CDX-GT31WGT310

CDX-GT31W/GT310/ GT360/GT360S SERVICE MANUAL US Model Canadian Model Ver. 1.4 2007. 04 CDX-GT31W/GT310 E Model CDX-GT360/GT360S Chinese Model CDX-GT360 (Photo: CDX-GT310) • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-GT11W/GT110/ CD Drive Mechanism Type MG-101TA-188//Q Optical Pick-up Name DAX-25A GT160/GT160S AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. SPECIFICATIONS CD player section Signal-to-noise ratio Frequency response Wow and flutter AM/MW Tuning range 530 – 1,710 kHz (GT31W/GT310) 531 – 1,602 kHz (at 9 kHz step) (GT360/GT360S) 530 – 1,710 kHz (at 10 kHz step) (GT360/GT360S) MW tuning interval 9 kHz/10 kHz switchable (GT360/GT360S) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV 120 dB 10 – 20,000 Hz Below measurable limit Tuner section FM Tuning range 87.5 – 107.9 MHz (GT31W/GT310) 87.5 – 108 MHz (at 50 kHz step) (GT360/GT360S) 87.5 – 107.9 MHz (at 200 kHz step) (GT360/GT360S) FM tuning interval 50 kHz/200 kHz switchable (GT360/GT360S) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz SW (GT360/GT360S) Tuning range SW1: 2,940 – 7,735 kHz SW2: 9,500 – 18,135 kHz (except for 10,140 – 11,575 kHz) Antenna (aerial) terminal External antenna (aerial) connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV – Continued on next page – FM/AM COMPACT DISC PLAYER CDX-GT31W/GT310 FM/MW/SW COMPACT DISC PLAYER CDX-GT360/GT360S 9-887-398-05 2007D04-1 © 2007. 04 Sony Corporation eVehicle Division Published by Sony Techno Create Corporation CDX-GT31W/GT310/GT360/GT360S Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. General Outputs TEST DISCS Please use the following test discs for the check on the CD section. Inputs Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories Audio outputs terminal (sub/rear switchable) Power antenna relay control terminal Power amplifier control terminal BUS control input terminal BUS audio input terminal Antenna input terminal AUX input jack (stereo mini jack) Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD) 12 V DC car battery (negative ground) Approx. 178 × 50 × 179 mm (7 1/8 × 2 × 7 1/8 in.) (w/h/d) Approx. 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) Approx. 1.2 kg (2 lb. 11 oz.) Card remote commander: RM-X151 Parts for installation and connections (1 set) YDES-18 (Part No. 3-702-101-01) PATD-012 (Part No. 4-225-203-01) CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pickup block. Design and specifications are subject to change without notice. optical pick-up SERVICE NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. semi-fixed resistor SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2 CDX-GT31W/GT310/GT360/GT360S This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the exterior. • CD playback You can play CD-DA (also containing CD TEXT*), CD-R/CDRW (MP3/WMA files also containing Multi Session . Type of discs Label on the disc E model CD-DA This label is located on the bottom of the chassis. MP3 WMA Chinese model * A CD TEXT disc is a CD-DA that includes information such as disc, artist and track name. SOLDER • UNLEADED Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CN350) and the SERVO board (CN2) with the extension cable (Part No. J-2502-076-1). MAIN BOARD CN350 Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. J-2502-076-1 SERVO BOARD CN2 3 CDX-GT31W/GT310/GT360/GT360S Ver. 1.3 NOTE FOR REPLACEMENT OF THE SERVO BOARD When repairing, the complete SERVO board (A-1177-201-A) should be replaced since any parts in the SERVO board cannot be repaired. NOTE FOR REPLACEMENT OF THE AUX JACK (J901) To replace the AUX jack requires alignment. 1. Insert the AUX jack into the KEY board. 2. Place the KEY board on the front panel. 3. Solder the three terminals of the jack. KEY board AUX jack TABLE OF CONTENTS 1. GENERAL Location of Controls ........................................................ 5 Connections ..................................................................... 6 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. Sub Panel (FL) Assy ........................................................ CD Mechanism Block ..................................................... Main Board ...................................................................... Servo Board ..................................................................... Chassis (T) Sub Assy ....................................................... Roller Arm Assy .............................................................. Chassis (OP) Assy ........................................................... 3. DIAGNOSIS FUNCTION ........................................ 13 4. DIAGRAMS 4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. Block Diagram –Main Section– ...................................... Block Diagram –Display Section– .................................. Printed Wiring Board –Main Section– ............................ Schematic Diagram –Main Section (1/3)– ...................... Schematic Diagram –Main Section (2/3)– ...................... Schematic Diagram –Main Section (3/3)– ...................... Printed Wiring Board –Key Section– .............................. Schematic Diagram –Key Section– ................................. 5. EXPLODED VIEWS 9 9 10 10 11 11 12 15 16 18 19 20 21 22 23 5-1. Main Section .................................................................... 28 5-2. Front Panel Section ......................................................... 29 5-3. CD Mechanism Section (MG-101TA-188//Q) ................ 30 6. front panel 4 ELECTRICAL PARTS LIST .................................. 31 CDX-GT31W/GT310/GT360/GT360S SECTION 1 This section is extracted GENERAL from instruction manual. • LOCATION OF CONTROLS • CDX-GT31W/GT310 Location of controls and basic operations Main unit 12 3 4 5 6 7 8 OFF PUSH SELECT EQ3 SOURCE SEEK AUX SEEK L Receptor for the card remote commander CAT MODE BTM DIM ALBM 1 DSPL 2 REP SHUF 3 4 9q; qa qs qdqfqg OFF SOURCE SEL MODE ws SCRL 1 2 3 4 5 6 qj C Volume control dial/select button 9 To adjust volume (rotate); select setup items (press and rotate). wd D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX/SAT*2). E Disc slot Insert the disc (label side up), playback starts. + ql CDX-GT310 CDX-GT31W B EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). – DSPL qj A OFF button To power off; stop the source. + qf SCRL Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit. w; wa qd ATT 6 qh Card remote commander RM-X151 1 4 qk PAUSE 5 VOL – K SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). M MODE button 8, 11 To select the radio band (FM/AM); select the SAT tuner band (mode)*2; select the unit*3. N DSPL (display)/DIM (dimmer) button 8 To change display items (press); change the display brightness (press and hold). O RESET button (located behind the front panel) 4 P Number buttons CD/MD*1: (1)/(2): ALBM –/+*4*5 To skip albums (press); skip albums continuously (press and hold). (3): REP 8 (4): SHUF 8 (6): PAUSE*6 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). Q SCRL (scroll) button 8 To scroll the display item. The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4). qk < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit. ql VOL (volume) +/– button To adjust volume. w; ATT (attenuate) button To attenuate the sound. To cancel, press again. wa SEL (select) button The same as the select button on the unit. ws M (+)/m (–) buttons To control CD, the same as (1)/(2) (ALBM –/+) on the unit. wd Number buttons To receive stored stations (press); store stations (press and hold). When an MD changer is connected. When the SAT tuner is connected. When a CD/MD changer is connected. When an MP3/WMA is played. If the changer is connected, the operation is different, see page 11. *6 When playing back on this unit. *1 *2 *3 *4 *5 Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 13. F Display window G AUX input jack 10 To connect a portable audio device. H Z (eject) button To eject the disc. I BTM/CAT*2 button 8 To start the BTM function (press and hold). J (front panel release) button 5 6 7 • CDX-GT360/GT360S Location of controls and basic operations Main unit 12 3 4 5 6 7 8 OFF PUSH SELECT EQ3 SOURCE AUX SEEK SEEK BTM L Receptor for the card remote commander MODE DIM DSPL ALBM 1 9q; qa qs qdqfqg qh Card remote commander RM-X151 1 4 ql OFF SOURCE ATT SEL MODE wa ws qd + wd – qf w; SCRL DSPL 1 2 3 4 5 6 + VOL – K SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). qk wf 2 REP SHUF 3 4 qj PAUSE 5 6 SCRL qk CDX-GT360S CDX-GT360 Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit. A OFF button To power off; stop the source. B EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). C Volume control dial/select button 9 To adjust volume (rotate); select setup items (press and rotate). D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX). E Disc slot Insert the disc (label side up), playback starts. F Display window G AUX input jack 10 To connect a portable audio device. M MODE button 8, 11 To select the radio band (FM/MW/SW); select the unit*2. N DSPL (display)/DIM (dimmer) button 8 To change display items (press); change the display brightness (press and hold). O RESET button (located behind the front panel) 4 P Frequency select switch (located on the bottom of the unit) See “Frequency select switch” in the supplied installation/connections manual. Q Number buttons CD/MD*1: (1)/(2): ALBM –/+*3*4 To skip albums (press); skip albums continuously (press and hold). (3): REP 8 (4): SHUF 8 (6): PAUSE*5 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4). ql < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit. w; VOL (volume) +/– button To adjust volume. wa ATT (attenuate) button To attenuate the sound. To cancel, press again. ws SEL (select) button The same as the select button on the unit. wd M (+)/m (–) buttons To control CD, the same as (1)/(2) (ALBM –/+) on the unit. wf Number buttons To receive stored stations (press); store stations (press and hold). When an MD changer is connected. When a CD/MD changer is connected. When an MP3/WMA is played. If the changer is connected, the operation is different, see page 11. *5 When playing back on this unit. *1 *2 *3 *4 Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 13. R SCRL (scroll) button 8 To scroll the display item. H Z (eject) button To eject the disc. I BTM button 8 To start the BTM function (press and hold). J 6 (front panel release) button 5 7 5 CDX-GT31W/GT310/GT360/GT360S • CONNECTIONS • CDX-GT31W/GT310 Source selector (not supplied) Sélecteur de source (non fourni) Supplied with XA-C40 Fourni avec le XA-C40 Supplied with the CD/MD changer Fourni avec le changeur de CD/MD XA-C40 *1 BUS AUDIO IN L R from car antenna (aerial) à partir de l’antenne du véhicule BUS AUDIO OUT IN REAR/SUB AUDIO OUT REAR*2 AMP REM 3 BUS CONTROL IN Fuse (10 A) Fusible (10 A) Blue/white striped Rayé bleu/blanc *1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *1 Cordon à broche RCA (non fourni) *2 AUDIO OUT peut être commuté sur SUB ou REAR. Pour obtenir plus de détails, reportez-vous au mode d’emploi fourni. 2 Max. supply current 0.3 A Courant max. fourni 0,3 A White Blanc Left Gauche Black Noir 1 White/black striped Rayé blanc/noir Gray Gris Right Droit Blue Bleu Green Vert Left Gauche ANT REM 2 Max. supply current 0.1 A Courant max. fourni 0,1 A Gray/black striped Rayé gris/noir Red Rouge 4 Green/black striped Rayé vert/noir Purple Violet Right Droit Yellow Jaune 5 Purple/black striped Rayé volet/noir Connection diagram Schéma de raccordement 1 To a metal surface of the car 1 À un point métallique de la voiture First connect the black ground (earth) lead, then connect the yellow and red power supply leads. 2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes • It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” 5 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna (aerial) in the rear/ side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’alimentation jaune et rouge. 2 Au câble de commande d’antenne électrique ou au câble d’alimentation de l’amplificateur d’antenne Remarques • Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas d’antenne électrique ni d’amplificateur d’antenne, ou avec une antenne télescopique manuelle. • Si votre voiture est Èquipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ». 3 Au niveau de AMP REMOTE IN de l’amplificateur de puissance en option Ce raccordement s’applique uniquement aux amplificateurs. Le branchement de tout autre système risque d’endommager l’appareil. 4 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoires Remarques • S’il n’y a pas de position accessoires, raccordez la borne d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule. • Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ». 5 À la borne +12 V qui est alimentée en permanence Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule. Remarques sur les câbles de commande et d’alimentation • Le câble de commande d’antenne électrique (bleu) fournit une alimentation de + 12 V CC lorsque vous mettez la radio sous tension. • Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou le câble d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre détaillant. • Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le câble d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt. Remarques sur le raccordement des haut-parleurs • Avant de raccorder les haut-parleurs, mettez l’appareil hors tension. • Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager. • Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes du hautparleur droit à celles du haut-parleur gauche. • Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur. • N’essayez pas de raccorder les haut-parleurs en parallèle. • Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil. • Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un câble négatif commun (–) pour les hautparleurs droit et gauche. • Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remarque sur le raccordement Si les haut-parleurs ne sont pas raccordés correctement, le message « FAILURE » s’affiche. Dans ce cas, assurez-vous que les haut-parleurs sont bien raccordés. 6 CDX-GT31W/GT310/GT360/GT360S • CDX-GT360/GT360S Source selector (not supplied) Selector de fuente (no suministrado) Supplied with XA-C40 Suministrado con el XA-C40 Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD XA-C40 * 1 BUS AUDIO IN *1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. L R BUS AUDIO OUT IN REAR/SUB from car antenna (aerial) desde la antena del automóvil AUDIO OUT REAR*2 AMP REM Blue/white striped Con rayas azules y blancas *1 Cable con terminales RCA (no suministrado) *2 AUDIO OUT (Salida de audio) puede cambiarse a SUB (Secundaria) o REAR (Posterior). Para obtener información, consulte el manual de instrucciones suministrado. BUS CONTROL IN Fuse (10 A) Fusible (10 A) 2 3 Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A Left Izquierdo *1 *2 White Blanco Black Negro 1 White/black striped Con rayas blancas y negras Right Derecho Blue Azul Grey Gris Left Izquierdo Right Derecho Max. supply current 0.1 A Corriente máx. de alimentación de 0,1 A Red Rojo Green Verde 4 Green/black striped Con rayas verdes y negras Purple Morado Yellow Amarillo Purple/black striped Con rayas moradas y negras Connection diagram 1 To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow and red power supply leads. 2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes • It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). • When your car has a built-in FM/MW/SW antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. • When your car has a built-in FM/MW/SW antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” 5 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/MW/SW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. ANT REM 2 Grey/black striped Con rayas grises y negras 5 Diagrama de conexión 1 A una superficie metálica del automóvil Conecte primero el cable de conexión a masa negro, y después los cables amarillo y rojo de fuente de alimentación. 2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de señal de la antena Notas • Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. • Si el automóvil incorpora una antena de FM/MW/SW en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 3 A AMP REMOTE IN de un amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. 4 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de encendido Notas • Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. • Si el automóvil incorpora una antena de FM/MW/SW en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 5 Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Notas sobre los cables de control y de fuente de alimentación • El cable de control de la antena motorizada (azul) suministrará cc de + 12 V cuando conecte la alimentación del sintonizador. • Si el automóvil dispone de una antena de FM/MW/SW incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su distribuidor. • Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Conexión para protección de la memoria Si conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notas sobre la conexión de los altavoces • Antes de conectar los altavoces, desconecte la alimentación de la unidad. • Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de potencia adecuada para evitar que se dañen. • No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. • No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz. • No intente conectar los altavoces en paralelo. • Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. • Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si la unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. • No conecte los cables de altavoz de la unidad entre sí. Nota sobre la conexión Si el altavoz no está conectado correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión del altavoz. 7 CDX-GT31W/GT310/GT360/GT360S Ver. 1.3 SECTION 2 DISASSEMBLY Note: This set can be disassemble according to the following sequence. SET 2-1. SUB PANEL (FL) ASSY (Page 9) 2-2. CD MECHANISM BLOCK (Page 9) 2-3. MAIN BOARD (Page 10) 2-4. SERVO BOARD (Page 10) 2-5. CHASSIS (T) SUB ASSY (Page 11) 2-6. ROLLER ARM ASSY (Page 11) 2-7. CHASSIS (OP) ASSY (Page 12) 1. CHUCKING ARM SUB ASSY (SUPPLEMENT-2 Page 1) 2. SLED MOTOR ASSY (SUPPLEMENT-2 Page 2) 3. OPTICAL PICK-UP SECTION (SUPPLEMENT-2 Page 3) 4. OPTICAL PICK-UP (SUPPLEMENT-2 Page 3) 8 CDX-GT31W/GT310/GT360/GT360S Note: Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL (FL) ASSY 3 two claws 2 two claws 1 two screws (+PTT 2.6 × 6) 4 sub panel (FL) assy 2-2. CD MECHANISM BLOCK 7 CD mechanism block 6 bracket (CD) 5 two screws (+PTT 2.6 × 4) 3 2 screw (+PTT 2.6 × 6) 4 CN350 1 screw (+PTT 2.6 × 6) 9 CDX-GT31W/GT310/GT360/GT360S 2-3. MAIN BOARD 2 two screws (+PTT 2.6 × 8) 4 two screws (+P 2.6 × 10) 5 two screws (+P 2.6 × 8) 1 three screws (+BTT) 6 two screws (+PTT 2.6 × 12) 7 screw (+PTT 2.6 × 10) 8 screw (+PTT 2.6 × 8) 9 heat sink 0 MAIN board 3 insulating sheet 2-4. SERVO BOARD WHT RED BLK WHT RED BLK RED ORG BLE YEL GRY 2 toothed lock screw (M 1.7 × 2.5) 3 toothed lock screw (M 1.7 × 2.5) SERVO board 5 SERVO board 1 Remove the eleven solders. 4 optical pick-up (16 core) (CN1) claw claw 10 CDX-GT31W/GT310/GT360/GT360S 2-5. CHASSIS (T) SUB ASSY 2 two precision screws (+P 1.7 × 2.2) 1 two precision screws (+P 1.7 × 2.2) 4 chassis (T) sub assy 3 claw 2-6. ROLLER ARM ASSY 5 roller arm assy 4 gear (RA1) 1 spring (RAL) 3 washer 2 spring (RAR) 11 CDX-GT31W/GT310/GT360/GT360S Ver. 1.3 2-7. CHASSIS (OP) ASSY 6 chassis (OP) assy 1 tension spring (KF) 5 7 coil spring (damper) (natural) 8 coil spring (damper) (green) 4 slider (R) 3 lever (D) 2 gear (LE1) 12 CDX-GT31W/GT310/GT360/GT360S SECTION 3 DIAGNOSIS FUNCTION Description of the Diagnostics function: 4. Contents of each display mode 4-1. Reset count display mode 1. Setting the Diag display mode With the power off, press the [4] button, [5] button, and [4] button on the set body or the remote control (for more than 2 seconds) in turn. 2. Canceling the Diag display mode During the Diag function mode, press the [OFF] button. 3. Initial display in the Diag display mode. Just when the Diag mode is entered, “reset count” is displayed. The display mode is switched by each rotation of SEEK +/M > or SEEK – /. m keys. XX Reset count (in hexadecimal format) Diag code 01: Reset count 4-2. Reset count by watchdog timer display mode 02 XX Reset count (in hexadecimal format) Reset count display 01 01 Diag code 02: Number of resets by watchdog timer XX 4-3. Number of connected units display mode Reset count by watchdog timer display 02 XX Number of connected units display 031 XXX 031 XXX Show the number of connected units for CD-C, MD-C and XM respectively from the rightmost (in hexadecimal format). Recency of information 1-3: 1 represents the latest. Diag code 03: Number of connected unit. Operating hours display 04 XXXX The display mode is switched by each rotation of [2/ALBM+] or [1/ALBM--] keys during the number of connected units display mode. CD error information display 051 No. of connected units history 1 (latest) display XX 031 OFFSET/FAILURE error display XXX No. of connected units history 2 display 061XXXXX 032 XXX No. of connected units history 3 display 033 XXX 4-4. Operating hours display mode 04 XXXX Operating hours (in hexadecimal format) Diag code 04: Operating hours 13 CDX-GT31W/GT310/GT360/GT360S 4-5. CD error information display mode 4-5-1. Error description 4-6. OFFSET/FAILURE error display mode 061XXXXX 051 XX Error information Error description Indication Description (in hexadecimal 1X SERVO ERROR format) 3X LOADING ERROR Recency of information 4X TRACK JUMP 1-3: 1 represents the latest. 5X TEXT ERROR Diag code FX MECHA ERROR 05: CD error information Operating hours Error description (0: OFFSET, 1: FAILURE) Recency of information 1-3: 1 represents the latest. Diag code 06: OFFSET/FAILURE The display mode is switched by each rotation of [2/ALBM+] or [1/ALBM--] keys during the OFFSET/FAILURE error display mode. 4-5-2. Disc type and operating hours 051XXXXX OFFSET/FAILURE error history 1 (latest) display Disc type Operating hours Disc type Recency of information 1-3: 1 represents the latest. Diag code 05: CD error information Indication 0 1 2 3 8 F Disc type MP3 WMA AAC ATRAC CD/DA UNKNOWN The display mode is switched by each rotation of [2/ALBM+] or [1/ALBM--] keys during the CD error information display mode. 061XXXXX OFFSET/FAILURE error history 2 display 062XXXXX OFFSET/FAILURE error history 3 display 063XXXXX CD error info history 1 (latest) Error description plus error details display 051 XX CD error info history 1 (latest) Disc type plus operating hours display 051XXXXX CD error info history 2 Error description plus error details display 052 XX CD error info history 2 Disc type plus operating hours display 052XXXXX CD error info history 3 Error description plus error details display 053 XX CD error info history 3 Disc type plus operating hours display 053XXXXX 14 CDX-GT31W/GT310/GT360/GT360S SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM — MAIN SECTION — J652 (1/2) ELECTRONIC VOLUME IC401 L BUS AUDIO IN R J652 (2/2) BUS-RCH CD L CD R CD-RCH CDON CDMON ZMUTE CD ON CDM ON Z MUTE CD MECHANISM UNIT (MG-101TA) CD-RCH 6 CD-LCH 5 CD-RCH AUX-RCH 9 AUX-LCH 7 AUX-RCH TU-RCH 4 TU-LCH 3 TU-RCH B/U CHECK B/U CHECK I2C BUS CONTROLLED POWER AMP/ MULTIPLE VOLTAGE REGULATOR IC300 12 IN FL OUT-RL 23 11 IN RL R-CH(FRONT) R-CH(REAR) MUTE Q440 SCL SDA MUTE CONTROL SWITCH Q491,492 DR+6V MECHA+6V BU+3.3V A+3.3V 2 10 D491 A ATT R-CH BATT 5 AMP-REM 6 ANT-REM D493 F901 16 VP 35 SERVO+3.3V D+3.3V SYSTEM CONTROL IC501 (1/2) AUX R-CH CDMON CDON ZMUTE AUX 92 CDMON 91 CDON 61 Z MUTE TU1 (TUNER UNIT) SDA SCL 2 SDA 4 SCL 16 BEEP 22 STB 25 DIAG VOLATT 9 ATT 100 BATT BATT SCL SDA I2C SCK 33 I2C SIO 34 RL+ RL– 4 FR+ 12 FR– 3 RR+ 11 RR– AMP REM 29 ANT REM 27 BU+3.3V AUDIO OUT REAR CN300 1 FL+ 9 FL– OUT FL+ 5 OUT FL– 3 OUT RL+ 9 OUT RL– 7 MUTE Q470 UNICLK UNI CLK J901 MUTE Q432 SCL 29 SDA 30 LINKOFF UNISO UNISI LINK OFF UNI SO UNI SI R R-CH MUTE 28 BUSON BUS ON R-CH OUT-FR 26 OUT-RR 24 A ATT A ATT L SUBOUT-L 21 SUBOUT-R 22 OUT-FL 25 SYSRST SYS RST BUS-RCH 2 BUS-LCH 1 BUS-RCH AUDIO+B BU+B SERVO3.3V MECHA6V PANEL+B 30 37 31 33 34 AUDIO+8.3V BU+5V SERVO+3.3V MECHA+6V PANEL+B BEEP 5 J1 (ANTENNA) L-CH 4 1 ANT R-CH 3 TUNER+5V REG Q3 E2PVDD 15 BU+3.3V TU-SCL 13 TU-SDA 14 DIAG 7 AUDIO+8.3V VCC 10 VDD+5V 11 AMPSTB 8 TU-RCH 7 ACCESSORY CHECK Q702 ACCIN 99 ACC AUDIO+8.3V BU+3.3V REG IC681 BU+5V 15 TESTIN 97 TEST BUS INTERFACE IC601 SCL SDA S-METER 6 TU MUTE 7 39 VSM 12 TUATT E2P SCL 16 E2P SDA 17 25 EEP CKO 24 EEP SIO 96 60 54 58 UNISO 59 12 11 10 8 9 BUSON UNISCK BUIN UNISI BUS IN CLK IN B/U-C DATA OUT DATA IN BATT 3 BATTERY CHECK Q605 SYSRST 88 13 RST 7 4 5 6 CLK 4 DATA I/O 6 BUS ON 1 D353 BUS ON SWITCH Q601 : CD PLAY (Page 16) RST 2 RESET : AUX CDX-GT31W/GT310/GT360/GT360S 15 15 UNISI B/U CHECK UNICLK BUSON : AM A UNISO DISPLAY SECTION SYSRST : FM LINK OFF SWITCH Q600 LINKOFF BATT BATT D609 • R-CH is omitted due to same as L-CH. • Signal Path TH400 D602 1 2 3 8 CNJ400 BUS CONTROL IN CDX-GT31W/GT310/GT360/GT360S 4-2. BLOCK DIAGRAM — DISPLAY SECTION — FL901 FLUORESCENT INDICATOR TUBE SYSTEM CONTROL IC501 (2/2) GRID1 20 41 KEYIN0 KEY MATRIX LSW901–910, S901–904,906,907 40 KEYIN1 D503 KEY ACKNOWLEDGE SWITCH Q664 RE901 PUSH SELECT (VOLUME) ROTARY ENCODER GRID2 19 FL SO 28 FL SCK 29 FL CS 27 14 DIO 12 CLK 10 CS GRID3 16 52 KEYACK 17 3G • 18 48 AD ON 6 2G • 42 31 RE-IN0 32 RE-IN1 1G 41 FL DRIVE Q883 FL VH+12V FL DRIVE Q882 FL DRIVE Q881 BU+3.3V ( S501 FREQUENCY SELECT RESET 15 10K ) PANEL+B 3 AREASEL2 VH 9 9K GT360/GT360S VDD(+3.3V) 5 62 NOSESW FL VH+12V VDD+3.3V REG IC972 PANEL+B PANEL+B REMOTE CONTROL SIGNAL RECEIVER IC971 64 SIRCS XOUT 80 XIN 79 MAIN SECTION OSCOUT 83 A RESET OSCIN 82 (Page 15) 1 F+ • 2 X502 32.768MHz FL+3V REG IC202 D204-206 D200-203 FL+7V REG IC201 FL+12V REG IC200 D207 BATT 44 F– • 45 X501 18.432MHz FL VH+12V FL+12V REG IC203 BU+3.3V FL ON 87 RESET IC602 77 RESET PANEL+B S103 RESET LED941–947 LSW901–910 GT360/ GT360S CDX-GT31W/GT310/GT360/GT360S 16 16 LED961 LED962, 963 LED862 LED863, GT31W/ 864 GT310 CDX-GT31W/GT310/GT360/GT360S • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Waveforms — MAIN Board — THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) 1 For schematic diagrams. For printed wiring boards. Note: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • C : panel designation. Note: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a : Through hole. • : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • • • • • • • • Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. A : B+ Line. B : B– Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : AM/MW/SW < > : CD PLAY ∗ : Impossible to measure Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY F : FM f : AM/MW/SW L : AUX Caution: Pattern face side: (Side B) Parts face side: (Side A) IC501 i; (XOUT) 0.8 Vp-p 32.768 kHz 0.2 V/DIV, 20 µsec/DIV 2 Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. IC501 is (OSC IN) 0.9 Vp-p C Q 18.432 MHz These are omitted B E 0.5 V/DIV, 0.1 µsec/DIV BE C These are omitted ECB These are omitted CDX-GT31W/GT310/GT360/GT360S 17 17 CDX-GT31W/GT310/GT360/GT360S 4-3. PRINTED WIRING BOARD — MAIN SECTION — 2 1 : Uses unleaded solder. 3 4 5 6 7 8 9 10 11 12 13 14 J652 L R CNJ400 (BUS CONTROL IN) -4 C325 C304 C301 IC300 C309 F901 R709 D113 JW3 C155 D106 D104 JW4 D110 D112 JW5 JW7 C154 (CHASSIS) C705 YEL JW105 IC601 JW106 JW104 C417 C412 C418 C419 JW110 D207 JW109 JW108 L405 C415 C402 C401 JW92 JW91 JC37 D353 C200 JW94 R600 IC602 3 2 4 1 L501 C201 IC203 JC23 R206 D206 D205 1 R210 D200 JW90 R205 D202 D201 5 C207 JW86 C204 D503 IC200 R201 1 JW88 JW83 JW82 R561 R200 C206 R208 JW111 JC2 R533 1 JW93 5 D203 C202 1 R202 IC201 R203 R204 5 D204 IC202 5 11 R207 S103 J CD MECHANISM UNIT (MG-101TA) R553 R211 JW84 R532 R517 JC16 R673 FMB3 JW81 JC3 R672 Q664 JC41 R154 D103 R152 JC25 D105 JC26 C152 R671 D111 R570 JW6 R153 L151 D109 C502 R502 D101 D108 C510 R351 R209 D502 JC24 C151 R155 R151 C514 R529 R567 C512 R565 R504 R505 C501 L406 R519 JC17 C205 R522 R521 C513 R503 C153 C702 C703 JW95 JC33 C315 C316 R674 C519 JC15 JW18 JW17 JW16 JW14 JW13 JW8 JW15 JC27 R610 D609 X501 JW22 R524 R520 R525 L5 JW20 JW107 R401 C507 IC501 JW19 H YEL JW64 JW65 JW63 JW68 JW67 C314 C313 R509 R510 R523 R512 Q601 L410 C509 JW12 JW11 JW9 R560 JW21 R612 Q600 CN350 R511 JC13 • Semiconductor Location GT31W/GT310 R557 R556 10K JW10 FMB4 JC40 G R552 R544 C504 JW79 JC38 JW28 R545 JW25 R537 JW80 R550 JW85 9K R538 JW29 JC20 R611 JC36 R402 JW78 R526 JW26 JW23 JW30 TH400 R615 R608 R601 JC35 GT31W/GT310 X502 R546 R551 C508 JW27 R507 R302 R540 JW113 C319 R534 GT360/GT360S S501 FREQUENCY SELECT R602 JC34 JW77 GT360/GT360S JC14 JW31 JC4 L4 R7 JW75 R616 D604 C601 JW89 JW41 C7 JW112 JW2 L401 R603 D602 JC19 L402 L409 R563 R604 Q605 R606 R607 R568 JW76 C318 JW32 JW100 R555 JW74 C363 JC12 C5 C8 JW1 JW96 C403 R566 D606 L407 L403 JW73 R301 D2 D153 R636 JC18 JW72 C317 JW37 R12 D603 JW71 D493 JW34 L300 JW103 D605 JW70 Q492 R531 D491 JW35 D304 JW87 JW44 Q491 JW43 JW33 D303 D302 JW98 JW69 JC1 R491 Q3 C2 D301 D607 L1 C6 R6 D311 D307 JW66 C682 C491 JW36 R13 JW62 JW61 JW60 JW58 D306 C683 L901 JC8 JW42 R10 D702 JW97 C364 C3 JW40 JW39 JC5 R9 I C681 C308 JW45 R3 C431 JC21 R707 JW99 JC32 C306 R451 R431 JC42 R485 C600 C704 R708 D310 IC681 JW46 C451 C15 R430 C471 R471 C461 JW38 R452 R5 JW24 JW57 R481 IC401 R460 JW102 C701 D703 R705 R440 R470 R2 F R420 R4 E C622 R461 C361 4 C997 Q702 D312 JW47 5 R706 L902 C365 C999 C366 C484 C362 TU1 D305 JC7 C486 D C623 C485 R355 JW56 R356 JW55 JC9 JC6 6 JW101 C312 C473 C472 R472 JW48 GT31W/GT310 JW114 1 JC22 D998 D309 Q470 C JW54 C463 C454 D308 C462 JW59 Q460 C320 JW53 C302 C303 R462 2 7 JW49 C434 JW52 JC10 3 8 C405 Q452 Q432 C305 C409 R357 C441 JC11 R358 R447 R448 R421 R442 C432 C421 C414 C307 C452 C998 JW51 C413 B JW50 C329 Q440 Q420 CN300 YEL C330 D901 C423 R450 R449 C203 C426 D999 C445 C443 JC30 -3 JC29 -2 JC31 R -1 C444 L C424 J1 (ANTENNA) A AUDIO OUT REAR BUS AUDIO IN CN370 S103 RESET X501 (Page 22) CDX-GT31W/GT310/GT360/GT360S 18 18 1-871-263- (11) Ref. No. D2 D101 D103 D104 D105 D106 D108 D109 D110 D111 D112 D113 D153 D200 D201 D202 D203 D204 D205 D206 D207 D301 D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D353 D491 D493 D502 D503 Location F-3 I-4 I-3 I-3 I-3 I-3 I-3 I-4 I-4 I-4 I-4 I-4 I-2 H-11 H-10 H-10 I-10 I-9 I-9 I-9 G-10 C-8 D-8 C-9 D-9 C-6 C-6 C-6 C-6 C-7 C-7 C-8 D-7 G-8 E-5 E-6 H-7 I-6 Ref. No. D602 D603 D604 D605 D606 D607 D609 D702 D703 D901 D998 D999 Location D-10 D-10 E-10 D-10 D-10 D-10 F-9 C-8 C-9 B-10 C-9 B-9 IC200 IC201 IC202 IC203 IC300 IC401 IC501 IC601 IC602 IC681 G-11 I-10 I-7 H-9 B-6 D-3 G-6 E-10 G-8 D-6 Q3 Q420 Q432 Q440 Q452 Q460 Q470 Q491 Q492 Q600 Q601 Q605 Q664 Q702 F-3 B-4 B-3 B-4 B-3 C-4 C-4 E-6 E-6 E-10 E-10 D-10 I-6 C-8 CDX-GT31W/GT310/GT360/GT360S 4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 24 for IC Block Diagrams. C303 C302 JC29 C325 C444 JC30 C301 C330 C424 L901 C308 C306 C304 JC31 C309 IC B/D C305 C307 C317 IC300 R302 C319 C318 C434 D999 R709 JC12 C320 C312 C314 C313 C316 C315 D303 D305 D306 D307 D308 D309 C997 D310 C998 D311 R705 D312 D301 C454 D302 R301 JC13 D304 CN300 D998 D702 D703 F901 D607 C704 C701 JC33 L902 JC32 C705 L300 R491 JC8 D491 JC9 IC602 R707 R706 C702 C703 (Page 20) IC681 Q491 Q702 Q492 D493 R708 JC1 R608 D602 Q600 R531 D603 Q601 TH400 C600 Q605 R610 C601 R612 CNJ400 JC22 JC21 R611 R616 R607 R602 R601 JC36 R606 D605 D901 C329 D604 D606 JC20 C683 R600 R603 R604 R615 IC B/D IC601 D609 (Page 21) CDX-GT31W/GT310/GT360/GT360S 19 19 C682 C681 C491 C622 C623 CDX-GT31W/GT310/GT360/GT360S 4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 24 for IC Block Diagrams. J652 J1 TU1 C445 C443 C426 C423 C463 C462 C473 C472 C999 C452 C432 C413 C414 C362 C361 Q470 Q460 Q420 Q440 Q452 Q432 R3 JC11 R357 JC10 R355 R472 R448 R462 R471 R461 C471 C461 R421 R447 R449 JC6 R442 C441 C421 C15 R358 R2 R356 R450 JC7 R451 R431 C451 C431 R4 R5 C365 C366 R9 JC5 C3 Q3 L1 C2 IC B/D R10 C7 C5 C6 IC401 C486 D2 C485 R13 R12 C8 L4 C484 R6 R420 R481 R440 R7 R460 R470 R452 JC42 (Page 19) C364 C363 R430 R485 L5 R558 IC B/D IC B/D IC B/D IC203 IC B/D IC200 D113 IC201 CN370 IC202 JC41 D207 R209 C207 R205 R204 D112 R207 R203 C201 D201 C203 D203 D204 D206 R206 R210 JC25 D111 JC26 D110 D109 R208 R211 C206 R202 R200 R201 D101 C200 D200 D202 D205 C202 D108 C205 C204 D103 D105 D104 D106 D153 C151 C152 C153 (Page 21) CDX-GT31W/GT310/GT360/GT360S 20 20 R151 R154 R153 C154 R155 L151 R152 C155 (Page 23) CDX-GT31W/GT310/GT360/GT360S • Refer to page 17 for Waveforms. 4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 26 for IC Pin Description of IC501. (Page 20) (Page 19) R568 R672 X502 C507 (MG-101TA) JC37 R532 R533 R529 R519 R561 R517 JC24 Q664 R570 JC2 D502 R674 C519 R553 C509 JC17 C508 JC19 JC16 CN350 X501 R565 C403 JC34 R555 C412 R509 JC35 L407 L501 C417 L409 L401 C405 R567 L402 R402 C510 R540 D503 C419 C502 L410 L403 C409 L405 C415 C514 R671 R401 R673 JC23 C418 R526 JC3 R505 R503 IC501 L406 R502 R636 R351 JC15 C513 R563 C401 R504 C512 C501 JC18 R522 C402 R521 R566 R520 R523 R524 D353 R534 R551 R552 R538 R507 R550 R537 R546 R545 JC40 JC38 R560 CDX-GT31W/GT310/GT360/GT360S 21 21 R556 C504 JC4 R512 R511 R510 R544 JC14 R557 JC27 S501 S103 R525 CDX-GT31W/GT310/GT360/GT360S 4-7. PRINTED WIRING BOARD — KEY SECTION — 2 8 9 10 11 12 13 LED941 S901 LED942 (CD INDICATOR) LED941, S901 R942 LED946 R861 LED945 S906 S903 GT31W/GT360 LSW901 R962 LED862 R862 SEEK– C LED961 GT360 /GT360S LSW902 7 LED942 R943 S904 LSW902 6 LED946,S903 SOURCE LSW901 M> SEEK+ LED862-864, LED961-963 (RING ILLUMINATION) R903 R904 5 R961 B 4 LED863 LED944, S904 EQ3 LED943 S902 R902 LED943, S902 OFF LED944 A 3 R941 1 : Uses unleaded solder. GT360 GT360 GT31W /GT360S /GT360S /GT310 LED963 LED962 R947 R906 R907 R908 LED947 R977 LED864 GT31W/GT310 C974 IC971 S907 R909 LED945, S906 BTM/CAT (GT31W/GT310) LSW903 BTM (GT360/GT360S) IC971 LED947, S907 MODE D LSW906 LSW910 R954 11 LSW907 1-871-320- (11) LSW905 LSW904 1/ALBM– LSW903 DSPL/DIM R959 R953 LSW909 LSW908 LSW905 LSW904 LSW906 3/REP 2/ALBM+ LSW908 5 LSW907 4/SHUF LSW909 6/PAUSE LSW910 SCRL (Page 18) MAIN BOARD CN370 45 44 42 R881 R882 FB902 D903 FB903 D908 R888 38 R889 D907 D905 Q883 D906 FB901 IC972 C976 R978 J901 AUX C975 C982 C981 R883 2 R988 3 R885 R971 R983 R981 1 R989 4 C977 R945 5 R884 D904 R886 R901 C904 FB904 FL901 FLUORESCENT INDICATOR TUBE Q881 Q882 R982 RE901 R951 R950 R949 R914 R887 GT31W /GT310 R948 CN901 R915 R863 R946 F R911 R864 R944 R905 R976 2 1 R975 R921 R922 R912 R910 D971 R952 E R913 A G RE901 PUSH SELECT (VOLUME) 11 1-871-320- (11) • Semiconductor Location CDX-GT31W/GT310/GT360/GT360S 22 22 Ref. No. D903 D904 D905 D906 D907 D908 D971 Location F-10 F-9 F-10 F-10 F-10 F-10 E-4 C-4 F-10 Ref. No. LED941 LED942 LED943 LED944 LED945 LED946 LED947 LED961 LED962 LED963 Location A-12 B-7 A-1 B-2 C-2 B-4 C-4 B-3 C-3 C-2 IC971 IC972 LED862 LED863 LED864 B-2 B-3 C-3 Q881 Q882 Q883 F-8 F-8 F-9 CDX-GT31W/GT310/GT360/GT360S 4-8. SCHEMATIC DIAGRAM — KEY SECTION — R981 R978 R943 R947 LED961 R951 C976 LSW910(1/2) LSW903(1/2) R945 R942 R954 R949 LED946 R941 IC972 C977 LSW906(1/2) LSW901(1/2) LED944 LED941 R944 R948 R863 R953 LED862 LSW907(1/2) LSW902(1/2) LED945 R962 R950 R982 R861 R959 R952 LED947 LED863 C975 LSW904(1/2) R946 LED942 R961 LED962 R862 R864 R975 R976 R977 IC971 LED943 LSW909(1/2) LSW905(1/2) (GT31W/GT310) LSW908(1/2) LED963 LED864 D971 (GT360/GT360S) C974 CN901 R887 C904 R971 C982 R983 R922 D908 D904 R889 R901 R902 R903 R886 Q883 FB904 R888 R921 R905 R904 R988 (Page 20) R883 RE901 (GT31W/GT310) R884 R882 Q881 R914 R915 R881 LSW910(2/2) R913 LSW909(2/2) LSW905(2/2) R912 LSW908(2/2) LSW904(2/2) R911 LSW907(2/2) R910 LSW906(2/2) R909 LSW903(2/2) LSW902(2/2) LSW901(2/2) R908 FL901 FB903 FB902 FB901 R907 S907 D907 D906 D905 (GT360/GT360S) R906 C981 Q882 S906 S904 S903 D903 S902 S901 R885 J901 CDX-GT31W/GT310/GT360/GT360S 23 23 R989 CDX-GT31W/GT310/GT360/GT360S • IC BLOCK DIAGRAMS IC300 TDA8588AJ/N2/R1 (MAIN Board (1/3)) IC601 BA8271F-E2 (MAIN Board (1/3)) TAB 1 2 SDA OUT-FL- 3 BUS ON 1 BUS ON SWITCH RST 2 RESET SWITCH BATT 3 BATTERY SWITCH 14 VCC I2C BUS 4 SCL FL OUT-FL+ 5 6 VP2 OUT-RL- 7 RL MUTE 10 SVR PROTECTION/ DIAGNOSTIC IN-RR 15 CLK 4 VREF 5 DATA 6 9 DATA IN GND 7 8 DATA OUT 12 IN-FL 14 IN-FR MUTE S-GND 13 RESET BUS ON CLK IN BU IN 8 PGND3 OUT-RL+ 9 IN-RL 11 13 12 11 10 16 BEEP VP OUT-RR+ 17 18 PGND2 RR OUT-RR- 19 20 VP1 OUT-FR+ 21 FR OUT-FR- 23 STANDBY/ MUTE 22 STB CHIP DETECT/ DIAGNOSTIC 24 PGND1 BATTERY DETECTION DIAG 25 TEMPERATURE PROTECTION IC200 IC201 IC202 IC203 ENABLE LOGIC 26 RST ANT-REM 27 SWITCH AMP-REM 29 SWITCH NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) CURRENT LIMIT 28 CRES REGULATOR 30 AUDIO8.3V SERVO5V 31 MECH6V 33 32 GND OVERVOLTAGE PROTECTION 34 PANEL+B VP 35 REFERENCE VOLTAGE B.UP+B 37 REGULATOR BANDGAP REFERENCE 36 CBU LOADDUMP PROTECTION THERMAL PROTECTION BACK-UP SWITCH CDX-GT31W/GT310/GT360/GT360S 24 24 1 2 3 4 5 VIN CONTROL VOUT VADJ GND CDX-GT31W/GT310/GT360/GT360S IC401 BD3442FS-E2 (MAIN Board (2/3)) BUS-RCH 1 VCC2 32 F2L 100k 31 GND BUS-LCH 2 100k TU-RCH 3 INPUT SELECTOR INPUT GAIN VOLUME1 /MUTE TREBLE /BASS /MIDDLE VOLUME2 I2C BUS LOGIC 100k TU-LCH 4 30 SDA 29 SCL 28 MUTE 100k CD-RCH 5 VCC 27 VCC 100k CD-LCH 6 FADER 26 OUT-FR 250k FADER 25 OUT-FL 250k FADER 24 OUT-RR FADER 23 OUT-RL 100k EFFECT AUX-RCH 7 AUX-GND 8 AUX-LCH 9 250k DS3-L 10 22 SUBOUT-R DS1-L 11 FADER DS2-L 12 LPF 21 SUBOUT-L EBIAS 13 FADER 20 ADJ DS2-R 14 DS1-R 15 DS3-R 16 19 SAOUT SPECTRUM ANALYZER 18 SADA 17 SACLK 25 CDX-GT31W/GT310/GT360/GT360S • IC PIN DESCRIPTION IC501 MB90F045PF-G-9015-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) Pin No. Pin Name I/O Pin Description 1 AREASEL0 I Destination setting pin 0 2 AREASEL1 I Destination setting pin 1 3 AREASEL2 I Destination setting pin 2 4 B-OUT SEL I Black-out with/without discrimination signal input 5 BEEP O Beep signal output 6 NCO O Not used. (Open) 7 DIAG I Status signal input from power amplifier 8 AMPSTB O Standby signal output to power amplifier 9 VOLATT O Electronic volume attenuate control signal output 10 NCO O Not used. (Open) 11 VSS — Ground pin 12 TUATT O Tuner mute control signal output 13 NSMASK O Noise mask signal output 14 ILLUMI SEL I Illumination voltage setting signal input 15 COL SEL I Two colors change setting signal input “H”: Black-out Not used in this set. (Open) 16 to 22 NCO O Not used. (Open) 23 VCC5 — Power supply pin (+3.3 V) 24 EEP SIO I/O EEPROM bus serial data signal input/output 25 EEP CKO O EEPROM bus serial clock signal output 26 RDS ON O 27 FL CS O RDS (Radio Data System) on signal output Tuner on: “L” Not used in this set. (Open) Fluorescent indicator tube chip select signal output 28 FL SO O Fluorescent indicator tube serial data signal output 29 FL SCK O Fluorescent indicator tube serial clock signal output 30 NCO O Not used. (Open) 31 RE IN0 I Rotary encoder signal input 0 32 RE IN1 I Rotary encoder signal input 1 33 I2C SCK O I2C bus serial clock signal output 34 I2C SIO I/O I2C bus serial data signal input/output 35 DAVDD — A/D converter power supply pin (+3.3 V) 36 AVRH — A/D converter external reference power supply pin (+3.3 V) 37 DAVSS — Ground pin 38 QUALITY I Noise detect signal input 39 VSM I S-meter voltage detect signal input 40 KEYIN1 I Key signal input 1 41 KEYIN0 I Key signal input 0 42 VSS — 43 RCIN0 I Rotary commander key signal input 44 to 47 NCO O Not used. (open) 48 AD ON O A/D converter power supply control signal output 49 MD0 I Operation mode setting pin (Connect to VDD.) 50 MD1 I Operation mode setting pin (Connect to VDD.) 51 MD2 I Operation mode setting pin (Connect to VSS.) 52 KEYACK I Key acknowledgment detect signal input 53 TUATTIN I Tuner mute zero cross detect signal input 54 BUIN I Back-up power supply detect signal input 55 NCO O Not used. (Open) 26 Not used in this set. Ground pin CDX-GT31W/GT310/GT360/GT360S Pin No. Pin Name I/O Pin Description RDS (Radio Data System) data block synchronized detect signal input 56 DAVN I 57 NCO O Not used. (Open) Not used in this set. 58 UNISI I SONY bus data signal input 59 UNISO O SONY bus data signal output Not used in this set. 60 UNI SCK O SONY bus clock signal output 61 Z MUTE I Mute signal input 62 NOSE SW I Front panel attachment detect signal input 63 FLASH W I Not used in this set. (Open) Not used in this set. Memory mode change signal input “L”: With panel, “H”: Without panel Normally “H”: Single chip mode, after reset “L”: flash write mode 64 SIRCS I Remote control signal input 65 to 70 NCO O Not used. (Open) 71 RC IN1 I Rotary commander shift key signal input 72 to 76 NCO O Not used. (Open) 77 RESET I CPU reset signal input 78 NCO O Not used. (Open) 79 XIN I Low speed operation clock signal input (32.768 kHz) 80 XOUT O Low speed operation clock signal output (32.768 kHz) 81 VSS1 — 82 OSCIN I 83 OSCOUT O High speed operation clock signal output (18.432 MHz) 84 VCC3 — Power supply pin (+3.3 V) 85 CYRIL SEL I Cyril correspondence discrimination signal input 86 DEMOSEL I DEMO select signal input 87 FL ON O Fluorescent indicator tube power on signal output 88 SYSRST O System reset signal output 89, 90 NCO O Not used. (Open) Not used in this set. Ground pin High speed operation clock signal input (18.432 MHz) “L”: No correspondence “H”: DEMO on, “L”: DEMO off 91 CDON I CD mechanism servo power supply control request signal input 92 CDMON I CD mechanism deck power supply control request signal input 93 to 95 NCO O Not used. (Open) 96 BUSON O Bus on signal output 97 TESTIN I Test mode detect signal input 98 TELATT I Telephone attenuate detect signal input 99 ACCIN I Accessory power supply detect signal input 100 ATT O Audio mute control signal output 27 CDX-GT31W/GT310/GT360/GT360S SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Abbreviation CND : Canadian model CH : Chinese model MX : Mexican model 5-1. • The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. -XX and -X mean standardized parts, so they may have some difference from the original one. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color Accessories are given in the last of this parts list. • • Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. MAIN SECTION not supplied A MG-101TA-188//Q #2 7 #1 #3 B A #3 #5 F901 4 #4 #3 #6 #3 not supplied 5 not supplied 3 6 #1 TU1 not supplied B 2 #1 not supplied #1 1 Ref. No. Part No. Description 1 2 3 4 5 X-2148-984-1 2-583-939-01 X-2148-837-1 2-583-940-01 A-1203-666-A PANEL (FL) ASSY, SUB SCREW (+B 2X4) LOCK ASSY SCREW (+BTT) MAIN BOARD, COMPLETE (GT31W) 5 5 5 6 7 A-1203-850-A A-1203-878-A A-1203-912-A 2-345-298-01 1-776-206-21 MAIN BOARD, COMPLETE (GT310) MAIN BOARD, COMPLETE (GT360) MAIN BOARD, COMPLETE (GT360S) PLATE (TU), GROUND CORD (WITH CONNECTOR) (POWER) 28 Remark Ref. No. Part No. Description Remark F901 TU1 TU1 #1 #2 1-532-877-11 A-3220-960-B A-3220-961-B 7-685-792-09 7-685-790-01 FUSE (BLADE TYPE) (AUTO FUSE) 10A TUNER UNIT (TUX-032) (GT360/GT360S) TUNER UNIT (TUX-032) (GT31W/GT310) SCREW +PTT 2.6X6 (S) SCREW +PTT 2.6X4 (S) #3 #4 #5 #6 7-685-793-09 7-685-795-09 7-685-134-19 7-621-284-40 SCREW +PTT 2.6X8 (S) SCREW +PTT 2.6X12 (S) SCREW +P 2.6X8 TYPE2 NON-SLIT SCREW +P 2.6X10 CDX-GT31W/GT310/GT360/GT360S Ver. 1.4 5-2. FRONT PANEL SECTION 58 57 RE901 not supplied 58 59 not supplied (KEY board) FL901 60 (GT31W/GT310 only) J901 56 not supplied not supplied not supplied 52 55 not supplied not supplied 54 51 53 Ref. No. Part No. Description Part No. Description 51 51 51 51 51 A-1203-668-A A-1203-870-A A-1203-880-A A-1203-914-A A-1211-715-A PANEL COMPLETE ASSY, FRONT (GT31W:US) PANEL COMPLETE ASSY, FRONT (GT310:US) PANEL COMPLETE ASSY, FRONT (GT360) PANEL COMPLETE ASSY, FRONT (GT360S) PANEL COMPLETE ASSY, FRONT (GT31W:CND) Remark Ref. No. 54 54 55 56 57 X-2149-078-1 X-2149-079-1 X-2149-075-1 2-693-726-01 2-684-608-01 PANEL (SV) ASSY, FRONT (GT360) PANEL (SV) ASSY, FRONT (GT360S) KNOB (VOL) (SV) ASSY SPRING (RELEASE) PANEL (FL), BACK Remark 51 52 52 53 54 A-1211-716-A X-2149-073-1 X-2149-074-1 3-251-320-01 X-2149-076-1 PANEL COMPLETE ASSY, FRONT (GT310:CND) BUTTON ASSY (S) (GT31W/GT310/GT360) BUTTON ASSY (S) (GT360S) EMBLEM (NO. 2.5), SONY PANEL (SV) ASSY, FRONT (GT31W) 58 59 60 FL901 J901 3-250-543-91 X-2148-896-1 X-2179-328-1 1-519-909-11 1-820-624-11 SCREW (+B P-TITE M2) CASE ASSY (for FRONT PANEL) (EXCEPT US) PC BOARD (SV) ASSY, KEY (GT31W/GT310) INDICATOR TUBE, FLUORESCENT JACK (SMALL TYPE) (VERTICAL) (AUX) 54 X-2149-077-1 PANEL (SV) ASSY, FRONT (GT310) RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME) 29 CDX-GT31W/GT310/GT360/GT360S Ver. 1.3 5-3. CD MECHANISM SECTION (MG-101TA-188//Q) NOTE: Refer to SUPPLEMENT-2 for disassembly of OPTICAL PICK-UP. 101 102 not supplied not supplied 103 #7 #7 105 not supplied not supplied not supplied not supplied not supplied 104 not supplied not supplied not supplied not supplied 107 106 106 Ref. No. Part No. Description 101 102 0 103 104 A-1177-168-A A-1177-169-A X-2149-672-1 2-626-869-01 MECHANICAL BLOCK ASSY DAXEV//Q SERVICE ASSY, OP (DAX-25A) SCREW (M2X3), SERRATION 30 Remark Ref. No. 105 106 107 #7 Part No. Description 3-348-998-31 3-352-758-31 A-1177-201-A 7-627-000-08 SCREW (M1.4X2.5), TAPPING, PAN SCREW (M1.7X2.5), TOOTHED LOCK SERVO BOARD, COMPLETE SCREW, PRECISION +P 1.7X2.2 TYPE3 Remark CDX-GT31W/GT310/GT360/GT360S Ver. 1.4 SECTION 6 KEY ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Abbreviation CND : Canadian model CH : Chinese model MX : Mexican model Ref. No. Part No. • • • • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. CAPACITORS uF : µF COILS uH : µH Description Remark < CAPACITOR > 1-165-176-11 1-107-826-11 1-107-826-11 1-107-826-11 1-125-891-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP C981 C982 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board. X-2179-328-1 PC BOARD (SV) ASSY, KEY (GT31W/GT310) not supplied KEY BOARD, COMPLETE (GT360/GT360S) ******************** C904 C974 C975 C976 C977 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 0.047uF 0.1uF 0.1uF 0.1uF 0.47uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 10V 0.1uF 0.1uF 10% 10% 16V 16V Ref. No. Part No. Description Remark LED863 6-500-510-01 LED CL-195PG-CD-T (RING ILLUMINATION) (GT31W/GT310) LED864 6-500-510-01 LED CL-195PG-CD-T (RING ILLUMINATION) (GT31W/GT310) LED941 6-500-450-01 LED CL-195SR-CD-T (Z) (GT360/GT360S) LED941 6-500-510-01 LED CL-195PG-CD-T (Z) (GT31W/GT310) LED942 6-500-450-01 LED CL-195SR-CD-T (CD INDICATOR) (GT360/GT360S) LED942 6-500-510-01 LED CL-195PG-CD-T (CD INDICATOR) (GT31W/GT310) LED943 6-500-450-01 LED CL-195SR-CD-T (OFF) (GT360/GT360S) LED943 6-500-510-01 LED CL-195PG-CD-T (OFF) (GT31W/GT310) LED944 6-500-450-01 LED CL-195SR-CD-T (EQ3) (GT360/GT360S) LED944 6-500-510-01 LED CL-195PG-CD-T (EQ3) (GT31W/GT310) < CONNECTOR > CN901 1-820-619-11 PLUG, CONNECTOR 20P < DIODE > D903 D904 D905 D906 D907 6-501-180-01 6-501-180-01 6-501-170-01 6-501-170-01 6-501-170-01 DIODE DIODE DIODE DIODE DIODE UDZW-TE17-18B UDZW-TE17-18B UDZW-TE17-6.8B UDZW-TE17-6.8B UDZW-TE17-6.8B D908 D971 6-501-170-01 DIODE UDZW-TE17-6.8B 6-501-167-01 DIODE UDZW-TE17-5.1B < FERRITE BEAD > FB901 FB902 FB903 FB904 1-216-864-11 1-216-864-11 1-216-295-11 1-469-876-11 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 INDUCTOR, FERRITE BEAD LED945 6-500-450-01 LED CL-195SR-CD-T (BTM) (GT360/GT360S) LED945 6-500-510-01 LED CL-195PG-CD-T (BTM/CAT) (GT31W/GT310) LED946 6-500-450-01 LED CL-195SR-CD-T (SOURCE) (GT360/GT360S) LED946 6-500-510-01 LED CL-195PG-CD-T (SOURCE) (GT31W/GT310) LED947 6-500-450-01 LED CL-195SR-CD-T (MODE) (GT360/GT360S) LED947 6-500-510-01 LED CL-195PG-CD-T (MODE) (GT31W/GT310) LED961 6-500-450-01 LED CL-195SR-CD-T (RING ILLUMINATION) (GT360/GT360S) LED961 6-500-510-01 LED CL-195PG-CD-T (RING ILLUMINATION) (GT31W/GT310) LED962 6-500-450-01 LED CL-195SR-CD-T (RING ILLUMINATION) (GT360/GT360S) LED963 6-500-450-01 LED CL-195SR-CD-T (RING ILLUMINATION) (GT360/GT360S) < SWITCH > < FLUORESCENT INDICATOR TUBE > FL901 1-519-909-11 INDICATOR TUBE, FLUORESCENT < IC > IC971 IC972 6-600-163-01 IC RS-770 (IR) 6-706-715-01 IC NJM2867F33(TE2) < JACK > J901 LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED) (M > SEEK+) (GT360/GT360S) LSW901 1-786-806-12 SWITCH, TACTILE (WITH LED) (M > SEEK+) (GT31W/GT310) LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (. m SEEK–) (GT360/GT360S) LSW902 1-786-806-12 SWITCH, TACTILE (WITH LED) (. m SEEK–) (GT31W/GT310) LSW903 1-786-805-12 SWITCH, TACTILE (WITH LED) (DSPL/DIM) (GT360/GT360S) 1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX) < DIODE > LED862 6-500-510-01 LED CL-195PG-CD-T (RING ILLUMINATION) (GT31W/GT310) LSW903 1-786-806-12 SWITCH, TACTILE (WITH LED) (DSPL/DIM) (GT31W/GT310) LSW904 1-786-805-12 SWITCH, TACTILE (WITH LED) (1/ALBM –) (GT360/GT360S) LSW904 1-786-806-12 SWITCH, TACTILE (WITH LED) (1/ALBM –) (GT31W/GT310) 31 CDX-GT31W/GT310/GT360/GT360S KEY Ref. No. Part No. Description Remark LSW905 1-786-805-12 SWITCH, TACTILE (WITH LED) (2/ALBM +) (GT360/GT360S) LSW905 1-786-806-12 SWITCH, TACTILE (WITH LED) (2/ALBM +) (GT31W/GT310) LSW906 1-786-805-12 SWITCH, TACTILE (WITH LED) (3/REP) (GT360/GT360S) LSW906 1-786-806-12 SWITCH, TACTILE (WITH LED) (3/REP) (GT31W/GT310) LSW907 1-786-805-12 SWITCH, TACTILE (WITH LED) (4/SHUF) (GT360/GT360S) LSW907 1-786-806-12 SWITCH, TACTILE (WITH LED) (4/SHUF) (GT31W/GT310) LSW908 1-786-805-12 SWITCH, TACTILE (WITH LED) (5) (GT360/GT360S) LSW908 1-786-806-12 SWITCH, TACTILE (WITH LED) (5) (GT31W/GT310) LSW909 1-786-805-12 SWITCH, TACTILE (WITH LED) (6/PAUSE) (GT360/GT360S) LSW909 1-786-806-12 SWITCH, TACTILE (WITH LED) (6/PAUSE) (GT31W/GT310) LSW910 1-786-805-12 SWITCH, TACTILE (WITH LED) (SCRL) (GT360/GT360S) LSW910 1-786-806-12 SWITCH, TACTILE (WITH LED) (SCRL) (GT31W/GT310) Ref. No. Part No. Description R913 R914 R915 R921 R922 1-216-827-11 1-216-828-11 1-216-830-11 1-216-295-11 1-216-295-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP R941 Remark 3.3K 3.9K 5.6K 0 0 5% 5% 5% 1/10W 1/10W 1/10W 1-216-810-11 METAL CHIP 120 R941 1-216-813-11 METAL CHIP 220 R942 1-216-810-11 METAL CHIP 120 R942 1-216-813-11 METAL CHIP 220 R943 1-216-811-11 METAL CHIP 150 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) R943 1-216-812-11 METAL CHIP 180 R944 1-216-810-11 METAL CHIP 120 R944 1-216-811-11 METAL CHIP 150 R945 1-216-811-11 METAL CHIP 150 R945 1-216-812-11 METAL CHIP 180 R946 1-216-810-11 METAL CHIP 120 R946 1-216-811-11 METAL CHIP 150 R947 1-216-811-11 METAL CHIP 150 R947 1-216-812-11 METAL CHIP 180 R948 1-216-810-11 METAL CHIP 120 R948 1-216-811-11 METAL CHIP 150 R949 1-216-807-11 METAL CHIP 68 R949 1-216-809-11 METAL CHIP 100 R950 1-216-807-11 METAL CHIP 68 R950 1-216-809-11 METAL CHIP 100 R951 1-216-807-11 METAL CHIP 68 R951 1-216-809-11 METAL CHIP 100 R952 1-216-807-11 METAL CHIP 68 R952 1-216-809-11 METAL CHIP 100 R953 1-216-810-11 METAL CHIP 120 R953 1-216-811-11 METAL CHIP 150 R954 1-216-811-11 METAL CHIP 150 R954 1-216-812-11 METAL CHIP 180 R959 1-216-864-11 SHORT CHIP 0 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) < TRANSISTOR > Q881 Q882 Q883 8-729-600-22 TRANSISTOR 2SA1235-F 8-729-600-22 TRANSISTOR 2SA1235-F 8-729-600-22 TRANSISTOR 2SA1235-F < RESISTOR > R861 1-216-811-11 METAL CHIP 150 R862 1-216-810-11 METAL CHIP 120 R863 1-216-811-11 METAL CHIP 150 R864 1-216-810-11 METAL CHIP 120 R881 1-216-821-11 METAL CHIP 1K 5% 1/10W (GT31W/GT310) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT31W/GT310) 5% 1/10W R882 R883 R884 R885 R886 1-216-821-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R887 R888 R889 R901 R902 1-216-845-11 1-216-845-11 1-216-845-11 1-216-820-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 820 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R903 R904 R905 R906 R907 1-216-821-11 1-216-822-11 1-216-823-11 1-216-820-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1.2K 1.5K 820 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R908 R909 R910 R911 R912 1-216-821-11 1-216-822-11 1-216-823-11 1-216-824-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1.2K 1.5K 1.8K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 32 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W (GT360/GT360S) CDX-GT31W/GT310/GT360/GT360S KEY Ref. No. Part No. Description Remark R961 1-216-809-11 METAL CHIP 100 R962 1-216-809-11 METAL CHIP 100 R971 R975 R976 1-216-809-11 METAL CHIP 1-216-811-11 METAL CHIP 1-216-811-11 METAL CHIP 100 150 150 R977 R978 R981 R982 R983 1-216-809-11 1-216-864-11 1-218-893-11 1-216-841-11 1-216-864-11 100 0 82K 47K 0 R988 R989 1-216-864-11 SHORT CHIP 1-216-845-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 0 100K 5% 1/10W (GT360/GT360S) 5% 1/10W (GT360/GT360S) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 0.5% 5% 1/10W 1/10W 5% 1/10W Ref. No. MAIN Part No. Description C301 C302 C303 C304 C305 1-115-340-11 1-162-970-11 1-128-551-11 1-115-340-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.22uF 0.01uF 22uF 0.22uF 0.01uF 10% 10% 20% 10% 10% 25V 25V 63V 25V 25V Remark C306 C307 C308 C309 C312 1-124-261-00 1-162-970-11 1-124-261-00 1-115-340-11 1-115-340-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 10uF 0.01uF 10uF 0.22uF 0.22uF 20% 10% 20% 10% 10% 50V 25V 50V 25V 25V C313 C314 C315 C316 C317 1-162-970-11 1-124-261-00 1-162-970-11 1-124-261-00 1-124-257-00 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT 0.01uF 10uF 0.01uF 10uF 2.2uF 10% 20% 10% 20% 20% 25V 50V 25V 50V 50V C318 C319 C320 C325 C329 1-162-923-11 1-127-715-11 1-162-970-11 1-115-340-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47PF 0.22uF 0.01uF 0.22uF 0.01uF 5% 10% 10% 10% 10% 50V 16V 25V 25V 25V C330 C361 C362 C363 C364 1-115-340-11 1-127-715-11 1-127-715-11 1-126-160-11 1-126-160-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT 0.22uF 0.22uF 0.22uF 1uF 1uF 10% 10% 10% 20% 20% 25V 16V 16V 50V 50V C365 C366 C401 C402 C403 1-126-960-11 1-126-960-11 1-124-234-00 1-162-970-11 1-124-584-00 ELECT ELECT ELECT CERAMIC CHIP ELECT 1uF 1uF 22uF 0.01uF 100uF 20% 20% 20% 10% 20% 50V 50V 16V 25V 10V C405 C409 C412 C413 C414 1-124-234-00 1-124-261-00 1-162-970-11 1-163-251-11 1-163-251-11 ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22uF 10uF 0.01uF 100PF 100PF 20% 20% 10% 5% 5% 16V 50V 25V 50V 50V C415 C417 C418 C419 C421 1-162-970-11 1-162-970-11 1-162-966-11 1-162-966-11 1-126-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.01uF 0.01uF 0.0022uF 0.0022uF 10uF 10% 10% 10% 10% 20% 25V 25V 50V 50V 50V C423 C424 C426 C431 C432 1-165-908-11 1-162-927-11 1-165-908-11 1-124-261-00 1-163-251-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 1uF 100PF 1uF 10uF 100PF 10% 5% 10% 20% 5% 10V 50V 10V 50V 50V C434 C441 C443 C444 C445 1-162-927-11 1-126-964-11 1-165-908-11 1-162-927-11 1-165-908-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 10uF 1uF 100PF 1uF 5% 20% 10% 5% 10% 50V 50V 10V 50V 10V C451 C452 C454 C461 C462 1-126-964-11 1-163-251-11 1-162-927-11 1-126-964-11 1-165-908-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 10uF 100PF 100PF 10uF 1uF 20% 5% 5% 20% 10% 50V 50V 50V 50V 10V C463 C471 C472 1-165-908-11 CERAMIC CHIP 1-126-964-11 ELECT 1-165-908-11 CERAMIC CHIP 1uF 10uF 1uF 10% 20% 10% 10V 50V 10V < ROTARY ENCODER > RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME) < SWITCH > S901 S902 S903 S904 S906 1-786-653-11 1-786-653-11 1-786-653-11 1-786-653-11 1-786-653-11 SWITCH, TACTILE (Z) SWITCH, TACTILE (OFF) SWITCH, TACTILE (SOURCE) SWITCH, TACTILE (EQ3) SWITCH, TACTILE (BTM/CAT) (GT31W/GT310) S906 1-786-653-11 SWITCH, TACTILE (BTM) (GT360/GT360S) S907 1-786-653-11 SWITCH, TACTILE (MODE) ************************************************************* A-1203-666-A A-1203-850-A A-1203-878-A A-1203-912-A MAIN BOARD, COMPLETE (GT31W) MAIN BOARD, COMPLETE (GT310) MAIN BOARD, COMPLETE (GT360) MAIN BOARD, COMPLETE (GT360S) ********************* 7-621-284-40 7-685-134-19 7-685-793-09 7-685-795-09 SCREW +P 2.6X10 SCREW +P 2.6X8 TYPE2 NON-SLIT SCREW +PTT 2.6X8 (S) SCREW +PTT 2.6X12 (S) < CAPACITOR > C2 C3 C5 C6 C7 1-126-947-11 1-162-970-11 1-126-947-11 1-162-970-11 1-162-970-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 47uF 0.01uF 47uF 0.01uF 0.01uF 20% 10% 20% 10% 10% 35V 25V 35V 25V 25V C8 C15 C151 C152 C153 1-162-970-11 1-107-826-11 1-126-960-11 1-126-960-11 1-126-961-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 0.01uF 0.1uF 1uF 1uF 2.2uF 10% 10% 20% 20% 20% 25V 16V 50V 50V 50V C154 C155 C200 C201 C202 1-163-017-00 1-163-017-00 1-107-826-11 1-124-234-00 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.0047uF 0.0047uF 0.1uF 22uF 0.1uF 10% 10% 10% 20% 10% 50V 50V 16V 16V 16V C203 C204 C205 C206 C207 1-126-965-11 1-107-826-11 1-126-965-11 1-107-826-11 1-126-965-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT 22uF 0.1uF 22uF 0.1uF 22uF 20% 10% 20% 10% 20% 50V 16V 50V 16V 50V 33 CDX-GT31W/GT310/GT360/GT360S MAIN Ref. No. Part No. Description Part No. Description C473 C484 C485 C486 C491 1-165-908-11 1-107-826-11 1-126-933-11 1-126-964-11 1-124-589-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 1uF 0.1uF 100uF 10uF 47uF 10% 10% 20% 20% 20% 10V 16V 16V 50V 16V Remark D205 D206 D207 D301 D302 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C501 C502 C504 C507 C508 1-162-970-11 1-162-964-11 1-162-970-11 1-162-917-11 1-162-917-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.001uF 0.01uF 15PF 15PF 10% 10% 10% 5% 5% 25V 50V 25V 50V 50V D303 D304 D305 D306 D307 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C509 C510 C512 C513 C514 1-164-227-11 1-165-908-11 1-162-964-11 1-162-970-11 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.022uF 1uF 0.001uF 0.01uF 0.001uF 10% 10% 10% 10% 10% 25V 10V 50V 25V 50V D308 D309 D310 D311 D312 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C519 C600 C601 C622 C623 1-107-826-11 1-126-935-11 1-162-970-11 1-126-924-11 1-126-916-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT 0.1uF 470uF 0.01uF 330uF 1000uF 10% 20% 10% 20% 20% 16V 16V 25V 10V 6.3V D353 D491 D493 D502 D503 6-501-013-01 6-501-193-01 6-501-051-01 8-719-060-48 6-501-193-01 DIODE DIODE DIODE DIODE DIODE BAT54ALT1G 1SS355WTE-17 BAT54CLT1G RB751V-40TE-17 1SS355WTE-17 C681 C682 C683 C701 C702 1-162-970-11 1-162-970-11 1-124-584-00 1-131-868-81 1-164-005-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP 0.01uF 0.01uF 100uF 3300uF 0.47uF 10% 10% 20% 20% 25V 25V 10V 16V 25V D602 D603 D604 D605 D606 6-501-180-01 6-501-169-01 6-501-180-01 6-501-180-01 8-719-072-70 DIODE DIODE DIODE DIODE DIODE UDZW-TE17-18B UDZW-TE17-6.2B UDZW-TE17-18B UDZW-TE17-18B MA2ZD14001S0 C703 C704 C705 C997 C998 1-164-005-11 1-115-340-11 1-115-340-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.47uF 0.22uF 0.22uF 0.001uF 0.001uF 25V 25V 25V 50V 50V D607 D609 D702 D703 D901 8-719-049-38 6-501-051-01 6-501-180-01 6-501-170-01 6-501-180-01 DIODE DIODE DIODE DIODE DIODE 1N5404TU BAT54CLT1G UDZW-TE17-18B UDZW-TE17-6.8B UDZW-TE17-18B C999 1-107-826-11 CERAMIC CHIP D998 D999 6-501-180-01 DIODE UDZW-TE17-18B 6-501-180-01 DIODE UDZW-TE17-18B 0.1uF 10% 10% 10% 10% 10% 16V (GT31W/GT310) Ref. No. < CONNECTOR > CN300 CN350 CN370 CNJ400 1-774-701-21 1-820-611-11 1-820-622-11 1-580-907-41 PIN, CONNECTOR 16P CONNECTOR, BOARD TO BOARD 28P SOCKET, CONNECTOR 20P PLUG, CONNECTOR 8P (BUS CONTROL IN) < DIODE > D2 D101 D103 D104 D105 6-501-168-01 6-501-170-01 6-501-170-01 6-501-170-01 6-501-170-01 DIODE DIODE DIODE DIODE DIODE UDZW-TE17-5.6B UDZW-TE17-6.8B UDZW-TE17-6.8B UDZW-TE17-6.8B UDZW-TE17-6.8B D106 D108 D109 D110 D111 6-501-180-01 6-501-170-01 6-501-170-01 6-501-170-01 6-501-170-01 DIODE DIODE DIODE DIODE DIODE UDZW-TE17-18B UDZW-TE17-6.8B UDZW-TE17-6.8B UDZW-TE17-6.8B UDZW-TE17-6.8B D112 D113 D153 D200 D201 6-501-170-01 6-501-170-01 6-501-170-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE UDZW-TE17-6.8B UDZW-TE17-6.8B UDZW-TE17-6.8B 10EDB40-TA1B2 10EDB40-TA1B2 D202 D203 D204 6-500-522-01 DIODE 10EDB40-TA1B2 6-500-522-01 DIODE 10EDB40-TA1B2 6-500-522-01 DIODE 10EDB40-TA1B2 34 Remark < FUSE > F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A < IC > IC200 IC201 IC202 IC203 IC300 6-709-213-01 6-709-213-01 6-709-213-01 6-709-213-01 6-705-359-02 IC IC IC IC IC NJM2387ADL3(TE2) NJM2387ADL3(TE2) NJM2387ADL3(TE2) NJM2387ADL3(TE2) TDA8588AJ/N2/R1 IC401 IC501 IC601 IC602 IC681 6-710-065-01 6-710-298-01 6-703-884-01 8-759-659-13 6-705-373-01 IC IC IC IC IC BD3442FS-E2 MB90F045PF-G-9015-SPE1 BA8271F-E2 PST3428UL MM3123DPLE < JACK > J1 J652 1-815-185-13 JACK (ANTENNA) 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN L/R, AUDIO OUT REAR L/R) < JUMPER RESISTOR > JC1 JC2 JC3 JC4 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 CDX-GT31W/GT310/GT360/GT360S MAIN Ref. No. Part No. Description Part No. Description JC5 JC6 JC7 JC8 JC9 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 Remark Q420 Q432 Q440 Q452 Q460 8-729-027-44 6-550-752-01 8-729-027-44 6-550-752-01 8-729-027-44 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114TKA-T146 DTC614TKT146 DTC114TKA-T146 DTC614TKT146 DTC114TKA-T146 JC10 JC11 JC12 JC13 JC14 1-216-296-11 1-216-864-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 Q470 Q491 Q492 Q600 Q601 8-729-027-44 8-729-027-23 8-729-027-43 8-729-047-76 8-729-027-23 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114TKA-T146 DTA114EKA-T146 DTC114EKA-T146 FMC2A-T148 DTA114EKA-T146 JC15 JC16 JC17 JC18 JC19 1-216-296-11 1-216-296-11 1-216-864-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 Q605 Q664 Q702 8-729-027-43 TRANSISTOR DTC114EKA-T146 8-729-027-23 TRANSISTOR DTA114EKA-T146 8-729-120-28 TRANSISTOR 2SC1623-L5L6 JC20 JC21 JC22 JC23 JC24 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 R2 R3 R4 R5 R6 1-216-839-11 1-216-843-11 1-216-839-11 1-216-843-11 1-414-595-11 METAL CHIP 33K METAL CHIP 68K METAL CHIP 33K METAL CHIP 68K INDUCTOR, FERRITE BEAD JC25 JC26 JC27 JC29 JC30 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 R7 R9 R10 R12 R13 1-414-595-11 1-216-843-11 1-216-821-11 1-216-811-11 1-216-811-11 JC31 JC32 JC33 JC34 JC35 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 R151 R152 R153 R154 R155 JC36 JC37 JC38 JC40 JC41 1-216-864-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 (GT31W/GT310) 0 0 JC42 1-216-296-11 SHORT CHIP 0 < COIL > L1 L4 L5 L151 L300 1-216-295-11 1-469-844-11 1-216-864-11 1-216-295-11 1-456-617-11 SHORT CHIP INDUCTOR SHORT CHIP SHORT CHIP COIL, CHOKE 0 2.2uH 0 0 L401 L402 L403 L405 L406 1-216-864-11 1-216-295-11 1-216-295-11 1-216-864-11 1-500-245-11 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 INDUCTOR, FERRITE BEAD L407 L409 L410 L501 L901 1-216-864-11 1-469-844-11 1-469-876-11 1-469-844-11 1-216-295-11 SHORT CHIP 0 INDUCTOR 2.2uH INDUCTOR, FERRITE BEAD INDUCTOR 2.2uH SHORT CHIP 0 L902 1-469-844-11 INDUCTOR 2.2uH < TRANSISTOR > Q3 6-551-431-01 TRANSISTOR 2SC6027T100-QR Ref. No. Remark < RESISTOR > 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W INDUCTOR, FERRITE BEAD METAL CHIP 68K METAL CHIP 1K METAL CHIP 150 METAL CHIP 150 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1-216-817-11 1-216-817-11 1-216-834-11 1-216-834-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 12K 12K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R200 R201 R202 R203 R204 1-216-833-11 1-216-822-11 1-216-845-11 1-216-829-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 1.2K 100K 4.7K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R205 R206 R207 R208 R209 1-216-845-11 1-216-822-11 1-216-821-11 1-218-344-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 1.2K 1K 7.5K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R210 R211 R301 R302 R351 1-216-812-11 1-216-821-11 1-216-811-11 1-216-841-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 180 1K 150 47K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R355 R356 R357 R358 R401 1-216-833-11 1-216-833-11 1-216-821-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R402 R420 R421 R430 R431 1-216-821-11 1-216-809-11 1-216-821-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 100 1K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R440 R442 R447 1-216-809-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-833-11 METAL CHIP 100 1K 10K 5% 5% 5% 1/10W 1/10W 1/10W 35 CDX-GT31W/GT310/GT360/GT360S Ver. 1.4 MAIN SERVO Ref. No. Part No. Description Part No. Description R448 R449 R450 R451 R452 1-216-833-11 1-216-833-11 1-216-833-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R561 R563 R565 R566 R567 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R460 R461 R462 R470 R471 1-216-809-11 1-216-821-11 1-216-833-11 1-216-809-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 10K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R568 R570 R600 R601 R602 1-216-849-11 1-216-809-11 1-216-845-11 1-216-851-11 1-216-851-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220K 100 100K 330K 330K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R472 R481 R485 R491 R502 1-216-833-11 1-216-801-11 1-218-883-11 1-216-805-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 22 33K 47 100 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R603 R604 R606 R607 R608 1-216-821-11 1-216-835-11 1-216-821-11 1-216-821-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 15K 1K 1K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R503 R504 R505 R507 R509 1-216-809-11 1-218-871-11 1-218-871-11 1-216-845-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 10K 10K 100K 100 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R610 R611 R612 R615 R616 1-216-809-11 1-216-864-11 1-216-864-11 1-216-809-11 1-216-864-11 METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP SHORT CHIP 100 0 0 100 0 5% 1/10W 5% 1/10W R510 R511 R512 R517 R519 1-216-864-11 1-216-809-11 1-216-809-11 1-216-841-11 1-216-845-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 100 100 47K 100K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R636 R671 R672 R673 R674 1-216-845-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 100 10K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R520 R521 R522 R523 R524 1-216-809-11 1-216-825-11 1-216-825-11 1-216-809-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 2.2K 2.2K 100 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R705 R706 R707 R708 R709 1-249-425-11 1-216-841-11 1-216-841-11 1-216-829-11 1-216-833-11 CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 47K 47K 4.7K 10K 5% 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R525 R526 R529 R531 R532 1-216-833-11 1-216-845-11 1-216-809-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 100 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R533 R534 R537 1-216-845-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-845-11 METAL CHIP 100K 10K 100K R538 1-216-845-11 METAL CHIP 100K R540 1-216-845-11 METAL CHIP 100K 5% 1/10W 5% 1/10W 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 5% 1/10W R544 R545 1-216-809-11 METAL CHIP 1-216-845-11 METAL CHIP 100 100K R546 1-216-845-11 METAL CHIP 100K R550 1-216-845-11 METAL CHIP 100K R551 1-216-845-11 METAL CHIP 100K R552 1-216-845-11 METAL CHIP 100K R553 R555 R556 R557 1-216-845-11 1-216-845-11 1-216-845-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100 5% 1/10W (GT31W/GT310) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W R558 R560 1-216-833-11 METAL CHIP 1-216-845-11 METAL CHIP 10K 100K 5% 5% 36 Remark 5% 1/10W 5% 1/10W (GT360/GT360S) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT360/GT360S) 5% 1/10W (GT31W/GT310) 1/10W 1/10W Ref. No. Remark < SWITCH > S103 S501 1-786-826-11 SWITCH, TACTILE (RESET) 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (GT360/GT360S) < THERMISTOR (POSITIVE) > TH400 1-803-350-21 THERMISTOR, POSITIVE < TUNER UNIT > TU1 TU1 A-3220-960-B TUNER UNIT (TUX-032) (GT360/GT360S) A-3220-961-B TUNER UNIT (TUX-032) (GT31W/GT310) < VIBRATOR > X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz) X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) ************************************************************* A-1177-201-A SERVO BOARD, COMPLETE ********************** ************************************************************* MISCELLANEOUS *************** 7 1-776-206-21 CORD (WITH CONNECTOR) (POWER) 0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) ************************************************************* CDX-GT31W/GT310/GT360/GT360S Ref. No. Part No. Description Remark ACCESSORIES ************ 1-479-077-13 REMOTE COMMANDER (RM-X151) 2-548-729-01 LID, BATTERY CASE (for RM-X151) 2-698-302-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (GT31W:US) 2-698-302-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH) (GT31W:CND/GT310) 2-698-302-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH, SIMPLIFIED CHINESE) (GT360/GT360S) 2-698-303-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH) (GT31W:US) 2-698-303-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH) (GT31W:CND/GT310) 2-698-303-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH,SIMPLIFIED CHINESE) (GT360/GT360S) 7-682-562-04 SCREW +B 4X10 (GT31W) X-2148-896-1 CASE ASSY (for FRONT PANEL) (EXCEPT US) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 151 152 153 154 155 X-3382-647-1 2-686-802-01 3-246-011-01 A-1082-993-A 3-259-776-01 156 1-776-206-21 CORD (WITH CONNECTOR) (POWER) 151 FRAME ASSY, FITTING COLLAR KEY (FRAME) SCREW ASSY (BS4), FITTING (GT360/GT360S) SCREW (+K 5X8 TP) 152 153 ×2 154 155 ×4 156 37 CDX-GT31W/GT310/GT360/GT360S MEMO 38 CDX-GT31W/GT310/ GT360/GT360S US Model Canadian Model SERVICE MANUAL CDX-GT31W/GT310 E Model CDX-GT360/GT360S Chinese Model Ver. 1.1 2006. 10 CDX-GT360 SUPPLEMENT-1 File this supplement with the service manual. Subject : Production country change. The E model of CDX-GT360S has been changed in the production country to Thailand from China. This service manual, SUPPLEMENT-1 only contains the change. When servicing and inspecting, check the part number of Model Number Label to see if the model is made in Thailand or China. DISCRIMINATION – BOTTOM VIEW – MODEL NUMBER LABEL 2-698-545-0 2-698-531-0 2-886-501-0 :China production model :China production model :Thailand production model 9-887-398-81 1 CDX-GT31W/GT310/GT360/GT360S TABLE OF CONTENTS 1. DIAGRAMS 1-1. 1-2. 1-3. 1-4. 1-5. 1-6. Printed Wiring Board –Main Section– ................................ 4 Schematic Diagram –Main Section (1/3)– .......................... 5 Schematic Diagram –Main Section (2/3)– .......................... 6 Schematic Diagram –Main Section (3/3)– .......................... 7 Printed Wiring Board –Key Section– .................................. 8 Schematic Diagram –Key Section– ..................................... 9 2. EXPLODED VIEWS 2-1. Main Section ..................................................................... 12 2-2. Front Panel Section ........................................................... 13 3. ELECTRICAL PARTS LIST ........................................ 14 2 CDX-GT31W/GT310/GT360/GT360S SECTION 1 DIAGRAMS • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Waveforms — MAIN Board — THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) 1 For schematic diagrams. For printed wiring boards. Note: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • C : panel designation. • A : B+ Line. • B : B– Line. • H : adjustment for repair. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : AM/MW/SW < > : CD PLAY ∗ : Impossible to measure • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. J : CD PLAY F : FM f : AM/MW/SW L : AUX Note: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a : Through hole. • : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) IC501 i; (XOUT) 0.8 Vp-p 32.768 kHz 0.2 V/DIV, 20 µsec/DIV 2 Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. IC501 is (OSC IN) 0.9 Vp-p C Q 18.432 MHz These are omitted B E 0.5 V/DIV, 0.1 µsec/DIV BE C These are omitted ECB These are omitted CDX-GT31W/GT310/GT360/GT360S 3 3 CDX-GT31W/GT310/GT360/GT360S 1-1. PRINTED WIRING BOARD — MAIN SECTION — 2 1 : Uses unleaded solder. 3 4 5 6 7 8 9 10 11 12 13 14 J652 L R CNJ400 (BUS CONTROL IN) -4 C304 C301 C309 IC300 F901 R709 D103 D106 D104 JW4 D110 D112 JW5 JW7 JC25 D113 JC26 R153 D105 C154 C418 C419 R561 (CHASSIS) C705 YEL C417 JW105 IC601 JW106 JW110 D207 JW109 JW108 L405 C415 C402 JW92 R600 IC203 5 R206 D202 D206 D205 1 R210 D201 JW90 R205 JC23 IC200 R201 1 C204 D503 R200 C206 C207 JC2 R533 1 JW93 R208 D203 C202 1 R202 IC201 R203 R204 5 D204 IC202 5 21 R207 S103 J C201 R211 JW84 R532 R517 JC16 R673 FMB3 C401 JC3 Q664 JC41 JW3 C155 C152 R671 D111 JW6 R152 R154 JW2 JW1 L151 D153 D109 C502 R502 D101 D108 C200 JW94 5 JW88 C151 C153 R570 JW82 R503 C514 JC37 D353 R209 D502 JC24 C512 R529 R567 R504 R505 C501 R553 R519 JC17 R672 R522 C513 R565 JC15 JW18 JW17 JW16 JW14 JW13 JW8 JW15 JC27 R521 JW19 H R155 R151 JW80 R674 C519 R351 JW89 R520 L406 CD MECHANISM UNIT (MG-101TA) JW87 JW20 C507 IC501 JW111 R523 R512 IC602 3 2 4 1 L501 JW86 JW21 R610 D609 X501 JW22 R510 C510 JW83 L5 JC13 R524 JC28 I R509 R511 R525 JW11 JW12 R560 JW10 JW9 10K Q601 JW107 CN350 R557 R556 R612 Q600 R401 C509 C504 • Semiconductor Location L410 JW91 R544 JC40 G JW28 R545 JW25 FMB4 JW85 9K JW79 R526 JW26 JW23 R537 JC38 R550 JW29 JW81 JW30 R546 X502 JW27 JC20 R611 JC36 R402 JW78 C508 S501 FREQUENCY SELECT JW113 TH400 R615 R608 R601 JC35 R507 R302 C205 L4 R7 C319 R540 JW31 R602 JC34 JW77 R534 C7 JW75 JW76 C318 JW112 R6 JW74 R616 D604 C601 L402 R603 D602 R607 R568 L401 R604 Q605 R606 JC19 C403 C363 JC14 C5 R555 L409 R563 JW73 JC4 R13 C8 JW100 JW104 JW95 JC33 C315 C316 L403 JW96 JC18 JW72 JW32 D606 L407 JW71 D493 JC12 JW24 D2 D603 R636 JW70 Q492 R531 D491 C317 JW37 F R12 JW34 L300 JW103 D605 JW68 JW67 C314 C313 JC1 Q491 R301 JW35 D304 JW98 JW69 R566 JW33 D303 D302 C412 JW44 Q3 C702 C703 D311 D307 JW66 C682 L901 JW36 C2 D301 D607 L1 C6 YEL JW64 JW65 JW63 JW62 JW61 JW60 JW58 C491 R491 JW42 R10 D702 JW97 C364 C3 C681 C683 JC8 JW43 JW41 R9 JW40 JW39 JC5 R5 JW57 C308 JW45 R3 C431 R4 JC21 R707 JW99 JC32 C306 R451 R431 C600 C704 R708 D310 IC681 JW46 C451 C15 R452 R430 C471 C461 R471 IC401 JW38 R470 R2 JW56 R481 R461 JW102 D703 C701 R705 R440 JC42 R485 E C622 R420 R460 4 C997 Q702 D312 JW47 5 R706 L902 C365 C366 C484 C361 D306 JC7 C362 TU1 D305 C485 C486 D C623 R355 R356 JW55 JC9 JC6 6 JW101 C312 C473 C472 R472 JW48 1 JC22 D998 D309 Q470 C JW54 C463 C454 D308 C462 JW59 Q460 C320 JW53 C302 C303 R462 2 7 JW49 C434 JW52 JC10 3 8 C405 Q452 Q432 C305 C409 R357 C441 JC11 R358 R447 R448 R421 R442 C432 C421 C414 C307 C452 C998 JW51 C413 B JW50 D200 C325 C329 Q440 Q420 CN300 YEL C330 D901 C423 R450 R449 C203 C426 D999 C445 C443 JC30 -3 JC29 -2 JC31 R -1 C444 L C424 J1 (ANTENNA) A AUDIO OUT REAR BUS AUDIO IN CN370 S103 RESET X501 (Page 8) CDX-GT31W/GT310/GT360/GT360S 4 4 1-871-263- (21) Ref. No. D2 D101 D103 D104 D105 D106 D108 D109 D110 D111 D112 D113 D153 D200 D201 D202 D203 D204 D205 D206 D207 D301 D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D353 D491 D493 D502 D503 Location F-3 I-4 I-3 I-3 I-3 I-3 I-3 I-4 I-4 I-4 I-4 I-4 I-2 H-11 H-10 H-10 I-10 I-9 I-9 I-9 G-10 C-8 D-8 C-9 D-9 C-6 C-6 C-6 C-6 C-7 C-7 C-8 D-7 G-8 E-5 E-6 H-7 I-6 Ref. No. D602 D603 D604 D605 D606 D607 D609 D702 D703 D901 D998 D999 Location D-10 D-10 E-10 D-10 D-10 D-10 F-9 C-8 C-9 B-10 C-9 B-9 IC200 IC201 IC202 IC203 IC300 IC401 IC501 IC601 IC602 IC681 G-11 I-10 I-7 H-9 B-6 D-3 G-6 E-10 G-8 D-6 Q3 Q420 Q432 Q440 Q452 Q460 Q470 Q491 Q492 Q600 Q601 Q605 Q664 Q702 F-3 B-4 B-3 B-4 B-3 C-4 C-4 E-6 E-6 E-10 E-10 D-10 I-6 C-8 CDX-GT31W/GT310/GT360/GT360S 1-2. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 10 for IC Block Diagrams. C303 C302 JC29 C325 C444 JC30 C330 C424 L901 C308 C306 C304 JC31 C301 C309 IC B/D C305 C307 C317 IC300 R302 C319 C318 C434 JC12 C312 C320 C314 C316 JC13 D304 D303 D306 D305 D308 D307 C997 D309 D998 D310 C998 D311 C315 R709 D312 D999 R705 C313 D301 C454 D302 R301 CN300 D702 D703 F901 D607 JC33 C704 C701 JC32 L902 C705 L300 R491 JC8 D491 JC9 IC602 R707 R706 C702 C703 (Page 6) IC681 Q491 Q702 Q492 D493 R708 JC1 R604 R608 D602 Q600 C600 Q605 R610 C601 R612 CNJ400 JC22 JC21 R611 R616 D901 C329 R531 D603 Q601 TH400 R607 R602 R601 JC36 R606 D605 D604 D606 JC20 R615 IC B/D C683 R600 R603 IC601 D609 (Page 7) CDX-GT31W/GT310/GT360/GT360S 5 5 C682 C681 C491 C622 C623 CDX-GT31W/GT310/GT360/GT360S 1-3. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 10 for IC Block Diagrams. J652 J1 C445 C443 C426 C423 C463 C462 C473 C472 C362 C361 C452 C432 C413 C414 R3 TU1 Q470 Q460 Q420 Q440 Q452 Q432 C15 R2 JC11 R357 JC10 R4 R358 R5 R355 R472 R448 R462 R471 R461 C471 C461 R447 R421 R442 C421 C441 R449 JC6 R356 R450 JC7 R451 R9 C365 C366 R431 C431 C451 JC5 C3 Q3 L1 C2 R10 C7 C5 C6 D2 IC B/D IC401 R13 C486 R12 C8 C485 L4 R6 C484 R7 R420 R481 R440 R460 R470 R452 JC42 (Page 5) C364 C363 R430 R485 L5 R558 JC28 IC B/D IC B/D IC B/D IC203 IC B/D IC200 D113 IC201 IC202 CN370 JC41 D207 D101 R205 R204 R202 R200 R201 D112 R203 C201 D201 R207 C203 D203 D204 D206 R206 R210 R209 C207 D111 JC26 D110 D109 R208 R211 C206 JC25 C200 D200 D202 D205 C202 D108 C205 C204 D103 D105 D104 D106 D153 C151 C152 C153 (Page 7) CDX-GT31W/GT310/GT360/GT360S 6 6 R151 R154 R153 C154 R155 L151 R152 C155 (Page 9) CDX-GT31W/GT310/GT360/GT360S 1-4. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 3 for Waveforms. (Page 6) (Page 5) C509 R553 R533 R519 R672 R561 R517 R529 JC24 X502 Q664 R570 C507 R532 JC2 D502 R674 C519 R568 JC37 JC17 C508 JC19 JC16 CN350 X501 R565 C403 JC34 R509 R555 C412 JC35 L407 L501 R567 L402 C417 L409 L401 C405 R402 C510 C502 L410 L403 L405 C409 C415 C514 D503 R540 C419 R671 R673 JC23 R401 C418 JC3 R505 R503 R526 IC501 L406 R502 R636 R351 JC15 C513 R563 C401 R504 C512 C501 JC18 R522 C402 R521 R566 R520 R523 R524 D353 R534 R550 R537 R507 R545 R546 JC40 JC4 R560 CDX-GT31W/GT310/GT360/GT360S 7 7 R512 R511 R510 C504 JC27 R544 R556 JC14 R557 S501 S103 R525 CDX-GT31W/GT310/GT360/GT360S 1-5. PRINTED WIRING BOARD — KEY SECTION — 2 1 S902 4 LED961-963 (RING ILLUMINATION) R903 10 11 12 13 LED941 S901 LED942 (CD INDICATOR) LED941, S901 LED946 LED942 S903 R962 LSW902 9 R961 S904 8 R942 LED961 LED944 B 7 R943 R904 LED944, S904 EQ3 6 LED946, S903 SOURCE LSW901 M> SEEK+ LED943 OFF 5 R941 LED943, S902 3 R902 A : Uses unleaded solder. LSW902 LSW901 R947 SEEK– S906 R908 2 3 IC971 D S908 S911 S912 S913 S914 LED957 S910 R954 S909 LED956 R909 LED955 S907 LED954 R977 1 LED953 IC971 4 LED952 C974 LED951 LED947 LED950 LED945, S906 BTM R906 R907 LED962 LED945 C LED963 S915 11 R953 1-871-262- LED947, LED950, S908 S907 MODE DSPL/DIM LED951, S909 1/ALBM– LED952, S910 2/ALBM+ LED953, S911 3/REP LED956 S914 6/PAUSE LED955 S913 5 LED954, S912 4/SHUF (11) LED957, S915 SCRL (Page 4) MAIN BOARD CN370 3 38 R881 R889 Q883 R882 FB901 IC972 C976 R978 D906 C982 C981 R883 FB902 D907 D908 R885 D903 FB903 D905 R988 4 R884 R983 R971 J901 AUX C975 R989 5 R901 D904 Q881 Q882 R886 R948 D882 R946 RE901 C904 C977 F C992 R887 C991 2 R945 R905 R944 R922 1 R913 R952 R951 R911 R950 CN901 R914 R915 FL901 FLUORESCENT INDICATOR TUBE FB904 R921 R912 R975 R982 R888 R976 D971 R910 E R949 A R981 G RE901 PUSH SELECT (VOLUME) 11 1-871-262- • Semiconductor Location CDX-GT31W/GT310/GT360/GT360S 8 8 Ref. No. D882 D903 D904 D905 D906 D907 D908 D971 Location F-7 F-10 F-9 F-10 F-10 F-10 F-10 E-4 IC971 IC972 C-4 F-10 LED941 LED942 LED943 LED944 LED945 A-12 B-7 A-1 B-2 C-2 Ref. No. LED946 LED947 LED950 LED951 LED952 LED953 LED954 LED955 LED956 LED957 LED961 LED962 LED963 Location B-4 C-4 C-5 C-5 C-6 C-7 C-8 C-9 C-10 C-10 B-3 C-3 C-2 Q881 Q882 Q883 F-8 F-8 F-9 (11) CDX-GT31W/GT310/GT360/GT360S 1-6. SCHEMATIC DIAGRAM — KEY SECTION — R981 R978 R941 LED946 R943 R949 R947 R951 LED961 R953 C976 R942 LED944 R945 LSW901(1/2) LED950 LED953 LED957 IC972 R961 C977 C975 LED941 R944 LED942 R946 LED945 LED947 LED951 R948 LSW902(1/2) R952 R954 LED954 R950 R982 R962 LED956 LED962 R975 R976 R977 IC971 LED943 LED952 LED955 LED963 D971 C992 C974 C991 C982 CN901 D908 R886 R922 R901 R971 R902 R903 Q883 RE901 R888 D904 R889 R983 R887 C904 FB904 R921 R905 R904 R988 R884 D903 R882 R907 R908 R909 R910 R911 R912 R913 R914 R915 S908 S909 S910 S911 S912 S913 S914 S915 LSW902(2/2) LSW901(2/2) D907 D906 D905 R906 S907 Q881 (Page 6) C981 Q882 D882 S906 S904 S903 S902 S901 R885 R883 R881 FB903 FB902 FB901 FL901 J901 CDX-GT31W/GT310/GT360/GT360S 9 9 R989 CDX-GT31W/GT310/GT360/GT360S • IC BLOCK DIAGRAMS IC300 TDA8588AJ/N2/R1 (MAIN Board (1/3)) IC601 BA8271F-E2 (MAIN Board (1/3)) TAB 1 2 SDA OUT-FL- 3 BUS ON 1 BUS ON SWITCH RST 2 RESET SWITCH BATT 3 BATTERY SWITCH 14 VCC I2C BUS 4 SCL FL OUT-FL+ 5 6 VP2 OUT-RL- 7 RL MUTE 10 SVR PROTECTION/ DIAGNOSTIC IN-RR 15 CLK 4 VREF 5 DATA 6 9 DATA IN GND 7 8 DATA OUT 12 IN-FL 14 IN-FR MUTE S-GND 13 RESET BUS ON CLK IN BU IN 8 PGND3 OUT-RL+ 9 IN-RL 11 13 12 11 10 16 BEEP VP OUT-RR+ 17 18 PGND2 RR OUT-RR- 19 20 VP1 OUT-FR+ 21 FR OUT-FR- 23 STANDBY/ MUTE 22 STB CHIP DETECT/ DIAGNOSTIC 24 PGND1 BATTERY DETECTION DIAG 25 TEMPERATURE PROTECTION IC200 IC201 IC202 IC203 ENABLE LOGIC 26 RST ANT-REM 27 SWITCH AMP-REM 29 SWITCH NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) CURRENT LIMIT 28 CRES REGULATOR 30 AUDIO8.3V SERVO5V 31 MECH6V 33 32 GND OVERVOLTAGE PROTECTION 34 PANEL+B VP 35 REFERENCE VOLTAGE B.UP+B 37 REGULATOR BANDGAP REFERENCE 36 CBU LOADDUMP PROTECTION THERMAL PROTECTION BACK-UP SWITCH CDX-GT31W/GT310/GT360/GT360S 10 10 1 2 3 4 5 VIN CONTROL VOUT VADJ GND CDX-GT31W/GT310/GT360/GT360S IC401 BD3442FS-E2 (MAIN Board (2/3)) BUS-RCH 1 VCC2 32 F2L 100k 31 GND BUS-LCH 2 100k TU-RCH 3 INPUT SELECTOR INPUT GAIN VOLUME1 /MUTE TREBLE /BASS /MIDDLE VOLUME2 I2C BUS LOGIC 100k TU-LCH 4 30 SDA 29 SCL 28 MUTE 100k CD-RCH 5 VCC 27 VCC 100k CD-LCH 6 FADER 26 OUT-FR 250k FADER 25 OUT-FL 250k FADER 24 OUT-RR FADER 23 OUT-RL 100k EFFECT AUX-RCH 7 AUX-GND 8 AUX-LCH 9 250k DS3-L 10 22 SUBOUT-R DS1-L 11 FADER DS2-L 12 LPF 21 SUBOUT-L EBIAS 13 FADER 20 ADJ DS2-R 14 DS1-R 15 DS3-R 16 19 SAOUT SPECTRUM ANALYZER 18 SADA 17 SACLK 11 CDX-GT31W/GT310/GT360/GT360S SECTION 2 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • -XX and -X mean standardized parts, so they may have some difference from the original one. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color Accessories are given in the last of this parts list. • • 2-1. MAIN SECTION not supplied A MG-101TA-188//Q #2 7 #1 #3 B A #4 #5 F901 #4 4 #3 #4 #4 not supplied 5 not supplied 3 6 #1 TU1 not supplied B 2 #1 not supplied #1 1 Ref. No. Part No. Description 1 2 3 4 5 X-2148-784-1 3-042-244-11 X-2108-670-1 2-050-124-01 A-1206-390-A PANEL (FL) ASSY, SUB SCREW (T) LOCK ASSY (S) SCREW +BTT 2.6X5 MAIN BOARD, COMPLETE 6 7 2-021-848-01 SHEET (TU), GROUND 1-833-100-11 CORD (WITH CONNECTOR) (POWER) 12 Remark Ref. No. Part No. Description F901 TU1 #1 #2 #3 1-532-877-11 A-3220-960-B 7-685-792-09 7-685-790-01 7-685-793-09 FUSE (BLADE TYPE) (AUTO FUSE) 10A TUNER UNIT (TUX-032) SCREW +PTT 2.6X6 (S) SCREW +PTT 2.6X4 (S) SCREW +PTT 2.6X8 (S) #4 #5 7-685-794-09 SCREW +PTT 2.6X10 (S) 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT Remark CDX-GT31W/GT310/GT360/GT360S 2-2. FRONT PANEL SECTION 57 56 RE901 not supplied 57 58 not supplied (KEY board) FL901 J901 55 not supplied not supplied 52 54 not supplied not supplied 53 51 59 Ref. No. Part No. Description 51 52 53 54 55 A-1206-392-A X-2149-355-1 X-2149-359-2 X-2149-353-1 2-693-599-01 PANEL COMPLETE ASSY, FRONT BUTTON ASSY (S) PANEL (SV) ASSY, FRONT KNOB (VOL) (SV) ASSY SPRING (RELEASE) 56 2-684-632-01 PANEL (FL), BACK Remark Ref. No. Part No. Description 57 58 59 FL901 J901 3-250-543-21 X-2149-228-1 3-251-320-01 1-519-909-11 1-820-624-11 SCREW (+B P-TITE M2) CASE ASSY (for FRONT PANEL) EMBLEM (NO. 2.5), SONY INDICATOR TUBE, FLUORESCENT JACK (SMALL TYPE) (VERTICAL) (AUX) Remark RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME) 13 CDX-GT31W/GT310/GT360/GT360S SECTION 3 KEY ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable Ref. No. Part No. • • • • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. CAPACITORS uF : µF COILS uH : µH Description Remark KEY BOARD ********** < CAPACITOR > C904 C974 C975 C976 C977 1-165-176-11 1-107-826-11 1-107-826-11 1-107-826-11 1-125-891-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.1uF 0.1uF 0.1uF 0.47uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 10V C981 C982 C991 C992 1-107-826-11 1-107-826-11 1-216-295-11 1-216-295-11 CERAMIC CHIP CERAMIC CHIP SHORT CHIP SHORT CHIP 0.1uF 0.1uF 0 0 10% 10% 16V 16V < CONNECTOR > CN901 Ref. No. Part No. Description LED944 LED945 LED946 LED947 LED950 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 LED LED LED LED LED SML-310VTT86 (EQ3) SML-310VTT86 (BTM) SML-310VTT86 (SOURCE) SML-310VTT86 (MODE) SML-310VTT86 (DSPL/DIM) LED951 LED952 LED953 LED954 LED955 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 LED LED LED LED LED SML-310VTT86 (1/ALBM –) SML-310VTT86 (2/ALBM +) SML-310VTT86 (3/REP) SML-310VTT86 (4/SHUF) SML-310VTT86 (5) LED956 LED957 LED961 LED962 LED963 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 LED LED LED LED LED SML-310VTT86 (6/PAUSE) SML-310VTT86 (SCRL) SML-310VTT86 (RING ILLMINATION) SML-310VTT86 (RING ILLMINATION) SML-310VTT86 (RING ILLMINATION) 1-820-619-11 PLUG, CONNECTOR 20P < DIODE > D882 D903 D904 D905 D906 8-719-057-80 8-719-057-80 8-719-057-80 8-719-977-12 8-719-977-12 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX MA8180-M-TX MA8180-M-TX DTZ6.8B DTZ6.8B D907 D908 D971 8-719-977-12 DIODE DTZ6.8B 8-719-977-12 DIODE DTZ6.8B 8-719-420-90 DIODE MA8051-M When indicating parts by reference number, please include the board. Remark < SWITCH > LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED) (M > SEEK+) LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (. m SEEK–) < TRANSISTOR > Q881 Q882 Q883 8-729-600-22 TRANSISTOR 2SA1235-F 8-729-600-22 TRANSISTOR 2SA1235-F 8-729-600-22 TRANSISTOR 2SA1235-F < RESISTOR > < FERRITE BEAD > FB901 FB902 FB903 FB904 1-216-864-11 1-216-864-11 1-216-295-11 1-469-876-11 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 INDUCTOR, FERRITE BEAD < FLUORESCENT INDICATOR TUBE > FL901 1-519-909-11 INDICATOR TUBE, FLUORESCENT < IC > IC971 IC972 6-600-163-01 IC RS-770 (IR) 6-706-715-01 IC NJM2867F33(TE2) < DIODE > LED941 8-719-053-09 LED SML-310VTT86 (Z) LED942 8-719-053-09 LED SML-310VTT86 (CD INDICATOR) LED943 8-719-053-09 LED SML-310VTT86 (OFF) 14 R881 R882 R883 R884 R885 1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R886 R887 R888 R889 R901 1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-820-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 100K 100K 820 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R902 R903 R904 R905 R906 1-216-821-11 1-216-821-11 1-216-822-11 1-216-823-11 1-216-820-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1.2K 1.5K 820 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R907 R908 1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP 1K 1K 5% 5% 1/10W 1/10W CDX-GT31W/GT310/GT360/GT360S KEY Ref. No. Part No. Description R909 R910 R911 R912 R913 1-216-822-11 1-216-823-11 1-216-824-11 1-216-825-11 1-216-827-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.2K 1.5K 1.8K 2.2K 3.3K 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W R914 R915 R921 R922 R941 1-216-828-11 1-216-830-11 1-216-295-11 1-216-295-11 1-216-813-11 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP 3.9K 5.6K 0 0 220 5% 5% 1/10W 1/10W 5% 1/10W R942 R943 R944 R945 R946 1-216-813-11 1-216-812-11 1-216-811-11 1-216-812-11 1-216-811-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220 180 150 180 150 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R947 R948 R949 R950 R951 1-216-812-11 1-216-811-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 180 150 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R952 R953 R954 R961 R962 1-216-809-11 1-216-812-11 1-216-811-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 180 150 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R971 R975 R976 R977 R978 1-216-809-11 1-216-811-11 1-216-811-11 1-216-809-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 100 150 150 100 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R981 R982 R983 R988 R989 1-218-893-11 1-216-841-11 1-216-864-11 1-216-864-11 1-216-845-11 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP 82K 47K 0 0 100K 0.5% 5% 1/10W 1/10W 5% 1/10W < ROTARY ENCODER > RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME) < SWITCH > S901 S902 S903 S904 S906 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 SWITCH, TACTILE (Z) SWITCH, TACTILE (OFF) SWITCH, TACTILE (SOURCE) SWITCH, TACTILE (EQ3) SWITCH, TACTILE (BTM) S907 S908 S909 S910 S911 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 SWITCH, TACTILE (MODE) SWITCH, TACTILE (DSPL/DIM) SWITCH, TACTILE (1/ALBM –) SWITCH, TACTILE (2/ALBM +) SWITCH, TACTILE (3/REP) S912 1-786-653-21 SWITCH, TACTILE (4/SHUF) S913 1-786-653-21 SWITCH, TACTILE (5) S914 1-786-653-21 SWITCH, TACTILE (6/PAUSE) S915 1-786-653-21 SWITCH, TACTILE (SCRL) ************************************************************* Ref. No. Part No. Description MAIN Remark A-1206-390-A MAIN BOARD, COMPLETE ********************* 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-794-09 SCREW +PTT 2.6X10 (S) < CAPACITOR > C2 C3 C5 C6 C7 1-126-947-11 1-162-970-11 1-126-947-11 1-162-970-11 1-162-970-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 47uF 0.01uF 47uF 0.01uF 0.01uF 20% 10% 20% 10% 10% 35V 25V 35V 25V 25V C8 C15 C151 C152 C153 1-162-970-11 1-107-826-11 1-126-960-11 1-126-960-11 1-126-961-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 0.01uF 0.1uF 1uF 1uF 2.2uF 10% 10% 20% 20% 20% 25V 16V 50V 50V 50V C154 C155 C200 C201 C202 1-163-017-00 1-163-017-00 1-107-826-11 1-124-234-00 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.0047uF 0.0047uF 0.1uF 22uF 0.1uF 10% 10% 10% 20% 10% 50V 50V 16V 16V 16V C203 C204 C205 C206 C207 1-126-965-11 1-107-826-11 1-126-965-11 1-107-826-11 1-126-965-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT 22uF 0.1uF 22uF 0.1uF 22uF 20% 10% 20% 10% 20% 50V 16V 50V 16V 50V C301 C302 C303 C304 C305 1-115-340-11 1-162-970-11 1-128-551-11 1-115-340-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.22uF 0.01uF 22uF 0.22uF 0.01uF 10% 10% 20% 10% 10% 25V 25V 63V 25V 25V C306 C307 C308 C309 C312 1-124-261-00 1-162-970-11 1-124-261-00 1-115-340-11 1-115-340-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 10uF 0.01uF 10uF 0.22uF 0.22uF 20% 10% 20% 10% 10% 50V 25V 50V 25V 25V C313 C314 C315 C316 C317 1-162-970-11 1-124-261-00 1-162-970-11 1-124-261-00 1-124-257-00 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT 0.01uF 10uF 0.01uF 10uF 2.2uF 10% 20% 10% 20% 20% 25V 50V 25V 50V 50V C318 C319 C320 C325 C329 1-162-923-11 1-127-715-11 1-162-970-11 1-115-340-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47PF 0.22uF 0.01uF 0.22uF 0.01uF 5% 10% 10% 10% 10% 50V 16V 25V 25V 25V C330 C361 C362 C363 C364 1-115-340-11 1-127-715-11 1-127-715-11 1-126-160-11 1-126-160-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT 0.22uF 0.22uF 0.22uF 1uF 1uF 10% 10% 10% 20% 20% 25V 16V 16V 50V 50V C365 C366 C401 C402 C403 1-126-960-11 1-126-960-11 1-124-234-00 1-162-970-11 1-124-584-00 ELECT ELECT ELECT CERAMIC CHIP ELECT 1uF 1uF 22uF 0.01uF 100uF 20% 20% 20% 10% 20% 50V 50V 16V 25V 10V C405 1-124-234-00 ELECT 22uF 20% 16V 15 CDX-GT31W/GT310/GT360/GT360S MAIN Ref. No. Part No. Description C409 C412 C413 C414 C415 1-124-261-00 1-162-970-11 1-163-251-11 1-163-251-11 1-162-970-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.01uF 100PF 100PF 0.01uF 20% 10% 5% 5% 10% 50V 25V 50V 50V 25V C417 C418 C419 C421 C423 1-162-970-11 1-162-966-11 1-162-966-11 1-126-964-11 1-165-908-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 0.0022uF 0.0022uF 10uF 1uF 10% 10% 10% 20% 10% 25V 50V 50V 50V 10V C424 C426 C431 C432 C434 1-162-927-11 1-165-908-11 1-124-261-00 1-163-251-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 100PF 1uF 10uF 100PF 100PF 5% 10% 20% 5% 5% 50V 10V 50V 50V 50V C441 C443 C444 C445 C451 1-126-964-11 1-165-908-11 1-162-927-11 1-165-908-11 1-126-964-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 10uF 1uF 100PF 1uF 10uF 20% 10% 5% 10% 20% 50V 10V 50V 10V 50V C452 C454 C461 C462 C463 1-163-251-11 1-162-927-11 1-126-964-11 1-165-908-11 1-165-908-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 100PF 100PF 10uF 1uF 1uF 5% 5% 20% 10% 10% 50V 50V 50V 10V 10V C471 C472 C473 C484 C485 1-126-964-11 1-165-908-11 1-165-908-11 1-107-826-11 1-126-933-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 10uF 1uF 1uF 0.1uF 100uF 20% 10% 10% 10% 20% 50V 10V 10V 16V 16V C486 C491 C501 C502 C504 1-126-964-11 1-124-589-11 1-162-970-11 1-162-964-11 1-162-970-11 ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 47uF 0.01uF 0.001uF 0.01uF 20% 20% 10% 10% 10% 50V 16V 25V 50V 25V C507 C508 C509 C510 C512 1-162-917-11 1-162-917-11 1-164-227-11 1-165-908-11 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 15PF 15PF 0.022uF 1uF 0.001uF 5% 5% 10% 10% 10% 50V 50V 25V 10V 50V C513 C514 C519 C600 C601 1-162-970-11 1-162-964-11 1-107-826-11 1-126-935-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 0.001uF 0.1uF 470uF 0.01uF 10% 10% 10% 20% 10% 25V 50V 16V 16V 25V C622 C623 C681 C682 C683 1-126-924-11 1-126-916-11 1-162-970-11 1-162-970-11 1-124-584-00 ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT 330uF 1000uF 0.01uF 0.01uF 100uF 20% 20% 10% 10% 20% 10V 6.3V 25V 25V 10V C701 C702 C703 C704 C705 1-131-868-81 1-164-005-11 1-164-005-11 1-115-340-11 1-115-340-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 3300uF 0.47uF 0.47uF 0.22uF 0.22uF 20% 10% 10% 16V 25V 25V 25V 25V C997 C998 1-163-009-11 CERAMIC CHIP 1-163-009-11 CERAMIC CHIP 0.001uF 0.001uF 10% 10% 50V 50V 16 Remark Ref. No. Part No. Description Remark < CONNECTOR > CN300 CN350 CN370 CNJ400 1-774-701-21 1-820-611-11 1-820-622-11 1-580-907-41 PIN, CONNECTOR 16P CONNECTOR, BOARD TO BOARD 28P SOCKET, CONNECTOR 20P PLUG, CONNECTOR 8P (BUS CONTROL IN) < DIODE > D2 D101 D103 D104 D105 8-719-977-03 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 DIODE DIODE DIODE DIODE DIODE DTZ5.6B DTZ6.8B DTZ6.8B DTZ6.8B DTZ6.8B D106 D108 D109 D110 D111 8-719-057-80 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX DTZ6.8B DTZ6.8B DTZ6.8B DTZ6.8B D112 D113 D153 D200 D201 8-719-977-12 8-719-977-12 8-719-977-12 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE DTZ6.8B DTZ6.8B DTZ6.8B 10EDB40-TA1B2 10EDB40-TA1B2 D202 D203 D204 D205 D206 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 D207 D301 D302 D303 D304 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 D305 D306 D307 D308 D309 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 D310 D311 D312 D353 D491 6-500-522-01 6-500-522-01 6-500-522-01 6-501-013-01 6-501-193-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 BAT54ALT1G 1SS355WTE-17 D493 D502 D503 D602 D603 6-501-051-01 8-719-060-48 6-501-193-01 8-719-057-80 8-719-422-64 DIODE DIODE DIODE DIODE DIODE BAT54CLT1G RB751V-40TE-17 1SS355WTE-17 MA8180-M-TX MA8062-M D604 D605 D606 D607 D609 8-719-057-80 8-719-057-80 8-719-072-70 6-501-571-01 6-501-051-01 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX MA8180-M-TX MA2ZD14001S0 1N5404-C311-3 BAT54CLT1G D702 D703 D901 D998 D999 8-719-057-80 8-719-977-12 8-719-057-80 8-719-057-80 8-719-057-80 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX DTZ6.8B MA8180-M-TX MA8180-M-TX MA8180-M-TX CDX-GT31W/GT310/GT360/GT360S MAIN Ref. No. Part No. Description Remark Ref. No. Part No. < IC > Description Remark < COIL > IC200 IC201 IC202 IC203 IC300 6-709-213-01 6-709-213-01 6-709-213-01 6-709-213-01 6-705-359-02 IC IC IC IC IC NJM2387ADL3(TE2) NJM2387ADL3(TE2) NJM2387ADL3(TE2) NJM2387ADL3(TE2) TDA8588AJ/N2/R1 L1 L4 L5 L151 L300 1-216-295-11 1-469-844-11 1-216-864-11 1-216-295-11 1-456-617-11 SHORT CHIP INDUCTOR SHORT CHIP SHORT CHIP COIL, CHOKE IC401 IC501 IC601 IC602 IC681 6-710-065-01 6-710-298-01 6-703-884-01 8-759-659-13 6-705-373-01 IC IC IC IC IC BD3442FS-E2 MB90F045PF-G-9015-SPE1 BA8271F-E2 PST3428UL MM3123DPLE L401 L402 L403 L405 L406 1-216-864-11 1-216-295-11 1-216-295-11 1-216-864-11 1-500-245-11 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 INDUCTOR, FERRITE BEAD L407 L409 L410 L501 L901 1-216-864-11 1-469-844-11 1-469-876-11 1-469-844-11 1-216-295-11 SHORT CHIP 0 INDUCTOR 2.2uH INDUCTOR, FERRITE BEAD INDUCTOR 2.2uH SHORT CHIP 0 L902 1-469-844-11 INDUCTOR < JACK > J1 J652 1-815-185-13 JACK (ANTENNA) 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT REAR) < JUMPER RESISTOR > JC1 JC2 JC3 JC4 JC5 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC6 JC7 JC8 JC9 JC10 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC11 JC12 JC13 JC14 JC15 1-216-864-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC16 JC17 JC18 JC19 JC20 1-216-296-11 1-216-864-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC21 JC22 JC23 JC24 JC25 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC26 JC27 JC28 JC29 JC30 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC31 JC32 JC33 JC34 JC35 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC36 JC37 JC40 JC41 JC42 1-216-864-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 0 2.2uH 0 0 2.2uH < TRANSISTOR > Q3 Q420 Q432 Q440 Q452 6-551-431-01 8-729-027-44 6-550-752-01 8-729-027-44 6-550-752-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC6027T100-QR DTC114TKA-T146 DTC614TKT146 DTC114TKA-T146 DTC614TKT146 Q460 Q470 Q491 Q492 Q600 8-729-027-44 8-729-027-44 8-729-027-23 8-729-027-43 8-729-047-76 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114TKA-T146 DTC114TKA-T146 DTA114EKA-T146 DTC114EKA-T146 FMC2A-T148 Q601 Q605 Q664 Q702 8-729-027-23 8-729-027-43 8-729-027-23 8-729-120-28 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA114EKA-T146 DTC114EKA-T146 DTA114EKA-T146 2SC1623-L5L6 < RESISTOR > R2 R3 R4 R5 R6 1-216-839-11 1-216-843-11 1-216-839-11 1-216-843-11 1-414-595-11 METAL CHIP 33K METAL CHIP 68K METAL CHIP 33K METAL CHIP 68K INDUCTOR, FERRITE BEAD 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R7 R9 R10 R12 R13 1-414-595-11 1-216-843-11 1-216-821-11 1-216-811-11 1-216-811-11 INDUCTOR, FERRITE BEAD METAL CHIP 68K METAL CHIP 1K METAL CHIP 150 METAL CHIP 150 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R151 R152 R153 R154 R155 1-216-817-11 1-216-817-11 1-216-834-11 1-216-834-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 12K 12K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R200 R201 R202 R203 R204 1-216-833-11 1-216-822-11 1-216-845-11 1-216-829-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 1.2K 100K 4.7K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R205 R206 1-216-845-11 METAL CHIP 1-216-822-11 METAL CHIP 100K 1.2K 5% 5% 1/10W 1/10W 17 CDX-GT31W/GT310/GT360/GT360S MAIN Ref. No. Part No. Description Part No. Description R207 R208 R209 R210 R211 1-216-821-11 1-218-344-11 1-216-821-11 1-216-812-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 7.5K 1K 180 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R537 R540 R544 R545 R546 1-216-845-11 1-216-845-11 1-216-809-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R301 R302 R351 R355 R356 1-216-811-11 1-216-841-11 1-216-845-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 150 47K 100K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R550 R553 R555 R556 R557 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R357 R358 R401 R402 R420 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 1K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R558 R560 R561 R563 R565 1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R421 R430 R431 R440 R442 1-216-821-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 100 100 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R566 R567 R568 R570 R600 1-216-845-11 1-216-845-11 1-216-849-11 1-216-809-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 220K 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R447 R448 R449 R450 R451 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R601 R602 R603 R604 R606 1-216-851-11 1-216-851-11 1-216-821-11 1-216-835-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330K 330K 1K 15K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R452 R460 R461 R462 R470 1-216-809-11 1-216-809-11 1-216-821-11 1-216-833-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 1K 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R607 R608 R610 R611 R612 1-216-821-11 1-216-829-11 1-216-809-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 1K 4.7K 100 0 0 5% 5% 5% 1/10W 1/10W 1/10W R471 R472 R481 R485 R491 1-216-821-11 1-216-833-11 1-216-801-11 1-218-883-11 1-216-805-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 22 33K 47 5% 5% 5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R615 R616 R636 R671 R672 1-216-809-11 1-216-864-11 1-216-845-11 1-216-809-11 1-216-809-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 100 0 100K 100 100 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R502 R503 R504 R505 R507 1-216-809-11 1-216-809-11 1-218-871-11 1-218-871-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 10K 10K 100K 5% 5% 0.5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R673 R674 R705 R706 R707 1-216-833-11 1-216-845-11 1-249-425-11 1-216-841-11 1-216-841-11 METAL CHIP METAL CHIP CARBON METAL CHIP METAL CHIP 10K 100K 4.7K 47K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W 1/10W 1/10W R509 R510 R511 R512 R517 1-216-809-11 1-216-864-11 1-216-809-11 1-216-809-11 1-216-841-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 100 0 100 100 47K 5% 1/10W R708 R709 1-216-829-11 METAL CHIP 1-216-833-11 METAL CHIP 4.7K 10K 5% 5% 1/10W 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R519 R520 R521 R522 R523 1-216-845-11 1-216-809-11 1-216-825-11 1-216-825-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 2.2K 2.2K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R524 R525 R526 R529 R531 1-216-833-11 1-216-833-11 1-216-845-11 1-216-809-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 100K 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R532 R533 R534 1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-833-11 METAL CHIP 100K 100K 10K 5% 5% 5% 1/10W 1/10W 1/10W 18 Remark Ref. No. Remark < SWITCH > S103 S501 1-786-826-11 SWITCH, TACTILE (RESET) 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) < THERMISTOR (POSITIVE) > TH400 1-803-350-21 THERMISTOR, POSITIVE < TUNER UNIT > TU1 A-3220-960-B TUNER UNIT (TUX-032) < VIBRATOR > X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz) X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) ************************************************************* CDX-GT31W/GT310/GT360/GT360S Ref. No. Part No. Description Remark MISCELLANEOUS *************** 7 1-833-100-11 CORD (WITH CONNECTOR) (POWER) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A J901 1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX) ************************************************************* ACCESSORIES ************ 1-479-077-13 REMOTE COMMANDER (RM-X151) 2-548-729-01 LID, BATTERY CASE (for RM-X151) 2-886-504-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH, SIMPLIFIED CHINESE) 2-886-505-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH,SIMPLIFIED CHINESE) X-2149-228-1 CASE ASSY (for FRONT PANEL) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 151 152 153 154 155 X-3382-647-1 2-686-803-01 3-246-471-01 X-3381-154-1 3-349-410-11 156 1-833-100-11 CORD (WITH CONNECTOR) (POWER) 151 FRAME ASSY, FITTING COLLAR KEY (FRAME) SCREW ASSY (BS4), FITTING BUSHING 152 153 ×2 154 155 ×4 156 19 CDX-GT31W/GT310/GT360/GT360S MEMO 20 CDX-GT31W/GT310/ GT360/GT360S US Model Canadian Model CDX-GT31W/GT310 SERVICE MANUAL E Model CDX-GT360/GT360S Chinese Model Ver. 1.3 2007.03 CDX-GT360 SUPPLEMENT-2 File this supplement with the service manual. Subject: Notes for removal of the OPTICAL PICK-UP added. DISASSEMBLY 1. CHUCKING ARM SUB ASSY 3 chucking arm sub assy 1 spring 2 Note: Have this portion receive the chassis. Note: Have this portion receive the chassis. Note: Be careful not to touch the turn table. 9-887-398-82 CDX-GT31W/GT310/GT360/GT360S 2. SLED MOTOR ASSY 2 three serration screws (M 2 × 3) 3 sled mtor assy 1 spring turn table spring stand Note: Never remove these parts since they were adjusted. stand Note: Place the stand with care not to touch the turn table. Note for Assembly three serration screws (M 2 × 3) sled mtor assy Note: Take care to prevent the chassis from being bent when tightening the three machine screws. 2 CDX-GT31W/GT310/GT360/GT360S 3. OPTICAL PICK-UP SECTION 2 optical pick-up section 1 Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section. 4. OPTICAL PICK-UP 1 pan tapping screw (M 1.4 × 2.5) 2 leaf spring (sub guide) 3 leaf spring (OP) 5 optical pick-up 4 lead screw assy Notes for Assembly Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. There is space at the end of the leaf spring (sub guide) to avoid contact with the slide. 3 CDX-GT31W/GT310/GT360/GT360S REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2006.08 New 1.1 2006.10 Production country change. (SUPPLEMENT-1) 1.2 2006.12 Correction of disassembly of OPTICAL PICK-UP. 1.3 2007.03 Notes for removal of the OPTICAL PICK-UP added. (SUPPLEMENT-2) 1.4 2007. 04 (ENG-07003) KEY BOARD ASSY addition to GT31W and GT310 for service. (ECN-ECC17969) 4