ISO 724-1993

INTERNATIONAL STANDARD ISO 724:1993TECHNICAL CORRIGENDUM 1 Published 2009-07-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION ISO general-purpose metric screw threads — Basic dimensions TECHNICAL CORRIGENDUM 1 Filetages métriques ISO pour usages généraux — Dimensions de base RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO 724:1993 was prepared by Technical Committee ISO/TC 1, Screw threads. Page 1, Normative references Delete the references to ISO 68 and ISO 261. Replace the reference to ISO 5408 with the following: ISO 5408, Screw threads — Vocabulary Page 5, Table 1 Add a pitch of 8 for nominal diameters 125 mm, 130 mm and 140 mm, respectively, by adding three new rows as follows: --`,,```,,,,````-`-`,,`,,`,`,,`--- ICS 21.040.10 Ref. No. ISO 724:1993/Cor.1:2009(E) © ISO 2009 – All rights reserved Published in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale 835 3 123.505 1.026 74.752 4 92.051 96.051 141.505 6 96.835 80 3 78.051 86.804 116. d D.670 3 153.835 8 144.701 79.340 6 106.402 80.051 91.```.````-`-`.835 95 3 93..505 4 142.835 6 141.103 148.505 3 128.835 2 113.835 130 4 127.103 93.505 6 101. d2 D1. d1 D.701 75.051 81.701 82.670 3 138.835 4 132.701 87.505 4 107.103 133.670 115 76 3 74.670 6 86.701 132.670 8 124.835 90 3 88.103 88.402 75.701 147.505 3 118.376 125 4 122.5 75..505 3 133.402 140.103 143. d2 D1.103 78.752 105 3 103.701 92.752 100 3 98.340 2 78.701 97...340 2 93.752 4 77.505 2 83.103 103.`.670 150 4 147.402 145.505 78 2 76.752 --`. ISO 724:1993/Cor.103 138.051 72.051 136.670 4 97.752 4 87.103 128.402 125.`.804 141.701 102.670 2 118.701 73.051 76.103 69.670 82 2 80.051 121.752 6 131.752 8 134.752 6 81.752 6 126.505 2 123.051 151.752 8 119.670 2 128.402 110.`.835 4 117.701 142.505 6 146.752 2 74.`--- 2 Copyright International Organization for Standardization © ISO 2009 – All rights reserved Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale .402 130.835 6 151.103 113.051 126.505 140 4 137.835 4 82. d 6 72.701 77.103 118.670 3 143.505 155 4 152.026 78.402 85.051 106.752 3 148.835 6 121.402 150.051 111.835 2 103.103 73.505 2 88.670 145 4 102.670 120 6 76.670 2 133.051 131.701 127.670 4 112.402 135. d1 D2.752 2 138.835 1.701 112.402 115.670 110 3 108.103 123.701 122.835 2 148.701 117.835 2 98.376 6 116..402 105.402 100.402 90.505 4 73.1:2009(E) Nominal Nominal diameter Pitch Minor diameter Pitch Minor Pitch Pitch = Major diameter diameter = Major diameter diameter diameter P diameter P D2.402 120.402 71.402 95.340 85 3 83.752 3 113.505 6 111.051 101.670 135 6 91.752 2 108.103 83.701 137.051 146.804 121.051 116..835 6 136..752 2 143.103 98.103 108.5 79.701 107.804 131. 1:2009(E) Page 8 Add the following bibliography at the end of the document.`.```.`.`.`--- Copyright International Organization for Standardization © ISO 2009 – All rights reserved 3 Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ... ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads [2] ISO 261... following Table 1: Bibliography [1] ISO 68-1.````-`-`. ISO 724:1993/Cor. ISO general purpose metric screw threads — General plan --`....