www.smarterglass.com 978 997 4104 [email protected] Chunghwa Picture Tubes, Ltd. Technical Specification To Date : 2007.07.04 CPT TFT-LCD CLAA 201WA04 APPROVED BY JOY CHOU CHECKED BY Tristan PREPARED BY Product Planning Management General Division Prepared by : Design General Division CHUNGHWA PICTUER TUBES, LTD. No. 1, Huaying Rd., Sanho Tsun, Lungtan Shiang, Taoyuan, Taiwan, 325, R.O.C. TEL: +886-3-4805678 FAX: +886-3-4800589 Doc. No: CLAA201WA04- SPEC Issue Date: 2007/07/04 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. No： Version： Issue Date ： E 2007/07/04 Technical Specification Table Of Content NO 1 2 3 4 5 6 7 8 9 10 11 12 Table of Content OVERVIEW ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS INTERFACE PIN CONNECTION INTERFACE TIMING BLOCK DIAGRAM MECHANICAL SPECIFICATION OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS PACKING SPECIFICATION DESIGNATION OF LOT MARK HANDLING PRECAUTIONS FOR TFT-LCD MODULE ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. Note P.4 P.5 P.7 P.12 P.14 P.17 P.18 P.20 P.23 P.25 P.27 P.29 Page: 2/31 No： Version： Issue Date ： E 2007/07/04 Technical Specification 1.General specification are summarized in the following table: ITEM Display Area(mm) Number of Pixels Pixel Pitch(mm) Color Pixel Arrangement Display Mode Number of Colors Brightness(cd/m^2) Viewing Angle(H/V) Surface Treatment Power consumption(W) Module Size(mm) Module Weight(g) Backlight Unit ISO Datasheet No: T-3010004-008-F Datasheet Version. 7.1-inch diagonal) 1680 (H) × 1050(V) 0.OVERVIEW CLAA201WA04 is 20. Page: 3/31 .)(center. The module structure is fixed by iron frame. Interface of data and control signals is typ. Edge light CHUNGHWA PICTUER TUBES.9 (V) (20. TN 16.CHUNGHWA PICTUER TUBES. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc.) Anti-glare.6 (D) (Typ.258(H) × 0.) (w/o Inverter) 459. By applying 8 bit digital data (6bits+Hi-FRC).1”(51.7M(6bits+Hi-FRC) 300cd/m2 (Typ.5mA) 170/160 (Typ. drived by 5 voltages.) 2850(Typ) CCFL.without the inverter for the backlight.1” diagonal screen.4(H) ×16. LTD.16.: 01 SPECIFICATION 433.11cm) color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel.44 (H) × 270.7M-color images are displayed on the 20. LTD. 4 tubes(top × 2/bottom × 2) . 3H 34. control circuit and backlight(CCFL. LVDS driver ICs. 4 tubes).0(Typ.4(W) × 296.258(V) RGB vertical stripe NormallyWhite. 1680×1050. *3) If you use the product in a environment which over the definition of temperature and humidity too long to effect the result of eye-atching. may cause faulty operation or damage to the unit. ISO Datasheet No: T-3010004-008-F Datasheet Version. *6) If you operate the product in normal temperature range. If for special request testing. LTD. ITEM Power Supply Voltage For LCD SYMBOL VCC MIN. 2). 3). and then to measure TD with the same starting lamp voltage in dark room.0mA. (Ta≦40℃) *2) The maximum wet bulb temperature ≦39℃(Ta＞40℃) and without dewing. product life-time will decay rapidly or operate unusual. 6. 90%RHMax. 6) *1). Page: 4/31 .CHUNGHWA PICTUER TUBES. 3) sec *8) TD Delayed Discharge Time [Note] *1) The relative temperature and humidity range are as below sketch. VESDc：By using contact-mode to discharge the module. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 2.ABSOLUTE MAXIMUM RATINGS The following are maximun values which. . 7) FL VESDt VESDc Top Tstg 40 -200 -8000 0 -20 -- 80 200 8000 50 60 1 kHz V V ℃ ℃ -- Lamp Frequency Electrostatic Voltage Operation Temperature (Surrounding) Storage Temperature *5) *1).5 UNIT V Remark -- Lamp Voltage VL 770 970 Vrms -- Lamp Current ILO 3 8 mArms *4). lamp should operate at least 1min. LTD. 4 (BACKLIGHT) *5) The testing conditions are according to IEC 1000-4-2 specification： VESDt：By using contact-mode to discharge each pin of the connector. Doc. *4) Product life-time related to lamp current. 2). the lamp could be abnormal-starting. To place panel at room temp. if exceeded. and lamp current should follow typical lamp current specification. Humidity≦85%RH without condensation. 0 MAX.It is not to promise product life-time and lighting in normally situation. Relative Humidity ≦90% (Ta≦ 40℃) Wet Bulb Temperature ≦39℃(Ta≧40℃) *7) When lamp current over the definition of absolute maximun. If lamp current is under 3.: 01 CHUNGHWA PICTUER TUBES. *8) Delayed discharge time test condition: Starting lamp voltage = 1700 Vrms Before test TD. (25+/.then the minimun value of current is 2mA.2℃) below for 24hr. the center surface of panel should be under 60℃. pls operate the production follow statement at page 9 CN2. LTD.7) 20 5 -20 ISO Datasheet No: T-3010004-008-F Datasheet Version.50. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification Relative humidity(%RH) 90 Operating Range (40. Page: 5/31 .90) 80 Storage Range 60 (50. LTD.: 01 0 20 40 Temperature(°C) 50 60 CHUNGHWA PICTUER TUBES.CHUNGHWA PICTUER TUBES.27. Doc.4) 40 (60. LTD. DCLK.5 --90 Ta=25℃ TYP MAX UNIT REMARK 5.: 01 CHUNGHWA PICTUER TUBES.High electric potential threshold VTH voltage Low electric potential threshold VTL voltage *3) LCDInrush Current Inrush - - 3 A *4) Power consumption P - 4.0V 4.5V data LCD Power Supply Logic Signal 0.5V 4. Doc.CHUNGHWA PICTUER TUBES.TFT-LCD ITEM Power Supply Voltage for LCD Power Supply Current for LCD Permissive Ripple Voltage for Logic Differential Resistance SYMBOL VCC ICC VRP Zm MIN 4.5 W *2) [Note] *1)Power、data sequence 0. Page: 6/31 .0V 100 110 Ω VCM 1.25 1. ELECTRICAL CHARACTERISTICS (1).125 1. DENA ISO Datasheet No: T-3010004-008-F Datasheet Version.5 V *1) 900 1500 mA *2) -100 mVp-p VCC=5. LTD.375 V 250 350 450 mV - - 100 mV -100 - - mV The same motion input Voltage Differential input Voltage ｜VID｜ LVDS: IN+，IN.5V T7 VL Backlight Power Supply T3 T4 Data: RGB DATA.0 5.5 7.5V t1 t2 T5 T6 0.5ms＜t1＜10ms t4＞200ms 0＜t2＜50ms t7＞1sec 0＜t5＜50ms t3＞250ms 0.01ms＜t6＜10ms Vin=5.5V 0. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 3. 5 MHz 3).0 V，fH=65 kHz，fV=60 Hz，fCLK=73.LVDS Signal definition: VIN+：Positive differential DATA & CLK Input VIN-： Negative differential DATA ＆ CLK Input ISO Datasheet No: T-3010004-008-F Datasheet Version. No： Version： Issue Date ： E 2007/07/04 Technical Specification VCC-dip conditions: (1) When 3.CHUNGHWA PICTUER TUBES. LTD. LTD.6 V. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc.6V≦Vcc(min)<4.= Negative differential DATA & CLK Input 2). VIN+ = Positive differential DATA & CLK Input VIN. 1680 line mode VCC=5. Page: 7/31 .5V: td≦10 ms (2) When Vcc <3.: 01 CHUNGHWA PICTUER TUBES.VCC-dip conditions should also follow the VCC-turn-on conditions. Typical value is measured when displaying horizontal gray scale line pattern: 64 gray level. LTD.Irush Measurement Condition (2).Electrical specification ITEM SYMBOL MIN TYP MAX UNIT REMARK Lamp Voltage VL 720 800 880 Vrms IL=7.5 8.5 8.CHUNGHWA PICTUER TUBES. LTD.0 7.Backlight 1.0 mArms *1) Ta=25℃ WL － 28 － W FI 40 － 80 kHz IL=7. Doc.: 01 VS CHUNGHWA PICTUER TUBES. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 4).0 7. Page: 8/31 .0mA Ta=25℃ *1) *2) Ta=25℃ － － 1800 Vrms *5) Ta=0℃ － － 1550 Vrms *5) Ta=25℃ Lamp Power Consumption (for reference) Inverter Frequency Starting Lamp Voltage ISO Datasheet No: T-3010004-008-F Datasheet Version.5mA Ta=25℃ Lamp Current(Standard) IL 7.0 mArms *1) Ta=25℃ Lamp Current(Operation) ILO 3. 100.5 mA IL at 8 mA UNIT Min.: 01 CHUNGHWA PICTUER TUBES. designers have to try their best to fulfill the conditions under the inverter designing-stage as below: 1) Lamp Current measurement method (The current meter is inserted in cold line) CTL A CTH CTL A CTH INVERTER PowerSupply LCD CTL Module CTH CTL A A CTH ISO Datasheet No: T-3010004-008-F Datasheet Version.000 hr -- Min. 50. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 2. 30. the distribution of mercury inside the lamp tube will become unequally or will deplete the Ar gas in it. LTD.CHUNGHWA PICTUER TUBES.000 Min.000 -- time REMARK Continuous Operation*3) Continuous Operation*4) [Note] Inverter vender : Sumida.Lamp life time ITEM Lamp Life Time Turn-on and Turn-off Operation E 2007/07/04 Technical Specification IL at 3.0 mA IL at 7. model : IV50167/T If the waveform of light up-driving is asymmetric. Then it may cause the abnormal phenomenon of lighting-up. LTD.000 Min. Doc. Page: 9/31 . Therefore. 40. No： Version： Issue Date ： E 2007/07/04 Technical Specification a.5mA b. Repeat it for 100 thousand times d. TECHNICAL SPECIFICATION Title：CLAA201WA04 *2) Doc.03 e.and this may cause horizontal beat on the display. Starting Lamp Voltage: over130% of the initial value. Frequency is 10 sec. *3) Definition of the lamp life time： a. Lamp current is 7. The lamp hue variation must smaller than 0. Ta=25℃ *4) The condition of Turn-on and Turn-off operation is as below: a. Frequency in 50~60kHz can make characteristics of electric and optics better. please adjust lamp frequency. Frequency in 45~75kHz won’t damage the lifetime and reliability of lamp. d. b. c. LTD.CHUNGHWA PICTUER TUBES.10% except color coordinates. Page: 10/31 .Therefore. Luminance (L) under 50% of specification. *5) For keeping good lighting situation . *6) WL=IL x VL x 4。(IL=7. b. LTD.when design the inverter . Lamp frequency of inverter may produce interference with horizontal(or vertical) synchronous frequency. It should not have motion fail when starting lamp voltage is lower than 130%of the initial value.(off) c.(on)/10 sec.5mA，Ta=25℃) ISO Datasheet No: T-3010004-008-F Datasheet Version.it must be considered that the voltage large than starting lamp voltage. Frequency in this range can make the characteristics of electric and optics maintain in +/.: 01 CHUNGHWA PICTUER TUBES. and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. INTERFACE PIN CONNECTION (1) CN1 Outlet connector: FI-XB30SSRL-HF16 (JAE) (or equivalent) PIN NO.CHUNGHWA PICTUER TUBES. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. No： Version： Issue Date ： E 2007/07/04 Technical Specification 4. LTD.0 V) 29 VCC Power supply input voltage(5.0 V) 1) Keep the NC Pin and don’t connect it to GND or other signals.0 V) 30 VCC Power supply input voltage(5. REMARK FUNCTION 1 RXO0minus signal of odd channel 0(LVDS) 2 RXO0+ plus signal of odd channel 0(LVDS) 3 RXO1minus signal of odd channel 1(LVDS) 4 RXO1+ plus signal of odd channel 1(LVDS) 5 RXO2minus signal of odd channel 2(LVDS) 6 RXO2+ plus signal of odd channel 2(LVDS) 7 GND GND 8 RXOCminus signal of odd clock channel (LVDS) 9 RXOC+ plus signal of odd clock channel (LVDS) 10 RXO3minus signal of odd channel 3(LVDS) 11 RXO3+ plus signal of odd channel 3(LVDS) 12 RXE0minus signal of even channel 0(LVDS) 13 RXE0+ plus signal of even channel 0(LVDS) 14 GND GND 15 RXE1minus signal of even channel 1(LVDS) 16 RXE1+ plus signal of even channel 1(LVDS) 17 GND GND 18 RXE2minus signal of even channel 2(LVDS) 19 RXE2+ plus signal of even channel 2(LVDS) 20 RXECminus signal of even clock channel (LVDS) 21 RXEC+ plus signal of even clock channel (LVDS) 22 RXE3minus signal of even channel 3(LVDS) 23 RXE3+ plus signal of even channel 3(LVDS) 24 GND GND 25 NC NC 26 NC Test pin (Can’t connect to GND) 27 NC NC 28 VCC Power supply input voltage(5. Page: 11/31 . don’t let it be a vacant pin. 3. 5 (BACKLIGHT) CN2、CN3、CN4、CN5：BHSR-02VS-1 (JST) <Mating connector : SM02B-BHSS-1-TB (JST)> ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES. LTD. 2) GND Pin must connect to the ground. (2) CN2. 4. LTD. Doc. TECHNICAL SPECIFICATION Title：CLAA201WA04 No.: 01 CHUNGHWA PICTUER TUBES.CHUNGHWA PICTUER TUBES. LTD. Page: 12/31 . No： Version： Issue Date ： E 2007/07/04 Technical Specification Pin Symbol Description 1 HV High Voltage Output for CCFL Lamp 1 2 LV Low Voltage Output for CCFL Lamp 1 1 HV High Voltage Output for CCFL Lamp 2 2 LV Low Voltage Output for CCFL Lamp 2 1 HV High Voltage Output for CCFL Lamp 3 2 LV Low Voltage Output for CCFL Lamp 3 1 HV High Voltage Output for CCFL Lamp 4 2 LV Low Voltage Output for CCFL Lamp 4 CN2 CN3 CN4 CN5 ISO Datasheet No: T-3010004-008-F Datasheet Version. G.Timing Chart a.B) Invalid Data tHB Last Data 1 3 5 1677 1679 Invalid Data 2 4 6 1678 1680 Invalid Data tHA DENA ISO Datasheet No: T-3010004-008-F Datasheet Version. 61 12 1030 840 190 55 1060 1050 10 TYP.G.5 83 MHz 13.6 16. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 5. LTD.INTERFACE TIMING (1) Timing Characteristic ITEM SYMBOL Freq.: 01 CHUNGHWA PICTUER TUBES.4 ns 1135 1300 tCLK 840 840 tCLK 295 460 tCLK 60 75 Hz 1080 1300 tH 1050 1050 tH 30 250 tH [Note] *1) DENA (data enable) usually is positive *2) DCLK still inputs during blanking *3) LVDS transmitter IC: : NT71671-00033(NVT) *4) LVDS IC： Receiver Transmitter DS90C384MTD(NS DS90C383MTD(NS ) ) SN75LVDS82(TI) SN75LVDS83(TI) *5) DE mode only *6) It maybe cause flicker at 55Hz (2). Page: 13/31 .CHUNGHWA PICTUER TUBES.B) Invalid Data EVEN DATA (R. UNIT 73. LTD. fCLK DCLK Cycle tCLK Horizontal total time tH Horizontal Horizontal effective time tHA LCD Horizontal blank time tHB Timing Vertical frame Rate Fr DENA Vertical total time tV Vertical Vertical effective time tVA Vertical blank time tVB MIN. Doc. Horizontal Signal DCLK First Data ODD DATA (R. MAX. : 01 - ER[5] DATA for current CLK cycle CHUNGHWA PICTUER TUBES.CHUNGHWA PICTUER TUBES. EB[2] NEXT Page: 14/31 . Doc. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification b.LVDS Data For 6Bit+Hi-FRC 1CLK RXOC OB[6] RXO4 - RXO3 DE VS RXO2 OB[1] OB[0] OG[5] RXO1 OG[0] OR[5] OR[4] OB[7] PREVIOUS HS OG[7] OB[5] OG[4] OR[3] OG[6] OR[7] OR[6] OB[4] OB[3] OB[2] OG[3] OG[2] OG[1] OR[2] OR[1] OR[0] DATA for current CLK cycle NEXT 1CLK RXEC EB[7] RXE4 EB[6] EG[7] EG[6] ER[7] ER[6] EB[5] EB[4] EB[3] EG[5] EG[4] EG[3] EG[2] EG[1] ER[4] ER[3] ER[2] ER[1] ER[0] - RXE3 - - RXE2 EB[1] EB[0] EG[0] RXE1 PREVIOUS ISO Datasheet No: T-3010004-008-F Datasheet Version. Vertical Signal LINE DATA Invalid Data 1 1049 1050 3 2 tVB Invalid Data tVA DENA (3). LTD. LTD. 2) Data: 1-High.1) D(1680. 3)For odd & even data also. D(1679. . D(1. higher n means brighter level.Y) D(2.Y) .1050) CHUNGHWA PICTUER TUBES. + ..Y) . Page: 15/31 .1050) ISO Datasheet No: T-3010004-008-F Datasheet Version. D(X...CHUNGHWA PICTUER TUBES..2) ... LTD.1) .2) .. D(1679..1) D(2. + .1049) D(1679.Color Deta Distribution D(1.1050) D(2. + ..1) D(1679. .1050) D(1680. + . No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification Color Data Assignment COLOR INPUT DATA R7 MSB BLACK 0 RED(255) 1 GREEN(255) 0 BASIC BLUE(255) 0 COLOR CYAN 0 MAGENTA 1 YELLOW 1 WHITE 1 RED(0) 0 RED(1) 0 RED(2) 0 RED R DATA R6 R5 R4 R3 R2 R1 R0 LSB 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 G7 MSB 0 0 1 0 1 0 1 1 0 0 0 G DATA G6 G5 G4 G3 G2 G1 G0 LSB 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B7 MSB 0 0 0 1 1 1 0 1 0 0 0 B DATA B6 B5 B4 B3 B2 B1 B0 LSB 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(255) GREEN(0) GREEN(1) GREEN(2) 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 GREEN(255) BLUE(0) BLUE(1) BLUE(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 GREEN BLUE [Note] BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1) Definition of gray scale: Color (n): n indicates gray scale level.2) .1049) D(1680.. D(1. . LTD.. 0-Low. .2) D(2. D(X.. .1050) .. D(X. D(1679.Y) D(1680. D(X....2) D(1680.1049) . (4).: 01 .Y) .1) D(1. .. D(X.1049) D(2..1049) D(1.. Doc.. : 01 CHUNGHWA PICTUER TUBES.CHUNGHWA PICTUER TUBES. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc.BLOCK DIAGRAM CN2 CN3 CN4 CN5 ISO Datasheet No: T-3010004-008-F Datasheet Version. LTD. Page: 16/31 . No： Version： Issue Date ： E 2007/07/04 Technical Specification 6. LTD. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc.5mm unless noted) ISO Datasheet No: T-3010004-008-F Datasheet Version. LTD. [Unit:mm] Page: 17/31 .CHUNGHWA PICTUER TUBES. LTD.: 01 CHUNGHWA PICTUER TUBES.MECHANICAL SPECIFICATION (1) Front side (Tolerance is ± 0. No： Version： Issue Date ： E 2007/07/04 Technical Specification 7. 5mm unless noted) ISO Datasheet No: T-3010004-008-F Datasheet Version. LTD. LTD.: 01 Doc. TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification (2) Rear side (Tolerance is ±0. No： Version： Issue Date ： CHUNGHWA PICTUER TUBES.CHUNGHWA PICTUER TUBES. [Unit: mm] Page: 18/31 . 145 0.: 01 CHUNGHWA PICTUER TUBES. 9P Luminance (AVG): The white luminance is measured at measuring points 1 to 9. -75~75 -85~85 -- Deg. and all the other items are measured by BM-5A(TOPCON).343 0.328 0. Page: 19/31 . see Fig. -75~75 -85~85 -- Deg. -75~65 -85~75 -- Deg. TYP. LTD. LTD. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 8. Doc. see Fig.277 0.1 ISO Datasheet No: T-3010004-008-F Datasheet Version.358 0.359 0.111 -- 2.051 Gamut CG θ = ψ﹦0° 70 0. UNIT REMARK 700 1000 -- -- *1) Luminance (CEN) L θ = ψ﹦0° 250 300 -- cd/m2 *2) 9P Uniformity ΔL θ = ψ﹦0° 75 80 -- % *2) Response Time Tr+Tf θ = ψ﹦0° -- 5 8 ms *4) Cross talk CT θ = ψ﹦0° 0 -- 1 % *5) -75~75 -85~85 -- Deg.5mA × 4 Inverter: Sumida. 0.0V ITEM Contrast (CEN) SYMBOL CONDITION θ = ψ﹦0° CR MIN.313 0. And the measure time is 30 min after discharged.298 0.589 0.115 0.649 0. MAX.1 below.175 0. Measurement Condition: IL=7.081 72 Gamma γ VESA 2.CHUNGHWA PICTUER TUBES. Frequency=50kHz.299 0.4 Horizontal ψ Vertical θ Horizontal ψ Vertical θ White x y x y x y x y θ = ψ﹦0° 0.655 0.2 View angle Color Coordinates Red Green Blue CR≧10 CR≧5 *3) *2) % -- *6) [Note] Color coordinate and color gamut are measured by CS-1000.625 0.283 0.619 0. Definition of these measurement items is as follows: *1) Definition of Contrast Ratio CR=ON (White) Luminance/OFF (Black) Luminance *2) Definition of Luminance and Luminance uniformity Central luminance: The white luminance is measured at the center position “5” on the screen. All these items are measured under the dark room condition (no ambient light).0 2. OPTICAL CHARACTERISTICS Ta=25℃，VCC=5.247 0. model: IV50167/T－－ .307 0.685 0.329 0. LTD. 1） 1 2 3 1/10 H 5 4 525 6 H 8 7 9 （1680 . Page: 20/31 .Definition of Viewing Angle(θ. Doc.: 01 10 % Black tf CHUNGHWA PICTUER TUBES. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification below.CHUNGHWA PICTUER TUBES. 1050） 840 3). 9P Uniformity: Δ L = (LMIN /LMAX) ×100% W 1/10 W （1 . LTD.ψ): θ φ Upper Right Left Lower *4) Definition of Response Time: White 90 % 90 % Luminan 10 % tr ISO Datasheet No: T-3010004-008-F Datasheet Version. 240.32.. Doc. LTD.224. follow VESA standard sampling every 16 gray level(0.: 01 CHUNGHWA PICTUER TUBES.16.255) T % y =γx-k Gray level(LOG) ISO Datasheet No: T-3010004-008-F Datasheet Version. Page: 21/31 .….CHUNGHWA PICTUER TUBES. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 5) Definition of crosstalk: CT=∣YB-YA∣/YA X 100 (%) YA : The luminance of measured position at pattern A YB : The luminance of measured position at pattern B with Gray level 0 Pattern A Pattern B 6) Definition of Gamma ( γ). LTD. 2ms (NON-OPERATIO Number of shocks: one shock input in each direction of three N) mutually perpendicular axes for a total of six shock inputs Vibration level: 9.)；24 Hr CHUNGHWA PICTUER TUBES.0G) zero to peak Waveform: sinusoidal VIBRATION Frequency range: 5 to 500 Hz (NON-OPERATIO Frequency sweep rate: 0.: 01 CONDITION 260HPa (30000 ft. Contact mode. LTD.CHUNGHWA PICTUER TUBES. No： Version： Issue Date ： E 2007/07/04 Technical Specification 9. 240h BETWEEN -20℃(1hr)AND 60℃(1hr).z axis: 1 hour. test 25 times for each test point 3.48h (No condensation) 50℃. contact mode for each pin Module 1.RELIABILITY TEST CONDITIONS (1) Temperature and Humidity TEST ITEMS HIGH TEMPERATURE HIGH HUMIDITY OPERATION HIGH TEMPERATURE HIGH HUMIDITY STORAGE HIGH TEMPERATURE OPERATION HIGH TEMPERATURE STORAGE LOW TEMPERATURE OPERATION LOW TEMPERATURE STORAGE THERMAL SHOCK CONDITIONS 50℃. Page: 22/31 . Air mode. LTD.5 octave/min N) Duration: one sweep from 5 to 500Hz in each of three mutually perpendicular axis(each x. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. 90%RH. 150 pF，330 Ω，±15K V 2. 200 pF，0 Ω，±250 V 2. 240h 0℃.8m/s^2(1. 25 times for each test point (4) Low Presure test TEST ITEM Low Pressure test(storage) ISO Datasheet No: T-3010004-008-F Datasheet Version. total 3 hours) (3) ESD POSITION CONDITION( MDL turn off) Connector 1. 100 CYCLES (2) Shock & Vibration ITEMS CONDITIONS Shock level:100G SHOCK Waveform: half sinusoidal wave. 90%RH. 240h 60℃. 240h (No condensation) 60℃.y. 240h -20℃. Fail: No display image. obvious non-uniformity. No： Version： Issue Date ： E 2007/07/04 Technical Specification (5) Judgment standard The judgment of the above test should be made as follow: Pass: Normal display image with no obvious non-uniformity and no line defect. LTD. ISO Datasheet No: T-3010004-008-F Datasheet Version. Partial transformation of the module parts should be ignored. or line defects.CHUNGHWA PICTUER TUBES.: 01 CHUNGHWA PICTUER TUBES. Page: 23/31 . LTD. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. ) / 1 pallet z Box dimensions: 563(L)×292(W)×444(H) z Weight: approximately 18. LTD.3Kg (6 modules per box) (2)Packing Method Figures(a) and (b) are the packing method 20. PACKING SPECIFICATION (1)Packing z 6 LCD TV modules (max. LTD.) / 1 Box z 18 box (max.CHUNGHWA PICTUER TUBES.1” Module (5pcs) Figure(a) packing method ISO Datasheet No: T-3010004-008-F Datasheet Version. No： Version： Issue Date ： E 2007/07/04 Technical Specification 10.: 01 CHUNGHWA PICTUER TUBES. Page: 24/31 . TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. LTD. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. No： Version： Issue Date ： E 2007/07/04 Technical Specification Cover Protector: L1330 × 50 × 50mm Pallet: 1150(L) × 900(W) × 130(H) mm Top/Bottom Cap: L1150 × 1000 × 130mm Pallet stack: 1150(L) × 900(W) × 1465(H) mm Gross Weight: 345Kg(±2Kg) Fiqure(b) packing method ISO Datasheet No: T-3010004-008-F Datasheet Version. LTD.CHUNGHWA PICTUER TUBES.: 01 CHUNGHWA PICTUER TUBES. Page: 25/31 . I：Factory Code ISO Datasheet No: T-3010004-008-F Datasheet Version. No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification 11. Page: 26/31 . LTD. DESIGNATION OF LOT MARK (b) (c) (a) (a) 4_IN_1 LABEL: (Model Name: CLAA201WA04) B C D E F G H I A A：Year B：Week D、E、F、G、H：Serial No. Doc. LTD.CHUNGHWA PICTUER TUBES.: 01 CHUNGHWA PICTUER TUBES. 1~99. ISO Datasheet No: T-3010004-008-F Datasheet Version. LTD.: 01 CHUNGHWA PICTUER TUBES. Page: 27/31 . No： Version： Issue Date ： TECHNICAL SPECIFICATION Title：CLAA201WA04 E 2007/07/04 Technical Specification [Note] (1) Year Year 2000 2001 2002 2003 2004 2005 2006 2007 Mark 0 1 2 3 4 5 6 7 (2) Week Week 1 2 3 4 5 6 7 8 9 10 11 12 Mark 01 02 03 04 05 06 07 08 09 10 11 12 (3) Serial No.CHUNGHWA PICTUER TUBES. Doc.999 Mark 00001~99999 Factory Code Mark (4) Factory Code T1 T2 Factory Factory W R L Factory WJ1 Factory WJ2 Factory S U V (b) PANEL LABEL： XAT04KDE (c) B/L MAKER LABEL： ( F201WA04xxxxxxxxxxxxxxxxxxx) F201WA04xxxxxxxxxxxxxxxxxxx (2) Location of Lot Mark The label is attached to the backside of the LCD Module. LTD. Serial No. This is subject to change without prior notice. LTD. (2. (2. or not to interface the LCD module by the lamp cable. And do not soil LCD panel surface by touching with bare hands. (3) Please do not push or scratch LCD panel surface with any-thing hard.4) Design the inverter location and connector position carefully so as not to give stress to lamp cable. HANDLING PRECAUTIONS FOR TFT-LCD MODULE Please pay attention to the followings in handling. Page: 28/31 . TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. Approximately 1.CHUNGHWA PICTUER TUBES. (7) Please do not take a LCD module to pieces and reconstruct it. Approximately 1. (2. FPC cable and ferrite plate. ASSEMBLY PRECAUTION (1) Please use the mounting hole on the module side in installing and do not beading or wrenching LCD in assembling.) (4) Please do not press any parts on the rear side such as source TCP.TFT-LCD products. control circuit board and FPCs during handling LCD module. to be reconsidered when the additional parts are implemented for EMI countermeasure. bend or twist LCD module in handling. 1. (2. ( Polarizer film. surface of LCD panel is easy to be flawed. (6) Please wipe out drops of adhesives like saliva and water on LCD panel surface immediately. The stresses may cause non-uniformity even if there is no non-uniformity statically.5mm. such as. Resolving and ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES.0 mm of the clearance in the design is recommended taking into account the tolerance of LCD module thickness and mounting structure height on the housing. still sufficient clearance is required.2) Keep sufficient clearance between LCD module back surface and housing when the LCD module is mounted. especially. And please do not drop. such as inverter and speaker so as not to interface the LCD module. handle the LCD module with care not to damage them. (2) Please design display housing in accordance with the following guide lines. LTD. such as 0. They might damage to cause panel surface variation and color change. If pressing rear part is unavoidable. No： Version： Issue Date ： E 2007/07/04 Technical Specification 12. (5) Please wipe out LCD panel surface with absorbent cotton or soft cloth in case of it being soiled.3) When some parts. (2. gate TCP.1) Housing case must be destined carefully so as not to put stresses on LCD all sides and not to wrench module. are installed underneath the LCD module.0mm of the clearance in the design is recommended. This clearance is.5) Keep sufficient clearance between LCD module and the others parts. (3) Please consider that LCD backlight takes longer time to become stable of radiation characteristics in low temperature than in room temperature. ISO Datasheet No: T-3010004-008-F Datasheet Version. If then. STORAGE PRECAUTIONS (1) When you store LCDs for a long time. LTD. and so it is easy to be affected by electrostatics. A color change of the metal frames can happen during a long preservation of soiled LCD modules. (8) Please do not touch metal frames with bare hands and soiled gloves. time going on can make LCD work well. (6) Please obey the same caution descriptions as ones that need to pay attention to ordinary electronic parts. PRECAUTFONSWITHELECTROSTATICS (1) This LCD module use CMOS-IC on circuit board and TFT-LCD panel. Image might stick on LCD. (2) Please do not leave the LCDs in the environment of high humidity and high temperature such as 60℃ 90%RH. They are adjusted to the most suitable value.: 01 CHUNGHWA PICTUER TUBES. it might happen LCD does not satisfy the characteristics specification. (5) Please pay attention to displaying the same pattern for very long time. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc. it is recommended to keep the temperature between 0℃ ~40℃ without the exposure of sunlight and to keep the humidity less than 90%RH. 2.CHUNGHWA PICTUER TUBES. (2) Please remove protection film very slowly on the surface of LCD module to prevent from electrostatics occurrence. 3. LTD. Please be careful with electrostatics by the way of your body connecting to the ground and so on. (2) Please do not change variable resistance settings in LCD module. OPERATING PRECAUTIONS (1) Please be sure to turn off the power supply before connecting and disconnecting signal input cable. (9) Please pay attention to handling lead wire of backlight so that it is not tugged in connecting wit inverter. No： Version： Issue Date ： E 2007/07/04 Technical Specification reconstructing modules may cause them not to work well. If they are changed. 4. (4) A condensation might happen on the surface and inside of LCD module in case of sudden charge of ambient temperature. Page: 29/31 . 5. So please pay attention not to get them wet. which should later be burned. (3. LTD.3) Please handle packaging box with care not to give them sudden shock and vibrations. wash off throughly with soap and water. below -20℃. SAFETY PRECAUTIONS (1) When you waste LCDS. packaging box. and other materials becoming inferior. OTHERS (1) A strong incident light into LCD panel might cause display characteristics' changing inferior because of polarizer film. (2) Please pay attention to a panel side of LCD module not to contact with other materials in preserving it alone. 6. (They are not designed so. LTD. color filter. (3) For the. TECHNICAL SPECIFICATION Title：CLAA201WA04 Doc.And also please do not throw them up.) ISO Datasheet No: T-3010004-008-F Datasheet Version. Page: 30/31 .4) Packing box and inner case for LCDs are made of cardboard.: 01 CHUNGHWA PICTUER TUBES.1) Packaging box and inner case for LCD are designed to protect the LCDs from the damage or scratching during transportation.2) Please do not pile them up more than 5 boxes. please pay attention to the followings: (3. Please do not expose LCD module direct sunlight Land strong UV rays.CHUNGHWA PICTUER TUBES. Please do not open except picking LCDs up from the box. No： Version： Issue Date ： E 2007/07/04 Technical Specification (3) Please do not leave the LCDs in the environment of low temperature. (3.) And please do not turn over. (Such like keeping them in high humidity or wet place can occur getting them wet. (3. it is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol. (2) If any liquid leaks out of a damaged-glass cell and comes in contact with the hands.