032731-10 Rev.A Upgrading an OmniSwitch to 6.4.4.R01 Overview These instructions documents how to upgrade the following OmniSwitch products to 6.4.4.R01 software and firmware. The upgrade can be performed using the CLI or WebView. Alcatel-Lucent recommends using WebView to perform the upgrade. Release 6.4.4.R01 is supported on the following switches. Click on the link to go to instructions for a specific switch. • “OmniSwitch 9000E” on page -4 • “OmniSwitch 6855” on page -19 • “OmniSwitch 6850” on page -32 • “OmniSwitch 6400” on page -46. Note. Release 6.4.4.R01 is not supported on the OS 9600, 9700, or 9800. Also note that the OS6850E ships with the latest software and does not require any upgrades. Prerequisites WARNING: For all switch models, you MUST complete the Image File upgrade BEFORE upgrading the U-Boot and Miniboot Files. Please verify that the switch has been properly upgraded to 6.4.4.R01 before upgrading the U-boot and Miniboot. This instruction sheet requires that the following conditions exist, or are performed, before upgrading: • The person performing the upgrade must: - be the responsible party for maintaining the switch’s configuration be aware of any issues that may arise from a network outage caused by improperly loading this code understand that the switch must be rebooted and network users will be affected by this procedure have a working knowledge of the switch to configure it to accept an FTP connection through the EMP or Network Interface (NI) Ethernet port. • Read the 6.4.4.R01 GA Release Notes prior to performing any upgrade for information specific to this release. Note. Do not proceed until all the above prerequisites have been met. Any deviation from these upgrade procedures will result in the malfunctioning of the switch. All steps in these procedures should be reviewed before beginning. Upgrading an OmniSwitch to 6.4.4.R01, Part No. 032731-10 Rev. A 1 of 58 UBoot, FPGA, Miniboot, BootROM, Upgrade Requirements Upgrading an OmniSwitch to 6.4.4.R01 UBoot, FPGA, Miniboot, BootROM, Upgrade Requirements The software versions listed below are the minimum required, except where otherwise noted. Switches running the minimum versions, as listed below, do not require any Uboot, Miniboot, or FPGA upgrades when upgrading to AOS 6.4.4.R01. Switches not running the minimum version required should upgrade to the latest Uboot, Miniboot, FPGA that is available with the 6.4.4.R01 AOS software available from Service & Support. OmniSwitch 9000E Release 6.4.4.R01 Miniboot.uboot CMM 6.4.3.479.R01 UBoot CMM 6.4.3.479.R01 UBoot NI 6.4.3.479.R01 FPGA CMM Major Revision: 2 Minor Revision: 25 (displays as 0x19; recommended) Note: The 'S01' build is required for ISSU support. Also note that Release 6.4.4.R01 is not supported on the OS 9600, 9700, or 9800. OmniSwitch 6850 Release 6.4.4.R01 Miniboot.uboot 6.4.3.479.R01 UBoot 6.4.3.479.R01 - (Minimum) 6.4.4.213.R01 - (Recommended for OS6850/OS6850E mixed stack) FPGA No minimum required Note. For more information on upgrading in a mixed stack environment (6850/6850E), see “OmniSwitch 6850” on page -32. OmniSwitch 6850E Release 6.4.4.R01 Miniboot.uboot 6.4.4.213.R01 UBoot 6.4.4.213.R01 CPLD No minimum required OmniSwitch 6855/OmniSwitch 6855-U24X Release 6.4.4.R01 Miniboot.uboot 6.4.3.479.R01 UBoot 6.4.3.479.R01 FPGA No minimum required 2 of 58 Upgrading an OmniSwitch to 6.4.4.R01, Part No. 032731-10 Rev. A Upgrading an OmniSwitch to 6.4.4.R01 UBoot, FPGA, Miniboot, BootROM, Upgrade Requirements OmniSwitch 6400 Release 6.4.4.R01 Miniboot 6.4.3.565.R01 UBoot 6.4.3.565.R01 FPGA OS6400-C24/P24 (v16) OS6400-C48/P48 (v11) OS6400-U24 (v10) Upgrading an OmniSwitch to 6.4.4.R01, Part No. 032731-10 Rev. A 3 of 58 OmniSwitch 9000E Upgrading an OmniSwitch to 6.4.4.R01 OmniSwitch 9000E Upgrading With WebView Upgrading OS9000E Series Switches to 6.4.4.R01 using WebView consists of the following steps. The steps must be performed in order. You must complete the Image File upgrade before upgrading the UBoot and Miniboot Files. 1 2 Upgrading the Image Files. Upgrading the U-Boot and Miniboot Files, if necessary. Note. Release 6.4.4.R01 is not supported on the OS 9600, 9700, or 9800. WARNING: You MUST complete the Image File upgrade BEFORE upgrading the U-Boot and Miniboot Files. Please verify that the switch has been properly upgraded to 6.4.4.R01 before upgrading the U-boot and Miniboot. Upgrading the Image Files Follow the steps below to upgrade the Image Files to 6.4.4.R01. 1 2 Download the 6.4.4.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC. Log into the switch through WebView. (In dual redundant configurations you must log into the primary CMM). Note. Before proceeding with the remaining steps, make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes). To view and change the setting, go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration. 3 4 Select System > System Mgmt > Install to locate and FTP the 6.4.4.R01 Image Files that you downloaded in Step 1. Click on the Browse button to locate the files. Select one of the files and click Open. All of the files will appear in the “Selected” area as shown below. 4 of 58 Upgrading an OmniSwitch to 6.4.4.R01, Part No. 032731-10 Rev. A Upgrading an OmniSwitch to 6.4.4.R01 OmniSwitch 9000E 5 Click on the Remove All button to move all of the files to the “Available” area; then select the following Image Files and click the Add button to move them back to the “Selected” area as shown below: Jadvrout.img, Jbase.img, Jencrypt.img, Jeni.img, Jos.img, Jsecu.img. Upgrading an OmniSwitch to 6.4.4.R01, Part No. 032731-10 Rev. A 5 of 58 log into WebView.R01 6 Transfer the files to the flash/working directory.4. In the “Install Images/Reload CMM” area. Select Physical > Chassis Mgmt > CMM > Management as shown below. Copy the files to the Certified Directory and sync the Primary and Secondary CMMs (if applicable). Reload the switch from the Working Directory. Click OK at the warning prompt. 032731-10 Rev. then click the Transfer button.4.R01. 7 8 9 6 of 58 Upgrading an OmniSwitch to 6. Wait until the process is complete (indicated in the area next to the Transfer button .4.OmniSwitch 9000E Upgrading an OmniSwitch to 6. then click the Reload button. Make sure the Destination Directory is flash/working. Wait until the process is complete.4. A . Part No. After the CMM finishes rebooting. select Working in the Reload CMM From field.“All files have been transferred successfully”). 4.Upgrading an OmniSwitch to 6.4.4.4.R01. 032731-10 Rev. or Copy Working -> Certified & Synchronize with Secondary for switches with a secondary CMM. Part No. select Copy Working -> Certified on Primary for switches with a single CMM. WARNING: DO NOT INTERRUPT the upgrade process until it is complete.R01 OmniSwitch 9000E 10 In the Software Configuration field. Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files.479. if necessary. Please verify that the switch has been properly upgraded to 6. The switch will copy the files from the Working to the Certified Directory and synchronize the CMMs (if applicable).4.R01 is required for the 6.4. Log into the switch through WebView. (In dual redundant configurations you must log into the primary CMM.R01 before upgrading the U-boot and Miniboot. A 7 of 58 .R01 upgrade. U-Boot and Miniboot version 6. Wait for the process to complete. then click Apply. Interruption of the process will result in an unrecoverable failure condition.4. 1 2 Download the applicable upgrade files from the Alcatel-Lucent Service and Support website to your PC.3. WARNING: You MUST complete the Image File upgrade BEFORE upgrading the U-Boot and Miniboot Files.4.4.) Upgrading an OmniSwitch to 6. 4.4.bin files and click the Add button to move them to the “Selected” area as shown below. 032731-10 Rev. A . Select one of the files and click Open.4. 3 4 Select System > System Mgmt > Install to locate and FTP the 6.4. 5 Click on the Remove All button to move all of the files to the “Available” area.R01. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes). Click on the Browse button to locate the files. To view and change the setting. then select both the miniboot. If you have not already done so.R01 Note. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration.R01 Image Files that you downloaded in Step 1.OmniSwitch 9000E Upgrading an OmniSwitch to 6.4.uboot and u-boot.4. All of the files will appear in the “Selected” area as shown below. Part No. 8 of 58 Upgrading an OmniSwitch to 6. R01. When the upgrade is complete. This will upgrade the Uboot and Miniboot Files on all of the CMMs and the NIs. STOP: If you have not already completed the Upgrade Image section. Part No.Upgrading an OmniSwitch to 6. After verifying that the upgrade was successful.uboot and uboot. select Working from the Reload CMM From field.4. Interruption of the process will result in an unrecoverable failure condition. click on Uboot-Miniboot. Make sure the Destination Directory is /flash. delete the miniboot. 8 Reload the switch from the Working Directory. 9 Upgrading an OmniSwitch to 6.bin files from the Flash Directory by selecting System > System Mgmt > File Management > Local. Wait until the process is complete (indicated in the area next to the Transfer button . Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade. the following message appears: “set operation finished successfully. as shown below. Wait until the process is complete. 032731-10 Rev.4. The upgrade progress is indicated in the upper right cornet of the screen.R01 OmniSwitch 9000E 6 Transfer the files to the /flash Directory. Click OK at the warning prompt.” WARNING: DO NOT INTERRUPT the upgrade process until it is complete. 7 In the “Update” area. then click the Reload button. DO NOT CONTINUE.4. In the “Install Images/Reload CMM” area. A 9 of 58 . then click the Transfer button.4.“All files have been transferred successfully”). then click OK at the confirmation prompt. Part No.R01 10 Check the box next to the miniboot.4. A . select Delete in the File Operations box.OmniSwitch 9000E Upgrading an OmniSwitch to 6.bin file. 10 of 58 Upgrading an OmniSwitch to 6.uboot file.4. Repeat to delete the u-boot. Verifying the Upgrade Verifying the Software Upgrade To verify that the software was successfully upgraded. go to the Loaded Image Files page by selecting System > System Mgmt > Images > Loaded Images as shown below.4. then click OK at the confirmation prompt.R01. 032731-10 Rev.4. R01.R01 OmniSwitch 9000E In addition.4. Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot Files were successfully upgraded on the CMM. A 11 of 58 . as shown below. 032731-10 Rev.Upgrading an OmniSwitch to 6.4. you should also select System > System Mgmt > Images > Images in Certified and System > System Mgmt > Images > Images in Working to verify that Certified and Working directories were successfully upgraded.4. Part No. go to the CMM Hardware Component Information page by selecting Physical > Chassis Mgmt > CMM > Hardware Component.4. Upgrading an OmniSwitch to 6. as shown below. A .4.4.R01.OmniSwitch 9000E Upgrading an OmniSwitch to 6.4.R01 To verify that the U-Boot file was successfully upgraded on the switch’s NIs. Part No. 12 of 58 Upgrading an OmniSwitch to 6. go to the Network Interfaces page by selecting Physical > Chassis Mgmt > Network Interfaces. 032731-10 Rev.4. Jsecu.4. 13 of 58 Upgrading an OmniSwitch to 6.img.R01. if necessary. FTP the following 6.Upgrading an OmniSwitch to 6.4.R01 OmniSwitch 9000E Upgrading With The CLI Upgrading OS9000E Series Switches to 6. WARNING: You MUST complete the Image File upgrade BEFORE upgrading the U-Boot and Miniboot Files.4.R01 using the CLI consists of the following steps. Jeni. You must complete the Image File upgrade before upgrading the U-Boot and Miniboot Files.4.4.4.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC.4. Jos.4. Jencrypt.4.4. Please verify that the switch has been properly upgraded to 6.R01. 1 2 Download the 6. Part No.4. 1 2 Upgrading the Image Files.img.R01 Image Files to the /flash/working directory of the primary CMM: Jadvrout. Upgrading the U-Boot and Miniboot Files. Upgrading the Image Files Follow the steps below to upgrade the Image Files to 6.img.img.4. 032731-10 Rev.R01 before upgrading the U-boot and Miniboot.img. Jbase.img. The steps must be performed in order.4. A .4. R01. Please verify that the switch has been properly upgraded to 6.R01 before upgrading the U-boot and Miniboot.R01 3 4 Log into the switch. STOP: If you have not already completed the Upgrade Image section.4. Part No. Reload the switch from the working directory. FTP the miniboot. A .1 14 of 58 Upgrading an OmniSwitch to 6. Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade.4.4.R01 is required for the 6. U-Boot and Miniboot version 6.4.4. DO NOT CONTINUE. WARNING: DO NOT INTERRUPT the upgrade process until it is complete.4.2. - If you have a single CMM switch enter: -> copy working certified - If you have redundant CMMs enter: -> copy working certified flash-synchro The switch will copy the files from the Working to the Certified Directory and synchronize the CMMs (if applicable). WARNING: You MUST complete the Image File upgrade BEFORE upgrading the U-Boot and Miniboot Files.R01 upgrade.4.66. 1 2 Download the applicable upgrade files from the Alcatel-Lucent Service and Support web site to your PC. In dual redundant configurations.3. Client Address 127.4.479.bin files to the /flash directory on the primary CMM. -> update uboot-miniboot Sample output for "update uboot-miniboot” -> WED APR 20 17:29:09 : SYSTEM (75) info message: +++ ---->SSACTION_UPDATE_UBOOT_MINIBOOT WED APR 20 17:29:09 : CSM-CHASSIS (103) info message: +++ == CSM == Update bootrom on all slots +++ == CSM == sysUpdate begin WED APR 20 17:29:10 : FTP (82) info message: +++ Session 0 New Connection.4. -> reload working no rollback-timeout 5 6 After the switch finishes rebooting. Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files. if necessary. you must log into the primary switch. 3 Execute the following CLI command to update the U-Boot and Miniboot Files on the switch. Interruption of the process will result in an unrecoverable failure condition.OmniSwitch 9000E Upgrading an OmniSwitch to 6. log into the switch. Wait for the process to complete. 032731-10 Rev. Copy the Image Files from the Working Directory to the Certified Directory.uboot and u-boot. bin! +++ Session 0 Ending WED APR 20 17:29:13 : SYSTEM (75) info message: +++ NI 1 software update started WED APR 20 17:29:20 : SYSTEM (75) info message: +++ NI 1 software update completed -.R01 6.4.4.4.4.4.4.4. A 15 of 58 . -> show microcode Package Release Size Description -----------------+---------------+--------+----------------------------------Jbase. See Verifying the Upgrade with the CLI below for information on verifying the upgrade.bin copied WED APR 20 17:29:26 : SYSTEM (75) info message: +++ NI 4 software update started WED APR 20 17:29:37 : SYSTEM (75) info message: +++ NI 4 software update completed -.R01 6.img Jos.4.file /flash/u-boot.4.342. Interruption of the process will result in an unrecoverable failure condition.R01 6.R01.4.img Jadvrout.4.img 6.session end ---+++ == CSM == UPDATE COMPLETED WARNING: DO NOT INTERRUPT the upgrade process until it is complete.R01 21798508 Alcatel-Lucent Base Software 2859888 Alcatel-Lucent Advanced Routing 2151785 Alcatel-Lucent OS 6497127 Alcatel-Lucent NI software 581967 Alcatel-Lucent Security Management 3437 Alcatel-Lucent Encryption Management Upgrading an OmniSwitch to 6. 032731-10 Rev. and the reload the switch from the working directory: -> reload working no rollback-timeout The upgrade is now complete. Part No.img Jsecu.342.342.4.R01.img Jencrypt.R01 OmniSwitch 9000E +++ Get /flash/u-boot.4.bin copied WED APR 20 17:30:44 : CSM-CHASSIS (103) info message: +++ == CSM == sysUpdate end +++ == CSM == timer_r:duplex---.4.4.4.4.342.R01 6.Upgrading an OmniSwitch to 6.file /flash/u-boot. delete the U-Boot and Miniboot Files from the /flash directory.4.342. Verifying the Upgrade with the CLI Verifying the Software Upgrade To verify that the software was successfully upgraded to 6. use the show microcode command as shown below.img Jeni.R01 6. 4 When the “UPDATE COMPLETED" message appears.342. A . G25Q0772. : 6. Part No. -> show hardware info CPU Type Flash Manufacturer Flash size RAM Manufacturer RAM size NVRAM Battery OK ? CPLD rev FPGA major rev FPGA minor rev uboot Version uboot-miniboot Version Backplane type : Motorola MPC8540 ADS. Motorola MPC8540 ADS. 51.4. : YES. 902367-90. : 0x00000040 . : 0x6.Physical 1: : OS9700-24. : 6.R01. BCM56504_A1.R01. UP. : Regular mode. JUN 28 2006. -> show ni Module in slot 1 Model Name: Description: Part Number: Hardware Revision: Serial Number: Manufacture Date: Firmware Version: Admin Status: Operational Status: Power Consumption: Power Control Checksum: CPU Model Type MAC Address: ASIC .R01.479. use the show hardware info command as shown below.4.Other.3. C15.4.479.OmniSwitch 9000E Upgrading an OmniSwitch to 6. use the show ni command as shown below. 16 of 58 Upgrading an OmniSwitch to 6. 00:d0:95:ec:d1:c8.4. : SanDisk SDCFJ-128 : 128319488 bytes (122 MB). : 0x2.4. : 268435456 bytes (256 MB).R01 Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot Files were successfully upgraded on the CMM. . To verify that the NI modules were successfully upgraded. 0xd872. 032731-10 Rev. C24 10/100/1000.4. POWER ON. : 0x19.4. . . Build not supported on the model.479.R01. Upgrading an OmniSwitch to 6.R01.4. contact Customer Support.4. Part No.Physical 1: UBOOT Version : UBOOT-miniboot Version : POE SW Version : : 0005/00. For more information. 0005/B9. No Miniboot. A 17 of 58 .Upgrading an OmniSwitch to 6. 6.Physical 1: FPGA .R01 OmniSwitch 9000E FPGA . n/a Upgrade/Downgrade Software Matrix Refer to the matrix below for software compatibility when upgrading/downgrading a 9000E Series Switch to/from Build 6. C13. N/A = Not applicable. UP.Physical 1: UBOOT Version : UBOOT-miniboot Version : POE SW Version : Module in slot 2 Model Name: Description: Part Number: Hardware Revision: Serial Number: Manufacture Date: Firmware Version: Admin Status: Operational Status: Power Consumption: Power Control Checksum: CPU Model Type MAC Address: ASIC . 55. I = Image Files F= U-Boot/Miniboot Yes = You can upgrade/downgrade to the next build. BCM56504_A1. Motorola MPC8540 ADS. U24 1000.4.R01. No Miniboot.4. POWER ON.479. G0410042.3.3.R01. 0xb156. n/a OS9700-U24. FEB 23 2006. 902370-10.4. 6. 032731-10 Rev.4. No = You cannot upgrade/downgrade to the next build. 00:d0:95:e1:6e:7a.4.4. R01 F = 6.4.4.4.R01.3.R01 Upgrade/Downgrade Matrix 6. when downgrading.4.R01 GA F = 6.R01 Build and Supported Software Versions For Each Upgrade 6.R01 GA I = 6. A .1. For example.4.4.4.479.149.OmniSwitch 9000E Upgrading an OmniSwitch to 6.4. 032731-10 Rev. the lowest software version that you can run on a 9000E Series Switch is 6.1.4.3 GA I = 6. contact Customer Support.4.R01 F = 6.2.3. Also.R01 I = 6.4.4.R01.3.4.2 GA 6.1.R01 Yes Yes Yes Model 9000E Note.1 GA 6.4. For more information.R01 F = 6.4.149.4.4. Part No.4. Hardware is only backward compatible down to the software that originally supported it. make sure to load the applicable U-Boot/Miniboot Files.4. 18 of 58 Upgrading an OmniSwitch to 6.479.R01 I = 6.1. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration. Part No.R01.4. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files.R01 before upgrading the U-boot and Miniboot. Upgrading the Image Files Follow the steps below to upgrade the image files to 6.4. 3 4 Select System > System Mgmt > Install to locate and FTP the 6. Upgrading the U-Boot and Miniboot Files. A 19 of 58 .4.4.R01 using WebView consists of the following steps. WARNING: If you are upgrading the U-boot and Miniboot.4.4. the steps must be performed in order. Upgrading an OmniSwitch to 6.4.4. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes). Before proceeding with the remaining steps.R01 image files that you downloaded in Step 1. 032731-10 Rev.4. 1 2 Download the 6. Log into the switch through WebView.4. if necessary.4.R01. as shown below.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC. All of the files will appear in the “Selected” area. You must complete the image file upgrade before upgrading the U-Boot and Miniboot files.4. To view and change the setting.4. Note. Please verify that the switch has been properly upgraded to 6. Click on the Browse button to locate the files. If you are performing a U-Boot/Miniboot upgrade.4. 1 2 Upgrading the Image Files.Upgrading an OmniSwitch to 6. Select one of the files and click Open.R01 OmniSwitch 6855 OmniSwitch 6855 Upgrading with WebView Upgrading OS6855 Series Switches to 6. Kbase.4.img. Part No.img. A . 032731-10 Rev.img. Kadvrout. Keni.R01 5 Click on the Remove All button to move all of the files to the “Available” area.img.OmniSwitch 6855 Upgrading an OmniSwitch to 6.4. Ksecu. then select the following image files and click the Add button to move them to the “Selected” area as shown below: K2Ios.img. 20 of 58 Upgrading an OmniSwitch to 6.img.4.4.R01. Kencrypt. Wait until the process is complete (indicated in the area next to the Transfer button .4.“All files have been transferred successfully”). In the “Install Images/Reload CMM” area. Click OK at the warning prompt.R01 OmniSwitch 6855 6 Transfer the files to the flash/working directory. log into WebView. 7 8 9 Upgrading an OmniSwitch to 6. select Working in the Reload CMM From field. then click the Transfer button.4.4. Make sure the Destination Directory is flash/working. Select Physical > Chassis Mgmt > CMM > Management as shown below. Reload the switch from the Working Directory. A 21 of 58 . then click the Reload button. Part No. Wait until the process is complete.R01. 032731-10 Rev. After the CMM finishes rebooting.Upgrading an OmniSwitch to 6.4. 22 of 58 Upgrading an OmniSwitch to 6. 032731-10 Rev. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files.4.R01 10 In the Software Management field. select Copy Working -> Certified & Synchronize with Secondary and click Apply. The switch will synchronize files from the working directory with all other stacks (if applicable).R01. Wait for the synchronization process to complete on all switches before proceeding to the next step. Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files.4. WARNING: If you are upgrading the U-boot and Miniboot. WARNING: DO NOT INTERRUPT the upgrade process until it is complete.4.3.479.4.R01 before upgrading the U-boot and Miniboot.4. U-Boot and Miniboot version 6. Interruption of the process will result in an unrecoverable failure condition. if necessary. Part No.R01 is required for the 6. A .4.4. select Copy Working -> Certified on Primary for standalone switches. Please verify that the switch has been properly upgraded to 6. For a stack.OmniSwitch 6855 Upgrading an OmniSwitch to 6.4.R01 upgrade.4. 4. A 23 of 58 . Log into the switch through WebView. If you have not already done so. All of the files will appear in the “Selected” area.R01 OmniSwitch 6855 1 2 Download the applicable U-Boot/Miniboot files from the Alcatel-Lucent Service and Support web site to your PC (ku-boot. Upgrading an OmniSwitch to 6. then select the kuboot.4.bin and k2Iminiboot.Upgrading an OmniSwitch to 6. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration. 5 Click on the Remove All button to move all of the files to the “Available” area. Part No.4. Click on the Browse button to locate the files.uboot).4. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes).4. To view and change the setting.uboot file and click the Add button to move them to the “Selected” area as shown below.bin file and the k2Iminiboot. Note.R01 image files that you downloaded in Step 1.4. 3 4 Select System > System Mgmt > Install to locate and FTP the 6. Select one of the files and click Open. as shown below. 032731-10 Rev.R01. 4.4. then click the Transfer button. 8 Reload the switch from the Working Directory. 24 of 58 Upgrading an OmniSwitch to 6. A . the following message appears “set operation finished successfully. 032731-10 Rev. Interruption of the process will result in an unrecoverable failure condition.R01 6 Make sure the Destination Directory is /flash. Wait until the process is complete. select Working from the Reload CMM From field. DO NOT CONTINUE.4. When the upgrade is complete. Click OK at the warning prompt.” WARNING: DO NOT INTERRUPT the upgrade process until it is complete. then click the Reload button. click on Uboot-Miniboot. Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade. then click OK at the confirmation prompt to upgrade the Uboot and Miniboot files.R01. STOP: If you have not already completed the Upgrade Image section. In the “Install Images/Reload CMM” area.4. Wait until the process is complete (indicated in the area next to the Transfer button . 7 In the “Update” area.“All files have been transferred successfully”). Part No. The upgrade progress is indicated in the upper right corner of the screen.OmniSwitch 6855 Upgrading an OmniSwitch to 6. then click OK at the confirmation prompt.uboot file.Upgrading an OmniSwitch to 6.uboot and ku-boot. select Delete in the File Operations box. as shown below. Part No. 10 Check the box next to the ku-boot.4. delete the K2Iminiboot. Repeat to delete the k2Iminiboot. Verifying the Upgrade Verifying the Software Upgrade To verify that the software was successfully upgraded. Upgrading an OmniSwitch to 6. 032731-10 Rev. go to the Loaded Image Files page by selecting System > System Mgmt > Images > Loaded Images as shown below. A 25 of 58 .4.R01 OmniSwitch 6855 9 After verifying that the upgrade was successful.R01.bin files from the Flash Directory by selecting System > System Mgmt > File Management > Local.4.bin file.4. R01.4.R01 In addition. Part No. 26 of 58 Upgrading an OmniSwitch to 6.4. go to the Network Interfaces page by selecting Physical > Chassis Mgmt > Network Interfaces. Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot files were successfully upgraded. Information for each switch in a stack (if applicable) is displayed.OmniSwitch 6855 Upgrading an OmniSwitch to 6. you should also select System > System Mgmt > Images > Images in Certified and System > System Mgmt > Images > Images in Working to verify that Certified and Working directories were successfully upgraded. as shown below. A .4. 032731-10 Rev.4. Scroll right to the Uboot Version and Miniboot Version columns for the switch(es). 4.4. Part No. 1 2 Download the 6. You must complete the image file upgrade before upgrading the U-Boot and Miniboot files.4. Please verify that the switch has been properly upgraded to 6.img.4.4.R01 using the CLI consists of the following steps. the steps must be performed in order. 1 2 Upgrading the Image Files. FTP the following 6.4.img.img.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC.4.R01 OmniSwitch 6855 Upgrading with the CLI Upgrading OS6855 Series Switches to 6. WARNING: If you are upgrading the U-boot and Miniboot.4. If you are performing a U-Boot/Miniboot upgrade. A 27 of 58 . Ksecu.ing.4.4. if necessary.img.4. Keni.R01.R01.R01 image files to the /flash/working directory of the primary switch: K2Ios.Upgrading an OmniSwitch to 6.4. Kencrypt. Upgrading an OmniSwitch to 6. Upgrading the Image Files Follow the steps below to upgrade the image files to 6. Upgrading the U-Boot and Miniboot Files.4.4.img. 032731-10 Rev. Kadvrout. Kbase.R01 before upgrading the U-boot and Miniboot. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files. 3 Execute the following CLI commands to update the Miniboot and U-Boot files on the switch(es) (can be a standalone or stack). Interruption of the process will result in an unrecoverable failure condition.R01 upgrade. 1 2 Download the applicable U-Boot/Miniboot files from the Alcatel-Lucent Service and Support web site to your PC (ku-boot.4.4. if necessary.4. FTP the ku-boot.uboot files to the /flash directory on the primary switch. Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files.bin and k2Iminiboot. U-Boot and Miniboot version 6.4. DO NOT CONTINUE. Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade. In dual redundant configurations you must log into the primary switch. Copy the image files from the Working Directory to the Certified Directory. log into the switch.. Reload the switch from the working directory.R01 is required for the 6. -> reload working no rollback-timeout 5 6 After the switch finishes rebooting.R01 3 4 Log into the switch.R01 before upgrading the U-boot and Miniboot. WARNING: DO NOT INTERRUPT the upgrade process until it is complete. A .OmniSwitch 6855 Upgrading an OmniSwitch to 6. Wait for the process to complete. 28 of 58 Upgrading an OmniSwitch to 6. WARNING: If you are upgrading the U-boot and Miniboot. - If you have a standalone switch enter: -> copy working certified - If you have a stack enter: -> copy working certified flash-synchro The switch will copy the files from the Working to the Certified Directory and synchronize the CMMs (if applicable). STOP: If you have not already completed the Upgrade Image section.3.4. 032731-10 Rev.4.bin and k2Iminiboot. -> update uboot-miniboot WED APR 20 14:19:34 : SYSTEM (75) info message: +++ ---->SSACTION_UPDATE_UBOOT_MINIBOOT WED APR 20 14:19:34 : CSM-CHASSIS (103) info message: +++ == CSM == Application & Watchdog Monitoring Stopped +++ == CSM == Update bootrom on all slots +++ == CSM == sysUpdate begin Allocating temporary buffer for bootrom image.479.uboot).R01. Please verify that the switch has been properly upgraded to 6.4.4. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files.. Part No.4. .. Interruption of the process will result in an unrecoverable failure condition.. See Verifying the Upgrade with the CLI..4.R01 OmniSwitch 6855 Reading bootrom image into temporary buffer.Upgrading an OmniSwitch to 6. 4 When the “UPDATE COMPLETED" message appears. A 29 of 58 ..4. below. Part No... Writing 131072 bytes at 0xff900000 Writing 131072 bytes at 0xff920000 Writing 131072 bytes at 0xff940000 Writing 131072 bytes at 0xff960000 Writing 131072 bytes at 0xff980000 Writing 131072 bytes at 0xff9a0000 Writing 42177 bytes at 0xff9c0000 Verifying miniboot sectors of flash. Writing bootrom to boot sectors of flash.. the reload the switch: -> reload working no rollback-timeout The upgrade is now complete...4. Default miniboot updated!!! sysStartWatchdog() Starting watchdog timer to INTERRUPT after 60 secs. WED APR 20 14:19:51 : CSM-CHASSIS (103) info message: +++ == CSM == timer_r:simplex---. Reading miniboot image into temporary buffer.session end ---+++ == CSM == UPDATE COMPLETED +++ == CSM == Application & Watchdog Monitoring Started WARNING: DO NOT INTERRUPT the upgrade process until it is complete.4.... 032731-10 Rev. Writing size 131072 bytes at 0xfff00000 Writing size 96740 bytes at 0xfff20000 Verifying bootrom sectors of flash. Writing miniboot(828609 bytes) to boot sectors of flash.. Bootrom updated!!! Allocating temporary buffer for checksuming miniboot image. delete the miniboot and u-boot files from the / flash directory. Upgrading an OmniSwitch to 6. for information on verifying the upgrade.R01. 4.R01 6. Freescale MPC8247 ADS.R01 Verifying the Upgrade with the CLI Verifying the Software Upgrade To verify that the software was successfully upgraded to 6. Part No. use the show ni command as shown below.342.R01 6.OmniSwitch 6855 Upgrading an OmniSwitch to 6. UP.4.342. FED 23 2009. 032731-10 Rev. 0.img Kencrypt.4. Mode of 10G ports at next boot:stacking.img 6.4.R01 6. use the show microcode command as shown below.4.342.4.4. A04.img K2Ios.4. 24 SFP+2 RJ45+10G.4. A .4.img Keni.4.R01 6. -> show ni Module in slot 1 Model Name: Description: Current mode of 10G ports: OS6855-U24X. The display below shows a successful image file upgrade.R01 6.img Kadvrout. K07Q0210.4.4.342. -> show microcode Package Release Size Description -----------------+---------------+--------+----------------------------------Kbase. . 0x8814.4.342.R01. Information for each switch in a stack (if applicable) is displayed.R01 17126563 Alcatel-Lucent Base Software 2810182 Alcatel-Lucent Advanced Routing 1773242 Alcatel-Lucent OS 5604309 Alcatel-Lucent NI software 606113 Alcatel-Lucent Security Management 3437 Alcatel-Lucent Encryption Management Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot files were successfully upgraded. stacking.R01. POWER ON. 30 of 58 Upgrading an OmniSwitch to 6.342.4.4. Part Number: Hardware Revision: Serial Number: Manufacture Date: Firmware Version: Admin Status: Operational Status: Power Consumption: Power Control Checksum: CPU Model Type : 902757-90.img Ksecu.4.4. 4.479. For example.4.4. n/a Upgrade/Downgrade Software Matrix Refer to the matrix below for software compatibility when upgrading/downgrading a 6855 Series Switch to/from Build 6. contact Customer Support.4.Physical 1: FPGA .4.R01 I = 6. Hardware is only backward compatible down to the software that originally supported it.4. contact Customer Support.2.479.265.R01 Build and Supported Software Versions For Each Upgrade 6.4.3.R01 GA I = 6.4.2.R01 GA F = 6. BCM56512_A0.R01 I = 6.86. 2.2.316.R01 F = 6. 032731-10 Rev.R01. 6.4.3.3.2 GA 6.4.3.4.R01 I = 6. For more information.3.R01 OmniSwitch 6855 MAC Address: ASIC .R01 F = 6.3.R01 F = 6.2. Upgrade/Downgrade Matrix 6.R01.3. the lowest software version that you can run on a 6855 Series Switch is 6. Part No.4. A 31 of 58 .2.R01 Yes Yes Yes Yes Model 6855 Note. when downgrading.Upgrading an OmniSwitch to 6.3.265.4.R01 F = 6.479.4.3.R01. N/A = Not applicable.3 GA I = 6.2. 6. No = You cannot upgrade/downgrade to the next build.R01. make sure to load the applicable U-Boot/Miniboot files.4 GA 6.4.4.R01.4.3.2 GA 6. Also.4. I = Image Files F = U-Boot/Miniboot Yes = You can upgrade/downgrade to the next build. Upgrading an OmniSwitch to 6.4.Physical 1: UBOOT Version : UBOOT-miniboot Version : POE SW Version : 00:e0:b1:b6:7d:f7.4.3.3. For more information.4. 4.4.R01 image files that you downloaded in Step 1. 32 of 58 Upgrading an OmniSwitch to 6.4. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files. as shown below. Upgrading the U-Boot and Miniboot Files. If you are performing a U-Boot/Miniboot upgrade. (In dual redundant configurations you must log into the primary switch). Click on the Browse button to locate the files.4. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration. it’s recommended that the OS6850 switches be upgraded to U-Boot/Miniboot version 6. 3 4 Select System > System Mgmt > Install to locate and FTP the 6.4.4. You must complete the image file upgrade before upgrading the U-Boot and Miniboot files.R01 OmniSwitch 6850 Upgrading with WebView Upgrading OS6850 Series Switches to 6. 032731-10 Rev. Before proceeding with the remaining steps. All of the files will appear in the “Selected” area. which is not compatible between models.213. This will cause all stack elements to use the FPGA version of the Primary device.4.4. Select one of the files and click Open.4.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC. Additionally. A . if necessary. Log into the switch through WebView. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes). WARNING: In a mixed OS6850/OS6850E stack environment never attempt an FPGA upgrade for all devices at the same time by using the 'all' parameter of the 'update' command. do not attempt to upgrade the miniboot/uboot for all elements at the same time by using the 'all' parameter of the 'update' command unless the Primary OS6850 miniboot/uboot has been upgraded to 6.4. Note.R01.4. WARNING: If you intend to run in a mixed OS6850/OS6850E stacked evironment you must first upgrade the existing OS6850 switches before adding the OS6850E to the stack.4. the steps must be performed in order.213.4. Part No. 1 2 Download the 6.4. WARNING: If you are upgrading the U-boot and Miniboot.R01 which is the minimum supported on the OS6850E switches. To view and change the setting. WARNING: In a mixed OS6850/OS6850E stack environment with an OS6850 as the primary element.OmniSwitch 6850 Upgrading an OmniSwitch to 6. 1 2 Upgrading the Image Files.4.4.R01 consists of the following steps. Upgrading the Image Files Follow the steps below to upgrade the image files to 6.R01.R01 to match the OS6850E switches.4.R01 before upgrading the U-boot and Miniboot.4. Please verify that the switch has been properly upgraded to 6. 032731-10 Rev.img. Kbase.Upgrading an OmniSwitch to 6.4.R01 OmniSwitch 6850 5 Click on the Remove All button to move all of the files to the “Available” area. A 33 of 58 . then select the following image files and click the Add button to move them to the “Selected” area as shown below: K2os. Kadvrout. Keni.4. Part No.4.img.img. Ksecu.img.R01.img. Kencrypt.img.4. Upgrading an OmniSwitch to 6. Click OK at the warning prompt. then click the Transfer button. Wait until the process is complete.R01. Select Physical > Chassis Mgmt > CMM > Management as shown below. Reload the switch from the Working Directory.4.R01 6 Transfer the files to the flash/working directory.4.OmniSwitch 6850 Upgrading an OmniSwitch to 6.4. After the CMM finishes rebooting. Wait until the process is complete (indicated in the area next to the Transfer button . log into WebView. A . 032731-10 Rev. select Working in the Reload CMM From field. then click the Reload button. Make sure the Destination Directory is flash/working. 7 8 9 34 of 58 Upgrading an OmniSwitch to 6.“All files have been transferred successfully”). Part No. In the “Install Images/Reload CMM” area.4. A 35 of 58 . The switch will synchronize files from the working directory with all other stacks (if applicable). select Copy Working -> Certified on Primary for standalone switches.R01 OmniSwitch 6850 10 In the Software Management field. select Copy Working -> Certified & Synchronize with Secondary and click Apply. Part No. 032731-10 Rev. WARNING: DO NOT INTERRUPT the upgrade process until it is complete.4. Upgrading an OmniSwitch to 6.4.R01.4. Wait for the synchronization process to complete on all switches before proceeding to the next step.4. Interruption of the process will result in an unrecoverable failure condition. For a stack.Upgrading an OmniSwitch to 6. 4.R01.4.R01 to match the OS6850E switches. Note. WARNING: In a mixed OS6850/OS6850E stack environment with an OS6850 as the primary element. as shown below.4. 032731-10 Rev. All of the files will appear in the “Selected” area. Part No.R01 is recommended in a mixed OS6850/OS6850E stacked environment. Additionally. WARNING: If you are upgrading the U-boot and Miniboot.4.479.R01 is required for the 6.R01 before upgrading the U-boot and Miniboot.4.4. 36 of 58 Upgrading an OmniSwitch to 6. WARNING: If you intend to run in a mixed OS6850/OS6850E stacked evironment you must first upgrade the existing OS6850 switches before adding the 6850E to the stack. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes).4. A . Click on the Browse button to locate the files.213.R01 Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files. If you have not already done so.4. Please verify that the switch has been properly upgraded to 6.4. 1 2 Download the applicable upgrade files from the Alcatel-Lucent Service and Support web site to your PC.4. do not attempt to upgrade the miniboot/uboot for all elements at the same time by using the 'all' parameter of the 'update' command unless the Primary OS6850 miniboot/uboot has been upgraded to 6. To view and change the setting.4.4. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration. Select one of the files and click Open. U-Boot and Miniboot version 6. WARNING: In a mixed OS6850/OS6850E stack environment never attempt an FPGA upgrade for all devices at the same time by using the 'all' parameter of the 'update' command.R01 upgrade and version 6.4.R01 which is the minimum supported on the OS6850E switches.4. it’s recommended that the OS6850 switches be upgraded to U-Boot/Miniboot version 6.213.4. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files.4. 3 4 Select System > System Mgmt > Install to locate and FTP the 6. if necessary. (In dual redundant configurations you must log into the primary switch).OmniSwitch 6850 Upgrading an OmniSwitch to 6.4. This will cause all stack devices to use the FPGA version of the Primary device.213.R01 image files that you downloaded in Step 1. which is not compatible with both models. Log into the switch through WebView.3. 4. Part No.bin file and the kminiboot. then select the kuboot.4.Upgrading an OmniSwitch to 6.uboot file and click the Add button to move them to the “Selected” Upgrading an OmniSwitch to 6.4.4.R01. 032731-10 Rev. A 37 of 58 .R01 OmniSwitch 6850 5 Click on the Remove All button to move all of the files to the “Available” area. then click OK at the confirmation prompt.OmniSwitch 6850 Upgrading an OmniSwitch to 6. DO NOT CONTINUE. Part No. The upgrade progress is indicated in the upper right corner of the screen.R01. A . select Working from the Reload CMM From field. 032731-10 Rev. When the upgrade is complete.“All files have been transferred successfully”). Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade. STOP: If you have not already completed the Upgrade Image section. then click the Transfer button. 38 of 58 Upgrading an OmniSwitch to 6. the following message appears “set operation finished successfully. 6 Make sure the Destination Directory is /flash. Click OK at the warning prompt. click on Uboot-Miniboot.4. 8 Reload the switch from the Working Directory. Wait until the process is complete (indicated in the area next to the Transfer button .4. then click the Reload button.R01 area as shown below. In the “Install Images/Reload CMM” area. Wait until the process is complete.” WARNING: DO NOT INTERRUPT the upgrade process until it is complete. select the slot number of the switch you want to update (or select “All” to update all switches in the stack).4.4. 7 In the “Update on slot” area. Interruption of the process will result in an unrecoverable failure condition. Upgrading an OmniSwitch to 6. select Delete in the File Operations box. Upgrading an OmniSwitch to 6. Repeat to delete the kminiboot.R01. Part No.uboot file.bin file. delete the miniboot.uboot and ku-boot. 032731-10 Rev.4.4. 10 Check the box next to the ku-boot.R01 OmniSwitch 6850 9 After verifying that the upgrade was successful. Verifying the Upgrade with WebView Verifying the Software Upgrade To verify that the software was successfully upgraded. as shown below.bin files from the Flash Directory by selecting System > System Mgmt > File Management > Local.4. go to the Loaded Image Files page by selecting System > System Mgmt > Images > Loaded Images as shown below. then click OK at the confirmation prompt. A 39 of 58 .4. A . 032731-10 Rev.4. go to the Network Interfaces page by selecting Physical > Chassis Mgmt > Network Interfaces.4.OmniSwitch 6850 Upgrading an OmniSwitch to 6.R01 In addition. 40 of 58 Upgrading an OmniSwitch to 6.4. Information for each switch in a stack (if applicable) is displayed. Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot files were successfully upgraded. you should also select System > System Mgmt > Images > Images in Certified and System > System Mgmt > Images > Images in Working to verify that Certified and Working directories were successfully upgraded.R01. Part No. as shown below.4. Scroll right to the Uboot Version and Miniboot Version columns for the switch(es). R01 OmniSwitch 6850 Upgrading with the CLI Upgrading OS6850 Series Switches to 6. A 41 of 58 . WARNING: If you are upgrading the U-boot and Miniboot. do not attempt to upgrade the miniboot/uboot for all elements at the same time by using the 'all' parameter of the 'update' command unless the Primary OS6850 miniboot/uboot has been upgraded to 6. it’s recommended that the OS6850 switches be upgraded to U-Boot/Miniboot version 6. 032731-10 Rev.4.4.4. Upgrading an OmniSwitch to 6.4.4. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files.4.4. Additionally. if necessary. 1 2 Upgrading the Image Files.213 to match the OS6850E switches. Upgrading the U-Boot and Miniboot Files. WARNING: If you intend to run in a mixed OS6850/OS6850E stacked evironment you must first upgrade the existing OS6850 switches before adding the 6850E to the stack. WARNING: In a mixed OS6850/OS6850E stack environment with an OS6850 as the primary element.Upgrading an OmniSwitch to 6. Part No.R01 consists of the following steps.R01 before upgrading the U-boot and Miniboot. If you are performing a U-Boot/Miniboot upgrade. the steps must be performed in order.4.4.4. Please verify that the switch has been properly upgraded to 6. You must complete the image file upgrade before upgrading the U-Boot and Miniboot files.4.R01.213 which is the minimum supported on the OS6850E switches.4. Upgrading the Image Files Follow the steps below to upgrade the image files to 6.213 which is the minimum supported on the OS6850E switches.img. WARNING: In a mixed OS6850/OS6850E stack environment with an OS6850 as the primary element.4. 42 of 58 Upgrading an OmniSwitch to 6.4.R01.4. Kadvrout. log into the switch. Part No. A .4. you MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files. 1 2 3 4 Download the 6. FTP the following 6. This will cause all stack devices to use the FPGA version of the Primary device.213.4.4.4.213 to match the OS6850E switches. WARNING: If you are upgrading the U-boot and Miniboot.R01 image files to the /flash/working directory of the primary switch: K2os. Keni. Copy the image files from the Working Directory to the Certified Directory. 032731-10 Rev.479. Additionally.4. U-Boot and Miniboot version 6.4. Kencrypt.4.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC.OmniSwitch 6850 Upgrading an OmniSwitch to 6.4. it’s recommended that the OS6850 switches be upgraded to U-Boot/Miniboot version 6. Reload the switch from the working directory.img.4.4.img. do not attempt to upgrade the miniboot/uboot for all elements at the same time by using the 'all' parameter of the 'update' command unless the Primary OS6850 miniboot/uboot has been upgraded to 6.R01 WARNING: In a mixed OS6850/OS6850E stack environment never attempt an FPGA upgrade for all devices at the same time by using the 'all' parameter of the 'update' command.R01 is recommended in a mixed OS6850/OS6850E stacked environment.4. WARNING: If you intend to run in a mixed OS6850/OS6850E stacked evironment you must first upgrade the existing OS6850 switches before adding the 6850E to the stack. Please verify that the switch has been properly upgraded to 6.4.4.R01. which is not compatible with both models. Interruption of the process will result in an unrecoverable failure condition Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files.img.4.R01 upgrade and version 6.4. -> reload working no rollback-timeout 5 6 After the switch finishes rebooting.4.R01 before upgrading the U-boot and Miniboot.4. Wait for the process to complete.img.3.R01 is required for the 6. Log into the switch. WARNING: DO NOT INTERRUPT the upgrade process until it is complete. Kbase. Ksecu.img. if necessary.4. In dual redundant configurations you must log into the primary switch. - If you have a standalone switch enter: -> copy working certified - If you have a stack enter: -> copy working certified flash-synchro The switch will copy the files from the Working to the Certified Directory and synchronize the CMMs (if applicable). 4.uboot copied +++ NI 2 software update started WED APR 20 10:59:19 : SYSTEM (75) info message: +++ NI 2 software update completed -.uboot files to the /flash directory on the primary switch.bin and kminiboot.R01...4. Writing flash. 032731-10 Rev. A 43 of 58 .. Done WED APR 20 10:59:14 : SYSTEM (75) info message: +++ NI 1 software update completed -.4. which is not compatible with both models. Writing flash... Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade... 1 2 Download the applicable upgrade files from the Alcatel-Lucent Service and Support web site to your PC.Upgrading an OmniSwitch to 6. FTP the ku-boot.file /flash/ku-boot.. STOP: If you have not already completed the Upgrade Image section. 3 Execute the following CLI command to update the Miniboot and U-Boot files on the switch(es) (can be a standalone or stack). Part No.file /flash/kminiboot. Done WED APR 20 10:58:59 : SYSTEM (75) info message: +++ NI 1 software update completed -. -> update uboot-miniboot Sample output for "update uboot-miniboot" for a stack of 2 WED APR 20 10:58:52 : SYSTEM (75) info message: +++ ---->SSACTION_UPDATE_UBOOT_MINIBOOT WED APR 20 10:58:52 : CSM-CHASSIS (103) info message: +++ == CSM == Update bootrom on all slots +++ == CSM == sysUpdate begin WED APR 20 10:58:54 : SYSTEM (75) info message: +++ NI 1 software update started Erasing flash..bin copied +++ NI 1 software update started Erasing flash... This will cause all stack devices to use the FPGA version of the Primary device.file /flash/ku-boot..4. DO NOT CONTINUE.bin copied Upgrading an OmniSwitch to 6.R01 OmniSwitch 6850 WARNING: In a mixed OS6850/OS6850E stack environment never attempt an FPGA upgrade for all devices at the same time by using the 'all' parameter of the 'update' command. Verifying the Upgrade with the CLI Verifying the Software Upgrade To verify that the software was successfully upgraded to 6.4.4.4.R01 6.342.R01 WED APR 20 11:01:23 : CSM-CHASSIS (103) info message: +++ == CSM == sysUpdate end +++ == CSM == timer_r:simplex---.342. delete the miniboot and u-boot files from the / flash directory. the reload the switch: -> reload working no rollback-timeout The upgrade is now complete.R01 6.img Kadvrout.4. 44 of 58 Upgrading an OmniSwitch to 6.R01 6.342.img Keni.R01.4.342. -> show ni Module in slot 1 Model Name: Description: Part Number: Hardware Revision: Serial Number: Manufacture Date: OS6850-P48.R01.4.img Ksecu. 4 When the “UPDATE COMPLETED" message appears.img Kencrypt.4.4.4.4.342. Information for each switch in a stack (if applicable) is displayed.4. 48 G POE.R01 17129458 Alcatel-Lucent Base Software 2810592 Alcatel-Lucent Advanced Routing 1744629 Alcatel-Lucent OS 5604310 Alcatel-Lucent NI software 606099 Alcatel-Lucent Security Management 3437 Alcatel-Lucent Encryption Management Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot files were successfully upgraded.342. 032731-10 Rev.OmniSwitch 6850 Upgrading an OmniSwitch to 6.session end ---+++ == CSM == UPDATE COMPLETED WARNING: DO NOT INTERRUPT the upgrade process until it is complete.4. 04.R01 6. 902463-10. The display below shows a successful image file upgrade. -> show microcode Package Release Size Description -----------------+---------------+--------+----------------------------------Kbase.4.4.4. use the show ni command as shown below.4. FEB 21 2006.4.4. G0650243. use the show microcode command as shown below. A .img 6. Interruption of the process will result in an unrecoverable failure condition. Part No.R01 6.img K2os. when downgrading.3.4.4. 6.479.4.R01.1.2. Part No. No = You cannot upgrade/downgrade to the next build. Upgrading an OmniSwitch to 6.Physical 2: FPGA .g. 6.Physical 1: ASIC .R01.R01.479. POWER ON. 0018/00.4.R01 for the 6850). BCM56504_B2.R01. contact Customer Support. Motorola MPC8248.4. n/a Upgrade/Downgrade Software Matrix Refer to the matrix below for software compatibility when upgrading/downgrading a 6850 Series Switch to/from Build 6.4. UP. A 45 of 58 .Upgrading an OmniSwitch to 6. Hardware is only backward compatible down to the software that originally supported it (e. BCM56502_B2.. For more information.4.R01 OmniSwitch 6850 Firmware Version: Admin Status: Operational Status: Power Consumption: Power Control Checksum: CPU Model Type MAC Address: ASIC . 0x23a5. 95. 032731-10 Rev. N/A = Not applicable. contact Customer Support. Note. 00:d0:95:e2:6d:24. make sure to load the applicable U-Boot/Miniboot files.Physical 1: UBOOT Version : UBOOT-miniboot Version : POE SW Version : : . 6. Also. For more information.3.4. I = Image Files F = U-Boot/Miniboot Yes = You can upgrade/downgrade to the next build. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes).4.4. as shown below. WARNING: The steps MUST be performed in order. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration.4. Part No.4. If you are performing a U-Boot/Miniboot upgrade. Select one of the files and click Open. Before proceeding with the remaining steps.R01 consists of the following steps. All of the files will appear in the “Selected” area.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC. You must complete the image file upgrade first. the FPGA upgrade. 032731-10 Rev.R01 image files that you downloaded in Step 1.4. You must complete the image file upgrade before upgrading the U-Boot and Miniboot files. if applicable. and finally. Upgrading the FPGA (OS6400-C24 and OS6400-P24 models only). Note. 46 of 58 Upgrading an OmniSwitch to 6.OmniSwitch 6400 Upgrading an OmniSwitch to 6.4. the steps must be performed in order.4. Log into the switch through WebView. To view and change the setting.R01 OmniSwitch 6400 Upgrading with WebView Upgrading OS6400 Series Switches to 6. Click on the Browse button to locate the files.4. 1 2 Download the 6. followed by the U-Boot/Miniboot upgrade. 1 2 3 Upgrading the Image Files.4. A .R01. Upgrading the Image Files Follow the steps below to upgrade the image files to 6.4. Upgrading the U-Boot and Miniboot Files.R01. 3 4 Select System > System Mgmt > Install to locate and FTP the 6.4.4. 4. Gos.4. A 47 of 58 . Gsecu.R01.R01 OmniSwitch 6400 5 Click on the Remove All button to move all of the files to the “Available” area. Geni.4.img.4. Upgrading an OmniSwitch to 6. 032731-10 Rev. then select the following image files and click the Add button to move them to the “Selected” area as shown below: Gbase.img. Part No.img.Upgrading an OmniSwitch to 6.img. then click the Transfer button. Wait until the process is complete. Reload the switch from the Working Directory. 032731-10 Rev. Part No.4. After the CMM finishes rebooting. Wait until the process is complete (indicated in the area next to the Transfer button . Select Physical > Chassis Mgmt > CMM > Management as shown below. Make sure the Destination Directory is flash/working.4. In the “Install Images/Reload CMM” area. select Working in the Reload CMM From field.R01. then click the Reload button. log into WebView. 7 8 9 48 of 58 Upgrading an OmniSwitch to 6.4. A .“All files have been transferred successfully”).R01 6 Transfer the files to the flash/working directory.OmniSwitch 6400 Upgrading an OmniSwitch to 6.4. Click OK at the warning prompt. R01 before upgrading the U-boot and Miniboot files.4.565.4. WARNING: DO NOT INTERRUPT the upgrade process until it is complete.4. select Copy Working -> Certified on Primary for standalone switches.4.4.4. For a stack.Upgrading an OmniSwitch to 6.R01. select Copy Working -> Certified & Synchronize with Secondary and click Apply. Part No. 1 Download the applicable upgrade files from the Alcatel-Lucent Service and Support web site to your PC. The switch will synchronize files from the working directory with all other stacks (if applicable). Wait for the synchronization process to complete on all switches before proceeding to the next step. Please verify that the switch has been properly upgraded to 6. WARNING: You MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files.3. Upgrading an OmniSwitch to 6. Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files.R01 upgrade. U-Boot and Miniboot version 6. Interruption of the process will result in an unrecoverable failure condition.4.R01 is required for the 6. 032731-10 Rev.R01 OmniSwitch 6400 10 In the Software Management field.4. A 49 of 58 .4. go to the Session Type Parameters page by selecting Security > ASA > Sessions > Configuration. 032731-10 Rev. To view and change the setting.OmniSwitch 6400 Upgrading an OmniSwitch to 6.4.4. make sure that the switch’s Web Management Inactivity Timer is set to at least 10 minutes (default setting is 4 minutes). All of the files will appear in the “Selected” area. A . 5 Click on the Remove All button to move all of the files to the “Available” area.4.R01.bin file and click the Add button to move them to the “Selected” area as shown below. Select one of the files and click Open. If you have not already done so. Note.4. then select the gminiboot. as shown below.4.R01 2 Log into the switch through WebView.R01 image files that you downloaded in Step 1. Part No.4. 3 4 Select System > System Mgmt > Install to locate and FTP the 6.uboot file and the ku-boot. 50 of 58 Upgrading an OmniSwitch to 6. Click on the Browse button to locate the files. DO NOT CONTINUE.R01 OmniSwitch 6400 6 Make sure the Destination Directory is /flash.4. Wait until the process is complete. When the upgrade is complete. then click OK at the confirmation prompt. Click OK at the warning prompt.4. A 51 of 58 . In the “Install Images/Reload CMM” area. click on Uboot-Miniboot.” WARNING: DO NOT INTERRUPT the upgrade process until it is complete. The upgrade progress is indicated in the upper right corner of the screen. Wait until the process is complete (indicated in the area next to the Transfer button . STOP: If you have not already completed the Upgrade Image section. 7 In the “Update” area. the following message appears “set operation finished successfully. select Working from the Reload CMM From field.R01. Interruption of the process will result in an unrecoverable failure condition. then click the Transfer button. 8 Reload the switch from the Working Directory.“All files have been transferred successfully”).4. Part No.4. then click the Reload button. Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade. Upgrading an OmniSwitch to 6. 032731-10 Rev.Upgrading an OmniSwitch to 6. This will upgrade the Uboot and Miniboot files on all of the switches in the stack. as shown below. Upgrading the U-Boot and Miniboot Files. the steps must be performed in order. 10 Check the box next to the ku-boot. You must complete the image file upgrade before upgrading the U-Boot and Miniboot files. delete the miniboot. Part No.4.bin files from the Flash Directory by selecting System > System Mgmt > File Management > Local. Repeat to delete the kminiboot. 032731-10 Rev. A . select Delete in the File Operations box.4.uboot file. Upgrading with the CLI Upgrading OS6400 Series Switches to 6. then click OK at the confirmation prompt.R01. Upgrading the FPGA The FPGA cannot be upgraded on the OS6400 using WebView.4. Refer to the CLI instructions “Upgrading the FPGA” on page -55.4.R01 consists of the following steps. If you are performing a U-Boot/Miniboot upgrade.R01 9 After verifying that the upgrade was successful.uboot and ku-boot. 1 2 Upgrading the Image Files. 52 of 58 Upgrading an OmniSwitch to 6.OmniSwitch 6400 Upgrading an OmniSwitch to 6.bin file.4.4. 032731-10 Rev. -> reload working no rollback-timeout 4 5 After the switch finishes rebooting. WARNING: The steps MUST be performed in order.4. Gos. Copy the image files from the Working Directory to the Certified Directory.R01 image files to the /flash/working directory: Gbase.uboot and ku-boot. -> update uboot-miniboot Upgrading an OmniSwitch to 6.R01 upgrade.4. U-Boot and Miniboot version 6. and finally. 3 Execute the following CLI commands to update the Miniboot and U-Boot files on the switch(es) (can be a standalone or stack). FTP the following 6. DO NOT CONTINUE. A 53 of 58 . STOP: If you have not already completed the Upgrade Image section. Log into the switch and reload the switch from the working directory.4.img. Gsecu.4..4. the FPGA upgrade. Upgrading the U-Boot and Miniboot Files Follow the steps below to upgrade the U-Boot and Miniboot Files. Interruption of the process will result in an unrecoverable failure condition. Wait for the process to complete. - If you have a standalone switch enter: -> copy working certified - If you have a stack enter: -> copy working certified flash-synchro The switch will copy the files from the Working to the Certified Directory and synchronize the CMMs (if applicable). followed by the U-Boot/Miniboot upgrade. FTP the gminiboot. if applicable. log into the switch.4.R01 is required for the 6.Upgrading an OmniSwitch to 6.4.img.R01 OmniSwitch 6400 3 Upgrading the FPGA (OS6400-C24 and OS6400-P24 models only).img. Part No.bin files to the /flash directory.R01 before upgrading the U-boot and Miniboot files. Please verify that the switch has been properly upgraded to 6. Complete the Image File upgrade before returning to this section to complete the Uboot/Miniboot upgrade. 1 2 Download the applicable upgrade files from the Alcatel-Lucent Service and Support web site to your PC. Upgrading the Image Files Follow the steps below to upgrade the image files to 6.4.4.img. You must complete the image file upgrade first.4.R01.4.565.R01 upgrade files from the Alcatel-Lucent Service and Support web site to your PC.4.3.4. WARNING: DO NOT INTERRUPT the upgrade process until it is complete. WARNING: You MUST complete the image file upgrade BEFORE upgrading the U-Boot and Miniboot files. Geni. 1 2 3 Download the 6.4.R01.4. file /flash/gminiboot. Interruption of the process will result in an unrecoverable failure condition.file /flash/ku-boot.4. WED APR 20 15:32:16 : CSM-CHASSIS (103) info message: +++ == CSM == timer_r:simplex---.bin copied +++ NI 1 software update started Erasing flash Writing 131072 bytes at 0xff900000 Erasing flash Writing 131072 bytes at 0xff920000 Erasing flash Writing 131072 bytes at 0xff940000 Erasing flash Writing 131072 bytes at 0xff960000 Erasing flash Writing 131072 bytes at 0xff980000 Erasing flash Writing 131072 bytes at 0xff9a0000 Erasing flash Writing 131072 bytes at 0xff9c0000 Verifying sectors of flash from (0xff900000) to (0xff9e0000) Done WED APR 20 15:31:47 : SYSTEM (75) info message: +++ NI 1 software update completed -. Part No.session end ---+++ == CSM == UPDATE COMPLETED +++ == CSM == Application & Watchdog Monitoring Started WARNING: DO NOT INTERRUPT the upgrade process until it is complete. 032731-10 Rev.uboot copied +++ NI 2 software update started WED APR 20 15:31:51 : SYSTEM (75) info message: +++ NI 2 software update completed -. 54 of 58 Upgrading an OmniSwitch to 6.4.file /flash/ku-boot.R01.4.OmniSwitch 6400 Upgrading an OmniSwitch to 6.uboot copied sysStartWatchdog() Starting watchdog timer to INTERRUPT after 60 secs.4.file /flash/gminiboot.bin copied +++ NI 2 software update started WED APR 20 15:32:08 : SYSTEM (75) info message: +++ NI 2 software update completed -.R01 Sample output for "update uboot-miniboot" for a stack of 2 WED APR 20 15:31:25 : SYSTEM (75) info message: +++ ---->SSACTION_UPDATE_UBOOT_MINIBOOT WED +++ +++ +++ APR 20 == CSM == CSM == CSM 15:31:25 : CSM-CHASSIS (103) info message: == Application & Watchdog Monitoring Stopped == Update bootrom on all slots == sysUpdate begin WED APR 20 15:31:26 : SYSTEM (75) info message: +++ NI 1 software update started Erasing flash Writing 131072 bytes at 0xfff00000 Erasing flash Writing 131072 bytes at 0xfff20000 Verifying sectors of flash from (0xfff00000) to (0xfff40000) Done WED APR 20 15:31:31 : SYSTEM (75) info message: +++ NI 1 software update completed -. A . Enter the following to delete the Gfpga.4. The display below shows a successful image file upgrade. FTP the FPGA upgrade kit file (Gfpga.4. all switches in a stack). use the show microcode command as shown below.R01.4.342.img Gos. -> show microcode Package Release Size Description -----------------+---------------+--------+----------------------------------Gbase.img 6.4.R01.R01 6. 1 2 Download the latest FPGA build from the Alcatel-Lucent Service and Support web site to your PC. Log into the primary switch.upgrade_kit file on the primary CMM: -> rm Gfpga.4.upgrade_kit Verifying the Upgrade with the CLI Verifying the Software Upgrade To verify that the software was successfully upgraded to 6.R01 OmniSwitch 6400 4 When the “UPDATE COMPLETED" message appears.img Geni. Part No.R01 6. Make sure you change the path of the destination directory from /flash/working (the default) to the root /flash directory before transferring the upgrade kit. WARNING: You MUST complete the image file and U-Boot/Miniboot upgrade BEFORE upgrading the FPGA. Enter: -> update fpga ni all 3 4 The FPGA will be updated on the primary switch (and.4.4.upgrade_kit file from the /flash directory.342.R01 16520637 Alcatel-Lucent Base Software 1769841 Alcatel-Lucent OS 5566177 Alcatel-Lucent NI software 606061 Alcatel-Lucent Security Management Upgrading an OmniSwitch to 6.upgrade_kit) to the /flash directory on the primary switch. A 55 of 58 . the following message will be displayed: +++ == CSM == UPDATE COMPLETED The switch will automatically reboot.Upgrading an OmniSwitch to 6.4. delete the Gfpga. delete the miniboot and u-boot files from the / flash directory.342.4. CMM.4.4. 5 After the FPGA upgrade has been successfully completed. When the update is complete. 032731-10 Rev. then reload the switch: -> reload working no rollback-timeout Upgrading the FPGA Follow the steps below to upgrade the FPGA to FPGA 16 on OS6400-C24 and OS6400-P24 switches.342.4.img Gsecu.4.R01 6. if present.4. Part No.R01 Verifying the U-Boot and Miniboot Upgrade To verify that the U-Boot and Miniboot files were successfully upgraded. . . 001. : 6400 24 FIBER PORTS W/STK. Freescale MPC8248. POWER ON. 56 of 58 Upgrading an OmniSwitch to 6.R01.565.4. UP . 00:e0:b1:8c:da:72. 0xe1bc.4.4. 0016/00. 6.3. C615HA02V 060403 850nm. JAN 26 2008.OmniSwitch 6400 Upgrading an OmniSwitch to 6. UP.Physical 1: FPGA . 6. BCM56322_A0. 6400 24 FIBER PORTS W/STK.Physical 1: UBOOT Version : UBOOT-miniboot Version : POE SW Version : GBIC 2 Manufacturer Name: Part Number: Hardware Revision: Serial Number: Manufacture Date: Laser Wave Length: Admin Status: Operational Status: Module in slot 2 PICOLIGHT . A . Information for each switch in a stack (if applicable) is displayed. -> show ni Module in slot 1 Model Name: Description: Part Number: Hardware Revision: Serial Number: Manufacture Date: Firmware Version: Admin Status: Operational Status: Power Consumption: Power Control Checksum: CPU Model Type MAC Address: ASIC . . POWER ON.4.3.R01. use the show ni command as shown below.R01. n/a PL-XPL-VC-S13-11.4. J0480060. 032731-10 Rev.4. 902623-90. 79.565. 3.4. Freescale MPC8248. A 57 of 58 .R01.3. 02. 6. BCM56322_A0. 6.R01. 902621-90. 0xc09f.4. 00:e0:b1:99:a4:54.R01. 032731-10 Rev.4. 6400 24 COPPER PORTS W/STK.4. J1480014. n/a Upgrading an OmniSwitch to 6. Part No.565.565.4. 0016/00.Physical 1: FPGA . 69.R01 OmniSwitch 6400 Model Name: Description: Part Number: Hardware Revision: Serial Number: Manufacture Date: Firmware Version: Admin Status: Operational Status: Power Consumption: Power Control Checksum: CPU Model Type MAC Address: ASIC . . UP.Upgrading an OmniSwitch to 6. APR 08 2008. POWER ON.Physical 1: UBOOT Version : UBOOT-miniboot Version : POE SW Version : : 6400 24 COPPER PORTS W/STK.4. R01 Upgrade/Downgrade Software Matrix Refer to the matrix below for software compatibility when upgrading/downgrading a 6400 Series Switch to/from Build 6.3.R01 F = 6.288.4.R01 F = 6.265.3.4. 032731-10 Rev.R01 GA F = 6.R01 F = 6.R01.g. Alcatel-Lucent 26801 West Agoura Road Calabasas.4.3.3.565.ind.4.265.R01 Contact Support Yes Yes Model 6400 Note.3 GA 6. contact Customer Support. contact Customer Support. when downgrading. Part No. Also.4.R01. Hardware is only backward compatible down to the software that originally supported it (e. 6.3.4.3. CA 91301 (818) 880-3500 FAX (818) 880-3505 US Customer Support: (800) 995-2696 International Customer Support: (818) 878-4507 Internet: http://eservice.4 GA 6.4.3.4.3 GA I = 6.R01 Build and Supported Software Versions For Each Upgrade 6.3.4.com 58 of 58 Upgrading an OmniSwitch to 6. make sure to load the applicable U-Boot/Miniboot files.3.OmniSwitch 6400 Upgrading an OmniSwitch to 6.alcatel.4.3.3.R01 I = 6.4. Upgrade/Downgrade Matrix 6.4. I = Image Files F = U-Boot/Miniboot Yes = You can upgrade/downgrade to the next build.R01 I = 6. For more information.R01 GA I = 6. N/A = Not applicable..4.3.4. No = You cannot upgrade/downgrade to the next build.4.4.R01 for the 6400). A .3. For more information.