BO-139BODY INSTRUMENT PANEL BO4OU-01 REMOVAL CAUTION: Work must be started more than 90 seconds after the ignition switch is turned into the ”LOCK” position and the negative (-) terminal cable is disconnected from the battery. The SRS is equipped with a back-up power source. If work is started within 90 seconds from disconnecting the negative (- ) terminal cable of the battery, the SRS may be deployed. HINT: A bolt without a torque specification is shown in the standard bolt chart. (see page SS-2 ) Cover 1. REMOVE CENTER CLUSTER FINISH PANEL (a) Using a screwdriver, pry out the cover. HINT: Tape the screwdriver tip before use. H22781 (b) (c) Remove the 2 screws. Using a screwdriver, disengage the 4 clips and remove the center cluster finish panel. HINT: Tape the screwdriver tip before use. (d) w/ LEXUS navigation system: Disconnect the connectors. 4 Clips H22782 2. (a) REMOVE LOWER CENTER CLUSTER FINISH PANEL Using a screwdriver, disengage the 2 clips and remove the lower center cluster finish panel. HINT: Tape the screwdriver tip before use. (b) Disconnect the connectors. 2 Clips 2005 LEXUS IS300 (RM1140U) H15130 Author : Date : 2376 disengage the 2 clips and remove the upper console panel as shown in the illustration. (a) w/ Arm rest: REMOVE CONSOLE BOX Using a screwdriver. HINT: Tape the screwdriver tip before use. (a) (b) REMOVE UPPER CONSOLE PANEL M/T: Remove the shift lever knob. Disconnect the connectors. 3 Claws 2005 LEXUS IS300 (RM1140U) H22783 Author : Date : 2377 . 2 Clips H19273 5. Using a screwdriver. (a) (b) (c) w/o Arm rest: REMOVE CONSOLE BOX Remove the 6 screws. HINT: Tape the screwdriver tip before use. w/o LEXUS navigation system: Pull the console box rearward to remove it. then disconnect the connector. disengage the 3 claws and remove the box side No. disengage the 2 clips and remove the parking brake hole cover. H15131 4. 2 panels.BO-140 BODY INSTRUMENT PANEL 3. w/ LEXUS navigation system: Pull the console box rearward to remove it. (a) (b) REMOVE A/C CONTROL WITH RADIO RECEIVER ASSEMBLY Remove the 4 bolts and A/C control with radio receiver assembly. 2 Clips H15133 6. H15134 7. REMOVE PARKING BRAKE HOLE COVER Using a screwdriver. HINT: Tape the screwdriver tip before use. 1 and No. (c) Disconnect the connector. Remove the 4 bolts and rear console armrest hinge. H22934 (d) (e) (f) (g) H19279 Remove the 6 screws.) H22935 (c) Remove the console box cover rear. 22 ft·lbf. H15685 9. then disconnect the connector. disengage the connector clamp. H15136 2005 LEXUS IS300 (RM1140U) Author : Date : 2378 . (b) Disconnect the passenger airbag connector. NOTICE: When disconnecting the airbag connector.BO-141 BODY INSTRUMENT PANEL (b) Remove the 2 bolts and remove the console compartment door. Torque:30 N·m (306 kgf·cm. DISCONNECT PASSENGER AIRBAG CONNECTOR (a) Using a clip remover. w/ LEXUS navigation system: Pull the console box rearward to remove it. w/o LEXUS navigation system: Pull the console box rearward to remove it. REMOVE GLOVE COMPARTMENT DOOR Disconnect the hinge shaft and remove the glove compartment door. take care not to damage the airbag wire harness. 8. 4 Clips H15715 17.5 N·m (56 kgf·cm. disengage the 4 clips and remove the cluster finish panel. 49 in. HINT: Tape the screwdriver tip before use. REMOVE STEERING WHEEL PAD (See page SR-13 ) 12. (c) Disconnect the connectors and hood lock control cable. Using a screwdriver. 11. S Never disassemble the front passenger airbag assembly.·lbf) for nut CAUTION: S Do not store the front passenger airbag assembly with the airbag deployment side facing down. (a) (b) REMOVE CLUSTER FINISH PANEL Remove the 2 screws. Using a screwdriver. 3 Clips H23154 16. REMOVE SPIRAL CABLE (See page SR-13 ) 15.BO-142 BODY INSTRUMENT PANEL H15137 10. Torque: 20 N·m (205 kgf·cm. 15 ft·lbf. disengage the 3 clips and remove the lower finish panel. 2 nuts and the passenger airbag assembly from the instrument panel. (a) (b) REMOVE LOWER FINISH PANEL Remove the 3 screws. REMOVE STEERING WHEEL (See page SR-13 ) 13. (a) (b) REMOVE COMBINATION METER Remove the 3 screws and combination meter.) for bolt 5. HINT: Tape the screwdriver tip before use. H15716 2005 LEXUS IS300 (RM1140U) Author : Date : 2379 . REMOVE FRONT PASSENGER AIRBAG ASSEMBLY Remove the 2 bolts. REMOVE COLUMN UPPER AND LOWER COVERS (See page SR-13 ) 14. Disconnect the connector. 5 Clips H23155 20. (d) Remove the bolt. Torque: 9. REMOVE COWL SIDE TRIM BOARD LH (a) Remove the clip. HINT: Tape the screwdriver tip before use. REMOVE FRONT DOOR INSIDE SCUFF PLATE RH HINT: Use the same procedures described for the LH side..·lbf) Clip H19277 (e) 24. REMOVE FRONT PART OF FRONT DOOR OPENING TRIMS H15718 23. remove the pillar garnish cover. 21.8 N·m (100 kgf·cm. remove the pillar garnish. (b) Remove the bolt. 87in. (a) REMOVE FRONT DOOR INSIDE SCUFF PLATE LH Using a screwdriver. (c) Using a screwdriver. HINT: Use the same procedures described for the LH side. REMOVE COWL SIDE TRIM BOARD RH HINT: Use the same procedures described for the LH side. (b) Pull the cowl side trim board rearward to remove it.BO-143 BODY INSTRUMENT PANEL 18. HINT: Tape the screwdriver tip before use. REMOVE FRONT PILLAR GARNISH RH H19278 2005 LEXUS IS300 (RM1140U) Author : Date : 2380 . 22. 19. disengage the 5 clips and remove the front door inside scuff plate. REMOVE FRONT PILLAR GARNISH LH (a) Using a screwdriver. Cover the airbag with protective cover as shown in the illustration. NOTICE: Be careful not to damage the instrument panel and wire harness H15720 2005 LEXUS IS300 (RM1140U) Author : Date : 2381 . (c) Remove the 3 bolts. (b) Disengage the wire harness clamps.BO-144 BODY INSTRUMENT PANEL 25. 2 screws and 2 nuts. (d) Pull the instrument panel rearward to remove it. REMOVE INSTRUMENT PANEL (a) Disconnect the connectors. (f) Remove the bolt<D> and No. 2 mounting bracket. (g) Remove the 4 bolts<E> and No.BO-145 BODY INSTRUMENT PANEL 26. 1 mounting bracket. 1 brace. Remove the bolt<F> and ground cable. instrument panel reinforcement and the lower mounting bracket. 1 Mounting Bracket 2005 LEXUS IS300 (RM1140U) Author : Date : 2382 . H19472 Instrument Panel Reinforcement <F> <D> No. 2 nuts. (h) Remove the 5 bolts. Remove the bolt<B>. 1 Brace Panel to Floor Brace Lower Molding Bracket H23169 <E> <B> <B> No. (a) (b) (c) (d) REMOVE INSTRUMENT PANEL REINFORCEMENT Disengage the wire harness clamps. Remove the 2 bolts <A> and LH lower pad insert. screw<B> and No. 2 Mounting Bracket <E> <C> <A> LH Lower Pad Insert No. (e) Remove the bolt<C> and panel to floor brace. NOTICE: Be careful not to damage the body and wire harness.