ATR4518R14DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-M/M/M-R EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m Antenna Specifications Electrical Properties 3 x (1710 - 2690) Frequency range (MHz) 1710 - 1990 1920 - 2200 Polarization 2200 - 2490 2490 - 2690 +45° , -45° 0 - 12 , continuously adjustable, each band separately Electrical downtilt (°) at mid Tilt Gain (dBi) over all Tilts Side lobe suppression for first side lobe above main beam (dB) 17.6 18.0 18.4 18.6 17.4 ± 0.4 17.8 ± 0.4 18.1 ± 0.4 18.3 ± 0.5 > 19 > 22 > 20 > 19 Horizontal 3dB beam width (°) 66 ± 5.5 65 ± 4.2 64 ± 3.8 60 ± 3.2 Vertical 3dB beam width (°) 6.7 ± 0.5 6.1 ± 0.3 5.4 ± 0.4 5.0 ± 0.2 > 27 > 29 > 29 > 25 > 23 > 23 VSWR < 1.5 Cross polar isolation (dB) ≥ 30 Interband isolation (dB) ≥ 30 Front to back ratio, ± 30° (dB) Cross polar ratio (dB) > 27 > 26 0° Max. power per input (W) 250 (at 50℃ ambient temperature) Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier) Impedance (Ω) 50 Grounding DC Ground 1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA). 2. Electrical datasheet in XML format is available. 106 Mechanical Properties Antenna dimensions (H x W x D) (mm) 1365 x 376 x 99 Packing dimensions (H x W x D) (mm) 1680 x 440 x 170 Antenna weight (kg) 17.8 Clamps weight (kg) 3.0 (2 units) Antenna packing weight (kg) 27.5 (included clamps) 50 - 115 Radome material Fiberglass Radome colour Light grey Operational temperature (℃) -40 .. +65 Frontal: Lateral: Rear side: Wind load (N) 735 (at 150 km/h) 70 (at 150 km/h) 690 (at 150 km/h) Max. operational wind speed (km/h) 150 Survival wind speed (km/h) 200 Connector 6 x 7/16 DIN Female Connector position Bottom Accessories Item Model Description Weight Units per antenna Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 16 ° 1.9 kg 1 (Separate packing) 1 1262 1365 Mast diameter supported (mm) huawei. EN 55022 (Emission).0/3GPP and AISG 1. P. Facilities.. Longgang District. 12V) < 1. HUAWEI ‘s standard brackets and accessories must be used for any installation.5 (stand by.com/antenna Issue: 2015-06-29 . The protocol of RET antenna software interface is switchable between AISG 2. ETSI EN300386 (1. For more details about protocol switching function. WEEE Integrated RET S/N: HWMxxx. 3. EN 55024 (Immunity). contact Huawei before system installation.Yellow L . 4.Left array R . RoHS. FCC. The antenna working environment must meet the requirements specified in the datasheet.0 / 3GPP Input voltage range (V) 10 .Center array Pattern sample for reference NOTE 1710 .1..Right array C .yL HWMxxx…. Bantian. 2. 2 www. FCC part15 Certification: CE.4.yyyR y . Standards: EN 60950-1 (Safety).2690 MHz (Left) 1710 . 12V) Adjustment time (full range) (s) < 65 (typically. Ltd.yyC HWMxxx…. Shenzhen 518129.2690 MHz (Center) 1710 . such as towers and poles. Huawei Technologies Co.ATR4518R14 DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-M/M/M-R EasyRET Tri-Band Antenna with 3 Integrated RCUs .China Any previous datasheet issues become invalid.…. depending on antenna type) 2 x 8 pin connector according to IEC 60130-9 Daisy chain in: Male / Daisy chain out: Female RET connector Pin assignment according AISG 1 2 3 4 5 6 7 8 DC n/c RS-485B n/c RS-485A DC DC return n/c 3 (10/350 μs) 10 (8/20 μs) Lightning protection (kA) * Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface.2690 MHz (Right) 1.1).R. must bear the weight and wind load of antennas. Only qualified personnel are allowed to perform installation.1 with a vendor defined command.30 DC Power consumption (W) < 6 (motor activated.4m Integrated RET Specifications Properties RET type Integrated RET RET protocols* AISG 2. Installation tools and procedures must conform to requirements described in the antenna installation guide..