Pc3 Service Manual

March 27, 2018 | Author: Florin Vîță | Category: Personal Computers, Bios, Floppy Disk, Dynamic Random Access Memory, Booting


Comments



Description

Service Provider InfoNr.: BCA01018E Announcement of Embedded/Sinem PC in self-service systems AUTHOR: Email address: WN Service HQ PM [email protected] Embedded/Sinem PC in self-service systems: General The Embedded PC is replacing the SENIC 651/661 series in our self-service systems. The Embedded PC is available as standard in a high end variant and a less expensive low end variant. The housing is made of metal and the dimensions are almost identical with those of the SCENIC 6XX series. The main differences from the previous SCENIC 6XX series are as follows: - S3 Grafik Controller on board - Audio Controller AC97 on board (only High End Version) - inset of V.24 Multiportcard “FitWin” - configuration optionally with the PC card ‚PanelLink-Bridge’ to connect a LCD-Monitor ©Copyright Wincor Nixdorf GmbH & Co. KG, 2001 Page: 1 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 AC97 S3 (VIA) 4 PCI 1 ISA / PCI Nr.2 GB 52 x IDE VIA .2 GB IDE 52 x IDE S3 (VIA) 4 PCI 1 ISA / PCI Sinem High End Material number 01750031810 Pentium III 600 256 KB 64 MB 10. EPP. KG.Service Provider Info Overview of PC variants PC type Sinem Low End Material number 01750034503 Celeron 433 128 KB 64 MB 10. ECP) 1 x keyboard (PS/2) ©Copyright Wincor Nixdorf GmbH & Co.: BCA01018E Processor SL cache RAM Dimm HDD CD-ROM Audio On Board VGA On Board Slots System affiliation The Embedded PC will be deployed in the self-service systems: ProCash 2150 ProCash 2050 ProCash 2000 ProCash 3100 ProCash 2156 Pro Info Pro Consult Orbiter Hardware Technical data Intel Celeron 433 MHz (Low End Version) ATX motherboard Chip set VIA VT8605 / 686 A Microprocessor Intel Celeron 433 MHz Processor base Slot 1 Front side bus 66 MHz Main memory 64 MB (default) DIMM slot 2 (SDRAM) Flash EPROM BIOS update via diskette possible Interfaces (device rear side) 1 x serial (9 pin) 1 x parallel (25 pin. 2001 Page: 2 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . 2001 Page: 3 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 .44 MB Nr. EPP.Service Provider Info 1 x mouse (PS/2) 2 x USB 1 x CRT Interfaces (internal) 2 x IDE. WIN 95 / 98 / NT) OS/2 Intel Pentium III 600 MHz (High End Version) ATX motherboard Chip set VIA VT8605 / 686 A Microprocessor Intel Pentium III 600 MHz Processor base Slot 1 Front side bus 100 MHz Main memory 64 MB (default) DIMM slot 2 (SDRAM) Flash EPROM BIOS update via diskette possible Interfaces (rear side) 2 x serial (9 pin) 1 x parallel (25 pin. 10 GB ATAPI (52x) Slots 1 x AMR (for PL option) 1 x AGP 4 x PCI 1 x ISA / PCI Electrical ratings Supply voltage Line frequency Max. 1. ECP) 1 x keyboard (PS/2) 1 x mouse (PS/2) 2 x USB ©Copyright Wincor Nixdorf GmbH & Co. KG. power dissipation Dimensions Dimensions (WxDxH) Compatibility (references) 110 – 120V / 220 – 240V (selectable) 50 – 60 Hz 145 Watt 135 x 440 x 400 mm Microsoft operating systems (DOS. primary & secondary 1 x floppy 1 x Wake-on-LAN 1 x Wake-on-Modem 3.5".: BCA01018E Floppy disk drive Hard disk controller Hard disk capacity CD-ROM drive min. 44 MB Nr. 1.5".Service Provider Info 1 x CRT 1 x joystick 1 x microphone 1 x Line in 1 x Line out / speaker out Interfaces (internal) 2 x IDE. 10 GB ATAPI (52x) Slots 1 x AMR (for PL option) 1 x AGP 4 x PCI 1 x ISA / PCI Electrical ratings Supply voltage Line frequency Max. KG. primary & secondary 1 x floppy 1 x Wake-on-LAN 3.: BCA01018E Floppy disk drive Hard disk controller Hard disk capacity CD-ROM drive min. power dissipation Dimensions Dimensions (WxDxH) Compatibility (references) 110 – 120V / 220 – 240V (selectable) 50 – 60 Hz 145 Watt 135 x 440 x 400 mm Microsoft operating systems (DOS. 2001 Page: 4 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . WIN 95 / 98 / NT) OS/2 ©Copyright Wincor Nixdorf GmbH & Co. Service Provider Info Device rear side Nr. 2001 Page: 5 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 .: BCA01018E 1 2 3 4 5 6 7 8 Power input 9 10 11 12 13 14 15 LPT1 COM 2 to COM 4 (from bottom) LCD monitor (panel link) (optional) Keyboard and mouse 2 USB interfaces COM 1 CRT monitor Loudspeaker / headphone / Line (out) Line (in) Microphone MIDI / Game port AGP slot 4 PCI slots ISA / PCI slot ©Copyright Wincor Nixdorf GmbH & Co. KG. This battery needs to be changed about every three years. Only use the same battery type or a type recommended by Wincor Nixdorf GmbH & Co. time and the CMOS. 2001 Page: 6 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . ©Copyright Wincor Nixdorf GmbH & Co. KG. KG.Service Provider Info ATX motherboard Nr.: BCA01018E 1 2 3 4 5 6 7 8 9 COM 2 to COM 4 (from bottom) Loudspeaker / headphone / Line (out) & Line (in) & microphone MIDI / game port CRT monitor LPT1 COM 1 2 USB interfaces Keyboard and mouse Fan 1 (CPU) 10 11 12 13 14 15 16 17 18 IrDA CPU Floppy IDE (primary) IDE (secondary) Fan 2 (system) Battery Wake-on-Modem Wake-on-LAN Lithium battery (CR2032) There is a lithium battery on the motherboard for preserving the date. The local regulations for the disposal of special waste should be observed when it comes to disposal. Danger of explosion if replaced improperly. Service Provider Info Position of jumpers Nr. KG. 2001 Page: 7 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 .: BCA01018E 1 JP 16 / JP 17 2 JP 19 / JP 20 3 JP 6 Jumper settings Jumper 1: Clock signal Jumper 2: Assistant frequency 4 5 6 JP 1 JP 3 JP 2 Default 66 MHz 100 MHz Automatic detection (Default) 133 MHz Jumper 3: Not jumpered Jumper 6: Erase CMOS Normal (Default) Erase CMOS ©Copyright Wincor Nixdorf GmbH & Co. 2001 Page: 8 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 .Service Provider Info Jumper 16 / Jumper 17: Serial interface 2 Jumper 19 / Jumper 20: Audio Loudspeaker / headphone Line (out) Default Nr.: BCA01018E IRQ table System clock Keyboard PCI Serial port COM2 Serial port COM1 Not used FDD Parallel port LPT1 RTC VGA / not used Serial port COM3 / not used Serial port COM4 / not used Mouse controller / not used Numeric processor IDE controller (primary) IDE controller (secondary) Pin assignment COM1 (9 pin DSUB-M) Pin Name 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI COM2 to COM4 (9 pin DSUB-F) Pin Name 1 + 12 VDC FS 2 RXD 3 TXD IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 ©Copyright Wincor Nixdorf GmbH & Co. KG. HOSTACK FAULT.Service Provider Info 4 5 6 7 8 9 DTR GND DSR RTS CTS + 5 VDC FS Nr. ACKREVERSE SLCT AUTOFD. KG.: BCA01018E LPT1 (25 pin DSUB-F) I/O Standard Pin interface 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I I O I O STROBE D0 D1 D2 D3 D4 D5 D6 D7 ACK BUSY PE SLCT AUTOFD FAULT INIT 17 18 19 20 21 22 23 24 25 O SLCTIN GND GND GND GND GND GND GND GND Extended Capability Port (ECP) STROBE D0 D1 D2 D3 D4 D5 D6 D7 ACK BUSY. PERIPHACK PE. 2001 Page: 9 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . PERIPHREQST INIT. REVERSERQS T SLCTIN GND GND GND GND GND GND GND GND Enhanced Parallel Port (EPP) WRITE D0 D1 D2 D3 D4 D5 D6 D7 INTR WAIT PE SLCT DATASTB FAULT RESET ADDRSTB GND GND GND GND GND GND GND GND Keyboard / mouse Pin Name 1 Data 2 NC 3 GND 4 + 5 V FS 5 Clock ©Copyright Wincor Nixdorf GmbH & Co. 3 V (differential USB signal USB_D+) 3.3 V (differential USB signal USB_D+) GND + 5 V FS NC Nr.3 V (differential USB signal USB_D-) 3.: BCA01018E CRT (15 pin DSUB-F) Pin Name 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 + 5 V FS 10 GND 11 NC 12 MONID 1 13 HSYNC 14 VSYNC 15 MONID 2 ©Copyright Wincor Nixdorf GmbH & Co.Service Provider Info 6 USB Pin 1 2 3 4 5 6 7 8 IrDA Pin 1 2 3 4 5 Name VCC NC IRRX (infrared) GND IRTX (infrared) Name + 5 V FS GND 3.3 V (differential USB signal USB_D-) 3. 2001 Page: 10 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . KG. 2001 Page: 11 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . 3.5 in.: 7531114 A Standard CMOS features … Drive A Drive B Video Halt On Advanced BIOS features Virus Warning CPU Internal Cache External Cache CPU L2 Cache ECC Checking Processor Number Feature Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Security Option PS/2 Mouse Function Disabled Enabled Enabled Disabled Disabled Enabled Floppy HDD-0 CDROM Enabled Disabled Disabled On Normal Disabled 1.00 PG Rel. KG. None EGA/VGA All .44M. 32 Customer/application specific ©Copyright Wincor Nixdorf GmbH & Co.Service Provider Info BIOS-SETUP BIOS-SETUP Bios version: V6.: BCA01018E Setup Disabled Default Enabled Mouse connected OS Select For DRAM > 64 MB Non-OS2 Default OS2 if OS2 and memory > 64 MB Video BIOS Shadow Enabled C8000-CBFFF Shadow Disabled … Advanced Chipset features DRAM Timing By SPD DRAM Clock SDRAM Cycle Length Bank Interleave DRAM Drive Strength Memory Hole P2C/C2P Concurrency Fast R-W Turn Around System BIOS Cacheable Video RAM Cacheable Frame Buffer Size Disabled Host Clock 3 Disabled Auto Disabled Enabled Disabled Disabled Disabled 2M 2 MB Video memory ATMs 8M 8 MB Video memory Terminals 4. 16. But Keyboard Nr. 01 on the strength of floppy problems Connection of standard printer ECP Connection of ECP printer COM3 switched off 3E8H COM3 activated IRQ reservation COM4 switched off COM4 activated Alternatively IRQ10 (IRQ´s geshared) Audio onboard switched off Enabled Audio onboard activated No standard SB function Enabled SB compatibility necessary Sound Blaster SB I/O Base Address Disabled 220H ©Copyright Wincor Nixdorf GmbH & Co.01. 2001 Page: 12 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 .ASKIR Infrared mode Default only by installed Backpack driver fewer than NT 4. KG. DOS 4.: BCA01018E No audio wanted Auto Activate audio CRT output only activated VGA LCD connected SVGA LCD connected (default) XGA LCD connected IDE HDD Block Mode Onboard FDD Controller Onboard Serial Port 1 Onboard Serial Port 2 UART 2 Mode Onboard Parallel Port Onboard Parallel Mode ECP Mode use DMA Onboard Serial Port 3 Serial Port 3 use Onboard Serial Port 4 Serial Port 4 use Onboard Legacy Audio Default HPSIR.Service Provider Info AGP Aperture Size AGP-4X Mode AGP Driving Control On Chip USB On Chip Sound On Chip Modem CPU to PCI Write Buffer PCI Dynamic Bursting PCI Master 0 WS Write PCI Delay Transaction PCI #2 Access #1 Retry AGP Master 1 WS Write AGP Master 1 WS Read Integrated Peripherals On Chip IDE Channel0 On Chip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA Init Display First LCD Display Mode Enabled Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto PCI Slot Mode 0 Mode 1 Mode 2 Mode 3 Enabled Enabled 3F8/IRQ4 2F8/IRQ3 Standard 378/IRQ7 3BC/IRQ7 Normal 1 Disabled IRQ10 Disabled 270H IRQ11 Disabled Default Disabled for PC2100 64M Disabled Auto Disabled Disabled Disabled Enabled Enabled Enabled Disabled Enabled Disabled Disabled Nr.11. OS/2 3. 2001 Page: 13 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . Component Grafic Controller Up to now C&T69000 (Dotcard) or Matrox G200 Audio Controller TT-Solo (optionally Audio card) RocketPort Fitwin vide: VIA-AC97 New S3 (VIA) Necessary driver on CD* under -> CPU/Sinem/Video or Intranet/Extranet -> Software Download on CD* under -> CPU/Sinem/Audio or Intranet/Extranet -> Software Download on CD* under -> MUX/Fitwin Multiport Card ©Copyright Wincor Nixdorf GmbH & Co.Service Provider Info SB IRQ Select SB DMA Select MPU-401 MPU-401 I/O Address Game Port (200-207H) Power Management Setup > ACPI function Disabled Power Management Press Enter Power Management User Define HDD Power Down Disabled Doze Mode Disabled Suspend Mode Disabled PM Control by APM No Video Off Option Suspend -> Off Video Off Method V/H SYNC+Blank Modem use IRQ 3 Soft-Off by PWRBTN Instant-Off State After Power Failure On Wake Up Events Not relevant IRQ 5 DMA 0 Disabled 330-333H Enabled Nr. KG.: BCA01018E > PNP/PCI configurations PNP OS Installed Reset Configuration Data Resources Controlled By > IRQ Resources > DMA Resources PCI/VGA Palette Snoop Assign IRQ for VGA Assign IRQ for USB No Disabled Manual Press Enter Press Enter Disabled Disabled Disabled with Win NT. The following table describes the changes to the SCENIC 6XX and the location of the drivers on the FRM CD or in the Intranet/Extranet. OS2. DOS Yes with Win 95/98 (ME/2000) Reservation for ISA card will follow Reserve IRQ Reserve DMA Technical Changes in the PC The technical changes to the PC and its components mean that new drivers are also required. There is no provision for the repair of modules and components in the regions. Separate test programs or program extensions are to be used for add-on cards (DC cards. Power On Self-Test Power-up test after switch-on SDIAG/AMIDIAG/PC Doctor test programs Please use an SDIAG version that has been modified for the Embedded PC in order to test the system. KG. This will soon be available to download from the Intranet/Extranet under Software/Test Programs. Faulty parts are replaced in their entirety.: BCA01018E Expansion of the main memory: There are two slots on the system module (Bank 1 and Bank 2) for installing the memory modules. There is no need for preventive maintenance or for electrical or mechanical adjustments. Additional information can be gathered by running a self-test on a number of components and by using offline test programs (SDIAG). firmware and separate diagnostics programs (e.24 multiport cards. ©Copyright Wincor Nixdorf GmbH & Co. Support by the engineer: Faults can primarily be located on the basis of the information provided by the operator. For a more comprehensive and thorough-going test we recommend using the AMIDIAG test program or PCDoctor. DIMMs (Dual Inline Memory Modules) are used. The maximum memory configuration is 512 Mbytes with 100/133 MHz SDRAM memory modules. etc.Service Provider Info BCA01013 or Intranet/Extranet -> BCA01015 Software Download * The actual CD „CSC-FRM“ will be attached at the delivery of the system. DC cards). The SDIAG/AMIDIAG/PC Doctor test programs cannot be used to test all components in the system unit. 2001 Page: 14 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 . Nr.) Firmware/drivers & utilities The “CSC-FRM“ CD is enclosed with each self-service system delivered and contains current drivers. Support concept: Support by the operator: The user guide contains information on “Care and cleaning” as well as “Safety advice” for the operator. Maintenance aids The following test options are available for testing the Embedded PC.g. V. Mailto:Servicesupport@wincor-nixdorf. Spare parts: Name Embedded PC High-end Embedded PC Low-end 64MB SDRAM Mainboard Power Supply CD-ROM Drive Multi Read 52x Floppy Disk Drive 1 Hard Disk 10. 2001 Page: 15 of 15 Confidential Announcement of Embedded/Sinem PC in self-service systems Status: 30 April 2001 .Service Provider Info Documentation: Nr. KG.com ©Copyright Wincor Nixdorf GmbH & Co.5AT CPU PIII Celeron/MMX 433MHZ CMOS Lithium Batterie Typ CR2032 Panel Link Bridge Material no: 01750031810 01750034503 0131701830 01750031813 01750031969 01750034491 01750015569 01750034137 A3C40017269 A3C40009602 01750032008 Training Separate training courses are not planned.2 GB 3.: BCA01018E The Embedded PC service manual is not available separately. but is integrated in the system-specific service documentation for the product.
Copyright © 2024 DOKUMEN.SITE Inc.