Flowserve_VOGT_01

Vogt ValvesCatalog and Application Manual Vogt Valves VVACT0000 Third Edition Flow Control Division Vogt Valves Forged Steel Valves and Fittings Page Index by Valve Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - v Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3 Description of No. System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gate Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 43 Nuclear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Sour Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Globe Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 - 87 Auxiliary Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Check Valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 - 111 Engineering Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 - 123 Fittings & Unions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 - 132 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Glossary, Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . 134 - 136 Care & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 137 - 139 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 - 143 Standards, Data, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . 144 - 149 Flow Control Division Vogt Valves Gate Valve Index Press. Class 150 Material A105 Bonnet Joint Bolted 300 A182 F316/F316 L A350 LF2 A105 Bolted Bolted Bolted 600 A182 F316/F316 L A350 LF2 A105 Bolted Bolted Bolted A182 F316/F316 L A350 LF2 Bolted Bolted End Connection Flanged Butt Weld THd/SW Flanged Flanged Flanged Butt Weld Thd/SW Flanged Flanged Flanged Butt Weld Thd/SW Flanged Flanged Threaded Socket Weld Bolted Male Thd x Fem Thd Male Soc x Fem Thd Male Cpt x Fem Thd Threaded A105 Socket Weld Weld Male Thd x Fem Thd Union 800 A350 LF2 Bolted Bolted A182 F3/F316L Weld Union A182 F316H Bolted A182 F5 Bolted A182 F9 Bolted Male Soc x Fem Thd Male Cpt x Fem Thd Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Male Thd x Fem Thd Male Soc x Fem Thd Male Cpt x Fem Thd Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld i Bonnet Type OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y ISS OS&Y ISS OS&Y OS&Y OS&Y OS&Y ISS OS&Y ISS OS&Y ISS OS&Y OS&Y ISS ISS OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y ISS ISS OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y SERIES 353 BW353 See Class 800 358 32353 363 BW363 See Class 800 368 32363 373, 13373, 11403 BW373 See Class 800 378 32373 12111, 13111, 11103 12161 SW12111, SW13111, SW11103 SW12161 TT12111 ST 12111 CT12111 2801, 2801B 2811 SW2801, SW2801B SW2811 TT2801 TT2811 ST2801 CT 2801, CT 2901 59851 SW59851 32111 SW32111 12401, 13401 SW12401, SW13401 2831 SW2831 TT2831 ST2831 CT2831 59951 SW59951 82401 SW82401 12421 SW12421 12921 SW12921 483B. Class 800 (cont. 10403 See Class 800 32493 12141. 22141 12443. CL. SW1971 SW12181 TT12141 ST 12141 CT12141 2821. 1043 SW15111. 810 SW2821. SW1043. SW1033 15373. 16111. 11683 15801 SW15801 ST15801 35111 SW35111 15401 SW15401 15831 SW15831 15321 SW15321 66703 SW66703 66713 SW66713 SW66773 SERIES 473. CL2 Welded A182 F22. 13141. 12141B.3 Welded End Connection Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Flanged Threaded Socket Weld Male Cpt x Fem Thd Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Socket Weld End Connection Flanged THd/SW Flanged Flanged Thd/SW Flanged Flanged Bonnet Type OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y Thd/SW Flanged OS&Y OS&Y OS&Y Bolted A105 Weld 1500 A350 LF2 Bolted A182 F316/F316L Bolted Weld 2500 Vogt Valves (cont. SW13141 SW22141. 1033. CL2 Bonnet Joint Bolted A182 F22 CL 3 Bolted A182 F11. 22493MT. 12141B.Flow Control Division Gate Valve Index Press.) Bonnet Type OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y SERIES 12321 SW12321 12521 SW12521 15111. 22483CL See Class 800 32483 493. SW16111. Class 150 Material A105 300 A350 LF2 A105 600 A350 LF2 A105 Bonnet Joint Bolted Bolted Bolted Bolted Bolted Bolted Bolted A350 LF2 Bolted Bolted 800 Threaded ISS Bolted A105 Weld Socket Weld OS&Y Male Thd x Fem Thd Male Soc x Fem Thd Male Cpt x Fem Thd Threaded Socket Weld ISS OS&Y OS&Y OS&Y OS&Y OS&Y ii .) Material A182 F11. SW810 Globe Valve Index Press. 22461. 1971 12181 SW12141. SW22461 SW10103.2 Bolted A105 Welded A182 F11. SW12443. 10103. 473B See Class 800 32473 483. 11603. CL. 22493CL. 493B. SW1003. 3 Weld A105 Weld A182 F11.Flow Control Division Globe Valve Index Press. CL. CL. 1522 SW1522 66723 SW66723 66733 SW66733 66793 SW66793 2510 SW2510 2511 SW2511 2522 SW2522 . SW15443. 3 Weld iii Vogt Valves (cont. CL2 Weld A182 F22. CL. 1023 SW15141. CL2 Weld A182 F22. CL2 Bolted A105 Weld A182 F11. SW1023 15493. 10683 15821 SW15821 15501 SW15501 15351 SW15351 1510 SW1510 1511 SW1511. CL.) SERIES 801 851 SW801 SW851 12501 SW12501 82501 SW82501 SW12351 811 SW811 12551 822 SW822 32141 SW32141 15141.) Material Bonnet Joint End Connection Threaded Threaded Socket Weld Threaded Socket Weld Socket Weld Threaded Socket Weld Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Bonnet Type OS&Y ISS OS&Y ISS OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y Flanged Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y OS&Y Union Socket Weld A182 F316/F316L Bolted A182 F316H Bolted A182 F11. CL. 3 Weld A105 Weld A182 F11. Class 800 (cont. 10603. 3 Bolted Weld A350 LF2 Bolted Bolted A105 Weld 1500 1690 2500 2680 A182 F316/F316L Bolted A182 F11. 1003. CL2 Weld A182 F22. 2 Bolted Weld A182 F22. 15443. SW710. CL.B710 4835. SW5483 718 SW718 S718 SWS718 B718 SWB718 54863 82718 SW82718 32701 SW32701 15701 B15701 SW15701 SWB15701 15593 1610 SW1610 1622 SW1622 2610 SW2610 2611 SW2611 2622 SW2622 . 54853 SW9091 SWB9091.701ZL.Flow Control Division Vogt Valves Check Valve Index Press. CL. SWS701 S74 SWS74 9091 B9091. 3 Weld 1690 2680 Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Flanged Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld iv Type Piston Piston Swing Piston Piston Piston Swing Piston Piston Piston Swing Piston Piston Ball Swing Piston Ball Swing Swing Swing Piston Ball Piston Ball Piston Piston Swing Swing Ball Ball Ball piston Piston Piston Piston Piston Ball Piston Ball Piston Piston Piston Piston Piston Piston Piston Piston Piston Piston Piston SERIES 573 See Class 800 S 673 32573 583 See Class 800 S 683 32583 593 See Class 800 S 693 32593 701. SWB710 SW4835. CL. 2 Weld A182 F22.710. 3 Weld A105 Weld A182 F11. S701 SW701. Class 150 Material A105 300 A350 LF2 A105 600 A350 LF2 A105 A350 LF2 Bonnet Joint Bolted Bolted Bolted Bolted Bolted Bolted Bolted Bolted Bolted Bolted Bolted Bolted End Connection Flanged Thd/SW Flanged Flanged Flanged Thd/Sw Flanged Flanged Flanged Thd/SW Flanged Flanged Threaded Socket Weld A105 800 No Threaded Socket Weld Threaded Union Socket Weld 1500 A182 F316/F316L Bolted A182 F316H Union Bolted A350 LF2 Bolted A105 Bolted A105 Weld A182 F22.SW13701 SWB701.13701 B701. 9841T SW9871T. 1881T. SW9841T 98717T. 9841T SW9871T. Class 3000 Material A105 Bonnet Joint Screw 6000 A105 Screw v . SW9841T 9821T SW9821T 3991T SW3991T End Connection Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Bonnet Type Piston Piston Ball Ball Piston Piston SERIES 1551. 2891T SW1871T. SW9841T 9871T. 9841T SW9871T. SW1331T. SW2891T 54831T SW54381T 9871T.Flow Control Division Vogt Valves Meter Globe Valve Index Press. 2191 SW1551. SW2191 B1551 SWB1551 4881 SW4881 Hydraulic Check Valve Index Press. Class 3000 Material A105 Bonnet Joint Screw 4000 A105 Union 5000 A105 Screw A182 F316/F316L Screw A182 F316/F316L Screw A182 F316/F316L Screw A105 Screw 6000 End Connection Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Threaded Socket Weld Bonnet Type ISS ISS ISS ISS ISS ISS ISS ISS ISS ISS ISS ISS ISS ISS SERIES 1331T. trims and bonnet configurations. Vogt’s leadership has been evident in the production of forged steel fittings. For more than 100 years.Flow Control Division Vogt Valves – A History in the Making Vogt Valves Vogt Valves. angle and check valves in most popular materials. IN In the late 1890s. This business. Vogt Valves supports a worldwide network of distributors with access to the world’s largest capability for the manufacturing of forged steel valves and fittings. vi . Jeffersonville. Vogt pioneered the early development of ammonia absorption refrigeration systems that made artificial ice. globe. gate. plus Vogt’s fledgling boiler business created an internal need for quality valves that initiated Vogt’s early entry into the valve manufacturing business. Today. The early reputation of Vogt’s quality valves and the rapidly growing petroleum processing industry created an outside demand that would firmly establish Vogt in the mass production of high quality forged steel valves. ............... 18....................... 41 13................................ Page Nos...119 Materials (General Use) ......... 21 6-8...............89-111 Engineering Tables ..................................................44 Sour Service............................................................................................88 Standards for Valve & Fitting Industry ................. 80-82 ..............112-123 Fittings & Unions .............................................. MB8 and MBS suffixes meet NACE.. Angle and Check Valves can be provided with appropriate trim materials for sour service............................................................................ Gate Valves 7.... 11............................................... 76 83-87 45 44 68.........................2-3 Description of No................. Pressure & Temperature .......... Cross Reference ....124-132 Spare Parts ........................................................126 Pressure-Temperature Service Ratings....... 54........................ Valve series with MB6..................................... Gr.......................................................118 Materials (Valve Trim).................................... See pages 4 and 45 for explanation........................... 52 50................................117 Series Number Index .... 108 100 * GIobe.................................................... 17 109-111 45 44 107............................................................ System .................137-139 Limited Warranty ...................................................... LF2 ( to -50°F) API-600 Wall Thicknesses Extended Body Bellowseal Chlorine Cryogenic (to -325°F) F316...............134 Replacement Parts......................................................................................... 64................145-146 Materials (Forging) ............... 9...................119 Packaging Data for Fittings ...................................................................................................................133 Conversions: Weight...................................................... 61 57 63.................... 59 47-49........................................................................... 55 51................... F316L Flow Control Hydraulic (NACE MR-01-75) Sour Service * Nuclear Y-Pattern Zero Leakage Check Valves 93........................... 35.................... 97 90-92..........................................................112-115 Auxiliary Operators..................... 33... 43 10....144 Cv Factors .........45 Globe Valves ............................. 14........................................................ 36 25-29................................. 4 Gate Valves.................................................................................... Glossary of...122-123 Valve Packing Materials ............................................. i-v Index ......5-43 Nuclear ..................................................... 1 45 44 Globe Valves 53........ 12.......148-149 Thread & Socket Weld Standards.... 38........................................................................................... 73 62 47-49.............................. 46-87 Check Valves .............................................................................135-136 Care & Maintenance of Vogt Valves ..................120-121 Abbreviations & Terms Used in the Valve & Fitting Industry..................... 99 94 PAGE NOS.............Flow Control Division Vogt Valves Table of Contents Catalog Sections Page Nos................ 22...................................... Index by Valve Type...................................140-143 Cv Formulas.................................................................................... 78............................................... 71........................................... 20............................................ 72..138 ASTM Material Specs....................... 55.......................116 Service Application Alkylation (HF) ASTM A350...........................................2-3 Dimensional Data for Standard & Schedule Pipe ................................................. 126...............26 ST 2801F8M...............127 2801..........................111 5061............14 12111 .108 2622.........100 701.126-128 SW 2324................................................................................31 2811FHF ......31 TT 2811 ......................................107 SW 1610................126..8 373FHF..................................................................127................109 SW 1551.....7 363FHF..26 ST 2801FHF..............26 ST 2801MB6 ..126-128 SW 229 ..............127........ Series No..............80 SW 1522........26 TT 2801.99 718T................................................71 10403.......107 1622........................................7 BW 363........8 373MB8 .........81 SWR 2511 ................24 2801MM.......................14 12111FHF ...........27 12111 ..........................125 6281................127..................6 363.............................................94 SW 4835....... Page No.....65 1003......8 BW 373MM..20 368............................126-128 SW 4200.....90 573F8M....126..................26 2811 .........................................47 473MB8 .......126.................48 483MB8 ................8 373MM..............97 718................................95C 701.100 701MBS ..................126..............................126-128 SW 4823.......126-128 1280..........127 1971................. 573MB8 .................90 573MM........108 SW 2622.........25 CS 2901..........130 243....................98 710............. 97 710.......... SW 2801..............126.........................126..91 593.............99 718....................67 SW 2821FHF.............127..... 4200...............8 473.....82 SW 2522..........126-128 SW 1211 .127............................100 701MM...96 SWS 74 ...................126-128 1510.................24 2801FHF...........14 12111MB6 .........100 701ZLB .......................127...................70 SW 851....98 710FHF........... 1951..72 11103 .............................132 SW 1931......................................................30 TT 2831..68 SW 822................126-128 SW 1399...24 SW 2801MBS ................7 353FHF....................................126.......................................................................127.................................36 SW 1043..............47 473MM..............24 TSW 2801FHF.................6 BW 363F8M........110 2199..92 593MM....20 353T.......................95A 683 .........100 701ZLE ..................... Page No.........................91 583F8M...127...31 TSW 2811 .............................127 1800.........................26 ST 2801......................130 673 .......100 701MB8 ...................................126....26 SS 2801MB6 ..... Series No.......24 SW 2801MM..............126...47 473B ..24 2801MB8 .......49 493B ....................130 4835..............99 801..........126-128 1871T.92 593F8M.............................14 12111 ...126-128 1610.............86 SW 9871T......104 SWB 9091.............126-128 353.....36 2001..........104 B 9091...................126-128 SW 2110 .....................................................20 BW 373R .95B 693 .........84 SW 2891T.......................26 2821....................80 1522.......24 SW 2801MB6 ..130 SWT 1211 ...........19 12111ER ...........83 1399.............................69 810...126....90 583....................20 BW 363R ..126-128 SW 1160 ..........95 701F8M................107 SW 1622.96 229.................80 SW 1511 .126..130 2024...126-128 SW 2001........................................................................33 11403 ........................ Page No.....26 2831T...............................126-128 2450.....................................109 SWB 1551..92 593MBS .....127 SW 2024....127...........86 10103..........78 R 1511 .............................100 701ZLN ...........................97 701HF7 .67 2821F8M........25 ST 2831............................................100 701MB8 ...68 SW 810...............................................................24 SW 2801F8M.....................................83 1899......98 710FHF....................................130 1260.............................26 2891T.27 12111 ...126.........................130 1189....................................127..............................................126.127..........................................................83 SW 1871T....................................95 718T......................71 SW 10103...............35 BS BT CT ST SW TSW TT ST SW SW TT SW SW SW SW ST 12111 ..........126..130 Series No....................73 1023............................7 363MM .48 483B ..87 4001...109 2400...............................126-128...78 R 1510........127 SW 1299.....................126-128 SW 243 .....................28 .............126...............91 583MB8 ....19 12111F8M ....125 1331T.......91 583MM..14 12111MB6 .........100 701MBS .73 SW 1003.........81 R 2511 ..........80 1511 .............130 573........14 12111FHF .....49 493MB8 ...........14 12111HF6 ....130 2510..................48 493...................13 2801F8M...................................86 9871T................................126-128 273...47 473F8M.14 12111HF7 ....Flow Control Division Vogt Valves Index Series No...98 710....................................7 BW 363MM.47 483............................................127.......126.24 2801B ...........14 12111MM ............27 12111 .....25 SS 2801..........................26 ST 2801MB8 .......130 SW 2350.........................111 SW 4881 ..........98 718.............................127 2370.......................................99 718......128 SW 2670....95 701.126...............................107 2610...................31 SW 2811FHF ................................6 353MB8 ....................25 3991T.......................126......................................130 2324.....................36 SW 1033.........125 9091..........................20 BW 353R ........................132 SW 1961.....80 1551.............................130 2271.....126-128 2110.......................108 2611 ..126-128 SW 2450.....67 2821FHF...78 R 1522..................132 SW 1951..24 TSW 2801..........82 2560........126-128.91 583MBS .............104 SW 9091........126.....................68 822..130 2350....49 493MM..............................126......110 SW 2191 ..67 2831.................................7 363R .....128...........6 353MM........95 718...............................100 701ZLV ..24 2 Series No.........82 2511 ....108 SW 2611 ...........31 SW 2811 ...........8 373R ....................72 10683.......68 Series No......................................28 12111ER .............127..........................26 TT 2801F8M...14 12111 ................108 SW 2610.......81 R 2510.................126-128 SW 2090..100 701MM...............10 11603 ...6 358.........49 SW 503...................126-128 SW 4001..........130 1211.....................................29 12111ER ................86 SW 9841T.........82 SW 2511 ........................130 259....97 701..20 378....126.........68 811 ........90 573MBS .126.................130 1931...130 SWT 1160 .............8 373F8M......................................................127....126-128 1299......108 2670.......25 CT 2901..............................70 Page No..........30 CT 2831..........132 1961.........................125 SW 2271..........49 493F8M.......33 SW 11103 ....25 CT 2911 ...81 SWR 2510.13 SW 2801B ............24 SW 2801FHF......................................................86 SW 9821T...... S 74.........24 CT 2801.................................................126-128 2580.........78 SWR 1522.24 2801MBS ......127......68 SW 811 .........14 12111F8M .14 12111MM .................126-128 SW 2199.87 SW 3991T.........8 BW 373F8M...................126-128..............................................................126........130 2090.......................................82 SW 2510................. 851.94 4881 ...............80 SW 1510..................6 353R ....126...........127.......................29 12111FHF .........................100 701F8M.........73 1033........................................84 BT 2901...........35 11683 ...... Page No.....128..................65 SW 1971..127...........6 BW 353.......92 623.....81 R 2522..........83 SW 1331T.6 353F8M .......97 718.........48 483MM.127 SW 1899.................127.............36 1043.....78 SWR 1510................7 363MB8 .....................67 SW 2821F8M...............130 1160...........................................67 SW 2821............................26 ST 2801MM.....69 SW 801...78 SWR 1511 ......100 701................127.......86 9841T......................82 2522..................................104 9821T...............73 SW 1023...................................109 B 1551.81 SWR 2522.................90 SW S S S S SW SWS SW SW SW SW B SWB SWB SWB B SW SWB SW B S SW SWB SWS SW Page No............25 BT 2901MB6 ....100 701...........130 4823........26 TT 2801MM....126-128........92 593MB8 .....................24 SW 2801MB8 .................................126...................................................................130 2130..............48 483F8M.97 701HF6 ........................126..........98 710...........126..........................................................................................51 10603...............24 2801MB6 ..28 12111 ................................8 BW 373..126-128 2191 ............................................7 373 ................. 99 32701MB8 .........37 15111F8M ..................18 32111MB8.......75 15351.15 12401..103 58431T...........59 SW 23141HF5 ..............61 SW 22141CL .............50 SW 23141HF4 ...18.............................................23 12161...18 32111F8M ..............63 SW 12443....................................37 SW 15111FHF .................................................93 SWB 43721HF4 ...16 SW SW SW SW SW SW SW SW SW SW SW SW SW SW 12921..6 32363......7 13401......77 15821FHF........Flow Control Division Vogt Valves Series No.....56 82718............54 42241MTG...........................39 22461...................................................................................................32 SW 59851MBS ............37 SW 15111 .........................9 13373MMP ..................................................................21 13111MB8 ..........90 32583.......75 15141MBS ................40 SW 15831...............41 15801FHF............75 15501FHF.......19 42211MTG ...................................................................................23 12161F8M.....55 12141HF6 ...........16 12921...16 12921FHF...................................40 15821.14 SW 12111MMT ...........58 13141FHF......38.............56 12401.............16 SW 12421FHF.......58 13363MMP ..14 12111R........64 15501......................... 43 32111MM ......... SW 35111F8M ........75 15141MB6 ...11 SW 42211MTG .... 32353....74 15493FHF..............34 15373....42 66773...........32 59851MBS ......75 15141.16 12443............21 13111FHF ......14 SW 12111T ............ SW 12111MB6 ..........74 15493MBS ........................56 SW 12551FHF...15 82501.99 SW 32701.....66 12321..60 22141MM..........21 13401.........37 15111MBS .............................................. 35111MB8...77 SW 15821MBS ................38..............75 15141FHF...79 66723.55 12141MM................................21 13111 .............................21 13111F8M ...............55 12141T.102 13701.................77 15821MBS ...................77 SW 15821MB6 ....40 15801F8M...........23 12181..........18.......29 12111MB8 ...........40 SW SW SW 3 32111 ............103 54863..77 SW 15821MM..... 43 32111MM ...........................64 22461FHF......62 12141...........40 15801FHF....106 15701FHF.....................38................53 SWB 43721HF2 ............................75 15321...............91 32593.....................32 59851F8M......105 SW 15593FHF........64 SW 22461........21 13111HF5 ....................59 15701........23 12161MM................16 12321FHF.......18.......75 15141F8M.........................40 15801MB8 .............................18 32141.74 22141CL .................77 15821F8M.......... 66703.................75 SW 15501FHF...........................55 12141MB8 ...21 13701.21 13111FHF .........................................18 32111 ..................40 15801MB8 ....56 12521...........37 SW 15111F8M ......37 SW 15401.........................21 13111F8M .......85 SW 58431T........... Page No.............................................21 13111MM ...........92 32701.....17 12401C .................39 SW 16111 .......55 12141T.61 SW SW SW SW SW SW SW SW SW RJ RJ 16111 .......................................................74 15493MM.......................... SW 12421.......76 SW 15443......... Page No.....57 12501T.........75 15141MB8 .34 15373FHF....23 12161F8M....................58 13141FHF...........................................79 66733........16 12351.........99 ..55 12141B ......93 SWB 43721HF5 ....50 22493MT....75 15141MB8 ..................64 SW 22461FHF...............................77 SW 15821FHF.......58 13141.......................... SW 35111 .........62 12141....42 66713.......32 SW 59851....77 15821MM...........19 06....99 SW 82718..37 15321...27 CT 12111MB8 ........37 15111MB8 ..................................27 ST 12111MB8 ...........99 35111 .........................................40 15801MM...................................106 B 15701...............................................61 22141F8M...............................................66 12181....23 12161MM..............16 12551..37 Series No......32 59851MM.79 66793......57 SW 12501C .......15 12421......60 SW 22141F8M........55 32141..................42 66713..16 12421FHF......37 SW 15111MB6 .................. Page No.....77 SW 15821MB8 .....................34 SW 15801MBS .............55 12141HF7 ...22 13111R..................7 13373..........74 15493MB8 ...7 32373...50 22493CL ......................79 66733.........................49 32573.................62 12141FHF....75 15141MBS ...............................55 32141MB8 ...................56 SW 82501...................................................37 SW 15111MBS . 43 32111 ........15 12401C ........................37 15111FHF .......................34 15373FHF......54 43111MMP .............32 SW 59851MM.......................................... Page No........................37 SW 15111MB8 ..32 SW 59851F8M...74 15493MB6 .......22 SW 12111R...................99 SW 32701MB8 .....................14 SW SW SW SW SW SW CT ST TT SW SW SW SW SW SW SW SW SW SW SW SW SW SW 12141..................8 32373MB8 .....................52 12141B ......... 43 32111MB8........18...................................16 SW 12521............. 43 32111F8M ........40 15801.17 12401FHF..............63 12501..............................................77 15821MB6 .....56 SW 12501... Series No.21 13111BB .......18..............40 SW 15801MM.......105 22483CL .......15 12401FHF.........................106 ST SW ST SW SW SW TSW SW TSW SW SW 15801....56 12501C ......14 TT 12111MB6 ..............................................................15 12401T.. Page No... 15141..42 66723.....................55 Series No..............32 59951..........37 15443..............................32 59951T.......60 22141MT..14 12111MMT ......................11 43241MMP .........................................................47 32483................................77 SW 15821..........48 32493.......19 08......105 SW 15593..............75 SW 15501..54 SW 42241MTG..93 54853...........55 12141..............40 15801MBS ........................................ 41000 41000 41000 41000 43 43 43 43 43 43 04.....19 09..................75 15141MM.........14 SW 12111MBS .................102 15111 ...28 SW 12111MB8 .................................................16 12321.........77 SW 15821F8M.........16 SW 12521FHF.......11 SW 42241HF2 ...........................................75 15373....14 12111MBS ..61 SW 22141MT....................79 82401....................75 15141MB6 ........16 Series No.........38.................55 12161............................7 32363MB8 .............22 12111T ......................................55 12141MB8 ........................................16 12321FHF.............. 43 32111F8M ................................12 SW 43211HF2 ........................55 12141........................105 15593FHF.....16 12521FHF......106 SW 15701FHF.55 32141F8M....................................55 12141FHF.....75 15593...........53 43241MTP ................38............75 15141F8M........55 12141MM....41 15801.............................6 32353MB8 ......75 15141MM.....................77 15831........................55 32141MB8 ...37 15111MB6 ........16 13111 .........15 82401FHF... SW 35111MB8...........14 BT 12111MB8 ....................55 32141F8M...37 15351.42 66703.........................................18.55 12141F8M.........................60 SW 22141MM........................38.....................16 12921FHF.......8 32473................103 SW 54853.............32 Series No.............................. SW SW SW SW SW SW Page No........21 13111R..................................40 15401..............................56 SW 12551...52 12141F8M.............75 15141FHF.22 13141..................77 15821MB8 ....... 35111F8M .15 12401T.........................21 13111HF4 .........................15 SW 82401.......106 SW 15701..................56 SW 12501T.....42 66793.............106 SWB 15701........56 12351..................................76 15493..........79 66773.........................74 15493F8M.........85 59851.............. a few design features have also been used as part of the prefix including S. Prefix Description: (Blank) .Socket Weld SWB .Swing Check (SW) TS . A fully female threaded valve as the traditional Vogt standard does not have a prefix number (see below for prefix descriptions). A182-F5.) and pressure boundary material of construction (A105.Butt Weld CS . B and ER. check.Swing Check (female NPT) SS .) 4 (Blank) – Standard Trim B – Bellows Valve C – Cryogenic Valve CL – Chlorine Valve Trim – Monel/Hastelloy ER – Emissions Reduction – Double Packed with Lantern Ring F8M– 316 Trim FHF – Full Hard Face (unless standard) FH8 – Full Hard Faced F8M Trim FHT – Teflon Packing and Full Hard Face HF – Hard Faced Disc (F316 Globes and Checks Only) HF2 – UOP Alkylation HF4 – UOP Alkylation HF5 – UOP Alkylation HF6 – UOP Alkylation HF7 – UOP Alkylation L – Locking Device MB6 – 13% Chrome Trim – NACE MB8 – 316 Trim Hard Faced Seats and Disc/Wedge – NACE MBS – Monel Trim – NACE MM – Monel Trim – Grafoil Packing and Gasket MMP – Phillips Alkylation MMT – Monel Trim – Teflon Packing and Gasket MT – Chlorine Valve Trim – Monel/Teflon Disc/Hastelloy MTG – Vogt Alkylation MTP – Phillips Alkylation R– Reactive Seal T – Teflon Packing and Gasket ZLB – Zero Leakage Check Valve – Buna N ZLE – Zero Leakage Check Valve – Ethylene Propylene ZLN – Zero Leakage Check Valve – Neoprene ZLV – Zero Leakage Check Valve – Viton 14 . packing and a few design features have also been used as part of the suffix number including T.Female NPT (both ends) B .Female SW by Male Thd TSW .Female SW by Male Couplet CT . B. Expansion of new valve designs are added as new SERIES NUMBERS.Ball Check (female NPT) BS . globe. B and R. F316.Ball Check (SW) SWR .).Female Thd by Female SW TT . Prefix: This maximum 3 alphameric letter beginning the Vogt Valve series number is normally indicative of the valve connection.Ring Joint Flanges S .In-Line Repair (female NPT) RJ . etc.In-line Repairable (SW) SWS . angle. Series Number (typical) SW 12111 F8M Suffix Description: Valve Design/Material: This maximum 5 numeric character uniquely identifies the valve to its design (gate. Historically. etc. R and ER (as listed above) ONLY. (See the VV 200 individual pages for standard series available.Female Thd by Male Butt Weld BW . The prefix and suffix to this number provide details to the design.Female Thd by Male Thd Legend: The prefixes and suffixes based on design are limited to S.Female SW by Male Butt Weld BT .Flow Control Division Vogt Valves Description of Series Number System for Vogt Valves (Order Vogt Valves & Fittings by size—series number) Suffix: This maximum 3 alphameric character ending of the Vogt Valve series number is normally indicative of the valve internal trim package. end connections and trim option including packing. F11. Historically.Female Thd by Male Couplet R .Female Thd by Male SW SW .Female SW by Male SW ST . A valve with the traditional Vogt standard trim package and packing is not assigned a suffix number (see below for suffix descriptions). Order by Size and Series Number. Metal-to-metal seating surfaces accommodate the widest range of pressuretemperature service conditions. body and trim materials and stem packings in addition to a broad range of pressure classes. 5 . and end connections including extended bodies. Dimensions are in inches and millimeters.Flow Control Division Vogt Valves Gate Valve Section – Pages 5-43 Gate valves are designed to operate in a fully open or fully closed position. When open. the media will flow with minimal turbulence and pressure drop through the valve. BOLTED BONNET GATE VALVE SEAL WELDED BONNET GATE VALVE BOLTED BONNET GATE VALVE The rugged construction of FORGED gate valves provide an extended life of safe operation. Dimensions are subject to change without notice. Vogt gate valves are available with a variety of bonnet types. Wedge/Seats: HF 353F8M Trim: 316 Seats: HF A350 LF2 Body/Bonnet 32353 32353MB8 Butt Weld Ends Schedule 40 Dimensions Size Trim: 13% Cr.4 26.34 D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON—maximum temperature 500°F.1 4 100 9.10.38 162 5.6 3.5 1 25 5.00 178 11.1 4.0 10.00 102 6.69 221 1.75 248 99.94 379 2.5 1-1/2 40 6.5 and end-to-end dimensions conform to ASME Standard B16.4 For Cv factors see page 123. Seats: HF 353MB8 Trim: 316 Wedge/Seats: HF 353MM Trim: Monel BW 353* (Sizes 2"-4") (*Same as BW363) (See page 7) Trim: 13% Cr. Flanged Ends 1/16" R.0 C-Closed Trim: 316 Seats: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16. Seats: HF 353FHF Trim: 13% Cr.00 203 14.25 31.8 9.50 12.1 7.12 257 8. 6 3/4 20 4.00 229 18.38 187 . 3 80 8.41 239 1.31 211 7.00 203 57.75 19.00 127 8.7 4.8 14. 112-115 A105 Body/Bonnet A105 Body/Bonnet SERIES NUMBER 353 353T+ (Sizes 1/2-2") Trim: 13% Cr. Blue numerals are in millimeters and kilograms. Seats: HF A-End-to-End Trim: 316 Wedge/Seats: HF B-Open F316/F316L 358 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bold face numerals are in inches and pounds.7 4.8 5. 32353.75 121 12.81 300 2. Valve flanges conform to ASME Standard B16.3 .10 282 9.8 45.50 12.62 117 6.38 162 5.03 458 14. Refer to pages 116-120 for full materials description.50 38.25 108 6.7 3. 358 GATE CLASS 150 (PN 20) For other ratings see pgs.00 50.00 102 7.75 146 23. NPS DN 1/2 15 4.Flow Control Division Vogt Valves Forged Gate Valves ■ ■ ■ ■ ■ ■ ■ ■ Class 150 (PN 20) Conventional Port 285 PSI @ 100°F (19.00 178 31. Valve Matrix A.06 357 11.4 2 50 7.75 69.F.75 146 .8 8.50 165 10.75 146 .1 5.7 BAR @ 38°C) 353. 69 221 1.5 24.38 162 5.7 4.75 146 .06 357 282 357 357 458 11.75 146 29.50 2.81 300 239 300 300 379 2.75 1.1 7.50 12. Refer to pages 116-120 for full materials description.0 .81 11.50 140 6.8 69.0 1-1/2 40 7.F.75 69. Blue numerals are in millimeters and kilograms.75 19.Flow Control Division Vogt Valves Forged Gate Valves ■ ■ ■ ■ ■ ■ ■ ■ Class 300 (PN 50) Conventional Port 740PSI @ 100°F (51.50 9. BW 363 (Sizes 2"-4") Trim: 13% Cr.9 34.9 1/2 15 5. 7 Bold face numerals are in inches and pounds.00 102 8.1 For Cv factors see page 123.00 8.8 50.2 127 30.81 14.0 3.1 4. 112-115 363.06 18.00 305 18.75 146 .94 379 2.50 12.12 282 216 241 282 305 14.10 282 9. Seats: HF Trim: 316 Wedge/Seats: HF C-Closed D-Seat Diameter E-Handwheel Diameter F316/F316L 368 Trim: 316 Seats: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.41 239 1.75 248 77.03 11.10 14.25 31.50 216 11.12 257 8.03 458 14.3 2 50 8. 4 100 12.94 9. 368 GATE CLASS 300 (PN 50) A105 Body/Bonnet SERIES NUMBER Trim: 13% Cr.0 BAR @ 38°C) For other ratings see pgs. 32363.38 162 5.50 11.2 13. Wedge/Seats: HF 363MM Trim: Monel Butt Weld Ends Schedule 40 13363MMP (Size 2" Only) (Full Port) Trim: Monel Listed in Phillips Petroleum Company’s HF Alkylation Process Design Spec.00 9.00 50.0 Butt Weld Ends: 3 2-1/2 2 3 4 80 65 50 80 100 11.34 Weight NPS DN 3/4 20 6.75 7.3 15.00 2.38 187 .8 9.1 35. Size A-End-to-End B-Open A350 LF2 Body/Bonnet 32363 32363MB8 Trim: 13% Cr.00 178 39.2 44.10.00 102 10. Seats: HF BW 363F8M Trim: 316 Seats: HF BW 363MM Trim: Monel Flanged Ends: 1/16" R.00 2.4 7.50 165 8. 1 25 6. Manual.8 5.41 11.7 4.8 38.9 4. 13363MMP.5 20.12 12.00 8.6 57. Valve Matrix A. Seats: HF 363MB8 Trim: 316 Wedge/Seats: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE 363 363FHF Trim: 13% Cr.8 8.00 8.1 50.06 14.6 18.6 Valve flanges conform to ASME Standard B16.00 203 178 203 203 248 67.75 121 15.00 152 6.31 211 7.7 11.50 190 10.5 and end-to-end Dimensions conform to ASME Standard B16.50 38. 50 13. Butt Weld Ends: 1 1-1/2 2 3 4 2 2-1/2 3 4 25 40 50 80 100 50 65 80 100 8.38 162 5.0 51. 112-115 373 373.75 19.50 165 6.8 83.F.50 9.94 187 221 239 300 379 239 300 300 379 .50 11.75 1.5 49.75 146 .6 18.3 88.00 9. Seats: HF BW 373F8M Trim: 316 Seats: HF BW 373MM Trim: Monel Flanged Ends: 1/4" R.9 75.12 11.00 102 12.50 12.81 11.0 7. Seats: HF 373F8M Trim: 316 Seats: HF 373FHF Trim: 13% Cr.3 3.31 10.50 2.8 69.75 7.00 2.1 50.00 2. Dimensions Size A-End-to-End B-Open C-Closed Trim: 316 Seats: HF D-Seat Diameter E-Handwheel Diameter MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.8 38.00 17.4 Bold face numerals are in inches and pounds. 8 3/4 20 7.1 50.81 14.8 69.41 11.75 7.0 For Cv factors see page 123.10 14.03 211 257 282 357 458 282 357 357 458 7.50 12.00 17.38 162 5.06 18.0 40.06 14. .41 11.00 8.34 Weight Class 600 Conventional Port: NPS DN 1/2 15 6.75 5.25 1. Refer to pages 116-120 for full materials description.1 BAR @ 38°C) For other ratings see pgs.8 13. Blue numerals are in millimeters and kilograms.0 5.00 8. Seats: HF 32373MB8 Trim: 316 Wedge/Seats: HF F316/F316L 378 Butt Weld Ends Schedule 80 BW 373 (Sizes 2"-4") Trim: 13% Cr.Flow Control Division Vogt Valves Forged Gate Valves ■ ■ ■ ■ ■ ■ ■ ■ Class 600 (PN 110) Conventional Port 1480 PSI @ 100°F (102. Valve Matrix A.00 2.75 1. 378 GATE CLASS 600 (PN 110) A105 Body/Bonnet SERIES NUMBER Trim: 13% Cr.75 121 146 178 203 248 178 203 203 248 17. Wedge/Seats: HF 373MM Trim: Monel 373MB8 Trim: 316 Wedge/Seats: HF A350 LF2 Body/Bonnet 32373 Trim: 13% Cr.81 14.00 216 241 292 356 432 292 330 356 432 8.94 9.8 50.38 8.00 8.10 14.7 4.7 4.75 146 .5 37.00 11.2 30.4 13.10.00 102 8.6 23.4 40.5 166 30. 32373.50 190 6.50 14.06 18.50 2.00 9.4 22.8 38.5 and end-to-end dimensions conform to ASME Standard B16.00 14.03 11.69 9.8 4.1 31.8 Valve flanges conform to ASME Standard B16. 5 27.75 19. Dimensions Flanged Ends: 1/4" R.50 190 8.1 7.00 25.Flow Control Division Vogt Valves Forged Gate Valves ■ ■ ■ ■ ■ ■ ■ ■ Class 600 (PN 110) Full Port 1480 PSI @ 100°F (102.50 12.9 9. Seats: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.38 187 .00 203 60.31 211 7. Blue numerals are in millimeters and kilograms.75 146 19. 9 1/2 15 6.5 .34 13373MMP (Size 2" Only) Trim: Monel Listed in Phillips Petroleum Company’s HF Alkylation Process Design Spec.8 3/4 20 7.3 3.50 216 9.1 BAR @ 38°C) For other ratings see pgs.5 and end-to-end dimensions conform to ASME Standard B16.00 178 36. Manual.41 239 1.10. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16. Refer to pages 116-120 for full materials description.3 1 25 8.09 357 11.56 243 8.00 102 8.50 165 6.F.9 6.50 292 14.8 2 50 11.8 8.1 4.00 50.9 16.50 38. Valve Matrix B.4 5.10 282 9.7 4.0 For Cv factors see page 123.50 241 11.38 213 1. Bold face numerals are in inches and pounds.81 300 2. 13373MMP GATE CLASS 600 (PN 110) A105 Body/Bonnet SERIES NUMBER Trim: 13% Cr.75 146 .75 121 13. 112-115 13373 13373. 1-1/2 40 9.38 162 5. 50 38. Blue numerals are in millimeters and kilograms.56 319 11.62 321 1.1 BAR @ 38°C) For other ratings see pgs.00 330 21.9 .7 3 80 14. 112-115 11403 11403 GATE CLASS 600 (PN 110) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats ASME B16.75 248 105 47.00 610 20.00 178 45. 1 25 8.5 8.8 9.12 359 12.2 4.00 483 16.7 For Cv factors see page 123.75 527 2.00 483 2.56 14.81 71. Seats: HF Meets API-600 required wall thicknesses Dimensions Size Flanged Ends: 1/4" R.00 203 57.00 25.69 373 1.75 146 31.4 1-1/4 32 9.9 3/4 20 7.8 8.2 Bold face numerals are in inches and pounds.1 5.00 305 169 76.7 12. Valve Matrix C.10.69 246 .75 248 76. Refer to pages 116-120 for full materials description.50 216 12.34 SERIES NUMBER Trim: 13% Cr.75 19.25 31.50 292 19.00 50.00 229 14.1 9.2 14.2 34.50 190 11.4 7.38 416 14.6 2 50 11.38 264 .4 26.50 241 16. 2-1/2 65 13.4 13.Flow Control Division Vogt Valves Forged Gate Valves ■ ■ ■ ■ ■ ■ ■ Class 600 (PN 110) Full Port (Except 2-1/2 & 3) 1480 PSI @ 100°F (102. NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16.5 and end-to-end dimensions conform to ASME Standard B16.75 349 220 99.F.31 287 10.75 121 19.0 20.44 265 9.1 1-1/2 40 9.00 356 24.31 58.50 165 10. 10 1/2 15 6.81 427 2.75 552 19.44 291 1. 1 25 4.5 3/4 20 3.36 238 .1 4.38 111 11.50 38.8 2.75 121 12.8 5.4 2.38 289 10.00 102 5.0 . UOP APPROVED.7 4.75 121 9.4 5.8 2. Refer to pages 116-120 for full materials description.6 3/4 20 4.8 4.50 12.1 7.00 102 10.12 308 10.00 178 23.00 102 10.0 10.1 4. Valve Matrix A.2 BAR @ 38°C) For other ratings see pg. 43211HF2 GATE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 42211MTG+ SW42211MTG+ Trim: Monel Class 800 (PN 130) Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Double Packing Lantern Ring Grease Injector Solid Wedge ASME B16. Dimensions SW43211HF2: 42211MTG: Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON—maximum temperature 500°F.16 258 1.34 HYDROFLUORIC ACID (HF) ALKYLATION VALVES. 121 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld – SW43211HF2 Trim: Monel Bold face numerals are in inches and pounds.16 207 7. 11 1/2 15 3.25 31.16 207 7.Flow Control Division Vogt Valves Forged Gate Valves For HF Alkylation Service ■ ■ ■ ■ ■ ■ ■ ■ ■ Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.8 4.6 8.2 BAR @ 38°C) For other ratings see pgs.72 272 1.38 86 8.75 121 9. Valve Matrix B.38 340 11. 112-115 42211MTG.25 133 13.00 25.16 207 7.50 12.7 4.28 261 9.36 238 .00 102 5.6 8. 1 25 4.00 102 5.6 For Cv factors see page 123. Full Port 1975 PSI @ 100°F (136.56 192 .69 297 1.75 146 17.38 86 8.4 1/2 15 3. Blue numerals are in millimeters and kilograms.56 192 .4 1-1/2 40 4.75 19.38 86 8.50 12.28 261 9.75 19.0 2 50 5.56 192 .75 146 17.4 For Cv factors see page 123.7 4. 7 4.38 162 5. 3/4 20 4.75 121 8.38 86 6. 112-115 43111MMP CLASS 600 (PN 110) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge API 602 ASME B16.1 4. Manual.5 .56 243 8.3 3.8 1 25 4. Valve Matrix B.0 2.75 146 . Blue numerals are in millimeters and kilograms.1 5.Flow Control Division Vogt Valves Forged Gate Valves For HF Alkylation Service ■ ■ ■ ■ ■ ■ ■ Class 600 (PN 110) Full Port 1480 PSI @ 100°F (102.00 25.34 SERIES NUMBER Threaded Socket Weld 43111MMP+ – Trim: Monel Listed in Phillips Petroleum Company’s HF Alkylation Process Design Spec. Refer to pages 116-120 for full materials description.1 BAR @ 38°C) For other ratings see pgs. Dimensions Bold face numerals are in inches and pounds.00 102 8.00 102 5.31 211 7. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight +Valves contain TEFLON — maximum temperature 500°F.75 19.38 213 1.38 111 9.38 187 .50 12.3 For Cv factors see page 123. 12 1/2 15 3.4 5.75 146 12. 1 7. Valve Matrix D.9 For Cv factors see page 123. 13 1/2 15 3.8 4.50 12.25 133 20.06 256 .9 3/4 20 3. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.38 86 10.5 3.7 4.50 38.56 268 10.Flow Control Division Vogt Valves Forged Gate Valves Bellowseal ■ ■ ■ ■ ■ ■ Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.34 SERIES NUMBER Threaded Socket Weld 2801B SW2801B Stem: 316 Bellows: 321SS Wedge/Seats: HF Dimensions Bold face numerals are in inches and pounds.7 4.50 38.75 121 8.25 514 18.1 4.25 133 20.50 12.88 327 12.00 178 28.8 2 50 5.81 478 1.0 1 25 4.00 178 27.06 256 .38 86 10.56 268 10.81 478 1.1 7.00 102 4.00 102 8. 1-1/2 40 5.25 514 18. 112-115 2801B CLASS 800 (PN 130) A105 Body/Bonnet Welded Bonnet Outside Screw & Yoke Bolted Gland Seamless Multi-Ply Bellows Full Hard Faced ASME B16.2 1.8 12.75 19.12 308 .3 12.2 BAR @ 38°C) For other ratings see pgs. Blue numerals are in millimeters and kilograms.00 102 12.6 . 7 4.38 187 .9 2-1/2 65 7.9 2. Seats: HF 12111FHF 12111MB6 ■ ■ ■ ■ ■ ■ ■ ■ HYDROFLUORIC ACID (HF) ALKYLATION VALVES. Refer to pages 116-120 for full materials description.75 121 8.25 133 11.3 3/4 20 3.38 162 5.75 248 75.3 3.8 5.00 178 14. Wedge/Seats: HF 12111F8M SW12111F8M Trim: 316 Seats: HF 12111MB8 SW12111MB8 Trim: 316 Wedge/Seats: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.69 221 1.4 3* 80 8.12 257 8. Valve Matrix A.31 7.5 1-1/2 40 4.00 102 4.00 102 4.00 102 4.75 70 6.75 121 10.12 257 8.75 70 6.03 458 14.75 146 16.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.19 157 5.50 12.2 BAR @ 38°C) For other ratings see pgs.75 121 10.0 2.75 19.00 203 42.19 157 5.75 146 16.50 38.31 7.00 50.75 146 .34 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Dimensions Size A-End-to-End 12111MM 12111MMT+ SW12111MM SW12111MMT+ Trim: Monel B-Open 12111MBS SW12111MBS Trim: Monel Wedge: HF C-Closed D-Seat Diameter E-Handwheel Diameter Weight Bold face numerals are in inches and pounds.2 + Valves contain TEFLON—maximum temperature 500°F.75 146 .8 8.2 1 25 4.1 7.75 146 .8 1-1/4 32 4.69 221 1. 1/2 15 3.09 358 11.34 14 2 50 5.6 7.25 31.41 239 1.8 9.00 178 21.50 12.38 86 6.3 For Cv factors see page 123. UOP APPROVED. THD/SW TSW12111 SW12111FHF Sizes 1/2-2 (No 1-1/4) SW12111MB6 Trim: 13% Cr. 112-115 12111 GATE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 12111 SW12111 12111T+ SW12111T+ SW12111HF6 SW12111HF7 Trim: 13% Cr.0 .1 4.0 7. Blue numerals are in millimeters and kilograms.38 162 5.25 31.8 5.10 282 9.8 2. NPS DN 1/4 8 2.7 4.93 379 2.9 2.75 69. *Outside Scope API602 & B16.8 19.0 34.31 211 7.9 4.38 86 6.81 300 2.2 3/8 10 2.00 102 8.00 102 5.8 9.9 4.00 203 18.75 146 . 50 12.75 70 6. 82401 GATE CLASS 800 (PN 130) SERIES NUMBER Body/Bonnet Threaded F316/F316L 12401 12401T+ F316H Socket Weld SW12401 SW12401T+ Trim: 316 Seats: HF THD/SW TSW12401 12401FHF SW12401FHF Trim: 316 Wedge/Seats: HF 82401 SW82401 Sizes 1/2-2 (No 1-1/4) Trim: 316H Seats: HF 82401FHF SW82401 Sizes 1/2-2 (No 1-1/4) Trim: 316H Wedge/Seats: HF Dimensions Size Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Conventional Port 1920 PSI @ 100°F (132.31 211 7.75 146 .50 12.00 102 5.31 7.8 5.6 7.8 2.7 4.9 4.0 2. Valve Matrix A.00 178 21.38 187 .75 146 .38 86 6.41 239 1.75 146 16.3 3.2 + Valves contain TEFLON—maximum temperature 500°F.25 31.1 4. 15 3/8 10 2. Refer to pages 116-120 for full materials description.9 2.75 19.50 38.8 9.75 121 8.3 For Cv factors see page 123.38 86 6.3 3/4 20 3.10 282 9.38 162 5. NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/4 8 2. 112-115 12401.69 221 1.00 102 8.12 257 8.2 1 25 4.25 133 11.75 121 10.9 .34 Bold face numerals are in inches and pounds.75 146 .7 4.12 257 8.9 4.4 BAR @ 38°C) ■ ■ ■ ■ ■ ■ ■ ■ For other ratings see pgs.38 162 5.8 1-1/4 32 4.9 2.75 121 10.0 7.00 102 4.8 5. 2 50 5.19 157 5.25 31.5 1-1/2 40 4.1 7.75 146 .19 157 5.75 146 16.00 102 4. Blue numerals are in millimeters and kilograms.75 70 6.31 7.00 102 4.2 1/2 15 3.69 221 1. 1 4.75 121 10.8 2.31 7.9 4.8 5.7 4.00 102 4. Wedge/Seats: HF ■ ■ ■ ■ ■ ■ ■ ■ Bold face numerals are in inches and pounds.69 221 1. Blue numerals are in millimeters and kilograms. Cl.0 7.31 7.2 Refer to pages 116-120 for full materials description.19 157 5.75 146 .41 239 1. 12421.00 102 5.00 102 4.38 86 6. 16 3/8 10 2.00 178 21.75 70 6.50 12.5 1-1/2 40 4. Seats: HF 12421FHF SW12421FHF Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr.) Threaded 12321 Socket Weld SW12321 Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr. 3 (2-1/4% Cr.25 133 11.75 146 .9 2. 12521 GATE CLASS 800 (PN 130) SERIES NUMBER Body/Bonnet F11.34 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/4 8 2.9 4.8 9.38 86 6. Valve Matrix A.9 . Cl. 1-1/4 32 4.75 146 16.9 2.38 162 5.25 31.75 121 10.Flow Control Division Vogt Valves Class 800 (PN 130) Forged Gate Valves Conventional Port 2000 PSI @ 100°F (137. Wedge/Seats: HF SW12521 Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr.50 38.75 146 .) F9 (9% Cr.25 31.12 257 8.00 102 8.75 19. 2 (1-1/4% Cr.38 162 5.31 211 7.9 BAR @ 38°C) For other ratings see pgs.50 12. Seats: HF SW12921FHF Trim: 13% Cr.38 187 .69 221 1.75 121 8.7 4.00 102 4.10 282 9.19 157 5. Wedge/Seats: HF 12421 SW12421 Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr. Seats: HF 12321FHF SW12321FHF Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr. Dimensions Size Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.) F5 (5% Cr.6 7.3 3/4 20 3.75 70 6.1 7.3 3.) 12521 12521FHF SW12921 Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr.75 146 .8 5.12 257 8. Seats: HF SW12521FHF Sizes 1/2-2 (No 1-1/4) Trim: 13% Cr. Wedge/Seats: HF 12921 12921FHF F22.3 2 50 5.0 2.75 146 16.8 For Cv factors see page 123. 12921.2 1/2 15 3. 112-115 12321.2 1 25 4. 112-115 F316/F316L Body/Bonnet SERIES NUMBER Threaded Socket Weld 12401C+ SW12401C+ Trim: 316 Seats: HF 12401C GATE CLASS 800 (PN 130) 1920 PSI @ 100°F (132.25 133 28.1 1 25 4. Blue numerals are in millimeters and kilograms.52 674 1.1 For Cv factors see page 123.6 3. 17 1/2 15 3.00 102 6.21 717 26.38 467 17.1 4.4 BAR @ 38°C) 1920 PSI @ -325°F (132. Dimensions NPS DN Size A-End-to-End B-Open ■ ■ ■ ■ ■ ■ ■ ■ Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats Extended Bonnet ASME B16.50 38.1 7.84 656 1.00 102 6.75 121 11.75 19.54 573 21.75 451 .06 687 25. 1-1/2 40 4.9 3.25 31.8 5. Valve Matrix A.8 11.38 86 18.0 3/4 20 3.75 146 19.00 102 22.50 12.62 549 .38 467 17.50 12.7 .00 178 25.9 2 50 5.4 BAR @-198°C) Bold face numerals are in inches and pounds.7 4.6 8.38 86 18.3 5.7 4.Flow Control Division Vogt Valves Forged Gate Valves – Cryogenic Service to -325°F (-198°C) Class 800 (PN 130) Conventional Port For other ratings see pgs.34 C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON—maximum temperature 500°F. Refer to pages 116-120 for full materials description.75 121 27.75 451 . 1 4.7 4.7 4.Flow Control Division Vogt Valves Forged Gate Valves – ASTM A350. Grade LF2 for Temperatures to -50°F (-46°C) Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ ■ Conventional Port 1975 PSI @ 100°F (136.75 121 10.41 239 1.3 2 50 5.38 86 6.9 2.25 133 11.3 3/4 20 3. 112-115 Threaded 32111 SERIES NUMBER Socket Weld SW32111 Trim: 13% Cr. 1/2 15 3.10 282 9. Valve Matrix A. Seats: HF 32111F8M SW32111F8M Trim: 316 Seats: HF 32111MB8 SW32111MB8 Trim: 316 Wedge/Seats: HF 32111MM SW32111MM Trim: Monel THD/SW TSW32111 TSW32111F8M Bold face numerals are in inches and pounds.34 C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.0 7.75 146 16.50 12.8 5. LF2 Body/Bonnet 32111 GATE CLASS 800 (PN 130) For other ratings see pgs. Gr.12 257 8.38 162 5.0 2.8 For Cv factors see page 123.00 178 21.38 162 5. 18 1-1/2 40 4.75 19.2 1 25 4.00 102 8. Blue numerals are in millimeters and kilograms.38 86 6.2 BAR @ 38°C) 1975 PSI @ -50°F (136.8 9.75 146 .50 38.3 3.00 102 4.31 211 7.25 31.38 187 .75 121 8.50 12.9 .75 146 .2 BAR @ -46°C) A350. Dimensions NPS DN Size A-End-to-End B-Open MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.69 221 1.00 102 5.1 7. 4 1-1/4 32 4.38 340 11.8 5. 1-1/2 41000 08 2 41000 09 *Service temperature will be limited by sealant manufacturer's recommendation.75 146 17.72 272 1.16 207 7.75 146 17.38 86 8.1 7.00 102 5.50 12.25 31. Valve Matrix A.75 19.8 4.69 297 1.16 207 7. 1/2. 3/4 41000 04 1 41000 06 1-1/4.50 38.38 86 8.2 BAR @ 38°C)* For other ratings see pgs.00 102 10. 353. 41000 GATE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 12111ER SW12111ER Trim: 13% Cr. Blue numerals are in millimeters and kilograms.25 133 13. 112-115 12111ER. Seats: HF EMISSIONS REDUCTION RETROFIT BONNET ASSEMBLY PACKAGES for Field Retrofitting of Vogt Series Nos.12 308 10.00 102 5.75 121 12.6 1 25 4.34 D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.7 4.Flow Control Division Vogt Valves Forged Gate Valves – Emission Reduction Class 800 (PN 130) (Including Retrofit Bonnet Assembly) Conventional Port ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136. Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Double Packing Lantern Ring Sealant Injector Solid Wedge Hard Faced Seats API 602 ASME B16.75 121 9.4 .7 3/4 20 3.50 12.36 238 .56 192 .6 8.0 For Cv factors see page 123. 12111. 19 1-1/2 40 4.7 4.8 2. 373.12 308 10. SW12111.1 4.00 178 23 10. Dimensions Size NPS DN A-End-to-End B-Open C-Closed Order by this number: Valve Size Retrofit Bonnet (Series above) Assembly Pkg.9 2.75 121 12.8 5.0 2 50 5.28 261 9.72 272 1. 12161 and SW12161 Bold face numerals are in inches and pounds. 363.7 8. 1/2 15 3. No.56 192 .25 31. 00 203 66.8 8.00 50.59 447 2.8 8.00 203 82.7 Valve flanges conform to ASME Standard B16.8 8.00 50. CLASS 600 (PN 110) Class 150 (PN 20) Conventional Port Class 300 (PN 50) Conventional Port 740 PSI @ 100°F (51 BAR @ 38°C) Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats ASME B16. 3" Trim: Hastelloy Stem & Bellows Wedge/Seats: HF Flanged Ends.00 203 72.00 330 19.3 29.84 504 17.5 44.5 37.8 8.59 447 2.84 504 17. Dimensions Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight NPS DN 353R 363R 373R 3 80 8.5 and end-to-end dimensions conform to ASME Standard B16.5 30. Valve Matrix A.00 50.F. Blue numerals are in millimeters and kilograms. 3" Trim: Hastelloy Stem & Bellows Wedge/Seats: HF 353R 363R 373R GATE CLASS 150 (PN 20). Refer to pages 116-120 for full materials description. CLASS 300 (PN 50). Class 600 1/4" R.9 For Cv factors see page 123. 3" Trim: Hastelloy Stem & Bellows Wedge/Seats: HF Class 600 (PN 110) Conventional Port 1480 PSI @ 100°F (102.84 504 17.2 3 80 14.Flow Control Division Vogt Valves Forged Gate Valves – Flexial Design Zero Fugitive Emissions Temperature to 425°F (218°C) A105 Body/Bonnet ■ ■ ■ ■ ■ ■ ■ ■ ■ 285 PSI @ 100°F (19.84 504 17.00 203 64.34 Five Year Limited Warranty Compact Bellows Design e l b a l i a v A r e g n o L o N For other ratings see pgs.84 504 17.00 50.59 447 2.9 3 80 11.84 504 17.8 8. Flanged Ends.F.4 3 80 14. BW 373R 2-1/2 65 13.84 504 17.50 241 19.59 447 2.4 32.8 8.00 203 49. 20 Bold face numerals are in inches and pounds.2 .59 447 2.1 BAR @ 38°C) SERIES NUMBER 373R Size 3" BW 373R Sizes 2-1/2".00 203 59.2 26.3 3 80 11.59 447 2.00 356 19. 112-115 SERIES NUMBER 363R Size 3" BW 363R Sizes 2-1/2".00 356 19. Class 150 & 300 1/16" R.00 203 98.59 447 2.00 203 19.12 282 19.8 8.2 22.7 BAR @ 38°C) Butt Weld Ends Schedule 40 For Class 150 and 300 Schedule 80 For Class 600 SERIES NUMBER 353R Size 3" BW 353R Sizes 2-1/2".12 282 19. BW 353R/363R 2-1/2 65 9.10.00 50.00 50.00 50. 31 211 7.5 For Cv factors see page 123. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.4 . 21 1/2 15 3.00 102 5.1 4.38 213 1.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Full Port 1975 PSI @ 100°F (136.10 282 9. Blue numerals are in millimeters and kilograms.75 121 8.81 300 2.00 50. Wedge/Seats: HF 13111F8M SW13111F8M Trim: 316 Seats: HF 13111MB8 SW13111MB8 Trim: 316 Wedge/Seats: HF 13111MM – – SW13111MM SW13111HF4 SW13111HF5 Trim: Monel 1920 PSI @ 100°F (132.25 133 11. 112-115 13111FHF SW13111FHF Trim: 13% Cr.00 178 14.38 86 6.75 19.50 12. UOP APPROVED.00 102 8.3 3/4 20 4.50 38.56 243 8.41 239 1.8 8. Valve Matrix B.7 4.38 187 .4 2 50 7.09 358 11.00 25.1 7.4 BAR @ 38°C) F316/F316L 13401 SW13401 Trim: 316 Seats: HF ■ ■ ■ ■ ■ ■ ■ ■ Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16. 1-1/2 40 5.8 10. Bold face numerals are in inches and pounds.0 2.75 146 12.75 146 .1 5.8 1 25 4.34 HYDROFLUORIC ACID (HF) ALKYLATION VALVES.4 5.00 203 42.2 BAR @ 38°C) MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE SERIES NUMBER Body/Bonnet Threaded Socket Weld A105 13111 SW13111 Trim: 13% Cr. Seats: HF 13111.38 162 5.8 19. 13401 GATE CLASS 800 (PN 130) For other ratings see pgs.3 3.00 178 22.38 111 9. Valve Matrix A or B.00 50.00 203 57.2 For Cv factors see page 123.84 504 17.59 447 2.00 178 19.34 Five Year Limited Warranty Compact Bellows Design Threaded Socket Weld 12111R SW12111R 13111R SW13111R (Full Port) Trim: Hastelloy Stem & Bellows Wedge/Seats: HF Bold face numerals are in inches and pounds. as applicable.Flow Control Division Vogt Valves Forged Gate Valves – Flexial Design Zero Fugitive Emissions ■ ■ ■ ■ ■ ■ ■ ■ ■ Temperature to 425°F (218°C) A105 Body/Bonnet e l b a l i a v A r e g n o L o N 1975 PSI @ 100°F (136. 112-115 Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats ASME B16.84 504 17. Blue numerals are in millimeters and kilograms.00 203 57. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.8 26. 22 .2 19.2 BAR @ 38°C) Class 800 (PN 130) SERIES NUMBER 12111R.8 8.00 50.00 178 2 50 7.8 26. 12111R 13111R 2-1/2 65 7.59 447 2.8 8. 13111R GATE CLASS 800 (PN 130) For other ratings see pgs. 25 133 12.0 3/8 10 2.7 4.75 273 9.2 3/4 20 3.4 1-1/2 40 4.00 102 4.75 70 6. Blue numerals are in millimeters and kilograms.50 38.9 4. Seats: HF 12161 GATE CLASS 800 (PN 130) A105 Body/Bonnet 12161F8M SW12161F8M Trim: 316 Seats: HF 12161MM SW12161MM Trim: Monel Bold face numerals are in inches and pounds.38 86 6.00 178 23. 1-1/4 32 4.00 102 8.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.50 12.3 2 50 5.88 149 .75 146 16.75 19.25 31. Round Bolted Bonnet Spiral Wound Gasket Inside Screw Stem Screw Gland Solid Wedge Hard Faced Seats API 602 ASME B16.75 121 10.44 164 5.1 1 25 4. 112-115 ■ ■ ■ ■ ■ ■ ■ ■ SERIES NUMBER Threaded Socket Weld 12161 SW12161 Trim: 13% Cr. Valve Matrix A.50 12.00 102 4.7 4.00 102 4.34 23 1/4 8 2.25 31.31 7.75 121 7.4 7.00 102 4.88 149 .1 7.75 70 6.1 7.0 1/2 15 3.8 5.75 146 16.7 2.3 2.8 2.38 238 1.6 10.9 3.25 311 10.7 .75 121 10.6 For Cv factors see page 123.88 149 .75 273 9. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.8 5.88 149 .2 BAR @ 38°C) For other ratings see pgs.38 238 1.31 7.31 211 7.38 187 .44 164 5.44 164 5.44 164 5.1 4.38 70 6.3 2.9 4.56 268 1. 88 149 .5 1.7 4.75 19.34 161 5. 112-115 ■ ■ ■ ■ ■ ■ ■ Threaded 2801 2801 GATE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Socket Weld SW2801 Trim: 13% Cr. 24 1-1/4 32 4.4 1.00 102 3. 1/4 8 2.25 31.34 E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description. NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.9 4.50 165 5.31 236 7.31 7.38 187 .25 31.0 1.75 121 10.38 86 6.25 133 11.38 86 6. Seats: HF THD/SW TSW2801 2801MM SW2801MM Trim: Monel 2801FHF 2801MB6 SW2801FHF TSW2801FHF SW2801MB6 Trim: 13% Cr. Valve Matrix A.5 1 25 4.9 2 50 5.8 5.75 70 6.88 149 .50 12.69 221 1.7 4.88 149 .0 1.50 38.4 3/8 10 2.00 102 3.50 165 5.2 1-1/2 40 4.00 102 3.69 221 1.75 121 10.41 239 1.50 12.00 178 16.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.10 282 9.8 For Cv factors see page 123.75 70 6. Wedge/Seats: HF 2801F8M SW2801F8M Trim: 316 Seats: HF 2801MBS SW2801MBS Trim: Monel Wedge: HF 2801MB8 SW2801MB8 Trim: 316 Wedge/Seats: HF Dimensions Size Bold face numerals are in inches and pounds.2 BAR @ 38°C) For other ratings see pgs.8 5.00 102 3.31 7.75 121 6.9 4. Blue numerals are in millimeters and kilograms.5 5.00 102 8.34 161 5.1 4.1 7.12 257 8.75 146 11.75 146 10.6 3/4 20 3.3 .88 149 .2 2.0 7.9 4.4 1/2 15 3.12 257 8. 22 37.06 26.38 111 2. Seats: HF BT 2901 BT 2901MB6 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Trim: 13% Cr.Flow Control Division Vogt Valves Forged Gate Valves – Extended Body Valves Class 800 (PN 130) Dimensions Conventional Port 2801 2831.50 12.9 1.3 1.25 31.9 1 25 4.7 12.56 39.69 73 7.50 12. Blue numerals are in millimeters and kilograms.94 49.0 1.50 190 .00 203 1.8 5.5 .6 1.38 187 4.0 1.90 22. CT GATE CLASS 800 (PN 130) For other ratings see pgs.) NPS DN 1/2 15 4.8 . F316L BODY/BONNET 1920 PSI @ 100°F (132.75 19.75 146 1. Seats: HF CT 2911* Trim: 13% Cr.12 257 8.7 6.1 8. 2901 2911.8 1.4 2.97 24.31 236 7.6 . Seats: HF CS 2901 Trim: 13% Cr.7 1.6 .88 149 4.50 165 5.6 4.8 .75 19.1 1.8 7.4 1.00 102 1.5 .72 43.47 37.64 16.81 20. N ■ ■ ■ ■ ■ ■ ■ Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.50 38. Seats: HF Trim: 13% Cr Wedge/ Seats: HF } } G TYPE ENDS H Integrally Reinforced Extended Length Male Couplet Female Socket Weld J K M Integrally Reinforced Extended Length Butt Weld End Female Threaded Refer to Pages 116-120 for full materials description.8 10.1 2.56 39.25 31. OS&Y dimensions shown are applicable.50 165 5.9 . For Cv factors see Page 123 Value Matrix E.00 178 .00 102 .6 4.9 .34 25 P R Weight (Approx. 112-115 Size A105 BODY/BONNET 1975 PSI @ 100°F (136.6 1.0 1.25 57.97 24.00 178 .3 3.8 Bold face numerals are in inches and pounds.2 BAR @ 38°C) SERIES NUMBER CT 2901 Trim: 13% Cr.9 2.69 42.9 1.3 1-1/2 40 5.56 65.69 17.4 BAR @ 38°C) SERIES NUMBER CT 2831 Trim: 316 Seats: HF } TYPE ENDS C Integral Male Couplet Female Threaded D E F A105 BODY/BONNET 1975 PSI @ 100°F (136.7 6. except for the open/closed dimensions which exceed those shown.56 39.3 .00 102 .47 11. *Inside Screw Stem valves are not illustrated above. however.65 16.00 25.25 31.6 1.88 149 4.00 127 2.2 1.00 102 1.81 20.00 51 7.47 11.69 221 5.75 121 .38 60 8.69 73 7. .25 31.0 3/4 20 4. BT.75 19.2 BAR @ 38°C) A SERIES NUMBER CT 2801 Trim: 13% Cr. Seats: HF B F316. 8 10.32 33.) } } Integral Male Socket Weld Female Threaded (See above illus. ST.00 51 .69 73 .00 102 1. *Inside Screw Stem valves are not illustrated above.47 11. OS&Y dimensions shown are applicable.31 236 7.8 4.6 7. 112-115 2801 2811.65 16.1 1. Blue numerals are in millimeters and kilograms. 2831.34 J L M Weight (Approx.) NPS DN MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE 26 Refer to Pages 116-120 for full materials description.4 BAR @ 38°C) ST 2831 Trim: 316 Seats: HF D F G H TYPE ENDS } B Integral Male Threaded Female Threaded A105 BODY/BONNET 1975 PSI @ 100°F (136. except for the open/closed dimensions which exceed those shown. For Cv factors see Page 123 Value Matrix E.Flow Control Division Vogt Valves Forged Gate Valves – Extended Body Valves Class 800 (PN 130) Conventional Port Dimensions For other ratings see pgs.) 1/2 15 4.69 17.84 21.2 BAR @ 38°C) ST 2801 A MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE ■ ■ ■ ■ ■ ■ ■ Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.3 1.2 12. TT 2811 and TT 2831 male threaded valves are not covered under API 602 rules. TT.64 16.4 2.3 1-1/2 40 5.9 1 25 4.25 31.05 26.47 37.25 57.8 4.8 Bold face numerals are in inches and pounds. Seat: HF F316/F316L BODY/BONNET 1920 PSI @ 100°F (132.00 102 1.50 165 5.3 3.38 60 1.2 BAR @ 38°C) SERIES NUMBER TT 2801 Trim: 13% Cr. Seats: HF Trim: 316 Seats: HF Trim: Monel Trim: 13% Cr. Wedge/Seats: HF F316/F316L BODY/BONNET 1920 PSI @ 100°F (132.69 221 5.7 1.88 149 4.5 1.12 257 8.88 149 4.38 111 2.75 121 .9 1.00 102 .75 146 1.4 BAR @ 38°C) TT 2831 Trim: 316 Seat: HF Size TYPE ENDS } SERIES NUMBER ST 2801F8M ST 2801MM ST 2801FHF ST 2801MB8 ST 2801MB6 SS 2801 SS 2801MB6 Trim: 13% Cr.9 6.25 31.25 31. Wedge/Seats: HF Trim: 316 Wedge/Seats: HF Trim: 13% Cr. Integral Male Socket Weld Female Threaded Integral Male Socket Weld Female Socket Weld (Not illus.56 39.90 22.9 6.90 48.69 73 .3 2. however. SS GATE CLASS 800 (PN 130) A105 BODY/BONNET 1975 PSI @ 100°F (136.47 11. .5 1. Wedge/Seats: HF TT 2811* Trim: 13% Cr.00 102 .8 5. Seats: HF Trim: 13% Cr.50 165 5. Wedge/Seats: HF Trim: 13% Cr.3 .3 1.0 3/4 20 4. Seat: HF TT 2801MM Trim: Monel TT 2801F8M Trim: 316 Seats: HF TT 2801MB8 Trim: 316 Wedge/Seats: HF TT 2801MB6 Trim: 13% Cr.5 8.00 127 2.38 187 4. 1/2" TT 2801. 1 1.5 Bold face numerals are in inches and pounds.72 69 8.50 12.75 19.22 37.6 . The valve can be welded directly to a pipe header or vessel.56 39. Seats: HF BT 12111MB8 Trim: 316 Wedge/Seats: HF TYPE ENDS Integrally Reinforced Extended Length Male Butt Weld Couplet Female Threaded BS 12111 Integrally Reinforced Extended Length Male Butt Weld Couplet Female Socket Weld (not illustrated) Trim: 13% Cr.00 25.7 1.31 236 7.00 178 .97 24.50 38.00 203 1.4 4.00 102 .09 53 7.6 5.) NPS DN 1/2 15 1.38 162 5.56 39.0 1.72 43.2 BAR @ 38°C) CT 12111.56 65.75 19. Valve designs similar to the above are available without the 0.7 6.50 12. BS 12111 GATE CLASS 800 (PN 130) Dimensions Size B SERIES NUMBER CT 12111 Trim: 13% Cr. Note: The valves illustrated on this page do not require an interfacing fitting.25 31.00 178 .6 6.94 49.75 146 4. For Cv factors see Page 123 Value Matrix F.12 257 8.38" integral backing ring. Seats: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE } } Weight (Approx.1 2. 27 .6 .97 50 7.38 187 4.4 1.75 146 1.5 1 25 2.75 121 1. Seats: HF CT 12111MB8 Trim: 316 Wedge/Seats: HF } C TYPE ENDS Integrally Reinforced Extended Length Male Couplet Female Threaded MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE E F ■ ■ ■ ■ ■ ■ ■ Bolted Bonnet Outside Screw &Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.7 3/4 20 1.69 221 5. 112-115 A105 Body/Bonnet 1975 PSI @ 100°F (136. Blue numerals are in millimeters and kilograms.8 10.50 190 .00 102 .Flow Control Division Vogt Valves Forged Gate Valves – Extended Body Valves Class 800 (PN 130) Conventional Port For other ratings see pgs.1 8.7 6.1 1.5 7.6 2.75 146 4.97 24.38 162 5. Refer to Pages 116-120 for full materials description. BT 12111.8 9.97 50 7.0 2.7 16.75 19.34 G H K P R SERIES NUMBER BT 12111 Trim: 13% Cr. Can be disassembled for post weld heat treat procedure after installation if gate orientation is marked and maintained in same valve when reassembled.3 1-1/2 40 2. 1 1.3 3.5 7.72 69 1.3 1-1/2 40 8.Flow Control Division Vogt Valves Forged Gate Valves – Extended Body Valves Class 800 (PN 130) Conventional Port For other ratings see pgs.00 178 1.1 1.56 39.75 19. For Cv factors see Page 123 Valve Matrix F.4 1.47 11.2 BAR @ 38°C) ■ ■ ■ ■ ■ ■ ■ A Bolted Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.50 191 2.9 6.8 10.7 7.0 16.75 121 1. Integral Male Socket Weld Female Threaded Refer to Pages 116-120 for full materials description.94 49. Can be disassembled for post weld heat treat procedure after installation if gate orientation is marked and maintained in same valve when reassembled.75 146 4.38 162 5.) Type Ends } NPS DN 1/2 15 6.09 53 .7 1.25 31.6 3/4 20 7.00 203 2. Wedge/Seats: HF (Approx. 28 .31 211 7.38 162 5.84 21 1.75 146 4.56 65.5 Bold face numerals are in inches and pounds.7 2.97 50 .12 257 8.38 187 4.50 38.1 8. Seats: HF ST 12111MB8 Trim: 316 Wedge/Seats: HF ST 12111MB6 Trim: 13% Cr.6 4. Blue numerals are in millimeters and kilograms.05 26.32 34 1.56 39.9 1 25 7.6 5.75 146 1.1 1.69 221 5.9 6.00 102 .90 48 2.64 16.34 B D F G H J L MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE M Weight SERIES NUMBER ST 12111 Trim: 13% Cr.97 50 .75 19.3 .50 165 1.47 11.00 25.00 102 . 112-115 Dimensions Size ST12111 GATE CLASS 800 (PN 130) A105 Body/Bonnet 1975 PSI @ 100°F (136. 00 152 2.4 6.41 10.3 3. Can be disassembled for post weld heat treat procedure after installation if gate orientation is marked and maintained in same valve when reassembled.56 65.7 7.9 1 25 5.6 4.5 Bold face numerals are in inches and pounds.94 49.75 146 1. Refer to Pages 116-120 for full materials description.47 11.50 114 1.3 2.34 H J M Weight NPS DN 1/2 15 4. 112-115 Dimensions Size A TT12111 GATE CLASS 800 (PN 130) A105 Body/Bonnet 1975 PSI @ 100°F (136.97 50 . Wedge/Seats: HF TT 12111MB8 Trim: 316 Wedge/Seats: HF TT 12111MB6 Trim: 13% Cr.6 3/4 20 4.Flow Control Division Vogt Valves Forged Gate Valves – Extended Body Valves Class 800 (PN 130) Conventional Port For other ratings see pgs.52 13.8 10.75 146 4.31 211 7.25 31.0 16.25 133 2.69 221 5.56 39.7 2.38 187 4.3 1-1/2 40 6.47 37. Wedge/Seats: HF D Type Ends } F Male Threaded Female Threaded MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE G ■ ■ ■ ■ ■ ■ ■ Bolted Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.9 6.89 22.5 7.72 69 1.56 39. For Cv factors see Page 123 Valve Matrix F. 29 .97 50 . Seats: HF TT 12111FHF Trim: 13% Cr.64 16.3 1.38 162 5. Blue numerals are in millimeters and kilograms.75 146 4.50 114 1.69 17.38 162 5.6 1.12 257 8.75 121 .2 1.6 5.00 102 .2 BAR @ 38°C) B SERIES NUMBER TT 12111 Trim: 13% Cr.09 53 .5 8.00 102 .1 1. 9 2 50 5.6 3/4 20 3.00 102 3.31 236 7.50 165 5. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON—maximum temperature 500°F.50 12.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ Conventional Port 1920 PSI @ 100°F (132.12 257 8.1 7.1 4. Blue numerals are in millimeters and kilograms.00 102 3.25 133 11.50 12.88 149 .5 1 25 4.75 19.7 4.00 178 16.5 1.41 239 1.4 1.75 121 10.10 282 9.0 7.75 121 6.38 187 .8 5. Refer to pages 116-120 for full materials description.50 165 5.4 BAR @ 38°C) F316/F316L Body/Bonnet 2831 GATE CLASS 800 (PN 130) For other ratings see pgs.3 . 112-115 SERIES Threaded 2831 2831T+ Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.88 149 . 1/2 15 3.34 NUMBER Socket Weld SW 2831 SW 2831T+ Trim: 316 Seats: HF Dimensions Bold face numerals are in inches and pounds.8 For Cv factors see page 123.25 31. 30 1-1/2 40 4.38 86 6.69 221 1.00 102 8.7 4.9 4.75 146 10.2 2.38 86 6. Valve Matrix A.50 38. 6 5. Valve Matrix A.62 168 6. 112-115 SERIES NUMBER Threaded Socket Weld 2811 SW 2811 Trim: 13% Cr.75 121 6.38 213 7.2 BAR @ 38°C) For other ratings see pgs.34 SW2811FHF Trim: 13% Cr.50 12.1 2. Blue numerals are in millimeters and kilograms.0 2 50 5.1 1.8 5.56 268 1.50 38.75 146 11.2 1. 31 1-1/2 40 4.7 4.62 168 6.38 86 6.75 191 4.5 3/4 20 3.0 5.75 121 10.00 102 8.00 178 18.7 4.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Conventional Port ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136.00 102 3.81 275 9.1 7.4 1 25 4.3 For Cv factors see page 123. 1/2 15 3.75 146 11. Wedge/Seats: HF Bold face numerals are in inches and pounds.4 .75 121 10. Seats: HF 2811 GATE CLASS 800 (PN 130) A105 Body/Bonnet 2811FHF THD/SW TSW2811 Welded Bonnet Inside Screw Stem Screw Gland Solid Wedge Hard Faced Seats API 602 ASME B16.38 70 6.25 31.12 308 10.00 152 .00 102 3.38 238 1.38 238 1.25 133 12.00 152 .8 5.5 8.8 1-1/4 32 4.25 31.81 275 9. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.44 189 .50 12. 38 70 6. NPS DN C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON—maximum temperature 500°F.44 164 5.44 164 5.88 149 .31 7.7 1 25 4.50 12.00 178 22.1 .00 102 3.75 70 6.7 1.31 7.34 Bold face numerals are in inches and pounds.00 102 3.44 164 5.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Conventional Port ■ ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136.50 38.88 149 .25 235 1.75 121 6.25 235 1.1 7.44 164 5.69 272 9.8 5.7 1.44 189 .25 31. Refer to pages 116-120 for full materials description.25 311 10. 32 1-1/4 32 4.88 149 . Seats: HF 59851.4 1-1/2 40 4. Valve Matrix A.9 4.75 121 10.7 3/8 10 2.50 12.2 6.1 For Cv factors see page 123.75 121 10.75 146 14.75 146 13.7 1/2 15 3.6 6.75 19.25 31.56 239 1.2 2 50 5.3 10.38 86 6.25 133 12.9 3. 59951 GATE CLASS 800 (PN 130) For other ratings see pgs.9 4.00 102 8.00 102 3.75 70 6.1 4.88 149 . 1/4 8 2.9 1. 112-115 59851F8M SW59851F8M Trim: 316 Seats: HF 59851MM SW59851MM Trim: Monel 59851MBS SW59851MBS Trim: Monel Wedge: HF Socket Weld SW59851 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Dimensions Size 1920 PSI @ 100°F (132.8 3/4 20 3.69 272 9.38 213 7.4 BAR @ 38°C) A-End-to-End F316/ F316L B-Open 59951 (Sizes 1/4-1 Only) 59951T+ (Sizes 1/4-1 Only) Trim: 316 Seats: HF Union Bonnet Spiral Wound Gasket Inside Screw Stem Screw Gland Solid Wedge Hard Faced Seats API 602 ASME B16.00 102 3.7 4.7 1.7 4.8 5. Blue numerals are in millimeters and kilograms.2 BAR @ 38°C) SERIES NUMBER Body/Bonnet Threaded A105 59851 Trim: 13% Cr. 1 5.75 197 24. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.4 7.50 38.00 229 19.38 416 14.75 527 2. Bold face numerals are in inches and pounds.25 31.31 58.2 BAR @ 38°C) ■ ■ ■ ■ ■ ■ ■ For other ratings see pgs.8 9.2 18.34 Meets API-600 required wall thicknesses.00 203 41. 112-115 SERIES NUMBER Threaded Socket Weld 11103 SW11103 Trim:13% Cr.56 14.25 260 21.8 .75 248 58.00 178 29.62 321 1.7 1-1/2 40 7.4 2 50 9.75 349 134 60.8 3 80 7.56 268 9. 2-1/2 65 10.62 244 .00 305 134 60.00 610 20.81 71.00 50.1 9.75 19.75 298 10.6 5.2 For Cv factors see page 123. Blue numerals are in millimeters and kilograms.1 26.00 483 16.8 41.75 248 90.00 483 2.8 8.78 223 .4 13.Flow Control Division Vogt Valves Forged Gate Valves Class 800 (PN 130) Full Port (Except 2-1/2 & 3) 1975 PSI @ 100°F (136.50 114 10. Valve Matrix C.4 13.81 427 2.7 12.2 4. Seats: HF 11103 GATE CLASS 800 (PN 130) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats ASME B16.12 359 12.25 184 16.75 121 12.9 1 25 5.75 552 19.62 92 9.5 8.7 3/4 20 4.3 1-1/4 32 6.00 127 11.00 25.56 243 8.56 268 1.69 373 1. 33 1/2 15 3.75 146 19.50 165 14. 1-1/2 40 12.6 15. Blue numerals are in millimeters and kilograms.75 121 20.97 253 1.1 7.1 9.1 42.75 248 94.F.69 246 8.1 1 25 10.2 7.25 31.50 38.8 3/4 20 9. Valve Matrix A.38 289 9.8 8.50 216 7.Flow Control Division Vogt Valves Forged Gate Valves Class 1500 (PN 260) API 602/ASME B16.50 368 13.1 9.34 Conventional Port ■ ■ ■ ■ ■ ■ ■ ■ 3705 PSI @ 100°F (255.7 4. Wedge/Seats: HF 15373 15373 GATE CLASS 1500 (PN 260) A105 Body/Bonnet Dimensions Flanged Ends 1/4" R.00 203 48.7 4.50 12.50 12.16 309 1.88 175 .84 351 12.0 2 50 14. Seats: HF 15373FHF Trim: 13% Cr. Class 1500 (Conventional Port): Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16.75 19.00 254 9.75 121 17.7 For Cv factors see page 123.78 268 . Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats Integral Hard Faced Seat ASME B16.00 178 34. Seats: HF RJ15373FHF Trim: 13% Cr. 112-115 SERIES NUMBER Trim: 13% Cr.00 305 11.5 and end-to-end dimensions conform to ASME Standard B16.00 229 7. Refer to pages 116-120 for full materials description.10. Wedge/Seats: HF RING JOINT FACES RJ15373 Trim: 13% Cr.88 175 . 34 1/2 15 8.5 22.34 Bold face numerals are in inches and pounds.47 243 6.5 BAR @ 38°C) For other ratings see pgs.7 .47 243 6. 50 216 12. Refer to pages 116-120 for full materials description.38 467 1. 11683 A105 Body/Bonnet SERIES NUMBER 11603 1/4" Raised Faces 11683 Ring Joint Faces Trim: 13% Cr.4 .00 356 12.00 305 20.25 540 2.00 178 43.00 279 17.5 2 50 14. Blue numerals are in millimeters and kilograms.5 and end-to-end dimensions conform to ASME Standard B16.62 397 14. 112-115 GATE CLASS 1500 (PN 260) 11603.4 8.8 13. Class 1500 (Full Port): NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16.12 308 11. Valve Matrix G.00 178 55.34 Full Port 3705 PSI @ 100°F (255.00 203 76.56 598 21.38 35.7 3/4 20 9.00 229 14.8 For Cv factors see page 123.44 418 1. Dimensions Bold face numerals are in inches and pounds.F.50 368 .0 34.50 368 23.0 25.0 1 25 10.38 289 .5 1-1/4 32 11.56 14.4 9. 35 1/2 15 8.00 305 117.1 7.75 19.0 12.8 53.12 511 18.12 28.2 7.34 Meets API-600 required wall thicknesses.75 451 16.00 50. Seats: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats Integral Hard Faced Seat ASME B16. 1-1/2 40 12.0 41.75 349 230 104.5 BAR @ 38°C) For other ratings see pgs.75 248 92.3 19. Flanged Ends 1/4" R.00 254 15.88 22.Flow Control Division Vogt Valves Forged Gate Valves ■ ■ ■ ■ ■ ■ ■ ■ Class 1500 (PN 260) ASME B16.94 329 .10. 00 178 29. Seats: HF Meets API-600 required wall thicknesses.9 3/4 20 5.50 165 14.2 5.12 435 1.50 241 21.88 378 1.2 1-1/4 32 7. Dimensions Size Bold face numerals are in inches and pounds.6 For Cv factors see page 123.00 305 116.75 273 .3 8. 36 1-1/2 40 9.0 28. Blue numerals are in millimeters and kilograms.00 533 18.38 35.38 416 14. 1/2 15 4.75 273 10.75 248 100 45.00 50.4 2 50 9.00 254 .75 191 7.4 20.9 9.8 12.5 BAR @ 38°C) ■ Round Bolted Bonnet ■ Flat Gasket Joint or Ring Joint Gasket ■ Outside Screw & Yoke ■ Bolted Gland ■ Solid Wedge ■ Hard Faced Seats ■ ASME B16. Valve Matrix G.50 114 10.9 13.69 475 2.88 22.69 297 10.00 127 11.75 146 21. 1043 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 1033 SW1033 1043 SW1043 Ring Joint Gasket Bonnet (Not illustrated) Trim: 13% Cr.25 184 16.94 329 .1 9.Flow Control Division Vogt Valves Forged Gate Valves Class 1500 (PN 260) Full Port 3705 PSI @ 100°F (255.00 229 18.00 203 44. 112-115 GATE CLASS 1500 (PN 260) 1033.8 .3 52.6 1 25 6. NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.56 14.8 9.06 357 12.25 31.75 248 63.34 For other ratings see pgs.75 476 17. 5 BAR @ 38°C) For other ratings see pgs.84 351 12.8 8.2 21.38 289 9.2 1-1/4 32 5.2 For Cv factors see page 123. 15321.97 253 1. Seats: HF 15111F8M SW15111F8M Trim: 316 Seats: HF 15111FHF SW15111FHF Trim: 13% Cr.75 121 9.25 133 11.50 12.1 7.3 BAR @ 38°C) 15401 SW15401 Sizes 1/2-2 (No 1-1/4) Trim: 316 Seats: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bold face numerals are in inches and pounds.6 BAR @ 38°C) 15321 SW15321 Trim: 13% Cr.25 31.78 223 .0 8. Valve Matrix A.4 3.25 133 11.47 190 6.Flow Control Division Vogt Valves Forged Gate Valves Class 1500 (PN 260) Conventional Port ■ ■ ■ ■ ■ ■ ■ ■ 15111.50 38.7 4.00 203 26.97 253 1.8 1 25 4.25 31.75 121 8. 15401 GATE CLASS 1500 (PN 260) 3705 PSI @ 100°F (255. Wedge/Seats: HF 15111MB6 SW15111MB6 Trim: 13% Cr. Blue numerals are in millimeters and kilograms.8 8.9 12.50 12. Seats: HF 3600 PSI @ 100°F (248.75 19.9 Refer to pages 116-120 for full materials description.75 248 48. 112-115 SERIES NUMBER Body/Bonnet Threaded Socket Weld A105 15111 SW15111 Trim: 13% Cr.1 9.7 4. Dimensions Size Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16. 2 50 7.47 190 6. 37 3/4 20 4.38 289 9.75 121 8.69 246 8.00 178 13.00 178 18.88 175 .3 1-1/2 40 5.9 .0 12.5 3. Wedge/Seats: HF 15111MBS SW15111MBS Trim: Monel Wedge: HF SW15111MB8 Trim: 316 Wedge/Seats: HF 15111MB8 F11 CL2 F316/ F316L 3750 PSI @ 100°F (258.00 102 7.88 175 .00 203 27.16 309 1.34 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/2 15 4.00 102 7. 1/2 15 4.00 178 18. Valve Matrix A.5 BAR @ 38°C) 3705 PSI @ -50°F (255.75 248 48. Gr.00 102 7.97 253 1.38 289 9.2 For Cv factors see page 123.75 121 8.Flow Control Division Vogt Valves Forged Gate Valves – ASTM A350.16 309 1.1 7.34 A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.7 4.2 21.7 4.9 12.88 175 .47 190 6.8 8. 38 1-1/2 40 5.2 2 50 7.9 3/4 20 4.47 190 6.00 102 7. Seats: HF 35111F8M SW35111F8M Trim: 316 Seats: HF 35111MB8 SW35111MB8 Trim: 316 Wedge/Seats: HF Bold face numerals are in inches and pounds.5 BAR @ -46°C) A350.0 8.50 12.8 1 25 4.1 9. 112-115 SERIES NUMBER Threaded Socket Weld 35111 SW35111 Trim: 13% Cr.25 31.9 .25 133 11.69 246 8.50 38.75 121 9. LF2 Body/Bonnet 35111 GATE CLASS 1500 (PN 260) For other ratings see pgs.75 19.75 121 8.84 351 12.5 3.78 223 . Grade LF2 for Temperatures to –50°F (–46°C) Class 1500 (PN 260) ■ ■ ■ ■ ■ ■ ■ ■ Conventional Port 3705 PSI @ 100°F (255. Blue numerals are in millimeters and kilograms.50 12.00 203 26. Dimensions NPS DN Size MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.00 178 13.4 3.88 175 . Valve Matrix B. 112-115 16111 GATE CLASS 1500 (PN 260) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 16111 SW16111 Trim: 13% Cr.50 38.00 203 28.50 12.75 19.1 7.97 253 1.5 12.5 BAR @ 38°C) For other ratings see pgs.00 25. 1/2 15 4.84 351 12.25 133 11.47 190 6.16 309 1.75 121 9.1 9.34 Bold face numerals are in inches and pounds.38 289 9.7 4.3 1-1/2 40 7.4 8.88 175 .9 1 25 5.00 178 13. Seats: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.97 253 1.9 For Cv factors see page 123. Blue numerals are in millimeters and kilograms. 39 1-1/4 32 5. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.9 3/4 20 4.69 246 8.0 12.00 178 17.Flow Control Division Vogt Valves Forged Gate Valves Class 1500 (PN 260) Full Port ■ ■ ■ ■ ■ ■ ■ ■ 3705 PSI @ 100°F (255.9 .00 203 27.75 121 8.00 102 7.12 282 9.78 223 .2 21.25 133 11.8 8.25 31.5 3.75 248 48.5 7. 41 290 9.69 246 8.34 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bold face numerals are in inches and pounds.25 31.16 309 1.7 4.5 7. Wedge/Seats: HF 15801MM SW15801MM Trim: Monel 15801MB8 15801MBS SW15801MB8 Trim: 316 Wedge/Seats: HF SW15801MBS Trim: Monel Wedge: HF F316/F316L 3600 PSI @ 100°F (248.3 1 25 4. 1-1/2 40 5.75 121 9.1 9.84 352 12.97 253 1.97 253 1.5 BAR @ 38°C) For other ratings see pgs.53 191 6.3 For Cv factors see page 123.4 3/4 20 4.00 102 7. Blue numerals are in millimeters and kilograms.3 BAR @ 38°C) 15831 SW15831 Trim: 316 Seats: HF Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.2 3.2 8.Flow Control Division Vogt Valves Forged Gate Valves Class 1500 (PN 260) ■ ■ ■ ■ ■ ■ ■ Conventional Port 3705 PSI @ 100°F (255.00 102 7.25 133 11. Seats: HF 15801FHF SW15801FHF Trim: 13% Cr.00 203 18.53 191 6.7 4.8 8.88 175 .9 2 50 7.75 121 7.8 8.88 175 . 112-115 15801.75 248 37.78 223 .1 7.75 121 7.50 12.50 12.8 .00 203 17. 15831 GATE CLASS 1500 (PN 260) A105 Body/Bonnet Threaded 15801 SERIES NUMBER Socket Weld SW15801 Trim: 13% Cr.25 133 11.25 31.75 19.1 1-1/4 32 5.5 6. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.41 290 9.00 178 13.50 38.00 178 13.4 3.0 16. 40 1/2 15 4. Valve Matrix A. 88 175 4.12 28.7 1.69 119 2.9 1 25 5.5 1.1 9.53 191 6.00 51 .53 191 6.0 6.75 121 . 41 .00 51 . Seats: HF ST 15801F8M Trim: 316 Seats: HF } A TYPE ENDS Integral Male Socket Weld Female Threaded B D F G H ■ ■ ■ ■ ■ ■ ■ Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Wedge Hard Faced Seats API 602 ASME B16.5 BAR @ 38°C) ST 15801 GATE CLASS 1500 (PN 260) A105 BODY/BONNET SERIES NUMBER ST 15801 Trim: 13% Cr. For Cv factors see Page 123 Valve Matrix A.5 2.84 21.7 7.75 19.4 1.75 121 .05 26.5 .69 17.7 7.2 14.7 4.3 1. 112-115 Size 3705 PSI @ 100°F (255.56 39.38 137 2.88 175 4.50 12.69 246 8.50 12.69 17.6 8.78 223 7.34 J L M Weight NPS DN 1/2 15 4.69 119 2.38 60 .6 8.25 57.32 33.00 178 1.0 3/4 20 4.56 39.Flow Control Division Vogt Valves Forged Gate Valves – Extended Body Valves Class 1500 (PN 260) Dimensions Conventional Port For other ratings see pgs.5 3.4 Refer to Pages 116-120 for full materials description. 19 208 . Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.5 1 25 5.06 357 1.1 12.Flow Control Division Vogt Valves Forged Gate Valves Class 2500 (PN 420) Full Port 6250 PSI @ 100°F (431. 112-115 ■ ■ ■ ■ ■ ■ Socket Weld SW66703 Trim: 13% Cr.00 305 65.50 216 15.12 130 11. Welded Bonnet Outside Screw & Yoke Bolted Gland Solid Hard Faced Wedge Hard Faced Seats ASME B16. Blue numerals are in millimeters and kilograms.81 224 8.7 . 66773 GATE CLASS 2500 (PN 420) For other ratings see pgs. 3 (2-1/4% Cr.8 2 50 8.) 66713 SW66713 Trim: 13% Cr.0 BAR @ 38°C) SERIES NUMBER Body/Bonnet Threaded A105 66703 66703.0 9.00 279 10. Wedge/Seats: HF Bold face numerals are in inches and pounds.00 279 10.88 403 14. 66713.12 130 11. Wedge/Seats: HF F22.1 8.75 19.1 8.00 305 65.50 38.75 19.5 29.7 29.88 403 14. 2 (1-1/4% Cr.00 102 8.06 357 1.00 203 21. Cl.1 9.1 12.) 66773 SW66773 Trim: 13% Cr. Valve Matrix H.00 203 20. 1-1/2 40 8.00 254 .4 5.7 3. Pressure Class 42 1/2 15 4.50 38. Wedge/Seats: HF F11.00 254 .75 146 8.34 LTD.1 For Cv factors see page 123.50 216 15.41 10.9 3/4 20 5. Cl. 9 219. LF2 (1) (2) PSI CLASS 1500 ASTM A350. LF2 (1) (2) PSI Service Temperature (°C) PN 130 (CLASS 800) ASTM A350.8 700 1420 2665 300 103. MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE *NOTE: Other Vogt valves are also offered in A350-LF2 construction. Valve Matrix A.6 226. . CLASS 1500 (PN 260) PRESSURE-TEMPERATURE RATINGS PRESSURE-TEMPERATURE RATINGS Service Temperature (°F) CLASS 800 ASTM A350. GR. Seats: HF SERIES NUMBER Threaded Socket Weld Size 1/2”-2” 35111 SW35111 Trim: 13% Cr.5 BAR @ 38°C) A350. LF2 (1) (2) BAR –50 to 100 1975 3705 –46 to 38 136.2 600 1460 2735 250 111. Seats: HF 32111F8M 35111F8M SW32111F8M Trim: 316 Seats: HF 32111MB8 SW32111MB8 Trim: 316 Wedge/Seats: HF See Dimensions on Pg. LF2 Body/Bonnet A350.2 208. GR.5 200 1800 3375 50 133. 35111 GATE CLASS 800 (PN 130).0 400 1690 3170 150 120.2 255.5 300 1750 3280 100 123.1 172. GR. GR. GR.0 500 1595 2995 200 116.0 (1) Ratings are in accordance with ASME/ANSI B16.2 BAR @ 38°C) 3705 PSI @ 100°F (255. Grade LF2 ■ Charpy Impact Tested ■ Verified Strength and Toughness ■ Flexible Graphite Packing ■ Flexible Graphite Filled Gasket ■ API 602 ■ ASME B16. 38 43 For Cv factors see page 123. (2) Permissible but not recommended for prolonged use above 800°F (427°C). GR.34-96. LF2 Body/Bonnet SERIES NUMBER Threaded Socket Weld Size 1/2”-2” 32111 SW32111 Trim: 13% Cr.7 232.34 1975 PSI @ 100°F (136.9 144.6 800 1100 2060 400 92. LF2 (1) (2) BAR PN 260 (CLASS 1500) ASTM A350. Class 800 (PN 130)* Class 1500 (PN 260)* Conventional Port Conventional Port ■ Traceable Parts From Stock ■ Machined Parts Heat Treated to ASTM A350. GRADE LF2 Class 800 and Class 1500 Valves FOR APPLICATIONS WHERE TEMPERATURES TO –50°F (–46°C) ARE THE RULE NOT THE EXCEPTION! 32111.3 193.Flow Control Division Vogt Valves Forged Gate Valves – ASTM A350.5 250. See individual pages of VV200 Catalog. 18 Refer to pages 116-120 for full materials description.5 425 76. SW35111F8M Trim: 316 Seats: HF 35111MB8 SW35111MB8 Trim: 316 Wedge/Seats: HF See Dimensions on Pg. 28 33 9.75 121 1.56 65 . NUCLEAR GATE.50 12.50 12.7 5. Other Vogt valve designs can B MIN.69 68 10.00 25 6.10 282 .7 9.25 159 2.06 78 .38 9.50 114 1.00 25 6. D A popular Vogt nuclear valves.00 102 .50 12. Blue numerals are in millimeters.7 4.75 197 2.38 9. 416SS.62 168 .84 352 .50 12.50 165 .50 114 .25 133 1.00 25 2.7 3.62 168 .75 95 1.38 9.38 264 .7 4.97 25 7.62 15.69 246 .7 3. 600.25 159 2.56 40 3. Pressure classes 900 1500 GLOBE VALVE are offered.7 4.91 201 . 316SS.12 257 .7 4.56 40 3.7 5.50 12.00 102 .50 12.38 9. C MIN. 900 and 1500 Vogt designs.50 12.97 25 7.7 4. 3 150 300 600 GLOBE VALVE forged carbon and stainless steel in 1/4” to 2” sizes.38 9.69 68 5.7 9.38 9.38 9.75 95 1.50 114 . 316SSHF Globe Seats . Unlike many others.38 9.50 114 1.7 3.41 112 .7 6.56 40 11.88 276 .7 .50 165 . tests all pressure boundary parts at one location to insure 150 300 600 GATE VALVE complete satisfaction of customer and N-stamp code requirements. D A B C B C MIN.7 1/2 15 3.30 84 1.50 12.38 289 .38 9.91 201 .56 40 7.7 3.7 5.75 95 1.7 4.00 254 .56 40 3.7 7.7 4.7 4.50 165 . 300.62 15.25 159 2.62 15.7 The following trims are available: Stems .7 6.7 4. 2.25 57 4.7 4.00 25 2.7 3. Globe and Check Bold face numerals are in inches.62 168 .50 12.7 7.97 25 7.50 12.12 28 6.316SS.62 168 .50 12.56 40 8.28 33 10.97 279 .50 89 1.69 68 10.56 116 1.56 65 . Integral HF 2 50 7.00 229 3.56 40 7.7 6.7 1-1/2 40 6.30 84 1.7 4.7 4.03 128 .50 12.44 214 .25 133 1.7 3/4 20 4.50 114 1.00 102 1.62 15. 410SSHF.7 6.7 3/8 10 3.75 197 2.30 84 1. D A B C B C MIN.00 25 2.56 40 8.50 114 1.97 25 7.7 7.62 117 1.50 12.75 197 2.25 57 4.50 12. D A B C MIN.75 197 2.7 3.56 65 .50 89 13.7 7.06 78 .7 Gate Seats .50 12.06 78 . The chart shows dimensions of 900 1500 GATE VALVE also be constructed to Section III requirements.00 102 .31 211 .00 25 6.75 95 1.69 68 4.50 12.25 57 10.38 9.56 40 11.7 4.75 95 1.7 1-1/4 32 6.47 190 .7 4.62 117 1. 150 300 600 CHECK VALVE 900 1500 CHECK VALVE MIN.88 48 13.56 40 3.03 128 . 2 or 3 gate.00 178 1.12 257 .50 12.25 57 4.7 4.97 279 .38 264 .50 12.7 4.50 114 1.75 121 1.25 159 2. 316SSHF 44 1 25 4.38 9.56 40 11.56 65 .62 15.91 201 .50 12.25 57 10.06 78 .38 9.56 40 3.7 4.47 190 .00 102 .75 197 2.50 12.7 7.91 201 .62 15.00 25 6.410SS.00 101 1.7 7.38 289 . GLOBE & CHECK globe and check valves of Class 1.75 197 2. in ASME Section III "N" stamp construction.Flow Control Division Vogt Valves Forged Nuclear Valves – Nuclear Gate.75 95 1.75 121 1. Vogt Valves for Nuclear Service SIZE & TYPE Vogt offers Class 1.38 9.50 12.410SSHF.Integral.00 25 6.50 165 .50 12.38 9.7 4.00 229 3.38 9.50 89 6.56 40 7.12 28 2.50 12.00 25 6.25 57 10.50 114 1.25 159 2.38 9.38 9. manufactures and NPS DN A 1/4 8 3.47 190 .50 114 1.06 78 .56 40 7.50 114 1.31 338 . D A 150.47 190 .25 159 2.38 9.12 155 .25 133 1.50 12.69 68 10. D Refer to pages 116-120 for full materials description.69 68 5.28 33 10.7 3.12 28 6.94 125 . 17-4PH Disc/Gates . If not listed. Trim 304/Flexible Graphite Spiral Wound Gasket Flexible Graphite Packing B7M Bonnet Bolting Hard Faced Seats and Gate (or Disc) Full Rating 316. NACE bolting. TRIM SUFFIX DESIGNATIONS: (Used with series numbers to indicate special characteristics of sour service valves). crevice and general corrosion) and other forms of environmental embrittlement. Fittings: All Vogt fittings noted in the VV200 Catalog meet NACE MR-01-75 requirements from stock. It is an aid in the selection of materials for those “Sour Environment” applications with conditions present which could result in SSC. can be obtained by writing: NACE.Flow Control Division Forged Valves and Fittings – For Sour Service Vogt Valves NACE (National Association of Corrosion Engineers) Standard MR-01-75:(1) A number of outside screw and yoke (OS&Y) and inside screw (ISS) valves utilizing fabrication processes. hardness. carbon dioxide (CO2) and water containing chlorides may also be present in crude oils and gases. P. other than Vogt standard. please make inquiry because most Vogt valve designs can be supplied with one of the trim packages listed. H2O and Chlorides Monel or 13 Cr.Discs and integral seats are hard faced.) Solution Annealed 316 Trim 316/Flexible Graphite Spiral Wound Gasket Flexible Graphite Packing B8MCL1 Bonnet Bolting Hard Faced Seats and Gate (or Disc) Full Rating Soft 13Cr. This environment can lead to degradation of exposed material by weight loss corrosion (pitting. hardness. These valves are carried in stock and are available with written certification to NACE Standard MR-01-75 "SULFlDE STRESS CRACKING (SSC) RESISTANT METALLlC MATERIAL FOR OIL FIELD EQUIPMENT” when specified. Vogt Valve Company takes extreme care to control the manufacturing process for valve trim parts. or Monel 1) MR-01-75 is a material standard—not a design standard. GATE . bolting. 2. O. Vogt NACE valves use bonnet bolting meeting the exposed bolting requirements of NACE MR-01-75. Non Exposed Bolting: Bolting which is exposed to the open atmosphere rather than the sour environment. The standard discusses the sour environment and presents guidelines in the H2S concentration and pressure relationships where SSC can occur in sour gas and sour multiphase systems. TRIM SUGGESTIONS CHART: (For oil/gas sour service environments in -20°F to 800°F temperature range). Copies of MR-01-75. 1. 2) See the individual pages of the VV200 Catalog for Vogt valves available with the various NACE trim packages. Refer to pages 116-120 for full materials description. insulated or equipped with flange protectors or otherwise denied direct exposure to the open atmosphere. 4) CHECK/GLOBE . SUFFIX(2) SPECIAL CHARACTERISTICS ENVIRONMENT SUGGESTED TRIM MBS(3) (Monel) Gasket Monel Trim Monel/Flexible Graphite Spiral Wound H2S and H2O H2S. 45 . welds and materials selected from NACE MR-01-75 are offered. CO2 316 or 13 Cr. In addition to H2S. The disc is solution annealed after machining to assure Rc-22 Max. H2S.Seats and wedge are hard faced and solution annealed after machining to assure Rc-22 Max. Texas 77218. Houston. Flexible Graphite Packing B7M Bonnet Bolting Full Rating H2S. Box 218340. H2O. can be provided at the option of the end user. 3) In multiphase systems significant general corrosion may occur for monel trim at service temperatures above 300°F when CO2. MB8(4) (316SS) MB6 (13 Cr. Vogt offers a number of popular trim packages for their NACE valves processed to the NACE MR-01-75 requirements and noted in the table below. The standard has an excellent listing of ferrous and non-ferrous materials that are resistant to SSC. H2S and Chlorides are present. CO2 and Chlorides Monel or 13 Cr. including revisions. NACE MR-01 75 addresses bolting requirements in two categories: MR-01-75 covers only materials resistant to SSC but other considerations must be recognized and properly dealt with to assure efficient and safe control of hazardous media. H2O. Exposed Bolting: Bolting which in service is exposed directly to the sour environment or which will be buried. 13 Cr. and pressure boundary welds to maintain appropriate chemistry and mechanical properties which are resistant to SSC. from the flowing media and pressure. The Vogt Globe and Angle valve lines provide a variety of design variations to fulfill your requirements. Order by Size and Series Number. The valve packing and bonnet gasket Dimensions are in inches and millimeters. are totally isolated by the bellows Dimensions are subject to change without notice. Flow above the disc is also acceptable. 46 .Flow Control Division Vogt Valves Globe and Angle Valve Section – Pages 46-87 Globe and Angle valves are suitable for throttling as well as shut-off. BOLTED BONNET GLOBE VALVE BOLTED BONNET BELLOW SEAL GLOBE VALVE BOLTED BONNET ANGLE VALVE Bellowseal globe valves are suitable for applications requiring total containment of the flowing media frequently necessary to protect the environment and to eliminate the loss of hazardous and/or costly fluids. They are customarily installed so that the media pressure and preferred flow direction is under the disc (as illustrated). The packing and gasket are incorporated in the valve to serve in a “back up” role only. Flow characteristics can be determined from the Cv Factors listed on pages 122 and 123. Flow Control Division Vogt Valves Forged Globe Valves ■ ■ ■ ■ ■ ■ ■ Class 150 (PN 20) Conventional Port 285 PSI @ 100°F (19.7 BAR @ 38°C) For other ratings see pgs. 112-115 A105 Body/Bonnet 473, 473B, 32473 GLOBE CLASS 150 (PN 20) 473 SERIES NUMBER Trim: 13% Cr. Seat: HF 473F8M Trim: 316 Seat: HF 473MM Trim: Monel Seat: HF 473MB8 Trim: 316 Seat/Disc: HF 473B (Bellows) Stem: 13% Cr. Disc: 316HF Bellows: 316L Disc/Seat: HF A1350 LF2 Body/Bonnet 32473 Trim: 13% Cr. Seat: HF Meets API-602 required wall thicknesses. MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bellows Globe Valve Dimensions Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc (Except Bellows Valve) Integral Hard Faced Seat ASME B16.34 Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Flanged Ends 1/16" R.F. NPS DN 1/2 15 4.25 108 6.62 168 6.19 157 .50 12.7 4.00 102 6.8 3.1 Valve flanges conform to ASME Standard B16.5 and end-to-end dimensions conform to ASME Standard B16.10. 3/4 20 4.62 117 6.62 168 6.19 157 .50 12.7 4.00 102 8.0 3.6 1 25 5.00 127 8.44 214 7.81 198 .75 19.1 4.75 121 11.9 5.4 1-1/2 40 6.50 165 10.38 264 9.47 241 1.28 32.5 5.75 146 25.0 11.4 Bellows Globe Valve 2 50 8.00 203 10.88 276 9.81 249 1.53 38.9 7.00 178 38.0 17.3 For Cv factors see page 123, Valve Matrix J. Refer to pages 116-120 for full materials description 47 1/2 15 4.25 108 6.32 161 6.13 156 .50 12.7 4.00 102 7.0 3.2 3/4 20 4.62 117 6.88 157 6.62 168 .75 19.1 4.75 121 11.6 5.3 1 25 5.00 127 6.88 157 6.62 168 .75 19.1 4.75 121 11.7 5.3 1-1/2 40 6.50 165 10.00 254 9.50 271 1.53 38.9 7.00 178 25.3 11.5 2 50 8.00 203 10.00 254 9.50 271 1.53 38.9 7.00 178 38.6 17.5 Cv factors for Bellows valve see page 123, Valve Matrix K. Flow Control Division Vogt Valves Forged Globe Valves Class 300 (PN 50) ■ ■ ■ ■ ■ ■ ■ Conventional Port 740 PSI @ 100°F (51.0 BAR @ 38°C) For other ratings see pgs. 112-115 A105 Body/Bonnet 483, 483B, 32483 GLOBE CLASS 300 (PN 50) 483 SERIES NUMBER Trim: 13% Cr. Seat: HF 483F8M Trim: 316 Seat: HF 483MM Trim: Monel Seat: HF 483MB8 Trim: 316 Seat/Disc: HF 483B (Bellows) Stem: 13% Cr. Disc: 316HF Bellows: 316L Disc/Seat: HF A350 LF2 Body/Bonnet 32483 Trim: 13% Cr. Seat: HF Meets API-602 required wall thicknesses. Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc (Except Bellows Valve) Integral Hard Faced Seat ASME B16.34 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bellows Globe Valve Dimensions Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Flanged Ends 1/16" R.F. Bellows Globe Valve NPS DN 1/2 15 6.00 152 6.62 168 6.19 157 .50 12.7 4.00 102 8.5 3.9 Valve flanges conform to ASME Standard B16.5 and end-to-end dimensions conform to ASME Standard B16.10. 3/4 20 7.00 178 6.62 168 6.19 157 .50 12.7 4.00 102 11.4 5.2 1 25 8.00 203 8.44 214 7.81 198 .75 19.1 4.75 121 15.6 7.1 1-1/2 40 9.00 229 10.38 264 9.47 241 1.28 32.5 5.75 146 29.9 13.6 2 50 10.50 267 10.88 276 9.81 249 1.53 38.9 7.00 178 44.0 20.0 For Cv factors see page 123, Valve Matrix J. Refer to pages 116-120 for full materials description. 48 1/2 15 6.00 152 6.32 161 6.13 156 .50 12.7 4.00 102 8.7 3.9 3/4 20 7.00 178 6.88 175 6.62 168 .75 19.1 4.75 121 15.1 6.9 1 25 8.00 203 6.88 175 6.62 168 .75 19.1 4.75 121 15.5 7.0 1-1/2 40 9.00 229 10.00 254 9.50 271 1.53 38.9 7.00 178 40.2 18.2 2 50 10.50 267 10.00 254 9.50 271 1.53 38.9 7.00 178 43.8 19.9 Cv factors for Bellows valve see page 123, Valve Matrix K. Flow Control Division Vogt Valves Forged Globe Valves ■ ■ ■ ■ ■ ■ ■ Class 600 (PN 110) Conventional Port 1480 PSI @ 100°F (102.1 BAR @ 38°C) For other ratings see pgs. 112-115 493 493, 493B, 32493 GLOBE CLASS 600 (PN 110) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc (Except Bellows Valve) Integral Hard Faced Seat ASME B16.34 SERIES NUMBER Trim: 13% Cr. Seat: HF 493F8M Trim: 316 Seat: HF 493MM Trim: Monel Seat: HF 493MB8 Trim: 316 Seat/Disc:HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bellows Globe Valve Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Flanged Ends: 1/4" R.F. 493B (Bellows) Stem: 13% Cr. Disc: 316 HF Bellows: 316L Disc/Seat: HF A350 LF2 Body/Bonnet Trim: 13% Cr. Seat: HF Meets API-602 required wall thicknesses. Dimensions Size A-End-to-End 32493 B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Bellows Globe Valve NPS DN 1/2 15 6.50 165 6.62 168 6.19 157 .50 12.7 4.00 102 8.6 3.9 3/4 20 7.50 190 6.62 168 6.19 157 .50 12.7 4.00 102 10.8 4.9 Valve flanges conform to ASME Standard B16.5 and end-to-end dimensions conform to ASME Standard B16.10. 49 1 25 8.50 216 8.44 214 7.81 198 .75 19.1 4.75 121 17.0 7.7 1-1/2 40 9.50 241 10.38 264 9.47 240 1.28 32.5 5.75 146 33.5 15.2 2 50 11.50 292 10.88 276 9.81 249 1.53 38.9 7.00 178 46.0 20.9 For Cv factors see page 123, Valve Matrix J. 1/2 15 6.50 165 6.32 160 6.13 156 .50 12.7 4.00 102 8.8 4.0 3/4 20 7.50 190 6.88 175 6.62 168 .75 19.1 4.75 121 14.5 6.6 1 25 8.50 216 6.88 175 6.62 168 .75 19.1 4.75 121 16.6 7.6 1-1/2 40 9.50 241 10.00 254 9.50 241 1.53 38.9 7.00 178 43.8 19.9 2 50 11.50 292 10.00 254 9.50 241 1.53 38.9 7.00 178 49.3 22.4 For Cv factors for Bellows valve see page 123, Valve Matrix K. 1 5.38 264 1.5 1-1/2 40 9.00 152 6.19 30.1 BAR @ 38°C) 22493CL 22493MT Stem: Hastelloy C Trim: Monel Stem: Hastelloy C+ Trim: Monel/Teflon Disc: Teflon Insert Flanged Ends Class 300: 1/16" R.8 4. Valve flanges conform to ASME Standard B16.5 7.06 205 .44 214 8.1 1-1/2 40 9.31 160 . 50 Series 22493CL 2 50 10.44 36.6 7.62 168 6.2 21.06 205 .88 276 10. Valve Matrix L. B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Disc with Teflon Insert Bold face numerals are in inches and pounds.00 102 8.00 102 12. CLASS 600 (PN 110) For other ratings see pgs.19 259 1. .Flow Control Division Vogt Valves Forged Globe Valves – For Water-Free Chlorine Service ■ ■ ■ ■ ■ Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Solid Disc or Teflon-Inserted Disc ■ Renewable Seats ■ ASME B16. 22493 GLOBE CLASS 300 (PN 50).06 281 10.2 5.50 292 11.44 36.75 121 15.19 30.50 165 6.75 146 33.50 190 6.0 15.00 203 8.31 160 .3 20.9 4.50 267 10.62 168 6.00 178 46.00 102 13.66 16.75 121 16.34 Class 300 (PN 50) Conventional Port 740 PSI @ 100°F (51.6 7.0 Refer to pages 116-120 for full materials description.1 1/2 15 6.5 3.81 249 1.50 216 8.39 9.F.F.39 9.10.9 3/4 20 7.66 16.44 214 8.5 and end-to-end dimensions conform to ASME Standard B16.31 157 .38 264 9.4 5.39 9.3 Valves contain TEFLON — maximum temperature 500°F.00 229 10. Flanged Ends Class 600: 1/4" R.9 4.7 7.6 3/4 20 7.00 102 8.9 1 25 8.62 168 6.75 146 35. Series 22483CL NPS DN 1/2 15 6.9 4.8 4.50 241 10. 112-115 Conventional Port 1480 PSI @ 100°F (102.00 178 44.39 9.00 178 6. Blue numerals are in millimeters and kilograms.2 5.6 1 25 8.9 4.81 249 1. Dimensions Size Chlorine Service Temperatures Not to Exceed 300°F A-End-to-End Meets API-602 required wall thicknesses.38 264 9.62 168 6.31 157 .0 BAR @ 38°C) A105 Body/Bonnet SERIES NUMBER 22483CL Stem: Hastelloy C Trim: Monel Class 600 (PN 110) 22483.0 3.6 15. For Cv factors see page 123.9 2 50 11. 1 BAR @ 38°C) For other ratings see pgs. 10403 GLOBE CLASS 600 (PN 110) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Renewable Seats ASME B16.62 498 2.8 9. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16.6 7. Refer to pages 116-120 for full materials description.5 8.Flow Control Division Vogt Valves Forged Globe Valves Class 600 (PN 110) ■ ■ ■ ■ ■ ■ ■ 1480 PSI @ 100°F (102.75 248 76. 51 1/2 15 6.22 56.1 24.00 203 57.00 305 170. 1 25 8.12 384 1.75 248 97.50 292 18.9 . 99.7 4.2 Bold face numerals are in inches and pounds.50 12.00 356 22. Valve Matrix M.00 229 14.00 330 20.72 18.1 25.81 71.50 241 16.56 370 13.75 121 19.1 1-1/4 32 9.75 146 31.3 5.94 303 . 2-1/2 65 13.2 8.56 268 10.00 533 2.2 3 80 14.4 For Cv factors see page 123.44 36.88 353 1.19 30. 112-115 SERIES NUMBER 10403 Trim: 13% Cr.9 1-1/2 40 9.34 Flanged Ends: 1/4" R.6 9.19 259 .7 44.06 281 .4 13.94 329 11.69 297 11.50 165 10.00 406 15. 77.97 24. Blue numerals are in millimeters and kilograms.5 and end-to end dimensions conform to ASME Standard B16.10.75 349 220.50 216 12.06 459 17.81 529 19.12 435 1.88 47.4 12.6 2 50 11.F.9 3/4 20 7.2 14. Meets API-600 required wall thicknesses.50 190 11.2 34.25 565 21.00 178 53. 9 1 25 4.75 120 8. 52 1-1/2 40 7. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.8 7.7 4.88 174 6.75 196 10.75 95 6.00 254 9.5 13.62 117 6.8 For Cv factors see page 123.62 168 .7 2 50 7.50 12.00 177 30. Blue numerals are in millimeters and kilograms.53 38.5 3.75 196 10.62 168 .00 177 30. Valve Matrix K.62 117 6.0 4.34 Bold face numerals are in inches and pounds. Disc: 316 HF Bellows: 316L Seats: HF Dimensions Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Multi-Ply Bellows Hard Faced Disc Integral Hard Faced Seat ASME B16.50 241 1. 1/2 15 3.Flow Control Division Vogt Valves Forged Globe Valves – Bellowseal Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ ■ Conventional Port 1975 PSI @ 100°F (136.50 241 1.88 174 6.5 13.0 4.7 3.75 120 8.13 155 .0 2.2 BAR @ 38°C) For other ratings see pgs.53 38.00 102 5.32 160 6. 112-115 12141B BELLOWS – GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 12141B SW12141B Trim: Stem: 13% Cr.7 .75 19.8 7.75 19.00 254 9.2 3/4 20 4. 75 146 21.88 251 . Refer to pages 116-120 for full materials description.8 4.00 102 6. Valve Matrix N.66 16.38 264 9. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/2 15 4.75 121 9. Manual. Blue numerals are in millimeters and kilograms.25 159 10.06 205 . Dimensions Bold face numerals are in inches and pounds.97 24.6 5. + Valves contain TEFLON — maximum temperature 500°F. 53 1 25 6.Flow Control Division Vogt Valves Forged Globe Valves – For HF Alkylation Service Class 600 (PN 110) ■ ■ ■ ■ ■ Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Solid Disc or Loose Teflon-Inserted Disc ■ Renewable Seat Full Port 1480 PSI @ 100°F (102.39 9.1 BAR @ 38°C) For other ratings see pgs.4 9.1 2.9 4.44 214 8. 43241MTP GLOBE CLASS 600 (PN 110) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 43241MMP+ Trim: Monel 43241MTP+ Trim: Monel (3/4 only) Disc: Teflon Insert Disc with Teflon Insert Listed in Phillips Petroleum Company’s HF Alkylation Process Design Spec.1 4.31 160 .62 117 8. 112-115 43241MMP.1 .3 For Cv factors see page 123.62 168 6.00 102 5.7 3/4 20 4. Refer to pages 116-120 for full materials description.47 317 1.28 287 1.00 178 29. 112-115 42241MTG.39 9.6 7. Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Double Packing Lantern Ring Grease Injector Teflon-Inserted Disc Renewable Seat 1/2 15 3.75 121 10.2 BAR @ 38°C) For other ratings see pgs.28 210 8.2 .6 For Cv factors see page 123. SW42241HF2 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 42241MTG+ SW42241MTG+ Trim: Monel Disc: Teflon Insert SW42241HF2+ (Sizes 1/2 .1) Trim: Monel Disc: Teflon Insert HYDROFLUORIC ACID (HF) ALKYLATION VALVES. UOP APPROVED.00 102 6.66 16.8 4.7 3/4 20 4.39 9.44 36. Valve Matrix L.9 4.7 9.9 4.75 248 .62 117 10.94 303 11.19 30.00 203 .75 146 21.2 5.9 2.25 159 11. Bold face numerals are in inches and pounds.28 210 8.19 259 9.00 203 . 54 1-1/2 40 6.00 102 8. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON — maximum temperature 500°F.00 102 5.Flow Control Division Vogt Valves Forged Globe Valves – For HF Alkylation Service ■ ■ ■ ■ ■ ■ ■ ■ ■ Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.2 4.75 197 13.0 1 25 4. Blue numerals are in millimeters and kilograms.75 95 8.9 2 50 7.6 3.0 13.16 334 12. 62 117 8. Refer to pages 116-120 for full materials description.00 102 4.2 1/2 15 3.9 7.53 38. Seat: HF 32141F8M 32141MB8 SW32141F8M Trim: 316 Seat: HF SW32141MB8 Trim: 316 Disc/Seat: HF HYDROFLURIC ACID (HF) ALKYLATION VALVES. 112-115 12141.0 3/4 20 4.62 168 6.75 146 20.75 121 8.47 241 1.7 4.00 102 4.38 264 9.8 2.50 12.2 9.3 2.7 3.7 4.34 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bold face numerals are in inches and pounds.75 95 6.88 276 9.00 102 5. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/4 8 3.75 95 6.1 4.62 168 6.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) Conventional Port ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136. Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.9 9.19 157 .2 2 50 7.75 197 10.28 32.75 95 6.5 5.44 214 7.75 146 20.00 102 4.38 264 9.25 159 10. 32141 GLOBE CLASS 800 (PN 130) SERIES NUMBER Body/Bonnet Threaded A105 12141 12141T+ 12141FHF Socket Weld SW12141 SW12141T+ Trim: 13% Cr. Disc/Seat: HF SW12141HF6 SW12141HF7 Trim: 13% Cr.28 32.3 1 25 4.6 .9 13.81 198 .75 19.62 168 6.2 BAR @ 38°C) For other ratings see pgs.19 157 . Seat: HF 12141F8M 12141MB8 A350 LF2 SW12141F8M Trim: 316 Seat: HF SW12141MB8 Trim: 316 Disc/Seat: HF 12141MM SW12141MM Trim: Monel Seat: HF 32141 SW32141 Trim: 13% Cr. Valve Matrix J.5 5.50 12. UOP APPROVED.19 157 .47 241 1. 1-1/2 40 6.81 249 1.0 2.8 2.7 4.62 168 6.2 +Valves contain TEFLON – maximum temperature 500°F.50 12.00 178 29.7 4.00 102 6. Blue numerals are in millimeters and kilograms. Seat: HF SW12141FHF Trim: 13% Cr.5 For Cv factors see page 123.25 159 10.19 157 . 55 3/8 10 3.9 1-1/4 32 6.50 12. 7 4.7 4.8 2.53 38.00 102 6.19 157 .75 146 20.62 168 6.50 12.75 95 6.5 1-1/2 40 6. 3 (2-1/4% Cr.00 178 29. 2 50 7.) Socket Weld SW12351 Trim: 13% Cr.62 168 6.0 3/4 20 4. Refer to pages 116-120 for full materials description.28 32.19 157 .44 214 7.00 102 4. Seat: HF F22.28 32. 12551.9 1-1/4 32 6.88 276 9.2 3/8 10 3.00 102 4.0 2.62 168 6.8 2.62 168 6.3 2. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight +Valves contain TEFLON – maximum temperature 500°F.00 102 4.38 264 9.3 1 25 4.4 BAR @ 38°C) 82501 SW82501 Trim: 316H Bold face numerals are in inches and pounds.75 146 20.19 157 . Valve Matrix J.5 5.47 241 1.47 241 1.25 159 10.9 9.5 5. 2 12351 (1-1/4% Cr.9 BAR @ 38°C) ■ ■ ■ ■ ■ ■ ■ 12351.75 95 6.38 264 9.75 19.62 117 8. Cl.81 198 .19 157 .81 249 1.50 12.00 102 5.2 For Cv factors see page 123.9 13.34 SW12551 Trim: 13% Cr.7 4. Blue numerals are in millimeters and kilograms.25 159 10.1 4. Seat: HF 1920 PSI @ 100°F (132. 56 1/4 8 3.75 197 10.2 9. 112-115 SERIES NUMBER Body/Bonnet Threaded F11.50 12.6 .50 12.7 4.9 7.75 95 6.7 3.2 1/2 15 3.) 12551 F316/F316L 1920 PSI @ 100°F (132.75 121 8. Cl.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) Conventional Port 2000 PSI @ 100°F (137.4 BAR @ 38°C) 12501 SW12501 12501T+ SW12501T+ Trim: 316 F316H Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16. 82501 GLOBE CLASS 800 (PN 130) For other ratings see pgs. 12501. 112-115 Dimensions Bold face numerals are in inches and pounds.12 689 1.8 2 50 7.19 716 27. 1-1/2 40 6.75 578 22.5 5.78 528 .75 121 11.64 702 26.53 38.0 3.25 159 27.03 560 .00 102 7. Blue numerals are in millimeters and kilograms.9 8.00 203 33.3 2.34 D-Seat Diameter E-Handwheel Diameter Weight +Valves contain TEFLON—maximum temperature 500°F.22 539 20.9 3/4 20 4. Valve Matrix J.7 4.7 5.62 117 22.75 95 21.28 32.2 1 25 4.72 679 1.4 BAR @ -198°C) F316/F316L Body/Bonnet SERIES NUMBER Threaded Socket Weld 12501C+ SW12501C+ Trim: 316 12501C GLOBE CLASS 800 (PN 130) For other ratings see pgs.4 BAR @ 38°C) 1920 PSI @ -325°F (132.9 15. 57 1/2 15 3. Refer to pages 116-120 for full materials description.Flow Control Division Vogt Valves Forged Globe Valves – Cryogenic Service to -325°F (-198°C) Class 800 (PN 130) Conventional Port 1920 PSI @ 100°F (132.7 10.00 102 6.50 12.4 .75 19.3 For Cv factors see page 123. NPS DN Size A-End-to-End B-Open C-Closed ■ ■ ■ ■ ■ ■ ■ ■ Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Seat Extended Bonnet ASME B16.75 146 23.00 102 21.78 528 .22 539 20.50 12.75 197 28.7 4.1 4. 8 8. Blue numerals are in millimeters and kilograms.00 50.1 4.75 146 21.75 121 9.0 102 6.2 BAR @ 38°C) For other ratings see pgs.5 2 50 9.00 178 29.28 32.6 9.78 198 .75 19.38 264 9.5 5. Seat: HF 13141 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet 13141FHF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.47 240 1.47 240 1.19 310 2. Disc/Seat: HF Bold face numerals are in inches and pounds.62 168 6.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ Full Port 1975 PSI @ 100°F (136.7 4.00 102 5. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.06 332 12.34 SW13141FHF Trim: 13% Cr.7 1-1/4 32 6.81 249 1.1 1 25 6.50 216 7.3 3/4 20 4.00 203 53.4 For Cv factors see page 123.25 159 10.75 197 10.28 32.88 276 9.12 155 . 1/2 15 4.38 264 9. 58 1-1/2 40 7.53 38.4 24.00 229 13.25 159 10.4 9.5 5.50 12.62 117 8. 112-115 SERIES NUMBER Threaded Socket Weld 13141 SW13141 Trim: 13% Cr.1 2.2 .1 4.9 7.75 146 20.9 13. Valve Matrix P. 2 BAR @ 38°C) For other ratings see pgs. 59 1-1/2 40 7.34 161 .00 203 30.4 9.19 310 1. 23141HF5 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld – SW23141HF4 – SW23141HF5 Trim: Monel HYDROFLUORIC ACID (HF) ALKYLATION VALVES.6 7.19 259 1.75 121 9.00 178 20. Blue numerals are in millimeters and kilograms.97 24.1 1 25 6.6 5.39 9.38 264 9.44 214 8.62 117 8.Flow Control Division Vogt Valves Forged Globe Valves – For HF Alkylation Service Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136. 112-115 23141HF4.34 Bold face numerals are in inches and pounds.1 2. Valve Matrix N.44 36.9 4.66 16.06 205 . Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Renewable Seat ASME B16.8 8.25 159 10.7 For Cv factors see page 123.88 276 10.75 146 21. 1/2 15 4.00 102 6.4 2 50 9.3 3/4 20 4.8 4.6 . Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description. UOP APPROVED.75 197 10.6 9.1 4.88 47.06 332 12.88 251 .62 168 6.00 229 13.0 13.00 102 5. 31 160 . Blue numerals are in millimeters and kilograms.1 13.75 95 6.2 3/8 10 3.75 197 10.25 83 4.9 4.66 16.31 160 .75 95 6.06 205 .8 2.75 121 8.8 9.62 102 8.6 7.00 102 6.19 30.34 SW22141MM Trim: Monel Bold face numerals are in inches and pounds. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.25 121 10.00 102 4.44 214 8.00 102 5.00 178 29.75 95 6.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) Conventional Port ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136.9 4.62 168 6.0 For Cv factors see page 123.2 5.39 9.38 264 9.25 83 4.2 BAR @ 38°C) For other ratings see pgs.25 121 10.75 146 20. 112-115 SERIES NUMBER Threaded Socket Weld 22141F8M SW22141F8M Trim: 316 22141 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet 22141MM Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Renewable Seat ASME B16. 1/4 8 3.8 4.31 160 .1 9.9 3.19 259 1.2 3/4 20 4.38 264 9.88 276 10.78 248 1.75 146 20. Valve Matrix L.39 9.9 4.4 1-1/2 40 6.44 36.9 2. 60 1-1/4 32 6.39 9.0 2.31 160 .9 3.1 2 50 7.62 168 6.3 1 25 4.62 168 6.62 168 6.2 1/2 15 3.2 5.8 2.19 30.39 9.78 248 1.2 . 00 102 5.00 102 6.1 9.0 5.38 264 9.8 9.00 178 29.9 3.44 214 8. Refer to pages 116-120 for full materials description.62 168 6.06 205 .34 161 .2 3/4 20 4.9 4.62 168 6.19 36.39 9.75 95 6.0 For Cv factors see page 123.78 248 1.1 2 50 7.9 4.75 146 20.75 121 8.19 259 1.9 2.2 3/8 10 3.2 .44 36.25 159 10.9 4.0 5.75 197 10.25 159 10.38 264 9.3 1 25 4.39 9.25 83 4. Blue numerals are in millimeters and kilograms.75 95 6.78 248 1. 61 1-1/4 32 6.66 16.6 7.34 161 .62 117 8.34 Conventional Port 1975 PSI @ 100°F (136.75 95 6. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight +Valves contain TEFLON—maximum temperature 500°F.8 2.2 1/2 15 3. 1/4 8 3.1 13. 112-115 22141 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 22141CL SW22141CL Stem: Hastelloy C Trim: Monel 22141MT+ SW22141MT+ Stem: Hastelloy C Trim: Monel Disc: Teflon Insert Chlorine Service Temperatures Not to Exceed 300°F Disc with Teflon Insert Bold face numerals are in inches and pounds.62 168 6.8 2.2 BAR @ 38°C) For other ratings see pgs. Valve Matrix L.0 2.00 102 4.19 36.34 161 .8 4.39 9.34 161 .75 146 20.62 168 6.Flow Control Division Vogt Valves Forged Globe Valves – For Water-Free Chlorine Service ■ ■ ■ ■ ■ Class 800 (PN 130) Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Solid Disc or Teflon-Inserted Disc ■ Renewable Seats ■ ASME B16.4 1-1/2 40 6.39 9.9 3.25 83 4.88 276 10. 75 19 8.62 168 6.00 178 2.88 99 2.00 51 .7 .00 25 .00 178 2.2 BAR @ 38°C) Size For other ratings see pgs.44 11 4. For Cv factors see Page 123 Valve Matrix Q.00 152 2.50 13 6.94 75 Refer to Pages 116-120 for full materials description. 62 .00 51 .90 48.47 37 . Seat: HF 12141 GLOBE EXTENDED BODY CLASS 800 (PN 130) A105 Body/Bonnet A TYPE ENDS Integrally Reinforced Male Couplet Female Threaded B C G H ST 12141 TT 12141 Trim: 13% Cr.75 44 1-1/2 40 6.34 L M N P R S T NPS DN 1/2 15 7.06 281 10.47 249 5.84 21.38 264 9.31 8 4.00 152 2.50 114 1.32 33.50 114 1.81 198 4.81 46 . 112-115 SERIES NUMBER CT 12141 Trim: 13% Cr.00 102 .75 146 1.Flow Control Division Vogt Valves Forged Globe Valves – Extended Body Dimensions Class 800 (PN 130) 1975 PSI @ 100°F (136.19 157 4.75 19 .3 1.38 60 2 50 6. Seat: HF Trim: 13% Cr.05 26.47 37 1.97 25 1.3 .56 65 1.25 133 1. Seat: HF Male Socket Weld Female Threaded Male Threaded Female Threaded J K ■ ■ ■ ■ ■ ■ ■ Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.52 13 .94 49 1.44 37 1 25 5.56 40 .44 214 7.38 60 1.44 11 6.00 102 .28 33 10.44 11 5.12 79 1.5 .65 17 .50 165 3.75 121 1.56 40 1.97 25 1.50 13 6.62 168 6.00 254 8.56 14 6.53 39 11.31 59 1.22 56 3.00 203 2.75 19 .22 31 1.81 21 .19 157 4.75 146 2.00 51 1.72 44 2.44 37 3/4 20 7.12 79 2.50 165 3. 94 23.00 178 31.4 14.38 3.81 173 6.44 214 7.4 1-1/2 40 6.3 .88 276 9. of Turns 3 4-1/2 5 6-1/2 8 Dimensions Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose V-Port Disc Integral Hard Faced Seat Dial & Indicator ASME B16.81 249 1.54 9.6 4.75 121 9.7 4.00 102 5.2 BAR @ 38°C) For other ratings see pgs.1 2.91 201 .65 14.46 2. Seat: HF 12443 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet Size 1/2 3/4 1 1-1/2 2 Cv Factor 1.53 166 .3 3/4 20 4.00 102 5.62 15. Blue numerals are in millimeters and kilograms.7 4.6 2 50 7.19 30.9 5.2 4.75 95 6.) No.81 173 6.44 11.2 7.0 8.38 264 9.75 146 19.Flow Control Division Vogt Valves Forged Globe Valves – For Flow Control Service Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ ■ Conventional Port 1975 PSI @ 100°F (136. NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.62 117 8.75 197 10. 112-115 SERIES NUMBER Threaded Socket Weld 12443 SW12443 Trim: 13% Cr.25 159 10.60 (Approx. 63 1/2 15 3.4 2.34 Bold face numerals are in inches and pounds.44 164 .38 4.00 102 6.5 1 25 4.78 248 . 25 83 4.75 95 6.00 102 5.69 170 6.2 1 25 4. of Turns 3-1/2 3-1/2 3-1/2 3-1/2 5-1/2 Bold face numerals are in inches and pounds.9 .8 3.8 3.8 2.56 .19 4. Stem/Seat: HF Cv Factor .38 162 .38 162 .6 2. 112-115 SERIES NUMBER Threaded Socket Weld 22461 SW22461 Trim: 13% Cr.1 1/2 15 3.2 BAR @ 38°C) For other ratings see pgs.4 4.69 170 6.00 102 6.99 1.00 102 4.) No.50 (Approx.38 162 . Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description. 64 1/4 8 3.68 .55 .6 3.25 6.69 170 6.0 2.19 4.62 219 8.75 95 6.8 4.38 162 .06 205 .3 3/4 20 4.34 22461FHF Size 1/4 3/8 1/2 3/4 1 SW22461FHF Trim: 13% Cr.25 83 4.69 170 6. 22461 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Needle Point Flow Control Renewable Seat ASME B16.9 2.75 95 6.8 4. Blue numerals are in millimeters and kilograms.75 121 8.19 4.62 117 8.2 3/8 10 3.Flow Control Division Vogt Valves Forged Globe Valves – For Flow Control Service ■ ■ ■ ■ ■ ■ ■ Class 800 (PN 130) Needle Point Stem/Seat 1975 PSI @ 100°F (136.19 4. 2 3/4 20 1.7 4.2 BAR @ 38°C) For other ratings see pgs.5 5.3 . Blue numerals are in millimeters and kilograms.1 4.62 92 13.12 79 10.19 157 .34 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.62 41 6.62 168 6.62 41 6.12 79 10.8 15.38 264 9.5 2 50 3..8 8.19 157 .50 12.44 214 7.00 102 5.8 2.75 44 6.75 146 18.9 1-1/4 32 3.53 242 1.2 2.53 242 1.Flow Control Division Vogt Valves Forged Angle Valves Class 800 (PN 130) Conventional Port ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136.53 38.28 32. Seat: HF Bold face numerals are in inches and pounds.75 19.50 12. 1/4 8 1.7 8.19 157 .28 32.19 310 1.25 337 12.31 59 8.7 4.7 4.7 4.0 2.38 264 9.50 12.62 168 6.00 102 5.00 203 33.7 3.9 8.19 157 .75 121 8. 65 1-1/2 40 3.00 102 4.81 198 .62 168 6. Dimensions Size Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.75 146 18.3 1/2 15 1.3 3/8 10 1. Valve Matrix S.5 5.4 1 25 2. 112-115 1971 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 1971 SW1971 Trim: 13% Cr.50 12.00 102 5.62 41 6.62 168 6.5 For Cv factors see Page 123.0 2. 8 2 50 7.00 102 4.2 1/2 15 3.00 203 7.2 BAR @ 38°C) For other ratings see pgs.88 149 .28 32.2 13.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ Conventional Port 1975 PSI @ 100°F (136.00 102 4.75 121 8.8 2.50 12.3 8.31 160 5.7 4.75 95 6.22 260 9.00 102 6.44 291 10.50 12.00 102 4.7 . Dimensions Size Round Bolted Bonnet Spiral Wound Gasket Inside Screw Stem Screw Gland Loose Disc Integral Hard Faced Seat ASME B16.1 4.75 19. Valve Matrix J.00 178 30.5 For Cv factors see Page 123. Seat: HF Bold face numerals are in inches and pounds.00 102 4.38 264 1.28 32.7 4.31 160 5.88 149 .1 3/4 20 4.5 3.6 2.50 12.2 1 25 4.31 186 .7 4.88 149 . 1/4 8 3.22 260 9.7 4.75 146 19.75 95 6.53 38. 66 1-1/2 40 6.75 197 11.75 95 6.25 159 10.50 12.75 146 20.88 149 .25 159 10.31 160 5.5 5.9 9.34 237 1.8 2.9 1-1/4 32 6.9 7. Blue numerals are in millimeters and kilograms.5 5. 112-115 12181 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 12181 SW12181 Trim: 13% Cr.34 237 1.9 2.62 117 8.31 160 5.34 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.2 3/8 10 3. 6 1/2 15 3.4 1-1/4 32 6.19 157 .19 157 .53 38.7 4.38 264 9.28 32.0 1.44 214 7.62 168 6.8 1 25 4.75 19.1 4.50 12.28 32. 67 1-1/2 40 6. 112-115 2821 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet Welded Bonnet Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.62 117 8.50 12.88 276 9.Flow Control Division Vogt Valves Forged Globe Valves ■ ■ ■ ■ ■ ■ Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136. Disc/Seat: HF 2821F8M SW2821F8M Trim: 316 Seat: HF Bold face numerals are in inches and pounds.38 264 9.6 1.50 89 6.5 5.1 6.7 4.5 5. Valve Matrix J.53 242 1. Seat: HF 2821FHF SW2821FHF Trim: 13% Cr.00 102 3.6 3/4 20 3.62 168 6.00 102 3.9 7.25 83 6.19 157 .75 146 15.8 10.7 4. 1/4 8 3.53 242 1.8 . Blue numerals are in millimeters and kilograms.9 For Cv factors see Page 123.25 83 6. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.25 159 10.75 121 7.25 159 10.75 197 10.50 12.7 4.2 BAR @ 38°C) For other ratings see pgs.3 6.81 198 .62 168 6.75 146 15.00 178 23.6 1.6 1.50 12.00 102 4.6 3.62 168 6.6 3/8 10 3.81 249 1.25 83 6.19 157 .34 SERIES NUMBER Threaded Socket Weld 2821 SW2821 Trim: 13% Cr.00 102 3.9 2 50 7. Disc/Seat: HF F22 Cl.5 .00 102 9.) 811 SW811 Trim: 13% Cr. Valve Matrix TT.00 178 12.0 15.6 3/4 20 4.0 5. 112-115 Socket Weld SW810 Trim: 13% Cr.) 822 SW822 Trim: 13% Cr.12 232 .00 51 12.00 102 9.75 146 8.44 265 1. 68 1-1/2 40 7.0 3.Flow Control Division Vogt Valves Forged "Y" Pattern Globe Valves Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ ■ ■ Full Port 2000 PSI @ 100°F (137. Disc/Seat: HF F11 Cl. Blue numerals are in millimeters and kilograms.12 232 .12 130 10. 2 (1-1/4% Cr.50 190 14.0 3.0 2 50 7. 822 Y PATTERN GLOBE LTD CLASS 800 (PN 130) For other ratings see pgs. Disc/Seat: HF Seal Welded Bonnet Outside Screw & Yoke Bolted Gland Removable Yoke/Operating Mechanism Gate Valve Operating Mechanism Repackable with Endless Packing Rings Loose Hard Faced Disc Integral Hard Faced Seat ASME B16.27 362 2.75 146 8.75 217 5.50 190 14.00 305 33.00 305 32.4 For Cv factors see page 123. 1/2 15 4.27 362 2. 3 (2-1/4% Cr.75 217 5.6 1 25 5. 811.9 BAR @ 38°C) SERIES NUMBER Body/Bonnet Threaded A105 810 810.0 14. Dimensions NPS DN Size A-End-to-End B-Center-to-Top C-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.34 LTD Pressure Class Bold face numerals are in inches and pounds.00 51 12.12 28 7. 56 243 1.25 83 6.9 3/4 20 3.5 5.34 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.19 157 .8 .53 38.25 83 6.9 1/2 15 3.50 216 7.62 168 6.3 12.5 5.75 19.1 1.44 265 9.28 32.78 198 .3 For Cv factors see Page 123.25 159 10.50 12.28 32.50 12.7 4.00 102 4.0 2 50 7. Seat: HF Bold face numerals are in inches and pounds.75 121 8.19 157 .7 8.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) ■ ■ ■ ■ ■ ■ ■ Conventional Port 1975 PSI @ 100°F (136.00 102 4.75 146 18.8 1-1/4 32 6.4 3.50 89 6.75 146 17.62 168 6.00 102 4.9 7.19 157 .56 243 1.0 1 25 4.7 4.75 197 10.1 1.25 159 10. 112-115 801 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 801 SW801 Trim: 13% Cr.88 251 1.62 117 8.00 178 28.7 4.62 168 6.44 265 9.3 8.62 168 6.50 12.9 3/8 10 3.00 102 4.2 BAR @ 38°C) For other ratings see pgs. 69 1-1/2 40 6.7 4.3 2.25 83 6. 1/4 8 3.19 157 .1 4. Blue numerals are in millimeters and kilograms.88 276 9.1 1. Valve Matrix J. Dimensions Size Union Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.50 12. 1 1.00 102 3.28 32.9 1.5 .31 160 5.2 BAR @ 38°C) For other ratings see pgs.50 89 6.0 3.9 7.41 290 10.93 201 7.75 121 8.75 146 17.00 102 4.50 12.8 3/8 10 3.25 260 9.38 238 1.8 2 50 7.1 7. Seat: HF Bold face numerals are in inches and pounds.9 1.28 185 .25 260 9.7 4.9 1.5 5.7 8.6 1-1/4 32 6.00 102 3.88 149 .31 160 5. Dimensions Size Union Bonnet Spiral Wound Gasket Inside Screw Stem Screw Gland Loose Disc Integral Hard Faced Seat ASME B16. 1/4 8 3. 70 1-1/2 40 6. 112-115 851 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 851 SW851 Trim: 13% Cr.34 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.1 4.53 38.00 178 29.88 149 .50 12. Blue numerals are in millimeters and kilograms.31 160 5.25 83 6.75 19.62 117 7.25 83 6.7 13.7 4.5 5.00 102 3. Valve Matrix J.31 160 5.8 3/4 20 3.0 For Cv factors see Page 123.7 4.9 1 25 4.25 159 10.50 12.25 159 10.Flow Control Division Vogt Valves Forged Globe Valves Class 800 (PN 130) Conventional Port ■ ■ ■ ■ ■ ■ ■ 1975 PSI @ 100°F (136.8 1/2 15 3.88 149 .75 197 11.7 4.88 149 .25 83 6.75 146 17.28 32.50 12.44 265 1.38 238 1. 88 47.81 71.00 229 18.1 1-1/4 32 6.4 12.25 184 16.8 9.75 248 85.4 .19 30.81 275 10. Bold face numerals are in inches and pounds.34 Meets API-600 required wall thicknesses.25 235 .81 529 19.75 298 11.00 406 15.25 565 21.50 12. 71 2-1/2 65 10.6 9.75 248 57.31 262 .2 1-1/2 40 7.3 5.2 8.50 343 1.50 165 14.Flow Control Division Vogt Valves Forged Globe Valves ■ ■ ■ ■ ■ ■ ■ Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.8 13.72 18.00 127 11. 10103 GLOBE CLASS 800 (PN 130) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Renewable Seat ASME B16.06 383 1.4 13.12 435 1.00 305 128.50 114 10.6 7.1 3 80 13.22 56.3 8.00 178 28.00 330 22. Refer to pages 116-120 for full materials description. Valve Matrix M.0 For Cv factors see Page 123.19 284 . Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/2 15 3.1 25.2 BAR @ 38°C) For other ratings see pgs.0 18. 58.62 92 9.9 39.75 146 19. 112-115 SERIES NUMBER Threaded Socket Weld 10103 SW10103 Trim: 13% Cr.44 36.00 203 40.00 533 2.75 349 188.9 2 50 9. Blue numerals are in millimeters and kilograms. 85.75 121 12.97 24.6 5.7 3/4 20 4.06 357 13.62 498 2.06 458 17.8 1 25 5.62 244 9.7 4.25 260 20. 00 254 16. Valve Matrix V.3 7.00 229 15.3 54.50 38.50 12.00 305 19.12 562 1.97 24.00 584 22.7 7.F.75 349 230 104. Ring Joint Faces Dimensions Size Flanged Ends 1/4" R.69 424 1.5 BAR @ 38°C) For other ratings see pgs.2 27.00 178 60.12 333 12.00 203 78.72 18.00 279 17.34 SERIES NUMBER 10603 Trim: 13% Cr.50 216 13.8 13.75 476 1.6 8.31 440 16.38 365 .1 12. Meets API-600 required wall thicknesses. 10683 GLOBE CLASS 1500 (PN 260) A105 Body/Bonnet RING JOINT FACES 10683 Trim: 13% Cr.12 409 15.4 1-1/4 32 11.5 42.2 9.12 308 .00 305 119. 10603.31 389 .19 30. 3/4 20 9. 112-115 Round Bolted Bonnet Flat Gasket Joint & Ring Gasket Joint Outside Screw & Yoke Bolted Gland Loose Disc Renewable Seat ASME B16.3 1 25 10. Blue numerals are in millimeters and kilograms.10.88 47.2 21.75 502 18.00 381 14.75 248 93.50 368 23.9 Bold face numerals are in inches and pounds.Flow Control Division Vogt Valves Forged Globe Valves ■ ■ ■ ■ ■ ■ ■ Class 1500 (PN 260) Full Port 3705 PSI @ 100°F (255.5 and end-to-end dimensions conform to ASME Standard B16.0 35. Refer to pages 116-120 for full materials description. 2 50 14.2 For Cv factors see page 123.4 . 72 1/2 15 8. NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16.00 178 48.4 1-1/2 40 12. 4 1 25 6.1 .25 184 15.89 404 15.25 438 1. 73 1-1/2 40 9. Valve Matrix V.34 SW1003 Ring Joint Gasket Bonnet (Not illustrated) Trim: 13% Cr.72 18. 1/2 15 4.19 487 1.3 44.50 241 20.Flow Control Division Vogt Valves Forged Globe Valves Class 1500 (PN 260) Full Port ■ ■ ■ ■ ■ ■ ■ 3705 PSI @ 100°F (255.50 343 .7 5.38 289 .8 3/4 20 5.00 229 18.7 52.12 460 17. Bold face numerals are in inches and pounds.97 24.6 13.00 203 44.00 178 29.50 12. 1003 Round Bolted Bonnet Flat Gasket Joint & Ring Gasket Joint Outside Screw & Yoke Bolted Gland Loose Disc Renewable Seat ASME B16.6 8. Meets API-600 required wall thicknesses.00 305 114.75 146 21.5 For Cv factors see page 123.5 BAR @ 38°C) For other ratings see pgs. Blue numerals are in millimeters and kilograms. 1023 GLOBE CLASS 1500 (PN 260) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 1023 SW1023 Trim: 13% Cr.56 370 13.6 9.3 7. 112-115 1003.75 248 98.50 165 14.91 277 .88 478 12.6 9.6 20. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.8 28.19 328 11.75 248 62.44 36.19 513 19.00 127 12.62 295 10.2 1-1/4 32 7.50 114 11.6 2 50 9.19 30.2 9.09 383 1. Seat: HF 15493 GLOBE CLASS 1500 (PN 260) A105 Body/Bonnet 15493F8M Trim: 316 Seat: HF 15493MM Trim: Monel Seat: HF 15493FHF Trim: 13% Cr. Refer to pages 116-120 for full materials description.4 3/4 20 9.31 338 12.00 305 10.75 121 18.50 12.0 2 50 14.50 241 .75 19.9 8.88 200 7.00 229 7.4 8. NPS DN B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Valve flanges conform to ASME Standard B16.38 35.41 264 1.41 188 . Disc/Seat: HF 15493MB8 Trim: 316 Disc/Seat: HF Size 15493MBS Trim: Monel Seat: HF A-End-to-End 15493MB6 Trim: 13% Cr. 74 1/2 15 8.50 216 7.8 50.50 318 1.9 For Cv factors see page 123. 1-1/2 40 12.00 203 55.75 248 111.75 121 18. Blue numerals are in millimeters and kilograms.88 200 7. Flanged Ends 1/4" R.7 4.1 9.50 368 13. 112-115 SERIES NUMBER Threaded Socket Weld 15493 Trim: 13% Cr.6 1 25 10.F. Valve Matrix U. Disc/Seat: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Faced Seat ASME B16.0 25.6 8.5 and end-to-end dimensions conform to ASME Standard B16.00 178 37.34 MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Dimensions Bold face numerals are in inches and pounds.8 .2 16.97 279 10.5 BAR @ 38°C) ■ ■ ■ ■ ■ ■ ■ For other ratings see pgs.7 4.41 188 .12 257 9.10.1 7.00 254 10.50 12.Flow Control Division Vogt Valves Forged Globe Valves Class 1500 (PN 260) Conventional Port 3705 PSI @ 100°F (255.12 28. Valve Matrix U.) SW15141 Trim: 13% Cr.1 7. Blue numerals are in millimeters and kilograms.5 15.50 114 7.41 264 1.75 121 9.50 12.75 197 10.7 4.3 1-1/4 32 7.7 4.0 1-1/2 40 7.7 For Cv factors see page 123. 15501 GLOBE CLASS 1500 (PN 260) SERIES NUMBER Body/Bonnet A105 15141 15141FHF 15141F8M 15141MB8 15141MBS 15141MB6 15141MM F316/F316L SW15141MM Trim: Monel Seat: HF 3600 PSI @ 100°F (248.50 318 1.50 114 7.Flow Control Division Vogt Valves Forged Globe Valves Class 1500 (PN 260) Conventional Port ■ ■ ■ ■ ■ ■ ■ 3705 PSI @ 100°F (255.1 9.00 178 20. Cl.8 28.97 279 10.38 35.5 BAR @ 38°C) For other ratings see pgs.12 257 9.41 188 .75 19.00 229 13.2 16.00 203 34.3 1 25 6. 2 (1 1/4 Cr.25 159 10. Seat: HF SW15141FHF Trim: 13% Cr.4 3/4 20 4.41 264 1.75 121 9.41 188 . 2 50 9. Disc/Seat: HF Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.75 248 61. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter 3750 PSI @ 100°F (258.4 8.4 4.3 BAR @ 38°C) 15501 15501FHF F11.5 9.4 8.75 197 10.12 28.88 200 7.50 241 .97 279 10. 75 1/2 15 4. Disc/Seat: HF SW15141F8M Trim: 316 Seat: HF SW15141MB8 Trim: 316 Disc/Seat: HF SW15141MBS Trim: Monel Seat: HF SW15141MB6 Trim: 13% Cr.12 28. Disc/Seat: HF SW15501 Trim: 316 SW15501FHF Trim: 316 Disc/Seat: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Bold face numerals are in inches and pounds.6 BAR @ 38°C) 15351 SW15351 Trim: 13% Cr.8 4. 15351.00 203 35.34 Weight Refer to pages 116-120 for full materials description.88 200 7.1 .31 338 12.50 12. 112-115 15141. 62 15.2 4.31 338 12.5 BAR @ 38°C) For other ratings see pgs.47 190 .4 4.50 114 7. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Refer to pages 116-120 for full materials description.00 203 35.8 28.25 159 10.) No. Blue numerals are in millimeters and kilograms.9 3/4 20 4.8 1-1/2 40 7. Seat: HF Size 1/2 3/4 1 1-1/2 2 Cv Factor 1.54 11.00 178 21.75 248 62.38 4.2 9. 76 1/2 15 4.7 7.44 11.44 11.46 2. of Turns 3 4-1/2 5 5-1/4 6-1/2 Round Bolted Bonnet Spiral Wound Gasket Outside Screw & Yoke Bolted Gland Loose V-Port Disc Integral Hard Faced Seat Dial & Indicator ASME B16.94 23.Flow Control Division Vogt Valves Forged Globe Valves – For Flow Control Service Class 1500 (PN 260) ■ ■ ■ ■ ■ ■ ■ ■ Conventional Port 3705 PSI @ 100°F (255.9 8.5 16.00 (Approx. 112-115 15443 GLOBE CLASS 1500 (PN 260) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 15443 SW15443 Trim: 13% Cr.75 197 11.47 190 .5 .1 2 50 9.7 1 25 6.50 13.2 4.50 318 1.03 26.75 121 10.88 200 7.00 229 13.34 Bold face numerals are in inches and pounds.88 200 7.8 4.62 244 .00 279 10.12 257 9.34 263 .5 9.50 114 7.75 121 10. 77 1-1/2 40 7.8 2 50 9.7 12. Seat: HF 15821 GLOBE CLASS 1500 (PN 260) A105 Body/Bonnet 15821F8M SW15821F8M Trim: 316 Seat: HF 15821FHF SW15821FHF Trim: 13% Cr.Flow Control Division Vogt Valves Forged Globe Valves Class 1500 (PN 260) Conventional Port ■ ■ ■ ■ ■ ■ 3705 PSI @ 100°F (255.00 229 13.41 188 .2 1-1/4 32 7.8 1 25 6.0 11.1 9.41 264 1. 112-115 SERIES NUMBER Threaded Socket Weld 15821 SW15821 Trim: 13% Cr.12 282 10.50 12.00 203 26.75 121 8.12 282 10.00 203 26.12 28.50 318 1.1 For Cv factors see page 123.0 8.4 3.00 178 18.5 BAR @ 38°C) For other ratings see pgs.50 114 7.0 22.75 197 11.41 188 .75 121 8. Dimensions Size NPS DN A-End-to-End B-Open 15821MB6 SW15821MB6 Trim: 13CR Disc/Seat: HF C-Closed D-Seat Diameter E-Handwheel Diameter MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Welded Bonnet Outside Screw & Yoke Bolted Gland Loose Disc Integral Hard Faced Seat ASME B16.0 3/4 20 4. 1/2 15 4.88 200 7.1 7.50 114 7.8 4. Blue numerals are in millimeters and kilograms.34 Weight Refer to pages 116-120 for full materials description.38 35.12 257 9.7 4.2 .4 8.31 338 12.50 12.50 241 .75 19. Valve Matrix U.88 200 7.41 264 1. Disc/Seat: HF 15821MM SW15821MM Trim: Monel Seat: HF 15821MB8 SW15821MB8 Trim: 316 Disc/Seat: HF 15821MBS SW15821MBS Trim: Monel Seat: HF Bold face numerals are in inches and pounds.4 8.7 4.12 28.75 248 49.75 197 11.25 159 10. 53 38.2 1-1/2 40 7.00 102 9. *1-1/2" & 2" sizes have impactor handwheels. Disc/Seat: HF (Solid Stellite Disc) Welded Bonnet Outside Screw & Yoke Bolted Gland Loose Solid Stellite Disc Integral Hard Faced Seat ASME B16. Refer to pages 116-120 for full materials description.1 9.06 230 8.75 19.7 7.53 38. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 1/2 15 4.88 378 1.00 279 10.00 178 9.38 416 14. 3 (2-1/4% Cr.9 12.00 102 9.00* 305 40.06 230 8.0 4.56 217 .1 For Cv factors see page 123.50 12.56 217 . 112-115 ■ ■ ■ ■ ■ ■ Socket Weld SW1510 Trim: 13% Cr.50 12. 78 2 50 7.1 1 25 5.0 19.4 BAR @ 38°C) SERIES NUMBER Body/Bonnet Threaded A105 1510 1510. Blue numerals are in millimeters and kilograms.34 LTD Pressure Class Bold face numerals are in inches and pounds.) 1522 SW1522 Trim: 13% Cr. 1511.88 378 1.12 130 11. 1522 Y PATTERN GLOBE LTD CLASS 1690 (PN 290) For other ratings see pgs.38 416 14.50 190 16.75 248 18. 2 (1-1/4% Cr. Disc/Seat: HF (Solid Stellite Disc) F22 Cl.9 12.1 3/4 20 4.1 4.Flow Control Division Vogt Valves Forged "Y" Pattern Globe Valves Class 1690 (PN 290) Conventional Port 4225 PSI @ 100°F (291. Disc/Seat: HF (Solid Stellite Disc) F11 Cl.) 1511 SW1511 Trim: 13% Cr.5 .7 7. Valve Matrix X.50 190 16.28 261 .1 8.00* 305 42.00 178 9.8 18. 75 19. Blue numerals are in millimeters and kilograms.2 2 50 8.) 66793 SW66793 Trim: 13% Cr.7 7.50 216 16.53 38. 1/2 15 4.12 130 10.50 394 1. 2 (1-1/4% Cr.50 419 15.50 419 15.9 12. 66733. Disc/Seat: HF (Solid Stellite Disc) Welded Bonnet Outside Screw & Yoke Bolted Gland Loose Solid Stellite Disc Integral Hard Faced Seat ASME B16. Refer to pages 116-120 for full materials description.2 10.50 394 1.Flow Control Division Vogt Valves Forged Globe Valves Class 2500 (PN 420) Full Port ■ ■ ■ ■ ■ ■ 6250 PSI @ 100°F (431. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight *1-1/2" & 2" sizes have impactor handwheels.1 9.) 66733 SW66733 Trim: 13% Cr.94 278 10.25 261 . 3 (2-1/4% Cr. 79 1-1/2 40 8.1 9.00* 305 68.1 For Cv factors see page 123.25 261 .50 216 16.3 1 25 5.00* 305 68.53 38.0 BAR @ 38°C) SERIES NUMBER Body/Bonnet Threaded A105 66723 66723. 112-115 Socket Weld SW66723 Trim: 13% Cr.6 10. Valve Matrix Y. 66793 GLOBE LTD CLASS 2500 (PN 420) For other ratings see pgs.56 217 . Disc/Seat: HF (Solid Stellite Disc) F11 Cl.06 230 8.12 130 10.94 278 10.75 248 22. Disc/Seat: HF (Solid Stellite Disc) F22 Cl.00 102 9.50 12.0 4.00 178 9.34 LTD Pressure Class Bold face numerals are in inches and pounds.8 31.7 31.1 3/4 20 5.9 12.2 .75 19.75 248 22. 50 190 17.12 130 11. Refer to pages 116-120 for full materials description. Disc/Seat: HF (Solid Stellite Disc) F22 Cl. 112-115 SERIES NUMBER Body/Bonnet Threaded* Socket Weld* A105 R 1510 SWR 1510 Trim: 13% Cr.9 12. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight *1-1/2" & 2" sizes have impactor handwheels.97 279 .00* 305 42.75 248 19. 1/2 15 5.8 18.1 9.5 8. 2 (1-1/4% Cr. Disc/Seat: HF (Solid Stellite Disc) F11 Cl.9 3/4 20 5.50 419 1.75 19.0 19. Disc/Seat: HF (Solid Stellite Disc) Inline Repairable Screw Bonnet Outside Screw & Yoke Bolted Gland Loose Solid Stellite Disc Integral Hard Faced Seat ASME B16.Flow Control Division Vogt Valves Forged "Y" Pattern Repairable Globe Valves Class 1690 (PN 290) ■ ■ ■ ■ ■ ■ ■ Conventional Port SW: 4225PSI @ 100°F (291.97 279 . Blue numerals are in millimeters and kilograms.5 8.00* 305 40.50 190 17.60 295 10.) R 1522 SWR 1522 Trim: 13% Cr. R 1522 Y PATTERN GLOBE LTD CLASS 1690 (PN 290) For other ratings see pgs.1 9.12 130 11.75 248 19.12 130 11.50 419 1. 80 1-1/2 40 7.75 248 19.1 2 50 7.75 19.97 279 .4 BAR @ 38°C) R 1510.53 38.75 19.60 295 10.9 12. R 1511.60 295 10.53 38.9 1 25 5.1 9. 3 (2-1/4% Cr.75 451 16.5 .9 For Cv factors see page 123. Valve Matrix Z-R.6 8.) R 1511 SWR 1511 Trim: 13% Cr.34 LTD Pressure Class Bold face numerals are in inches and pounds.75 451 16. 7 7.6 For Cv factors see page 123. 2 (1-1/4% Cr. Welded Bonnet Outside Screw & Yoke Bolted Gland Loose Solid Stellite Disc Integral Hard Faced Seat ASME B16.1 29.0 28.00 279 10.25 210 16.28 261 .53 38. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight *1-1/2" & 2" sizes have impactor handwheels.56 217 .12 130 11.1 BAR @ 38°C) THD: 6250 PSI @ 100°F (431.28 261 . 81 1-1/2 40 8. 2511.1 3/4 20 5. Valve Matrix Z.1 9.6 2 50 8.06 230 8. Disc/Seat: HF (Solid Stellite Disc) Threaded valves limited to Class 2500 Applications under ASME B16.25 210 16.75 248 19.94 430 15.) 2522 SW2522 Trim: 13% Cr.1 9. Refer to pages 116-120 for full materials description.9 12.Flow Control Division Vogt Valves Forged "Y" Pattern Globe Valves Class 2680 (PN 460) Full Port SW: 6700 PSI @ 100°F (462.94 430 15.0 BAR @ 38°C)* ■ ■ ■ ■ ■ ■ 2510. Disc/Seat: HF (Solid Stellite Disc) F22 Cl. Blue numerals are in millimeters and kilograms.53 38.56 395 1. 112-115 SERIES NUMBER Body/Bonnet Threaded* Socket Weld A105 2510 SW2510 Trim: 13% Cr. 3 (2-1/4% Cr. 2522 Y PATTERN GLOBE LTD CLASS 2680 (PN 460) For other ratings see pgs.00* 305 65.75 248 19.56 395 1.1 .00* 305 62.75 19.0 8.) 2511 SW2511 Trim: 13% Cr.1 4.12 130 11.6 1 25 5.75 19.50 12.34. 1/2 15 4.00 102 9.34 LTD Pressure Class Bold face numerals are in inches and pounds.9 12. pages 112-115.0 8.00 178 9. See 2500 LTD Class Press/Temp tables.00 279 10. Disc/Seat: HF (Solid Stellite Disc) F11 Cl. 60 295 10.75 248 19.75 19.75 19.5 8.60 295 10. 2 (1-1/4% Cr.6 8. Disc/Seat: HF (Solid Stellite Disc) F22.9 1 25 5. R 2522 Y PATTERN GLOBE LTD CLASS 2680 (PN 460) For other ratings see pgs.75 248 19.) R 2522 SWR 2522 Trim: 13% Cr.50 419 1.12 130 11.5 28.1 9. Refer to pages 116-120 for full materials description.4 2 50 8.0 BAR @ 38°C) ■ ■ ■ ■ ■ ■ ■ R 2510.1 BAR @ 38°C) THD: 6250 PSI @ 100°F (431.75 19.88 454 16. 3 (2-1/4% Cr. Blue numerals are in millimeters and kilograms.12 130 11.1 9.97 279 .) R 2511 SWR 2511 Trim: 13% Cr.75 248 19.Flow Control Division Vogt Valves Forged "Y" Pattern Repairable Globe Valves Class 2680 (PN 460) Full Port SW: 6700 PSI @ 100°F (462. See 2500 LTD Class Press/Temp tables. 82 1-1/2 40 8.53 38.34. Disc/Seat: HF (Solid Stellite Disc) F11.1 9. Inline Repairable Screw Bonnet Outside Screw & Yoke Bolted Gland Loose Solid Stellite Disc Integral Hard Faced Seat ASME B16. Cl.25 208 17. Valve Matrix Z-R.00* 305 62.00* 305 62.53 38.6 28. R 2511.34 LTD Pressure Class Bold face numerals are in inches and pounds. Disc/Seat: HF (Solid Stellite Disc) Threaded valves limited to Class 2500 Applications under ASME B16.97 279 .60 295 10.5 8.9 12. 112-115 SERIES NUMBER Body/Bonnet Threaded* Socket Weld* A105 R 2510 SWR 2510 Trim: 13% Cr.9 For Cv factors see page 123.88 454 16.50 419 1. pages 112 -115. Cl.97 279 .12 130 11. 1/2 15 5.25 208 17.9 3/4 20 5.4 .9 12. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight *1-1/2" & 2" sizes have impactor handwheels. 25 6. Valve Matrix AA.25 210 11.19 30.12 79 6.4 19.06 205 7.00 102 5.06 154 5.50 190 7.69 221 .5 1/2 15 3.8 For Cv factors see page 123.9 19.8 4.00 102 8.7 4.75 121 8.72 18.5 3/8 10 3.06 10.56 14.9 4.2 8.6 9.0 1 25 5.56 14.9 9.81 249 1.8 13.56 192 .00 203 28.50 12.12 79 6. 1/2 15 3.7 3.9 3.12 257 1.00 8.50 292 1.50 165 .0 5.81 1.3 3/4 20 4.75 146 13.2 1.88 149 .4 3.81 173 6.25 83 3.3 20.25 159 10. Dimensions Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight Series 1331T Series 1871T NPS DN 1/4 8 3.1 2.00 102 7.00 178 20.06 1.38 162 .2 4.75 214 230 273 7.25 83 3.12 282 10.5 .12 79 6.7 3.06 256 9.88 149 .44 9.5 5.Flow Control Division Vogt Valves Forged Globe Valves – For Air.2 4.28 20.00 146 178 203 12.50 12.38 86 6. 1331T✯+ SW1331T✯+ Trim: A105 Plug Stem✯ Not recommended for steam or dry gas service.00 127 9.7 9. Refer to pages 116-120 for full materials description.9 32.9 BAR @ 38°C) NON-SHOCK PRESSURE TEMPERATURE NOT TO EXCEED 450°F 1331T.75 171 10.25 83 3.25 159 5.3 5.2 1.44 240 .6 7. Blue numerals are in millimeters and kilograms.25 159 5. Bold face numerals are in inches and pounds.44 36.39 9.2 1.53 38.9 3.5 3/8 10 3.12 79 6.69 197 216 246 .88 175 6. 1871T GLOBE TYPE 3000 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 1871T+ SW1871T+ Plug Type Disc Trim: 13% Cr.75 248 42.38 86 6.6 10.4 1-1/2 40 6.50 9.75 248 44. Water & Oil Service ■ ■ ■ ■ Screw Bonnet Flat Gasket Inside Screw Stem Loose Plug Type Disc or Plug Stem✯ ■ Renewable Seat or Integral Seat✯ Type 3000 Conventional Port 3000 PSI @ 100°F (206.25 83 3.6 26.0 2. Not recommended for steam service.38 264 9.39 9.3 3/4 20 4.25 210 12.5 + Valves contain TEFLON—maximum temperature 450°F.6 8.50 140 .75 121 8.39 9.12 232 8.50 140 .8 2 50 8.75 7.75 127 159 171 8. 83 1 1-1/4 1-1/2 25 32 40 5.00 6.9 1-1/4 32 6.1 1/4 8 3.00 102 5.2 1.00 178 .06 154 5.97 24.50 12.1 2 50 8.0 23.75 8.8 5.25 311 11. 6 1 25 2.50 12.0 3.6 9.50 216 7.1 3/4 20 2.22 158 5.0 .2 8.4 2 50 4.88 149 .75 146 11.22 234 8.53 217 .75 248 1. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight +Valves contain TEFLON—maximum temperature 450°F.12 257 9.75 248 35.75 121 8.3 5.19 30.00 178 16.50 12.38 86 10.97 202 . Blue numerals are in millimeters and kilograms.4 5.0 11. Not recommended for steam service.00 203 25.6 7.06 179 .5 7.50 64 8.19 56 7.Flow Control Division Vogt Valves Forged Angle Valves – For Air.88 48 6.9 BAR @ 38°C) NON-SHOCK PRESSURE TEMPERATURE NOT TO EXCEED 450°F 2891T ANGLE GLOBE TYPE 3000 A105 Body/Bonnet Screw Bonnet Flat Gasket Joint Inside Screw Stem Screw Gland Loose Plug Type Disc Renewable Seat SERIES NUMBER Threaded Socket Weld 2891T+ SW2891T+ Trim: 13% Cr.44 240 1.7 4.44 36.2 16. Bold face numerals are in inches and pounds.2 For Cv factors see page 123. Water & Oil Service Type 3000 ■ ■ ■ ■ ■ ■ Conventional Port 3000 PSI @ 100°F (206. 84 1-1/4 32 3.72 18.00 76 9.50 267 9. 1/2 15 1.7 2.5 1-1/2 40 3.97 24.56 192 7.7 4.00 102 4.12 105 10. Refer to pages 116-120 for full materials description. Valve Matrix BB. 97 124 . Refer to pages 116-120 for full materials description.75 197 7.00 102 7.7 1 25 4.3 For Cv factors see page 123.80 1/2 15 2. Blue numerals are in millimeters and kilograms.9 3.97 124 .Flow Control Division Vogt Valves Forged Globe Valves – For Meter & Gauge Line Service ■ ■ ■ ■ ■ ■ Type 4000 Conventional Port 4000 PSI @ 100°F (275.38 9. 1/4 8 2. Not recommended for steam or dry gas service.9 3.25 83 2.00 127 .62 15.31 7.75 70 5.31 7.34 136 4.25 83 1. 85 3/4 20 3.90 3/8 10 2.9 2. Valve Matrix CC.7 3.38 137 5.75 70 5.7 4. Dimensions NPS DN Size A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight +Valves contain TEFLON—maximum temperature 450°F.34 136 4.9 1.38 86 6.75 121 8.25 159 .75 70 5.0 .50 12.00 178 .88 175 6.7 4.25 83 2. Bold face numerals are in inches and pounds.00 102 5.8 .0 .9 BAR @ 38°C) NON-SHOCK PRESSURE TEMPERATURE NOT TO EXCEED 450°F Union Bonnet Flat Gasket Joint Inside Screw Stem Screw Gland Needle Point Control MSS-SP-99 58431T GLOBE TYPE 4000 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 58431T+ SW58431T+ Trim: 13% Cr.8 4. 81 249 8.25 83 2.0 5.25 83 1.69 43 6. Refer to pages 116-120 for full materials description.38 35 5.31 7.2 6. 9841T.00 127 .72 1/2 15 1.00 229 8.75 121 6.00 178 .75 121 7.75 70 5.7 4.8 8.25 159 .31 7.00 127 . Dimensions Needle Point Port SERIES NUMBER Threaded Socket Weld 9841T+ SW9841T+ Trim: 13% Cr.8 BAR @ 38°C) Temperature not to exceed 450°F SERIES NUMBER Threaded Socket Weld 9871T+ SW9871T+ Trim: 13% Cr.00 178 19.4 7.00 102 4.97 126 .7 2.9 3.9 4.7 4. Bold face numerals are in inches and pounds.31 135 4.9 3/8 10 2.31 135 4.7 4.00 25.00 51 7.50 12.7 3.75 19.8 .6 13 For Cv factors see Page 123.00 102 5.6 3.25 83 1.25 159 .9 3.75 197 7.97 126 .6 .9 3.3 3.00 203 28.00 102 7. Blue numerals are in millimeters and kilograms. Angle Valve A105 Body/Bonnet Bold face numerals are in inches and pounds.25 134 5.1 .97 126 . NPS DN Size Body/Bonnet A105 F316/F316L B-Open C-Closed ■ ■ ■ ■ ■ ■ Screw Bonnet Flat Gasket Joint Inside Screw Stem Screw Gland Needle Point Control MSS-SP-99* D-Seat Diameter E-Handwheel Diameter Weight 1/2 15 2. Not recommended for steam or dry gas service.38 9.8 3.82 *MSS-SP-99 not applicable for Sizes 1-1/4.12 282 10. Not recommended for steam or dry gas service. 1-1/2 and 2.38 9.25 83 1.31 135 4.75 197 11.0 2.75 172 6.25 134 5.1 1 25 2.5 1.8 .31 7.2 Size ■ ■ ■ ■ ■ ■ Screw Bonnet Flat Gasket Joint Inside Screw Stem Screw Gland Needle Point Control MSS-SP-99 NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight 86 1 25 4.62 15.75 171 6.31 7.62 15.75 70 5.50 12.75 121 9.1) Trim: 13% Cr.6 2 50 7.25 31. Valve Matrix CC.82 3/8 10 1.06 256 1.0 8.72 3/4 20 3.25 159 9. 3/4 20 1. 1/4 8 2.19 208 .25 83 2. Valve Matrix BB.31 135 4.4 1-1/4 40 4.00 178 . For Cv factors see Page 123.0 1-1/2 40 6.38 86 6.75 146 13.38 35 5.6 1.75 70 5.1 +Valves contain TEFLON—maximum temperature 450°F. 9821T.6 .25 83 1.Flow Control Division Vogt Valves Forged Globe & Angle Valves – For Meter & Gauge Line Service Type 5000 Conventional Port 5000 PSI @ 100°F (344.94 227 1.9 3.38 35 5. Dimensions 1/4 8 1.97 126 . 9871T GLOBE & ANGLE TYPE 5000 9821T+ A-End-to-End SW9821T+ (Sizes 1/4 .75 197 7. Blue numerals are in millimeters and kilograms. 8 BAR @ 38°C) NON-SHOCK PRESSURE TEMPERATURE NOT TO EXCEED 450°F Screw Bonnet Flat Gasket Joint Inside Screw Stem Screw Gland Loose Plug Type Disc Renewable Seat 3991T GLOBE TYPE 6000 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 3991T+ SW3991T+ Trim: 13% Cr.00 305 65.0 1.19 310 1.50 216 12.00 102 8.7 2 50 8.81 325 12.44 265 .Flow Control Division Vogt Valves Forged Globe Valves – For Air.39 9. 1/2 15 4.00 279 10.75 248 47. 87 1-1/2 40 8.9 3/4 20 5.25 210 .94 329 12.2 9.7 1 25 6. Blue numerals are in millimeters and kilograms.62 194 .19 30.75 171 11.50 12.75 146 12.00 305 1.2 9.00 127 8.7 29.6 12. Not recommended for steam service.6 1-1/4 32 6.6 5.72 18.31 236 . Water & Oil Service Type 6000 Full Port ■ ■ ■ ■ ■ ■ 6000 PSI @ 100°F (413.00 203 31.69 221 8.44 36.88 251 9. Valve Matrix AA. Refer to pages 116-120 for full materials description.1 14.9 4.25 159 9.9 21.8 .7 5.00 203 7.97 24.00 178 21.1 For Cv factors see page 123. Dimensions Size NPS DN A-End-to-End B-Open C-Closed D-Seat Diameter E-Handwheel Diameter Weight + Valves contain TEFLON—maximum temperature 450°F.75 121 9.3 7.25 210 12. Bold face numerals are in inches and pounds.6 8. as applicable. Auxiliary Operators for Vogt valves are normally custom mounted in our plant where limit and torque switches.Flow Control Division Auxiliary Operators Vogt Valves The superstructures of Vogt valves are FORGED RUGGED and lend themselves to the adaptation of Auxiliary Operators. MOTOR OPERATED VALVE BEVEL GEAR OPERATED VALVE 88 DIAPHRAGM OPERATED VALVE . can be set and valves tested to users specifications. Any of the three types illustrated can generally be furnished and requests for quotations are invited. on the order. union. to provide a minimum of 2 psi pressure drop for ball and Leakage rate for Vogt check valves with metal-to-metal piston type valves and 1/2 psi for swing check type seats are dependent on the amount of back pressure valves. Dimensions are subject to change without notice. and bonnetless type check valves are manufactured to meet a wide variety of service applications. A spring can be added to piston check valves not currently equipped with that option if specified Vogt check valves (non spring loaded) should be sized Check valves are designed to prevent reverse flow. See Page 100 for 89 . Piston. or anticipated. should not be used in gas or low back pressure liquid Vogt’s “Y” pattern check valves complement our “Y” pattern and InLine repairable globe valve lines used in refineries. This will assure that the valves will not be subject and the viscosity of the flowing medium. which a history of noisy check valve operation has Dimensions are in inches and millimeters. swing and spring controlled check valve designs for horizontal or vertical (upward) flow applications for the most often specified pressure classes are BOLTED BONNET PISTON CHECK VALVE NO BONNET SWING CHECK VALVE BOLTED BONNET BALL CHECK VALVE available. preference for reciprocating compressor service in Piston and ball check valves should not be used in applications where Vogt zero leakage check valves. seal weld. ball. chemicals. Swing check valves are more tolerant for applications of this nature. applications if zero leakage is desired. power Spring loaded piston check valves are the Vogt and related industries. been experienced. socket weld or flanged ends. including bolted.Flow Control Division Vogt Valves Check Valve Section – Pages 89-111 Vogt check valves are forged from fine grain steel and are available with threaded. Most bonnet designs. rusting or rust particles are present Order by Size and Series Number. Check valves to noisy operation and premature wear of parts. 12 4. .50 .0 For Cv factors see page 123.Flow Control Division Vogt Valves Forged Check Valves Class 150 (PN 20) Conventional Port ■ ■ ■ ■ ■ ■ 285 PSI @ 100°F (19.00 108 117 127 165 203 2.5 38.F.62 5.6 9.4 15.3 6.50 8.5 10. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Valve flanges conform to ASME Standard B16.00 89 99 108 127 152 . Seat: HF 573MB8 573.25 4.28 1. Blue numerals are in millimeters and kilograms.4 3. Flanged Ends 1/16" R.25 5.0 4.1 32. 90 NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 4.9 5.50 4.50 3. Valve Matrix FF.7 12.94 65 65 79 114 125 3.7 BAR @ 38°C) For other ratings see pgs.34 573MBS Trim: Monel Seat: HF A350 LF2 573MM Trim: Monel Seat: HF 573F8M Trim: 316 Seat: HF 32573 Trim: 13% Cr.56 2.1 20.00 6.10.7 33. 32573 CHECK CLASS 150 (PN 20) Body/Bonnet A105 Trim: 316 SS Disc/Seat: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16. 112-115 SERIES NUMBER 573 Trim: 13% Cr. Seat: HF Meets API-602 required wall thicknesses.5 and end-to-end dimensions conform to ASME Standard B16.53 12.50 .00 6.56 3. Refer to pages 116-120 for full materials description.88 4. Bold face numerals are in inches and pounds.75 1.1 2.5 19. 62 4. 112-115 583. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Valve flanges conform to ASME Standard B16.56 2. Valve Matrix FF.0 4.53 12. Seat: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Meets API-602 required wall thicknesses.0 13.9 38. Seat: HF 583MB8 Trim: 316 SS Disc/Seat: HF 583MBS Trim: Monel Seat: HF Trim: Monel Seat: HF 583MM A350 LF2 583F8M Trim: 316 Seat: HF 32583 Trim: 13% Cr.50 . 91 NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 6.7 27.50 4.3 For Cv factors see page 123.94 65 65 79 114 125 3.50 152 178 203 229 267 2.75 1.28 1. 32583 CHECK CLASS 300 (PN 50) Body/Bonnet SERIES NUMBER A105 583 Trim: 13% Cr.7 12.50 . Refer to pages 116-120 for full materials description.7 17.2 12.00 9.88 6.9 6.00 10.10.1 32.12 4.00 8.12 6.F.75 4.34 Flanged Ends 1/16" R.56 3. Blue numerals are in millimeters and kilograms. Bold face numerals are in inches and pounds. Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16. .0 BAR @ 38°C) ■ ■ ■ ■ ■ ■ For other ratings see pgs.0 3.Flow Control Division Vogt Valves Forged Check Valves Class 300 (PN 50) Conventional Port 740 PSI @ 100°F (51.7 19.50 95 117 124 155 165 .5 6.5 and end-to-end dimensions conform to ASME Standard B16.6 10.5 38.00 7. 53 12.50 4. 92 For Cv factors see page 123.12 6.9 9.34 Flanged Ends 1/4" R. . Blue numerals are in millimeters and kilograms.75 1.9 6. Valve Matrix FF.0 A-End-to-End B C D-Seat Diameter Weight Valve flanges conform to ASME Standard B16.62 4.2 19.F.7 12.28 1.8 3.75 4.56 2.2 41.5 38.56 3.10.2 31.50 8.9 14. Bold face numerals are in inches and pounds.50 95 117 124 155 165 .8 15. 32593 CHECK CLASS 600 (PN 110) Body/Bonnet A105 A350 LF2 SERIES NUMBER 593 Trim: 13% Cr. Seat: HF MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16.7 19. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 6.50 .94 65 65 79 114 125 3. 112-115 593. Dimensions Size Meets API-602 required wall thicknesses. Refer to pages 116-120 for full materials description. Seat: HF 593MB8 Trim: 316 SS Disc/Seat: HF 593MBS Trim: Monel Seat: HF 593MM Trim: Monel Seat: HF 593F8M Trim: 316 Seat: HF 32593 Trim: 13% Cr.50 9.1 BAR @ 38°C) For other ratings see pgs.50 .88 6.1 4.1 32.50 11.4 6.Flow Control Division Vogt Valves Forged Check Valves ■ ■ ■ ■ ■ ■ Class 600 (PN 110) Conventional Port 1480 PSI @ 100°F (102.12 4.5 and end-to-end dimensions conform to ASME Standard B16.50 7.50 165 190 216 241 292 2. Flow Control Division Vogt Valves Forged Check Valves – For HF Alkylation Service Class 800 (PN 130) 1975 PSI @ 100°F (136.2 BAR @ 38°C) ■ ■ ■ ■ ■ ■ For other ratings see pgs. 112-115 SERIES NUMBER Threaded Socket Weld – SWB43721HF2 Sizes 1/2-1” Trim: Monel B 43721 CHECK CLASS 800 (PN 130) A105 Body/Bonnet – – SWB43721HF4 Trim: Monel Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Ball Check Removable Seat ASME B16.34 HYDROFLURIC ACID (HF) ALKYLATION VALVES. UOP APPROVED. SWB43721HF5 Trim: Monel Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 4.00 4.62 6.25 7.75 9.00 102 117 159 197 229 1.12 1.56 2.25 2.69 3.50 28 40 57 68 89 2.56 3.06 4.50 4.88 5.94 65 78 114 124 151 .39 .59 .97 1.44 1.88 9.9 15.0 24.6 36.6 47.8 3.5 6.5 17.5 25.8 47.4 1.6 3.0 8.0 11.7 21.5 For Cv factors see page 123, Valve Matrix HH. 93 Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.2 BAR @ 38°C) ■ ■ ■ ■ ■ ■ For other ratings see pgs. 112-115 SERIES NUMBER Threaded Socket Weld 4835 SW4835 Trim: 13% Cr. 4835 SWING CHECK CLASS 800 (PN 130) A105 Body/Bonnet Round Bolted Bonnet Flat Gasket Joint Horizontal or Vertical Upward Flow Swing Check Renewable Seat ASME B16.34 Meets API-600 required wall thicknesses. Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Dimensions Size NPS 1/2 3/4 1 1-1/4 1-1/2 2 DN 15 20 25 32 40 50 4.00 4.00 5.00 6.50 6.50 7.25 102 102 127 165 165 184 1.31 1.31 1.75 2.19 2.19 2.62 33 33 44 56 56 66 4.62 4.62 5.50 6.38 6.38 6.94 117 117 140 162 162 176 .39 .39 .69 .97 1.19 1.44 9.9 9.9 17.5 24.6 30.2 36.6 13.2 13.0 22.1 29.1 30.2 39.9 6.0 6.0 10.0 13.2 13.7 18.1 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description. For Cv factors see page 123, Valve Matrix JJ. 94 Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.2 BAR @ 38°C) For other ratings see pgs. 112-115 S 701, S 718 CHECK CLASS 800 (PN 130) A105 Body/Bonnet ■ ■ ■ ■ ■ ■ SERIES NUMBER Threaded Socket Weld S701 SWS701 Trim: 13% Cr. Seat: HF Round Bolted Bonnet Spiral Wound Gasket Horizontal or Vertical Upward Flow Swing Check Hard Faced Seat ASME B16.34 F316, F316L Body/Bonnet 1920 PSI @ 100°F (132.4 BAR @ 38°C) S718 SWS718 Trim: 316 Seat: HF Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 3.38 3.38 4.19 5.44 5.94 86 86 106 138 151 .78 .78 .97 1.28 1.56 20 20 25 33 40 2.33 2.33 3.06 4.46 4.92 59 59 78 113 125 .50 .50 .75 1.25 1.50 12.7 12.7 19.1 31.8 38.1 3.9 3.8 6.1 16.5 25.3 1.8 1.7 2.7 7.5 11.5 For Cv factors see page 123, Valve Matrix MM. 95 8 4. Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.2 2.1 31.1 4.1 For Cv factors see page 123.8 38.00 6.34 Bold face numerals are in inches and pounds. Seat: HF S 673 CHECK CLASS 150 (PN 20) A105 Body/Bonnet Dimensions Flanged Ends 1/16" R.7 BAR @ 38°C) For other ratings see pgs. 95A .F.62 5.43 4.06 4.33 3.75 1.25 5.1 8.Flow Control Division Vogt Valves Forged Check Valves Class 150 (PN 20) Conventional Port 285 PSI @ 100°F (19. Round Bolted Bonnet Spiral Wound Gasket Horizontal or Vertical Upward Flow Swing Check Hard Faced Seat ASME B16.8 6.7 19.1 18.50 .8 33.2 9. Blue numerals are in millimeters and kilograms.50 8.25 4.00 89 99 108 127 152 .89 59 59 78 112 124 3. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 4.33 2.5 15.50 12. 112-115 S673 ■ ■ ■ ■ ■ ■ SERIES NUMBER Trim: 13% Cr.7 12.88 4.00 108 117 127 165 203 2. Valve Matrix MM.50 .25 1.2 2.50 3.00 6. 9 4.50 .50 95 121 127 155 165 .50 140 152 216 241 267 2.50 6.Flow Control Division Vogt Valves Forged Check Valves Class 300 (PN 50) Conventional Port 740 PSI @ 100°F (51.89 59 59 78 112 124 3. Blue numerals are in millimeters and kilograms.1 6. Bold face numerals are in inches and pounds.34 Flanged Ends 1/16" R.9 For Cv factors see page 123.12 6. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.0 BAR @ 38°C) For other ratings see pgs.50 9.50 12.00 8.9 2.33 2.3 11.3 13.1 31.50 10.7 19.8 38. 95B .75 4. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 5. Seat: HF S 683 CHECK CLASS 300 (PN 50) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Horizontal or Vertical Upward Flow Swing Check Hard Faced Seat ASME B16.3 9.25 1.75 1.75 5.7 12.43 4.8 17.F.50 . 112-115 ■ ■ ■ ■ ■ ■ S683 SERIES NUMBER Trim: 13% Cr.33 3.00 6. Valve Matrix MM.06 4.4 2.2 6.60 39. 112-115 ■ ■ ■ ■ ■ ■ S693 SERIES NUMBER Trim: 13% Cr. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.50 7.50 8.8 43.25 1.33 2. Valve Matrix MM.F.50 12.Flow Control Division Vogt Valves Forged Check Valves Class 600 (PN 110) Conventional Port 1480 PSI @ 100°F (102.34 Flanged Ends 1/4" R.12 6.00 6.5 12.33 3.62 5.50 95 117 127 155 165 . Bold face numerals are in inches and pounds.75 1.9 10.1 BAR @ 38°C) For other ratings see pgs.75 4.1 4.6 19.8 38.50 . 95C .50 165 190 216 241 292 2.50 11.89 59 59 78 112 124 3. Blue numerals are in millimeters and kilograms.7 19.43 4.2 3.50 .7 12.6 For Cv factors see page 123.2 14. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 6.1 6.50 9. Seat: HF S 693 CHECK CLASS 600 (PN 110) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Horizontal or Vertical Upward Flow Swing Check Hard Faced Seat ASME B16.06 4.1 31.4 27.6 6. Valve Matrix MM.Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.34 S 74 SWING CHECK CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld S74 SWS74 Trim: 13% Cr.50 12.7 1.50 3.50 3.50 .6 5. 112-115 ■ ■ ■ ■ No Bonnet Horizontal or Vertical Upward Flow Swing Type Check Welded Seat Insert with Integral Stainless Seat Deposit ■ ASME B16.75 1.1 3.7 19.38 44 44 51 64 86 .6 2.1 10.2 BAR @ 38°C) For other ratings see pgs.75 1.50 .75 2. NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 3.00 6.75 89 89 102 127 171 1.00 5.3 4.9 10.7 3.5 1.7 23.50 4.8 For Cv factors see page 123.1 31. Dimensions Size A-End-to-End B C-Seat Diameter Weight Refer to pages 116-120 for full materials description. Blue numerals are in millimeters and kilograms.7 12.8 38.00 2.25 1. with Type 309 Integral Seat Bold face numerals are in inches and pounds. 96 . B 718 CHECK CLASS 800 (PN 130) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld B701 SWB701 Trim: 18% Cr. Seat: HF 316/316L Body/Bonnet 1920 PSI @ 100°F (132. Valve Matrix FF.25 6.7 12.75 95 102 117 159 159 197 1.Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.56 2.56 3. 97 .5 2.34 SWB701HF6 Sizes 1/2-2 (No 1-1/4) SWB701HF7 Sizes 1/2-2 (No 1-1/4) Trim: 18% Cr.56 2. Seat: HF – – HYDROFLUORIC ACID (HF ALKYLATION VALVES.0 26. Blue numerals are in millimeters and kilograms.50 .28 1.00 1.8 8.12 1. For Cv factors see page 123.1 1.50 4. Dimensions Size NPS 1/2 3/4 1 1-1/4 1-1/2 2 DN 15 20 25 32 40 50 3.75 4.50 .7 19.69 25 28 40 57 57 68 2.5 32.50 4.9 3.5 6.25 2.28 1.75 1.5 1.2 BAR @ 38°C) ■ ■ ■ ■ ■ ■ For other ratings see pgs.00 4.5 38.2 17.8 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.25 7.7 11. Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Ball Check Integral Seat ASME B16.25 2. 112-115 B 701.6 17.4 BAR @ 38°C) B718 SWB718 Trim: 316 Bold face numerals are in inches and pounds. UOP APPROVED.4 3.1 32.53 12.0 7.94 65 65 78 114 114 125 .06 4.62 6. 75 197 2.25 159 2. 112-115 CHECK CLASS 800 (PN 130) Bold face numerals are in inches and pounds.2 BAR @ 38°C) NPS DN Size 710 For other ratings see pgs.94 126 1.1 2.00 102 1.06 78 .75 95 1.7 3.50 114 1.4 Round Bolted Bonnet Spiral Wound Gasket Horizontal or Vertical Upward Flow Spring Control Piston Check or Ball Check Integral Hard Faced Seat ASME B16.2 1.50 12. (302 Spring) Disc/Seat: HF B-Center-to-Bottom C-Center-to-Top D-Seat Diameter Weight ■ ■ ■ ■ ■ ■ ■ 1/4 8 3.69 68 4.0 7.5 2 50 7.28 32.25 159 2.8 1-1/4 32 6.0 11.4 1.75 197 2.8 1-1/2 40 6.5 3/4 20 4.75 19.12 28 2.5 7.1 2.75 95 1.5 1 25 4.5 Refer to pages 116-120 for full materials description.50 12.56 40 3.25 57 4.00 102 1. (302 Spring) Seat: HF NPS DN A-End-to-End B-Center-to-Bottom C-Center-to-Top D-Seat Diameter Weight 1/2 15 3. Blue numerals are in millimeters and kilograms.7 3.62 117 1.75 19.5 16. (302 Spring) Seat: HF 710FHF SW710FHF Trim: 13% Cr.50 12.7 3.1 6.50 12.5 16.62 117 1.69 68 4.0 11.56 65 .1 6.28 32.94 126 1.25 57 4.50 12.56 40 3.5 3/4 20 4.06 78 . 98 1 25 4.56 65 .56 65 .56 65 .34 Bold face numerals are in inches and pounds.75 95 1.4 .56 65 .75 95 1.4 1.5 7.53 38.25 159 2.7 3.5 1/2 15 3.00 25 2.56 65 .7 3.Flow Control Division Vogt Valves Forged Check Valves – Spring Control Class 800 (PN 130) Conventional Port 1975 PSI @ 100°F (136.5 3/8 10 3.00 25 2.7 1-1/2 40 6.9 25.28 32.50 114 1. Blue numerals are in millimeters and kilograms.9 25.50 114 1.00 25 2.12 28 2.5 2 50 7. Dimensions A105 Body/Bonnet A-End-to-End SERIES NUMBER Threaded Socket Weld 710 SW 710 Trim: 13% Cr.00 25 2.2 1. Dimensions A105 Body/Bonnet Size SERIES NUMBER Threaded Socket Weld B 710 SWB 710 Trim: 18% Cr.4 1.50 12.53 38.5 17.7 3.25 57 4.4 1. 56 3. Blue numerals are in millimeters and kilograms.5 1.50 4.7 12.7 12.4 A-End-to-End B C D-Seat Diameter Weight See next page for assistance in selecting the type of "ZL" Ring to use.56 2.00 1.28 1. 82718 CHECK CLASS 800 (PN 130) For other ratings see pgs.25 7.25 2.Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Conventional Port 32701.7 12.53 12.75 1.28 1.7 19.00 1.5 2.5 1.5 1.69 25 25 25 28 40 57 57 68 2.06 4.62 6.9 3. Valve Matrix FF.1 17.50 .4 6.34 NPS 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 DN 8 10 15 20 25 32 40 50 3.75 95 95 95 102 117 159 159 197 1.25 2.12 1.0 1.4 3.7 7.50 .5 25.56 2.56 2. 99 For Cv factors see page 123.25 6. Dimensions Size Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16. .4 3.2 BAR @ 38°C) SERIES NUMBER MATERIALS MEET Threaded Socket Weld REQUIREMENTS OF 32701 SW32701 NACE STANDARD Trim: 13% Cr.2 3. + Valves contain TEFLON — maximum temperature 500°F.0 16.75 3.5 11. 718.94 65 65 65 65 78 114 114 125 .00 4. Refer to pages 116-120 for full materials description.50 .8 7.75 4.1 32. 112-115 A350 LF2 Body/Bonnet 1975 PSI @ 100°F (136.56 2.50 .75 3.50 4. MR-01-75 FOR Seat: HF SOUR SERVICE 32701MB8 ■ ■ ■ ■ ■ ■ SW32701MB8 Trim: 316SS Disc/Seat: HF F316/F316L Body/Bonnet 1920 PSI @ 100°F (132.4 BAR @ 38°C) Threaded Socket Weld 82718 SW82718 Trim: 316H Bold face numerals are in inches and pounds.00 1.5 32.4 BAR @ 38°C) Threaded Socket Weld 718 SW718 Sizes 1/2-2 (no 1 1/4) 718T+ SW718T+ Trim: 316 F316H Body/Bonnet 1920 PSI @ 100°F (132.5 38. 75 4.1 17.5 11.4 3.25 2.06 4. 112-115 SERIES NUMBER Threaded Socket Weld 701 SW701 Trim: 13% Cr.25 7.00 4.56 2.7 7.2 3.50 4.75 3.5 1.4 3.25 6.5 1.94 65 65 65 65 78 114 114 125 . 100 For Cv factors see page 123.56 2.12 1.62 6.25 2. NPS 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 DN 8 10 15 20 25 32 40 50 3.56 3.8 7.5 2.4 A-End-to-End ZERO LEAKAGE "ZL" (RING) 701ZLB Buna N -20°F to 250°F 701ZLE -20°F to 300°F MATERIALS MEET REQUIREMENTS OF NACE STANDARD MR-01-75 FOR SOUR SERVICE Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16.5 1.00 1.34 B C Trim: 13% Cr Seat: HF D-Seat Diameter Weight See preceding page for assistance in selecting the type of "ZL" Ring to use.0 1.2 BAR @ 38°C) Ethylene Propylene 701ZLN -20°F to 240°F Neoprene 701ZLV -20°F to 400°F Viton } Soft Insert "ZL" Ring Zero Leakage Dimensions Size Bold face numerals are in inches and pounds.1 32.00 1.7 12.5 38. Valve Matrix FF.50 .69 25 25 25 28 40 57 57 68 2. Blue numerals are in millimeters and kilograms.0 16.4 6.50 .56 2.53 12. .28 1.50 . Refer to pages 116-120 for full materials description. Seat: HF 701F8M SW701F8M 1/2-2 (no 1 1/4) Trim: 316 Seat: HF 701MM SW701MM 1/2-2 (no 1 1/4) Trim: Monel Seat: HF 701MB8 SW701MB8 Trim: 316 Disc/Seat: HF 701MBS SW701MBS Trim: Monel Seat: HF 701 CHECK CLASS 800 (PN 130) A105 Body/Bonnet 1975 PSI @ 100°F (136.56 2.50 4.7 19.50 .Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) ■ ■ ■ ■ ■ ■ Conventional Port For other ratings see pgs.5 32.9 3.28 1.75 1.00 1.75 3.7 12.7 12.75 95 95 95 102 117 159 159 197 1.5 25. Petroleum (Refined) ● ● Sodium Perborate ● ● ● Hydraulic Oil ● ● Oils. Refined ● ● Natural Gas ● ● Gasoline. Unleaded Shellac (Orange) ● ● ● ● ● Gasoline. ● ● ● Pentane Kerosene Ethylene Glycol ● ● ● ● ● ● ● ● ● ● ● ● ● ● Ethyl Chloride (Dry) ● Sodium Sulfate ● Potassium Carbonate ● Sodium Silicate Sodium Sulfide ● ● ● ● ● ● ● ● Jet Fuel ● ● ● Palmitic Acid ● Ethyl Alcohol Freon 12. Leaded ● Shellac (Bleached) Soap Solutions (Stearates) ● ● ● ● Pyrogallic Acid ● ● Ammonium Phosphate FLUID Naphtha Amines—Mixed Ammonia (Aqueous) ● ● NE NE FLUID ETH YLEN E PR OPO LYEN NEO E (E PR) PRE BUN AN VITO N Fuel Oil ● ● Methyl Alcohol NE ● Acetylene Acetone ETH YLEN E PR OPO LYEN NEO E (E PR) PRE FLUID BUN AN VITO N FLUID BUN AN VITO N NE ETH YLEN E PR OPO LYEN NEO E (E PR) PRE for Service Fluids Commonly Used in Vogt “ZL” Check Valves 101 ● ● ● ● ● Sulfur Dioxide (Dry) ● Tar & Tar Oil ● Toluene ● ● Vegetable Oils ● Xylene ● Zinc Hydrosulfite ● ● ● ● ● ● ● ● . 13. Petroleum (Sour) ● Hydrocarbons ● ● Oxygen (Cold) ● Hydrogen Gas (Cold) ● ● ● Carbon Bisulfide ● ● ● Hydrogen Sulfide (Dry) ● ● ● ● ● Sodium Sulfite ● ● ● ● ● Sodium Thiosulfate (Hypo) ● ● ● ● ● Steam (212° F) ● ● Potassium Cyanide ● ● ● Linseed Oil ● ● Potassium Hydroxide ● ● ● Lubricating Oil ● ● Potassium Nitrate ● ● ● ● Magnesium Hydroxide ● ● ● ● Potassium Permanganate ● ● Magnesium Hydrox. Sour ● ● ● ● ● Barium Carbonate ● ● Beet Sugar Liquors ● ● Butane ● ● Cane Sugar Liquors ● ● ● ● Benzene (Beneol) ● Castor Oil ● ● Caustic Soda ● ● Crude Oil ● Diesel Oils ● Dowtherms ● ● Glue ● ● Glycerin ● ● Nitrogen ● ● Sodium Cyanide ● ● ● ● ● Oils. *Because of the influence of contaminants in corrosive chemical solutions. Mineral ● ● Sodium Nitrate ● Oils. Natural ● ● ● ● ● ● ● ● Sodium Chromate ● ● ● Ammonia (Anhydrous) ● ● Gasoline. Animal ● ● Sodium Hydroxide ● ● ● ● ● ● Oils. 100 • Indicates the ZL Ring material suggested for use in a given fluid or service application.Flow Control Division Vogt Valves Compound Selection Guide* ETH YLEN E PR OPO LYEN NEO E (E PR) PRE ● ● Furfural Air ● ● ● Alcohols ● ● ● ● ● ● ● Mineral Oil ● Gas. 22 ● Glucose BUN AN VITO N Sodium Carbonate Naphthalene Asphalt ● ● ● Gasoline. Fuel ● ● Sodium Metaphosphate ● ● ● ● Oils. (Hot) ● ● ● ● Potassium Phosphate ● ● Magnesium Sulfate ● ● ● ● Potassium Sulfate ● ● Potassium Sulfide ● ● Potassium Sulfite ● ● Propane ● ● ● ● Fish Oils ● ● ● ● ● Maleic Acid Mercury ● ● Methane ● ● See Valves on Page No. this table is intended only as a general guide and does not constitute a recommendation or guarantee. Manufactured ● Mustard ● Gas. Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Full Port 1975 PSI @ 100°F (136.8 3.12 1.06 4.28 1.6 25.0 7.25 2.8 47.25 2.62 6.69 3.5 32.6 3.00 4.5 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.94 5.9 7. For Cv factors see page 123.5 38.1 32.50 4.5 11.7 19. 102 .25 7.56 3.4 1. 112-115 SERIES NUMBER Threaded Socket Weld 13701 SW13701 Trim: 13% Cr.56 2.28 1.00 102 117 159 159 197 229 1.5 6.00 12.50 4.50 28 40 57 57 68 89 2. Seat: HF 13701 CHECK CLASS 800 (PN 130) A105 Body/Bonnet Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16.34 Bold face numerals are in inches and pounds. Valve Matrix KK.75 9.5 17. Blue numerals are in millimeters and kilograms.5 16.25 6.50 .2 BAR @ 38°C) ■ ■ ■ ■ ■ ■ For other ratings see pgs.7 21.75 1.53 2. Dimensions Size NPS 1/2 3/4 1 1-1/4 1-1/2 2 DN 15 20 25 32 40 50 4.9 50.94 65 78 114 114 125 151 . 1920 PSI @ 100°F (132. 112-115 54853.34 For other ratings see pgs.18 3.46 3. Blue numerals are in millimeters and kilograms.0 20.6 26.2 BAR @ 38°C) ■ Union Bonnet ■ Flat Gasket Joint ■ Horizontal or Vertical Upward Flow ■ Ball Check ■ Integral Seat ■ ASME B16.7 10. Refer to pages 116-120 for full materials description.6 16.7 1.0 1.31 5.8 7.9 7.50 5.38 3.79 4.88 5. Dimensions Size NPS 1/2 3/4 1 1-1/4 1-1/2 2 DN 15 20 25 32 40 50 3.00 14.46 4.6 A-End-to-End B-Nut-Across-Corners C-Seat Diameter Weight For Cv factors see page 123.7 3.75 86 99 135 140 143 171 2. 54863 H & V CHECK CLASS 800 (PN 130) SERIES NUMBER Body/Bonnet Threaded A105 54853 Socket Weld SW54853 Trim: 18% Cr.55 .5 38.53 2.74 3.8 2.8 5. Valve Matrix LL.06 1.9 32.Flow Control Division Vogt Valves Forged Check Valves Class 800 (PN 130) Full Port 1975 PSI @ 100°F (136. 103 .4 BAR @ 38°C) F316/F316L 54863 – Trim: 316 Bold face numerals are in inches and pounds.3 3.81 1.62 6.7 2.94 70 81 88 96 113 125 .9 50.5 4.28 1. 25 6. Valve Matrix GG.4 1.9 4.88 4. NPS 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 DN 8 10 15 20 25 32 40 50 3.39 . For Cv factors see page 123.88 3.97 1.39 .0 35. B9091 9091 CHECK CLASS 800 (PN 130) A105 Body/Bonnet Union Bonnet Flat Gasket Joint Horizontal Type Piston Check/Ball Check Renewable Seat ASME B16.44 1.2 1.50 2.88 9.8 4.56 3.69 3.9 2.12 3.25 79 79 86 102 127 159 171 210 .34 SWB9091 Trim: 13% Cr.72 .12 24 24 28 38 44 60 68 79 2.9 9.94 .8 2.2 6.38 2.88 64 64 73 79 90 99 116 124 .38 4.12 3.2 6.4 9.9 12. 112-115 SERIES NUMBER Threaded Socket Weld 9091 SW9091 Trim: 13% Cr.00 6.2 BAR @ 38°C) For other ratings see pgs. 104 .19 1.50 .50 2.6 10.12 1.1 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.7 2.6 30.00 5.75 8.4 16.7 18.3 1.50 1.3 24.94 1. Seat 18% Cr.75 2.Flow Control Division Vogt Valves Forged Check Valves ■ ■ ■ ■ ■ ■ Class 800 (PN 130) 1975 PSI @ 100°F (136.5 23.12 3.2 14.2 36. Blue numerals are in millimeters and kilograms.6 47. Ball Ball Check Dimensions Size Bold face numerals are in inches and pounds.56 4. 7 12.50 114 130 149 178 216 .Flow Control Division Vogt Valves Forged Check Valves Class 1500 (PN 260) Conventional Port 3705 PSI @ 100°F (255.00 14. . 105 NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 8.10.00 10.50 .75 1. Disc/Seat: HF Round Bolted Bonnet Spiral Wound Gasket Horizontal Type Piston Check Integral Hard Faced Seat ASME B16.50 .1 17. Refer to pages 116-120 for full materials description.1 28.7 19.F.34 Flanged Ends: 1/4" R. 112-115 SERIES NUMBER 15593 CHECK CLASS 1500 (PN 260) A105 Body/Bonnet 15593 Trim: 13% Cr.4 7. Bold face numerals are in inches and pounds.0 21.50 9.3 17.38 12. Blue numerals are in millimeters and kilograms.75 5.03 6.06 3.4 35.7 9.0 37.12 5.5 BAR @ 38°C) ■ ■ ■ ■ ■ ■ For other ratings see pgs. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Valve flanges conform to ASME Standard B16. Valve Matrix NN.12 78 78 112 128 155 4.00 8.88 7.00 12.0 36.50 216 229 254 305 368 3.12 1.5 81. Seat: HF 15593FHF Trim: 13% Cr.06 4.41 5.5 16.0 For Cv factors see page 123.0 37.5 and end-to-end dimensions conform to ASME Standard B16. Dimensions Size NPS 1/2 3/4 1 1-1/4 1-1/2 2 DN 15 20 25 32 40 50 4.50 40 40 57 68 68 89 3.03 5.75 1.50 .4 3.00 114 114 159 197 197 229 1.5 54.7 12.5 BAR @ 38°C) For other ratings see pgs.9 29.5 29.2 3.4 35.6 13. Blue numerals are in millimeters and kilograms.69 2.56 2. For Cv factors see page 123.41 5.4 13.7 19.Flow Control Division Vogt Valves Forged Check Valves Class 1500 (PN 260) Conventional Port ■ Round Bolted Bonnet ■ Spiral Wound Gasket ■ Horizontal Type ■ Piston Check/Ball Check ■ Integral Hard Faced Seat ■ ASME B16.06 3.12 1.50 .7 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.56 1.1 7. Seat: HF 15701 CHECK CLASS 1500 (PN 260) A105 Body/Bonnet 15701FHF SW15701FHF Trim: 13% Cr.12 78 78 112 128 128 155 .1 8.50 4.12 1.34 3705 PSI @ 100°F (255.25 2.25 7.03 6.4 28.1 28. 112-115 SERIES NUMBER Threaded Socket Weld 15701 SW15701 Trim: 13% Cr. 106 .38 12.9 18.1 6.75 7.75 9. Disc/Seat: HF B15701 SWB15701 Trim: 18% Cr.06 4.50 6.4 24. Ball Seat: HF Ball Check Bold face numerals are in inches and pounds. Valve Matrix NN.69 3. 1622 Y PATTERN CHECK LTD CLASS 1690 (PN 290) A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 1610 SW1610 Trim: 13% Cr. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.53 1.Flow Control Division Vogt Valves Forged Check Valves – For Oil Hydraulic Service Class 1690 (PN 290) Conventional Port ■ Welded Bonnet ■ “Y” Pattern ■ Horizontal or Vertical Upward Flow ■ Spring Control ■ Hard Faced Piston Check ■ Integral Hard Faced Seat ■ ASME B16.75 2.81 . 112-115 1610.1 38.16 1.4 . Blue numerals are in millimeters and kilograms.03 5.9 1.9 4.72 5.0 1. (302 SS Spring) Disc/Seat: HF Bold face numerals are in inches and pounds.69 21 21 30 43 43 2.1 10.50 102 102 130 190 190 .75 1.69 1.7 19. (302 SS Spring) Disc/Seat: HF F22 Cl 3 (2 1/4% Cr.8 4.50 7.0 9.75 3. 107 NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 4.34 LTD Pressure Class 4225 PSI @ 100°F (291.7 12.81 1.53 12.1 4.00 4.9 38.03 70 70 94 128 128 .2 23.4 BAR @ 38°C) For other ratings see pgs.50 .00 5.50 .4 10.12 7.1 23.) Body/Bonnet SERIES NUMBER Threaded Socket Weld 1622 SW1622 Trim: 13% Cr. 75 .12 8.16 1. (302 SS Spring) Disc/Seats: HF F11. 2622 Y PATTERN CHECK LTD CLASS 2680 (PN 460) For other ratings see pgs.53 1.9 4. 3 (2-1/4% Cr. Cl.53 12. 2611.94 1.94 21 29 29 49 49 2.2 1. Cl.7 19.75 3.1 BAR @ 38°C) THD: 6250 PSI @ 100°F (431.) 2622 SW2622 Trim: 13% Cr.81 1.25 8.1 16. pages 112-115.1 4. Dimensions Size A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.50 . Blue numerals are in millimeters and kilograms.34 LTD Pressure Class *Threaded valves limited to Class 2500 Applications under ASME B16. (302 SS Spring) Disc/Seats: HF F22.75 3.0 BAR @ 38°C)* 2610.16 1.25 102 130 130 210 210 .75 5. 2 (1-1/4% Cr.0 9.Flow Control Division Vogt Valves Forged Check Valves – For Air.1 38.9 38.1 36.12 5. Water & Oil Service Class 2680 (PN 460) Full Port SW: 6700 PSI @ 100°F (462.34. 112-115 SERIES NUMBER Body/Bonnet Threaded* Socket Weld A105 2610 SW2610 Trim: 13% Cr.8 4.1 .1 19.0 33.38 5.1 9. Bold face numerals are in inches and pounds.38 70 95 95 137 137 .00 5.75 1. See 2500 LTD Class Press/Temp tables.3 15.) 2611 SW2611 Trim: 13% Cr. 108 NPS 1/2 3/4 1 1-1/2 2 DN 15 20 25 40 50 4. (302 SS Spring) Disc/Seats: HF ■ Welded Bonnet ■ “Y” Pattern ■ Horizontal or Vertical Upward Flow ■ Spring Control ■ Hard Faced Piston Check ■ Integral Hard Faced Seat ■ ASME B16. 75 68 68 71 89 97 99 108 121 .4 2.38 4.12 3. Valve Matrix SS.7 13.25 4.53 12.69 3.2 20. B1551 (1/4 .2 9. Screw Bonnet Flat Gasket Joint Horizontal Type Piston Check Integral Seat 1551 CHECK TYPE 3000 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 1551 SW1551 Trim: 13% Cr.7 12.38 2. Blue numerals are in millimeters and kilograms.94 1.7 2.56 .88 4.75 2.12 24 24 28 38 44 60 68 79 2.50 .12 1.7 6.75 8.1 1.28 1.7 12.5 1.50 .7 14. 109 .81 3.7 A-End-to-End B C D-Seat Diameter Weight For Cv factors see page 123. Ball Ball Check Bold face numerals are in inches and pounds.00 5.06 1.69 2.6 27.0 32.9 BAR @ 38°C) NON-SHOCK PRESSURE Temperature not to exceed 450°F.9 2.94 .9 6. Not recommended for steam or dry gas service.50 3.00 6.81 3.4 3.0 8.12 3. Refer to pages 116-120 for full materials description.25 6.7 3.7 21.50 1.81 1.25 79 79 86 102 127 159 170 210 .50 .1 1.7 34.69 2.5 38.3/4 Only) SWB1551 Trim: 18% Cr.Flow Control Division Vogt Valves Forged Check Valves – For Oil Hydraulic Service Type 3000 ■ ■ ■ ■ ■ 3000 PSI @ 100°F (206. Dimensions Size NPS 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 DN 8 10 15 20 25 32 40 50 3.8 15. ■ Screw Bonnet ■ Flat Gasket Joint ■ Horizontal or Vertical Upward Flow ■ Spring Control ■ Piston Check ■ Renewable Seat Not recommended for steam service.4 15.6 30.44 9.75 2.9 BAR @ 38°C) NON-SHOCK PRESSURE Temperature not to exceed 450°F.5 5.97 1.39 .25 6.50 .1 1. Blue numerals are in millimeters and kilograms.6 3.50 3.81 3.00 6.39 .3 24.75 8.94 .75 3.Flow Control Division Vogt Valves Forged Check Valves – For Air. Bold face numerals are in inches and pounds.8 8. Dimensions Size NPS 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 DN 8 10 15 20 25 32 40 50 3.39 .69 3.6 2.00 5.75 2.81 4.7 18.6 2.2 36.4 3.7 13.12 24 24 28 38 44 60 68 79 2.19 1.94 1.5 20.50 1. 2191 CHECK TYPE 3000 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 2191 SW2191 Trim: 13% Cr.7 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description. Water & Oil Service Type 3000 3000 PSI @ 100°F (206.12 3.25 79 79 86 102 127 159 170 210 .9 9.8 34.72 .9 9. 110 .38 2.38 4.9 12.5 2.9 6.00 3.12 3.1 1.12 1.5 1.25 4.1 9.94 70 70 76 89 97 97 108 125 . 39 .19 1.12 3. Not recommended for steam service.8 BAR @ 38°C) Full Port Temperature not to exceed 450°F.2 36.50 102 127 159 170 210 216 1.38 2. Water & Oil Service Type 6000 NON-SHOCK PRESSURE 6000 PSI @ 100°F (413.12 3.44 9.75 2. ■ Screw Bonnet ■ Flat Gasket Joint ■ Horizontal or Vertical Upward Flow ■ Spring Control ■ Piston Check ■ Renewable Seat 4881 CHECK TYPE 6000 A105 Body/Bonnet SERIES NUMBER Threaded Socket Weld 4881 SW4881 Trim: 13% Cr.44 4.38 38 44 60 68 79 86 3.97 1.00 6.6 30.5 23.6 10.7 7.88 79 92 99 113 121 149 .2 14.9 2.6 5.8 23.50 1.25 6.Flow Control Division Vogt Valves Forged Check Valves – For Air.6 A-End-to-End B C D-Seat Diameter Weight Refer to pages 116-120 for full materials description.00 5.69 3. 111 .6 3.6 16. Dimensions Size NPS 1/2 3/4 1 1-1/4 1-1/2 2 DN 15 20 25 32 40 50 4.50 .62 3.3 24.75 8.9 51.9 12.3 6.4 36.7 18.25 8.88 4.75 5. Blue numerals are in millimeters and kilograms. Bold face numerals are in inches and pounds.72 . Flow Control Division Vogt Valves Pressure-temperature Ratings for Vogt products Class 800 (PN 130) (Standard) PRESSURE (PSIG) (1) (1) (2) (1) A182F316H (1) (4) (7) A350LF2 A182F9 (1) (5) & (6) A182F11 C12 (1) (1) (2) (1) A105 A182F5 A182F316 A182F22 C13 A105 A182F5 A182F316 -20 to 100 1975 2000 1920 1920 1975 2000 2000 2000 3705 3750 200 1800 1985 1655 1655 1800 2000 2000 2000 3375 300 1750 1910 1495 1495 1750 1940 1925 1940 400 1690 500 1595 1880 1370 1370 1775 1275 1275 1690 1880 1850 1595 1775 1775 600 1460 1615 1205 1205 1460 1615 650 1430 1570 1185 1185 1430 700 1420 750 1345 1515 1160 1160 1410 1140 1140 800 1100 1355 1125 850 715 1290 1115 900 460 985 950 275 735 1000 140 530 1050 – 385 Service Temp (°F) (1) (4) (9) Class 1500 (PN 260) (Standard) PRESSURE (PSIG) (1) (1) (5) (1) (4) (9) A182F316H (1) (4) (7) A350LF2 3600 3600 3725 3095 3280 3580 1880 3170 1775 2995 1615 1615 1570 1570 1420 1515 1345 1420 1125 1100 1115 1105 1030 935 – (1) A182F9 (1) (5) & (6) A182F11 C12 (1) (5) A182F22 C13 3705 3750 3750 3750 3095 3375 3750 3750 3750 2795 2795 3280 3640 3610 3640 3530 2570 2570 3170 3530 3465 3530 3325 2390 2390 2995 3325 3325 3325 2735 3025 2255 2255 2735 3025 3025 3025 1570 2685 2940 2220 2220 2685 2940 2940 2940 1515 1515 2665 2840 2170 2170 2665 2840 2840 2840 1420 1420 2520 2640 2135 2135 2520 2660 2660 2660 1355 1355 1355 2060 2540 2110 2110 2060 2540 2540 2540 715 1300 1300 1300 1340 2415 2090 2090 1340 2435 2435 2435 1105 460 1200 1200 1200 860 1850 2075 2075 860 2245 2245 2245 1030 275 1005 850 1005 515 1370 1930 1930 515 1885 1595 1885 935 140 675 575 695 260 995 1750 1750 260 1270 1080 1305 915 – 460 385 465 – 720 – 1720 – 855 720 875 1100 – 265 – 815 – 300 255 295 – 495 – 1525 – 565 480 550 1150 – 165 – 630 – 200 165 180 – 310 – 1185 – 375 310 345 1200 – 95 – 495 – 140 100 110 – 170 – 925 – 255 190 205 1250 – – – 390 – – – – – – – 735 – – – – 1300 – – – 310 – – – – – – – 585 – – – – 1350 – – – 255 – – – – – – – 480 – – – – 1400 – – – 200 – – – – – – – 380 – – – – 1450 – – – 155 – – – – – – – 290 – – – – 1500 – – – 110 – – – – – – – 205 – – – – SEE NOTE ON PAGE 113 FOR RATING RESTRICTIONS. 1 bar = 100kPa = 14.504 psi 112 . Carbon of . Socket Weld and Butt Weld End Valves End Unions Service Temp (°F) 150 (PN20) (1)(4)(9) A105 300 (PN50) (1)(4)(9) A105 600 (PN110) 1500 (PN260) (1)(4)(9) (1)(4)(9) A105 A105 100 285 740 1480 200 260 675 300 230 655 400 200 500 (3) (5) A182F22 CI3 4225 4225 4175 4080 4055 4055 4035 4005 3885 3790 3620 3380 2720 1980 1330 830 525 315 (3) (4) (9) A105 6250 6250 6250 6250 6250 5940 5825 5780 5250 4285 2785 1785 1110 600 – – – – (3) (5) (6) A182F11 CI2 6250 6250 6250 6250 6250 6250 6250 6110 6070 6000 5645 4895 3445 2520 1680 1120 720 440 (3) (5) A182F22 CI3 6250 6250 6180 6035 6000 6000 5965 5930 5750 5605 5355 5000 4075 3040 2040 1280 800 480 (3) (4) (9) A105 6700 6700 6700 6700 6700 6370 6245 6195 5630 4595 2985 1915 1190 650 – – – _ (3) (5) (6) A182F11 CI2 6700 6700 6700 6700 6700 6700 6700 6550 6505 6430 6050 5245 3700 2725 1820 1210 780 480 (3) A11 F22 CI3 6700 6700 6625 6470 6430 6430 6395 6355 6165 6010 5740 5360 4385 3290 2205 1385 865 520 NOTE: THE FOLLOWING RESTRICTIONS CORRESPOND TO THE CHARTS ON PAGES 112 AND 113. 650 125 535 1075 2685 650 2180 4360 700 110 535 1065 2665 700 2155 4310 750 95 505 1010 2520 750 – – 800 80 410 825 2060 800 – – 850 65 270 535 1340 850 – – 900 50 170 345 860 900 – – 950 35 105 205 515 950 – – 1000 20 50 105 260 1000 – – 1 bar = 100kPa = 14.34-96. (7) A350 LF2 is suitable to -50°F at the -20°F to 100°F Pressure Rating. Socket Weld.Flow Control Division Vogt Valves Pressure-temperature Ratings for Vogt products PRESSURE (PSIG) Service Temp (°F) -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 Class 800 (PN 130) Class 1500 (PN 260) Class 1690 (PN 290) Class 2500 (PN 420) Class 2680 (PN 460) (Limited) (Limited) (Limited) (Limited) (Limited) (3) (4) (9) A105 2000 2000 2000 2000 2000 1900 1865 1850 1680 1375 895 575 350 180 – – – – (3) (5) (6) A182F11 CI2 2000 2000 2000 2000 2000 2000 2000 1955 1945 1920 1805 1565 1070 745 495 330 210 130 (3) (5) A182F22 CI3 2000 2000 1980 1935 1920 1920 1905 1900 1840 1795 1715 1600 1275 895 600 380 235 145 (3) (4) (9) A105 3750 3750 3750 3750 3750 3565 3495 3470 3150 2570 1670 1070 660 340 – – – – (3) (5) & (6) A182F11 CI2 3750 3750 3750 3750 3750 3750 3750 3665 3645 3600 3385 2935 2040 1445 960 640 410 250 (3) (5) A182F22 CI3 3750 3750 3705 3620 3600 3600 3580 3555 3450 3365 3215 3000 2405 1740 1170 730 460 275 (3) (4) (9) A105 4225 4225 4225 4225 4225 4015 3940 3910 3550 2895 1880 1205 745 390 – – – (3) (5) & (6) A182F11 CI2 4225 4225 4225 4225 4225 4225 4225 4130 4105 4055 3815 3305 2300 1640 1095 730 470 285 PRESSURE (PSIG) Threaded.035. 113 . (8) Ratings are in accordance with MSS-SP-83-1995. Limited Class. 1315 3280 300 2655 5310 (3) Ratings are in accordance with ASME B16. (9) Only killed steel shall be used above 850°F. Flanged Threaded. Standard Class. Do not use above 1000°F.34-96. 635 1270 3170 400 2565 5130 170 600 1200 2995 500 2425 4850 (4) Permissible but not recommended for prolonged use above 800°F. 600 140 550 1095 2735 600 2220 4440 (5) Permissible but not recommended for prolonged use above 1100°F. 3705 100 3000 6000 1350 3375 200 2735 5470 (2) F316 Stainless Steel containing Max. Service Temp (°F) 3000 (8) A105 6000 (8) A105 (1) Ratings are in accordance with ASME B16.504 psi (6) Use Normalized and Tempered material only. 6 182.2 158.2 243.5 257.1 208.0 231.7 – 20.9 158.3 255.7 47.1 78.1 138.2 103.0 – – – – 725 – – – 18.4 – 114.5 (1) A182F9 (1) (5) & (6) A182F11 C12 (1) (5) A182F22 C13 258.6 – – – – – – 14.4 57.6 214.0 48.7 123.4 226.2 116.0 23.2 95.2 (1) A182F9 (1) (5) & (6) A182F11 C12 (1) (5) A182F22 C13 137.8 79.8 147.0 – – – – 750 – – – 15.4 39.7 211.6 103.9 137.6 145.7 226.9 137.2 137.1 425 76.4 81.6 248.6 258.504 psi – 114 SEE NOTE ON PAGE 115 FOR RATING RESTRICTIONS.6 214.7 231.5 107.1 169.1 – 19.7 136.1 169.0 175.4 67.1 201.6 50 133.8 244.8 – 28.6 77.6 78.9 Service Temp (°C) (1) (4) (9) PN 260 (Class 1500) (Standard) PRESSURE (BAR) A182F316H (1) (4) (7) A350LF2 132.4 192.0 219.1 239.9 – 40.6 103.3 112.6 240.3 74.7 150 120.7 20.0 232.1 – 99.9 200 116.2 158.4 133.0 – 60.4 158.4 214.3 98.4 137.9 102.7 93.2 22.7 144.3 248.2 500 23.4 194.0 53.9 250.5 – 35.4 132.6 92.6 100 123.8 108.1 250.3 114.3 90.2 172.5 84.5 219.0 130.3 – 17.8 550 – 32.5 193.8 – 9.9 525 13.7 77.0 107.3 114.9 231.6 144. .5 258.4 184.8 112.1 246.7 89.2 – 24.4 144.5 64.7 44.Flow Control Division Vogt Valves Pressure-temperature Ratings (metric) for Vogt products PN 130 (Class 800) (Standard) PRESSURE (BAR) (1) (1) (2) (1) A105 A182F5 A182F316 -29 to 38 136.7 – 63.4 538 9.1 675 – – – 27.5 181.9 68.5 114.7 77.3 182.9 7.8 30.6 77.7 143.8 172.4 76.4 143.1 67.7 – – – – 775 – – – 12.6 258.9 93.9 – – – – 800 – – – 9.7 132.6 – 33.2 44.3 184.6 131.4 167.8 26.1 90.8 201.5 28.0 52.4 107.1 152.6 137.0 255.5 178.1 18.4 214.5 – – – – 700 – – – 22.8 123.3 – 119.1 250 111.1 193.9 57.1 106.0 257.6 145.2 244.0 575 – 23.9 41.4 – 31.6 – 11.7 17.5 13.3 – – – – – – – 17.5 67.5 103.7 93.4 100.1 – – – – – – – 22.6 258.9 43.3 – – – – – – – 51.8 201.7 – 60.5 258.9 300 103.1 138.7 133.2 240.6 133.9 (1) (4) (9) (1) (1) (2) (1) A182F316H (1) (4) (7) A350LF2 A105 A182F5 A182F316 255.1 183.1 194.8 192.7 136.9 126.1 167.9 87.0 16.5 114.1 158.3 100.6 90.1 – 44.4 136.0 128.1 – 13.1 89.9 137.5 258.2 – 63.5 107.8 17.3 137.3 84.9 137.7 257.0 77.8 97.6 13.3 90.6 84.7 128.5 258.7 36.7 175.5 79.5 625 – 10.9 93.9 129.4 128.2 123.0 – 79.7 178.7 120.4 107.9 23.7 175.6 250.5 9.2 123.2 – – – – – – – 28.4 136.8 95.2 10.7 600 – 16.8 – 75.9 120.2 147.9 149.1 183.1 201.7 450 53.3 81.1 14.9 137.7 102.1 97.1 111.4 – – – – 816 – – – 7.5 126.9 144.7 208.8 11.4 232.8 97.4 76.1 – – – – 1 bar = 100kPa = 14.6 76.4 169.2 67.1 97.0 63.6 67.7 – 42.9 72.6 74.3 123.2 103.0 33.7 231.6 89.3 – – – – – – – 42.6 – – – – – – – 35.6 56.1 194.4 36.2 44.3 34.9 130.0 80.5 64.1 475 36.4 350 98.1 375 97.0 – 52.8 250.7 46.3 73.3 149.6 – 53.3 152.6 84.4 193.0 175.4 26.6 137.7 6.9 167.9 248.9 72.5 183.7 137.1 400 92.4 650 – 6.5 84.4 126.8 97.3 89.5 120.0 211.4 74. 8 275.9 36.9 187.4 440.6 258.0 30.6 257.5 209.6 184.8 210.6 134.5 162. (9) Only killed steel shall be used above 850°F.4 160.7 132.0 273.8 90.8 61.5 250.4 240.1 462.9 137.8 385.8 405.9 29.0 431. 6000 (8) A105 413.7 70.9 58.8 251.7 Threaded.2 112.0 73.1 (3) A11 F22 CI3 462.4 291.3 50.7 19.2 396.9 148.2 8.2 134.5 8.0 431.1 462.7 40.4 289.6 19.9 187.6 23.0 279.0 A105 258.4 168.0 45. Socket Weld.4 7.7 (3) (4) (9) A105 431.2 266.6 10.8 38.0 (3) (5) (3) (4) (9) A182F22 CI3 137.4 204.6 203.1 398.0 72.2 372.0 177.4 172.6 258.0 132.5 144.5 359.3 122.9 115.9 NOTE: THE FOLLOWING RESTRICTIONS CORRESPOND TO THE CHARTS ON PAGES 114 AND 115.8 407.1 459.0 393.9 118.7 447.6 451.8 13.3 448.1 393.0 50.7 15.0 314.3 17. 115 .6 47. (7) A350 LF2 is suitable to -50°F at the -20°F to 100°F Pressure Rating.8 – – – – – (3) (5) (6) A182F11 CI2 462.9 443.7 415.3 194.6 179.1 33.3 35.3 10.9 137.4 7.2 23.4 131.7 40.2 116.9 19.1 84.9 5.9 80.0 93.8 182.3 26.4 – – – – – (3) (5) (6) A182F11 CI2 431.2 1 bar = 100kPa = 14.6 258.0 17.9 137. Limited Class.4 291.0 30.8 180.1 26.1 10.2 86.9 297.8 410.0 160.6 258.7 375.2 243.3 (3) (5) A182F22 CI3 431.9 41.1 183.6 258.4 84.2 PRESSURE (PSIG) Threaded.9 366.9 137.5 126.6 28.6 132.1 100.7 17.4 299.8 124.8 12.8 376.0 46.9 1.6 – – – – – – – (3) (5) A182F22 CI3 291.4 140.8 281.9 137.2 223. (5) Permissible but not recommended for prolonged use above 1100°F.1 219.0 431.1 92.1 462.5 111.2 252.0 136.1 461.0 267.1 351.0 271.6 261.8 14.8 112.0 119.7 421.2 387.6 258.4 250.5 133.3 130.1 57.4 223.4 125.0 431.9 157.4 443.6 3.0 202.1 462.8 86.5 218.1 462.9 36.6 258.9 44.0 428.6 258.035.504 psi PN260 (CL1500) (1)(4)(9) A105 255.1 445.3 20.0 100.9 95.6 283.1 462.3 102.5 5.0 279.7 193.1 462.8 421.7 17.0 414.1 462.8 284.2 26.6 41.6 258.2 76.9 137.4 – – – – – (3) (5) (6) A182F11 CI2 137.Flow Control Division Vogt Valves Pressure-temperature Ratings (metric) for Vogt products PRESSURE (PSIG) Service Temp (°C) -29 to 38 50 100 150 200 250 300 350 375 400 425 450 475 500 525 538 550 575 600 625 649 PN 130 (Class 800) PN 260 (Class 1500) PN 290 (Class 1690) PN 420 (Class 2500) PN 460 (Class 2680) (Limited) (Limited) (Limited) (Limited) (Limited) (3) (4) (9) A105 137.6 236.0 52.9 (3) (5) (3) (4) (9) A182F22 CI3 258.8 237.1 248.4 376.1 67. Carbon of . Flanged and Butt Weld End Valves Service Temp (°C) -29 to 38 50 100 150 200 250 300 350 375 400 425 450 475 500 525 538 PN20 (CL150) (1)(4)(9) A105 19.6 251.8 15.1 62.0 242.3 52.4 291.1 27.7 277.0 112.8 338.9 421.4 321.4 210.6 258.6 141.1 61.7 232.0 431.7 134.4 414.2 215.6 125.8 96.7 102.34-96.5 237.2 62.9 183.4 45. Standard Class.0 415. Do not use above 1000°F.6 34.1 443.2 351.0 430.4 PN 50 (CL300) (1)(4)(9) A105 51.9 265.0 96.4 PN 110 (CL600) (1)(4)(9) A105 102.2 413.5 248. (3) Ratings are in accordance with ASME B16.8 30.2 3.4 291.7 70.1 (3) (4) (9) A105 462.8 136.6 77.0 431.5 74. (2) F316 Stainless Steel containing Max.2 13.6 258.3 100.9 137.7 51.4 456.2 – – – – – – – (1) Ratings are in accordance with ASME B16.4 291.4 291.6 258.4 291.9 133.0 A105 291.7 9.7 429.4 291.8 80.0 44.4 96.8 83.3 57.1 119.0 431.5 232.0 431.0 226.8 38.5 99.6 55.9 137.1 43.6 401.6 151.2 208.0 417.4 291.2 34.6 4.4 29.1 173.0 128.0 431.7 2.0 354.3 246.6 258.9 137.0 418.6 249.8 1.2 43.0 12.1 462.7 20.9 202. (8) Ratings are in accordance with MSS-SP-83-1995.34 -96.5 208.1 132.1 462.5 125.9 137.4 424.2 237.9 56.9 33.6 67.4 45.9 – – – – – (3) (5) & (6) A182F11 CI2 291.5 326.4 67.9 137.9 137.0 46.0 431.4 291.7 261. Socket Weld End Unions Service Temp (°C) -29 to 38 50 100 150 200 250 300 350 371 – – – – – – – 3000 (8) A105 206.1 179.9 137.4 436.1 462. (4) Permissible but not recommended for prolonged use above 800°F.0 431.5 244.3 148.6 226.5 426.7 33.0 149.6 141.2 304.4 291.2 255.0 431.4 6.4 – – – – – (3) (5) & (6) A182F11 CI2 258.2 21.9 69.9 280.4 291.1 299.3 248.8 36.0 287.5 235.4 281.1 462.6 87. (6) Use Normalized and Tempered material only.4 291.9 137.6 52.2 293.2 17. It may also be used in fluids having a pH range of 0-14. This virgin TFE material needs no corrosion inhibitor in its composition and its self-energizing shape assures superior service with low gland bolting loads in high pressure liquid and dry gas applications. it can be reoriented for valves used in vacuum and/or combination vacuum/pressure service. Since this packing has directional sealing. Temperature range: -120°F to 500°F (-84° to 260°C). It may be used in fluids having a pH range of 0-14.Flow Control Division Meeting the Demands of Today Asbestos-Free Valves Asbestos-Free Packing Asbestos-Free Gasket SAFE—EFFICIENT in retaining high and low temperature media ADVANCED TECHNOLOGY PROVIDES: ■ ■ ■ ■ ■ ■ ■ ■ ■ Environmental acceptance Elimination of media contamination Leak-proof integrity High thermal conductivity Self-lubricating operation Shrinkage resistance Corrosion resistant inhibitor Less frequent maintenance Longer service life Vogt Valves STANDARD PACKING Vogt standard valves are packed with one of the following asbestos-free packing sets: FLEXIBLE GRAPHITE PACKING A 95% by weight minumum carbon packing set that consists of a cylindrical ring of flexible graphite packing supported on the top and bottom with braided graphite filament packing rings. OTHER PACKING Other packing sets can be placed in Vogt valves at the user’s option. 116 . The packing set contains a dispersed and embedded active corrosion inhibitor to protect against stem pitting. The packing has minimal residues as follows: Leachable Chlorides: 100PPM Maximum Total Chlorides: 500PPM Maximum Total Sulfur: 1000PPM Maximum PTFE: None MOLDED TFE TEFLON SHAPED PACKING Vogt valves that have a series number suffixed with the letter “T” are packed with a molded shaped TFE packing. Fittings.Flow Control Division Cross-Reference of ASTM Material Specifications Covering Cast and Forged Valves. Flanges and Unions Material Forgings Castings Wrought Fittings Carbon Steel Cold Temperature Service Carbon-1/2 Moly Alloy Steel High Temperature Service A105 A350-LF2 A216-WCB A234-WPB A420-WPL6 A182-F1 A217-WC1 A352-LC1 A234-WP1 A350-LF3 A182-F2 A352-LC3 A420-WPL3 3-1/2 Nickel Alloy Steel Low Temperature Service 1/2 Cr-1/2 Mo Alloy Steel 1/2 Cr-1/2 Mo-1 Ni Alloy Steel 3/4 Cr-1 Mo-3/4 Ni Alloy Steel 1 Cr-1/2 Mo Ailoy Steel 1-1/4 Cr-1/2 Mo Alloy Steel A217-WC4 A217-WC5 A182-F12 CL2 A182-F11 CL2 2-1/4 Cr-1 Mo Alloy Steel 5 Cr-1/2 Mo Alloy Steel 5 Cr-1/2 Mo Alloy Steel 9 Cr-1 Mo Alloy Steel 13 Cr Alloy Steel Type 304 Stainless Steel (18 Cr-8 Ni) Standard Low Carbon High Temperature Service Type 310 Stainless Steel (25 Cr-20 Ni) Type 316 Stainless Steel (16 Cr-12 Ni-2 Mo) Standard Low Carbon High Temperature A182-F22 CL3 A182-F5 A182-F5a A182-F9 A182-F6 A182-F304 A182-F304L A182-F304H A182-F310H A234-WP12 CL2 A234-WP11 CL2 A217-WC6 A217-WC9 A217-C5 A217-C12 A743-CA15 A351-CF3 A351-CF8 A351-CK20 A182-F316 A182-F316L A182-F316H A234-WP22 CL3 A234-WP5 A234-WP9 A403-WP304 A403-WP304L A403-WP304H A403-WP310 A403-WP316 A403-WP316L A403-WP316H A351-CF3M A351-CF8M Type 317 Stainless Steel (18 Cr-13 Type 321 Stainless Steel (18 Cr-10 Standard High Temperature Service Type 347 Stainless Steel (18 Cr-10 Standard High Temperature Service Type 348 Stainless Steel (18 Cr-10 Standard High Temperature Service Ni-3 Mo) Ni-Ti) A403-WP317 A182-F321 A182-F321H A403-WP321 A403-WP321H Ni-Cb) A182-F347 A182-F321H A351-CF8C A403-WP347 A403-WP347H Ni-Cb) A182-F348 A182-F348H 117 A403-WP348 A403-WP348H Vogt Valves . 1. and greater strength than F11 are needed.) RA Min.60 .35 Si 0. Grade F11.02 Cb 0.00 8.030 Max.30 .040 Max.50 0. Class 3 – 2 1/4% Chromium 1% MoIybdenum Where elevated temperature. psi(MPa) YS Min.10. Do not use for service temperatures above 1000°F.030 Max 0.030 1.15 0.Flow Control Division Vogt Valves Forging Materials Chemistry Element – % Composition Mechanical Properties Chemistry Element – % Composition ASTM A105 Carbon Steel Where temperatures are moderate and corrosion resistance is not critical. 0. psi(MPa) YS Min. Has a restricted carbon range for high temperature strength above 1000°F.030 Max.00 Max 10.10 .020 .65 TS Min. C Mn P S Si Ni Cr Mo 0. Class 2 – 1 1/4% Chromium 1/2% MoIybdenum To minimize graphitization encountered with carbon and carbon moly steels at high temperatures.000(380) 20% 40% 179-217 ASTM A182.24 Mn 1.50 Mechanical Properties ASTM A182.040 Cr 0. psi(MPa) YS Min.0.1. 0.1.00 .00 .06 V 0. S 0. Hardness.00 .00 .65 TS Min.0.50 Max 0.00 0. 0.015 . C Mn P S Si Cr Mo 0.3.015 .00 . 0.10 2.6.00 Max.) RA Min. 75.00 1. Hardness.000(485) 40.0. C 0.00 0. Bhn -50°F Charpy Energy (Ft. .1.035 0. psi(MPa) EL (2” Min.00 TS Min. psi(MPa) YS Min.24 Mn 1.00 16.3.0.040 Max. 187 TS Min./Lb.44 . psi(MPa) EL (2” Min.) RA Min.030 1.02 Total Residuals = 0.18.30 .1.000(515) 40. Grade F9 – 9% Chromium For services where the higher chrome alloys are preferred and where high temperature stability and oxidation resistance of the lower alloy steels are inadequate.000(485) 36.00 . 2.20 .06 V 0. 75. C Mn P S Si Cr Mo 0.000(250) 22% 30% Max.15 Max.040 Max.035 Max.50 TS Min. 197 Min.) RA Min. Grade F316.00 .50 .15 Max.02 Cu 0.000(515) 30.0.10 TS Min.20 Pb 0.0.000(515) 30.000(275) 20% 30% 143-207 ASTM A182. Has restricted carbon level to minimize sensitization.20 Mo 0.0. Grade F22.02 Total Residuals = 0. psi(MPa) EL (2” Min. psi(MPa) YS Min.0. Impact (J) 15(20) 12(16) ASTM A182.030 Max.20 . Hardness.0.20 Ni 0.00 .0.87 .0.00 Max 10.020 .30 P .20 Pb 0.1.000(585) 55.0. Bhn 70. Bhn 70.80 .015 .15 . psi(MPa) YS Min. psi(MPa) YS Min.000(485) 40. 0.15 .015 . 0.000(250) 22% 30% Max.0.00 2. psi(MPa) EL (2” Min. 0.) RA Min. surface stability.0.02 Cb 0.00 2.000(275) 20% 35% 143-217 ASTM A182.0.0.0. .) RA Min. psi(MPa) EL (2” Min.30 .) Average of Each Set of 3 Specimen For One Specimen 70. TS Min.00 .035 0.000(205) 30% 30% .60 . ASTM A350. Hardness.04 .00 16.1.030 Max.000(485) 36. Bhn 75.44 . Hardness. C Mn P S Si Ni Cr Mo 0. psi(MPa) YS Min.000(310) 20% 30% 156-207 C Mn P S Si Cr Mo 0. Bhn 70.00 118 TS Min. S 0. LF2 Where cold temperature (-50°F) impact strength is essential.50 Max 4.2.50 0.00 Max. psi(MPa) EL (2” Min. 0.60 .) RA Min. Grade 5 – 4-6% Chromium 1/2% MoIybdenum With moderately corrosive fluids and in oil refineries where high temperature stability and oxidation resistance of the lower alloy steels are inadequate.000(205) 30% 30% ASTM A182. psi(MPa) EL (2” Min. C 0.20 Mo 0.30 .35 Si 0. Grade F316H – 18% Chromium 8% Nickel 2-3% MoIybdenum For corrosion resistance applications where extreme high temperature service is expected.040 Cr 0. Bhn 85.90 . 0. Grade F316L – 18% Chromium 8% Nickel 2-3% MoIybdenum For corrosion resistance applications where high temperature strength is required.50 .0.015 .040 Max.13 C Mn P S Si Ni Cr Mo 0.14.15 Max.00 .00 .02 Cu 0.035 0.50 Max 2.20 Ni 0.0. Hardness.00 .14.18.30 P .) RA Min. psi(MPa) EL (2” Min. 18.13 RCoCr -A Material used for Cobalt castings.15 .17.00 .00 0. .0.15 . .00 3.00 . 0.00 2.00 Max 16.3 .040 Max . 2.040 Max. the cast equivalent to type 410 Stainless Steel.3.Flow Control Division Vogt Valves Valve Trim Materials Description & General Use Chemistry Element % Composition Description & General Use Chemistry Element % Composition 13% Chromium Stainless Steel Type 410 ASTM A479 This stainless steel material lends itself readily to hardening by heat treatment and is excellent for contacting parts such as stems. C Mn Si Ni Cr 0. C Mn P S Si Cr Ni Mo .0 Ni 9. 2.. .25 Max. .00 .00 Max.5 . 1. gates.08 Max 1. .15 . C Ni Co Cr Mo W 18% Chromium 8% Nickel.00 Max.040 Max.0 Max. Nickel-Copper Monel Alloy K500 FED-SPEC QQ-N-286F Class A C Mn S Ni Si Fe Al Ti Cu P Zn Pb Sn .02 Max.15 Max.5 3.03 Max.50 Fe Si Mn V P S 4. Grade N 10276 Hastelloy C-276 A high nickel alloy with exceptional resistance to corrosive attack by chlorine gas.0 1.4 1. 2% Molybdenum Stainless Steel Type 316 Type 316L ASTM A182 Provides excellent resistance to corrosive media at high temperatures and toughness for service at low temperatures.50 Max 63. Has excellent corrosion resistance in chlorine and alkylation service.5 27.00 .00 Max Cr Ni Cu Cb +Ta 15. give extended service life and troublefree operation.50 Max. . and Check Valves.00 .010 Max.60 Max.00 Precipitation Hardened Stainless Steel A564.50 Max Cr 18.9-1. Chromium and Boron Alloy 13% Chromium Stainless Steel Type 416 ASTM A582 High quality stainless steel yoke nut material having excellent anti-galling characteristic for better operating threads.0 0.33. Si 1.50 15.00 . 0. except by work hardened.60 Max.020 . P .00 Max 12 .0 .50 Balance .030 Max.0 119 .0 .00 .11. 1.4. Monel Alloy 400 ASTM B164 (N0400) Non hardened alloy.00 3.10.0 Mo 2. .024 Max.0 3.00 Max.03 Balance 3. Cast Cobalt ASME-SFA–5.0 .5 . Grade CA-15 Material used for 13 CR castings.0 This wrought material is precipitation hardened and possesses excellent corrosion resistance.13 Hard facing materials.040 Max.17.35 Max.50 Max. 14. Nickel-Moly-Chromium ASTM B574.00 Si 1.5 Max.00 ASTM A-743. – Cobalt. .020 0.50 3.00 . C Mn P S Si 08 Max 1.5 .5. Grade M-25S Material used for Monel castings. Mn 1.00 . 0.0-21.07 Max Mn 1. high strength properties and hardness for internal valve components.00 Max 12. . Gr. 0.5.50 Max 27. that has high strength and toughness over a wide temperature range.00 0.030 Max.020 0.04 Max.5 3.030 1.0 27.0 . . C 0. C .14.16.50 Max .0-12.006 0.14.33.5 Cobalt Base and Nickel Base Hard Facing Materials ASME SFA 5.45 S-Monel ASTM A-494.5. 63. 11. P .0. C Mn P S Si Cr 0. C Mn P S Si Cr Ni 0.14.35 .50 3.00 .04 Max. Balance 2. 630 17-4 PH Provides corrosion resistance and high strength for stems in NACE applications.85 27. the cast equivalent to Stellite #6.35 1.00 2.14 . when used on seating surfaces of Gate. and discs.60 Max.0.7.00 1.00 Max.00 .50 . 1.0 Mo W Fe Others Co ASTM A351 Grade CF8M Material used for 18-8 castings.035 Max.00 .00 .00 .006 C Mn S Si Ni Fe Cu . Chromium and Tungsten Alloy – Nickel.50 Max 2.70.70. Globe.040 S Cr Ni Mo .060 Max.040 Max 1.00 Max 2.00 .4.13.25 Max.50 .00 10. C Mn Si P S Ni Fe Cu .0-3.0.31.3.03 Max..33.25 .50 Max. the cast equivalent to type 316 stainless steel.03 1. S . (PSI) Q– Liquid flow in gallons per minute.0007s) .5P1 DRY SATURATED STEAM W = 2./HR.6 Cv WHEN ▲ P  .0007S) 120 ( Flow coefficient for valves and fittings.5P1 ▲P Fluid Flow Nomenclature PRESSURE DROP Q 2 ▲P=S Cv Cv 2 ) W(1 + .113 ▲P= P1 W=
2 ( ) W ▲P= P1 W= 1.5P1

( ) ▲ P x P1 T1Sg ▲P= . P1 – Absolute inlet pressure.00195 T1Sg 2.5P1 q´m 2 W = 1. (LBS.) Cv ▲ P x P1 .113 Cv – Cv P1 Sg T1 (1 + . s– Number of degrees of superheat for steam in °F. (SCFM) S– Specific gravity of flowing liquid relative to water at 60°F. (°R) W– Steam or vapor flow rate in pounds per hour.97 Cv ( ) ▲ P x P1 .7 psia and 60°F.82 Cv P1 SUPERHEATED STEAM WHEN ▲ P
. (GPM) q´m – Rate of gas flow in cubic feet per minute at standard conditions. (PSIA) ▲P– Pressure drop in pounds per square inch.82 Cv P1 (1 + .5P1

Q = Cv LIQUID q´m = 22.0007S) WHEN ▲ P  .Flow Control Division Vogt Valves Flow Data Utilizing Cv Factors FORMULAS FLOW RATE TYPE FLOW GAS WHEN ▲ P
. 14.5P1 S 13. T1 – Absolute inlet temperature in degrees Rankine. (PSIA) P2 – Absolute outlet pressure. Sg – Specific gravity of gas relative to air.9 P1Cv q´m = WHEN ▲ P
.97 Cv WHEN ▲ P  . 00123S) 121 ( 2 ) W(1 + 0.5P1 Q = .00274 P1 11. (KGS. ( ) W Q– Liquid flow in cubic meters per hour. q´ – H Rate of gas flow in cubic meters per hour at standard conditions. 1. Sg – Specific gravity of gas relative to air.53 Cv WHEN ▲ P  .71 Cv x P1 (1 + 0. T1 – Absolute inlet temperature in degrees Kelvin. S– Specific gravity of flowing liquid relative to water at 16°C. (BAR) P2 – Absolute outlet pressure.865Cv q´ = 414.2 P1Cv

Fluid Flow Nomenclature PRESSURE DROP W = 11./HR.) 2 Cv P1 Cv – Cv Sg T1 ▲ P x P1 (1 + 0.00123s) Cv Vogt Valves .5P1 DRY SATURATED STEAM WHEN ▲ P
.00262 ▲P= q´ 2 H Cv ( ) Flow coefficient for valves and fittings. s– Number of degrees of superheat for steam in °C.97 Cv H q´m = WHEN ▲ P  .6°C.81x10-6 T1Sg P1 ▲ P x P1 .5P1 S 19.01 BAR @ 15.5P1 ▲ P = 1. (BAR) ▲ P – Pressure drop in bars.00123S) WHEN ▲ P  .34S 2 Q ▲ P x P1 255.5P1 W = 19.5P1

▲P ▲P= 0.1 Cv T1Sg W=
W= ( ) ▲P= 5.Flow Control Division Flow Data Utilizing Cv Factors (Metric Version) FORMULAS FLOW RATE TYPE FLOW LIQUID GAS WHEN ▲ P
. P1 – Absolute inlet pressure.97 Cv P1 SUPERHEATED STEAM WHEN ▲ P
. (°K) W– Steam or vapor flow rate in kilograms per hour. 58431T FF 573. 13373. 12501. 42211MTG. 12321. 2811. 483. 122 . 59851. 66793 Z 2510. 9871T. 15493. 373. 2821. CT. 2801. 718. 363R. 12111. TT-12141 NN 15593. ST15801. 66733. 2522 Z-R R2510. 43111MMP. 373R. B701. ST-12141. B718. 483B. 82718 GG 9091. 363. 15701. B1551 S 1971 TT 810. 1522 Y 66723. 493B. R2522 AA 1331T. CT-2831. 2511. 32111. (3) A valve of same dimensional design but made from different pressure boundary material (body & bonnet) will have the same Cv factor as its A105 equivalent above. 12401. 1511. 353R. BT. 12161. SW-43211HF2. TT-2831 F CT-2901. 851. 11403 D 2801B E CT-2801. 16111. ST-2831. 10403 KK 13701 N SW-23141HF4. 22493CL.12501C K 473B. 583. 9841T CC 9821T.Flow Control Division Vogt Valves Cv Factor Matrix Valve Matrix A Typical Series Number (See Notes) 353. 12421. 22493MT. ST-12111 G 1033. 593. TT. 13111R C 11103. 801. (2) For different trim configurations. 15821 V 1003. 11683 H 66703. 12141B L 22141CL. 15373. 12181. 493. R2511. 701. trimmed series listed above. 822 T 22461 NOTE: (1) For SW or TSW Series. 12401C. use CV factor for corresponding 13 Cr. 66713 J 473. 1043. 10683 W 15443 X 1510. 1871T. use CV factor for corresponding threaded series listed above. 43241MTP LL 54853. 59951 B 13111. 11603. 2831. 22141MT. 15801. 54863 P 13141 MM S74. 22141F8M. 12521. 42241HF2 M Valve Matrix Typical Series Number (See Notes) U 15141. TT-2801. B9091 HH SWB-43721HF2 JJ 4835 10103. 701ZL. ST-2801. 32701. S701 Q CT-12141. 811. 1023. 15111. 12111R. 12141. 35111. 3991T BB 2891T. 43241MMP. 10603. B15701 R 12443 SS 1551. Flow Control Division Vogt Valves Cv Factors 1/4 8 3/8 10 A 2.6 3.9 9.6 9.7 20.3 80.5 B – – 9.6 28.7 46.5 80.5 109.6 181.0 C – – 9.6 28.7 46.5 80.5 109.6 181.0 242.3 322.7 D – – 9.6 9.7 20.3 – 109.6 117.6 – E – – 6.5 9.0 27.7 – 78.0 – F – – 9.6 9.7 20.3 – 78.0 – G – – 11.8 28.7 32.0 H – – 5.0 17.5 16.1 – J 1.3 2.0 2.4 4.3 7.3 K – – 2.2 5.7 5.2 L .7 1.7 1.7 3.1 M – – 3.4 Size NPS 1/2 15 3/4 20 1 25 1 1/4 1 1/2 32 40 2 50 91.6 117.6 2 1/2 65 4 100 NPS 1/4 8 3/8 10 1/2 15 3/4 20 1 25 1 1/4 1 1/2 32 40 2 50 2 1/2 65 3 80 4 100 V – – 3.6 6.0 10.2 15.1 24.2 39.8 – – – W – – 1.46 2.38 4.54 – 11.5 13.0 – – – – X** – – 6.0 4.0 9.3 – 57.8 48.9 – – – – – Y*** – – 1.2 4.3 5.8 – 17.6 19.3 – – – – – – Z*** – – 1.8 4.3 9.4 – 32.7 49.4 – – – – – – Z-R*** – – 1.5 3.9 7.9 – 29.3 39.8 – – – – – – AA 1.4 1.3 2.9 3.8 8.1 15.3 18.4 25.5 – – – 109.6 100.2 – – – BB 1.1 1.7 2.6 4.5 11.9 19.0 25.0 49.0 – – – 14.2 20.4 23.1 – – – CC .64 1.4 1.8 3.5 5.8 7.6 11.7 17.7 – – – – 21.1 20.5 – – – FF .9 1.5 2.1 3.2 5.8 13.3 18.3 25.3 – – – 5.9 13.7 18.4 22.5 – – – GG 1.5 2.0 3.6 6.7 11.8 20.2 26.1 43.3 – – – 7.3 11.9 15.6 28.2 46.9 – 85.1 – HH – – .7 5.9 11.8 – 22.6 32.6 – – – – 203.9 230.0 Size – 83.2 109.6 181.0 174 3 80 – N – – .7 5.9 13.7 – 21.0 34.0 – – – JJ – – 3.3 4.4 17.0 28.2 43.0 63.0 – – – P .9 2.5 3.0 6.8 14.5 17.2 24.4 37.6 – – – KK .9 1.5 3.2 6.9 16.0 18.3 25.5 36.9 – – – Q – – 2.4 4.3 7.3 – 20.4 – – – – LL – – 8.7 15.1 30.5 29.1 37.7 45.3 – – – R – – 1.46 2.38 4.54 – 9.65 14.6 – – – MM – – 9.2 6.8 22.0 – 54.6 81.9 – – – S 1.1 2.1 2.6 4.5 11.9 21.0 31.4 52.0 – – – NN – – 3.2 3.3 6.3 13.3 11.0 19.6 – – – T .56 .55 .68 .99 1.5 – – – – – – SS 1.2 1.3 2.1 4.1 7.3 10.5 17.6 23.3 – – – – – 3.1 3.3 5.9 – 13.8 21.4 – – – TT – – 4.5 9.1 21.3 – 70.0 79.1 – – – U** These Cv factors have been established by testing valves using Schedule 40 pipe except as noted. ** Sch. 160 used for testing valve. ***Sch. XXH used for testing valve. 123 Flow Control Division Fitting and Union Section – Pages 124-132 Vogt Valves VOGT’S ASME B16.11 A105 FITTINGS do not have a Pressure/Temperature Table. Consistent with the ASME B16.11-1996 e l b a l i a v A r e g n o L o N method of pressure/temperature application of fittings, Vogt A105 fittings have a pressure/temperature retaining capability equal to A106B or A106C connecting pipe schedules (see chart). Plugs and bushings are not identified by class designation. They may be used for ratings Class 6000 and lower. ns ac Fittings are manufactured under a t ou traceability system in order that material b sA rp Ma io Un tU certification can be provided when required. c nta Co Class Designations: 2000, 3000, 6000 Threaded or Socket Weld Pipe(1) Used for Rating Basis Class Designation of Fitting Type of Fitting Schedule No. Wall Designation 2000 3000 6000 Threaded Threaded Threaded 80 160 – XS – XXS 3000 6000 9000 Socket-Welding Socket-Welding Socket-Welding 80 160 – XS – XXS (1) This table is not intended to restrict the use of pipe of thinner or thicker wall with fittings. Pipe actually used may be thinner or thicker in nominal wall than that shown. When thinner pipe is used, its strength may govern the rating. When thicker pipe is used (e.g., for mechanical strength), the strength of the fitting governs the rating. 124 Dimensions are in inches and millimeters. Dimensions are subject to change without notice. Order by Size and Series Number. Flow Control Division Vogt Valves Forged Steel Strainer & Union Ells Style 3000 STRAINERS & UNION ELLS STYLE 3000 – 2271 HORIZONTAL & VERTICAL SCREW BONNET/SCREEN A105 Body/Bonnet 3000 PSI @ 100°F (206.9 BAR @ 38°C) SERIES NUMBER Threaded Socket Weld 2271 SW2271 Screen: 316* Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Dimensions "Y" Type Strainer NPS DN Size Size 3/8 DN 10 1/2 DN 15 3/4 DN 20 1 DN 25 1-1/2 DN 40 2 DN 50 A-End-to-End Cv Factor – B-Center-to-Bonnet End 6 14 C-Bead Diameter 14 Weight 40 40 3/8 10 2.50 64 2.31 59 1.50 38 3.78 1.7 1/2 15 3.00 76 2.75 70 1.75 44 2.24 1.0 3/4 20 3.50 89 3.19 81 2.00 51 3.80 1.7 1 25 4.00 102 3.56 90 2.38 60 5.10 2.3 1-1/4 32 4.50 114 4.00 102 2.69 68 6.88 3.1 1-1/2 40 6.0 152 5.25 133 3.56 90 16.2 7.4 2 50 7.50 191 6.19 157 4.31 109 28.4 12.9 – 6 14 14 – 40 40 Cv Factor * Strainers are furnished with 40 mesh, 31 gauge stainless steel screen. THREADED MALE & FEMALE Bold face numerals are in inches and pounds. Blue numerals are in millimeters and kilograms. Dimensions Size NPS DN 1/4 8 1.12 28 2.25 57 2.75 70 .94 .43 .91 .41 3/8 10 1.12 28 2.25 57 2.75 70 .84 .38 .78 .35 1/2 15 1.31 33 2.81 71 3.00 76 1.30 .59 1.63 .74 3/4 20 1.50 38 3.06 78 3.44 87 1.90 .86 1.90 .86 1 25 1.75 44 3.50 89 4.00 102 3.00 1.36 2.94 1.3 e l b a l i a v A r e g n No Lo A B THREADED FEMALE & FEMALE Style 2000 C A105 Material 2000 PSI @ 100°F (137.9 BAR @ 38°C) SERIES NUMBER Threaded Male & Female Union Ells 5061 SERIES NUMBER Threaded Female & Female Union Ells 6281 Weight-Series 5061 Weight-Series 6281 Refer to pages 116-120 for full materials description. 125 1-1/4 32 2.00 51 3.81 97 4.25 108 3.88 1.76 3.88 1.8 1-1/2 40 2.38 60 4.38 111 4.88 124 6.63 3.01 6.50 3.0 2 50 2.50 64 4.69 119 5.06 129 8.13 3.69 7.94 3.6 Head Flush Square Hd. 3000 6000 3000 3000 6000 6000 1/2 25 25 25 10 30 30 – 10 10 * 20 10 20 10 50 45 25 25 50 20 10 25 25 20 20 3/4 30 20 25 15 25 25 * 20 20 * 25 10 25 10 50 50 25 25 20 10 10 20 20 15 15 1 20 10 20 15 25 25 * 20 20 * 25 5 20 10 30 25 40 40 20 10 10 15 15 10 10 11/4 10 15 15 10 15 15 * 5 10 * 15 10 10 15 20 15 10 15 10 5 10 10 10 15 15 11/2 20 10 20 10 10 10 * 5 10 * 20 15 15 5 30 25 15 15 15 15 15 15 15 5 5 2 15 10 10 5 10 10 – 5 5 – 10 i 5 5 15 15 15 15 5 15 10 5 5 * * . Head Round Hd.Flow Control Division Vogt Valves ReadyPAK Fittings Number Of Fittings Per Carton 90° ELLS TEES 45° ELLS CROSSES STREET ELLS 45° LATERALS COUPLINGS *Not Prepackaged Series Pressure 1/8 259 2000 – 229 3000 25 1299 6000 25 SW 229 3000 25 SW 1299 6000 – 273 2000 – 243 3000 15 1399 6000 20 SW 243 3000 15 SW 1399 6000 – 1280 2000 – 2001 3000 25 2024 6000 10 SW 2001 3000 25 SW 2024 6000 – 1189 2000 – 1899 3000 15 2199 6000 15 SW 1899 3000 * SW 2199 6000 – 1800 3000 20 1260 6000 10 4823 3000 – SW 4823 3000 – 2324 3000 25 2350 6000 20 SW 2324 3000 25 SW 2350 6000 – 2450 3000 – SW 2450 3000 – 1/4 25 25 15 25 – 15 20 10 15 – 25 15 10 25 – 15 15 10 10 – 20 10 – – 20 10 20 – * * 3/8 15 15 25 15 – 10 10 10 10 – 15 10 10 15 – 15 10 10 10 – 10 15 – – 25 10 10 – 25 10 1/2 15 25 20 15 25 25 25 20 25 25 20 25 15 20 25 20 15 10 20 15 15 20 10 10 25 20 25 25 25 25 3/4 25 20 15 25 20 25 20 10 25 20 10 15 10 10 15 15 10 10 15 10 20 20 10 10 20 25 25 25 20 25 1 1-1/4 1-1/2 20 20 15 20 15 5 10 5 5 20 20 15 20 10 5 20 15 10 10 10 5 10 5 5 20 15 10 10 10 5 15 10 15 10 10 10 10 5 5 20 10 15 10 5 10 10 5 5 5 5 5 10 5 5 10 5 5 5 5 5 25 10 5 10 5 5 10 5 5 10 5 5 25 10 15 10 10 5 25 25 10 15 10 10 25 10 10 25 25 10 2 10 5 * 10 * 10 5 * 10 * 10 5 * 10 * 5 5 * 5 * 10 – * * 10 * 10 5 5 10 Series 2090 2110 SW 2090 SW 2110 1211 SW 1211 SWT 1211 1160 SW 1160 SWT 1160 4200 4001 SW 4200 SW 4001 2400 2370 2560 2580 2130 SW 503 SW 623 1931 1951 1961 SW 1961 Pressure 3000 6000 3000 6000 3000 3000 3000 6000 6000 6000 3000 6000 3000 6000 1/8 1/4 3/8 50 40 25 ~ 20 15 25 20 15 – – – – 15 25 – 15 25 – – – * 10 10 * 10 10 – – – 50 25 20 20 10 10 * 25 20 – – – – 50 50 – 100 50 100 50 50 100 50 50 50 50 20 – – 20 – – – 10 20 25 – 20 25 – * * – – – e l b a l i a v A r e g n o L o N HALF COUPLINGS WELD COUPLINGS CAPS BUSHINGS PLUGS INSERTS UNIONS —Not Manufactured 126 Hex. Hex. 9 2.82 .3 4.16 .9 13.82 3.08 1.35 .6 10.3 3.6 6.81 .83 2.12 .6 10.95 1.70 3.51 .01 .05 1.69 .7 10.05 .55 .39 .9 5.43 .25 .44 1.56 2.51 .52 1.16 .0 23.29 .1 9.33 2.10 .29 1.99 1.88 6.36 3.77 3.59 .20 1.43 2.52 .08 – – – – – – .6 9.99 2.18 .39 .7 4.33 3.34 .8 6.0 5.03 .5 3.24 .6 1.49 1.94 3.73 1.03 1.3 5.47 1.73 1.8 – – – – – – – – – – – – – – – – 39.33 5.6 3.54 .15 .9 2.65 2.1 5.34 .86 .68 .71 1.56 4.08 1.76 – – .58 1.82 .58 1.57 .3 12.9 – – – – 4 100 – – 28.25 1.02 – – – – .63 2.5 3.0 4.54 .24 .70 .6 14.8 6.64 1.36 1.50 .2 – – – – 4.09 .06 .29 1.8 1.88 1.6 7.10 .50 2.3 2.1 7.85 1.2 6.20 1.12 .39 3.12 .07 .11 .85 .6 14.08 .2 6.7 18.1 8.4 1.58 .9 4.17 .9 21.39 .8 7.44 .4 12.17 .9 2.4 8.7 11.79 .47 .09 1/4 8 .5 4.60 1.40 2.24 1.81 2.23 .4 14.15 .38 1.9 9.24 .58 .00 .08 .47 3/4 20 2.48 .1 1.99 1.04 .41 .39 .Flow Control Division Vogt Valves Forged Carbon Steel Fitting and Union Weights Series Number 229 SW 229 243 SW 243 259 273 1160 SW 1160 1189 1211 SW 1211 1260 1280 1299 SW 1299 1399 SW 1399 1800 1899 SW 1899 1931 SW 1931 1951 SW 1951 1961 SW 1961 2001 SW 2001 1/8 6 .39 .05 1.18 .35 .89 1.02 .89 .12 .3 2.10 .36 .56 1 1/2 40 5.50 .9 6.4 23.06 .02 .9 2.79 .07 .5 4.20 1.14 – – .04 .0 .30 .6 10.75 .50 .2 1.15 .18 .6 8.63 .8 13.2 1.8 27.04 1.53 .27 .41 .86 .10 1.45 2.77 .18 – – .0 12.69 .74 1 25 2.17 .0 17.72 .50 2.54 1.24 .14 – – .55 2.64 1.03 .41 .03 .6 e l b a l i a v A r e g n o L o N *Bushing and Reducing Coupling Weights vary according to reduction.33 2.9 – – 10.8 4.90 3.20 2.27 .13 .24 .93 3.18 – – .27 – – .4 3.53 .5 4.54 1.39 1.39 – – .0 2.06 2.5 3.21 2.24 .26 2.8 6.57 .31 .41 2.78 1.32 .57 .14 .7 17.93 1.14 .43 .1 18.60 3.93 .42 .3 21.1 3.57 .5 4 100 36.10 .53 .30 1.9 12.31 1.56 2.11 .05 .14 .63 .0 – – 50.0 – – 4.23 1.90 .5 6.0 7.7 43.1 2.66 3.7 4.02 2.6 28.21 .22 – – .85 .43 .73 2. 2110 SW 2110 2130 2199 SW 2199 2324 SW 2324 2350 SW 2350 2370* 2400* 2450* SW 2450* 2560 2580 2670* SW 2670* 4001 SW 4001 4200 SW 4200 4823 SW 4823 Bold face numerals are in inches and pounds.11 .03 .11 – – .4 1.50 .0 10.94 – – 2.0 3 80 19.0 2.5 7.70 .7 – – – – 39.58 1.42 .60 3.0 13.13 .8 8.18 .10 2.49 1.19 .65 2.11 .9 20.36 .01 1.0 12.74 1.94 .0 6.03 .97 .60 .54 .90 1.70 2 50 6.1 3.03 .77 .1 2.84 .31 .4 7.84 4.23 .1 4.20 3/4 20 1.63 .27 .2 .53 .06 .2 8.7 3.14 1.05 .50 1.34 .34 .74 .05 .33 .58 .50 3.15 .38 .1 14.9 – – 13.86 .16 1.85 2.0 6.26 .1 2.5 12.8 10.1 9.53 2.98 .7 4.05 .78 .4 2 1/2 65 15.21 2.55 .5 3.52 .42 1.6 4.5 3.20 .90 2.71 1.39 3.07 .15 .34 .41 .09 .53 .86 2.92 1.85 .0 1.11 .0 .53 – – .68 7.62 .33 – – .0 4.58 1.92 .04 .14 .4 3.55 .5 7.74 .38 .64 .56 .6 22.21 2.3 1.69 1.9 8.25 1.10 4.63 – – .90 1.3 8.15 .23 .4 5.94 .45 1.5 4.0 – – – – 12.24 .2 16.72 8.43 7.8 – – – – 13.34 .50 .12 .99 .1 4.7 10.01 .57 .18 1.90 .86 2.8 9.60 3.74 1.05 – – .18 .3 3.7 4.94 4.32 – – .32 .24 .40 .2 1.34 1.40 .23 .40 2.87 4.88 1.27 .08 .8 2.32 .6 6.14 – – .47 .39 .8 4.33 .81 1.73 .60 1.6 12.70 .25 .90 2.10 .51 1.3 8.12 – – – – .0 .0 3.18 .2 12.25 1.88 .6 1.30 .53 1.81 3.2 9.27 .18 .09 – – .6 10.15 .59 .7 6.90 .64 .22 .30 .78 1.48 .50 .1 5.19 2.06 .01 .90 .34 .1 14.69 .45 2.07 .06 .14 .13 2.06 .48 1.27 .04 – – .00 .03 .0 2.63 .07 .40 .2 11.28 .71 11.21 .85 .70 .46 .35 .26 .28 1.93 1.2 19.0 3.16 .8 21.28 1.1 2.1 6.42 1.46 3.07 .46 79 .94 .15 – – .25 2.55 .28 .0 5.02 1.23 .10 .6 1.0 4.31 .4 9.5 5.03 .25 .8 15.07 3/8 10 .0 12.02 .23 1.8 5.8 – – 7.38 1.13 .70 .09 1/2 15 .18 .83 .08 .0 .12 .19 .11 1.51 .19 .64 3.10 2.87 .64 .54 1.43 .19 .45 2.07 .13 .37 8.50 – – .52 .2 18.20 .65 3.00 1.83 3.92 .06 .71 1. .7 6.9 6.26 .20 .30 .2 5.33 1.86 .39 .69 .4 8.84 .20 .1 4.25 1 25 2.68 3.7 9.02 .86 1.43 .05 .91 7.27 .56 3.64 .10 .05 3.58 .19 4.41 .57 .6 5.10 .04 – – – – 3/8 10 .04 .26 .61 3.86 . 127 1 1/2 40 6.35 .01 .30 1.25 .7 26.43 1.06 .99 1.93 1.39 .1 .80 .68 1.88 .34 .08 .46 2.13 .35 .56 2.80 .58 3.4 4.05 – – – – 1/2 15 1.7 10.23 2.84 11.62 .94 1.50 1.00 .47 3.53 .21 2.48 .22 .0 9 – – 23.28 1.9 13.90 4.97 3.81 4.49 .19 .09 – – .10 .15 .89 2.42 .00 .9 8.15 .03 .63 1.1 25.6 2.31 .56 .4 4.10 .73 2.16 .63 .05 .62 .3 2.5 3.32 .15 .22 1.36 .13 1.29 – – .90 .21 .15 .45 750 34 – – 4.27 1.91 1.45 1.04 .5 24.39 .16 .63 1.05 .17 .26 1.60 1.65 .7 17.4 1.33 2.45 .02 .30 1.27 .36 1.05 .77 .10 .4 4.18 .65 1.01 2.89 1.05 .71 3.8 2.38 .0 5.12 .4 8.10 .07 .4 23.11 1.12 .57 .6 45.24 .11 .15 .64 1.18 .93 .48 .63 .24 .39 2.18 – – – – .01 .59 6.0 1.35 .2 4.1 2.04 .55 1.81 4.13 .16 .50 30 – – 7.87 3.3 – – – – 6.08 – – – – – – – – – – .31 .15 .9 1.14 .6 6.19 .69 1.26 3.2 3.92 .23 .04 . Weights listed are an approximated average.74 .58 .31 .2 10.74 1.1 1.07 .7 4.69 .8 15.20 .01 1.5 1.20 .44 .00 3.91 .05 .51 4.47 .5 1.09 – – .41 3.9 5.0 3.08 .0 2 1/2 65 15.20 .30 3.33 .40 3.29 .95 1.84 1.37 .54 2.85 1.02 .27 .32 .3 8.8 5.16 .88 1.59 3.33 .0 5.59 3.9 2.90 .31 2.6 12.28 .50 3.52 1.1 10.88 .63 .56 3.20 .45 .8 7.30 2.08 .46 1.53 4.8 1.5 10.22 .14 .20 .97 1.22 .06 2.0 10.75 .37 .90 2.40 2.05 .16 .2 16.30 .73 2.74 .37 .31 .11 2.01 .67 2.37 1 1/4 32 2.52 .2 .4 – – 6.13 1.24 .0 1.78 .16 .73 1.23 1.2 2.4 7.9 1.26 2.11 1.60 1.04 .2 2.25 2.45 .20 .63 1.1 5.23 1.15 .07 1.7 .23 .86 .15 .02 .3 1.51 .95 1.27 .41 – – .34 .06 .79 3.8 2.5 5.41 .49 .9 5.3 3 80 38.88 5.8 24.40 .1 22.4 25.52 1.19 .09 1.49 1.9 12.27 .3 5.44 – – 1.4 1.42 1.00 2.81 4.3 1.68 .05 .13 .0 1.20 .43 .2 6.9 33.1 1.45 2.58 1.60 .3 2.2 7.06 .8 2.2 1.31 .70 .54 6.1 .9 11.43 1.24 .02 – – – – 1/4 8 .19 .15 20.5 4.8 21.4 37.01 .15 .3 – – 4.54 .23 2.27 1.5 – – 30.13 .56 .7 – – – – – – – – – – – – 28.87 2.30 .18 .14 .14 .65 2.1 5.08 .9 4.13 .05 .10 .0 Series Number 2024 SW 2024 2090 SW 2090 1/8 6 .26 1.11 .8 7.54 9.20 1.40 .2 2.22 .27 .10 .82 1.3 2.7 21.70 .5 4.91 .9 4.72 .05 .42 .24 – – .66 .15 .6 3.05 .0 6.3 7.4 5.12 .06 .20 .86 .31 1.36 .8 6.27 .40 .03 4.38 1.60 .02 .1 28.23 3.05 .07 1.04 .95 1 1/4 32 4.28 1.6 11.79 1.40 .09 .32 .25 1.73 2.12 .11 .0 2.66 4.1 2 50 6.68 .62 2.12 .7 .4 4.92 1.34 .40 .0 4.70 .55 2.73 1.56 3.1 5.18 .34 .98 1.0 4.89 .4 – – – – Blue numerals are in millimeters and kilograms.12 1.7 9.34 8.23 .30 .25 .12 1.38 3.10 .0 3.6 2.2 2.5 2.32 2.6 3.01 .06 .71 1.8 5.3 11.04 – – .1 4.72 .79 .2 9.05 .4 8.07 .21 .02 .6 4.09 .06 .9 – – – – 12.19 . 11 128 WELD COUPLETS ASME B31.4 DN 6 .100 1/8 .3 DN 6 .4 DN 6 .3 DN 8 . 127.Flow Control Division Vogt Valves Forged Carbon Steel Fittings DESCRIPTION CLASS DESIGNATION SERIES NUMBER SIZE RANGE 2000 259 1/4 .2 DN 6 .80 2000 273 1/4 .4 DN 6 . Refer to Pages 116-120 for full materials description.3 DN 6 . 2560 Sizes 1/8 .100 ASME B16.100 ASME B16.50 SQ. .3 DN 6 .4.2 DN 6 .80 6000 2199 1/8 .80 1/2 .11 REDUCING COUPLINGS SIZE RANGE 4001 ASME B16.100 ROUND HEAD PLUGS Series No.80 1/4 .65 1800 ASME B16.11 TEES ASME B16.3 DN 8 .100 2670 1/4 .8(F) 6000 SERIES NUMBER SIZE RANGE 1211 1/4 .50 CROSSES ASME B16.80 6000 SERIES NUMBER HEX. HEAD BUSHINGS Series No.4 DN 6 . and the pressure piping code covering the particular installation.3 DN 6 .4 DN 6 .1 FIG.4 DN 8 . Pressure temperature ratings are dependent on the pipe schedule. 2580 Sizes 1/8 .100 6000 2350 1/8 .1-1/2 DN 6 .100 6000 2110 1/8 .11 6000 1299 1/8 .100 ASME B16. 3000 1/4 .4 DN 6 .11 45° ELLS ASME B16.100 3000 229 1/8 .100 3000 2324 1/8 .4 DN 6 .100 3000 243 1/8 .4 DN 8 .4 DN 8 .3 DN 6 .2 DN 15 .100 DESCRIPTION 3000 45° LATERALS 90° ELLS ASME B16.11 Notes concerning Pressure-Temperature Ratings For Fittings The ratings for forged steel fittings correspond to the pressure retaining capabilities of the connecting pipe.50 SWT 1211 1160 SWT 1160 1/8 .11 HEX.100 3000 2090 1/8 . HEAD PLUGS Series No. HEAD PLUGS Series No.4 DN 6 .11 6000 ASME B16.11 FLUSH BLUSHINGS Series No.11 ASME B16. service conditions.4 DN 6 . 2400 Sizes 1/4 .80 1/2 .2-1/2 DN 15 .40 4200 1/8 . 2370 Sizes 1/4 .4 DN 8 .4 DN 8 .4 DN 6 .100 6000 2000 1399 1189 PIPE CAPS COUPLINGS 3000 1899 1/8 .11 1/8 .2 DN 15 .50 4823 1260 1/8 .100 3000 2450 Carbon Steel material conforms to ASTM A105. 2130 Sizes 1/8 . Rating guidance is provided in ASME B16.11 which establishes procedures and tabulates a correlation of fitting pressure class designations with pipe schedule or wall designations.11 HALF COUPLINGS CLASS DESIGNATION e l b a l i a v A 1/8 .100 CLASS DESIGNATION 3000 6000 STREET ELLS 3000 r e g n o L o N 6000 2024 1/8 . See page 124 for extract.4 DN 6 .3 DN 8 .11 DESCRIPTION 1/2 .100 ASME B16.80 3000 2001 1/8 .4 DN 8 .3 DN 6 .100 ASME B16.80 2000 1280 1/4 . 75 95 4.88 22 1.94 49 2.50 38 1.62 67 1.19 30 2.31 8 1.19 46 56 2.91 23 1.69 43 1.12 79 1.50 33 1.50 13 1/2 15 1.75 121 5.25 32 1.31 33 1.75 19 .75 41 44 1.50 89 2.25 2.50 33 1.19 30 .00 76 3.50 64 1.31 1.00 25 1.88 22 1.00 76 4.69 43 1.75 18 19 2.50 114 B .12 28 1.44 37 1.31 109 – – – – – – F – – – – J – – 2.38 3.19 22 30 .25 159 3.06 52 2.19 5 .38 111 – – 5.00 51 2.62 41 1.25 32 1.06 2.62 16 .00 2.31 1.31 28 33 1.56 65 2.69 63 1.06 27 1.50 3.56 90 4.88 43 48 2.75 19 .62 92 4.75 19 .28 7 .81 71 2. head bushings of one-size reduction should not be used in services wherein they might be subject to harmful loads and forces other than internal pressures.88 111 124 2.00 25 1.12 54 2.50 38 .62 4.25 6 .31 33 .69 43 1.38 60 2.00 25 1.38 35 1.00 51 2.06 27 1.69 94 4.75 44 2.50 89 – – 4.50 38 1.19 30 1.75 44 2.62 16 1.75 19 F .88 22 1.50 13 .75 70 3.81 46 2.38 86 3.84 47 1.50 114 R .62 41 .75 19 .81 64 71 3.11 hex.00 25 .06 27 .00 127 2.00 2.50 13 .06 27 .00 44 51 2.50 2.25 2.88 48 .50 33 1.00 51 1.62 16 1.75 38 44 2.88 22 1.75 121 Q M .Flow Control Division Vogt Valves Threaded Fitting Dimensions Fitting Class NPS Designation DN CLASS 2000 CLASS 3000 1/8 6 1/4 8 3/8 10 1/2 15 3/4 20 1 25 1 1/4 1 1/2 32 40 2 50 2 1/2 65 3 80 3 1/2 90 4 100 A – – .00 25 1.31 33 – – – – – – 2.50 64 3.75 19 1.00 25 2. 1.62 16 .88 22 .12 79 3.22 47 56 2.62 41 .50 13 .38 60 2.88 22 1.31 33 1.12 28 1.50 64 3.88 1.00 25 1.50 190 – – – – – – K G .50 38 .00 76 3.88 22 .75 44 1.75 44 1.88 48 1.38 60 3.03 77 3.69 18 1.84 47 2.50 64 3.81 71 3.69 43 1.00 64 76 .50 64 2.34 85 1.56 14 3/4 20 1.50 64 3.25 57 – – – – – – 2.38 3.50 114 2.00 89 102 4.50 64 1.25 32 .88 62 73 2.69 1.94 24 1.38 33 35 1.50 64 3.69 .97 25 106 22 .00 25 1.50 64 3.12 54 2.88 22 1.25 108 2.81 21 e l b a l i a v A r e g n o L o N D E CLASS 6000 H R A PLUGS* AND BUSHINGS ASME B16.62 41 1.12 28 1.00 25 – – – – – – 1.00 76 4.62 16 .50 64 1.19 5 .81 21 2 2 1/2 50 65 3.38 35 1.56 40 3.25 92 108 2.50 64 3.50 38 1.50 38 1.25 32 .50 52 64 – – _ _ _ _ _ _ _ _ _ _ – – – – – – – – – – – – 3.25 6 .25 57 2.50 140 P L 1.69 33 43 1.75 146 3.12 79 3.75 44 1.94 75 1.88 43 .50 38 1.19 30 .22 2.00 51 2.62 92 4.94 49 1.44 2.00 25 3.12 54 5. They may be used for ratings up through pressure class 6000.50 38 1.75 44 .12 105 .75 44 – _ _ _ _ _ 3.00 51 .81 21 2.81 21 1.00 51 1.12 28 1.25 6 1.88 1.88 22 3.11 plugs and bushings are not identified by pressure class.62 1.88 22 1.62 16 2.81 21 .62 92 4.75 19 .69 18 1.75 146 C – – .31 84 – – – – – – – – N K .38 86 – – 4.00 76 3.50 38 1.75 70 – – 3.50 56 64 3.94 24 1.75 2.50 33 1.25 32 .25 57 1.31 33 1.50 33 38 .38 10 .50 114 4.50 38 1.62 16 .88 73 3.81 21 .12 28 .38 86 3.19 30 .75 86 95 4.00 152 7.38 10 .00 44 51 2.25 159 C .69 68 3.25 108 4.31 33 1.38 35 1.88 22 .38 2.94 24 1.50 38 1.75 44 2.25 108 4.56 14 2.62 57 66 2.69 18 .25 32 1.38 35 1.94 24 .62 16 .62 67 2.88 48 2.69 1.81 21 .12 1.00 2.38 11l 5.38 60 N – – .62 16 .12 28 1.19 5 .22 56 1.03 77 3.88 48 2.81 21 .00 76 4.25 6 .50 38 1.25 32 1.31 33 2.75 44 2.81 2.62 16 1 25 2.25 32 1.91 23 1.31 84 3.00 76 3.88 22 1.88 124 5.62 16 .25 6 .25 57 2.75 44 1.19 106 B – – .69 68 Fitting Class NPS Designation DN A B C 1/8 6 .25 32 1.38 60 2.38 35 1.50 11 13 .44 11 .12 79 3.75 19 1.62 16 .44 62 2.84 2.19 30 4 100 – – – – – – – _ _ _ _ _ – – – – – – 6.31 8 .38 35 – – – – – – – – 1/4 8 1.38 60 1.88 22 – – – – – – 1.81 21 .88 48 1.69 68 3.25 57 1.38 10 1.34 85 4.75 146 6.69 18 C .75 19 .88 48 2.44 11 .25 32 1.38 10 .38 35 1.38 10 2.12 28 1.75 19 .81 21 .31 33 .25 57 2.75 121 2.44 11 3/8 10 1.56 14 .00 51 2.38 10 .50 57 64 2.50 2.75 44 2.25 57 2.50 33 1.75 44 .56 14 .03 77 1.69 43 2.31 33 1.25 159 4.50 114 2. ASME B16.00 25 1.00 25 1.62 16 .25 159 3.00 51 2.81 46 .38 51 60 2.38 51 60 2.69 22 43 .38 35 – – – – – – 2.81 43 46 3.88 1.00 25 1.12 28 .31 33 .94 24 1.00 76 2.38 60 6.50 114 6.56 40 1.81 71 1.25 44 57 2.62 117 .75 18 19 1.25 82 – – – – – – – – L H .81 21 .50 64 – – – – A .94 24 1.50 114 6.56 14 .50 64 2.50 64 3.25 32 1.75 44 2.00 51 1.38 35 .75 19 1.75 44 2.50 64 – – – – – – – – M J 1.50 13 .75 70 3.31 33 1.75 2.19 81 4.50 13 .06 27 .12 28 – – – – – – 1.12 28 1.75 146 4.06 22 27 .12 79 – _ _ _ _ _ – – – – – – 5.00 51 1.50 1.19 30 .19 1.75 44 .19 30 B 1.69 43 – _ _ _ _ _ 2.69 43 .50 38 1.81 21 1.00 51 1.50 4.88 48 1.25 32 1.75 19 1 1/4 32 2.31 33 1.31 1.69 18 .38 4.25 6 1.50 64 2. D E F G H J K 129 1 1/2 40 2.19 106 5.75 19 – – – – – – 1.38 111 4.75 2.12 79 G D – – – – – – 1.31 33 1.84 21 .88 48 1.81 21 .56 14 .69 68 2.50 51 64 88.06 27 1.62 60 66 3.81 46 .44 11 .06 27 1.00 76 Q – – .69 .06 22 27 3 80 4.31 8 .53 90 .97 25 1.12 28 3 1/2 90 4.25 83 2.81 21 .62 16 .44 .97 25 1.62 4.31 8 1.31 33 1.00 25 1.19 106 4.12 79 – _ _ _ _ _ – – – – – – 5.38 10 .84 21 .38 111 – – 5.00 51 2.25 57 2.50 38 1.06 27 1.25 92 108 3.69 43 1.62 16 1.00 127 4.56 141 P – – 1.50 13 .75 64 70 2.31 135 – – – – – – E – – – – – – 1.38 35 .62 16 1.38 60 3.62 67 2.62 86 92 1.31 30 33 1.31 33 1. 100 6000 SW 4001 DESCRIPTION COUPLINGS ASME B16.100 3000 45° LATERALS Carbon Steel material conforms to ASTM A105.100 6000 SW 1299 ASME B16.1 FIG.11 45° ELLS 3000 SW 2001 1/8 .4 DN 15 . and the pressure piping code covering the particular installation. See page 124 for extract.100 DESCRIPTION REDUCER INSERTS MSS SP-79 6000 Notes concerning Pressure-Temperature Ratings For Fittings The ratings for forged steel fittings correspond to the pressure retaining capabilities of the connecting pipe.4 DN 15 .3 DN 8 .11 3000 SW 1899 1/8 .8(F) 6000 SW 1160 1/8 .4 DN 15 . service conditions.11 which establishes procedures and tabulates a correlation of fitting pressure class designations with pipe schedule or wall designations.50 SW 503* 3/8 X 1/4 DN 10 x 8 Thru 4X3 DN 100 x 80 3000 SW 623* 1/2 X 1/4 DN 15 x 8 Thru 2 1/2 X 2 DN 65 x50 1/4 . Rating guidance is provided in ASME B16.2 DN 15 .2 DN 15 .11 3000 CROSSES PIPE CAPS CLASS WELD COUPLETS ASME B16. Pressure temperature ratings are dependent on the pipe schedule. 127.100 6000 SW 2024 1/2 .80 SWT 1211 1/2 .100 6000 SW 2110 1/2 .4 DN 6 .50 ASME B16.11 3000 e l b a l i a v A 3000 SW 2324 1/8 .100 REDUCING COUPLINGS 6000 6000 ASME B16.100 6000 SW 2350 1/2 . Refer to Pages 116-120 for full materials description.4 DN 20 . *Dimensions for Reducer Inserts furnished on request.11 TEES 1/2 .4 DN 6 .100 3000 6000 ASME B16.100 SW 2199 1/2 .Flow Control Division Vogt Valves Forged Carbon Steel Fittings DESCRIPTION 90° ELLS CLASS DESIGNATION SERIES NUMBER SIZE RANGE 3000 SW 229 1/8 . CLASS DESIGNATION 1/2 .100 SW 2090 1/8 .11 ASME B16.50 ASME B31.80 SWT 1160 1/2 .100 130 SERIES NUMBER SIZE RANGE SW 1211 1/4 .4 DN 6 .4 DN 6 .4 DN 6 .4 DN 8 .2-1/2 DN 15 .3 DN 6 .11 1/2 .100 SW 4823 HALF COUPLINGS SW 2450 SW 2670 3/4 . .50 ASME B16.4 DN 6 .4.2 DN 15 .4 DN 15 .2 DN 15 .4 DN 6 .100 1/2 .2 DN 6 .100 r e g n o L o N SW 243 SW 1399 3000 1/8 .11 SERIES SIZE 3000 SW 4200 1/8 . 12 54 2.0 1.86 22 K – – – – L – – – – M .5 .62 41.25 108 5.5 1.00 102 4.7 1.6 2.16 29.88 48 W – – – – – – 1.9 1.50 12.1 1.0 1.75 70 3.855 21.07 52.6 1.12 28.5 .34 34.56 14.4 .81 20.75 19.38 35 1.09 28 1.5 1.25 57.2 3.1 N – – – – – – .06 26.0 .1 E .5 .7 3.38 35 1.7 G – – – – – – .69 17.69 17.1 .75 44.06 27 Q .50 64 2.06 27.5 .69 17.Flow Control Division Vogt Valves Socket Weld Fitting Dimensions Fitting Class Designation NPS DN 1/8 6 1/4 8 3/8 10 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 2-1/2 65 3 80 4 100 2.05 26.88 48 2.69 94 4.9 .88 22 1.07 52.7 .5 1.19 30 1.94 49.88 22.5 1.53 13.5 .9 1.50 64 2.5 W .25 32.88 22.7 1.25 6.62 92 4.50 64 2.25 159 .9 1.38 9.0 B .12 54 X – – .69 17.62 15.50 64 3.62 15.0 .38 9.4 1.5 .4 1.44 62.25 32 1.5 .9 1.97 75 3.50 64 3.88 22.6 1.0 1.25 57 2.555 14.75 19.8 2.4 1.545 115.8 1.7 .38 35.4 1.8 1.88 22.9 2.31 8.1 1.4 1.50 12.6 .5 .00 25.0 4.88 22.0 1.31 33 1.06 27 1.38 9.62 15.62 41.88 22 N .5 P 1.88 22.0 1.00 76 T 1.0 .03 77 3.50 38 1.906 3.1 .4 R .8 2.75 19 .4 1.19 30.47 62.5 1.38 9.49 12.675 42.44 11.1 .9 4.25 57 2.9 1.7 .9 2.0 .50 64 3.62 41.5 .8 .44 11.8 1.5 .31 33 1.62 41.9 2.50 64 3.6 .31 8.7 .0 1.9 89.0 F – – – – – – .35 85 4.1 .3 2.1 .50 64 3.75 44 2.00 76 3.7 .38 35 1.6 2.62 15.1 .0 2.5 3.7 3.7 .47 63 3.72 44 1.25 57 2.62 41.84 47 2.7 1.50 12.5 .7 .50 38 1.0 1.12 28 1.62 15.0 .05 26.12 28.12 28.81 20.406 61.25 57 2.72 94 4.36 9.7 .25 32 1.94 49.75 44 2.00 51 2.12 79 3.0 2.69 43 1.75 146 H – – – – – – 1.00 76 3.5 2.47 11.25 32 1.75 44.31 33 1.97 50 2.5 .62 15.3 1.31 33.75 19.88 73.0 2.56 14.5 3.50 88.0 .0 1.75 19.0 1.0 1.38 9.38 35.4 .5 .38 9.9 1.94 24.6 .7 .5 1.0 2.5 1.50 38 1.03 102.00 25.86 22 .27 6.62 15.2 B .38 35 1.62 15.50 64 3.38 35.5 1.38 9.62 15.1 .00 76 .0 1.19 81 4.50 38 1.00 25.81 46 2.0 .5 V – – – – – – .75 19.88 22.06 27 1. Blue numerals are in millimeters and kilograms.03 102 .69 43 1.62 15.1 D .50 38.69 18 .38 9.81 20.28 33 1.62 92 4.69 18 .7 .38 111 5.06 52.7 .88 73.25 6.38 9.7 .0 Q – – – – – – .00 25.06 26.50 63.9 .81 20.675 42.06 52 2.7 .38 35 1.31 109 5.25 57.25 32.5 1.56 141 X .44 62.50 12.38 111 5.22 56 2.12 79 C – – – – – – 1.19 30 1.88 22.7 1.420 10.50 12.88 48.50 12.2 C .6 D – – – – – – .88 124 6.75 19.88 22.5 .4 1.7 1.12 28.19 56 2.19 30 1.62 92 4.31 135 – – – – K – – – – – – – – – – – – – – – – – – – – – – – – – – 2.5 .50 12.56 14.0 1.75 19.9.12 79 1.535 739 89.62 15.00 25.69 17.00 51 2.50 12.50 114.91 23 1. 1.75 19.69 42.61 40.69 17.69 43 2.2 2.97 25 1.0 1.94 24 1.06 27 1.44 11.75 19.915 48.2 .5 A – – – – – – .00 76 3.5 – – – – G – – – – – – – – – – – – – – – – – – – – – – – – 1.25 32.7 .69 17.5 .44 11.47 37 1.62 41.00 51 2.7 .88 48 2.5 2.75 70 3.69 42.5 1.50 64 2.62 41.56 14.50 38 1.06 77.50 12.6 .4 1.62 41 1.7 .88 22.50 38 1.5 .50 63.50 12.00 25.62 15.31 8.88 22.50 12.1 2.91 23 .75 19.7 1.50 38 1.82 20.420 10.50 64 3.5 1.88 48 2.00 25.0 1.5 .00 152 750 190 – – – – L – – – – – – – – – – – – – – – – – – – – – – – – 1.0 .62 41.38 111 4.56 14.4 .62 15.1 .06 27 J .0 .47 114 – – 1.75 19.49 12.9 4.4 .81 71 3.5 .00 51 2.0 1.69 17.12 28.31 33 1.1 .06 27 1.0 .5 T – – 1.5 .5 F .50 114 1.50 63.4 U .38 9.065 27.94 23.00 25.19 30 U – – V CLASS 3000 r e g n o L o N Bold face numerals are in inches and pounds.25 108 5.19 30 1.44 11.00 76 P – – – – – – 1.0 .50 12.5 .50 140 M – – – – – – 1.4 1.88 48.7 .5 E – – – – – – .5 .3 2.50 12.0 .9 1.31 33 1.2 1.50 64 3.44 87.7 .12 28 1.35 60 2.00 25.62 66.56 14.81 20.906 3.5 .0 .38 9.28 33 1.97 50 2.8 2.81 20.0 .12 28.69 17.7 .06 27 1.00 25.56 14.62 41 1.7 .7 .50 12.38 9.12 28.8 .44 11.9 4.75 19.7 .25 159 .5 .1 1.75 44 1.7 .50 88.0 .5 .4 1.35 60 2.25 6.62 41.5 .75 70.06 26.00 127 6.56 14.690 17.56 14.0 H .47 37 1.7 4.00 25.75 70 3.0 .50 12.2 1.5 1.36 9.25 57 2.47 62.1 .00 76 .7 .7 R – – .00 25.62 66.35 85 3.5 .75 44 2.065 27.0 .69 42.406 61.1 .50 64 2.1 .69 17.1 .47 63 3.50 63.4 1.25 32.3 S .50 12.50 38 1.75 19.88 48 2.31 33 1.7 .50 12.12 28 1.62 15.62 15.38 9.5 .1 S – – .19 30 1.88 48 2.5 .0 .75 44 1.62 15.50 64 2.7 .84 47 2.1 2.3 1.330 33.38 9.38 35.72 44 1.2 .00 127 6.555 14.12 53.07 78 4.2 .50 89 4.9 1.75 19.88 22.61 40. Fitting Class Designation e l b a l i a v A CLASS 6000 131 .7 .75 70 3.38 111 5.75 44 1.50 12.0 .0 .50 38 1.0 1.50 12.8 1.00 25.75 44 2.1 .3 2.88 22.75 19.56 14.50 114 6.94 24.69 17.1 1.62 15.12 28.0 2.75 19.915 48.535 73.88 22 1.50 38.07 78.0 .81 46 2.7 .25 159 NPS DN 1/8 6 1/4 8 3/8 10 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 2-1/2 65 3 80 4 100 A .7 .2 3.4 .38 35 1.50 12.5 1.25 32 1.03 77 3.5 .62 92 4.855 21.5 1.5 2.5 1.82 20.7 .330 33.38 35.19 30.5 .50 12.4 1.94 23.75 19.5 .0 1.00 101.69 43 1.690 17.0 .31 33.7 .25 32 1.25 32.06 27.44 11.50 38 1.7 .75 19.7 .00 76 3.1 .16 106 J – – – – – – 1.34 85 4.31 33 1.2 1.8 4.25 65 .44 11.1 1.0 .22 56 2.56 14.0 .545 115. 25 3.20 — ta 61 70 83 92 109 132 on SW 1961 1/4 .7 375.06 3. PRESSURE-TEMPERATURE RATINGS FOR THREADED AND SOCKET WELD END UNIONS PRESSURE IN PSIG METRIC: PRESSURE IN BARS SERVICE TEMP.3 DN 6 .81 3.41 2.75 3.93 2. (°C) CLASS 3000 CLASS 6000 -29 to 38 50 100 150 200 250 300 350 371 206.09 — M 56ut 63 71 78 86 104 — — — — C “B” dimension is across corners of nut.44 2.03 4.63 1.62 4.81 1.1 299.39 4.15 40 40 48 49 61 70 o83 ns 92 109 133 156 ni A SOCKET WELD ENDS 1/8 6 e l b a l i a v A r e g n o L o N 1951 1/4 .0 177.Flow Control Division Vogt Valves Forged Steel Unions DESCRIPTION SERVICE DESIGNATION SERIES NO.59 1.81 1.41 2.9 157.01 3.80 1931 PNS DN A CLASS 6000* CLASS 3000 MSS SP-83 1961 1/4 .39 4.06 3.9 297.50 THREADED ENDS UNION DIMENSIONS — — o Ab s U — ct— 2.2 DN 8 .9 366.01 3.75 3.38 4.47 arp 2.6 413.50 B 1/4 8 3/8 10 1/2 15 3/4 20 1 25 1-1/4 1-1/2 32 40 2 50 2-1/2 65 3 80 1.38 4.8 338. SIZE RANGE CLASS 3000 MSS SP-83 1/8 .62 4.8 405.28 5.2 Bold face numerals are in inches.28 5.41 2.9 148.4 168.9 202.81 3.97 2. Blue numerals are in millimeters.63 1.0 314.03 4.29 41 41 46 49 57 62 71 76 86 102 109 CLASS 6000* 1.22 6.62 4.0 149.2 8 .88 1.91 2.88 1.28 5.28 5.80 SW 1951 1/4 .24 2.15 40 40 48 49 61 70 83 92 109 133 156 A — 1.81 1. 132 .62 4.25 3.91 2.81 3.47 2.22 2.81 3.59 1.2 DN 8 .63 1.29 41 41 46 49 57 62 71 76 86 102 109 B 1. Class 6000 unions are designed proportionately to Class 3000 unions which meet the provisions of MSS SP-83. (°F) CLASS 3000 CLASS 6000 -20 to 100 200 300 400 500 600 650 700 750 3000 2735 2655 2565 2425 2220 2180 2155 – 6000 5470 5310 5130 4850 4440 4360 4310 – SERVICE TEMP.50 SW 1931 1/8 .44 2.25 3. *Note: There are no current industry standards applicable to Class 6000 unions.24 2.59 1.0 354.93 2.22 6.91 2.88 1.22 2.50 B cU a 2.63 1.2 DN 8 .75 3.09 — 46 50 56 63 71 78 86 104 — B — 1.25 3.75 3.3 DN 6 .59 1.20 — 48 48 61 70 83 92 109 132 — A 1.9 183.9 187.41 2. NEGLIGENCE OR OTHERWISE. Upon request by Seller. THE REMEDY SET FORTH IN THIS LIMITED WARRANTY IS EXPRESSLY AGREED TO BE THE SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. (iv) manufactured. or reasonably should have. with its own representatives. to the extent same is assignable. and shall be subject to the following: (a) This warranty shall not apply to Goods which have been (i) repaired or altered by any Person other than the Seller. In no event shall Seller be required to repair. (ii) subjected to unreasonable or improper use or use beyond rated conditions. incurred by Seller as a result of any third party claim relating to the purchase . negligence or accident. Buyer shall. improper storage. after Buyer (or any other Person using the Goods) has. (b) This warranty shall not be effective unless Seller receives a written claim within thirty (30) days after discovery of any defect with respect to which a claim is made. FITNESS FOR A PARTICULAR PURPOSE AND CONFORMITY TO MODELS OR SAMPLES. STRICT LIABILITY. (e) Seller’s liability for any breach of warranty shall be limited either to (i) repair or replacement (whichever Seller shall elect) at Seller’s Plant of any Goods determined by Seller to be defective. sale or use of. or (ii) payment of an amount equal to the invoiced cost to Buyer of the part or material which is defective. or (v) improperly installed by any Person (including Buyer) other than Seller. IMPLIED OR STATUTORY. the nature and extent of any claimed defect prior to return of the Goods to Seller. EXPRESS. 133 . shall expire on the last day of such one (1) year period. the Goods covered by this Agreement.O. as Seller may elect. at its own risk and expense.Flow Control Division Limited Warranty Vogt Valves Seller warrants that the Goods shall be free from defects in materials manufactured by Seller and in Seller’s workmanship for a period of one (1) year following shipment (the “Warranty Period”). (c) Seller shall have the right (but not the obligation) to verify. including reasonable attorney’s fees. This limited warranty shall apply only in favor of Buyer. (f) THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES (EXCEPT OF TITLE). knowledge of any defect. IS HEREBY EXCLUDED. (d) Buyer covenants to inform all subsequent buyers to the Goods of the limitations on and exclusion of the warranties provided for herein. otherwise relating to. shipping or other costs incurred in connection with the reshipment of defective Goods to Seller or the reinstallation of such Goods after any repair or replacement. Seller’s Plant and shall be warranted for the remaining term of the original Warranty Period for such Goods. Any Goods that are repaired or replaced by Seller shall be re-delivered to Buyer F. INCLUDING WITHOUT LIMITATION ANY IMPLIED OR EXPRESS WARRANTIES OF MERCHANTABILITY. Buyer hereby indemnifies and agrees to hold Seller harmless from and against all losses costs and expenses. The Goods. ALL OTHER LIABILITY WHETHER IN CONTRACT OR TORT. any warranty Seller has received from the manufacture of such Goods). promptly return the Goods in question to Seller’s Plant.B. shall not be construed to be a “part” or “material” for the purpose of the immediately preceding sentence. fabricated or assembled by any Person other than Seller (Seller shall assign to Buyer. as a whole. (iii) damaged because of use of the Goods or the incorporation of the Goods into use of any Goods with other materials or equipment. replace or reimburse Buyer for more than the part or material that is found to defective and Seller’s liability shall in no event be greater than the invoiced price of the item and shall not include labor. SWE – Socket Weld End SWP – Steam Working Pressure T – Tee Thd. Oil and Gas (See CWP) WSP – Working Steam Pressure WWP – Working Water Pressure XS – Extra Strong Wall Thickness XXS – Double Extra Strong Wall Thickness Y – Wye Valve. OS&Y – Outside Screw and Yoke OWG – Oil. or Sched. 127 Park Street N. Rising Stem LH – Left Hand MAV – Motor Actuated Valve mm – Millimeter MOV – See MAV MSS – Manufacturers Standardization Society of the Valve & Fitting Industry NACE – National Association of Corrosion Engineers (Formerly NACE International) NPS – Nominal Pipe Size NPT – National Standard Pipe Thread Taper NRS – Non Rising Stem OD – Outside Diameter One-Piece Stem – An inseparable Stem and Disc made from one piece of metal.. – Threaded TIR – Total Indicator Reading UB – Union Bonnet W – Water Wedge – Gate WOG – Water. Fitting or Strainer Yoke Bushing – Operating Stem Nut Yoke Nut – Stem Nut Refer to MSS-SP-96 for additional Abbreviations and Terms used in the Valve and Fitting Industry. Water & Gas (See CWP) PN – Pressure Nominal (Metric) Psi – Pounds per square inch Psia – Pounds per square inch absolute Psig – Pounds per square inch gage P-T – Pressure-Temperature Rc – Rockwell “C” RF – Raised Face RH – Right Hand RMS – Root Mean Square Roughness Height RS – Rising Stem RTJ – Ring-Type Joint 134 S – Steam SAE – Society of Automotive Engineers SC – Swing Check Valve Sch. VA 22180) . Vienna. ASME – American Society of Mechanical Engineers ASTM – American Society for Testing and Materials AWS – American Welding Society HF – Hard Faced HW – Handwheel BB – Bolted Bonnet BHN – Brinell Hardness Number Blind Flange – A Flange with no flow way bore.S. Inc. used to provide a pressure-tight closure of a flanged opening.Flow Control Division Vogt Valves Glossary of Abbreviations & Terms Used in the Valve and Fitting Industry AARH – Arithmetic Average Roughness Height AISI – American Iron and Steel Institute API – American Petroleum Institute ANSI – American National Standards Institute. Btu – British Thermal Unit BWE – Butt Weld Ends Kg – Kilograms km – Kilometers C or Cel – Celsius degrees Cl – Cast Iron Cl – Chlorine Institute CR 13 – 13% Chromium Stainless Steel CRES – Corrosion Resistant Steel Cv – The number of U. gallons per minute of water at 70°F which will flow through a valve at a pressure drop of one psi. CWP – Cold Working Pressure DN – Diameter Nominal (Metric) ELL – Elbow FAS – Free Alongside Steamer F or Fahr – Fahrenheit degrees F & D – Faced and Drilled FF – Flat Face FHF – Full Hard Faced FLG – Flanged FOB – Free on Board FTTG – Fitting G – Gas gpm – Gallon per Minute IBBM – Iron Body Bronze Mounted ID – Inside Diameter INT – Integral IPS – Iron Pipe Size ISRS – Inside Screw Rising Stem ISNRS – Inside Screw Non. – Schedule (Pipe Wall Thickness) SCFM – Standard Cubic Feet per Minute Screw Bonnet – Body and Bonnet Threaded Together SE – Screwed Ends Seal Weld – Threaded Joint Back Welded for Seal SS – Stainless Steel Stem Nut – Operating Nut Stuffing Box – Packing Chamber STD – Standard Wall Thickness Stop Check – A Check valve in which the closure member can be mechanically closed.E. (Manufacturers Standardization Society. Flow Control Division Standards in the Valve and Fitting Industry Codes and standards play an important role in the design and production of forged steel valves, fittings, and unions. These codes and standards cover material, product dimension, design, examination, inspection, testing procedure, pressure/temperature ratings, and safety. Material standards are developed by such organizations as the American Society for Testing and Materials (ASTM), the American Iron & Steel Institute (AISI), the Society of Automotive Engineers (SAE), and the National Association of Corrosion Engineers (NACE) . The American National Standards Institute, Inc. (ANSI), whose membership is composed of both user and producer groups, serves as the national coordinator for the majority of code and product standards related to the Valve and Fittings Industry. Product standards are also developed and issued by individual user and/or manufacturing agencies such as the American Society of Mechanical Engineers (ASME), American Petroleum Institute (API) and the Manufacturers’ Standardization Society (MSS). Procedural and safety standards are issued by ANSI, MSS and the American Society of Mechanical Engineers (ASME). Following is a partial list of codes and standards that have a direct bearing on the design and production of Vogt’s forged steel valves, fittings, and unions. The codes and standards are interrelated as the following descriptions project: ASME Boiler & Vessel Code Section I – Power Boilers Section ll – Material Specifications Section lll – Nuclear Power Plant Components Section V – Nondestructive Examination Section Vlll – Pressure Vessels Section IX – Welding and Brazing Qualifications The above Codes (Sections I, lll & Vlll) cover construction requirements for Boilers, Pressure Vessels, and Nuclear Components that require Authorized Inspection Agency involvement. Section I and Vlll Codes relate to the boiler and pressure vessel proper and not to external piping. Section lll Code includes rules for nuclear components including piping. Section II, V and IX Codes cover material, nondestructive examination and welding requirements, respectively, for ASME construction. ASME Codes for Pressure Piping ASME B31.1-95 – Power Piping Vogt Valves Valve Standards ASME B16.34 – Valves - Flanged, Threaded and Welding Ends API-600 – Steel Gate Valves, Flanged, and Buttwelding Ends API-602 – Compact Steel Gate Valves MSS-SP-99 – Instrument Valves MSS-SP-118 – Compact Steel Globe and Check Valves* The above are component (valve) standards used for construction of Vogt valves as noted in this catalog. Flanges, Fittings and Unions ASME B31.3-96 – Process Piping ASME B16.5 – Pipe Flanges and Flanged Fittings ASME B31.4 – Liquid Transportation Systems for Hydrocarbons, Liquid Petroleum Gas, Anhydrous Ammonia and Alcohols. ASME B16.11 – Forged Steel Fittings, Socket Weld and Threaded ASME B31.5-92 – Refrigeration Piping ASME B31.8-95 – Gas Transmission and Distribution Piping Systems MSS-SP-83 – Steel Pipe Unions, Socket Welding and Threaded Ends MSS-SP-79 – Socket Welding Reducer Inserts The above standards are recognized for the construction of flanges, fittings and Unions. ASME B31.9 – Building Services Piping Systems ASME B31.11 – Slurry Transportation Piping Systems The above are piping construction codes that include requirements for design, materials, fabrication, examination, testing, inspection and components. Valve, fitting, union and flange requirements used in these piping systems are normally referenced standards, as follows: 135 (* This standard practice (SP) is not currently referenced in Vogt’s VV-200 catalog but Vogt class 150, 300, 600, 800 and 1500 globe and check valves would normally meet the SP but they also meet the wall thickness requirements of API 602. Vogt Class 150, 300 & 600 globe and check valves meet the applicable requirements of a class 800 API602 valve, including the heavier wall thicknesses of API602.) Flow Control Division Standards in the Valve and Fitting Industry Valve, Fitting, Flange and Union Details ASME B1.20.1 – Pipe Threads, General Purpose ASME B16.10 – Face-to-Face and End-to-End Dimensions of Ferrous Valves ASME B16.20 – Ring Joint Gaskets and Grooves for Steel Pipe Flanges ASME B16.25 – Buttwelding Ends MSS-SP-6 – Standard Finishes for Contact Faces of Pipe Flanges and Connecting End Flanges of Valves MSS-SP-25 – Standard Marking System for Valves, Fittings, Flanges and Unions MSS-SP-45 – Bypass and Drain Connection Standard NACE Standard MR-01-75 – Sulfide Stress Cracking Resistant Metallic Material for Oil Field Equipment This standard is a recognized practice for selection of materials for construction of valves to be used in a sour environment. Such materials are recommended when sulfide stress cracking (SSC) is anticipated. Chlorine Institute PAMPHLET #6 – Piping Systems For Dry Chlorine This publication is intended to provide useful information concerning the construction of chlorine piping systems including valves. For detailed Material Standards used by Vogt valves, see page 118 and 119. The above standards are detailed dimensional, marking, finish and bypass valve and fittings instructions for use in the manufacture of valves, flanges and fittings. The product standards normally refer to these standards for detailed instructions. Vogt Valves ADDRESSES: American Iron & Steel Institute (AISI) 1133 15th Street, N.W. Washington, D.C. 20005-2701 American National Standards Institute (ANSI) 11 West 42nd Street New York, N.Y. 10036 American Petroleum Institute (API) 1220 L Street Northwest Washington, D.C. 20005 American Society of Mechanical Engineers (ASME) United Engineering Center 345 E. 47th Street New York, N.Y. 10017 American Society of Testing Materials (ASTM) 100 Barr Harbor Dr. West Conshohocken, PA 19428-2959 Manufacturers Standardization Society of the Valve & Fitting Industry, Inc. (MSS) 127 Park Street, N.E. Vienna, VA 22180 NACE International P.O. Box 218340 Houston, TX 77218–8340 Inspection and Testing MSS-SP-61 – Pressure Testing of Valves Society of Automotive Engineers (SAE) 400 Commonwealth Drive Warrendale, PA 15096 API-598 – Valve Inspection and Test The above highly recognized standards provide detailed instructions for inspection and testing of valves. The Chlorine Institute, Inc. 2001 L Street, NW Washington, D.C. 20036 136 Flow Control Division Care and Maintenance of Vogt Forged Steel Valves VALVE CARE BEFORE INSTALLATION Vogt valves are carefully made from selected materials to give long, trouble-free service when properly installed in applications for which they were designed. Proper care and maintenance in the field can contribute significantly to maximum performance. The care the valve receives between the time it is shipped by the manufacturer and installed in the piping system is important. During this period, the valve can be handled many times and can be kept in storage for long periods. Industrial valves are not delicate, but they are mechanical devices which should be treated as such and handled with care. Vogt always provides valves with appropriate end covers to protect the end connections and to prevent foreign material from entering the valve. In addition, small valves are shipped in sealed cartons while larger valves are usually palletized. If at all practical, keep the valves in the cartons or on the pallets with end covers in place until ready to be installed. Storing the valves off the ground and indoors is always preferable. When stored outside, valves should be off the ground and protected by a weatherproof cover. Prior to installation, the valves and nameplates should be checked for proper identification to be sure the valve is the proper type and of a suitable pressure class. Actuate the valve to check for possible damage from shipping and handling. Also, it is extremely important to inspect the interior of both the valve and the adjoining pipe for cleanliness. By far the major cause of seat leakage and seat damage is foreign material in the line. Also, inspect end connections to be sure that pipe threads and flange faces are free from scratches, nicks, or dents. ROUTINE INSPECTION AND MAINTENANCE Once the right valve is properly installed, field maintenance is of a generally routine nature and can be readily performed by the user. The critical areas of a valve include the stem threads and those locations where leakage will most likely occur—the stem packing, the bonnet joint, the seat and the end connections. It is desirable that a maintenance program be established which will include periodic inspection of the noted critical areas. Stem threads should be lubricated prior to installation and periodically as part of the regular inspection. A high pressure and temperature lubricant such as Dow Corning MolykoteTM G-n Paste should be used . The most common location of a noticeable leak is at the stem seal. Leakage at the stem can usually be stopped by adjusting the packing. If leakage cannot be stopped by packing adjustment, repacking is indicated. However, backseating the valve and attempting to repack under pressure is hazardous and is not recommended. Rather than attempting to repack under pressure, it is preferable to use the backseat to control the stem leakage until a shutdown provides safe repacking conditions. 137 Vogt Valves MAJOR FIELD REPAIR Maintenance involving rework or replacement of parts is considered major repair. When circumstances dictate field repair of Vogt valves, the following information is offered as an aid. It must be pointed out, however, that Vogt valves repaired in the field are no longer under “Product Warranty,” and in no event is Vogt liable for any incidental or consequential damages resulting from any cause whatsoever. There are no warranties of any kind whatsoever, express or implied, other than those stated in Vogt’s current Terms and Conditions. Preliminary Considerations for Valve Repair: 1. Use experienced, trained personnel. 2. Observe all standard safety precautions. 3. If possible, remove valve from line so that work can be done in a clean, well lighted area. 4. Use genuine Vogt replacement parts. 5. Use proper tools. 6. Pressure test valve before reinstalling. This is particularly essential on valves intended for critical service. 7. Remember that improper repairs can be hazardous. Repacking under pressure is hazardous and is not recommended. PACKING Vogt valves have well proportioned stuffing boxes filled with the best grade of packing available. If stem remains tight. & Y. be sure to have the right grade. Orders for replacement parts should clearly identify the items required and should specify the correct name of the part. If this type is used for replacement. Gasketed joints require smooth. & Y. or. DISASSEMBLY Small valves of the union bonnet type or of the screw bonnet type are readily disassembled by unscrewing the union nut or the bonnet. The drawing and revision number which appears on the identification disc attached to the handwheel is of particular value.S. is the pattern number of the handwheel and has no relation to the ordering of other valve parts. This recommendation applies to gland bolting as well. Tight bolt threads may be loosened by applying penetrating oil to the threads or by selectively heating the bolt at the point of thread engagement. type are caused by either dry. however. Prices for valve parts will be furnished on application. make sure the packing gland bolting is pulled down evenly so the gland will not bind against the stem. an O. before installing new packing. At the same time.S. type valve could be substituted. if practical. tamp them well into place. On bonnet joints of the through bolt type. Vogt uses a split ring type packing. type. angle. fill the stuffing box with penetrating oil. the bolts may be cut between the body and bonnet flanges for removal. Wipe all parts of the stuffing box. it is recommended that bolt torque be checked periodically. new packing is the remedy. drawing and revision number. and check valves. material. may loosen the stem. TOOLS FOR INSTALLING REPLACEMENT PARTS Wrenches are available (price on application) for the removal and replacement of renewable seats for globe. be sure valve is relieved of all pressure. If stem is still tight. and if the surface of the stem in contact with the packing is in good condition. or nonlubrication of yoke nut threads. A few hammer taps to the side of the bonnet nut or around the body neck of screw bonnet type valves will loosen nut or bonnet. In bolted bonnet valves. Before repacking. worn packing. repairs can be made without removing the valve from the line provided there is enough wrench room for loosening and tightening the bonnet nut. On bolted bonnet valves in high temperature service. STEMS Tight stems in valves of the O. If the stem turns freely after all packing is removed. having a prefix letter “V”. series numbers rnay be found on the side of the valve body or drawing numbers may be found on the bonnet flange. In the absence of an identification disc. using the packing gland as a tamping tool. the nut should be removed from the bonnet stud bolts or hexagon head cap screws removed from the body.Flow Control Division Care and Maintenance of Vogt Forged Steel Valves REPLACEMENT PARTS…HOW TO ORDER Genuine replacement parts are available for Vogt current standard valves and can usually be shipped from stock. turn valve to upright position. The wrenches are machined to an accurate finish to fit the spline broach on the inside diameter of the seat and are properly heat treated for strength and toughness. or the stem bonnet threads may “freeze” from excessive service temperatures or from corrosive fluids in the valve. and particularly where severe thermal cycling is involved. The purchase date and/or purchase order number will further identify the parts and materials originally ordered. A tight stem in an inside screw valve may also result from worn or overcompressed packing. 138 Vogt Valves BONNET JOINTS On valves of the union bonnet type. Then add enough packing to fill the . and opening and closing the valve a few times. The backseat should be used as a temporary measure to control the stem leakage until a shutdown provides safe repacking conditions. take care to stagger the ring slits so that they are not in line. and size of packing. inside and out. etc. After putting in a few rings. All parts are made with the same careful inspection and laboratory control given original valves and parts. a new bonnet and stem are required. especially valves with custom designed features. care should be taken not to overcompress the packing. valve size and series number. clean surfaces on both the body and the bonnet gasket faces. Before loosening the bonnet nut. The embossed number on each handwheel. and a new gasket is recommended for reassembly. Applying a few drops of oil to the stem threads and packing. and let soak. The seat threads in angle. Apply a light coat of fine. compound. angle. Pressure on the packing is applied by the packing nut or gland flange bolting.010”. 139 Vogt Valves . or indentations not deeper than 0. Vogt piston check valves require an adapter to screw into the piston for lapping the piston seating surface to the seat.) stuffing box. lapping will usually restore the surfaces sufficiently to permit tight closure. For relapping the seat and disc of Vogt globe. a valve bonnet with yoke nut removed may be used For relapping loose disc globe valves. see Figure 2 Ball check valves are primarily used for fluids of high viscosity and the rolling action of the ball maintains seating surfaces in good condition until ball size or ball guide is worn and replacement parts are needed. This will clearly show the extent of damage. depending on valve design. When installing new seats by using proper seat tools. and lap using an oscillating motion. or D. use the coarse. a few turns of the handwheel and a few drops of oil applied on the stem just above the packing will help work in the packing to the stem. Lap a few minutes and then wipe seating surfaces clean. and check valve bodies should be carefully inspected to make sure they are in useable condition.010” can seldom be corrected by lapping. globe. If severe damage is noted. the seats should be screwed tightly into the valve body. Globe and angle valves require a lapping guide fixture to maintain alignment during the lapping operation. or check valves. insert disc or one-piece stem into seat. Upon reassembling the valve. However. DISC AND SEAT Leakage through seat and disc is not always easy to detect. place a washer between the disc and head of the stem and retighten the disc nut. it will have precisely the same relationship to the seats that it had in the original assembly. Defects deeper than 0. compound and lap until all defects are removed. use a fine and a coarse grade emery base compound such as Clover Compound A and D.S. compound to the seating surface of disc or one-piece stem. A fixture as shown in Figure 1 may be made or. care should be taken when removing the wedge to note and mark its orientation with respect to the valve body so that when the wedge is reinserted in the valve. as shown in Figure 1. Gland bolting should be tightened evenly to obtain the proper packing compression for leak free service. or A. which bears on a gland in the stuffing box. Then finish with the fine. immediate repair is recommended since delay may permanently damage the disc or seat or both. for O. or A. but seating surfaces can be remachined or new parts installed. The internal repair of gate valves 2” and smaller is usually found to be uneconomical. then unscrewed and examined to make sure they are making continuous contact for tight seal. but when definitely known to exist. The bore of the valve body serves as a guide for lapping. slight pitting. It is recommended that the face of the disc be “blued” to check for contact between seating surfaces after final lapping. & Y valves. If seating surfaces show galling.Flow Control Division Care and Maintenance of Vogt Forged Steel Valves (cont. grooving. if a gate valve is disassembled for inspection or cleaning. For other valves consult your Vogt sales or engineering staff.Flow Control Division Vogt Valves Recommended Spare Parts for Vogt Valves Packing Matrix A high degree of standardization of Vogt valves permits a small stock of replacement packing and gaskets to service your Vogt valves. 600. The following matrix and part number tables provide the details for the purchasing of replacement gaskets for your Vogt bolted bonnet valves and packing for our popular class 150. 140 .* Pressure Class NPS DN 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 2-1/2 65 3 80 4 100 150 Conventional Port B B C D D E F F G 300 Conventional Port B B C D D E F F G 600 Conventional Port B B C D D E F F G 800 Conventional Port B** B C D D E F F – 1500 Conventional Port J J D E E F – – – 600 & 800 Full Port B C D – E F – – – 1500 Full Port B D E E F – – – – **Also 1/4 & 3/8 sizes Packing Set Part Numbers Matrix Flexible Graphite Packing Set PN Teflon Packing Set PN B 36323R DC00065 36451T4 DC00065 C 36323R DU00065 36451T6 DU00065 D 36323R EG00065 36451T6 EG00065 E 36323R EU00065 36451T6 EU00065 F 36323R FI00065 36451T6 FI00065 G 36323R FU00065 36451T5 FU00065 J 36323R DT00065 36451T9 DT00065 *API 602/ASME B16. 300. globe and angle valves. 800 and 1500 gate.34 type valves—see valve description. Flow Control Division Recommended Spare Parts for Vogt Valves Gasket Matrix Pressure Class NPS DN Vogt Valves (Spiral Wound Type) 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 2-1/2 65 3 80 4 100 150 Conventional Port A A B C C D E E F 300 Conventional Port A A B C C D E E F 600 Conventional Port A A B C C D E E F 800 Conventional Port A** A B C C D E E – 1500 Conventional Port A A B C C D – – – 600 & 800 Full Port A B G – D E – – – 1500 Full Port A B C C D – – – – **Also 1/4 & 3/8 sizes Gasket Matrix A B C D E F G Part Number (Including Suffix) 31102S2 G18029 31102S2 G33029 31102S2 G51029 31102S2 T33029 31102S2 T51029 31103S3 (Same as above) 31107S7 (Same as above) 31105S5 (Same as above) 31114S8 (Same as above) 31119S (Same as above) 31104S4 (Same as above) Spiral Wound Gasket Description* 304/Graphite Filled 316/Graphite Filled Monel/Graphite Filled 316/Teflon Filled Monel/Teflon Filled (Same as above) (Same as above) (Same as above) (Same as above) (Same as above) (Same as above) *USAGE TABLE Gasket 304/Graphite 316/Graphite Monel/Graphite 316/Teflon Monel/Teflon 141 Where Used A105. F316 Valves MM & HF Acid Trimmed Valves “T” Suffix Trimmed Valves Chlorine Valves . F9. F11 Cl.3 Valves A182. 2 & F22 Cl. A182-F5. SW12161 1 1-1/4.373. SW12111.363.Flow Control Division Vogt Valves Bonnet Replacement Assemblies Series 21000-Vogt Valve Replacement Bonnet Subassemblies Some valve end users find it more expedient to replace the bonnet subassembly. SW12161 353.00 Write for Vogt’s installation procedure covering instructions for proper field replacement of the series 21000 replacement bonnet subassemblies. ■ Repacking made easy ■ Promotes quick change ■ Completely packed and ready to install ■ Supports valve repacking in valve shop environment ■ High degree of standardization permits retrofitting of popular Vogt Class 150. and 800. of A105 bolted bonnet design with 13 Cr. 12161. SW12111. and 800. 300.363. 12161. Series 21000 A105/13 Cr. complete with new packing. 300. To support this maintenance philosophy. SW12111.12111. Specify the desired replacement Bonnet Assembly Package for the valve size and series you intend to repack by replacing the bonnet subassembly. SW12161 353.12111. Vogt valve users may purchase A105 bonnet subassemblies for replacement on their Vogt valves by specifying the parts numbers noted below.12111. can be repacked in a valve repair shop environment and be used during a later valve repacking cycle. 12161. 13 Cr. if not damaged and are serviceable.75 21000 08 5.363. SW12111. bolted bonnet valves. 600. when repacking small bore valves.12111.373.373. Trim Order by this number: Valve Size For Valve Series No.373. trim.75 21000 09 7. The Replacement Bonnet Assembly Packages can be easily installed on most existing in-line Compact Design Gate Valves in Classes 150. The removed bonnet assemblies. 3/4 353. 12161. SW12161 353.00 21000 06 4.363. 1/2. 142 . 1-1/2 2 Retrofit Bonnet Assembly Package No. 21000 04 E 4. trimmed. 600. There are no warranties of any kind other than those stated herein. direct. Have proper replacement parts. and should specify the correct name of part. drawing and revision number. etc. more trouble-free service when properly installed in recommended applications. trained personnel. All parts are made to gauge with the same careful inspection and laboratory control given original valves.) . or consequential damages however resulting from any cause whatsoever. CHECK VALVE Preliminary Considerations 1. Use experienced. This information is shown on the identification disc which is attached to the handwheel. 2. Orders for replacement parts should clearly identify the items required. especially those for special valves. however. material. Observe all standard safety precautions. and it is recommended that valves be returned to the factory for inspection and rework when major repairs are indicated. indirect. If possible. Use proper tools. In no event are we liable for any special. The date of purchase and/or the order number will further identify the parts. major repairs are discouraged. however. remove valve from line so that work can be done in a clean. 6. well lighted area.Flow Control Division Vogt Valves Typical Nomenclatures for Valves GATE VALVE REPLACEMENT PARTS FOR VOGT VALVES Vogt valves are carefully made from selected materials to give longer. Vogt valves repaired in the field do not carry the “Product Warranty” of valves repaired in our own facilities. valve size and series number. 3. But proper care and maintenance in the field can contribute significantly to good performance. 4. The following information is offered as an aid to field maintenance of Vogt valves. 5. Pressure test valve before reinstalling. 143 GLOBE VALVE Replacement Parts—How To Order Genuine replacement parts are available for all Vogt valves and can usually be shipped from stock for all standard valves. (See pages 140-142 for recommended spare parts and replacement bonnet assemblies. This is particularly essential on valves intended for critical service. Much of the field maintenance is of a routine nature and can be readily performed by the user. 915 48.5 .625 8.38 9.5 .3017 .2 .71953 8 3.406 61.6809 .0 .660 1.540 .766 .7235 .2609 .31875 5.7125 Vanish Threads V Diam.020/-.2726 .6809 . Tolerances Column A Dimensions +.500 4. ASME B1.840 1.23863 1.49163 .2500 .98887 1. L3 .625 Pitch Diameter at Number of Beginning of External Threads Thread Per Inch E0 36351 27 .1285 .875 3.6828 .313 Bold face numerals are in inches.00mm above 1-1/2”).62 16.96768 14 1.20.70391 3.00mm thru 1-1/2”). Diam.19733 1.83750 8 4.063 Length.50 12.000 (+.094 1.4/-.187 1.000 thru Size 2" (+.2500 .50003 . External L2 .2 B-Socket Depth .400 .8 4. For sizes above 2" Dimensions +.29627 2.436 .675 42.025/.4337 .50 12.2500 .62 16.4018 .4337 . 3Also pitch diameter at gauging notch (handtight plane).320 .3000 1.1667 .34062 8 3.1375 1. Inc.5343 .38712 5.75 19. The above information taken from the American National Standards Institute.844 .1615 .75843 14 .3945 .54083 1. for pipe threads.61201 18 .5 . Metric version not available. Standard gauging tolerance equals plus or minus one thread on both male and female threads.88881 4.2278 .37360 .682 .2500 1.95429 1. 5Dimensions given do not allow for variations in tapping or threading.0 .958 1.50 12.4078 .38 9.555 14.46697 .2500 .50597 8.2500 Total Normal Engagement5 L1 + L3 .39073 8 6.0 (Min.2478 .77978 2.38 9.5 .339 ..821 .41797 L1 .43047 8.79609 11 1/2 2.4067 .9 3.3.420 . 1/4 15 3/8 10 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 2-1/2 65 3 80 4 100 A-Socket Dia.25272 2.375 2.1111 .5457 .43359 8 Length2 of Effective Thread.545 115.0 .2478 .065 27.675 .6 .5 .6609 . 4Also length of thin ring gauge and length from gauging notch to small end of plug gauge.315 1.5/-.32500 3.4337 .4337 .1928 .8 1.21363 11 1/2 1.2500 .5125 1.2609 .6969 . ASME Standard Taper Pipe Thread1 Nominal Pipe Size Outside Diameter of Pipe D 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 .58338 1.62 16.2 2.44929 6.60160 . While this implies a greater degree of precision than is ordinarily attained.050 1.500 5.855 21.330 33.2143 .906 73.4063 1.2609 . .82188 4.937 .1667 .55713 11 1/2 1. .38850 3. Blue numerals are in millimeters.240 .2609 . E1 .62701 .5533 .5337 .33438 8 5.9 1.2000 1.76216 3.5 .37511 6.8 2.26902 11 1/2 2.4337 .3017 .690 17.4337 . ASME B16.1.74504 .208 1.Flow Control Division Vogt Valves Thread & Socket Weld Standards Basic Dimensions.44609 8 8.77843 .405 .1928 . E3 .5 .900 2.47739 18 .3017 . 2Also length of plug gauge. these dimensions are the basis of gauge dimensions and are so expressed for the purpose of eliminating errors in computations.9320 1. Wrench Make-up Length for Internal Thread Handtight Engagement Length4.016 1.2500 .563 6.2639 .000 4.50 12.82234 2.8 1.420 .535 89.4337 Socket Weld Dimensions For Valves & Fittings Valve Size NPS DN Dimensions are in inches (metric not provided).35656 .2143 .7565 1.071 1.11-96) 144 1The basic dimensions of the ASME Taper Pipe Thread are given in inches to four or five decimal places.3017 .7068 .7 1. 068 77.00 4.133 3.250 6.90 4.2 .315 33.626 295 .24 Blue numerals are in millimeters and kilograms.35 22. Per Ft.563 116 .24 18. Schedule 100 Wall Thick.11 13. Wt.276 7.064 140 183 230 .50 1.594 12.62 10.126 3.72 4. Schedule 10 Inside Dia.4 .47 1/4 8 . .900 48.48 88.91 3.276 7.41 1.92 2.44 3.69 1.02 .39 64.88 11.46 11.08 11.562 .54 5.071 10.8 .54 5.215 5. 1/8 6 .05 38.900 73.77 1-1/2 40 1.28 4.27 .1 .73 .436 11.1 .280 7.095 2.03 5 125 5.100 27.26 ~50.55 57.44 107.11 18.29 3.154 3.64 96.844 14.70 15.300 58.63 2.3 4.501 7.8 .761 146 . Inside Dia.318 8.1 .9 . Inside Dia. Per Ft.8 12.189 9.24 36.87 1.56 4.37 .614 .179 4.55 7.70 27.119 3.58 74.875 73.31 7.02 7.8 .20 .0 .4 .5 .65 5.500 10.400 10.815 11.8 .250 311 .43 64.2 .3 .02 10.16 79.03 75. Schedule 30 Wall Thick.6 .15 6.72 4.53 20.813 122 .9 .625 219.4 .406 10.56 3.2 .95 2. 1.55 14.939 49.73 1.365 8.95 53.382 9.1 .152 80. Per Ft.31 41. Inside Dia. Per Ft.56 73.01 7.70 43.32 53.74 1.622 15.55 7. Double Extra Heavy Wall Thick.77 4.32 21.47 .85 1. Per Ft.250 6.047 128 .13 1.32 159.49 22.307 7.44 36.25 15.70 34. Bold face numerals are in inches and pounds.750 19.252 6.63 5.38 1.277 .97 10.31 .11 5.250 . Wt.302 7.3 2.00 4.813 122 .78 5.69 . Wt.826 97. Per Ft.16 5.625 15.41 9.66 5.9 .109 2. Wt.154 3.01 7.’ 160.35 3.145 3.113 2.300 8.31 .56 14.18 28.200 5.55 2.57 .312 33.188 .17 3.49 186.02 7.25 15.281 7. Wt.73 11.1 .92 114.Flow Control Division Vogt Valves Dimensional Data for Standard & Schedule Pipe – Carbon Steel Pipe PIPE NPS DN Outside Dia.64 6.81 51.54 8 200 8.7 .3 1.0 .24 .813 9.546 13.74 1.133 3.7 .35 6.47 2.27 177.91 3. Schedule 60 Wall Thick.27 .125 28.50 38.62 21. Per Ft.2 . Wt.493 12.63 5.068 1.750 248 .840 21.824 20.56 14.432 10.300 7.314 189 237 .625 194 .548 90. Schedule 80 Wall Thick.6 .41 2.25 1.154 3.8 15. Inside Dia.179 4.067 52.2 .3 .344 8.74 81. Wt. Wt.000 305 .250 6.308 7.7 .48 1. Per Ft.70 35.46 12.27 3.5 .91 10.380 35.439 9.63 132.62 21.09 1.55 40.01 14.57 .35 67.109 2.04 40.147 3. Inside Dia.203 5.5 .068 1.74 9.6 3.02 .77 8.56 6.58 11.64 54.7 .44 1.42 97.844 21.3 5.02 10.625 168.981 10.18 9.68 2.500 12.50 38.07 3.599 15.812 1.250 4.47 2.97 28.13 19.2 .068 77.438 11.049 26.719 1 5. Wt.69 13.2 1.64 111.63 3. Per Ft.09 18. .3 .237 6.55 42.70 54.438 11.97 28.5 .624 92.11 18.16 5.7 .41 .77 65.813 8.79 16.7 .68 2.87 1.58 11.154 3.0 .14 10.44 2.62 .258 6.45 1-1/4 32 1.97 4.55 14.67 208. Standard Wall Thick.06 7.095 2.75 273 1. Inside Dia.546 13.064 281 .136 205 257 .719 18.04 33.57 3.22 Wt.3 .562 14.27 238.17 3.358 9.8 .9 .11 145 2.97 5.469 62.189 132 .77 .322 .313 110 .39 3 80 3.200 5.20 11.552 13.85 3.57 4.31 .44 133.41 1.53 20.216 5.4 .026 102 .58 139.500 12.48 42.091 2.08 3.113 2.66 11.27 28.688 17.31 9.08 12.323 59.32 4.73 1.7 .939 49.500 88.000 101.540 13.0 2.79 8. Per Ft.48 60.10 Inside Dia.906 1.065 154 .0000 25.218 5.548 90.280 7.24 .27 2.85 1.57 42.54 41.13 1.719 .71 89.78 30.05 2.50 .063 103 .54 .7 .92 10 250 10.203 5.338 34.226 5.364 85.61 1.82 2.957 24.64 1 25 1.5 .32 4.56 Inside Dia.026 102 .323 59.140 3.35 1.258 6.5 .24 .35 3.375 9.27 3.824 20.218 5.76 104.160 29.09 1.9 3.6 20.63 .55 8.375 9.35 33. Extra Heavy Wall Thick.302 7.047 128 .55 3/4 20 1.84 1.5 .088 2. 1/2 15 . Inside Dia.125 23.761 146 .3 .39 60.73 12.37 .4 1.322 8.020 203 255 .1 .466 .432 10.088 2.750 198 248 .0 .750 323. Inside Dia.10 .97 28.98 22.77 . Schedule 160 Wall Thick.125 10.500 .215 5. Schedule 20 Wall Thick.26 45. Inside Dia.365 9.6 .625 9.08 81.660 42.260 .337 8.337 8.01 28.434 11.610 40.03 13.95 77.38 1.049 26.92 155.1 7.68 2.47 1.364 9.4 .500 173 216 .364 9.269 6.500 12.624 66. Wt.31 1 94 2.278 32.564 194 243 .70 65.493 12.500 12.0 .69 115.24 42 63 . Wt.50 18.826 97.875 22.376 289 .21 7.68 2.47 .07 9.32 3.03 7.13 14.3 .294 7.26 21.56 2.438 87.53 10.7 .PerFt. Schedule 140 Wall Thick.73 .07 5.49 7.58 27.9 .79 16.0 .594 .5 .41 .24 54.47 1.62 25.0 10.140 3.02 43.39 1.191 4.9 .69 20. Per Ft.65 5.9 .900 73.55 60.020 255 . Per Ft. Schedule 40 Wall Thick.27 40.750 179 222 .66 11.065 154 .119 3.674 17.503 38.11 13.57 42.04 7.48 2.957 24.75 267 1.8 .147 3.00 28.050 26.96 49.000 20.2 .226 5.145 3.600 15.74 7.622 15.91 1.56 2.98 22.33 12 300 12.24 1.090 307 *.237 6.278 32.8 .51 33.13 100.364 85.41 1.771 5.74 53.52 79.500 114.191 4.76 .20 .39 1.40 67.897 124 .63 4 100 4.42 .1 .51 18.36 28.531 13.79 8.875 175 .12 27.125 54 0 375 9.39 64.56 2 50 2.3 6.76 5.375 60.96 11.23 72.75 5.77 6. Inside Dia. Wall Thick.675 17.750 298 .318 8.53 49.31 .300 7.380 35.742 18.938 303 .750 273.26 5.26 .97 28.44 2-1/2 65 2.62 10.05 1.269 6.216 5.78 30.88 32.7 .01 7. Schedule 120 Wall Thick.38 43.15 108.74 9.71 2.406 +.84 .27 18.20 .80 24.375 9.84 .001 8.689 42.4 107.126 3.55 2. Wt.14 4.80 3/8 10 .80 .469 62.981 203 .610 40.43 6 150 6.067 52.24 .09 3.1 .20 90.864 21.9 .86 7.38 49.091 2.126 257 1.896 22.63 3.08 12.742 18.70 5.40 125.9 .68 3-1/2 95 4.27 73.54 .219 .405 10.62 .85 3.31 12.29 2.49 7.9 .563 141.08 3.91 1.7 .20 .423 10.27 3.15 6.250 206 .423 10. 07 5.375 9.55 42.47 1.278 32.682 42.1 10 250 10.3 2 50 2.065 1.65 1.625 194 .9 .61 8.50 1.047 128 .065 1.026 102 . 1/2 15 .3 2-1/2 65 2.5 .134 3.5 .62 1025 15.16 5. 10S (a) Wt.203 5.42 .80 .29 13.5 .226 5.28 1.63 .049 26.6 .47 6.900 48.8 .065 1.54 .315 33.300 7.119 3.77 2.157 54. Per Ft.56 7.295 135 .87 1.98 22.91 3.200 5.120 3. Schedule 5S Wall Thick.76 13.27 3.77 9.48 3.79 10.77 2.109 2.260 108 .11 2.24 .70 1.7 .260 82.4 .126 3.120 3.7 .9 3-1/2 95 4.54 .62 .63 .54 5.30 1.42 .74 96.065 154 .113 2.84 5.56 73.4 1-1/4 32 1.625 168.307 7.55 10.140 3.165 4.323 59.11 3. Schedule Wall Thick.405 10.73 1.742 18.93 14.761 146 .97 5.66 11.120 3.432 10.065 1.3 1/4 8 .92 28.957 24.68 2.53 49.77 7.2 .357 161 .69 1.109 2.364 85.53 5.9 .088 2.469 62.546 13.63 3.380 35.0 12 300 12.407 213 .48 2.750 273.0 .900 73.24 1.80 .05 4.27 40.939 49.420 265 .180 4.500 12.9 .635 66.218 5.9 .17 3.97 28.65 .44 2.25 .91 1.01 7.3 8 200 8.09 1.56 14. 146 .3 5 125 5.92 5.8 .51 18.67 1.27 .40 9.13 1.8 .51 3.423 10.083 2.109 2.3 3/4 20 1.216 5.050 26.7 .981 203 .33 6.884 22.337 8.1).530 38.39 1.31 .5 .09 2.58 11. Per Ft.563 141.39 64.245 57.318 8.493 12.9 .10 .65 .109 2.32 8.65 5.62 21.33 .49 .065 1.083 2.482 266 .750 323.065 1.08 3.27 3.64 3.709 68.438 316 .540 13.410 10.36 5.65 .69 1.9 .8 .09 1.45 3.7 .93 2.03 1.145 3.57 4.0 . Schedule Wall Thick.29 3.840 21.19M-1985 Standard (except inside diameter and DN size notation).78 30.020 255 .68 2.065 1.390 315 .05 5.28 1.8 1.77 .4 .334 110 .068 1.50 38.09 3.0 3 80 3.0 .067 52.920 23.60 11.068 77.545 13. Inside Dia.65 1.PerFt.083 2.083 2.179 4.02 10.65 1.11 .74 9. Blue numerals are in millimeters & kg/meter.56 2.750 298 ❒ .1 .280 7.19 22.00 4.70 43.760 95.258 6.48 5. CARBON STEEL PIPE DATA – STAINLESS STEEL PIPE DATA – Extracted from ASME B36.500 12.77 11.134 3.70 54.81 2.03 4.01 11.47 2.98 31.6 .500 88.329 212 .40 2.625 219.77 1.0 .133 3.78 12.813 122 .154 3.1 Inside Dia.55 2.10M-1985 Standard (except inside diameter and DN size notation).65 .500 12.7 .37 .19 18.63 3.86 1.109 2.63 12.77 1.57 24.407 163 .10.97 7.276 7.770 44.824 20. Bold face numerals are in inches & lb/ft.20 .1 .5 .322 8. PIPE 1/8 6 .1 .57 42.57 .85 3.11 18.9 .73 .05 3.74 1.834 97.79 16.38 1.55 14.215 5.88 .72 4.095 2.548 90.120 3.375 60.57 6.302 7.500 114.375 9.41 1. 40S Wt.750 248 ❒ .3 .237 6.84 8.2 1-1/2 40 1.4 .11 2.049 1.097 27.11 3.7 1 25 1.41 2.18 28.61 2.065 1.32 4.1 .11 13. 80S Wt.8 .148 3.9 .345 136 . (a) Wt.3 .96 20.31 11.65 1.96 10.2 .20 .442 36.49 7.40 4.156 3.69 3.91 2.365 9.02 7.826 97.47 .63 5.24 .11 1.109 2.70 65.8 .11 3.710 18.083 2.8 .154 3.40 7.08 12.3 6 150 6.091 2.4 .334 84.7 .42 132.18 4.364 9.65 27.87 1.05 2.26 3.000 101.Flow Control Division Vogt Valves Dimensional Data for Standard & Schedule Pipe Stainless Steel Pipe NPS DN Outside Dia.875 73.1 .6 4 100 4.938 303 ❒ .00 .02 . NOTE: ❒ These do not conform to ASME Standard B36.05 4.40 15.8 .53 20.24 .674 17.083 2.26 7. Inside Dia.20.11 .40 2.77 6.109 2. Extracted from ASME B36.48 60.77 6. Inside Dial Schedule Wall Thick.147 3.PerFt.660 42.3 .64 9.79 8.610 40.36 9.134 3.269 6.85 1.19 .65 .675 17.17 36.40 19.31 .7 3/8 10 .41 .185 30.08 (a) Wall thickness of schedule 5S & 10S does not permit threading in accordance with USA Standard for pipe threads (ASME B1.84 .622 15.28 .191 4. 8 ft-lbs 1. Class 800 Reduced Port Gate 1/4".15701.0 ft-lbs Note: Reduce above values by 25% to 30% if any type lubrication is used on bolting.2 ft-lbs 7.2 ft-lbs 3/8" 40 36 3/4 1. 3/8" . Closing Torques (Typical in Ft-lbs) (701. etc.9 ft-lbs 15.7 ft-lbs 4.9 ft-lbs 5/8" 125 115 2 7.57 psi 1 1/2" .5 ft-lbs 7/16" 50 45 1 3.9 ft-lbs 3/4" 175 156 2 1/2 8.5 ft-lbs 15.70 ft-lbs Class 800 Full Port Gate 1/2" -15 ft-lbs 3/4" ..9 ft-lbs 9/16" 144 130 1 1/2 4.7 ft-lbs 4.30 ft-lbs 1 1/2" .5 ft-lbs 13..52 psi 1 1/4" -. 3/4" .57 psi 2" .5 ft-lbs 8.20 ft-lbs 1" .40 ft-lbs 1 1/2" . Unlubricated Values) Size 300.15 ft-lbs 1" .15 ft-lbs 3/4" .0 ft-lbs 7. 147 .8 ft-lbs 4.15 ft-lbs 1" ..40 ft-lbs 1 1/4" .Flow Control Division Engineering Information (English Units Only) Vogt Valves Check Valve Cracking/ Opening Pressures Handwheel Max.8 ft-lbs 3.) 1/2"-.50 ft-lbs 1 1/2" .15 ft-lbs 3/4" .9 ft-lbs 1/2" 85 75 1 1/4 4.5 ft-lbs 1" 795 710 4 12.8 ft-lbs 1/2".9 ft-lbs 13. 573.50 ft-lbs 2" .75 ft-lbs 2" .20 ft-lbs 1 1/4".30 ft-lbs 1" .5 ft-lbs 7/8" 530 480 3 8. 1 1/2" .70 ft-lbs 2" .58 psi All spring loaded Check valves have cracking pressures of 10-12 psi. 593.61 psi 1" . 583. Port Class 600 & 800 Full Port Class 1500 Class 1500 Full Port Bolt Diameter Torque (ft-lbs) B7 & B16 B8M 5/16" 25 22 1/2 1. Closing Torques (Typical in Ft-lbs) Handwheel Max.0 ft-lbs 7.5 ft-lbs 13.40 ft-lbs 2" .100 ft-lbs Class 800 Reduced Port Globe 1/2" .61 psi 3/4"-.2 ft-lbs 4.0 ft-lbs 13.75 ft-lbs Class 800 Full Port Globe 1/2" . 600 & 800 Conv.125 ft-lbs Recommended Maximum Bonnet Bolt Torques Maximum Packing Gland Bolting Torque (Dry. 0 1145.5 319.70 13.16 8.91 1.0 1348.5 783.84 31.5 61 62 63 64 65 884.0 86 87 88 89 90 1247.98 (1 Bar = 105 Pa = 14.44 211.0 246.96 77.5 261.5 pounds per square inch) 40 88.5 435.48 39.0 188.59 94.4536 kilogram) Pounds 0 1 2 3 4 5 6 7 8 9 0 0. per Sq.41 20.52 61.05 24.13 23.35 167.0 46 47 48 49 50 667.18 90.79 12.5 16 17 18 19 20 232.63 4.5 1276.23 112.82 205.23 209.98 185. per Sq.89 20 44.61 8.32 21.5 754.45 44.73 160.30 70 31.18 42.5 609.0 652.55 44.30 145.23 15.0 1203 5 1218 0 1232. Inch 41 to 60 Bar Lbs. Inch 1 2 3 4 5 14.5 406.46 28.62 202.27 37.38 35.36 1.14 18.67 28.20 4.56 39.5 31 32 33 34 35 449.73 63.18 3.0 1377.41 6.48 29.5 551.91 152.20 37.Flow Control Division Vogt Valves Weight Conversion Pounds to Kilograms (1 pound = 0.60 191.5 1131.14 68.91 55.59 24.19 187.81 2.75 74.0 11 12 13 14 15 159.0 768.0 1087.83 80 36.34 70.87 182.95 25.2046 pounds) Kilograms 0 1 2 3 4 5 6 7 8 9 0 0.0 217.0 971.55 169.07 35.5 91 92 83 94 95 1319.0 855.21 32.61 14.5 638.82 41.0 130.35 6.64 116.09 143.09 43.90 6.73 42.14 165.48 136.62 20 9.0 420.26 Pressure Conversion 1 to 20 Bar 148 Lbs.71 8. Inch 21 to 40 Bar Lbs.21 101.97 15.94 163.32 59.58 29.0 1290.0 1261.5 1421.06 14.39 30.65 38.53 158.5 1015.10 38.89 11.5 1073.26 7.47 34.27 2.0 275.66 127.08 10 4.72 3.0 826.57 180.25 26.0 66 67 68 69 70 957.5 290.77 22.50 50.5 870.0 43.99 5.5 928.75 32.66 30.42 15.5 696.0 710.66 33.5 493.0 1116.57 83.53 9.00 196.94 30.5 348.5 986.09 46.87 21.0 1058.0 536.0 1406. Inch 61 to 80 Bar Lbs.44 5.45 0.30 48.64 19.50 147. per Sq.05 218.75 171.02 13.5 841.22 27.5 1334.0 913.54 4.07 60 132.84 10 22.01 39.5 81 82 83 84 85 1174.5 1189.80 7.96 174.29 36.43 10.82 108.31 26.84 119.0 56 57 58 59 60 812.0 72.12 28.37 90 40.71 149.5 1044.32 156.5 29.12 70 154.28 134.74 37.03 50 110.03 29.02 34.33 16.91 Kilograms to Pounds (1 kilogram = 2.0 507. Inch 81 to 100 Bar Lbs.60 19.0 1000.68 23.41 103.50 19.93 35.46 125.80 194.57 34.25 123.89 141.15 30 13.0 565.0 76 77 78 79 80 1102.0 .88 16.0 333.05 121.5 464.0 1435.0 478.62 105.49 24.0 391.24 17.64 43.92 40.37 178.5 1160.07 9.5 580.43 114.98 10.0 96 97 98 39 100 1392.86 26.5 174.5 41 42 43 44 45 594.39 189.12 57.43 17.0 36 37 38 39 40 522.00 44.0 362.0 681.68 41.28 41.55 72.0 942.40 25.5 116.76 60 27.00 0.80 97.85 216.5 145.5 1363.34 11.5 21 22 23 24 25 304.5 1450.37 81.0 26 27 28 29 30 377.39 92.23 50 22.46 39.5 203.5 725.16 79.s 51 52 53 54 55 739.04 24.82 11.0 623.41 200.0 797 s 71 72 73 74 75 1029.0 101.25 12.69 40 18.00 99.64 213.5 6 7 8 9 10 87. per Sq.86 33.16 80 176.93 Bar to Pounds per Square Inch 30 66.78 17.5 1305.05 19.52 14.21 90 198.11 33. per Sq.87 130.77 85.00 2.03 207.5 58.96 20.5 899.71 52.69 138. 4 75.4° to 0° CEL. read Celsius equivalent in left-hand column.8 116.8 188.9 –13.1 31.6 190.3 18. read Fahrenheit equivalent in right-hand column.6 –5.1 26.4 147.0 168.4 174.3 33.2 185.8 23.0 51.3 23.6 199.4 –454 –436 –418 –400 –382 –364 –346 –328 –310 –292 –274 –256 –238 –220 –202 –184 –166 –148 –130 –112 –94 –76 –58 –40 –22 –4 14 32 5 Conversion Formulas C = — (F .0 30. If in degrees Celsius.4 210.6 –10.1 11.6 26.0 87.2 –11.2 203.1 21.0 204.6 0.6 11.2 68.3 8.0 10.0 C 16.8 170.7 12.2 149.6 1° to 60° CEL.2 –1.6 91.7 2.6 208.0 –14.0 105.8 43 49 54 60 66 71 77 82 88 93 99 100 104 110 116 121 127 132 138 143 61° to 290° CEL.2 37.7 17.6 127.2 131.4 93.2 167.8 62.9 24.2 41.8 179.4 138.0 60.6 46.4 –13.2 50.6 64.6 36.2 158.8 152.6 145.0 5.6 163.4 –3.3 –2.9 14.9 4.4 129.2 113.8 134.4 15.4 183.6 100.8 107.7 22.8 71.2 17.1 6.8 3.4 192.2 176.3 28.4 5.6 31.6 428 446 464 482 500 518 536 554 149 154 160 166 171 177 182 188 193 199 204 210 215 221 227 232 238 243 249 254 260 266 271 277 282 288 293 299 304 310 316 321 327 332 338 343 349 354 360 366 371 377 382 388 393 399 404 410 416 421 427 432 438 443 449 454 460 466 471 477 300° to 890° CEL.6 154.4 20.1 –5.7 27.4 30.8 79.8 28.0 –4.1 1.8 18.2 212.2 140.7 32.6 –15.8 13.0 114.6 118.2 122.4 102.1 –10.8 8.2 27.4 66.2 59.9 34.2 2.7 –6. 300 310 320 330 340 350 360 370 380 390 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650 660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850 860 870 880 890 F C 572 590 608 626 644 662 680 698 716 734 752 770 788 806 824 842 860 878 896 914 932 950 968 986 1004 1022 1040 1058 1076 1094 1112 1130 1148 1166 1184 1202 1220 1238 1256 1274 1292 1310 1328 1346 1364 1382 1400 1418 1436 1454 1472 1490 1508 1526 1544 1562 1580 1598 1616 1634 482 488 493 499 504 510 516 521 527 532 538 549 560 571 582 593 604 616 627 638 649 660 671 682 693 704 732 760 788 816 843 871 899 927 954 982 1010 1038 1066 1093 1121 1149 1177 1204 1232 1260 1288 1316 1343 1371 1399 1427 1454 1482 1510 1538 1566 1593 1621 1649 Locate temperature in middle column.2 86.6 55.4 –8. OR FAH.2 32.8 44.1 16.6 109.4 35. OR FAH.8 -459.0 123.4 25. OR FAH.0 195. if in degrees Fahrenheit.2 7.8 125.7 37.2 104.4 165. OR FAH.9 –8.0 150.32) 9 9 F = — C + 32 5 C –17.2 12.1 –0.2 95.0 159.3 3.6 1.3 –12.4 –450 –440 –430 –420 –410 –400 –390 –380 –370 –360 –350 –340 –330 –320 –310 –300 –290 –280 –273 –270 –260 –250 –240 –230 –220 –210 –200 –190 –180 –170 –160 –150 –140 –130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10 0 F –459.6 82.4 120.6 172.9 29.7 7.2 –6.8 53.0 42.0 69.8 206.2 –16.4 39.0 96.3 –7.2 194.2 22.0 15. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 F 33.7 –16.4 57.8 98. –459.8 161.2 77.1 –15.0 –9.9 9.6 136.4 48.8 –12.8 33.Flow Control Division Vogt Valves Temperature Conversion Celsius (C) To Fahrenheit (F) — Fahrenheit (F) To Celcius C –273 –268 –262 –257 –251 –246 –240 –234 –229 –223 –218 –212 –207 –201 –196 –190 –184 –179 –173 –169 –168 –162 –157 –151 –146 –140 –134 –129 –123 –118 –112 –107 –101 –96 –90 –84 –79 –73 –68 –62 –57 –51 –46 –40 –34 –29 –23 –17. 900 910 920 930 940 950 960 970 980 990 1000 1020 1040 1070 1080 1100 1120 1140 1160 1180 1200 1220 1240 1260 1280 1300 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 2250 2300 2350 2400 2450 2500 2550 2600 2650 2700 2750 2800 2850 2900 2950 3000 F 1652 1670 1688 1706 1724 1742 1760 1778 1796 1814 1832 1868 1904 1940 1976 2012 2048 2084 2120 2156 2192 2228 2264 2300 2336 2372 2462 2552 2642 2732 2822 2912 3002 3092 3182 3272 3362 3452 3542 3632 3722 3812 3902 3992 4082 4172 4262 4352 4442 4532 4622 4712 4802 4892 4982 5072 5162 5252 5342 5432 . 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 110 120 130 140 150 160 170 180 190 200 210 212 220 230 240 250 260 270 280 290 F C 141.8 143.0 177.6 181.0 25.4 111. OR FAH.8 35.4 10.4 156.0 230 248 266 284 302 320 338 356 374 392 410 413.8 –7.0 20.7 –11.1 36.6 6.8 197.4 201.6 73.0 0.8 80.9 19.9 –3. 149 900° to 3000° CEL.3 13.0 132.0 35.8 –2.6 21.4 84.0 186.6 37.0 78.7 –1. 2nd Edition. 2nd Edition. Name _________________________________________________________________ Title __________________________________________________________________ Company ______________________________________________________________ Address _______________________________________________________________ City___________________________________________________________________ State __________________________ Country _______________________________ Zip ___________________________________________________________________ Telephone _____________________________________________________________ Keep up with Vogt valves Please put me on your mailing list for catalog updates.Keep up with Vogt valves Please put me on your mailing list for catalog updates. I would like a Vogt Valve Catalog & Application Manual (VV200. 2002) sent to the name and address below. Send me the latest Resource CD with interactive catalog. Send me the latest Resource CD with interactive catalog. 2002) sent to the name and address below. Send me the latest Resource CD with interactive catalog. Name _________________________________________________________________ Title __________________________________________________________________ Company ______________________________________________________________ Address _______________________________________________________________ City___________________________________________________________________ State __________________________ Country _______________________________ Zip ___________________________________________________________________ Telephone _____________________________________________________________ Keep up with Vogt valves Please put me on your mailing list for catalog updates. 2002) sent to the name and address below. I would like a Vogt Valve Catalog & Application Manual (VV200. I would like a Vogt Valve Catalog & Application Manual (VV200. 2nd Edition. Name _________________________________________________________________ Title __________________________________________________________________ Company ______________________________________________________________ Address _______________________________________________________________ City___________________________________________________________________ State __________________________ Country _______________________________ Zip ___________________________________________________________________ Telephone _____________________________________________________________ . IN 47130 Vogt Valves 5171 Maritime Road Jeffersonville. IN 47130 Vogt Valves 5171 Maritime Road Jeffersonville. IN 47130 Place Stamp Here Place Stamp Here Place Stamp Here .Vogt Valves 5171 Maritime Road Jeffersonville. express or implied.com Flowserve Corporation has established industry leadership in the design and manufacture of its products. operation. The purchaser/user must therefore assume the ultimate responsibility for the proper sizing and selection. Flowserve and Vogt Valves are registered trademarks of Flowserve Corporation. TX 75482 US Sales Offices Phone: 903-885-3151 Fax: 903-439-3386 Toll-Free Telephone Service 1-800-225-6989 Visit Our Website www. FLOWSERVE CORPORATION FLOW CONTROL DIVISION Vogt Valves 1511 Jefferson Street Sulphur Springs. Although Flowserve can (and often does) provide general guidelines.flowserve. Should any question arise concerning these provisions. the purchaser or user of Flowserve products should be aware that Flowserve products might be used in numerous applications under a wide variety of industrial service conditions.Flow Control Division Vogt Valves Vogt Valves 1511 Jefferson Street Sulphur Springs. and maintenance of Flowserve products. USA.flowserve. Nothing contained herein is to be construed as a warranty or guarantee. Irving. regarding any matter with respect to this product. installation. However. dimensions and information contained herein are subject to change without notice. Because Flowserve is continually improving and upgrading its product design.com or call USA 1-800-225-6989. For more information about Flowserve Corporation. contact www. While the information and specifications contained in this literature are believed to be accurate. When properly selected. The purchaser/user should read and understand the Installation Operation Maintenance (IOM) instructions included with the product. Texas. and train its employees and contractors in the safe use of Flowserve products in connection with the specific application. the purchaser/user should contact Flowserve Corporation at any one of its worldwide operations or offices. TX 75482 Phone: 903-885-3151 Fax: 903-439-3386 © 2003 Flowserve Corporation. VVACT0000 (Replaces VV-200) Third Edition 9/03 Printed in USA . this Flowserve product is designed to perform its intended function safely during its useful life. they are supplied for informative purposes only and should not be considered certified or as a guarantee of satisfactory results by reliance thereon. it cannot provide specific data and warnings for all possible applications. the specifications.