4CH STANDALONE DVR SYSTEM2010 NOV. Ver 1.5 i WARNING Do not install the DVR under the environment of exposing under the sunlight directly; heat or moisture environment to minimize the DVR performance and the dangerous of electricity leak. Do not touch power cord or power plug when the hand is in wet. Do not bend the power cable forcedly or put heavy materials on the power cable do not press it with heavy materials to avoid high voltage shock or machine damaged. Do not use damaged power cords or loose outlet plugs. Do not use the power outlet sharing with other electrical equipments. Please use the individual power outlet for the machine. Don not disassemble, repair, and modify this machine. Please contact local agaent if the machine needs to repair. Do not open case of the machine or insert any object. CAUTION Do not place the machine on an unlevel or an uneven surface. Could minimize the efficiency or malfunction Do not vibrate or shock the machine while in operation Could damage the HDD or the machine. CAUTION Make sure the voltage selector swich(115V/230V) is set to the appropriate setting before plug in！ ii Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 【 【 【 【 【 【 【 【 【 【 【 【 【 【 【 【 【 【 【 【 Specification 】 ..........................................................................................1 Front Panel 】 .............................................................................................2 Rear Panel 】 ..............................................................................................3 System Installation】 ...................................................................................3 System Operation 】 ...................................................................................4 Display Setup 】 .........................................................................................5 Main Menu Setup 】 ...................................................................................8 Camera Setup 】 .........................................................................................8 Record Setup】 ..........................................................................................10 Sensor Setup 】.........................................................................................12 Motion Setup 】........................................................................................13 Network Setup 】 .....................................................................................14 Audio Setup 】 .........................................................................................16 Backup Setup 】 .......................................................................................17 System Setup 】........................................................................................18 Search Setup 】.........................................................................................23 Other Function 】 .....................................................................................26 Cell phone monitoring 】 .........................................................................26 AVPlayer Operation 】 .............................................................................27 Web Operation 】 .....................................................................................28 【 Default Setting 】 .....................................................................................33 【 Recording Time Table 】 ..........................................................................35 【 USB Compatibility 】...............................................................................35 iii 1.【 Specification 】 Video Format Video Input Audio Input Video Output Audio Output VGA Output Alarm Input Alarm Output Display Mode Display Resolution Recording Resolution Highest Hight Normal Highest Recording High frame Normal Compression Algorithm Operating System Triplex Recording Mode Schedule Recording Status Indicator (LED) Event Mode PAL 4CH Input / BNC 4CH Input / RCA 2CH Monitor Output / BNC 1CH Output / RCA 640x480 、 800x600 、 1024x768 、 1280x1024 、 1280x720 、 1440x900 (OPTIONAL) 4CH Alarm In Buzzer，Relay Out(1 CH N.O/ N.C) Full Mode, 4 Division, Circulate Auto Switcher 720 x 480 720 x 576 720 x 480 720 x 240 352 x 240 Max. 30 fps Max. 60 fps Max. 120 fps 720 x 576 720 x 288 352 x 288 Max. 25 fps Max. 50 fps Max. 100 fps NTSC Playback Network Protocol Communication Protocol HDD type HDD Management PTZ Control Archiving Firmware Update Multi-Language Control Mode Network Control Network Function Power Supply Unit Dimension Weight Ambient Temperature Modified H.264 Embedded Linux Record / Playback / Network Manual, Schedule, Event, Smart Full-Time, Motion, Alarm, No Recording Power, Record Alarm Trigger, Motion Trigger, Video Loss Recording Duration: OFF、1~30 sec. Normal: x1 multiple speed Fast Forward: x1/2 / x2 / x4 / x8 / x16 multiple speed Fast Rewind: x2 / x4 / x8 / x16 multiple speed Move 1 image per push button at still image (STILL Controller): Forward/ Backforward Searching Function: Time / Event TCP/IP / PPPoE / DHCP / SMTP / DDNS RS-485 SATA 3.5” * 2 pcs (Not include HDD)。 Automatic Formatting by System (Pre-Formatting Not Required) Internal Communication Protocol (PELCO P, PELCO D, MIKAMI) RS-485 interface Control USB 1.1/2.0 USB Host English / Chinese / Others FacePlate / IR Remote Controller/USB Mouse(optional) GUI / LAN IE Browser Live Play / Playback/PTZ Control DC 12V/4.1A(AC100V~240V 50/60HZ) 430mm (W)x300mm (D)x 48mm (H) Unit Weight (3.5Kgs) (Hard Drive not included) -5℃ ~ 45℃ 1 Under the playback mode. press the button to pause the playback. press MENU to go to upper menu. press the button to stop the operation or go to upper menu.【 Front Panel 】 USB port MENU USB Backup or Firmware update Under the live viewing mode. Under the menu mode.2. Quad display Under the live viewing mode. CH3 full screen display. The LED lights on when the slave HDD is written. press the button to enter playback mode. press MENU to enter the Quick Menu. CH1 full screen display. CH2 full screen display. Under the playback mode. The LED lights on when power on The LED lights on when the master HDD is written. CH4 full screen display. Under the live viewing mode. press the button to start/stop the auto switching function. Playback/Pause Stop Manual Record Rewind Playback: x2 / x4 / x8 / x16 Multiple Speed Fast Forward UP / Down Enter Power Indicator Master HDD Indicator Slave HDD Indicator CH1 CH2 CH3 CH4 Quad Auto Switching Playback: x1/2 / x2 / x4 / x8 / x16 Multiple Speed To move up or down of the selection setting in menu Press enter button to confirm setup or go into sub-menu. Press this button to start recording in live mode. 2 . RS-485 Alarm Sensor Input/Output/ RS-485 8 9 DC12V XGA Power Input PC Monitor Output 4. Power Supply 3 .【 System Installation】 Connect BNC connector of Cameras to the video input of the DVR Coaxial cable cat6 or the above is suggested.3.【 Rear Panel 】 1 1 2 3 4 5 6 2 3 4 5 6 7 8 9 USB Port VIDEO IN VIDEO OUT AUDIO OUT AUDIO IN LAN port USB Mouse 4 CH video input (BNC) 2 CH video output (BNC) 1 CH audio output (RCA) 4 CH audio input (RCA) RJ-45 Network Connection 7 ALARM. (Please refer to the system setup) Speed Dome Camera Pelco D、Pelco P & MIKAMI speed dome protocol supported. Please refer to the Network Setup ) Alarm I/O（Alarm） Please refer to the external alarm installation. (The DVR support Static IP、PPPOE. DVR Network Cabling Please connect HUB or IP swtich device to DVR LAN port by RJ-45 cable then make sure the LED of LAN is lighting on. DHCP. Please refer to the for PTZ setup. remote controller. right mouse click can go to Upper Menu. double click left button of mouse can enter the Selected Item of the Sub-Menu. Remote Controller Every button of remote controller is the same with front panel’s.Please use the particular DC12V switch power adaptor which comes with DVR in the box and plug into the power input of DVR in the rear panel. for installation. In main menu. Mouse Operation In live viewing mode. In menu. The DVR will go into the live viewing mode after power on. Remote Control Guide as below CH1 CH3 Mute Left Rewind Play CH2 CH4 UP Enter Down Pause Record Quad Display MENU Right Fast Forward Stop Virtual Keyboard Operation The virtual keyboard for text input displays as below: 4 . left mouse click can enter the Selected Item of the Sub-Menu. In menu.【 System Operation 】 There are three kinds of DVR control device: front panel. and mouse. the right mouse click will open the Quick Menu. 5. Use the mouse scroll wheel to adjust settings in menu. Menu Operation Direction Buttons to Select Item Enter the Sub-Menu of the Selected Item Adjust the Value of the Selected Item Go to Upper Menu Front Panel & Remote Controller [UP/Down] [Enter] [Left/Right] [MENU] Mouse [Moving Cursor] [Double Left Click]or [Left Click] [Mouse Scroll Wheel] [Right Click] 6. . 『L』 5 . There are four kinds of status icon: 『●』recording.【 Display Setup 】 There are three kinds of screen display mode: Live.Menu Operation Select Characters from Virtual Keyboard Input Characters Exit the Virtual Keyboard Front Panel & Remote Controller [Up/Down/Left/Right] [Enter] [MENU] Mouse [Moving Cursor] [Left Click] [Right Click] Button Descriptions of Virtual Keyboard < Delete the previous character Shift Switch letters between capitalization and lowercase Enter Save the text and exit the virtual keyboard Other Buttons Input the character Menu Operation The pen image icon. PTZ. Auto Switching. means it has the sub-menu. 『M』motion triggered. the system will enter the live viewing mode. LIVE mode After bootup the DVR. Status Icon Menu Operation CH1 Display CH2 Display CH3 Display CH4 Display Quad Display Enter Quick Menu Enter the Playback Mode Start/Stop the Manual Recording Start/Stop the Auto Switching Start/Stop the PTZ Auto Tour Enable/Disable the Mute Function Front Panel & Remote Controller [CH1] [CH2] [CH3] [CH4] [Quad] [MENU] [Playback] [Record] Panel: press [Auto Switching]or Controller: press [Quad Display] Press [Forward] under full screen display Panel: press [Rewind] Controller:press [Mute] Mouse Double Left Click on the CH1 Double Left Click on the CH2 Double Left Click on the CH3 Double Left Click on the CH4 Double Left Click on the full screen [Right Click] Quick Menu Menu Operation Direction Buttons to Select Item Front Panel & Remote Controller [Left/Right] 6 Mouse [Moving Cursor] .video loss.『A』alarm triggered. CH4. Before this setting. CH3. Menu Operation Front Panel & Remote Mouse Controller [Mouse Scroll Wheel] 1 [Left Click] Z+ [Left Click] Z[Left Click] F+ [Left Click] F[Mouse Scroll Wheel] [Left/Right Click] [Mouse Scroll Wheel] (1)[Enter] to choose the Set the Preset Point: preset position 1~20 (2)[Up/Down] to select (3)[MENU] to Exit Zoom ＋ Zoom － Focus ＋ Focus － Set PTZ Position: Upward/Downward Set PTZ Position: Upward/Downward Go Back to the Live Viewing Mode [CH1] [CH2] [CH3] [CH4] [Up/Down] [Left/Right] [MENU] Auto Switching Auto Switching starts in the order of CH1. Quad. CH2. Please disable this function with the below operation: 7 . please go to 【PTZ】to setup first.Enter the Main Menu Start/Stop Manual Recording Enter the playback function Start to Auto Switching (1)Select【SETUP】 (2)[ENTER] (1) Select【MANUAL RECORD】 (2)[ENTER] (1)Select【SEARCH】 (2)[ENTER] (1)Select【Auto Switching】 under full screen display (2)[ENTER] (1)Select【PTZ】 (2)[ENTER] (1)Select【SYSTEM INFO】 (2)[ENTER] (1)Select【SETUP】 (2)[Left Click] (1)Select【MANUAL RECORD】 (2)[Left Click] (1)SELECT【SEARCH】 (2)[Left Click] (1)Select 【Auto Switching】under full screen display (2)[Left Click] (1)Select【PTZ】 (2)[Left Click] (1)Select【SYSTEM INFO】 (2) [Left-Click] Enter PTZ Operation Enter SYSTEM INFO PTZ Please understand the usage of the speed dome before set up the【PTZ】. 【 Main Menu Setup 】 Menu Operation Direction Buttons to Select Item Enter the Sub-Menu of the Selected Item Exit the Main Menu Front Panel & Remote Controller [Up/Down/Left/Right] [Enter] [MENU] Mouse [Moving Cursor] [Left Click] [Right Click] After changing settings.【 Camera Setup 】 8 . the system will ask the below question before you exit the Main Menu. Please press the [Quad Display] on Controller again.Please press the [Auto Switching] on panel again. Menu Operation Save Menu Config: Yes/No Confirm the setting Front Panel & Remote Controller [Left/Right] [Enter] Mouse [Moving Cursor] [Left Click] 8. Please press the [Left Click] on mouse again. 7. CHANNEL CH1~CH4: Apply settings to the selected channel. PRESET If the tour time is “ON”. DISPLAY ON/OFF: Enable or disable the camera display. SATURATION Set the value from 0~50. TYPE Set PTZ model No. 9 . please must select proper protocol type. the system will activate the auto-tour of the camera automatically. LOSS ALARM DURATION PTZ 1~30 (seconds) / OFF: set the alarm time for video loss. BRIGHTNESS CONTRAST HUE Set the value from 0~50. LOSS BUZZER DURATION 1~30 (seconds) / OFF: set time of the buzzer beeping for the video loss. Set the value from 0~50.: PTC-301、PTC-203ST、FUM 626、JG_QG988、FUM 622SD、FUM 628 or OFF. TITLE Use the virtual keyboard to input the camera name. Set the value from 0~50. PROTOCOL Select a PTZ protocol: PELCO P、PELCO D、MIKAMI or OFF. SPEED Set the PTZ speed from 1~10 TOUR TIME Set the PTZ tour time from 3~30 seconds or OFF. ADDRESS Set the PTZ address from 0~255. BUADRATE Set the PTZ Buadrate: 1200、2400、4800、9600、19200. If this function is activated. 9. If the resolution setting is HIGH. If the resolution setting is HIGHEST. Smart。 Normal mode 1. 2. the total recording frame per second of those 4 channels cannot exceed 60fps in NTSC and 50fps in PAL. If the resolution setting is NORMAL.Menu Operation Front Panel & Remote Controller Mouse Select the Preset Point: 1~20 Zoom + Zoom Focus + Focus Select the PTZ Up/Down Point Select the PTZ Left/Right Point Save the Preset Settings Delete the Preset Point Delete All Preset Points Go to Upper Menu (1)[Enter] to select the preset position [Mouse Scroll Wheel] 1 (2)[Up/Down] for selection (3)[MENU] Exit [CH1] [CH2] [CH3] [CH4] [Up/Down] [Left/Right] [Backward] [Forward] [Stop] [MENU] [Left Click] Z+ [Left Click] Z [Left Click] F+ [Left Click] F [Mouse Scroll Wheel] [Left/Right Click] [Left Click] [Left Click] [Left Click] [Right Click] TILT OPPOSITE ON/OFF: Enable or disable the up/down reversal of PTZ. High. FRAME RATE Set the 『Recording Frame』 and 『Smart Recording Frame』 for each channel. the total recording frame per second of those 4 channels cannot exceed 30fps in NTSC and 25fps in PAL. Highest.【 Record Setup】 RESOLUTION Set the recording resolution: Normal. The max. There are two kinds of mode: Normal. 10 . the total recording frame per second of those 4 channels cannot exceed 120fps in NTSC and 100fps in PAL. recording frame is 30fps in NTSC and 25fps in PAL for each channel. Smart mode 1. the minimum recording frame for each channel is 3fps. RECORD QUALITY Set the record value from 1~10 for each channel. the minimum recording frame for each channel is 1fps. If the resolution setting is NORMAL. the total smart recording frame of those 4 channels cannot exceed 60fps in NTSC and 50fps in PAL. the total smart recording frame of those 4 channels cannot exceed 120fps in NTSC and 100fps in PAL. If the resolution setting is HIGHEST. quality. The max. 2. In normal condition. The higher value is the better 11 . 4. the smart recording mode will start when motion or alarm has been triggered. The recording frame for each channel cannot exceed the smart recording frame. 5. If the resolution setting is NORMAL or HIGH. If the resolution setting is HIGHEST. If the resolution setting is HIGH. smart recording frame is 30fps in NTSC and 25fps in PAL for each channel. the total smart recording frame of those 4 channels cannot exceed 30fps in NTSC and 25fps in PAL. the system will record the footage by using the setting of Normal Mode. 3. 【 Sensor Setup 】 12 . RECORD SCHEDULE Time Table Menu Operation Select Channel Select Time on Time Table Choose the Recording Mode Select “NO RECORD” Select ”NORMAL RECORD” Select ”MOTION RECORD” Select ”SENSOR RECORD” Select ”Motion+Sen sor Record” Front Panel & Remote Controller [CH1] [CH2] [CH3] [CH4] [Quad Display] [Left/Right] [Up/Down] Mouse [Mouse Scroll Wheel] Channel [Moving cursor] [Mouse Scroll Wheel] [Left Click] No Record [Left Click] Normal Record [Left Click] Motion Record [Left Click] Sensor Record [Left Click] Motion+Sensor Record Switch Recording Mode on the Time Table (1)Moving arrow (2)[ENTER] to start selection (3) [Left/Right] to Select time period (4) [ENTER] to confirm or [MENU] co cancel [MENU] On the Time Table，[Drag-Left -Click] Go to Upper Menu [Right Click] 10. ENABLE ON/OFF: enable or disable the motion detection. The number indicates duration of the recording after triggered: 10.30 seconds or OFF. 13 . TYPE Set sensors to NORMAL CLOSE or NORMAL OPEN.30 seconds or OFF. CHANNEL Apply settings to the selected channel (CH1~CH4). The number indicates duration of the alarming after triggered: 1~30 seconds or OFF. SENSITIVITY Set the sensitivity from 1~10. RECORD DURATION BUZZER DURATION ALARM DURATION EVENT POPUP The highest value means the more sensitive. The number indicates duration of the fully display time: 1~30 seconds or OFF. The number indicates duration of the buzzer beeping after triggered: 1~30 seconds or OFF. RECORD DURATION BUZZER DURATION ALARM DURATION EVENT POP UP The number indicates duration of the recording after triggered: 10. 【 Motion Setup 】 CHANNEL Apply settings to the selected channel (CH1~CH4). The number indicates duration of the alarming after triggered: 1~30 seconds or OFF.…. The number indicates duration of the buzzer beeping after triggered: 1~30 seconds or OFF. 15. 15.…. 11. The triggered channel will display in full screen after the motion has been triggered. The number indicates duration of the full screen display after triggered: 1~30 seconds or OFF. MOTION AREA Menu Operation Switch Mode: SET / CLEAR Front Panel & Remote Controller [rewind]/ [Forward] (1)Moving arrow (2)[ENTER] to select area (3)[Up/Down/Left/Right] to select area (4) [ENTER] to confirm or [MENU] to cancel [MENU] Mouse [Mouse Scroll Wheel] Select Motion Area [Drag-Left-Click] Go to Upper Menu [Right Click] 12. 【 Network Setup 】 IP MODE MODE Select IP Mode: STATIC、DHCP。 IP 14 . GATEWAY STATIC: please use the virtual keyboard to enter the gateway IP address. ENABLE ON/OFF: Enable or disable the PPPOE. If the IP mode is set as DHCP. PPPOE SERVER Select the DDNS SERVER: DYNDNS、CCTVDVR or OFF. HOST NAME Please use the virtual keyboard to input the DDNS host name. Please use the virtual keyboard to input the IP address of DNS1. USER NAME Please use the virtual keyboard to input the DDNS user name. the system cannot enter the menu below. DHCP: obtain an NetMask IP address by DHCP server. NETMASK STATIC: please use the virtual keyboard to enter the NetMask IP address. 15 . the system will disable automatically. PASSWORD Please use the virtual keyboard to input the PPPOE password.STATIC: please use virtual keyboard to input IP address DHCP: obtain an IP address by DHCP server. ACCOUNT Please use the virtual keyboard to input the PPPOE account. MTU Please use the virtual keyboard to input the PPPOE MTU。 IP After the PPPOE connection is successfully. PASSWORD Please use the virtual keyboard to input the DDNS password. DNS 1 DNS 2 DDNS Please use the virtual keyboard to input IPaddress of DNS1. it will obtain an IP address automatically. If the IP mode is set as DHCP. DHCP: obtain an gateway IP address by DHCP server PORT Please use the virtual keyboard to input the port number. FROM Please use the virtual keyboard to input the sender’s email address. 13. PASSWORD Please use the virtual keyboard to input the password of mail server. RECORD MUTE ON/OFF: enable or disable the audio record. 【 Audio Setup 】 DVR only supports one audio output. please select “ON” USER NAME Please use the virtual keyboard to input the user name of email server. SERVER Please use the virtual keyboard to input the mail server. CHANNEL Apply settings to the selected channel (CH1~CH4). E-MAIL The email-alert will inform receivers immediately by sending the email. however. SSL ON/OFF: if the SSL connection is nessary on this mail server. Under the quad display. TO Please use the virtual keyboard to input the receiver’s email address. please select “ON”. INPUT VOLUME 16 . AUTHENTICAION ON/OFF: if the authentication is necessary on this mail server. ON/OFF: enable or disable the mute function. under the quad playback mode. ENABLE ON/OFF: Enable or disable the email function. the audio will be disabled. it will output channel one audio. 【 Backup Setup 】 Menu Operation Direction Buttons to Select Item Channel selection Front Panel & Remote Controller [Up/Down] Mouse [Moving Cursor] (1)Select 【CHANNEL】 (1)Select【CHANNEL】 (2) [Left/Right] to (2) [Mouse Scroll Wheel] to select a single select a single channel channel (1)Select 【START】or 【END】 (2) [ENTER] to setup (3) [Left/Right] to select time field. DVD-RW. (4) [Up/Down] to adjust the time value (5) [MENU] to exit settings (1) Select 【START】or 【END】 (2) [Double Left Click] or [Left Click] to setup (3) [Moving Cursor] to select time field. OUTPUT VOLUME 14.Set the value from 1~10. Set the value from 1~10. 17 . (4) [Mouse Scroll Wheel] to adjust time value (5) [Right Click] to exit settings Set the START/END time Calculate the TOTAL SIZE of Backup Enter Backup Operation Go to Upper Menu (1) select the TOTAL (1)Select the TOTAL Size SIZE (2)[ENTER] to calculate (2) [Double Left Click] to calculate [Playback] [MENU] [Left Click]OK [Right Click] Backup Operation Backup device: USB Port (Host). 【 System Setup 】 18 .Menu Operation choose the storage device Start to Backup CD Format(Backup Device: USB) Complete and Exit the Backup Front Panel & Remote Controller [Left/Right] [Enter] [Rewind] [MENU] or [Stop] Mouse [Mouse Scroll Wheel] [Left Click]OK [Left Click] [Right Click] Menu Operation Abort the Backup Front Panel & Remote Controller [MENU] or [Stop] Mouse [Right Click] Menu Operation Exit the Backup Front Panel & Remote Controller [MENU] or [Stop] Mouse [Right Click] 15. . SYSTEM INFO LOG LIST Menu Operation Direction Buttons to Select Item Page Selection Go to Upper Menu Front Panel & Remote Controller [Up/Down] [Left/Right] [MENU] Event Table Record OFF Normal Record Motion Record Sensor Record Manual Record Schedule Record Motion Event Sensor Event Video Loss Network Connection Network Playback Network Download Network PTZ Operation Network Close Hard Disk Overwrite Recovery Shutdown Unknown Error 19 Mouse [Moving Cursor] [Mouse Scroll Wheel] [Right Click] REC OFF NORMAL REC MOTION REC SENSOR REC MANUAL REC SCHEDULE REC MOTION EVENT SENSOR EVENT VIDEO LOSS NET CONNECT NET PLAYBACK NET DOWNLOAD NET PTZ NET CLOSE HD OVERWRITE RECOVERY SHUTDOWN UNKNOWN ERR. ) If the system has set password for admin，the system will ask you to keyin the password before you go into the Quick Menu. WATCHDOG DISK ERROR HD NOT EXIST HD FORMAT ERROR SYS CH1 CH2 CH3 CH4 HD1 HD2 REC ENC DEC Boot Change the Users Configuration Change PTZ Configuration Activate WATCHDOG Disk Error Hard Disk Not Exist Hard Disk Format Error System Channel 1 Channel 2 Channel 3 Channel 4 Hard Disk 1 Hard Disk 2 Record Encode Decode TIME SET The system time setup. (The username and password is for accessing DVR via IE browser. the system will ask whether to chang the time settings or not. Before exit the TIME SET. PTZ CFG.BOOT CHANGED CFG. Menu Operation Direction Buttons to Select Item Front Panel & Remote Controller [Up/Down] Mouse [Moving Cursor] (1) Select [TIME SET] (2) [Double Left Click] or [Left Click] to setup (3) [Moving Cursor] to select time field (4) [Mouse Scroll Wheel] to adjust time value (5) [Right Click] to exit settings (1)Select 【TIME ZONE】 (2) [Mouse Scroll Wheel] to adjust time values [Right Click] 【TIME SET】 (1)Select [TIME SET] (2) [ENTER] to setup (3) [Left/Right]to select time field (4) [Up/Down]to adjust time value (5) [MENU] to exit settings 【TIME ZONE】 Go to Upper Menu (1)Select 【TIME ZONE】 (2) [Left/Right] to adjust time values [MENU] USER MANAGEMENT Set the DVR users and password. 20 . watchdog and no HDD occur. FORMAT HDD Choose the HDD that you want to format. it will not disable the buzzing function whenever the video loss. If the data conflict exists between the both hard discks or time inconsistency is between hard disks and DVR system. motion. sensor. BUZZER BUZZER ENABLE ON/OFF: enable or disable the buzzer beeping. Users are 1~3. The default is ON. it will detect two hard disks. HARD DISK SETUP OVERWRITE ENABLE ON/OFF: Enable or disable buzzer beeping. The default is ON. Front Panel & Remote Mouse Controller Choose the Hard Disk [Left/Right] [Mouse Scroll Wheel] Menu Operation 21 . The default is no password. PASSWORD Please use the virtual keyboard to input password. When this buzzer is set OFF. Note：When the DVR system is activated. TYPE The default is admin. USER NAME Please use the virtual keyboard to input the user name. it will request to format the hard disks. Menu Operation Vertical Position Front Panel & Remote Controller [Up/Down] 22 Mouse [Mouse Scroll Wheel] . FIRMWARE UPGRADE Please download the new firmware and copy to the USB memory stick and then insert the memory stick to the USB port on front panel of DVR. Note: the DVR only can be upgraded by the USB Host. OSD ADJUSTMENT Adjust the OSD position. please select this function. otherwise it will cause serious syste errors. SCREEN BORDER COLOR Border Color: black or white. After upgrading. please don’t operate the system or remove the USB stick while is in upgrading. During the upgrading. the system will ask whether to format the hard disk or not.You Want to Format Go to Upper Menu [Menu] [Right Click] After the hard disk is choosen. After that. the DVR will reboot and restore the sytem as factory default. XGA RESOLUTION Selections of the resolution: 640x480、800x600、1024x768、1280x1024、 1280x720、1440x900 USER CONFIG LOAD SETUP DEFAULT SAVE CONFIG TO USB Decide whether to save configuration into USB or not. Simpilified Chinese. TIME SEARCH Menu Operation Front Panel & Remote Controller Mouse 23 . Default status is OFF.Adjustment Horizontal Position Adjustment Go to Upper Menu [Left/Right] [MENU] [Left Click] [Right Click] [Middle Click] AUTO SWITCHING Switching Invterval: 1~10 seconds or OFF. 【 Search Setup 】 The DVR has two kinds of search method : Time Search、Event Search. Traditional Chinese. LANGUAGE OSD Language Selection: English. 16. (3) [Mouse Scroll Wheel] to adjust time value (4) [Right Click] to exit settings [Left Click]OK [Right Click] Search & Playback Go to Upper Menu [Playback] [MENU] EVENT SEARCH Menu Operation Selected Event Selected Page Search & Playback Go to Upper Menu Front Panel & Remote Controller [Up/Down] [Left/Right] [Playback] [MENU] Mouse [Moving Cursor] [Mouse Scroll Wheel] [Double Left Click] [Right Click] Playback Operation 24 .Time Set of “SEARCH” (1) [ENTER] to setup (2) [Left/Right] to select time field. (3) [Up/Down] to adjust time value (4) [MENU] to exit settings (1)[Double Left Click] or [Left Click] to setup (2) [Moving Cursor] to select time field. Menu Operation Rewind Fast Forward Rewind one Frame Forward one Frame Normal Playback 1x Pause Fast Forward Time Set of Backup CH1 Display CH2 Display CH3 Display CH4 Display Quad Display Front Panel & Remote Controller [Rewind] [Forward] [Left] [Right] [Playback] [Pause] [Stop] [Enter] [CH1] [CH2] [CH3] [CH4] [Quad] Mouse [Left Click] [Left Click] [Left Click] [Left Click] [Left Click] [Left Click] [Left Click] | | [Left Click] Double Left Click on the CH1 Double Left Click on the CH2 Double Left Click on the CH3 Double Left Click on the CH4 Double Left Click on the full screen Time Set of Backup 25 . MANUAL RECORD 18. 【 Cell phone monitoring 】 Cell phone supporting Java Script. For example: http://xxx. 17. Channels are set as motion record and not in the triggering.xxx.Menu Operation “START” time setup “END” time setup Enter the Backup Operation Back to Playback Operation Rewind Fast Forward Rewind in one Frame Forward in one Frame Normal Playback Pause Front Panel & Remote Controller [Up] [Down] [Enter] [MENU] [Rewind] [Forward] [Left] [Right] [Playback] [Pause] Mouse [Left Click] [Left Click] [Left Click] [Right Click] [Left Click] [Left Click] [Left Click] [Left Click] [Left Click] [Left Click] | | Stop Playback [Stop] [Left Click] * Time search is not supported during fast forward or rewind on a single image playback. 【 Other Function 】 The manual record will active the below channels to record: 1. Channels are set as seneor record and not in the triggering.html?delay=5 26 . Channels are not in recording mode. The manual record will be listed on the LOG LIST. please use http://xxx.html Entering username and password on the same page for internet connectivity. 3. please add “delay”ranging from 1~9.xxx/idx_js. 2. please use http://xxx.xxx. In the environment of lesser bandwidth or slow internet speed.xxx.xxx/idx.xxx/idx.html Monitoring on an older model of cell phone or cell phone with less functions. 【 AVPlayer Operation 】 Preface AVPlayer can playback the record files which backup via DVR. System Requirement OS：Windows 2000、XP、Vista. Then. Note: If the system doesn’t install the program automatically.bat” in the directory of storage device User Interface 27 . if it has already installed the AVPlayer previously. the system will ask whether to replace the old program or not. Obtain and Install Program While backup the record files via DVR. please execute the “run. Please click to install. After complete the installation.19. the system will execute the AVPlayer. the system will automatically copy the files and the software to the storage device. the system will ask whether to install the program or not. Then. when you open the storage device. System Requirement OS：Windows 2000、XP、Vista. the default ID and Password are admin and empty respectively. playback records. the system will ask the ID and password before login. and backup datas. Web Browser：Internet Explorer Install Add-ons When you access DVR via IE browser. If you were the first time to enter the web page. 【 Web Operation 】 Preface The remote accessing via network allows you to monitor the DVR.Open File Fast Rewind Rewind 1x Pause Playback 1x Fast Forward Capture the Image (Snap Shot) to the Local Computer Volume Control Minimize Window Exit Click Click Click Click Click Click Click Drag Click Click Use the right click on mouse to open the pop-up menu as below: Open Pop-Up Menu Open files Set the snap shot file path Set the language Exit the program 20. please input the ID and password of the DVR. the browser will ask you to install the add-ons： 28 . Then. Choose to install add-ons： User Interface Live 29 . click to enable the audio or click to disable；under the quad display. CH3 full screen display.Play/Stop Live View Record to the Local Computer Snapshot image to local computer Enable or disable audio CH1 full screen display. 32X) to snapshot image (Please set the save Click path in the 『SETTING/INFO』) Click disable. 4X. Quad display Click to start/stop record(Please set the save Click path in the 『SETTING/INFO』) Click to snapsnot image (Please set the save path in the 『SETTING/INFO』) Under the live view. Click Click Click Click Click Playback Start to play video Pause/Play Stop playing Fast Rewind Fast Forward Snapshot image to local computer Enable or disable audio (1) Click (2) Click Click Click to select the video (. 16X. to playack the video Click (Multiple speed 2X. it doesn’t offer the sound effect. 32X) Click (Multiple speed 2X. 8X. CH4 full screen display. 4X.av). 16X. CH2 full screen display. 30 to enable audio and click to . 8X. to snapsnot image (Please set the save path 31 . of search (2) Click (3) Click of search (4) Click to play video or click to save files to the local computer (Please set the save path in the 『SETTING/INFO』) to search video records (1)Click (2)Choose the event type and channel (3)Click to list all events to change page (4)Click (5)Select events from the lsit (6)Click to playback the video record or click to save files to the local computer(Please set the save path in the 『SETTING/INFO』) Click Click Click Click Event Search Pause/Play Stop playing Enable or disable audio Snapshot image to local to enable audio and click to disable. Search Time Search (1) Click to search record files. computer in the 『SETTING/INFO』) PTZ Select the PTZ channels Select preset 1~20 Zoom + Zoom Focus + Focus Set the PTZ position (Up/ Down/ Left/ Right) Start/Stop the Auto Tour Play/Stop PTZ video Record the PTZ video to the local computer Snapshot the PTZ image to the local computer Enable or disable Audio Click Click Click Click Click Click Click to select preset points Click Click Click to start/stop record (Please set the save path in the 『SETTING/INFO』) Click to snapsnot image (Please set the save path in the 『SETTING/INFO』) to enable audio or click to disable the Click audio Setting / Info 32 . 0.95.0 OFF PPPOE DDNS Port DNS1 DNS2 Server Host Name User Name Password Enable Account Password MTU 1492 OFF 1’st Menu 2’st Menu 3’st Menu Network IP Mode Mode IP Netmask Gateway Default STATIC 192.1.192.100 255.95.0.1 80 168.168. to save 21. 1’st Menu 【 Default Setting 】 2’st Menu 3’st Menu Channel Title Display Brightness Contrast Hue Saturation Default 1 CH1 ON 25 25 25 25 1 second 1 second Type Protocol Address Buadrate PTZ Speed Tour Time Preset Tilt oppos ite OFF OFF 1 9600 5 OFF 1 OFF 1 High 33 EMAIL IP Enable Server 0.1 168.0.168.1 OFF Loss Buzzer Duration Camera Loss Alarm Duration Record Channel Resolution .255.255.0 192.0.SnapSot Save Path Video Save Path Download the User Manua Type a path in the text box then click type a path in the text box then click Click to download to save. Mode Frame Rate CH1 CH2 CH3 CH4 CH1 Record Quality CH2 CH3 CH4 Record Schedule Channel Type Record Duration Buzzer Duration Alarm Duration Event POP-UP Channel Enable Sensitivity Record Duration Buzzer Duration Alarm Duration Event Popup Motion Area Normal Record 5 FPS 5 FPS 5 FPS 5 FPS 8 8 8 8 Normal Record 1 Normal Open 5 seconds 1 second 1 second Audio OFF 1 OFF 5 5 seconds 1 second 1 second OFF Non System Backup Input Volume Output Volume Channel Star End System Info Log List Time Set Mute Channel Record From(Send er) To (Receiver) Authenticat ion OFF SSL User Name Password OFF 1 OFF Sensor OFF 5 5 1 Motion Time Set Time Zone GMT+08 Admin ON ON Type User Manageme User Name nt Passward Buzzer Hard Disk Setup F/W Upgrade Screen 34 Border Color Enable Overwrite Enable Format HDD White . Auto Switching OFF Recording Results NTSC FPS setting Recording Mode HIGHEST (D1) 30 FPS 204 336 25 FPS 256 358 15 FPS 408 672 10 FPS 640 895 5 FPS 1224 2016 5 FPS 1280 1790 HIGH (Half D1) 60 FPS 238 392 50 FPS 278 386 30 FPS 476 784 25 FPS 556 772 10 FPS 1428 2352 10 FPS 1390 1930 NORMAL (CIF) 120 FPS 236 388 100 FPS 330 460 60 FPS 472 776 50 FPS 660 920 20 FPS 1416 2328 25 FPS 1320 1840 Full-time recording 25%on motion recording FPS setting PAL Recording Mode Full-time recording 25%on motion recording XGA Resolution OSD Adjustment (Vertical. 【 Recording Time Table 】 Recording Quality: Value 8) (Time Unit :hour 【 USB Compatibility 】 SanDisk Brand SanDisk Transcend SanDisk Transcend Kingston Transcend Kingston Adata Kingston Adata Adata Adata SONY SONY 4G Capacity 8G 4G 16G 16G 4G 32G 8G 4G 16G 8G 16G 32G 8G 16G 35 Cruzer Micro MODEL Cruzer Micro Jetflash V20 Cruzer Micro Jetflash V30 DTIG2 Jetflash V20 DTIG2 PD1 DTIG2 PD1 C801 C801 Microvault Microvault . 23. 1(1) ] User Config Language English 22. Horizontal) Load Setup Default Save Config to USB 800x600 [ 3(5). 36 . 37 H12C646001 .