Corroseal rust converter is an elite, industrialstrength product for all your marine, household, automotive, and industrial rust problems. Paint, Prime, Convert Rust in One Step RESTORE METAL SURFACES Extend the life of your metal equipment by protecting it from rust and corrosion. Rust occurs naturally when the iron in steel oxidizes and returns to its original state, iron oxide. Through an innovative chemical conversion process, Corroseal Rust Converter converts rust (iron oxide) into a stable substance, magnetite. It also primes the surface with a high quality latex metal primer at the same time. Corroseal truly provides one step corrosion control. CORROSEAL FEATURES Water based rust converter with high quality latex metal primer Non-Flammable Non-Corrosive Easy to apply (brush, roll, or spray) Easy to cleanup with soap and water ECO-FRIENDLY ALTERNATIVE TO SANDBLASTING Corroseal is the best way to deal with rust because it is less expensive, less time consuming, and is much more environmentally friendly than sandblasting. Corroseal eliminates the need to sandblast rust by chemically converting rust from iron oxide to magnetite, a black and inert substance. Don't remove rust, convert rust! RUST CONVERTER - RUST PRIMER - METAL PRIMER Corroseal rust converter is your best rust treatment and corrosion control option because it meets all your metal surface preparation needs by converting the rust and priming the metal surface at the same time. MARINE Bridges Ships Decks & Deck Railing Boat Trailers Ferries Oar Locks Shipping Containers AUTOMOTIVE Automotive Restoration Vehicle Frames Recreational Equipment Utility Trailers Ramps Floorboards Quarter Panels HOUSEHOLD Garden Tools Lawnmowers Trailers Wrought iron furniture & railings Decorative Screens Pet Housing Mailboxes Fences INDUSTRIAL Storage & Fuel Tanks Structural Steel Manufacturing equipment Farm Equipment Implements Fencing and Gates Pipes Now Available! Product Data MSDS e.logical cleaner degreaser is a non-solvent, non-corrosive, and non-flammable cleaner and degreaser. Easily loosens oils, grease, and other soils for full suspension and removal from a variety of surfaces. Mild pH to use on most water safe surfaces. Can be diluted for all cleaning tasks. Concrete Floors Counter Tops Equipment Soft Metals Plastic / Vinyls Pressure Washing Map & Bucket Cleaning Engines Plexiglas Soak Tank Cleaning Hoods / Exhaust Fans Walls Glass / Fiberglass This product meets the Green Seal GS-37, 3rd addition standard for industrial and institutional cleaners when packed in bulk. M A T E R I A L S A F E T Y D A T A S H E E T PRODUCT NAME: CORROSEAL RUST CONVERTER HMIS CODES: H F R P PRODUCT CODE: CS100 2 0 0 H ============= SECTION I - MANUFACTURER IDENTIFICATION ============ MANUFACTURER'S NAME: RODDA PAINT COMPANY ADDRESS : 6123 N MARINE DRIVE PORTLAND, OR 97203 EMERGENCY PHONE : (800) 424-9300 DATE PRINTED : 01/25/08 INFORMATION PHONE : (503) 521-4300 NAME OF PREPARER : Rick Barnard ==== SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION ==== VAPOR PRESSURE WEIGHT REPORTABLE COMPONENTS CAS NUMBER MM HG @ TEMP PERCENT --------------------------------------------------------------------------- DIETHYLENE GLYCOL ETHYL ETHER ACETATE112-15-2 .05 68F 0 - 10 GALLIC ACID 149-91-7 0 - 10 # ETHYLENE GLYCOL 107-21-1 .05 20 C 0 - 10 OSHA TLV (vapor) ceiling 50 ppm * Indicates toxic material(s) subject to the reporting requirements of Section 313 of Title III and of 40 CFR 372. This product is believed not to contain materials listed as carcinogens by NTP, IARC, or OSHA. The above chemical(s) meet the criteria as defined under 29 CFR 1910 for toxic and hazardous substances. This product may contain small amounts of materials known to the State of California to cause cancer and reproductive harm. # Indicates materials listed in Section 112(b) of the Clean Air Act. ======== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ======== BOILING RANGE: 388 F - 417.2F SPECIFIC GRAVITY (H2O=1): 1.03 VAPOR DENSITY: Heavier than air. EVAPORATION RATE: Faster than Butyl Acetate. COATING V.O.C.: 0.69 lb/gl MATERIAL V.O.C.: 0.23 lb/gl SOLUBILITY IN WATER: Partial APPEARANCE AND ODOR: Milky white/beige liquid with mild odor. ========= SECTION IV - FIRE AND EXPLOSION HAZARD DATA ========= FLASH POINT: 211F METHOD USED: TCC FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: 0.9 UPPER: 19.4 EXTINGUISHING MEDIA: Alcohol foam, CO2 or dry chemical. SPECIAL FIREFIGHTING PROCEDURES: For fires involving this material, do not enter any enclosed or confined fire space without proper protective equipment. Self-contained breathing apparatus with a full facepiece operated in pressure-demand or other positive pressure mode to protect against the hazardous effects of normal products of combustion or oxygen deficiency. Water may not be effective for fighting fires. UNUSUAL FIRE AND EXPLOSION HAZARDS: Product may spatter if temperature of liquid exceeds the boiling point of water. If solids ignite, toxic and irritating gases can be emitted. Thermal decomposition of this product will produce carbon monoxide and carbon dioxide gases. ==================== SECTION V - REACTIBITY DATA ==================== STABILITY: | X | Stable | | Unstable CONDITIONS TO AVOID Freezing INCOMPATIBILITY (MATERIALS TO AVOID) Strong oxidizing agents, strong bases, and sulfide and sulfite compounds. HAZARDOUS DECOMPOSITION OR BYPRODUCTS Normal combustion forms carbon dioxide and water vapor; incomplete combustion can produce carbon monoxide. HAZARDOUS POLYMERIZATION: | | May occur | X | Will not occur =============== SECTION VI - HEALTH HAZARD DATA ================== INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE Use only with adequate ventilation. Do not breathe dust or spray mist. Ensure freah air entry during application and drying. For spray application, sanding, abrading, and dust cleanup, wear an appropriate properly fitted respirator (NIOSH/MSHA TC21C approved). Follow respirator manufacturer's directions for respirator use. If affected, remove to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration. Get medical attention. SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE This product contains acids which are corrosive to the skin and eyes. Symptoms of exposure include: redness and swelling of the eyes, burning, drying and cracking of the skin. SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE Prolonged exposure limit may result in the absorption of harmful amounts of material. INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE Swallowing this product may be harmful. If swallowed induce vomitting only if the person is conscious. HEALTH HAZARDS (ACUTE AND CHRONIC) Not considered a carcinogen by IARC, NTP or OSHA. Skin - Acute contact may cause irriation. Prolonged contact may cause burns. Chronic exposure may cause dermatitis. Eye - Acute contact may cause irritation and redness. Chronic exposure may cause conjunctivitis. Ingestion may cause headache, nausea, abdominal pains. HEALTH HAZARDS OF PREVIOUS COATINGS WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVIOD EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information hotline at 1-800- 424-LEAD or log on to www.epa.gov/lead. CARCINOGENICITY: NTP CARCINOGEN: No IARC MONOGRAPHS: No OSHA REGULATED: Yes This material is not listed as a human carcinogenic. MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE Inhalation may be an irritant to pre-existing respiratory conditions. EMERGENCY AND FIRST AID PROCEDURES SKIN- Wash exposed area with soap and water. EYES- Flush with large amounts of water. ======= SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ======= STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Persons not wearing protective equipment should be excluded from area of spill until clean-up had been completed. Stop spill at source, dike area of spill to prevent spreading, pump liquid to salvage tank. Remaining liquid may be taken up on sand, clay, earth, floor absorbent, or other absorbent material and shoveled into containers. Prevent run-off sewers, streams, or other bodies of water. WASTE DISPOSAL METHOD Destroy by liquid incineration. Material collected on absorbent material may be deposited in an approved landfill in accordance with local, state, and federal regulations. PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING Store in a cool, dry area. Keep away from heat, sparks, and open flame. Keep containers closed when not in use. Use only with adequate ventilation. OTHER PRECAUTIONS Containers of this material may be hazardous when emptied. Since emptied containers retain product residues (vapor, liquid, and/or solid), all hazard precautions given in this data sheet must be observed. READ AND OBSERVE ALL PRECAUTIONS ON LABEL! ================ SECTION VIII - CONTROL MEASURES ================ RESPIRATORY PROTECTION: If TLV of the product or any component is exceeded, a NIOSH/MESA jointly approved self-contained breathing apparatus with a full face piece operated in pressure demand or other positive pressure mode is advised; however, OSHA regulations also permit other NIOSH/MESA respirators under specified conditions. (See your safety equipment supplier). VENTILATION: Provide sufficient mechanical and/or local exhaust to maintain exposure below TLV(s). PROTECTIVE GLOVES: Wear resistant gloves such as: BUNA-N EYE PROTECTION: Chemical splash goggles in compliance with OSHA regulations are advised, unless full facepiece respirator is worn. OTHER PROTECTIVE CLOTHING OR EQUIPMENT: To prevent repeated or prolonged skin contact, wear impervious clothing and boots. WORK/HYGIENIC PRACTICES: Wash hands thoroughly after handling this product. ==================== SECTION IX - DISCLAIMER ===================== This information provided as a resource only. It should not be taken as a warranty or representation for which Rodda Paint Co. assumes legal responsibility. The information contained is believed to be accurate and compiled from sources believed to be reliable, it is the responsibility of the user to investigate and verify its validity. The user assumes all responsibility of using and handling the product in accordance with applicable federal, state, and local regulations. Corroseal ® Product Data PRODUCT IDENTIFICATION Corroseal ® Rust Converting Primer (CS100) PRODUCTS SKU# 82320 - 1 quart jug SKU# 82331 - 1 gallon jug SKU# 82335 - 5 gallon pail SKU# 82320 - 52 gallon drum PRODUCT DESCRIPTION Corroseal ® is a water based rust converter combined with a non pigmented high quality latex metal primer. The converter segments turn rust into a barrier layer of black non rusting magnetite. The primer acts as a bonding agent for oil-based intermediate and finish coatings of epoxy, enamel, acrylic, polyurethane and moisture-cured urethane, and with water based coatings not subject to tannin staining. Water based coatings may require an oil based stain blocker as an intermediate application. Corroseal ® is non flammable and non corrosive. DOT shipping classification 55 Universal Customs Code 3810.10 Basic Use Corroseal ® is recommended for use on rusted or partially rusted steel surfaces as a rust converter / paint primer, and as an etch primer on aged tight paint of any color, and as a sealer on non ferrous metals such as some aluminum, copper, and brass. Protects against future rusting Can be used on welds Eliminates need to mechanically blast to white metal in many instances Not recommended for outside hull underwater applications Packaging Corroseal ® is packaged in quarts, gallons, five gallon buckets and 52 gallon drums. Thinning DO NOT THIN Coverage The actual surface condition and thickness of rust will dictate the amount of Corroseal ® needed. For estimating purposes, 1 gallon of Corroseal ® covers approximately 200 square feet. Cautions Do not use in direct contact with food or potable water. Refer to the Corroseal MSDS and label for precautionary information. SURFACE PREPARATION Remove all salt, loose rust, mill scale, dirt, grease, oil, old paint and other deposits. Apply solvent cleaner according to manufacturer's directions and rinse. A residue free surface is essential before coating application begins. The surface should be a CLEAN, TIGHT RUST. Notes Do NOT use Acetone or dishwashing detergent to clean rusted steel surface. When black color appears, rust conversion has started. If gray areas appear apply more Corroseal® while surface is tacky. APPLICATION Brush, roll or spray undiluted Corroseal ® in a heavy white coat with no surface show through at 8-10 mils wet film thickness. When black color appears, rust conversion has started. Wait at least 24 hours before top coating. A second coat of Corroseal ® may be applied while first coat is still tacky. Apply all topcoats according to manufacturer’s specifications. Use oil based marine or industrial coatings for best weather protection. Application Conditions Keep from freezing, Apply at 45°F and rising and below 100°F(7°-37°C) and falling. Test over zinc based coatings as some galvanizing reject Corroseal ® chemistry. Do not apply onto zinc chromate or phosphates, lead, magnesium, copper powder, graphite, borate pigments. Chromate-treated (pickled) prefabricated steel building cold rolled perlins and gutters are to remain dry until top coated. Cold rolled steel can require abrading to anchor profile and degrease. Application Method Brush roll or spray undiluted Corroseal ® in a heavy white coat with no surface show through at 8-10 mils wet film thickness. Limitations Waterborne topcoats subject to tannin staining must be tested 48-60 hours before use. If tannin staining occurs, apply oil based stain blocker or apply oil based topcoat. Always prepare a test patch to ensure compatibility with substrate and follow-on coatings. DRY TIME Dry time to re-coat Wait at least 24 hours to top coat. TECHNICAL SERVICES Technical advice is available by calling Corroseal ® at 1-800-237-1573 or email inquiries to
[email protected]. Visitwww.corroseal.com for more information. Made in the USA by Rodda Paint Company, Portland Oregon. Corroseal ® Technical Data PRODUCT DESCRIPTION Corroseal ® is a water based rust converter combined with a non pigmented high quality latex metal primer. The converter segments turn rust into a barrier layer of black non rusting magnetite. Themetal primer acts as a bonding agent for oil-based intermediate and finish coatings of epoxy, enamel, acrylic, polyurethane and moisture-cured urethane, and with water based coatings not subject to tannin staining. Water based coatings may require an oil based stain blocker as an intermediate application. Corroseal ® is non flammable and non corrosive. BASIC USE Corroseal ® is recommended for use on rusted or partially rusted steel surfaces as a rust converter /metal primer, and as an etch primer on aged tight paint of any color, and as a sealer on non ferrous metals such as some aluminum, copper, and brass. Protects against future rusting Can be used on welds Eliminates need to mechanically blast to white metal in many instances Not recommended for outside hull underwater applications Availability SKU# 82320 - 1 quart jug SKU# 82331 - 1 gallon jug SKU# 82335 - 5 gallon pail SKU# 82320 - 52 gallon drum Appearance Milky, off-white to tan liquid Odor Very mild Thinning Do not thin Coverage 200 square feet per gallon @ 2.5 mil dry film thickness. 4.9 square meters per liter. Spreading Rate 8-10 mils wet film thickness, 200-250 microns, to create optimum dry film thickness of 2.5 mils to 3.5 mils DFT (65 to 90 microns) to cover anchor profile Cleanup Soap and water for equipment, hands, and clothes. Clean dried spatter with lacquer thinner. PHYSICAL PROPERTIES VOC (ATSM D 3960) 60 grams per Liter, 8 oz per gallon Non volatiles by volume 31% Non volatiles by weight 35% Weight per gallon 8.6 lbs, 3.91 Kg pH 3.0 Flash point (Closed Cup ASTM D 56) >200°F, > 93°C Viscosity (Brookfield model LVF #2 spindle, 60 rpm) 300 cps Heat Resistance Resists heat aging up to 270°F. Useful properties up to 350°F. UV Resistance (ASTM G-23 Ultraviolet Testing) 1000 hours - No Fading Cathodic Disbondment Corroseal Primer to rusted steel and top coated with - ASTM D4541 Wasser MoistureCure-CR-PW Average Pull Force at Failure 1128 psi Shelf life (ASTM D 1849) resists greater than 1 week at 140°F and up to or over one year between 38°F and 105°F, 3°C and 41°C. Avoid continuous direct sunlight. KEEP FROM FREEZING. Discard after freezing. Dry time (ASTM D 1640) at 3 mils wet film, 76 microns. Set to touch - 3 minutes Cotton free - 10 minutes Dry to touch - 30 minutes Hard dry - 40 minutes Through fingernail hard - 60 minutes Rejects rainwater at 77°F, 25°C - No wash off 240 minutes Recoat time at 77°F, 25°C Brush / Roller 15-30 minutes, Spray 10-20 minutes or between set to touch and dry to touch (tacky). Top coat time 24 hours minimum, up to 30 days TECHNICAL SERVICES Technical advice is available by calling Corroseal ® at 1-800-237-1573 or email inquiries to
[email protected]. Visitwww.corroseal.com for more information. Made in the USA by Rodda Paint Company, Portland Oregon.