Kidarooz 535 Owner’s ManualThank you very much for purchasing a well engineered, high quality Kidarooz product! We are sure it will bring your family years of enjoyment outdoors. Please keep this Owner’s Manual for future reference. If you sell or give this product to someone else, please include this Owner’s Manual, and ask the new owner’s to read the owner’s manual completely before operating. • • • PRIOR TO ASSEMBLY Please read this Owner’s Manual completely before assembling or operating this product. An adult should carry out assembly of this product. If any parts are missing or damaged, do not return this carrier to the store. Contact our customer service department at
[email protected] or 1-866-543-2766. IMPORTANT SAFETY INFORMATION WARNING Failure to follow these warnings and assembly instructions could result in serious injury or death! WARNING Immediately discard all plastic bags and plastic wrapping materials! WARNING Maximum weight capacity is 100 lb / 45 Kg including passengers and cargo! Do not use with children who exceed the maximum weight limitations! WARNING When a single child is being transported, seat him/her in the center! WARNING Never use this trailer/stroller if it becomes damaged! WARNING Passengers must always use seat belts and wear a CPSC or CE approved helmet! WARNING Never allow children to assemble, fold, or disassemble this unit! WARNING Never leave children unattended in or around this product! WARNING Accessories or parcels placed in the trailer/stroller may cause it to become unstable! WARNING Children must be at least 1 year old, and able to sit upright unassisted! WARNING Before using, be sure the product is correctly assembled according to the manufacturer’s instructions! WARNING Periodically re-check all fasteners to make sure they are tight! WARNING Do not use cleaning solvents! Clean only with mild soap and water! WARNING To prevent injury, please use extreme care when folding and unfolding this product! WARNING Do not install a car seat or any other seating device not approved by the manufacturer inside the trailer! WARNING Make no modifications to the trailer! SAFE TRAILERING TIPS WARNING Ride with extreme caution! Never exceed 10 mph, and slow down to less than 3 mph around corners and on rough roads! WARNING Have your bicycle safety inspected before attaching the trailer! WARNING Inflate tires to within the range shown on the tires’ sidewall! Check tire pressure before each use! WARNING Use a foot pump of hand pump to inflate tires! Pressurized air hoses can cause over inflation! WARNING Use of trailer changes the stability, braking requirements, and riding characteristics of your bike! WARNING Make sure your bike brakes work properly! Braking distance is increased when pulling a trailer! WARNING This trailer is wide! Allow extra clearance near curbs, signs, parked cars, and other obstacles! WARNING Do not allow the children’s body, clothing, shoe laces, or toys to come in contact with moving parts! WARNING Always use the safety flag for increased visibility! WARNING Never ride a bicycle/trailer at night without adequate lighting! WARNING Obey all local legal requirements! especially going downhill! You could loose control! TRAILER AND STROLLER MODES Trailer Mode Stroller Mode . pedaling. or steering of the bicycle! WARNING A reflector that complies with CPSC regulations shall be visible on the rear of the trailer! WARNING Install a rearview mirror on your bike to check on children in the trailer! WARNING Use extreme caution when turning on uneven pavement. as it was not designed for this use! WARNING Never climb or descend stairs with the stroller! WARNING Use extreme caution on hills. ensure the attached trailer does not interfere with braking.WARNING Before each ride. or by extended periods in warmer temperatures without adequate ventilation and hydration! SAFE STROLLING TIPS WARNING Always use the safety wrist strap when pushing children in the stroller mode! Failure to do so could result in your losing the stroller! WARNING Always engage both parking brakes whenever stopped! Failure to do so could result in the stroller rolling away! WARNING Never in-line skate with this stroller. and going downhill! Avoid steep hills as you could lose control of the trailer! WARNING Never remove protective canopy when pulling children in the trailer! WARNING Do not ride over curbs! Avoid bumps and holes! Always signal your turns! WARNING Be aware of exposure hazards such as wind chill and heat exhaustion by less-active trailer passengers in prolonged exposure in colder temperature. which are both supplied. STEP 1 1 Remove the trailer from the carton and compare the contents with the parts list Remove all contents from inside the carton and place them on a clean flat surface. do not return this carrier to the store.PARTS LIST Quantity 1 2 1 1 1 Description Frame including seat and weather cover 20” rear wheels Front stroller wheel Handlebar Plastic bag containing the following: Owner’s Manual Nuts Bolts Plastic Washers Allen Key Open end Wrench Quantity 1 1 1 1 1 2 2 2 1 1 Description Safety wrist strap High visibility flag Front Bumper Trailer arm TOOLS REQUIRED FOR ASSEMBLY Only a 4mm Allen key and an 11 mm open end wrench. ASSEMBLY AND OPERATING INSTRUCTIONS Note: Any reference to orientation (left or right) is from the passenger’s point of view while in the trailer. WARNING Immediately discard all plastic bags and plastic wrapping materials! . Compare them with the parts list above to make sure that no parts are missing. are required to assemble the bumper onto the trailer. If any parts are missing or damaged. Lift open the frame and remove all of the unattached parts from inside the trailer. Contact our customer service department at
[email protected] or 1-866-543-2766. push the bolts through the trailer’s lower frame. you should not be able to rotate the right hand bracket inwards (without releasing the red button). tighten the bolts. an automatically engaging locking pin is integrated into this right hand bracket. 3D . pull back on the rear U-frame (the upper portion of the seat wraps around the top of this tube) until the right hand pivoting plastic bracket hooks over the right rear tube. (See 3C). Push the bumper’s front two threaded studs through the holes in the front of the trailer. 3C 3D 3C To prevent accidental folding. Align the bumper to the front of the trailer so that the reflectors are above the bumper. Using the Allen key provided. From the inside of the trailer. There are nuts already installed inside the bumper. To verify that the automatic pin has engaged. For the two side mounting locations. 2C STEP 3 Unfolding and folding the trailer 3A 3B 3A 3B To unfold the trailer’s passenger compartment.STEP 2 2A Assembling the front bumper 2B 2C 2A 2B The bumper mounts to the trailer at the four bumper locations illustrated with arrows. Rotate the left hand plastic pivoting bracket clockwise until it securely hooks over the left rear tube. from the inside of the trailer. thread a nut until hand tight onto each of the threaded studs (Do not tighten with the wrench until after step 2C). The nuts hand tightened in procedure 2B now need to be fully tightened with the wrench provided. From the inside of the trailer’s rear compartment. Place a plastic washer onto each of the two threaded studs (illustrated by the black arrows). pull the upper frame upwards while holding the base of the carrier to the ground. Insert the flag in the slot and into the hole located in the plastic cap. Fully insert the clevis axle into the hollow axle mount located on the side of the trailer (just in front of the parking brake). however if necessary always use rear lights. Slide the flag down into hole until the flag touches the bottom of the tube. test by trying to pull the wheel outwards. Then pull the red button on the right hand bracket towards the rear of the trailer and rotate the right hand bracket inwards. WARNING Always install the safety flag when trailering and attach lights (sold separately) to the rear of the trailer if riding in poor visibility conditions! Failure to do so could result in the trailer not being seen and could result in an accident occurring and serious injuries or death to the occupants! 5B .To fold the trailer. WARNING: Before each ride ensure the wheels and axles are properly assembled! Failure to do so could result in the wheels separating from the trailer and could result in an accident occurring and serious injuries or death to the occupants! STEP 5 Safety flag installation and attaching additional lights (not included) 5A 5B 5A There is a slot located in the upper left corner of the flap covering the rear cargo compartment. IMPORTANT! To ensure the axle system is engaged properly. follow the above steps in reverse order. otherwise you could damage the frame. WARNING Ensure that the pivoting plastic brackets are correctly locked before using the trailer! Failure to do so could cause the carrier to collapse and result in a serious injuries or death to the occupants! STEP 4 Wheel assembly 4A 4B 4A 4B Depress the rubber cap on the wheel hub with your thumb. Once fully inserted. Trailering at night is not recommended. There are two web loops sewn on the upper portion of the flap that covers the rear compartment. remove your thumb from the rubber cap and you should hear a “click” sound. Push the rear U-frame forwards and the trailer will fold flat. Rotate the left hand bracket inwards. Sold separately battery powered lights can be attached to these loops. Note: The red button on the right hand bracket must be released before folding the trailer. The wheel should not move as it is locked in its installed position. tighten these straps. A padded headrest is provided with the carrier. . we recommend that you tip the trailer back on an even and clean surface. If the seat back is too firm. This headrest can be removed for washing. This is done to improve child comfort. so that you have a better view and can more easily familiarise yourself with the attachment system. 7A 7B Align the bolt on the outside of the trailer arm with the slot in the trailer’s black attachment bracket (located on the front lower left side of the trailer). you can loosen these straps slightly. If the seat back begins to sag. 6B STEP 7 Attaching the trailer arm 7A 7B Note: When you first attach the trailer arm. as the tension in the seat back can be adjusted using these straps.STEP 6 Adjusting the seat tension and padded headrest removal 6A 6B 6A Behind the seat you will see the seat is attached using adjustable web straps. held in place by Velcro strips. Push the trailer arm up into the slot as far as possible. The safety pin’s loop must be pulled over end of the pin’s shaft into the locked position. WARNING Before each ride ensure that the hitch coupling is securely tightened on the chain stay and that the back-up safety strap is properly installed (and not damaged)! Failure to do this could result in an accident and serious injury or death to the cyclist and occupants! . Failure to do so could result in the loss of the trailer. Do not ride if there is any damage to the safety strap.22 mm. ensure that the trailer arm’s safety pin is properly locked. Therefore. Do not use the trailer if your bicycle does not fit into this range! 8A 8B 8C 8C 8A 8B Open the hitch coupling’s clamp by turning the large black knob counter-clockwise. IMPORTANT! A hitch coupling that is loosely attached could either slip sideways into the spokes or forwards in the direction of the bottom bracket during braking. Turn the knob clockwise until the knob is very tight and the hitch coupling cannot slide. check that the knob is tight before every ride and regularly during longer rides. 8C Wrap the hitch coupling’s back-up safety strap around the bicycle’s chain stay and clip it onto the d-ring on the trailer arm. The pin should trap the trailer arm in the attachment bracket. so that the pin cannot accidentally fall out. With the trailer arm pivoted all the way up. insert the safety pin through both sides of the attachment bracket. Position the hitch coupling as far rearward as possible on the bicycle’s lower rear tube (chain stay).7C 7D 7E 7C 7D 7E Pivot the trailer arm up into the slot as far as possible. ensuring that they are in good condition. resulting in serious injuries or death to the occupants! STEP 8 Attaching the trailer hitch coupling to your bicycle IMPORTANT! This trailer’s universal hitch coupling is suitable for bicycles with a round or oval chain stay with a tube diameter range of 14 mm . WARNING: Before using the trailer. Regularly inspect the strap’s webbing and hardware. F. To do this you need to un-thread the four vertical shoulder straps from the sleeves on the two padded harnesses. Clip the outermost two shoulder straps (located on either side of the child) into the “D” ring of the outer two crotch straps. and pull the strap ends until the belt is snug. IMPORTANT! Adjust the straps so that the “D” ring is located at the child’s stomach level. E. D. Buckle the lap belt over the child’s lap. Adjust the shoulder straps heights such that the upper buckles are at the same height as the top of the children’s shoulders. This padded harness will now be positioned in the center of the carrier’s seat. This will keep the straps that are not in use out of the way. Undo the lap belt buckle and seat the child in the centre of the trailer. You will then re-thread the two center shoulder straps into the sleeves on one of the padded harnesses. IMPORTANT! Adjust the straps so that the “D” ring is located at the child’s stomach level. Pull the two ends of the each of the shoulder harnesses over the children’s shoulders and clip the buckles located on the ends of the shoulder straps onto the “D” rings located on the crotch straps. we suggest that you store it in the pocket located behind the seat. Undo the lap belt buckle and seat the children side by side in the trailer. Place the crotch strap between the child’s legs. B. Adjust the shoulder straps heights such that the upper buckles are at the same height as the top of the child’s shoulders. Place an outer crotch strap between each of the children’s legs. not at chest level. Pull the shoulder straps loose ends until they are snug. 9B Proper seating position for one child: Note: For the first use of your Kidarooz. WARNING Always attach seat belts and ensure the seat belts are properly attached. C. C. not at chest level. D. G. Pull the two ends of the shoulder harness over the child’s shoulder and clip the buckles located on the ends of the shoulder straps onto the “D” ring located on the center crotch strap.STEP 9 9A Seat belts attachment 9B Proper seating position for two children: A. Buckle the lap belt over both children’s laps. A. E. with buckles securely fastened and no slack in the seat belts! Failure to do so could result in a serious injury or death to the occupants in the event of an accident! 9A . and pull the strap until the belt is snug. you will need to change the seat from having two padded shoulder harnesses into one center positioned harness. Pull the shoulder straps loose ends until they are snug. B. F. So that you do not misplace the second unused padded harness. Regularly stop trailering and check that your children are comfortable and are comfortable in terms of temperature. WARNING: When trailering. always ride with at least the front mesh cover installed. or for improved ventilation. slide the handlebar’s ends into the trailer’s upper frame tube ends. IMPORTANT! In cooler temperatures roll the rain cover and rear flap down. 10A 10B 10C If the temperature is warm. and remember that as inactive passengers they will require more clothing than the cyclist. IMPORTANT! In cool temperatures be sure to dress your children accordingly. . rocks and insects.STEP 10 10A Proper use of the weather cover 10B 10C Your trailer is fitted with a multi-purpose weather cover for climate control and protection from rain. the mesh cover can be rolled up and secured by tucking its ends in the elastic loops on the roof. The rear flap can also be rolled up and secured with the Velcro strips. it is best to always have the front mesh cover rolled down and installed. if desired. Align the holes in the handlebars with the holes in the trailer frame and insert the safety pins from the outside inwards. you can roll up the clear plastic rain cover and secure it by tucking its ends in the elastic loops on the roof. Failure to do this could result in the occupants being injured by flying debris! STEP 11 Attaching the handlebar to the trailer 11A 11B 11A 11B With the bend in the handlebar turning up. For protection. When using the trailer in stroller mode. With the stroller wheel fully inserted. resulting in an accident and serious injury or death to the occupants! WARNING: Always use the safety wrist strap when pushing children in the stroller mode! STEP 12 12A Attaching the stroller caster 12B 12C IMPORTANT! The stroller kit front wheel must be removed when the carrier is used as a bike trailer! 12A 12B 12C Slide the long shaft of the stroller caster into the bracket on the bumper on the front of the trailer. secure the caster by pushing the safety pin fully through the horizontal hole in the bracket. The safety pins loops must be pulled over the ends of the pins shafts into the locked position. WARNING: Before each stroll ensure that the handlebar’s safety pins are properly locked! Failure to do this could result in the loss of the stroller. Failure to do this could result in the caster falling off. WARNING Before each stroll ensure that the stroller caster is secured properly with the pin fully inserted and secured. Slide your hand through the opening of the safety wrist strap.11C 11D 11C 11D The safety pins’ loops must be pulled over the ends of the pins’ shafts into the locked position. so that the pins cannot accidentally fall out. resulting in serious injuries or death to the occupants! . so that the pins cannot accidentally fall out. for maximum safety. so these steps need to be repeated for each wheel. IMPORTANT! The brakes should not be used to bring a rolling trailer to a halt. resulting in serious injuries or death to the occupants! Please keep these instructions in a safe place and refer to them often in order to reacquaint yourself with the important safety information and warnings of this carrier. please contact one of our Customer Service Representatives at:
[email protected] 13 Engaging the parking brake IMPORTANT! Your trailer has an independent parking brake for each wheel. push the trailer lightly to confirm. If you have any questions about the safe use or assembly of this product. To ensure the brake is properly engaged. be sure to supply the instructions if you lend or sell the carrier.E. Calgary.com or by phone: 1-866-543-2766 Made in China For: Kidarooz 6810 6th Street S. push down on the red knob until the lever stops. pull up on the red knob until the lever inserts fully into a slot on the wheel hub. WARNING: Always engage both parking brakes whenever stopped! Failure to do so could result in the trailer rolling away. Also. AB. To release the parking brake. Canada . Be sure to engage both brakes. 13A 13B Push Down Pull up 13A 13B To engage the parking brakes.