LTE TDD B2328-42V100R001C00 User Guide Issue 01 Date 2016-07-10 HUAWEI TECHNOLOGIES CO., LTD. Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website: http://www.huawei.com Email:
[email protected] Content Contents ............................................................................................................................................ ii 1 About this Guide ........................................................................................................................... 1 1.1 Prerequisite Skills and Knowledge ............................................................................................................................... 1 1.2 Conventions Used in this Document ............................................................................................................................. 1 2 Introduction.................................................................................................................................... 3 2.1 Product Overview ......................................................................................................................................................... 3 2.2 Product Package............................................................................................................................................................ 3 2.3 Connectors .................................................................................................................................................................... 4 2.4 LED Indicators.............................................................................................................................................................. 5 2.5 Installation .................................................................................................................................................................... 7 2.5.1 Installing LTE Outdoor CPE ...................................................................................................................................... 7 2.5.2 Connecting the Cable ................................................................................................................................................. 9 3 Web Interface ............................................................................................................................... 11 3.1 Login to Web-GUI ...................................................................................................................................................... 11 3.2 Function Button .......................................................................................................................................................... 13 3.3 Status and device information ..................................................................................................................................... 15 3.3.1 Status> Device Status .............................................................................................................................................. 15 3.3.2 Status> Modem Status ............................................................................................................................................. 17 3.3.3 Status> Telephony Status ......................................................................................................................................... 20 3.3.4 Status> About........................................................................................................................................................... 20 3.3.5 Status> Help............................................................................................................................................................. 21 3.4 Menu Structure ........................................................................................................................................................... 21 4 Reference Manual ....................................................................................................................... 23 4.1 Management ............................................................................................................................................................... 23 4.1.1 Management >Setup Wizard .................................................................................................................................... 23 4.1.2 Management>Modem Setup .................................................................................................................................... 26 4.1.3 Management>WAN Setup ....................................................................................................................................... 28 4.1.4 Management>LAN Setup ........................................................................................................................................ 32 4.1.5 Management>IPv6 ................................................................................................................................................... 35 4.1.6 Management> Telephony......................................................................................................................................... 39 4.1.7 Management>Diagnostics ....................................................................................................................................... 47 Issue 01 (2015-07-10) Huawei Proprietary and Confidential ii Copyright © Huawei Technologies Co., Ltd. 4.1.8 Management> System Log ...................................................................................................................................... 49 4.2 Personalization ............................................................................................................................................................ 51 4.2.1 Personalization>PIN Management .......................................................................................................................... 51 4.2.2 Personalization>Configuration ................................................................................................................................ 54 4.2.3 Personalization>Device Setup ................................................................................................................................. 55 4.2.4 Personalization>Software ........................................................................................................................................ 58 5 Reference Manual .......................................................................Error! Bookmark not defined. 5.1 Basic>Firewall ............................................................................................................................................................ 60 5.2 Basic>DMZ ................................................................................................................................................................ 62 5.3 Basic>UPnP ................................................................................................................................................................ 63 5.4 Basic>Dynamic DNS.................................................................................................................................................. 64 5.5 Basic>VPN Passthrough ............................................................................................................................................. 65 6 Reference Manual .......................................................................Error! Bookmark not defined. 6.1 Advanced>MAC Filtering .......................................................................................................................................... 67 6.2 Advanced>IP Filtering ................................................................................................................................................ 68 6.3 Advanced>Port Forwarding ........................................................................................................................................ 70 6.4 Advanced>Port Trigger ............................................................................................................................................... 71 6.5 Advanced>Layer 7 ...................................................................................................................................................... 73 6.6 Advanced>URL Filtering............................................................................................................................................ 74 6.7 Advanced>ACL Filtering............................................................................................................................................ 75 6.8 Advanced>Static Routing ........................................................................................................................................... 78 7 Reference Manual .......................................................................Error! Bookmark not defined. 7.1 Wi-Fi> Basic ............................................................................................................................................................... 80 7.2 Wi-Fi> Advanced ........................................................................................................................................................ 81 7.3 Wi-Fi>WPS ................................................................................................................................................................ 83 Issue 01 (2015-07-10) Huawei Proprietary and Confidential iii Copyright © Huawei Technologies Co., Ltd. .1 Prerequisite Skills and Knowledge 1. .2 Conventions Used in this Document 1. Important information that should be observed. Failure to observe this may result in damage. it could be used to configure the CPE settings through the web browser by user"s PC. and should understand related local building codes. 1. 1. Ltd. 1 About this Guide About This Chapter This document provides information and procedures on the installation and configuration of LTE Outdoor CPE. Network administrators should have a solid understanding of software installation procedures for network operating system and troubleshooting knowledge. Please refer to the following pages for more detail. LTE Outdoor CPE has a web GUI which supports http/https protocol. You could utilize the information in this guide to set up your device.2 Conventions Used in this Document The following typographic conventions and symbols are used throughout this document: Very important information. you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures. Additional information that may be helpful but not required. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 1 Copyright © Huawei Technologies Co. In addition. you should be familiar with the following: Hardware installers should have a working knowledge of basic electronics and mechanical assembly.1 Prerequisite Skills and Knowledge To use this document effectively. bold Menu commands. buttons and input fields are displayed in bold Issue 01 (2015-07-10) Huawei Proprietary and Confidential 2 Copyright © Huawei Technologies Co. . Ltd.. 4 LED Indicators 2. Ltd.2 Product Package 2..5 Installation 2. . 2 Introduction About This Chapter 2.1 Product Overview LTE Outdoor CPE is an all-in-one device that integrates TD-LTE Support TD-LTE Support 3GPP Release 10 compliant Support 1TX/2RX with TX switched diversity (LTE) Support LTE UE Category 4 Support 2 LAN ports and 1 VoIP port Support HTTP/HTTPs Web GUI 2.3 Connectors 2.1 Product Overview 2.2 Product Package Item Q'ty 1 LTE ODU CPE 1 2 PoE Box 1 3 User Manual 1 4 Power Adapter 1 5 Plug 1 Issue 01 (2015-07-10) Huawei Proprietary and Confidential 3 Copyright © Huawei Technologies Co. Item Q'ty 6 Mount Kit 1 7 Ground Cable 1 If any item of mentioned above is missing or damaged. IDU Rear Panel IDU Front Panel Issue 01 (2015-07-10) Huawei Proprietary and Confidential 4 Copyright © Huawei Technologies Co.. . 4. One RJ-45 connector for connecting to the IDU WAN port. LED indicator inside. One SIM card slot for inserting SIM card. please contact our customer support immediately. 2. Ltd. A grounding screw on the rear panel.3 Connectors The Outdoor LTE CPE has following connectors (from left to right): 1. 2.. 3. LED name Location Color LED Behavior Status Indication LED list . Ltd.4 LED Indicators ODU LED Indicators as following:. . - Main Power Blue ON Power On Blinking Factory Reset OFF Power Off Ethernet Status Yellow Steady ON Ethernet connected Blinking Upgrading OFF No Ethernet action SIM status Green Steady ON SIM Detected Blinking when On-hook PUK / PIN Code OFF No SIM Detected Issue 01 (2015-07-10) Huawei Proprietary and Confidential 5 Copyright © Huawei Technologies Co. .2.. .4G WiFi 5 WLAN_2G Green Blinking Data transmition Off Disable 2. Ltd. .4G WiFi On Enable 5G WiFi 6 WLAN_5G Green Blinking Data transmition Off Disable 5G WiFi On Registered 7 Phone (VoIP) Green Blinking Busy Off De-registered Issue 01 (2015-07-10) Huawei Proprietary and Confidential 6 Copyright © Huawei Technologies Co. each LED indicates each link status 4G-Signal Blue Chasing light Searching Blue Blinking Network Entry 4G-1 Blue Steady ON SINR < 0dB 4G-2 Blue Steady ON 0dB ≦ SINR < 4dB 4G-3 Blue Steady ON 4dB ≦ SINR < 9dB 4G-4 Blue Steady ON 9dB ≦ SINR < 16dB 4G-5 Blue Steady ON 16dB ≦ SINR IDU LED Indicators as following: Number LED name Color LED Behavior Status Indication Green On Power On 1 Main Power Off Power Off Green On System is booting 2 System Blinking System is upgrading Off System is disabled Display signal Strength 1 LED: SINR< 0dB 2 LEDs: 0dB <=SINR< 4dB LTE Signal On 3 Green 3 LEDs: 4dB <=SINR< 9dB Strength 4 LEDs: 9dB <=SINR< 16dB 5 LEDs: 16dB <=SINR Off No signal Blinking Ethernet connected 4 LAN 1 & 2 Green Off No Ethernet connected On Enable 2.LED name Location Color LED Behavior Status Indication 4G Status LED : Link Status When CPE is power on. Step 2: Before Mounting the Device 1. are licensed by the appropriate government regulatory authorities should install outdoor units and antennas. Insert power plug to the power adapter and then plug in power adapter to DC 56V port of IDU. B.. (Suggest to with Ethernet lighting protector between Ethernet cable and indoor PoE supplier for better lighting and surge protection). Only experienced installation professionals who are familiar with local building and safety codes and. Must connect a Grounding cable between the ground terminal of the ODU (marked ) and a ground connection. Step 1: Selecting a Location The ODU should be pole-mounted outdoors and aligned so its antenna faces the nearest LTE base station. verify that you have all the items listed in the package checklist. 3. One RJ-45 connector for connecting to the ODU to IDU C. Make sure the grounding screw on the rear panel. Be sure to ground the ODU with an appropriate grounding wire by attaching it to the grounding screw on the unit and to a good ground connection. If any of the items is missing or damaged. E. it is recommended to use a lightning arrestor immediately before the Ethernet cable enters the building. A. For additional lightning protection. contact your LTE service provider. . 2. D. F. where applicable. contact your service provider. Please check below items before installing the outdoor device. LED indicator inside and SIM card slot for inserting SIM card. consider these guidelines: 1. When selecting a suitable location for the unit. Make sure the ODU is turned off and NO PoE supply connected before you insert SIM card or it may damage your SIM card.5.2. 4.5 Installation Before installing the LTE outdoor CPE. Place the ODU away from power and telephone lines. 2. 2. Avoid placing the ODU too close to any metallic reflective surfaces.1 Installing LTE Outdoor CPE Any of the items are missing or damaged. To connect with Grounding cable Issue 01 (2015-07-10) Huawei Proprietary and Confidential 7 Copyright © Huawei Technologies Co. Ltd. Place the ODU as high as possible to achieve the best possible link quality. 3. (e and f) Issue 01 (2015-07-10) Huawei Proprietary and Confidential 8 Copyright © Huawei Technologies Co. Step 4: Mounting the Device: Installing Pole Mount 1. (a. Ltd. Gently twist the body into the ODU. Tighten the nuts. Thread the M8*23mm bolts through a spring washer. 4. Make sure that the connector is completely inserted and tightened. Tighten the locking mechanism of mental strap by screwdriver. (a) 2. b. Remove the sealing gland plug from the gland nut. 5. flat washer and ODU. (d) 5. and d) 4. (a and b) 3.. 2. Lossen the locking mechanism of mental strap by hand or screwdriver. Insert the cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the ODU. Do not disassemble the gland base from the bracket. Open the sealing gland nut and remove it. . labeled. Insert the rubber bushing on the cable into the gland base. Attach the Pole-Mount bracket to the other side of the pole. Step 3: Connect the cable with waterproof node 1. Wrap the metal strap with Pole-Mount Bracket. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 9 Copyright © Huawei Technologies Co. Wrap the metal strap with Pole-Mount Bracket. Connect the Ethernet cable to the RJ45 ports of IDU and ODU. Ltd. 2.168. The PWR LED shines a steady green when device ready.1. Open a web browser and go to https://192. Tighten the nuts.xxx (xxx: 2-254). 1.1. flat washer and ODU. Connect the supplied power adapter to the IDU. Mounting the Device. Tighten the locking mechanism of mental strap by screwdriver. Lossen the locking mechanism of mental strap by hand or screwdriver. b. and d) 4.. Insert a USIM in ODU (SIM card slot). 5. Attach the Pole-Mount bracket to the other side of the pole.5. Insert a USIM in ODU(SIM CARD SLOT). (d) 5. (a and b) 3. 3. PC will get default IP 192.1. 5. Use power adapter to connect IDU(Power) 4.2 Connecting the Cable Step 1: Physical connection as following 1. Step 2: Installing Pole Mount 1. Connect IDU(WAN) and ODU(RJ45) via Ethernet cable. Thread the M8*23mm bolts through a spring washer. (a. 3.168. 2. . (a) 2. (e and f) Step 3: Connect to the Internet Physical connection is as following (Refer to Installing Device Instruction). Connect IDU(ETHERNET PORTS) and PC via Ethernet cable. 2. Connect the Ethernet cable from the computer to one of the IDU’s Ethernet Ports 4. Otherwise.. Ltd. . Use ONLY the PoE Box which supplied with the ODU. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 10 Copyright © Huawei Technologies Co. LTE Outdoor CPE may be damaged. the device would request addition Identify Code to protect any illegal Hacker attack.1 Login to Web-GUI 3.168. which is: http://192. 3 Web Interface About This Chapter 3. .1/ Step 2: Enter the user login credentials to access web management interface. Default Log-in information: Username: user Password: ●●●●●● Log-in protection: If you key-in the log-in username or password error more than three times.3 Status and device information 3. You can press re-fresh button to re-fresh the identify code if it is hard to read..1. Ltd.2 Function Button 3.1 Login to Web-GUI Step 1: Open the Web browser and enter the default IP address of the device. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 11 Copyright © Huawei Technologies Co.4 Menu Structure 3. please go Management>Setup Wizard or Management>Wi-Fi setup to change the Wi-Fi password.. NOTE We recommend you to change the default Wi-Fi password while the first time log-in. . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 12 Copyright © Huawei Technologies Co. Ltd. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 13 Copyright © Huawei Technologies Co. you can go Management>Modem Setup>Connection Mode to set up. LOGOUT Quickly log out the device.3. device will back to log-in page RECONNECT/DISCONNECT Let the LTE device reconnect or disconnect to WAN.. Ltd. REBOOT Force device to initial a reboot. This reconnect and disconnect is related to connection mode configuration. .2 Function Button (Disconnect) (Reconnect) Function button is located at each Web UI page Top-Right corner. . when the device is connected it will display DISCONNECT icon for you to manual disconnect it. it will display RECONNECT icon If device is on the Manual connection mode. Ltd.. NOTE If device is on the Auto connection mode. when the device is disconnect it will display RECONNECT icon Issue 01 (2015-07-10) Huawei Proprietary and Confidential 14 Copyright © Huawei Technologies Co. N/A: VPN is not connected yet. Otherwise it is N/A Issue 01 (2015-07-10) Huawei Proprietary and Confidential 15 Copyright © Huawei Technologies Co. VPN Status– Layer2 It shows the Layer2 VPN connection status. You can refer to below column for detail definitions. Ltd. Data/VoIP IP Connection – Dual mode (On/Off) value is depends on if the Data or VoIP connection is available or not. when connected it will display the VPN client IP address. Connection Mode The mode to obtain IP address. IP Connection – Single mode (On/Off) value is depends on if the WAN connection is available or not. Otherwise it is N/A Data/VoIP IP Address – Dual mode For DHCP mode . There are three options: Gateway/VPN-L2TP(Tunnel Layer 2 or Layer 3)/Router Please go Management>WAN Setup to configure it. Operation Mode The mode to forward data packets between Internets.3 Status and device information 3.IP address acquired on the Data/VoIP WAN interface is displayed. .IP address acquired on the WAN interface is displayed. Connected: VPN is connected/ N/A: VPN is not connected yet. here displays the current status of the device such as system uptime and WAN information.3. Available options: DHCP/ Static. VPN IP Address – Layer3 It shows the Layer3 VPN connection status..1 Status> Device Status This page is information only.3. IP Address– Single mode For DHCP mode . 2. there are three default configurations for you to select: Low/Medium/High or you can select Custom to configure by your preference. DMZ DMZ enabled or disabled.4GHz WiFi 2. Device Restart Reason The reason for last device reboot (e. DDNS DDNS enabled or disabled. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 16 Copyright © Huawei Technologies Co. Firewall Here displayed your current firewall level. . − Click the "Auto" button auto update the current status.4GHz WiFi DNS Server The Domain Name Server address. Ltd. − Click the "Refresh" button manual update the current status. For more detail please refer to Basic> Firewall section. if there is any 5GHz WiFi 5GHz WiFi Time Server The NTP (Network Time Protocol) server address. UPnP UPnP enabled or disabled.. Device Up Time The duration since the unit is powered on in format "x day(s) <hour>:<minute>:<second>".g. Software Upgrade). Issue 01 (2015-07-10) Huawei Proprietary and Confidential 17 Copyright © Huawei Technologies Co. Connection Time Time during which the unit is connected to the eNB or base station..e. 3. . PLMN Public Land Mobile Network identity.2 Status> Modem Status The Modem Status displays a summary of the LTE network connection parameters .The information includes: Network Current active network mode i. LTE Connection Status The status of modem connection. Roaming Status Informs current roaming status.3. Ltd. 5dBm unit. RSRP Reference Signal Received Power 1dBm unit.. Uplink current speed Uplink data rate. Uplink/Downlink Traffic Displays the current accumulate Downlink/Uplink traffic. Ltd. PUK Retries The remained PUK retry count. Downlink current speed Downlink data rate. IMSI International Mobile Subscriber Identity. . PCI Issue 01 (2015-07-10) Huawei Proprietary and Confidential 18 Copyright © Huawei Technologies Co. You can reset by press the ”Clear Traffic” button in right. SINR Signal to Interference plus Noise Ratio (dB). Minimum: -141. Minimum: -141. PIN Retries The remained PIN retry count. Minimum: -40. USIM Status SIM card status information. RSRQ Reference Signal Received Quality 0. Operator Name Current connected operator name. RSSI Received Signal Strength Indication 1dBm unit. − Click the "Auto" button auto update the current status. Current Band Current connected Band(According to 3GPP defined) − Click the "Refresh" button manual update the current status. . you can go Management>Modem Setup to setup the Single APN Data / VoIP APN Status – Dual mode Displayed the connect status (Success /Fail / N/A) of Dual APN . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 19 Copyright © Huawei Technologies Co. Ltd.. you can go Management>Modem Setup to setup the Dual APN. Pre-coding Control Indication CQI Channel Quality Indication APN Status – Single mode Displayed the connect status(Success /Fail / N/A) of Single APN . Model ID Device model name. 5 GHz Wi-Fi MAC 5GHz Wi-Fi MAC address. Hardware Version Device HW version.3. If you want switch the call please press “flash” key on your telephone. This information also can be observing on the front panel voice line LED. Status Registered or De-registered in the SIP server.4 Status> About This page displays the device default necessary information. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 20 Copyright © Huawei Technologies Co.3.3. 2. . and terminate multimedia sessions such as Internet telephony calls (VOIP). The account format depends on the SIP Server. IMEI International Mobile Equipment Identity number.3 Status> Telephony Status SIP User IP Address IP address of the Session Initiation Protocol (SIP). Those values are set by the manufacturer as the factory defaults. modify. Ltd. Account The SIP Account. Service Provider Your network and service operator. 3. an application-layer control protocol that can establish. You can go Management>Telephony to change the setting Disable/Enable. Product Name Product type..4GHz 2.4GHz Wi-Fi MAC address. Call Waiting Allow the second caller to wait on-line while an existing phone call is on-going. 3.4 Menu Structure After entering "Detailed Configuration Page".) Users can refer to the menu structure given below: Status Device Status Modem Status Telephony Status About Help Management Setup Wizard Modem Setup WAN Setup LAN Setup IPv6 Telephony Diagnostics System Log Issue 01 (2015-07-10) Huawei Proprietary and Confidential 21 Copyright © Huawei Technologies Co. the user can quickly jump to the specified Sub Menu.pdf to guide you how to operate this device in detail.. Ltd. (By clicking "Quick Panel" at the bottom of the page. 3. . Indoor Unit Serial Indoor device’s serial number.3.5 Status> Help While you press the Help you will be direct to download a . Number Chip Version Device Chip version. Number Outdoor Unit Serial Outdoor device’s serial number.Software Version Device SW/FW version. . Personalization PIN Management Configuration Device Setup Software Basic Firewall DMZ UPnP Dynamic DNS VPN Passthrough Advanced MAC Filtering IP Filtering Port Forwarding Port Trigger Layer 7 URL Filtering ACL Filtering Static Routing WiFi Basic Advanced WPS Issue 01 (2015-07-10) Huawei Proprietary and Confidential 22 Copyright © Huawei Technologies Co. Ltd. . if no problem.1 Management 4. Selection your locate country. and check if your location have daylight saving. − Click the "Next" button to launch the Setup Wizard. − Step 1: By press the “Next” button to start Wizard. we will guide you to set up your Time zone.4 Advanced 4.4GHz and 5GHz Wi-Fi network name/Encryption and Wi-Fi Password.5 WiFi 4. − Step 3: Set up your 2. 2.1 Management 4.1 Management >Setup Wizard The Setup Wizard will guide you to do the important setting of the device. then press “Next”. . − Step 2: 1.3 Basic 4. Review all your settings. 4 Reference Manual About This Chapter 4. please press “Next”. − Step 4: Check your settings and again then press “Save” button to apply the change.. − Click the "Save" button to save any modified settings. Ltd. NTP server and location time zone.2 Personalization 4.1. − Click the "Previous" button to go back to the previous page − Click the "Cancel" button to return to the first page. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 23 Copyright © Huawei Technologies Co. . .Issue 01 (2015-07-10) Huawei Proprietary and Confidential 24 Copyright © Huawei Technologies Co. Ltd. . Ltd. .Issue 01 (2015-07-10) Huawei Proprietary and Confidential 25 Copyright © Huawei Technologies Co. Password: Key-in the password for the APN if there is any.2 Management>Modem Setup In this page.1. APN mode: Single/ Dual You can configure your APN as single or dual. this information should provide by your service provider. the second APN (VoIP APN) will be editable. you can configure all the network related parameters. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 26 Copyright © Huawei Technologies Co. only when you select the dual APN. Connection Mode: Set connection as Auto or Manual.4.Roaming to other network operator is enabled. which your service provider gave you User Name: Key-in the user name for the APN if there is any. this information should provide by your service provider. VoIP APN APN Setting: Auto . this information should provide by your service provider. Disable . APN Setting Setting how APN (Access Point Name) is assigned. Auto Mode: Device will continuously try to connect network automatically. Roaming Setting Enable/Disable roaming to other network operator.Device will automatically choose the default APN setting Manual –Manually enter the Data APN of your network.Roaming to other network operator is disabled. Enable . if you failed to connect to network.. Data APN APN Setting: Auto . Ltd. Password: Key-in the password for the APN if there is any.Device will automatically choose the default APN setting Manual –Manually enter the VoIP APN of your network. Manual Mode: You have to manual press the Reconnect button to re-connect to network every time. this information should provide by your service provider. which your service provider gave you User Name: Key-in the user name for the APN if there is any. . Click Apply to activate your changes Single mode Dual Mode Issue 01 (2015-07-10) Huawei Proprietary and Confidential 27 Copyright © Huawei Technologies Co. . . Ltd. Click Undo to clear the changes that you have made to this window.. . 1. − GRE GRE Type: Layer 2 Tunnel Destination IP: Please input VPN tunnel’s Destination IP address MTU Size: Enter the value for transmission unit size (Range: 576-1500). .3 Management>WAN Setup Operation Mode It displays the mode how to forward data packets between Internet and Intranet. GRE Type: Layer 3 NAT Support: Enable: Enable to let the inner source IP to do the NAT Disable: Disable to let the inner source IP bypass the NAT Tunnel Interface IP: Please input the VPN tunnel’s IP address Tunnel Interface Mask: Please input the VPN tunnel’s IP subnet mask Tunnel Destination IP: Please input VPN tunnel’s Destination IP address MTU Size: Enter the value for transmission unit size (Range: 576-1500). in the gateway mode the SNAT is enabled.4. BCP: Disable: You can perform the L3 VPN connection NAT Support: Enable: Enable to let the inner source IP to do the NAT Disable: Disable to let the inner source IP bypass the NAT Internet IP Address: The VPN IP address server that you want to connected to. you need go Advance->Static Routing to add the routing rule of the VPN section. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 28 Copyright © Huawei Technologies Co. Enter the value for transmission unit size (Range: 576-1500). Gateway Mode: The mode to obtain IP address for the device. Internet IP Address: The VPN server IP address that you want to connect to. Username: The user name of your VPN account Password: The password of your VPN account Host Name: If server requests the item. this device support L2TP and GRE − L2TP BCP: Enable: You can perform theL2 VPN connection. need to fill in MTU Size: Enter the value for transmission unit size (Range: 576-1500). NOTE If you select the Layer 3 VPN. − MTU Size: Set the WAN maximum transmission unit (MTU) size in bytes. need to fill in MTU Size: Enter the value for transmission unit size (Range: 576-1500). VPN Mode: VPN Type: You can select your VPN type. Ltd. Username: The user name of your VPN account Password: The password of your VPN account Host Name: If server requests the item.. sothatfirewall function (i. Router Mode: When device is set as router mode: the SNAT (source NAT) will be disabled. . port forwarding) will not applicable. . − MTU Size: Sets the WAN maximum transmission unit (MTU) size in bytes. Ltd. Click Apply to activate your changes Issue 01 (2015-07-10) Huawei Proprietary and Confidential 29 Copyright © Huawei Technologies Co. DMZ. Click Undo to clear the changes that you have made to this window.e.. . Enter the value for transmission unit size (Range: 576-1500). Ltd. ..Issue 01 (2015-07-10) Huawei Proprietary and Confidential 30 Copyright © Huawei Technologies Co. ..Issue 01 (2015-07-10) Huawei Proprietary and Confidential 31 Copyright © Huawei Technologies Co. Ltd. In the DHCP Server page you set DHCP parameters for dynamic IP assignment. MAC Address Add a device MAC address. DHCP Server: The unit has a built-in DHCP server that can be used for managing the distribution of IP addresses for the devices connected to the local LAN port (Ethernet or Wi-Fi) and Web UI.1. how long you want to renew the IP.168.options are :Disable. − DHCP Lease Reservation The Lease Reservation page displays information on reserved IP addresses for leasing. DHCP Lease Time Set the time. You can also add.4. Relay Disable: The device will not assign LAN IP address to PC. you need to manually configure the IP addresses of the computers and other LAN devices. the default value is 192. delete. Select Select an IP to delete.1.4 Management>LAN Setup In this page. DHCP Ending IP Address Enter the last IP address assigned by the DHCP server. DHCP Starting IP Address Enter the first IP address assigned by the DHCP server.. Enable DHCP Server Select this check-box dynamically assigns a leased IP address to clients that connect to the device from the local network. or modify the reservation settings. you can change the Web UI and device local IP address distribution range. . In this page you assign the specific IP addresses to the specific client device connected to the Ethernet ports and Wi-Fi access point. IP Address Issue 01 (2015-07-10) Huawei Proprietary and Confidential 32 Copyright © Huawei Technologies Co. Server. DHCP Server IP Address Enter a DHCP server IP address.1 − DHCP Service Type: Please select the DHCP service type . you have to manually set static IP address to the connected PC to access the UI. If you select Disable. Ltd. Host Name Enter a name to the host. − LAN IP Address: Please input the LAN IP address here. Specify a reservation IP address for a specified MAC address. Enabled Select if to enable or disable a specified IP setting. − DHCP Lease Status The Lease Status page displays information regarding the leased IP address(es): This is display the connected PC name which connected to the Client Host Name LTE device. This is display the connected PC MAC address which connected MAC Address to the LTE device. This is display the IP address that assigned to this LAN device(Host IP Address PC) Remaining Lease This display how many seconds remain for this assigned IP, Duration Block: To Block the specific PC, after press the“Block” button the LAN device cannot access this LTE device any more. Unblock: Press “Unblock” button to allow the LAN device to back to Action connect again. This function is for you to easily manage the LAN devices, to avoid the unexpected device access from your LAN. Status This shows the current IP assignment availability. DHCP Relay: DHCP Relay Agent DHCP Relay Server IP Address: The device will request IP address from the DHCP Relay server, please input the DHCP relay Server’s IP address for obtain the IP address. If you input wrong DHCP Relay server IP address or Relay server is not working, please manually set static IP address to the connected PC to access the UI. - - Use the Add or Delete buttons to add or clear reserved IPs for leasing, please click Apply button to confirm the Add or Del. - Click Undo to clear the changes that you have made to this window. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 33 Copyright © Huawei Technologies Co., Ltd. - Click Apply to activate your changes. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 34 Copyright © Huawei Technologies Co., Ltd. 4.1.5 Management>IPv6 Enable IPv6 This is a check box, please checked to enable the IPv6address or un-check to disable it. WAN Setting: − IPv6 Type: You can assign the how to get IPv6 address here, there are two options: static/auto configuration. Auto configuration: The device will get IPv6 address automatically. Enable DHCP-PD: Checked the checkbox to enable the DHCP-PD server to allow the server assign the prefix the client DNS: You can define the DNS as Auto or Manual DNS1: Please input the IPv6 DNS server DNS2: Please input the IPv6 DNS server if there is any. LAN Setting: Auto-configuration type: Disable, SLAAC DHCPv6, SLAAC RDNSS, Stateful DHCPv6 Disable: Disable the IPv6 address assignment for LAN client. SLAAC DHCPv6: (Stateless Address Auto-configuration DHCPv6), Router Advertisement (RA) will contain the IPv6 Prefix and default gateway information and DHCP v6 will provide DNS address and other network information. This method of LAN IP assignment will recommend to use at private area due to it is with lower security level. -IPv6 SLAAC DHCPv6 RA Lifetime(seconds): The IP address will reset after X seconds, default is set as: 3600 sec Issue 01 (2015-07-10) Huawei Proprietary and Confidential 35 Copyright © Huawei Technologies Co., Ltd. SLAAC RDNSS: (Stateless Address Auto-configuration +Recursive DNS Server),Router Advertisement (RA) will regularly broadcast the multicast package and the Client will get Prefix, default gateway and DNS information, the Client will combine the Prefix and auto-generate the Host ID as the device’s IPv6 address. -IPv6 SLAAC RDNSS RA Lifetime(seconds): The IP address will reset after X seconds, default is set as:3600sec Stateful DHCPv6: RA only contain the default gateway information, the other information like IPv6 Prefix ,Host ID and DNS IP address is assigned by DHCPv6; DHCPv6 will record all the LAN IPv6 address, MAC list and regularly maintain the IPv6 address record. If you are in the public area, we will recommend using stateful DHCv6. -IPv6 Address Pool Start: Defined the IPv6 address start point, default is: 1 -IPv6 Address Pool End: Defined the IPv6 address end point, default is: 200 -IPv6 Address Lifetime(seconds):The IP address will reset after X seconds, default is set as: 3600 sec - Click Undo to clear the changes that you have made to this window. - Click Apply to activate your changes. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 36 Copyright © Huawei Technologies Co., Ltd. . Ltd.Issue 01 (2015-07-10) Huawei Proprietary and Confidential 37 Copyright © Huawei Technologies Co. . . Ltd. .Issue 01 (2015-07-10) Huawei Proprietary and Confidential 38 Copyright © Huawei Technologies Co. Before using the VoIP Phone ports on the unit. Password The SIP user Password. Server account (Session Traversal Utilities for NAT)STUN is a standardized.1. STUN Server IP address or domain name of the STUN Server. please checked to enable the VoIP function or un-check to disable VoIP. please always double confirm your service provider. it helps bypassing the restrictions imposed by your Internet provider.6 Management> Telephony This chapter describes how to configure VoIP parameters. Enable VoIP This is a check box. for the outgoing Display Name call the receiver will see your Display name as Caller ID (if supported by the SIP server). Password Confirm Enter the SIP user Password again. Ltd. To change the settings below. Enable STUN It also enables the application to determine the public IP addresses allocated to it by the NAT. You can make VoIP calls by connecting a regular phone to the unit's Phone ports. like any proxy server. Voice over Internet Protocol (VoIP) technology is a way of using the Internet to make phone calls. − Account User account The SIP (Session Initiation Protocol) User name. A SIP Outbound Proxy acts. Enter the name that will be displayed as your ID/number. . Its format depends on the SIP Server.4. Listening on an Outbound Proxy unblocked port number and forwarding requests between SIP client and Address your VoIP provider.. you must have an account with a SIP service provider. Its format depends on Username the SIP Server. Registrar Address SIP server IP address Registrar Port Port number of the SIP Server. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 39 Copyright © Huawei Technologies Co. Attention VoIP doesn’t support “flash + number” feature. light-weight protocol that allows an application to discover the presence and types of NATs and firewalls between itself and the public Internet. User Account The SIP Account. Address User Domain This LTEDevice’s domain name. When you hang up the call for x seconds the call will be really dropped.5 seconds.This dial plan is for the speed dial “|” represent or.T : ” x” represent any number(0~9) . Call Waiting TimeOut Enter a number of seconds after which the call waiting is timed out. the Register message is sent to the Outbound Proxy.” x “represent any number (0~9). Ring Tone TimeOut Set how long you want the ring tone exist. you can press the flash key on the telephone to switch the call. T is just a symbol means end number. You didn’t need to key-in anything to end the dial. if you don’t want to wait for 3sec. just wait dial time out (3sec). (Please enter 0 ~ 5 seconds). please insert the same number in Start/End field. Otherwise. For example. if your VoIP service Start provider gave you this information.2 ~ 1. and the phone number 1111 would be dialed immediately. the action will be ignored. keep the default values. (Please enter 15 ~ 60 seconds) Delay Time After On Hook Set a really hang up delay time. The device support two dial plans: ✽xx : “✽”represent the asterisk key on the phone. you can set several dial plan but separate them by |. just set the dial plan as: xx. Call Feature Settings Call Waiting Enables or Disable the second caller can wait on line while you are on the call. End IF you only have one port for listening RTP.#. . which forwards it to the Registrar. If both an Outbound Proxy and a Registrar are configured. “..” means arbitrary number of digits . Port RTP Port Range Enter the listening start port number(s) for RTP traffic. Ring Back Tone You can determine the ring tone sound here Frequency Quota: Issue 01 (2015-07-10) Huawei Proprietary and Confidential 40 Copyright © Huawei Technologies Co. keep the default values. Call Hold Enables or Disable the Call Hold function The Call Hold function is allow you to hold current call by press the flash key on the telephone Dial Plan A dial plan is a set of rules used for determining whether a complete set of numbers has been entered for the IP address of SIP server. you could dial 1111#. Ltd. xx. Otherwise. (Please enter 0. if your VoIP service RTP Port Range provider gave you this information. Outbound Proxy The number of the Port on which the outbound Proxy listens. Enter the listening end port number(s) for RTP traffic. Max Flash Time Set the max Flash key press time. if you press the Flash key over x seconds define in the column. The device supports to set 1 or 2 frequency. please enter 0~4 seconds or asterisk (*) to set continue on) Ring Back Tone Off Set ring back tone off for how long in a ring tone cycle. The device supports to set 1 or 2 frequency. Ring Back Tone On: Set ring back tone continues for how long in a ring tone cycle. Real Number: Please correctly fill-in the real dial number here.#. this column is only allow to key-in: numbers 0~9. you can have maximum speed dials. the value should between 300~800 Hz. this column is only allow to key-in: numbers 0~9 . Ring Back Tone On: Set ring back tone continues for how long in a ring tone cycle. You can set the ring tone frequency here. . Ltd.The device supports to set 1 or 2 frequency. the value should between 300~800 Hz. please enter 0~4 seconds or asterisk (*) to set continue on) Ring Back Tone Off Set ring back tone off for how long in a ring tone cycle. please enter 0~4 seconds or asterisk (*) to set always off) Speed dial Please pre-set the mapping table for speed dial. please enter 0~4 seconds or asterisk (*) to set always off) Call Waiting Tone You can determine the call waiting tone sound here Frequency Quota: You can set the call waiting tone frequency here. Ring Back Tone On: Set ring back tone continues for how long in a ring tone cycle.* Issue 01 (2015-07-10) Huawei Proprietary and Confidential 41 Copyright © Huawei Technologies Co.. please enter 0~4 seconds or asterisk (*) to set continue on) Ring Back Tone Off Set ring back tone off for how long-in a ring tone cycle. the value should between 300~800 Hz. please enter 0~4 seconds or asterisk (*) to set always off) Busy Tone You can determine the busy tone sound here Frequency Quota: You can set the busy tone frequency here. please enter 0~4 seconds or asterisk (*) to set always off) Dial Tone You can determine the dial tone sound here Frequency Quota: You can set the dial tone frequency here. please enter 0~4 seconds or asterisk (*) to set continue on) Ring Back Tone Off Set ring back tone off for how long in a ring tone cycle. Ring Back Tone On: Set ring back tone continues for how long in a ring tone cycle. . The device supports to set 1 or 2 frequency. the value should between 300~800 Hz. Dial Number: Please define the speed dial number. Pick up Phone-1. 3.Call Feature Procedure (Example) 1. Dial tone should be presented. Pick up Phone-3.. 5. 1. Make sure the Call Hold is enabled. Dial the number of Phone-1. Verify that the Phone-3 presents the ring back tone. Dial tone should be present.9s on Phone-1 UI. . Phone-2 should ring and Phone-1 Caller Name should present ring back tone. Pick up Phone-2. Call Hold 4. the call should be retrieved (i. Phone-2 presents the call waiting tone. 3. Dial the number of Phone-2. 2. Press Flash button on Phone-2. Phone-2 should ring and Phone-1 should Caller ID present ring back tone. Pick up Phone-2. Pick up Phone-1. Call should be established between Phone-2 and Phone-3. Pick up Phone-1. Dial tone should be presented in Phone-3. Phone-1 should ring and Phone-2 should present ring back tone.e. 1. 3. Attention. 8. Enable the Call Hold on web UI. Dial tone should be presented in Phone-3. Dial the number of Phone-2 from the Phone-3. 6. Set Max Flash Time to 0. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 42 Copyright © Huawei Technologies Co. Pick up Phone-1. 1. Ring back tone should be stopped in Phone-2 and bi-directional voice traffic should flow. Dial tone should be presented 2. Dial the number of Phone-2 from the Phone-3. Dial the number of Phone-2. Disable the call waiting on web UI. When Phone-2 press Flash button. Enable the Call Waiting on web UI. Dial tone should be presented. Ltd. If Phone-2 presses the Flash button again. 2. 2. Phone-1 is taken off hold) 1. 3. 6. 6. Phone-2 could use the Flash button to switch to the other call 1. Call Waiting 7. 5. 4. Phone-3 presents the busy tone and there is no disturbances between phones-1 and Phone-2. 7. Pick up Phone-2. 2. Pick up Phone-1. Phone-2 should ring and Phone-1 should present ring back tone. Max Flash Time 1. 4. Ring back tone should be stopped in Phone-1 and Waiting bi-directional voice traffic should flow. Cancel Call 4. 2. Dial the number of Phone-2. Dial tone should be presented. The caller Name (display Name) of Phone-1 should be displayed in the screen of Phone-2. Configure the display Name of Phone-1 on web UI. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone. 5. Phone-1 should be held. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow. The caller ID(phone number) of Phone-1 should be displayed in the screen of Phone-2. 3. Pick up Phone-3. 2. Pick up Phone-3. Dial tone should be presented. Phone-2 should ring and Phone-1 should present ring back tone. Make sure the Call Hold is enabled. Ltd. Ring back tone should be stopped in Phone-1 and Blind Call Transfer two-way voice should be presented. 6. . 5. 3. Pick up Phone-2. Phone-1 will presents the busy tone after 30 seconds. 1. Each phone should be able to hear the speech of other phones. Pick up Phone-1. 1. Attended Call 2. On Hook 4. Phone-2 presents the busy tone after 1 second. Dial tone should be presented. Phone-3 should start ringing and Phone-2 hang up. After all three phones in the conference call. 1. the all call should be disconnected. Set Delay Time After On Hook to 1s on Phone-1 UI 2. On hook the Phone-1. Press Flash button on Phone-1 and 0. Make sure the Call Hold is enabled. Dial the number of Phone-2. 5. Phone-2 presses the Flash button and all three phones will be in Three Way conference call. Phone-2 presses the Flash button and make a phone call to Phone-3 and make sure the call is established between Phone-2 and Phone-3. Pick up Phone-2. another call (Phone-2 with Phone-3 or Phone-2 with Phone-1) should still exist. 4. Phone2 should ring and Phone-1 should Delay Time After present ring back tone. 3. Press Flash button on Phone-1 6. 1. Dial tone should be presented. Dial the number of Phone-2. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 43 Copyright © Huawei Technologies Co. Make a phone call from Phone-1 to Phone-2 and make sure the call is established between Phone-1 and Phone-2. Transfer 3. Pick up Phone-1. Phone2 should ring and Phone-1 should Ring Tone TimeOut present ring back tone. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow. 4. Phone-2 press the Flash button followed by the number of Phone-3. 3. Dial tone should be presented. Phone-2 presents the hold tone. 2.. Make sure the Call Hold is enabled. Dial the number of Phone-2. 4. Phone2 should ring and Phone-1 should present ring back tone. Pick up Phone-2. Attention: If we hang up the Phone-1 or Phone-3. 2. Don’t pick up Phone-2. Set Ring Tone TimeOut to 30s on Phone-1 UI. Pick up Phone-1. 7. There should be a call setup between Phone-1 and Phone-3 with voice pass through.9 second later. Dial Tone should be presented. Dial the number of Phone-2. 2. 3. 4. Conference Call 5. If we hang up the Phone-2. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone. Pick up Phone-1. Pick up Phone-1. 1. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow. 3. 5. Set Real Number to 9887872 on Phone-1 UI. the tone is depend on your settings. Hang up the Phone-2 8. Busy Tone 3. Set a rule on Phone-1 UI. Dial the number of Phone-2. Phone2 should ring and Phone-1 should present ring back tone. Every phone number need to follow dial plan’s rule. Pick up Phone-1. Pick up Phone-1. Set a rule on Phone-1 UI. The call is established between Phone-2 and Phone-3 7. Pick up Phone-1. Dial tone should be presented in Phone-3. Pick up Phone-1. Set Dial number to 123 on Phone-1 UI. 2. Dial tone should be presented. 3. 2. Phone-2 should ring. Ring back should be stopped in Phone-1 and two-way voice should be established. Dial the number of Phone-2. 3.T>: 12. . <*xx>: *12. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow. Dial the number 123. 999. There should be a call setup between Phone-1 and Phone-3. Register a phone number is 9887872 for Phone-2. *73. Phone-1 should present ring back tone. Pick up Phone-2. the tone is depend on your settings. Dial tone should be presented. Pick up Phone-2. (page. Check the checkbox to enable or uncheck to disable. 4. *99… Example2. Dial tone should be presented. Set a rule on Phone-1 UI. Phone-2 should ring and Phone-1 should present ring back tone. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 44 Copyright © Huawei Technologies Co. 2.54) Dial Plan Example1. 9900. You can hear Call Waiting Tone from Phone-1. Phone-2 press the Flash button followed by the number of Phone-3.. and the tone is depend on your settings. 1. Ltd. Ring Back Tone 3. <xx. 1. Ring back tone should be stopped in Phone-1 and Call Waiting Tone bi-directional voice traffic should flow. Pick up Phone-2. 88888… 1. Pick up Phone-3. 5. Dial the number of Phone-2. and the tone is depend on your settings. Dial tone should be presented. Audio DTMF Method You can select different DTMF method here. 1. Dial the number of Phone-2 from the Phone-3. 7. 4. 5. Dial Tone 2. 2. 4. 4. Set a rule on Phone-1 UI. Dial tone should be presented. 5. Pick up Phone-1. 1. 6. Pick up Phone-2. Phone-2 present busy tone. 6. 4. Speed Dial 7. there are three options InBand / RFC2833/ SIPInfo Codec Setting Codec Enable: There are three codecs supported: g711u/g711a/g729. Phone-3 should start ringing and pick up Phone-3. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 45 Copyright © Huawei Technologies Co. for the g729.Priority: You can also set the priority of the codec Ptime: It defines the length of time in milliseconds represented by the media in a packet.. The ptime value tells the length of the speech block in the RTP packets. there are three options: 10/20/30ms. For the g711 u/a codecs. .there are four options: 5/10/20/30ms. Ltd. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 46 Copyright © Huawei Technologies Co.. . Ltd. 1. Traceroute Issue 01 (2015-07-10) Huawei Proprietary and Confidential 47 Copyright © Huawei Technologies Co. Example www.7 Management>Diagnostics This Diagnostics page will help you to perform a Ping or the Traceroute to troubleshoot the network connection. Choose Management > Diagnostics.4. Ltd. Sending Count: Please fill how many times the test need to be performed. 4. 2. The Ping page is displayed. To do so: 1. for example. Sending Buffer: Please fill how many buffer you want to add in a range of 4~1472byte. On the Diagnosis Tools. Enter the domain name in the IP Address field. Wait until the ping command is executed. run the ping command to preliminarily identify the problem. − Diagnostics Ping Test IP address: To issue a Test. set to Ping. please enter the destination IP address and Domain name here.. 6. 3.com. The execution results are displayed in the box. If the CPE fails to access the Internet. Set Sending Count and Sending Buffer. Click Run 5.google. . 2. The execution results are displayed in the box. for example. TTL: Time To Live value.google. Example www. On the Diagnosis Tools. please enter the destination IP address and Domain name here. IP address: To issue a Test. run the traceroute command to preliminarily identify the problem. Click Run 5. in the Traceroute test.com. please fill in a test value for the packet path time and check what is the path time that a packet takes to the specified host. 3. Wait until the traceroute command is executed. Ping page Issue 01 (2015-07-10) Huawei Proprietary and Confidential 48 Copyright © Huawei Technologies Co. Enter the domain name in the IP Address field. set to Traceroute. If the CPE fails to access the Internet. .. To do so: 1. Choose Management > Diagnostics. Set TTL 4. The Traceroute page is displayed. 6. Ltd. Verify PIN failed . Started/Stopped . Please see below table. Call session establish established phone call Issue 01 (2015-07-10) Huawei Proprietary and Confidential 49 Copyright © Huawei Technologies Co. WAN Connection . Register to SIP server register to SIP VoIP . SIM card is Connection .8 Management> System Log The system log allows you can provide more detail information to your network provider. System Log Information Warning Error Critical System . Failed to . Ltd.1. WAN IP obtained not inserted Manager . Log level There are four levels pre-defined: Critical/Error/Warning/Information. . Call Out/In . Start/Reboot/Reset .. Trace route page 4. Failed to . System log will not be recorded any individual privacy. Failed to . Block/Un-block Operation DHCP client . Firmware upgrade to session fail timeout . User cancels the user upgrade notification . DHCP server IP is changed . Periodic Firmware connect to upgrade check/upgrade result server firmware FOTA . FW upgrade from UI . Firewall level is changed . Start/Stop Ping . Web login password is changed . Failed to . Started/Stopped . Web login is failed login/logout by . Start/Stop WPS . Failed to send register message to SIP server . Web logout due . client: unauthorized associated/disassociated . Start upgrade firmware Packages or firmware firmware Operation Log Information Warning Error Critical . Modify each page . WiFi SSID is changed . Failed to firmware download verify . Starts download . Web . Start/Stop Traceroute .. . Failed to . WiFi security is changed . . Ltd. Export/Import Configuration File Issue 01 (2015-07-10) Huawei Proprietary and Confidential 50 Copyright © Huawei Technologies Co. client: Wi-Fi . AP: started/stopped . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 51 Copyright © Huawei Technologies Co. Export: You can export your syslog out for the further analysis or issue tracking.Scroll Auto: If you checked the Scroll Auto checkbox the syslog will always scroll to the bottom line to display the latest log If you just want to view the previously log..txt file with . the export format will be the .2 Personalization 4.1 Personalization>PIN Management − USIM status This column will show current SIM card's status. USIM Ready SIM card insert properly andbeendetected SIM card is protected by PIN or PUK code. please un-checked it. please go “U/SIM's PIN/PUK Wait PIN /PUK code Verification” verify the code. detail definition as below: USIM not inserted Your SIM card is not insert or SIM Card not able to be detected properly.tar compress. Ltd. . 4.2. PINcodeshould be 4-8 digits number. You can only use your SIM card after verify the PIN or PUK code. the column will becomeactivate. If PIN retries error over 3 times. After PUK codeis filled. device would disable the PIN code lock function. Other Reason Your SIM card can’t not use. ※If you are in the first time use. device will activate SIM PIN Code Lock function which will request you to fill-in the PINcodewhile every time device boot up. Please fill yourOld (Original) PIN code and New PIN code then confirm the New PIN code again. you can renew your PIN code here. please press “Apply” button to confirm the change. please check your SIM card/Network provider. − USIM's PIN/PUK Verification Only when your SIM card is locked by PIN/PUK code. press“Verify”to begin PUK verification. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 52 Copyright © Huawei Technologies Co. Please enter your PIN code (4~8digits number) then press “Apply” button to confirmed the PIN code lock. − USIM's PIN Management If you select “enabled’. . − USIM's Change PIN If the PIN Code Lock function isEnable.. Please fillyourPINcodehere then press “Verify” button. SIM card will be blocked and PUK code will be required to unblock the SIM card. please check Network Provider to get your PIN/PUK code details. Ltd. PUKcodeshould be 8 digits number. Normally. If you select “disable”. press ”Change” button to confirm the change. .Issue 01 (2015-07-10) Huawei Proprietary and Confidential 53 Copyright © Huawei Technologies Co. Ltd. . <. Export Configuration File You could export all of user settings in this device to a file. After applying factory defaults. Export/Import Configuration File Import/Export Password Before export the file or import a file you need to input the password here (Password must contain 2 cases of uppercase letter. lowercase letter.2. device will reboot.:'".2 Personalization>Configuration Restore Factory Settings You can use Reset Factory Settings function to set device to factory default settings. All the changes different from factory default settings will be lost.>/?). Ltd. 4. space. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 54 Copyright © Huawei Technologies Co. number. it will reset all the parameters/settings you had ever done.. and special characters(`~!@#$%^&*()-_=+\|[{}]. click the Restore Factory Settings button. Import Configuration File You could browse a configuration file and import it back. . you will need to manually change the parameter again. When returning to factory defaults. Restore Factory Settings To restore settings to factory defaults. Current Local Time Displays the current time of the system clock. Maintaining an accurate time on the device will keep the system log to recording meaningful dates and times for event entries. it means that you don’t modify password.3 Personalization>Device Setup − Password You can change the default Graphical User Interface (GUI) access password here. NOTE If you don’t fill any key in the Password field.2. 4. Primary NTP Server You can change the Primary NTP server if the default NTP server is not work. Ltd. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 55 Copyright © Huawei Technologies Co. Password Maximum Length: Please define the password maximum length here in a range of 6~128. the new password total digits can’t more than the value you set on the”Password Maximum Length”column Confirm New Login Password: Enter the new password again for verification. Secondary NTP Server You can set the secondary NTP server in case of the Primary NTP server didn’t work in some time.. Old Login Password: Input the original /current login password New Login Password: Enter a new log-in password you want to change. if any. − Device Time The modem uses the Simple Network Time Protocol (SNTP) to set its internal clock based on periodic updates from a time server. The Device Time area displays the following information: Enable NTP Allows user to connect what type of time server. . Time Zone SNTP uses Greenwich Mean Time.00. . The Device Name page displays the following information: Current Device Name Display current device name.). zero degrees longitude. You can type the device name. To display a time corresponding to your local time.) Auto Adjust for Daylight Saving Time Select this check-box to set the daylight saving time if the unit operates in a region that observes daylight saving time. Click Apply to activate your changes Issue 01 (2015-07-10) Huawei Proprietary and Confidential 56 Copyright © Huawei Technologies Co. for Central Time (US and Canada.. New Device Name Enter a new name for your device (limits up to 20 ASCII printable characters) and click Apply. Click Undo to clear the changes that you have made to this window. or UTC) based on the time at the Earth's prime meridian. followed by a dot symbol (. The default is UTC-06. select your time zone from the pull-down list. Ltd. or GMT (also known as Universal Time Coordinated. − Device Name This area allows you to define a name that identifies your device. Using an easy-to-remember name instead of the default one.) in the address bar of the Web browser to login from LAN (For example: http://huaweilte. this can simplify the access to the device's GUI Setup menu. .Issue 01 (2015-07-10) Huawei Proprietary and Confidential 57 Copyright © Huawei Technologies Co.. Ltd. 4. you can do update or not. if your device SW is not up to date. please keep your device powering on. Don’t turn off the device to prevent the possible damage. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 58 Copyright © Huawei Technologies Co. − Upgrade From FOTA: (Remote management server): Please manually press “Check Version” button and device will request the latest update from the remote access server. .server will return message: Can't connect to Server/Latest Version. in each release you will get the ipk file release mtn_V100R001C01SPCxxx_arm.. NOTE While FW is upgrading.2. Ltd.ipkg. After checked.4 Personalization>Software − Upgrade From file: Step 1: ClickBrowserbutton to select the IPK file.ipk) Step 2: Click Install Software button to install the selected IPK file. (The IPK is the file with . . Ltd.Issue 01 (2015-07-10) Huawei Proprietary and Confidential 59 Copyright © Huawei Technologies Co. . Firewall Level Allows user to change the device firewall level here.. you can go Advanced>MAC Filter to edit backlist or whitelist Block or allow the client device’s internet access via IP IP Filtering address. Block or allow the client device’s internet access via MAC Filtering MAC address. you can customize the MAC Filtering. .4. there are four options pre-defined: Low (filtering disabled) Firewall Level Medium (standard) High Custom (If you chose Custom option. IP Filtering and URL Filtering options) Filtering The filtering rules you set will take over the default Strategy inbound and outbound policies. It also allows the device to be managed over the Internet by authorized user.1 Basic>Firewall The modem provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. you can go Advanced>IPFilter to edit backlist or whitelist Block or allow the client device’s internet access via URL Filtering URL(web address).3. Ltd. you can go Advanced>URL Filter to edit backlist or whitelist Issue 01 (2015-07-10) Huawei Proprietary and Confidential 60 Copyright © Huawei Technologies Co. The firewall feature can be used to block unauthorized access and allowing only authorized communications from the Internet network.3 Basic 4. This page is to configure and change the firewall settings. Current Shows the current device firewall level. If this feature is enabled. DoS Attack Block Denials of Service (DoS) attacks from the LAN and Internet. Filter IDENT (Port 113) Select this check-box to drop incoming packets from the unit WAN side with destination port 113. Ltd. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 61 Copyright © Huawei Technologies Co. . Filter Multicast Select this check-box to filter out multicast packets. such as SYN floods and ping floods. Click Apply to activate your changes. Click Undo to clear the changes that you have made to this window.. Filter Internet NAT Redirection NAT Redirection is used to block access to the local server from the local PC via unit's WAN IP. . Block Anonymous Internet Requests Select this check-box to reject anonymous Internet requests. local PC can only access the local server via unit's LAN IP. . 4. Ltd. DMZ IP Address Set a server that acts as a "neutral zone" (DMZ stands for "Demilitarized Zone") and separates an internal network from a public one in order to prevent outside access to private data..2 Basic>DMZ For applications that require unrestricted access to the Internet. . Click Apply to activate your changes. you can configure a specific client/server as a demilitarized zone (DMZ). .3. Enable DMZ Select this check-box to enable or disable DMZ. . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 62 Copyright © Huawei Technologies Co. The DMZ forwards the network traffic to specific hosts based on the protocol and port number. Click Undo to clear the changes that you have made to this window. a protocol that simplifies device connection and network implementation. 4. Click Undo to clear the changes that you have made to this window..3 Basic>UPnP UPnP Enable UPnP IGD . When this option is enabled. .Select this check-box to enable/disable Universal Plug and Play Internet Gateway Device . . certain Windows applications would setup the port forwarding rule dynamically. Click Apply to activate your changes. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 63 Copyright © Huawei Technologies Co. Ltd. .3. ..3. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 64 Copyright © Huawei Technologies Co. . Click Apply to activate your changes.When DDNS is enabled. 4. Ltd. Click Undo to clear the changes that you have made to this window.4 Basic>Dynamic DNS Dynamic Domain Name System (DNS) is a mechanism used for translating host names for network nodes into IP addresses in real-time. . The Dynamic DNS page includes the following parameters: Enable DDNS Select this check-box if the unit has a non-static IP address to keep the domain name associated with an ever-changing IP address. configure the following parameters: Username Password Domain Name Host Name Service Provider Select the DDNS service provider from the drop-down list. This page allows enabling the Dynamic DNS and selecting the service provider. 3. Click Undo to clear the changes that you have made to this window. . Enable L2TP Passthrough Layer 2 Tunneling Protocol. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 65 Copyright © Huawei Technologies Co. . Enable PPTP Passthrough Point to Point Tunneling Protocol. an open standard with multivendor interoperability and acceptance. IPSec provides encrypted security services at the IP layer. and enables to use encrypted tunnels/traffic between two hosts. Ltd. . This protocol enables the transfer of data packets of TCP / IP through a foreign network that is not based on these protocols (by marking the packet with an address suited to the foreign network). 4..5 Basic>VPN Passthrough Enable IPSecPassthrough Internet Protocol Security. Click Apply to activate your changes. . Ltd..Issue 01 (2015-07-10) Huawei Proprietary and Confidential 66 Copyright © Huawei Technologies Co. . Select Selecting this check-box and press Del button to delete this row. you can set filtering by blacklist or whitelist on MAC filtering mode. Ltd. MAC address: Please key-in the client device which you want to do the MAC filtering MAC address. You can add addresses to the filtered group or delete them.. Whitelist: Will ONLY allow the units listed on the list to access the network. In the MAC Filter page you set MAC addresses to be filtered out by the security system.1 Advanced>MAC Filtering You can block access to the Internet from clients on the local network by MAC addresses.4. High: Filtering enable.4. you need to go to the Basic>Firewall level to change the firewall setting.4 Advanced 4. The following configuration parameters are available: Current MAC filtering status Shows the MAC filtering function is disable or enable. and also enable or disable filtering at different times. Custom: You can customize if you want to Disable or set Blacklist/Whitelist MAC filtering mode Select MAC filtering by Whitelist or Blacklist Blacklist: Block internet access which listed on the blacklist. you can set filtering by blacklist or whitelist on MAC filtering mode. Enabled Select this check-box to enable/disable filter for the specific client device’s MAC address Issue 01 (2015-07-10) Huawei Proprietary and Confidential 67 Copyright © Huawei Technologies Co. Low: Filtering disable Medium: Filtering enable. To enable or disable. You can configure up to five IP filters on the unit. To enable or disable. you can set filtering by blacklist or whitelist on IP filtering mode.4. Ltd. . Select Issue 01 (2015-07-10) Huawei Proprietary and Confidential 68 Copyright © Huawei Technologies Co. Low: Filtering disable Medium: Filtering enable. you need to go to the Basic>Firewall level to change the firewall setting. Whitelist: Will ONLY allow the unit listed on the Whitelist to access the network. The following configuration parameters are available: Current IP filtering status Shows the IP filtering function is disable or enable. High: Filtering enable.2 Advanced>IP Filtering You can block access to the Internet from clients on the local network by specifying IP addresses and TCP/UDP port numbers. 4. you can set filtering by blacklist or whitelist on IP filtering mode. You can also enable or disable filtering at different times. In the IP Filter page you set IP addresses to be filtered out by the security system. You can add addresses to the filtered group or delete them.. Custom: You can customize if you want to Disable or set Blacklist/Whitelist IP filtering mode Select IP filtering by Whitelist or Blacklist Blacklist: Block internet access which listed on the Blacklist. Click Apply to activate your changes. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 69 Copyright © Huawei Technologies Co. IP Range Specify an IP address or range on the local network. . Ltd.Selecting this check-box and press Del button to delete this row.Click Undo to clear the changes that you have made to this window. please click Apply button to confirm the Add or Del.Use the Add or Del buttons to add the rule to the group or clear it from the group. Protocol Set the protocol to be filtered: TCP or UDP. . Port Range Enter the port range to be filtered. .. . Enabled Select this check-box to enable or disable filtering for the specific table entry. please click Apply button to confirm the Add or Del..3 Advanced>Port Forwarding Port Forwarding instructs the router to which computer on the local area network to send data. UDP or Both. The following configuration parameters are available: Select Select this check-box and press Del button to delete this row.Use the Add or Del buttons to add the rule to the group or clear it from the group. LAN IP Enter the IP address that identifies the IP subnet of the remote network. Ltd. Protocol Set the protocol for port forwarding: TCP. .Click Apply to activate your changes.Click Undo to clear the changes that you have made to this window. 4. The Port Forwarding page enables managing and setup of the rules for Port Forwarding. LAN Port Enter theport number for LAN side. .4. . According to the port forwarding rules or setup. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 70 Copyright © Huawei Technologies Co. WAN Port Enter the port number for WAN side. Port Forwarding rules are created per port. Enabled Select this check-box to enable/disable port forwarding for the specific IP. the router sends the data from the external IP address: port number to an internal IP address: port number. . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 71 Copyright © Huawei Technologies Co. Port triggering can open an incoming port when a client on the local network makes an outgoing connection on a predetermined port or range of ports. No. 4. UDP or BOTH. Display the number of the port trigger rule. In the Port Trigger page you can specify up to 15 rules with parameters for Port Triggering..4 Advanced>Port Trigger Port triggering is a way to automate port forwarding: outbound traffic on predefined ports ('triggering ports') causes inbound traffic to specific incoming ports to be dynamically forwarded to the initiating host. Protocol Set the protocol for port trigger: TCP. while the outbound ports are in use. Forwarded Range Enter the forwarded range (1~65535). Enabled Select this check-box to enable/disable port trigger for the specific application. Application Name Enter a name for identifying this port trigger protocol. The following configuration parameters are available: Select Select this check-box and press Del button to delete this row. This allows computers behind a NAT-enabled router on a local network to provide services that would normally require the computer to have a fixed address on the local network. . Triggered Range Enter the trigger range (1~65535).4. Ltd. please click Apply button to confirm the Add or Del. .Click Undo to clear the changes that you have made to this window. . . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 72 Copyright © Huawei Technologies Co. Ltd..Use the Add or Del buttons to add the rule to the group or clear it from the group. .Click Apply to activate your changes. Blocked Content Enter the keywords that need to be filtered on layer 7. 4.. . .Click Apply to activate your changes.5 Advanced>Layer 7 Select Select this check-box and press Del button to delete this row. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 73 Copyright © Huawei Technologies Co. Ltd.4.Use the Add or Del buttons to add the rule to the group or clear it from the group.Click Undo to clear the changes that you have made to this window. it matters to the filtering result) . please click Apply button to confirm the Add or Del. (Please double check your Capital and Lower case letters. No. Display the number of the layer 7 rule. . . Issue 01 (2015-07-10) Huawei Proprietary and Confidential 74 Copyright © Huawei Technologies Co.Click Apply to activate your changes. Whitelist: Will ONLY allow the unit listed on the Whitelist to access the network. URL Enter the URL or URL’s keywords that needs to be filtered.4. .6 Advanced>URL Filtering Current URL filtering status Shows the URL filtering function is disable or enable. you need to go to the Basic>Firewall level to change the firewall setting.Use the Add or Del buttons to add the rule to the group or clear it from the group. No. 4. you can set filtering by blacklist or whitelist on IP filtering mode. it matters to filtering) . To enable or disable. . Display the number of the URL filtering rule. (Please double check your Capital and Lower case letters. Custom: You can customize if you want to Disable or set Blacklist/Whitelist URL filtering mode Select URL filtering by Whitelist or Blacklist Blacklist: Block internet access which listed on the Blacklist. please click Apply button to confirm the Add or Del. Ltd. you can set filtering by blacklist or whitelist on IP filtering mode. . High: Filtering enable. Select Select this check-box and press Del button to delete this row.Click Undo to clear the changes that you have made to this window. Low: Filtering disable Medium: Filtering enable. it is free defining with 10 units’ characters. 4. Dst Port Issue 01 (2015-07-10) Huawei Proprietary and Confidential 75 Copyright © Huawei Technologies Co. Name Enter a name for identifying this ACL filter rule. Src Port Please fill in the source port number range. .7 Advanced>ACL Filtering Select Select this check-box and press Del button to delete this row.. Dst IP Please define the start and end destination IP address that the filter rule applies. Ltd. Direction Define which direction for the filter LAN to Device LAN to WAN WAN to LAN WAN to Device Src IP Please define the start and end source IP address that the filter rule applies.4. Use the Add or Del buttons to add the rule to the group or clear it from the group. DROP ACCEPT .Click Apply to activate your changes.Please fill in the destination port number range. please click Apply button to confirm the Add or Del. Protocol Please select which type of package for filtering.Click Undo to clear the changes that you have made to this window. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 76 Copyright © Huawei Technologies Co. . TCP UDP BOTH Policy Please define what action to do for the filtering. . .. Ltd. Ltd.Issue 01 (2015-07-10) Huawei Proprietary and Confidential 77 Copyright © Huawei Technologies Co. .. NOTE This feature is supported under Gateway. 4. If it is enabled. . Please indicate the interface for setting the route rule. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 78 Copyright © Huawei Technologies Co. Router andVPN modes. Gateway Interface The gateway may be a router or switch on the same network segment as the device's LAN/WAN/Tunnelinterface.4.Use the Add or Del buttons to add the rule to the group or clear it from the group. . No.8 Advanced>Static Routing Select Select this check-box and press Del button to delete this row. Subnet Mask Please fill-in the subnet mask of the destination IP network.Click Apply to activate your changes. . the Static Routing setting page can be configured. .. Display the number of the Static Routing rule. please click Apply button to confirm the Add or Del. Ltd.Click Undo to clear the changes that you have made to this window. Destination IP Address Please fill-in the destination IP address for the route. If you set VPN for WAN operation mode the “tunnel” option will show up for configuration. . Ltd.Issue 01 (2015-07-10) Huawei Proprietary and Confidential 79 Copyright © Huawei Technologies Co. . the required settings are displayed. There are security options available. Ltd. When you select the security type from the list. and the software support provided on wireless clients. The security mechanism employed depends on the level of security required.4GHz WiFi Enable 2. Encryption Data passing between the unit and clients must be protected from interception and eavesdropping. .5. please checked the checkbox to hide the SSID and unchecked it to broadcast the SSID. all clients will be able to immediately connect to the Wi-Fi network. 2. Network Name(SSID) The Service Set ID (SSID) that identifies the Wi-Fi network. The SSID is case sensitive and can consist of up to 32 alphanumeric characters. The following security options are available for the Wi-Fi network.4GHz Wi-Fi radio. / 0 1 2 3 4 5 6 7 8 9 : < = > @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ ] ^ _ ` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ~ Hide SSID This function is to allow you to hide the SSID to prevent the unexpected connection request.5 WiFi 4. the modem can implement one of several security mechanisms. ' ( ) * .4GHz WiFi Enables / disables the 2. Following characters is valid for Network Name (SSID).4. For a more secure network. -Open System -Shared Key -WPA2 PSK Issue 01 (2015-07-10) Huawei Proprietary and Confidential 80 Copyright © Huawei Technologies Co. The option "Open System" together with encryption disabled is equivalent to no security. the network and management resources available. .1 Wi-Fi>Basic Enable Wi-Fi Enables / disables the Wi-Fi radio.. Radio Channel The radio channel is used by the unit and its clients to communicate with each other. all clients will be able to immediately connect to the Wi-Fi network.. .5.11 b/g/n is supported. Ltd. This channel must be the same on the unit and all of its wireless clients. The option "Open System" together with encryption disabled is equivalent to no security.4GHz Wi-Fi radio. please checked the checkbox to hide the SSID and unchecked it to broadcast the SSID.2 Wi-Fi>Advanced 2. and the software support provided on wireless clients. the required settings are displayed. AP Isolation Issue 01 (2015-07-10) Huawei Proprietary and Confidential 81 Copyright © Huawei Technologies Co. Power Level The power level High/Middle/Low stands for WiFiTx power.4GHz WiFi Working mode It shows what Wi-Fi standard protocol is supported 802. the modem can implement one of several security mechanisms. For a more secure network. The available channel settings are limited by local regulations. you can adjust it base on your environment condition. There are security options available. Hide SSID This function is to allow you to hide the SSID to prevent the unexpected connection request. the network and management resources available. The SSID is case sensitive and can consist of up to 32 alphanumeric characters. Encryption Data passing between the unit and clients must be protected from interception and eavesdropping. -Open System -Shared Key -WPA2 PSK -WPA-WPA2-Mixed PSK 4. -WPA-WPA2-Mixed PSK 5GHz WiFi Enable 5GHz WiFi Enables / disables the 2. Following characters is valid for Network Name (SSID). The following security options are available for the Wi-Fi network. Network Name(SSID) The Service Set ID (SSID) that identifies the Wi-Fi network. When you select the security type from the list. The security mechanism employed depends on the level of security required. and specify the details. Step 2: For the Allow and Deny lists. click Insert to add a MAC address to the list. . or denied from accessing. Allow or Deny.When the AP isolation is set to ON: The Wi-Fi clients can’t ping each other ACL Settings In this section you can add MAC addresses of clients which are allowed to access the system. . Ltd. AP Isolation When the AP isolation is set to OFF: All the connected Wi-Fi clients can ping each other. This channel must be the same on the unit and all of its wireless clients. click Insert to add a MAC address to the list. Step 1: Select either of Disable. Click Apply to activate your changes.When the AP isolation is set to OFF: All the connected Wi-Fi clients can ping each other. Step 2: For the Allow and Deny lists. Step 1:Select either of Disable. Allow or Deny.11 a/n/ac is supported. and specify the details. or denied from accessing. you can adjust it base on your environment condition. . Click Undo to clear the changes that you have made to this window. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 82 Copyright © Huawei Technologies Co.. Power Level The power level High/Middle/Low stands for WiFiTx power. Radio Channel The radio channel is used by the unit and its clients to communicate with each other.When the AP isolation is set to ON: The Wi-Fi clients can’t ping each other ACL Settings In this section you can add MAC addresses of clients which are allowed to access the system. 5GHz WiFi Working mode It shows what Wi-Fi standard protocol is supported 802. The available channel settings are limited by local regulations. the WPS will start and trying to connecting with the available clients. − PIN code: Please insert the WPS client PIN code. Issue 01 (2015-07-10) Huawei Proprietary and Confidential 83 Copyright © Huawei Technologies Co. − Start Select PBC and press start button. Ltd. 4. the PIN code length should be 4 or 8. Users should be aware that during the two-minute setup period which follows the push of the button. − Start After input the PIN code then press the start. PIN In Wi-Fi Protected Setup networks. a unique PIN (Personal Identification Number) will be required for each device to join the network. WPS will start and trying to connecting with the available clients. unintended devices could join the network if they are in range.5.3 Wi-Fi>WPS PBC User may connect multiple devices to the network and enable data encryption by pushing a button.. . .Issue 01 (2015-07-10) Huawei Proprietary and Confidential 84 Copyright © Huawei Technologies Co. Ltd. .