Manual de Configuracion de Puerto Huawei

BSMCGTSMN1C1EPN0#display current-configuration on ^ % Too many parameters, the error locates at '^' BSMCGTSMN1C1EPN0#display current-configuration { <cr>|section<K>||<K>}: Command: display current-configuration [MA5616V800R307: 5101] # [global-config] <global-config> sysname BSMCGTSMN1C1EPN0 undo traffic table ip index 0 undo traffic table ip index 1 undo traffic table ip index 2 Estas son las tarjetas undo traffic table ip index 3 undo traffic table ip index 4 undo traffic table ip index 5 undo traffic table ip index 6 traffic table ip index 1 name "128" cir 128 cbs 6096 pir 128 pbs 6096 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 2 name "256" cir 256 cbs 10192 pir 256 pbs 10192 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 3 name "512" cir 512 cbs 18384 pir 512 pbs 18384 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 5 name "1024" cir 1024 cbs 34768 pir 1024 pbs 34768 color-mode color-blind priority 0 priority-policy local-setting Los index son las velocidades traffic table ip index 6 name "2048" cir 2048 cbs 67536 pir 2048 pbs 67536 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 7 name "64" cir 64 cbs 4048 pir 64 pbs 4048 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 11 name "ubr" cir off priority 0 priority-policy local-setting traffic table ip index 14 name "ubr_0" cir off priority 0 priority-policy local-setting adsl mode switch-to ADSL vdsl mode switch-to normal adsl line-profile quickadd 2 basic-para ADSL-all trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 2400 32 1280 name d2400u1280 adsl line-profile quickadd 3 basic-para ADSL-all trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 1024 32 512 name d1024u512 adsl line-profile quickadd 9 basic-para G992.5 trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 5888 32 1400 name d5120u1400 adsl line-profile quickadd 14 basic-para G992.5 trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 11468 32 1400 name 1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 615 32 615 name BSMCGTSMN1C1EPN0#display current-configuration on ^ % Too many parameters.1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 160 32 160 name Corporativo_128 adsl line-profile quickadd 62 basic-para G992.1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 320 32 320 name Corporativo_256 adsl line-profile quickadd 63 basic-para G992. the error locates at '^' BSMCGTSMN1C1EPN0#display current-configuration { <cr>|section<K>||<K> }: Command: display current-configuration [MA5616V800R307: 5101] # [global-config] <global-config> sysname BSMCGTSMN1C1EPN0 undo traffic table ip index 0 undo traffic table ip index 1 undo traffic table ip index 2 undo traffic table ip index 3 undo traffic table ip index 4 undo traffic table ip index 5 undo traffic table ip index 6 traffic table ip index 1 name "128" cir 128 cbs 6096 pir 128 pbs 6096 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 2 name "256" cir 256 cbs 10192 pir 256 pbs 10192 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 3 name "512" cir 512 cbs 18384 pir 512 pbs 18384 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 5 name "1024" cir 1024 cbs 34768 pir 1024 pbs 34768 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 6 name "2048" cir 2048 cbs 67536 pir 2048 pbs 67536 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 7 name "64" cir 64 cbs 4048 pir 64 pbs 4048 color-mode color-blind priority 0 priority-policy local-setting traffic table ip index 11 name "ubr" cir off priority 0 priority-policy local-setting traffic table ip index 14 name "ubr_0" cir off priority 0 priority-policy local-setting adsl mode switch-to ADSL .Turbonett_10M adsl line-profile quickadd 61 basic-para G992. 5 trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 11468 32 1400 name Turbonett_10M adsl line-profile quickadd 61 basic-para G992.50 NOC loghost activate ip 10.50 .1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 320 32 320 name Corporativo_256 adsl line-profile quickadd 63 basic-para G992.22.10.22.1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 896 32 896 name Corporativo_768 adsl line-profile quickadd 65 basic-para G992.1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 615 32 615 name Corporativo_512 adsl line-profile quickadd 64 basic-para G992.5 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 1180 32 1180 name Corporativo_1024 trap convert event-to-alarm 0x3721000a event eventlevel 0x0230a042 minor alarm alarmlevel 0x0a11a102 warning alarm alarmlevel 0x0a11a103 warning alarm alarmlevel 0x0a11a104 warning alarm alarmlevel 0x0a11a105 warning alarm alarmlevel 0x0a11a106 warning alarm alarmlevel 0x0a11a107 warning alarm alarmlevel 0x0a11a109 warning alarm output alarmid 0x0a31002d alarm alarmlevel 0x0a310112 warning alarm alarmlevel 0x0a310142 warning alarm output alarmid 0x0a32002d event eventlevel 0x3f100004 minor event eventlevel 0x3f100005 minor event eventlevel 0x3f300001 default trap filter event condition id 0xa300012 trap filter event condition id 0xa300013 trap filter event condition id 0xa300015 trap filter event condition id 0xa300052 loghost add 10.5 trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 5888 32 1400 name d5120u1400 adsl line-profile quickadd 14 basic-para G992.10.vdsl mode switch-to normal adsl line-profile quickadd 2 basic-para ADSL-all trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 2400 32 1280 name d2400u1280 adsl line-profile quickadd 3 basic-para ADSL-all trellis 1 bitswap 0 0 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 1024 32 512 name d1024u512 adsl line-profile quickadd 9 basic-para G992.1 trellis 1 bitswap 1 1 channel interleaved 8 8 adapt at-startup snr 6 0 16 6 0 16 rate 32 160 32 160 name Corporativo_128 adsl line-profile quickadd 62 basic-para G992. 22. 0/# deactivate 2 slot) activate 2 profile-index 2 deactivate 3 activate 3 profile-index 9 deactivate 4 activate 4 profile-index 2 deactivate 7 .10.# [device-config] <device-config> board add 0/1 ADL board add 0/2 ADL # [public-config] <public-config> timezone GMT.128 udp-port 162 trap-paramsname default_para snmp-agent target-host trap-paramsname default_para v1 securityname public snmp-agent trap enable standard # [vlan-config] <vlan-config> vlan 177 smart vlan 1198 smart vlan 1400 to 1402 smart vlan desc 177 description "VoIP" vlan desc 1198 description "Turbonett_Prepago" vlan desc 1400 description "Administracin" vlan desc 1401 description "Turbonett+" vlan desc 1402 description "PPPoE" port vlan 177 0/0 0 port vlan 1198 0/0 0 port vlan 1400 to 1402 0/0 0 # [adsl] <adsl-0/1> interface adsl 0/1 deactivate 0 activate 0 profile-index 9 deactivate 1 Primero se desactiva y luego se activa con el profile line activate 1 profile-index 2 que le corresponde (enable* config* interface adsl.06:00 system handshake interval 10 snmp-agent local-engineid 800007DB0300464BBE18A5 snmp-agent community read public snmp-agent community write private snmp-agent target-host trap-hostname BMS_N2000 address 10. activate 7 profile-index 9 deactivate 15 activate 15 profile-index 2 deactivate 31 activate 31 profile-index 2 # <adsl-0/2> interface adsl 0/2 deactivate 0 activate 0 profile-index 14 deactivate 7 activate 7 profile-index 9 deactivate 15 activate 15 profile-index 2 deactivate 31 activate 31 profile-index 2 # [port-config] <port-config> port desc 0/1/0 description "79254052" port desc 0/1/1 description "79254048" port desc 0/1/2 description "79254061" port desc 0/1/3 description "79254020" port desc 0/1/4 description "79254148" # [emu-config] <emu-config> emu add 1 fan 0 2 RS485 "FAN" # [fan] <fan-1> interface emu 1 fan speed mode automatic # [bbs-config] <bbs-config> service-port 0 vlan 1402 adsl 0/1/0 vpi 0 vci 32 single-service rx-cttr 11 tx-cttr 11 service-port 1 vlan 1402 adsl 0/1/7 vpi 0 vci 32 single-service rx-cttr 11 tx-cttr 5 service-port 2 vlan 1402 adsl 0/1/15 vpi 0 vci 32 single-service rx-cttr 6 tx-cttr 5 service-port 3 vlan 1402 adsl 0/1/31 vpi 0 vci 32 single-service rx-cttr 5 tx-cttr 3 service-port 4 vlan 1402 adsl 0/2/0 vpi 0 vci 32 single-service rx-cttr 11 tx-cttr 5 Los profile line son los perfiles de fuera Esta línea ya es la configuración del puerto en Si. se debe quitar el número correlativo que va antes de la palabra vlan y modificar los daros según los puertos anteriores . service-port 5 vlan 1402 adsl 0/2/7 vpi 0 vci 32 single-service rx-cttr 11 tx-cttr 5 service-port 6 vlan 1402 adsl 0/2/15 vpi 0 vci 32 single-service rx-cttr 6 tx-cttr 5 service-port 7 vlan 1402 adsl 0/2/31 vpi 0 vci 32 single-service rx-cttr 5 tx-cttr 3 # [vlanif] <vlanif1400> interface vlanif1400 ip address 10.255.35.0.200 255.255.255.224 # [meth] <meth0> interface meth0 ip address 192.0 # [null] <null0> interface null0 Estos son los comandos para configurar un puerto en HUAWEI BSMCGTSMN1C1EPN0# BSMCGTSMN1C1EPN0#config BSMCGTSMN1C1EPN0(config)#interface adsl 0/1 BSMCGTSMN1C1EPN0(config-if-adsl-0/1)#deactivate 4 BSMCGTSMN1C1EPN0(config-if-adsl-0/1)# Deactivate port 4 successfully SMCGTSMN1C1EPN0(config-if-adsl-0/1)# quit BSMCGTSMN1C1EPN0(config)#service-port vlan 1402 adsl 0/1/4 vpi 0 vci 32 single-service rx-cttr 2 tx-cttr 3 BSMCGTSMN1C1EPN0(config)#interface adsl 0/1 BSMCGTSMN1C1EPN0(config-if-adsl-0/1)#activate 4 profile-index 2 BSMCGTSMN1C1EPN0(config-if-adsl-0/1)# .22 255.255.168.72.