JCY-1700/SVDR /S-VDR VD CYC-232A CYC 232A Playback Software / Real Time Monitor Instruction Manual Version 2.0 Introduction ＜Introduction＞ Thank you for using the Playback software for our VDR/S-VDR equipment. This software is intended to help analyze the data recordings that are stored in a PC card of VDR/S-VDR installed onboard. This software chronologically plays back all the data including the radar image, bridge and VHF communication audios recorded in VDR/S-VDR. - Before using the software, read this manual thoroughly to ensure correct use. Keep the manual in a convenient location so that it can be used easily whenever necessary. Use this manual to check the operation of the software or at the occurrence of a fault. Microsoft, MS-DOS, and Windows are the registered trademarks of Microsoft Corporation in the U.S.A and / or other countries. Pentium is the trademark of Intel Corporation. The names of actual companies and products mentioned herein are the trademarks of their respective owners. Attention (1) The copyright of this software and a manual is in Japan Radio Co., Ltd. (2) The range as which the Copyright Act determines a part or all of the contents of this and a manual cannot be exceeded, and it cannot reproduce without notice. (3) Although we created to make doubly sure about the contents of this book, if there is a thing of companion mind, such as a doubtful point, and an error, omission in written, please contact me. (4) Please understand beforehand that it is not concerned with (3) clauses and any responsibility cannot be taken about the claim of the loss for reasons of the employed result, loss profits, etc. in our company. software Playback Software / Real Time Monitor Instruction Manual i and to prevent damage to the property.Before Using ＜Before Using＞ Icons This manual and product employ various icons to enable users to use the product safety and correctly. or a Incorrect use of the equipment by ignoring this icon may cause an injury or physical damage. The symbol indicates prohibition. Example of icons The △ symbole indicates a caution (including danger or warning). and to prevent any harm to users or others. WARNING CAUTION Incorrect use of the equipment by ignoring this icon may cause death seruous injury. Inside of the symbol indicates the actual details (this icon indicates the Electric shock caution regarding electric shock). The actual contenst (this Remove Plug icon indicates removal of the power plug from socket) are provided inside of Instruction the symbol Playback Software / Real Time Monitor Instruction Manual ii . The actual contents (this icon indicates “disassembly prhibited”) are provided Disassembly prohibited Prohibited inside or alongside of the symbol The ● symbol indicates an action or insutruction. The icons and the meanings are indicated below. When a fault occurs. Do not check or repair the inside of the equipment by yourself. and failure. or a small metal thing on this equipment top or near. or an equipment fault. Do not put containers into which it went.. and contact the Sales Department of Japan Radio Company. remove the plug. nearest branch company. branch office. such as water. Such action may cause fire. sales office. it becomes the cause of a fire. turn off the power supply of this equipment. sales office. a power cord will be damaged and it may become the cause of fire and electric shock. Such action may cause burst of a battery by liquid leak. it pulls or it bends by force. heat. or injury. Do not use any AC/DC adaptor other than attachment. Do not damage a power cord or process it. electric shock. Continuous use may cause fire or electric shock. Playback Software / Real Time Monitor Instruction Manual iii . If put a heavy thing. or an equipment fault. Request checking or repair of the inside of the equipment to the sales Department of Japan Radio Company. electric shock. fire. When water enters or a metal thing falls into the equipment. an electric shock. Such action may cause fire. nearest branch company. Do not use any battery other than specification. Do not use any power supply voltage other than the specified voltages. or our agent. electric shock. branch office. or an equipment fault.Notes on Using < Notes on Using > Do not disassemble or remodel this equipment. Such action may cause fire. Checking or repair by anyone other than the specialist maintenance staff may cause fire or electric shock. or our agent. such as metal or a thing which is easy to burn. Pull out a plug from a wall socket for safety at the time of care. It may become the cause of electric shock. It may become the cause of fire or electric shock. If a computer is infected with a virus. It may become the cause of fire or electric shock. or a fault. When the equipment is not used for a long time. Playback Software / Real Time Monitor Instruction Manual iv . Do not plug up the vent of this equipment. and may become the cause of failure. it may suffer the damage of an unusual display. or a fault. and data being destroyed. or soot. electric shock. electric shock. using a virus checker program periodically. dust. Please confirm whether it is infected with the computer virus. Do not wet this equipment or do not put in water. humidity. It may become the cause of fire. It may become the cause of fire. It may be filled with heat and fire and failure may occur. Do not put in from a vent foreign substance. a program.Notes on Using CAUTION Do not install the equipment in the location affected by water. Be careful of a computer virus. or a fault. pull out a power supply plug from a wall socket for safety. It may fall and may become the cause of an injury and failure. Do not put on a place with many vibration and shocks. .............3 Setting playback time by [Clock] button .. i ＜Before Using＞ ................................................................................................................7 To set playback time ..................1 PC specification.........3 2........................................................................40 4............................................................................................................................................................................................... ii < Notes on Using > ............................................................................................... 33 3............. 1 Chapter2 Install Playback software...48 4................................................................................................... 3 2...................................48 Playback Software / Real Time Monitor Instruction Manual v ........5 To play back PC card data...................................................4 Playback Operation Panel ....1 How to start up Playback software ..................... 39 4..................................................................................2 How to exit Playback software..................................................................................... iii Chapter1 Outline..33 Chapter4 Operation ......................................................................................................................................................................41 4.................................43 4.........47 4........................................................47 4..................................................2 Set required information for playback with the Setup software......................................................33 3............................2 How to install .........................................................................3 How to uninstall ....................................................................................................................................................................................................................30 Chapter3 Setup for Playback software ............ and to stop .......................................................................39 4......7............................................................7.............................................................................................................................................1 Setting playback time by Slide bar ............7...44 4.............................................................................................................................................................................2 Setting playback time by [Forward] button or [Rewind] button .....Contents ＜Contents＞ ＜Introduction＞...................................4 2..........................6 To start playback................................47 4...1 Create a playback folder..........................................3 Playback screen ................................................................. ...............................................................78 4.....77 4...................................................................................................................................................................2......................19............13........................................................13....78 4...........................................................13.....................................................19......2 Numeric screen............................................................................10 Voyage screen.........................................................................60 4..................49 4.....................................19............19......................................................................................2 Menu bar....61 4.....................................................................3 Record Stop or Pause.............................51 4.......16 To confirm the VDR/S-VDR system information ...2 Record for a Long Time ..1 Record Setup ..............2........63 4..........................................2 Record Start .........13..................62 4............................................................................81 4..............................................68 4..........................................................19......................................................................................Contents 4.................................50 4.................82 4............................................59 4......................................................................12.............................................................52 4........................................................2...15 To print screen ......................................................................................................................................................................................................................................61 4.........19.............................................4 To playback recorded data .......................................................9 To adjust Volume and select audio source ............................1 Graphic screen ...............................79 4............................................................71 4.........67 4..............................11 Alarm/Status screen..................................................................17 How to customize screen layout..................................19 Optional Function ...........12 Radar screen.................................73 4.....................1 Real Time Indication ......65 4.....................................79 4..............................................................................1 Icon ...........................10.........................................................................................................................................................................................2...14 To confirm the record sentences in the NMEA format ........................8 To change a playback speed .................................12.......................13 AIS Screen............58 4...83 Playback Software / Real Time Monitor Instruction Manual vi ...........................................18 How to restore to initial screen layout..2 List screen ..............................................................................................................................................................1 Graphic screen ...................................................................4 Detail information of AIS target ......3 Detail Information of own ship.............................70 4..............................................................66 4....................10.. ..............................86 5.........................................................................98 Playback Software / Real Time Monitor Instruction Manual vii ................3 Converting a part of recorded data ......................................................... 95 7..................................91 Chapter6 Trouble Shooting....................................................... 85 5..................................2 Convert all recorded data..................................................................Contents Chapter5 Converting Recorded Data into Industry Standard Formats........................................1 How to eject PC card from VDR/S-VDR .........................................4 C onverted files (Industry Standard Formats Files) ........................................................................................................................................................................95 7..........89 5...........................................85 5........................... 93 Chapter7 Appendix ..........2 Sentence and indication place..............................................1 Starting conversion software................................................ Contents Blank Page Playback Software / Real Time Monitor Instruction Manual viii . by connecting with shipboard LAN. you can see the Real Time Monitor in a sitting room.Chapter1 Outline Chapter1 Outline This software intends to be used for playing back recorded data required the International Standard in a PC card of VDR/S-VDR equipment. branch office. Record data ・Sensor data ・Bridge audio and VHF communication ・Radar image As an optional function. And real time data can be indicated and recorded by Real Time Monitor side for a long time. Further as an expanded function. sales office. or our agent. nearest branch company. contact the Sales Department of Japan Radio Company. In the case of requirement. Playback Software / Real Time Monitor Instruction Manual 1 . and the data can be played back. this software is extended as real time monitor by making LAN connection with VDR/S-VDR. Chapter1 Outline Blank Page Playback Software / Real Time Monitor Instruction Manual 2 . 6GHz or Higher Windows XP Windows Vista / Windows 7 HDD Display Resolution CD drive Card drive Network : : : : : Minimum 40GB 1024×768 dots (Recommend XGA) CD-ROM PCMCIA TypeⅡ 10BASE-T/100BASE-TX Ethernet Minimum 512MB Minimum 1GB Playback Software / Real Time Monitor Instruction Manual 3 . OS : Windows XP Professional or Home Edition Windows Vista (SP1) Windows 7 CPU RAM : : Minimum Pentium M Processor730 1.Chapter2 Install Playback software Chapter2 Install Playback software 2.1 PC specification Confirm the following system requirement on your PC. please operate from (4). click “SetupE. refer to Note on next page.exe” after selecting the CD drive by My Computer. (1) Insert the Install CD-ROM in a CD drive.2 How to install Install the Playback software in a PC in accordance with the following operation. Installer starts and the following web screen opens automatically by AUTORUN. And then operate from (3).Chapter2 Install Playback software 2. (If the installer does not start. ) The following contents are possible to refer in the web screen. (2) After a while. To continue installation. For the instruction on how to install in PC of Windows Vista and after. Note ・ ・ ・ ・ ・ Playback Software / Real Time Monitor instruction manual CSV Conversion instruction manual JCY-1700 VDR instruction manual JCY-1700S S-VDR instruction manual CD license number Playback Software / Real Time Monitor Instruction Manual 4 . Select “Open folder to view files.Chapter2 Install Playback software The Instruction of how to install in Windows Vista and Windows 7 PC Note ・ In order to install Playback Software. AUTORUN function starts up and the following screen displays. then the installer starts up. For Windows XP Select ”Allow” by left-clicking it. [Yes] button Playback Software / Real Time Monitor Instruction Manual 5 . ・ Insert Installation CD-ROM in CD drive. then the installer starts up.exe in the folder by left-clicking it. always login PC as administrator.” Open folder to view files ・ Run SetupE. After a while. then the following confirmation screen for execution displays. and execute the installation. Allow For Windows 7 Press [Yes] button. (5) The Install Shield Wizard for the Playback software starts.Chapter2 Install Playback software (3) The preparation for the installation are started. (4) The opening screen is indicated. and click [Next] button. and click [Next] button. Playback Software / Real Time Monitor Instruction Manual 6 . which is described in the install CD-ROM to the Serial Number field. Note License number is composed by “jrc－＊＊＊＊－＊＊＊＊”. And enter the License number. and progress bar is indicated. Playback Software / Real Time Monitor Instruction Manual 7 .Chapter2 Install Playback software (6) Customer Information screen is indicated. (8) Install is started. and click [Install] button. Please enter user information in the User Name field and the Organization field. (7) The confirmation screen where the installation folder and user information are shown is indicated. Network and Internet Connection Playback Software / Real Time Monitor Instruction Manual 8 . disable the firewall function on your PC in accordance with the following procedure. and keep the Installation CD-ROM carefully. Control Panel ・Click “Network and Internet Connection”. (11) Since Playback software partially uses network communication. and then click “Control Panel” in Start menu. (10) Please eject the Install CD-ROM from the CD drive. ●For Windows XP ・Click [Start] button. and click [Finish] button.Chapter2 Install Playback software (9) The Install Shield Wizard completion screen is indicated. Chapter2 Install Playback software ・Click “Windows Firewall” Windows Firewall ・Select “Off (not recommended)”. and click [OK] button. Off (not recommended) Playback Software / Real Time Monitor Instruction Manual 9 . Control Panel ・Click “Security”. Off (not recommended) Playback Software / Real Time Monitor Instruction Manual 10 . Security ・Click “Turn Windows Firewall on or off”. and click [OK] button. Turn Windows Firewall on or off ・Select “Off (not recommended)”.Chapter2 Install Playback software ●For Windows Vista ・Click [Start] button and then click “Control Panel”. Turn Windows Firewall on or off Playback Software / Real Time Monitor Instruction Manual 11 .Chapter2 Install Playback software ●For Windows 7 ・Click [Start] button and then click “Control Panel”. System and Security ・Click “Windows Firewall”. Control Panel ・Click “System and Security”. Windows Firewall ・Click “Turn Windows Firewall on or off”. Chapter2 Install Playback software ・Select “Turn off Windows Firewall (not recommended)”. and click [OK] button. Turn off Windows Firewall (not recommended) Playback Software / Real Time Monitor Instruction Manual 12 . Chapter2 Install Playback software (12) Set power option so that your PC does not enter system standby (sleep) or hibernation while operating Playback software. ●For Windows XP ・Click “Performance and Maintenance” on Control Panel screen. Performance and Maintenance ・Click “Power Option”. Power Option ・ Select ”Never” under “Plugged in” of “Turn off hard disks”, “System standby”, and “Hibernation” on “Power Schemes” tab and click [OK] button. Never Playback Software / Real Time Monitor Instruction Manual 13 Chapter2 Install Playback software ●For Windows Vista ・Click “System and Maintenance” on Control Panel screen. System and Maintenance ・Click “Change when computer sleeps”. Change when computer sleeps ・Click “Change advanced power setting”. Change advanced power setting Playback Software / Real Time Monitor Instruction Manual 14 Chapter2 Install Playback software ・Select ”Never” for ” Plugged in” of “Hard disk”, “Sleep after”, and “Hibernate after” and click [OK] button. Hard disk Sleep after Hibernate after Playback Software / Real Time Monitor Instruction Manual 15 Chapter2 Install Playback software ●For Windows 7 ・Click “System and Security” on Control Panel screen. System and Security ・Click “Power Options”. Power Options ・Click “Change plan settings”. ・Click “Change when computer sleeps”. Change plan settings Playback Software / Real Time Monitor Instruction Manual 16 . ”Sleep after” and “Hibernate after” to “Plugged in Never”. Turn off hard dick after Sleep after Hibernate after Playback Software / Real Time Monitor Instruction Manual 17 . Change advanced power settings ・Set “Turn off hard dick after”.Chapter2 Install Playback software ・Click “Change advanced power settings”. click [OK] button. set as follows so that PC does not enter sleep mode when closing the lid. Select “Do nothing” under “When I close the lid of my portable computer” and click [OK] button. Power Option ・Select “Advance” tab. Performance and Maintenance ・Click “Power Option”. Advance tab When I close the lid of my portable computer Playback Software / Real Time Monitor Instruction Manual 18 . ●For Windows XP ・Click “Performance and Maintenance” on Control Panel screen.Chapter2 Install Playback software (13) For notebook or laptop PC. Chapter2 Install Playback software ●For Windows Vista ・Click “Mobile PC” on Control Panel screen. Change what closing the lid does ・Select “Do nothing” under “Plugged in” of “When I close the lid” and click [Save changes] button. When I close the lid Playback Software / Real Time Monitor Instruction Manual 19 . Mobile PC ・Click “Change what closing the lid does”. Chapter2 Install Playback software ●For Windows 7 ・Click “System and Security”. Choose what closing the lid does ・Set “When I close the lid” to “Do nothing”. click [Save changes] button. When I close the lid [Save changes] button Playback Software / Real Time Monitor Instruction Manual 20 . System and Security ・Click “Choose what closing the lid does”. Playback software might not display correctly. Time.Chapter2 Install Playback software (14) If the operating system (OS) on your PC is not Japanese or English version. Language. Time. Language. Please set language to "English (United States)" or "English (United Kingdom)" as follows. and Regional Options” on Control Panel screen. Regional and Language Options Playback Software / Real Time Monitor Instruction Manual 21 . and Regional Options ・Click “Regional and Language Options”. ●For Windows XP ・Click “Date. Date. Chapter2 Install Playback software ・Select “Regional Option” tab and select “English (United States)” or “English (United Kingdom)”. then click [OK] button. Select “English (United States)” or “English (United Kingdom)” ”. and then restart it. Regional Option tab English (United States) or English (United Kingdom) ・Select “Advanced” tab. You will be asked to restart Windows. Advance tab English (United States) or English (United Kingdom) Playback Software / Real Time Monitor Instruction Manual 22 . Regional and Language Options Playback Software / Real Time Monitor Instruction Manual 23 .Chapter2 Install Playback software ●For Windows Vista ・Click “Clock. and Region” on Control Panel screen. Language. and Region ・Click “Regional and Language Options”. Language. Clock. Format tab English (United States) or English (United Kingdom) ・Select “Administrator” tab.Chapter2 Install Playback software ・Select “Format” tab and select “English (United States)” or “English (United Kingdom)”. Click [Change system locale] button. and then click [OK] button. and select “English (United States)” or “English (United Kingdom)”. You will be asked to restart Windows. and then restart it. Administrator tab [Change system locale] button Playback Software / Real Time Monitor Instruction Manual 24 . and then click [OK] button. and Region ・Click “Regional and Language Options”.Chapter2 Install Playback software ●For Windows 7 ・Click “Clock. Click [Change system locale] button. Administrative [Change system locale] button Playback Software / Real Time Monitor Instruction Manual 25 . and select “English (United States)” or “English (United Kingdom)”. You will be asked to restart Windows. Language. Regional and Language ・Select “Administrative” tab. Clock. and Region” on Control Panel screen. and then restart it. Language. Chapter2 Install Playback software (15) For Windows Vista PC or Windows 7 PC. ●For Windows Vista ・Right-click the “JCY-1700 VDR Monitor” icon on desktop. Compatibility tab Playback Software / Real Time Monitor Instruction Manual 26 . since Playback software has to start by the administrator user continually. ・Select “Properties”. set as follows. Properties ・Select “Compatibility” tab. select "Allow" and start the software. and click [OK] button. After installation also. Allow Playback Software / Real Time Monitor Instruction Manual 27 . always login as administrator user and use Note Playback software. since the confirmation screen is displayed at starting Playback software.Chapter2 Install Playback software ・ Input “✓” mark in “Run this program as an administrator” under “Privilege Level”. In addition. Privilege Level The setup for Windows Vista PC is completed above. ・Select “Properties”. Properties ・Select “Compatibility” tab.Chapter2 Install Playback software ●For Windows 7 ・Right-click the “JCY-1700 VDR Monitor” icon on desktop. Compatibility tab Playback Software / Real Time Monitor Instruction Manual 28 . and click [OK] button. In addition. Yes Playback Software / Real Time Monitor Instruction Manual 29 . click [Yes] and start the software. Privilege Level The setup for Windows 7 PC is completed above. After installation also. since the confirmation screen is displayed at starting Playback software. always login as administrator user and use Note Playback software.Chapter2 Install Playback software ・ Input “✓” mark in “Run this program as an administrator” under “Privilege Level”. 3 How to uninstall Uninstall the Playback software in your PC in accordance with the below operation. JCY-1700 VDR Monitor ・Since some files remain in the installation folder after completing the uninstallation. ●For Windows XP ・Click [Start] button and click “Control Panel” in Start menu. Add or Remove Programs ・Select the JCY-1700 VDR Monitor and click [Remove] button. Control Panel ・Click “Add or Remove Programs”.Chapter2 Install Playback software 2. Installation folder: C:\Program files\JRC\JCY1700\VDR_Monitor Playback Software / Real Time Monitor Instruction Manual 30 . open My Computer and delete the folder. Installation folder: C:\Program files\JRC\JCY1700\VDR_Monitor (32bits OS) C:\Program files (x86)\JRC\JCY1700\VDR_Monitor (64bits OS) Playback Software / Real Time Monitor Instruction Manual 31 . Control Panel ・Click “Uninstall a program”. Uninstall a program ・Click “JCY-1700 VDR Monitor”. JCY-1700 VDR Monitor ・Click [Yes] button. open My Computer and delete the folder. ・Since some files remain in the installation folder after completing the uninstallation.Chapter2 Install Playback software ●For Windows Vista ・Click [Start] button and click “Control Panel” in Start menu. JCY-1700 VDR Monitor ・Click [Yes] button. Control Panel ・Click “Programs”. open My Computer and delete the folder. Programs ・Click “JCY-1700 VDR Monitor”. Installation folder: C:\Program files\JRC\JCY1700\VDR_Monitor (32bits OS) C:\Program files (x86)\JRC\JCY1700\VDR_Monitor (64bits OS) Playback Software / Real Time Monitor Instruction Manual 32 .Chapter2 Install Playback software ●For Windows 7 ・Click [Start] button and click “Control Panel” in Start menu. [Yes] button ・Since some files remain in the installation folder after completing the uninstallation. 2 ③ Start the Playback software. ⇒Refer to 3. Playback data is copied to the folder made here. the Playback software does not work. C:\MV JRC ↑ E. And in order to play back recorded data of PC card.1 ② Set required information for playback with the Setup software.1 and 4. [SETUP] button Playback Software / Real Time Monitor Instruction Manual 33 .5 3. ⇒Refer to 4. click [SETUP] button. The icon is created automatically after installation. start My Computer. it is necessary to create a playback folder in the computer of use advance. If setup is not completion. Ship name 3. (2) To start up the Setup software.Chapter3 Setup for Playback software Chapter3 Setup for Playback software Setup is necessary before playing back the VDR/S-VDR data recorded on the PC card. and to copy the data. (2) Create a folder as follows. ① Create a playback folder in certain location before Setup. Shows the flow from setup to playback below. and copy a recorded data of PC card. ⇒Refer to 3.1 Create a playback folder (1) To create a playback folder.g.2 Set required information for playback with the Setup software (1) Click the JCY-1700 VDR Monitor icon on the desktop. Playback Software / Real Time Monitor Instruction Manual 34 . User (4) The “Setup for User” screen displays.Chapter3 Setup for Playback software (3) The “Log in” screen displays. and click [OK] button after confirming that “User” is selected in “Operator” block. and insert it into PC card slot on your PC. [Import] button ＊: \Init\SysInfo. PC card drive differs depending on your PC. (6) Check quantity of engine.1 How to eject PC card from VDR/S-VDR”. Click [Import] button and select the following file in the PC card in order to import VDR configuration information (SysInfo.dat file is not imported. be sure to follow the operation of “7. Note If the [Import] button is clicked and a SysInfo.dat). thruster and propeller and others which were imported by VDR/S-VDR configuration data. which were registered when VDR/S-VDR was installed. rudder. The PC card may be damaged and record may not be available. the [Set] button do not become valid.Chapter3 Setup for Playback software (5) Eject a PC card from VDR/S-VDR.dat PC card drive Caution When a PC card is ejected from the VDR/S-VDR. Quantity Playback Software / Real Time Monitor Instruction Manual 35 . To close the Setup software.Chapter3 Setup for Playback software (7) Click Folder Selection button. and select the folder created at Section 3. click [Close] button. Folder Selection button (8) Click [Set] button.1. and setup is completed. Playback Software / Real Time Monitor Instruction Manual 36 . C:\JRC_VDR_Data） Playlist1： for Real Time Monitor Playlist1 VDR Init Log Audio Visual Playlist2 VDR Playlist2～10： For Copying from PC Card Init Log Audio Visual Playlist10 Playback Software / Real Time Monitor Instruction Manual 37 . Playback Folder（e.Chapter3 Setup for Playback software (9) When setup is completed.1 is formatted as the following folder structure.g. the playback folder created at Section 3. Chapter3 Setup for Playback software Blank Page Playback Software / Real Time Monitor Instruction Manual 38 . [MONITOR] button (3) Playback screen is indicated.Chapter4 Operation Chapter4 Operation 4. Playback Software / Real Time Monitor Instruction Manual 39 . (2) Click [MONITOR] button on the Launcher menu.1 How to start up Playback software (1) Click the JCY-1700 VDR Monitor icon on the desktop. Chapter4 Operation 4.2 How to exit Playback software (1) Click [Setup] button of bottom right in the playback screen and the Setup screen is indicated. (4) The Playback screen is closed and it returns to the Launcher menu. [Exit] button (3) Click [OK] button in the Confirm window. Playback Software / Real Time Monitor Instruction Manual 40 . [Setup] button (2) Click [Exit] button of bottom left in the Setup screen. Playback Operation Panel and Menu Block. Status Block.Chapter4 Operation 4. Main Block Status Block Playback Operation Panel Menu Block Playback Software / Real Time Monitor Instruction Manual 41 .3 Playback screen The Playback screen is composed with Main Block. Chapter4 Operation The Playback screen has Voyage screen. Alarm/Status screen. and their screens are selected with buttons of the Menu Block. AIS screen does not display when AIS is not connected to VDR/S-VDR. AIS screen and Radar screen on the Main Block. Voyage Alarm/Status Menu Block AIS Radar Playback Software / Real Time Monitor Instruction Manual 42 . Note) Audio is not outputted at playback of ×2 and ×4. Shows a playback time. Available to forward a playback time fast. ⑪ ⑫ ⑬ ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ Slide bar select button Available to select time span of slide bar for playback time. Available to reverse a playback time fast. ”×2” and “×4”. Available to select a playback time from the calendar. Available to select a playback speed from “×1”. Available to start playback. Name OLDEST time LATEST time Slide bar Playback time Clock button Playback button Stop button Rewind button Forward button Playlist button Speaker button Playback Speed Function Show the oldest time of the recorded data. Show the latest time of the recorded data. Playback Software / Real Time Monitor Instruction Manual 43 . ① ② ⑩ ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ No.4 Playback Operation Panel Shows the function of buttons and sections. Available to select audio source and adjust volume. Available to stop playback. Available to playback after selecting a voyage data registered in the playlist. Available to playback from a certain time by sliding the knob.Chapter4 Operation 4. (5) Select a playlist in the Copy place box. Caution When a PC card is ejected from the VDR/S-VDR. (2) Click Playlist button. If 1hour is selected. Playlist button (3) Confirm the PC Card drive is set in the Copy source. 1 hour data from the latest is copied.1 How to eject PC card from VDR/S-VDR”. Shows how to copy below.Chapter4 Operation 4. The PC card may be damaged and record may not be available. and insert it in the PC card slot. Seize selection Copy source Copy place Folder Select button [Copy] button Playback Software / Real Time Monitor Instruction Manual 44 . and click [Copy] button.5 To play back PC card data In order to play back. (1) Eject a PC Card from VDR/S-VDR. If the drive is not set. it is necessary to copy the data of a PC card after the playlist 2. please be sure to follow the operation of “7. (4) Select copy size from 1 hour to 12 hours or All in the Size selection. please click Folder Select button and select the drive. and then the copy starts.Chapter4 Operation Since the comment dialog appears. Playback Software / Real Time Monitor Instruction Manual 45 . It takes time to copy all data (In case of copying the “All”) for 15 minutes. and enter some comments if required. Note The entered comments are indicated in the Comment field. Click [OK] button. please be sure to insert a PC card to the VDR/S-VDR. and click [OK] button. and it is possible to play back with [Playback] button. Caution When data copying is finished. “MEDIA ERROR” occurs in the VDR/S-VDR. “MEDIA ERROR” occurs in the VDR/S-VDR. The alarm is canceled automatically when the PC card is inserted in the VDR/S-VDR. Please press [ACK] button in the VDR/S-VDR to stop the alarm. Playlist radio button (7) The setup is completed above. If the PC card is continued to eject more than 10 minutes. Playback Software / Real Time Monitor Instruction Manual 46 .Chapter4 Operation Caution If the PC card is continued to eject more than 10minutes. (6) Select radio button of the playlist copied PC card data. click [Stop] button. click [Playback] button. a playback time is forwarded or reversed according to the position.Chapter4 Operation 4. moreover. So it is easy to adjust playback time. In that case.1 Setting playback time by Slide bar If knob is slid. Note Playback time span of the Slide bar becomes long. And time span of Slide bar for playback time can be selected with Slide bar select button. and so it is not easy to adjust playback time. and to stop To start playback. time span becomes long.7 To set playback time Explain how to set playback time. Stop Playback 4.6 To start playback. Playback time span becomes 12 hours. And to stop playback. select the 12 hours in the Slide bar select button. Slide bar select button Slide bar Playback time Slide bar If recorded data for some days is played back.7. 4. scale in every hour is displayed. Playback Software / Real Time Monitor Instruction Manual 47 . If [Rewind] button is pressed. And the step time is increased by pressing the button continuously. (3) Click [OK] button.2 Setting playback time by [Forward] button or [Rewind] button If [Forward] button is pressed. Forward button Rewind button Playback time 4. playback time can be skipped to latest time.7.7. Playback Software / Real Time Monitor Instruction Manual 48 . [Oldest Skip] button [Latest Skip] button Slide bar If [Oldest Skip] button is clicked. a playback time is forwarded. (A light green part shows that there is recorded data. playback time can be skipped to oldest Note time.3 Setting playback time by [Clock] button (1) Select a date you want to play back from calendar. slide the knob of the Slide bar. And step time is increased by pressing the button continuously.Chapter4 Operation 4.) (2) To select time. And if [Latest Skip] button is clicked. a playback time is reversed. time span is 12 hours after Note selected playback time. the playback speed become 2 times faster than normal. If “×2” is selected.) If 12 hours of slide bar select button is set.Chapter4 Operation (4) Selected date is indicated in the Playback time Slide bar select button Playback time (5) Click [Playback] button.8 To change a playback speed To change a playback speed. 4. playback is restarted automatically without clicking [Playback] button. the playback speed become 4 times faster than normal. “×1” is selected as default. Playback speed Playback Software / Real Time Monitor Instruction Manual 49 . So it becomes easy to select playback time with slide bar. (If playback is in progress. Moreover if “×4” is selected. select it from the Playback speed. the playback speed is normal. Audio data cannot be played back at "X2" or "X4" speed. Audio Source Volume All Mute If audio is not outputted in playback. Moreover if the All mute is clicked and enter the “✓” mark. please confirm audio volume level Note and mute selection in the Sound and Audio Device Properties which is opened from the Control Panel of PC.9 To adjust Volume and select audio source If [Speaker] button is clicked.Chapter4 Operation 4. If exclude an unnecessary audio source. slide up or down the volume knob. click the source and remove the “✓” mark. Speaker To adjust volume. Playback Software / Real Time Monitor Instruction Manual 50 . the Volume control screen appears. all sources are muted. 10 Voyage screen There are the Graphic screen and the Numeric screen in the Voyage screen.Chapter4 Operation 4. Graphic screen Numeric screen Voyage Playback Software / Real Time Monitor Instruction Manual 51 . click [Voyage] button in the Menu block. To change the screens. Invalid indication 4.10.C” displays when the input equipment is not connected. if [True/Relative] button is clicked. [True/Relative] button Playback Software / Real Time Monitor Instruction Manual 52 . Moreover.1 Graphic screen The following explains Graphic screen. Since VDR/S-VDR usually records only data of relative value. it changes to true indication (top is the north) or relative indication (top is head of a ship). Moreover.Chapter4 Operation 4. “*” mark displays when data in numeric indication are not recorded.10. it becomes an invalid indication when all the items in the divided block have not been connected.1.1 Wind block This block shows wind speed and wind direction by numeric and graphic. “N. only relative value displays. 3 Heading block This block shows heading graphically and numerically by Gyro.Chapter4 Operation 4. The following figure is an example in case there is one rudder.1. And the blue line shows heading by Gyro.10.2 Rudder direction and heading block This block shows heading against rudder direction by graphic.10. Rudder direction Heading 4.1. Playback Software / Real Time Monitor Instruction Manual 53 . The green line shows rudder. The following figure is an example in case there are 1 propeller and 1 rudder.Chapter4 Operation 4.4 Ship block (Voyage screen) This block shows status of propeller. rudder and speed by numeric and graphic under voyage.1.5 Ship block (Docking screen)” about the Docking screen. Refer to “4. Voyage screen [Voyage/Docking] button Playback Software / Real Time Monitor Instruction Manual 54 . If [Voyage/Docking] button is clicked.10.10.1. the Ship block is switched to the Docking screen. 1. the Ship block is switched to the Voyage screen.10. speed and thruster by numeric and graphic under docking. Refer to “4.10. If [Voyage/Docking] button is clicked.5 Ship block (Docking screen) This block shows status of propeller.4 Ship block (Voyage screen)” about the Voyage screen. Docking screen [Voyage/Docking] button Playback Software / Real Time Monitor Instruction Manual 55 .Chapter4 Operation 4. The following figure is an example in case there are 1 propeller.1. rudder. 1 rudders and 1 thruster. 6 Voyage Info block This block shows date. by numeric. time. Playback Software / Real Time Monitor Instruction Manual 56 .1.10. own ship’s position etc.Chapter4 Operation 4. 8 Engine Telegraph block This block shows engine telegraph status by graphic. and the light-blue zone is underwater.10.1.10. The brown zone is seabed. A horizontal axis shows lapsed time and shows the depth of water of the newest at right end.7 Depth block This block shows Depth by numeric and graphic.Chapter4 Operation 4.1. Underwater Seabed 4. Telegraph Position Sub-Telegraph Position Operating Location Controlled engine or shaft Playback Software / Real Time Monitor Instruction Manual 57 . “N.10. “*“ mark displays if data in numeric indication have not yet received or illegal data are inputted.2 Numeric screen In numeric screen. Playback Software / Real Time Monitor Instruction Manual 58 .Chapter4 Operation 4.C” displays when the input equipment is not connected. all data of graphic screen are showed in numeric. This screen is composed 3 blocks of Alarm/Status.g. status of engine telegraph. To show door status e. And if [Section] button is clicked. the Alarm/Status information is sorted. Alarm/Status Category Menu Alarm/Status Menu Section button Playback Software / Real Time Monitor Instruction Manual 59 . door status. Category Menu and Alarm/Status Menu.. Moreover.. water level and fire detection etc. click [Door] button from the Alarm/Status Menu.Chapter4 Operation 4.11 Alarm/Status screen The Alarm/Status screen shows alarm information. to show about Steering gear e. click the Steering gear from the Category Menu.g. it is possible to view maximum 4 images.Chapter4 Operation 4. Playback Software / Real Time Monitor Instruction Manual 60 . If Radar Interfaces (Option Unit) are added. It is prepared so that the icon and the menubar may effectively view the radar screens.12 Radar screen It is possible to view a Radar image captured every 15 seconds in this screen. Chapter4 Operation 4. Name Zoom Out Zoom In Tile Close Print Cascade Function Available to contract a selected radar screen. Available to arrange radar screens like tiles. 4.12.1 Icon”. ① ② ③ No. ④ ⑤ ⑥ ① ② ③ ④ ⑤ ⑥ Available to arrange radar screens in forward and backward.12.2 Menu bar Shows the composition of the menu bar below.1 Icon Shows the function of buttons below. Available to print a selected radar screen. File Zoom Out Zoom In Print Close Window Tile Cascade Playback Software / Real Time Monitor Instruction Manual 61 . Available to close the radar screen. Available to expand a selected radar screen. The functions are same as icons of “4.12. Graphic screen Simple Information List Screen Graphic / List Graphic/ List button Playback Software / Real Time Monitor Instruction Manual 62 . click [Graphic] button or [List] button. And simple information of own ship and AIS targets is indicated on right side. To select the screens.13 AIS Screen There are the Graphic screen and List screen in the AIS screen.Chapter4 Operation 4. (Radius: from 0. Screen area is expanded or contracted by the Range button.13. the state of AIS target is indicated on graphics by a symbol.Chapter4 Operation 4.75 to 24 nm) Range button Playback Software / Real Time Monitor Instruction Manual 63 .1 Graphic screen Centering on own ship. Chapter4 Operation Explains about symbols in the following table. If position report of a ship is not received more than a certain time. Category Own ship Symbol Explain ・Solid line shows heading. AIS Base Station Aids-to -navigation Mouse cursor Playback Software / Real Time Monitor Instruction Manual 64 . ・ Dashed line shows COG(Course Over Ground). ・ Dashed line shows COG(Course Over Ground). AIS Target ・Solid line shows heading. the symbol is indicated. 2 List screen Position report.13.Chapter4 Operation 4. IMO number. call sign and length of hull etc are showed in this screen. ship's name. It is indicated on near order from a top from own ship. Playback Software / Real Time Monitor Instruction Manual 65 . Chapter4 Operation 4.13. the detail screen is indicated.3 Detail Information of own ship If [Detail] button in the simple information block. Playback Software / Real Time Monitor Instruction Manual 66 . Chapter4 Operation 4.13.4 Detail information of AIS target If [Detail] button in the simple information block. the detail screen is indicated. Playback Software / Real Time Monitor Instruction Manual 67 . Chapter4 Operation 4.14 To confirm the record sentences in the NMEA format Available to confirm the record sentences in the NMEA format on the Dump screen. To open the Dump screen, operate as follows. (1) Click [Setup] button in the Menu Block. [Setup] button (2) Select the Maintenance tab in the setup and click [View] button. Maintenance tab [View] button Playback Software / Real Time Monitor Instruction Manual 68 Chapter4 Operation (3) Select a port No. in the combo box and click To view the record NMEA sentences, click [Start] button. To abort view, click [Stop] button. Shows the function of buttons below. ④ ③ ② ① ⑤ ⑥ No. Name Port No. Start Clear Stop Dump screen Close Function Available to select a certain channel or all channels. Available to start view. Available to clear NMEA sentences on the Dump screen. Available to abort view. NMEA sentence is shown on the screen. Available to close the Dump screen. ① ② ③ ④ ⑤ ⑥ Playback Software / Real Time Monitor Instruction Manual 69 Chapter4 Operation 4.15 To print screen To print screen, click [Print] button in the MENU Block. [Print] button Note To print, it is necessary to install a printer driver in a used PC beforehand. Playback Software / Real Time Monitor Instruction Manual 70 [Setup] button (2) Click [View Info] button. (1) Click [Setup] button in the Menu Block and select the Version tab. operate as follows.Chapter4 Operation 4. [View Info] button Playback Software / Real Time Monitor Instruction Manual 71 . To open the VDR/S-VDR System Information screen.16 To confirm the VDR/S-VDR system information Available to confirm the VDR/S-VDR system configuration that is required in the International Standard on the VDR/S-VDR System Information screen. Available to show the DAU1 system information on the screen. ① ② ③ ④ Playback Software / Real Time Monitor Instruction Manual 72 . Available to show the DAU2 system information on the screen. Name RCU DAU1 DAU2 Close Function Available to show the RCU system information on the screen. Shows the function of buttons below. Available to close the screen. ③ ② ① ④ No.Chapter4 Operation (3) The VDR/S-VDR System Information screen is opened. Chapter4 Operation 4. and if a check mark of "Dialog" is removed.17 How to customize screen layout It is possible to move. And when [Setup] button is clicked.g. Course Tab e. setting tabs of each block are indicated.) Dialog [Exit] button (1/4) Tab Course Bar Corresponding Block Note Climate Ship (Voyage) － Not used Playback Software / Real Time Monitor Instruction Manual 73 . please change Dialogs on the Voyage2 screen. Therefore it is possible to indicate necessary blocks only. The screen layouts are saved automatically at exiting the Playback software. If the Voyage2 screen is changed. a layout of the Voyage1 screen is changed. the corresponding block disappears. When Dialogs are changed on the Voyage1 screen. expand and reduce the Voyag1 and Voyage2 screens. Chapter4 Operation (2/4) Tab Ship (Docking) Corresponding Block Note Radar ・ Initially this block is shown on the Voyage2 screen only. Current / Wind Voyage Info Playback Software / Real Time Monitor Instruction Manual 74 . ･It is possible to change a graph range in addition to selection of visible and invisible. but shows how to correct time. Engine Graph ･ Initially this block is not shown. Engine Telegraph Time Correction － ･There is no corresponding block. If needed. ･It is possible to select “KELL” mode or “WATER/TRANS/KEEL” mode. Playback Software / Real Time Monitor Instruction Manual 75 . Heading / Rudder ･It is possible to change a graph range in addition to selection of visible and invisible. ･ Initially this block is shown on the Voyage1 screen only. change the dialog.Chapter4 Operation (3/4) Tab Depth Graph Corresponding Block Note ･It is possible to change a graph range in addition to selection of visible and invisible. Playback Software / Real Time Monitor Instruction Manual 76 .Chapter4 Operation (4/4) Tab AIS Corresponding Block Note ・ It is possible to change AIS target number and range in the AIS screen. System ・It is possible to select blue or black for background color. If the Voyage1 screen is restored. Those operations are omitted in this manual.Chapter4 Operation 4. Playback Software / Real Time Monitor Instruction Manual 77 . click [Restore] button after opening the Voyage1 screen. click [Restore] button on the Voyage2 screen.18 How to restore to initial screen layout It is possible to restore to initial screen layout by [Restore] button in the Maintenance tab. [Save] button ※ [Restore] button [Reread] button ※ ※ [Save] and [Reread] buttons are used by a service person. If the Voyage2 screen is restored. 1 Real Time Indication (1) Confirm that the “Live” of the Status block goes out. the “Play” of the Status block lights up green. Shows the operation below.19.Chapter4 Operation 4. or our agent 4. (4) The "Live" lights up yellow. it is already becoming a real-time indication. a real time indication and record for a long time are available as Real Time Monitor. Note It is possible to change to playback indication with [Live/Play] button. contact the Sales Department of Japan Radio Company. Note Standard function of the Playback software is playback only. so that it is unnecessary to operate as follows. Playback Software / Real Time Monitor Instruction Manual 78 . If you require the real time indication and record for a long time. (3) The Confirmation screen of indication clear. In case of playback. click [OK] button. by making LAN connection with VDR/S-VDR. When "Live" is lighting up yellow. and it changes to real time indication.19 Optional Function As an optional function. branch office. sales office. nearest branch company. (2) Click the [Live/Play] button in the Menu block. If it is good. 4.2.19.1 Record Setup It is necessary to set a record folder or a record period. [SETUP] button (2) Click [Folder Selection] button in the Setup Folder. refer to the “3.2 Record for a Long Time The capacity of HDD required in order to record for a long time changes with a record period and contents of record. Folder Selection button Playback Software / Real Time Monitor Instruction Manual 79 . and select a record folder. Please purchase a HDD after asking our company the capacity. Before select the record folder. To create the playback folder. before starting record. In that case.1 Create a playback folder”. Starts the Setup software from the Launcher menu to set them.0. purchase external HDD of the USB version 2.19. (1) Click [SETUP] button on the Launcher menu. please create the folder with the My Computer.Chapter4 Operation 4. (5) To close the Setup software. Playback Software / Real Time Monitor Instruction Manual 80 . the “Setup OK” screen is indicated. oldest data is overwritten by newest data. The record setup is completed. (4) Click the [Set] button. click [Close] button. When the setup is completed.Chapter4 Operation (3) Set a record period in the Record block About Overwrite) When there is the check in the Overwrite and a record period is exceeded. (3) The “REC” in the Status block lights up red. and click [REC] button after check. data is effluence. Playback Software / Real Time Monitor Instruction Manual 81 . and record is started. lack may arise in recorded data. Therefore.2 Record Start (1) Click [Backup] button in the Menu block. Even if it misses data. (2) Since a record folder and free space of a HDD are indicated. data are not resent. The record by the Real Time Monitor records data which the Note VDR/S-VDR outputs by a UDP protocol. On an UDP protocol. There may be no data in recorded data at that time.Chapter4 Operation 4.2.19. (2) When record is stopped. When record is paused. click [STOP] button.Chapter4 Operation 4. click [PAUSE] button.19.3 Record Stop or Pause (1) Click [Backup] button in the Menu block. and the record is stopped or paused.2. (3) The “REC” in the Status block goes out. Playback Software / Real Time Monitor Instruction Manual 82 . Then restart the Real Time Monitor. Playlist button When a LAN cable of the Real Time Monitor is disconnected for playing Note back in another sitting room. Exit the Real Time Monitor once. and press [Disconnect] button in the Ethernet tab.19. To play back the recorded data. Start the Setup software. In that case.4 To playback recorded data The recorded data by the Real Time Monitor are saved in the Playlist1. Playback Software / Real Time Monitor Instruction Manual 83 . select the Playlist1 in accordance with the following operation.Chapter4 Operation 4. the playback is not possible.2. press [Connect] button with the same operation. (1) Click [Play List] button. and it is possible to play back. When the LAN cable is connected again. g. and click [OK] button. C:\JRC_VDR_Data） Record to here Playlist1： for Real Time Monitor VDR Init Log Audio Visual Playlist1 Playlist2 Playlist2～10： For Copying from PC Card Playlist10 Playback Software / Real Time Monitor Instruction Manual 84 .Chapter4 Operation (2) Select the Playlist1. Record Place Note Playback Folder（e. [CONVERT] button (2) Conversion software screen displays.Chapter5 Converting Recorded Data into Industry Standard Formats Chapter5 Converting Recorded Data into Industry Standard Formats 5.3.2. (3) Method for conversion Refer to Section 5.1 Starting conversion software (1) Click [CONVERT] button. Refer to Section 5. when partially converting recorded data Playback Software / Real Time Monitor Instruction Manual 85 . when converting all recorded data. so that conversion software starts up. 2 Convert all recorded data (1) Click Folder Selection button in Source Folder. Folder Selection Note Playback Folder (e. [Folder Selection] button Select the “*\Playlist2\VDR”. C:\JRC_VDR_Data） Playlist1 VDR Init Log Audio Visual Playlist2 VDR Init Log Audio Visual Select here Playlist10 Playback Software / Real Time Monitor Instruction Manual 86 .Chapter5 Converting Recorded Data into Industry Standard Formats 5.g. and select “VDR” folder in the folder that recorded data are saved. and select “Convert_Data” folder as the destination of converted files. (3) Click Folder Selection button in “Convert Folder”. Folder Selection button Select the “\Convert_Data” on desktop. "Convert_Data" folder was created as an example. Here.Chapter5 Converting Recorded Data into Industry Standard Formats (2) Create any folder for saving converted files on desktop. Playback Software / Real Time Monitor Instruction Manual 87 . [Convert] button (5) Stop converting Click [Cancel] button in order to stop converting. converted files are indicated in list box. Playback Software / Real Time Monitor Instruction Manual 88 .Chapter5 Converting Recorded Data into Industry Standard Formats (4) Click [Convert]. progress of conversion is indicated in progress bar. Also. W hen conversion starts. Recorded data that can be partially converted are single file. all files in the folder are converted. the progress of conversion is indicated in progress bar. * Refer to next page for the example operation.3 Converting a part of recorded data (1) Click Folder Selection button in “Convert Folder”. two or more files. When a folder is selected. Folder Selection button (2) Drag and drop a part of recorded data into list box.Chapter5 Converting Recorded Data into Industry Standard Formats 5. Playback Software / Real Time Monitor Instruction Manual 89 . W hen conversion starts. and select “Convert_Data” folder as the destination of converted files. conversion operation by drag and drop is not available. or two or more folders. Also. (3) Conversion starts automatically. converted files are indicated in list box. Note In case of Windows Vista and Wnidows7. single folder. Playback Software / Real Time Monitor Instruction Manual 90 . conversion operation by drag and drop is not available.Chapter5 Converting Recorded Data into Industry Standard Formats Drag & Drop Note In case of Windows Vista and windows7. R1.????????.DD. CH2 and CH3 Mix MIC-CH4.hhmmss.????????. (If IMO number is not entered. automatically converts to “99999999”.wav Note Mix MIC-CH1.????????.V1.????????.M1.wav YYMMDD.M2.4 Converted files (Industry Standard Formats Files) The conversion software creates converted files as follows.????????.????????.R2.????????.txt YYMMDD.M3.wav YYMMDD. CH8 and CH9 Mix VHF-CH1.hhmmss.hhmmss.) Playback Software / Real Time Monitor Instruction Manual 91 .hhmmss. Data Digital Sensor Data Audio File Name YYMMDD. CH5 and CH6 Mix MIC-CH7.hhmmss.png YYMMDD.hhmmss.wav YYMMDD.Chapter5 Converting Recorded Data into Industry Standard Formats 5. Ch2 andCH3 Main Radar Sub Radar Radar Display Video YYMMDD.hhmmss.png YYMMDD: Date hhmmss: Time (UTC) ????????: IMO No. Chapter5 Converting Recorded Data into Industry Standard Formats Blank Page Playback Software / Real Time Monitor Instruction Manual 92 . Adjust the Volume or invalidate the Mute. Please contact us in that case. Turn on the power of the VDR Interface. The Power of a captured display is not turned on. Check the connections. Playback Software / Real Time Monitor Instruction Manual 93 . Audio volume of the Windows or is low. please confirm the contents of this chapter before contact us No. The setup by our serviceman is necessary. the setup by our serviceman is necessary. 3 There are no audio outputs of the real time. Faulty wiring of the external HDD The power of the external HDD power is not turned on. Cause Faulty wiring of a LAN cable The power of the VDR/S-VDR Interface is not turned on. 2 The image indication is not possible. the setup by our serviceman is necessary. Or mute is validated. To monitor. To record. 6 The image recording is not possible The image recording is not as set necessity. Adjust the Volume or invalidate the Mute in the “Volume Control” and “Wave”. To record. 4 The record is not possible. 1 Symptom The real time indication is not possible. The audio recording is not necessary. the monitoring may be prevented. Please contact us in that case. Audio volume of the Playback software is low. Or mute is validated. Turn on power of a captured display. Please contact us in that case. Audio monitoring is not Action Check the connections. 5 The audio recording is not possible. Turn on the power of the external HDD. On private.Chapter6 Trouble Shooting Chapter6 Trouble Shooting If the Real Time Monitor may be not normal or occur a error. validated. 19. The pressed and operation is in the state of LAN connection. 8 When a LAN cable of the Real Time Monitor is disconnected. Action Increase a free space by deleting unnecessary data. Playback Software / Real Time Monitor Instruction Manual 94 .Chapter6 Trouble Shooting No.4. or exchange to a mass HDD [Connect] button is In order to operate under disconnecting the LAN.2. Cause The free space of the HDD is not enough for the record period. the playback is not possible. 7 Symptom Record data are less than a record period. Refer to 4. please press the [Disconnect] button in the Setup software. Chapter7 Appendix Chapter7 Appendix 7.1 How to eject PC card from VDR/S-VDR Please unlock the key and open the door. Key Internal Operation Panel Playback Software / Real Time Monitor Instruction Manual 95 . Then ejection of PC card becomes possible. (3) Push the [EJECT] button. PC CARD LED（Green） MEDIA ERROR LED（Red） BACKUP STOP button EJECT button PC CARD SLOT Playback Software / Real Time Monitor Instruction Manual 96 .Chapter7 Appendix Please operate the Internal Operation Panel as follows. and eject a PC card. (1) Push the [BACKUP STOP] button. (2) The PC CARD LED blinks for 5sec and goes out. Caution When a PC card is inserted to the VDR/S-VDR. If the LED does not light up. Please contact us in that case. the PC card may be faulty.Chapter7 Appendix Caution When data copying is finished. the PC CARD LED lights up and record into the PC card is restarted. Playback Software / Real Time Monitor Instruction Manual 97 . If the PC card is continued to eject more than 10 minutes. “MEDIA ERROR” occurs in the VDR/S-VDR. please be sure to insert a PC card to the VDR/S-VDR. x xx.2 Sentence and indication place (1/4) Screen Block Section Data Indication Voyage1 Voyage2 （Graphic） Relative Wind True Wind Direction Wind Speed Wind Direction Wind Speed Rudder direction Rudder and heading Heading Heading Ship (Voyage) True STW (Water-reference) SOG (Ground-reference) Propeller Pitch Starboard Port Revolution Starboard Port Rudder Starboard Port Starboard Port True xxx.x Thruster Pitch Revolution Propeller Pitch Starboard Port Revolution Starboard Port Rudder Starboard Port xxx. m/s deg(°) kt.x Unit deg(°) kt.x xxx.x xxx.x xx xx xxx.x [P/S]xx.x Playback Software / Real Time Monitor Instruction Manual 98 .x [AS/AH]xx.x xxx.x xxx.x xxx.x xxx. m/s deg(°) deg(°) deg(°) deg(°) kt kt deg(°) deg(°) min-1 min-1 deg(°) deg(°) kt kt kt deg(°) min-1 deg(°) deg(°) min-1 min-1 deg(°) deg(°) $xxRSA $xxRPM $xxRPM $xxTRD $xxVBW $xxRSA $xxRPM $xxRPM $xxHDT $xxHDT $xxVBW $xxRSA Sentence $xxMWV Ship (Docking) Speed Bow (The left and right in bow) SOG (Ground-reference) Stern (The left and right in stern) [P/S]xx.x xx xx xxx.x [AS/AH]xx.x xxx.x xx.x xxx.x xxx.x xxx.x xxx.x xx.x xxx.Chapter7 Appendix 7. Local Geodetic Datum Steer. Lon.g. Single.xxx’[N/S] xxx°xx. Mode Override Depth VDR (Numeric) Ship’s Position Date and Time Depth (Water / Tran.Chapter7 Appendix (2/4) Screen Block Section Data Indication Voyage1 Voyage2 (Graphic) Unit ------Sentence $xxETL Engine Telegraph Telegraph Position SUB Telegraph Ope.xxx’[N/S] xxx°xx.Location STOP ENGINE e.g. Starboard. Port wing. / Keel) UTC LMT Position Lat. Bridge. Wing e.g.g.xxx’[E/W] WGS84.g.WGS72 e. --- Voyage Info UTC DD/MM/YYYY hh:mm:ss --- $xxZDA LMT DD/MM/YYYY hh:mm:ss --- Position Lat. Propeller Cont.x DD/MM/YYYY DD/MM/YYYY GPS. DGPS xx°xx.x ------- $xxGNS $xxDTM $xxHTD m ----------- $xxDPT $xxZDA $xxGNS $xxDTM m/s deg(°) m/s deg(°) $xxMWV Playback Software / Real Time Monitor Instruction Manual 99 . xxx. F/A.x xx. DGPS xx°xx. Auto/Manual ON/OFF xxx. Lon.x xxx.WGS72 e.x xx. F/E e. Datum Wind speed and Direction Relative True Speed Direction Speed Direction GPS.xxx’[E/W] WGS84. Starboard wing e. S/B.g. x [P/S]xx.Chapter7 Appendix (3/4) Screen Block Section Data Indication VDR (Numeric) Depth Heading Speed Water and Ground True STW (Water-reference) SOG (Ground-reference) Bow (The left and right in bow) Stern (The left and right in stern) Rudder order and response Control/ Order Order/ Response Response Feedback Heading/Track control Steering mode Port Starboard Port Starboard Port Starboard Depth Offset from transducer Depth(Water/Tran.x [P/S]xx.x xxx.x xxx.x xxx./ Keel) xxx.x Manual Steering /Stand alone /Heading Control /Track Control /Rudder Control Override Heading-to-steer ON/OFF xxx --deg(°) m deg(°) kt kt kt kt deg(°) deg(°) deg(°) deg(°) deg(°) deg(°) --$xxHTD $xxRSA $xxHTD $xxHTC $xxHDT $xxVBW Unit --Sentence $xxDPT Playback Software / Real Time Monitor Instruction Manual 100 .x xxx.x [AS/AH]xx.x [AS/AH]xx.x xxx.x xxx.x xxx. x xx xxx.x xx xxx.x xx xxx.x xx xxx.x Unit min-1 deg(°) min-1 deg(°) min-1 deg(°) min-1 deg(°) min-1 deg(°) min-1 deg(°) min-1 deg(°) min-1 deg(°) $xxTRD $xxTRC $xxRPM Sentence $xxPRC Playback Software / Real Time Monitor Instruction Manual 101 .x xx xxx.Chapter7 Appendix (4/4) Screen Block Section Data Indication VDR (Numeric) Engine order and response Remote control order Starboard Port Revolution Pitch Revolution Pitch Propeller response Starboard Port Revolution Pitch Revolution Pitch Thruster control order and response Stern Control/Order Bow Revolution Pitch Revolution Pitch Response Bow Revolution Pitch Stern Revolution Pitch xx xxx.x xx xxx.x xx xxx. Chapter7 Appendix Blank Page Playback Software / Real Time Monitor Instruction Manual 102 . . co.contact: Not use the asbestos URL http://www.co.7ZPJD0357C 01ETM ISO 9001.For further information.jp e-mail : AMSTERDAM Branch Telephone : +31-20-658-0750 Facsimile : +31-20-658-0755 e-mail :
[email protected] Marine Service Department Telephone : +81-3-3492-1305 +81-3-3779-1420 Facsimile :
[email protected] SEATTLE Branch Telephone : +1-206-654-5644 Facsimile : +1-206-654-7030 e-mail : marineservice@jrcamerica. 2011 Edition 3 JRC Printed in Japan .com CODE No.jrc. ISO 14001 Certified JUL.