Manage IP Based Route

Page 1 of 3QRU - MANAGE IP BASED ROUTE IDENTIFIER LIST Function Use this command to configure, delete or modify identifier parameters of IP-based route network. Parameters action mode : ip_based_route identifier , ip_based_route_name : ip_based_route_bandwidth : committed_bandwidth : committed_signal_bandwidth : committed_dcn_bandwidth : ifc_option , ifc_ratio : mux_enable , local_mux_port , remote_mux_port , max_packets , mux_dscp ; Syntax QRU:<action mode>:<ip_based_route_id>,<ip_based_route_name>: [ip_based_route_bandwidth]:[committed_bandwidth]: [committed_signal_bandwidth]:[committed_dcn_bandwidth]: [ifc_option],[ifc_ratio]: [mux_enable],[local_mux_port],[remote_mux_port], [max_packets],[mux_dscp]; Parameter explanations action mode This parameter identifies action mode of network identifier list for IP-based route. There are three action modes. ADD DEL MOD Add a new IP-based route network into list. For this action mode, IP-based route name is obligatory, but IP-based route id is not. Delete an existing IP-based route network from list. For this action mode, either IP-based route name or IP-based route id or both should be specified. Modify an existing IP-based route network. For this action mode, IP-based route id is obligatory, but IP-based route name is not. ip_based_route_id An identifier number of IP-based route network. The available range is from 1 to 4095 in decimal. This parameter value is unique in whole identifier list. This parameter is obligatory when the action mode is MOD. ip_based_route_name The identifier name of IP-based route network. The name can contain the following characters: letters A-Z, a-z, numbers 0-9, dot (.), and hyphen (-). The maximum length of name is 16 characters. The name is given in quotation marks. This parameter is obligatory when the action mode is ADD. ip_based_route_bandwidth The bandwidth of the IP-based route. The allowed value range is 0Kbps - 1000Mbps, with an increment of 1Kbps. The default value is 0Kbps. It is a L2 layer bandwidth that is used for IFC. Bandwidth shaping is made based on this parameter. When the action mode is ADD and Connection Admission Control (CAC) is requested, this parameter is obligatory. This also means that if any of committed_bandwidth,committed_signal_bandwidth, or committed_dcn_bandwidth is specified in ADD mode, ip_based_route_bandwidth cannot be skipped. committed_bandwidth The committed bandwidth of IP-based route network. This parameter is used for CAC, which means CAC is configured based on this parameter. The allowed value range is 0Kbps - 1000Mbps, with an increment of 1Kbps. The default value is 0Kbps. committed_signal_bandwidth The committed signal bandwidth of IP-based route network. This parameter is excluded from CAC and IFC. The allowed value range is 0kbps - 50Mbps, with an increment of 1 Kbps. The default value is 0Kbps. committed_dcn_bandwidth The committed dcn bandwidth of IP-based route network. This parameter is excluded from CAC and IFC. The allowed value range is 0Kbps 1Mbps, with an increment of 1Kbps. The default value is 0Kbps. ifc_option This parameter specifies whether there is internal flow control for the IP-based route. The parameter can have value ON or OFF. The default value is OFF. When the action mode is MOD, this parameter cannot be modified. ifc_ratio This parameter defines the ratio of Iur_user_traffic_bandwidth to total_user_traffic_bandwidth. The allowed value range is 0 - 100, with an increment of 1. The default value is 20. This parameter is valid only when the ifc_option parameter is ON. mux_enable IP multiplexing option. This parameter defines whether the license based FP small packet multiplexing feature is enabled. The feature can only be enabled on NPGE(P). The valid values are ON and OFF, and the default value is OFF. local_mux_port http://127.0.0.1:43231/NED/NED?service=printview&library=a25003a0000c0800476p... 8/25/2014 It's only valid when IFC is on. The value is an integer within the range from 49152 to 65535. The value is an integer within the range from 5 to 30. Identifier ID of IP-based route network. QRU:ADD:2. Delete the existing identifier of "CMCC-5".--------. Ratio of lur user traffic bandwidth to total user traffic bandwidth.--------.50001. 6. The default value is 65535. The default value is 30. Add a new identifier of IP-based route network into list. Modify the IP multiplexing related values of IP-based route “ROUTE2”. max_packets This parameter indicates the maximum number of packets that will be multiplexed. QRU:MOD:2.--------1 2 ROUTE2 1000000 1000000 50000 1000 ON 50001 50002 30 COMMAND EXECUTED The execution printout of command example 3 is as follows: IFC RATIO DSCP --OFF 46 ----N/A CONFIGURED IP BASED ROUTE ROUTE BW SEQ ID NAME (KBPS) COMMITTED COMMITTED COMMITTED BW SIG BW DCN BW (KBPS) (KBPS) (KBPS) IFC RATIO http://127. It indicates that only the FP traffic with the specified DSCP value can be multiplexed. QRU:MOD:2.80."CMCC-5". Additional information The identifier list of IP-based route network can be interrogated using the command QRL.---------------. Execution printouts The following abbreviations are used in the execution printouts: SEQ ID NAME ROUTE BW COMMITTED BW COMMITTED SIG BW COMMITTED DCN BW IFC RATIO Sequence number of IP-based route. Examples 1. The default value is 65535."ROUTE2":1000000:1000000:50000:1000:OFF:ON. QRU:MOD:2. Parameters mux_enable.0. and mux_dscp are valid in the ADD and MOD action mode. QRU:MOD:2. 2. Internal Flow Control for User Plane Traffic. The maximum count of identifier in list is 4095 items.---. It shows the IP-based routes in an ascending order. The value is an integer within the range from 49152 to 65535.75. local_mux_port. Committed signaling bandwidth. Modify the committed bandwidth of IP-based route. mux_dscp This parameter defines the DSCP value of the multiplexed connection.---------."CMCC-5":::::ON. Modify the IP-based route ifc ratio."CMCC-5":20000:10000:3000:300:ON. 4.--300 ON RATIO ----80 The execution printout of command example 2 is as follows: CONFIGURED IP BASED ROUTE ROUTE BW COMMITTED COMMITTED COMMITTED BW SIG BW DCN BW SEQ ID NAME (kbps) (kbps) (kbps) (kbps) MUX LOCAL MUX REMOTE MUX MAX ENABLE PORT PORT PACKETS ---.Page 2 of 3 This parameter indicates the local ports for demultiplexing..."CMCC-5". max_packets.--------------. Committed bandwidth."CMCC-1":20000:20000:3000:300:ON.50002. Identifier name of IP-based route network. 5. remote_mux_port.--------1 2 CMCC-1 20000 20000 COMMAND EXECUTED COMMITTED SIG BW (KBPS) --------3000 COMMITTED DCN BW (KBPS) IFC --------. Route bandwidth of IP-based route network.80.--------. remote_mux_port This parameter indicates the remote ports for demultiplexing. The value is an integer within the range from 0 to 63. Committed data communication network bandwidth.1:43231/NED/NED?service=printview&library=a25003a0000c0800476p. The default value is 46. 3. Modify identifier name fto "CMCC-5".---. QRU:DEL:.0. 8/25/2014 . The execution printout of command example 1 is as follows: CONFIGURED IP BASED ROUTE ROUTE BW COMMITTED BW SEQ ID NAME (KBPS) (KBPS) ---. Give the route name again so that it meets the requirements specified in Parameter explanation.--.---. make sure ip_based_route_bandwidth equals to or is larger than committed_bandwidth. or committed_dcn_bandwidth is too large.--------. /*** INVALID PARAMETER ***/ You have given a wrong combination of parameters.---------. Check the information by QRL and change the ID or NAME. Check the IP-based route network configuration with QRB and remove it by QRA.---------.--------. committed_signal_bandwidth.--------1 2 CMCC-5 20000 10000 COMMAND EXECUTED The execution printout of command example 5 is as follows: COMMITTED COMMITTED SIG BW DCN BW (KBPS) (KBPS) IFC RATIO --------. /*** IFC METHOD CAN NOT BE MODIFIED ***/ You have tried to modify the IFC method.---. /*** IP BASED ROUTE ID IS ILLEGAL ***/ You have given an incorrect IP-based route id.0. Note that when you give bandwidth related parameters. Give the id as a decimal in the range of 1 to 4095.--. The IFC method can not be modified after it has been created in IP-based route. If an error occurs. Execution error messages /*** SEARCH KEY NOT FOUND ***/ You have given an IP-based route id or name that refers to a non-existing IP-based route network.--300 ON RATIO ----75 Semantic error messages /*** INVALID IP BASED ROUTE NAME ***/ You have given an incorrect identifier name. /*** IPMUX CAN NOT SET ENABLE WHEN LICENCE IS OFF ***/ You have tried to set the value of IP multiplexing option to ON while the license for feature RAN1886 is not turned on. /*** TOO MANY CHARACTERS ***/ You have given an IP-based route network name that is longer than 16 characters.----3000 300 ON 80 ROUTE BW COMMITTED COMMITTED COMMITTED BW SIG BW DCN BW SEQ ID NAME (KBPS) (KBPS) (KBPS) (KBPS) IFC RATIO ---.--------------. /*** IP BASED ROUTE NAME IS MISSING ***/ You have not given the parameter IP based route name.--------.--------.---------.--------------.1:43231/NED/NED?service=printview&library=a25003a0000c0800476p. the system may also outputs a general MML execution error message.--------------. /*** PARAMETER SET IS IN USE ***/ You have tried to delete an IP-based route which is bound to an interface. You may also have tried to create an IP-based route which has a same ID or Name of an existing IP-based route.--------------. Give the route name again so that it meets the requirements specified in Parameter explanation.--------.0.--------..---------.---..----1 2 CMCC-5 20000 10000 3000 300 ON 75 COMMAND EXECUTED The execution printout of command example 6 is as follows: DELETED IP BASED ROUTE ROUTE BW COMMITTED BW SEQ ID NAME (KBPS) (KBPS) ---. 8/25/2014 . The system may also output a general MML semantic error message. Turn on the license and give the command again. /*** NUMBER TOO BIG ***/ The value you have given for ip_based_route_bandwidth.Page 3 of 3 ---.--1 2 CMCC-5 20000 20000 3000 300 ON COMMAND EXECUTED ----80 The execution printout of command example 4 is as follows: CONFIGURED IP BASED ROUTE ROUTE BW COMMITTED BW SEQ ID NAME (KBPS) (KBPS) ---.--------. DN0173161 Id: 0900d80580a29403 ©2013 Nokia Siemens Networks http://127. and committed_bandwidth is larger than the sum of committed_signal_bandwidth and committed_dcn_bandwidth.--------1 2 CMCC-5 20000 10000 COMMAND EXECUTED COMMITTED SIG BW (KBPS) --------3000 COMMITTED DCN BW (KBPS) IFC --------. Check the allowed value range in the Parameter explanation. committed_bandwidth.---.