LOKRINGPROCESS PAMPHLET TECHNOLOGY 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________________________________www.lokring.com CORPORATION LOKRINGTM Specifications FS-3000 for Series MAS-3000 Carbon Steel Fittings Scope of Specifications: Series MAS-3000 carbon steel pipe fittings manufactured by LOKRINGTM. Pressure temperature ratings of qualified fittings, and matched pipe sized (NPS) and schedules are detailed in Table 1 and 2 of this specification. Fitting configurations and dimensions are detailed in LOKRINGTM product catalogs. Installation tool envelope dimensions, and minimum fit-up dimensions are provided in LOKRINGTM Installation Procedure Lp-105. For installation procedures, and selection of installation tooling, see LP-105 Installation Procedure. Fittings are designed for carbon steel pipe to ASTM-A106B and ASTM-A53B. Fitting Material Specification: Fitting body and swaging rings are manufactured from hot rolled micro alloyed 15V24 carbon steel bar or Drawn Over Mandrel, stress relieved tubing. Bar stock material shall conform to ASTM A675 and the chemical and mechanical properties shall conform to LOKRINGTM material specification LMS 92-10. Tube stock material shall conform to ASTM A513 / DIN 2393 grade ST 52.3 and the chemical and mechanical properties shall conform to LOKRINGTM material specification LMS 97-20. LOKRING's Carbon Steel Repair Couplings are made of a stainless steel body with carbon steel drive rings, see LOKRING specification FS40 for material data. For shelf-life corrosion protection, machined fittings shall be subjected to a black-oxiding process, followed by a rust inhibiting dip. Contact LOKRINGTM for material or plating specifications. Table 1: Pressure-Temperature Ratings (Note 1, 3, 5) Ambient Maximum design pressures (psi) ASME B31.1 ASME B31.3 Fitting/Matching Pipe Assembly Matching Pipe Schedule MAS-3000-XXX-P04 MAS-3000-XXX-P06 MAS-3000-XXX-P08 MAS-3000-XXX-P12 MAS-3000-XXX-P16 MAS-3000-XXX-P20 MAS-3000-XXX-P24 MAS-3000-XXX-P32 MAS-3000-XXX-P48 NPS ¼ NPS ⅜ NPS ½ NPS ¾ NPS 1 NPS 1¼ NPS 1½ NPS 2 NPS 3 40 40 40 40 40 40 40 40 40 4890 4040 3890 3230 3030 2480 2200 1790 1700 6250 5390 5190 4300 4050 3310 2930 2390 2270 MAS-3000-XXX-P04 MAS-3000-XXX-P06 MAS-3000-XXX-P08 MAS-3000-XXX-P12 MAS-3000-XXX-P16 MAS-3000-XXX-P20 MAS-3000-XXX-P24 MAS-3000-XXX-P32 MAS-3000-XXX-P48 NPS ¼ NPS ⅜ NPS ½ NPS ¾ NPS 1 NPS 1¼ NPS 1½ NPS 2 NPS 3 80 80 80 80 80 80 80 80 80 6610 5600 5250 4400 4080 3350 3970 2420 2260 8810 7470 7000 5870 5440 4460 3960 3230 2470 MAS-3000-XXX-P08 MAS-3000-XXX-P12 MAS-3000-XXX-P16 NPS ½ NPS ¾ NPS 1 160 160 160 4810 4240 3650 6410 5650 4870 LOKRING Fitting (Note 2) Notes: 1. Pressure-temperature ratings in Table 1 assume no corrosion allowance and negligible bending moments on the fitting. Please consult the factory for more detailed design guidance. 2. Carbon Steel Repair Couplings have pressure ratings the same as those of LOKRING's stainless steel pipe fittings see specification FS40 for details. Table 2: Temperature Derating Factors (Note 1, 5) www.lokring.com Temperature (ºF) Derating Factor for ASME B31.3 400 500 600 650 1.00 0.945 0.865 0.751 Copyright 2003 Lokring Technology Corporation, All rights reserved 1 4.04 FS-3000 (10-17-03) TECHNOLOGY 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________________________________www.lokring.com CORPORATION Matching Pipe for Qualified Fittings: Carbon Steel to ASTM-A106B and ASTM-A53B (Note 3) Stress Intensification Factor I: 1.2. (Note 4, 5) Reference Qualification Document: Biersteker, Dietmann, Sareshwala, and Haupt, “Qualification of NonStandard Product Form for ASME Code for pressing piping, B31 Applications” Codes and Standards and Applications for Design and Analysis of Pressure Vessel and Piping Components, PVP-Vol. 210-1, American Society of Mechanical Engineers, New York, 1991. Note 1: Piping systems containing the piping assemblies listed may establish design pressures up to and including the ambient maximum design pressure given for temperature from -20° to 400° F for ASME B31.3 (based on allowable stresses for the matching pipe of 15,000 psi and 20,000 psi respectively). For temperatures above 400°F in ASME B31.1 the maximum design pressure given shall be multiplied by the temperature derating factor listed in Table 2. Interpolation between derating factors is permitted. For methodology used to develop maximum design pressures in accordance with ASME codes, see Reference Qualification Document. Testing performed has disclosed that the toughness for the l5V24 material at -20°F to be comparable or better than matching pipe material (document available upon request). However, the toughness of matching pipe material may be affected when operating below normal ambient temperatures. Note 2: XXX designates fitting configuration: CPL = Coupling; TEE = Straight Leg Tee; EL90 = 90° Elbow. See product catalogs for available configurations. Note 3: Pipe used for pressure qualification tested was a seamless construction to ASME-SA106 Grade B, and electric resistance welded (ERW) construction to ASME-SA53 Grade B. Maximum pipe hardness Rb 90. For assemblies using ASTM A106 Grade A, A53 Grade A, or A587 matching pipe, the listed pressure-temperature ratings shall be multiplied by 0.80. Prior to using Series MAS-3000 fittings on other carbon steel pipe specifications, schedules, or constructions, consult with LOKRINGTM. When installing on ERW pipe, the longitudinal weld seam shall be drawn smooth or sanded to remove any suckback, flat spots, or other surface irregularities. If the required surface conditions cannot be met, the use of anaerobic sealant, such as Loctite® PST sealant (given process compatibility) is recommended. Note 4: The stress intensification factor, I, used for B31.1 thermal expansion and B31.3 displacement stress-range calculations has been established in accordance with test procedures outlined in the Reference Qualification Document. In this testing, an assembly consisting of a LOKRINGTM coupling two equal length pipe tangents on either side of the coupling was fabricated using standard LOKRINGTM installation procedures. A uniform bending moment was applied to the fitting/pipe assembly. This moment induced a bending stress in the assembly greater than the pipe material yield strength (35,000 psi), and caused the assembly to flex in plane passing through the neutral axis. In one complete flexural cycle, the fitting/pipe assembly bends an equal distance to either side of the neutral axis. The stress intensification thus determined means that the LOKRINGTM fitting/matching pipe assembly will normally survive 7,000 fully reversed flexural cycles with the matching pipe nominal stress equal to the pipe material yield strength. While extensive fatigue testing of the l5V24 fitting and matching pipe assemblies have been performed (documentation available upon request), it is cautioned that the l5V24 material is among the highest tensile strength materials approved for use in pressure component applications. In developing stress intensification data, one assembly endured 80,000 cycles at a nominal moment stress of 35,000 psi without failure. However, both B31.l and B31.3 provide notes suggesting caution when designing with materials other than those in the ASME data base. Thus, until more data is available, it is recommended that the B3l.l thermal expansion and B3l.3 displacement allowable stress-ranges be conservatively based upon grade B carbon steel allowable stress values. Note 5: The pressure-temperature ratings and the stress intensification factor given are for the LOKRINGTM coupling fitting/matching pipe joint only. If the LOKRINGTM fitting is the TEE or EL90, a forged tee or elbow exists between LOKRINGTM couplings located at the ends of the product form. Calculations and testing confirm that effective pressure-temperature ratings and the effective stress intensification factors (based on matching pipe cross-sectional properties) are enveloped by LOKRINGTM coupling/matching pipe values. This is true as well for conditions where corrosion has internally reduced the wall thickness such that pressure-temperature rating and stress intensification factor could be affected. For flexibility calculations, the tee or elbow may conservatively be considered as a rigid member. www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 2 4.04 FS-3000 (10-17-03) TECHNOLOGY 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________________________________www.lokring.com CORPORATION LOKRINGTM Specifications FS40 for Series SS40 316L Stainless Steel Fittings Scope of Specification: Series SS40 Type 316L stainless steel pipe fittings manufactured by LOKRINGTM. Pressure-temperature ratings of qualified fittings, and matching pipe sizes (NPS) and schedules detailed in Tables 1 and 2 of this specification. Fitting configurations and dimensions are detailed in LOKRINGTM product catalogs. Installation tool envelope dimensions, and minimum fit-up dimensions are provided in LOKRINGTM Installation Procedure Lp-105. For installation procedures, and selection of installation tooling, see Installation Procedure LP-105. Fittings are designed for stainless steel pipe to ASTM-A312, and for other pipe materials of comparable strength and ductility (Note 2). Material of Construction: Fitting bodies and swage rings are manufactured for corrosion resistant steel type 316L (UNS designation S31603). Physical and mechanical properties of bar stock material conform to ASTM A276 or A479, and to LOKRINGTM material specifications LMS 90-03 or LMS 95-15. Physical and mechanical properties of tube stock material conform to ASTM A511, and to LOKRINGTM material specification LMS 92-11, LMS 96-18 or LMS 99-23. Fittings are fabricated using Schedule 40 butt weld fittings to ANSI B16.9 and ASTM A403 WP/W. LOKRINGTM flanges are fabricated using forged weld neck flanges to ANSI/ASME B 16.5 Sch 40 bore. Table 1: Pressure-Temperature Ratings (Note 1) Ambient Maximum design pressures (psi) ASME B31.3 ASME B31.1 NPS Pipe Sch SS40-XXX-P04 ¼” 10S 40S 80S 4529 6300 8000 3781 5300 6000 SS40-XXX-P08 ½” 10S 40S 80S 4290 5060 5060 4030 4760 4760 SS40-XXX-P12 ¾” 10S 40S 80S 3380 4470 5250 3170 4210 4930 SS40-XXX-P16 1” 10S 40S 80S 3550 3920 4240 3340 3680 3990 SS40-XXX-P24 1½” 10S 40S 80S 2410 2600 2600 2260 2440 2440 SS40-XXX-P32 2” 10S 40S 1840 1840 1730 1730 SS40-XXX-P48 3” 10S 40S 80S 1150 2100 1705 920 1700 1350 LOKRING Fitting Note: Ambient maximum design pressures shown assume no corrosion allowance and negligible bending moments. Please consult the factory for more details. Qualified Matching Pipe: See Note 2 Stress Intensification Factor I: 1.2 (Note 4) Qualification Document: Biersteker, Dietemann, Sareshwala, and Haupt, “Qualification of Non-Standard Product Form of ASME Code for pressure piping, B31 Applications”, Codes and Standards and Applications for Design and Analysis of Pressure Vessel and Piping Components, PVP-Vol. 210-1, American Society of Mechanical Engineers, New York, 1991. www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 1 4.05 FS40 (10-01-03) 00 1. fully annealed construction with maximum Rockwell B scale hardness of 90.000 psi respectively). Fittings may also be installed on carbon steel pipe to ASTM A53 or A106 provided the dimensional and physical properties meet the requirements of qualified stainless steel pipe.84 0.80 Note 1: Piping systems containing the piping assembles listed may establish design pressures up to and including the ambient maximum design pressure given for temperatures from -20 to 100 degrees F for ASME B31. The stress intensification thus determined means that the LOKRINGTM fitting/matching assembly will normally survive 7. For temperature derating factor listed in Table 2.97 0.3 (based on allowable stresses for the matching pipe of 18.90 0.lokring. such as Loctite® PST sealant (given process compatibility).89 0.3 1.1 ASME B31.05 FS40 (10-01-03) .000 fully reversing flexural cycles with the matching pipe nominal stress equal to the pipe material yield strength.com CORPORATION Table 2: Temperature Derating Factors (Note 1) Temperature (ºF) 200 300 400 500 600 650 700 750 800 Temperature derating factors In accordance with ASME B31.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________________________________www. EL90 = 90°Elbow.000 psi and 20.1 thermal expansion and B31. Poor longitudinal welding can result in a visible depression (or suck back): poor longitudinal fittings on ERW pipe in which the weld bead has been drawn or sanded smooth.00 0. and is not visible to the naked eye.81 0. SS40 series fittings should not be installed on galvanized pipe used for flammable or process services. use of B31. Note 3: XXX designates fitting configuration: CPL = Coupling. and should limit the maximum rated temperature of the carbon steel pipe.90 0. Note 2: Qualified matching pipe shall conform to seamless or electric resistance welded (ERW) constructions of ASTM-A312.82 0.87 0.85 1. All rights reserved 2 4.com Copyright 2003 Lokring Technology Corporation.00 0. The designer should evaluate the potential for galvanic corrosion between the carbon steel pipe and stainless steel fitting for the contemplated application.86 0. www. available on request.96 0. TECHNOLOGY 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL. is suggested. available on request.3 displacement stress-range calculations is outlined in the Reference Qualification Document.85 0.1. For methodology used to develop maximum design pressures in accordance with ASME codes. TEE = Straight Leg Tee. Note 4: The methodology used to establish the stress intensification factor. I. see Reference Qualification Document. Pipe shall be of high quality. and from -325 to 100 degrees F for ASME B31. Interpolation between derating factors is permitted. Discontinuities as the longitudinal weld seam of ERW pipe can provide a leak path if not removed or sealed.96 0. See product catalogs for available configurations. If the required surface conditions cannot be met. All pipe shall be furnished in the heat-treated condition as per ASTM A312/A312M.lokring.98 0. the use of anaerobic sealant. semi-automatic and manual TIG welding machines.083" 0.3 4 9050 5650 4270 3750 3510 3420 3380 3550 3410 1690 ® Registered Trademark of Lokring Technology Corporation ™Trademark of Lokring Technology Corporation www. Table 1 Pressure Rating Coupling .06 FS40-T (08-19-03) . for appropriate installation procedures and installation tooling. T04 T06 T08 T10 T12 T14 T16 T20 T24 T32 2 Wall Thickness 1/4 3/8 1/2 5/8 3/4 7/8 1 1 1/4 1 1/2 2 Ambient Max.com Copyright 2003 Lokring Technology Corporation. Physical and mechanical properties of bar stock material conform to ASTM A276 or A479 and to the appropriate Lokring material specification. Fittings were designed and tested to join stainless steel tubing to ASTM A269 or A213 or equivalent (note 2).lokring.Matching Tube Assembly Fitting Size Tube O. All rights reserved 1 4. Material Specification: Fitting bodies swage rings and shapes are manufactured from corrosion resistant steel. tees.065" 0. (PSI) 3 0. Pressure – Temperature ratings of qualified couplings and matching tube sizes and wall thickness are detailed in table 1.lokring. Sizes and dimensions are detailed in Lokring product catalogs.9 or Flange to ASME/ANSI B16.065" 0. Ratings are based on proper installation of fittings. type 316L (UNS designation S31603).065" 0. TECHNOLOGY 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL. All personnel performing welds are certified to the local governing body in accordance to ASME Section IX. The weld end preparation on all components has been specifically designed to produce consistent high quality welds using automatic.5 or to a specially designed component machined from the same material type as the half bodies.083" Qualified Matching Tube: Stainless Steel tube to ASTM A269 or A213 2 Flexural Fatigue Testing: See note 5 B31. Lokring elbows.120" 0. All welding is performed in accordance with Welding Procedure Specifications and Welding Procedure Qualification Records that have been qualified to ASME Section IX.065" 0.065" 0.065" 0. flanges and other shapes that cannot conveniently be manufactured from a single component are fabricated by butt welding one or more machined Lokring “half bodies” onto a butt weld fitting procured to ASME/ANSI B16.: (905) 639-4050 FAX: (905) 639-6163 www. Design 1 Press.109" 0. D.com _______________________________________________________________________________________________ CORPORATION Specification FS40-T for Lokring Type 316L Stainless Steel Tube Fittings Scope: FS40-T covers Tube fittings manufactured by Lokring TM from 316L corrosion resistant steel. consult factory. and many greatly exceeded this value.00 1.000 complete bending cycles without leakage. In fatigue testing.3 (based on the use of seamless tube with allowable stresses of 20. 200 300 400 500 600 650 700 750 800 Notes: 1. New York. ® Registered Trademark of Lokring Technology Corporation ™Trademark of Lokring Technology Corporation www. the use of an anaerobic sealant such as Loctite PST (given process compatibility) will usually ensure a sound connection. and conform to seamless or electric resistance welded (ERW) construction of ASTM A269 and/or A 213.lokring. Tubing systems containing the tubing systems listed may establish design pressures up to and including the ambient maximum design pressure given for temperatures from –325 to 100 Deg.90 0. 1991 Table 2 Temperature De-rating Factors Temperature de-rating factors in accordance with ASME B31.035” up to ¾ O.lokring. Dietemann. A uniform bending moment was applied to the assembly. F for ASME B31.82 0.: (905) 639-4050 FAX: (905) 639-6163 www. assemblies consisting of a Lokring coupling and two equal length tube tangents on either side of the coupling were fabricated using standard Lokring installation procedures. Interpolating between de-rating factors is permitted. F. 0. Poor welding can result in a visible depression (or “suck-back”). poor weld bead removal can result in a raised portion or a flat spot at the weld. but pressure rating will remain at specified value. Pressure rating is maximum rating for the fitting size shown.97 0.000 PSI).com Copyright 2003 Lokring Technology Corporation. Discontinuities at the longitudinal weld seam of ERW tube can provide a leak path if not removed.84 0.com _______________________________________________________________________________________________ CORPORATION Biersteker. Consult factory for other details. For temperatures above 100 Deg.065” for sizes above ¾”) and pressure rating will be dependant on tube pressure limitations. TECHNOLOGY Reference Document: 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL. Only install Lokring fittings on ERW tube in which the weld bead has been drawn or sanded smooth and is not visible to the naked eye.000 PSI). 5. All rights reserved 2 4.D.85 0. the maximum design pressure given shall be multiplied by the temperature Derating factor listed in table 2. Sareshwala and Haupt. Ambient temperature system design pressure ratings must be de-rated when using ERW (welded) and/or “L” grade tubing with lower allowable stress.81 0. inducing a bending stress in the assembly equal to or greater than the tube minimum yield strength (38.. All assemblies exceeded 30. 2. B31 Applications” Codes and Standards and Applications for Design and Analysis of Pressure Vessel and Piping Components. 4. Qualified matching tube shall be Types 316/316L or 304/304L. Heavier wall tubing may be used. Conversely thinner wall tube may be used (minimum 0.80 Temperature Degree F. One complete bending cycle consists of bending the assembly to one side of the neutral axis to the specified value and then back again through the neutral axis to the specified value on the opposite side and then back to the neutral axis. “Qualification of Non-Standard product Form for ASME Code for Pressure Piping. PVP-Vol 210-1.06 FS40-T (08-19-03) .3 1. If the required surface conditions cannot be met.00 0.. 3. American Society of Mechanical Engineers. Reducer Bushings.com General Information …………… Page 1 Couplings. Adapters …………… Page 2 Adapters. Tees …………… Page 10 Copyright 2003 Lokring Technology Corporation.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04) . Uthreads …………… Page 4 Flanges …………… Page 5 Repair Couplings. T E C H N O L O G Y C O R P OR A T I O N MAS-3000 PIPE FITTINGS www. All Rights Reserved. 6. SAE Fittings …………… Page 6 45º Elbows. Caps.lokring. Reducers. 90º Elbows …………… Page 8 90º Elbows. 95 3" (P48) 40/80 4.08 2. 6.12 1.08 1/2" (P08) 40/80/160 1.86 1 1/4" (P20) 40/80 2.33 1 1/2" (P24) 40/80 2.87 2. Autocad-DXF and Intergraph PDS are available for most configurations.98 1.37 0.56 1. E 1/4" (P04) 40/80/160 1.43 1. All dimensions are reference only and subject to change www.60 1.52 1" (P16) 40/80/160 1.69 2. B Outside Diameter.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).72 2.05 0. All Rights Reserved. Fitting material Micro Alloyed Carbon Steel to LMS 92-10 or LMS 97-20 6.62 1. A Insertion Depth PostInstall. C. D & E are applicable to other fittings of the same size within this catalog 3.85 1. Zinc plate is available as an alternate 7.21 1. B. contact Lokring™ for details 9.24 3/4" (P12) 40/80/160 1.lokring.33 2.93 3. For tooling dimensions refer to appropriate catalog 5.53 6. D Minimum Straight Run Before a Bend.26 2.57 2.68 3.24 0.com Copyright 2003 Lokring Technology Corporation. Page 1 of 11 .34 3.16 3.41 1.29 1.26 2. Dimensions A.01 1.59 1.92 2. Standard coating is black oxide per LMS 93-12.99 4.46 0. All dimensions in inches 2.24 0.16 1. C Inside Diameter.39 1. contact Lokring for details 8. CAD files in Autocad-DWG.95 1. Other part configurations than those shown and custom configurations may be available.41 3.64 2" (P32) 40/80 2. General Information T E C H N O L OG Y C O R P OR A T I ON PRE-INSTALLED POSITION POST-INSTALLED POSITION Fitting Size (PXX) Qualified Pipe Schedules Insertion Depth PreInstall.95 1. For use on carbon steel pipe as per ASTM A53 AND A106 4.89 3/8" (P06) 40/80/160 1. 50 P32-P12 9060523 2.00 P24-P16 9060500 1.2 .75 9062019 1.25 P32-P16 9060502 2.5 P24 .37 P48-P32 9061774 5. A M12 9062378 0.com Copyright 2003 Lokring Technology Corporation. Page 2 of 11 . A Thread P08 .50 P20-P12 9061454 1.73 P24-P08 9060519 2.81 1 1/2 . T E C H N O L O G Y C O R P OR A T I ON Couplings.12 P24-P12 9060521 2.50 9061822 1.14 P12 . All Rights Reserved.11.66 P32 9040067 0.11.lokring.41 P20-P16 9061291 1.00 9061823 1.60 P20 9040110 0.25 P16-P08 9060496 1.59 P24 9040068 0.85 Fitting Size MXX Piece Number Take Out.14 P16 . 6.98 1/2 .25 9061821 1.97 3/4 .27 Fitting Size PXX-PYY Piece Number Take Out.0. Reducers.75 1 1/4 .1.47 P12 9040070 0.23 P32-P24 9060504 2.40 P06 9041375 0.11. A P04 9041374 0.5 P32 .01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).20 P48-P16 9061831 5. A P08-P04 9062518 1.38 1 .11.45 P08 9040071 0.5 MAS-3000-CPL-MXX (METRIC PIPE COUPLING) MAS-3000-RED-PXX-PYY MAS-3000-ADPT-PXX-YY FPT *Threaded end conforms to female NPT thread www.00 9062020 2.50 9062270 0.42 P48-P24 9061830 5.25 P32-P20 9062291 2.71 P48 9041804 0.50 P16-P12 9060498 1.1.47 P16 9040069 0.09 P08-P06 9062519 1.88 P32-P08 9060527 2.0.01 P48-P08 9061832 5.1.5 P20 .12 P12-P08 9060517 1.39 Fitting Size PXX-YY FPT Piece Number Take Out.89 2 . Adapters MAS-3000-CPL-PXX Fitting Size PXX Piece Number Take Out. 5 9061816 1.5 9061812 1.18 0.33 1 1/16-12 UN-2A P16-37F16 9062328 2.1.47 1/4 .51 2 .3/4" 9060580 1.5 1.14 1.63 1 7/8-12 UN P32 .11.1/4" 9062295 1.50 *Threaded end conforms to male NPT thread MAS-3000-ADPT-PXX-XX SAE Fitting Size PXX-XX SAE Piece Number Take Out.58 2 1/2-12 UN-2A Thread * Threaded end conforms to SAE J514 (37º FLARE) www.60 1/4-18 *Threaded end conforms to female NPT thread MAS-3000-ADPT-PXX-XX MPT Fitting Size PXX-XX MPT Piece Number Take Out.68 1 5/16-12 UN * Threaded end conforms to SAE J1926/2 (O-ring straight thread adapter) MAS-3000-ADPT-PXX-37FYY Fitting Size PXX-37FYY Piece Number Take Out. Page 3 of 11 .50 P48 .0.1.5 2.0 9062022 2.0 9061814 1.11.36 1 .45 1 1/2 .11. A Thread P12-1/4" 9061734 0.lokring.44 3/4 -16 UNF P12 .0.com Copyright 2003 Lokring Technology Corporation. A P08-37F08 9062326 1.2" 9060586 2.1 1/2" 9060584 2.13 P32 .38 P16 .1. 6.75 9061813 1.69 P24 .88 P08 .5 9062154 1.38 1 1/16-12 UN P16 .5 2. Adapters T E C H N O L O G Y C O R P OR A T I O N MAS-3000-ADPT-PXX-YY FPT Fitting Size PXX-YY FPT Piece Number Take Out. A Thread Across Flats P04 .13 P12 .3" 9061630 3.29 3-8 3.1.92 1 1/16-12 UN P16 .50 1 5/16-12 UN P20 .72 1 5/8-12 UN-2A P24-37F24 9062329 3.1/2" 9060578 1.11.0.32 1 7/8-12 UN-2A P32-37F32 9062330 3.1" 9060582 2.5 1.69 1/2 .0 9061817 3. A Thread P08 .75 9061884 1.0. A Thread P08 .2.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).83 3/4 .70 1 1/4 .63 P20 .25 9061815 1.14 1.1 1/4" 9062021 2. All Rights Reserved.50 1 5/8-12 UN P24 .00 2 1/2-12 UN * Threaded end conforms to SAE J1926/1 (O-ring straight thread adapter) MAS-3000-ADPT-PXX-XX SAE (M) Fitting Size PXX-XX (M) Piece Number Take Out.63 1 5/16-12 UN-2A P20-37F20 9062152 2.84 3/4-16 UNF-2A P12-37F12 9062327 2.00 3/4 -16 UNF P12 . 13 P32 9062268 3.1 1/4" 9061925 1. A P16-1/2" 9061612 2.1/2" 9061787 1.40 1.508-10 UNS-2A 3. A Thread Across Flats P08 9062267 1.68 Fitting Size PXX Piece Number Take Out. A Thread P12-37F08 9062331 1.85 3/4-16 UNF-2A P16-37F08 9062333 1.46 1 1/16-12 UN-2A P20-37F16 9062334 2.00 P16 .97 3/4-16 UNF-2A P16-37F12 9062332 2.00 P32 .00 P12 . Uthreads MAS-3000-RADPT-PXX-37FYY Fitting Size PXX-37FYY Piece Number Take Out.65 1.72 1 5/8-12 UN-2A P32-37F24 9062336 3.00 P24 .69 1 5/16-12 UN-2A P24-37F20 9062335 2.33 1 7/8-12 UN-2A * Threaded end conforms to SAE J514 (37º FLARE) MAS-3000-ADPT-PXX-XX NPS Fitting Size PXX-XX NPS Piece Number Take Out.com Copyright 2003 Lokring Technology Corporation.00 Take - Out.1 1/2 " 9061926 1.482-14 UNS-2A 1.80 1.2 " 9062521 1.52 1. Page 4 of 11 .70 1. A P06 .00 P08 .1" 9061789 1. Reducer Bushings.55 3.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).lokring.3/8" 9061924 1.59 1.00 MAS-3000-UTHREAD (400 WOG) PXX *Thread and seal face per MIL-F-1183 www. 6.34 1.00 P20 . B * Non LOKRING™ end made to match up with 6000 lb socket weld adapter MAS-3000-REDB-PXX-YY Fitting Size PXX-YY NPS Piece Number Take Out. TECHNOLOGY CORPORATION Adapters.3/4" 9061788 1. All Rights Reserved.46 1. 53 P12 9060423 2.51 P32 9060443 3.71 P12 9060425 2.96 P12 9061331 3.55 Fitting Size Pxx Piece Number Take Out.17 Fitting Size PXX Piece Number Take Out.16 P16 9061332 3.91 P20 consult Lokring P24 9061328 4.72 P16 9060429 2.82 P32 9061334 4. A P08 9061325 3.33 P32 9061329 5.lokring. Page 5 of 11 . A P08 9060417 2. Flanges TECHNOLOGY CORPORATION MAS-3000-FLNG150-PXX Fitting Size PXX Piece Number Take Out. A P08 9061330 2.com Copyright 2003 Lokring Technology Corporation.46 P20 consult Lokring P24 9061333 3.21 P20 9061288 3.26 P32 9060441 3.92 MAS-3000-FLNG300-PXX MAS-3000-FLNG600-PXX MAS-3000-FLNG1500-PXX www.27 P12 9061326 3.00 P24 9060435 3. A P08 9060419 2.31 P24 9060437 3.59 P48 9061371 4.34 P48 9061370 3.01 P48 9061372 4.91 P16 9060431 3.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04). 6. All Rights Reserved.96 P20 9061287 3.64 P16 9061327 3.11 P48 9061373 5.80 Fitting Size PXX Piece Number Take Out. 41 P24 9041829 2.55 P16 9060569 0.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).54 P32 9041864 2.48 P48 9041831 2.82 P32 9060573 2.lokring.25 P24 9060571 0. A P06 9041801 N/A P08 9041802 N/A P12 9041803 N/A P16 9060462 N/A P20 9061290 N/A P24 9060461 N/A P32 9060460 N/A P48 9041869 N/A *LOKRING's Carbon Steel Repair Couplings are slip over couplings made without an internal stop in order to facilitate repair work. All Rights Reserved. A P08 9041859 2.28 P12 9041860 2. O-ring per SAE J120 and hardware included MAS-3000-SAE61-PXX Fitting Size PXX Piece Number Take Out.25 P20 9041862 2. A P08 9060565 0. They consist of a stainless steel body with carbon steel drive rings.04 P16 9041861 2. MAS-3000-CAP-PXX Fitting Size PXX Piece Number Take Out. Caps.28 P12 9041826 2. Page 6 of 11 . TECHNOLOGY CORPORATION Repair Couplings.com Copyright 2003 Lokring Technology Corporation. 6.34 P48 9061616 3.93 MAS-3000-SAE61KIT-PXX *Non LOKRING end conforms to SAE J518 code 61 Split flange.05 Fitting Size PXX Piece Number Take Out.04 P16 9041827 2.53 P12 9060567 0.73 P20 9061289 2.48 P48 9041865 2.93 *Non LOKRING end conforms to SAE J518 code 61 Split flange and hardware NOT included www.41 P24 9041863 2.25 P20 9041828 2. A P08 9041825 2.54 P32 9041830 2. their pressure ratings are the same as those of LOKRING's stainless steel SS40 pipe fittings. SAE61 MAS-3000-RCPL-PXX Fitting Size Pxx Piece Number Take Out. SAE61KIT. 38 P20 9041872 2. O-ring per SAE J120 and hardware included MAS-3000-SAE62-PXX Fitting Size PXX Piece Number Take Out.47 *Non LOKRING end conforms to SAE J518 code 62 Split flange and hardware NOT included MAS-3000-SAE62SLD-PXX Fitting Size PXX Piece Number Take Out. TECHNOLOGY CORPORATION SAE61SLD.31 P20 9041877 2. SAE62.com Copyright 2003 Lokring Technology Corporation.12 P16 9041876 2.14 P20 9041855 2. SAE62KIT.31 P20 9041882 2.47 P24 9041873 2.68 P32 9041857 2.72 P16 9041854 2. A P08 9041852 1.72 P32 9041884 3. A P12 9041880 2. SAE62SLD MAS-3000-SAE61SLD-PXX Fitting Size PXX Piece Number Take Out.72 P32 9041879 3. Page 7 of 11 .50 P24 9041878 2.32 *Non LOKRING end conforms to SAE J518 code 62 solid (tapped holes) www.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04). A P12 9041870 2.50 P24 9041883 2.19 P24 9041856 2.08 P16 9041871 2.72 P12 9041853 1.47 *Non LOKRING end conforms to SAE J518 code 62 Split flange. All Rights Reserved. A P12 9041875 2. 6.98 P32 9041874 3.12 P16 9041881 2.84 P48 9041858 3.lokring.37 *Non LOKRING end conforms to SAE J518 code 61 solid (tapped holes) MAS-3000-SAE62KIT-PXX Fitting Size PXX Piece Number Take Out. TECHNOLOGY CORPORATION 45º Elbows. B Thread Across Flats P20 9062150 1.75 2. 45º Reducing Elbow Adapters. A Take Out. Fitting Size PXX Piece Number Take Out.94 P32 9060439 2.lokring. All Rights Reserved. A P08 9061396 1.5 *Threaded end conforms to female NPT thread MAS-3000-REL45-PXX-37FXX Fitting Size PXX Piece Number Take Out.21 P48 9061368 3.97 1 5/8-12 1. 90º Elbows MAS-3000-EL45-PXX Fitting Size PXX Piece Number Take Out.75 P24 9060433 1. Page 8 of 11 .54 6. B Thread P20-1 1/4 9062316 1.77 1-1/4 .28 P12 9060421 1. A P08 9060415 1.61 P20 9061284 1.com Copyright 2003 Lokring Technology Corporation.75 2.11.20 * Dimension of 1.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04). A Take Out.72 may be furnished at manufacturer's option MAS-3000-EL45-PXX-YY FPT Fitting Size PXX-YY FPT Piece Number Take Out.69 * Threaded end conforms to SAE J514 (37º FLARE) MAS-3000-EL90-PXX www.62 P12 9061203 1.41* P16 9060427 1. 00 C* C* Maximum cut on pipe end www.84 P48 9061369 5. 90º Elbows. A Take Out.27 P20 9061285 2.15 P12 9061947 1. B Thread NPT P12-1/4 9061735 1.lokring.06 7.63 3.42 may be furnished at manufacturer's option MAS-3000-EL90-PXX-YY FPT Fitting Size PXX-YY FPT Piece Number Take Out. All Rights Reserved.63 P24 9061192 3. A B P24 9062322 3.34 0.61 P48 9062386 5.50 4.07 P32 9060974 3.Out..55 13.69 * Threaded end conforms to SAE J514 (37º FLARE) MAS-3000-SEL90-PXX Fitting Size PXX Piece Number Take .75 1/4-18 *Threaded end conforms to female NPT thread MAS-3000-REL90-PXX-37FXX Fitting Size Pxx Piece Number Take Out.66 2.Take .85 1 5/8-12 1.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04). A Take Out. 90º Elbow Adapters. B Thread Across Flats P20 9062151 2.79* P16 9061145 2.com Copyright 2003 Lokring Technology Corporation. A P08 9061946 2. 6. Street Elbows TECHNOLOGY CORPORATION MAS-3000-EL90LR-PXX Fitting Size PXX Piece Number Take Out. Out. Page 9 of 11 .55 * Dimension of 1. A P08 9061397 1. B P24 9062389 3.62 P12 9061401 1. Page 10 of 11 .54 MAS-3000-TEESR-PXX www.66 *Non Lokring end conforms to SAE J518 code 61 c/w O-ring groove and thru holes MAS-3000-SAE62EL90-PXX Fitting Size PXX Piece Number Take Out.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).com Copyright 2003 Lokring Technology Corporation. Reducing Tees MAS-3000-SAE61EL90-PXX Fitting Size PXX Piece Number Take Out. TECHNOLOGY CORPORATION 90º SAE 61 Eblows. A Take Out.28 1.34 P48 9061367 4.05 1.65 P12 9061949 1.28 1. 6.lokring.07 P32 9060602 3.43 Fitting Size PXX Piece Number Take Out. All Rights Reserved.27 P20 9061286 2. A Take Out.31 P32 9062520 3.78 P16 9061144 2.66 *Non Lokring end conforms to SAE J518 code 62 c/w O-ring groove and thru holes MAS-3000-TEE-PXX Fitting Size PXX Piece Number Take Out. Tees. B P24 9062392 3. A P08 9061948 1.63 P24 9061191 3. 20 P48-P12 9061618 4.27 2.35 3.35 3.com Copyright 2003 Lokring Technology Corporation.04 P20-P16 9061292 2.65 P32-P12 9060605 3.66 P32-P16 9060604 3. A Take Out.32 *Drop conforms to ASME/ANSI B16.63 3. Tee Adapters TECHNOLOGY CORPOR ATION MAS-3000-RTEE-PXX-PYY XX XX YY Fitting Size PXX-PYY Piece Number Take Out.91 P24-P16 9061403 3. B Thread P20-1.72 P24-P08 9061399 3. All Rights Reserved. Page 11 of 11 .39 P48-P16 9061617 4.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04).15 P16-P12 9061343 2.63 2.34 3.34 2. 6.07 2.01 P16-P08 9061344 2.50 P48-P24 9061615 4.77 P32-P24 9060603 3.63 3. B P12-P08 9061398 1.07 2.07 3.lokring.34 2.25 SAE 9062153 2.43 5.54 2.34 2.5 150 lb flange www.75 P48-P32 9061408 4.26 Fitting Size PXX-YY SAE Piece Number Take Out. Reducing Tees. A Take Out.35 3.27 2.16 P20-P12 9061632 2.78 2.90 P24-P12 9061402 3. A Take Out.12 UN-2B MAS-3000-REDTLR-PXX-PYY (LONG RADIUS REDUCING TEE) XX XX YY MAS-3000-RTEE-PXX-YY SAE *Drop conforms to SAE J1926/1 MAS-3000-RTEE (FLNG)-PXX-PYY Fitting Size PXX-YY Piece Number Take Out.02 P32-P08 9060975 3.37 1-5/8 . A Take Out. B P12-P08 9061951 1.35 3.78 Fitting Size PXX-PYY Piece Number Take Out. B P48-1-1/2" 9062206 4. Cross …………… Page 13 Copyright 2003 Lokring Technology Corporation. Utails …………… Page 5 Uthreads. Reducers …………… Page 2 Reducers. Caps …………… Page 7 SAE Fittings. T E C H N O L O G Y C O R P OR A T I ON SS40 STAINLESS STEEL PIPE FITTINGS www. Tees …………… Page 9 Reducing Tees. Flanges …………… Page 6 Flanges. 90º Elbows …………… Page 8 90º Elbows. Adapters …………… Page 3 Adapters. 45º Elbows. 6. Reducer Bushings.com General Information …………… Page 1 Couplings. Unions. Drop Tees …………… Page 10 Drop Tees. Tee Adapters. Clean in Place. Double Reducing Tees.lokring.02 SS40 Stainless Steel Pipe Fittings (02-23-04) . 90º Elbow Adapters. All Rights Reserved. Obtuse Tees. Uthreads. 5.44 1. 4.94 1. contact Lokring for details 8. 3.39 3.72 1. All dimensions are in inches.49 0. All other fittings (tees.56 1.41 4. 7. B Outside Diameter.92 3.33 2.69 2.33 1 1/2" (P24) 10/ 40/ 80 2. 6.90 2.04 2.56 1.86 2. 2.41 3. All Rights Reserved.64 2" (P32) 10/ 40 3. For tooling dimensions refer to appropriate catalog. Other part configurations than those shown and custom configurations may be available.52 1" (P16) 10/ 40/ 80 2.24 3/4" (P12) 10/ 40/ 80 1. Autocad-DXF and Intergraph PDS are available for most configurations.68 3.05 2.28 0. 6. C. Page 1 of 13 .05 1.08 1/2" (P08) 10/ 40/ 80 1.86 1 1/4" (P20) 10/ 40/ 80 2. Fitting material 316L Stainless Steel as per ASTM A276 or ASTM 479.lokring. Coupling "thru-bore" design permits tube to pass completely through. elbows etc.53 6. 316L stainless steel pipe as per ASTM A312 and carbon steel pipe as per ASTM A53 or A106.66 1.07 2.63 1.60 1. CAD files in Autocad-DWG. See table for qualified wall thickness. D Minimum Straight Run Before a Bend.71 3.12 1. Dimensions A.com Copyright 2003 Lokring Technology Corporation.37 1.) have an internal travel stop. contact Lokring™ for details 9.95 3" (P48) 10/ 40/ 80 4.11 2.80 2. For use on 316.20 1.18 1. General Information T E C H N O L OG Y C OR P O R A T I ON PRE-INSTALLED POSITION POST-INSTALLED POSITION Fitting Size (PXX) Qualified Wall Thickness Insertion Depth PreInstall. E 1/4" (P04) 10/ 40/ 80 1. C Inside Diameter. B.45 1.29 1. D & E are applicable to all fittings of the same size within this catalog.02 SS40 Stainless Steel Pipe Fittings (02-23-04). A Insertion Depth PostInstall.06 0. All dimensions are reference only and subject to change www.89 3/8" (P06) 10/ 40/ 80 1.96 1.50 3.61 1. 90 P20-P16 9061301 1. Reducers T E C H N O L O G Y C OR P OR A T I ON SS40-CPL-PXX Fitting Size PXX Piece Number Take Out P04 9062176 n/a P06 9062177 n/a P08 9040043 n/a P12 9040106 n/a P16 9040107 n/a P20 9041293 n/a P24 9040103 n/a P32 9040108 n/a P48 9041868 n/a P48** 9041832 n/a **Coupling with zinc plated carbon steel drive rings is available at lower cost SS40-CPL-MXX (METRIC PIPE COUPLING) Fitting Size MXX Piece Number Take Out M12 9062377 n/a M14 9041850 n/a M15 9062199 n/a Fitting Size PXX-PYY Piece Number Take Out.67 P12-P08 9061270 0. A M15-M14 9062200 0.61 Fitting Size MXX-MYY Piece Number Take Out.83 P16-P08 9061271 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04).02 P16-P12 9061272 0.07 P32-P20 9062273 1. A P08-P06 9061610 0.88 P32-P16 9061274 2.com Copyright 2003 Lokring Technology Corporation.04 P24-P12 9061345 1.50 P48-P32 9061878 4.lokring.70 P24-P20 9061848 0. 6.52 SS40-RED-PXX-PYY SS40-RED-MXX-MYY (METRIC CONCENTRIC REDUCER) www.24 P48-P16 9061880 4.85 P24-P16 9061273 1. All Rights Reserved. Couplings. Page 2 of 13 .77 P32-P24 9061275 1. 66 P16-T08 9041866 0.11.1 1/2 9061767 0.26 1.1/4 consult Lokring 0.11.84 P20-T24 9061347 0.69 1/4-18 P06 .5 Copyright 2003 Lokring Technology Corporation.1/2 9061763 0.90 0.94 3/8 .3/4 9061764 0. Page 3 of 13 .38 2 .95 1.3/8 9061762 0.12 3/4-14 P16-1 9061259 2.37 1 .5 P20-1 1/4 9061746 2.62 2.06 1 1/2-11.5 Fitting Size PXX-XX MPT Piece Number SS40-ADPT-PXX-XX MPT www. Reducers.14 P12 .93 2.64 P20-T20 9062149 0.lokring. All Rights Reserved. A Flats Thread NPT P04-1/4 9061744 1.60 0.1 9061765 0.75 3/8-18 P08-1/2 9061261 1.1 1/4 9061766 0. A P12-T12 9062256 0.Across Out.5 P24 .13 1/2 .31 3/4 .19 Fitting Size MXX-PYY Piece Number Take Out.18 P06-3/8 9061745 1.Across Out.75 1 1/4 -11.18 P08 .11.88 1 1/4 -11.00 1 1/2 -11.80 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04).37 1.91 1.93 1.5 P24-1 1/2 9061258 2.53 2.45 0. 6.63 1/4 .58 Fitting Size PXX-XX FPT Piece Number P04 .50 1 .5 P32-2 9061257 2.94 1/2-14 P12-3/4 9061260 1.46 0. Adapters T E C H N O L OG Y C OR P OR A T I ON SS40 & SS-3000-RED-PXX-TYY (PIPE TO TUBE REDUCER) Fitting Size PXX-PYY Piece Number Take Out.14 SS40-RED-MXX-PYY (METRIC TO PIPE REDUCER) SS40-ADPT-PXX-XX FPT Take .40 M14-P08 9041851 0. A M14-P04 9062264 0.84 P32-T32 9062102 1. C Flats Thread NPT P16 .5 P20 .78 1.58 0.com Take . 0 9061943 2.67 * Non LOKRING™ end made to match up with 6000 lb socket weld adapter www.5 9061942 1.17 2.63 1.73 1.00 1.20 1.40 P12 . A Across Flats Thread NPT P04-1/2 9062376 1.5 9061940 0.00 9061932 1.2 9061944 1.3/8 9061921 1. A Across Flats P08-37F08 9062397 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04).00 1. All Rights Reserved.02 1. Page 4 of 13 .25 1 7/8-12 P32-2.39 1.14 P16 .1 1/2 9061923 1.37 1 -11.64 3.46 P16 .00 1.1 1/4 9061769 2.com Copyright 2003 Lokring Technology Corporation.3/4 9061768 1.00 1.44 1 1/16-12 P16-1.69 1 5/8-12 *Threaded end conforms to SAE J514 (37° Flare) SS40-ADPT-PXX-XX NPS Fitting Size PXX-XX NPS Piece Number Take Out.60 1.13 1 1/16-12 * Threaded end conforms to SAE J514 (37º FLARE) SS40-RADPT-PXX-37FYY Fitting Size PXX-37FYY Piece Number Take Out.14 P20 .52 P20 .13 3/4-16 P12-37F12 9062271 1.00 1.5 Thread UN *Threaded end conforms to male NPT thread SS40-ADPT-PXX-XX SAE Fitting Size PXX-XX SAE Piece Number Take Out.59 P24 .45 0. A Across Flats Thread UN P12-37F08 9062396 1.lokring.12 3/4 .13 3/4-16 P16-37F12 9061771 1.24 1.87 1/2 .75 9061931 1.06 3/4-16 P12-0.14 P12-1/2 9062101 1.63 1 5/16-12 P20-1.1 9061786 1.18 1.71 1.82 0.38 1 5/16-12 P24-37F20 9601773 1. B P06 .13 1 1/16-12 P20-37F16 9061772 1.3/4 9061783 1.65 P32 .00 1.34 P08 . A Take Out.37 2. Adapters T E C H N O L O G Y C OR P OR A T I ON SS40-RADPT-PXX-YY MPT Fitting Size PXX-YYMPT Piece Number Take Out.75 1 1/4-11.1 9061770 2.00 2 1/2-12 Thread UN *Threaded end conforms to SAE J1926/1 (O-ring straight threaded adapter) SS40-ADPT-PXX-37FYY Fitting Size PXX-37FYY Piece Number Take Out.95 1.82 1.1 1/4 9061922 1.00 1 5/8-12 P24-1.88 1/2 .5 P24 . 6.1/2 9061785 1.25 9061941 1.36 1.72 1. A Across Flats P08-0. 28 2 -12UN 2-1/4 P16 9061588 1.56 P16-1 1/4 9061238 4.25 1-3/4-12UN 2 P12 9061586 1.11.98 P08-1 9061236 3.40 3-1/16-12NS 3-1/2 P32 9061594 1. Uthreads.5 1 1/4 x 1 1/4 9061267 5.61 3-3/4-12UN 3-3/16 SS40-UTHRD-PXX *Thread and seal face conform to Navy dwg 803-1385884 SS40-UTAIL-PXX Fitting Size PXX Piece Number Take Out.02 2. 6.07 SS40-REDB-PXX-YY NPS P16 .12 3/4 -14 1x1 9061266 4.11.46 P20-1 1/2 9061335 4.00 1 1/2-11.69 2 -12UN 1-5/8 P16 9061587 1. Page 5 of 13 .28 2-5/16-12NS 2-9/16 P20 9061590 1.89 2.41 Fitting Size PXX Piece Number Take Out.12 P16-1 1/2 9061239 5.11 2-3/4-12UN 2-3/8 P24 9061591 2.02 SS40 Stainless Steel Pipe Fittings (02-23-04).93 1. A Thread NPT 1/2 x 1/2 9061264 3. Adapters. A P06-1/2 9062173 2. All Rights Reserved.22 P24-2 9061240 6.67 P12-1 9061237 3. A Thread Across Flats P04 9061580 1.77 0.58 1-3/16-12UN 15/16 P06 9061582 1.66 1-3/4-12UN 1-1/4 P12 9061585 1.com Copyright 2003 Lokring Technology Corporation.38 2 .43 3-1/16-12NS 2-5/8 P32 9061593 2.30 1-3/8-12UN 1-5/8 P08 9061613 1.24 1-3/16-12UN 1-3/8 P06 9061583 1.46 3-3/4-12UN 4-1/8 *Complete with BUNA-N O-Ring *Thread and seal face conform to Navy dwg 803-1385884 www.64 1-3/8-12UN 1-1/6 P08 9061584 1.10 1. Reducer Bushings.14 3/4 x 3/4 9061265 4.5 Fitting Size PXX-YY NPS Piece Number Take Out.5 2x2 9061269 6.5 1 1/2 x 1 1/2 9061268 5.33 2-3/4-12UN 3 P24 9061592 1.2 9061241 5.37 1 .94 2-5/16-12NS 2 P20 9061589 2.lokring. Utails TECHNOLOGY CORPORATION SS40-ADPT-XX NPS-YY MPT Fitting Size XX-YY Piece Number Take Across Flats Out.75 1 1/4-11.87 1/2 .54 P08-3/4 9061235 2.45 1. A Thread Across Flats P04 9061581 1. 22 2-5/16-12NS P20 9061461 3.75 **Flange with zinc plated carbon steel drive ring is available at lower cost * Flange conforms to ASME/ANSI B16. A P12-1.lokring. A P08 9060264 2. Flanges TECHNOLOGY CORPORATION SS40-RUTAIL-PXX-YY Fitting Size PXX-YY Piece Number Take Out. All Rights Reserved.67 P24 9061215 2. Unions.20 Fitting Size PXX Piece Number Take Out.57 P20 9061297 2.59 * Flange conforms to ASME/ANSI B16.68 P48** 9061726 3.5.75 P48** 9061727 3. A P32-1-1/2 9061559 3. 6. 300 LB www.97 2 -12UN P16 9061460 3.23 P48 9061680 3. Uthreads.02 SS40 Stainless Steel Pipe Fittings (02-23-04).98 P48 9061679 3. A P08 9060052 2. Page 6 of 13 .63 P16 9061232 2.23 P12 9061214 2.00 9061596 1.07 3-3/4-12UN SS40-UNION-PXX *Complete with BUNA-N O-Ring *Thread and seal face conform to Navy dwg 803-1385884 SS40-FLNG150-PXX Fitting Size PXX Piece Number Take Out.68 **Flange with zinc plated carbon steel drive ring is available at lower cost * Flange conforms to ASME/ANSI B16.98 P24 9061233 3.5.87 P32 9061224 2.5.82 P20 9061298 2.91 1-3/4-12UN P12 9061459 2.83 3-1/16-12NS P32 9061463 4.41 P12 9061231 2.com Copyright 2003 Lokring Technology Corporation.44 2-3/4-12UN P24 9061462 3.12 P32 9061234 3.82 1-3/16-12UN P06 9061457 2.44 P16 9061219 2. 150 LB SS40-FLNG150-P32-1 1/2" Fitting Size PXX-XX Piece Number Take Out. 150 LB SS40-FLNG300-PXX Fitting Size PXX Piece Number Take Out.94 1-3/8-12UN P08 9061458 2. A Thread P04 9061456 2. 82 P20 9061323 3.91 P16 9061254 1. A P08 9061256 0.63 P16 9061322 2.5. A P08 9062379 2.95 P32-2 9062280 1.11 P24 9061253 1. Page 7 of 13 .29 P48 9062178 2.22 P32 9061252 1.36 P48 9061681 3. Flanges.15 Fitting Size PXX Piece Number Take Out.41 P12 9061321 2.88 P48** 9061728 3. 1500 LB SS40-CIP-PXX-YY Fitting Size PXX-YY Piece Number Take Out. All Rights Reserved. 600 LB SS40-RTJ1500-PXX Fitting Size PXX Piece Number Take Out.com Copyright 2003 Lokring Technology Corporation. A P16-1 9061683 0.5. A P08 9061320 2.88 **Flange with zinc plated carbon steel drive ring is available at lower cost * Flange conforms to ASME/ANSI B16. 6.85 P12 9061255 0.lokring.63 SS40-CAP-PXX www. Caps TECHNOLOGY CORPORATION SS40-FLNG600-PXX Fitting Size PXX Piece Number Take Out.93 P24-2 9061654 0.04 P20 9061299 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04).98 * Flange conforms to ASME/ANSI B16.04 P24 9061324 3.18 P32 9061342 3.96 P20-1-1/2 9061685 0. Clean in Place. 13 may be furnished at manufacturer's option **Elbow with zinc plated carbon steel drive rings is available at lower cost SS40-EL90-PXX www.15 P06 9061394 1.86 P48 9061678 2.25 P20 9061294 1. A P08 9062345 2.05 P12 9062346 1.09 Fitting Size PXX Piece Number Take Out.63 SS40-SAE61-PXX SS40-EL45-PXX * Dimension of 1.08 P24 9062349 2. A P08 9062350 2.com Copyright 2003 Lokring Technology Corporation. Fitting Size PXX Piece Number Take Out.63 P48** 9061725 2.84 P16 9062352 1.15 P08 9060040 1.98 P12 9061212 0.82 * P16 9061007 1.lokring. SAE61KIT. A P04 9061393 1.83 P20 9062353 2.05 P12 9062351 1. 90º Elbows TECHNOLOGY CORPORATION SS40-SAE61KIT-PXX Fitting Size PXX Piece Number Take Out.56 P32 9061227 1. A P04 9061608 1.13 6.02 P06 9061607 0.09 Fitting Size PXX Piece Number Take Out.08 P24 9062354 2.42 P24 9061213 1. Page 8 of 13 .95 P08 9060180 0.83 P20 9062348 2. SAE61.84 P16 9062347 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04). 45º Elbows. All Rights Reserved. 66 2.13 P12 9061216 1.0. A Out.lokring. 6. A Out.5 9061833 1.14 P24 . 90º Elbow Adapters.91 C* C* Maximum cut on pipe end SS40-TEE-PXX Fitting Size PXX Piece Number Take Out.13 P48** 9061724 5. Street Elbows.61 P32 9061958 3.88 * P16 9061210 1.68 P32 9061226 3.com Copyright 2003 Lokring Technology Corporation. TECHNOLOGY CORPORATION 90º Elbows.48 P48 9061676 5.30 P24 9061218 2.13 2.30 P24 9061211 2.68 P32 9061225 2.00 **Tee with zinc plated carbon steel drive rings is available at lower cost www.68 7. B P24 9061409 2.14 *Threaded end conforms to female NPT thread SS40-SEL90-PXX Fitting Size PXX Piece Number Take .13 * Dimension of 1. B Thread NPT P08 . All Rights Reserved.10 P08 9061012 1.Take Out.95 2.48 8.88 P20 9061296 2.Take Out. A P04 9061389 1.50 may be furnished at manufacturer's option **Elbow with zinc plated carbon steel drive rings is available at lower cost SS40-EL90SR-PXX-XX FPT Fitting Size PXX-XX FPT Piece Number Take ..10 P06 9061390 1.00 P48** 9061723 4.26 P16 9061217 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04). Tees SS40-EL90LR-PXX Fitting Size PXX Piece Number Take Out P12 9061209 1.5 9061865 1. Page 9 of 13 .0.16 1/2 .44 1/2 .98 P48 9061677 4.88 P20 9061295 2.09 1. 88 P24-P12 9061346 2.38 P32-P24 9061247 2. A Out.98 3.13 P12-P04-P08 9061564 1.63 P32-P12 9061362 2. B 2.20 P32 .Take Out.88 2.02 2.Take Out.10 P12-P04 9061562 1.30 SS40-RTEE-PXX-TYY (PIPE TO TUBE REDUCING TEE) Take .98 2.30 2.52 P32-P16 9061246 2.98 3.26 1.68 2.26 P48-P32 9061682 4.02 P20-P16 9061300 2.68 2.00 3.13 1. Double Reducing Tees.98 2.75 1.Take Out.38 1.lokring.98 2.Take Out.com Copyright 2003 Lokring Technology Corporation.48 Fitting Size PXX-TYY Piece Number P20-T12 9061791 Fitting Size PXX-PYY-PZZ Piece Number P08-P04-P08 9061563 1.13 1.02 SS40 Stainless Steel Pipe Fittings (02-23-04). Reducing Tees. All Rights Reserved.79 3.63 P24-P20 9061361 2.02 P24-P16-P16 9061569 2.68 2. Drop Tees TECHNOLOGY CORPORATION SS40-RTEE-PXX-PYY XX XX YY Fitting Size PXX-PYY Piece Number Take .00 P32-P20-P20 9062276 2.26 1.68 3.00 3. B 6. Page 10 of 13 . A Out.68 2.26 1.88 2.87 XX XX YY SS40-RRTEE-PXX-PYY-PZZ YY XX ZZ Take .28 P12-P08 9061242 1.P04 9061747 1.13 P16-P12 9061223 1.98 3.33 1.P12 9062134 2. C SS40-DTEE-PXX-PYY www.26 2. A Out.30 2. Take .88 2.26 1.33 P16-P12-P08 9061572 1.52 Fitting Size PXX-PYY Piece Number P24 .79 P32-P24-P12 9061567 2.33 P12-P08-P08 9061570 1.77 P24-P16 9061245 2. B Take Out.13 P16-P12-P12 9061571 1.88 1.88 2.50 P24-P08 9061743 2.17 1.70 P32-P08 9061566 2. B P08-P04 9061561 1.33 P16-P04 9061565 1. A Out.17 P08-P06 9061609 1.13 1.88 2.02 2.64 P16-P08 9061243 1. Take Out.98 3.Take Out.95 3. Drop Tees TECHNOLOGY CORPORATION SS40-TEE-PXX-001 [3/8 OD X 0. A Out.049 WALL TUBE DROP] Take . C P16 9061750 1.09 1. ** P16 and P20 Sizes are available without an internal travel stop www. Page 11 of 13 .06 * CPI is a trademark of PARKER HANNIFIN CORPORATION.63 SS40-TEE-PXX-002 [3/8 OD SWAGELOK ® DROP*] Take .31 1. SS-3000-TEE-PXX-TYY-002 [3/8 OD SWAGELOK ® DROP*] Fitting Size PXXTYY Piece Number Take .94 * SWAGELOK is a registered trademark of SWAGELOK CO. B P16-T16 9061697 Fitting Size PXX Piece Number P08 9061466 0. C 0. C P16 9061695 1.31 1.Take Out.11 2.09 3. A Out.09 1.52 P16 9062509 1.Take Out.93 P24 9062140 1.77 P20 9062137 1.09 Take .11 4. C SS40-TEE-PXX-005 [3/8 OD CPI DROP*] Take .78 SS40-TEE-PXX-003 [1/2 OD X 0.02 SS40 Stainless Steel Pipe Fittings (02-23-04).Take Out.Out. 6. A Out.31 3.81 P20 9061465 1.34 4.98 P24 9062510 1.78 P20 9061696 1.com Copyright 2003 Lokring Technology Corporation.32 Fitting Size PXX Piece Number 1. C 0.lokring. A Out.10 P32 9061464 1. A Out.90 1.035 WALL TUBE DROP] Fitting Size PXX Piece Number P12 9062004 Fitting Size PXX Piece Number Take . All Rights Reserved. All Rights Reserved.83 P24 9061751 1.66 * CPI is a trademark of PARKER HANNIFIN CORPORATION.Take Out.Take Out.lokring.93 SS-3000-TEE-PXX-TYY-005 [3/8 OD CPI DROP*] [PIPE TO TUBE] Take .31 1.Take Out.09 0. SS40-TEE-PXX-009 [1/2 OD SWAGELOK® DROP*] Fitting Size PXX Piece Number Take . A Out.77 SS40-TEE-PXX-008 [1/2 OD CPI DROP*] Take . Drop Tees TECHNOLOGY CORPORATION SS40-RTEE-PXX-PYY-005 [3/8 OD CPI DROP*] [REDUCER] Fitting Size PXX-PYY Piece Number P20-P16 9061890 Fitting Size PXX-TYY Piece Number P16-T16 9061889 Fitting Size PXX Piece Number P16 9062145 Take . C 1.09 Take .09 1. C 1.Take Out. A Out.Take Out. Page 12 of 13 .73 6. A Out.Out. C P20 9061930 1. B 1.31 1.Out. C 1.11 1. Take .90 Take . B 1.96 Fitting Size PXX Piece Number P24 9062293 SS40-TEE-PXX-013 [1/2" FPT DROP] www. A Out. C 1. A Out.02 SS40 Stainless Steel Pipe Fittings (02-23-04).11 2.com Copyright 2003 Lokring Technology Corporation. 02 SS40 Stainless Steel Pipe Fittings (02-23-04).78 2.98 Fitting Size PXX-YY FPT Piece Number P20-3/4 9061777 SS40-OBTEE-PXX-PYY Take . A Out. A Out.Take Out. 6.26 Copyright 2003 Lokring Technology Corporation.72 P16 9061912 1. Cross TECHNOLOGY CORPORATION SS40-TEE-PXX-026 [12mm OD X 1mm WALL TUBE DROP] Fitting Size PXX Piece Number Take .Take Out.31 *Threaded end conforms to female NPT thread SS40-RTEE-PXX-YY SAE Fitting Size PXX-YY SAE Piece Number P08-9/16 SAE 9061606 Take . Obtuse Tees. C SS40-RTEE-PXX-YY FPT Take . A Out. Tee Adapters. Page 13 of 13 . All Rights Reserved.26 2. B 1.com Fitting Size PXX Piece Number Take Out.Take Out.81 Thread 9/16-18 UNF-2B *Drop conforms to SAE J1926/1 SS40-CROSS-PXX www.88 Fitting Size PXX-PYY Piece Number P32-P20 9062275 3. B 2. C P12 9061911 0. A P12 9061781 1. Drop Tees.98 P32-P24 9062277 3.00 Thread NPT Across Flats 3/4-14 1.lokring. A Out.98 2.09 2.13 1.Take Out.30 3. lokring. 6.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04) . Clean in Place …………… Page 3 Caps. 90º Elbows. All Rights Reserved. 45º Tees …………… Page 4 Reducing Tees. Reducers …………… Page 2 Adapters. Drop Tees …………… Page 5 Drop Tees …………… Page 6 Copyright 2003 Lokring Technology Corporation.com General Information …………… Page 1 Coupling. 45º Elbows. T E C H N O L OG Y C OR P O R A T I ON SS-3000 / SS40 STAINLESS STEEL TUBE FITTINGS www. 0.035 .882 2. B Outside Diameter.56 2.) have an internal travel stop.507 1.96 2. 6.065 .035 .065 0.60 2. elbows etc.17 0.065 .73 0.13 1.61 1.0. Coupling "thru-bore" design permits tube to pass completely through (except SS40-T04). All dimensions are reference only and subject to change www.22 1. 3.88 0.065 1. Page 1 of 12 .72 0.0.065 1.05 0.257 1.75 2" (T32) 0.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).00 1" (T16) 0.65 1.25 1.065 1.63 5/8" (T10) 0. 7.007 2. Other part configurations than those shown and custom configurations may be available. C Inside Diameter.26 0.54 0.81 1.11 1. contact Lokring™ for details 9. 4.083 1.109 2. See table for qualified wll thickness.00 0. Fittings from T04-T12 & T32 are SS40-Txx.06 1.12 1.87 0. E 1/4" (T04) 0.065 1. For use on 316.34 1.065 .17 1. 2.120 2.00 3/4" (T12) 0.14 1.com Copyright 2003 Lokring Technology Corporation. B.035 .757 2. 316L.63 1/2" (T08) 0. Material 316L Stainless Steel as per ASTM A276 or ASTM 479.20 0.382 1.035 .507 2. All Rights Reserved.083 2.38 1. For tooling dimensions refer to appropriate catalog.035 .065 . Dimensions A.lokring.007 3.92 0. All dimensions are in inches.00 1 1/4" (T20) 0. 6. Fittings from T14-T24 are SS-3000-Txx 8.065 .0.25 3/8" (T06) 0.0.53 1.632 2.50 1.00 7/8" (T14) 0.0. D & E are applicable to all fittings of the same size within this catalog. General Information T E C H N O L OG Y C OR P O R A T I ON PRE-INSTALLED POSITION POST-INSTALLED POSITION Fitting Size (TXX) Qualified Wall Thickness Insertion Depth PreInstall.0.0.0.0. 5.50 1 1/2" (T24) 0. 304 and 304L seamless and welded stainless steel tube as per ASTM A269 or A213.065 1. A Insertion Depth PostInstall.257 2. All other fittings (tees. D Minimum Straight Run Before a Bend.53 1.56 1. C. 13 T32-T24 9062119 1. Reducers T E C H N O L O G Y C OR P OR A T I ON SS40 & SS-3000-CPL-TXX Fitting Size TXX Piece Number Take Out *1/4" (T04) 9061800 0.66 P16-T08 9041866 0.64 T12-T10 9061983 0.16 T08-T04 9061779 0.com Copyright 2003 Lokring Technology Corporation.34 T16-T14 9061985 0.97 T08-T06 9061722 0.lokring.84 P32-T32 9062102 1.71 T16-T12 9062014 1. Coupling.70 T10-T08 9061982 0. SS40-DC-TXX (DOUBLE CONTAINMENT COUPLINGS) Fitting Size TXX Piece Number Span A T08 9060190 3.74 T12-T08 9060624 0.84 T32-T20 9062297 1. 6. A T06-T04 9061990 1.90 T24-T16 9060653 1. A P12-T12 9062256 0.64 P20-T20 9062149 0.53 T10 9040060 3.84 T20-T16 9061986 0. All Rights Reserved.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).84 P20-T24 9061347 0. Page 2 of 12 .74 T14-T12 9061984 0.00 T24-T20 9061987 0.57 Fitting Size TXX-TYY Piece Number Take Out.43 Fitting Size PXX-PYY Piece Number Take Out.04 3/8" (T06) 9061796 n/a 1/2" (T08) 9061797 n/a 5/8" (T10) 9061798 n/a 3/4" (T12) 9061799 n/a 7/8" (T14) 9040094 n/a 1" (T16) 9040072 n/a 1 1/4" (T20) 9040047 n/a 1 1/2" (T24) 9040046 n/a 2" (T32) 9062143 n/a *1/4" (T04) Fitting is made with a travel stop to aid with assembly.19 SS40 & SS-3000-RED-TXX-TYY SS40 & SS-3000-RED-PXX-TYY (PIPE TO TUBE REDUCERS] www. 25-T04 9061834 1.04 T24-1 1/2 9061687 1.46 2.75 1.38-T06 9061840 1.35 1.12 UN 1.09 1.00-T16 9061845 1.93 P24-2 9061654 0.26 0.28 1.25 1 3/16 .69 1 5/8 . Page 3 of 12 .15 0.16 UNF 0.25-T20 9061846 2.93 1.13 3/4 .18 UNF 0.75 9062123 1.94 7/8 . Take - Out.63 9/16 .12 UN 0.50-T24 9061829 1.95 P32 9062280 1.50 7/16 .44 1 1/16 . All Rights Reserved.00 2.12 UN 0.12 UN 1.25-T20 9061828 1.18 UNF 0.12 UN 1.75-T12 9061843 1. A P16-1 9061683 0.31 1.00 1.25-T04 9061839 1.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).44 1 3/16 .lokring.25 1.00 1 5/8 .15 6. Adapters.96 P20-1-1/2 9061685 0.92 0.78 1.97 Fitting Size PXX-YY Piece Number SS40-CIP-PXX-YY CIP FITTINGS [PIPE] www.50-T24 9061847 3.81 3/4 .14 UNF 0.50 9062124 1.01 0.88 1.88-T14 9061826 1.57 1. C T08 .0.00-T16 9061827 1.20 UNF 0. A T16-1 9061005 0.20 UNF 0.04 T32-2 9041891 0.12 UN Threaded end conforms to SAE J1926/1 (O-ring straight adaptor) SS40 & SS-3000-ADPT-TXX-37FYY Fitting Size 37FYY TXX- Piece Number Take A Out.12 UN 1.75-T12 9061825 1.13 1 1/16 .02 T16 .75 7/16 .25 7/8 .16 UNF 0.14 UNF 0.50-T08 9061841 1. A Take Out.29 0.88-T14 9061844 1. A Across Flats Thread 0.50 1.63 1 5/16 .17 0.38-T06 9061835 0.49 0.0.30 Fitting Size TXX-YY Piece Number SS40 & SS-3000-CIP-TXX-YY Take - Out. Clean in Place T E C H N O L OG Y C OR P OR A T I ON SS40 & SS-3000-ADPT-XXSAE-TYY Fitting Size XXSAETYY Piece Number Take Out. Across Flats Thread 0.85 T20-1 1/2 9062274 1.66 2.63-T10 9061837 1.00 1 7/8 .00 9062122 1.1.50 0.12 UN 1.38 1 5/16 .12 UN Threaded end conforms to SAE J514 (37° Flare) SS40 & SS-3000-ADPT-TXX-TYY Fitting Size TYY TXX- Piece Number Take - Out.63-T10 9061842 1. B Take Out.25 1 7/8 .12 UN 1.16 0.96 T12 .94 9/16 .com Copyright 2003 Lokring Technology Corporation.50-T08 9061836 1. 42 T32 9062144 0.88 T24 9060218 2. B Take Out.05 T12 9061961 1.43 3.09 T10 9061970 0.035 wall tube XX www.com Copyright 2003 Lokring Technology Corporation.71 Fitting Size TXX-TYY-TZZ Piece Number Take Out. A Take Out.17 T16 9061993 1.93 Fitting Size TXX-TYY-ZZ TUBE Piece Number Take Out.04 T14 9061992 1.71 SS40 & SS-3000-EL45-TXX SS40 & SS-3000-EL90-TXX SS-3000-LAT45-TXX-TYY-TZZ ZZ XX Take Out.42 T20 9062299 0.29 T32 9060575 3.20 T08 9061892 1. A T06 9061968 1.42 T24 9061199 0. Caps.90 T12 9061971 1.93 2.42 T32 9061996 2.lokring.49 Fitting Size TXX Piece Number Take Out. YY 6.02 T20 9060216 1. B YY SS40-LAT45-TXX-TYY-ZZ TUBE ZZ * Lateral 3/8 OD X 0.26 T24 9061995 1.41 T14 9061962 1.08 Fitting Size TXX Piece Number Take Out. A T16 9062298 0. A T06 9061959 1. 90º Elbows.55 T16 9061874 2.05 n/a T24-T24-T24 9061718 0. C T20-T16-3/8 9061795 0. 45º Elbows.01 T10 9061960 1.39 T20 9061994 1.18 T08 9061969 1. All Rights Reserved. Page 4 of 12 . 45º Tees T E C H N O L O G Y C OR P OR A T I ON SS40 & SS-3000-CAP-TXX Fitting Size TXX Piece Number Take Out.26 3. A T24-T20-T20 9061719 1.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04). 30 1. B T06-T04 9061991 1.15 1. Drop Tees T E C H N O L O G Y C OR P O R A T I ON SS40 & SS-3000-TEE-TXX Fitting Size TXX Piece Number Take - Out.30 T20 9060217 1.21 3.17 T16-T14 9061976 1. Page 5 of 12 .30 1.29 2.31 T16 9061736 1.94 2.96 T10 9061965 1.34 T14-T12 9061975 1.42 T08-T06 9061972 0. A Take Out. A Take Out.88 T24 9060219 2. 6.17 T16-T08 9061686 1. All Rights Reserved.15 T10-T08 9061973 1.lokring.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).94 T24-T16-T24 9062252 2.21 Fitting Size TXX-TYY Piece Number Take Out.31 T20-T16 9061977 1.29 T32 9062109 3.05 1. C T24-T16-T16 9062251 2.29 SS40 & SS-3000-RTEE-TXX-TYY XX XX YY SS40-RTEE-PXX-TYY (PIPE TO TUBE REDUCING TEE) XX XX YY SS-3000-RRTEE-TXX-TYY-TZZ YY XX ZZ www. B Take Out.17 1.17 2.29 2.29 2.com Copyright 2003 Lokring Technology Corporation.22 Fitting Size PXX-TYY Piece Number Take Out.94 T24-T20 9061978 2. A Take Out.30 1.05 T12 9061790 1.74 Fitting Size TXX-TYY-TZZ Piece Number Take Out.96 1.41 T14 9061966 1.24 T12-T10 9061974 1.88 2.31 1. A T06 9061866 1. B P20-T12 9061791 2.29 2.53 T16-T12 9061809 1.29 T32-T24 9061979 3.15 T08 9061599 0.02 T24-T16 9062250 2.94 2. Reducing Tees. com Copyright 2003 Lokring Technology Corporation.63 Fitting Size TXX Piece Number Take Out.85 0.26 T10-T08 9060288 0.21 T10 9061050 0.96 0.54 T20-T16 9060167 0.40 T14 9061058 0. Take Out.85 0. Page 6 of 12 .89 3.26 T10 9061056 0. www.86 T24-T20 9060166 0.70 T24-T16 consult Lokring 0.89 3.035 WALL TUBE DROP ) Fitting Size TXX-TYY Piece Number Take - T08-T06 consult Lokring 0.43 T16 9061059 0.54 T16-T14 9061063 0.96 3.33 T12-T10 9061060 0.89 1.94 3.035 WALL TUBE DROP ) [PIPE] Take A Out.83 3.89 3. 6. Take Out.035 WALL TUBE DROP ) Fitting Size TXX Piece Number Take - T08 9060286 0.40 T14-T10 consult Lokring 0.85 1.85 3.94 3.89 0. B Take Out.43 T16-T12 9061062 0.98 0.51 T20 9060298 0.90 3.83 3.89 3. C T08 9060287 0.86 T32 9062104 0.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).83 1.98 0.90 0.94 0.70 T24 9060164 0.36 T14 consult Lokring 0.82 3.90 3.98 4.94 1. Take Out.90 3.08 A Out.96 0.54 T20 9060165 0.89 3. C SS40 & SS-3000-TEE-TXX-002 ( 3/8 OD SWAGELOK ® DROP*) * SWAGELOK is a registered trademark of SWAGELOK CO.96 4.43 T14-T12 9061061 0.94 4. A Take Out.89 0. All Rights Reserved.90 1.98 2.90 0.07 A Out.98 3.89 1.40 T16 9060979 0.83 0.85 3.96 1.lokring.86 T32-T20 consult Lokring 0. C SS40-TEE-PXX-001 ( 3/8 OD X 0.68 T24 9060299 0.08 T32-T24 9062106 0. Drop Tees T E C H N O L O G Y C OR P O R A T I ON SS40 & SS-3000-TEE-TXX-001 ( 3/8 OD X 0.29 T12 9061051 0.85 T32 9062103 0.08 Fitting Size PXX Piece Number P12 9062004 0.89 3. C SS40 & SS-3000-RTEE-TXX-TYY-001 ( 3/8 OD X 0.33 T12 9061057 0. 85 0.40 T14-T12 9061054 0. C T08 9061016 0.09 1.89 1.94 3.85 3. B Take Out.90 1.96 3. Page 7 of 12 .98 4.89 1.40 T16-T12 9061055 0.98 0.com Copyright 2003 Lokring Technology Corporation.96 0.51 T20-T16 9060391 0.89 0.07 * SWAGELOK is a registered trademark of SWAGELOK CO. C P16 9061695 1.98 0. A Take Out.lokring.10 SS40 & SS-3000-TEE-TXX-003 ( 1/2 OD X 0.90 0.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).83 1.89 3.33 T12 9061017 0.68 T24-T16 9061657 0.44 T16 9061019 0.85 0. A Take Out.94 * SWAGELOK is a registered trademark of SWAGELOK CO.07 T32-T24 9062105 0.26 T10 9061008 0.85 1.21 T10-T08 9060285 0.94 2. SS-3000-TEE-PXX-TYY-002 ( 3/8 OD SWAGELOK ® DROP*) [PIPE TO TUBE] Fitting Size PXXTYY Piece Number Take Out. A Take Out.94 0.90 1.89 0.51 T16-T14 9060980 0.36 T14-T10 consult Lokring 0.09 0. A Take Out.90 1. C T08-T06 9061658 0.90 0.83 3.72 T24 9061020 0. B Take Out.78 P20 9061696 1.96 0.83 0.40 T14 9061018 0.89 3.89 1.89 1. C P16-T16 9061697 1. Drop Tees TECHNOLOGY CORPORATION SS40 & SS-3000-RTEE-TXX-TYY-002 ® ( 3/8 OD SWAGELOK DROP*) Fitting Size TXX-TYY Piece Number Take Out. SS40-TEE-PXX-002 ( 3/8 OD SWAGELOK ® DROP*) [PIPE] Fitting Size PXX Piece Number Take Out.81 1.049 WALL TUBE DROP ) www. All Rights Reserved.96 2.29 T12-T10 9061053 0.94 1.31 1.78 Fitting Size TXX Piece Number Take Out.85 T32-T20 consult Lokring 0. 6.85 T24-T20 9060301 0.55 T20 9060397 0.90 3.88 T32 9062111 0. 89 0.36 T14 9061068 0.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).90 1.98 P24 9062510 1.32 Fitting Size TXX Piece Number Take Out.07 * CPI is a trademark of PARKER HANNIFIN CORPORATION.98 0. C T08 9061065 0.44 T16-T12 9061029 0.10 T32-T24 9062117 0.89 3.85 T32 9062112 0.82 3.98 0.68 T24 9061071 0. A Take Out.96 2.049 WALL TUBE DROP ) Fitting Size TXX-TYY Piece Number Take Out.98 0.96 0.96 0.34 4.83 1.96 4. www.94 1.90 3.89 1.89 3. Take Out.96 0.11 4.81 P20 9061465 1.94 0. All Rights Reserved.89 0.98 2.90 1. C T08-T06 consult Lokring 0.29 T12-T10 9061077 0. B Take Out.85 3. Page 8 of 12 .21 T10 9061066 0. A Take Out.90 1.85 0.89 3.85 T24-T20 9061082 0.07 T32-T24 9062115 0.96 0.85 0.90 0.94 3. 6.51 T16-T14 9061080 0.98 0.83 1.40 T14-T10 consult Lokring 0.07 SS40 & SS-3000-TEE-TXX-005 ( 3/8 OD CPI DROP*) * CPI is a trademark of PARKER HANNIFIN CORPORATION.31 3. B Take Out.90 0.44 T14-T12 9061028 0.89 0.95 3.10 P32 9061464 1.049 WALL TUBE DROP ) [PIPE] Fitting Size PXX Piece Number Take A Out.85 0.85 0.51 T20 9061070 0.83 0.88 T24-T20 9061032 0.94 0.55 T16-T14 9061030 0.90 0.82 1.26 T10-T08 9060368 0.83 3.89 1.89 1.85 1.90 3.40 T14-T12 9061078 0.40 T16-T12 9061079 0.96 1.36 T14-T10 consult Lokring 0. A Take Out.89 0.88 T32-T20 consult Lokring 0. SS40 & SS-3000-RTEE-TXX-TYY-005 ( 3/8 OD CPI DROP*) Fitting Size TXX-TYY Piece Number Take Out.89 1.29 T12 9061067 0.89 1. Drop Tees TECHNOLOGY CORPORATION SS40 & SS-3000-RTEE-TXX-TYY-003 ( 1/2 OD X 0.89 1.40 T16 9061069 0.83 0.com Copyright 2003 Lokring Technology Corporation.lokring.10 SS40-TEE-PXX-003 ( 1/2 OD X 0.94 4.21 T10-T08 9061076 0.72 T24-T16 consult Lokring 0.09 3. C P08 9061466 0.85 T32-T20 9062116 0.68 T24-T16 consult Lokring 0.90 0.94 2.94 1.51 T20-T16 9061081 0.85 1.52 P16 9062509 1.33 T12-T10 9061027 0. C T08-T06 consult Lokring 0.89 3.55 T20-T16 9061031 0. 31 1. Drop Tees TECHNOLOGY CORPORATION SS40-TEE-PXX-005 ( 3/8 OD CPI DROP*) [PIPE] Fitting Size PXX Piece Number Take - P16 9061750 1.09 1.com Copyright 2003 Lokring Technology Corporation.31 1.90 1.77 SS-3000-TEE-PXX-TYY-005 ( 3/8 OD CPI DROP*) [PIPE TO TUBE] www. B Take Out. C * CPI is a trademark of PARKER HANNIFIN CORPORATION.93 Fitting Size PXX-TYY Piece Number Take Out. B Take Out. Page 9 of 12 .09 0.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04). A Take Out.09 1.93 P24 9062140 1. 6. C P16-T16 9061889 1.77 P20 9062137 1. C P20-P16 9061890 1. All Rights Reserved.11 2. Take Out. ** P16 and P20 Sizes are available without an internal travel stop SS40-RTEE-PXX-PYY-005 ( 3/8 OD CPI DROP*) [REDUCER] [PIPE] Fitting Size PXX-PYY Piece Number Take Out.06 A Out. A Take Out.lokring. 94 0.com Copyright 2003 Lokring Technology Corporation.96 T32-T24 9062114 0. C T08 9061085 0.85 1. All Rights Reserved. A Take Out.89 1.04 T10 9061086 0.73 T32 9062107 0. 6.94 1.89 1.85 0.90 1. SS40-TEE-PXX-008 ( 1/2 OD CPI DROP*) [PIPE] Fitting Size PXX Piece Number Take Out.56 T24-T16 consult Lokring 0.89 1. Page 10 of 12 .90 1. SS40 & SS-3000-RTEE-TXX-TYY-008 ( 1/2 OD CPI DROP*) Fitting Size TXX-TYY Piece Number Take Out.22 T14 9061036 0.09 1.56 T24 9061038 0.14 T12 9061087 0.38 T20 9061090 0.89 1. A Take Out.85 1. SS40 & SS-3000-TEE-TXX-009 ( 1/2 OD SWAGELOK® DROP*) Fitting Size TXX Piece Number Take Out.73 T32-T20 consult Lokring 0.85 0.90 1.90 0.89 1.22 T14-T10 9061198 0.38 T20-T16 9061101 0. B Take Out.96 1. Drop Tees TECHNOLOGY CORPORATION SS40 & SS-3000-TEE-TXX-008 ( 1/2 OD CPI DROP*) Fitting Size TXX Piece Number Take Out. C P16 9062145 1. C T08 9061033 0. www.04 T10 9061034 0.89 1.98 0.04 T10-T08 9061096 0.73 T24-T20 9061102 0.94 1.89 1.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).98 0. A Take Out.96 * CPI is a trademark of PARKER HANNIFIN CORPORATION.26 T16 9061037 0.14 T12 9061035 0.89 0.90 1.38 T20 9060618 0.94 1.lokring.89 1.98 1.96 0.96 0.83 1.73 T32 9062113 0.26 T16-T12 9061099 0.85 1.96 1.66 * CPI is a trademark of PARKER HANNIFIN CORPORATION.22 T14 9061088 0.90 0.94 1.96 * CPI is a trademark of PARKER HANNIFIN CORPORATION.98 1. A Take Out.96 * SWAGELOK is a registered trademark of SWAGELOK CO. C T08-T06 consult Lokring 0.26 T14-T12 9061098 0.83 1.14 T12-T10 9061097 0.26 T16 9061089 0.83 0.96 1.56 T24 9061091 0.83 1.89 0.38 T16-T14 9061100 0.82 1. 96 * SWAGELOK is a registered trademark of SWAGELOK CO.38 T20-T16 9061048 0. C T08-T06 consult Lokring 0.38 T14 consult Lokring 0.43 T16 9061197 0.43 T14-T12 9061195 0.55 T20 consult Lokring 0.89 5.85 0.73 T24-T20 9061049 0.049 WALL TUBE DROP ) SS40 & SS-3000-RTEE-TXX-TYY-012 ( 3/4 OD X 0.43 T16-T12 9061194 0. A Take Out.83 0.83 1.89 1.29 T12-T10 9061196 0.83 5.26 T16-T12 9061046 0. A Take Out.55 T16-T14 9061193 0.56 T24-T16 consult Lokring 0.98 0.13 T32-T24 consult Lokring 0.96 T32-T24 consult Lokring 0. 6.73 T24 9060978 0.73 T32-T20 consult Lokring 0.90 5.90 0.89 5. B Take Out.98 6.94 1.90 1.04 T10-T08 9060381 0.96 Fitting Size TXX Piece Number Take Out. C P20 9061930 1.94 0. Drop Tees TECHNOLOGY CORPORATION SS40 & SS-3000-RTEE-TXX-TYY-009 ( 1/2 OD SWAGELOK® DROP*) Fitting Size TXX-TYY Piece Number Take Out.90 5.90 1.89 5.90 T24-T20 9062393 0.89 5.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).85 0.82 1.94 0.98 0.22 T14-T10 consult Lokring 0.90 0.89 0.89 5.049 WALL TUBE DROP ) www.83 P24 9061751 1.94 1.94 5.94 5. A Take Out. C T08-T06 consult Lokring 0.73 T24-T16 consult Lokring 0.96 0.85 0.96 0.13 Fitting Size TXX-TYY Piece Number Take Out.89 1.90 0.83 5.98 0.com Copyright 2003 Lokring Technology Corporation.11 1.85 5.13 SS40 & SS-3000-TEE-TXX-012 ( 3/4 OD X 0.82 5.89 1.38 T14-T10 consult Lokring 0.lokring.89 0.38 T16-T14 9061047 0.90 T32 consult Lokring 0.96 1.55 T20-T16 consult Lokring 0.17 T10-T08 consult Lokring 0.96 0.89 0.96 0. Page 11 of 12 .83 0.29 T12 consult Lokring 0.14 T12-T10 9061044 0.90 T32-T20 consult Lokring 0. A Take Out.98 0.96 5.17 T10 consult Lokring 0. All Rights Reserved.90 5. C T08 consult Lokring 0.85 0.89 0.89 1.85 5.85 1.96 6. B Take Out. SS40-TEE-PXX-009 ( 1/2 OD SWAGELOK® DROP*) [PIPE] Fitting Size PXX Piece Number Take Out.90 0.31 1.89 5.26 T14-T12 9061045 0.94 6. 09 2.98 2. 6.73 1/2-14 Fitting Size PXX Piece Number Take Out. A Take Out. All Rights Reserved.61 1-11. Drop Tees TECHNOLOGY CORPORATION SS40-TEE-PXX-013 1/ NPT DROP [PIPE] Fitting Size PXX Piece Number Take Out.com Copyright 2003 Lokring Technology Corporation. C Thread P24 9062293 1.lokring. Page 12 of 12 .72 P16 9061912 1.76 2.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04).88 Fitting Size TXX-YY FPT Piece Number Take Out.5 SS40-TEE-PXX-026 ( 12mm OD X 1mm WALL TUBE DROP ) [PIPE] SS-3000-TEE-TXX-YY FPT *Threaded end conforms to female NPT thread www. C P12 9061911 0.11 2. A Take Out. B Thread NPT T20-1" 9061780 1. A Take Out. Other Individual Tool Kit and Multiple Tool Kit options are available. All rights reserved 7.lokring. lightweight case.: (905) 639-4050 FAX: (905) 639-6163 __________________________________________________________________www. consult your LOKRING representative or see the installation procedure for additional options www. 5-Step Installation Guide. 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL.com TECHNOLOGY CORPORATION Standard Tooling Selection for Carbon Steel MAS-3000 and Stainless Steel (CRES) SS40 Pipe Fittings Pipe Sizes Tool Kits Part Number 1/4" NPS (P04) Consult LOKRING Representative - 3/8" NPS (P06) Consult LOKRING Representative - 1/2" NPS (P08) MTK45-SS4/MAS-P08/P12/P16-FR 9080177 3/4" NPS (P12) MTK45-SS4/MAS-P08/P12/P16-FR 9080177 1" NPS (P16) MTK45-SS4/MAS-P08/P12/P16-FR 9080177 1" NPS (P16) MTK60-MAS/SS4-P16/P24/P32-FR 9080135 1 1/4" NPS (P20) Consult LOKRING Representative - 1 1/2" NPS (P24) MTK60-MAS/SS4-P16/P24/P32-FR 9080135 2" NPS (P32) MTK60-MAS/SS4-P16/P24/P32-FR 9080135 3" NPS (P48) ITK-100-MAS/SS4-P48 9080196 Notes : Each Multiple Tool Kit (MTK) consists of one LOKTOOL head. and indelible marking pen in a rugged.com Copyright 2003 Lokring Technology Corporation.lokring. multipurpose gage for each size and material (SS and CS).01 Standard Tooling Selection for MAS and SS Pipe Fittings (03-17-03) . inserts for each size. Each Multiple Tool Kit (MTK) consists of one tool head. 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL. one multipurpose gauge for each size listed. and indelible marking pen in a rugged. consult your LOKRING representative or see the installation procedure for additional options www.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________www. All rights reserved 7. and indelible marking pen in a rugged.04 Standard Tooling Selection for Tube Fittings (03-17-03) .com Copyright 2003 Lokring Technology Corporation. lightweight case. 5-Step Installation Guide.lokring. Other Individual Tool Kit and Multiple Tool Kit options are available.com TECHNOLOGY CORPORATION Standard Tooling Selection for Stainless Steel SS40 and SS-3300 and 70/30 Copper Nickel CN-3300 Tube Fittings Tube Sizes Individual Tool Kits Part Number Multiple Tool Kits Part Number 1/4" (T04) ITK10-SS4-T04 ITK04 9080199 9080212 Consult LOKRING Representative - 3/8" (T06) ITK10-SS4-T06 MTK20-SS4-T06/T08 9080223 1/2" (T08) ITK10-SS4-T08 9080081 MTK20-SS4-T06/T08 9080223 5/8" (T10) ITK20-SS4-T10 9080214 MTK20-SS4-T08/T10 9080219 3/4" (T12) ITK20-SS4-T12 9080079 MTK20-SS3-T12/T14/T16 9080085 7/8" (T14) ITK20-SS3-T14 9080078 MTK20-SS3-T12/T14/T16 9080085 1" (T16) ITK20-SS3-T16 9080077 MTK20-SS3-T12/T14/T16 9080085 1-1/4" (T20) ITK45-SS3-T20 MTK45-SS3-T20/T24 9080206 1-1/2" (T 24) ITK45-SS3-T24 MTK45-SS3-T20/T24 9080206 2" (T32) ITK60-SS4-T32 Consult LOKRING Representative - Notes : Each Individual Tool Kit (ITK) consists of one set of inserts installed in LOKTOOL head. one multipurpose gauge.lokring. 5-Step Installation Guide. a set of inserts for each size listed. lightweight case. All rights reserved 7. 960 GATEWAY DRIVE • BURLINGTON ONTARIO • CANADA L7L 5K7 TEL.lokring.com Copyright 2003 Lokring Technology Corporation.06 Hydraulic Power Supplies (04-23-03) .lokring.com T E C H N O L O G Y C OR P OR A T I ON Hydraulic Power Supplies Pumps and Hoses Description Actuated Part Number PUMP-OTC-QTRHRSE-ELEC* Electric Pump Foot Pedal 9080182 Pneumatic Pump Foot Pedal 9080139 Manual Pump Manual 9080036 15 foot Hydraulic Hose Assembly - 9080111 PUMP-TURBO-AIR-QD PUMP-P-19-QD HH15-QD Part Number Pump and Hose Kits HPS-TURBO AIR Air/Hydraulic Pump and Hose in Case 9080189 HPS-ELEC-OTC-QTRHRSE* Electric/Hydraulic Pump and Hose 9080184 HPS-MAN Manuel Pump and Hose 9080050 *Electric pumps are also available in 220 V www.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________________www.