Flexi Multiradio 10 Base Station Product Description

March 28, 2018 | Author: Viet Trong Ho | Category: Direct Current, Mimo, Ethernet, Base Station, Network Switch
Share
Report this link


Comments



Description

WCDMA RAN, Rel.RU40, Operating Documentation, Issue 03 Flexi Multiradio 10 Base Station Product Description DN0971928 Issue 01C Approval Date 2013-09-17 Confidential Flexi Multiradio 10 Base Station Product Description The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2013. All rights reserved f Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set. The same text in German: f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen. Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen. Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes. 2 Id:0900d805809b557a Confidential DN0971928 Issue 01C Flexi Multiradio 10 Base Station Product Description Table of contents This document has 50 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DN0971928 1 1.1 1.2 Introduction to Flexi Multiradio 10 Base Station. . . . . . . . . . . . . . . . . . . . 9 Construction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2 RSS-310 compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3 EU RoHS statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4 CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5 FCC Part 15 compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 6.1 6.2 6.3 Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cost-efficient modular site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . One BTS for all network applications. . . . . . . . . . . . . . . . . . . . . . . . . . . Feederless and Distributed Site concept . . . . . . . . . . . . . . . . . . . . . . . . 7 7.1 7.2 Single RAN aspects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 RF sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Transport backhaul sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Baseband capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 9 9.1 9.2 9.3 9.3.1 9.4 9.5 Management and software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local Management Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote User Event Log Management. . . . . . . . . . . . . . . . . . . . . . . . . . RUEM concept - how does it work?. . . . . . . . . . . . . . . . . . . . . . . . . . . . Software updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External alarms and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 28 30 31 31 34 35 10 10.1 10.2 10.3 10.4 10.5 10.6 Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Radio Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 36 37 38 39 40 43 11 Appendix Flexi abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 12 Appendix Flexi BTS hardware releases. . . . . . . . . . . . . . . . . . . . . . . . . 47 Id:0900d805809b557a Confidential 17 17 20 21 3 Flexi Multiradio 10 Base Station Product Description List of figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 4 General architecture of Flexi Multiradio 10 Base Station . . . . . . . . . . . . 10 List of countries respecting EU Directive 1999/5/EC . . . . . . . . . . . . . . . 15 Principle of Intelligent Shut-Down in the case of transmission node site 19 GSM-LTE RF sharing architecture overview . . . . . . . . . . . . . . . . . . . . . 22 WCDMA-GSM RF sharing architecture overview . . . . . . . . . . . . . . . . . . 23 WCDMA-LTE RF sharing architecture overview. . . . . . . . . . . . . . . . . . . 24 Transport sharing in multiradio BTS site . . . . . . . . . . . . . . . . . . . . . . . . . 25 BTS Site Manager main window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Audit trail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 The RUEM concept. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Isometric view of the System Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Id:0900d805809b557a Confidential DN0971928 Flexi Multiradio 10 Base Station Product Description List of tables Table 1 Table 2 Table 3 Table 4 Table 5 DN0971928 Maximum capacity of Flexi Multiradio 10 Base Station . . . . . . . . . . . . . 27 Flexi BTS naming convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Flexi Multiradio BTS System Module hardware product generations . . 47 Flexi Multiradio BTS RF Module hardware product generations . . . . . 47 Flexi Multiradio BTS Remote Radio Head hardware product generations 49 Id:0900d805809b557a Confidential 5 Flexi RRH 2TX 2100 (FRGV) is LTE-only. Section Intelligent shut-down has been added.Summary of changes Flexi Multiradio 10 Base Station Product Description Summary of changes Changes between document issues are cumulative. The following items have been added to section Appendix Flexi BTS hardware releases: – FRGS – FRHC – FRMC – FRPA – FRPB – FRHF – FZNC – FZHA – FHEB – FRHE – FRHD – FZNI The following items are also available in RL50: FXDA. the latest document issue contains all changes made to previous issues. Id:0900d805809b559a Confidential DN0971928 . RL50 WCDMA Table RU40 RAT releases covered by the document Changes between issues 01B (2013-03-04) and 01C (2013-09-17) • • • • • • Information on FSML and FSMG has been removed from the document. The IP protection level has been updated from IP55 to IP65 in Easy installation. RG30 LTE RL25TD. This document is published with the product releases listed in the following table. Flexi 3U Mounting Covers Front/Back (FMCF) has been replaced by Flexi 3U Mounting Covers Front and Back (FMCA). Sections Construction and Mechanics have been updated accordingly. Therefore. Figure WCDMA-LTE RF sharing architecture overview has been added. Section RSS-310 compliance has been added. Radio Access Technology (RAT) Product release GSM RG20. FXDB. FRGT. RL35TD RL40. Table Flexi Multiradio BTS Remote Radio Head hardware product generations has been updated accordingly. Changes between issues 01A (2012-12-04) and 01B (2013-03-04) • • 6 The document title has been changed to Flexi Multiradio 10 Base Station Product Description (the previous name was Flexi Multiradio 10 BTS Product Description). The title of section Features has been changed to Benefits.Flexi Multiradio 10 Base Station Product Description • • • • • • • • Summary of changes Information on 3-sector 240 W RF Module has been added to One BTS for all network applications. Chapter Appendix Flexi BTS hardware releases has been added. The number of external alarms and controls has been updated in chapter External alarms and controls. Id:0900d805809b559a Confidential 7 . Section Introduction to Flexi Multiradio 10 Base Station has been updated with more detailed information on Flexi Multiradio 10 Base Station. information on 6Tx RF Module has been added. The list of BTS Site Manager supported OSs has been updated in Local Management Tool. Section Remote User Event Log Management has been updated accordingly. (Flexi Multiradio 10 Base Station System Module has six userdefined external inputs and six user-controlled inputs/outputs in the HDMI connector. Capacity values in Baseband capacity have been updated. BTS Site Manager main window figure has been updated in Local Management Tool section. not FTM/FCT. Information on MIBBU (Multi-integrated Battery Back-Up Unit) has been removed from Optional items. Chapter Single RAN aspects has been added. Additionally. Chapter Appendix Flexi abbreviations has been added. operations are logged on FCT.) Chapter System Module has been updated with the list of the available System Modules. Section Active Antenna has been added. Changes between issues 01 (2012-06-26) and 01A (2012-12-04) • • • • • • • • DN0971928 The content and structure of the document have been adjusted to reflect Single RAN aspects. With RUEM. The capacity data of FBBA extension sub-module has been updated. Summary of changes 8 Flexi Multiradio 10 Base Station Product Description Id:0900d805809b559a Confidential DN0971928 . The concurrent mode functionality can include several radio access technologies and their combinations. timing over packet. where several operators can share resources of one BTS. GSM-WCDMA. providing a future-proof platform for advanced radio systems. WCDMA-LTE. which is based on Flexi Multiradio System Module and multiradio-capable RF Module/Remote Radio Head variants. the architecture supports the most common interfaces between the modules and functions as defined by Open Base Station Architecture Initiative (OBSAI) and Common Public Radio Interface (CPRI). and GPS methods. w NOTICE: See roadmaps for CPRI availability. Flexi Multiradio 10 Base Station supports legacy network interface. It supports the following radio access technologies in all needed frequency variants: • • • • GSM/EDGE WCDMA HSPA and HSPA evolution LTE TDD/FDD The architecture supports 3GPP functions and features in 3GPP release 9 and beyond. DN0971928 Id:0900d805809b5586 Confidential 9 . Flexi Multiradio 10 Base Station is a true software-defined multiradio and multicarrier base station that can use all the above mentioned network technologies. Furthermore. The Flexi BTS also supports multioperator cases (MOCN). GSM-WCDMA-LTE. synchronization and timing methods based on synchronous Ethernet. It also fully utilizes Ethernet-based transport with security solutions. either in a dedicated or a concurrent mode of operation.Flexi Multiradio 10 Base Station Product Description Introduction to Flexi Multiradio 10 Base Station 1 Introduction to Flexi Multiradio 10 Base Station This Product Description describes Flexi Multiradio 10 Base Station. Single RAN and LTEAdvanced ready multiradio BTS. for example GSM-LTE. Flexi Multiradio 10 Base Station is a high-capacity. Introduction to Flexi Multiradio 10 Base Station Figure 1 Flexi Multiradio 10 Base Station Product Description General architecture of Flexi Multiradio 10 Base Station See the following documents for more information on Flexi Multiradio 10 Base Station modules and sub-modules: • • • • 10 Flexi Multiradio 10 Base Station System Module Description Flexi Multiradio BTS [technology] RF Module and Remote Radio Head Description Flexi Multiradio 10 Base Station Transmission Description Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description Id:0900d805809b5586 Confidential DN0971928 . Flexi Multiradio 10 Base Station Product Description 1. When the modules are installed without a cabinet. One or two optional Flexi Multiradio 10 BTS Outdoor Capacity Extension SubModules (FBBA). A minimum of one plinth is required for a stack installation and one plinth per two modules in pole and wall installations. One optional Flexi Multiradio 10 BTS Transmission Sub-Module. One optional outdoor-capable Flexi Power Module (FPMA) that can house a maximum of four sub-modules: – One to three optional AC/DC converter sub-modules (FPAA). One optional Flexi Multiradio 10 BTS Power Distribution Sub-Module (FPFD). Flexi Mounting Kit Floor/Wall/Pole for stacked installations (FMFA). the following items are available: • • DN0971928 Flexi 3U Mounting Covers front/back for each module for installations without a cabinet (FMCA). Id:0900d805809b5586 Confidential 11 . mandatory in outdoor installations.1 Introduction to Flexi Multiradio 10 Base Station Construction A typical Flexi Multiradio 10 Base Station consists of the following baseband items: • • • • • One Flexi Multiradio System Module with an integrated Gigabit Ethernet (GE) transport interface. – One to three optional battery sub-modules (FPBA/B). Each module controls its own fans according to temperature information. snow. with installed gaskets in all of the connectors. weather-sealed. This provides fixing points for modules to the plinth and supports the stack of modules. The core mechanics also provide EMC shielding. Fan assembly. and at least IP55 class protected. This provides fresh air to cool the module. and make the module core IP65 weatherproof. Module cables. All cables are IP65 protected. Module casing. The core mechanics. even with one fan. and two redundant fans enable module operation at normal temperatures. shield the module core against water. Optional Front and Back covers (FMCA) for BTS site installations without a cabinet. The fan sub-module can be changed in an operational module at a site where back access is provided.2 Flexi Multiradio 10 Base Station Product Description Mechanics All Flexi Multiradio 10 Base Station modules are outdoor-capable.Introduction to Flexi Multiradio 10 Base Station 1. Flexi Multiradio 10 Base Station modules consist of the following main parts: • • • • • • • • 12 Module core. and solid foreign objects. or Optional Flexi Cabinet for Outdoor (FCOA) or Flexi Cabinet for Indoor (FCIA) or Optional Mounting Shield (FMSA/FMSB) or Optional Flexi Cabinet Outdoor Small (FCOS) Id:0900d805809b5586 Confidential DN0971928 . The module core can be changed even if the module is at the bottom of the module stack. Flexi Multiradio 10 Base Station Product Description RSS-310 compliance 2 RSS-310 compliance This equipment complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. DN0971928 Id:0900d80580a1fad6 Confidential 13 . mercury. The directive applies to the use of lead. hexavalent chromium. cadmium. polybrominated biphenyls (PBB).EU RoHS statement Flexi Multiradio 10 Base Station Product Description 3 EU RoHS statement This equipment complies with the European Union RoHS Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment. and polybrominated diphenyl ethers (PBDE) in electrical and electronic equipment. 14 Id:0900d805809fba8a Confidential DN0971928 . firmware. and hardware) provided and/or supported by Nokia Siemens Networks.Flexi Multiradio 10 Base Station Product Description CE marking 4 CE marking Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive) Hereby. R&TTE Directive 1995/5/EC AT ü FR ü LV ü LI ü BE ü DE ü LT ü RO ü BG ü GB ü LU ü SK ü CY ü GR ü MT ü SI ü CZ ü HU ü NL ü ES ü DK ü IS ü NO ü SE ü EE ü IE ü PL ü CH ü FI ü IT ü PT ü TR ü Figure 2 List of countries respecting EU Directive 1999/5/EC This declaration is only valid for configurations (combinations of software. DN0971928 Id:0900d805809f66ea Confidential 15 . Nokia Siemens Networks declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive: 1999/5/EC. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. pursuant to Part 15 of the FCC Rules. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.FCC Part 15 compliance Flexi Multiradio 10 Base Station Product Description 5 FCC Part 15 compliance This equipment has been tested and found to comply with the limits for a Class B digital device. This equipment generates. uses. 16 Id:0900d80580a0ba94 Confidential DN0971928 . may cause harmful interference to radio communications. Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment. if not installed and used in accordance with the instruction manuals. and can radiate radio frequency energy and. Low acoustic noise The acoustic noise produced by a Flexi Multiradio 10 Base Station site is low because of reduced power consumption and an increased unit integration level. the same equipment can be used to build coverage and capacity. the commissioning wizard produces a BTS Commissioning Report. for instance. With intelligent shut-down. At the end of the process. Flexi Multiradio 10 BTS with battery backup system supports an intelligent BTS site power shutdown procedure in the event of an AC power failure. Installation locations for a Flexi Multiradio 10 Base Station can be smaller than or the same as those reserved for previous Nokia Siemens Networks BTSs. Flexi Multiradio 10 Base Station is designed to utilize the existing site equipment. Reliable operation Simplicity and speed of maintenance improves operational reliability. Easy commissioning The autodetection feature of Flexi Multiradio 10 Base Station makes commissioning and integrating fast and easy. Each Flexi Multiradio 10 Base Station module is protected to at least IP65 level and can be installed as such at an outdoor site. In addition. Flexi Multiradio 10 Base Station can be installed on a wall. Flexi Multiradio 10 Base Station can be installed at any existing legacy GSM/EDGE/CDMA/WCDMA site for a broadband data capability upgrade. A high cell capacity and wide coverage per site means fewer sites which makes building a network more cost-effective.Flexi Multiradio 10 Base Station Product Description Benefits 6 Benefits 6. The commissioning wizard guides the user step-by-step through the whole commissioning process. the operator can define different shutdown timers and priorities for the BTS sectors and carriers. Intelligent shut-down Intelligent shut-down feature optimizes the investment to one battery backup system on a high-capacity BTS. separate backup systems for BTS and transmission are unnecessary. Easy installation A Flexi Multiradio 10 Base Station module can be lifted. it fits in the existing legacy Nokia Siemens Networks GSM/EDGE/CDMA/WCDMA BTS footprints as well. especially on sites that operate as important transmission hub nodes. especially at urban outdoor sites.1 Cost-efficient modular site With Flexi Multiradio 10 Base Station. downtime when a new software package is put into use. compared to traditional cabinet BTSs. reducing. however. Maintenance is improved by module integration and automatic fault detection procedures. both indoor and outdoor cabinet installation options are available. Site acceptance is easier. Special attention has been paid to Flexi Multiradio 10 Base Station software start time. Fan speeds and acoustic noise are adapted to the BTS load and ambient temperature. DN0971928 Id:0900d805809d37c7 Confidential 17 . carried. During the commissioning of each site. and put in place by one person. The average module installation time is reduced. all cells of that BTS will be switched off gracefully. Once the AC power is restored. The second timer can be set to shut down the remaining 1+1+1 BTS (for example) one hour after the AC power failure. Two timers with two different actions are steering the BTS behavior while working on batteries: • • When the first timer is exceeded.an alarm is raised.Benefits Flexi Multiradio 10 Base Station Product Description Intelligent shutdown is activated from Power systems by activating one external alarm (EAC) lines to Flexi BTS. to operate as 1+1+1 (for example) 30 minutes after an AC power failure. In result. and the BTS automatically reduces the required power consumption. means the UEs in that cell will be forced to change to a different cell. a three-sector two-carrier Flexi Multiradio 10 BTS WCDMA (2+2+2) site equipped with battery backup operates as a transmission hub node towards other BTSs in a chain. When Flexi BTS detects a problem with the power provisioning . The first timer can be set to shut down the second carriers of the BTS. For example. Different shutdown scenarios can be configured for the BTS by setting these timers. Flexi BTS is operating with reduced or no service offered as long as there is enough power. Flexi BTS again offers full service. in order to support the transmission node for as long as possible with the existing battery capacity. Timers can be set according to the configuration and priorities of each site. The reduction of power is done via the stepwise shutdown of services which are triggered by operator configurable timers per BTS. The setting especially of the first timer value shall consider the specific situation in the network.so switching to battery power supply . selected number of cells will be switched off (for example 222 to 111) When the second timer is exceeded. 18 Id:0900d805809d37c7 Confidential DN0971928 . The timer values can be configured via NetAct or with BTS SM. keep transmission operational System Module backhaul BTS1 external alarm line DC AC power failure triggers shut down start timers via alarm line AC power Rectifier AC-DC Battery back-up DC Transmission HUB node to other BTSs Figure 3 w DN0971928 backhaul BTS2 Principle of Intelligent Shut-Down in the case of transmission node site NOTICE: See roadmaps for intelligent shut-down availability.Flexi Multiradio 10 Base Station Product Description Benefits RF Module 1st timer expires: shut down sectors or carriers in BTS RF Module RF Module 2nd timer expires: shut down BTS. Id:0900d805809d37c7 Confidential 19 . It offers: • • • • • • w Wide variety of RF modules for different applications and use cases. NOTICE: Masthead amplifier (MHA) is not supported in TD-LTE. for example high downlink power with Flexi 3-sector 240 W RF Module. Antenna line Optimized Antenna line is a separate. It ensures cell ranges that meet the requirements of the coverage applications. High downlink power in small size with Flexi Remote Radio Head. Flexi Multiradio 10 Base Station has been developed for coverage applications. In addition to the flexible traffic capacity.2 One BTS for all network applications Flexi Multiradio 10 Base Station is optimized for high-capacity and wide-coverage applications. 20 Id:0900d80580993e3b Confidential DN0971928 . or jumper cables are necessary between the Flexi Multiradio 10 Base Station antenna connector and the antenna. Depending on network capacity requirements. Flexi Multiradio 10 Base Station also allows a free mix of traffic patterns to accommodate whatever proportion of voice and data is required. enabled by SW licenses: • • • Integrated MHA power feeding and O&M control to the RF Module of the Flexi BTS. Support of 2Tx MIMO 40+40 W per sector with single 6Tx RF Module and 4Tx MIMO 40+40+40+40 W per sector with two 6Tx RF Modules. Flexi RF Module has an integrated lightning protection circuit in all antenna connectors. Integrated Antenna line supervision by Return Loss measurement (VSWR measurement). Therefore. High speed broadband data and high capacity voice Flexi Multiradio 10 Base Station is a compact multi-purpose BTS designed to support all future high speed broadband data and voice services over an air interface. The processing capacity of Flexi Multiradio 10 Base Station can be configured to support the maximum capacity that the air interface allows. A seamless voice and data coverage area can be built easily. Outdoor modules that can be located close to antennas. Flexi Multiradio 10 Base Station Optimized Antenna line includes the following optional features. Integrated 3GPP standard Antenna Tilt power feeding and 3GPP Antenna Tilt O&M control to the RF Module of the Flexi BTS. the capacity installed can be matched with the capacity of the air interface. including 3GPP antenna tilting and masthead amplifier (MHA) support. as well as optimizes RF performance in both the uplink and downlink direction. The antenna connector of Flexi Multiradio 10 Base Station is on the RF Module front panel. the number of sites required for building a good coverage is minimized.Flexi Multiradio 10 Base Station Product Description 6. No additional units. reducing antenna feeder losses. Optimized antenna system performance. Optimum uplink performance and receiver sensitivity. Smooth data and voice capacity evolution is provided through software. optional site solution to additionally improve total BTS and antenna system site RF performance and to minimize costs. That minimizes the antenna line length and losses. connectors. 3 Feederless and Distributed Site concept Standard Flexi Multiradio 10 Base Station modules support the Feederless BTS site application where one RF Module or Remote Radio Head or the entire Flexi BTS is installed close to the antennas. or one sector with 2TX MIMO with optional four-way uplink diversity. In the Distributed Site solution. Easier installation because of reduced cabling to the tower. or three sectors. No masthead amplifiers/tower-mounted amplifiers. RF Module and Remote Radio Head can be software-activated and configured to support one. No long antenna feeders (typically six for a three-sector site). The benefits of Feederless sites are: • • • • • • Better RF performance because there are no downlink and uplink feeder losses. DN0971928 Id:0900d80580a2d987 Confidential 21 . two. Reduced total wind load and weight. traditional long antenna feeders or masthead amplifiers are not needed thanks to which the BTS site RF performance is optimized in both uplink and downlink.Flexi Multiradio 10 Base Station Product Description 6. For a feederless site. RF Module(s) or Remote Radio Head(s) are located up to 20 km away from the main Flexi System Module site. Reduced total power consumption. and provides the operators with future-proof BTS site evolution. BTS resources between RATs are allocated and shared by allowing two Flexi EDGE/WCDMA/LTE System Modules to share the same Flexi BTS Multiradio RF Module or Remote Radio Head (RRH).1 RF sharing The RF sharing feature allows Flexi Multiradio BTS RF Module to operate in a concurrent mode with two radio access technologies (RATs). RF Module or RRH is transmitting RF carrier signals for two or more RATs at the same frequency band. The RF Sharing concept simplifies the antenna system complexity.Single RAN aspects Flexi Multiradio 10 Base Station Product Description 7 Single RAN aspects 7. LTE management GSM management NetAct iOMS NWI3 Q3/XML BTS O&M S1/IP Flexi BSC OMU Abis TDM/IP eNB BCF Flexi Multiradio BTS GSM RP3-01 Flexi Multiradio BTS LTE RP3-01 RFM Figure 4 22 RP3-01 RFM RFM GSM-LTE RF sharing architecture overview Id:0900d80580a23a43 Confidential DN0971928 . Flexi Multiradio 10 Base Station Product Description Single RAN aspects WCDMA management GSM management NetAct OMS NWI3 Q3/XML BTS O&M Flexi BSC RNC OMU Iub/BTS O&M Abis TDM/IP BCF Flexi Multiradio BTS GSM RP3-01 Flexi Multiradio BTS WCDMA RP3-01 RFM Figure 5 DN0971928 RP3-01 RFM RFM WCDMA-GSM RF sharing architecture overview Id:0900d80580a23a43 Confidential 23 . see: • • • • • • • • 7.Single RAN aspects Flexi Multiradio 10 Base Station Product Description WCDMA management LTE management NetAct iOMS OMS NWI3 NWI3 BTS O&M BTS O&M S1/IP RNC Iub/BTS O&M eNB Flexi Multiradio BTS LTE RP3-01 Flexi Multiradio BTS WCDMA RP3-01 RP3-01 RFM Figure 6 RFM WCDMA-LTE RF sharing architecture overview For more information. 24 Id:0900d80580a23a43 Confidential DN0971928 . Note that multiple Flexi Multiradio 10 System Modules are required.2 RF Sharing Operability Configuring and Upgrading GSM-LTE RF Sharing Creating RF Sharing LTE-GSM Configurations Configuring WCDMA-GSM RF Sharing Creating RF Sharing WCDMA-GSM Configurations Configuring WCDMA-LTE RF Sharing Creating RF Sharing WCDMA-LTE Configurations Flexi Multiradio BTS RF Sharing Supported Configurations (Excel) Transport backhaul sharing Transport backhaul sharing provides the possibility for a Single RAN site to be connected to the backhaul network with just one physical Ethernet connection. g Ethernet switching is required at the BTS where the layer 2 traffic aggregation/daisy chain is to be implemented. Synchronization Hub feature can be used for reference clock distribution on the BTS site. Synchronization Hub Each System Module can act as a synchronization hub for other near-located System Modules.and QoS-aware. One of the interfaces is used for the backhaul connection.048 MHz SynchOut based on any available synchronization source. Additionally. then they can also be used for synchronization distribution to other devices. The Ethernet switch is VLAN. The egress traffic of the switch can be shaped to meet the bandwidth limitations of the backhaul network. QoS Aware Ethernet Switching QoS Aware Ethernet Switching allows multiple Ethernet interfaces in the BTS to be connected through the integrated Ethernet switch. If PDH interfaces are available in the System Module. while others might be used to connect other BTSs (at the same or another site). a policy can be applied to the ingress traffic to protect the BTS from the interface overload. DN0971928 Id:0900d80580a23a43 Confidential 25 . it can output 2. It is also possible to daisy chain several network devices.Flexi Multiradio 10 Base Station Product Description Single RAN aspects SAE-GW MME RNC BSC S1/X2 Iub Packet Abis System Module LTE S1/X2 IP System Module WCDMA Iub IP System Module GSM Packet Abis IP Ethernet IP Ethernet IP / Ethernet Multiradio BTS site Figure 7 Transport sharing in multiradio BTS site The BTS site backhaul traffic can be aggregated on one integrated IP/Ethernet interface by utilizing integrated QoS aware Ethernet switching. For example. the BTS Oven Controlled Crystal Oscillator (OCXO) keeps running with the last known control value. and still provides the sync output. 26 Id:0900d80580a23a43 Confidential DN0971928 . Then. it switches to hold-over mode.Single RAN aspects Flexi Multiradio 10 Base Station Product Description If the BTS loses all sync sources. see Commissioning Flexi Multiradio BTS [technology]. Flexi Multiradio 10 Base Station baseband capacity can be optimized in steps of Mbit/s without a site visit. Table 1 Maximum capacity of Flexi Multiradio 10 Base Station shows radio access technology–specific capacity details. making it possible to build high capacity sites. The Flexi BTS architecture supports baseband pooling of two System Modules. GSM/EDGE 216 transceivers WCDMA Approximately 3 Gbps with chaining configuration LTE 900 Mbps downlink and 300 Mbps uplink Table 1 Maximum capacity of Flexi Multiradio 10 Base Station For information on licensing. DN0971928 Id:0900d80580a23af6 Confidential 27 .Flexi Multiradio 10 Base Station Product Description Baseband capacity 8 Baseband capacity Baseband capacity by SW license Future-proof Flexi Multiradio System Module capacity is designed to support flexible and cost-optimized site capacity evolution. Flexi Multiradio System Module provides space for up to two baseband extension sub-modules (FBBA) that enable three times the capacity of the Flexi Multiradio System Module. Baseband extension and related interface utilization depends on the radio access technology and the use case (a pure new Flexi Multiradio System Module case or an existing Flexi System Module case). The highest capacity Flexi System Module is dimensioned to provide a hardware baseband capacity. Baseband capacity of Flexi Multiradio 10 Base Station can be optimized depending on the BTS configuration and required traffic capacity of the BTS site. More baseband capacity can be allocated remotely from NetAct™ by sending a Baseband SW License to Flexi Multiradio 10 Base Station. Future capacity evolution Flexi Multiradio 10 Base Station is future-proof designed to support future capacity demand. for example. SRIO and OBSAI RP3-01 interfaces provide connectivity for baseband capacity and/or technology extension. for up to three 20 MHz LTE cells (FSMF). supervision. Id:0900d80580993e71 Confidential DN0971928 . maintenance. FlexiTransport Manager. The site manager software package includes the following: • • • 28 Flexi Multiradio BTS Manager. Site Support Manager.1 Local Management Tool The BTS Site Manager software is used to manage Flexi Multiradio 10 Base Station commissioning. including antenna line and antenna equipment control and management. for transmission management. for power and battery backup system. and testing. as well as transmission configuration.Management and software Flexi Multiradio 10 Base Station Product Description 9 Management and software 9. Figure 8 BTS Site Manager main window A Flexi Multiradio 10 Base Station site can be controlled remotely by opening a BTS Site Manager session at a remote NetActTM site. and 7 (32/64 bits) Microsoft Windows Server 2003 and 2008 Red Hat Enterprise Linux 4 ES GNOME desktop Id:0900d80580993e71 Confidential 29 . BTS Site Manager runs in the following environments: • • • DN0971928 Microsoft Windows XP. The manager PC is connected to the BTS by means of an Ethernet connection.Flexi Multiradio 10 Base Station Product Description Management and software These managers are integrated so that the physical interface (cable and connectors) is the same in all three cases. Vista. however. three different applications run on the PC. Flexi Multiradio 10 Base Station Product Description 9. a polling process is used to check possible changes in the BTS configuration. the information in the hardware database changes.2 Configuration management Once the BTS is in normal operation. 30 Id:0900d80580988f69 Confidential DN0971928 . When modules are added to or removed from the BTS. NWI3 logged operations: • • • • Login attempts (successful and unsuccessful) Logout Configuration changes (on fragment level) Local account updates HTTP logged operations: • • Reboot operations Reset to factory default operation XoH logged operations: • • • • • • • • 9. In both cases this is logged.how does it work? RUEM correlates every management operation with each user: • • DN0971928 NWI3 and XOH management operations implement session concept (username/password) HTTP operations which are logged are operations that require username/password Id:0900d80580993ebf Confidential 31 .3 Remote User Event Log Management Remote User Event Log Management (RUEM) is a feature that allows a network management system (NMS) to trace operations done in network elements (NEs) by different users. This functionality is sometimes called “Audit Trail”.1 SW Management (SW update Request and SW interrupt) Object Configuration Management (for example ResetRequest) Licence Update/Deletion Request Alarm Management and Diagnostics (for example Change Direct Access Status) Test Management (for example Test Dedicated State Request) User Management (for example Login and Modify User Request) Commissioning (for example Parse Commissioning Data Request) Clock Operation Request RUEM concept . operations are logged on Flexi Baseband Controller (FCT) and sent to NetAct within one single RUEM log file.Flexi Multiradio 10 Base Station Product Description 9. Figure 9 Audit trail With RUEM.3. User access and operations might be successful or fail. Triggered by NetAct 2. The RUEM upload mechanism 1. the read logfile is deleted from the BTS to free memory space for next log entries.Watermark Operations that are logged by RUEM are stored in FCT in a ring buffer (internally). ~70% of total buffer size) is reached. and thus data is not lost upon power breaks. Triggered by Network element (FCT) .Flexi Multiradio 10 Base Station Product Description Figure 10 The RUEM concept Notification . This buffer is filled up for each logged operation.if the Watermark level is reached After a successful reading of the logfile by the NMS. Log files in the BTS are kept in nonvolatile memory. FCT will send a notification to NetAct (mediated by OMS in Flexi). 32 Id:0900d80580993ebf Confidential DN0971928 . As soon as a critical value (that is watermark. It is not recoverable. This special event is called a wrapped-over event. This should be logged in RUEM log file.Flexi Multiradio 10 Base Station Product Description Exception: In case NetAct still does not upload the RUEM log file. DN0971928 Id:0900d80580993ebf Confidential 33 . the buffer might fill up to its maximum size and even exceed this. In the latter situation the buffer has an overflow and some old information gets lost permanently. Either of these software versions can be activated at any time. Flexi Multiradio 10 Base Station keeps the current and previous software packages in its flash memory. with the BTS Site Manager software. Flexi Multiradio 10 Base Station only uses downloadable software. The software can be loaded either locally. Reboot is required in order to put the software into use. This procedure is centralized. Reboot is required in order to put the software into use. meaning that several BTSs can be upgraded with the new software either simultaneously or one by one. or remotely from NetActTM. All software can be downloaded and updated from NetActTM.4 Software updates Flexi Multiradio 10 Base Station can store two software packages in its memory. Site visits are unnecessary for routine operation and maintenance (O&M) tasks. Typically. The RF Module and RRH SW is updated automatically during Flexi Multiradio 10 Base Station SW update. during the commissioning process. 34 Id:0900d80580993ecb Confidential DN0971928 . Updated software (current and previous) in the BTS can be seen through BTS Site Manager/NetActTM. The new software can be activated at any time.Flexi Multiradio 10 Base Station Product Description 9. Flexi Multiradio 10 Base Station software can be downloaded as a background operation without interrupting the BTS operation. for example. local software download is done only when the NetActTM connection is missing. the external alarms and control outputs of the BTS are managed from NetActTM after they have been configured. In normal operation.Flexi Multiradio 10 Base Station Product Description 9. Six user-defined external inputs and six usercontrolled inputs/outputs are available and can be freely configured to support various observation or control needs at the BTS site. DN0971928 Id:0900d80580993ed1 Confidential 35 .5 External alarms and controls BTS inputs and outputs can be configured and tested locally at the BTS site with Flexi Multiradio BTS Site Manager software. The following Flexi Multiradio System Module is available: • FSMF .Modules Flexi Multiradio 10 Base Station Product Description 10 Modules 10. see Flexi Multiradio 10 Base Station System Module Description.high capacity GSM/WCDMA/LTE System Module For more detailed information on the System Module. The architecture of Flexi Multiradio System Module enables utilization of several System Module and sub-module variants. The System Module consists of a casing with the following baseband modules: a core module and up to two optional capacity extension sub-modules. 36 Id:0900d80580a22a75 Confidential DN0971928 .1 System Module Figure 11 Isometric view of the System Module Flexi Multiradio System Module is fully OBSAI compatible and has all the control and baseband functions for the supported radio access technologies. 2 RF Module There are different types of RF Modules available. RF Modules can be used in stack. pole.Flexi Multiradio 10 Base Station Product Description 10. DN0971928 Id:0900d80580993ed7 Confidential 37 . indoors or outdoors. Flexi RF Module can support up to three sectors. They can be easily installed outdoors close to antennas. see Flexi Multiradio BTS [technology] RF Module and Remote Radio Head Description. and wall installations. For more detailed information on a particular RF Module. see Flexi Multiradio BTS [technology] RF Module and Remote Radio Head Description. 38 Id:0900d80580988e98 Confidential DN0971928 . The Remote Radio Head (RRH) can support one sector with the following integrated features: • • • • • • • • High output power at antenna connectors Two linear power amplifiers Two RF filters for TX/RX Two-way RX diversity Wide bandwidth support (up to 35 MHz depending on 3GPP band RF variant) A 48 V DC input power supply No fans Two OBSAI optical interfaces For more detailed information on a particular Remote Radio Head.Flexi Multiradio 10 Base Station Product Description 10. Remote Radio Heads are mainly used in outdoor pole installations where support for one sector is needed.3 Remote Radio Head There are different types of Remote Radio Heads available. It can also be used in combination with the traditional Flexi RF units. see Flexi Multiradio Antenna System Product Description.Flexi Multiradio 10 Base Station Product Description 10.4 Active Antenna Flexi Multiradio Active Antenna is an alternative to RF Modules/Remote Radio Heads. 2x2 Multiple Input Multiple Output (MIMO) and independent Tx and Rx electrical tilting per frequency or RAT. w DN0971928 NOTICE: See roadmaps for Active Antenna availability. For more information on Active Antenna. The radio frequency elements of the BTS are integrated into the antenna. Flexi Multiradio Active Antenna increases site capacity and coverage with features such as vertical beamforming. Id:0900d80580993ed9 Confidential 39 . Flexi Power AC/DC Sub-Module (FPAA) The main function of Flexi Power AC/DC Sub-Module (FPAA) is to provide the BTS modules with 48 V DC power from an AC supply. It is a stand-alone external 19-inch wide 2U high outdoor module. 40 Id:0900d80580a2d993 Confidential DN0971928 . Flexi Multiradio 10 BTS Power Distribution Sub-Module (FPFD) The optional integrated outdoor Flexi Power Distribution Sub-Module (FPFD) is a sizeoptimized power distribution unit that has basic overvoltage protection (type approval level with 2kV/1kV). general-purpose outdoor PDU module with Class II overvoltage protection with a 15 kA protection level. RRHs. but it can also be used for distributed BTS configurations in the same way as the existing Flexi BTS integrated power distribution sub-module with an optional FSEC or FSES. When dedicated for LTE (FDD or TDD). It is installed inside an outdoor 3U casing. One FBBA brings additional 576 CEs for WCDMA. Flexi Power Distribution Module (FPFC) The optional Flexi Power Distribution Module (FPFC) is a stand-alone. For GSM/EDGE. Up to two FBBAs are supported per one Flexi Multiradio System Module.5 Optional items Flexi Multiradio 10 BTS Outdoor Capacity Extension Sub-Module (FBBA) Flexi Multiradio 10 BTS Outdoor Capacity Extension Sub-Module (FBBA) provides additional capacity to the BTS. for example. Internal connections between the core module and FTIF go through an internal connector. It has one external alarm to indicate OVP condition. It can also be used. It is designed to be used for stacked configurations. it supports 72 GSM carriers. The FPFD provides four external 48 V DC outputs for Flexi Modules (RF Module. up in the tower to divide one main DC line to several RFM/RRHs. that is single carrier transceivers (TRX). HSPA performance is 756 Mbps for downlink and 157 Mbps for uplink. and internal connections between the core module and FPFD go through an internal connector. each of them having an output power of 1 kW 48 V DC. the FTIF supports powering FlexiPacket Radio over the Ethernet link. and a support frame for the actual power sub-modules (FPAA and FPBA/B). and extension System Module) or any standard 48 V DC device at the site. When operated in a 100/1000Base-T mode. DC cable set. and extension System Module) or any standard -48 V DC device at the site. It feeds 48 V DC power to distributed Flexi RF Modules or Remote Radio Heads without an external protection unit (FSEC or FSES) when the FPFC is installed close to an RF Module (maximum 4 m away). The FPMA can house up to four AC/DC rectifiers. RRH. The FPFC provides six outputs for Flexi Modules (RF Modules. it supports capacity of 3x20 MHz (or 6x10 MHz) with MIMO enabling 450 Mbps downlink and 150 Mbps uplink data speeds.Flexi Multiradio 10 Base Station Product Description 10. Flexi Multiradio 10 BTS Transmission Sub-Module (FTIF) Flexi Multiradio 10 BTS Transmission Sub-Module (FTIF) has 8 E1/T1/JT1 interfaces and two Gigabit Ethernet Combo ports. Flexi Power Module (FPMA) Flexi Power Module (FPMA) includes an AC connection box. battery backup time is up to 30 minutes for a typical 1+1+1 configuration when three new FPBA/Bs are in use. Flexi Power Rectifier (FPRx) Flexi Power Rectifier (FPRx) is a modular 6 kW output power AC rectifier package made up of three individual 2 kW AC/DC power modules operating in a parallel mode configuration. Flexi Power DC/DC Module 24V (FPDA) The function of Flexi Power DC/DC Module 24V (FPDA) is to generate BTS internal 48 V DC power from an external 24 V DC supply. The FPMA can house up to three battery submodules. The outdoor cabinet can also be used in indoor locations where a locked cabinet for the BTS and other site equipment is needed. The FPDA is a stand-alone 2 kW DC/DC converter with 2U height. The optional indoor cabinet can include the following optional items: • • • • • DN0971928 Flexi Power Rectifier (FPRx) Fire detector (FCDA) EAC IP55 connection box (FSEB) OVP IP55 connection box (FSEC) OVP IP65 connection box (FSES) Id:0900d80580a2d993 Confidential 41 . pole and wall configurations). and stack. The multipurpose cabinet includes a lock and a door alarm switch that is connected to the System Module EAC connector. When the AC power mains is down on a Flexi BTS site. Flexi Cabinet for Indoor (FCIA) Flexi Cabinet for Indoor (FCIA) is an optional sales item for new indoor sites where a cabinet is needed. The optional outdoor cabinet can include the following optional items: • • • • • • • w Outdoor Site Support Module (FCSA) Flexi Power Rectifier (FPRx) Air filter (FCFA) Fire detector (FCDA) EAC IP55 connection box (FSEB) OVP IP55 connection box (FSEC) OVP IP65 connection box (FSES) NOTICE: FSEC is not supported in TD-LTE. It supports Flexi BTS Multiradio configurations (indoor and outdoor cabinets. Flexi Cabinet for Outdoor (FCOA) Flexi Cabinet for Outdoor (FCOA) is an optional sales item for new sites where a cabinet is needed. The FPRx outputs a positive earthed –54V DC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. The FCOA provides IP65 weather protection.Flexi Multiradio 10 Base Station Product Description Flexi Power Battery Sub-Module (FPBA/B) Flexi Power Battery Sub-Module (FPBA/B) is a separate optional sub-module used together with the AC/DC Module (FPAA). The FMSA provides IP65 weather protection for two 3U modules and the FMSB for six 3U modules. Flexi Mounting Kit for Floor. it provides power for the fire detector (FCDA). Flexi Cabinet Outdoor Small (FCOS) Flexi Cabinet Outdoor Small (FCOS) is an IP55-rated outdoor cabinet that provides space of 8U for installing IP20-rated units. The following are installation options for Flexi Cabinet Outdoor Small (FCOS): • • • • • • Stand-alone floor installation On top of a Flexi BTS module stack Wall installation Pole installation Inside Flexi Cabinet for Outdoor (FCOA) 19-inch rack installation Flexi Mounting Kit for Floor. An optional plinth is used to fix Flexi modules to floor. Id:0900d80580a2d993 Confidential DN0971928 . It is also used for altering the DC cable diameter. Flexi Mounting Shield (FMSA/FMSB) Flexi Mounting Shield is a cabinet solution for the Flexi BTS. Wall and Pole (FMFA) Flexi Mounting Kit for Floor. for example. Wall and Pole (FMFA) is an optional item that is used for installing Flexi modules on the floor. wall. In outdoor applications. The FSEB enclosure provides an IP55 weather-protected space for external alarms and controls. Flexi System External OVP (FSEC/FSES) Flexi System External OVP (FSEC/FSES) protects Flexi Multiradio modules against surge pulse(s) in power feeding lines. the enclosure is attached in the proximity of the modules. it is installed on the outdoor cabinet roof. wall. Furthermore.Flexi Multiradio 10 Base Station Product Description w NOTICE: FSEC is not supported in TD-LTE. Flexi System External Alarm (FSEB) Flexi System External Alarm (FSEB) is used as an external alarm control (EAC). w 42 NOTICE: FSEC is not supported in TD-LTE. In indoor or stacked applications without a cabinet. or pole. or pole. on a wall. Wall and Pole (FMFA). 6 External interfaces For full description of the System Module interfaces. see System Module interfaces in Flexi Multiradio 10 Base Station System Module Description. For full description of the transmission interfaces.Flexi Multiradio 10 Base Station Product Description 10. see Flexi Multiradio 10 Base Station Transmission Description. see RF Module interfaces and Remote Radio Head interfaces in Flexi Multiradio BTS [technology] RF Module and Remote Radio Head Description. For full description of the RF Module/RRH interfaces. DN0971928 Id:0900d805809a4bce Confidential 43 . 2000 MHz _B__ Baseband Extension Modules _C__ Cabinet and Cabinet Accessories The general naming is FCxy.outdoor version _C__ Repeater Interface Modules _D__ Diplexers _L__ Low-noise Mast Head Amplifiers _M__ Mounting Kits _O__ Optical distribution unit _P__ Power supply modules and sub-modules or installation kits Table 2 44 Flexi BTS naming convention Id:0900d805809bf896 Confidential DN0971928 .700 MHz upper C .Fxxx.1800 MHz and 1700 MHz F .400 MHz B .900 MHz E . Table Flexi BTS naming convention shows the explanation of the format.850 MHz D . g Table Flexi BTS naming convention might not list all the possible variants/items.2100 MHz H .indoor version O . where x indicates: • • I . some items might not be available in certain releases.Appendix Flexi abbreviations Flexi Multiradio 10 Base Station Product Description 11 Appendix Flexi abbreviations The naming of the Flexi BTS family has the following format . where x indicates: • • • • • • • • • A . Letter Description First letter F___ Flexi family Second letter _A__ Antenna Equipment and Same Band Combiner The general naming is FAxy. Additionally.2600 MHz J .1900 MHz G . Flexi Multiradio 10 Base Station Product Description Letter Appendix Flexi abbreviations Description _R__ Radio Modules _X__ The general naming is: _Z__ • • • FRx_ .850 MHz D . C.S .1900 MHz G .Flexi System External OVP Flexi BTS naming convention (Cont.900 MHz E .Flexi RF Multiradio FZx_ .Flexi Multiradio BTS F . D. where x indicates: • • Table 2 DN0971928 B . Flexi System External OVP The general naming of the modules is FSEx.800 MHz EU N .700 MHz lower M . where x indicates: • • B.Flexi Multiradio 10 BTS Flexi System External Alarm.Flexi TD-LTE RF Module Where x indicates: • • • • • • • • • • • • • • _S__ A .2000 MHz K .2100 MHz H .1500 MHz L .2300 MHz System Modules The general naming of the System Modules is FSMx.1700 Mhz and 2100 MHz J .2600 MHz I .Flexi RF Module FXx_ .700 MHz upper C .) Id:0900d805809bf896 Confidential 45 .Flexi System External Alarm C. E .400 MHz B .1800 MHz and 1700 MHz F . Appendix Flexi abbreviations Flexi Multiradio 10 Base Station Product Description Letter Description _T__ Transport modules. y indicates the module and interface type.Flexi Multiradio BTS transport sub-modules. Fourth letter ___x Table 2 46 Indicates the version .PDH module with 8 E1/T1/J1 interfaces. B. RF Module. RRH. – O .) Id:0900d805809bf896 Confidential DN0971928 . z indicates the module version: – A.MWR IDU module with FlexBus interfaces.the next ones. – F . – F.Hybrid module with PDH symmetrical and Ethernet interfaces. B.Optical interface module with STM1/OC3 interface. _I__ The general naming of the transport modules is Fxyz.A is the first one. C. Flexi BTS naming convention (Cont. Mast Head Amplifiers).. C… . AAS. – J . G… . where: • • • _Y__ x indicates either outdoor (T) or indoor (I) version of the Flexi Multiradio System Module. or frequency band (for example..Hybrid module with PDH asymmetrical and Ethernet interfaces. usage. sub-modules and cables. – I . for example: – P . Global Navigation Satellite System (GNSS) receiver Flexi GPS Surge Protection Kit Third letter __x_ Application.Flexi Multiradio 10 BTS transport sub-modules. . 0) Table 3 Module variant Abbreviation Flexi Multiradio BTS System Module hardware product generations Release 1 HW Release 2 HW Release 3 HW WCDMA release LTE release Flexi RF Module 850 Dual 50 W FRCA x - - RAS5.1 N/A Flexi RF Module 1900 Single 50 W FRFB x - - RAS5.1 N/A Flexi RF Module 2100 Dual 50 W FRGC x - - RAS05 N/A Flexi RF Module 2100 Single 50 W FRGD x - - RAS05 N/A Flexi Compact RF Module 2.1 N/A Flexi RF Module 1900 Dual 50 W FRFA x - - RAS5.Flexi Multiradio 10 Base Station Product Description Appendix Flexi BTS hardware releases 12 Appendix Flexi BTS hardware releases Module variant Release 1 HW Release 2 HW Release 3 HW WCDMA release LTE release FSMB x - - RAS06 N/A FSMC - x - RU20 on top N/A FSMD - x - RU10 RL30 FSME - x - RU10 RL10 FSMF - - x RU30 on top (WN7.1 N/A Flexi RF Module 900 Single 50 W FRDB x - - RAS5.0 2.1 Single 40 W FRGI x - - RAS5.1 N/A Flexi RF Module 850 Single 50 W FRCB x - - RAS5.1 N/A Flexi RF Module 900 Dual 50 W FRDA x - - RAS5.0) RL40 RU40 on top (WN8.1 N/A Flexi RF Module 2100 Dual 50 W FRGJ x - - RAS06 N/A Flexi RF Module 2100 Single 50 W FRGK x - - RAS06 N/A Flexi RF Module 2100 Dual 50 W FRGL x - - RAS06 N/A Flexi RF Module 2100 Single 50 W FRGM x - - RAS06 N/A Table 4 DN0971928 Flexi Multiradio BTS RF Module hardware product generations Id:0900d80580a234e4 Confidential 47 . 1 FRIE - x - RU20 on top RL10 Flexi 3-sector RF Module 1500 FRKA - x - RU20 Flexi 3-sector RF Module 850 FXCA - x - RU20 on top RL20 Flexi 3-sector RF Module 850 FXCB - - x RU40 Flexi 3-sector RF Module 900 FXDA - x - RU20 on top RL50 Flexi 3-sector RF Module 900 FXDB - x - RU30 EP2 Flexi 3-sector RF Module 900 FXDJ - x - RU20 on top N/A Flexi 3-sector RF Module 1800 FXEA - x - RU40 RL20 Flexi 3-sector RF Module 1800 FXEB - x - RU50 RL40 Flexi 3-sector RF Module 1900 FXFA - x - RU20 on top RL40 Flexi 3-sector RF Module 1900 FXFC - - x RU40 N/A Flexi 3-sector RF Module 2100 FRGT - - x RU40 RL50 Flexi RF Module 2TX 850 FXCC - x - N/A RL30 Flexi 3-sector RF Module 2600 FRHA - x - N/A RL10 Flexi 3-sector RF Module 760 FRBB - x - N/A RL30 Table 4 48 N/A N/A RL50 Flexi Multiradio BTS RF Module hardware product generations (Cont.1 Single 50 W FRIB x - - RAS05 N/A Flexi RF Module 2000 Dual 50 W FRJA x - - RAS06 N/A Flexi RF Module 2000 Single 50 W FRJB x - - RAS06 N/A Flexi 3-sector RF Module 2100 FRGF - x - RU10 N/A Flexi 3-sector RF Module 2100 FRGP - x - RU20 on top RL10 Flexi 3-sector RF Module 1.7/2.7/2.Appendix Flexi BTS hardware releases Module variant Flexi Multiradio 10 Base Station Product Description Abbreviation Release 1 HW Release 2 HW Release 3 HW WCDMA release LTE release Flexi RF Module 1.) Id:0900d80580a234e4 Confidential DN0971928 .1 Dual 50 W FRIA x - - RAS05 N/A Flexi RF Module 1.7/2. 1 FRIG - x - N/A RL40 Table 5 DN0971928 Flexi Multiradio BTS Remote Radio Head hardware product generations Id:0900d80580a234e4 Confidential 49 .7/2.Flexi Multiradio 10 Base Station Product Description Module variant Abbreviation Appendix Flexi BTS hardware releases Release 1 HW Release 2 HW Release 3 HW WCDMA release LTE release Flexi 3-sector RF Module 800EU FRMA - x - N/A RL10 Flexi 3-sector RF Module 800 FRMD - x - N/A RL40 Flexi 3-sector RF Module 2100 FRGS - - x N/A RL50 Flexi RF Module 6TX 2600 FRHC - - x N/A RL50 Flexi RF Module 6TX 800 FRMC - - x N/A RL50 Flexi RF Module 6TX 700 FRPA - - x N/A RL50 Flexi RF Module 6TX 700 FRPB - - x N/A RL50 Flexi RF Module 6TX 2600 FRHF - - x N/A RL50 Flexi RF Module 6 x 10 W 2300 FZNC - - x N/A RL25 Flexi RF Module 8 x 10 W 2600 FZHA - - x N/A RL25 Table 4 Flexi Multiradio BTS RF Module hardware product generations (Cont.) Module variant Abbreviation Release 1 HW Release 2 HW Release 3 HW WCDMA release LTE release Flexi RRH 2TX 850 FHCD - x - RU50 N/A Flexi RRH 2TX 900 FHDA - x - RU30 EP1 N/A Flexi RRH 2TX 900 FHDB - x - RU40 RL40 Flexi RRH 2TX 1800 FHEA - x - RU50 RL20 Flexi RRH 2100 Single 70W FRGG x - - RU20 on top N/A Flexi RRH 2TX 2100 FRGQ - x - RU20 on top RL30 Flexi RRH 2TX 2100 FRGV - x - N/A RL40 Flexi RRH 2TX 1900 FHFA - x - RU50 N/A Flexi RRH 4TX 1. ) Id:0900d80580a234e4 Confidential DN0971928 .Appendix Flexi BTS hardware releases Module variant Abbreviation Flexi Multiradio 10 Base Station Product Description Release 1 HW Release 2 HW Release 3 HW WCDMA release LTE release Flexi RRH 2TX 850 FHCA - x - N/A RL30 Flexi RRH 2TX 2600 FRHB - x - N/A RL30 Flexi RRH 2TX 1800 FHEA - x - N/A RL10 Flexi RRH 2TX 730 FRLB - x - N/A RL20 Flexi RRH 2TX 800EU FRMB - x - N/A RL10 Flexi RRH 2TX 1800 FHEB - - x N/A RL50 Flexi RRH 4TX 2600 FRHE - - x N/A RL50 Flexi RRH 4TX 2600 FRHD - - x N/A RL50 Flexi RRH 4TX 2300 FZNI - - x N/A RL25 Table 5 50 Flexi Multiradio BTS Remote Radio Head hardware product generations (Cont.
Copyright © 2024 DOKUMEN.SITE Inc.