMPORARY OUT OF ORDER . . 45 217H . . . . . . . . . . . . . . . . . . . .61 5. . . . . . . . . . . 42 211H . . . . .27 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CALL RECORD RELEASED DURING CALIBRATION . . . . . . . . .30 5. . . .NETWORK. . . . . . . . . . . . . . . .CHANGE IN NUMBERING PLAN.MISDIALLED TRUNK PREFIX . . . . . . .INCOMING CALLS BARRED WITHIN THE CUG . . . . . . . . . . . . . . . .TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION 53 30AH . . . . . . . 49 304H . . . . . . . 44 216H . . . . . . . . . . . . 55 30EH . . . . . . . . . . . . . . . . . . . . . .36 5.63 5. . . . . . . . . . . . .TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE . .52 5. . . . . . .TRANSLATION OUT-OF-SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 300H . . . .REANSWER TIME OUT. 38 203H . . . . .CLOSED USER GROUP RESCTRICTION . . . . . . 64 403H . . . . . . . . . . . .REGISTER ANALYSIS FAILED. . . 62 322H . . . .80 5. . . . . . . . . .HOP COUNTER EXHAUST . . . . .87 5. . . .97 5. . . . . . . . . . . .UNKNOWN CUG INDEX . . . . . . . . . . . . . 83 702H . . . . . . . .FILE RECORD CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 601H .POLARITY REVERSAL FAILURE .CALL CLEARED BY MML . . . . . . . . . . . . . .74 5. . . . . . . . . . . . . . . . .102 5. . . . . . . . . . . . . . . . . . . . .82 5.OUTGOING CALLS BARRED WITHIN THE CUG . . .79 5. . . . . . . . . . 84 704H . . . . . .NO CUG SELECTED. . . . . . . 73 50DH . . . . . . . . . . . . . .QUEUEING TIME EXCEEDED . . .ATTENUATOR CONGESTION . . . . . . . . . . . .FACILITY CONTROL FAILED. . . .76 5. . . . . . . .CHARGING ERROR . 61 321H . . . .84 5. .SUBSCRIBER MODULE RESTARTED. .83 5. . . . . . . . 76 603H . . 76 604H .UNIT RESTARTED . .92 5. . . . . . . . .CONFERENCE DEVICE CONGESTION . . . . . . . . . . . . . . . .104 5.REGISTER TOTAL TIME EXCEEDED . . . . . . . . .68 5. . . . . . . . . . . . . . .DX200 Clear Code List 5. . . .LINES OF LINE HUNTING GROUPS BARRED . . . . . . . . . . . . . . . 77 606H . 78 607H . . . .86 5. . . . . . . 87 70BH . . . . . . . . . . . . .112 31CH . . .LONG AON REQUEST . . . . . . . 87 DN078927 Issue 1-0 Id:0900d80580635bef 5 . . . . . 81 60FH . . . . . . . . . .ERRONEOUS SERVICE REQUEST FROM CO-PROCESS . . . . . . . . . . 69 40BH . . . . . 80 60DH . . . . . . .FILE ERROR . . . . . .SUBSCRIBER NOT A MEMBER OF THE CUG . . . . . . . . . . .INTERNAL CALL LINK CONGESTION . . . .70 5. . . . . 81 60EH . . . . . . 82 701H . . . . 65 404H . . . 86 707H . . . . . . . . . . . . . . . . . . . . . . . . . . .CALL INTERRUPTED DURING REGISTER ANALYSIS . . . . . . .PBRU DEVICE CONGESTION . . . . . .CHARGING NOT STARTED . . . . . .FORCED CLEAR OF A CALL . . . . . . . . .INTERWORKING UNIT CONGESTION . . . . . . . . . . . . .STAGE CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 70AH . . . .69 5. .99 5. . . . . . . . . . . . . . . . .PARITY ERROR FROM PBRU/MFCU DEVICE . . . . . . . . . .73 5. 68 409H . . . . . . . .77 5. . . . . . . . . . . . . . . . . .CONNECTION FAILED IN SSW/SWI . . . . . . . .72 5. . . . . . 79 609H . .REGISTER CONGESTION . . .98 5. . . . . . . . 60 31DH . . . . . . . . . . . . . . 63 402H . . . . . . . . . . . 63 401H .MFC-ASS-CHANNEL CLOSING MISSED . . . . . . . . . . .105 5. .SUBSCRIBER MODULE OR V5 INTERFACE FAILURE. . . . . .108 5. .71 5.101 5. . . . . . . . . . . . 72 50CH . . . . . . . . . . . . . . . . . . . . . .89 5. . . . . . . . . . . . . .94 5. CALL CLEARED . . . . . . 66 406H . . . . . . . . . .ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK. . . . . . . . . 84 705H . . . . . . . . . 78 608H . . . . . . . . . 74 600H . . 67 408H . .78 5. . .LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED . . . . . . . . .MODEM ERROR . . .103 5. . . . . . . 70 506H . . . . . . . . . 66 407H .106 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 60BH . . . . . . . . . . . . .CONNECTION FAILED IN GSW/SWI . . . . .111 5. . . 85 706H . . . . . . .96 5. .UNSUITABLE MODULE CIRCUIT . . . .95 5.100 5. . . . . . .110 5. . 71 508H . . .MODULE OR V5 CONGESTION. . . . . . . 75 602H . . . . . . . . . .OVERLOAD CONGESTION . . 81 700H . . . . .81 5. . . . . .NO RESPONSE FROM PARTNER PROGRAM BLOCK . . . . . . . . . 73 50FH . . . . . . . . . . . 62 400H . . . . .109 5. . . . . .75 5. . . . . . . . . . . . . . . . 72 50BH . . . . . . . . . . . . . . . . . . . . . . . .91 5. . . . . . . .107 5.85 5. . . . 65 405H . . . .MFCU DEVICE CONGESTION .88 5. . . .MODULE OR V5 INTERFACE NOT AVAILABLE . . . . . .90 5. . . . . . . . . . . 69 40AH . .CIRCUIT CONGESTION DUE TO TRAFFIC TYPE . . . . . . . . .93 5. . . . . . . . . . . . . . . . . . . . . . . 71 509H . .MODULE ROUTE OR SSW CONGESTION . . . . . . . . . . . DX200 Clear Code List 5.113 5.114 5.115 5.116 5.117 5.118 5.119 5.120 5.121 5.122 5.123 5.124 5.125 5.126 5.127 5.128 5.129 5.130 5.131 5.132 5.133 5.134 5.135 5.136 5.137 5.138 5.139 5.140 5.141 5.142 5.143 5.144 5.145 5.146 5.147 5.148 5.149 5.150 5.151 5.152 5.153 5.154 5.155 70CH - OVERLOAD CONTROL SYSTEM ERROR . . . . . . . . . . . . . . . . 88 70DH - ANNOUNCEMENT SERVICE FAILURE . . . . . . . . . . . . . . . . . . 88 70EH - CONFIGURATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 710H - NO ANALYSIS FOR CARRIER ACCESS CODE . . . . . . . . . . . . 89 711H - TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE . . . . . . . . 90 712H - TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 713H - NO ISUP ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 714H - ATTRIBUTE DIRECTED ROUTING MISMATCH . . . . . . . . . . . . 91 715H - REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 716H - REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 718H - DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 719H - NO RESOURCE AVAILABLE FOR CALL . . . . . . . . . . . . . . . . . 94 71AH - IDENTIFIED CHANNEL NOT EXIST . . . . . . . . . . . . . . . . . . . . . 95 71BH - REQUESTED CHANNEL NOT AVAILABLE . . . . . . . . . . . . . . . 95 71CH - PACKET CONTROL UNIT CONGESTION . . . . . . . . . . . . . . . . 96 71DH - POINT-TO-POINT PROTOCOL ERROR . . . . . . . . . . . . . . . . . . 96 801H - LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 802H - LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED . 97 803H - INVALID CALLING SUBSCRIBER CATEGORY . . . . . . . . . . . . 98 804H - OUTGOING CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . 99 806H - IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE . . 99 809H - ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT . . 100 80AH - ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT . . . 101 80BH - NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT. . . . . . 101 80CH - UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT. 102 80DH - OUTGOING CIRCUIT OUT OF ORDER . . . . . . . . . . . . . . . . . 102 80EH - INCOMING CIRCUIT OUT OF ORDER . . . . . . . . . . . . . . . . . . 103 80FH - CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 810H - FACILITY NOT SUPPORTED . . . . . . . . . . . . . . . . . . . . . . . . . 104 811H - NETWORK FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 813H - SWITCHING EQUIPMENT CONGESTION . . . . . . . . . . . . . . . 105 814H - CIRCUIT GROUP CONGESTION . . . . . . . . . . . . . . . . . . . . . . 105 815H - ACCESS BARRED TO THE CALLED SUBSCRIBER . . . . . . . 106 816H - CALL FAILED, SEND SPECIAL INFORMATION TONE . . . . . 106 817H - NETWORK, UNALLOCATED NUMBER. . . . . . . . . . . . . . . . . . 107 818H - NETWORK, LINE OUT OF SERVICE . . . . . . . . . . . . . . . . . . . 107 819H - NETWORK, SUBSCRIBER NUMBER CHANGED . . . . . . . . . . 108 81AH - CONGESTION IN TERMINAL EXCHANGE. . . . . . . . . . . . . . . 109 81DH - CONGESTION IN INTERNATIONAL CALL . . . . . . . . . . . . . . . 109 81EH - CONTROLLED NOT READY . . . . . . . . . . . . . . . . . . . . . . . . . . 110 81FH - NETWORK, OVERLOAD CONGESTION . . . . . . . . . . . . . . . . 110 820H - NETWORK MESSAGE CONTENT ERROR. . . . . . . . . . . . . . . 111 821H - INVALID TRANSIT NETWORK SELECTION . . . . . . . . . . . . . . 111 6 Id:0900d80580635bef DN078927 Issue 1-0 DX200 Clear Code List 5.156 5.157 5.158 5.159 5.160 5.161 5.162 5.163 5.164 5.165 5.166 5.167 5.168 5.169 5.170 5.171 5.172 5.173 5.174 5.175 5.176 5.177 5.178 5.179 5.180 5.181 5.182 5.183 5.184 5.185 5.186 5.187 5.188 5.189 5.190 5.191 5.192 5.193 822H - RECOVERY ON TIMER EXPIRY . . . . . . . . . . . . . . . . . . . . . . 112 824H - PCM FAULTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 828H - CONGESTION FROM NATIONAL NETWORK . . . . . . . . . . . . 113 829H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 830H - NUMBER PORTABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 832H - ROUTING ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 833H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE 116 851H - TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNALLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 900H - NO MF FORWARD SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . 117 901H - TOO LONG MF FORWARD SIGNAL . . . . . . . . . . . . . . . . . . . 117 905H - TOO LONG MF BACKWARD SIGNAL . . . . . . . . . . . . . . . . . . 118 90CH - PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 90EH - PREMATURE ANSWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 90FH - ANSWER AFTER B BUSY . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 A01H - CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 A02H - INVALID MESSAGE FROM TRUNK CIRCUIT . . . . . . . . . . . . 121 A03H - INTERWORKING FAILED. . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 A04H - TRUNK CIRCUIT PROTOCOL ERROR . . . . . . . . . . . . . . . . . 122 A05H - CIRCUIT RELEASED BY CO-EXCHANGE . . . . . . . . . . . . . . 122 A07H - CALL FAILURE FROM OUTGOING CIRCUIT . . . . . . . . . . . . 123 A08H - INTER-EXCHANGE SIGNALLING OUT OF ORDER . . . . . . . 123 A09H - ADDRESS COMPLETE MESSAGE TIME-OUT . . . . . . . . . . . 124 A0AH - ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED 125 A0CH - NO DIGITAL TRUNK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 A0DH - NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION . . 126 A0EH - NO CIRCUIT AVAILABLE IN TRANSIT NETWORK. . . . . . . . 126 A0FH - RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 B02H - TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 B0FH - LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 B11H - MODEM COMMUNICATION ERROR. . . . . . . . . . . . . . . . . . . 129 B17H - ADDRESS INCOMPLETE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 B18H - SERVICE UNAVAILABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 B19H - SERVICE INCOMPATIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 B20H - NETWORK ADDRESS EXTENSION (NAE) ERROR . . . . . . . 131 B21H - DTE IS UNCONTROLLED . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 B23H - DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT. . . . . . . . 132 B2AH - BLOCKING RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 B2BH - PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED . 133 DN078927 Issue 1-0 Id:0900d80580635bef 7 DX200 Clear Code List 5.194 5.195 5.196 5.197 5.198 5.199 5.200 5.201 5.202 5.203 5.204 5.205 5.206 5.207 5.208 5.209 5.210 5.211 5.212 5.213 5.214 5.215 5.216 5.217 5.218 5.219 5.220 5.221 5.222 5.223 5.224 5.225 5.226 5.227 5.228 5.229 5.230 B2CH - INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR. 133 B2DH - INTELLIGENT NETWORK APPLICATION RESPONSE TIMEOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 B2EH - MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 B2FH - TCAP ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 B30H - ASN1 CODING OR DECODING ERROR . . . . . . . . . . . . . . . . 136 B31H - SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 B32H - CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 B33H - CONTINUITY CHECK FAILURE . . . . . . . . . . . . . . . . . . . . . . . 137 B34H - A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 B35H - TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD 138 B36H - CALLING CARD NUMBER SELECTED BY USER NOT FOUND . 139 B37H - IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD . . . 140 B38H - IN FALLBACK CODE ONE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 B39H - IN FALLBACK CODE TWO . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 B3AH - IN FALLBACK CODE THREE . . . . . . . . . . . . . . . . . . . . . . . . . 141 B3BH - IN FALLBACK CODE FIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 B3CH - IN FALLBACK CODE FOUR . . . . . . . . . . . . . . . . . . . . . . . . . . 143 B3DH - IN DIALOG - ROUTING FAILURE IN SS7 NETWORK . . . . . . 143 C00H - DIAL WAIT TIME EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . 144 C01H - PROHIBITED DIALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 C02H - INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING . . 145 C04H - CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD. . . 146 C05H - CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY . . . . 146 C06H - CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER . 147 C08H - PREMATURE DIALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 C09H - SERVICE OR FACILITY ACTIVATION RESTRICTED . . . . . . 148 C0AH - SERVICE OR FACILITY USAGE RESTRICTED. . . . . . . . . . . 149 C0BH - INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS . . . 149 C0DH - BEARER CAPABILITY NOT PRESENTLY AVAILABLE . . . . . 150 D00H - SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR 150 D01H - SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR. . 151 D03H - SERVICE OR FUNCTION NOT IMPLEMENTED . . . . . . . . . . 151 D04H - SUBSCRIBER SIGNALLING PROTOCOL ERROR . . . . . . . . 152 D06H - AOCC CHARGING ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 D07H - NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 D08H - GSM ERH 4.08 PROTOCOL TIMER EXPIRES. . . . . . . . . . . . 154 D0BH - DUAL LOG-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 8 Id:0900d80580635bef DN078927 Issue 1-0 . . . . . . 155 D10H . . . . . . . . . . . . . . . . . . . . . . . . . 157 Glossary. . . . . . . . . .MANDATORY INFORMATION ELEMENT MISSING . . . . . . . . . . . . . . . . . . . . . . 164 DN078927 Issue 1-0 Id:0900d80580635bef 9 . . 156 Clear code index . . . .233 6 D0FH . . . . . .INVALID INFORMATION ELEMENT CONTENT . . . . .231 5. . . . . . . . .232 5.ISDN-SUBSCRIBER FACILITY DIALLING REJECTED . . .DX200 Clear Code List 5. . . . . . . . . . 155 D11H . . . . . . . . . . . . . . . 0030H. 0252H. 0A0FH and 0B11H Chapter Clear codes Modified clear codes: 0719H. 050EH. Changes made between issues 10 and 9 Chapters Effective and ineffective clear codes. 040BH. Clear codes and Clear code index Added clear codes: 0025H. the default effect of the clear code has been changed. Clear codes and Clear code index Added clear codes: 0012H. 0218H. 0710H.Summary of changes DX200 Clear Code List Summary of changes Changes between document issues are cumulative. 071DH. 0217H. 0216H. the latest document issue contains all changes made to previous issues. 0832H. 0219H. 070BH. 0833H. Changes made between issues 9 and 8 Chapters Effective and ineffective clear codes. Changes made between issues 11 and 10 Chapters Effective and ineffective clear codes. 0A0EH. 0031H. 081EH and 0830H 10 Id:0900d80580635beb DN078927 Issue 1-0 . 071CH. Clear codes and Clear code index Added codes 0821H and 0C0DH. 0220H. Therefore. 07FFH: internal congestion 0800H . but which nevertheless lead to clearing of a call or to an interruption in call set-up. 'subscriber errors' (0C00H .07FFH) consists of cases in which a call or call set-up is interrupted because of an error in the originating exchange. The clear codes are transferred from the call control to the statistical system in the following messages: • • • • charging facility charging (facility control) call set-up interrupted call interrupted The clear codes affect both the tasks and outputs of the following system blocks and program blocks: • Call Control (CLCSYB) DN078927 Issue 1-0 Id:0900d80580635beb 11 . 'external congestion' (0800H -0BFFH) includes all the cases in which a call or call set-up is interrupted because of an error outside the originating exchange. 'internal congestion' (0400H .03FFH: normal clearing 0400H . for example.01FFH: normal clearing / internal congestion: clear codes set by charging and statistics and not leading to a release 0200H . The class has been further divided into four subclasses • • • 0000H . the class contains clear codes associated with communication between the various units and program blocks of the exchange and those associated with handling of files. This manual also describes the use of the clear codes in the DX 200 system.DX200 Clear Code List Introduction 1 Introduction The DX 200 Clear Code List contains descriptions of all clear codes sent from the call control program blocks to the statistical process. caused by a congestion outside the network element. This group consists mainly of clear codes related to inter-exchange signalling. The third main class.03FFH: normal clearing / subscriber error: normal congestion caused by the subscriber's facility or equipment. for example.02FFH: normal clearing / external congestion: normal clearing situations. subscriber busy 0100H .0FFFH) includes the cases in which a call or call set-up is interrupted by a calling subscriber's error or by a failure in the subscriber's equipment or by faulty subscriber signalling.00FFH: normal clearing / normal clearing: normal clearing situations. Clear codes have been given hexadecimal numbers from 0000H to 0FFFH. The second main class. Primarily.0FFFH: subscriber errors The main class 'normal clearing' consists of clear codes which have not been caused by error in the network element or by subscriber error. • . Clear codes have been divided into four main classes: • • • • 0000H .0BFFH: external congestion 0C00H . The fourth main class. by a congestion on the radio path 0300H . Introduction DX200 Clear Code List • • • • • • • • Signalling Services (SGLSYB Statistical Program Block (STPROC) Charging Program Block (CGPROC) Charging Control Program Block (CGLSTA) Text Forming Program Block (TEXTPR) Traffic Measurement Program Block (TRAMNT) Traffic Measurement MML (TRMSNT) Traffic Observation MML (TROBSN) 12 Id:0900d80580635beb DN078927 Issue 1-0 . 0FFFH). it is important to distinguish between 'normal clearing' and 'clearing due to error'.07FFH.DX200 Clear Code List Use of clear codes 2 Use of clear codes The individual clear codes or clear code groups are utilized in the following functions of the DX 200 system: • • • • • • traffic observation traffic measurement traffic maintenance supervision detailed charging field reporting load observation A more detailed description of these functions follows. 0400H . 2. The Service Level File can be defined to include eight code groups. for example. 2.2 Traffic measurement Traffic measurement uses the main classes of clear codes. DN078927 Issue 1-0 Id:0900d80580635beb 13 . that is. The number of occurrences of the clear codes belonging to these groups are updated. which may comprise any clear codes (0000H . the observation can be limited to a certain clear code. Here. In other observation categories. 2. in destination observation and in the observation of failed calls. The occurrences of each clear code are also registered in the Service Level File.3 Maintenance supervision Supervision of the error ratio of circuit groups and control units is part of the maintenance supervision. In two observation categories. irrespective of the cause of error. This means that traffic observation reports are given only on calls that fall into the defined category. clear codes have no function. or to a certain clear code range.4 Detailed charging Individual clear codes received in the charging messages and facility charging messages are significant for detailed charging. to the Service Level File. 0804H. 2. group by group. for example.1 Traffic observation Traffic observation uses individual clear codes.5 Field reporting Individual clear codes and the classification of clear codes in the Service Level File of the statistics system are used in field reporting. 2. The name of the program block that detects the clear code. A description of the clear code. 14 Id:0900d80580635beb DN078927 Issue 1-0 . Number Name Description Detected by The hexadecimal number of the clear code (0000H -0FFFH). The description is given in the following form. The name of the clear code in the MML programs. The name of the clear code. Alarms A list of possible alarms which are set when the clear code occurs in the exchange.Presentation of clear codes DX200 Clear Code List 3 Presentation of clear codes Clear codes have been described in numerical order. Description of the situation which causes the clear code to be set. A description of the effects that the clear code has on Text in MML printouts Default effect on the exchange the exchange Possibility to change the default effect This field states whether it is possible to change the default effect. However. Ineffective clear codes indicate that the call did not reach conversation state. effective clear codes are those codes that can be generated when a call reaches conversation state. List of effective and ineffective clear codes: NUMBER 0000H 0001H 0003H 0004H 0005H 0006H 0007H 0008H 0009H 000AH 000BH 000CH 000EH 000FH 0010H 0011H 0012H 0013H 0015H 0016H 0020H 0025H 0030H 0031H 0100H 0101H 0102H 0103H 0201H 0202H 0203H NAME OF CLEAR CODE NORMAL END OF CALL SUSPENDED CALL CALL DURATION BELOW SUPERVISION TIME B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT CALLED SUBSCRIBER BUSY TIME-OUT FOR B-SUBSCRIBER ANSWER CALL WAITING TIME-OUT CALLED SUBSCRIBER NOT CONNECTED CALL ALREADY WAITING INTERVENTION ALREADY ON REROUTING DUE TO B-SUBSCRIBER FACILITY OUTGOING DIRECTION RESTRICTED DUE TO MALICIOUS CALL TRACING INTERMEDIATE CHARGING ABSENT SUBSCRIBER OPERATOR PRIORITY ACCESS NO PAGING RESPONSE CALL TRANSFER RECALL DUE TO C-SUBSCRIBER NORMAL UNSPECIFIED SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE ANNOUNCEMENT SUCCESS IN INTERCEPTION CALL DROP BACK RELEASE USER CREDIT LIMIT REACHED NOT ENOUGH CREDIT TO CALL CIRCUIT RE-SEIZED CIRCUIT RELEASED BEFORE 'END OF THE CALL' CALL RECORD RELEASED DURING CALIBRATION CHARGING IN WRONG PHASE OF CALL CALL RELEASED CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT B-CHANNEL UNACCEPTABLE DN078927 Issue 1-0 Id:0900d80580635beb 15 . ineffective clear codes are important statistically.DX200 Clear Code List Effective and ineffective cause codes 4 Effective and ineffective cause codes The operator can use clear codes when generating charging. In the list below. USER NOT IN CUG CALL DROP BACK MISDIALLED TRUNK PREFIX TEMPORARY OUT OF ORDER OUT OF CATCHMENT AREA TRANSLATION OUT-OF-SERVICE ANONYMOUS CALLS REJECTION UNTERMINATED CALL TO A PORTED NUMBER CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR CALLED SUBSCRIBER LINE OUT OF SERVICE CALLED SUBSCRIBER LINE FAULTY ACCESS TO B-SUBSCRIBER LINE RESTRICTED B-NUMBER UNUSED B-NUMBER CHANGED TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER REANSWER TIME OUT B.OR C-NUMBER IS NOT REGISTERED CALLED SUBSCRIBER LINE BLOCKED CHANGE IN NUMBERING PLAN CLOSED USER GROUP RESCTRICTION BEARER SERVICE NOT PROVIDED TELESERVICE NOT PROVIDED CALLED SUBSCRIBER HAS CALL DIVERSION BARRING TIME-OUT IN INTELLIGENT NETWORK BASED INCOMING CALLS BARRED WITHIN THE CUG 16 Id:0900d80580635beb DN078927 Issue 1-0 . REJECTED DIVERTED CALLS NETWORK.Effective and ineffective cause codes DX200 Clear Code List 0204H 0206H 0207H 020BH 020EH 020FH 0210H 0211H 0213H 0215H 0216H 0217H 0218H 0219H 0220H 0252H 0300H 0301H 0304H 0305H 0306H 0307H 0308H 0309H 030AH 030BH 030CH 030DH 030EH 030FH 0310H 0311H 0312H 0315H 0317H 031AH ESTABLISHED B-CHANNEL CALL REJECTED SUBSCRIBER CONGESTION CLEAR IN DETAILED CHARGING CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE CHANGE OF OUTGOING CIRCUIT NULL NUP NETWORK. DX200 Clear Code List Effective and ineffective cause codes 031CH 031DH 0321H 0322H 0400H 0401H 0402H 0403H 0404H 0405H 0406H 0407H 0408H 0409H 040AH 040BH 0506H 0508H 0509H 050BH 050CH 050DH 050EH 050FH 0600H 0601H 0602H 0603H 0604H 0606H 0607H 0608H 0609H 060BH 060DH 060EH 060FH 0700H SUBSCRIBER NOT A MEMBER OF THE CUG OUTGOING CALLS BARRED WITHIN THE CUG NO CUG SELECTED UNKNOWN CUG INDEX ATTENUATOR CONGESTION INTERWORKING UNIT CONGESTION REGISTER TOTAL TIME EXCEEDED MFCU DEVICE CONGESTION PBRU DEVICE CONGESTION ERRONEOUS SERVICE REQUEST FROM C0-PROCESS CONNECTION FAILED IN GSW/SWI ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED CONNECTION FAILED IN SSW/SWI CIRCUIT CONGESTION DUE TO TRAFFIC TYPE HOP COUNTER EXHAUST LINES OF LINE HUNTING GROUPS BARRED CHARGING ERROR FILE ERROR MODULE ROUTE OR SSW CONGESTION MFC-ASS-CHANNEL CLOSING MISSED FACILITY CONTROL FAILED UPDATE LOG BLOCKING UNSUITABLE MODULE CIRCUIT FILE RECORD CONGESTION MODULE OR V5 CONGESTION REGISTER CONGESTION NO RESPONSE FROM PARTNER PROGRAM BLOCK INTERNAL CALL LINK CONGESTION CONFERENCE DEVICE CONGESTION POLARITY REVERSAL FAILURE CHARGING NOT STARTED CALL CLEARED BY MML OVERLOAD CONGESTION STAGE CIRCUIT CONGESTION UNIT RESTARTED SUBSCRIBER MODULE OR V5 INTERFACE FAILURE. CALL CLEARED LONG AON REQUEST DN078927 Issue 1-0 Id:0900d80580635beb 17 . Effective and ineffective cause codes DX200 Clear Code List 0701H 0702H 0704H 0705H 0706H 0707H 070AH 070BH 070CH 070DH 070EH 0710H 0711H 0712H 0713H 0714H 0715H 0716H 0718H 0719H 071AH 071BH 071CH 071DH 0801H 0802H 0803H 0804H 0806H 0807H 0808H 0809H 080AH 080BH 080CH 080DH REGISTER ANALYSIS FAILED QUEUEING TIME EXCEEDED PARITY ERROR FROM PBRU/MFCU DEVICE MODULE OR V5 INTERFACE NOT AVAILABLE CALL INTERRUPTED DURING REGISTER ANALYSIS SUBSCRIBER MODULE RESTARTED FORCED CLEAR OF A CALL MODEM ERROR OVERLOAD CONTROL SYSTEM ERROR ANNOUNCEMENT SERVICE FAILURE CONFIGURATION ERROR NO ANALYSIS FOR CARRIER ACCESS CODE TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE NO ISUP ROUTE ATTRIBUTE DIRECTED ROUTING MISMATCH REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION NO RESOURCE AVAILABLE FOR CALL IDENTIFIED CHANNEL NOT EXIST REQUESTED CHANNEL NOT AVAILABLE PACKET CONTROL UNIT CONGESTION POINT-TO-POINT PROTOCOL ERROR LENGTH OF ORIGINAL CALLED SUBSCRIBER EXCEEDED LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED INVALID CALLING SUBSCRIBER CATEGORY OUTGOING CIRCUIT CONGESTION IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE WAITING TIME FOR MFC PAUSE SIGNAL EXCEEDED WAITING TIME FOR MFC BACKWARD SIGNAL EXCEEDED ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT UNKNOWN DECADIC SIGNAL FROM INCOMING OUTGOING CIRCUIT OUT OF ORDER 18 Id:0900d80580635beb DN078927 Issue 1-0 . DX200 Clear Code List Effective and ineffective cause codes 080EH 080FH 0810H 0811H 0813H 0814H 0815H 0816H 0817H 0818H 0819H 081AH 081DH 081EH 081FH 0820H 0821H 0822H 0824H 0828H 0829H 0830H 0832H 0833H 0851H 0900H 0901H 0905H 090CH 090DH 090EH 090FH 0A01H 0A02H 0A03H 0A04H 0A05H INCOMING CIRCUIT OUT OF ORDER CIRCUIT CONGESTION FACILITY NOT SUPPORTED NETWORK FAILURE SWITCHING EQUIPMENT CONGESTION CIRCUIT GROUP CONGESTION ACCESS BARRED TO THE CALLED SUBSCRIBER CALL FAILED. SEND SPECIAL INFORMATION TONE NETWORK. OVERLOAD CONGESTION NETWORK MESSAGE CONTENT ERROR INVALID TRANSIT NETWORK SELECTION RECOVERY ON TIMER EXPIRY PCM FAULTY CONGESTION FROM NATIONAL NETWORK DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION NUMBER PORTABILITY ROUTING ERROR DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE TRAFFIC TO CONGESTED DESTINATION POINT NO MF FORWARD SIGNAL TOO LONG MF FORWARD SIGNAL TOO LONG MF BACKWARD SIGNAL PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT WAITING TIME FOR ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT EXCEEDED PREMATURE ANSWER ANSWER AFTER B BUSY CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) INVALID MESSAGE FROM TRUNK CIRCUIT INTERWORKING FAILED TRUNK CIRCUIT PROTOCOL ERROR CIRCUIT RELEASED BY CO-EXCHANGE DN078927 Issue 1-0 Id:0900d80580635beb 19 . SUBSCRIBER NUMBER CHANGED CONGESTION IN TERMINAL EXCHANGE CONGESTION IN INTERNATIONAL CALL CONTROLLED NOT READY NETWORK. LINE OUT OF SERVICE NETWORK. UNALLOCATED NUMBER NETWORK. Effective and ineffective cause codes DX200 Clear Code List 0A07H 0A08H 0A09H 0A0AH 0A0CH 0A0DH 0A0EH 0A0FH 0B02H 0B0FH 0B11H 0B17H 0B18H 0B19H 0B20H 0B21H 0B23H 0B2AH 0B2BH 0B2DH 0B2CH 0B2EH 0B2FH 0B30H 0B31H 0B32H 0B33H 0B34H 0B35H 0B36H 0B37H 0B38H 0B39H 0B3AH CALL FAILURE FROM OUTGOING CIRCUIT INTER-EXCHANGE SIGNALLING OUT OF ORDER ADDRESS COMPLETE MESSAGE TIME-OUT ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED NO DIGITAL TRUNK NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION NO CIRCUIT AVAILABLE IN TRANSIT NETWORK RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING TRANSIT/TERMINAL SIGNAL WAIT TIMERSUPERVISION EXCEEDED LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED MODEM COMMUNICATION ERROR ADDRESS INCOMPLETE SERVICE UNAVAILABLE SERVICE INCOMPATIBLE NETWORK ADDRESS EXTENSION (NAE) ERROR DTE IS UNCONTROLLED DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT BLOCKING RECEIVED PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED INTELLIGENT NETWORK APPLICATION RESPONSE INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR TIME-OUT MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED TCAP ERROR ASN1 CODING OR DECODING ERROR SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION CONTINUITY CHECK FAILURE A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD CALLING CARD NUMBER SELECTED BY USER NOT FOUND IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD IN FALLBACK CODE ONE IN FALLBACK CODE TWO IN FALLBACK CODE THREE 20 Id:0900d80580635beb DN078927 Issue 1-0 . 08 PROTOCOL TIMER EXPIRES DUAL LOG-IN ISDN-SUBSCRIBER FACILITY DIALLING REJECTED MANDATORY INFORMATION ELEMENT MISSING INVALID INFORMATION ELEMENT CONTENT DN078927 Issue 1-0 Id:0900d80580635beb 21 .DX200 Clear Code List Effective and ineffective cause codes 0B3BH 0B3CH 0B3DH 0C00H 0C01H 0C02H 0C04H 0C05H 0C06H 0C08H 0C09H 0C0AH 0C0BH 0C0DH 0D00H 0D01H 0D03H 0D04H 0D06H 0D07H 0D08H 0D0BH 0D0FH 0D10H 0D11H IN FALLBACK CODE FIVE IN FALLBACK CODE FOUR IN DIALOG .AND B-SUBSCRIBERS BEARER CAPABILITY NOT PRESENTLY AVAILABLE SUBSCRIBER SIGNALLING MESSAGE CONTENT SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR SERVICE OR FUNCTION NOT IMPLEMENTED SUBSCRIBER SIGNALLING PROTOCOL ERROR AOCC CHARGING ERROR NO RESPONSE TO CALL ESTABLISHMENT ALERTING OR CONNECT GSM ERH 4.ROUTING FAILURE IN SS7 NETWORK DIAL WAIT TIME EXCEEDED PROHIBITED DIALLING INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER PREMATURE DIALLING SERVICE OR FACILITY ACTIVATION RESTRICTED SERVICE OR FACILITY USAGE RESTR USED INCONSISTENCY BETWEEN A. Possibility to change the default effect Not possible.2 001H . 22 Id:0900d80580635beb DN078927 Issue 1-0 . Possibility to change the default effect Not possible. the call set-up is returned to the incoming circuit.SUSPENDED CALL Text in MML printouts SUSPENDED CALL Description As the result of the digit analysis. The originating exchange connects a special information tone to the subscriber.1 000H . or both of them have made onhook. Default effect on the exchange The call is cleared in terminal and transit exchanges. 5.NORMAL END OF CALL Text in MML printouts NORMAL END OF CALL Description An outgoing or incoming call has ended faultlessly. Alarms No alarms. Detected by Default effect on the exchange Depending on the method of clearing. the call is cleared when either subscriber.Clear codes DX200 Clear Code List 5 Clear codes 5. Detected by Program block INREGI Explanation INREGI sets the clear code when the answer to the digit analysis is rou_and_cha_suspended_call. 4 004H . The originating exchange connects a busy tone to the subscriber. 5.3 003H . Detected by Default effect on the exchange The call is cleared in transit exchanges.DX200 Clear Code List Clear codes Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 23 . Possibility to change the default effect Not possible. This serves to itemize the fault cases in which the called subscriber has answered and the call was successful as concerns the exchange. 5. Detected by Default effect on the exchange The call is cleared in transit exchanges.B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT Text in MML printouts B BUSY OR CONGESTION Description Line signal B BUSY (called subscriber busy) or CONGESTION has been received from the outgoing circuit. Possibility to change the default effect Not possible. Alarms No alarms.CALL DURATION BELOW SUPERVISION TIME Text in MML printouts CALL DURAT BELOW SUP TIME Description The call has ended before the set limit. but the established connection did not satisfy the calling and called subscribers. The originating exchange connects a special information tone to the subscriber. e. or an analog subscriber is busy.g. or B DOES NOT ANSWER message or a clearing message with cause code B DOES NOT ANSWER has been received from the outgoing circuit. the call can be directed for reanalysis in tree 33H both in terminal and transit exchanges. parameter CBB). or the outgoing circuit has sent a "B SUBSCRIBER BUSY" message. The clear code prevents Call 24 Id:0900d80580635beb DN078927 Issue 1-0 .CALLED SUBSCRIBER BUSY Text in MML printouts B-SUBSCRIBER BUSY Description The called subscriber line is busy.6 006H .5 005H . Besides this. Possibility to change the default effect Using facility routing (command group RE. Detected by Program block SI6PRB Explanation SI6PRB sets the clear code when both B-channels are occupied in the signalling. Operator Intervention. Some subscriber services. The originating exchange connects a busy tone to the subscriber. or the outgoing circuit has sent a register signal or a line signal which has been interpreted as "called subscriber busy".TIME-OUT FOR B-SUBSCRIBER ANSWER Text in MML printouts B ANSWER TIME OUT Description The called subscriber's (B-subscriber) answer supervision time has expired. This clear code prevents Call Forwarding Busy (CFB) if the called subscriber rejects a call (or a waiting call) during the ringing phase. 5. Default effect on the exchange The call is cleared in terminal and transit exchanges. facility routing can be used to connect an audible tone to the incoming circuit in terminal and transit exchanges. may cause that the call set-up is continued. Alarms No alarms. 5.Clear codes DX200 Clear Code List Alarms No alarms. or a clearing message where the cause code is "B BUSY". Possibility to change the default effect Not possible. DN078927 Issue 1-0 Id:0900d80580635beb 25 .7 007H . Alarms No alarms. Alarms No alarms. Default effect on the exchange The call is cleared in terminal and transit exchanges. The waiting call is cleared. Detected by Program block TPSPRB Explanation TPSPRB sets the clear code when the subscriber has not answered a waiting call within the time supervision. Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber.CALL WAITING TIME-OUT Text in MML printouts CALL WAITING TIME OUT Description A subscriber who has the Call Waiting service has not answered a waiting call within the time supervision.DX200 Clear Code List Clear codes Forwarding on No Reply (CFNR) if the amount of call forwarding steps has been exceeded. ICXPRB or CASSIG sets the clear code when the supervision time of the called subscriber's answer has been exceeded. Detected by Program block CASSIG ICXPRB Explanation ICxPRB or CASSIG sets the clear code when the supervision time of the called subscriber's answer has been exceeded. 5. CALLED SUBSCRIBER NOT CONNECTED Text in MML printouts B NOT CONNECTED Description The called subscriber line is unallocated or not connected. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible.9 009H .8 008H . 5. Possibility to change the default effect Not possible. Detected by Program block OC6PRB Explanation OC6PRB sets the clear code when the called subscriber's data reveals that the subscriber line is unallocated or unequipped.CALL ALREADY WAITING Text in MML printouts CALL ALREADY WAITING Description An attempt has been made to call a subscriber who has currently a call waiting. Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms. 26 Id:0900d80580635beb DN078927 Issue 1-0 . Another waiting call will not be accepted. Detected by Program block TPSPRB Explanation TPSPRB sets the clear code when a call waiting attempt is made to an analog subscriber line with a call already waiting.Clear codes DX200 Clear Code List 5. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Detected by Program block TPSPRB Explanation TPSPRB sets the clear code when intervention is attempted in a case where the subscriber is already subject to intervention.11 00BH . Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. or if no calling subscriber's (A-subscriber) identification data are received from the incoming signalling.DX200 Clear Code List Clear codes Alarms No alarms.INTERVENTION ALREADY ON Text in MML printouts INTERVENTION ALREADY ON Description Intervention is attempted to a subscriber line which is already subject to intervention.10 00AH . Detected by Program block OUREGI Explanation OUREGI sets the clear code when the call is rerouted due to an absent subscriber service facility. 5. DN078927 Issue 1-0 Id:0900d80580635beb 27 .REROUTING DUE TO B-SUBSCRIBER FACILITY Text in MML printouts REROUTING DUE TO B-SUBSC Description The called subscriber (B-subscriber) has in active state a facility which directs the call to a third subscriber (C-subscriber) or to a centralized answering device by means of rerouting. The originating exchange connects a congestion tone to the subscriber. Alarms No alarms. Alarms No alarms. Possibility to change the default effect Not possible. Possibility to change the default effect Not possible. The exchange has a "crisis" operating mode on. Detected by Program block ICXPRB INREGI Explanation ICxPRB or INREGI sets the clear code when call set-up is prevented on the basis of the restriction category used in the exchange. The originating exchange connects a special information tone to the subscriber. The originating exchange sends a special information tone to the subscriber. Alarms No alarms. which prevents the call set-up.12 00CH .MALICIOUS CALL TRACING Text in MML printouts MALICIOUS CALL 28 Id:0900d80580635beb DN078927 Issue 1-0 . ICxPRB or INREGI sets the clear code when call set-up is prevented on the basis of the restriction category used in the exchange. 5.Clear codes DX200 Clear Code List Default effect on the exchange The call is cleared in transit exchanges.OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE Text in MML printouts RESTRI DUE TO CRISIS MODE Description The line signal B BUSY (called subscriber busy) or CONGESTION has been received from the outgoing circuit. Default effect on the exchange The call is cleared in terminal and transit exchanges. 5.13 00EH . TIGPRB sets the clear code when the amount of charging pulses exeeds the amount of pulses set on the intermediate report in the exchange. Default effect on the exchange After call tracing. Possibility to change the default effect Not possible. or its duration.INTERMEDIATE CHARGING Text in MML printouts INTERMEDIATE CHARGING Description An intermediate charging message is sent to the statistics when the amount of charging pulses of an ongoing call. The statistical system stores the accumulated charging pulses and the elapsed call time in specific counters.DX200 Clear Code List Clear codes Description The called subscriber has performed call tracing. ICxPRB or CASSIG sets the clear code whenthe length of the call exceeds the time supervision limit set on the intermediate report in the exchange. Alarms No alarms. the call is continued as normal. Detected by Program block CASSIG Explanation ICxPRB or CASSIG sets the clear code when the length of the call exceeds the time supervision limit set on the intermediate report in the exchange. 5.14 00FH . and they are directed to output devices defined by the user. Detected by Program block OC6PRB Explanation OC6PRB sets the clear code when the called subscriber has performed call tracing. – ICXPRB TIGPRB DN078927 Issue 1-0 Id:0900d80580635beb 29 . IGPRB sets the clear code when the amount of charging pulses exeeds the amount of pulses set on the intermediate report in the exchange. An observation report and a detailed charging record are always generated for calls ending in this clear code. has reached the preset limit. the call can be rerouted from the incoming exchange. No tone is connected to the subscriber.OPERATOR PRIORITY ACCESS Text in MML printouts OPERATOR PRIORITY ACCESS 30 Id:0900d80580635beb DN078927 Issue 1-0 . OC6PRB or OUREGI sets the clear code when the subscriber data of the called subscriber discloses that absent subscriber service is active. the call control clears the call backwards. on the basis of incoming signalling information. unallocated. Possibility to change the default effect With facility routing it is possible to connect an audible tone to the subscriber. Detected by Program block OC6PRB OUREGI Explanation OC6PRB or OUREGI sets the clear code when the subscriber data of the called subscriber discloses that absent subscriber service is active. and the call is continued as normal.ABSENT SUBSCRIBER Text in MML printouts ABSENT SUBSCRIBER Description The operation concerns a subscriber who is not registered. 5. Alarms No alarms. The originating exchange carries out a digit re-analysis in standard analysis tree 26H (command group RE.Clear codes DX200 Clear Code List Default effect on the exchange The clear code is only used in successful intermediate reporting. parameter CAS).16 011H .15 010H . Possibility to change the default effect Not possible. or not reachable. Alarms No alarms. Default effect on the exchange If. 5. the transit exchange can connect an audible tone to the subscriber.17 012H . Possibility to change the default effect Not possible. parameter CRO).NO PAGING RESPONSE Text in MML printouts NO PAGING RESPONSE Description A mobile-terminating call cannot be connected because the mobile station is not found in paging. Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms.18 013H . Detected by Program block TPSPRB Explanation TPSPRB sets the clear code when the call is cleared because of automatic operator's intervention. 5. The transit exchange carries out a digit re-analysis in tree 2EH (command group RE.CALL TRANSFER RECALL DUE TO C-SUBSCRIBER ANSWER TIME-OUT DN078927 Issue 1-0 Id:0900d80580635beb 31 . Possibility to change the default effect Using facility routing. 5. The originating exchange connects a special information tone to the subscriber. Alarms No alarms. or the clear code prevents Call Forwarding On Mobile Subscriber Not Reachable (CFNRc) due to too many call forwardings.DX200 Clear Code List Clear codes Description The call is cleared because of a priority call. Detected by Default effect on the exchange The call is cleared in originating and terminal exchanges. 19 015H . who has call transfer with recall facility.SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE 32 Id:0900d80580635beb DN078927 Issue 1-0 . Detected by Default effect on the exchange The call is cleared in transit exchanges. The clear code is sent to the incoming circuit in a clearing message (this is done only in ISUP connections).NORMAL UNSPECIFIED Text in MML printouts NORMAL UNSPECIFIED Description Facility call was successful. Alarms No alarms.20 016H .Clear codes DX200 Clear Code List Text in MML printouts CALL TRANSFER RECALL Description The calling subscriber (A-subscriber). 5. Detected by Default effect on the exchange – Possibility to change the default effect Not possible. Possibility to change the default effect Not possible. has transferred the call to a third party (C-subscriber). Time supervision expires in an exchange. The transferred call is cleared and the original call between the Asubscriber (the controlling subscriber) and the B-subscriber is re-established. Alarms No alarms. 5. but the recall timer (C-subscriber answering time) has expired. The originating exchange connects a special information tone to the subscriber. which connects an announcement in a failed call. Phase charging is removed and intermediate charging message is sent to the statistics.21 018H .INTERMEDIATE CHARGING IN THE END OF THE PHASE CHARGING Text in MML printouts INT CHRG IN PHAS CHRG END Description A service number call is returned back to the operator. 5. The call is not cleared with this code. 5. Alarms No alarms.22 020H .DX200 Clear Code List Clear codes Text in MML printouts CHA CAPA OF SUBS EXCEEDED Description The charging capacity of a subscriber has been exceeded in the exchange. but the code is saved to the CDR Detected by Default effect on the exchange – Possibility to change the default effect Not possible.ANNOUNCEMENT SUCCESS IN INTERCEPTION Text in MML printouts ANN SUCCESS IN INTERCEPT DN078927 Issue 1-0 Id:0900d80580635beb 33 . Detected by Default effect on the exchange – Possibility to change the default effect Not possible. Alarms No alarms. ICXPRB 34 Id:0900d80580635beb DN078927 Issue 1-0 . The ICXPRB program block sets this clear code when call rerouting has occured in the QSIG call forwarding. the Subscriber Observation report (SO). New connection to the new destination has been established. The initial disconnect clear code is always shown in call reports and in the unsuccessful call CDR if it is made.Clear codes DX200 Clear Code List Description In case of a successful interception announcement. which has invoked the Call Drop Back.23 025H . The CREPRB program block sets this cause code when it releases the old connection towards the node. Alarms No alarms. Default effect on the exchange The call is cleared.CALL DROP BACK RELEASE Text in MML printouts CALL DROP BACK RELEASE Description The call has been released due to the Call Drop Back function or due to the rerouting in call forwarding invoked by the Service Node or Voice Prosessing type of node. Detected by Program block ICXPRB Explanation Either the IC1PRB. New connection to the new destination has been established. IC3PRB or IC6PRB sets this clear code when the interception announcement is given successfully. the ICC sets the clear code ANN SUCCESS IN INTERCEPT (0020H) and sends it to statistics and charging. If detailed charging (DC) is set in the interception tree. Otherwise only the initial clear code is shown. Possibility to change the default effect Not possible. which has invoked the Call Drop Back. two clear codes are shown in the Call Detailed Charging report (CDR).The ICXPRB program block sets this clear code when call rerouting has occured in the QSIG call forwarding. Detected by Program block CREPRB Explanation The CREPRB program block sets this cause code when it releases the old connection towards the node. and the trafficability performance reports. 5. DX200 Clear Code List Clear codes Default effect on the exchange This clear code is sent forward to the network. 5. DN078927 Issue 1-0 Id:0900d80580635beb 35 . Possibility to change the default effect Not possible.24 031H .CIRCUIT RE-SEIZED Text in MML printouts CIRCUIT RE-SEIZED Description When a single circuit stays occupied in statistics and the circuit is re-seized. Alarms No alarms. the statistics program block releases the old call record before the new seizure is accepted in the statistics. Default effect on the exchange The originating exchange connects a tone or an announcement defined in EOS-analyse to the subscriber. 5.NOT ENOUGH CREDIT TO CALL Text in MML printouts NOT ENOUGH CREDIT Description The calling party does not have enough credit to make a call. Alarms No alarms. Detected by Program block TIGPRB Explanation TIGPRB sets the code when the calling subscriber does not have enough credit for a call.25 100H . Possibility to change the default effect Not possible. Alarms No alarms. Default effect on the exchange No effect on the call set-up. Detected by Program block CGPROC STPROC Explanation CGPROC or STPROC sets the clear code when the order of statistics messages in the call is not logical. Default effect on the exchange No effect on the call set-up. Possibility to change the default effect No effect on the call set-up.CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE Text in MML printouts CIRCUIT RELEASE BEF "END" Description Messages INCOMING CIRCUIT RELEASED' or 'OUTGOING CIRCUIT RELEASED' have been received before the end of the call notice. 5. Possibility to change the default effect No effect on the call set-up.26 101H .CALL RECORD RELEASED DURING CALIBRATION 36 Id:0900d80580635beb DN078927 Issue 1-0 . CGPROC or STPROC sets the clear code when the order of statistics messages in the call is not logical.Clear codes DX200 Clear Code List Detected by Program block STPROC Explanation STPROC sets the clear code when a reserved call record is subject to a new reservation.27 102H . Alarms No alarms. 5. DX200 Clear Code List Clear codes Text in MML printouts CALL RECORD REL DURING CA Description When calibrating the traffic measurement files.CALL RELEASED Text in MML printouts CALL RELEASED DN078927 Issue 1-0 Id:0900d80580635beb 37 . the statistical program block has detected a circuit which is not included in the marker files even though the statistics files indicate that the circuit is seized. Alarms No alarms. Detected by Default effect on the exchange No effect on the call set-up. Detected by Default effect on the exchange No effect on the call set-up. Possibility to change the default effect No effect on the call set-up. Alarms No alarms. Possibility to change the default effect No effect on the call set-up. The statistics system releases the circuit. 5.29 201H .28 103H .CHARGING IN WRONG PHASE OF CALL Text in MML printouts CHARGING IN WRONG PHASE Description The statistical program block has received a charging message for a call in a phase where the message cannot be accepted. 5. CASSIG sets the clear code when the following line signals are received from LIRECE.30 202H . or SPECIAL_TRAFFIC_TYPE. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange sends a special information tone to the subscriber.CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT Text in MML printouts CLEAR REQUEST RECEIVED Description A clear request or an equivalent signal or message has been received from the outgoing circuit. Detected by Program block CASSIG Explanation CASSIG sets the clear code when the B-ONHOOK signal is intercepted in conversation state and yet charging has been defined for the the incoming circuit. Within this time the B-ONHOOK can be intercepted. 38 Id:0900d80580635beb DN078927 Issue 1-0 . SPECIALLY_LONG_SIGNAL_BEGUN. Default effect on the exchange The call is cleared in terminal and transit exchanges.Clear codes DX200 Clear Code List Description The outgoing signalling has received an unknown line signal or an unknown message in reply to the seizure. Alarms No alarms. The B-subscriber can continue a call after hanging up (B-ONHOOK) by picking up the receiver within the limits of the time supervision. The originating exchange connects a congestion tone to the subscriber. Detected by Program block CASSIG Explanation CASSIG sets the clear code when an unknown message is received in reply to the seizure. The conversation state is maintained for the time allowed by the time supervision. A call in the call phase is cleared. CLEAR-REQUEST. Possibility to change the default effect Not possible. 'B-ONHOOK signal intercepted' means this. 5. Detected by Default effect on the exchange The outgoing circuit is hunted again. Alarms No alarms.ESTABLISHED B-CHANNEL Text in MML printouts ESTABLISHED B CHANNEL Description The call set-up is attempted on a channel which is occupied by another call (other calls). The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible.32 204H .B-CHANNEL UNACCEPTABLE Text in MML printouts B CHANNEL UNACCEPTABLE Description The terminal equipment of an ISDN subscriber does not accept the B-channel offered by the exchange. 5. 5.DX200 Clear Code List Clear codes Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block Explanation 2B+D terminal equipment.31 203H . Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 39 . The number of hunting attempts is indicated in the outgoing signalling record. Seen from the exchange. The originating exchange connects a congestion tone to the subscriber.CALL REJECTED Text in MML printouts CALL REJECTED Description The call is rejected by an ISDN subscriber's terminal equipment. 5. Detected by - 40 Id:0900d80580635beb DN078927 Issue 1-0 .34 207H . Detected by Program block Explanation ISDN terminal equipment.Clear codes DX200 Clear Code List Possibility to change the default effect Not possible. the call is successful. Alarms No alarms. since the terminal equipment is neither busy nor incompatible. 5. Alarms No alarms. Default effect on the exchange The call is cleared in transit exchanges.SUBSCRIBER CONGESTION Text in MML printouts SUBSCRIBER CONGESTION Description The terminal equipment of an ISDN subscriber has informed the exchange that the resources needed for call reception are not available.33 206H . Possibility to change the default effect Not possible. A-subscriber's line out of service. Alarms No alarms.35 20BH . Alarms No alarms. i. Possibility to change the default effect Not possible.e.CLEAR IN DETAILED CHARGING Text in MML printouts CLEAR IN TOLL TICKETING Description Detailed charging has been defined for the outgoing circuit group.DX200 Clear Code List Clear codes Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. DN078927 Issue 1-0 Id:0900d80580635beb 41 . Possibility to change the default effect Not possible.36 20EH . 5. the files indicate that the position number is vacant. The originating exchange connects a special information tone to the subscriber. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. and the signalling of the incoming circuit group does not allow for an interrogation of the calling subscriber's number. The data is stored in the subscriber data in the central memory. The originating exchange connects a special information tone to the subscriber.CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE Text in MML printouts A-LINE VACANT Description The calling subscriber (A-subscriber) has not been created in the exchange data. Clear codes DX200 Clear Code List Detected by Program block IC6PRB Explanation IC6PRB or INREGI (ARF) sets the clear code when there is no number created for the A-subscriber in the exchange. the call control has seized a new outgoing circuit for the call.CHANGE OF OUTGOING CIRCUIT Text in MML printouts CHANGE OF OUTG CIRCUIT Description Due to external congestion in the network. Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Alarms No alarms.NULL NUP Text in MML printouts NULL NUP 42 Id:0900d80580635beb DN078927 Issue 1-0 . 5. Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber. The clear code is set on the old circuit to be released.38 210H . 5. This situation is possible only when the release of the old circuit lasts longer than the seizure of the new one. Alarms No alarms. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.37 20FH . CPLPRB sets the clear code when the called A subscriber does not answer during CCBS recall.39 211H . Detected by Program block SI4PRB Explanation SI4PRB sets this clear code when a RELEASE message with the cause code Rejected Diverted Calls is received from a NUP circuit. Possibility to change the default effect Not possible. Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 43 .DX200 Clear Code List Clear codes Description The reason for release is either unknown or has previously been received (used in NUP signalling) or CCBS recall has not succeeded ( The called A subscriber does not answer ). REJECTED DIVERTED CALLS Text in MML printouts REJECTED DIVERTED CALLS Description Diverted calls are not accepted by the B subscriber. Detected by Program block CPLPRB SI4PRB Explanation CPLPRB sets the clear code when the called A subscriber does not answer during CCBS recall. Default effect on the exchange The call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber. SI4PRB sets the clear code when the reason for release has been received previously.NETWORK. Default effect on the exchange – Possibility to change the default effect Not possible. 5. Alarms No alarms. Clear codes DX200 Clear Code List 5. Otherwise the call is cleared in a way depending on the incoming signalling. the call is rerouted.NETWORK. The release cause is received from the network.CALL DROP BACK Text in MML printouts DROPPED CALL Description Cause code #23 (ISUP signalling) has been received from the network. Detected by Program block SI7PRB Explanation SI7PRB sets this clear code when it receives cause code #23 from the network. 44 Id:0900d80580635beb DN078927 Issue 1-0 .41 215H . Default effect on the exchange – Possibility to change the default effect Not possible. The originating exchange carries out a digit re-analysis in the interception tree 32H. Alarms No alarms. Detected by Program block SI7PRB Explanation SI7PRB sets this clear code when it has received the corresponding release cause from the network. Default effect on the exchange The call is cleared in terminal and transit exchanges. 5.40 213H . If the feature Call Drop Back is supported. USER NOT IN CUG Text in MML printouts N USER NOT IN CUG Description The subscriber is not in the closed user group. The originating exchange connects a congestion tone to a subscriber.43 217H . SI5PRB Default effect on the exchange The call is cleared in terminal and transit exhanges. 5. 5. Detected by Program block SI3PRB Explanation SI3PRB and SI5PRB set this clear code when MPR message is received from a network.MISDIALLED TRUNK PREFIX Text in MML printouts MISDIALLED TRUNK PREFIX Description Erroneous inclusion of a trunk prefix in the called party number. SI3PRB and SI5PRB set this clear code when MPR message is received from a network. the call can be re-analysed in the desired tree set by the EOS Analysis Management -MML (command group RX). the originating exchange can connect an audible tone to the calling subscriber. parameter CCF) terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 32H. If the feature Call Drop Back is in use in the exchange. Alarms No alarms.TEMPORARY OUT OF ORDER Text in MML printouts TEMPORARY OUT OF ORDER DN078927 Issue 1-0 Id:0900d80580635beb 45 . SI7PRB sets the code when cause #5 is received from a network.DX200 Clear Code List Clear codes Possibility to change the default effect Using facility routing (command group RE.42 216H . Possibility to change the default effect Not possible. SI7PRB sets the code when cause #5 is received from a network. The redirecting number received in the release message from the network is used as the routing number. Alarms No alarms. Using facility routing. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 46 Id:0900d80580635beb DN078927 Issue 1-0 .Clear codes DX200 Clear Code List Description Shows that the required subscriber line is not in service as a result of administrative action or at the request of the subscriber.44 218H . Alarms No alarms. Possibility to change the default effect Not possible. Detected by Program block SI4PRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. For this call the caller was in a disallowed catchment area.OUT OF CATCHMENT AREA Text in MML printouts OUT OF CATCHMENT AREA Description Shows that access to the destination address as given in the IAM/IFAM is dependent on the caller's catchment area (normally based on CLI). The originating exchange connects busy tone to the subscriber. 5. Detected by Program block SI4PRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects busy tone to the subscriber. Possibility to change the default effect Not possible.ANONYMOUS CALLS REJECTION Text in MML printouts ANONYMOUS CALLS REJECTION Description The called subscriber does not accept calls from subscribers who withhold their numbers from showing to the called party. Detected by Program block SI4PRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms.TRANSLATION OUT-OF-SERVICE Text in MML printouts TRANSLATION OUT OF SERVICE Description Shows that call rejection has occurred as there is temporarily no active translation for the called address. Possibility to change the default effect Not possible. Detected by Program block SI4PRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. DN078927 Issue 1-0 Id:0900d80580635beb 47 . The originating exchange connects a special information tone to the subscriber. 5.DX200 Clear Code List Clear codes 5.45 219H .46 220H . Misrouted call to a ported number.CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION Text in MML printouts OUTGOING CALLS BARRED Description A call from the calling subscriber (A-subscriber) is routed to a direction to which it has no access due to an outgoing call restriction category. Alarms No alarms.UNTERMINATED CALL TO A PORTED NUMBER Text in MML printouts UNTERMINATED PORTED CALL Description This cause code is used to release the call with ISUP REL cause 112. 48 Id:0900d80580635beb DN078927 Issue 1-0 . Originating exchange connects special tone. New cause code 112 (Ported Number not found) is Sweden specific value. 5. the the terminating network shall release the call with the cause 112. This clear code is also used if the subscribers' calls in the PABX are barred outside the local network. or as unallocated. 5. Default effect on the exchange SI7PRB (SSI) clears the call with ISUP REL cause code 112.47 252H . This barring information is stored in the central memory or in the VLR. Terminating exchange clears backwards with cause 112 Possibility to change the default effect Originating exchange can use facility routing or interception in tree 2AH.48 300H . Detected by Program block OC2PRB Explanation OC2PRB sets this clear code when HLR responded to SRI with clear code 0x307 B_number unused and the cc setup message indicates that the call is routed with Location Routing Number.Clear codes DX200 Clear Code List Alarms No alarms. The subscriber has barred the outgoing call with a supplementary service restricting outgoing calls. If terminating network receives a call with the indication of ported number but the terminating network does not recognise the called Directory Number as belonging to the network. however. Default effect on the exchange The call is cleared in terminal and transit exchanges.CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR Text in MML printouts OPER RESTR IN OUT DIRECT Description A call from the calling subscriber (A-subscriber) goes to a route to which it has no access due to outgoing call restriction activated by the operator. The originating exchange connects a special information tone to the subscriber. Alarms No alarms. Default effect on the exchange The originating exchange connects a congestion tone to the subscriber. DN078927 Issue 1-0 Id:0900d80580635beb 49 . Possibility to change the default effect Using facility routing (command group RE. Possibility to change the default effect Not possible. E. not in an exchange that has the A-validation feature. the call can be directed for reanalysis in tree 35H both in terminal and transit exchanges. In A-validation cases a tone is connected to the calling subscriber.g. The clear code can only be set in the originating exchange.DX200 Clear Code List Clear codes Detected by Program block IC6PRB Explanation IC6PRB or INREGI sets the clear code when the call set-up is barred by subscriber-specific restriction of outgoing calls.49 301H . Alarms No alarms. 5. the barring of outgoing Centrex-calls. parameter CAB). Detected by Program block IC6PRB Explanation IC6PRB sets the clear code if the call set-up is barred by the outgoing call restriction of the Centrex-subscriber. Detected by Program block OC6PRB Explanation OC6PRB or OUREGI sets the clear code. Default effect on the exchange The call is cleared in terminal and transit exchanges.50 304H . an audible tone can be connected to the subscriber. 50 Id:0900d80580635beb DN078927 Issue 1-0 . when "connection closed" has been set in the called-subscriber data. The data is stored in the subscriber data of the central memory. Detected by Program block OC6PRB Explanation OUREGI or OC6PRB sets the clear code. Alarms No alarms. INREGI sets the clear code.CALLED SUBSCRIBER LINE OUT OF SERVICE Text in MML printouts B-LINE OUT OF SERVICE Description The line of the called subscriber (B subscriber) is out of service.51 305H . The originating exchange carrºies out a digit re-analysis in interception tree Possibility to change the default effect Using facility routing. when "line faulty" has been set in the called-subscriber data. 5. when "exchange closed" has been set in the supplementary-direction data.CALLED SUBSCRIBER LINE FAULTY Text in MML printouts B-LINE FAULTY Description The line of the called subscriber (B-subscriber) is faulty. The information is in the subscriber data of the central memory. parameter CAB).Clear codes DX200 Clear Code List 5. parameter CBO). Interception tree 35H (command group RE. Interception tree 30H (command group RE. Possibility to change the default effect Using facility routing (command group RE. Using facility routing.53 307H . 5. transit and terminal exchanges can carry out a digit re-analysis in tree 2FH. Alarms No alarms. parameter CFB).B-NUMBER UNUSED DN078927 Issue 1-0 Id:0900d80580635beb 51 . and terminal and transit exchanges can carry out a digit re-analysis in tree 35H.DX200 Clear Code List Clear codes Default effect on the exchange The call is cleared in terminal and transit exchanges. and the category of the calling subscriber does not allow the bypassing of the restriction.52 306H . Possibility to change the default effect Using facility routing (command group RE. The originating exchange carries out a digit re-analysis in tree 35H. This clear code is also set when the calling and called subscribers are incompatible and the operation presupposes a call release.ACCESS TO B-SUBSCRIBER LINE RESTRICTED Text in MML printouts B-CALLS RESTRICTED Description Access to the B-subscriber line (called line) is restricted. or restricted access to the B-subscriber (RAB). Alarms No alarms. Default effect on the exchange The call is cleared in terminal and transit exchanges. or connect an audible tone to the subscriber. the originating exchange and connect an audible tone to the subscriber. parameter CAB). or connect an audible tone to the subscriber. the originating exchange can connect an audible tone to the subscriber. The called subscriber has prevented the incoming call with a supplementary service. The information is set in the subscriber data of the central memory or in the HLR. OUREGI or OC1PRB sets the clear code when the call set-up is not possible due to incoming call barring (ICB) of the called subscriber. 5. The originating exchange carries out a digit re-analysis in tree 2FH. Detected by Program block OC6PRB Explanation OC6PRB. Alarms No alarms. Detected by Program block ICXPRB Explanation ICxPRB or INREGI sets the clear code when information is received from the digit analysis that the analysed number is unused.B-NUMBER CHANGED Text in MML printouts B-NUMBER CHANGED Description The central memory's answer to the digit analysis by the register is NUMBER CHANGED. parameter CUN). The originating exchange carries out a digit re-analysis in tree 2AH. terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2AH. Detected by Program block ICXPRB Explanation ICxPRB or INREGI sets the clear code when information is received from the digit analysis that the number of the called subscriber has changed.54 308H . 5. Default effect on the exchange The call is cleared in terminal and transit exchanges. Default effect on the exchange The call is cleared in terminal and transit exchanges.Clear codes DX200 Clear Code List Text in MML printouts B-NUMBER UNUSED Description The central memory's answer to the digit analysis is B-NUMBER UNUSED. The originating exchange carries out a digit re-analysis in tree 29H. Possibility to change the default effect Using facility routing (command group RE. 52 Id:0900d80580635beb DN078927 Issue 1-0 . the originating exchange can connect an audible tone to the subscriber. Using facility routing. Detected by Program block CASSIG Explanation CASSIG sets the clear code if the operator calls an engaged line and an intervention tone is not received within the time supervision. terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 29H. Possibility to change the default effect Not possible.CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE Text in MML printouts A ONHOOK DURING SET UP Description The connection has been cleared in the set-up phase either due to a calling subscriber onhook or because a signal or a message equivalent to clearing has been received from the incoming circuit. 5.56 30AH .TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION Text in MML printouts WAIT FOR INTERV TIME OUT Description An intervention signal has not arrived before time-out. parameter CSN). Alarms No alarms. Using facility routing. 5. Default effect on the exchange The call is cleared in terminal and transit exchanges.DX200 Clear Code List Clear codes Possibility to change the default effect Using facility routing (command group RE. The originating exchange connects a congestion tone to the subscriber. the originating exchange can connect an audible tone to the calling subscriber. DN078927 Issue 1-0 Id:0900d80580635beb 53 . Alarms No alarms.55 309H . Possibility to change the default effect Not possible.CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER Text in MML printouts A ONHOOK DUR_WAIT ANSWER Description Onhook by the calling subscriber (A-subscriber) has taken place before the called subscriber (B-subscriber) has answered.57 30BH . or a signal or message equivalent to clearing has been received from the incoming circuit.REANSWER TIME OUT 54 Id:0900d80580635beb DN078927 Issue 1-0 . Detected by Program block SIXPRB Explanation CASSIG. 5. 5.Clear codes DX200 Clear Code List Detected by Program block SIXPRB Explanation SIxPRB or CASSIG sets the clear code when the calling subscriber makes onhook before the end-of-selection information is received. the calling subscriber makes onhook before the called subscriber has answered. Alarms No alarms. An audible tone will not be connected because of subscriber onhook. Default effect on the exchange The call is cleared. Alarms No alarms.58 30CH . SIxPRB or ICxPRB sets the clear code when. after the end-ofselection information has been received. An audible tone will not be connected because of subscriber onhook. Default effect on the exchange The call is cleared. Possibility to change the default effect Not possible. DX200 Clear Code List Clear codes Text in MML printouts REANSWER TIME OUT Description The calling/called subscriber has not answered within the time supervision. Such services are Abbreviated Dialling. Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 55 .B. Detected by Program block IC6PRB Explanation IC6PRB. 5. The terminating exchange connects a congestion tone to the subscriber. Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible.OR C-NUMBER IS NOT REGISTERED Text in MML printouts B-NUMB IS NOT REGISTERED Description The number related to the service is not found in the central memory. OUREGI or CFOPRB sets the clear code when the Bsubscriber number connected with the subscriber facility is not obtained from the subscriber database. INREGI.59 30DH . The originating exchange connects a busy tone to the subscriber who has not made onhook. Fixed Destination Call and Call Diversion. Detected by Program block ICXPRB Explanation CASSIG or ICxPRB sets the clear code if the subscriber has not reanswered within the time limit. 56 Id:0900d80580635beb DN078927 Issue 1-0 .61 30FH . an audible tone can be connected to the subscriber using facility routing. interception tree 2FH (command group RE. a digit reanalysis is performed in the announcement tree. Detected by Program block SI6PRB Explanation The SI6PRB sets the clear code when the AICPRB informs that the subscriber is in line blocking state. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 35H. In the originating exchange. 5. Possibility to change the default effect By using facility routing. parameter CFB). Default effect on the exchange The call is cleared in terminal and transit exchanges. The OUREGI sets the clear code when the ARF subscriber line is in line blocking state. Interception tree 35H (command group RE. In the originating exchange.60 30EH . Alarms No alarms. 5. parameter CAB).Clear codes DX200 Clear Code List Alarms No alarms.CALLED SUBSCRIBER LINE BLOCKED Text in MML printouts B-LINE BLOCKED Description The called subscriber (B-subscriber) is in line blocking state. the call can be directed for a reanalysis in an interception tree in both terminal and transit exchanges.CHANGE IN NUMBERING PLAN Text in MML printouts CHANGE IN NUMBER PLANNING Description The digit analysis indicates that the numbering plan for the outgoing direction has changed. The originating exchange can connect an audible information tone to the subscriber using facility routing. parameter CNP).DX200 Clear Code List Clear codes Detected by Program block ICXPRB Explanation IC1PRB. Possibility to change the default effect Using facility routing. 5.63 311H . Alarms No alarms. Detected by Default effect on the exchange The selected number is re-analysed in tree 35H (command group RE. IC3PRB.62 310H . an audible tone can be connected to the calling subscriber. parameter CAB). in ISDN calls this clear code may indicate that access to a specified closed user group is barred. the terminal and transit exchanges can perform a reanalysis of the dialling in the tree 2BH or connect an audible information tone to the subscriber. Alarms No alarms. IC6PRB. For example. The originating exchange performs a reanalysis of the dialling using the tree 2BH (command group RE.CLOSED USER GROUP RESCTRICTION Text in MML printouts CUG REJECT Description The location register (LR) indicates that the call did not pass the CUG check or that the CUG barring conditions were transgressed. Possibility to change the default effect Using facility routing.BEARER SERVICE NOT PROVIDED Text in MML printouts BEARER SERV NOT PROV DN078927 Issue 1-0 Id:0900d80580635beb 57 . INREGI Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. the originating exchange can connect an audible tone to the subscriber. Detected by Program block SI5PRB Explanation SI5PRB.TELESERVICE NOT PROVIDED Text in MML printouts TELE SERV NOT PROV Description The subscriber has not subscribed to the teleservice defined for the call. Alarms No alarms. Alarms No alarms. Possibility to change the default effect Not possible. terminal and transit exchanges can carry out a digit re-analysis in tree 34H. Possibility to change the default effect Using facility routing. 5.64 312H . Default effect on the exchange The originating exchange carries out a digit re-analysis in tree 32H (command group RE.CALLED SUBSCRIBER HAS CALL DIVERSION BARRING 58 Id:0900d80580635beb DN078927 Issue 1-0 . or the GSM BCIE is faulty. The originating exchange connects a special information tone to the subscriber.65 315H . The call is cleared in terminal and transit exchanges. parameter CCF). 5. Using facility routing (command group RE. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. or the GSM BCIE is faulty.Clear codes DX200 Clear Code List Description The subscriber has not subscribed to the bearer service defined for the call. parameter CST). or connect an audible tone to the subscriber. IC3PRB sets the clear code when call diversion involves a manual answering service. Default effect on the exchange The call is cleared in terminal and transit exchanges. Call diversion barring is set in the subscriber data of the called subscriber.66 317H . The number of diversions per call exceeds the set limit. The originating exchange carries out a digit re-analysis in tree 35H. The originating exchange connects a special information tone to the subscriber. DN078927 Issue 1-0 Id:0900d80580635beb 59 . Detected by Program block IDXSCP Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. 2. parameter CBB).DX200 Clear Code List Clear codes Text in MML printouts B HAS CALL DIVERS BARRING Description 1. but the subscriber data indicates that call diversion to the subscriber is not allowed. Detected by Program block OC6PRB Explanation OC6PRB or OUREGI sets the clear code when the call is diverted. 5. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 35H. The terminal and transit exchanges can carry out a digit re-analysis in tree 35H.TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE Text in MML printouts IN SERVICE TIME EXCEEDED Description The overall time limit of an intelligent network (IN) based subscriber service has been exceeded. the originating exchange can connect an audible tone to the subscriber. Possibility to change the default effect Using facility routing (command group RE. Alarms No alarms. the IC1PRB.Clear codes DX200 Clear Code List Possibility to change the default effect Not possible.67 31AH . 5. 5. 60 Id:0900d80580635beb DN078927 Issue 1-0 . the IC2PRB or the IC3PRB sets this clear code if the HLR returns information that incoming calls are barred within the CUG. Default effect on the exchange The call is cleared in terminal and transit exchanges.INCOMING CALLS BARRED WITHIN THE CUG Text in MML printouts CUG REJ IC CALL BARRED Description The call is rejected because of an incoming call barring within the closed user group (CUG). Possibility to change the default effect Not possible.SUBSCRIBER NOT A MEMBER OF THE CUG Text in MML printouts CUG REJ NOT MEMBER Description The call is rejected because the subscriber is not a member of the closed user group (CUG). The originating exchange connects a congestion tone to the subscriber. Detected by Program block ICXPRB Explanation In a mobile terminating call. Alarms No alarms.68 31CH . Alarms No alarms. In a PBX terminating call.DX200 Clear Code List Clear codes Detected by Program block ICXPRB Explanation In a mobile terminating call. The called party CUG check fails because the called party does not belong to the same CUG with the calling party.69 31DH . Detected by Program block ICXPRB Explanation The IC2PRB sets this clear code if the VLR returns information that outgoing calls are barred within the CUG. 5. Default effect on the exchange – Possibility to change the default effect Not possible. the IC1PRB. and the calling party does not use outgoing access or the called party does not have incoming access. Alarms No alarms. Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 61 .OUTGOING CALLS BARRED WITHIN THE CUG Text in MML printouts CUG REJ OG CALL BARRED Description The call is rejected because of an outgoing call barring within the closed user group (CUG). the IC2PRB or the IC3PRB sets this clear code if the HLR or the VLR returns information that the subscriber is not a member of the CUG. the OC1PRB sets this clear code if the called PBX is not a member of the CUG. Default effect on the exchange – Possibility to change the default effect Not possible. 62 Id:0900d80580635beb DN078927 Issue 1-0 . In mobile originating calls this information is used in three different situations.NO CUG SELECTED Text in MML printouts CUG REJ NO CUG SELECTED Description The call is rejected because no closed user group (CUG) has been selected. In a PBX originating call. Alarms No alarms.70 321H .UNKNOWN CUG INDEX Text in MML printouts CUG REJ UNKNOWN CUG IND Description The call is rejected because the index of the closed user group (CUG) is unknown. first. if the calling subscriber does not provide the CUG index in the call setup although there is no outgoing access. if the calling subscriber has an outgoing access but no preferred CUG. the IC2PRB sets this clear code if the VLR returns information that there is no CUG selected. 5.71 322H . and a preferred CUG is not defined. Detected by Program block ICXPRB Explanation In a mobile originating call.Clear codes DX200 Clear Code List 5. and third. second. the IC1PRB sets this clear code when the preferential CUG has not been defined in the PBX. Default effect on the exchange – Possibility to change the default effect Not possible. if the calling subscriber tries to suppress the preferred CUG and there is no outgoing access. but tries to suppress the outgoing access and does not provide a CUG index in call setup. Alarms No alarms. Alarms No alarms.73 401H . Default effect on the exchange – Possibility to change the default effect Not possible. Possibility to change the default effect Not possible.DX200 Clear Code List Clear codes Detected by Program block ICXPRB Explanation The IC2PRB sets this clear code if the VLR returns information that the closed user group index is unknown.72 400H .ATTENUATOR CONGESTION Text in MML printouts ATTENUATOR CONGESTION Description Attenuator seizure ended in congestion. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. The originating exchange connects a special information tone to the subscriber. 5. DN078927 Issue 1-0 Id:0900d80580635beb 63 .INTERWORKING UNIT CONGESTION Text in MML printouts INTERW UNIT CONGESTION Description There are no free circuits available in the interworking unit. The call is rejected because a calling subscriber makes the call with a CUG index which is unknown for the subscriber. Alarms No alarms. Detected by Program block IC6PRB Explanation IC6PRB or INREGI sets the clear code when the total time limit for the call setup(ie the time from the call beginning to the end-of-selection information) is exceeded. INREGI Default effect on the exchange The call is cleared in transit exchanges. Possibility to change the default effect Not possible. the time limit for the MFC device has been exceeded in the MFST plug-in unit. 64 Id:0900d80580635beb DN078927 Issue 1-0 . Alarms No alarms. Possibility to change the default effect Not possible. For example. IC6PRB or INREGI sets the clear code when the total time limit for the call set-up (ie the time from the call beginning to the end-of-selection information) is exceeded.REGISTER TOTAL TIME EXCEEDED Text in MML printouts REGISTER TOTAL TIME EXC Description The total time limit for the call set-up has been exceeded.74 402H . The originating exchange connects a congestion tone to the subscriber. 5.Clear codes DX200 Clear Code List Detected by Program block ASEPRB SREPRB Explanation – – Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. The originating exchange connects a special information tone to the subscriber. 5.75 403H . Possibility to change the default effect Not possible. DN078927 Issue 1-0 Id:0900d80580635beb 65 .DX200 Clear Code List Clear codes 5.PBRU DEVICE CONGESTION Text in MML printouts PBRU CONGESTION Description No free PBRU devices available.MFCU DEVICE CONGESTION Text in MML printouts MFCU CONGESTION Description No free MFCU devices available. Alarms No alarms. Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal and transit exchanges.76 404H . Detected by Program block SI6PRB Explanation SI6PRB sets the clear code when ACSERV reports that the reservation of the PBRU device failed. Detected by Program block INREGI Explanation INREGI or OUREGI sets the clear code when ACSERV reports that the reservation of the MFCU device failed. The originating exchange connects a special information tone to the subscriber. Default effect on the exchange The call is cleared in terminal and transit exchanges. or the SWICOP program block.77 405H . 66 Id:0900d80580635beb DN078927 Issue 1-0 . 5. or the response is that the connection has failed. Detected by Program block ASEPRB IC3PRB IDOPRB RMAPRB Explanation ASEPRB IC3PRB IDOPRB RMAPRB – – – Default effect on the exchange The call is cleared in terminal and transit exchanges.78 406H . The originating exchange connects a special information tone to the subscriber.Clear codes DX200 Clear Code List Alarms No alarms. Alarms No alarms. Possibility to change the default effect Not possible. This clear code is used with connections which are not performed to the SSW switching network of a DX 220 exchange. The program block which requested for the connection has not been able to contact the marker.CONNECTION FAILED IN GSW/SWI Text in MML printouts CONNECT FAILED IN GSW/SWI Description The connection to the GSW switching network of a DX 220 exchange or to the SWI switching network of a DX 210 exchange needed for call set-up has failed. has not responded within the time limit. or the request was received in a wrong phase of the call. or the RMAPRB program block.ERRONEOUS SERVICE REQUEST FROM COPROCESS Text in MML printouts ERR REQUE FROM COPROCESS Description A program block has received a service request containing erroneous or missing parameters. 5. LHSPRB.DX200 Clear Code List Clear codes Detected by Program block INREGI Explanation INREGI or OUREGI sets the clear code when SWICOP sends the 4130 or 4129 message in response. OC6PRB. signalling services.ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK Text in MML printouts ERR ANSWER FROM CO-PROC Description An unknown or erroneous message has been received from the program block acting as the partner of a program block belonging to one of the following system blocks: call control. CPLPRB. or when SCRPRB gives no response at all. SI7PRB. SREPRB. IDOPRB. The originating exchange connects a special information tone to the subscriber. INREGI. Alarms No alarms. Possibility to change the default effect Not possible. SI5PRB. ASEPRB. 5. SI6PRB.79 407H . OC1PRB. Default effect on the exchange The call is cleared in terminal and transit exchanges. OUREGI. Detected by Program block ASEPRB Explanation The following programs set the clear code when the response to a service request is that the service is not available. – – – – – – – – – CFOPRB CPLPRB GCAPRB IDOPRB INREGI LHSPRB OC1PRB OC6PRB OUREGI DN078927 Issue 1-0 Id:0900d80580635beb 67 . or switching services. GCAPRB. CFOPRB. The originating exchange connects a special information tone to the subscriber.LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED Text in MML printouts B-NUMBER LENGTH EXCEEDED Description The length of the called subscriber's (B-subscriber) number has been exceeded. Alarms No alarms. Possibility to change the default effect Not possible. Detected by Program block ICXPRB INREGI Explanation ICxPRB or INREGI sets the clear code when saving the selected number fails due to overflow.80 408H . The originating exchange connects a congestion tone to the subscriber. 68 Id:0900d80580635beb DN078927 Issue 1-0 . – Default effect on the exchange The call is cleared in terminal and transit exchanges. and the call control cannot perform a digit analysis. Alarms No alarms.Clear codes DX200 Clear Code List Program block SI5PRB SI6PRB SI7PRB SREPRB Explanation – – – – Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. 5. – Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. DN078927 Issue 1-0 Id:0900d80580635beb 69 . Alarms No alarms. This clear code is used for connections performed to the SSW switching network of a DX 220 exchange.DX200 Clear Code List Clear codes 5.81 409H . The program block which requested for the connection receives an answer from the marker on the connection failure.CIRCUIT CONGESTION DUE TO TRAFFIC TYPE Text in MML printouts TRAFFIC TYPE CONGESTION Description Traffic type congestion which is caused by selective circuit congestion or automatic congestion control.82 40AH . Possibility to change the default effect Not possible. Detected by Program block INREGI OUREGI Explanation INREGI or OUREGI sets the clear code when the MFCU cannot be reserved within the time supervision.CONNECTION FAILED IN SSW/SWI Text in MML printouts CONNECT FAILED IN SSW/SWI Description There has been a failure in making the connection to the SSW switching network of a DX 220 exchange. The originating exchange connects a special information tone to the subscriber. Detected by Program block SI7PRB Explanation SI7PRB releases the call and sets #25 cause code. Default effect on the exchange – Possibility to change the default effect Not possible. This occurs when selective circuit reservation or automatic congestion control rejection percentages cause the outgoing circuit reservation to fail. 5. which is decreased in every intermediate exchange. The hop counter has an initial (maximal) value. Default effect on the exchange The call is released. Hop counter exhausts in the exchange.Clear codes DX200 Clear Code List Detected by Program block RMAPRB Explanation RMAPRB sets the clear code when SWICOP returns the error code indicating that traffic type congestion has occurred in message congestion_on_route_s (4132). 70 Id:0900d80580635beb DN078927 Issue 1-0 . Alarms No alarms. In both features the rejection percentages and continuation instructions for different traffic types (direct routed calls and alternatively directed calls) are defined. The hop counter helps to prevent looping between networks in the multicarrier environment.HOP COUNTER EXHAUST Text in MML printouts HOP COUNTER EXHAUST Description Error in routing. In automatic congestion control the rejection percentages are applied when the congestion level information has been received from the signalling point of the exchange to which the call is being routed. the call is cleared and an alarm is given. Possibility to change the default effect Not possible. In selective circuit reservation the rejection percentages are applied after the user-defined threshold values have been reached.83 40BH . When it becomes zero. Detected by Program block ICXPRB Explanation ICxPRB sets the clear code if the charging interface (CHRG_IF) reports that there has been a failure in performing the requested operation. The originating exchange carries out a digit re-analysis in tree 35H.DX200 Clear Code List Clear codes Alarms 1206 5.85 508H . Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Using facility routing (command group RE.84 506H . Using facility routing. the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 35H. the originating exchange can connect an audible tone to the subscriber. The error may have been caused by a metering pulse of deviating length or by a wrong format in the charging message.LINES OF LINE HUNTING GROUPS BARRED Text in MML printouts LINES OF LINE HUNT GROUPS Description All lines of the line hunting group acting as the B-subscriber have been barred from hunting. DN078927 Issue 1-0 Id:0900d80580635beb 71 .CHARGING ERROR Text in MML printouts CHARGING ERROR Description There has been an error in establishing charging during the call. This information is included in the data of all lines in the hunting group. parameter CAB). 5. Alarms No alarms. Possibility to change the default effect Not possible.FILE ERROR Text in MML printouts FILE ERROR Description A program block belonging to the call control system block or to the signalling services system block has found that the contents of a file is faulty or that the reading of the file has failed. Possibility to change the default effect Not possible. 72 Id:0900d80580635beb DN078927 Issue 1-0 .Clear codes DX200 Clear Code List Default effect on the exchange The call is cleared in terminal and transit exchanges.86 509H . The originating exchange connects a special information tone to the subscriber. 5. Alarms No alarms. 5.87 50BH . Detected by Program block Explanation Program blocks set the clear code if the opening of a file or access to a file fails. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Alarms No alarms.MODULE ROUTE OR SSW CONGESTION Text in MML printouts MODULE ROUTE OR SSW CONG Description Congestion in the subscriber stage. Default effect on the exchange The call is cleared in terminal and transit exchanges. or connect an audible tone to the subscriber. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.DX200 Clear Code List Clear codes Detected by Program block OUREGI Explanation OUREGI (ARF) sets the clear code when the seizure of an outgoing circuit fails. Alarms No alarms.FACILITY CONTROL FAILED Text in MML printouts FACILITY WRITING FAILED DN078927 Issue 1-0 Id:0900d80580635beb 73 . Possibility to change the default effect Using facility routing (command group RE.MFC-ASS-CHANNEL CLOSING MISSED Text in MML printouts MFC-ASS-CHAN CLOSE MISSED Description The closing command of the MFC-ASS channel has not been acknowledged within the time limit. The originating exchange carries out a digit re-analysis in tree 35H. the originating exchange and connect an audible tone to the subscriber. Alarms No alarms.89 50DH . parameter CAB). The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. 5.88 50CH . and terminal and transit exchanges can carry out a digit re-analysis in tree 35H. 5. 5. Detected by Program block OUREGI Explanation OUREGI sets the clear code when the activation of a facility fails in the ARF signalling because CMSUBS cannot update the facility data in the subscriber database. Detected by Program block SI6PRB Explanation SI6PRB sets the clear code when the module software reports that the seized time slot is in use already. Alarms No alarms. This applies only to the subscriber modules SUB and SUB-C. Alarms No alarms. Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber. This applies only to subscriber modules in a remote subscriber stage. Default effect on the exchange The call is cleared in terminal and transit exchanges. Default effect on the exchange The call is cleared in terminal and transit exchanges. 74 Id:0900d80580635beb DN078927 Issue 1-0 . Possibility to change the default effect Not possible.UNSUITABLE MODULE CIRCUIT Text in MML printouts UNSUITABLE MODULE CIRCUIT Description The hunted module circuit does not fit the subscriber module.Clear codes DX200 Clear Code List Description The activation or deactivation of a service has failed because there has been a failure in updating the service data in the central memory. The originating exchange connects a special information tone to the subscriber.90 50FH . 91 600H .MODULE OR V5 CONGESTION Text in MML printouts MOD OR V5 LINK CONGESTION Description No free module or V5 link(multiplexer) circuits are available. Typical cases are the reservations of the circuit records by SUBSIG or DACSIG in connection with a new call.DX200 Clear Code List Clear codes 5. 5. Possibility to change the default effect Not possible. Detected by Program block SI2PRB SI6PRB Explanation – – DN078927 Issue 1-0 Id:0900d80580635beb 75 .1 interface if circuit reservation fails or if error situation is detected by V5 control protocol. Alarms No alarms. SI2PRB sets this clear code in the V5.92 601H . Detected by Program block SI6PRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.FILE RECORD CONGESTION Text in MML printouts FILE RECORD CONGESTION Description A program block in the call control system block or in the signalling services system block has not been able to reserve the necessary dynamic record for a call. Alarms No alarms.93 602H . Possibility to change the default effect Not possible. Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber. 76 Id:0900d80580635beb DN078927 Issue 1-0 .94 603H .Clear codes DX200 Clear Code List Default effect on the exchange The call is cleared in terminal and transit exchanges. Default effect on the exchange The call is cleared in terminal and transit exchanges.NO RESPONSE FROM PARTNER PROGRAM BLOCK Text in MML printouts NO RESPONSE FROM CO-PROC Description A program block in the call control system block or in the signalling services system block has not been able to contact the partner block. 5.REGISTER CONGESTION Text in MML printouts REGISTER CONGESTION Description No free register is found during the register hunting phase. The partner program block has not answered within the set time. 5. Detected by Program block CASSIG Explanation CASSIG sets the clear code when INREGI reports that the reservation of a register record has failed. The originating exchange connects a special information tone to the subscriber. or no connection has been established to the unit in question. Alarms No alarms. DX200 Clear Code List Clear codes Detected by Program block ASEPRB Explanation The following program blocks set the clear code when a service request receives no response within the time limit; ASEPRB, CASSIG, CFOPRB, CPLPRB, GCAPRB, IC1PRB, IC3PRB, IC6PRB, IDOPRB, IDXSCP, INREGI, LHSPRB, OC1PRB, OC3PRB, OC6PRB, OUREGI, RMAPRB, SI1PRB, SI5PRB, SI6PRB, SI7PRB and TPSPRB. – – – – – – – – – – – – – – – – – – – – – CASSIG CFOPRB CPLPRB GCAPRB IC1PRB IC3PRB IC6PRB IDOPRB IDXSCP INREGI LHSPRB OC1PRB OC3PRB OC6PRB OUREGI RMAPRB SI1PRB SI5PRB SI6PRB SI7PRB TPSPRB Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.95 604H - INTERNAL CALL LINK CONGESTION DN078927 Issue 1-0 Id:0900d80580635beb 77 Clear codes DX200 Clear Code List Text in MML printouts INT. CALL LINK CONGESTION Description No free internal call links are available. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.96 606H - CONFERENCE DEVICE CONGESTION Text in MML printouts CONFERENCE DEV.CONGESTION Description No free conference devices are available. Conference devices are used when the operator intervenes in a proceeding call. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.97 607H - POLARITY REVERSAL FAILURE Text in MML printouts POLARITY REVERSAL FAILURE 78 Id:0900d80580635beb DN078927 Issue 1-0 DX200 Clear Code List Clear codes Description The polarity reversal relay is broken. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.98 608H - CHARGING NOT STARTED Text in MML printouts CHARGING NOT STARTED Description Starting of charging has failed. Detected by Program block CASSIG ICXPRB TPSPRB Explanation ICxPRB, TPSPRB or CASSIG sets the clear code when starting of charging fails. ICxPRB, TPSPRB or CASSIG sets the clear code when starting of charging fails. – Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.99 609H - CALL CLEARED BY MML DN078927 Issue 1-0 Id:0900d80580635beb 79 Clear codes DX200 Clear Code List Text in MML printouts CALL CLEARED BY MML Description The call has been cleared because of an operation and maintenance command. Detected by Program block SI6PRB Explanation SI6PRB sets the clear code when the ticket service prevents the call setup. Alarms No alarms. – Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block CASSIG SIXPRB Explanation CASSIG or SIxPRB sets the clear code when message forced_clear is received. New seizures cannot be received.OVERLOAD CONGESTION Text in MML printouts OVERLOAD CONGESTION Description The call set-up has been interrupted due to an overload of the unit or the entire exchange. The originating exchange connects a special information tone to the subscriber. 5. Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal. transit and originating exchanges.100 60BH . 80 Id:0900d80580635beb DN078927 Issue 1-0 . Alarms No alarms. Possibility to change the default effect Not possible. UNIT RESTARTED Text in MML printouts UNIT RESTARTED Description The call was cleared after the restart of the own unit.103 60FH . CALL CLEARED DN078927 Issue 1-0 Id:0900d80580635beb 81 .DX200 Clear Code List Clear codes 5.STAGE CIRCUIT CONGESTION Text in MML printouts STAGE CIRCUIT CONGESTION Description No free stage circuits are available between SSW and GSW. Possibility to change the default effect Not possible.102 60EH .101 60DH . Possibility to change the default effect Not possible. Alarms No alarms. The originating exchange connects a special information tone to the subscriber. Most of the unit restarts are recorded with clear codes set on the time-outs of the call control time supervision. 5. The originating exchange connects a special information tone to the subscriber.SUBSCRIBER MODULE OR V5 INTERFACE FAILURE. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms. Clear request has been received from the access node. Possibility to change the default effect Not possible. Alarms No alarms.104 700H . 82 Id:0900d80580635beb DN078927 Issue 1-0 . 5. The originating exchange connects a congestion tone to the subscriber. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible.LONG AON REQUEST Text in MML printouts LONG AON REQUEST Description Line signal AON REQUEST or OVERLONG ANSWER (8.Clear codes DX200 Clear Code List Text in MML printouts MOD OR V5 FAIL CALL CLEAR Description A plug-in unit has broken down.or 0-traffic). Detected by Program block SI2PRB SI6PRB Explanation – – Default effect on the exchange The call is cleared in terminal and transit exchanges. or it has been removed from subscriber module SUBE. or the fault diagnosis has executed a forced test. Alarms No alarms. SI2PRB sets this clear code if bearer channel is faulty due to access node internal failure. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. or end-of-selection analysis) fails. dialling preanalysis. OUREGI. Possibility to change the default effect Not possible. facility. facility.g. INREGI. origin. LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e. ICxPRB. INREGI. INREGI. origin. The originating exchange connects a congestion tone to the subscriber. origin. operator. origin. INREGI. or end-of-selection analysis) fails. operator.g. OC6PRB. facility. ICxPRB. dialling preanalysis. DN078927 Issue 1-0 Id:0900d80580635beb 83 . ICxPRB. origin. OC6PRB. release.g. operator. dialling preanalysis. operator. OC6PRB. OUREGI. INREGI LHSPRB OC6PRB OUREGI TPSPRB Default effect on the exchange The call is cleared in terminal and transit exchanges. release. or end-of-selection analysis) fails. ICxPRB.g. OC6PRB. Alarms No alarms.g.105 701H . LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e. ICxPRB. release. origin. release. INREGI. facility. or end-of-selection analysis) fails. OUREGI. dialling preanalysis. facility. OUREGI. LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e. dialling preanalysis. or end-of-selection analysis) fails. operator. or because the analysis routine has returned an incorrect parameter. LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. operator. OC6PRB. OC6PRB. Detected by Program block ICXPRB Explanation ICxPRB. OUREGI. LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e. INREGI. facility. or end-of-selection analysis) fails. release. release. LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.REGISTER ANALYSIS FAILED Text in MML printouts REGISTER ANALYSIS FAILED Description The register analysis has failed either due to unknown addressing in the analysis file. OUREGI. dialling preanalysis.DX200 Clear Code List Clear codes 5. 5. INREGI or OUREGI sets the clear code when the resource (outgoing circuit. INREGI or OUREGI sets the clear code when the resource (outgoing circuit. 84 Id:0900d80580635beb DN078927 Issue 1-0 . INREGI or OUREGI sets the clear code when the resource (outgoing circuit. MFC or PBRU device) is not available within the queuing time limit. IC6PRB. SI6PRB. MFC or PBRU device) is not available within the queuing time limit. Detected by Program block IC6PRB Explanation IC6PRB. Possibility to change the default effect Not possible. INREGI or OUREGI sets the clear code when the resource (outgoing circuit.PARITY ERROR FROM PBRU/MFCU DEVICE Text in MML printouts PARITY ERR FROM PBRU/MFCU Description There has been an error in interpreting a multifrequency character. The originating exchange connects a congestion tone to the subscriber.QUEUEING TIME EXCEEDED Text in MML printouts QUEUEING TIME EXCEEDED Description The queuing for resources has failed because the maximum queuing time has been exceeded. SI6PRB. MFC or PBRU device) is not available within the queuing time limit. IC6PRB. Alarms No alarms.107 704H .Clear codes DX200 Clear Code List 5. MFC or PBRU device) is not available within the queuing time limit. SI6PRB. INREGI OUREGI SI6PRB Default effect on the exchange The call is cleared in terminal and transit exchanges. IC6PRB.106 702H . SI6PRB. 5.MODULE OR V5 INTERFACE NOT AVAILABLE Text in MML printouts MOD OR V5 NOT AVAILABLE Description The subscriber module's or V5 interface's WO-EX state has been changed. Alarms No alarms. Default effect on the exchange The call is cleared in terminal and transit exchanges. SI6PRB sets the clear code when the subscriber module's or V5 interface's state is not WO-EX. Alarms No alarms. or the message connection to the module or V5 interface has broken. INREGI or OUREGI sets the clear code when ACSERV sends the parity_err_from_pbru_mfcu or aux_mfc_parity_err message. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible.1 interface congestion or bearer channel reservation fails. DN078927 Issue 1-0 Id:0900d80580635beb 85 . The originating exchange connects a congestion tone to the subscriber. Detected by Program block SI2PRB SI6PRB Explanation SI2PRB sets this clear code if pcm is not available in the V5. Default effect on the exchange The call is cleared in terminal and transit exchanges. – SI6PRB. Possibility to change the default effect Not possible. INREGI or OUREGI sets the clear code when ACSERV sends the parity_err_from_pbru_mfcu or aux_mfc_parity_err message.108 705H .DX200 Clear Code List Clear codes Detected by Program block INREGI OUREGI SI6PRB Explanation SI6PRB. Possibility to change the default effect Not possible.109 706H . Possibility to change the default effect Not possible. 5. Default effect on the exchange The call is cleared in terminal and transit exchanges. so the calls controlled by them will be cleared. SUB-C. The originating exchange connects a congestion tone to the subscriber. Alarms No alarms.110 707H . Alarms No alarms. 86 Id:0900d80580635beb DN078927 Issue 1-0 . Detected by Program block SI6PRB Explanation SI6PRB sets the clear code when the state of the subscriber module is WO-RE and the old state is WO-EX. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.CALL INTERRUPTED DURING REGISTER ANALYSIS Text in MML printouts CALL INTER REG ANALYSIS Description The internal analysis of the call control has failed.SUBSCRIBER MODULE RESTARTED Text in MML printouts SUBSCRIBER MODULE ºRESTART Description The SSP program or the SUB. or SUB-D have been restarted. The originating exchange connects a congestion tone to the subscriber.Clear codes DX200 Clear Code List 5. 111 70AH . CAC.112 70BH . Default effect on the exchange The exhange clears the call. Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 87 .DX200 Clear Code List Clear codes 5.MODEM ERROR Text in MML printouts MODEM ERROR Description The modem DSP (Digital Signal Processing) software does not support the modem type detected. Possibility to change the default effect Not possible. The clear code is also used with PCM breaks. This clear code is used if the release request of the call has been received from a refresher program block. A special tone is connected. and LSU switchovers. This clear code is set also if the modem DSP software does not detect a carrier signal or the carrier signal is lost during the call. restarts of the LSP preprocessor. or LSU. 5. Detected by Program block MGAPRB Explanation MGAPRB sets the clear code according to an error type obtained from MRMPRB. Possibility to change the default effect Not possible. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.FORCED CLEAR OF A CALL Text in MML printouts FORCED CLEAR OF A CALL Description The call has been cleared due to the restart of CCSU. The originating exchange connects a congestion tone to the subscriber. 5. 88 Id:0900d80580635beb DN078927 Issue 1-0 . Alarms No alarms. incorrect announcement creation data. The originating exchange connects a congestion tone to the subscriber. The originating exchange connects a congestion tone to the subscriber. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms.OVERLOAD CONTROL SYSTEM ERROR Text in MML printouts OVERLOAD CONTROL SYS ERRO Description An internal failure in the overload control system. for example). Possibility to change the default effect Not possible.g. Possibility to change the default effect Not possible. which controls the amount of calls simultaneously accepted in the system. The reason may be e. The announcement service examines the problem (and sets a suitable alarm.113 70CH . Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.ANNOUNCEMENT SERVICE FAILURE Text in MML printouts ANNOUNCEMENT ERROR Description Use of the announcement service has failed. 5.114 70DH . capacity overflow.Clear codes DX200 Clear Code List Alarms No alarms. or hardware error. Using facility routing. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Default effect on the exchange The call is cleared in terminal and transit exchanges.115 70EH .DX200 Clear Code List Clear codes 5. Possibility to change the default effect Using facility routing (command group RE. Alarms 2225 DN078927 Issue 1-0 Id:0900d80580635beb 89 . Possibility to change the default effect Not possible. parameter CDP). Alarms No alarms. The originating exchange connects a congestion tone to the subscriber. the call can be directed for reanalysis in tree 2CH both in terminal and transit exchanges. Detected by Program block ICXPRB Explanation The ICXPRB sets this clear code.CONFIGURATION ERROR Text in MML printouts CONFIGURATION ERROR Description Configuration error in the exchange. 5.116 710H .NO ANALYSIS FOR CARRIER ACCESS CODE Text in MML printouts NO ANA FOR OPER IDENTIF Description No digit analysis created for the carrier access code. the originating exchange can connect an audible tone to the subscriber. Detected by Program block IC1PRB IC3PRB Explanation IC1PRB. Detected by Program block IC1PRB IC3PRB IC6PRB Explanation C1PRB. C1PRB.117 711H . IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in transit exchange.TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE Text in MML printouts TRAN EX NOT ACCEPT TARIFF Description Tariff is not accepted in transit exchange. IC1PRB.Clear codes DX200 Clear Code List 5. IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in transit exchange.TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE Text in MML printouts ORIG EXCH NOT ACCPT TARIFF Description Tariff is not accepted in originating or interworking exchange.118 712H . Default effect on the exchange Call is disconnected. Possibility to change the default effect Not possible. IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in transit exchange. C1PRB. 90 Id:0900d80580635beb DN078927 Issue 1-0 . IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in originating or interworking exchange. Alarms 2300 5. IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in originating or interworking exchange. Default effect on the exchange The call is cleared in terminal and transit exchanges.NO ISUP ROUTE Text in MML printouts NO ISUP ROUTE Description There is no ISUP route in the exchange that would meet the signalling requirements. Alarms No alarms.120 714H . DN078927 Issue 1-0 Id:0900d80580635beb 91 . Possibility to change the default effect Call continueing may be changed by EOS analysis management -MML. IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in originating or interworking exchange. Default effect on the exchange Call is disconnected. Alarms 2300 5.119 713H .DX200 Clear Code List Clear codes Program block IC6PRB Explanation IC1PRB.ATTRIBUTE DIRECTED ROUTING MISMATCH Text in MML printouts ATTRIB GENERAL MISMATCH Description The route selection ended in congestion based on the attribute directed routing feature. The originating exchange connects a congestion tone to the subscriber. because there is no ISUP route in the exchange that would meet the signalling requirements. Possibility to change the default effect Not possible. 5. Detected by Program block CMANAL Explanation CMANAL sets the clear code. 92 Id:0900d80580635beb DN078927 Issue 1-0 . RK and RM. The commands of the command group RR can also be used to modify the supplementary services defined for the route. can set the required supplementary services as 'preferred'. Depending on the call.Clear codes DX200 Clear Code List Detected by Program block CMANAL Explanation The CMANAL returns this clear code when requested by the ICxPRB. Default effect on the exchange The call is cleared. but the call must be cleared. but this has to be done in the original call attempt.121 715H . if the required supplementary service(s) were not found. 5. UUS1 or CCBS). Alarms No alarms. certain characteristics can be required from the outgoing route. Detected by Program block CMANAL Explanation The CMANAL returns this clear code when requested by the ICxPRB. ICxPRB. Default effect on the exchange Routing cannot be continued with the present requirements. Possibility to change the default effect The call control process. if the digit analysis ended in congestion. including the ability to support supplementary services needed in the call (like CUG. Alarms No alarms. which means that the supplementary services are not obligatory. Possibility to change the default effect The parameters of the destination and subdestination can be redefined with the commands of the command groups RD.REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE Text in MML printouts FACIL NOT AVAIL ON ROUTE Description The available routes do not support the required supplementary service(s). a subdestination has been blocked.DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION Text in MML printouts CM ANALYSIS CONGESTION Description The digit analysis has resulted in a congestion due to a restriction found in the analysis: the destination has been blocked. Detected by Program block CMANAL Explanation The CMANAL returns this clear code when requested by the ICxPRB.DX200 Clear Code List Clear codes 5. This clear code is used also when a call has been cleared because the maximum amount of satellites per one call has exceeded. or a combination of the aforementioned. This clear DN078927 Issue 1-0 Id:0900d80580635beb 93 . 5. ICxPRB.REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE Text in MML printouts BEARER CAP NOT RECEIVED Description The call cannot be routed to available routes. the use of the subdestination has been restricted. Releasing a call due to these causes is usually a desired consequence. overflow from the subdestination has been restricted. which is used if the primary bearer capability could not be provided. as the route did not have the required bearer capability. an unrestricted digital route. Possibility to change the default effect The call control process. RK and RM. but the available routes only offer speech transfer. Default effect on the exchange Routing cannot be continued with the present requirements. can set a secondary bearer capability requirement. if the required bearer capability was not found.123 718H . but this has to be done in the original call attempt. The call can require e. an alternative subdestination has been bypassed. This can be modified with the commands of the command groups RD. Alarms No alarms.122 716H . but the call must be cleared. This means that the call must be cleared as the required service cannot be provided. a subdestination has been bypassed.g. The operator can also modify the bearer capability with the commands of the command group RR. NO RESOURCE AVAILABLE FOR CALL Text in MML printouts NO RESOURCE FOR CALL Description The clear code is set when there is no resource for call. DPNPRB. Detected by Program block CMANAL Explanation The CMANAL returns this clear code when requested by the ICxPRB. but the call must be cleared.IPOPRB set the clear code when there is no resource for the call.PRKPRB.RMAPRB. PROHIBITED DIALLING (0C01H) or ATTRIBUTE GENERAL MISMATCH (0714H). Default effect on the exchange Routing cannot be continued as the situation is irreversible.ICXPRB.CFOPRB. hand reservation fails.g. Detected by Program block CFOPRB Explanation SIXPRB. Alarms No alarms.g.g.OCXPRB. 5.RMAPRB. if the digit analysis ended in congestion. Possibility to change the default effect The parameters of the destination and subdestination can be redefined with the commands of the command groups RD. when the clear code is FILE ERROR (0509H). e.OCXPRB. used when the cause of the congestion can be expressed with the clear codes BEARER CAP NOT RECEIVED (0716H).ICXPRB. e. DPNPRB ICXPRB IDOPRB OCXPRB PRKPRB RMAPRB SIXPRB 94 Id:0900d80580635beb DN078927 Issue 1-0 . FACIL NOT AVAIL ON ROUTE (0715H).CFOPRB.PRKPRB.Clear codes DX200 Clear Code List code is not.124 719H . – – – – – – SIXPRB. e. RK and RM.DPNPRB. hand reservation fails in the call setup phase. however.IPOPRB set the clear code when there is no resource for the call. or in analysis error situations. hand reservation fails in the call setup phase. IC1PRB and IC3PRB starts alternative routing.REQUESTED CHANNEL NOT AVAILABLE Text in MML printouts REQ CHANNEL NOT AVAILABLE Description A PBX has requested a channel which is not available. Alarms 2668 5. It can be for example busy or not in use. Possibility to change the default effect Not possible. Possibility to change the default effect Not possible. 5. DN078927 Issue 1-0 Id:0900d80580635beb 95 . Default effect on the exchange The call from an access is not accepted. Alarms No alarms. Detected by Program block SI1PRB Explanation Detected by SI1PRB when the requested channel is not created.DX200 Clear Code List Clear codes Default effect on the exchange IC6PRB.IDENTIFIED CHANNEL NOT EXIST Text in MML printouts IDENTIFIED CH NOT EXIST Description A PBX has requested a channel which is not created.125 71AH .126 71BH . Default effect on the exchange A call from an access is not accepted. Possibility to change the default effect Not possible. not in use). Detected by Program block MGAPRB Explanation MGAPRB sets the clear code according to the error type obtained from MRMPRB. 5. Alarms No alarms. Default effect on the exchange The exhange starts hunting for a new free circuit from the route. 5. Alarms No alarms.Clear codes DX200 Clear Code List Detected by Program block SI1PRB Explanation Detected by SI1PRB when the requested channel is not available (busy.POINT-TO-POINT PROTOCOL ERROR Text in MML printouts PPP ERROR 96 Id:0900d80580635beb DN078927 Issue 1-0 .PACKET CONTROL UNIT CONGESTION Text in MML printouts PCU CONGESTION Description No DSP (Digital Signal Processing) or ISDN resource available for the call in the PCU (Packet Control Unit) plug-in unit.128 71DH . Possibility to change the default effect Not possible.127 71CH . 5. The originating exchange connects a congestion tone to the subscriber. The original called subscriber's number received from the trunk circuit has been too long.130 802H .LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED Text in MML printouts ORIG. Default effect on the exchange The exhange clears the call.DX200 Clear Code List Clear codes Description Point-to-Point (PPP) Protocol has not been started or a failure in PPP-protocol has occured. Alarms No alarms. Possibility to change the default effect Not possible.B-NO LENGTH EXCEEDED Description The original called subscriber's (B subscriber's) number is too long. 5.LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED DN078927 Issue 1-0 Id:0900d80580635beb 97 . Alarms No alarms. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. Detected by Program block MGAPRB Explanation MGAPRB sets the clear code according to the error information obtained from the Point-to-Point Protocol program block.129 801H . A special tone is connected. 5.Clear codes DX200 Clear Code List Text in MML printouts A-NUMBER LENGTH EXCEEDED Description The calling subscriber's (A subscriber's) number is too long. The originating exchange connects a congestion tone to the subscriber.INVALID CALLING SUBSCRIBER CATEGORY Text in MML printouts INVALID SUBSCR. Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal and transit exchanges. 98 Id:0900d80580635beb DN078927 Issue 1-0 . The originating exchange carries out a digit re-analysis in tree 32H. – Default effect on the exchange The call is cleared in terminal and transit exchanges. The original calling subscriber's number received from the trunk circuit has been too long. Detected by Program block INREGI Explanation INREGI sets the clear code when a too long A-subscriber number is received from R2 signalling.131 803H . Detected by Program block INREGI OUREGI Explanation INREGI or OUREGI sets the clear code when the subscriber category received from R2 signalling cannot be identified. A CATEGO Description The category data of the calling subscriber (A-subscriber) received from the incoming circuit is invalid. Alarms No alarms. 133 806H . transit and terminal exchanges can carry out a digit re-analysis in tree 32H or connect an audible tone. Alarms No alarms. parameter CFC). parameter CCF). Detected by Program block ICXPRB Explanation INREGI or ICxPRB sets the clear code when the outgoing circuit group is in BARRED state or all outgoing circuits are reserved on the used route. Interception tree 2DH (command group RE.132 804H .DX200 Clear Code List Clear codes Possibility to change the default effect Using facility routing (command group RE.2 interface if circuit reservation fails.OUTGOING CIRCUIT CONGESTION Text in MML printouts OUTGOING CIRCUIT CONGEST Description All circuits of the hunted external route are busy. – – INREGI SI2PRB Default effect on the exchange The call is cleared in terminal and transit exchanges. the originating exchange can connect an audible tone to the subscriber. 5. SI2PRB sets this clear code in the V5. Using facility routing. Possibility to change the default effect By using facility routing.IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE Text in MML printouts A IDENTITY NOT AVAILABLE DN078927 Issue 1-0 Id:0900d80580635beb 99 . 5. The originating exchange carries out a digit re-analysis in interception tree. Alarms No alarms. terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. The originating exchange connects a congestion tone to the subscriber. 100 Id:0900d80580635beb DN078927 Issue 1-0 . Alarms No alarms. Possibility to change the default effect Not possible.134 809H . The termination of the call set-up phase requires the identity of the Asubscriber. Possibility to change the default effect Not possible. 5. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.Clear codes DX200 Clear Code List Description The identity of the calling subscriber (A-subscriber) has not been received from the incoming circuit.ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT Text in MML printouts MFC ERROR SIGN FROM OUT Description The MFC signal received from the outgoing circuit does not comply with the signals in use in the signalling system. Alarms No alarms. Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block OUREGI Explanation OUREGI sets the clear code when a faulty MFC signal has been received from the outgoing connection. The originating exchange connects a congestion tone to the subscriber. Detected by Program block INREGI Explanation INREGI sets the clear code when a faulty MFC signal has been received from the incoming circuit. Possibility to change the default effect Not possible. Detected by Program block OUREGI Explanation OUREGI sets the clear code when it has no selection available with which to start outgoing signalling.NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT Text in MML printouts NO B-NUMB TO SEND TO OG Description An attempt has been made to start signalling without sending it any digit to be analysed.135 80AH . The originating exchange connects a congestion tone to the subscriber. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. 5. DN078927 Issue 1-0 Id:0900d80580635beb 101 . Default effect on the exchange The call is cleared in terminal and transit exchanges.DX200 Clear Code List Clear codes 5.136 80BH .ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT Text in MML printouts MFC ERROR SIGN FROM INCOM Description The MFC signal received from the incoming circuit does not comply with the signals in use in the signalling system. Alarms No alarms. 138 80DH .UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT Text in MML printouts UNKNOWN DECADIC SIGNAL Description An unknown overdecadic signal has been received from the incoming circuit.OUTGOING CIRCUIT OUT OF ORDER Text in MML printouts OUT CIRCUIT OUT OF ORDER Description The state data on the outgoing circuit is contradictory to the marker switching data. Reasons for contradiction: Because of a PCM disturbance.Clear codes DX200 Clear Code List Possibility to change the default effect Not possible. the outgoing circuit is in fault filtering state but has not yet been barred from hunting. consequently the seizure is rejected. Detected by Program block INREGI Explanation INREGI sets the clear code when an undefined decadic signal has been received from the incoming circuit. Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. 5. The circuit had already been hunted before the PCM disturbance. 5. Alarms No alarms. Alarms No alarms. Signalling of the circuit is not in idle state and the circuit has been hunted before barring. The originating exchange connects a congestion tone the subscriber. Detected by - 102 Id:0900d80580635beb DN078927 Issue 1-0 .137 80CH . Possibility to change the default effect Not possible. Alarms No alarms. Interception tree 2EH. Possibility to change the default effect Not possible. Alarms No alarms. parameter CFC). Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. 5.139 80EH . If an unknown line signal is received during the conversation phase.INCOMING CIRCUIT OUT OF ORDER Text in MML printouts IN CIRCUIT OUT OF ORDER Description An unknown line signal has been received from the incoming circuit.140 80FH . The originating exchange carries out a digit re-analysis in interception tree. and a call in the set-up phase is interrupted. Interception tree 2DH (command group RE. Detected by - DN078927 Issue 1-0 Id:0900d80580635beb 103 . Interception tree 2EH. the connection is cleared.DX200 Clear Code List Clear codes Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. The originating exchange carries out a digit re-analysis in interception tree.CIRCUIT CONGESTION Text in MML printouts CIRCUIT CONGESTION Description Congestion or another equivalent signal or message has been received from the outgoing circuit during the call set-up phase. Using facility routing. 5.NETWORK FAILURE Text in MML printouts NETWORK FAILURE Description A network element cannot perform an operation because of the failure of another network element. The originating exchange carries out a digit re-analysis in an interception tree.FACILITY NOT SUPPORTED Text in MML printouts FACILITY NOT SUPPORT Description The requested service is not supported in the public network. Interception tree 32H (command group RE. Interception tree 2DH (command group RE. In the originating exchange a congestion tone is connected to the subscriber. Alarms No alarms. Possibility to change the default effect Using facility routing. Alarms No alarms. parameter CCF). 5. terminal and transit exchanges can carry out a digit re-analysis in an interception tree or connect an audible tone. Detected by - 104 Id:0900d80580635beb DN078927 Issue 1-0 .Clear codes DX200 Clear Code List Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. the originating exchange can connect an audible tone to the subscriber.141 810H .142 811H . Detected by Default effect on the exchange In the transit and terminal exchanges the call is cleared. parameter CFC). Possibility to change the default effect Using facility routing (command group RE. The originating exchange carries out a digit re-analysis in tree 2DH (command group RE. Alarms No alarms. Using facility routing. originating exchange detected that congestion was caused by hunting for exchange device. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms. Possibility to change the default effect Using facility routing. the originating exchange can carry out a digit re-analysis in tree 31H. congestion on the circuit group. The originating exchange connects a congestion tone to the subscriber. 5. the originating exchange can connect an audible tone to the subscriber.DX200 Clear Code List Clear codes Default effect on the exchange The call is cleared in terminal and transit exchanges.SWITCHING EQUIPMENT CONGESTION Text in MML printouts SWITCHING EQUI CONGESTION Description A call clear received from the network.CIRCUIT GROUP CONGESTION Text in MML printouts CIRCUIT GROUP CONGESTION Description Call clear received from the network.144 814H . 5. Detected by - DN078927 Issue 1-0 Id:0900d80580635beb 105 .143 813H . Using facility routing. parameter CFC). terminal and transit exchanges can carry out a digit re-analysis in tree 2DH or connect an audible tone. parameter CSC). terminal and transit exchanges can carry out a digit re-analysis in tree 31H or connect an audible tone. Using facility routing. the originating exchange can connect an audible tone to the subscriber. Using facility routing. the originating exchange can connect an audible tone to the subscriber.ACCESS BARRED TO THE CALLED SUBSCRIBER Text in MML printouts B ACCESS BARRED Description An access barred message has been received which indicates that the call could not be connected to the subscriber line indicated by the received number. The originating exchange carries out a digit re-analysis in tree 35H. Alarms No alarms. Interception tree 2EH (command group RE. parameter CRO). terminal and transit exchanges can carry out a digit re-analysis in tree 35H or connect an audible tone. SEND SPECIAL INFORMATION TONE Text in MML printouts CALL UNSUC SEND INFO TONE 106 Id:0900d80580635beb DN078927 Issue 1-0 . 5. Possibility to change the default effect Using facility routing (command group RE. or subscriber facility "incoming call barring" has been activated.145 815H . parameter CFC).CALL FAILED. Alarms No alarms. Possibility to change the default effect Using facility routing terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. The originating exchange carries out a digit re-analysis in interception tree. This may occur if the called connection belongs to a closed user group.146 816H . Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. parameter CAB). Interception tree 2DH (command group RE. 5.Clear codes DX200 Clear Code List Default effect on the exchange The call is cleared in terminal and transit exchanges. terminal and transit exchanges can carry out a digit re-analysis in tree 2AH or connect an audible tone. the originating exchange can connect an audible tone to the subscriber. the originating exchange can connect an audible tone to the subscriber. Using facility routing. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Using facility routing (command group RE. The originating exchange carries out a digit re-analysis in tree 34H. The originating exchange carries out a digit re-analysis in tree 2AH. UNALLOCATED NUMBER Text in MML printouts N-UNALLOCATED NUMBER Description Information "unallocated number" has been received from the network.NETWORK. Alarms No alarms. 5. Using facility routing. LINE OUT OF SERVICE Text in MML printouts N-LINE OUT OF SERVICE DN078927 Issue 1-0 Id:0900d80580635beb 107 . 5.DX200 Clear Code List Clear codes Description Information "send special information tone" has been received from the network. Alarms No alarms.NETWORK. Possibility to change the default effect Using facility routing (command group RE. parameter CST). Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.147 817H .148 818H . parameter CUN). the call can be directed for reanalysis in tree 34H both in terminal and transit exchanges. Possibility to change the default effect Using facility routing (command group RE. SUBSCRIBER NUMBER CHANGED Text in MML printouts N-SUBSCRIB NUMBER CHANGED Description Information "subscriber number changed" has been received from the network. Using facility routing. Interception tree 2FH (command group RE. Possibility to change the default effect Using facility routing the terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Alarms No alarms. SI6PRB – Default effect on the exchange The call is cleared in terminal and transit exchanges. parameter CSN). the call can be directed for reanalysis in tree 29H both in terminal and transit exchanges. SI2PRB sets this clear code: in V5 interface congestion if state or user port is not available or bearer channel reservation fails. Alarms No alarms. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. the originating exchange can connect an audible tone to the subscriber. 5. The originating exchange carries out a digit re-analysis in interception tree. The originating exchange does reanalysis in the interception tree.Clear codes DX200 Clear Code List Description Information "line out of service or unallocated" has been received from the network.149 819H . Detected by Program block SI2PRB SI6PRB Explanation SI2PRB. parameter CFB). 108 Id:0900d80580635beb DN078927 Issue 1-0 .NETWORK. CONGESTION IN TERMINAL EXCHANGE Text in MML printouts TERMINAL CONGESTION Description Congestion has been detected in the terminal exchange.DX200 Clear Code List Clear codes 5. for example. Rerouting the call is not possible. Possibility to change the default effect Not possible. The originating exchange connects a congestion tone to the subscriber. DN078927 Issue 1-0 Id:0900d80580635beb 109 . Detected by Program block ICXPRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges.151 81DH . that hunting a circuit for a mobile terminating call has failed. Alarms No alarms. The reason can be.150 81AH . Alarms No alarms. 5. Detected by Default effect on the exchange – Possibility to change the default effect Not possible.CONGESTION IN INTERNATIONAL CALL Text in MML printouts INTERNATIONAL CONGESTION Description The TUP's International Congestion message has been received from the network. 5. OVERLOAD CONGESTION Text in MML printouts NETWORK OVERLOAD Description An overload message has been received from the network. The originating exchange connects a special information tone to the subscriber. the call is cleared with this clear code. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms. Detected by Program block SI4PRB Explanation The SI4PRB or the SI7PRB sets this clear code when it has received an overload/OLM message from the network after an IAM/IFAM has been sent.153 81FH . This signalling is in use in Italy The DTE-controlled not_ready cause code received from the NUP signalling. The function to the network depends on the signalling used. 110 Id:0900d80580635beb DN078927 Issue 1-0 .CONTROLLED NOT READY Text in MML printouts CONTROLLED NOT READY Description The CONTROLLED NOT READY message of inter-exchange TUP signalling has been received from the network.NETWORK. Possibility to change the default effect Not possible. If it is not possible. Possibility to change the default effect Not possible. – SI7PRB Default effect on the exchange The call is rerouted to an alternative route.Clear codes DX200 Clear Code List 5.152 81EH . INVALID TRANSIT NETWORK SELECTION Text in MML printouts INVALID TRANSIT NETWORK Description The chosen transit network is erroneous or it does not exist. Alarms No alarms.155 821H . – Default effect on the exchange The call is cleared in terminal and transit exchanges.NETWORK MESSAGE CONTENT ERROR Text in MML printouts NETWORK MSG CONTENT ERROR Description Inconsistent network message received. Detected by Program block SI4PRB SI7PRB Explanation SI4PRB or SI7PRB sets this clear code when it has noticed an inconsistent network message. 5. 5.DX200 Clear Code List Clear codes Alarms No alarms.154 820H . The originating exchange connects a congestion tone to the subscriber. Detected by Program block SI7PRB Explanation – Default effect on the exchange – DN078927 Issue 1-0 Id:0900d80580635beb 111 . Possibility to change the default effect Not possible. An alarm has also been set to indicate call clearing. Alarms No alarms.RECOVERY ON TIMER EXPIRY Text in MML printouts RECOVERY ON TIMER EXPIRY Description Recovery from fault situation has been initiated within network according to ISUP (Q. 5.157 824H . Alarms No alarms.767) Detected by Program block SI7PRB Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges.Clear codes DX200 Clear Code List Possibility to change the default effect Not possible.PCM FAULTY Text in MML printouts PCM FAULTY Description This code is set when the system has found that PCM is faulty and has asked the signalling to clear the call. a transmission link failure etc.156 822H . The originating exchange connects a busy tone to the subscriber. 5. Possibility to change the default effect Not possible. The reason may be an internal or external failure: an ET failure. Detected by Program block SI2PRB Explanation – 112 Id:0900d80580635beb DN078927 Issue 1-0 . DN078927 Issue 1-0 Id:0900d80580635beb 113 . Detected by Program block SI5PRB Explanation The SI5PRB sets this clear code when it receives the NNC message from the network.CONGESTION FROM NATIONAL NETWORK Text in MML printouts N NATIONAL CONGESTION Description The National Network Congestion message (ITUP) has been received from the network. the terminal and transit exchanges can carry out a digit re-analysis in the interception tree 32H (command group RE. 2909.DX200 Clear Code List Clear codes Program block SI3PRB SI4PRB SI5PRB SI7PRB SI8PRB Explanation – – – – – Default effect on the exchange The call from an access is not accepted. Alarms 2202. 2910. 2902. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in the terminal and transit exchanges.158 828H . parameter CCF). 2915 5. Alarms No alarms. 2900. 2204. The originating exchange connects an announcement or an audible tone to the subscriber. 2912. Possibility to change the default effect Using facility routing. 160 830H . IC3PRB or IC6PRB. Possibility to change the default effect By using facility routing. 5. Alarms No alarms. the terminal and transit exchanges can carry out a digit reanalysis in an interception tree or connect an audible tone. RMAPRB returns this clear code to IC1PRB.Clear codes DX200 Clear Code List 5. 114 Id:0900d80580635beb DN078927 Issue 1-0 . parameter CFC). Detected by Program block IC1PRB IC3PRB IC6PRB Q50PRB RMAPRB Explanation Q50PRB sets this clear code when RMAPRB has requested DCME.NUMBER PORTABILITY Text in MML printouts PORTED NUMBER NETWORK Description The routing number of the subscriber has changed because the subscriber has moved to the network of another operator. – – – – Default effect on the exchange The call is cleared in terminal and transit exchanges. Interception tree 2DH (command group RE.DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION Text in MML printouts DCME CONGESTION Description This clear code is set when the call terminates to outgoing call congestion which is caused by the missing traffic transfer capacity in a DCME and no other alternative route is available. The originating exchange carries out a digit re-analysis in interception tree.159 829H . Using facility routing the originating exchange can connect an audible tone to the subscriber. which is decreased in every intermediate exchange.ROUTING ERROR Text in MML printouts ROUTING ERROR Description Error in routing. Default effect on the exchange The call is released. Alarms 1206 DN078927 Issue 1-0 Id:0900d80580635beb 115 . Using EOS -analysis handling ( MML command group RX ) the analysis tree can be changed. 5.161 832H . Alarms No alarms. The originating exchange carries out a digit re-analysis in interception tree 32H. Detected by Program block SI7PRB Explanation SI7PRB sets this release code.DX200 Clear Code List Clear codes Detected by Program block INXPRB SI1PRB SI7PRB Explanation SI7PRB SI1PRB INXPRB – – Default effect on the exchange The call is cleared in terminal and transit exchanges. parameter CCF ) or connect an audible tone to the subscriber. When it becomes zero. The hop counter helps to prevent looping between networks in the multicarrier environment. Possibility to change the default effect Not possible. Possibility to change the default effect Using facility routing terminal and transit exchanges can carry out a digit re-analysis in the interception tree 32H ( command group RE. the call is cleared and an alarm is given. after getting #25 cause code. The hop counter has an initial (maximal) value. The hop counter has exhausted in the network. Clear codes DX200 Clear Code List 5.162 833H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE Text in MML printouts DCME FAILURE Description DX200 has received a line signal Out-of-service from DCME. A call on that circuit is cleared. Q50PRB informs SS-program block involved about this with a message dcme_fail_release_s. Detected by Program block Q50PRB SI5PRB SI7PRB Explanation SI5PRB, SI7PRB – – Default effect on the exchange The call is cleared. An announcement or a tone is connected to the subscriber. Possibility to change the default effect Using facility routing, terminal and transit exchanges can carry out a digit re-analysis or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2DH (command group RE, parameter CFC). Alarms 2997 5.163 851H - TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNALLING Text in MML printouts SCC CONGESTION Description The exchange selects calls randomly according to the current clearing level, and requests signalling to clear the selected calls. There can be national (0-3) or international (0-5) clearing levels, for which the user can define a clearing percentage (the greater the level the higher the percentage). The Signalling Congestion Control system (SCC) restricts traffic to the destination point because of congestion on the signalling link, or because the partner end has requested traffic restriction with a TFC message. 116 Id:0900d80580635beb DN078927 Issue 1-0 DX200 Clear Code List Clear codes Detected by Program block SI7PRB Explanation – Default effect on the exchange This causes clearing of call, and no repeat attempts are allowed. Possibility to change the default effect Not possible. Alarms No alarms. 5.164 900H - NO MF FORWARD SIGNAL Text in MML printouts NO MF FORWARD SIGNAL Description In multifrequency signalling, no MF forward signal has been received from the incoming circuit during the time supervision T1 = 350 ms. The MF signal 15 is sent to the incoming circuit. Detected by Program block INREGI Explanation INREGI sets the clear code when ACSERV sends message aux_no_forward_char (6539). Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.165 901H - TOO LONG MF FORWARD SIGNAL Text in MML printouts TOO LONG MF FORWARD SIGNL DN078927 Issue 1-0 Id:0900d80580635beb 117 Clear codes DX200 Clear Code List Description In multifrequency signalling, an MF signal with a duration of >= 1 - 2 s has been received from the incoming circuit. Detected by Program block INREGI Explanation INREGI sets the clear code when ACSERV sends message aux_long_char_s (6540). Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.166 905H - TOO LONG MF BACKWARD SIGNAL Text in MML printouts TOO LONG MF BACKWARD SIGN Description In multifrequency signalling, an MF signal with a duration of >= 3 - 4 s has been received from the outgoing circuit. Detected by Program block OUREGI Explanation OUREGI sets the clear code when CASSIG sends message long_char_s (0081). Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 118 Id:0900d80580635beb DN078927 Issue 1-0 DX200 Clear Code List Clear codes 5. Alarms No alarms. The originating exchange connects a special information tone to the subscriber.167 90CH .PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT Text in MML printouts PREMAT SEIZ ACK OUT CRCT Description Acknowledgement to a seizure sent on an outgoing circuit has been received before the expiration of the safety time specified for the signalling. 5. Detected by Program block CASSIG Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges.PREMATURE ANSWER Text in MML printouts PREMATURE ANSWER Description CASSIG-B has received an answer signal from the outgoing circuit during the register phase. The originating exchange connects a special information tone to the subscriber. DN078927 Issue 1-0 Id:0900d80580635beb 119 . Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. Detected by Program block OUREGI Explanation OUREGI sets the clear code when CASSIG sends message premature_answer_s. The register has not yet received the B-subscriber's (called subscriber) state data from the outgoing circuit.168 90EH . Possibility to change the default effect Not possible. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.Clear codes DX200 Clear Code List Possibility to change the default effect Not possible.170 A01H . Alarms No alarms. Alarms No alarms. The originating exchange connects a special information tone to the subscriber.169 90FH . The originating exchange connects a special information tone to the subscriber.ANSWER AFTER B BUSY Text in MML printouts ANSWER AFTER B BUSY Description An answer has been received from the outgoing circuit after the called subscriber busy information. Possibility to change the default effect Not possible. 120 Id:0900d80580635beb DN078927 Issue 1-0 . 5.CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) Text in MML printouts IDLE CONTROL END MISSED Description No seizing acknowledged signal has been received from the outgoing circuit within 400 ms from the sending of the seizure. 5. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. the originating exchange can connect an audible tone to the subscriber.171 A02H . Possibility to change the default effect Not possible. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H. the transit and terminal exchanges can connect an audible tone to the incoming circuit or carry out a digit reanalysis in tree 34H. DN078927 Issue 1-0 Id:0900d80580635beb 121 . Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. 5.INVALID MESSAGE FROM TRUNK CIRCUIT Text in MML printouts INVALID TRUNK CRCT MSG Description An invalid message from a trunk circuit.DX200 Clear Code List Clear codes Alarms No alarms. 5.172 A03H . Alarms No alarms. Using facility routing. The originating exchange connects a special information tone to the subscriber. parameter CST).INTERWORKING FAILED Text in MML printouts INTERWORKING FAILED Description Interworking has taken place with a network which does not function in the defined way. The message is unspecified or the message type is nonexistent or not implemented. Possibility to change the default effect Using facility routing (command group RE. the originating exchange can connect an audible tone to the subscriber. Alarms No alarms. reception of a charging message or signal or an acknowledgement to TUP clearing in a wrong call phase.g. parameter CST). Using facility routing.Clear codes DX200 Clear Code List Alarms No alarms. 5. e. The originating exchange carries out a digit re-analysis in tree 34H. Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Using facility routing (command group RE.CIRCUIT RELEASED BY CO-EXCHANGE Text in MML printouts CRCT RELEASED BY CO-EXCHA Description A message or signal which indicates that a circuit release has been received from the trunk circuit.TRUNK CIRCUIT PROTOCOL ERROR Text in MML printouts TRUNK CRCT PROTOCOL ERROR Description An error which clears a call by definition has occurred in the trunk circuit signalling.174 A05H . 5.173 A04H . 122 Id:0900d80580635beb DN078927 Issue 1-0 . Detected by Program block SI5PRB Explanation SI5PRB sets the clear code when a charging message or an acknowledgement to clearing is received in a wrong call phase. the terminal or transit exchanges can connect an audible tone to the incoming circuit or carry out a digit reanalysis in tree 34H. 5. The message or signal in question does not belong to the group which indicates barring. Possibility to change the default effect Using facility routing (command group RE. Alarms No alarms. 5.DX200 Clear Code List Clear codes Detected by Program block SI5PRB SI7PRB Explanation SI5PRB or SI7PRB sets the clear code when it receives the message RSC (reset-circuit message). parameter CCF). Using facility routing.176 A08H .175 A07H . – Default effect on the exchange The outgoing circuit is hunted again. Such is e.CALL FAILURE FROM OUTGOING CIRCUIT Text in MML printouts CALL FAIL FROM OUT CRCT Description A message or signal indicating a failed call attempt has been received from the outgoing circuit.INTER-EXCHANGE SIGNALLING OUT OF ORDER DN078927 Issue 1-0 Id:0900d80580635beb 123 . Alarms No alarms. The originating exchange carries out a digit re-analysis in tree 32H. Possibility to change the default effect Not possible. the originating exchange can connect an audible tone to the subscriber.g. the terminal or transit exchanges can connect an audible tone to the incoming circuit or carry out a digit reanalysis in tree 32H. The signalling record indicates how many times the circuit is hunted in a call. reception of a CFL (call failure) message from the TUP. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Clear codes DX200 Clear Code List Text in MML printouts DESTINATI POINT CONGESTI Description After it has received a seizure, the program block which supervises the outgoing interexchange signalling has found a temporary disturbance in the signalling of the hunted trunk circuit. Detected by Program block SI5PRB Explanation SI5PRB sets the clear code when no acknowledgement is received from the signalling within the time supervision limit. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. The originating exchange connects a special information tone to the subscriber or performs reanalysis in the interception tree 34H. Possibility to change the default effect Using facility routing (command group RE, parameter CST), the call can be directed for reanalysis in tree 34H both in terminal and transit exchanges. Alarms No alarms. 5.177 A09H - ADDRESS COMPLETE MESSAGE TIME-OUT Text in MML printouts ADDRESS COMPLETE TIME OUT Description The ADDRESS COMPLETE message has not arrived in the originating exchange within the time supervision. Detected by Program block OC1PRB OC3PRB OUREGI Explanation OC1PRB, OC3PRB or OUREGI sets tºhe clear code when "end-of-selection" information is not received within the time supervision. – – 124 Id:0900d80580635beb DN078927 Issue 1-0 DX200 Clear Code List Clear codes Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.178 A0AH - ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED Text in MML printouts ADDRESS COMPLETE Description The Common Channel Signalling (CCS) terminating exchange has not sent the "address complete" message within the time supervision. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.179 A0CH - NO DIGITAL TRUNK Text in MML printouts NO DIGITAL TRUNK Description There is no digital trunk in the desired direction. DN078927 Issue 1-0 Id:0900d80580635beb 125 Clear codes DX200 Clear Code List Detected by Program block INREGI Explanation INREGI sets the clear code when the digit analysis ends in congestion, and the call has requested a digital connection. Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber ( call from PABX ) or performs reanalysis in the interception tree 36H ( call from subscriber ). Possibility to change the default effect Using facility routing (command group RE, parameter CDN), the call can be directed for reanalysis in tree 36H both in terminal and transit exchanges. Alarms No alarms. 5.180 A0DH - NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION Text in MML printouts NO ROUTE TO DESTINATION Description No routing to a specified transit network or to the co-exchange. The called partner cannot be reached because the network through which the call has been routed does not serve the requested co-exchange, or the transit network does not exist. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms. 5.181 A0EH - NO CIRCUIT AVAILABLE IN TRANSIT NETWORK 126 Id:0900d80580635beb DN078927 Issue 1-0 Default effect on the exchange – Possibility to change the default effect Not possible. Alarms No alarms.RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING Text in MML printouts RESEL APPL LOAD SHARE Description Reselection in the transit network applying load sharing. Alarms No alarms. Detected by Program block SI7PRB Explanation Detected by SI7PRB if the release message received from network is the national belgian ISUP cause code #14. Detected by Program block SI7PRB Explanation Detected by SI7PRB if the release message received from network is the national Belgian ISUP cause code #13. DN078927 Issue 1-0 Id:0900d80580635beb 127 . 5.182 A0FH .DX200 Clear Code List Clear codes Text in MML printouts NO CIRCUIT IN TRANS NW Description No circuits available in the transit network. Default effect on the exchange – Possibility to change the default effect Not possible. Alarms No alarms. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. 128 Id:0900d80580635beb DN078927 Issue 1-0 . Possibility to change the default effect Not possible.184 B0FH . 5. Detected by Program block OUREGI Explanation OUREGI sets the clear code when CASSIG sends message long_char_s (0081).TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EXCEEDED Text in MML printouts TRANS/TERM SIGN WAIT EXC Description No READY FOR DIALLING signal is received in time from the outgoing Y-code circuit. Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in the terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.183 B02H .Clear codes DX200 Clear Code List 5. The originating exchange connects a special information tone to the subscriber.LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED Text in MML printouts LENGTH OF CHANGED B NUM Description The new called number (B-subscriber number) obtained from the trunk circuit in conjunction with the number modification is too long. 5. – Default effect on the exchange The exhange clears the call. DN078927 Issue 1-0 Id:0900d80580635beb 129 . parameter CDP). 5.MODEM COMMUNICATION ERROR Text in MML printouts MODEM COMMUNICATION ERROR Description Internal error has occured in DSP (Digital Signal Processing) software. Special tone is connected. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block MGAPRB SI5PRB Explanation MGAPRB sets the clear code according to obtained error type from MRMPRB. Possibility to change the default effect Not possible.185 B11H . Alarms No alarms. The originating exchange carries out a digit re-analysis in tree 2CH (command group RE.186 B17H .ADDRESS INCOMPLETE Text in MML printouts ADDRESS INCOMPLETE Description Insufficient amount of digits or insufficient dialling information has been received.DX200 Clear Code List Clear codes Alarms No alarms. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms.SERVICE INCOMPATIBLE Text in MML printouts SERVICE INCOMPATIBLE Description The network terminating equipment (NTE) is not equipped with the requested ISDN data service. 5.187 B18H .Clear codes DX200 Clear Code List Possibility to change the default effect Using facility routing. Alarms No alarms.SERVICE UNAVAILABLE Text in MML printouts SERVICE UNAVAILABLE Description ISDN data call cannot be connected because the terminating node is not equipped to handle ISDN digital calls. the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2CH. 130 Id:0900d80580635beb DN078927 Issue 1-0 . Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.188 B19H . the originating exchange can connect an audible tone to the subscriber. Using facility routing. The originating exchange carries out a digit re-analysis in tree 32H (command group RE. parameter CCF). 5. 190 B21H . The originating exchange connects a special information tone to the subscriber.DX200 Clear Code List Clear codes Possibility to change the default effect Not possible. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms. Possibility to change the default effect Not possible.189 B20H . The originating exchange connects a special information tone to the subscriber. 5.NETWORK ADDRESS EXTENSION (NAE) ERROR Text in MML printouts NAE ERROR Description The ISDN PABX has received insufficient or incorrect NAE (Network Address Extension) information. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.DTE IS UNCONTROLLED Text in MML printouts DTE UNCONTROLLED Description The Data Terminal Equipment (DTE) is uncontrolled in ISDN calls. Alarms No alarms. Possibility to change the default effect Not possible. DN078927 Issue 1-0 Id:0900d80580635beb 131 . 5. Detected by Program block SI5PRB SI7PRB Explanation SI7PRB or SI5PRB sets the clear code when the BLO messages (BLOCKING) is received from the signalling.DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT Text in MML printouts DUAL SEIZURE BOTH WAY CIR Description A seizure has been detected from a bidirectional circuit after the circuit has been seized in an outgoing direction.Clear codes DX200 Clear Code List Alarms No alarms. Alarms No alarms. Possibility to change the default effect Not possible. The number of hunting attempts is indicated in the outgoing signalling record. Detected by Default effect on the exchange The outgoing circuit is hunted again.191 B23H .BLOCKING RECEIVED Text in MML printouts BLOCKING RECEIVED Description Blocking received from a bidirectional or outgoing circuit in reply to an initial address message. 5. 132 Id:0900d80580635beb DN078927 Issue 1-0 . – Default effect on the exchange The outgoing circuit is hunted again.192 B2AH . and a search for a new outgoing circuit is started for the former seizure. The latter seizure is accepted. The number of hunting attempts is indicated in the outgoing signalling record. 5. 5. Alarms No alarms.193 B2BH . Detected by Program block ICXPRB Explanation ICxPRB (inif_t) sets the clear code when a message with incorrect data is received from an IN application. Possibility to change the default effect Not possible. Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 133 . 5. The originating exchange connects a special information tone to the subscriber.INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR Text in MML printouts IN PROTOCOL ERROR Description A message has been received from an Intelligent Network (IN) application in a state where no message should have arrived.DX200 Clear Code List Clear codes Possibility to change the default effect Not possible. Default effect on the exchange The call is cleared in terminal and transit exchanges.194 B2CH .PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED Text in MML printouts PARAM NO EX OR IMPL Description A message which contains illegal parameters has been received from an Intelligent Network (IN) application. 134 Id:0900d80580635beb DN078927 Issue 1-0 .INTELLIGENT NETWORK APPLICATION RESPONSE TIME-OUT Text in MML printouts IN RESPONSE TIME OUT Description An Intelligent Network (IN) application does not respond to an event requiring acknowledgement within a time limit. Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber. Alarms No alarms.Clear codes DX200 Clear Code List Detected by Program block ICXPRB Explanation ICxPRB (inif_t) sets the clear code when an error is detected in the IN protocol. 5. The originating exchange connects a special information tone to the subscriber. Detected by Program block ICXPRB Explanation ICxPRB (inif_t) sets the clear code when the IN does not respond within the time supervision. Default effect on the exchange The call is cleared in terminal and transit exchanges. Default effect on the exchange The call is cleared in terminal and transit exchanges.195 B2DH . Possibility to change the default effect Not possible. Alarms No alarms. The originating exchange connects a special information tone to the subscriber. DN078927 Issue 1-0 Id:0900d80580635beb 135 .DX200 Clear Code List Clear codes 5. 5. Default effect on the exchange The call is cleared in terminal and transit exchanges.TCAP ERROR Text in MML printouts TCAP ERROR Description An error occurred in the connection to the service control point (SCP) provided by the transaction capabilities application part (TCAP). Detected by Program block INXPRB Explanation INXPRB sets the clear code when an error has been detected in the TCAP connection.MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED Text in MML printouts IN TRIG COUNT LIMIT Description The maximum number of Intelligent Network (IN) triggering events in a call has been reached.196 B2EH . Possibility to change the default effect Not possible.197 B2FH . Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block ICXPRB Explanation ICxPRB (inif_t) sets the clear code when the call has reached the maximum number of IN triggering events. The originating exchange connects a special information tone to the subscriber. Alarms No alarms. 5. The originating exchange connects a special information tone to the subscriber.SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT Text in MML printouts CALL IS GAPPED Description The call attempt has been interrupted by restricting the amount of calls on the basis of the selected number. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Alarms No alarms.Clear codes DX200 Clear Code List Possibility to change the default effect Not possible.ASN1 CODING OR DECODING ERROR Text in MML printouts ASN1 CODING DECODING ERRO Description An ASN. Default effect on the exchange The call is cleared in terminal and transit exchanges.198 B30H . 136 Id:0900d80580635beb DN078927 Issue 1-0 . Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber.1 coding or decoding error has been detected. Detected by Program block INXPRB Explanation INXPRB sets the clear code when ASN. Alarms No alarms.199 B31H .1 coding failed. 5. Possibility to change the default effect Not possible.CONTINUITY CHECK FAILURE Text in MML printouts CONTINUITY CHECK FAILURE Description Continuity check of the speech path has failed.CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION Text in MML printouts IN DISCONNECT BY SCP Description An Intelligent Network (IN) application in the SCP (Service Control Point) or inside the exchange has ordered the release of the call. 5. Alarms No alarms. Detected by Program block SI5PRB Explanation SI5PRB or SI7PRB sets the clear code when the continuity check of the speech path fails. DN078927 Issue 1-0 Id:0900d80580635beb 137 . Detected by Program block IDXSCP Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges.201 B33H . 5. Alarms No alarms.DX200 Clear Code List Clear codes Possibility to change the default effect Not possible. The originating exchange connects a special information tone to the subscriber.200 B32H . TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD Text in MML printouts CC NUMBER FRAUD 138 Id:0900d80580635beb DN078927 Issue 1-0 .A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER Text in MML printouts NOT INDIRECT SUBSCRIBER Description Call attempt from a number not registered as an indirect subscriber of the exchange.202 B34H . Alarms No alarms.Clear codes DX200 Clear Code List Program block SI7PRB Explanation – Default effect on the exchange The outgoing circuit is hunted again. 5.203 B35H . Detected by Program block IDXSCP Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Alarms No alarms. Possibility to change the default effect Not possible. Possibility to change the default effect Not possible. The amount of hunting attempts is indicated in the outgoing signalling record. 5. Possibility to change the default effect Not possible. Alarms No alarms.DX200 Clear Code List Clear codes Description There have been too many fraudulent attempts to use a calling card. Detected by Program block IDXSCP Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block IDXSCP Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges.CALLING CARD NUMBER SELECTED BY USER NOT FOUND Text in MML printouts CC NUMBER NOT FOUND Description The number of the calling card with keyword dialled by the user is not found.204 B36H . Possibility to change the default effect Not possible. DN078927 Issue 1-0 Id:0900d80580635beb 139 . Therefore its use is temporarily prevented. The originating exchange connects a special information tone to the subscriber. Alarms No alarms. The originating exchange connects a special information tone to the subscriber. 5. 140 Id:0900d80580635beb DN078927 Issue 1-0 . Possibility to change the default effect Not possible.205 B37H .IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD Text in MML printouts SUSPECTED FRAUD Description The Intelligent Network (IN) service has been interrupted for suspected fraud. an IN session is started. The ISUP cause code is mapped to the IN FALLBACK CODE ONE clear code and passed to the Incoming Call Control.IN FALLBACK CODE ONE Text in MML printouts IN FALLBACK CODE ONE Description An IN session is started in the Outgoing Call Control (OCxPRB). Detected by Program block INXPRB Explanation The INXPRB. Default effect on the exchange The Incoming Call Control detects an IN trigger detection point. If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined. Alarms No alarms.206 B38H . An IN trigger detection point (4) is found. The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). Detected by Program block IDXSCP Explanation – Default effect on the exchange The call is cleared in terminal and transit exchanges. Otherwise the call is cleared. signalling program handling CoreInap protocol. The originating exchange connects a special information tone to the subscriber. 5.Clear codes DX200 Clear Code List 5. DX200 Clear Code List Clear codes Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX controls the action. The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). signalling program handling CoreInap protocol. If a PRFILE parameter DN078927 Issue 1-0 Id:0900d80580635beb 141 . If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined.208 B3AH . An IN trigger detection point (4) is found.IN FALLBACK CODE THREE Text in MML printouts IN FALLBACK CODE THREE Description An IN session is started in Outgoing Call Control (OCxPRB). Otherwise the call is cleared. an IN session is started. Alarms No alarms. Otherwise the call is cleared. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX controls the action. The ISUP cause code is mapped to IN FALLBACK CODE TWO clear code and passed to Incoming Call Control. Any value different from 0 starts a new IN session. 5. Detected by Program block INXPRB Explanation The INXPRB. The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). Otherwise the call is cleared. Any value different from 0 starts a new IN session. 5. Alarms No alarms. An IN trigger detection point (4) is found. The ISUP cause code is mapped to IN FALLBACK CODE THREE clear code and passed to Incoming Call Control.207 B39H . Default effect on the exchange The Incoming Call Control detects an IN trigger detection point.IN FALLBACK CODE TWO Text in MML printouts IN FALLBACK CODE TWO Description An IN session is started in Outgoing Call Control (OCxPRB). An IN trigger detection point (4) is found. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. Otherwise the call is cleared. A value different from 0 gives start to a new IN session. Otherwise the call is cleared. signalling program handling CoreInap protocol. A value different from 0 gives start to a new IN session. Otherwise the call is cleared. 142 Id:0900d80580635beb DN078927 Issue 1-0 . signalling program handling CoreInap protocol. Alarms No alarms.209 B3BH . Default effect on the exchange Incoming Call Control is detecting an IN trigger detection Point. Detected by Program block INXPRB Explanation The INXPRB.Clear codes DX200 Clear Code List ("IN_FALLBACK_SSET_INDEX") is defined an IN session is started. Alarms No alarms. Default effect on the exchange Incoming Call Control is detecting an IN trigger detection Point. The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). Detected by Program block INXPRB Explanation The INXPRB . Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined an IN session is started. The ISUP cause code is mapped to IN FALLBACK CODE FIVE clear code and passed to Incoming Call Control. Otherwise the call is cleared.IN FALLBACK CODE FIVE Text in MML printouts IN FALLBACK CODE FIVE Description An IN session is started in Outgoing Call Control (OCxPRB). 5. Alarms No alarms. DN078927 Issue 1-0 Id:0900d80580635beb 143 . Detected by Program block INXPRB Explanation The INXPRB sends this clear code to the call control. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action.IN FALLBACK CODE FOUR Text in MML printouts IN FALLBACK CODE FOUR Description An IN session is started in Outgoing Call Control (OCxPRB). The ISUP cause code is mapped to IN FALLBACK CODE FOUR clear code and passed to Incoming Call Control. Otherwise the call is cleared. 5. The TCPROG(=TCAP) returns the error code to the INXPRB with the tc2_notice_s message. A value different from 0 gives start to a new IN session. Default effect on the exchange Incoming Call Control is detecting an IN trigger detection Point.211 B3DH . Detected by Program block INXPRB Explanation The INXPRB .IN DIALOG .DX200 Clear Code List Clear codes 5. Otherwise the call is cleared. The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined an IN session is started. which gives the reason to the IN service failure. An IN trigger detection point (4) is found.ROUTING FAILURE IN SS7 NETWORK Text in MML printouts IN SS7 ROUTING FAILURE Description The Common Channel Signalling system has returned TCAP message attached to IN ( Intelligent Network ) dialog because of a routing problem. The alarm given specifies the error code precisely. signalling program handling CoreInap protocol.210 B3CH . Detected by Program block ICXPRB Explanation ICxPRB or INREGI sets the clear code when the outgoing connection has not yetº been started.DIAL WAIT TIME EXCEEDED Text in MML printouts DIAL WAIT TIME EXCEEDED Description The dialling has not been received from the incoming circuit within the time supervision. Alarms 2617 5.213 C01H .Clear codes DX200 Clear Code List Default effect on the exchange The call is cleared in terminal and transit exchanges. 5.212 C00H . – INREGI Default effect on the exchange The call is cleared in terminal and transit exchanges. parameter CST). The originating exchange carries out a digit re-analysis in interception tree 34H or connects an audible tone. Alarms No alarms. terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Possibility to change the default effect By using facility routing. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 2CH. 144 Id:0900d80580635beb DN078927 Issue 1-0 . and the time supervision limit set for waiting for the dialling has been exceeded. Interception tree 34H (command group RE. Possibility to change the default effect Not possible.PROHIBITED DIALLING Text in MML printouts PROHIBITED DIALLING Description A digit sequence not known to the digit analysis files has been received. 214 C02H . Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Using facility routing. Alarms No alarms. Detected by Program block ICXPRB Explanation ICxPRB sets the clear code because the number does not contain enough digits for the charging attribute analysis (option). DN078927 Issue 1-0 Id:0900d80580635beb 145 . Default effect on the exchange The call is cleared in terminal and transit exchanges. the routing attribute analysis (option) or the digit analysis. Possibility to change the default effect Using facility routing transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in interception tree 2CH (command group RE. 5. The originating exchange carries out a digit re-analysis in interception tree. Using facility routing. Using facility routing.INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING Text in MML printouts INSUFFICIENT DIALLING Description An insufficient amount of digits has been received from the subscriber for number analysis. parameter CDP). ICxPRB or INREGI sets the clear code when digit analysis has resulted in congestion. the originating exchange can connect an audible tone to the subscriber. The originating exchange carries out a digit re-analysis in tree 2CH (command group RE. the originating exchange can connect an audible tone to the subscriber. parameter CDP).DX200 Clear Code List Clear codes Detected by Program block ICXPRB INREGI Explanation ICxPRB or INREGI sets the clear code when digit analysis has resulted in congestion. the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2CH. Possibility to change the default effect Using facility routing (command group RE.215 C04H .CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY Text in MML printouts A HAS NO RIGHT TO MODIFY Description The calling subscriber (A-subscriber) has no right to modify a facility from his own line.CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD Text in MML printouts A HAS DIALLED WRONG KEYW Description In a facility control call (activation/inactivation). 146 Id:0900d80580635beb DN078927 Issue 1-0 .Clear codes DX200 Clear Code List Alarms No alarms. 5. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. 5. Detected by Program block OUREGI Explanation OUREGI (ARF) sets the clear code when the subscriber gives an incorrect password in conjunction with a facility procedure. the calling subscriber (A-subscriber) has dialled a keyword which is different from the one stored in the memory of the exchange (additional subscriber data record).216 C05H . The originating exchange connects a special information tone to the subscriber or performs reanalysis in the interception tree 2CH. parameter CDP). Alarms No alarms. the call can be directed for reanalysis in tree 2CH both in terminal and transit exchanges. 217 C06H . A-subscriber tries to activate CFNR with subscriber controlled time supervision and given time value is out of allowed values. However. 5. Alarms No alarms. – OUREGI Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.218 C08H . Detected by Program block FCCPRB Explanation OUREGI (ARF) and FCCPRB sets the clear code when the activation of the facility is prevented because of restriction of outgoing calls. Alarms No alarms. Possibility to change the default effect Not possible.CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER Text in MML printouts A HAS NO RIGHT TO STORE Description The calling subscriber (A-subscriber) has performed a facility procedure which stores the called number (B-subscriber) or the third number (C-subscriber). or absent subscriber service is prohibited to this direction).DX200 Clear Code List Clear codes Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. 5.PREMATURE DIALLING DN078927 Issue 1-0 Id:0900d80580635beb 147 . FCCPRB also sets this clear code when subscriber controlled time supervision is out of allowed values. Possibility to change the default effect Not possible. the subscriber has no right to store this number (subscriber's outgoing calls are restricted. It is also possible that a mobile station has requested a bearer capability which is implemented but which the mobile station is not authorized to use.Clear codes DX200 Clear Code List Text in MML printouts PREMATURE DIALLING Description The subscriber has dialled during a register wait state. The FCCPRB sets this clear code when the subscriber tries to activate a facility which is already activated. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. parameter CDN). before hearing the dial tone.219 C09H . The call set-up is interrupted. Possibility to change the default effect Not possible. the call can be directed for reanalysis in tree 36H both in terminal and transit exchanges. i. 5. The double activation is restricted by an exhange dependent parameter. Alarms No alarms.SERVICE OR FACILITY ACTIVATION RESTRICTED Text in MML printouts SERV/FACIL ACTIVA RESTR Description The subscriber has tried to activate a service or a facility which is contradictory to other active services. Alarms No alarms. Activation is prevented also during the trial configuration. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. facilities or the subscriber category.e. 148 Id:0900d80580635beb DN078927 Issue 1-0 . The originating exchange connects a special information tone to the subscriber. or there are disturbances on the subscriber line. Possibility to change the default effect Using facility routing (command group RE. The call is cleared in terminal and transit exchanges. DN078927 Issue 1-0 Id:0900d80580635beb 149 . Alarms No alarms.INCONSISTENCY BETWEEN A. it has requested a bearer capability which is implemented by the equipment which generated this clear code but which is not available at this time.AND B-SUBSCRIBERS Text in MML printouts INCONSISTENT BETW A AND B Description The call set-up failed because of inconsistency between the data on the calling subscriber (A-subscriber) and the called subscriber (B-subscriber).SERVICE OR FACILITY USAGE RESTRICTED Text in MML printouts SERV/FACIL USAGE RESTR Description The subscriber has requested a service or a facility which is contradictory to other active services.220 C0AH . Possibility to change the default effect Using facility routing (command group RE. parameter CCF). Using facility routing. The originating exchange connects a special information tone to the subscriber ( call from PABX ) or performs reanalysis in the interception tree 32H ( call from subscriber ). Another reason is a temporary facility resource congestion in the exchange. For example. 5.221 C0BH . Detected by Default effect on the exchange In the originating exchange a digit reanalysis is performed in tree 35H. facilities or the subscriber category. but the B-subscriber has been found analog. In the case of a mobile station. a digital subscriber has requested a digital path. The originating exchange carries out a digit re-analysis in tree 32H. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 32H. the originating exchange can connect an audible tone to the subscriber.DX200 Clear Code List Clear codes 5. Default effect on the exchange – Possibility to change the default effect Not possible. parameter CCF).222 C0DH . 5. Detected by Program block AIFPRB Explanation AIFPRB set this clear code because the mobile station has requested a bearer capability which is implemented by the equipment which generated this cause but which is not available at this time.SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR Text in MML printouts SUBS SIGN MESS CONT ERR Description There has been an inconsistent or invalid message in the communication between the base station and the mobile station or between the subscriber module and the sub- 150 Id:0900d80580635beb DN078927 Issue 1-0 .BEARER CAPABILITY NOT PRESENTLY AVAILABLE Text in MML printouts BEARER CAPA NOT AVAILABLE Description Amobile station has requested a bearer capability which is implemented by the equipment which generated this cause but which is not available at this time.Clear codes DX200 Clear Code List Possibility to change the default effect Using facility routing the call can be directed for reanalysis in interception tree both in terminal and transit exchanges. Alarms No alarms. parameter CAB). Alarms No alarms. Interception tree 35H (command group RE. 5. Interception tree 32H (command group RE.223 D00H . In the originating exchange an audible tone can be connected to the subscriber using facility routing. SERVICE OR FUNCTION NOT IMPLEMENTED DN078927 Issue 1-0 Id:0900d80580635beb 151 .g a mandatory or an optional information element is missing. This clear code is used also when encountering an illogical or erroneous subscriber signalling message. Alarms No alarms.224 D01H .DX200 Clear Code List Clear codes scriber terminal. Possibility to change the default effect Not possible. 5.225 D03H . e. The originating exchange connects a special information tone to the subscriber. Alarms No alarms. The originating exchange connects a special information tone to the subscriber. 5. Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block SI6PRB Explanation SI6PRB sets the clear code when unknown values are received in network messages. Possibility to change the default effect Not possible.SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR Text in MML printouts SUBS SIGN MESS FORM ERR Description There has been a format error in the message between the base station and the mobile station or between the subscriber module and the subscriber terminal. Possibility to change the default effect Using facility routing (command group RE.Clear codes DX200 Clear Code List Text in MML printouts SERV OR FUNC NOT IMPLEM Description A service or a function requested by the subscriber has not been implemented in the exchange. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Possibility to change the default effect Not possible. the originating exchange can connect an audible tone to the subscriber.226 D04H . Alarms No alarms. 5. 5. The originating exchange carries out a digit re-analysis in tree 34H.SUBSCRIBER SIGNALLING PROTOCOL ERROR Text in MML printouts SUBS SIGN PROTOCOL ERROR Description The signalling messages have arrived in incorrect order with respect to the call phase. This clear code is also used in PABX signalling protocol errors. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges.AOCC CHARGING ERROR 152 Id:0900d80580635beb DN078927 Issue 1-0 . parameter CDN). parameter CST). terminal and transit exchanges can carry out a digit re-analysis in tree 34H.227 D06H . Alarms No alarms. This protocol error has been registered in the communication between the base station and the mobile station or between the subscriber module and the subscriber terminal. The originating exchange carries out a digit re-analysis in tree 36H (command group RE. Using facility routing. The originating exchange connects a special information tone to the subscriber. Charging) supplementary service does not acknowledge the Charge Advice Information (CAI).DX200 Clear Code List Clear codes Text in MML printouts AOCC CHARGING ERROR Description The call has been cleared because the mobile station which has been equipped with AOC-C (Advice of Charge. SI6PRB sets the clear code when a terminal equipment does not answer within the time supervision.NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT Text in MML printouts NO USER RESPONDING Description The user device has not responded to a call establishment message with either ALERTING or CONNECT message within the time supervision. DN078927 Issue 1-0 Id:0900d80580635beb 153 .228 D07H . The originating exchange connects a busy tone to the subscriber. Possibility to change the default effect Not possible. – SI6PRB Default effect on the exchange The call is cleared in transit and terminal exchanges. 5. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. Detected by Program block SI1PRB Explanation SI1PRB sets the clear code when a PABX does not answer within the time supervision. Alarms No alarms. Call Forwarding Unconditional (CFU) is prevented by this clear code if the amount of call forwarding steps has been exceeded. 08 PROTOCOL TIMER EXPIRES Text in MML printouts GSM ERH408 TIME OUT Description The procedure has started upon the expiry of a timer in agreement with GSM Recommendation 04. 5. Alarms No alarms. Interception tree 33H (command group RE. Detected by Default effect on the exchange The call is cleared in transit and terminal exchanges. Detected by Default effect on the exchange The call is cleared in transit and terminal exchanges. The originating exchange connects a special information tone to the subscriber. The originating exchange connects an a udible tone to the subscriber. the call can be directed for reanalysis in tree 32H both in terminal and transit exchanges. Possibility to change the default effect Not possible. Alarms No alarms.229 D08H . parameter CBB).GSM ERH 4. 5.08. 154 Id:0900d80580635beb DN078927 Issue 1-0 .230 D0BH .Clear codes DX200 Clear Code List Possibility to change the default effect Using facility routing (command group RE. parameter CCF). Possibility to change the default effect Not possible.DUAL LOG-IN Text in MML printouts DUAL LOG-IN Description Dual log-in to an operator position. DN078927 Issue 1-0 Id:0900d80580635beb 155 . FCCPRB – Default effect on the exchange Call is disconnected with tone or announcement.ISDN-SUBSCRIBER FACILITY DIALLING REJECTED Text in MML printouts FACILITY REJECTED Description ISDN-subscriber has dialled wrong facility procedure in activation. Alarms No alarms.232 D10H . the service code is wrong. 5. square character in the middle of facility procedure.MANDATORY INFORMATION ELEMENT MISSING Text in MML printouts MANDATORY IE MISSING Description A mandatory information element was missing in a message.231 D0FH .DX200 Clear Code List Clear codes Alarms No alarms. 5. Detected by Program block SI1PRB Explanation Detected by SI1PRB when a SETUP message does not contain a mandatory information element. for example Bearer Capability in a SETUP message. Possibility to change the default effect Not possible. for example Bearer Capability. (for example. deactivation or use of facility.) Detected by Program block FCCPRB IC6PRB Explanation IC6PRB. 233 D11H .INVALID INFORMATION ELEMENT CONTENT Text in MML printouts INVALID IE CONTENT Description Information element contents in a message are invalid. Default effect on the exchange A call from an access is not accepted. 156 Id:0900d80580635beb DN078927 Issue 1-0 .Clear codes DX200 Clear Code List Default effect on the exchange The message (SETUP) is not accepted and the call is cleared. Alarms No alarms. for example Bearer Capability in a SETUP message. 5. Detected by Program block SI1PRB Explanation Detected by SI1PRB when a SETUP message contains an invalid mandatory information element. Possibility to change the default effect Not possible. Possibility to change the default effect Not possible. Alarms No alarms. for example Bearer Capability. DX200 Clear Code List Clear code index 6 Clear code index NUMBER 0000H 0001H 0003H 0004H 0005H 0006H 0007H 0008H 0009H 000AH 000BH 000CH 000EH 000FH 0010H 0011H 0012H 0013H 0015H 0016H 0018H 0020H 0025H 0031H 0100H 0101H 0102H 0103H 0201H 0202H 0203H 0204H 0206H 0207H 020BH 020EH NAME NORMAL END OF CALL SUSPENDED CALL CALL DURATION BELOW SUPERVISION TIME B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT CALLED SUBSCRIBER BUSY TIME-OUT FOR B-SUBSCRIBER ANSWER CALL WAITING TIME-OUT CALLED SUBSCRIBER NOT CONNECTED CALL ALREADY WAITING INTERVENTION ALREADY ON REROUTING DUE TO B-SUBSCRIBER FACILITY OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE MALICIOUS CALL TRACING INTERMEDIATE CHARGING ABSENT SUBSCRIBER OPERATOR PRIORITY ACCESS NO PAGING RESPONSE CALL TRANSFER RECALL DUE TO C-SUBSCRIBER ANSWER TIME-OUT NORMAL UNSPECIFIED SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE INTERMEDIATE CHARGING IN THE END OF THE PHASE CHARGING ANNOUNCEMENT SUCCESS IN INTERCEPTION CALL DROP BACK RELEASE NOT ENOUGH CREDIT TO CALL CIRCUIT RE-SEIZED CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE CALL RECORD RELEASED DURING CALIBRATION CHARGING IN WRONG PHASE OF CALL CALL RELEASED CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT B-CHANNEL UNACCEPTABLE ESTABLISHED B-CHANNEL CALL REJECTED SUBSCRIBER CONGESTION CLEAR IN DETAILED CHARGING CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE DN078927 Issue 1-0 Id:0900d80580635beb 157 . OR C-NUMBER IS NOT REGISTERED CALLED SUBSCRIBER LINE BLOCKED CHANGE IN NUMBERING PLAN CLOSED USER GROUP RESCTRICTION BEARER SERVICE NOT PROVIDED TELESERVICE NOT PROVIDED CALLED SUBSCRIBER HAS CALL DIVERSION BARRING TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE INCOMING CALLS BARRED WITHIN THE CUG SUBSCRIBER NOT A MEMBER OF THE CUG OUTGOING CALLS BARRED WITHIN THE CUG NO CUG SELECTED UNKNOWN CUG INDEX ATTENUATOR CONGESTION INTERWORKING UNIT CONGESTION 158 Id:0900d80580635beb DN078927 Issue 1-0 .Clear code index DX200 Clear Code List NUMBER 020FH 0210H 0211H 0213H 0215H 0216H 0217H 0218H 0219H 0220H 0252H 0300H 0301H 0304H 0305H 0306H 0307H 0308H 0309H 030AH 030BH 030CH 030DH 030EH 030FH 0310H 0311H 0312H 0315H 0317H 031AH 031CH 031DH 0321H 0322H 0400H 0401H NAME CHANGE OF OUTGOING CIRCUIT NULL NUP NETWORK. REJECTED DIVERTED CALLS NETWORK. USER NOT IN CUG CALL DROP BACK MISDIALLED TRUNK PREFIX TEMPORARY OUT OF ORDER OUT OF CATCHMENT AREA TRANSLATION OUT-OF-SERVICE ANONYMOUS CALLS REJECTION UNTERMINATED CALL TO A PORTED NUMBER CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR CALLED SUBSCRIBER LINE OUT OF SERVICE CALLED SUBSCRIBER LINE FAULTY ACCESS TO B-SUBSCRIBER LINE RESTRICTED B-NUMBER UNUSED B-NUMBER CHANGED TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER REANSWER TIME OUT B. CALL CLEARED LONG AON REQUEST REGISTER ANALYSIS FAILED QUEUEING TIME EXCEEDED PARITY ERROR FROM PBRU/MFCU DEVICE MODULE OR V5 INTERFACE NOT AVAILABLE CALL INTERRUPTED DURING REGISTER ANALYSIS SUBSCRIBER MODULE RESTARTED FORCED CLEAR OF A CALL DN078927 Issue 1-0 Id:0900d80580635beb 159 .DX200 Clear Code List Clear code index NUMBER 0402H 0403H 0404H 0405H 0406H 0407H 0408H 0409H 040AH 040BH 0506H 0508H 0509H 050BH 050CH 050DH 050FH 0600H 0601H 0602H 0603H 0604H 0606H 0607H 0608H 0609H 060BH 060DH 060EH 060FH 0700H 0701H 0702H 0704H 0705H 0706H 0707H 070AH NAME REGISTER TOTAL TIME EXCEEDED MFCU DEVICE CONGESTION PBRU DEVICE CONGESTION ERRONEOUS SERVICE REQUEST FROM CO-PROCESS CONNECTION FAILED IN GSW/SWI ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED CONNECTION FAILED IN SSW/SWI CIRCUIT CONGESTION DUE TO TRAFFIC TYPE HOP COUNTER EXHAUST LINES OF LINE HUNTING GROUPS BARRED CHARGING ERROR FILE ERROR MODULE ROUTE OR SSW CONGESTION MFC-ASS-CHANNEL CLOSING MISSED FACILITY CONTROL FAILED UNSUITABLE MODULE CIRCUIT FILE RECORD CONGESTION MODULE OR V5 CONGESTION REGISTER CONGESTION NO RESPONSE FROM PARTNER PROGRAM BLOCK INTERNAL CALL LINK CONGESTION CONFERENCE DEVICE CONGESTION POLARITY REVERSAL FAILURE CHARGING NOT STARTED CALL CLEARED BY MML OVERLOAD CONGESTION STAGE CIRCUIT CONGESTION UNIT RESTARTED SUBSCRIBER MODULE OR V5 INTERFACE FAILURE. SEND SPECIAL INFORMATION TONE NETWORK. UNALLOCATED NUMBER NETWORK. LINE OUT OF SERVICE NETWORK. SUBSCRIBER NUMBER CHANGED 160 Id:0900d80580635beb DN078927 Issue 1-0 .Clear code index DX200 Clear Code List NUMBER 070BH 070CH 070DH 070EH 0710H 0711H 0712H 0713H 0714H 0715H 0716H 0718H 0719H 071AH 071BH 071CH 071DH 0801H 0802H 0803H 0804H 0806H 0809H 080AH 080BH 080CH 080DH 080EH 080FH 0810H 0811H 0813H 0814H 0815H 0816H 0817H 0818H 0819H NAME MODEM ERROR OVERLOAD CONTROL SYSTEM ERROR ANNOUNCEMENT SERVICE FAILURE CONFIGURATION ERROR NO ANALYSIS FOR CARRIER ACCESS CODE TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE NO ISUP ROUTE ATTRIBUTE DIRECTED ROUTING MISMATCH REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION NO RESOURCE AVAILABLE FOR CALL IDENTIFIED CHANNEL NOT EXIST REQUESTED CHANNEL NOT AVAILABLE PACKET CONTROL UNIT CONGESTION POINT-TO-POINT PROTOCOL ERROR LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED INVALID CALLING SUBSCRIBER CATEGORY OUTGOING CIRCUIT CONGESTION IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT OUTGOING CIRCUIT OUT OF ORDER INCOMING CIRCUIT OUT OF ORDER CIRCUIT CONGESTION FACILITY NOT SUPPORTED NETWORK FAILURE SWITCHING EQUIPMENT CONGESTION CIRCUIT GROUP CONGESTION ACCESS BARRED TO THE CALLED SUBSCRIBER CALL FAILED. DX200 Clear Code List Clear code index NUMBER 081AH 081DH 081EH 081FH 0820H 0821H 0822H 0824H 0828H 0829H 0830H 0832H 0833H 0851H 0900H 0901H 0905H 090CH 090EH 090FH 0A01H 0A02H 0A03H 0A04H 0A05H 0A07H 0A08H 0A09H 0A0AH 0A0CH 0A0DH 0A0EH 0A0FH 0B02H 0B0FH 0B11H 0B17H NAME CONGESTION IN TERMINAL EXCHANGE CONGESTION IN INTERNATIONAL CALL CONTROLLED NOT READY NETWORK. OVERLOAD CONGESTION NETWORK MESSAGE CONTENT ERROR INVALID TRANSIT NETWORK SELECTION RECOVERY ON TIMER EXPIRY PCM FAULTY CONGESTION FROM NATIONAL NETWORK DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION NUMBER PORTABILITY ROUTING ERROR DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNALLING NO MF FORWARD SIGNAL TOO LONG MF FORWARD SIGNAL TOO LONG MF BACKWARD SIGNAL PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT PREMATURE ANSWER ANSWER AFTER B BUSY CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) INVALID MESSAGE FROM TRUNK CIRCUIT INTERWORKING FAILED TRUNK CIRCUIT PROTOCOL ERROR CIRCUIT RELEASED BY CO-EXCHANGE CALL FAILURE FROM OUTGOING CIRCUIT INTER-EXCHANGE SIGNALLING OUT OF ORDER ADDRESS COMPLETE MESSAGE TIME-OUT ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED NO DIGITAL TRUNK NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION NO CIRCUIT AVAILABLE IN TRANSIT NETWORK RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EXCEEDED LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED MODEM COMMUNICATION ERROR ADDRESS INCOMPLETE DN078927 Issue 1-0 Id:0900d80580635beb 161 . Clear code index DX200 Clear Code List NUMBER 0B18H 0B19H 0B20H 0B21H 0B23H 0B2AH 0B2BH 0B2CH 0B2DH 0B2EH 0B2FH 0B30H 0B31H 0B32H 0B33H 0B34H 0B35H 0B36H 0B37H 0B38H 0B39H 0B3AH 0B3BH 0B3CH 0B3DH 0C00H 0C01H 0C02H 0C04H 0C05H 0C06H 0C08H 0C09H 0C0AH 0C0BH 0C0DH 0D00H 0D01H NAME SERVICE UNAVAILABLE SERVICE INCOMPATIBLE NETWORK ADDRESS EXTENSION (NAE) ERROR DTE IS UNCONTROLLED DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT BLOCKING RECEIVED PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR INTELLIGENT NETWORK APPLICATION RESPONSE TIME-OUT MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED TCAP ERROR ASN1 CODING OR DECODING ERROR SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION CONTINUITY CHECK FAILURE A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD CALLING CARD NUMBER SELECTED BY USER NOT FOUND IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD IN FALLBACK CODE ONE IN FALLBACK CODE TWO IN FALLBACK CODE THREE IN FALLBACK CODE FIVE IN FALLBACK CODE FOUR IN DIALOG .ROUTING FAILURE IN SS7 NETWORK DIAL WAIT TIME EXCEEDED PROHIBITED DIALLING INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER PREMATURE DIALLING SERVICE OR FACILITY ACTIVATION RESTRICTED SERVICE OR FACILITY USAGE RESTRICTED INCONSISTENCY BETWEEN A.AND B-SUBSCRIBERS BEARER CAPABILITY NOT PRESENTLY AVAILABLE SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR 162 Id:0900d80580635beb DN078927 Issue 1-0 . DX200 Clear Code List Clear code index NUMBER 0D03H 0D04H 0D06H 0D07H 0D08H 0D0BH 0D0FH 0D10H 0D11H NAME SERVICE OR FUNCTION NOT IMPLEMENTED SUBSCRIBER SIGNALLING PROTOCOL ERROR AOCC CHARGING ERROR NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT GSM ERH 4.08 PROTOCOL TIMER EXPIRES DUAL LOG-IN ISDN-SUBSCRIBER FACILITY DIALLING REJECTED MANDATORY INFORMATION ELEMENT MISSING INVALID INFORMATION ELEMENT CONTENT DN078927 Issue 1-0 Id:0900d80580635beb 163 . IC2PRB.1 BCIE CAC CAI CCSU CFU CFB CFNR CUG DTE EIR HLR ISUP ITUP IN ICxPRB MFC MFCU MFST MWD NUP PBRU PCM PNP SCP SSP TCAP TUP VLR Advice of Charge (charging) Abstract Syntax Notation One Bearer Capability Information Element Carrier Access Code Charge Advice Information Common Channel Signalling Unit Call Forwarding Unconditional Call Forwarding Busy Call Forwarding On No Reply Closed User Group Data Terminal Equipment Equipment Identity Register DX HLR ISDN User Part International Telephone User Part Intelligent Network IC1PRB.Glossary DX200 Clear Code List Glossary AOC-C ASN. IC3PRB and IC9PRB Multifrequency Code Multifrequency Code Unit Multi Frequency Signalling Terminal plug-in unit Messages Waiting Data National User Part Push Button Receiver Unit Pulse Code Modulation Private Numbering Plan Service Control Point Service Switching Point Transaction Capabilities Application Part Telephone User Part Visitor Location Register 164 Id:0900d80580635beb DN078927 Issue 1-0 .