OAU004301 UMG8900 Data Configuration and Routine maintenance R003ISSUE 2.0 Fixed Network Curriculum Development Section Introduction Before configuring the data, you should first have some knowledge about the networking and user requirements, and collect the basic required by data configuration. information The configuration should follow the basic sequence and configuration requirement. This course mainly introduces the basic procedures, configuration method, basic configuration principles, and hardware and interface configuration. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Objectives Upon completion of this course, you will be able to: Know basic procedures, method, and principles of configuration; Master UMG8900 Configuration; Data Master UMG8900 Routine Operation and Maintenance. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal References U-SYS™ UMG8900 Data Configuration Manual Data Configuration U-SYS™ UMG8900 Universal Media Gateway Operation Manual Routine Operation and maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Course Contents Data Configuration Routine operation Routine maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Procedure of Data Configuration Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Configuration Overview The data configuration of UMG8900 is mainly completed through the MML command. LMT client software mainly completes the configuration management and maintenance of system. Before performing data configuration, firstly collect the detailed networking information . Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Data Collection MGW Side Related Parameter IP address and route over the interface MGW ID Transmission protocol type Authentication Mode SCTP protocol initialization parameter Call processing metrics Media resource processing metrics Consider the whole network to plan Plan in advance MGC Side Related Parameter IP address and route MGC ID Transmission protocol type Authentication Mode SCTP protocol initialization parameter Consider the whole network to plan Plan in advance Keep consistent with MGW Keep consistent with MGC Consistent with MGC When the transmission protocol type is SCTP, configure SCTO initialization parameter according to actual condition Distribution rate between PPU and CMU. Plan in advance. Distribution rate between CMU and VPU. Plan in advance. Consistent with MGW Consistent with MGW Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Logical board and Physical board Logical Board: It means the boards are classified and named based on the functions. “Board type” is corresponding to the logical board. Physical Board: It finally reflects the distinction in software/hardware configuration of board. “Hardware type” is corresponding to the physical board. For Example :OMU is loglic Board name;FOMU is Physical Board name. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Hardware Configuration Procedure Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Introduction to Frame Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Frame Configuration Command •Add a central switch frame: ADD FRM: FN=1, FT=CONTROL; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Principle for Board Configuration In the main control frame, the FOMU, FNET and FCLK boards have been added by default. FOMU is inserted in the front slot 7 and slot 8 in the main control frame (plug-in frame 1), FCLK is in the back slot 0 and 1 (plug-in frame 1). FOMU/FMPU and FNET must be inserted front and back opposite each other. Front-inserted boards : FOMU, FMPU, FFLU, FCMF, FVPU, FSPF and FHRU. Back-inserted boards : FTNU, TCLU, FCLK, FBLU, FCMB and FNET. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Principle for Board Configuration All the interface boards can be inserted in any back slots except slot 6, 7, 8 and 9 (Only FCLK can be inserted in the back slot 0 and 1 of main control frame): FG1O, FE8T, FP4L, A4LM/A/B/C, FA4L, E32 and S2L/A/B/C. Some boards have strict front-back opposite plug-in requirement. The boards with front-back plug-in requirement include: FFLU (front) and FBLU (back), FHRU (front) and FG1O and E1GM/A/B/C, FA4L, FBAP, FBFE, FBGE, FE8T (Back), FMPU/FOMU (front) and FNET (back). Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Configure cascading between 2 frame Configure cascading between the main control frame and the central switch frame: ADD FRMLNK: TP=TNU, LKBN=0; Configure the cascading between the service frame and the central switch frame: ADD FRMLNK: TP=BLU, BN=0, LKBN=1; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal SSM: Synchronous Status Message SSM, namely the synchronous status message, and is also called synchronous quality information. SSM is used to reflect the level of synchronous timing signal directly in synchronous timing transmission link. For the line clock source, SSM is extracted by the line interface board and reported to FOMU, and then FOMU configures the SSM of line clock source to clock module. If the external synchronous reference source of clock module is 2048kbit/s signal, the clock module can extract SSM from signal. For GPS reference source, FOMU does not set the SSM level and its level is PRC constantly. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Reference Source Selection Reference Source Selection Manual mode? Y Y N SSM participates in control? Specify the master reference source and handover is not performed N Based on priority In sequence: GPS, Line1, Line2, Ext End Confidential Information of Huawei. No Spreading without Permission. According to the SSM level Security Level: Internal Clock Configuration Command •Designate line clock as the clock source and grade 2 as the clock grade: MOD CLK: MODE=MANUAL, GRADE=TWO, SRC=LINE1; •Configure clock to extract clock from the port 0 on the E32 0: SET LINECLK: LINE=LINE1, BT=E32, BN=0, PN=0; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Two-Frame Cascading Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Board Configuration Command •Add boards to the main control frame: ADD BRD: FN=1, SN=1, BP=FRONT, BT=VPU, HBT=FVPB, BS=LOADSHARE, BN=1, ADS=ACTIVE; ADD BRD: FN=1, SN=6, BP=BACK, BT=TCLU, HBT=TCLU, BS=ONEBACKUP, BN=0; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Configuration Procedure MGW configuration Interface configuration is completed? N Interface IP configuration, route configuration and firewall configuration (optional) Y Is it necessary to modify SCTP parameter? Y N SCTP initialization parameter modification Y Set package forwarding (optional) N Set MGW label Add MGC Signalling link configuration Call process distribution rate configuration: PPU:CMU Is it necessary to modify H.248 parameter? Y H.248 protocol parameter configuration Activate MGW device N Media resource process distribution rate: CMU:TCU End Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Relationship between MGW tables Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Configure IP interface Configure the IP address of the OMU 0: ADD IPADDR: BT=OMU, BN=0, IFT=ETH, IFN=0, IPADDR="10.1.1.1", MASK="255.255.255.0"; Configure the route from the OMU 0 to the SoftX3000: ADD ROUTE: BT=OMU, BN=0, DSTIP="192.168.0.1", RTTYPE=NEXTHOP, DSTMASK="255.255.255.0", NEXTHOP="10.1.1.254"; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal MGW Control Data Configuration Configure VMGW SET VMGW: VMGWID=0, MIDTYPE=IP, MID="10.1.1.1:5555", IPNUM=50000, TDMNUM=30000; Configure the master MGC ID ADD MGC: VMGWID=0, MGCIDX=0, MIDTYPE=IP, MID="192.168.0.1:2944", MSS=MASTER; Configure H.248 protocol : SET H248PARA: VMGWID=0, CT=BINARY, TT=UDP; Configure an H.248 signaling link ADD H248LNK: BN=0, LINKID=0, VMGWID=0, MGCIDX=0, PEERIP="192.168.0.1", PEERPORT=2944, LOCALIP="10.1.1.1", LOCALPORT=5555, LINKNAME="To-Master MGC"; Activate the VMGW: ACT VMGW: VMGWID=0; Security Level: Internal Confidential Information of Huawei. No Spreading without Permission. SG Configuration Procedure Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Configure SS7 LINK Configure M2UA link set and links to the SoftX3000: ADD L2UALKS: PROTYPE=M2UA, LKS=0; Configure M2UA links from the SPF 0 to the master SoftX3000: ADD L2UALNK: PROTYPE=M2UA, BN=0, LNKNO=0, LKS=0, LOCALPN=6666, LOCALIP1="10.1.1.3", REMOTEPN=2904, REMOTEIP1="192.168.0.1", PRIO=0; Configure MTP2 links to the PSTN switch ADD MTP2LNK: LNKNO=0, LKS=0, BINIFID=1, LNKTYPE=M2UA64K, IFBT=E32, IFBN=0, E1T1N=1, STRTTS=16, SPFBN=0, SUBBN=0, BITREVERSE=OFF; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal TDM Bearer Configuration Process UMG8900 only needs to accomplish the configuration of various types of circuits. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal IP Bearer Configuration Procedure IP Bearer Configuration Interface IP address configuration of HRB Route (Optional) & gateway configuration Set VPU bearer relationship End Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal IP Bearer Configuration Configure TDM connections to the PSTN switch. TDMIU: BN=0, BT=S2L, TIDFV=0, TIDLV=4095, ADD VMGWID=0; ADD TDMIU: BN=3, BT=S2L, TIDFV=12288, TIDLV=16383, RT=INSIDE, VMGWID=0; Configure gateway address: ADD GWADDR: BT=HRB, BN=0, IPADDR="10.10.1.254", MASK="255.255.255.0"; Configure bearer relation: ADD BEARREL: BN=0, IP="10.10.1.1"; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal RSP Configuration Procedure RSP Configuration Configure RSP Frames and Boards Add Asynchronous Tone Configure TDM Resource Configure E1 on RSP Board End Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Configure RSP Add UAM frames ADD UAFRM: FN=1, PN=0, RN=0, RFN=1, FT=RSP10, FM=MAIN, BN=0, VMGWNO=0; Add boards to the master frame: ADD UABRD: FN=1, SN=3, BT=ASL; Configure asynchronous tones: ADD ATONE: BT=VPU, BN=0, TONEID=RINGTONE; Configure RSP E1 connections ADD UACFG: FN=1, SN=9(RSP), E1SRC=E32, BN=0(SPF), SBN=0, BN0=2, PN0=0, BN1=2, PN1=1; Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Debug RSP Configuration 1. Check if the physical ports are connected via the command DSP E1PORT. 2. 3. Check the board status of E32, TNU, SPF and OMU. Check if the time slot of asynchronous tone is configured via the command LST ATONE. 4. Check if the time slot type of RSP frame is correctly configured via the command LST TDMIU. 5. Check if E1 of RSP is correctly configured via the command LST RSPCFG. 6. 7. Check if the clock board status is normal. Check if the semi-permanent connection status to RSP board is normal via the command LST TDMSPC. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Course Contents Data Configuration Routine Operation Routine Maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Local Maintenance Terminal System LMT system: Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Local Maintenance Terminal System UMG8900 Operation Online Help: It is used for viewing help information of systems. UMG8900 Operation and Maintenance System: It is used for data configuration, device operation and maintenance and right setting, and so on. UMG8900 Alarm Management System: It is used for alarm query and process. UMG8900 Performance Management System: It is used for creating performance measure task and displaying results. UMG8900 Trace Viewer: It is used for viewing the traced messages during off line. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Operation and Maintenance System There are two modes to start the operation and maintenance system: Run [Start/programs/Huawei UMG8900 local maintenance and terminal/UMG8900 Maintenance System]. V100R003/UMG8900 Operation On the alarm management system interface, select [System/Open Operation and Maintenance System], or click on the tool bar. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Main interface of operation and maintenance system (1) (2) (3) 1.Main interface of operation and maintenance system (4) (6) (1) Menu bar (4) Information output window Confidential Information of Huawei. No Spreading without Permission. (2) Tool bar (5) Status bar a (3) Navigator window (6) Status bar b (5) Security Level: Internal Alarm Management System (1) (2) (3) (1) Menu bar (4) Status bar Confidential Information of Huawei. No Spreading without Permission. (2) Tool bar (3) Navigator window (4) Security Level: Internal Performance Management System (1) (2) (3) (5) (4) (6) (1) Menu bar (4) Information output window Confidential Information of Huawei. No Spreading without Permission. (2) Tool bar (5) Task information window Security Level: Internal (3) Navigator window (5) Status bar Trace Viewer (1) (2) (3) (1) Menu bar (2) Tool bar (3) Navigator window Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Login Infomation User name/User description: admin Password/Confirm password: 9061mgw site ip:omu board ip (for example:190.1.30.1); site name:random define (for example:Local Host); Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal System Management －Routine command Command LST FILE Function List the related information of various types of data files at OMU. BCK FILE Dump the specified file manually to the server set by MOD MFTP. ADD FTPUSR SET FTPSRV CPY Add an FTP user. The user information includes user name, password, working directory and authority. Open/Close FTP server and set timeout for server at the same time. Copy the source files to the destination directory. CRE RTSTTSK Create a routine test task for the specified device on the BAM. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Service Management－Routine Command Command DSP IPIF DSP E1PORT DSP TDMSTAT Function Query the status of the link layer protocol on an interface and the statistics information of sending/receiving packets. Query the status of the E1/T1 interface. Query the statuses of TDM timeslots so as to learn about which timeslots are occupied and which timeslots are idle in the current E1/T1 interface. Query the configuration of timeslots on various TDM interface boards. Query the SCTP connection information. LST TDMIU DSP SCTPCON DSP L2UALKS Query the status of the M2UA, IUA, V5UA link group.The status of the normal link group is ACTIVE. DSP L2UALNKQuery the status of the M2UA, IUA, V5UA link.The status DSP L2UALNK of the normal link is ACTIVE. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Service Management－Routine Command Command Function Query the connection status of the H.248 signaling link.The status of the normal link is UP. Query the status of the VMGW and the selected MGC. Activate/Deactivate the VMGW. Query the status of the board clock. Query the corresponding TID value on the port based on the location information of the user port. Query the location information of the user port based on the TID value on the port. DSP H248LNK DSP VMGW ACT/DEA VMGW DSP CLK LST UATID LST UAPOS Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Course Contents Data Configuration Routine operation Routine maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Maintenance Overview Basic tasks and main maintenance contents are described as follows. 1.Make sure that the devices operate normally, and that their electric performance, mechanical performance, technical indices and various service indices conform to the standards. 2.Perform network optimization, so as to ensure that the coverage area can obtain high communication quality. 3.Fast and exactly remove various communication faults to ensure smooth communications. 4.Perform the cooperation between entire networks in the whole running process to ensure a reliable internet operation. 5.Make sure that new devices and capacity-expansion devices are correctly connected to the networks. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Common Methods I. Comparison method II. Substitution method III. Minimum system method IV. Protocol tracing analysis method Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Basic Requirements for Maintenance Personnel I. Special qualification and skills II. Familiarity with the system and networking III. Operation IV. Instrument and meters Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Equipment Room Maintenance I. Sudden maintenance II. Routine maintenance III. Periodic maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Maintenance Table and Operation Guide I. Routine keep-watch maintenance table II. Maintenance task plan III. Itinerant checking maintenance IV. Designated maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Network Management 1. Performance statistics indices as running data, interface flow, resource utilization and data flow. 2. Network optimization I. II. System investigation Data analysis III. Optimization scheme drawing and implementation Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Routine Maintenance Operation Guide Routine maintenance mainly involves equipment room, device running status, functional subsystems, service bearer and media resources, signaling and description of routine maintenance items. Routine Maintenance Type: Daily Routine Maintenance Monthly (Quarterly) Maintenance Yearly Maintenance Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Daily Routine Maintenance Items Maintenance items Air conditioner Power supply transmission Tools, meters and documents On-duty personnel tasks Troubles remained Operation Check the cooling degree, switch, etc. of the air conditioner. Check if the power supply has open circuit. Check if interruption, error codes, etc. happening to the transmission system. The tools, meters and maintenance documents shall be complete and intact; otherwise additional explanation shall be given. Sum up the jobs on duty, including the description and the handling of the faults discovered on this duty and the left faults of the last duty. Describe the faults that have not been completely fixed yet, including the fixing status and the fault severity. The chief operator checks the on-duty jobs to make sure that jobs are smoothly handed over, faults are fixed and the equipment room is normally running. Monitor check Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Monthly (Quarterly) Maintenance Operation Guide 1. Termination System 2. System 3. Cabinet 4. Power Supply 5. Grounding wire 6. Spare Parts Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal Yearly Maintenance Operation Guide 1.Functional Subsystem Referenced standards Maintenance items The correctness of statistics reports Check if the statistics system is correct by means of comparison. 2.Connection Referenced standards Maintenance items Trunk connection Network cable connection Optical path connection Connection cables between racks Trunk connections are reliable, trunks are complete and intact, and labels are easily recognizable. Network cable connections are reliable, network cables are complete and intact, the hub is intact and labels are clear and explicit. The optical paths between racks are reliable, optical fibers are complete and intact, without being crushed to be flat or folded; labels are clear and explicit. The connection cables between racks are reliable, various cables are complete and intact, and labels are easily recognizable. Security Level: Internal Confidential Information of Huawei. No Spreading without Permission. Confidential Information of Huawei. No Spreading without Permission. Security Level: Internal
Report "OAU004301 UMG8900 Data Configuration and Routine Maintenance R003 ISSUE2.0 20050622"