ISO-IEC 11801 Ed2.0 Amend 1.2 (SC 25 N 1318)

May 8, 2018 | Author: jjuanzambrano | Category: Electrical Connector, Data Transmission, Electronics, Electrical Engineering, Electromagnetism


Comments



Description

ISO/IEC JTC 1/SC 25 N 1318Date 2007-05-02 Proposed Draft Amendment 1.2 to ISO/IEC 111801 Date: 2007-05-02 Reference number: ISO/IEC JTC 1/SC 25 N 1318 Supersedes document SC 25 N/A THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT SHOULD NOT BE USED FOR REFERENCE PURPOSES. Circulated to P- and O-members, and to technical committees and organizations in liaison for: ISO/IEC JTC 1/SC 25 - voting by (P-members only) INTERCONNECTION OF INFORMATION TECHNOLOGY EQUIPMENT 2007-08-03 Secretariat: Germany (DIN) Please return all votes and comments in electronic form using the attached template directly to the SC 25 Secretariat by the due date indicated. PDAM 1.2 to ISO/IEC 11801 Title: Amendment 1.2 to ISO/IEC 11801: Information technology – Generic cabling for customer premises Project: 1.25.03.02.02-02.02 Introductory This PDAM is distributed for approval as FPDAM. note The proposal for new work has been distributed with SC 25 N 981 and JTC 1 N 7480. The work has been approved as recorded in SC 25 N 1016. The comments to the NWIP have been resolved as recorded in SC 25 N 1046. A WD was distributed with WG 3 N 753. The comments were recorded in WG 3 N 763 and partly resolved in WG 3 N 769. The amendment was split and the first part – with the working title Amendment 1.1 distributed for vote with SC 25 N 1096, N 1173 and N1255. They did not gain substantial support and a 4th FPDAM was distributed with SC 25 N 1324. The left comments to WG 3 N 753 had been resolved with WG 3 N 794 and a WD for Amendment 1.2 was distributed with WG 3 N 795. The comments to this WD have been resolved as recorded in WG 3 N 834 and this PDAM (SC 25 N 1318) was developed. With SC 25 N 1321 the channel and link model has been distributed that provides the means whether the channels as specified in SC 25 N 1324 and the links as drafted in this document can be implemented with the components as drafted in this document. In the published document the cable requirements will be specified by reference to cable specifications. During development of this amendment the reference values are provided in Attachment 1. These values are also subject to comments with respect to there suitability for the channels specified in SC 25 N 1324. REQUESTED: National Member Bodies of ISO/IEC JTC 1/SC 25 are ACTION requested to vote on this document. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights (not listed in the draft) of which they are aware and to provide supporting documentation. Medium: Defined No. of pages: 68 Address Reply to: Secretariat, ISO/IEC JTC 1/SC 25, Dr.-Ing. Walter P. von Pattay Member of ZVEI FV 7 & FV 8, D- 81677 München, Germany Tel.: +49/89/923 967 57 ¸ Tfx.: +49/89/923 967 59 (only on request) EM: [email protected] Home page: http://www.iec.ch/sc25 11801 1 st PDAM 1.2 © ISO/IEC:2007 –1– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 1 Proposed Draft Amendment 1.2 to 2 ISO/IEC 11801:2002, Generic cabling for customer premises 3 FOREWORD 4 Amendment 1.2 to International Standard ISO/IEC 11801 was prepared by subcommittee 25: 5 Interconnection of information technology, of ISO/IEC joint technical committee 1: Information 6 technology. 7 Attention is drawn to the possibility that some of the elements in this amendment may be the subject of 8 patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. 9 __________ 10 Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 11 Table 19 Table 20 Table 21 12 Table 22 13 Table 23 Table 24 14 Table 25 15 Table 26 Table 27 Table 28 Table 29 Table 30 Table 31 –no meaning inserted for automatic numbering only 16 General Changes 17 Update references to tables, the numbers of which have been changed. 18 Pages 14 to 16: 19 2 Normative references 20 Replace: 21 IEC 60068-2-14:1984, Environmental testing - Part 2: Tests. Test N: Change of temperature 22 IEC 60068-2-38:1974, Environmental testing - Part 2: Tests. Test Z/AD: Composite 23 temperature/humidity cyclic test 24 IEC 60512-2:1985, Electromechanical components for electronic equipment; basic testing procedures 25 and measuring methods – Part 2: General examination, electrical continuity and contact resistance 26 tests, insulation tests and voltage stress tests 27 Amendment 1 (1994) 28 IEC 60512-25-5, – Connectors for electronic equipment – Basic tests and measurements – Part 25-5: 29 Test 25e – Return loss 1 30 IEC 60512-25-8:2006 1, Connectors for electronic equipment - Tests and measurements – Part 25-8: 31 Test 25h: – Balance of symmetrical signals 32 IEC 60512-25-9:2006 1, Connectors for electronic equipment – Tests and measurements – Part 25-9: 33 Signal integrity tests – Test 25-X – Alien crosstalk 34 IEC 60603-7-4:2005, Connectors for electronic equipment - Part 7-4: Detail specification for 8-way, 35 unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz 36 IEC 60603-7-41:2006 1, Connectors for electronic equipment - Part 7-41: Detail specification for 8-way, 37 unshielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz and with 38 specified exogenous crosstalk 1 To be published. ISO/IEC JTC 1/SC 25N1318c.doc 1 11801 1 st PDAM 1.2 © ISO/IEC:2007 –2– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 39 IEC 60603-7-5:2005 1, Connectors for electronic equipment - Part 7-5: Detail specification for 8-way, 40 shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz 41 IEC 60603-7-51:2006 1, Connectors for electronic equipment - Part 7-51: Detail specification for 8-way, 42 shielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz and with 43 specified exogenous crosstalk 44 IEC 60603-7-71:2006 1, Connectors for electronic equipment – Part 7-71: Detail specification for 8-way, 45 shielded, free and fixed connectors, for data transmission with frequencies up to 1000 MHz 2 46 IEC/PAS 60793-1-49:2002, Optical fibres – Part 1-49: Measurement methods and test procedures – 47 Differential mode delay 48 IEC/PAS 61076-3-104:2002, Connectors for electronic equipment – Part 3-104: Detail specification for 49 8-way, shielded free and fixed connectors, for data transmissions with frequencies up to 600 MHz 50 IEC 61156-1:1994, Multicore and symmetrical pair/quad cables for digital communications – Part 1: 51 Generic specification 3 52 Amendment 1:1999 53 Amendment 2:2001 54 IEC 61156-2:1995, Multicore and symmetrical pair/quad cables for digital communications – Part 2: 55 Horizontal floor wiring – Sectional specification 4 56 Amendment 1:1999 57 Amendment 2:2001 58 IEC 61156-3:1995, Multicore and symmetrical pair/quad cables for digital communications – Part 3: 59 Multicore and symmetrical pair/quad cables for digital communications – Part 3: Work area wiring – 60 Sectional specification 5 61 Amendment 1:1999 62 Amendment 2:2001 63 IEC 61156-4:1995, Multicore and symmetrical pair/quad cables for digital communications – Part 4: 64 Riser cables – Sectional specification 6 65 Amendment 1:1999 66 Amendment 2:2001 67 IEC 61156-5:2002, Multicore and symmetrical pair/quad cables for digital communications – Part 5: 68 Symmetrical pair/quad cables with transmission characteristics up to 600 MHz – Horizontal floor wiring – 69 Sectional specification 70 IEC 61156-6:2002, Multicore and symmetrical pair/quad cables for digital communications – Part 6: 71 Symmetrical pair/quad cables with transmission characteristics up to 600 MHz – Work area wiring – 72 Sectional specification 2 This standard is currently at edition 1.0 , published 2002. Edition 2.0 of IEC 60603-7-7 is targeted for publication in 2006. 3 There exists a consolidated edition 1.2 (2001) of IEC 61156-1 that includes edition 1.0 (1994) and its amendments 1 (1999) and 2 (2001). 4 There exists a consolidated edition 1.2 (2001) of IEC 61156-2 that includes edition 1.0 (1995) and its amendments 1 (1999) and 2 (2001). 5 There exists a consolidated edition 1.2 (2001) of IEC 61156-3 that includes edition 1.0 (1995) and its amendments 1 (1999) and 2 (2001). 6 There exists a consolidated edition 1.2 (2001) of IEC 61156-4 that includes edition 1.0 (1995) and its amendments 1 (1999) and 2 (2001). ISO/IEC JTC 1/SC 25N1318c.doc 2 11801 1 st PDAM 1.2 © ISO/IEC:2007 –3– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 73 IEC 61935-1:2000, Generic cabling systems – Specifications for the testing of balanced communication 74 cabling in accordance with ISO/IEC 11801 – Part 1: Installed cabling 75 Amendment 1 (under consideration) 76 IEC 61935-2, – Generic cabling systems – Specification for the testing of balanced communication 77 cabling in accordance with ISO/IEC 11801 – Part 2: Patch cords and work area cords 1 78 ISO/IEC TR 14763-1, Information technology – Implementation and operation of customer premises 79 cabling – Part 1: Administration 80 ISO/IEC 18010:2002, Information technology – Pathways and spaces for customer premises cabling 81 By: 82 IEC 60512-1-1, Connectors for electronic equipment - Tests and measurements – Part 1-1: General 83 examination - Test 1a: Visual examination 84 IEC 60512-1-2, Connectors for electronic equipment - Tests and measurements – Part 1-2: General 85 examination - Test 1b: Examination of dimension and mass 86 IEC 60512-2-1, Connectors for electronic equipment - Tests and measurements – Part 2-1: Electrical 87 continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method 88 IEC 60512-2-5, Connectors for electronic equipment - Tests and measurements – Part 2-5: Electrical 89 continuity and contact resistance tests - Test 2e: Contact disturbance 90 IEC 60512-3-1, Connectors for electronic equipment - Tests and measurements – Part 3-1: Insulation 91 tests - Test 3a: Insulation resistance 92 IEC 60512-4-1, Connectors for electronic equipment - Tests and measurements – Part 4-1: Voltage 93 stress tests - Test 4a: Voltage proof 94 IEC 60512-5-2, Connectors for electronic equipment - Tests and measurements – Part 5-2: Current- 95 carrying capacity tests - Test 5b: Current-temperature derating 96 IEC 60512-6-4, Connectors for electronic equipment - Tests and measurements – Part 6-4: Dynamic 97 stress tests - Test 6d: Vibration (sinusoidal) 98 IEC 60512-9, Electromechanical components for electronic equipment; basic testing procedures and 99 measuring methods - Part 9: Miscellaneous tests 100 IEC 60512-11-7, Connectors for electronic equipment - Tests and measurements – Part 11-7: Climatic 101 tests - Test 11g: Flowing mixed gas corrosion test 102 IEC 60512-13-1, Electromechanical components for electronic equipment - Basic testing procedures 103 and measuring methods - Part 13: Mechanical operating tests - Section 1: Test 13a: Engaging and 104 separating forces 105 IEC 60512-15-6 1, Electromechanical components for electronic equipment - Basic testing procedures 106 and measuring methods - Part 15: Mechanical tests on contacts and terminations - Section 8: Test 15F: 107 Effectiveness of connector coupling devices (under consideration 108 IEC 60512-15-8, Electromechanical components for electronic equipment - Basic testing procedures 109 and measuring methods - Part 15: Mechanical tests on contacts and terminations - Section 8: Test 15h - 110 Contact retention system resistance to tool application ISO/IEC JTC 1/SC 25N1318c.doc 3 11801 1 st PDAM 1.2 © ISO/IEC:2007 –4– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 111 IEC 60512-25-5, Connectors for electronic equipment - Tests and measurements – Part 25-5: Test 25e - 112 Return loss 113 IEC 60793-1-49, Optical fibres – Part 1-49: Measurement methods and test procedures – Differential 114 mode delay 115 IEC 60603-7-7:2006, Connectors for electronic equipment – Part 7-7: Detail specification for 8-way, 116 shielded, free and fixed connectors, for data transmission with frequencies up to 600 MHz 117 IEC 60603-7-71:2007, Connectors for electronic equipment – Part 7-71: Detail specification for 8-way, 118 shielded, free and fixed connectors, for data transmission with frequencies up to 1000 MHz 119 IEC 61076-3-104:2006, Connectors for electronic equipment – Part 3-104: Detail specification for 8-way, 120 shielded free and fixed connectors, for data transmissions with frequencies up to 1000 MHz 121 IEC 61156-1:2007 1 , Multicore and symmetrical pair/quad cables for digital communications – Part 1: 122 Generic specification 7 123 IEC 61156-2:2007 1 , Multicore and symmetrical pair/quad cables for digital communications – Part 2: 124 Horizontal floor wiring – Sectional specification 7 125 IEC 61156-3:2007 1 , Multicore and symmetrical pair/quad cables for digital communications – Part 3: 126 Multicore and symmetrical pair/quad cables for digital communications – Part 3: Work area wiring – 127 Sectional specification 8 128 IEC 61156-4:2007 1 Multicore and symmetrical pair/quad cables for digital communications – Part 4: 129 Riser cables – Sectional specification 9 130 IEC 61156-5:2007 1 , Multicore and symmetrical pair/quad cables for digital communications – Part 5: 131 Symmetrical pair/quad cables with transmission characteristics up to 1000 MHz – Horizontal floor wiring 132 – Sectional specification 10 133 IEC 61156-6:2007 1 , Multicore and symmetrical pair/quad cables for digital communications – Part 6: 134 Symmetrical pair/quad cables with transmission characteristics up to 1000 MHz – Work area wiring – 135 Sectional specification 11 136 IEC 61754-20:2002, Fiber optic connector interfaces – Part 20: Type LC connector family 137 IEC 61935-2, – Generic cabling systems – Specification for the testing of balanced communication 138 cabling in accordance with ISO/IEC 11801 – Part 2: Patch cords and work area cords 12 139 Insert, in the existing list, the titles of the following standards and amendments: 140 IEC 60068-2-14, Environmental testing - Part 2: Tests. Test N: Change of temperature 141 IEC 60068-2-38, Environmental testing - Part 2: Tests. Test Z/AD: Composite temperature/humidity 142 cyclic test 7 This standard is currently at edition 2.0, published 2003. Edition 3 of IEC 61156-2 is targeted for publication in 2007 8 This standard is currently at edition 2.0, published 2003. Edition 3 of IEC 61156-3 is targeted for publication in 2007 9 This standard is currently at edition 2.0, published 2003. Edition 3 of IEC 61156-4 is targeted for publication in 2007 10 This standard is currently at edition 2.0, published 2002 as referenced in 11801. Edition 3 of IEC 61156-5 is targeted for publication in 2007 11 This standard is currently at edition 2.0, published 2002 as referenced in 11801. Edition 3 of IEC 61156-6 is targeted for publication in 2007 12 This standard is currently at edition 2.0, published 2005. Edition 2 of IEC 61935-1 or an amendment is needed to support measurements to 1000 MHz. Publication date pending confirmation from IEC TC46. ISO/IEC JTC 1/SC 25N1318c.doc 4 11801 1 st PDAM 1.2 © ISO/IEC:2007 –5– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 143 IEC 60512-25-8, 1, Connectors for electronic equipment - Tests and measurements - Part 25-8: Test 144 25h: – Balance of symmetrical signals 145 IEC 60512-25-XX, 1, Connectors for electronic equipment – Tests and measurements – Part 25-XX: 146 Signal integrity tests – Test 25-X – Alien crosstalk 147 IEC 60603-7-4:2005, Connectors for electronic equipment - Part 7-4: Detail specification for 8-way, 148 unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz 149 IEC 60603-7-4-1:200x 1, Connectors for electronic equipment - Part 7-4, Amendment 1: Detail 150 specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies 151 up to 500 MHz 152 IEC 60603-7-52007-03, Connectors for electronic equipment - Part 7-5: Detail specification for 8-way, 153 shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz 154 IEC 60603-7-5-1:200x 1, Connectors for electronic equipment - Part 7-4, Amendment 1: Detail 155 specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up 156 to 500 MHz 157 Page 55 158 8.1 General 159 Add the following new sentence before the last paragraph in 8.1: 160 For single mode transmission channels, where lower attenuation or longer distances are required for a 161 given channel, the OS2 cable and the longer distance channels specified in ISO/IEC 24702 may be 162 considered. 163 8.2 Component choice 164 Replace first paragraph: 165 The required channel lengths, applications to be supported and the life expectancy of the cabling will 166 determine the selection of optical fibre components. The performance requirements for optical fibre 167 channels are based on the use of a single optical wavelength in each specified transmission window. 168 By: 169 The required channel lengths, the applications to be supported and the life expectancy of the cabling 170 will determine the selection of optical fibre components. 171 Page 58 172 9.1 General 173 Replace in 1 st paragraph: 174 The requirements for current clause apply to a reference temperature of 20° C. 175 By: 176 The requirements of the current clause apply to any environmental condition at which the cable has to 177 operate. ISO/IEC JTC 1/SC 25N1318c.doc 5 11801 1 st PDAM 1.2 © ISO/IEC:2007 –6– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 178 (No meaning for numbering purpuses only Table 32 Table 33 Table 34 Table 35 ) 179 Page 58 180 9.2.1 Basic performance requirements 181 Replace Table 24, now Table 36. 182 Table 36 – Basic requirements for balanced cables: Sectional specification for multicore and symmetrical pair/quad cables for digital IEC 61156-2 (2001) communications – Horizontal wiring Sectional specification for multicore and symmetrical pair/quad cables for digital IEC 61156-3 (2001) communications – Work area wiring Sectional specification for multicore and symmetrical pair/quad cables for digital IEC 61156-4 (2001) communications – Riser cables Symmetrical pair/quad cables for digital communications with transmission IEC 61156-5 (2002) characteristics up to 600 MHz – Part 5: Horizontal wiring Symmetrical pair/quad cables for digital communications with transmission IEC 61156-6 (2002) characteristics up to 600 MHz – Part 6: Work area wiring NOTE The pair-to-pair NEXT of category 6 is 1 dB more restrictive than needed to fulfil Clause 7 using the reference implementation of Clause 7. 183 By Sectional specification for multicore and symmetrical pair/quad cables for digital IEC 61156-2 (2006) communications – Horizontal wiring Sectional specification for multicore and symmetrical pair/quad cables for digital IEC 61156-3 (2006) communications – Work area wiring Sectional specification for multicore and symmetrical pair/quad cables for digital IEC 61156-4 (2006) communications – Riser cables Symmetrical pair/quad cables for digital communications with transmission IEC 61156-5 (2007) a, b characteristics up to 1000 MHz – Part 5: Horizontal wiring Symmetrical pair/quad cables for digital communications with transmission IEC 61156-6 (2007) a characteristics up to 1000 MHz – Part 6: Work area wiring a To be published. b IEC 61156-7:Part 7 Symmetrical pair cables with transmission characteristics up to 1200 MHz – Sectional specification for digital and analog communications cables also meet the requirements for category 7 cable. 184 Note: ISO/IEC JTC 1/SC25 WG3 has sent a liaison letter (ISO/IEC JTC 1/SC 25/WG3 N824) to IEC SC46C requesting category 185 7A NEXT requirements to be increased by 3,0 dB in order for the channel and link requirements to be satisfied. 186 Secretary’s Note 187 During the development of this amendment the minimum requirements for cables with respect to their 188 suitability for channels and links are listed in Attachment 1. This covers the facts that cable 189 specifications for category 6 A and 7 A are still under discussion and that the minimum requirements are 190 subject to change should simulations show that there is a need to change the component values in 191 order to meet the channel requirements as specified in SC 25 N 1324. 192 These values are also subject to comment. 193 End of secretary’s note 194 Page 59 195 9.2.2.5 ELFEXT and PS ELFEXT 196 Replace: 197 Last sentence of 9.2.2.5: If FEXT is greater than 70 dB, ELFEXT and PSELFEXT need not be 198 measured. ISO/IEC JTC 1/SC 25N1318c.doc 6 11801 1 st PDAM 1.2 © ISO/IEC:2007 –7– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 199 By: 200 ACR-F at frequencies that correspond to measured FEXT values of greater than 70 dB, are for 201 information only. PSACR-F at frequencies that correspond to computed PSFEXT values of greater than 202 67 dB are for information only. 203 Page 60 204 Replace: 205 9.3 Additional crosstalk considerations for cable sharing in balanced cables 206 9.3.1 General 207 This subclause covers cabling system implementations that may lead to the presence of multiple signals 208 on the same cable. 209 By: 210 9.3 Additional crosstalk considerations for balanced cables 211 9.3.1 Cable sharing 212 9.3.2 to 9.3.3 cover cabling system implementations that may lead to the presence of multiple 213 signals on the same cable. 214 Editors note the former general need to be changed as only applicable to a part of the clause by now 215 Page 61 216 Insert: 217 9.3.4 Alien crosstalk 218 Cables used in class E A and class F A channels shall meet alien crosstalk requirements for category 6 A 219 and category 7 A respectively, as specified in IEC 61156-5 and IEC 61156-6. 220 (No meaning: Table 37, Table 38 just inserted for automatic numbering) ) 221 Page 62 222 9.4.3 Multimode optical fibre cable 223 Replace NOTE in former Table 27, now Table 39 by: 224 NOTE Effective laser launch bandwidth is assured using differential mode delay (DMD) as specified in IEC 60793-1-49. 225 Optical fibres that meet only the overfilled launch modal bandwidth may not support some applications specified in Annex F ISO/IEC JTC 1/SC 25N1318c.doc 7 11801 1 st PDAM 1.2 © ISO/IEC:2007 –8– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 226 Pages 65 to 66 227 10.2.3 Mechanical characteristics 228 Table 28, now Table 40, block “a” – add lines that provide the reference to IEC 60603-7-41, -51, and – 229 71 for 6 A unscreened, 6 A screened, 7 A respectively (example new Table 41 below) 230 Delete footnotes “i, k, m, n“ in former Table 28, now Table 40 231 Page 66 232 10.2.3 Mechanical characteristics 233 Replace footnote “o“ in former Table 28, now Table 28, now Table 40 o 234 In installations where other factors, such as HEM (see ISO/IEC 15018) applications, take preference over backward 235 compatibility offered with IEC 60603-7-7, the interface specified in IEC/PAS 61076-3-104/Ed.1 may also be used. 236 By: i 237 In installations where other factors, such as BCT (see ISO/IEC 15018) applications, take preference over backward 238 compatibility offered with IEC 60603-7-7, the interface specified in IEC 61076-3-104 may also be used. 239 Page 67 240 10.2.4.2 Telecommunications outlets 241 Replace former Table 29, now Table 41 with the following table 242 Table 41 - Electrical characteristics of telecommunications outlet is intended for use with 243 balanced cabling Electrical characteristics of the a telecommunications outlet Component or test Requirement standard Frequency range Interface type MHz Category 5 unscreened d.c., 1 to 100 All IEC 60603-7-2 Category 5 screened d.c., 1 to 100 All IEC 60603-7-3 Category 6 unscreened d.c., 1 to 250 All IEC 60603-7-4 Category 6 screened d.c., 1 to 250 All IEC 60603-7-5 b Category 6 A unscreened d.c., 1 to 500 All IEC 60603-7-41 b Category 6 A screened d.c., 1 to 500 All IEC 60603-7-51 c Category 7 d.c., 1 to 600 All IEC 60603-7-7 b, c Category 7 A d.c., 1 to 1000 All IEC 60603-7-71 a Mating and unmating under load is f.f.s. b At the time of publication IEC 60603-7-41, -51 and -71 were not available. Until these specifications are available compliance to requirements that refer to IEC 60603-7-4, -5 and –7 may be attained by full compliance with IEC 60603-7, combined with all applicable requirements of Clause 10 of this standard. c In installations where other factors, such as BCT (see ISO/IEC 15018) applications, take preference over backward compatibility offered with IEC 60603-7-7, the interface specified in IEC 61076-3-104 may also be used. ISO/IEC JTC 1/SC 25N1318c.doc 8 11801 1 st PDAM 1.2 © ISO/IEC:2007 –9– ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 244 Pages 68 to 72 245 10.2.4.3 Connecting hardware for use in distributors and consolidation points 246 Replace tables 30 to 41, 42, 43 and 44 by the following Table 42 to Table 53, Table 55, Table 57 and 247 Table 58. Insert Table 54,, Table 60,Table 59 and Table 60 as provided below: 248 Table 42 – Return loss Electrical Requirement characteristics Frequency Test MHz Connector category standard 5 6 6A 7 7A Minimum return loss a 1 to 100 60 – 20 lg(f) – - - – dB 1 to 250 – 64 – 20 lg(f) - - – 1 - 500 - - 68 – 20 lg(f) - - 1 to 600 - - - 68 – 20 lg(f) - 1 to 1000 – – _ - 68 – 20 lg(f) IEC 60512 -25-5 1 30,0 30,0 30,0 30,0 30,0 100 20,0 24,0 28,0 28,0 28,0 Minimum return loss at key 250 N/A 16,0 20,0 20,0 20,0 frequencies 500 N/A N/A 14,0 14,0 14,0 dB 600 N/A N/A N/A 12,4 12,4 1000 N/A N/A N/A N/A 8,0 a Return loss at frequencies that correspond to calculated values of greater than 30,0 dB shall revert to a minimum requirement of 30,0 dB. 249 Table 43 – Insertion loss Requirement Electrical Frequency Test Connector category characteristics MHz standard 5 6 6A 7 7A – 1 to 100 0,04 f - - – – 1 to 250 - 0,02 f - - - Maximum a insertion loss 1 to 500 – – - – 0,02 f dB 1 to 600 - - - 0,02 f - IEC 60512 1 to 1000 – - - - 0,02 f -25-2 1 0,10 0,10 0,10 0,10 0,10 100 0,40 0,20 0,20 0,20 0,20 Maximum insertion loss at 250 N/A 0,32 0,32 0,32 0,32 key frequencies 500 N/A N/A 0,45 0,45 0,45 dB 600 N/A N/A N/A 0,50 0,50 1000 N/A N/A N/A N/A 0,63 a Insertion loss at frequencies that correspond to calculated values of less than 0,1 dB shall revert to a requirement of 0,1 dB maximum. ISO/IEC JTC 1/SC 25N1318c.doc 9 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 10 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 250 251 Table 44 – Near end crosstalk (NEXT) Requirement Electrical Frequency Connector category Test standard characteristics MHz 5 6 6A 7 7A 83 – 20 lg 1 to 100 – - - – (f) 1 to 250 – 94 – 20 lg(f) 94 – 20 lg(f) - – Minimum near end crosstalk 46,04- 250 to 500 - - - – (NEXT) a 30lg(f/250) dB 1 to 600 - - - 102,4– 15lg(f) 116,3 – 20 lg(f) 600 to – – - - 60,73-40lg(f/600) 1 000 IEC 60512-25-1 1 75,0 75,0 75,0 75,0 75,0 100 43,0 54,0 54,0 72,4 75,0 Minimum NEXT at key 250 N/A 46,0 46,0 66,4 68,3 frequencies 500 N/A 37,0 61,9 62,3 dB 600 N/A N/A N/A N/A 60,7 1000 N/A N/A N/A N/A 51,8 a NEXT at frequencies that correspond to calculated values of greater than 75,0 dB shall revert to a minimum requirement of 75,0 dB. Editor’s note: A liaison letter (3N824 dated 2007-03-06) has been sent to SC46C requesting an increase in Category 7 A cable NEXT. 252 Table 45 – Power sum near end crosstalk (PS NEXT) 253 (for information only) b Requirement Electrical Frequency Test characteri Connector category MHz standard stics 5 6 6A 7 7A 1 to 100 80 – 20 lg(f) – - - – Minimum 1 to 250 – 90 – 20 lg(f) 90 – 20 lg(f) - – power sum near end 42,04- 250 to 500 – - - – crosstalk 30lg(f/250) (PS NEXT) a 1 to 600 - - - 99,4 – 15 lg(f) 113,3-20*log(f) dB 57,73- 600 to 1000 – – - - 40lg(f/600)) IEC 60512 -25-1 1 72,0 72,0 72,0 72,0 72,0 Minimum 100 40,0 50,0 50,0 69,4 72,0 PS NEXT at key 250 N/A 42,0 42,0 63,4 65,3 frequencie 500 N/A N/A 33,0 58,9 59,3 s dB 600 N/A N/A N/A 57,7 57,7 1000 N/A N/A N/A N/A 48,9 a PS NEXT at frequencies that correspond to calculated values of greater than 72,0 dB shall revert to a minimum requirement of 72,0 dB. b Equations and values for power sum NEXT are provided for information only. ISO/IEC JTC 1/SC 25N1318c.doc 10 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 11 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 254 Table 46 – Far end crosstalk (FEXT) Requirement Electrical Frequency characteris Connector category Test standard MHz tics 5 6 6A 7 7A 1 to 100 75,1 – 20 lg(f) – – - – Minimum 1 to 250 – 83,1 – 20 lg(f) - - – far end 1 to 500 – - 83,1 – 20 lg(f) – crosstalk (FEXT) a, b 1 to 600 - - - 90 – 15 lg(f) - dB 103,9- 1 to 1000 – – – - 20*lg(f) IEC 60512-25-1 1 65,0 65,0 65,0 65,0 65,0 100 35,1 43,1 43,1 60,0 63,9 Minimum FEXT at 250 N/A 35,1 35,1 54,0 55,9 key frequencies 500 N/A N/A 29,1 49,5 49,9 dB 600 N/A N/A N/A 48,3 48,3 1000 N/A N/A N/A N/A 43,9 a FEXT at frequencies that correspond to calculated values of greater than 75,0 dB shall revert to a minimum requirement of 75,0 dB. b For connectors, the difference between FEXT and ACR-F is minimal. Therefore, connector FEXT requirements are used to model ACR-F performance for links and channels. 255 Table 47 – Power sum far end crosstalk (PS FEXT) 256 (for information only) c Requirement Electrical Frequency Test Connector category characteristics MHz standard 5 6 6A 7 7A 1 to 100 72,1 – 20 lg(f) - - – Minimum power 1 to 250 – 80,1 – 20 lg(f) – sum far end crosstalk 1 to 500 – - 80,1 – 20 lg(f) – (PS FEXT) a, b dB 1 to 600 - - - 87 – 15 lg(f) 1 to 1000 – – – 100,9-20lg(f) IEC 6051 1 72,0 72,0 72,0 72,0 72,0 2-25-1 100 32,1 40,1 40,1 57,0 60,9 Minimum PS FEXT 250 N/A 32,1 32,1 51,0 52,9 at key frequencies dB 500 N/A N/A 26,1 46,5 46,9 600 N/A N/A N/A 45,3 45,3 1000 N/A N/A N/A N/A 40,9 A PS FEXT at frequencies that correspond to calculated values of greater than 72,0 dB shall revert to a minimum requirement of 72,0 dB. b For connectors, the difference between PS FEXT and PS ELFEXT is minimal. Therefore, connector PS FEXT requirements are used to model PS ELFEXT performance for links and channels. c Equations and values for PS FEXT are provided for information only. ISO/IEC JTC 1/SC 25N1318c.doc 11 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 12 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 257 Table 48 – Input to output resistance Requirement Electrical characteristics Frequency Connector category Test standard 5 6 6A 7 7A Maximum input to output IEC 60512-2-1 resistance a d.c. 200 200 200 200 200 Test 2a mΩ 258 Table 49 – Input to output resistance unbalance Requirement Electrical characteristics Frequency Connector category Test standard 5 6 6A 7 7A a Maximum input to output IEC 60512-2-1 resistance unbalance d.c. 50 50 50 50 50 Test 2a mΩ 259 Table 50 – Current carrying capacity Requirement Electrical characteristics Frequency Connector category Test standard 5 6 6A 7 7A Minimum current carrying IEC 60512-5-2 d.c. 0,75 0,75 0,75 0,75 0,75 capacity a, b, c A Test 5b a Applicable for an ambient temperature of 60 °C. b Applicable to each conductor including the screen, if present. c The requirement for current carrying capacity assumes that the connector will not be subject to mating and unmating under load. 260 Table 51 – Propagation delay 261 (for information only) Requirement Frequency Connector category Electrical characteristics Test standard MHz 5 6 6A 7 7A – 1 to 100 2,5 – 1 to 250 – 2,5 Maximum propagation delay 1 to 500 – – 2,5 – IEC 60512-25-4 ns 1 to 600 – – – 2,5 1 to 1000 – – – – 2,5 Note: This parameter is met by design ISO/IEC JTC 1/SC 25N1318c.doc 12 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 13 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 262 Table 52 – Delay skew 263 (for information only) Requirement Frequency Connector category Electrical characteristics Test standard MHz 5 6 6A 7 7A – 1 to 100 1,25 – 1 to 250 – 1,25 Maximum delay skew 1 to 500 – – 1,25 IEC 60512-25-4 ns 1 to 600 – – – 1,25 – 1 to 1000 – – – – 1,25 Note: This parameter is met by design 264 Table 53 – Transverse conversion loss (TCL) Requirement Electrical Frequency Connector category characterist Test standard MHz ics 5 6 6A 7 7A 1 to 100 66 – 20 lg(f) – - - – 68 – 20 lg(f) 1 to 250 – b - - – Minimum transverse 68 – 20 lg(f) conversion 1 to 500 - - b - - loss (TCL) a dB 68 – 20 lg(f) 1 to 600 - - - b - b 1 to 1000 – – - - 68 – 20 lg(f) IEC 60512-25-8 1 60,0 62,0 62,0 62,0 62,0 100 26,0 28,0 28,0 28,0 28,0 Minimum TCL at key 250 N/A 20,0 20,0 20,0 20,0 frequencies 500 N/A N/A f.f.s. f.f.s. f.f.s. dB 600 N/A N/A N/A f.f.s. f.f.s. 1000 N/A N/A N/A N/A f.f.s. a TCL at frequencies that correspond to calculated values of greater than 50,0 dB shall revert to a minimum requirement of 50,0 dB. b The applicability of this equation and test standard at frequencies above 250 MHz is f.f.s. ISO/IEC JTC 1/SC 25N1318c.doc 13 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 14 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 265 Table 54 – Transverse conversion transfer loss (TCTL) Requirement Electrical Frequency Test characterist Connector category MHz standard ics 5 6 6A 7 7A 1 to 100 66 – 20 lg(f) – - - – 68 – 20 lg(f) Minimum 1 to 250 – b - - – transverse conversion 68 – 20 lg(f) 1 to 500 - - b - - loss (TCTL) a dB 68 – 20 lg(f) 1 to 600 - - - b - 1 to 1000 – – - - 68 – 20 lg(f) b IEC 60512 -25-8 1 60,0 62,0 62,0 62,0 62,0 100 26,0 28,0 28,0 28,0 28,0 Minimum TCTL at key 250 N/A 20,0 20,0 20,0 20,0 frequencies 500 N/A N/A f.f.s. f.f.s. f.f.s. dB 600 N/A N/A N/A f.f.s. f.f.s. 1000 N/A N/A N/A N/A f.f.s. a TCTL at frequencies that correspond to calculated values of greater than 50,0 dB shall revert to a minimum requirement of 50,0 dB. b The applicability of this equation and test standard at frequencies above 250 MHz is f.f.s. 266 Table 55 – Transfer impedance (screened connectors only) Requirement Frequency Electrical characteristics Connector category Test standard MHz 5 6 6A 7 7A Maximum transfer 1 to 10 0,1 f 0,3 0,1 f 0,3 0,1 f 0,3 0,05 f 0,3 0,05 f 0,3 impedance Ω 0,01 f 0,01 f 10 to 80 0,02 f 0,02 f 0,02 f IEC 60512-26 Maximum transfer 1 0,10 0,10 0,10 0,05 0,05 impedance at key frequencies 10,0 0,20 0,20 0,20 0,10 0,10 Ω 80,0 1,60 1,60 1,60 0,80 0,80 267 Table 56 – Coupling attenuation (screened connectors only) Requirement Electrical Frequency Test characterist Connector category MHz standard ics 5 6 6A 7 7A Minimum 30 to 100 ≥35 ≥35 ≥35 ≥75 ≥75 coupling attenuation 100 to 1000 75-20lg(f) 75-20lg(f) 75-20lg(f) 75-20lg(f) 75-20lg(f) 30 35,0 35,0 35,0 75,0 75,0 100 35,0 35,0 35,0 75,0 75,0 EN 50289- Minimum 1-14 coupling 250 27,0 27,0 27,0 27,0 27,0 attenuation 500 21,0 21,0 21,0 21,0 21,0 dB 600 19,4 19,4 19,4 19,4 19,4 1 000 15,0 15,0 15,0 15,0 15,0 ISO/IEC JTC 1/SC 25N1318c.doc 14 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 15 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 268 269 Table 57 – Insulation resistance Requirement Electrical characteristics Frequency Connector category Test standard 5 6 6A 7 7A IEC 60512-3-1 Minimum insulation Test 3a, resistance d.c. 100 100 100 100 100 Method C MΩ 500 V d.c. 270 Table 58 – Voltage proof Requirement Electrical characteristics Frequency Connector category Test standard 5 6 6A 7 7A Minimum voltage proof V d.c. 1 000 1 000 1 000 1 000 1 000 Conductor to conductor IEC 60512-4-1 Test 4a Minimum voltage proof V d.c. 1 500 1 500 1 500 1 500 1 500 Conductor to test panel 271 Table 59 – Power sum alien near end crosstalk (PS ANEXT) Requirement b Frequency Electrical characteristics Connector category Test standard MHz 6A 7A Minimum power sum alien 1 to 500 110,5-20lg(f) ffs – near end crosstalk (PS ANEXT) a 1 to 1 000 – 110,5-20lg(f) dB 1 110,5 110,5 c IEC 60512-25-9 100 70,5 70,5 Minimum PS ANEXT at key frequencies 250 62,5 62,5 dB 500 56,5 56,5 1000 N/A 50,5 a PS ANEXT at frequencies that correspond to calculated values of greater than 72,0 dB shall revert to a minimum requirement of 72,0 dB. c IEC 60512-25-9 is pending publication. ISO/IEC JTC 1/SC 25N1318c.doc 15 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 16 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 272 Table 60 – Power sum alien far end crosstalk (PS AFEXT) c Requirement Frequency Electrical characteristics Connector category Test standard MHz 6A 7A Minimum power sum alien 1 to 500 107-20Lg(f) – far end crosstalk (PS AFEXT) a, b 1 to 1 000 – 107-20Lg(f) dB 1 107 107 IEC 60512-25-X d Minimum PS AFEXT at key 250 59 59 frequencies dB 500 53 53 1000 N/A 47 a PS AFEXT at frequencies that correspond to calculated values of greater than 72,0 dB shall revert to a minimum requirement of 72,0 dB. b For connectors, the difference between PS AFEXT and PSAACR-F is minimal. Therefore, connector PS AFEXT requirements are used to model PSAACR-F performance for links and channels. d IEC 60512-25-X is pending publication. 273 (no meaning: Table 61, Table 62, just inserted for automatic numbering reasons ) 274 Page 75 275 Replace: 276 10.3.3 Mechanical and optical characteristics 277 The optical fibre cables in the work area shall be connected to horizontal cabling at the 278 Telecommunications outlet with a duplex SC-connector, SC-D), that complies with IEC 60874-19-1. 279 The optical fibre connector used at the TO shall meet the requirements of 10.3.3. 280 By: 281 The optical fibre cables in the work area shall be connected to horizontal cabling at the 282 Telecommunications outlet (TO) with a duplexable LC connector that complies with IEC 61754-20. 283 The optical fibre connector used at the TO shall meet the requirements of 10.3.3. 284 Pages 79 to 81 285 13 Balanced cords 286 Replace 13.3 and 13.4 by the following. Re-index all tables and equations after 6.4.14: 287 13.3 Return loss 288 Balanced cords shall meet return loss (RL) requirements specified in Table 63. The cords shall meet the 289 electrical and mechanical properties of IEC 61935-2. ISO/IEC JTC 1/SC 25N1318c.doc 16 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 17 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 290 Table 63 – Minimum return loss for balanced cords Frequency Return loss MHz dB Category 5 Category 6 Category 6 A Category 7 Category 7 A 1 ≤ f < 25 19,8 + 3 lg(f) 19,8 + 3 lg(f) 19,8 + 3 lg(f) 19,8 + 3 lg(f) 19,8 + 3 lg(f) 25 ≤ f ≤ 100 38,0 – 10 lg(f) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 25 ≤ f ≤ 250 38,0 – 10 lg(f) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 250 ≤ f ≤500 N/A N/A 14-15lg(f/250) 38,0 – 10 lg(f) 38,0 – 10 lg(f) 500 ≤ f ≤600 N/A N/A N/A 38,0 – 10 lg(f) 38,0 – 10 lg(f) 600 ≤ f ≤1 000 N/A N/A N/A N/A ffs 291 Table 64 – Informative values of return loss for balanced cords at key frequencies Return Loss Frequency dB MHz Category 5 Category 6 Category 6 A Category 7 Category 7 A 1 19,8 19,8 19,8 19,8 19,8 100 18,0 18,0 18,0 18,0 18,0 250 N/A 14,0 14,0 14,0 14,0 500 N/A N/A 9,5 11,0 11,0 600 N/A N/A N/A 10,2 10,2 1 000 N/A N/A N/A N/A ffs 292 13.4 NEXT 293 Balanced cords shall meet the requirement of equations (6) to (10) when measured in accordance with 294 IEC 61935-2. ⎛ − ⎛⎜ NEXT + 2 ⋅ IL ⎞ ⎞ ⎜ connector ⎟⎠ ⎟ ⎜ − NEXTconnectors ⎝ cable, L 295 ⎟ (9) ⎜ 10 10 ⎟ NEXT = − 10 lg ⎜10 + 10 ⎟ + RSXT cord ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ 296 where 297 NEXT cord is the NEXT of the entire cord 298 NEXT connectors is the NEXT of both connectors in the cord, taking insertion loss into account. 299 NEXT cable, L is the NEXT of the cable adjusted for length 300 IL connector is the insertion loss of one connector 301 RSXT is the reflected signal cross talk 302 NOTE All variable are expressed in dB 303 with 304 RSXT = 0 dB for category 5 cords 305 RSXT = 0,5 dB for category 6, category 6 A , category 7 and category 7 A cords. 306 and ISO/IEC JTC 1/SC 25N1318c.doc 17 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 18 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 ⎛ ⎛ ⎞⎞ ⎜ − NEXT − NEXT + 2 ⎜⎜ IL + IL ⎟ 307 ⎜ local remote ⎝ cable connector ⎟⎠ ⎟⎟ (10) NEXT = − 20 lg ⎜10 20 + 10 20 ⎟ connectors ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ 308 NEXT local = NEXT remote = NEXTconnector (11) L 309 IL ≈α × (12) cable cable 100 m 100 310 where 311 NEXT local is the NEXT of the connector at the local end of the cord 312 NEXT remote is the NEXT of the connector at the remote end of the cord 313 IL cable is the insertion loss of the cable 314 IL connector is the insertion loss of the connector 315 NEXT connector is the NEXT of each connector as specified in Table 44, except for category 5 316 which is specified in equation 14. 317 α cable 100 m is the insertion loss of 100 m of the cable used for the cord 318 L is the length of the cable in the cord 319 NOTE All variables are expressed in dB, except “L”, expressed in meters 320 The length corrected near-end crosstalk of the cable of the cord is given by: ⎡ L ⎛ −α ⎞⎤ ×⎜ cable , 100 m ⎟ ⎢ ⎥ ⎢ 100 ⎜ 5 ⎟⎥ ⎝ ⎠ 321 NEXT = NEXT − 10 × lg ⎢1 − 10 ⎥ (13) cable, L cable, 100 m ⎢ ⎛ cable, 100 m ⎞ ⎥ − α ⎢ ⎜ ⎟ ⎥ ⎢ ⎜ 5 ⎟ ⎥ ⎢⎣ 1 − 10⎝ ⎠ ⎥ ⎦ 322 Calculations yielding NEXT limits in excess of 65 dB shall revert to a limit of 65 dB. Table 44 lists 323 informative values of NEXT at key frequencies for different length cords. These values are based on 324 the horizontal cable requirements that are consistent with clause 6 and IEC 61156-5 (insertion loss 325 derating of 50 %), as well as the connector performance requirements of clause 10. 326 Table 65 – Informative values of NEXT for balanced cords at key frequencies NEXT dB Frequency Category 5 Category 6 Category 6 A MHz Length Length Length 2m 5m 10 m 2m 5m 10 m 2m 5m 10 m 1 65,0 65,0 65,0 65,0 65,0 65,0 65,0 65,0 65,0 100 34,6 32,8 30,9 46,2 45 44,2 46,2 45,1 44,2 250 N/A 38,6 37,9 37,6 38,7 38,0 37,6 500 N/A 31,0 31,3 31,7 ISO/IEC JTC 1/SC 25N1318c.doc 18 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 19 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 327 For the commonly available Category 5 test head the NEXT is: 328 NEXT = 41, 0 -20lg(f/100) (14) connector 329 Table 66 – Informative values of NEXT for balanced cords at key frequencies NEXT dB Frequency Category 7 Category 7 A MHz Length Length 2m 5m 10 m 2m 5m 10 m 1 65,0 65,0 65,0 65,0 65,0 65,0 100 65,0 64,7 62,9 65 65,0 65 250 60,7 61,2 61,9 62,6 59,6 63,3 500 56,5 57,2 58,0 57,1 52,2 58,0 600 55,4 56,2 57,0 55,6 50,1 56,7 1000 N/A 47,4 43,9 48,9 ISO/IEC JTC 1/SC 25N1318c.doc 19 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 20 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 330 Pages 83 to 89 331 Annex A 332 A.1 No meaning inserted for automatic numbering only 333 A.2 No meaning inserted for automatic numbering only 334 A.2.1 General to A.2.5.2 Power sum ACR (PS ACR) 335 Replace tables A.1 through A.20 with the following: 336 Table A.1 – Return loss for permanent link or CP link Frequency Minimum return loss Class MHz dB C 1 ≤ f ≤ 16 15,0 1 ≤ f < 20 19,0 D 20 ≤ f ≤ 100 32 – 10 lg(f) 1 ≤ f < 10 21,0 E 10 ≤ f < 40 26 – 5 lg(f) 40 ≤ f < 250 34 – 10 lg(f) 1 ≤ f < 10 21,0 10 ≤ f < 40 26 – 5 lg(f) EA 40 ≤ f < 398,1 34 – 10 lg(f) 398,1 ≤ f ≤ 500 8,0 1 ≤ f < 10 21,0 10 ≤ f < 40 26 – 5 lg(f) F 40 ≤ f < 251,2 34 – 10 lg(f) 251,2 ≤ f ≤ 600 10,0 1 ≤ f < 10 21,0 10 ≤ f < 40 26 – 5 lg(f) FA 40 ≤ f < 251,2 34 – 10 lg(f) 251,2 ≤ f ≤ 631 10,0 631 ≤ f ≤ 1000 38 – 10 lg(f) ffs 337 ISO/IEC JTC 1/SC 25N1318c.doc 20 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 21 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 338 Table A.2 – Informative return loss values for permanent link with 339 maximum implementation at key frequencies Minimum return loss Frequency dB MHz Class C Class D Class E Class E A Class F Class F A 1 15,0 19,0 21,0 21,0 21,0 21,0 16 15,0 19,0 20,0 20,0 20,0 20,0 100 N/A 12,0 14,0 14,0 14,0 14,0 250 N/A N/A 10,0 10,0 10,0 10,0 500 N/A N/A N/A 8,0 10,0 10,0 ffs 600 N/A N/A N/A N/A 10,0 10,0 1000 N/A N/A N/A N/A N/A 8,0 ffs 340 Table A.3 – Insertion loss for permanent link or CP link a Class Frequency Maximum insertion loss MHz dB A f = 0,1 16,0 f = 0,1 5,5 B f =1 5,8 C 1 ≤ f ≤ 16 ( ) 0,9 × 3,23 f + 3 × 0,2 D 1 ≤ f ≤ 100 (L/100 ) × (1,910 8 f + 0,022 2 × f + 0,2 ) f + n × 0,04 × f E 1 ≤ f ≤ 250 (L/100 ) × (1,82 f + 0,0169 × f + 0,25 ) + n × 0,02 × f f EA 1 ≤ f ≤ 500 (L/100 ) × (1,82 f + 0,0091 × f + 0,25 f ) + n × 0,02 × f F 1 ≤ f ≤ 600 (L/100 ) × (1,8 f + 0,01 × f + 0,2 f ) + n × 0,02 × f FA 1 ≤ f ≤ 1000 (L/100 ) × (1,8 f + 0,005 × f + 0,25 f ) + n × 0,02 × f NOTE: L = L FC + L CP Y L FC = length of fixed cable (m) L CP = length of CP cord (where present) (m) Y = the ratio of CP cable attenuation (dB/m) to fixed horizontal cable attenuation (dB/m) (see 7.2.2.2) n = 2 for Configurations A, B and D (Editor’s note: change A,B, D to lower case(a,b,d) to agree with Figure 12 lettering) n = 3 for Configuration C (Editor’s note: change to lower case “c”. Also add “d” to agree with Figure 12) a Insertion loss ( IL ) at frequencies that correspond to calculated values of less than 4,0 dB shall revert to a maximum requirement of 4,0 dB. ISO/IEC JTC 1/SC 25N1318c.doc 21 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 22 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 341 Table A.4 – Informative insertion loss values for permanent link with 342 maximum implementation at key frequencies Maximum insertion loss Frequency dB MHz Class A Class B Class C Class D Class E Class E A Class F Class FA 0,1 16,0 5,5 N/A N/A N/A N/A N/A N/A 1 N/A 5,8 4,0 4,0 4,0 4,0 4,0 4,0 16 N/A N/A 12,2 7,7 7,1 7,0 6,9 6,8 100 N/A N/A N/A 20,4 18,5 17,8 17,7 17,3 250 N/A N/A N/A N/A 30,7 28,9 28,8 27,7 500 N/A N/A N/A N/A N/A 42,1 42,1 39,8 600 N/A N/A N/A N/A N/A N/A 46,6 43,9 1000 N/A N/A N/A N/A N/A N/A N/A 57,6 343 Table A.5 – NEXT for permanent link or CP link Class Frequency Minimum NEXT MHz dB A f = 0,1 27,0 B 0,1 ≤ f ≤ 1 25 - 15 lg( f) C 1 ≤ f ≤ 16 40,1 - 15,8 lg( f ) ⎛ 65,3 − 15 lg ( f) 83 − 20 lg ( f ) ⎞ ⎜ ⎟ D 1 ≤ f ≤ 100 − 20 lg ⎜ 10 − 20 + 10 − 20 ⎟ a ⎜ ⎟ ⎝ ⎠ ⎛ 74,3 − 15 lg ( f ) 94 − 20 lg ( f ) ⎞ ⎜ ⎟ E 1 ≤ f ≤ 250 − 20 lg ⎜ 10 − 20 + 10 − 20 ⎟ ⎜ ⎟ ⎝ ⎠ 1 ≤ f ≤ 250 − 20 lg(1,928 × 10 ^ −4 f 0,75 + 1,996 × 10 −5 f ) EA 250 ≤ f ≤ 500 − 20 lg(1,928 × 10 ^ −4 f 0,75 + 4,989 × 10 ^ −3 ( f / 250)1,5 ) ⎛ 102,4 − 15 lg ( f ) 102,4 − 15 lg ( f ) ⎞ ⎜ ⎟ F 1 ≤ f ≤ 600 − 20 lg ⎜ 10 − 20 + 10 − 20 ⎟ b ⎜ ⎟ ⎝ ⎠ 1 ≤ f ≤ 600 − 20 lg(5,37 × 10 ^ −6 f 0,75 + 1,531 × 10 ^ −6 f ) b FA 600 ≤ f ≤ 1000 − 20 lg(5,37 × 10 ^ −6 f 0,75 + 9,194 × 10 ^ −4 ( f / 250) 2 ) b ffs a NEXT at frequencies that correspond to calculated values of greater than 60,0 dB shall revert to a minimum requirement of 60,0 dB. b NEXT at frequencies that correspond to calculated values of greater than 65,0 dB shall revert to a minimum requirement of 65,0 dB. ISO/IEC JTC 1/SC 25N1318c.doc 22 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 23 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 344 Table A.6 – Informative NEXT values for permanent link with maximum implementation at key 345 frequencies Minimum NEXT Frequency dB MHz Class A Class B Class C Class D Class E Class E A Class F Class F A 0,1 27,0 40,0 N/A N/A N/A N/A N/A N/A 1 N/A 25,0 40,1 60,0 65,0 65 65,0 65,0 16 N/A N/A 21,1 45,2 54,6 54,6 65,0 65,0 100 N/A N/A N/A 32,3 41,8 41,8 65,0 65,0 250 N/A N/A N/A N/A 35,3 35,3 60,4 62,8 500 N/A N/A N/A N/A 30,4 29,2 55,9 57,5 600 N/A N/A N/A N/A N/A N/A 54,7 56,1 1000 N/A N/A N/A N/A N/A N/A N/A 49,1 ffs 346 Table A.7 – PS NEXT for permanent link or CP link Class Frequency Minimum PS NEXT MHz dB ⎛ 62,3 − 15 lg ( f ) 80 − 20 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ D 1 ≤ f ≤ 100 − 20 lg ⎜ 10 + 10 ⎟ a ⎜ ⎟ ⎝ ⎠ ⎛ 72,3 − 15 lg ( f ) 90 − 20 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ E 1 ≤ f ≤ 250 − 20 lg ⎜ 10 + 10 ⎟ b ⎜ ⎟ ⎝ ⎠ 1 ≤ f ≤ 250 − 20 lg(2,427 × 10 ^ −4 f 0,75 + 3,162 × 10 ^ −5 f ) b EA 250 ≤ f ≤ 500 − 20 lg(2,427 × 10 ^ −4 f 0,75 + 7,907 × 10 ^ −3 ( f / 250)1,5 ) ⎛ 99,4 − 15 lg ( f ) 99,4 − 15 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ F 1 ≤ f ≤ 600 − 20 lg ⎜ 10 + 10 ⎟ b ⎜ ⎟ ⎝ ⎠ 1 ≤ f ≤ 600 − 20 lg(7,586 × 10^ −6 f 0,75 + 2,163 × 10^ −6 f ) b FA 600 ≤ f ≤ 1 000 − 20 lg(7,586 × 10 ^ −6 f 0,75 + 1,299 × 10 ^ −3 ( f / 600) 2 ) ffs a PS NEXT at frequencies that correspond to calculated values of greater than 57,0 dB shall revert to a minimum requirement of 57,0 dB. b PS NEXT at frequencies that correspond to calculated values of greater than 62,0 dB shall revert to a minimum requirement of 62,0 dB. ISO/IEC JTC 1/SC 25N1318c.doc 23 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 24 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 347 Table A.8 – Informative PS NEXT values for permanent link with 348 maximum implementation at key frequencies Minimum PS NEXT Frequency dB MHz Class D Class E Class E A Class F Class F A 1 57,0 62,0 62,0 62,0 62,0 16 42,2 52,2 52,2 62,0 62,0 100 29,3 39,3 39,3 62,0 62,0 250 N/A 32,7 32,7 57,4 59,8 500 N/A N/A 26,4 52,9 54,5 600 N/A N/A N/A 51,7 53,1 1000 N/A N/A N/A N/A 46,1 ffs 349 Table A.9 – Informative ACR-N values for permanent link with 350 maximum implementation at key frequencies Minimum ACR-N Frequency dB MHz Class D Class E Class E A Class F Class F A 1 56,0 61,0 61 61,0 61,0 16 37,5 47,5 47.6 58,1 58,2 100 11,9 23,3 24,0 47,3 47,7 250 N/A 4,7 6,4 31,6 35,1 500 N/A N/A 12,9 13,8 17,7 600 N/A N/A N/A 8,1 12,2 1000 N/A N/A N/A N/A -,7ffs 351 Table A.10 – Informative PS ACR-N values for permanent link with 352 maximum implementation at key frequencies Minimum PS ACR-N Frequency dB MHz Class D Class E Class E A Class F Class F A 1 53,0 58,0 58,0 58,0 58,0 16 34,5 45,1 45,2 55,1 55,2 100 8,9 20,8 21,5 44,3 44,7 250 N/A 2,0 3,8 28,6 32,1 500 N/A N/A -15,7 10,8 14,7 600 N/A N/A N/A 5,1 9,2 1000 N/A N/A N/A N/A -11.5ffs 353 354 A.2.1 No meaning inserted for automatic numbering only 355 A.2.2 No meaning inserted for automatic numbering only 356 A.2.3 No meaning inserted for automatic numbering only 357 A.2.4 No meaning inserted for automatic numbering only 358 A.2.5 No meaning inserted for automatic numbering only 359 A.2.6 No meaning inserted for automatic numbering only ISO/IEC JTC 1/SC 25N1318c.doc 24 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 25 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 360 Page 90 361 A.2.6.1 Pair-to-pair ACR-F 362 Replace: 363 The ELFEXT of each pair combination of a permanent link or CP link shall meet the requirements 364 derived by the equation A.4. 365 The ELFEXT of each pair combination of a permanent link with maximum implementation is given in 366 Table A.12. 367 The ELFEXT shall be consistent with the cabling components used. 368 ELFEXT ik of pairs i and k is computed as follows: 369 ELFEXTik = FEXTik − ILk (A.4) 370 where 371 i is the number of the disturbed pair; 372 k is the number of the disturbing pair; 373 FEXT ik is the far end crosstalk loss coupled from pair i into pair k. When required, it shall be measured 374 according to IEC 61935-1: 375 IL k is the insertion loss of pair k. When required, it shall be measured according to IEC 61935-1. 376 NOTE The ratio of the insertion loss of the disturbed pair to the input-to-output FEXT is relevant for the signal-to-noise-ratio 377 consideration. The results computed according to the formal definition above cover all possible combinations of insertion loss of 378 wire pairs and corresponding input-to-output FEXT . 379 By: 380 The ACR-F of each pair combination of a permanent link or CP link shall meet the requirements derived 381 by the equation A.4. 382 The ACR-F of each pair combination of a permanent link with maximum implementation is given in 383 Table A.12. 384 ACR-F ik of pairs i and k is computed as follows: 385 ACR − F = FEXT − IL (A.4) ik ik k 386 where 387 i is the number of the disturbed pair; 388 k is the number of the disturbed; 389 FEXT ik is the far end crosstalk loss coupled from pair i into pair k. When required, it shall be measured 390 according to IEC 61935-1: 391 IL k is the insertion loss of pair k. When required, it shall be measured according to IEC 61935-1. 392 NOTE The ratio of the insertion loss of the disturbed pair to the input-to-output FEXT is relevant for the signal-to-noise-ratio 393 consideration. The results computed according to the formal definition above cover all possible combinations of insertion loss of 394 wire pairs and corresponding input-to-output FEXT . ISO/IEC JTC 1/SC 25N1318c.doc 25 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 26 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 395 Pages 90 to 95 396 A.2.6.1 Pair to pair ELFEXT 397 Replace tables A.11 through A.12 with the following: 398 Table A.11 – ACR-F for permanent link or CP link a Class Frequency Minimum ACR-F MHz dB ⎛ 63,8 − 20 lg ( f ) 75,1 − 20 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ D 1 ≤ f ≤ 100 − 20 lg ⎜ 10 + n × 10 ⎟ b ⎜ ⎟ ⎝ ⎠ ⎛ 67,8 − 20 lg ( f ) 83,1 − 20 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ E 1 ≤ f ≤ 250 − 20 lg ⎜ 10 + n × 10 ⎟ c ⎜ ⎟ ⎝ ⎠ 64,2-20lg(f) n=3 EA 1 ≤ f ≤ 500 65,2-20lg(f) n=2 c ⎛ 94 − 20 lg ( f ) 90 − 15 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ F 1 ≤ f ≤ 600 − 20 lg ⎜ 10 + n × 10 ⎟ c ⎜ ⎟ ⎝ ⎠ c 88,8-20lg(f) n=3 FA 1 ≤ f ≤ 1000 c 90,5-20lg(f) n=2 ffs NOTE n = 2 for Configurations A, B and D n = 3 for Configuration C a ACR-F at frequencies that correspond to measured FEXT values of greater than 70,0 dB are for information only. b ACR-F at frequencies that correspond to calculated values of greater than 60,0 dB shall revert to a minimum requirement of 60,0 dB. c ACR-F at frequencies that correspond to calculated values of greater than 65,0 dB shall revert to a minimum requirement of 65,0 dB. ISO/IEC JTC 1/SC 25N1318c.doc 26 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 27 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 399 Table A.12 – Informative ACR-F values for permanent link with 400 maximum implementation at key frequencies Minimum ACR-F dB Frequency MHz Class D Class E Class E A Class F Class F A 1 58,6 64,2 64,2 65,0 65,0 16 34,5 40,1 40,1 59,3 64,7 100 18,6 24,2 24,2 46,0 48,8 250 N/A 16,2 16,2 39,2 40,8 500 N/A N/A 10,2 34,0 34,8 600 N/A N/A N/A 32,6 33,2 1 000 N/A N/A N/A N/A 28,8 401 Pages 91 402 A.2.6.2 Power sum ELFEXT (PS ELFEXT) 403 Replace: 404 The PS ELFEXT of each pair of a permanent link or CP link shall meet the requirements derived by the 405 equation in A.5. 406 The PS ELFEXT of each pair of a permanent link with maximum implementation is given in Table A.14. 407 The PS ELFEXT shall be consistent with the cabling components used. 408 PS ELFEXT k of pair k is computed as follows: − ELFEXT ik n 409 PS ELFEXTk = −10 lg ∑ 10 10 (A.5) i = 1, i ≠ k 410 where 411 i is the number of the disturbing pair; 412 k is the number of the disturbed pair; 413 n is the total number of pairs; 414 ELFEXT ik is the equal level far end crosstalk loss coupled from pair i into pair k. 415 By: 416 The PS ACR-F of each pair of a permanent link or CP link shall meet the requirements derived by the 417 equation in A.5. 418 The PS ACR-F of each pair of a permanent link with maximum implementation is given in Table A.14. 419 PS ACR-F k of pair k is computed as follows: − ACR − F ik n 420 PS ACR − F = −10 lg k ∑ 10 10 (A.5) i = 1, i ≠ k ISO/IEC JTC 1/SC 25N1318c.doc 27 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 28 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 421 where 422 i is the number of the disturbing pair; 423 k is the number of the disturbed pair; 424 n is the total number of pairs; 425 ACR-F ik is the attenuation to crosstalk ratio at the far end coupled from pair i into pair k. 426 Pages 92 to 95 427 A.2.6.2 Power sum ELFEXT 428 Replace tables A.13 through A.16 with the following: 429 Table A.13 – PS ACR-F for permanent link or CP link a,b Class Frequency Minimum PS ELFEXT MHz dB ⎛ 60,8 − 20 lg ( f ) 72,1 − 20 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ D 1 ≤ f ≤ 100 − 20 lg ⎜ 10 + n × 10 ⎟ b ⎜ ⎟ ⎝ ⎠ ⎛ 64,8 − 20 lg ( f ) 80,1 − 20 lg ( f ) ⎞ ⎜ − 20 − 20 ⎟ E 1 ≤ f ≤ 250 − 20 lg ⎜ 10 + n × 10 ⎟ c ⎜ ⎟ ⎝ ⎠ 61,2-20lg(f) n=3 EA 1 ≤ f ≤ 500 62,2-20lg(f) n=2 c ⎛ 91 − 20 lg ( f ) 87 − 15 lg ( f ) ⎞ ⎜ ⎟ 1 ≤ f ≤ 600 − 20 lg ⎜ 10 − 20 + n × 10 − 20 c F ⎟ ⎜ ⎟ ⎝ ⎠ 1 ≤ f ≤ 1 000 85,8-20lg(f) n=3 FA 87,5-20lg(f) n=2 ffs NOTE n = 2 for configurations A, B and D n = 3 for configuration C a PS ACR-F at frequencies that correspond to measured PSFEXT values of greater than 70,0 dB are for information only. b PS ACR-F at frequencies that correspond to calculated values of greater than 57,0 dB shall revert to a minimum requirement of 57,0 dB. c PS ACR-F at frequencies that correspond to calculated values of greater than 62,0 dB shall revert to a minimum requirement of 62,0 dB. ISO/IEC JTC 1/SC 25N1318c.doc 28 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 29 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 430 Table A.14 – Informative PS ACR-F values for permanent link with maximum implementation at 431 key frequencies Minimum PS ELFEXT dB Frequency MHz Class D Class E Class E A Class F Class F A 1 55,6 61,2 61,2 62,0 62,0 16 31,5 37,1 37,1 56,3 61,7 100 15,6 21,2 21,2 43,0 45,8 250 N/A 13,2 13,2 36,2 37,8 500 N/A N/A 7,2 31,0 31,8 600 N/A N/A N/A 29,6 30,2 1 000 N/A N/A N/A N/A 25,8 432 Table A.15 – Direct current (d.c.) loop resistance for permanent link or CP link Class Maximum d.c. loop resistance Ω A 530 B 140 C 34 D, E, E A , F, F A ( L /100) × 22 + n × 0,4 Where L L FC + L CP × Y L FC length of fixed cable (m) L CP length of CP cord (where present) (m) Y the ratio of CP cable attenuation (dB/m) to fixed horizontal cable attenuation (dB/m) per Table 31 of 7.2.2.2.) n 2 for Configurations A, B and D n 3 for Configuration C 433 Table A.16 – Informative d.c. loop resistance for permanent link with 434 maximum implementation Maximum d.c. loop resistance Ω Class A Class B Class C Class D Class E & Class F & EA FA 530 140 34 21 21 21 435 A.2.7 No meaning inserted for automatic numbering only 436 A.2.8 No meaning inserted for automatic numbering only 437 Page 93 438 A.2.9 Propagation delay 439 Delete 4 th paragraph: 440 The propagation delay shall be consistent with the cabling components used. ISO/IEC JTC 1/SC 25N1318c.doc 29 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 30 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 441 Pages 94 to 95 442 A.2.9 Propagation delay 443 Replace tables A.17 through A.18 with the following: 444 Table A.17 – Propagation delay for permanent link or CP link Class Frequency Maximum propagation delay MHz µs A f = 0,1 19,400 B 0,1 ≤ f ≤ 1 4,400 C 1 ≤ f ≤ 16 (L/100 ) × (0,534 + 0,036 ) f + n × 0,002 5 D 1 ≤ f ≤ 100 (L/100 ) × (0,534 + 0,036 f ) + n × 0,002 5 E 1 ≤ f ≤ 250 (L/100 ) × (0,534 + 0,036 f ) + n × 0,002 5 EA 1 ≤ f ≤ 500 (L/100 ) × (0,534 + 0,036 f ) + n × 0,002 5 F 1 ≤ f ≤ 600 (L/100 ) × (0,534 + 0,036 f ) + n × 0,002 5 FA 1 ≤ f ≤ 1 000 (L/100 ) × (0,534 + 0,036 f ) + n × 0,002 5 Where L L FC + L CP L FC length of fixed cable (m) L CP length of CP cord (where present) (m) n 2 for configurations A, B and D n 3 for configuration C 445 Table A.18 – Informative propagation delay values for permanent link with 446 maximum implementation at key frequencies Maximum propagation delay Frequency µs MHz Class A Class B Class C Class D Class E Class E A Class F Class F A 0,1 19,400 4,400 N/A N/A N/A N/A N/A N/A 1 N/A 4,400 0,521 0,521 0,521 0,521 0,521 0,521 16 N/A N/A 0,496 0,496 0,496 0,496 0,496 0,496 100 N/A N/A N/A 0,491 0,491 0,491 0,491 0,491 250 N/A N/A N/A N/A 0,490 0,490 0,490 0,490 500 N/A N/A N/A N/A N/A 0,490 0,490 0,490 600 N/A N/A N/A N/A N/A N/A 0,489 0,489 1 000 N/A N/A N/A N/A N/A N/A N/A 0,489 447 Page 94 448 A.2.10 Delay skew 449 Delete: 450 The delay skew shall be consistent with the cabling components used. ISO/IEC JTC 1/SC 25N1318c.doc 30 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 31 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 451 Pages 95 452 A.2.10 Delay skew 453 Replace tables A.19 and A.20 with the following: 454 Table A.19 – Delay skew for permanent link or CP link Class Frequency Maximum delay skew MHz µs A f = 0,1 N/A B 0,1 ≤ f ≤ 1 N/A C 1 ≤ f ≤ 16 (L/100 ) × 0,045 + n × 0,001 25 D 1 ≤ f ≤ 100 (L/100 ) × 0,045 + n × 0,001 25 E 1 ≤ f ≤ 250 (L/100 ) × 0,045 + n × 0,001 25 EA 1 ≤ f ≤ 500 (L/100 ) × 0,045 + n × 0,001 25 F 1 ≤ f ≤ 600 (L/100 ) × 0,025 + n × 0,001 25 FA 1 ≤ f ≤ 1000 (L/100 ) × 0,025 + n × 0,001 25 NOTE L L FC + L CP L FC length of fixed cable (m) L CP length of CP cord (where present) (m) n 2 for configurations A, B and D n 3 for configuration C 455 Table A.20 – Informative delay skew for permanent link with maximum implementation Class Frequency Maximum delay skew MHz µs A f = 0,1 N/A B 0,1 ≤ f ≤ 1 N/A a C 1 ≤ f ≤ 16 0,044 a D 1 ≤ f ≤ 100 0,044 a E 1 ≤ f ≤ 250 0,044 a EA 1 ≤ f ≤ 500 0,044 b F 1 ≤ f ≤ 600 0,026 b FA 1 ≤ f ≤ 1000 0,026 a This is the result of the calculation 0,9*0,045+3 × 0,001 25. b This is the result of the calculation 0,9*0,025+3 × 0,001 25. ISO/IEC JTC 1/SC 25N1318c.doc 31 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 32 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 456 Page 95 457 Add the following after A.2.10 Delay skew: 458 A.2.11 Alien crosstalk 459 A.2.11.1 General 460 The following alien crosstalk requirements are applicable only to Classes E A and F A . Alien crosstalk of 461 Class F is considered to be as good as the alien crosstalk performance specified for Class E A . For 462 information on alien crosstalk performance of Class E systems, see ISO/IEC TR 24750. 463 If coupling attenuation for Class E A or F channels is 10 dB better than Table 22 or for Class F A channels 464 is 25 dB better than Table 22, then PS ANEXT and PS AACR–F are met by design. 465 A.2.11.2 Power sum alien NEXT (PS ANEXT) 466 The PS ANEXT of each pair of a link shall meet the requirements derived by the equation in Table A.21. 467 The PS ANEXT requirements shall be met at both ends of the cabling. 468 PS ANEXT k of pair k is computed as follows: ⎡ − ANEXT l , i, k ⎤ ⎢ N n ⎥ 10 469 PS ANEXT = −10 lg⎢ ∑ ∑ 10 ⎥ (A.7) k ⎢l = 1 i = 1 ⎥ ⎢ ⎥ ⎣ ⎦ 470 where 471 k is the number of the disturbed pair in the disturbed link; 472 i is the number of the disturbing pair in a disturbing link l; 473 l is the number of the disturbing link; 474 N is the total number of disturbing link; 475 n is the number of disturbing pairs in disturbing link l; 476 ANEXT l,i,k is the alien near end crosstalk loss coupled from pairs i of disturbing link (l) to the pair k of 477 the disturbed link. ISO/IEC JTC 1/SC 25N1318c.doc 32 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 33 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 478 Table A.21 – PS ANEXT for link Frequency Minimum PS ANEXT a Class MHz dB 1 ≤ f < 100 80 − 10lg ( f ) EA b 100 ≤ f ≤ 500 90 − 15lg ( f ) 1 ≤ f < 100 95 − 10lg ( f ) FA 100 ≤ f ≤ 1 000 105 − 15lg ( f ) a PS ANEXT at frequencies that correspond to calculated values of greater than 67,0 dB shall revert to a minimum requirement of 67,0 dB. b If the average insertion loss of the disturbed pairs at 100 MHz, IL 100MHz , avg is less than 7 dB, then the PSANEXT loss shall be the greater of the two values: 7 − IL ⎫ f − 100 100 MHz, avg ⎪ PS ANEXT = 60 − 7 ⋅ ⋅ 400 IL ⎪ 100 MHz, avg ⎬ for f ≥ 100 MHz ⎛ f − 100 ⎞ ⎪ PS ANEXT = ⎜ 60 − 6 ⋅ ⎟ − 15 lg( f / 100) ⎪ ⎝ 400 ⎠ ⎭ where: f is the frequency in MHz 1 4 IL = ∑ IL 100 MHz , avg 4 i =1 100 MHz , i and IL 100 MHz , avg is the insertion loss of a wire pair i at 100 MHz. 479 Secretary’s Note to tables A.21 and A.23 480 After the WG 3 had approved the above “get out note a” to Table A.21 and table 23 by a great majority it 481 was suggested that the term -15lg (f/100) was missing. The secretary did not accept the document to be 482 distributed with an equation that differed from the one approved by the WG. In order not to delay the 483 development of the document an additional question has been added to the voting form. 484 Equations voted on 7 − IL ⎫ f − 100 100 MHz, avg ⎪ PS ANEXT = 60 − 7 ⋅ ⋅ 485 400 IL ⎪⎪ 100 MHz, avg ⎬ for f ≥ 100 MHz ⎛ f − 100 ⎞ ⎪ PS ANEXT = ⎜ 60 − 6 ⋅ ⎟ ⎪ ⎝ 400 ⎠ ⎪⎭ 486 Equations including an extra term ⎛ 7 − IL ⎞⎫ ⎜ f − 100 100 MHz , avg ⎟⎪ 487 PS ANEXT = 60 − 15 lg( f / 100 ) − ⎜ 7 ⋅ ⋅ ⎟⎪ ⎜ 400 IL ⎟⎪ ⎝ 100 MHz , avg ⎠⎬ for f ≥ 100 MHz ⎛ ⎛ f − 100 ⎞ ⎞ ⎪ PS ANEXT = ⎜⎜ 60 − 15 lg( f / 100 ) − ⎜ 6 ⋅ ⎟⎟ ⎪ ⎝ ⎝ 400 ⎠ ⎟⎠ ⎭⎪ 488 End of Secretary’s note ISO/IEC JTC 1/SC 25N1318c.doc 33 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 34 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 489 Table A.22 – Informative PS ANEXT values for link at key frequencies Minimum PS ANEXT Frequency dB MHz Class E A Class F A 1 67,0 67,0 100 60,0 67,0 250 54,0 67,0 500 49,5 49,5 1 000 N/A 45,0 490 491 The PS ANEXTavg of each link shall meet the requirements derived by the equations in Table A.23. 492 The PS ANEXT avg requirements shall be met at both ends of the cabling. 493 PS ANEXT avg is computed as follows: 1⎡ n ⎤ 494 PS ANEXTavg = ⎢ ∑ PS ANEXTk ⎥ (A.8) n ⎢⎣k = 1 ⎥⎦ 495 where 496 k is the number of the disturbed pair in the disturbed link; 497 n is the number of pairs in the disturbed link. 498 Table A.23 – PS ANEXT avg for link Frequency Minimum PS ANEXT avg a, b Class MHz dB 1 ≤ f < 100 82,25 − 10lg ( f ) EA 100 ≤ f ≤ 500 92,25 − 15lg ( f ) c a PS ANEXT avg for Class F A links is covered by Table A.21. b PS ANEXT at frequencies that correspond to calculated values of greater than 67,0 dB shall revert to a minimum requirement of 67,0 dB. c If the average insertion loss of the disturbed wire pairs at 100 MHz IL 100MHz , avg is less than 7 dB, then the PSANEXT loss shall be the greater of the two values: 7 − IL f − 100 100MHz, avg ⎫⎪ PSANEXT = 62,25 − 7 ⋅ ⋅ 400 IL ⎪ 100 MHz, avg ⎬ for f ≥ 100 MHz ⎛ f − 100 ⎞ ⎪ PSANEXT = ⎜ 62,25 − 6 ⋅ ⎟ − 15 Log ( f / 100) ⎪ ⎝ 400 ⎠ ⎭ where: f is the frequency in MHz 1 4 IL = ∑ IL 100 MHz , avg 4 i =1 100 MHz , i and IL 100 MHz , avg is the insertion loss of a pair i at 100 MHz. ISO/IEC JTC 1/SC 25N1318c.doc 34 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 35 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 499 Secretary’s Note to tables A.21 and A.23 500 After the WG 3 had approved the above “get out note b” to Table A.21 and table 23 by a great majority it 501 was suggested that the term -15lg (f/100) was missing. The secretary did not accept the document to be 502 distributed with an equation that differed from the one approved by the WG. In order not to delay the 503 development of the document an additional question has been added to the voting form. 504 Equations voted on 7 − IL ⎫ f − 100 100 MHz, avg ⎪ PS ANEXT = 60 − 7 ⋅ ⋅ 505 400 IL 100 MHz, avg ⎪⎪ ⎬ for f ≥ 100 MHz ⎛ f − 100 ⎞ ⎪ PS ANEXT = ⎜ 60 − 6 ⋅ ⎟ ⎪ ⎝ 400 ⎠ ⎭⎪ 506 Equations including an extra term ⎛ 7 − IL ⎞⎫ ⎜ f − 100 100 MHz , avg ⎟⎪ 507 PS ANEXT = 60 − 15 lg( f / 100 ) − ⎜ 7 ⋅ ⋅ ⎟⎪ ⎜ 400 IL ⎟⎪ ⎝ 100 MHz , avg ⎠⎬ for f ≥ 100 MHz ⎛ ⎛ f − 100 ⎞ ⎞ ⎪ PS ANEXT = ⎜⎜ 60 − 15 lg( f / 100 ) − ⎜ 6 ⋅ ⎟⎟ ⎪ ⎝ ⎝ 400 ⎠ ⎟⎠ ⎪⎭ 508 End of Secretary’s note 509 Table A.24 – Informative PS ANEXT avg values for link at key frequencies Minimum Frequency Class E A MHz PS ANEXT avg dB 1 67,0 100 62,3 250 56,3 500 51,8 510 A.2.11.3 Power sum alien ACR-F (PS AACR-F) for permanent link 511 A.2.11.3.1 General 512 The PS AACR-F of each pair of a link shall meet the requirements derived by the equation in Table 513 A.25. 514 The PS AACR-F shall be met at both ends of the cabling. 515 The PS AACR-F is computed based on AFEXT, and insertion losses of disturbing and disturbed links. 516 A.2.11.3.2 Links Class E A 517 The PS AFEXT for Class E A is computed as follows: ISO/IEC JTC 1/SC 25N1318c.doc 35 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 36 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 518 AFEXT norm is computed from Equations A.9 to A.12 as follows 519 If 520 IL − IL > 0 (A.9) k l, i 521 then ⎛ IL ⎞ ⎜ ⎟ 522 AFEXTnorm l,i,k = AFEXT − IL + IL − 10 lg⎜ k ⎟⎟ (A.10) l,i,k l, i k ⎜ ILl , i ⎝ ⎠ 523 The measured pair-to-pair alien FEXT values of a wire pair k in a disturbed link from the disturbing link l 524 are normalized by the difference of the insertion losses of disturbing and disturbed link. 525 If 526 IL − IL ≤ 0 (A.11) k l, i 527 then 528 AFEXTnorm l,i,k = AFEXT (A.12) l,i,k 529 where 530 k is the number of the disturbed pair in the disturbed link; 531 i is the number of the disturbing pair in a disturbing link l; 532 l is the number of the disturbing link; 533 AFEXT l,i,k is the alien far end crosstalk loss coupled from pairs i into pair k. 534 IL k is the measured insertion loss of pair k in the disturbed link. 535 IL l,i is the measured insertion loss of pair i of disturbing link l. 536 The PS AFEXT is determined according to Equation A.13. ⎛ ⎜ N ( − AFEXTnorm l , i, k ) ⎞⎟ n 537 PS AFEXT = −10 lg⎜ ∑ ∑ 10 10 ⎟ (A.13) k ⎜ ⎟ ⎜l = 1 i = 1 ⎟ ⎝ ⎠ 538 where: 539 N is the total number of disturbing links; 540 n is the number of disturbing pairs in disturbing link l; 541 k is the number of the disturbed pair in the disturbed link; 542 i is the number of the disturbing pair in a disturbing link l; 543 l is the number of the disturbing link; 544 The PS AACR-F k of disturbed pair k is determined according to Equation A.14. 545 A.2.11.3.3 Links Class F A 546 The PS AACR-F for Class F A is computed as follows: 547 The PS AFEXT is determined according to Equation A.14. ISO/IEC JTC 1/SC 25N1318c.doc 36 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 37 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 ⎛ − ⎛⎜ AFEXT ⎞⎟ ⎞⎟ ⎜ i, k ⎠ ⎜ N ⎝ ⎟ n 548 ⎜ PS AFEXT = −10 lg ∑ ∑ 10 10 ⎟ (A.14) k ⎜l = 1 i = 1 ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ 549 where: 550 N is the total number of disturbing links; 551 n is the number of disturbing pairs in disturbing link l; 552 k is the number of the disturbed pair in the disturbed link; 553 i is the number of the disturbing pair in a disturbing link l; 554 l is the number of the disturbing link; 555 The PS AACR-F k of disturbed pair k is determined according to Equation A.15. 556 PS AACR-F = PS AFEXT − IL (A.15) k k k 557 A.2.11.3.4 Power sum alien ACR-F (PS AACR-F) for links E A and F A 558 Table A.25 – PS AACR-F for link Class Frequency Minimum PS AACR-F a MHz dB EA 1 ≤ f ≤ 500 77 − 20lg ( f ) FA 1 ≤ f ≤ 1 000 92 − 20lg ( f ) a PS AACR–F at frequencies that correspond to calculated PS AFEXT values of greater than 67,0 dB or 102-15*lg(f) dB shall be for information only. 559 Table A.26– Informative PS AACR-F values for link at key frequencies Minimum PS AACR-F Frequency dB MHz Class E A Class F A 1 67,0 67,0 100 37,0 52,0 250 29,0 44,0 500 23,0 38,0 1 000 N/A 32,0 560 561 The PS AACR-F avg of each link shall meet the requirements derived by the equations in Table A.27. 562 The PS AACR-F avg requirements shall be met at both ends of the cabling. 563 PS AACR-F avg is computed as follows: 1⎡ n ⎤ 564 PS AACR-Favg = ⎢ ∑ PS AACR-Fk ⎥ (A.16) n ⎢⎣k = 1 ⎥⎦ 565 where 566 k is the number of the disturbed pair in the disturbed link; 567 n is the number of pairs in the disturbed link. ISO/IEC JTC 1/SC 25N1318c.doc 37 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 38 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 568 Table A.27 – PS AACR-F avg for link Class Frequency Minimum PS AACR-F avg a, b MHz dB EA 1 ≤ f ≤ 500 81 − 20lg ( f ) a PS AACR–F avg at frequencies that correspond to calculated PS AFEXT avg values of greater than 67,0 dB or 102-15*lg(f) dB (f.f.s.) shall be for information only. b PS AACR–F avg for Class F A channels is covered by Table 25 . 569 Table A.28– Informative PS AACR-F avg values for link at key frequencies Frequency Minimum Class E A PS AACR-F avg MHz dB 1 67,0 100 41,0 250 33,0 500 27,0 ISO/IEC JTC 1/SC 25N1318c.doc 38 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 39 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 570 Annex B 571 Page 97 572 B.2.3 Channel and link test schedules 573 Replace Table B.1 with the following: 574 Table B.1 - Cabling characteristics of balanced and optical fibre cabling for acceptance, 575 compliance and reference testing Characteristics of Testing for copper cabling Acceptance Compliance Reference Return loss I N N Insertion loss I N N NEXT I N N PS NEXT C C C ACR I N N PS ACR I C C ELFEXT I N N PS ELFEXT C C C DC loop resistance I N N Propagation delay I N N Delay Skew I N N Unbalance attenuation, near end (TCL) N Unbalance attenuation, far end (EL N TCTL) Coupling attenuation f.f.s. PS ANEXT N PS AACR-F N Length a I I N Wiremap N N N Continuity of conductors, screens (if N N N applicable), short and open circuits a Length is not a pass/fail criterion 576 Characteristics of Testing for optical fibre cabling Acceptance Compliance Reference Optical attenuation N N N Multimode modal bandwidth N Propagation delay I N N Length C C C Continuity and maintenance of polarity N N N ISO/IEC JTC 1/SC 25N1318c.doc 39 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 40 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 577 Annex C 578 Pages 99 to 103 579 Replace Annex C with the following: 580 C.1 Introduction 581 The mechanical and environmental performance of connecting hardware is vital to the cabling system. 582 Changes in contact resistance because of operational and environmental stress can negatively affect 583 the transmission characteristics of the cabling system. Product acceptance testing is accomplished by 584 subjecting the product to a number of mechanical and environmental conditions and measuring any 585 resistance deviations at prescribed intervals and after completion of each conditioning sequence. In 586 addition, the product shall not show evidence of degradation with respect to the ease of mechanical 587 termination, safety or other functional attributes at any time during or after environmental conditioning. 588 Connecting hardware often contains a combination of solderless connections and a separable contact 589 interface (jack/plug interface). All connections shall be tested. Each connection that comprises the 590 connecting hardware may be isolated and tested independently or all connections may be tested as an 591 assembly. When tested as an assembly, the total combined change in contact resistance may be used 592 to determine pass and fail criteria in place of isolating individual effects of the various connections. If 593 this method is employed, care should be taken to ensure the use of the most stringent test schedule as 594 the test schedules vary by type of connection. 595 NOTE 1 This annex provides mechanical connection performance requirements for connections that are not covered by a 596 specific IEC connector standard. It is intended to replace the specifications in this annex by reference to international 597 standards, as they become available. 598 NOTE 2 Connection interfaces that conform to the mechanical and environmental performance requirements of IEC 60603-7 599 (unscreened) or IEC 60603-7-1 (screened) comply with this annex as these documents speciy appropriate tests. Connection 600 interfaces that are covered by international standards other than the IEC 60603-7 series shall comply with at least the 601 equivalent mechanical and environmental performance requirements specified in this annex. 602 C.2 Solderless connections To ensure reliable solderless terminations of balanced twisted pair cable insulated conductors, and to ensure reliable solderless connections between component parts within connecting hardware, solderless connections shall meet the requirements of the applicable standards specified in table C.1. 603 Table C. 1 – Standards for solderless connections Connection type Standard Crimped connection IEC 60352-2 Accessible IDC IEC 60352-3 Non-accessible IDC IEC 60352-4 Press-in connection IEC 60352-5 IPC IEC 60352-6 604 The default criteria and conditions in the relevant standards in table 1 apply, except as specified in the 605 remainder of this clause. 606 The maximum initial contact resistance for an insulation displacement connection shall be 2,5 mΩ and 607 the maximum change in contact resistance during and after conditioning shall be 5 mΩ from the initial 608 value. ISO/IEC JTC 1/SC 25N1318c.doc 40 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 41 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 609 The following test conditions are specified, as detailed by the type test requirements of IEC 60352 610 series of standards. 611 • Vibration test severity: 10 Hz to 500 Hz. 612 • Low temperature (LCT): -40 °C. 613 • Electrical load and temperature, test current: 1 A dc. 614 C.3 Modular plugs and jacks 615 Fixed and free connectors (plugs and jacks) shall comply with the reliability requirements of the 616 applicable standard specified in table C.2. 617 Table C. 2 – Standards for modular plugs and jacks Category and type Standard Category 3, UTP IEC 60603-7 Category 3, ScTP IEC 60603-7-1 Category 5e, UTP IEC 60603-7-2 Category 5e, ScTP IEC 60603-7-3 Category 6, UTP IEC 60603-7-4 Category 6, ScTP IEC 60603-7-5 Category 6A, UTP IEC 60603-7-41 Category 6A, ScTP IEC 60603-7-51 Category 7, ScTP IEC 60603-7-7, Category 7A, ScTP IEC 60603-7-71, IEC 61076-3-104 618 The default criteria and conditions in the relevant standards in Table C. 2 apply, except as specified in 619 the remainder of this clause. 620 The number of conductor re-terminations per solderless connection shall comply with the specifications 621 in Table C. 3. Table C. 3 – Fixed and free connectors ( plugs and jacks) operations matrix Connecting hardware type Insertion and withdrawal, and conductor re- Minimum number of a termination, operations operations Modular plug Insertion / withdrawal with modular jack 750 Cable re-termination 0 Modular jack Insertion / withdrawal with modular plug 750 1) Cable re-termination 20 a Unless not intended for re-termination, in which case this value equals 0. 622 Between terminations, the solderless connection should be inspected for debris and extraneous material 623 should be removed. 624 C.4 Other connecting hardware 625 Examples of other connecting hardware include: 626 • cross-connect blocks and plugs 627 • pin and socket connectors ISO/IEC JTC 1/SC 25N1318c.doc 41 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 42 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 628 The reliability of connecting hardware, other than modular plugs and jacks shall be demonstrated by 629 complying with the applicable requirements of the standards specified in table C.4. The connecting 630 hardware shall be terminated, mounted, and operated in accordance with the manufacturer’s 631 instructions for use. A minimum of 100 individual electrical contact paths (e.g. connecting hardware, 632 input to output) shall be tested without failure. 633 The following tests shall be as per the manufacturer’s specification: 634 • Examination of dimensions and mass 635 • Insertion and withdrawal force requirements 636 • Effectiveness of any connector coupling device requirements 637 • Gauging and gauging continuity requirements 638 • Arrangement for contact resistance test 639 • Arrangement for vibration (dynamic stress) test Table C. 4 – Standards for other connecting hardware Category and type Standard a Category 3, UTP IEC 60603-7 Clause 6 and Clause 7 Category 3, ScTP IEC 60603-7-1 Category 5e, UTP IEC 60603-7-2 Category 5e, ScTP IEC 60603-7-3 Category 6, UTP IEC 60603-7-4 Category 6, ScTP IEC 60603-7-5 Category 6A, UTP IEC 60603-7-5 Category 6A, ScTP IEC 60603-7-5 Category 7 ScTP IEC 60603-7-7 Category 7A, ScTP IEC 60603-7-71, IEC 61076-3-104 a Excluding sub-clauses addressing pin and pair grouping assignment, creepage and clearance distances, transmission characteristics, transfer impedance, and test group EP (transmission testing). 640 The default criteria and conditions in the relevant standards in Table C. 4 apply, unless otherwise 641 specified in this clause. 642 The number of conductor re-terminations per solderless connection shall comply with the specifications 643 in Table C. 5. 644 Table C. 5 – Other connecting hardware operations matrix Connecting hardware type Insertion and withdrawal, and conductor re- Minimum number of a termination, operations operations Other connecting hardware “plug” Insertion / withdrawal operations with “jack” 200 Cable re-termination 0 Other connecting hardware “jack” Insertion / withdrawal operations with “plug” 200 1) Cable re-termination 20 Jumper re-termination 200 a Unless not intended for re-termination, in which case this value equals 0. 645 Between terminations, the solderless connection should be inspected for debris and extraneous material 646 should be removed. ISO/IEC JTC 1/SC 25N1318c.doc 42 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 43 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 647 Annex D Only for automatic numbring 648 Page 105 649 Annex E Acronyms for balanced cables 650 651 Replace Figure E.1 example text below: 652 653 For example: 654 SF/UTP = overall braid and foil screened cable with unscreened balanced elements 655 S/FTP = overall braid screened cable with foil screened balanced elements 656 657 658 By: 659 660 For example: 661 SF/UTP = overall braid and foil screened cable with unscreened balanced elements 662 S/FTP = overall braid screened cable with foil screened balanced elements 663 664 U/UTP = unscreened cable with unscreened balanced elements ISO/IEC JTC 1/SC 25N1318c.doc 43 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 44 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 665 Page 106 666 Replace Figure E.2 by the following: 667 668 669 U/UTP: U/UTP: 670 671 Cable sheath Cable sheath 672 Pair Quad 673 Conductor Pair / side circuit 674 675 Conductor 676 677 678 F/UTP: 679 680 681 Cable sheath 682 Foil screen 683 Pair 684 685 Conductor 686 U/FTP: 687 688 Cable sheath 689 U/FTP: Foil quad screen 690 Quad 691 Cable sheath Pair / side circuit 692 Foil pair screen 693 Pair Conductor 694 695 Conductor 696 697 698 699 SF/UTP: 700 Cable sheath 701 Braid screen 702 703 Foil screen 704 Pair 705 706 Conductor 707 708 709 S/FTP: 710 S/FTP: 711 Cable sheath 712 Braid screen 713 Cable sheath Braid screen Foil quad screen 714 715 Foil pair screen Quad 716 Pair Pair / side circuit Conductor Conductor 717 NOTE Sometimes the letter P in the abbreviation is replaced by Q to characterise a quad construction. 718 Figure E.1 – Cable naming schema ISO/IEC JTC 1/SC 25N1318c.doc 44 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 45 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 719 720 Annex F 721 Page 108 and 109 722 F.1 Supported applications for balanced cabling 723 Replace tables F.1 and F.2 with the following: 724 Table F.1 – Applications using balanced cabling Application Specification reference Date Additional name Class A (defined up to 100 kHz) PBX National requirements X.21 ITU-T Rec. X.21 1996 V.11 ITU-T Rec. X.21 1994 Class B (defined up to 1 MHz) S0-Bus (extended) ITU-T Rec. I.430 1993 ISDN Basic Access (Physical Layer) S0 Point-to-Point ITU-T Rec. I.430 1993 ISD2 Basic Access (Physical Layer) S1/S2 ITU-T Rec. I.431 1993 ISDN Primary Access (Physical Layer) CSMA/CD 1BASE5 ISO/IEC 8802-3 2000 Starlan Class C (defined up to 16 MHz) CSMA/CD 10BASE-T ISO/IEC 8802-3 2000 CSMA/CD 100BASE-T4 ISO/IEC 8802-3 2000 Fast Ethernet CSMA/CD 100BASE-T2 ISO/IEC 8802-3 2000 Fast Ethernet Token Ring 4 Mbit/s ISO/IEC 8802-5 1998 ISLAN ISO/IEC 8802-9 1996 Integrated Services LAN TM Demand priority ISO/IEC 8802-12 1998 VGAnyLAN ATM LAN 25,60 Mbit/s ATM Forum af-phy-0040.000 1995 ATM-25/Category 3 ATM LAN 51,84 Mbit/s ATM Forum af-phy-0018.000 1994 ATM-52/Category 3 ATM LAN 155,52 Mbit/s ATM Forum af-phy-0047.000 1995 ATM-155/Category 3 Class D 1995 (defined up to 100 MHz) Token Ring 16 Mbit/s ISO/IEC 8802-5 1998 ATM LAN 155.52 Mbit/s ATM Forum af-phy-0015.000 1994 ATM-155/Category 5 CSMA/CD 100BASE-TX ISO/IEC 8802-3 2000 Fast Ethernet Token Ring 100 Mbit/s ISO/IEC 8802-5 2001 TP-PMD ISO/IEC FCD 9314-10 2000 Twisted-Pair Physical Medium Dependent Class D 2002 (defined up to 100 MHz) CSMA/CD 1000BASE-T ISO/IEC 8802-3 2000 Gigabit Ethernet Firewire 100 Mbit/s IEEE 1394b 1999 Firewire/Category 5 Class E 2002 (defined up to 250 MHz) ATM LAN 1.2 Gbit/s ATM Forum af-phy-0162.000 2001 ATM-1200/Category 6 a CSMA/CD 10GBASE-T ISO/IEC 8802-3 2006 10Gigabit Ethernet Class E A 200x (defined up to 500 MHz) ATM LAN 1.2 Gbit/s ATM Forum af-phy-0162.000 2001 ATM-1200/Category 6 ISO/IEC JTC 1/SC 25N1318c.doc 45 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 46 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 CSMA/CD 10GBASE-T ISO/IEC 8802-3 200x 10Gigabit Ethernet Class F 2002 (defined up to 600 MHz) ATM LAN 1.2 Gbit/s ISOIEC? Forum af-phy-xxxx.000 2001 ATM-1200/?? CSMA/CD 10GBASE-T ISO/IEC 8802-3 200x 10 Gigabit Ethernet FC-100-DF-EL-S ISO/IEC 14165-114 2005 FA – FC-100-DF-EL-S Class F A 200x (defined up to 1 000 MHz) ATM LAN 1.2 Gbit/s ISOIEC? Forum af-phy-xxxx.000 2001 ATM-1200/?? CSMA/CD 10GBASE-T ISO/IEC 8802-3 2006 10 Gigabit Ethernet FC-100-DF-EL-S ISO/IEC 14165-114 2005 FA – FC-100-DF-EL-S a The minimum performance of class E channels does not support 10GBASE-T these channels will support 10GBASE-T provided they meet the requirements specified in ISO/IEC TR-24750. Such support may be limited to channels shorter than 100 m. Class E A or better is recommended for new installations. Applications supported by a given class are also supported by higher classes. Some applications may run on a lower class in cases where the specififc channel in question meets the performance criteria of the application. 725 Table F.2 – Modular connector pin assignment for applications Application Pins 1 & 2 Pins 3 & 6 Pins 4 & 5 Pins 7 & 8 PBX Class A a Class A a Class A Class A a X.21 Class A Class A V.11 Class A Class A b b S0-Bus (extended) Class B Class B b b S0 Point-to-Point Class B Class B c b S1/S2 Class B Class B CSMA/CD 1BASE5 Class B Class B CSMA/CD 10BASE-T Class C Class C Token Ring 4 Mbit/s Class C Class C b ISLAN Class C Class C Demand Priority Class C Class C Class C Class C ATM-25 Category 3 Class C Class C ATM-51 Category 3 Class C Class C ATM -155 Category 3 Class C Class C Token Ring 16 Mbit/s Class D Class D TP-PMD Class D Class D ATM-155 Category 5 Class D Class D CSMA/CD 100BASE-T4 Class C Class C Class C Class C CSMA/CD 100BASE-T2 Class C Class C CSMA/CD 100BASE-TX Class D Class D Token Ring 100 Mbit/s Class D Class D CSMA/CD 1000BASE-T Class D Class D Class D Class D ATM-1200 Category 6 Class E Class E Class E Class E CSMA/CD 10GBASE-T Class E Class E Class E Class E FC-100-DF-EL-S d Class F Class F a Option dependent on supplier. b Optional power sources. c Option for continuity of cable screen. d Option outside TO as ISO/IEC 14165-114 specifies IEC 61076-3-104. ISO/IEC JTC 1/SC 25N1318c.doc 46 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 47 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 726 Page 110 727 F.2 Supported applications for optical fibre cabling 728 Replace table F.3 column headings to read: Network application Max. channel insertion loss (dB) ISO/IEC 11801 channel supported on 729 Page 123 730 Annex G Channel and permanent link models for balanced cabling 731 . 732 Add to Annex G the following clauses 733 G.1 No meaning inserted for automatic numbering only 734 G.2 No meaning inserted for automatic numbering only 735 G.3 No meaning inserted for automatic numbering only 736 G.4 No meaning inserted for automatic numbering only 737 G.5 No meaning inserted for automatic numbering only 738 G.6 PS Alien NEXT modelling 739 G.6.1 General 740 The PS Alien NEXT (PS ANEXT) model is similar to the model used for NEXT. 741 Each pair-to-pair alien NEXT (ANEXT) contribution is modelled exactly the same as internal link NEXT; 742 see clause G.3. Therefore, The PS Alien NEXT (PS ANEXT) model is similar to the model used for 743 NEXT. 744 Simple models assume equal lengths of disturbed and disturber links and co-location of connecting 745 hardware (patch panels). In situations where the lengths of disturbed and disturber are different, 746 corrections need to be applied which depend on the length over which alien crosstalk coupling occurs. 747 G.6.2 PS Alien NEXT between connectors 748 The PS Alien NEXT between connectors is modelled as: 749 PSANEXT = PSANEXT − 20 log( f / 100 ) Conn, dB Conn, const, dB 750 G.6.3 PS Alien NEXT between cable segments 751 The PS Alien NEXT between cables is modelled as: ⎛ L ⎞ ⎜ dα ⎟ ⎜ 100 cable, 100 m, dB ⎟ ⎜ − ⎟ 752 1 − 10 5 (G-29) PSANEXT = PSANEXT − 15log( f / 100 ) − 10 log⎜ ⎟ Cable, dB Cable, const, dB ⎜ −α ⎟ ⎜ − cable, 100 m, dB ⎟ ⎜ 5 ⎟ ⎜ 1 − 10 ⎟ ⎝ ⎠ 753 In this case L is the length over which the ANEXT coupling takes place. d 754 Refer to clause G.3.1 for a description of the length dependency portion of equation G-29. ISO/IEC JTC 1/SC 25N1318c.doc 47 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 48 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 755 G.6.4 Principles of link modelling 756 Worst case conditions occur where ANEXT coupling occurs over the full length of disturber and 757 disturbed cabling and where all connections within each link are co-located. If ANEXT coupling does not 758 occur right from the beginning of the point of measurement, the impact is reduced by the sum insertion 759 loss of the uncoupled cabling segments of disturber and disturbed links. The highest influence on the 760 overall ANEXT coupling originates from the beginning of the cabling. 761 For details of PS ANEXT predictions refer to clause G.3. 762 Excess ANEXT contributions that result from unbalanced signals and differential-to-common and 763 common-to-differential mode coupling are ignored. These can be significant at high frequencies and 764 when balance properties of the cabling are poor. 765 G.7 PS Alien ACR-F modelling 766 G.7.1 General 767 The PS Alien ACR-F (PS AACR-F) model is similar to the model used for ACR-F. 768 Each pair-to-pair alien ACR-F (AACR-F) contribution is modelled exactly the same as internal link ACR- 769 F; see clause A.4. Therefore, The PS Alien ACR-F (PS AACR-F) model is similar to the model used for 770 ACR-F. 771 Simple models assume equal lengths of disturbed and disturber links and co-location of connecting 772 hardware (patch panels). In situations where the lengths of disturbed and disturber are different, 773 corrections need to be applied which depend on the length over which alien crosstalk coupling occurs. 774 The length dependency is as described in clause G.4.2. The PS Alien FEXT is obtained by adding the 775 insertion loss to the ACR-F. 776 G.7.2 PS AFEXT between connectors 777 The PS AFEXT between connectors is modelled as: 778 PSAFEXT = PSAFEXT − 20 log( f / 100 ) Conn, dB Conn, const, dB 779 G.7.3 PS AACR-F between cable segments 780 The PS AACR-F between cables is modelled as: ⎛L ⎞ 781 PSAACR_F = PSAACR_F − 20 log( f / 100 ) − 10log⎜ d ⎟ (G-30) Cable, dB Cable, const, dB ⎜ 100 ⎟ ⎝ ⎠ 782 Refer to clause G.4.1 for a description of the length dependency portion of equation G-30. 783 G.7.4 Principles of link modelling 784 Worst case conditions occur where AFEXT coupling occurs over the full length of disturber and 785 disturbed cabling, and where all connections within each link are co-located. 786 For details of PS AACR-F predictions refer to clause G.3. 787 Excess AFEXT contributions that result from unbalanced signals and differential-to-common and 788 common-to-differential mode coupling are ignored. These can be significant at high frequencies and 789 when balance properties of the cabling are poor. ISO/IEC JTC 1/SC 25N1318c.doc 48 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 49 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 790 G.7.5 Impact of PS ACR-F in links with substantially different lengths 791 The impact of each AFEXT measurement can be substantially increased when considering a short link 792 running in parallel with a long link. This can be the case when considering the conditions at a patch 793 panel where one link terminates from a nearby location and another link terminates from a distant 794 location. See Figure A-1. The disturbing link j has pairs I from 1 to 4, and is disturbing the selected link, 795 pair k. The intent is to test the performance of the cabling based on the “coupling length”. This coupling 796 length is effectively determined by the minimum insertion loss of the disturbing IL and disturbed link j 797 IL . k Disturbing link j IL i,j AFEXT k,i,j IL k Disturbed link Coupling length 798 799 Figure G.3: Example of increased impact of PS AFEXT. 800 In Figure G.3 the impact of the signal-to-noise ratio (SNR) at the near end receiver of the long channel 801 is considered. 802 G.7.5.1 Normalization for the coupling length 803 It is assumed that the coupling properties of cabling are consistent over length. 804 Over the coupling length, the AACR-F is defined as: 805 AACR − Fcoupled = AFEXT − IL (G-31) k, j k j 806 For nominally compliant cabling, the scaled ACR-F over the coupled length is given by: ⎛ Lj ⎞ ⎜ ⎟ 807 AACR − Fcoupled = AACR − F − 10 ⋅ log⎜ ⎟⎟ (G-32) k, j 100m ⎜ 100 ⎝ ⎠ 808 Therefore: ⎛ Lj ⎞ ⎜ ⎟ 809 AACR − F = AACR − Fcoupled + 10 ⋅ log⎜ (G-33) 100m k ⎜ 100 ⎟⎟ ⎝ ⎠ 810 If the coupling were to take place over the length of the disturbed link, the relationship for nominally 811 compliant cabling is: ISO/IEC JTC 1/SC 25N1318c.doc 49 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 50 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 ⎛L ⎞ 812 AACR − Fnormalized = AACR − F − 10 ⋅ log⎜ k ⎟ (G-34) k 100m ⎜ 100 ⎟ ⎝ ⎠ 813 ⎛ Lj ⎞ 814 AACR − Fnormalized = AACR − Fcoupled + 10 ⋅ log⎜ ⎟ − 10 ⋅ log⎛⎜ L k ⎞⎟ (G-35) k k ⎜ 100 ⎟ ⎜ 100 ⎟ ⎝ ⎠ ⎝ ⎠ ⎛ IL j ⎞ ⎜ ⎟ 815 AACR − Fnormalized = AACR − Fcoupled + 10 ⋅ log⎜ (G-36) k k ⎜ IL ⎟⎟ ⎝ k⎠ 816 The log ratio of lengths can be converted to a log ratio of insertion losses. It is suggested that the 817 average insertion losses of all pairs @ 250 MHz be used to compute the ratio. 818 G.7.5.2 Normalization for signal strengths 819 To correct for the coupling length, assuming the disturbed link is longer than the disturbed link and the 820 insertion loss of the coupling length (in this case the insertion loss of the disturbing link) is to be tested 821 requires a normalization that is equal to: 822 IL − IL (G-37) disturbed disturber 823 The AACR − Fcoupled is then computed as in equations (G-38) through (G-40) k 824 AACR − Fcoupled = AFEXT − IL − IL + IL = (G-38) k k j k k 825 AACR − Fcoupled = AFEXT − IL − ⎛⎜ IL − IL ⎞⎟ (G-39) k k k ⎝ j k⎠ 826 AACR − Fcoupled =AACR − F + ⎛⎜ IL − IL ⎞⎟ (G-40) k k ⎝ k j⎠ 827 In other words, the measured AFEXT needs to be adjusted “improved” by the difference of the insertion 828 losses of disturbed and disturbing links in order to reflect the AFEXT of the coupled length. 829 G.7.7.3 Total normalization 830 By combining the normalization for coupling length and the scaling for length, the correction to be 831 applied to every AFEXT result between a disturbed and a disturbing link becomes: ⎛ Lj ⎞ 832 AFEXT + IL − IL + 10 ⋅ log⎜ ⎟ (G-41) k, j k j ⎜L ⎟ ⎝ k⎠ 833 The log ratio of lengths can be converted to a log ratio of insertion losses. It is suggested that the 834 average insertion losses of all pairs @ 250 MHz be used to compute the ratio. ⎛ IL j @ 250MHz ⎞ ⎜ ⎟ 835 AFEXT ( f ) + IL ( f ) − IL ( f ) + 10 ⋅ log⎜ (G-42) k, j k j ⎜ L @ 250MHz ⎟⎟ ⎝ k ⎠ 836 Then the power sum is computed from all disturbing links on the same disturbed link, and to compute 837 the AACR-F (which were all normalized to the IL of the disturbed link) is obtained in the usual manner: 838 AACR_F = AFEXT − IL (G-43) k k k ISO/IEC JTC 1/SC 25N1318c.doc 50 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 51 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 839 Page 124: 840 Annex H – Class F channel and permanent link with two connections 841 Replace Table H.1: 842 Table H.1 – ACR and PS ACR values for 2 connection class F channels and permanent links at 843 key frequencies Channel Permanent link Frequency Minimum Minimum Minimum Minimum MHz ACR PS ACR ACR PS ACR dB dB dB dB 1 61,0 58,0 61,0 58,0 16 57.1 54.1 58,2 55,2 100 44,6 41.6 47,5 44,5 250 27,3 24,3 31,9 28,9 500 7,5 4,5 14,3 11,3 600 1,1 -1,9 8,6 5,6 844 Add Table H.2 for Class FA 845 Table H.2 – ACR and PS ACR values for 2 connection class F A channels and permanent links at 846 key frequencies Channel Permanent link Frequency Minimum Minimum Minimum Minimum MHz ACR PS ACR ACR PS ACR dB dB dB dB 1 62,8 59,8 63,1 60,1 16 57.1 54.1 58,2 55,2 100 45,1 42,1 47,9 44,9 250 31,0 28,1 35,5 32,5 500 11,7 8,8 18,1 15,2 600 5,6 2,7 12,7 9,8 1 000 -14,2 -17,1 -4,9 -7,8 847 Pages 125: 848 I.3 Structural elements 849 Replace: 850 The TP (transition point), which had no effect on the link and channel performance, has been removed 851 and the CP (consolidation point) was introduced. The effects of the CP on the link and channel 852 performance are taken in account. 853 By 854 The TP (transition point), which had no effect on the link and channel performance, has been removed 855 and the CP (consolidation point) was introduced. The effects of the CP on the link and channel 856 performance are taken into account. 857 Pages 132 to 133 858 Bibliography ISO/IEC JTC 1/SC 25N1318c.doc 51 11801 1 st PDAM 1.2 © ISO/IEC:2007 – 52 – ISO/IEC JTC 1/SC 25 N 1318 2007-05-02 859 Delete: 860 IEC 61076-3-104, Connectors for electronic equipment – Part 3-104: Detail specification for 8-way, 861 shielded free and fixed connectors, for data transmissions with frequencies up to 600 MHz (Under 862 consideration) 863 IEC 60068-2-2, Basic environmental testing procedures – Part 2: Tests – Tests B: Dry heat 864 IEC 60068-2-6, Environmental testing – Part 2: Tests – Tests Fc: Vibration (sinusoidal) 865 IEC 60068-2-60, Environmental testing – Part 2: Tests – Test Ke: Flowing mixed gas corrosion test 866 Insert: 867 IEEE 802.3an, Information technology — Telecommunications and information exchange between 868 systems — Local and metropolitan networks — specific requirements. Part 3: Carrier Sense Multiple 869 Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications — 870 Amendment: Physical Layer and Management. Parameters for 10 Gb/s Operation — Type 10GBASE-T 871 ISO/IEC 14165-114, Information technology - Fibre Channel - Part 114: 100 MB/s balanced copper 872 physical interface (FC-100-DF-EL-S) ISO/IEC JTC 1/SC 25N1318c.doc 52 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 873 Attachment 1 874 This attachment will not be published finally. during the development process of the 875 document is records the minimum requirements for cables that are specified in the 876 published document by reference to the appropriate cable standards. 877 Shadow list to Amendment 1 to ISO/IEC 11801 Ed.2:2002 for minimum requirements 878 for cables to meet the minimum permanent link/channel performance over the 879 maximum length of the reference implementation as specified in ISO/IEC 11801 2 nd 880 Ed Amendment 1. 881 ISO/IEC JTC 1 SC 25/WG 3 N 615 requires a document with tables as follows. 882 1. Those cable values which are needed for the channels specified in ISO/IEC 11801 883 shall be recorded in tables (working document of WG 3) during the process of 884 document development and approval and developed in dialog with the component 885 committees. 886 2. During the publication process those values which are either identical to those in IEC 887 cable specs are replaced by dated reference to the relevant part of IEC 61156 888 IEC 60793 and IEC 60794, those which are more stringent in ISO/IEC 11801 are 889 specified in ISO/IEC 11801 explicitly as given below. Those values where IEC 890 specifies a better performance than needed for the channel as specified in 891 ISO/IEC 11801, the IEC specifications are referenced and the minimum performance 892 needed to meet ISO/IEC 11801 are also provided in a footnote. 893 The following tables are based on 894 • ISO/IEC 11801:2002-09 895 • IEC 61156-5:2002-03 896 • IEC 61156-6:2002-03, 897 • Status of discussion on cable performance as known by the Secretary of 898 ISO/IEC JTC 1/SC 25 as of 2007-05-02 899 These values are subject to confirmation / change based on countries comments 900 based on channel and link simulations and feedback from IEC SC 46C. 901 These values will be implemented in the channel model, see SC 25 N 1321 as 902 default values. 903 NOTE These values can be freely changed also in the model with closed mathematics. 904 Originally established by Clause editor 2001-09-05, updated by Sec WG 3 2003-01-15 905 Updated by Sec S C25/WG 3 2007-04-20 ISO/IEC JTC 1/SC 25N1318c.doc 53 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 906 1 Minimum requirements for balanced cables 907 Table 1 - Mechanical characteristics of balanced cables Cable characteristics Units Subsystem 1 Mechanical characteristics Backbone Horizontal 1) 1.1 Diameter of conductor mm 0,4 to 0,8 2) 1.2 Diameter over insulated conductor mm ≤ 1,6 1.3 Number of conductors in a cable 2 per pair / element 4 per quad 3) 1.4 Screen around cable element Optional. 1.5 Number of cable ≥ 4 pairs 2, 4, n (n > 4) pairs elements in a unit ≥ 2 quads 1, 2, n (n > 2) quads 3) 1.6 Screen around cable unit Optional 3) 1.7 Screen around cable Optional. 4) 1.8 Outer diameter of cable mm ≤ 90 ≤ 20 1.9 Temperature range without neither °C installation: 0 to +50 mechanical nor electrical degradation operation: -20 to +60 5) 1.10 Minimum bending radius for pulling See manufacturers’ instructions during installation 1.11 Minimum bending radius installed 25 mm for four-pair cable with a diameter up to 6 mm 50 mm for four-pair cable with a diameter over 6 mm 6) 1.12 Pulling strength N ≥ 50 ⋅ A cu m in / mm² 1.13 Fire rating According to 3.5.9 of IEC 61156 unless otherwise requested by local regulation 1.14 Colour coding IEC 61156 1.15 Cable marking as required 1) Conductor diameters below 0,5 mm and above 0,65 mm may not be compatible with all connecting hardware. 2) Diameters over the insulated conductor up to 1,7 mm may be used if they meet all other performance requirements. These cables may not be compatible with all connecting hardware. 3) See clause 11 of ISO/IEC 11801 Ed.2. 4) Should be minimized to make best use of duct and cross-connect capacity (see clause 10 of ISO/IEC 11801). If the cable will be terminated in a plug, e.g. flexible cables, then cable unit diameters above 9 mm may not be compatible with all connecting hardware (see clause 10 of ISO/IEC 11801). 5) For certain applications (e.g. precabling buildings in cold climate) a cable with a lower temperature bending performance of -30 °C may be required. 6) This is an indication for cable performance. This results in a maximum pulling force of 50 N/mm² times copper conductor cross-section, excluding screens if present. A cu min is the minimum copper cross section. Additional strength members increase the pulling strength. 908 ISO/IEC JTC 1/SC 25N1318c.doc 54 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 909 Table 2 - Electrical characteristics of balanced cables Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 2.1 Mean characteristic impedance (100 m cable) 0) Measured according to 3.3.6.2.3 of IEC 61156-1 amendment 2:2001 method A on a standard length of 100 m 100 Ω cable Ω 100 100 ± 5 100 ± 5 100 ± 5 100 ± 5 100 ± 5 4) 2.2 Minimum return loss dB 4 to 10 20+5lg(f) 20+5lg(f) 20+5lg(f) 20+5lg(f) 20+5lg(f) (100 m cable) >10 to 20 25 25 25 25 25 >20 to 100 25-7lg(f/20) 25-7lg(f/20) 25-7lg(f/20) 25-7lg(f/20) 25-7lg(f/20) >100 to 250 N/A 25-7lg(f/20) 25-7lg(f/20) 25-7lg(f/20) 25-7lg(f/20) >250 to 500 N/A N/A 17,3 17,3 17,3 >500 to 600 N/A N/A N/A 17,3 17,3 >600 to 1 000 N/A N/A N/A N/A 17,3 – 10lg(f/600) Minimum return loss at key dB 1 N/A N/A N/A N/A N/A frequencies (100 m cable) 100 20,1 20,1 20,1 20,1 20,1 250 N/A 17,3 17,3 17,3 17,3 500 N/A N/A 17,3 17,3 17,3 600 N/A N/A N/A 17,3 17,3 1 000 N/A N/A N/A N/A 15,1 1) 2.3 Maximum attenuation 100 Ω cable dB/ 1 to 100 1,9108*√f+ 1,82*√f+ 1,82*√f+ 1,8*√f+ 1,8*√f+ 100 0,0222*f+0,2/√f 0,017*f+0,25 /√f 0,0091*f+0,25 /√f 0,01*f+0,25/√f 0,005*f+0,25/√f m >100 to 250 N/A >250 to 500 N/A N/A >500 to 600 N/A N/A N/A >600 to 1 000 N/A N/A N/A N/A 100 Ω cable maximum dB/ 1 2,1 2,1 2,1 2,0 2,0 attenuation at key 100 100 21,3 19,9 19,1 19,0 18,5 ISO/IEC JTC 1/SC 25N1318c.doc 55 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A frequencies m 250 N/A 33,0 31,1 31,0 29,7 500 N/A N/A 45,3 45,3 42,8 600 N/A N/A N/A 50,1 47,1 1 000 N/A N/A N/A N/A 61,9 2) 3) 2.4 Minimum NEXT loss dB 65,3-15lgf 75,3-15lgf 74,3-15lgf 102,4-15lgf 108,4-15lgf (100 m cable) 1<f≤100 1<f≤250 1<f≤500 1<f≤600 1<f≤1 000 Minimum NEXT loss at key dB 1 65 75 74,3 75 80 frequencies (100 m cable) 100 35 44 44,3 72 78,4 250 N/A 39 38,3 66 72,4 500 N/A N/A 33,8 61,9 67,9 600 N/A N/A N/A 61 66,7 1 000 N/A N/A N/A N/A 63,4 3) 2.5 Minimum PS NEXT loss dB 62,3-15lgf 72,3-15lgf 71,3-15lgf 99,4-15lgf 105,4-15lgf (100 m cable) 1<f≤100 1<f≤250 1<f≤500 1<f≤600 1<f≤1 000 Minimum PS NEXT loss at dB 1 62 72 71,3 75 77 key frequencies (100 m cable) 100 32 42 41,3 69 75,4 250 N/A 36 35,3 63 69,4 500 N/A N/A 30,8 58,9 64,9 600 N/A N/A N/A 58 63,7 1 000 N/A N/A N/A N/A 60,4 2.8 Minimum ELFEXT loss dB 1 to 100 63,8-20lg(f) 67,8-20lg(f) 67,8-20lg(f) 94-20lg(f) 95,3-20lg(f) 3) (100 m cable) >100 to 250 N/A 67,8-20lg(f) 67,8 94-20lg(f) 95,3-20lg(f) New name ACR-F >250 to 500 N/A N/A 67,8 94-20lg(f) 95,3-20lg(f) >500 to 600 N/A N/A N/A 94-20lg(f) 95,3-20lg(f) >600 to 1 000 N/A N/A N/A N/A 95,3-20lg(f) Minimum ELFEXT loss at dB 1 64,0 68,0 68,0 75,0 75,0 key frequencies 100 24,0 28,0 28,0 54,0 55,3 ISO/IEC JTC 1/SC 25N1318c.doc 56 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A (100 m cable) 250 N/A 20,0 20,0 46,0 47,3 500 N/A N/A 13,8 40,0 41,3 600 N/A N/A N/A 38,4 39,7 1 000 N/A N/A N/A N/A 35,3 2.9 Minimum PS ELFEXT loss dB 1 to 100 61-20lg(f) 65-20lg(f) 64,8-20lg(f) 91-20lg(f) 95,3-20lg(f) 3 (100 m cable) ) >100 to 250 N/A 65-20lg(f) 64,8-20lg(f) 91-20lg(f) 95,3-20lg(f) New name PS ACR-F >250 to 500 N/A N/A 64,8-20lg(f) 91-20lg(f) 95,3-20lg(f) >500 to 600 N/A N/A N/A 91-20lg(f) 95,3-20lg(f) >600 to 1 000 N/A N/A N/A N/A 95,3-20lg(f) Minimum PS ELFEXT loss at dB 1 61,0 65,0 64,8 75,0 78 key frequencies (100 m cable) 100 21,0 25,0 24,8 51,0 55 250 N/A 17,0 16,8 43,0 47 500 N/A N/A 10,8 37,0 41 600 N/A N/A N/A 35,4 40 1 000 N/A N/A N/A N/A 35 2.10 Maximum d.c. loop Ω/ 19 19 19 19 19 resistance 100 m 2.11 Maximum resistance refer % 2 2 2 2 2 unbalance to IEC 6 1156 2.12 Minimum d.c. current mA 175 175 175 175 175 carrying capacity per conductor 2.13 Operating voltage V 72 2.15 Maximum propagation delay µs/ 1 to 100 0,534 + 0,036 / √f 0,534 + 0,036 / √f 0,534 + 0,036 / √f 0,534 + 0,036 / √f 0,534 + 0,036 / √f per 100 m 100 0,534 + 0,036 / √f m >100 to 250 N/A 0,534 + 0,036 / √f 0,534 + 0,036 / √f 0,534 + 0,036 / √f >250 to 500 N/A N/A 0,534 + 0,036 / √f 0,534 + 0,036 / √f 0,534 + 0,036 / √f ISO/IEC JTC 1/SC 25N1318c.doc 57 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A >500 to 600 N/A N/A N/A 0,534 + 0,036 / √f 0,534 + 0,036 / √f >600 to 1 000 N/A N/A N/A N/A 0,534 + 0,036 / √f Maximum propagation delay 1 0,570 0,570 0,570 0,570 0,570 at key frequencies 100 0,538 0,538 0,538 0,538 0,538 250 N/A 0,536 0,536 0,536 0,536 500 N/A N/A 0,536 0,536 0,536 600 N/A N/A N/A 0,535 0,535 1 000 N/A N/A N/A N/A 0,535 2.16 Maximum delay skew per ns/ 1 to 100 45 45 45 25 25 100 m 100 m >100 to 250 N/A 45 45 25 25 >250 to 500 N/A N/A 45 25 25 >500 to 600 N/A N/A 45 25 25 >600 to 1 000 N/A N/A N/A N/A 25 6) 6) 2.17 Minimum near end dB 1 to 100 40-10lg(f) f.f.s 40-10lg(f) f.f.s 50-10lg(f) 40-10lg(f) f.f.s 40-10lg(f) unbalance attenuation unscreened screened (transverse conversion loss, 6) TCL) (100 m cable) 40-10lg(f) screened 6) 6) 6) >100 to 250 N/A 40-10lg(f) f.f.s 50-10lg(f) 50-10lg(f) 50-10lg(f) unscreened unscreened 40-10lg(f) f.f.s 40-10lg(f) sreened screened 6) >250 to 500 N/A N/A 50-10lg(f) f.f.s >500 to 600 N/A N/A N/A f.f.s >600 to 1 000 N/A N/A N/A N/A 6) 6) Minimum near end dB 1 40 f.f.s 40 f.f.s 50 40 f.f.s 40 unbalance attenuation at key 6) frequencies 50 (100 m cable) 6) 6) 100 20 f.f.s 20 f.f.s 30 20 f.f.s 30 6) 30 ISO/IEC JTC 1/SC 25N1318c.doc 58 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 6) 250 N/A 16 16 16 16 500 N/A N/A 600 N/A N/A N/A 1 000 N/A N/A N/A N/A 2.18 Coupling attenuation Screened cable (Type II) dB 30 to 100 55 55 55 80 >100 to 250 55-20lg(f) >100 to 500 55-20lg(f) >100 to 600 55-20lg(f) >100 to 1 000 80-20lg(f) Unscreened cable (Type III) dB 30 to 100 40 40 40 10 >100 to 250 40-20lg(f) 10 >100 to 500 f.f.s 20 >100 to 600 40-20lg(f) 100 >100 to 1 000 f.f.s 2.19 Maximum transfer mΩ/m 1 50 50 50 50 10 impedance for screened cables 10 100 100 100 100 10 30 200 200 200 200 20 100 1 000 1 000 1 000 1 000 100 2.20 Minimum d.c. insulation MΩ 150 resistance km 2.20 Dielectric strength 1 kV d.c. for 1 min or 2,5 kV d.c. for 2 s conductor/conductor and conductor/screen 0,7 kV a.c. for 1 min or 1,7 kV a.c. for 2 s 2.21 Maximum capacitance PF/k 0,001 1 600 1 600 1 600 1 600 1 600 unbalance pair to ground m 2.22 Minimum PS ANEXT loss dB >1 to 100 Not defined Not defined 80-10lg(f) as good as 6A 95-10lg(f) (100 m cable) >100 to 500 90-15lg(f) 105-15lg(f) ISO/IEC JTC 1/SC 25N1318c.doc 59 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A At least channel values >500 to 1000 N/A 105-15lg(f) Minimum PS NEXT loss at dB 1 Not defined Not defined 80 95 key frequencies (100 m cable) 100 Not defined Not defined 60 75 250 N/A Not defined 54 69 500 N/A N/A 49,5 64,5 600 N/A N/A N/A 63,3 1 000 N/A N/A N/A N/A 60 2.22 Minimum PS AACR-F dB >1 to 500 Not defined Not defined 77-20lg(f) as good as 6A N/A (100 m cable) >1 to 1000 Not defined Not defined N/A N/A 92-20lg(f) At least channel values Minimum PS AACR-F at key dB 1 Not defined Not defined 77 92 frequencies (100 m cable) 100 Not defined Not defined 37 52 250 N/A Not defined 29 44 500 N/A N/A 23 38 600 N/A N/A N/A N/A 36,5 1 000 N/A N/A N/A N/A 32 0) Alternate test methodologies which have been shown to correlate with these requirements may also be used. 1) Calculations that result in attenuation below 4 dB shall revert to a requirement of 4 dB. 2) Unless otherwise specified, cable NEXT loss performance shall be characterized using "worst case pair combination" testing. See 9.3 for additional NEXT loss requirements for balanced cables. 3) Calculations that result in values in excess of 75 dB shall revert to a requirement of 75 dB minimum. If FEXT is greater than 70 dB, ELFEXT and PSELFEXT need not be measured. 4) Mean impedance plus return loss shall be measured on a test length of 100 m. Alternate test methodologies which have been shown to correlate with these requirements may also be used. Return loss values for frequencies below 4 MHz are for information only. 5) This shall be supported by a maximum ambient temperature of 60 °C 6) this requirement is only applicable to unshielded cables 910 Flexible cables shall meet the requirements specified in, with the exception of attenuation, d.c. loop resistance and return Loss (RL) that shall 911 meet the values specified in Table . ISO/IEC JTC 1/SC 25N1318c.doc 60 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 912 Table 3 - Electrical characteristics of flexible balanced cables 913 (for cat 6A and 7A only as far as not identical with fixed cables) Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 4) 2.2 Minimum return loss dB 4 to 10 20+5lg(f) 20+5lg(f) 20+5lg(f) 20+5lg(f) 20+5lg(f) (100 m cable) >10 to 20 25 25 25 25 25 >20 to 100 25-8,6lg(f/20) 25-8,6lg(f/20) 25-8,6lg(f/20) 25-8,6lg(f/20) 25-8,6lg(f/20) >100 to 250 N/A 25-8,6lg(f/20) 25-8,6lg(f/20) 25-8,6lg(f/20) 25-8,6lg(f/20) >250 to 500 N/A N/A 15,6 15,6 15,6 >500 to 600 N/A N/A N/A 15,6 15,6 >600 to 1 000 N/A N/A N/A N/A 15,6-10log(f/600) Minimum return loss at key dB 1 N/A N/A N/A N/A N/A frequencies (100 m cable) 100 20,1 20,1 20,1 20,1 20,1 250 N/A 15,6 15,6 15,6 15,6 500 N/A N/A 15,6 15,6 15,6 600 N/A N/A N/A 15,6 15,6 1 000 N/A N/A N/A N/A 13,4 1) 2.3 Maximum attenuation dB/ 1 to 100 2,866*√f+ 2,73*√f+ 2,73*√f+ 2,7*√f+ 2,7*√f+ 100 m 0,033*f+0,3/√f 0,026*f+0,375/√f 0,014*f+0,375 /√f 0,015*f+0,3/√f 0,015*f+0,3/√f 100 Ω cable >100 to 250 N/A horizontal cable attenuationx1,5 >250 to 500 N/A N/A >500 to 600 N/A N/A N/A >600 to 1 000 N/A N/A N/A N/A 100 Ω cable maximum dB/ 1 3,2 3,1 3,0 3,0 3,0 attenuation at key 100 m frequencies 100 32 29,9 28,5 28,5 28,5 250 N/A 49,7 46,5 46,5 46,5 500 N/A N/A 67,9 67,9 67,9 600 N/A N/A N/A 75,1 75,1 ISO/IEC JTC 1/SC 25N1318c.doc 61 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 1 000 N/A N/A N/A N/A 100,4 2.8 Minimum ELFEXT loss dB 1 to 100 63,8-20lg(f) 67,8-20lg(f) 94-20lg(f) 94-20lg(f) 3) (100 m cable) >100 to 250 N/A 67,8-20lg(f) 94-20lg(f) 94-20lg(f) >250 to 500 N/A N/A 94-20lg(f) 94-20lg(f) >500 to 600 N/A N/A N/A 94-20lg(f) 94-20lg(f) >600 to 1 000 N/A N/A N/A N/A 94-20lg(f) Minimum ELFEXT loss at dB 1 64,0 68,0 75,0 75,0 key frequencies (100 m cable) 100 24,0 28,0 54,0 54,0 250 N/A 20,0 46,0 46,0 500 N/A N/A 600 N/A N/A N/A 38,4 38,4 1 000 N/A N/A N/A N/A 34 2.9 Minimum PS ELFEXT loss dB 1 to 100 61-20lg(f) 65-20lg(f) 91-20lg(f) 91-20lg(f) 3 (100 m cable) ) >100 to 250 N/A 65-20lg(f) 91-20lg(f) 91-20lg(f) >250 to 500 N/A N/A 91-20lg(f) 91-20lg(f) >500 to 600 N/A N/A N/A 91-20lg(f) 91-20lg(f) >600 to 1 000 N/A N/A N/A N/A 91-20lg(f) Minimum PS ELFEXT loss at dB 1 61,0 65,0 75,0 75,0 key frequencies (100 m cable) 100 21,0 25,0 51,0 51,0 250 N/A 17,0 43,0 43,0 500 N/A N/A 31 31 600 N/A N/A N/A 35,4 35,4 1 000 N/A N/A N/A N/A 31 2.1 Maximum d.c. loop Ω/ 29 29 29 29 29 0 resistance 100 m ISO/IEC JTC 1/SC 25N1318c.doc 62 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 2.1 Minimum near end dB 1 to 100 40-10lg(f) 40-10lg(f) 40-10lg(f) 40-10lg(f) 40-10lg(f) 7 unbalance attenuation (transverse conversion loss, >100 to 250 N/A 40-10lg(f) 40-10lg(f) 40-10lg(f) 40-10lg(f) TCL) (100 m cable) >250 to 500 N/A N/A ffs >500 to 600 N/A N/A N/A ffs >600 to 1 000 N/A N/A N/A N/A Minimum near end dB 1 40 40 40 40 40 unbalance attenuation at key frequencies 100 20 20 20 20 20 (100 m cable) 250 N/A 16 16 16 16 500 N/A N/A Ffs 600 N/A N/A N/A ffs 1 000 N/A N/A N/A N/A 914 915 Table 4 - PS NEXT loss of balanced backbone cables Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 1) 4.1 Minimum PS NEXT loss dB 66,3-15lgf 1<f≤100 76,0-15lgf 1<f≤250 103,4-15lgf 1<f≤600 103,4-15lgf 1<f≤1 000 (100 m cable) 4.2 Minimum PS NEXT loss at dB 1 66,3 75,0 75,0 75,0 key frequencies (100 m cable) 100 35,3 45 72 72 250 N/A 39 66 66 500 N/A N/A 600 N/A N/A N/A 61 61 1 000 N/A N/A N/A N/A 58,5 1) Unless otherwise specified, cable NEXT loss performance shall be characterized using "worst case pair combination" testing. Calculations that result in values in excess of 75 dB shall revert to a requirement of 75 dB minimum. 916 ISO/IEC JTC 1/SC 25N1318c.doc 63 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 917 Table 5 - PS NEXT loss of balanced cables connected to more than one TO Electrical characteristics Units f/MHz Cat. 5 Cat. 6 Cat. 6 A Cat. 7 Cat. 7 A 1) 5.1 Minimum PS NEXT loss dB 68-15lgf 77-15lgf 77,3-15lgf 105,4-15lgf 111,4-15lgf (100 m cable) 1<f≤100 1<f≤250 1<f≤500 1<f≤600 1<f≤1 000 5.2 Minimum PS NEXT loss at dB 1 68,0 75,0 75,0 75,0 80 key frequencies (100 m cable) 100 38,0 45,3 47,3 75,0 81,4 250 N/A 39,3 41,3 69,4 75,4 500 N/A N/A 36,8 70,9 600 N/A N/A N/A 63,7 69,7 1 000 N/A N/A N/A N/A 66,4 1) Unless otherwise specified, cable NEXT loss performance shall be characterized using "worst case pair combination" testing. Calculations that result in values in excess of 75 dB shall revert to a requirement of 75 dB minimum. ISO/IEC JTC 1/SC 25N1318c.doc 64 ISO/IEC JTC 1/SC 25 SC 25 N 1318 2007-05-02 918 2 Minimum requirements for optical fibre cables 919 Table 6 - Optical fibre cable attenuation Maximum cable attenuation dB/km OM1, OM2, and OM3 Multimode OS1 Singlemode wavelength 850 nm 1 300 nm 1 310 nm 1 550 nm Attenuation 3,5 1,5 1,0 1,0 The attenuation shall be measured in accordance with IEC 60793-1-40 and IEC 60793-1-41 respectively 920 Maximum propagation delay 921 Then maximum propagation delay shall be 5,00 ns/m (0,667 c). 922 Multi mode optical fibre requirements 923 The optical fibre shall be multimode, graded-index optical fibre waveguide with 924 nominal 50/125 µm or 62,5/125 µm core/cladding diameter and numerical aperture 925 complying with A1a or A1b optical fibre as defined in IEC 60793-2-10. 926 Physical cable requirements 927 The indoor and outdoor optical fibre cable shall meet mechanical and environmental 928 requirements specified in IEC 60794-2 and IEC 60794-3 respectively. 929 Table 7 - Multimode Optical fibre modal bandwidth Minimum modal bandwidth MHz•km Optical fibre type Core diameter Overfilled Launch Bandwidth Effective Laser in µm Launch Bandwidth 850 nm 1 300 nm 850 nm OM1 50 or 62,5 200 500 Not specified OM2 50 or 62,5 500 500 Not specified OM3 62,5 1500 500 2 000 Modal bandwidth shall be measured in accordance with IEC 60793-1-40 and IEC 60793-1-41 respectively NOTE - Effective laser launch bandwidth is assured using differential mode delay (DMD) as specified in the draft document IEC 60793-1-49. Optical fibres that meet only the overfilled launch modal bandwidth may not support some applications specified in Annex E. 930 Single-mode optical fibre requirements 931 The optical fibre shall comply with IEC 60793-2-50 type B1 and ITU-T G.652. 932 Cut-off wavelength 933 The cut-off wavelength of cabled single-mode optical fibre shall be less than 1 260 nm 934 when measured in accordance with IEC 60793-1-44. 935 Physical cable requirements 936 The indoor and outdoor optical fibre cable shall meet mechanical and environmental 937 requirements from IEC 60794-2 and IEC 60794-3 respectively. ISO/IEC JTC 1/SC 25N1318c.doc 65
Copyright © 2024 DOKUMEN.SITE Inc.