SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM SPECIFICATIONCONTENTS Section 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12 13. Scope Basis Additional Requirements Table Table 1, Plates Table 2, Pipes Table 3, Tubes Table 4, Forging Table 5, Castings Table 6, Bolts and Nuts Table 7, Bars and Shapes Table 8, Piping Fittings Table 9, Nonferrous Materials 1. SCOPE This specification lists the Japanese Standard (JIS, JPI),British Standard (BS), and Deutshe Industrie Normen (DIN) substitutes for ASTM Specifications relating to materials for plates, pipes, tubes, forging, castings, bolts and nuts, bars and shapes, piping fittings, and nonferrous materials, in general use. 2. BASIS These substitutes are not necessarily identical to the ASTM Specifications, but are equal in terms of alloy content and have a nearly equal or higher ultimate tensile strength; exceptions to this are underlined. 3. ADDITIONAL REQUIREMENTS The requirements of the ASTM Specifications not covered by the substitute specifications are noted in the Tables, with footnotes given on Section 4. 4. TABLE Substitute materials are shown in the following Tables 1 to 9. STANDARD SPECIFICATION Table 1 PLATE ASTM A-36 Structural Steel JIS BS DIN G 3101 SS400 G 3105 SM400A 4360 Gr 40A (1) 4360 Gr 438 (1) 17100 St44-2 17100 St44-3 A-131 Structural Steel for Ships Gr A Gr B Gr CS Gr D Gr E G 3106 SM400A G 3106 SM400B G 3105 SM400CN G 3105 SM400C (2) G 3105 SM40OCN 4360-40B 4360-40B 4360-40E 4360-40E 4360-40E 17100 St44-3 --------- A-167 Stainless arid Heat-Resisting Chromium,-Nickel Steel Plate, Sheet, and Strip Type 302 Type 304 G 4304 SUS302 (3) G 4304 SUS304 (3) 17440/1 X10CrNiS189 17440/1 X5CrNi1810 Type 304L G 4304 SUS304L (3) Type 310S G 4304 SUS310S (3) Type 316 G 4304 SUS316 (3) Type 316L G 4304 SUS316L (3) Type 321 G 4304 SUS321 (3) Type 347 G 4304 SUS347 (3) --1449-304S31 1501-304S15 1501-304S12 1449-304S11 1501-310S24 1449-310S24 1501-316S16 1449-316S31 1501-316S12 1449-316S11 1501-321S12 1449-321S31 1501-347S17 1449-347S31 17440/1 X2CrNi1911 ----17440/1 X5CrNiMo17122 17440/1 X2CrNiMo17132 17440/1 X6CrNiTi1810 17440/1 X6CrNiNb1810 Note (1): Specify mechanical properties, test and inspection in accordance with ASTM. Note (2): Plates over 1-3/8 Inches (35 m-n) in thickness shall be normalized. Note (3): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G 4307, respectively. STANDARD SPECIFICATION ASTM A-176 Stainless and Heat Resisting Chromium Steel Plate, Sheet, And Strip Type 403 JIS G 4304 SUS403 (1) Type 405 G 4304 SUS405 (1) Type 410 Type 4105 BS DIN G 4304 SUS410 (1) G 4304 SUS410S (1) 14-09-403 S17 S2) 1501-403 S17 l2) 1449-405 S17 1501-405 S17 1449-410 S21 --- ----17440/1 X6CrAl13 --17440/1 X10Cr13 17440/1 X6Cr13 G 3127 SL2N255 G 3127 SL3N255 G 3127 SL3N275 G 3127 SL3N440 --1501-503 ----- ----17280 10Ni14 --- G 3103 S64SOM --- Gr B Gr C G 3103 SB48M --- ----- SEL 16 Mo5 17155 15 Mo3 SEL 16 Mo5 --- A-240 Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels Type 304 Type 304H Type 304L Type 316 G 4304 SUS304 (1) --G 4304 SUS304L (1) G 4304 SUS316 (1) 1501-304S15 1501-304S49 1501-304S12 1501-316S16 Type 316H Type 316L --G 4304 SUS316L (1) 1501-316S49 1501-316S12 Type 317 Type 317L G 4304 SUS317 (1) G 4304 SUS317L (1) --- A-203 Pressure Vessel Plates, Alloy Steel, Nickel Gr A Gr D Gr E Gr F A-204 Pressure Vessel Plates, Alloy Steel, Molybdenum Gr A Note (1): Note (2): 17440/1 X5CrNi1810 --17440/1 X2CrNi1911 17440/1 X5CrNiMo17122 --17440/1 X2CrNiMo17132 17440/1 X2CrHiMo18164 For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307, respectively. Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM. STANDARD SPECIFICATION ASTM Type 321 Type 321H Type 347 Type 347H Type 405 Type 410 Type 410S Type 430 A-263 Corrosion-Resisting Chromium Steel-Clad Plate, Sheet, and Strip JIS G 4304 SUS321 (1) --G 4304 SUS347 (1) --G 4304 SUS405 (1) G 4304 SUS410 (1) G 4304 SUS410S (1) G 4304 SUS430 (1) BS 1501-321S12 1501-321S49 1501-3-07S17 1501-347S49 1501-405S17 ------- DIN 17440/1 X6CrNiTi1810 --17440/1 X6CrNiNb1810 --17440/1 X6CrAl13 17440/1 X10Cr13 17440/1 X6Cr13 17440/1 X6Cr17 G 3601 (2) --- 17440/1 G 3601 (2) 3740 (2) 17440/1 G 3602 (2) --- 17743 NiCu30Fe G 3101 SS330 G 3101 55330 G 3101 SS400 G 3101 SS400 4360 Gr 40A/B/C 4360 Gr 40A/B/C 4360 Gr 40D 4360 Gr 43A/B/C/D 17100 St33 17100 St33 17100 St44-2 17100 St44-2 A-264 Stainless Chromic-Nickel SteelClad Plate, Sheet, and Strip A-265 Nickel and Nickel-Base Alloy-Clad Steel Plate A-283 Low and Intermediate Tensile Strength Carbon Steel Plates, Shapes, and Bars Gr A Gr B Gr C Gr D Note (1): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307, respectively. Note (2): Specify mechanical properties, test and inspection in accordance with ASTM. STANDARD SPECIFICATION ASTM A-285 Pressure Vessel Plates, Carbon Steel, Low-and Intermediate-Tensile Strength Gr A & B Gr C JIS BS DIN --G 3103 S8410 1501-151 Gr 360 1501-151 Gr 430 17155 H I 17155 H II A-299 Pressure Vessel Plates, Carbon Steel, Manganese Silicon G 3115 SPV355 --- 17102 StE355 A-302 Pressure Vessel Plates, Alloy Steel Manganese-Molybderalm and Manganese-HolybdenumNickel Gr A Gr B Gr C Gr D G 3119 SBV1A G 3119 SBV1B G 3119 SBV2 G 3119 SBV3 --------- --------- A-387 Pressure Vessel Plates, Alloy Steel Chromium-Molybdenum Gr 2 Class 1 Gr 11 Class 1 Class 2 Gr 12 Class 1 Class 2 Gr 21 Class 1 Gr 22 Class 1 Class 2 Gr 5 Class 1 Class 2 Gr 9 Class 1 Class 2 G 4109 SCMV1 G 4109 SCMV3 G 4109 SCMV3 G 4109 SCMV2 G 4109 SCMV2 G 4109 SCMV5 G 4109 SCMV4 G 4109 SCMV4 G 4109 SCMV6 G 4109 SCMV6 ----- --1501-621 1501-621 1501-620 1501-620 --1501-622 Gr 515 1501-622 Gr 515 --------- ----- ASTM A-442 Pressure Vessel Plates, Carbon Steel, Improved Transition Properties Gr 55 JIS --- Gr 60 G 3115 SPV235 BS 1501-151 Gr 400 1501-161 Gr 400 1501-224 Gr 400 1501-151 Gr 430 1501-161 Gr 430 1501-224 Gr 430 A-516 Pressure Vessel Plates, Carbon Steel, for Moderate and Lower Temperature Service Gr 55 DIN SEW 680 TTSt41N --- - --- Gr 60 G 3118 SGV410 Gr 65 Gr 70 G 3118 SGV450 G 3118 SGV480 Note (1): 17155 13CrMo44 ----17155 10CrMo910 --SEW590 12CrMo195 ------- 1501-161 Gr 400 1501-224 Gr 400 1501-161 Gr 430 1501-224 Gr 430 1501-224 Gr 460 1501-224 Gr 490 17155 H I 17155 H II 17155 17Mn4 17155 19Mn6 Recognize lacer minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM. Molybdenum and Manganese.Alloy Steel Quenched and Tempered Manganese. Sheet. Carbon.1 St12 --- . Sheet and Strip. Carbon-ManganeseSilicon Steel Class 1 G 3115 SPV355N Class 2 G 3115 SPV450Q 1501-224 Gr 490 (1) --- DIN ------------- 17155 19Mn6 17102 StE355 --- A-570 Steel. Carbon.STANDARD SPECIFICATION Note (1): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration. HeatTreated. or specify minimum tensile and yield strengths per ASTM.Molybdenum Nickel JIS BS Type A Class 1 Class 2 Type B Class 1 Class 2 Type C Class 1 Class 2 G 3120 SQV1A G 3120 SQV1B G 3120 SQV2A G 3120 SQV2B G 3120 SQV3A G 3120 SQV3B ------------- A-537 Pressure Vessel Plates. Structural Quality. Hot-Rolled. ASTM A-533 I Pressure Vessel Plates. test and inspection in accordance with ASTM. Cold-Rolled Structural Quality Gr B Gr C Gr D G 3141 SPCC (2) G 3141 SPCC (2) G 3141 SPCC (2) ------- --1623. Note (2): Specify mechanical properties. Gr 30 Gr 33 Gr 36 Gr 40 Gr 45 Gr 50 G 3101 SS330 G 3101 SS400 G 3101 SS400 G 3101 SS400(1) G 3101 SS490 G 3101 SS490(1) 1449-HR 34/20 (1) 1449-HR 37/23 1449-KR 37/23 1449-HR 43/25 1449-HR 43/25 (1) 1449-HR 50/35 17100 St33 17100 St44-2 17100 St44-2 17100 St44-2 17100 St52-3 17100 St52-3 A-611 Steel. ASTM A-652 Pressure Vessel Plates. Note (2): Recognize lager minimum tensile or yield strengths of the underlined substitute materials in design consideration. Carbon Manganese. for Moderate and Lower Temperature Service Gr A Gr B Gr C JIS G 3126 SLA235 (1) G 3126 SLA325 (1)(2) G 3126 SLA360 (1) BS ------- DIN --17102 EStE315 17102 EStE355 .STANDARD SPECIFICATION Note (1): Specify Impact Test requirement per ASTM. or specify minimum tensile and yield strengths per ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration. ASTM A-53 Pipe.8 17175 St45. or specify minimum tensile and yield strengths per ASTM. Electric-Fusion (Arc)Welded (Size NPS 16 and over) Material A 283 Gr A – D G 3457 STPY400 A 285 Gr A – C A 570 Gr 30 – 40 A 36 G 3457 STPY400(1) G 3457 STPY400 (1)(2) G 3457 STPY400 3602 SAW410 3601 SAW410 ----3602 SAW410 3601 SAW410 ------ .0 1629 St44.0 3602 HFS360 3602 CFS360 3602 HFS410 3602 CFS410 3602 HFS460 3602 CFS460 17175 St35.STANDARD SPECIFICATION Table 2 PIPE Note (1): Specify carbon. Black and Hot-Dipped Zinc-Coated Welded and Seamless JIS Type F Gr A G 3452 SGP G 3454 STPG370 Gr B G 3454 STPG410 BS DIN 1387 3601 ERW360 S360 3601 ERW410 S410 1615 St33 1626 St37.455 STPT410 Gr C G 3456 STPT480 17175 St45. or silicon contents to accordance with ASTM. manganese. Steel. Steel.0 1629 St37.8 A-106 Seamless Carbon Steel Pipe for High-Temperature Service Gr A G 3456 STPT370 Gr B G 3.0 1626 St44.8 A-134 Pipe. S26 TP 316H (16Cr-12Ni-2Mo) TP 316L (16Cr-12Ni-2Mo) G 3459 SUS316HTP G 3459 SUS316LTP 3605-316S59 3605-316S14. manganese.S17 TP 347H (18Cr-10Ni-Cb) G 3459 SUS347H TP 3605-347S59 17457/58 X5CrNi1810 --17457/58 X2CrNi1911 ----17457/58 X5CrNiMo17122 17459E X6CrNiMo1713 17457/58 X2CrNiMo17132 17457/58 X6CrNiTi1810 SEW470 X12CrNiTi189 17457/58 X6CrNiNb1810 --- A-139 Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and over) Gr A – E A-211 Spiral-Welded Steel or Iron Pipe A-312 Seamless and Welded Austenitic Stainless Steel Pipe . G 3457 STPY400 (2)(3) 3602 SAW410 (2) 3601 SAW410 (2) --- A 570 Gr 30-45 G 357 STPY400 (2)(3) --- A 570 Gr 50 --- 3602 SAW 410 (2) 3601 SAW 410 (2) 3502 SAW 460 (2) TP 304 (18Cr-8Ni) TP 304H (18Cr-8Ni) TP 304L (18Cr-8Ni) TP 309 (23Cr-12Ni) TP 310 (25Cr-20Ni) TP 316 (16Cr-12Ni-21Mo) G 3459 SUS304TP G 3459 SUS304HTP G 3459 SUS304LTP G 3459 SUS309STP G 3459 SUS310STP G 3459 SUS316TP 3605-304S18. Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration.S22 ----3605-316S18. Specify carbon.S22 TP 321 (18Cr-10Ni-Ti) TP 321H (l8Cr-12Ni-Ti) TP 347 (18Cr-10Ni-Cb) G 3459 SUS321TP G 3459 SUS321HTP G 3459 SUS347TP 3605-321S18.S22 3605-321S59 3605-347S18.STANDARD SPECIFICATION Note (1): Specify electric resistance-welding. or silicon contents in accordance with ASTM. Note (3): ASTM A-135 Electric-Resistance-Welded Steel Pipe Gr A Gr B JIS BS DIN G 3454 STPG370 (1) G 3454 STPG410 (1) 3601 ERW360 3601 ERW410 1626 St37.0 1626 St44.S25 3605-304S59 3605-304S14.0 . or specify minimum tensile and yield strengths per ASTM. STANDARD SPECIFICATION Note (1):Recognize Lower minimum tensile or yield strengths of the underlined substitute materials in design consideration or specify minimum tensile and yield strengths per ASTM. Note (2):VdTuv-Werkstoftblatt ASTM A-333 Seamless and Welded Steel Pipe for Low-Temperature Service JIS Gr 1 G 3460 STPL380 Gr 3 (3-1/2Ni) G 3460 STPL450 Gr 6 --- Gr 8 (9Ni) G 3460 STPL690 BS DIN 3603-CFS410 LT50 3603-HFS410 LT50 3603-ERW410 LT50 3603-CEW410 LT50 3603-HFS503 LT100 3603-CFS503 LT100 3603-CFS410 LT50 3603-HFS410 LT50 3603-ERW410 LT50 3603-CEW410 LT50 3603-HFS509 LT196 3603-CFS509 LT196 17173 TTSt35N 17174 TTSt35N 17175 15Mo5 Wbl 007/2 12CrMo195 (2) 17173 l0Ni14 SEW680 TTSt45N 17173 X8Ni9 A-335 Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service Gr P1 (C-1/2Mo) Gr P5 (5Cr-1/2Mo) G 3458 STPA12 G 3458 STPA25 --3604 CFS625 (1) Gr P9 (9Cr-1Mo) G 3458 STPA26 3604 HFS625 (1) 3604-CFS629-470 (1) Gr P11 (1-1/4Cr-1/2Mo) G 3458 STPA23 Gr P12 (1Cr-1/2Mo) G 3458 STPA22 Gr P22 (2-1/4Cr-1Mo) G 3458 STPA24 3604 CF5621 3604 HFS621 3604 CFS620-460 (1) 3604 HFS620-460 (1) 3604 CFS622 3604 HFS622 Wbl 109 X12CrMo91 (2) 17175 13CrMo44 17175 13CrMo44 17175 l0CrMo910 . STANDARD SPECIFICATION Note (1): Specify seamless. Type 316L A240. Type 304L A240. Type 321 A240. Type 316 A240. Type 304 A240. Type 347 JIS BS DIN G 3468 SUS304TPY G 3468 SUS304LTPY G 3468 SUS316TPY G 3468 SUS316LTPY G 3468 SUS321TPY G 3468 SUS347TPY 3605 LWHT 304S18 3605 LWHT 304S14 3505 LWHT 316S18 3605 LWHT 316S14 3605 LWHT 321S18 3605 LWHT 347S18 17457 17457 17457 17457 17457 17457 X5CrNi1810 X2CrNi1911 X5CrNiMo17122 X2CrNiMo17132 X6CrNiTi1810 X6CrNiNb1810 A-376 Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service TP 304 (18Cr-8Ni) G 3459 SUS304TP (1) 3605-304S18 TP 304H (18Cr-8Ni) TP 316 (16Cr-12Ni-2Mo) TP 316H (16Cr-12Ni-2Mo) G 3459 SUS304HTP (1) G 3459 SUS316TP (1) G 3459 SUS316HTP (1) 3605-304S59 3605-316S18 3605-316S59 TP 321 (18Cr-10Ni-Ti) TP 321H (18Cr-10Ni-Ti) TP 347 (18Cr-10Ni-Cb) TP 347H (18Cr-10Ni-Cb) G 3459 SUS321TP (1) G 3459 SUS321HTP (1) G 3459 SUS347TP (1) G 3459 SUS347HTP (1) 3605-321S18 3605-321S59 3605-347S18 3605-347S59 17459 X6CrNi1811 E --17458 X5CrNiMo17122 17459 X6CrNiMo1713 E 17458 X6CrNiTi810 --17458 X6CrNiNb1810 --- G 3468 SUS304TPY G 3463 SUS304LTPY G 3468 SUS316TPY G 3468 SUS316LTPY G 3468 SUS321TPY G 3468 SUS347TPY ------------- 17457 17457 17457 17457 17457 17457 A-409 Welded Large Diameter Austenitic Steel Pipe for Corrosive or High Temperature Service TP 304 (18Cr-8Ni) TP 304L TP 316 (16Cr-12Ni-2Mo) TP 316L TP 321 (18Cr-10Ni-Ti) TP 347 (18Cr-10Ni-Cb) X5CrNi810 X2CrNi1911 X5CrNiMo17122 X2CrNiMo17132 X6CrNiTi1810 X6CrN iNb1810 . ASTM A-358 Electric-Fusion-welded Austenitic Chromium-Nickel Alloy Steel Pipe For High-Temperature Service Grade 304 304L 316 316L 321 347 Material A240. ASTM A-524 Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures Gr 1 Gr 11 JIS/JPI BS DIN --- --- SEW680 TTSt41 --- G 3454 STPG370 (1)(2) --- 1626 St37.15%.STANDARD SPECIFICATION Note (i): Specify electric resistance-welding.0 JPI-SB42 JPI-SB46 JPI-SB49 JPI-SLA24B (3) JPI-SLA33B (3) ----JPI-SPV24 --JPI-SL3N28 --------------------- --------------------- A-587 Electric-Welded Low-Carbon Steel Pipe for the Chemical Industry A-671 Electric-Fusion-Welded Steel pipe for Atmospheric and Lower Temperatures Grade CA55 CB60 CB70 CB70 CC60 CC65 CD70 CE55 CE60 CF70 CF71 CK75 Material A285 Gr C A515 Gr 60 A515 Gr 65 A515 Gr 70 A516 Gr 60 A516 Gr 65 A537 CL 1 A442 Gr 55 A442 Gr 60 A203 Gr B A203 Gr E A299 . Note (2): Maximum carbon content shall be 0. Note (3): Specify Impact Test requirement per ASTM. Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration.Pressure Service at Moderate Temperature Grade A55 B55 B60 B65 B70 C55 C60 C65 C70 D70 E55 E60 L65 L70 L75 N75 Material A285 Gr C A515 Gr 55 A515 Gr 60 A515 Gr 65 A515 Gr 70 A516 Gr 55 A516 Gr 60 A516 Gr 65 A516 Gr 70 A537 CL 1 A442 Gr 55 A442 Gr 60 A204 Gr A A204 Gr B A204 Gr C A299 JIS/JPI JPI-SB42 --JPI-SB42 JPI-SB46 JPI-SB49 --JPI-SLA24B (1) JPI-SLA33B (1) ------JPI-SPV24 JPI-SB46M JPI-SB49M (2) ----- BS DIN --------------------------- --------------------------- ----- ----- .STANDARD SPECIFICATION Note (1): Specify Impact Test requirement per ASTM. or specify minimum tensile and yield strengths per ASTM. ASTM A-672 Electric-Fusion-Welded Steel Pipe for High. 4 1630 St44.4 Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration.7 17172 StE415.Pressure Service at High Temperatures Grade Material CM-65 A204 Gr A CM-70 A204 Gr B CM-75 A204 Gr C CMSH-70 A537 CL 1 CMS-75 A299 ½ Cr A337 Gr 2 CL 1 1 Cr A387 Gr 12 CL 1 1-1/4 Cr A387 Gr 11 CL1 2-1/4 Cr A387 Gr 22 CL1 5 Cr A387 Gr 5 CL 1 API 5L Line Pipe Gr A25 Gr A JIS/JPI DIN JPI-SB46M JPI-SB49M --------JPI-SCMV2 JPI-SCMV3 JPI-SCMV4 JPI-SCMV6 --------------------- --------_------------ 63452 SGP 63454 STPG370 1387 3601 ERW 360 3601 S 360 3601 ERW 430 (1) 3601 S 430 (1) 3601 SAW 430 (1) 6327 Part 1-8 (1) --------------------- --17172 StE210. or . Electric-Fusion-Welded for High.7 17172 StE360.4 1630 St52.7TM 1630 St37.7 Gr B 63454 STPG410 Gr X42 Gr X46 Gr X52 Gr X56 Gr X60 Gr X65 Gr X70 ------- --------------63455 STS370 63455 STS410 63455 STS480 Note (1): BS 17172 StE240.7 17172 StE290.7TM 17172 StE480.7 17172 StE385.7 17172 StE445.7 17172 StE320.STANDARD SPECIFICATION ASTM/API A-691 Carbon and Alloy Steel Pipe. Table 3 TUBES ASTM A-161 Seamless Low-Carbon and Carbon Molybdenum Steel Still Tubes for Refinery Service Low Carbon Steel Gr T1 JIS BS DIN G 3461 ST340 (1) (2) 3059 HFS320 (2) 3059 CFS320 (2) 17175 St35. Note (6): Maximum hardness shall be Rockwell B72. Carbon Steel HB 137 HB 125 17175 St35.8 --- A-179 Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes G 3461 STB340 (1)(5)(6) 3606 CFS 320 3059 S1 360 (5)(6) Note (1): Specify seamless.8 . Note (4): Specify electric resistance-welding. Note (2): Maximum hardness shall be as follows: Item Hot rolled tubes Cold drawn tubes Note (3): Specify killed steel.8 G 3462 STBA12 (1)(2)(3) G 3467 STFA12 (2) --- 17175 15Mo5 3059 ERW320 (3) 3059 CEW320 (3) 3059 ERW360 3059 CEW360 (3) 3059 ERW440 (3) 3059 CEW440 (3) 17177 St37. Note (5): Specify cold drawn.8 A-178 Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler Tubes Gr A G 3461 STB340 (40 Gr C G 3461 STB410 (4) Gr D --- 17177 St42. 8 Gr T5 Gr T9 G 3462 STBA25 (3)(4) G 3462 STBA26 (3)(5) Wbl 007/2 12CrMio195 (6) Wbl 109 X12CrMo91 (6) Gr T11 Gr T22 G 3462 STBA23 (3)(4) G 3462 STBA24 (3)(4) 3606 CFS 625 3059 S1 629-470 (3)(5) 3059 S2 629-470 (3)(5) 3606 CFS621 3606 CFS622 3059 S1 622-440 (3)(4) 3059 S2 622-440 (3)(4) A-199 Seamless Cold-Drawn Intermediate Alloy-Steel Heat-Exchenger and Condenser Tubes 17175 13CrMo44 17175 10CrMo910 A-200 Seamless Intermediate Alloy-Steel Still Tubs for Refinery Service Gr T5 Gr T7 Gr T9 Gr T11 Gr T22 G 3462 STBA25 (4) G 3467 STFA25 (4) --G 3462 STBA26 (5) G 3467 STFA26 (5) G 3462 STBA23 (4) G 3467 STFA23 (4) G 3462 STBA24 (4) G 3467 STFA24 (4) Note (1): Specify seamless. Note (4): Maximum hardness shall be Rockwell 885. Note (5): Maximum hardness shall be Rockwell B89. Note (6): VdTuv-Herkstoftblatt 3604 CFS625 (4) 3604 HFS625 (4) --3604 CFS629-470 (5) 3604 HFS629-470 (5) 3059 S1 629-470 (5) 3059 S2 629-470 (5) 3604 CFS621 (4) 3604 HES621 (4) 3059 S1 622-440 (4) 3604 CFS622 (4) 3604 HFS622 (4) Wbl 007/2 12CrMo195 (6) --Wbl 109 X12CrMo91 (6) 17175 13CrMo44 17175 10CrMo910 . Note (3): Specify cold drawn.Pressure Service JIS BS DIN G 3-061 STB340 (1)(2) 3059 HFS 320 (2) 3059 CFS 320 (2) 3059 S1 360 (2) 3059 S2 360 (2) 17175 St35. Note (2): Maximum hardness shall be Rockwell 677.STANDARD SPECIFICATION ASTM A-192 Seamless Carbon Steel Boiler Tubes for High. Super heater and Heat-Exchanger Tubes Note (1): Specify seamless. Note (3): Maximum hardness shall be Rockwell B81. Note (4): Maximum hardness shall be Rockwell B79. Note (7): VdTuv-Werkstoftblatt 17175 10CrMo910 17458 X5CrNi1810 --17458 X2CrNi1911 --17458 X5CrNiMo17122 17459E X6CrNiMo1713 17458 X2CrNiMo17132 17458 X6CrNiTi1810 --17458 X6CrNiNb1810 --- .STANDARD SPECIFICATION ASTM A-209 Seamless Carbon-Molybdenum Alloy-Steel Boiler and Super Heater Tubes JIS Gr T1 G 3462 STBA12 (1)(2) Gr Tla G 3462 STBA13 (1)(3) Gr Tlb --- A-210 Seamless Medium-Carbon Steel Boiler and Super heater Tubes Gr A1 BS DIN 3059 S1 243 (2) 3059 S2 243 (2) 3059 S1 243 (3) 3059 S2 243 (3) --- 17175 15Mo5 --17175 15Mo5 ~ --- G 3461 STB410 (1)(4) 3059 S1 440 S2 440 (4) 17175 St45. Note (6): Maximum hardness shall be Rockwell B90.8 Gr T 5 G 3462 STBA25 (5) 3606 CFS 625 Gr T 11 Gr T 12 G 3462 STBA23 (5) G 3462 STBA22 (1)(5) Gr T 22 G 3462 STBA24 (5) Gr TP 304 Gr TP 3D4H Gr TP 304L Gr TP 310 Gr TP 316 Gr TP 316H Gr TP 316L Gr TP 321 Gr TP 321H Gr TP 347 Gr TP 347H G 3463 SUS304 TB (1)(6) G 3463 SUS304H T8 (1)(6) G 3463 SUS304L TB (1)(6) G 3463 SUS310S TB (1)(6) G 3463 SUS316 TB (1)(6) G 3463 SUS316H TB(1)(6) G 3463 SUS316L TB (1)(6) G 3463 SUS321 TB (1)(6) G 3463 SUS321H TB(1)(6) G 3463 SUS347 TB (1)(6) G 3463 SUS347H TB(1)(6) 3606 CFS 621 3506 CFS 620 3059 S1/S2 620 (5) 3606 CFS 622 3059 S1/S2622440/490(5) 3606 CFS 304S25 3059 CFS304S59 (6) 3606 CFS304S22 --3606 CFS316S25 3059 CFS316S59 (6) 3606 CFS316S29 3606 CF5321S22 3059 CFS321S59 (6) 3606 CFS347S17 3059 CFS347S59 (6) Wbl 007/2 12CrMo195 (7) 17175 13CrMo44 17175 13CrMo44 A-213 Seamless Ferritic and Austenitic Alloy-Steel Boiler. Note (2): Maximum hardness shall be Rockwell B90. Note (5): Maximum hardness shall be Rockwell B85. Tubes TP 304 TP 304H TP 304L TP 309 TP 310 TP 316 TP 316H TP 316L TP 321 TP 321H TP 347 TP 347H Note (1): Specify electric resistance-welding.8 G 3463 SUS304 TB (3) G 3463 SUS304H TB (3) G 3463 SUS304L TB (3) G 3463 SUS309S TB (3) G 3463 SUS310S TB (3) G 3463 SUS316 TB (3) G 3463 SUS316H TB (3) G 3463 SUS316L TB (3) G 3463 SUS321 TB (3) G 3463 SUS321H TB (3) G 3463 SUS347 TB (3) G 3463 SUS347H TB (3) --3059-ERW304S59 (3) --------3059-ERW316S59 (3) ----3059 ERW321S59 (3) --3059-ERW347S59 (3) 17457 X5CrNi1810 --17457 X2CrNi1911 ----17457 X5CrNiMo17122 A-226 Electric-Resistance-Welded Carbon Steal Boiler and Superheater Tubes for High-Pressure Service A-249 Welded Austenitic Steel Boiler.8 G 3461 STB340 (1)(2) 3059 ERW320 (2) 3059 CEW320 (2) 3059 ERW360 (2) 3059 CEW360 (2) 17177 St37. Note (3): Maximum hardness shall be Rockwell B90. Note (2): Maximum hardness shall be Rockwell B72. and Condense. Superheater. 17457 X2CrNiMo17132 17457 X6CrNiTi1810 --17457 X6CrNiNb1810 --- . Heat-Exchanger.STANDARD SPECIFICATION ASTM A-214 Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes JIS BS DIN G 3461 STB340 (1)(2) 3606 ERW 320 3059 ERW 320 (2) 3059 CEW 320 (2) 3059 ERW 360 (2) 3059 CEW 360 (2) 17177 St37. S22 (2) 3605-347S18. Note (2): Maximum hardness shall be Rockwell B90.S17 (2) ------------- G 3463 SUS304 TB (2)(3) G 3467 SUS304 TF (2) G 3463 SUS304H TB (2)(3) G 3467 SUS304H TF (2) G 3463 SUS316 TB (2)(3) G 3467 SUS316 TF (2) G 3463 SUS316 HTB (2)(3) G 3467 SUS316 HTF (2) G 3463 SUS321 TB (2)(3) G 3467 SUS321 TF (2) G 3463 SUS32114 TB (2)(3) 3605-304S18 (2) 17459E X6CrNi1811 3605-304S59 (2) 3059-CFS304S59 (2) 3605-316S18 (4) --- 3605-316S59 (4) 3059-316S59 (4) 3605-321S18 (2) 17459E X6rNiMo1713 3605-321S59 Gr 1010 (2) 3059-CFS321S59 Gr 1010(2) 3605-347S18 (2) --- 3605-347S59 (2) 3059-CFS347S59 (2) ----- A-271 Seamless Austenitic Chromium Nickel Steal Still Tubes for Refinery Service TP 304 TP 304H TP 316 TP 316H TP 321 TP 321H JIS G 3467 SUS321H TF (2) TP 347 TP 347H G 3463 SUS347 TB (2)(3) G 3467 SUS347 TF (2) G 3463 SUS347H TB (2)(3) G 3467 SUS347H TF (2) Note (1): Maximum hardness shall be Rockwell B95. Note (4): Maximum carbon content shall be 0.S22 (2) 3605-321S18. Note (3): Specify seamless.21% BS DIN 17458 X5CrNiMo17122 17458 X6CrNiTi1810 17458 X6CrNiNb1810 .STANDARD SPECIFICATION ASTM A-268 Seamless and Welded Ferritic Stainless Steel Tubing for General Service TP 410 TP 430 G 3463 SUS410 TB (1) G 3463 SUS430 TB (2) ----- ----- A-269 Seamless and Welded Austenitic Stainless Steel Tubing for General Service TP 304 TP 304L TP 316 TP 316L TP 321 TP 347 G 3463 SUS304 TB (2) G 3463 SUS304L TB (2) G 3463 SUS316 TB (2) G 3463 SUS316L TB (2) G 3463 SUS321 TB (2) G 3463 SUS347 TB (2) 3605-304S18.S25 (2) 3605-304S14.S26 (2) 3605-316S14.S22 (2) 3605-316S18. STANDARD SPECIFICATION ASTM A334 Seamless and Welded Carbon And Alloy-Steel Tubes for Low-Temperature Service Gr 1 JIS G 3464 STBL380 (1) Gr 3 G 3464 STBL450 (2) Gr 6 --- Gr 8 G 3464 STBL690 (2) Note (1): Maximum hardness shall be Rockwell B85. Note (2): Maximum hardness shall be Rockwell B90. BS 3603 CEW410 LT50 (1) 3603 CFS410 LT50 (1) 3603 ERW410 LT50 (1) 3603 HFS410 LT50 (1) 3603 CFS503 LT100 (2) 3603 HFS503 LT100 (2) 3603 CEW410 LT50 (2) 3603 CFS410 LT50 (2) 3603 ERW410 LT50 (2) 3603 HFS4110 LT50 (2) 3603 CFS509 LT196 (2) 3603 HFS509 LT196 (2) DIN 17173 T7St35N 17174 TTSt35N 17173 10Ni14 SEW680 TTSt45N 17173 X8Ni9 . Purpose Piping Class 60 Class 70 G 3202 SFVC1 G 3202 SFVC2A 1503-221-430 1503-221-490 17200 C22N --- A-182 Forged or Rolled Alloy-Steel Pipe Flanges. or . Forged Fittings. for General .Nr17386 X12CrMo910 SEW550 16CrMo44 SEW550 13CrMo44 --SEW550 10CrMo9I0 17440 X5CrNi1810 --17440 X2CrNi1911 17440 X5CrNiMo17122 --17440 X2CrNiMo17132 17440 X6CrNiTi1810 --17440 X6CrNiNb1810 --- Note (1): DIN Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration. For Piping Components JIS BS G 3202 SFVC2A 1503-221-490 --- A-181 Forging. Carbon Steel.St. Carbon Steel. and Valves and Parts for High –Temperature Service F1 (C-1/2Mo) FS (5Cr-1/2Mo) F9 (9Cr-1Mo) G 3203 SFVAF1 G 3203 SFAF58 G 3203 SFVAF9 1503-245-420 (1) 1503-625-520 --- F11 (1-1/4Cr-I/2Mo) F12 (1Cr-1/2Mo) F21 (3Cr-1Mo) F22 (2-1/4Cr-1Mo) F304 (18Cr-8Ni) F304H (18Cr-8Ni) F304L (18Cr-8Ni) F316 (16Cr-12Ni-2Mo) F316H (16Cr-12Ni-2Mo) F316L (16Cr-12Ni-2Mo) F321 (18Cr-10Ni-Ti) F321H (18Cr-10Ni-Ti) F347 (18Cr-10Ni-Cb) F347H (18Cr-10Ni-Cb) G 3203 SFVAF11A G 3203 SFVAF12 G 3203 SFVAF21B G 3203 SFVAF22B G 3214 SUS304 G 3214 SUS304H G 3214 SUSF304L G 3214 SUSF316 G 3214 SUSF316H G 3214 SUS316L G 3214 SUS321 G 3214 SUSF321H G 3214 SUSF347 G 3214 SUSF347H 1503-621-460 1503-620-540 --1503-622-560 1503-304S31 1503-304S51 1503-304S11 1503-316S31 or 33 1503-316S51 1503-316S11 or 13 1503-321S31 1503-321S51-510 1503-347S31 1503-347S51 VdTuv201 16Mo5 VdTuv1207 12CrMo195 W.STANDARD SPECIFICATION Table 4 FORGINGS ASTM A-105 Forging. Temperature Parts Refer to A-182 Refer to A-182 Refer to A-182 LF1 LF2 G 3205 SFL1 G 3205 SFL2 SEW680 TTSt41 SEW680 TTStE36 LF3 (3-1/2Ni) G 3205 SFL3 1503-221-430 (1) 1640 WPLO 1503-221-490 (1) 1640 WPL3 1503-503-490 (1) A-350 Forging. Carbon and Low-Alloy Steel.STANDARD SPECIFICATION ASTM A-226 Forging. for Pressure Vessel Component JIS BS DIN Class 1 Class 2 Class 4 G 3202 SFVC1 G 3202 SFVC2A G 3202 SFVC2B 1503-221-430 1503-221-490 17200 C22N --- A-336 Steel Forging. Alloy. for Pressure and High. Carbon and Alloy Quenched and Tempered. . Carbon Steel. Note (2): Specify heat treatment and mechanical properties per ASTM. for Pressure Vessel Component Class 1 Class 2 Class 3 Note (1): Specify Impact Test requirement per ASTM. Requiring Notch Toughness Testing for Piping Component 17280 10Ni14 A-508 Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forging for Pressure Vessel Class 1 Class 2 Class 3 G 3202 SFVC2B G 3204 SFVQ2A G 3204 SFVQ1A ------- --SEW640 22NiMoCr37 SEW640 20MrMoNi55 G 3202 SFVC2B G 3204 SFVQ2A G 3204 SFVQ1A 1503-221-490 (1)(2) ----- ------- A-541 Steel Forging. or silicon contents in accordance with ASTM. Carbon. .STANDARD SPECIFICATION Table 5 CASTINGS ASTM A-27 Steel Castings. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration. or specify minimum tensile and yield strengths per ASTM. manganese. for General Application Gr 60-30 Gr 65-35 Gr 70-36 JIS BS DIN G 5101 SC410 (1) G 5101 SC450 (1) G 5101 SC480 (1) 3100 Steel A1 --3100 Steel A2 1681 GS-38 (2) 1681 GS-45 1681 GS-52 Gr 32510 Gr 35018 G 5702 FCM3340 G 5702 FCM3360 6681 B35-12 --- 1692 GTS-35-10 1692 GTS-35-10 (2) A-48 Gray Iron Castings Class 20 Class 25 Class 30 Class 35 Class 40 Class 45 Class 50 Class 55 Class 60 G 5501 FC150 G 5501 FC200 G 5501 FC200 (2) G 5501 F 250 G 5501 FC300 G 5501 FC300 (2) G 5501 FC350 ----- 1452 Gr 150 1452 Gr 180 1452 Gr 220 1452 Gr 260 1452 Gr 300 1452 Gr 300 (2) 1452 Gr 350 1452 Gr 400 --- 1691 GG-15 1691 GG-20 1691 GG-20 (2) 1691 GG-25 1691 GG-30 1691 GG-30 (2) 1691 GG-35 --- G 5501 FC200 G 5501 FC250 G 5501 FC300 1452 Gr 180 1452 Gr 260 1452 Gr 300 1691 GG-15 1691 GG-25 1691 GG-30 A-47 Ferrltic Malleable Iron Castings A-126 Gray Iron Castings for Valves Flanges and Pipe Fittings Class A Class 6 Class C Note (1): Specify carbon. Suitable for High-Temperature Service WC1 (C-1/2Mo) WC6 (1-1/4Cr-1/2Mo) WC9 (2-1/4Cr-1Mo) C5 (Cr-1/2Ho) C12 (9Cr-1Mo) G 5151 SCPH11 (1) G 5151 SCPH21 (1) G 5151 SCPH32 (1) G 5151 SCPH61 (1) --- 1504-245 1504-621 1504-622 1504-625 1504-629 17245 GS-22Mo4 17245 GG-17CrMo55 17245 CS-19CrMo910 SEW 595 GS-2CrMo195 SEW 595 GS-2CrMo101 G 5122 SCH2 G 5122 SCH11 G 5122 SCH17 G 5122 SCH12 G 5122 SCH13 G 5122 SCH18 G 5122 SCH22 or 21 G 5122 SCH19 G 5122 SCH15 G 5122 SCH20 ----3100-309C40 3100-302C35 3100-309C30 --3100-310C40 3100-311C11 3100-330C12 3100-331C60 --------------------- A-297 Steel Castings. Heat Resistant.STANDARD SPECIFICATION ASTM A-216 Steel Castings. . Iron-Chromium and Iron-Chromium-Nickel. Note (3): Specify elongation in accordance with ASTM. for Pressure-Containing Parts. Martensitic Stainless and Alloy. or silicon contents in accordance with ASTM. Note (2): Specify carbon. manganese. except for the chemical analysis and mechanical properties of the steel. For High-Temperature Service WCA WCB WCC JIS BS DIN G 5151 SCPH1 (1) G 5151 SCPH2 (1) --- 1504-161 Gr 430 1504-161 Gr 480 1504-161 Gr 540 (2)(3) 17245 GS-C25 17245 GS-C25 --- A-217 Steel Castings. for General Application Gr HC Gr HD Gr HE Gr HF Gr HH Gr HI Gr HK Gr HN Gr HT Gr HU Note (1):Test and inspect the product in accordance with ASTH. Suitable for Fusion Welding. Carbon. except for the chemical analysis and mechanical properties of the steel. and Valve Parts for Railroad. . test and inspection in accordance with ASTM. for High-Temperature Service Gr CF3 (18Cr-8Ni) G 5121 SCS19A (1) Gr CF3A (18Cr-8Ni) Gr CF3M (17Cr-10Ni-2Mo) --G 5121 SCS16A (1) Gr CF8 (18Cr-8Ni) G 5121 SCS13A (1) Gr CF8A (18Cr-8Ni) Gr CF8C (20Cr-10Ni-Cb) --G 5121 SCS21 (1) Gr CF8M (18Cr-10Ni-2Mo) G 5121 SCS14A (1) Gr CH10 (25Cr-13Ni) Gr CH20 (25Cr-13Ni) Gr CK20 (25Cr-20Ni) Gr CN7M (28Ni-20Cr2Mo-3Cb) Gr HK40 (25Cr-20Ni) G 5121 SCS17 (1)(2) G 5121 SCS17 (1)(3) G 5121 SCS18 (1) G 5121 SCS23 (1) G 5122 SCH22 (1) BS 1504-304C12 (2) 3100-304C12 (2) --1504-316C12 (2) 3100-316C12 (2) 1504-304C15 3100-304C15 --1504-347C17 3100-347C17 1504-316C16 3100-316C16 --3100-309C30 --1504-332C11 1504-310C40 3100-310C40 DIN ------17445 G-X6CrNi189 _-17445 G-X5CrNiNb189 17445 G-X6CrNiMo1810 ----------- Note (1): Test and inspect the product in accordance with ASTM. Austenitic. or specify minimum tensile and yield strengths per ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration. and Other Heavy Duty Service at Temperatures up to 650°F (345°C) JIS A-351 Steel Castings. Pipe Fittings. Note (3): Specify mechanical properties.STANDARD SPECIFICATION ASTM A-338 Malleable Iron Flanges. Marine. Ferritic and Martensitic. APPENDIX-1 FCD-S 2789 Gr 420/12 (2) --- G 5122 SCH13 (3) 3100-309C32 --- ------- 3071-NAI 3071-NA2 (4) 3071-NA3 ------- --SEW685 GS-10Ni14 --- A-395 Ferritic Ductile Iron PressureRetaining Castings for Use at Elevated Temperatures A-447 Steel Castings.STANDARD SPECIFICATION ASTM A-352 Steel Castings. for PressureContaining Parts Suitable for Low-Temperature Service LCB LC1 (C-1/2Mo) JIS G 5152 SCPL1 (1) G 5152 SCPL11 (1) LC2 (2-1/2Ni) LC3 (3-1/2Ni) G 5152 SCPL21 (1) G 5152 SCPL31 (1) LC9 --- BS DIN 1504-161 Gr 480 LT40 1504-245 LT50 3100-BL1 --1504-503 LT60 3100-BL2 --- SEW685 GS-CK24 --- 88243. chemical requirement and mechanical properties. or specify minimum tensile and yield strengths per ASTM. Chromium-Nickel -Iron Alloy Castings (25-12 Class) for High-Temperature Service A-494 Casting. . Note (2): Specify ferritizing heat treatment. test and inspection in accordance with ASTM Note (4): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration. except for the chemical analysis and mechanical properties of the steel. Note (3): Specify mechanical properties. except for tensile and yield strengths. Nickel and Nickel Alloy M-35-1 M-30H M-25S Note (1): Test and inspect the product in accordance with ASTH. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration. Note (3): Test and inspect the product in accordance with ASTM. Iron-Chromium Nickel. . Corrosion Resistant. except for the chemical analysis and mechanical properties of the steel.STANDARD SPECIFICATION ASTM A-536 Ductile Iron Castings Gr 60-40-18 Gr 65-45-12 Gr 80-55-06 Gr 100-70-03 JIS BS DIN G 5502 FCD450 (1) G 5502 FCD500 (1) G 5502 FCD600 (1) G 5502 FCD700 (1) 2789 Gr 420/12 2789 Gr 500/7 2789 Gr 600/3 (2) 2789 Gr 700/2 (2) --1693 GGG-50 1693 GGG-60 1693 GGG-70 A-743 Castings. Iron-Chromium. or specify minimum tensile and yield strengths per ASTM. Nickel Base. for General Application Gr CA-15 Gr CA-40 G 5121 SCS1 (3) G 5121 SCS2 (3) 17445 G-X20Cr14 --- Gr CF-3 G 5121 SCS19A (3) Gr CF-3M G 5121 SCS16A (3) Gr CF-8 G 5121 SCS13A (3) Gr CF-8C Gr CF-8M G 5121 SCS21 (3) G 5121 SCS14A (3) Gr CF-20 Gr CH-20 Gr CK-20 Gr CN-7M G 5121 SCS12 (3) G 5121 SCS17 (3) G 5121 SCS18 (3) G 5121 SCS23 (3) 3100-410C21 (2) 1504-420C29 3100-420C29 1504-344C12 3100-304C12 1504-316C12 3100-316C12 1504-304C15 3100-304C15 1504-347C17 1504-316C16 3100-316C16 --3100-309C30 --1504-332C11 ----17445 G-X6CrNi189 17445 G-X5CrNiNb189 17445 G-X6CrNiMo1810 --------- Note (1): Specify elongation in accordance with ASTM. trt.trt. Note (2): Specify ASTH dimensional requirements.3 17200 CK25 1654 Cq22 Note (1): Specify heat treatment and mechanical properties per ASTM.) Gr B16 (Cr . tolerances and inspection.hd. Note (4):Test and inspect the product in accordance with ASTM.) CL 4 (304 str.) Gr B8M CL 1 (316 sol.hd.2Mo) G 4107 SNB7 (1) 1506-630-690 Gr B8 CL 1 (304 sol. Note (3): Specify mechanical properties.6 A-307 Carbon Steel Externally Threaded Standard Fasteners Gr B G 4051 S25C (4) 17100 St44.V) G 4303 SUS304 (2) 1506-304S31 --1654 X10Cr13 17200 42CrMo4 17240 24CrMo5 (3) 17200 42CrMo4 17240 24CrMo5 (3) 17440 X5CrNi1810 G 4303 SUS347 (2) 1506-347S31 17440 X6CrNiNb1810 G 4303 SUS316 (2) 1506-316S31 17440 X5CrNiMo17122 G 4303 SUS321 (2) 1506-321S31 17440 X6CrNiMTi1810 G 4107 SNB16 1506-670-860 17240 40CrMoV47 A-194 Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High-Temperature Service Gr 2H G 4051 S45C (3) 1506-162 Gr 4 (C-Mo) Gr 6 (12Cr) Gr 8 (304) Gr 8MA (316) -G 4303 SUS410 (3) G 4303 SUS304 (2) G 4303 Sus316 (2) --1506-410S21-770 1506-304S31 1506-316S31 17240 C35 1654 Cq45 17240 24CrMo5 1654 X10Cr13 17440 X5CrNi1810 17440 X5CrNiMo17122 G 3101 SS400 (4) 4190-Gr 4.Mo .STANDARD SPECIFICATION Table 6 BOLTS AND NUTS ASTM A-193 Alloy-Steel and Stainless Steel Bolting Materials for High Temperature Service Gr B5 (5Cr) Gr B6 (12Cr) Gr B7 (Cr-Mo) JIS BS DIN G 4107 SNB5 G 4303 SUS410 G 4107 SNB7 --1506-410S21-772 1506-630-860 Gr B7M (Cr-0.2 17100 St44.) CL 2 (321 str.) Gr B8C CL 1 (347 sol. test and inspection in accordance with ASTM. except for the chemical analysis and mechanical properties of the steel.trt.) CL 2 (347 str.) CL 2 (316 str.) Gr B8T CL 1 (321 sol.hd.hd.trt. . Note (2): Specify ASTM dimensional requirements. Studs.hd.) G 4303 SUS321 (2) Gr B8M (316 str.STANDARD SPECIFICATION ASTM A-320 Alloy Steel Bolting Materials for Low Temperature Service Gr L7 (Cr-Mo) JIS BS G 4107 SNB7 (1) 1506-630-860 Gr L43 (Ni-Cr-Mo) Gr B8 (304 str. with Expansion Coefficients Comparable to Austenitic Steels Gr 660 Class A & B (14Cr-24Ni) Gr 651 Class A & B (19Cr-9Ni) Note (1): Specify Impact Test requirement per ASTM.hd.hd. . 50 to 120 KSI (345 to 827 Mpa) Yield Strength.) G 4103 SNCM439 G 4303 SUS304 (2) G 4303 SUS347 (2) Gr B8T (321 str.) Gr B8C (347 str. High-Temperature .) G 4303 SUS316 (2) --1506-304S31 1506-347S31 970-347S31 1506-321S31 970-321S31 1506-316S31 970-316S31 DIN 17200 42CrMo4 17240 24CrMo5 --17440 X5CrNi1810 17440 X6CrNiNb1810 17440 X6CrNiTi1810 17440 X5CrNiMo17I22 A-325 High-Strength Bolts for Structure Steel Joints G 4051 S33C 3139 1654 Cq35 ----- ----- --- --- --- --- --- --- --- A-354 Quenched and Tempered Alloy Steel Bolts. tolerances and inspection.hd. and Other Externally Threaded Fasteners Gr BC Gr BD A-453 Bolting Materials. or . Carbon.STANDARD SPECIFICATION Table 7 BARS AND SHAPES ASTM A-276 Stainless and Heat-Resisting Steel Bars and Shapes Type 420 JIS BS DIN G4303 J1 970-420S37 17440 X20Cr13 Gr 1020 Gr 1025 Gr 1030 Gr 1035 Gr 1040 Gr 1045 G4051 S20C G4051 S25C G4051 S30C G4051 S35C G4051 S40C G4051 S45C ------------- 17200 CK22 17200 CK25 17200 CK30 17200 CK35 17200 CK40 17200 CK45 A-615 Deformed and Plain Billet-Steel Bars for Concrete Reinforcement Gr 40 Gr 60 G3112 SD295 G3112 SD390 (1) Gr 250 (1) Gr 460/425 (1) -488 BSt420S Gr 45 Gr 50 Gr 55 G3101 SS330 G3101SS330 (1) G3101 SS400 Gr 40A (1) Gr 40A (1) Gr 40A (1) Gr 60 G3101 SS400 (1) Gr 43A Gr 65 Gr 70 Gr 75 Gr 80 G3101 SS490 G3101 SS490 G3101 SS540 G3101 SS540 (1) Gr 50A (1) Gr 55C or 50A (1) Gr 55C or 50A (1) Gr 55C (1) 17100 St33 17100 St33 17100 St44-2 17100 St44-3 17100 St44-2 17100 St44-3 17100 St52-3 17100 St52-3 ----- A-576 Steel Bars. Carbon. Hot-Wrought. Mechanical Properties Note (1): Recognize loser minimum tensile or yield strengths of the underlined substitute materials in design consideration. Hot-Wrought Special Quality A-675 Steel Bars. Special Quality. STANDARD SPECIFICATION Table 8 PIPING FITTINGS ASTM A-234 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and Elevated Temperatures WPB WPC WP1 (C-1/2Mo) WP5 (5Cr-1/2Mo) WP9 (9Cr-1/2Mo) WP11 (1-1/4Cr-1/2Mo) WP12 (1Cr-1/2Mo) WP22 (2-1/4Cr-1Mo) A-403 Wrought Austenitic Stainless Steel Piping Fittings WP 304 (18Cr-8Ni) WP 304H(18Cr-8Ni) WP 304L (18Cr-8Ni) WP 316 (16Cr-12Ni-2Mo) WP 316H (16Cr-12Ni-2Mo) WP 316L (16Cr-12Ni-2Mo) WP 321 (18Cr-10Ni-Ti) WP 321H (18Cr-10Ni-Ti) WP 347 (18Cr-10Ni-Cb) WP 347H (18Cr-10Ni-Cb) JIS B 2312 PT410 6 2313 PT410W B 2312 PT480 B 2313 PT480W B 2312 PA12 B 2313 PA12W B 2312 PA25 B 2313 PA25W 8 2312 PA26 B 2313 PA-96W B 2312 PA23 B 2313 PA23W B 2312 PA22 B 2313 PA22W B 2312 PA24 8 2313 PA24W B2312 SUS304 B2313 SUS304W B2312 SUS304H B2312 SUS304L B2313 SUS304LW B2312 SUS316 B2313 SUS316W B2312 SUS316H B2312 SUS316L B2313 SUS316LW B2312 SUS321 B2313 SUS321W B2312 SUS321H B2312 SUS347 B2313 SUS347W B2312 SUS347H BS DIN 1640 WPB --- --- --- 1640 WP1 --- 1640 WP5 --- --- --- 1640 WP11 --- --- --- 1640 WP22 --- 1640-WP304 --- --1640-WP304L ----- 1640-WP316 --- --1640-WP316L ----- 1640-WP321 --- --1640-WP347 ----- --- --- . STANDARD SPECIFICATION JIS A-420 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low Temperature Service WL3 (3-1/2Ni) WL6 WL8 (9Ni) B 2312 PL450 B 2313 PL450W B 2312 PL380 B 2313 PL38OW B 2312 PL690 BS DIN 1640-WPL3 --- 1640-WPL0 --- --- --- . Standard Sizes H3300 C4430 --- 17671 CuZn15 H4552 NCUT 3074 --- H4630 TTP28 H4630 TTP35 H4630 TTP49 --- --------- 17850 Ti1 17850 Ti2 17850 Ti3 G4903 NCF 800TP G4903 HCF 800HTP G4903 NCF 825TP ------- ------- H3300 C7060 H3300 C7150 2871-CN102 2871-CN107 17664 CuNi10Fe1Mn 17664 CuNi30Mn1Fe B-165 Nickel-Copper Alloy Seamless Pipe and Tube N04400 B-167 Nickel-Chromium-Iron Alloys Seamless Pipe and Tubes N06600 G4903 NCF600TP B-337 Seamless and Welded Titanium and Titanium Alloy pipe Gr 1 Gr 2 Gr 3 Gr 7 B-407 Nickel-Iron-Chromium.STANDARD SPECIFICATION Table 9 NONFERROUS MATERIALS ASTM JIS BS DIN PIPE B-42 Seamless Copper Pipe. Alloy Seamless Pipe and Tube N08800 N08810 B-466 Seamless Copper-Nickel Pipe and Tube C70600 C71500 . Standards Sizes H3300 C1020 2871-C103 1787 OF-Cu B-43 Seamless Red Brass Pipe. STANDARD SPECIFICATION ASTM B-467 Welded Copper-Nickel Pipe JIS BS DIN C70600 C71500 H3320 C7060 H3320 C7150 2871-CN102 2871-CN107 17664 CuNi10Fe1Mn 17664 CuNi30Mn1Fe CASTINGS B-61 Steam or Valve Bronze Castings H5111 BC7 1400-LG4 --- H5111 BC6 1400-LG2 1705 G-CuSn5ZnPb B-62 Composition Bronze or Ounce Metal Castings . 4948 S 304 15 1.4303 (EN) X8CrNi18-12 S 306 00 1.4828 309 S 309 00 1.4829 X15CrNi23-13 309 S SUS 309 S S 309 08 1.4833 309 Cb S 309 40 www.4319 303 SUS 303 S 303 00 1.4372 X12CrMnNiN17-7-5 (EN) QMS 5 202 SUS 202 S 202 00 S 209 10 S 215 00 S 245 65 219 301 X4CrNiMn21-9-6 SUS 301 S 301 00 302 SUS 302 S 302 00 1.4833 309 H S 309 09 1.][® Austenitic stainless steel USA.4833 X6CrNi22-13 309 S SUS 309 S X12CrNi23-13 S 309 08 1.4310 (EN) X10CrNi18-8 1.4818 SUS 304 ELC 304 H SUS 304 H X8CrNi19-10 SUS 304 Cu1 SUS 304 Cu2 304 N SUS 304 N1 S 304 51 X5CrNiN18-10 SUS 304 N2 304 LN SUS 304 LN S 304 53 1. 1 .4891 S 304 15 1.4305 (EN) 1. Japan AISI grade JIS grade 201 SUS 201 Europe UNS designation S 201 00 EN / DIN numerical designation EN / DIN symbolical designation 1.com Steel grades equivalence tables Pág.4361 (EN) X1CrNiSi18-15-4 SUS 304 MF 305 SUS 305 SUS 305 J1 F 46 S 306 15 308 309 S 309 00 1.4828 X15CrNiSi20-12 309 S SUS 309 S S 309 08 1.4318 (EN) X2CrNiN18-7 X10CrNi18-9 X8CrNiS18-9 SUS 303 Cu SUS 303 HS2 SUS 303 HS3 303 Se SUS 303 Se S 303 23 304 SUS 304 S 304 00 X10CrNiS18-9 304 Cu SUS XM 7 S 304 30 304 L SUS 304 L S 304 03 1.4306 (EN) X2CrNi19-11 304 L SUS 304 L S 304 03 1.4307 (EN) X2CrNi18-9 S 304 09 1.4301 (EN) X6CrNi18-10 301 L 1.4311 (EN) X2CrNiN18-10 S 305 00 1.weisz. weisz.4919 X6CrNiMo17-12 S 316 51 (EN) X2CrNiMo17-12-2 X2CrNiMoN17-11-2 SUS 316 J1 SUS 316 J1L 316 N 1.4435 (EN) X2CrNiMo18-14-3 316 LN SUS 316 LN S 316 53 1.4406 (EN) X2CrNiMoN17-11-2 316 LS SUS 316 N 1.4841 X15CrNiSi25-20 310 1.4432 (EN) X2CrNiMo17-12-3 316 L SUS 316 L S 316 03 1.4465 X1CrNiMoN25-25-2 S 310 50 1.4571 316 Ti SUS 316 Ti S 316 35 1.4406 316 LN SUS 316 LN S 316 53 1.4404 316 L SUS 316 L S 316 03 1.4910 316 Ti SUS 316 Ti S 316 35 1.4406 316 L SUS 316 L S 316 03 1.4573 317 SUS 317 S 317 00 X2CrNiMoN17-11-2 (EN) X2CrNiMoN17-13-3 X2CrNiMoN18-14-3 316 S (EN) X6CrNiMoTi17-12-2 X10CrNiMoTi17-13-3 SUS 317 J1 www.4547 (EN) X1CrNiMoCuN20-18-7 X5CrNiMo17-12-2 314 SUS 314 S 314 00 1.4841 316 SUS 316 S 316 00 1. 2 .4427 X6CrNiMoS18-11 316 L SUS 316 L S 316 03 1.4466 (EN) X1CrNiMoN25-22-2 S 312 54 1.4435 (EN) X2CrNiMo18-14-3 316 L SUS 316 L S 316 03 1.4429 316 LN SUS 316 LN S 316 53 1.4401 (EN) 316 SUS 316 S 316 00 1.4335 (EN) X1CrNi25-21 1.4436 (EN) X3CrNiMo17-13-3 S 316 40 1.4845 310 Cb S 310 40 310 HCb S 310 41 310 HCbN S 310 42 X6CrNi25-20 (EN) X8CrNi25-21 310 SCB F44 S 310 50 1.4580 (EN) X6CrNiMoNb17-12-2 316 Cb X15CrNiSi25-20 316 F SUS 316 F S 316 20 1.4845 X12CrNi25-20 309 HCb S 309 41 SUS 310 ELC 310 L 310 L 1. Japan AISI grade Europe JIS grade UNS designation EN / DIN numerical designation EN / DIN symbolical designation 310 1.3952 316 LN SUS 316 LN S 316 53 1.4842 310 S SUS 310 S S 310 08 1.com Steel grades equivalence tables Pág.4466 (EN) X1CrNiMoN25-22-2 310 S SUS 310 S S 310 08 1.][® Austenitic stainless steel USA.4436 (EN) X3CrNiMo17-13-3 316 LS 1.4845 310 H S 310 09 1.4441 X6CrNiMo17-11 316 H SUS 316 H S 319 09 1. 3964 X2CrNiMnMoNNb21-16-5-3 S 209 10 1.4541 321 SUS 321 S 321 00 1.4550 347 H SUS 347 H S 347 09 1.4821 S 327 50 S 328 03 333 S 332 28 347 SUS 347 S 347 00 1.4434 (EN) X2CrNiMoN18-12-4 317 LM S 317 25 317 LN S 317 53 1.4878 X12CrNiTi18-9 321 H SUS 321 H S 321 09 1. Japan AISI grade JIS grade 317 L SUS 317 L Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation S 317 03 1.4941 X7CrNiTi18-11 S 326 15 S 326 54 327 1.com Steel grades equivalence tables Pág.][® Austenitic stainless steel USA.4439 (EN) X2CrNiMoN17-13-5 F 48 S 317 26 1.3974 X2CrNiMnMoNNb23-17-6-3 16-8-2H XM-10 S 219 00 XM-11 S 219 04 XM-15 S 381 00 SUS XM 15J1 XM-17 S 216 00 XM-18 S 216 03 XM-19 XM-19 SUS XM 19 XM-21 S 304 52 XM-29 S 240 00 XM-31 S 214 00 www.weisz.4438 (EN) X2CrNiMo18-15-4 317 L S 317 03 1.4439 (EN) X2CrNiMoN17-13-5 317 LMN S 317 26 1.3964 X2CrNiMnMoNNb21-16-5-3 S 209 10 1.4878 348 H S 348 09 (EN) X6CrNiNb18-10 X6CrNiNb18-12 347 HFG S 353 15 926 1.4961 348 S 348 00 1. 3 .4439 (EN) X2CrNiMoN17-13-5 (EN) X6CrNiTi18-10 318 319 319 L 321 SUS 321 S 321 00 1.4878 X12CrNiTi18-9 321 H SUS 321 H S 321 09 1.4835 1.4529 21-6-9 S219 04 22-13-5 S 209 10 (EN) X1NiCrMoCuN25-20-7 1. 4537 (EN) X1CrNiMoCuN25-25-5 1.4371 (EN) X2CrMnNiN17-7-5 1. Japan AISI grade Alloy 286 www.][® Austenitic stainless steel USA. 4 .4988 X8CrNiMoVNb16-13 Steel grades equivalence tables Pág.4981 X8CrNiMoNb16-16 1.com JIS grade Europe UNS designation S 662 86 EN / DIN numerical designation EN / DIN symbolical designation 1. Japan AISI grade JIS grade Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation 1.4373 (EN) X12CrMnNiN18-9-5 1.4848 X6CrNiCu18-10-4Kd High temperature austenitic stainless steel USA.4980 X5NiCrTi26-15 1.weisz.4961 X8CrNiNb16-3 1.4577 X5CrNiMoTi25-25 1. 4522 440 B S 440 00 439 L 441 442 443 SUS 443 S 443 00 444 QS 192 S 444 00 1.4749 X18CrN28 455 490 501 XM-15 QS 25T XM-27 QS 261 XM-33 S 446 27 S 446 26 18-2 QS 192 S 444 00 1.weisz.4016 (EN) X6Cr17 S 405 00 409 409 L SUS 410 LC 410 S 410 Ti SUS 410 Ti 418 429 SUS 429 S 429 00 430 SUS 430 S 430 00 430 F SUS 430 F S 430 20 430 Cb S 430 40 430 Ti SUS 430 Ti S 430 35 430 Ti SUS 430 Ti S 430 36 434 SUS 434 S 434 00 436 1.4113 X6CrMo17-1 1.4521 (EN) X2CrMoTi18-2 25-4-4 S 446 35 26-3-3 S 446 60 29-4 S 447 00 29-4C S 447 35 29-4-2 S 448 00 P9 S 504 00 S 890 40 S 890 25 www.4511 X3CrNb17 1.com Steel grades equivalence tables Pág.][® Ferritic stainless steel USA. 5 .4510 440 A S 440 00 1. Japan AISI grade JIS grade 405 SUS 405 Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation S 409 00 1.4509 (EN) X2CrTiNb18 (EN) X2CrMoTi18-2 S 430 35 1.4512 (EN) X2CrTi12 S 410 08 1.4521 (EN) X2CrMoTi18-2 19-3 QS 192 S 444 00 1.4521 446 SUH 446 S 446 00 1.4516 (EN) X6CrNiTi12 1.4536 439 (EN) X3CrTi17 1. 4505 1. 6 .][® Ferritic stainless steel USA.4590 (EN) X2CrNbZr17 1. Japan AISI grade Europe JIS grade UNS designation EN / DIN numerical designation EN / DIN symbolical designation S 890 26 1.weisz.4003 (EN) X2CrNi12 1.4513 (EN) X2CrMoTi17-1 1.4024 X15Cr13 1.4002 (EN) X6CrAl13 1.4506 1.4713 X10CrAl7 1.4520 (EN) X2CrTi17 1.4000 (EN) X6Cr13 1. Japan AISI grade www.4575 1.4781 X10CrAl24 Steel grades equivalence tables Pág.4605 (EN) X2CrAlTi18-2 1.4742 X10CrAl18 1.4592 (EN) X2CrMoTi29-4 1.4526 (EN) X6CrMoNb17-1 1.4724 Y 4L SIC 8 SIC 9 SIC 10 SIC 12 Heat resistant ferritic stainless steel USA.4017 (EN) X6CrNi17-1 1.com JIS grade Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation 1. 4501 (EN) X2CrNiMoCuWN25-7-4 2550 2550 QSA 2505 F 50 F 51 QS 2205 F 51 S 322 05 F 52 S 329 50 F 53 S 327 50 F 54 S 327 40 F 55 S 327 60 X3CrNiMoN27-5-2 S 312 54 QS 1905 S 315 00 1.com Steel grades equivalence tables Pág.4362 (EN) X2CrNiN23-4 S 392 74 www.4410 S 325 50 1.][® Duplex (ferritic / austenitic) stainless steel USA.4417 X2CrNiMoSi19-5 S 317 60 329 SUS 329 J1 S 329 00 SUS 329 J2L 4462 1.4460 S 325 50 1.weisz.4410 (EN) X2CrNiMoN25-7-4 1.4462 (EN) X2CrNiMon22-5-3 1.4462 (EN) X2CrNiMoN22-5-3 (EN) X2CrNiMoN25-7-4 (EN) X2CrNiMoCuN25-6-3 2205 S 322 05 2304 S 323 04 2506 S 312 60 2507 S 327 50 1. Japan AISI grade JIS grade 2205 QS 2205 Europe UNS designation S 318 03 EN / DIN numerical designation EN / DIN symbolical designation 1.4462 (EN) X2CrNiMoN22-5-3 1.4460 S 318 03 1. 7 .4507 S 312 00 1. 4418 (EN) X4CrNiMo16-5-1 1.4320 X2CrNiMo13-4 SUS 429 J1 431 SUS 431 440 A 440 C S 431 00 S 440 00 SUS 440 C S 440 04 SUS 440 F XM 12 S 155 00 1.4935 X20CrMoWV12-1 QD 51 QPD 5 Y 2L Y 2LF www.4034 (EN) X46Cr13 1.4028 (EN) X30Cr13 S 403 00 S 408 00 414 SUS 410 J1 410 S F6NM 416 SUS 416 S 416 00 SUS 416 HS2 SUS 416 L 416Se 420 420 SUS 420 J1 SUS 420 J2 SUS 420 J2C SUS 420 J2L 420 F SUS 420 F F3NM S 420 20 S 424 00 1.4006 (EN) X12Cr13 S 410 50 1. Japan AISI grade JIS grade 403 SUS 403 410 SUS 410 Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation S 410 00 1.weisz.4031 (EN) X39Cr13 1.4313 (EN) X3CrNiMo13-4 S 420 00 1.4116 (EN) X50CrMoV15 1.4030 S 415 00 1.4021 (EN) X20Cr13 S 420 10 1.com Steel grades equivalence tables Pág.4545 X5CrNiCuNb15-5-4 1.4021 (EN) X20Cr13 S 420 00 1.4006 (EN) X12Cr13 S 410 08 1.4122 (EN) X39CrMo17-1 1.][® Martensitic stainless steel USA. 8 .4922 X20CrMoV12-1 1. com Steel grades equivalence tables Pág. Japan AISI grade JIS grade Europe UNS designation F 91 EN / DIN numerical designation EN / DIN symbolical designation 1.][® High temperature martensitic stainless steel USA. Japan AISI grade JIS grade Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation 1.4913 X19CrMoVNbN11-1 1.weisz.4922 X20CrMoV12-1 Antimagnetic stainless steel USA.4903 X10CrMoVNb9-1 1. 9 .3951 X2CrNiMoN22-15 QMR 1L QMR 2L QMR 3L QMR 4L QMR 5L www. 10 .weisz. Japan AISI grade Europe JIS grade UNS designation 630 631 S 174 00 SUS 631 EN / DIN numerical designation EN / DIN symbolical designation 1.4539 (EN) X1NiCrMoCu25-20-5 Alloy 904 L QS 2025 MC Alloy 1925 HMO N 08 925 Alloy C-276 N 10 276 Alloy C-1008 Alloy C-1010 Alloy F 49 S 345 65 QS 2025 MT 1.4568 (EN) X7CrNiAl17-7 S 177 00 16-6 PH AM 350 AM 355 Alloy 15-5 PH Alloy 17-4 PH Alloy 17-7 PH Alloy 718 USS Stainless W High molybdenum alloy USA.][® Precipitation hardening stainless steel USA.4652 N 08 904 1.com Steel grades equivalence tables Pág.4532 (EN) X8CrNiMoAl15-7-2 1.4547 (EN) X1CrNiMoCuN20-18-7 Alloy 256 MO N 08 926 1.4583 X6CrNiMoN18-12 X1NiCrMoCuN20-18-7 www. Japan AISI grade Europe JIS grade UNS designation Alloy 29-4 EN / DIN numerical designation EN / DIN symbolical designation S 447 35 Alloy 29-4-2 Alloy 254 SMO S 312 54 1.4542 (EN) X5CrNiCuNb16-4 1.4565 X3CrNiMnMoNbN23-17-5-3 N 08 320 1.4529 (EN) X1NiCrMoCuN25-20-7 Alloy 654 SMO S 326 54 1. 4663 N 06 985 N 06 030 Alloy K-500 Alloy L-605 R 30 605 Alloy HX Alloy MP35N Alloy X QA X N 06 002 Alloy X-750 Alloy 6AC Alloy 6XN N 08 367 Alloy 20 Alloy 25 Alloy 31 N 08 031 1.4610 N 06 059 2.4605 Alloy C-276 QA C276 N 10 276 2.weisz.4602 2.][® High nickel alloy USA.com Steel grades equivalence tables Pág.4563 X1NiCrMoCu31-27-4 (EN) N 08 310 N 05 500 2.4375 Alloy B2 N 10 665 Alloy C4 N 06 455 Alloy CP Gr2 R 50 400 Alloy C22 N 06 022 2. Japan AISI grade JIS grade Europe UNS designation QS 20 Cb3 N 08 020 QS 2830 N 08 028 EN / DIN numerical designation EN / DIN symbolical designation 1.4819 Alloy G QA G N 06 007 N 06 617 Alloy G-3 QA G3 Alloy G-30 2.4640 NiCr15Fe Alloy 601 NCF 601 N 06 601 2. 11 .4851 NiCr23Fe Alloy 556 www.4360 NiCu30 Alloy 600 NCF 600 N 06 600 2.4816 NiCr15Fe Alloy 600 NCF 600 N 06 600 2.4562 Alloy 41XX Alloy 42 Alloy 43XX Alloy 52 Alloy 59 N 06 059 Alloy 188 Alloy 205 Alloy 220 Alloy 222 Alloy 230 Alloy 253 RMA Alloy 400 QA 400 N 04 400 2. 12 .4958 X5NiCrAlTi31-20 Alloy 800 NCF 800 N 08 800 1.4856 N 06 690 2.weisz.4558 X2NiCrAlTi32-20 Alloy 686 Alloy 690 JS 700 QS 2025 M Alloy 718 Alloy 800 NCF 800 Alloy 800 N 08 700 N 08 800 1.4973 NiCr19CoMo High temperature alloy USA.4877 2.4668 NiCr19NbMo N 08 800 1.4959 X8NiCrAlTi32-21 N 08 825 2.0882 CuNi30Mn1Fe 1.4864 X12NiCrSi36-16 Alloy 330 1.4958 X8NiCrAlTi32-21 N 08 811 1. Japan AISI grade JIS grade Europe UNS designation Alloy 602 EN / DIN symbolical designation 2.com EN / DIN numerical designation EN / DIN symbolical designation 1. Japan AISI grade JIS grade Europe UNS designation Alloy A 286 S 662 86 Alloy MP-35N R 30 035 Alloy X 750 N 07 750 Alloy 102 N 06 102 Alloy 253MA or F45 S 308 15 Alloy 330 N 08 330 Alloy 333 N 06 333 Alloy 617 N 06 617 www.4876 X10NiCrAlTi32-20 Alloy 800 H NCF 800 H N 08 810 1.4642 NiCr29Fe N 07 718 2.0872 Cupronickel 30 C 715 00 2.4835 Steel grades equivalence tables Pág.4858 NiCr21Mo CuNi10Fe Alloy 800 HT Alloy 825 NCF 825 N 08 840 Alloy 902 Cupronickel 10 C 706 00 2.][® High nickel alloy USA.4633 Alloy 622 Alloy 625 EN / DIN numerical designation N 06 622 QA 625 N 06 625 2. 7025 Titanium Gr 2 3. 13 .7235 Titanium Gr 11 3.5V Titanium Beta C Titanium Gr 1 3.4066 Nickel 201 N 02 201 2.][® Metals USA.4068 Nickel 270 www.4061 Nickel 200 N 02 200 2.7035 Titanium Gr 3 3.5Nb Hafnium Copper Nickel 200 Ni 200 N 02 200 2.7055 Titanium Gr 4 Titanium Gr 7 3.weisz. Japan AISI grade JIS grade Europe UNS designation EN / DIN numerical designation EN / DIN symbolical designation Titanium 3Al 2.4060 Nickel 201 Ni 201 N 02 201 2.com Steel grades equivalence tables Pág.7225 Titanium Cr 12 Titanium T40 Titanium T40 Gr2 Zircaloy 1 Zircaloy 2 Zirconium Zirconium 2. 2210 115CrV3 L2 100C3 107CrV3KU 1. Steel Werkstoff Germany U.7701 51CrMoV4 51CDV4 S60C C55K 1678 S55C S58C 51CrMoV4 Low-Alloy Steel.0503 C45 1045 CC45 080M46 C45 1650 F.5415 15Mo3 ASTMA204GrA 15D3 1501-240 16Mo3KW 2912 1. The use of these equivalents has to be evaluated on a case-by-case basis.12Cl.1545 C1051 C100KU SK3 1.2067 100Cr6 L3 Y100C6 BL3 1.0718 9SMnPb28 12L3 S250Pb 230M07 CF9SMn28 1912 11SMn28 SUM22 CF9SMnPb28 1914 11SMnPb28 SUM22L 1. Cast Steel.113 S35C 1.7362 12CrMo 19 5 1.S.7242 16CrMo 4 1. A18CrMo45KW Z10CD5. Free-Machining Steel 1.2241 51CrV4 1. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS Plain Steel.1158 Ck25 1025 XC25 070M25 C25 S25C 1.05 3606-625 16CrMo205 FE60-2 1055 070M55 C55 SM570 1655 S55C 1.1203 Ck55 1055 XC55 070M55 C50 1.114 S45C 1.7561 42CrV6 1.0535 C55 S35C C45K S50C 16Mo3 16Mo5 FE50 18CrMo4 S45C SB450M SM50YA 18CrMo4 A387Gr.0402 C22 1020 CC20 050A20 C20C21 1450 F.1213 Cf53 1050 XC48TS 060A52 C53 1674 1.0715 9SMn28 1213 S250 1.0070 St70-2 FE70-2 1.0332 St14 1008 1.112 1.2419 105WCr6 105WC13 10WCr6 2140 100Cr6 SUJ2 105WCr5 SKS31 .1545 C105W1 C100KU SK3 1.1191 Ck45 1045 XC42 080M46 C45 1672 1.1141 Ck15 1015 XC12 080M15 C16 1370 C15K 1. France Great Britain Italy Sweden Spain Japan No.7238 49CrMo4 1.1121 Ck10 1010 1.7337 16CrMo 4 4 1. Free-Machining Steel 1.0036 USt37-3 CC10 14491CR 1447 040A10 1264 S10C 210M15 S15C S15C FE37BFU 1.1221 Ck60 1060 XC60 080A62 C60 1.0401 C15 1015 CC12 080M15 C15C16 1350 F. Cast Steel.0060 St60-2 1.5423 16Mo5 4520 1503-245-420 16Mo5 1.1183 Cf35 1035 XC38TS 060A35 C36 1572 1.A.0501 C35 1035 CC35 060A35 C35 1550 F.111 1.0601 C60 1060 CC55 080A62 C60 1.MARYLAND METRICS Technical Data Chart A short general listing of popular materials International Material Grade Comparison Table The standards that correspond with DIN Material Numbers can only be compared approximately.0050 St50-2 1.0721 10S20 1108 1. 1191 Ck45 1045 XC42 080M46 C45 1672 1.7033 34Cr4 5132 1.5752 14NiCr14 3415.0503 C45 1045 CC45 080M46 C45 1650 F.2713 55NiCrMoV6 L6 55NCDV7 1.S SKH1.7220 34CrMo4 4137.7045 42Cr4 1.0332 St14 1008 1.112 S20C. Free-Machining Steel 1.0715 9SMn28 1213 S250 1.6657 14NiCrMo34 1.5622 1. DIN AISI/SAE UNS AFNOR BS UNI SS UNE 1.6523 21NiCrMo2 8620 20NCD2 805M20 20NiCrMo2 1.1121 Ck10 1010 1.2721 50NiCr13 1.0036 USt37-3 CC10 14491CR 1447 040A10 1264 S10C 210M15 FE37BFU 1.2762 75CrMoNiW67 1. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS Plain Steel.1158 Ck25 1025 XC25 070M25 C25 S25C 1.7035 41Cr4 1.2550 60WCrV7 S1 55WC20 1.7218 25CrMo4 4130 25CD4 1717CDS110 25CrMo4(KB) 2225 55Cr3 SM420.6587 17CrNiMo6 1.6546 40NiCrMo22 8740 1.0402 C22 1020 CC20 050A20 C20C21 1450 F. France Great Britain Italy Sweden Spain Japan No.A.SKT4 ~2550 O2 90MV8 BO2 88MnV8KU 100Cr6 52100 100C6 534A99 100Cr6 14Ni6 ASTMA350LF5 16N6 1.7176 55Cr3 5155 55C3 527A60 1.1141 Ck15 1015 XC12 080M15 C16 1370 C15K S15C 1.3505 1.2762 75CrMoNiW67 1.2842 90MnCrV8 1.A.6582 35CrNiMo6 4340 105WC13 107WCr5KU BS1 Japan JIS SKS31 45WCrV8KU 2710 58WCr9KU ~2710 45WCrSi8 F.3310 12NC15 655M13 1.Werkstoff Germany U. France Great Britain Italy Sweden Spain No.2542 45WCrV7 S1 1.6511 36CrNiMo4 9840 40NCD3 816M40 38NiCrM04(KB) 1.0721 10S20 1108 1. Cast Steel.0401 C15 1015 CC12 080M15 C15C16 1350 F.S22C 1.0718 9SMnPb28 12L3 S250Pb 230M07 CF9SMn28 1912 11SMn28 SUM22 CF9SMnPb28 1914 11SMnPb28 SUM22L 1.S.0501 C35 1035 CC35 060A35 C35 1550 F.4135 35CD4 708A37 35CrMo4 2234 34CrMo4 SCM432.1183 Cf35 1035 XC38TS 060A35 C36 1572 1.2419 105WCr6 1.520.7131 16MnCr5 35NCD6 18NCD6 2258 15Ni6 16NiCr11 15NiCr11 SNC415(H) SNC815(H) 311-TYPE7 40NiCrM02(KB) 817M40 35NiCrMo6(KB) 2506 33NiCrMo4 SNCM447 20NiCrMo2 SNCM220(H) 40NiCrMo2 2541 820A16 832M13 SUJ2 14Ni6 SNCM240 SNCM447 14NiCrMo13 15NiCrMo13 14NiCrMo131 32C4 530A32 34Cr4(KB) 35Cr4 SCR430(H) 5140 42C4 530M40 5140 42C4TS 530A40 41Cr4 2245 42Cr4 42Cr4 SCR440(H) SCr440 5115 16MC5 (527M20) 16MnCr5 2511 16MnCr5 SCR415 1.SCCRM3 Werkstoff Germany U.SCM430 SUP9(A) 1.5732 14NiCr10 3415 14NC11 1.114 S45C 1.1213 Cf53 1050 XC48TS 060A52 C53 1674 S35C C45K S45C S50C .113 S35C 1.111 S15C 1.S. 7242 16CrMo 4 1. France Great Britain Italy Sweden Spain Japan No.2721 50NiCr13 1.2550 60WCrV7 S1 55WC20 1.2542 45WCrV7 S1 1.2713 55NiCrMoV6 L6 55NCDV7 1. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS 1.2067 100Cr6 L3 Y100C6 BL3 100Cr6 1.5752 14NiCr14 3415.2842 90MnCrV8 1.A.S.7362 12CrMo 19 5 1.2762 75CrMoNiW67 1.7238 49CrMo4 1.2762 75CrMoNiW67 1.3310 12NC15 655M13 1.6587 17CrNiMo6 1.0070 St70-2 FE70-2 1.7045 42Cr4 1.2419 105WCr6 105WC13 10WCr6 1. Cast Steel.6582 35CrNiMo6 4340 SUJ2 107CrV3KU BS1 2140 105WCr5 SKS31 SKS31 45WCrV8KU 2710 58WCr9KU ~2710 45WCrSi8 F.0601 C60 1060 CC55 080A62 C60 1.5622 1.5732 14NiCr10 3415 14NC11 1.6523 21NiCrMo2 8620 20NCD2 805M20 20NiCrMo2 1.1545 C105W1 C100KU SK3 1.6546 40NiCrMo22 8740 1.5415 15Mo3 ASTMA204GrA 15D3 1501-240 16Mo3KW 2912 16Mo3 1.7033 34Cr4 5132 1. A18CrMo45KW Z10CD5.7035 41Cr4 1.0050 St50-2 1.1221 Ck60 1060 XC60 080A62 C60 1.0535 C55 16Mo5 FE50 18CrMo4 SB450M SM50YA 18CrMo4 A387Gr.2419 105WCr6 105WC13 107WCr5KU 1.5423 16Mo5 4520 1503-245-420 16Mo5 1.7131 16MnCr5 35NCD6 18NCD6 2258 15Ni6 16NiCr11 15NiCr11 SNC415(H) SNC815(H) 311-TYPE7 40NiCrM02(KB) 817M40 35NiCrMo6(KB) 2506 33NiCrMo4 SNCM447 20NiCrMo2 SNCM220(H) 40NiCrMo2 2541 820A16 832M13 SUJ2 14Ni6 SNCM240 SNCM447 14NiCrMo13 15NiCrMo13 14NiCrMo131 32C4 530A32 34Cr4(KB) 35Cr4 SCR430(H) 5140 42C4 530M40 5140 42C4TS 530A40 41Cr4 2245 42Cr4 42Cr4 SCR440(H) SCr440 5115 16MC5 (527M20) 16MnCr5 2511 16MnCr5 SCR415 .Werkstoff Germany U. Free-Machining Steel 1.12Cl.7337 16CrMo 4 4 1.520.2241 51CrV4 1.6511 36CrNiMo4 9840 40NCD3 816M40 38NiCrM04(KB) 1.7561 42CrV6 1.1545 C1051 C100KU SK3 1.2210 115CrV3 L2 100C3 1.7701 51CrMoV4 51CDV4 S60C C55K 1678 S55C S58C 51CrMoV4 Low-Alloy Steel.6657 14NiCrMo34 1.1203 Ck55 1055 XC55 070M55 C50 1.S SKH1.3505 1.05 3606-625 16CrMo205 FE60-2 1055 070M55 C55 SM570 1655 S55C 1.0060 St60-2 1.SKT4 ~2550 O2 90MV8 BO2 88MnV8KU 100Cr6 52100 100C6 534A99 100Cr6 14Ni6 ASTMA350LF5 16N6 1. Werkstoff Germany U.7733 24CrMoV55 1.45 1503-660-440 50CrV4 18NC13 13MoCrV6 51CrV4 SUP10 SUP10 640A35 SNC236 SNC631(H) 653M31 20CDV6 21CrMoV511 35NiCr9 SACM645 40CAD6.7755 GS-45CrMoV104 1.5736 36NiCr10 3435 30NC11 1.A.124.537 SKD62 1501.09 High-Alloy Steel. Cast Steel 1.5 1501-620-Gr27 14CrMo45 14CrMo45 SPVAF12 722M24 32CrMo12 2240 735A50 50CrV4 2230 735A50 51CrV4 2230 1. France Great Britain Italy Sweden Spain No.3501 100Cr2 E50100 100C2 1.7262 15CrMo5 1.4000 X6Cr13 F.7220 34CrMo4 4137.5755 31NiCr14 SNC836 1. Cast Steel 1.2606 X37CrMoW 51 H12 1.7223 41CrMo4 4140.2581 X30WCrV93 1.4135 35CD4 708A37 35CrMo4 2234 34CrMo4 SCM432.12 905M39 41CrAlMo7 897M39 36CrMoV12 2940 41CrAlMo7 X37CrMoV5 SKD6 2242 X40CrMoV5 SKD61 2312 X210CrW12 SKD2 X30WCrV9 SKD5 2310 X160CrMoV12 35CrMo8KU Z50CMNNb21.A 1501-622Gr31.5/4.3207 S10-4-3-10 1.8159 50CrV4 6150 1.SCM430 1.2436 X210CrW12 X215CrW121KU 1.7715 14MoV6 3 1.2344 X40CrMoV51 H13 Z40CDV5 BH13 X40CrMoV511KU 1.8509 41CrALMo7 1.S.3247 S2-10-1-8 Z110DKCWV09-08-04 1.22 SPV 2216 F. DIN AISI/SAE UNS AFNOR BS UNI SS UNE Japan 1.3202 S12-1-4-5 1. 50 X10Ni9 XBNi09 SL9N53 BT15 HS12-1-5-5 12-1-5-5 BT42 HS10-4-3-10 Z18N5 Z130WKCDV T15 SKD11 KCV06-05-05-04-02 HS6-5-2-5 SKH57 2723 1. Free-Machining Steel 1.5680 12Ni19 2515 1. SKH51 Stainless Steel.3246 S7-4-2-5 Z110WKCDV07-05-04 1.2601 X 165CrMoV12 H21 1.SCCRM3 JIS SUP9(A) Plain Steel.7218 25CrMo4 4130 25CD4 1717CDS110 25CrMo4(KB) 2225 55Cr3 SM420.3249 S2-9-2-8 M42 1.5662 X8Ni9 ASTMA353 1.2311 40CrMnMo7 1.5710 36NiCr6 3135 35NC6 1.7176 55Cr3 5155 55C3 527A60 1.2379 X155CrVMo121 D2 Z160CDV12 BD2 X155CrVMo121KU 1.7380 10CrMo9 10 1.7225 42CrMo4 4140 42CD4 708M40 42CrMo4 2244 42CrMo4 SCM440(H) 12CrMo4 SCM415(H) ASTMA182 15CD3.7335 13CrMo4 4 12CD4 1.3243 S6-5-2-5 Z30WCV9 BH21 X30WCrV93KU X165CrMoW12KU Z35CWDV5 BH12 X35CrMoW05KU F.3343 S6-5-2 M35 Z85WDCV BM2 HS6-5-2-5 2722 403 Z6C13 403S17 X6Cr3 2301 BM42 6-5-2-5 HS7-4-2-5 7-4-2-5 M35 HS2-9-1-8 2-10-1-8 M41 BM34 SKH55 SKH51 2-9-2-8 SKH9.7361 32CrMo12 1. Cast Steel.4142 42CD4TS 708M40 41CrMo4 2244 42CrMo4 SCM440 1.3110 SUS403 .8070 21CrMoV511 1.4882 X50CrMnNiNbN219 1.2343 X38CrMoV51 H11 Z38CDV5 BH11 X37CrMoV51KU 1.8159 50CrV4 6150 1.509.5864 35NiCr18 30CD12 ASTMA182F.8523 39CrMoV139 1. 4310 X12CrNi177 301 Z12CN17.4104 X12CrMoS17 430F Z10CF17 441S29 X10CrS17 2383 1.10 347S17 X6CrNiNb1811 2338 F.4086 G-X120Cr29 1.4541 X10CrNiMoTi1810 321 Z6CNT18.4762 X10CrA124 446 Z10CAS24 1.4027 G-X20Cr14 1.12 309S24 SUH309 .4301 X5CrNi189 304 Z6CN18.4724 X10CrA113 405 Z10C13 403S17 X10CrA112 F.4583 X10CrNiMoNb1812 318 Z6CNDN1713B 1.12 320S17 1.3543 SUS316 Z5CND20.4571 X10CrNiMoTi1810 316Ti Z6NDT17.3117 SUS430F SUS434 2376 Z40CM 420S45 Z6CNi6.4410 G-X10CrNiMo189 1.12 316S12 X2CrNiMo1712 2343/2348/2553 SUS316 1.4436 X5CrNiMo17133 316 Z6CND18-12-03 316S33 X8CrNiMo1713 2343/2347 SUS316 1.3524 SUS347 X6CrNiMoTi1712 2350 F.8401 410S.3401 1.3551 1.10M 347C17 1.4401 X5CrNiMo17122 316 Z6CND17.4002 X6CrAl13 405 Z8CA12 405S17 X6CrAl13 1.4016 X8Cr17 430 Z8C17 430S15 X8Cr17 2320 F.A.4429 X2CrNiMoN17133 316LN Z2CND17.3551 2327 F.Werkstoff Germany U. France Great Britain Italy Sweden Spain No. France Great Britain Italy Sweden Spain Japan No.4311 X2CrNiN1810 304LN Z2CN18.3113 SUS430 1.12 316S13 X2CrNiMo1712 2353 SCS16 1.3405 SUS431 X 105CrMo17 SUS440C Stainless Steel and Cast Iron Werkstoff Germany U. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS 1.4585 G-X7CrNiMoCuNb1818 1.09 304S15 X5CrNi1810 2332 F.4500 G-X7NiCrMoCuNb2520 1.4435 X2CrNiMo18143 316L Z2CND17.4113 X6CrMo17 434 Z8CD1701 434S17 X8CrMo17 2325 1.4350 X5CrNi189 304 Z6CN18.15 317S12 X2CrNiMo1816 2367 SUS317L 1. 429 SUS410 1.4550 X10CrNiNb 347 Z6CNNb18.11 316S16 X5CrNiMo1712 2347 1.13 316S63 X2CrNiMoN1713 2375 SUS316LN 1.02 431S29 Z100CD17 X16Cr26 2322 X40Cr14 2304 X16CrNi16 2321 SUH446 F.311 SUS405 1.4438 X2CrNiMo18164 317L Z2CND19.4006 (G-)X10Cr13 SUS410 Z10C13 410S21 X12Cr13 2302 F.4125 X105CrMo17 SCS2 452C11 S31500 431 F.4034 X46Cr13 1.9M 302C25 1.4362 X2CrNiN234 S32304 Z2CN23-04AZ 1.20M 1.S.10 321S12 X6CrNiTi1811 2337 F.3553F.4404 X2CrNiMo1810 316L Z2CND17.3552F.S.4742 X10CrA118 430 Z10CAS18 430S15 X8Cr17 F.12M 23NCDU25.07 301S21 X2CrNi1807 2331 F.4552 G-X7CrNiNb189 Z4CNNb19.4340 G-X40CrNi274 1.4720 X20CrMo13 1.09 304S31 X5CrNi1810 2332/2333 1.A.4001 X6Cr14 F.4417 X2CrNiMoSi195 1.4057 X20CrNi17 1.3523 SUS321 1.4312 G-X10CrNi188 Z10CN18.4828 X15CrNiSi2012 X6CrNiMoNb X6CrNiMoTi1712 309 Z15CNS20.4021 X20Cr13 420 Z20C13 420S37 X20Cr13 2303 Z20C13M 420C29 Japan SUS405 SUS430 SUS420J1 1. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS SUS304 Austenitic Stainless Steel 1.3517 1.3113 1.3535 SUS316TI SUS301 SUS304LN F.10 304S62 X2CrNiN1810 2371 1. 3 0.4345 AlZnMgCu0.5 3. DIN 3.331 SUH310.6015 GG15 CLASS25 Ft15D 0.6035 0.S.6040 FC100 GRADE150 G15 115 FG15 FC150 GRADE220 G20 120 FG20 FC200 Ft25D GRADE260 G25 125 FG25 FC250 CLASS45 Ft30D GRADE300 G30 130 FG30 FC300 GG35 CLASS50 Ft35D GRADE350 G35 135 FG35 FC350 GG40 CLASS55 Ft40D GRADE400 60-40-18 FCS400-12 SNG420/12 FGS370-17 SNG370/17 80-55-06 FGS500-7 SNG500/7 FGS600-3 SNG600/3 GGG60 0732-03 GGG60 FCD600 100-70-03 FGS700-2 SNG700/2 GGG70 0737-01 GGG70 FCD700 MB40-10 W410/4 GMB40 GTW40 GMB45 GTW45 140 FC400 Gray Cast Iron with Nodular Graphite 0.7033 GGG35.4462 X2CrNiMoN2253 S32900 Z2CND22-05-03 2324 1.S.7050 GGG50 0.8040 GTW-40 0. SUS310S Austenitic/Ferritic Stainless Steel (Duplex) 1.8035 GTW-35 0.6020 GG20 CLASS30 Ft20D 0.2373 G-AlSi9Mg 3.8155 GTS-55 0.Werkstoff Germany U.8065 GTW-65 0.8045 GTW-45 0.4821 X20CrNiSi254 Z20CNS25.04 1. 0864 GTS70 U.7060 GGG60 0.1754 G-AlCu5Ni1.2382 GD-AlSi10Mg .7070 GGG70 0717-15 GGG40 0717-02 FCD350 GGG40 0717-12 GGG50 0727-02 FCD400 FCD400 GGG50 FCD500 White malleable Cast Iron 0. DIN AISI/SAE UNS AFNOR BS UNI SS UNE Japan JIS 1.3315 AlMg1 GTW55 GTW65 MN35-10 B340/12 810 P440/7 852 GTS35 GTS45 MB35-7 W340/3 GTW35 50005 MP50-5 P510/4 GTS-65 70003 MP60-3 P570/3 856 GTS65 GTS-70 90001 M870-2 P690/2 0862.5 AZ4GU/9051 L86 811-04 7050 854 GTS55 Non-Ferrous Materials Aluminium Alloys 3. France Great Britain Italy Sweden Spain No.0255 Al99.7040 GGG40 0.6025 GG25 CLASS35 0.5 1000 3.8165 0.1655 AlCuSiPb 3. France Great Britain Italy Sweden Spain Japan AISI/SAE UNS AFNOR BS UNI SS UNE JIS A59050C L31/34/36 3.A.4845 X12CrNi2521 310S Z12CN2520 310S24 X6CrNi2520 2361 F.8135 GTS-35 32510 0.3 0.4823 G-X40CrNiSi274 SUS329J1 2977 Gray Cast Iron 0.A.6010 GG10 CLASS20 Ft10D G10 110 0.8170 Werkstoff Germany No.4460 X8CrNiMo275 1.8145 GTS-45 40010 0.8055 GTW-55 0.2381 G-AlSi10Mg 3.6030 GG30 0.7043 GGG40. 1188 G-CuPb20Sn C94100 U-Pb20 2.1050 G-CuSn10 C90700 2.0592 G-CuZn35Al1 C86500 U-Z36N3 HTB1 2. France Great Britain Italy Sweden Spain Japan No.1098 G-CuSn2ZnPb 2.2 LM9 4253 3.2383 GK-AlSi10Mg (Cu) A360.1052 G-CuSn12 C90800 CT1 UE12P Pb2 High-Temp Alloys Werkstoff Germany U.2371 G-AlSi7Mg 4218B 2.2383 G-AlSi10Mg (Cu) A360.S.1871 G-AlCu4TiMg 3.0596 G-CuZn34Al2 C86200 U-Z36N3 HTB1 2.1090 G-CuSn7ZnPb C93200 U-E7Z5Pb4 2. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS 3.4562 X1NiCrMoCu32287 N08031 1.1182 G-CuPb15Sn C93800 U-Pb15E8 LB1 2. CuZn37 CZ108 2.2 LM9 4253 3.0265 CuZn30 C26000 CuZn30 CZ106 2.0966 CuAl10Ni5Fe4 C63000 U-A10N Ca104 2.4864 X12NiCrSi 330 Z12NCS35.S.4958 X5NiCrAlTi3120 1.Werkstoff Germany U.4864 X12NiCrSi3616 N08330 Z12NCS35.1096 G-CuSn5ZnPb C83600 U-E5Pb5Z5 LG2 2.4558 X2NiCrAlTi3220 N08800 1.0321 CuZn37 C27200.3561 G-AlMg5 GD-AlSi12 3.0 3.4563 X1NiCrMoCuN31274 N08028 Z1NCDU31.16 1.2583 G-AlSi12 (Cu) A413.2582 GD-AlSi12 A413.27 1.5 MAG12 G-MgAl8Zn1 AZ81 G-A9 MAG1 3.5103 MgSE3Zn2Zr1 3.A.2581 G-AlSi12 A413.A.C2720 LB5 CC1-FF 2.0975 G-CuAl10Ni B-148-52 2. C27700 CuZn36.5101 G-MgZn4SE1Zr1 ZE41 3. France Great Britain US Sweden Spain Japan No.1293 CuCrZr C18200 U-Cr0.5106 3.0240 CuZn15 C23000 CuZn15 CZ102 2.1292 G-CuCrF35 C81500 Copper Alloys C2700.5912 G-MgAl9Zn1 AZ91 G-A9Z1 MAG7 2.5812 4247 A6061 LM20 4260 ADC12 A-SU 12 LN5 4252 AC4A G-Z4TR MAG5 EZ33 G-TR3Z2 MAG6 G-MgAg3SE2Zr1 QE22 G-Ag22. DIN AISI/SAE UNS AFNOR BS US Trade Designation SS UNE JIS NA15 Incoloy 800 Super-Alloys Fe-based 1.16 1.1 3.2 LM6 4261 3.1176 G-CuPb10Sn C93700 U-E10Pb10 LB2 2.8Zr CC102 2.4977 X40CoCrNi2020 Z42CNKDWNb SUH330 NA17 SUH330 . 4669 2. 509 Stellite 6. 21.9630 G-X300CrNiSi952 Ni.Hard 4 0.4810 G-NiMo30 N10276 2.4610 NiMo16Cr16Ti 2.4858 NiCr21Mo N08825 NC21FeDU NA16 Incoloy 825 2.7145 TiAl6Sn2Zr4Mo2Si R54620 3.4360 NiCu30Fe 2.7225 Ti1Pd 3.7025 Ti 1 3.7175 TiAl6V6Sn2 R56620 3.S. TA57 Hardened Materials Werkstoff Germany U.9625 G-X330NiCr42 Ni. 203-4 NC30Fe Nimonic 75 Inconel 690 2.Hard 1 Grade 2B 0513-00 0. 322.Werkstoff Germany U. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS 0.4856 NiCr22Mo9Nb N06625 NC22FeDNb Hastelloy C 2. France Great Britain Italy Sweden Spain Japan No.7165 TiAl6V4 R56400 3. 31 Super-alloys Ni-based 2.7124 TiCu2 3.4375 NiCu30 Al NU30AT NA18 Monel K-500 2.7195 TiAl3V2.A.7115 TiAl5Sn2 R52250 3.A.4668 NiCr19FeNbMo 2.9640 G-X300CrMoNi1521 .4630 NiCr20Ti 2.4642 NiCr29Fe NU30 NA13 Monel 400 Hastelloy C-4 N06075 NC20T HR5.9620 G-X260NiCr42 Ni. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS S66286 A-286 S41800 Greek Ascoloy R30556 Haynes 556 (HS556) R30155 N155 Super-Alloys Co-based R30188 Haynes 188 R30605 L605 (Haynes 25) MARM-302.5 R50250 2TA1 2TA21-24 3.7185 TiAl4Mo4Sn2 TP1 T-A6V TA10-13.4685 2. TA28 TiAl6V4 Ti6V6Al2Sn TA45-51.S. France Great Britain Italy Sweden Spain Japan No.Hard 2 Grade 2A 0512-00 0.4694 NA21 Inconel 625 N07718 NC19FeNb Inconel 718 NiCr15Fe7TiAl N07750 NC15TNbA Inconel X-750 G-NiMo28 N10001 Hastelloy B NiCr16Fe7TiAl N00751 Inconel 751 Titanium and titanium alloys 3.9635 G-X300CrMo153 White Cast Iron Hardened Cast Iron 0. 9650 G-X260Cr27 0.9645 G-X260CrMoNi2021 0.9655 G-X300CrMo271 0.A. France Great Britain Italy Sweden Spain Japan No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS 0.S.9655 G-X300CrMo271 copyright 2010 maryland metrics A532IIIA25%Cr Grade 3D A532IIIA25%Cr Grade 3E 0466-00 Data courtesy of Kennametal .Werkstoff Germany U.