GPS Vehicle TrackerUSER MANUAL V5.0 CT03 1 Set ID for CT03 5.1 Hardware and Accessories 4.1 Basic SMS Commands 5.1.4 Set Time Interval for Sending GPRS Packet 5.1 Position Report 5.2 Light and Button Functionality 4.2 Set APN 5.2.2.2.5 Enable GPRS Tracking Function 6 Tracking on Map 7 Troubleshooting 8 SMS Command List 3 3 3 4 4 4 5 6 8 8 8 8 8 8 9 9 9 9 9 9 11 12 2 .1.4 Examples of Interfacing Application 5 SMS Command 5.2.3 Connecting and Installation 4.2 Set Interval for Automatic Timed Report 5.1.2 GPRS Setting by SMS 5.Contents 1 Product Overview 2 For Your Safety 3 CT03 Parameters 4 Getting Started 4.2.3 Set IP Address and Port 5.3 Stop Automatic Timed Report 5. Do not connect it to other incompatible devices. Water Resistance .CT03 is not water resistant. Analog Input: 2 10 bits resolution analog inputs 2 For Your Safety Read these simple guidelines.Use original parts. 5 outputs. Install it inside the vehicle or use waterproof bag if necessary. qualified batteries and peripheral equipments to avoid damage to CT03. read carefully its manual so as to carry out correct installation. Keep it dry. It can get accurate GPS fix even in remote places. CT03 has good sensitivity and stable performance.000+ waypoints Store in GPS blind area &forward when GPRS re-establish Built-in motion sensor for power saving SOS panic button Geo-fencing control Low battery alert Speeding alert Engine Cut Wiretapping (optional) Alert when CT03 enters/exits GPS blind area Alert when CT03 is turned on I/O: 5 digital inputs. 3 . Confidential Phone Number . Proper Connection . ---------Qualified Service . Read the full user manual for more information. With superior GPS and GPRS modules. Safe Driving . 3 negative and 2 positive triggering.When connecting with other device.For safety reason.Drivers should not operate this product while driving.1 Product Overview CT03 is a GPS/GSM/GPRS tracking device which is specially developed and designed for vehicle realtime tracking and security. Main Features: Tracking via SMS or GPRS (TCP/UDP) Current location report Tracking by time interval Position logging capacity up to 260. Not following them may be dangerous or illegal. do not tell other people the mobile phone number of your CT03 without taking precautions of security settings. Qualified Accessories .Only qualified personnel can install or repair CT03. 4 Getting Started This section will describe how to set up your CT03.1 second) Flashing (on for 0. 2 analog inputs. average 38 sec.1 Hardware Features CT03 includes: • CT03 Main Unit • GPS Antenna • GSM Antenna • Relay • Wires • USB Cable with converter • CD including .000 feet) max. 515 meters/second (1000 knots) max.9 seconds) Flashing (on for 1 second and off for 2 seconds) Green LED .1 second) Flashing (on for 0. average 42 sec. 1575.1 second and off for 2.3 CT03 Parameters Power Supply Backup Battery Dimension Installation Dimension Weight Operating temperature Humidity Frequency GPS Module GPS Sensitivity GPS Frequency C/A Code Channels Position Accuracy Velocity Accuracy Time Accuracy Default datum Reacquisition Hot start Warm start Cold start Altitude Limit Velocity Limit LED Flash Memory Interface +9V .1 sec.. 4. 2 LED lights to show GPS/GSM working status.1 second and off for 2.indicating GPS status On Flashing ( every 0. average 18.User Manual . average 1 sec.indicating GSM status On Flashing ( every 0..+35V / 1.023 MHz chip rate 20 channel all-in-view tracking 10 meters.42 MHz 1. 5 outputs. 3 negative and 2 positive triggering.9 seconds) Flashing (on for 1 second and off for 2 seconds) One or more inputs are active The unit is being Initialized CT03 has a GPS fix CT03 has no GPS fix One call is coming in/ one call is being made The unit is being Initialized CT03 is connected to the GSM network CT03 is not connected to the GSM network 4 .000 meters (60. 8MB 5 digital inputs...Other document or software if required 4.5A 850mAh 104mm x 62mm x 24mm 104mm x 83mm x 24mm 150g -20° to 55° C 5% to 95% Non-condensing GSM 900/1800/1900Mhz or GSM 850/900/1800/1900Mhz latest GPS SIRF-Star III chipset -158Db L1. 2D RMS 0.2 Light and Button Functionality Blue LED .1 m/s 1 us synchronized to GPS time WGS-84 0. Check that the SIM has not run out of credit (test the SIM in a phone to make sure it can send and receive SMS) . . The unused electrical wire should be properly insulated. It should be fixed to face the sky and should not be covered or shielded by any objects containing metal.GPS antenna is used to receive satellite signals in the sky. Connect the GSM Antenna to the unit. . Install SIM Card .If you require the function of sending an SMS location report to the authorized phone number when it makes a call to the CT03. Find a suitable place inside the car for installing the unit. .Put back the front cover and screw it up. A connector for microphone is set in the PCB. Before inserting SIM card. Ensure that your CT03 has a working SIM installed. If you need to link with an extra microphone for wiretapping purpose. cut off the power for the AVL unit. Check if all wirings have been connected correctly and then connect the unit to the motor power.Unscrew and remove the front cover of your CT03. Wiring connections must be firm and reliable and the joints should be wrapped with insulating tape tightly. please make sure the SIM installed supports displaying caller ID. Installation Guide: 5 . . Connect the GPS Antenna to the unit. such as the metallic windshield.3 Connecting and Installation Read this manual before using your CT03 and check if all parts are included in the packaging box.Insert the SIM card by sliding it into the card slot with the chip module facing to the connectors on PCB. contact us to add this optional function before we deliver the devices to you.SOS Button Press it to send SMS alert 4.Check that the SIM Lock code is turned off . Descriptions of PINs Pin 1 2 3 4 5 Color Red Black White Yellow Blue Function DC In. Refer to <GPS Tracker Parameter Editor> for configuration . 12V suggested.Input 4 / Input 5 Input 4 or Input 5 Ignition 3.PL-2303 Driver Installer . 4.for using the USB cable. Input voltage: 9V~35V.Input 4 / Input 5 6 .4 Examples of Interfacing Application For Input Ports 1. GND Digital Inputs Outputs 10 Bits Resolution Analog Inputs. You need to install the driver . Detecting Lock Status of Car’s Door or Trunk(Car Boot): Locked or Unlocked .Input 1 / Input 2 / Input 3 SOS Button White Black Input 1 or Input 2 or Input 3 2. Mini USB Port Connect the tracker with computer by USB cable for configuration and reading stored waypoints data. Input voltage: 0~6V. SOS Button . Ignition Detection . Input 2 / Input3 Input 2 / Input 3 Weight Sensor +12v/+24v For Output Ports 1. Engine Cut Car power supply Car battery +12v/+24v Relay Output 1 2. Connecting with Sensors (such as weight sensor) . Connecting with Car Alarm +12v/+24v Alarm Output 2 For Analog Input 7 .Power positive Status Input 4 or Input 5 +12v/+24v Lock Power negative Output 1 4. 37E.SMS Command List 5.3 Stop Automatic Timed Report Description: Automatic timed reports will stop once CT03 receives stop command.000 SMS received: Set Timer Ok/000 CT03 will stop automatic timed report For more detailed SMS commands please go to Chapter 8 .1 Basic SMS Commands 5. 5. If XXX=000 it will stop tracking Example: SMS sent: W000000.5 SMS Command CT03 will only accept commands from a user with the correct password.002.1 Position Report To know the location of your CT03.2 GPRS Settings by SMS Tracking via GPRS. Speed = 2. (c) Then after 20 second.1. Commands with wrong password are ignored.005 SMS received: Set Timer Ok/005 CT03 will then report its location by SMS every 5 minutes.000 SMS received: Latitude = 22 32 36. your mobile phone will receive a position SMS.6854Km/h. Command: W<password>. 2008-12-24.1.63N Longitude = 114 04 57. The default password is 000000. Command: W<password>. send an SMS or make a telephone call directly to CT03 and it will report its location by SMS.000 Example: SMS sent: W000000. 8 . Port and APN for CT03.002. 5. hang up the phone. (b) After listening to the ring for 10 . 5.002. you should set IP.XXX Notes: XXX is the interval in minute.2 Set Interval for Automatic Timed Report Description: Automatic timed reports will be sent to your mobile phone according to the time interval you set. Example: SMS sent: W000000. Command: W<password>.20 seconds.1.01:50 To get CT03’s position by another easier way: (a) Call CT03 using your mobile phone.<000> Notes: The default password is 000000.002. Ensure that your SIM card in CT03 supports GPRS connection prior to setting. Example: W000000.116.00003 CT03 will send GPRS packet every 30 seconds W000000.11.116. input APN only.5.010.12. Example: W000000. For more information regarding GPRS settings please refer to <GPRS Communication Protocol >. If you are using GpsGate Software.012.APN.011.com/) as the following picture shows: 9 .PORT Example: W000000.com/ Start the Google Earth (For more information about Google Earth please refer to http://earth.time interval(in unit of 10 seconds) Example: W000000.google. 5. 5.8000 CT03 will then reply an SMS (‘Set IP Ok /202.ID Note: Tracker ID must not over 14 digits.2.APN Password Note: If no APN name and password required.2.123456789 CT03 will then reply with an SMS (‘Set SIM Ok/123456789’) to confirm this setting.IP.1 Set ID for CT03 Command: W<password>.google. 5.014.8000’) to confirm this setting.CMNET CT03 will reply with an SMS (like ‘Set APN Ok/CMNET’) to confirm this setting.2. please contact us for writing GpsGate protocol before delivery.011.4 Set Time Interval for Sending GPRS Packet Command: W<password>.11.2.3 Set IP Address and Port Command: W<password>.2 Set APN Command: W<password>.014.202.010.014.00000 is “STOP GPRS” For more information regarding of bulk configuration by USB cable please refer to < GPS Tracker Parameter Editor>.12.APN Name.012. 6 Tracking on Map Download Google Earth from http://earth. Input the latitude and longitude that you receive from the tracker by SMS and click the search button. Example: When you receive: Latitude = 22 32 40.74E) Now you can find the location of your tracker: 10 .05N Longitude = 114 04 57.74E Type as the following picture shows: (Note: you should input the latitude and longitude as: 22 32 40. Google Earth will display the location for you.05N 114 04 57. Check in phone that the SIM can send SMS message. If you are in a different country your SIM account must have roaming enabled. clean the contacts. 7 Troubleshooting Problem: Unit will not turn on Possible Cause: Wiring was not connected properly Battery needs charging Problem: Unit will not respond to SMS Possible Cause: GSM antenna was not installed properly GSM Network is slow Unit is sleeping Wrong password in your SMS or wrong SMS format The SIM in CT03 has run out of credit No SIM card SIM card has expired SIM has PIN code set SIM is warped or damaged Roaming not enabled Resolution: Make CT03 connected to GSM network. Check in phone that the SIM can send SMS message. 11 . Replace SIM card if needed. Wait for the target to come out Recharge the unit and the GPS will start working. Or you can use local map software on PDA or car navigation device to input the coordinates.com for displaying the location. Some GSM networks slow down during peak time or when they have equipment problems. Wait for SMS. Resolution: Check and make sure wiring connection is in order.Or you can start the Internet Explorer and connect to http://maps. Remove PIN code by inserting SIM in you phone and deleting the code. If re-inserting does not help try another to see if it will work. Inspect SIM. Cancel sleeping mode Write correct password or SMS format Replace or top up the SIM card Insert working SIM card.google. Recharge battery Problem: SMS received starts with ‘Last…’ Possible Cause: Unit does not have clear view of the sky CT03 is in an inner place Battery is low Resolution: Move the antenna of the unit to a location where the sky is visible. 20] (unit: 10Km/h) For example. to send SMS. P=1. Close call to get location sms Presetting by SMS for GPRS tracking (Ensure that your SIM card supports GPRS connection prior to setting) Set ID for CT03 W******.000 W******. Set low power alert W******.5V send SMS alert (default ) =4 . Set over speed alert When CT03 speeds higher than the preset value.3V send SMS alert =2 .002. 200m =05.X T: Preset phone number. to turn off this function =[01. 50m =03. it will sent alert when it is over 80Km/h XX ( preset distance to original place ) =00. 12 . <3.XX =1.6V send SMS alert =5 . to turn off this function. F=1. 100m =04. Set Geo-fence alert W******. 2000m A=0.P.ID Tracker ID must not over 14 digits. <3. 30m =02. and the default password is 000000) Description Get current location Change user’s password Set interval for automatic timed report Set preset phone number for SOS button Command W******.7V send SMS alert XX (the preset value of speed) =00 .003. 500m =07.008. to turn off this function When CT03 voltage is lower than the preset value.Active call to get location sms A=1. As SOS button is linked to IN1.005. W000000.006.010. =01.###### W******.T Remarks Get current location of CT03 ****** is old password ###### is new password XXX is the interval in minute. Max 16 digits X (voltage preset value) =0 .F.8 SMS Command List (Remarks: ****** is user’s password.001.08. 300m =06.A000000### =08.XX W******. <3.005. it will send one low power alert to the SOS preset number. <3. If XXX=000 it will stop tracking F=0.4V send SMS alert =3 . 1000m Set calling tracker to get location sms W******. it will send an SMS to the SOS preset number. <3.XXX W******. it will send one Geo-fence SMS to the SOS preset number.004. close When the CT03 moves out of preset scope. Out2 =3.40.011. APN + APN name + password not over Set IP Address and Port Set Time Interval for Sending GPRS Packet W******.014. to close the output Output Control mode)------------(Safe W******. and Out5 respectively.Set APN W******.120. If A or B or C or D or E. to close this function.030. Out4. 16 digits F: ‘+’ or ‘-‘ TT: time zone difference (unit: hour) example.012.040. Out2. to open the output W******.ABCDE =1.P.IP.xxx. XXXXX=00001~65535. IP: xxx. Out4 =5. Port W******.APNName.APN Password If no APN name and password required. Out5 F =0.FTT =2. Out3 =4. time interval for sending GPRS packet and in unit of 10 seconds. to remain previous status T is the telephone number wiretapping and max. W000000.T W******.XXXXX 39 characters. For more information regarding GPRS settings please refer to <GPRS Communication Protocol> Output Control W******. to close the output =1. XXXXX=00000.xxx Port: [1.APN. Out1 =2. to open the output ABCDE represents Out1.F P =1. just insert APN only. =0. APN defaulted as ‘CMNET’.020.xxx.-08 for This function is achievable when the speed is below 10km/h and GPS is available. Out3.65534] XXXXX should be in five digitals and in unit of 10 seconds. Set phone number for wiretapping Set time zone difference 13 .