D811390 ver.04 30-10-04 I QUADRO COMANDO GB CONTROL PANEL F D E P CENTRALE DE COMMANDE SELBSTÜBERWACHENDE STEUERUNG CUADRO DE MANDOS QUADRO DE COMANDO 8 027908 217875 LIBRA-MA-R 8 8 8 8 ISTRUZIONI D'USO E DI INSTALLAZIONE INSTALLATION AND USER'S MANUAL INSTRUCTIONS D'UTILISATION ET D'INSTALLATION INSTALLATIONS-UND GEBRAUCHSANLEITUNG INSTRUCCIONES DE USO Y DE INSTALACION INSTRUÇÕES DE USO E DE INSTALAÇÃO Via Lago di Vico, 44 36015 Schio (VI) Tel.naz. 0445 696511 Tel.int. +39 0445 696533 Fax 0445 696522 Internet: www.bft.it E-mail: [email protected] Ver.LIBRA-MA-R .2 . 04 D811390_04 . ........ > 2MOhm 500Vdc Working temperature: .. or use which is different from that expected and specified in the present documentation......Incorporated rolling-code radio receiver with transmitter cloning The board is provided with a terminal board which can be pulled out for easier maintenance or replacement.. polystyrene etc) according to the provisions set out by current standards............. For example.... We declare that it is in conformity with the following European Directives: 89/336/EEC.......... 24Va. conveying and shearing.. ....2Ah) Flat battery protection threshold: ..c. JP1 1-2 JP9 3-4-5 Thank you for buying this product. • Scrap packing materials (plastic....c........... Wires powered at different voltages must be physically separated................LIBRA-MA-R ......... ± 10% (1=L) (2=N) 6-7-8 9-10 Connection to motor 2: 3 motor + (red) 4 motor . gates etc.............c........ but if it is on the inside (or outside but placed in a plastic cable cannel) it has to be or at least egual to H05VV-F with section 3x1...... check for correct connection of the safety devices....... The wires must be clamped by an extra fastener near the terminals.... • The Company declines all responsibility for any consequences resulting from improper use of the product.03A threshold is fitted just before the power supply mains.. animals or things............ installation....... installation.. or suitably insulated with at least 1 mm extra insulation........... 98/37/EEC and subsequent amendments............. 3... -10 to +55°C Dielectric strength:….... As for all non-EEC countries... • Disconnect the electrical power supply before carrying out any work on the installation. • Keep the instructions together with the technical brochure for future reference........ • Do not modify the automation components...5 mm...... the outputs to terminals 11-12 (24 Va.O........ 2) GENERAL OUTLINE The LIBRA-MA-R control panel is supplied by the manufacturer with standard setting...... Keep nylon or polystyrene bags out of children’s reach...................... • Only use original parts for any maintenance or repair operation............. Any other use not specified in this documentation could damage the product and be dangerous......... The jumpers relate to the following terminals: 15-17 and 15-18............... • Do not allow persons or children to remain in the automation operation area... gates etc........6) and check the wiring.c...... operation and maintenance............c......... The board is supplied with a series of pre-wired jumpers to facilitate the installer’s work..c.. it has to be at least equal to H07RN-F..4Vd....... 1) GENERAL SAFETY WARNING! An incorrect installation or improper use of the product can cause damage to persons............. cardboard. check the devices connected for regular operation (paragraph 5........ • Instruct the product user about the control systems provided and the manual opening operation in case of emergency...... 12/14 hrs NOTE: In case of operation with battery back up......... • The installation must comply with the provisions set out by the following European Directives: 89/336/CEE............. is not allowed. 40W (24Vd.........../1A max) Blinker: .............. 20.. • Check that earthing is carried out correctly: connect all metal parts for closure (doors..... • Check that a differential switch with a 0. WARNING! For connection to the mains.....c....................... remove their respective jumpers........... 10A Maximum motor power: .. if the cable is out side (in the open)..... All the connection cables must be kept at an adequate distance from the dissipator.......). WARNING! Installation must be carried out using the safety devices and controls prescribed by the EN 12978 Standard.. • The construction components of this product must comply with the following European Directives: 89/336/CEE.........5A max Motor relay commutation current: ...... • Position at least one luminous signal indication device (blinker) where it can be easily seen........5A+3... refer to the current standards as well as principles of good technical practice. 73/23/EEC.....2Vdc Charging current: ....... Battery charging time: ..... 5 limit-switch control (white) Connection to motor 1: 6 motor + (red) 7 motor ......... see figure 1 Fuses: ...........3) WARNING – During the wiring and installation operations............... • The user must avoid any attempt to carry out work or repair on the automation system...... • The “Warnings” leaflet and “Instruction booklet” supplied with this product should be read carefully as they provide important information about safety.. see figure 2 (* other voltages available on request) BATTERY KIT BT BAT (Fig...5mm2 cross section and complying with the previously mentioned regulations......(black).c.................... • This product was exclusively designed and manufactured for the use specified in the present documentation.. 98/37/EEC and subsequent amendments................ ± 10% 50Hz* Mains/low voltage insulation: .............ENGLISH INSTALLATION MANUAL supports the EELINK protocol... • Fit all the safety devices (photocells. as well as from any deformation which might occur during use.....Limit-switch control inputs .. contact (24Va... • Anything which is not expressly provided for in the present instructions. and always request the assistance of qualified personnel..............) Supply to accessories: .. Its main characteristics are: ...........5mm2............. 130mA Outside temperature when values were measured: .... 4) TERMINAL BOARD CONNECTIONS (Fig....... ........ CHECK The LIBRA MA-R panel carries out a control (check) on the starting relays and safety devices (photocells....c.... for example by bands... mains/low voltage 3750Vac per 1 minute Motor output current: ... 27..... This product complies with recognised technical standards and safety regulations.. and fix a Warning sign to the structure............. in order to avoid unintentional automation activation...... • Keep radio control or other control devices out of children’s reach. if fitted... safety edge etc........ 73/23/EEC...c........ (180mA max absorption) 24Va.................. 24Va.. In case of malfunction................... 73/23/EEC...... N.............................230Va............. • The Company declines all responsibility for any consequences resulting from failure to observe Good Technical Practice when constructing closing structures (door........... 25°C Battery capacity: ... This product is supplied with an “Instruction Manual” which should be read carefully as it provides important information about safety..Separate inputs for safety devices .. 98/37/EEC and subsequent amendments........ • The Company declines all responsibility with respect to the automation safety and correct operation when other manufacturers’ components are used. having a contact opening distance equal to or greater than 3...) and 13-14 ( Vsafe 24 Va... our company is sure that you will be more than satisfied with its performance............. 6..... 20W max) D811390_04 ........ 04 Single-phase mains power supply 230Va.....................(black) 8 limit-switch control (white) Connection to blinker (24Va..................c. • Installation must be carried out using the safety devices and controls prescribed by the EN 12978 Standard.. When installing the BT-BAT kit. 3) TECHNICAL DATA Power supply: ... • Do not install the product in explosive atmosphere......) before carrying out each opening and closing cycle........ Any alteration must be set by means of the incorporated display programmer or by means of UNIPRO..............c. unless explicitly authorised by the company.Ver... V safe (180mA max absorption) Gate-open warning light: ........... the abovementioned standards as well as the current national standards should be respected in order to achieve a good safety level........Control of two low-voltage motors up to 40W power .....) which are needed to protect the area from any danger caused by squashing..............................Electronic torque setting with obstacle detection .... 25W max Dimensions: .. • Fit an omnipolar or magnetothermal switch on the mains power supply.....) and all system components provided with an earth terminal............ use a multipolar cable with a minimum of 3x1......... The Control unit completely 12 ... Also disconnect any buffer batteries. If the abovementioned terminals are in use.................. 2x (12V 1...............) have a voltage of 24 Vd...... use and maintenance.. electric edges etc......... polarised as shown in Fig.6) Charging voltage: . ........ .. is obtained by timing one manoeuvre and setting a minimum value for this parameter. and therefore requires an appropriate supply unit.... The LIBRA-MA-R control unit does not supply the UNIPRO programmer with power...... contact (Fig. When a photocell is obscured on closing....... if the opening cycle has started (not from pedestrian function)...).............. START pushbutton (N...O. The writing appearing on the display is indicated between round brackets.. Note: The slow-down time.. carefully read the instructions relating to UNIPRO...).Photocells on opening (photc... refer to the “LOGIC” submenu.Number of manoeuvres carried out since the latest maintenance operation (the value is expressed in thousands. A and B and to the paragraph on “Configuration”....Number of memorised radio control devices.. 3a)...... the programming mode is entered.) .. 6......Control unit software version ....C.. ranging from 1 to 30 seconds..supply to photocells or other devices Output 24Va.. WARNING: Check that the impact force value measured at the points established by the EN 12445 standard is lower than that specified in the EN 12453 standard.. leave the bridge 15-18 connected.. stops and reopens OFF Enables 4-step logic.... 04 .... V safe 180mA max .... then scroll the display screenfuls using the up/down arrows to set the numerical values of the parameters listed below...... 180mA max ...... If not used... When the OK key is pressed during the initial presentation phase.. opens on opening: . Opening delay time (open delay time) [ 1s ] Set the opening delay time for motor 1 relative to motor 2..O..... . A Start impulse has the following effects: door closed: .. Closing delay time (cls delay time) [ 1s ] Set the closing delay time for motor 2 relative to motor 1...... contact (24Va.. refer to Fig... See paragraph 7 on “Serial connection”. ... Photocell input (N.................... If..... Here follows a list of the main menus and the respective submenus available............. and the “PARAMETERS” submenu.....Number of total manoeuvres carried out (the value is expressed in thousands.....Motor 1 torque (Mot1 torque) [ 50% ] (UNIPRO ⇒ Advanced parameters ⇒ address 3) Set the numerical value of the motor 1 torque between 1% and 99%.......... A Start impulse has the following effects: door closed: . suitable for standard installations. Motor 2 slow-down torque (m2 t slow) [ 45% ] (UNIPRO _ Advanced parameters _ address 9) Set the numerical value for slow-down torque of motor 2 between 1% and 99%. The modifications made are only set if the OK key is subsequently pressed............. The predefined parameters can be altered by means of either the incorporated display programmer or UNIPRO.. Refer to Figures A and B for the configuration procedure...................... therefore the display constantly shows 0000 during the first thousand manoeuvres) ........... closes on closing: ..............3 Steps (3 step) [ OFF ] ON Enables 3-step logic......1) PARAMETER MENU (PARAm) ........... stops and enters TCA (if configured) door open: .. ranging from 1 to 30 seconds....... for example........ ƽ ƽ 6. The programmer is provided with three pushbuttons for menu scrolling and function parameter configuration: + menu scrolling/value increment key menu scrolling/value reduction key OK Enter (confirm) key The simultaneous pressure of the + and ..... Enter the “CONTROL UNITS” menu. When the OK key is pressed for the first time...... .3a)..)../ 1A max)) or alternatively 2nd radio channel (see paragraph 6 on “Configuration”) Antenna input for radio-receiver plug-in board (23 signal–24 braid). Incorrect sensitivity setting can cause injuries to persons or animals..... - ENGLISH - JP7 21-22 - 23-24 - 5) PROGRAMMING The control panel provided with a microprocessor is supplied with function parameters preset by the manufacturer....)... the first menu can be accessed directly.... Motor 2 Normal Speed Time (m2 fast time) [ 5s ] (UNIPRO fi Advanced parameters fi address 7) Set the time to normal speed (not slowed down)... During the closing phase...... stops and enters TCA (if configured) door open: ....Rapid closing (fast cls) [ OFF ] ON Closes the gate after photocell disengagement.13 ...The predefined parameter is shown between square brackets [ 0 ].......... OFF The Start impulse becomes effective during the opening or closing phase... this excludes photocell operation on opening... OFF: In case of obscuring......O.. stops and does not enter TCA (stop) after stopping: . Slow-down speed (slov speed) [ 2 ] (UNIPRO ⇒ Advanced parameters ⇒ address 5) Set the slow-down speed by choosing from the following values: 0 – slow-down disabled 1 – slow-down to 50% of normal speed 2 – slow-down to 33% of normal speed 3 – slow-down to 25% of normal speed Zone (zone) [ 0 ] Set the zone number between a minimum value of 0 and a maximum value of 127....... In the case where programming is carried out by means of UNIPRO.........Motor 2 torque (Mot 2 torque) [ 50% ] (UNIPRO ⇒ Advanced parameters ⇒ address 4) - - - - Set the numerical value of the motor 2 torque between 1% and 99%. one manoeuvre lasts 25 seconds..........TCA (TCA) [ OFF ] ON Activates automatic closing OFF Excludes automatic closing .......Automatic Closing Time (TCA) [ 10s ] Set the numerical value of the automatic closing time from 3 to 60 seconds.... If not used. In the case where programming is carried out by means of the incorporated programmer... STOP pushbutton (N.... and then halts in the STOP status. Connect the UNIPRO programmer to the control unit through the UNIFLAT and UNIDA accessories (See fig......O.................. it immediately reverses the motion........ . open) [ OFF ] (UNIPRO ⇒ Advanced logics ⇒ address 14) ON: In case of obscuring. closes on closing: ...Ver.... on closing and on opening..).... leave the bridge 15-17 connected.............. the Ampere-stop function halts the leaf movement.... the pedestrian command has no effect.c.... therefore the display constantly shows 0000 during the first thousand manoeuvres) ................ before waiting for the end of the TCA set........ 6) CONFIGURATION The display programmer is used to set all the LIBRA-MA-R control panel functions......... OFF Command not entered. Output for gate-open warning light output (N.. NOTE: In case of obstacle detection........... Pedestrian pushbutton input (N.....keys is used to exit the active menu and move to the preceding menu..... Fault input (N.. For the function logics...... it reverses the motion only after the photocell is disengaged...Impulse lock (ibl open) [ OFF ] ON The Start impulse has no effect during the opening phase... opens on opening: ..c.... Activation is carried out by motor 2...O.. a setting of “normal speed time” to 20s will produce a slow-down time of 5s both on closing and on opening..... Motor 1 slow-down torque (m1 t slow) [ 45% ] (UNIPRO _ Advanced parameters _ address 8) Set the numerical value for slow-down torque of motor 1 between 1% and 99%.. between 1 and 10 seconds... and proceed in the following way... the photocells are active both on opening and on closing... between 1 and 10 seconds. The following pieces of information appear on the display at first: ..... opens ........D811390_04 INSTALLATION MANUAL JP8 11-12 13-14 15-16 15-17 15-18 15-19 15-20 Output 24Va.... Motor 1 Normal Speed Time (m1 fast time) [ 5s ] (UNIPRO fi Advanced parameters fi address 6) Set the time to normal speed (not slowed down)...Photocell test (test phot) [ OFF ] LIBRA-MA-R ...............C..c.2) LOGIC MENU (logic.. 4). reverses its motion for 1 sec. or damage to things........supply to photocell transmitters with checking function (Fig.. Input for photocells provided with checking N...... . Therefore the rod continues its travel for another 0.. 6. . a new autoset operation must be carried out.3) RADIO MENU (RADIO) .Motors in operation (1 mot ON) [ OFF ] ON Only motor 2 is in operation (terminals 3.open) [ OFF ] ON The input between the two terminals 15-16 acts as open OFF The input between the two terminals 15-16 acts as start 6. see paragraph on “Radio Transmitter Cloning”. the obstacle detection function is not active. Receiver code reading (RX code) This displays the code entered in the receiver (par.Add Allows you to add one key of a radio control device to the receiver memory. . (Fig. After restoring. T3 or T4) of a transmitter to be memorised. the display shows four digits separated by a dot.. during which the minimum torque value needed for leaf movement is automatically set. OFF The receiver is configured for operation in rolling-code mode. and represent the maximum torque reached by motor 1 (35) and motor 2 (40). Incorrect sensitivity setting can cause injuries to persons or animals. During this phase.ITALIAN (ITA) .Master/Slave (Master) [ OFF ] ON The control panel is set as Master in a centralised connection (see Paragraph 7). Add Start button (add start) associates the required key to Start command Add 2ch button (add 2ch) associates the required key to 2nd radio channel . it is important to avoid obscuring the photocells. Movement is exclusively halted by activation of the closing limit switches.Fixed code (fixed code) [ OFF ] (UNIPRO ⇒ Advanced logics ⇒ address 13) ON The receiver is configured for operation in fixed-code mode.5 sec. if autosetting has been successfully completed. and the control unit executes an opening manoeuvre followed by a closing manoeuvre. 4 and 5).ENGLISH (ENG) .FRENCH (FRA) . 6. Monitoring: During the opening and closing phases. . and correct limit-switch activation. autosetting must be carried out with the control panel supplied by mains power voltage.. . see paragraph on “Radio Transmitter Cloning”.4) LANGUAGE MENU (language) Allows you to set the language on the display programmer..Gate-open or 2nd radio channel warning light (SCA 2ch) [ OFF ] ON The output between terminals 21 and 22 is configured as Gate-open warning light. WARNING!! The autoset operation is only to be carried out after checking the exact leaf (opening/closing) movement.40. 2 – Within 10s press the hidden key (P1) and the normal key (T1. Consult paragraphs 8. WARNING!: Enabling the Hold-to-run logic entails a different use of the START and PEDESTRIAN buttons: START takes on the hold-to-run OPEN function PEDESTRIAN takes on the hold-to-run CLOSE function OFF Impulse operation. .5) DEFAULT MENU (default) Restores the preset default values on the control unit. OFF This disables transmitter storage via radio. STOP or PED commands and the display. and if necessary set a value about 15-20 percent points higher in the parameter menu. according to the 3 or 4 step logic. after detecting the closing limit switch or upon reaching the mechanical backstop. This function activates leaf pressure on the mechanical backstop. if stored it displays a message showing the receiver number in the memory location (from 01 to 64). 10 and 11 for further information concerning the advanced functions of the Clonix incorporated receiver. OFF The control panel is set as Slave in a centralised connection (see Paragraph 7). returns to the Autoset menu. T2. This mode does not require access to the control panel. enter the D811390_04 . the “. With this configuration. T2. ON Activates photocell check OFF Deactivates photocell check If this setting is not activated (OFF).Read (read) Checks one key of a receiver.Start-Open selection (start . . 11).. it is thus necessary to check the wear condition of the gate and the regular movement of the leaves before proceeding to a new autoset operation. T3 or T4). The receiver exits the programming mode after 10s. 7) STATISTICS Having connected the UNIPRO programmer to the control unit. it means that the autoset procedure has not been successfully completed.ENGLISH INSTALLATION MANUAL from the receiver memory. at the same time the display shows the “AMP” message. If the maximum torque value reached during the manoeuvre gets sensibly close to the value set in the parameter menu.Eliminate list (erease 64) WARNING! Completely removes all memorised radio control devices 14 . 04 ƽ ƽ WARNING: Check that the impact force value measured at the points established by the EN 12445 standard is lower than that specified in the EN 12453 standard. malfunctions may occur in the future following wear or slight door deformation. It is therefore advisable to check the maximum torque reached during some of the manoeuvres carried out in the course of installation. 5) ON To be used when the mechanical closing backstop is fitted. The transmitters can only be memorised using the appropriate Radio menu. After this. Diagnostics: In the case of malfunctions. and the key number (T1.SPANISH (ESP) 6. both during normal operation and in the case of malfunctions.7) AUTOSET MENU (autoset) Allows you to automatically set the Motor torque.Lock hold (block persist) [ OFF ] (Fig.” message is displayed. the display shows a message indicating which device needs to be checked: STRT = START input activation STOP= STOP input activation PHOT= PHOT input activation FLT = FAULT input activation for checked photocells In the case where an obstacle is found. as well as using the START.LIBRA-MA-R . . WARNING! During the autoset phase.GERMAN (DEU) .Hold-to-run control (hold-to-run) [ OFF ] ON Hold-to-run operation: the manoeuvre continues as long as the control key is kept pressed. 6. after pressing any key. In the case where buffer batteries are used. T3 or T4) of a transmitter already memorised in standard mode by means of the radio menu.Radio transmitter programming (radio prog) [ ON ] (UNIPRO ⇒ Advanced logics ⇒ address 15) ON This enables transmitter storage via radio: 1 – First press the hidden key (P1) and then the normal key (T1. OFF Both motors are in operation. These values allow the torque setting to be corrected.6) DIAGNOSTICS AND MONITORING The display on the LIBRA-MA-R panel shows some useful information. other new transmitters can be entered before the end of this time. the pedestrian input is disabled. 9. The digits are constantly updated during the manoeuvre. therefore the installer must control the automation movement and prevent persons and things from approaching or standing within the automation working range. 5b) .Ver. . or damage to things. on the other hand. in this case the 2nd radio channel controls pedestrian opening. the LIBRA-MA-R panel stops the door and activates a reverse manoeuvre. the control unit displays the “OK” message and. without this being considered as an obstacle by the Ampere-stop sensor. . So by activating the closing limit switches slightly earlier. the control unit displays the “KO” message. If.. it inhibits the photocell checking function. 5a) OFF To be used when no mechanical closing backstop is fitted. OFF The output between terminals 21 and 22 is configured as 2nd radio channel. in this case proceed to carrying out precise setting of the closing limit-switch activation. the leaves will come to a perfect halt against the backstop. allowing connection of devices not provided with additional checking contact. T2. (Fig. for example 35. As soon as the OK pushbutton is pressed. after storage it displays a message showing the receiver number in the memory location (from 01 to 64). . these should be sorted out by type (electrical components. controls the excitation of the 2nd radio channel relay for 1s.Number of cycles carried out. If you wish the transmitter to activate output 2 (2nd radio channel relay) by means of key1. B1). the first transmitter assigns the key code to the receiver. In this second case. each of the LIBRA-MA-R control panels must be appropriately configured. . PROGRAMMING Transmitter storage can be carried out in manual mode or by means of the UNIRADIO programmer which allows the complete installation database to be managed through the Eedbase software. The zone number allows you to create groups of automation units. they must be replaced. It is automatically set to zero after each self-diagnosis or parameter writing. key2. To be updated manually from the appropriate menu “Update maintenance date”. while leaving the essential product features unchanged. The presence of metallic masses next to the antenna can interfere with radio reception. count the number of manoeuvres carried out up to that time. which will have control over all the others. . it is indispensable to use wires from the same pair. 11. receiver programming takes place through the connection of UNIRADIO to the LIBRA-MA-R control panel. proceed as follows: • Disconnect the power supply and the entire electrical installation. exclusively using a telephone-type line. making reference to fig. LIBRA-MA-R . For transmitters without hidden key. 10) MANUAL PROGRAMMING In the case of standard installations where advanced functions are not required. 16 characters can be entered for installation identification. at any time and without undertaking to update the present publication. Cloning by replacement is used to create a new transmitter which takes the place of the one previously memorised in the receiver. B2). 14) DISMANTLING Warning: This operation should only be carried out by qualified personnel. key”.6) The LIBRA-MA-R control panel allows several automation units (SCS) to be connected in a centralised way by means of appropriate serial inputs and outputs. after opening the battery compartment. The descriptions and illustrations contained in the present manual are not binding. controls a START command. At this point. 11) RADIO-TRANSMITTER CLONING Rolling-code cloning / Fixed-code cloning Make reference to the UNIRADIO Instructions and the CLONIX Programming Guide. 04 . When the control unit is disassembled to be reassembled on another site.Board microprocessor software version.6. B for basic programming. plastic etc. proceed to connecting all the LIBRA-MA-R control panels. • In the case where some of the components cannot be removed or are damaged.Date of latest maintenance operation. Each zone can only be assigned one Master unit. aluminium. key3 or key4. use RG8 coaxial cable. 12) SERIAL CONNECTION USING SCS BOARD (Fig.output channel 1. copper. the Master unit in zone 0 also controls the Slave units in the other zones.). move the antenna to a more suitable position. in this way a specific transmitter can be removed from the memory and will no longer be usable. For Antenna-Receiver connection. as in fig. key3 or key4.D811390_04 INSTALLATION MANUAL CONTROL UNIT / STATISTICS menu and scroll the screenful showing the statistical parameters: . Following the diagram in Fig. Therefore it will be possible to remotely program a large number of additional transmitters or. In case of scrapping. B. ENGLISH In the case of manual programming. 4. the automation devices do not entail any particular risks or danger. if activated. . using the UNIFLAT and UNIDA accessories as indicated in Fig.Ver. B. although abandoning the variable code. Should a telephone cable with more than one pair be needed.output channel 2. When coding safety is not a decisive factor. Note: Hidden key P1 appears differently depending on the transmitter model. by setting a MASTER unit first of all. if activated. . Also set the Zone number (see parameter menu) between 0 and 127. enter the transmitter in menu “2nd ch. The length of the telephone cable between one appliance and the next must not exceed 250 m. enter the transmitter in menu “Start key”. 8) INTEGRATED RECEIVER TECHNICAL SPECIFICATION Receiver output channels: . provides a high number of coding combinations. the on-board receiver allows you to carry out fixed-code additional cloning which. this code is necessary in order to carry out subsequent cloning of the radio transmitters. manufacturing and commercial improvement of the product. For transmitters with hidden key. for example. Materials must be disposed of in conformity with the current regulations. If you wish the transmitter to activate output 1 (START) by means of key1. 9) RECEIVER CONFIGURATION The on-board receiver combines characteristics of utmost safety in copying variable code (rolling code) coding with the convenience of carrying out transmitter “cloning” operations thanks to an exclusive system. bridging the two P1 points by means of a screwdriver (fig. This makes it possible to use one single command to open and close all the automation units connected. as in fig.1) ADVANCED PROGRAMMING: COLLECTIVE RECEIVERS Make reference to the UNIRADIO Instructions and the CLONIX Programming Guide. each one answering to the Zone Master unit.Number of cycles carried out from the latest maintenance operation. In case of insufficient transmitter range. either as an addition or as a replacement of a particular transmitter. you can proceed to manual storage of the transmitters. If motors are replaced. Cloning a transmitter means creating a transmitter which can be automatically included within the list of the transmitters memorised in the receiver. In case of materials to be recycled. Transmitter versions which can be used: all Rolling Code transmitters compatible with ANTENNA INSTALLATION Use an antenna tuned to 433MHz. the key P1 function corresponds to simultaneously pressing the 4 transmitter keys or. to be necessarily set as SLAVE (see logic menu). press hidden key P1 (fig. The Company reserves the right to make any alterations deemed appropriate for the technical.Installation description. replacement transmitters for those which have been lost. therefore keeping it possible to “copy” any transmitter which has already been programmed . 13) SCRAPPING Warning: This operation should only be carried out by qualified personnel.15 . key2. - IMPORTANT NOTE: ATTACH THE ADH ESIVE KEY LABEL TO THE FIRST MEMORISED TRANSMITTER (MASTER). without making changes directly to the receiver. min 10=1s.+ OK [0050] OK PRG m2 t .+ OK [off] ON OFF OK PRG TEST PHOT .+ OK [off] ON OFF OK PRG . programming is exited and the display switched off.+ OK [0002] OK PRG +/LOGIC. B BLOC persist . max 99%) +/END 3 step .+ OK [0050] OK PRG slov speed m2 fast time . total manoeuvres (in thousands) No. A LEGENDA ACCESS TO MENUS Press the OK key + +/- OK 8888 OK [ 00 ] OK Simultaneously press the + and . manoeuvres since latest maintenance(in thousands) No.+ OK [on] [off] ON OFF ON OFF Slow-down speed 0= Slow-down disabled 1= 50% of normal speed 2= 33% of normal speed 3= 25% of normal speed Zone numerical value (default 0.+ OK OK start open OK [off] ON OFF OK PRG 16 .+ TCA .+ +/PARAM OK OK [0010] OK PRG +/END m1 t . OK zone OK [0000] ON OFF OK PRG TCA . max 60=60s) Motor 1 torque value expressed in % (default 50%. min 0. 04 D811390_04 .+ m2 t slow .+ OK 0002] [0050 OK PRG slov speed . min 1%.Fig. radio control devices memorised /ON /OFF PRG Message: Programming in progress Message: KO! (value or function error) Message: “Wait” (enter value or function) OK . max 127) OK PRG PRG master . Simultaneous pressure of the + and – keys allows you to exit the active menu and return to the preceding menu.+ OK [off] ON OFF OK PRG Opening phase-difference Time value expressed in tenths of a second (default 10=1s.+ OK [0045] OK PRG .+ OK [off] ON OFF OK PRG hold-to-run .= following) BFT LIBRA1.+ OK [0050] OK PRG m1 t slow . The modifications made are only confirmed if the OK key is subsequently pressed. min 1=1s.Ver. min 3=3s.0 0000 0000 00 Control unit software version No. min 1%.+ OK [0010] OK PRG m1 fast time . max 99%) Motor 2 torque slow-down value expressed in % (default 45%.+ OK [off] ON OFF OK PRG radio prog .+ OK [oFF] OK PRG PARAMETER MENU TCA (automatic closing time) value expressed in seconds (default 10=10s. Preset value Parameter increment/reduction or ON/OFF commutation Press OK key (Enter/confirm) Menu scrolling (+ = preceding .+ OK [off] ON OFF OK PRG FOLLOWING MENUS FIG.+ OK [off] ON OFF OK PRG fixed code . max 99%) Motor 1 torque slow-down value expressed in % (default 45%. max 10=10s) Motor 1 slow-down speed time value expressed in seconds (default 5=5s.LIBRA-MA-R . min 10=1s. min 1%.+ photoc. open .+ OK [off] ON OFF OK PRG ibl open . if this takes place at the main menu level. max 30=30s) Motor 2 slow-down speed time value expressed in seconds (default 5=5s.+ OK [0045] [0010] OK PRG open delay time .+ OK [off] ON OFF OK PRG SCA 2ch . max 99%) Motor 2 torque value expressed in % (default 50%.+ OK OK PRG cls delay time . max 30=30s) i Mot ON . min 1%. max 100=10s) Closing phase-difference Time value expressed in tenths of a second (default 10=1s. min 1=1s.keys.+ OK [off] ON OFF OK PRG fast cls . B3 - + desired button 01 t1 READ + OK Press the required T (key) on radio control device Ð see Fig. A P 1 T3 T1 T3 T4 T2 T4 - + + OK / RADIO + - ADD start + OK hidden button 01 Press P1 (pushbutton) on radio control device. + - / COD RX OK 1A9C OK 22FD OK 01 OK language + - OK ITA + OK RADIO MENU ADD . after storage it displays / FRA OK a message showing the receiver number in the memory location (from 01 to 64).Ver. B3 / desired button Release P1 on radio control device ADD 2ch OK hidden button 01 Press P1 (pushbutton) on radio control device. B3 + ERASE 64 + OK PRG. B 1 P1 P1 2 T1 T2 T1 T2 3 T1 T2 PRECEDING MENUS FIG. AUTOset + - OK .D811390_04 Fig. - esp + OK COD RX Displays the receiver code. 04 . release END Press the required T (key) on radio control device Ð see Fig.Checks one key on a receiver. . END - + - + Add Start button Start command OK Ð associates the required key to DEU + Add 2ch button Ð associates the required key to 2nd radio channel READ .17 . . release Release P1 on radio control device Press the required T (key) on radio control device Ð see Fig. Make reference to paragraph 11. OK / WARNING! During the autoset phase.A l l o w s y o u t o a d d o n e k e y o f a r a d i o c o n t r o l device to the receiver memory. therefore the installer must control the automation movement and prevent persons and things from approaching or standing END within the automation working range. . . END OK AUTOSET MENU It automatically sets the motor torque. LIBRA-MA-R . T2. . the obstacle detection function is not active. T3 or T4). and the key number (T1. DEFAULT + - OK PRG OK ENG + OK / ERASE 64 WARNING! Completely removes all memorised radio control devices from the receiver memory. if stored it displays a message showing the receiver number in the memory location (from 01 to 64). Fig.Ver. 3 JP1 1 2 JP9 3 4 5 FC 6 7 8 FC 9 10 11 12 13 14 M2 M1 L N 25W max.LIBRA-MA-R . 1 Fig. 2 10 F 1A25T 8888 F 2AT (110V) F 1AT (230V) 236 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 8888 SD OK Fig. 3a SCA JP8 11 12 24V ~ JP8 17 18 PHOT 13 14 24V ~VSafe 15 COM 16 19 FAULT 20 11 12 24V ~ 13 14 24V ~VSafe 15 COM 16 17 18 PHOT 19 FAULT 20 11 12 24 V~ 21 22 II¡ CH 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 19 20 21 22 Rx 1 1 Tx 1 2 Rx 1 1 Tx 1 2 Rx 2 1 Tx 2 2 42 . + + 24V ~ 24V ~ VSafe JP8 15 COM JP7 16 START JP16 22 23 ANT 17 STOP 18 PHOT 19 FAULT 20 PED 21 24 SHIELD SCA / II¡CH. 04 23 24 1 94 0 D811390_04 .Fig.R NO NO NO NC NC ANT. 43 . 18 4 LINX UNIFLAT UNIPRO/UNIRADIO 88 88 UNIPOWER UNIDA UNIFLAT Contatti Contacts Contacts Kontakte Contactos Contatos UNIFLAT Contatti Contacts Contacts Kontakte Contactos Contatos UNITRC UNIFLAT UNIMITTO UNITRC Contatti Contacts Contacts Kontakte Contactos Contatos T1 Led T2 P1 P1 T1 2 T 3 T 4 T P1 P1 P1 P1 UNIMITTO UNITRC P1 Contatti Contacts Contacts Kontakte Contactos Contatos 1 2 1 2 3 4 3 4 LIBRA-MA-R . 04 .D811390_04 Fig.Ver. 0445 696511 Tel. RX1 RX2 TX1 TX2 AUTOMATISMES BFT FRANCE 13 Bld E. 14. 6 JP4 JP5 LIBRA MA-R 88 88 JP11 SCS SBS 33 33 230V (*) 44 25V 55 33 (*) 110V LIBRA MA-R JP8 11 12 13 14 15 16 17 18 19 20 COM START STOP FAULT PHOT PED 8888 23 24 erm el ho 12V.2 AH 55 44 33 -++ ITALIA D811390_04 ++ -- .a. 1. +39 0445 696533 Fax 0445 696522 Internet: www. Fax BFT (0033) 04 78 76 09 88 (0033) 04 78 76 92 23 DEUTSCHLAND BFT Torantriebssysteme GmbH Johannisstr.2 AH ouge-Rot-Rojo V 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 R edo-R ss NO NO NO NC NC + - + - 24V= 24V= VSafe SCS1 SCS2 SCS3 RX1 RX2 TX1 TX2 RX1 RX2 TX1 TX2 Max.de Tel.bft-torantriebe.bft.naz.D-90763 Fürth http://www.it Ro SBS JP1 6 5 4 3 2 1 12V. 04 0049 911 773323 0049 911 773324 Via Lago di Vico. 250m BFT FRANCE BFT S. Fax 44 . 69008 Lyon e-mail: [email protected] A B Fig.it E-mail: [email protected] Tel. 44 36015 Schio (VI) Tel. 1.p. Michelet.LIBRA-MA-R .Ver. 5 0.