Fire Hoses Couplings Fittings nozzles5 142 DELIVERY HOSES General remarks The raw materials for endless-woven fire hoses are high-tenacity polyester yarn and tubular felt made of high-grade EPMD rubber mixture or polyurethane. High pressure-resistance, extremely high resistance to UV light and ozone, complete with rot resistance and neutral behaviour towards a wide range of different chemicals – all these characteristics give modern polyester hoses a virtually unlimited lifespan and mean that they require only a bare minimum of care and maintenance. On top of this, they offer good flexibility, low height, very limited space requirements and scarcely measurable elongation even when subjected to intensive stressing. 5 Structure The fabric is made on circular looms from twisted high-tenacity polyester yarn – generally in a twill weave so as to preserve the greatest possible abrasion resistance. The fabric is responsible for withstanding the pressure entirely on its own. The inner lining (be it tubular felt made of high-grade EPMD rubber mixture or polyurethane) is incorporated using a special vulcanisation process, and makes the hose completely watertight. Where applied in addition to the above, a polyurethane outer coating enhances the abrasion resistance, and thus also prolongs the lifespan of the hose. Cleaning – Drying – Storage • After use, clean the hoses with water and a soft brush or hose-washing equipment. Soak badly soiled hoses before scrubbing them – never brush them when dry. • Put the hoses under pressure, locate and mark any damaged areas. • After cleaning, dry immediately and carry out any repairs that may be necessary. • Only store away the hoses in the fire station or in the vehicle once they are dry. • The hose store must be dry, well ventilated, and protected from frost and sunlight. Avoid contact with cement and concrete. Water flow rate (l/min) 200 300 400 600 800 1.000 1.200 1.600 pressure drop in bar per 100 m length 42 mm Ø 1,50 3,50 5,30 -----52 mm Ø 0,50 1,10 2,00 4,00 6,50 ---75 mm Ø 0,10 0,20 0,40 0,80 1,40 2,20 3,00 4,50 110 mm Ø ---0,10 0,20 0,20 0,40 0,80 Pressure drop through friction inside fire hoses to ÖNORM F 2105 and DIN 14811 Treatment and care instructions for pressurised fire hoses Excerpt from ÖBFV (the Austrian Fire Service Association), guidelines on the treatment of pressure hoses: • Lay out the hoses without any kinks or twists. • Do not drag hoses across the ground or over any sharp edges. • Never pull any hoses which are full of water but not under pressure. • Do not place them on broken glass, debris, rubble or glowing embers. • Do not allow them to be soiled by caustic or adhesive substances. • Across roadways, lay them at right angles to the road, enclosed by hose protection ramps. • In extreme sub-zero conditions, never interrupt the flow of water. • Never forcibly roll or kink hoses that have frozen. • Do not throw or drop hose-couplings, and always protect them from soiling. • Store hoses in the vehicle in such a way that there is no risk of them being scraped or abraded during transit. FIRE HOSES, COupLInGS, FITTInGS, nOzzLES Fire Hoses 143 Delivery hose "Synthetic Special" Construction: Characteristics: Polyester jacket, circular woven, twill weave inside lining of EPDM-rubber. Economical, flexible, light-weight, space saving, weather resistant, rot and mildew proof, resistant to aging, ozone, seawater and many chemicals, good abrasion resistance. General purpose fire hose for pumps and vehicles. Certified as to DIN 14811:2007 and Austrian Standard ÖNORM F 2105:2007. Testing pressure: 25 bar Bursting Pressure: 50 bar Certifications: Synthetic Special – Coupling system: Storz Order no. 15 m long 201010 201050 201110 201156 20 m long 200906 201020 201053 201120 201152 201157 201220 25 m long 201125 201225 30 m long 201030 201130 201230 Diameter 42 mm 45 mm 52 mm 65 mm 38 mm 42 mm 45 mm 52 mm 65 mm 65 mm 75 mm 52 mm 75 mm 42 mm 52 mm 75 mm Size of Coupling Storz 42 Storz 45 Storz C Storz 65 Storz 38 Storz 42 Storz 45 Storz C Storz 65 Storz B Storz B Storz C Storz B Storz 42 Storz C Storz B Coupling Material Weight Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy 3,7 kg 4,0 kg 4,8 kg 6,2 kg 4,4 kg 4,8 kg 5,2 kg 6,2 kg 7,9 kg 8,2 kg 10,2 kg 7,5 kg 12,5 kg 6,95 kg 8,85 kg 14,70 kg Remarks Austrian Standard and DIN 14811:2007 5 Austrian Standard and DIN 14811:2007 Synthetic Special – Coupling system: British Standard and American nH Standard Order no. 15 m long 200910 20091005 200911 201142 200912 200913 20 m long 200915 200916 201143 201144 201146 201147 25 m long 20114905 30 m long 201149 20114902 Diameter 38 mm 38 mm 38 mm 63 mm 38 mm 38 mm 38 mm 38 mm 63 mm 63 mm 63 mm 63 mm 63 mm 63 mm 63 mm Size of Coupling 1 1/2" 2 1/2" 1 1/2" 2 1/2" 1 1/2" 1 1/2" 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" Coupling Material Weight Light alloy Light alloy Gunmetal Light alloy Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Light alloy Gunmetal 4,7 kg 5,2 kg 5,6 kg 8,7 kg 4,5 kg 5,6 kg 6,1 kg 7,0 kg 11,2 kg 13,0 kg 11,2 kg 13,0 kg 13,8 kg 16,3 kg 18,1 kg Remarks British instantaneous BS 336:1989 British instantaneous BS 336:1989 NH NH British instantaneous British instantaneous BS 336:1989 BS 336:1989 NH NH BS 336:1989 BS 336:1989 BS 336:1989 144 Delivery hose "professional" Premium inside and outside-rubberised delivery hose in a class of its own. Fabric ply: High-strength polyester/polyamide yarn, endlesswoven and completely embedded in the rubber. Inside and outside rubberisation: Top-grade nitrile rubber, pressed through the fabric ply during extrusion; ribbed on the outside so as to give excellent abrasion-resistance and protection against contact heat. Characteristics: Very sturdy and durable hose; resistant to oil, petrol (gasoline) and chemicals; heat and weather proof; no cleaning and drying needed. Standard length: up to 60 m, standard colour: red. Temperature range: -20 °C up to +100 °C. Up to size 75 mm: Testing pressure: 25 bar; Bursting pressure: 50 bar Certifications: DIN 14811:2007; British Standard BS 6391:1983 / Type 3 and other national standards for delivery hose Coupling Material Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Coupling Material Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Light alloy Light alloy Gunmetal Light alloy Gunmetal Gunmetal Light alloy Light alloy Gunmetal Light alloy Light alloy Gunmetal Light alloy Gunmetal Light alloy Weight 5,0 kg 7,0 kg 8,0 kg 11,0 kg 17,0 kg 6,0 kg 9,0 kg 11,0 kg 15,0 kg 23,0 kg 13,0 kg 22,0 kg Weight 5,0 kg 5,0 kg 5,0 kg 5,0 kg 8,0 kg 8,0 kg 5,0 kg 6,0 kg 6,0 kg 6,0 kg 6,0 kg 11,0 kg 11,0 kg 11,0 kg 20,0 kg 7,0 kg 7,0 kg 7,0 kg 7,0 kg 14,0 kg 14,0 kg 9,0 kg 9,0 kg 9,0 kg 9,0 kg 9,0 kg 16,0 kg 16,0 kg 16,0 kg Remarks British instantaneous British instantaneous BS 336:1989 BS 336:1989 BS 336:1989 BS 336:1989 NH British instantaneous British instantaneous BS 336:1989 BS 336:1989 BS 336:1989 BS 336:1989 NH British instantaneous, soft suction British instantaneous BS 336:1989 BS 336:1989 British instantaneous BS 336:1989 BS 336:1989 British instantaneous British instantaneous NH BS 336:1989 BS 336:1989 BS 336:1989 BS 336:1989 NH Remarks professional – Coupling system: Storz Order no. 15 m long 202816 202826 202846 202836 202856 20 m long 202818 202828 202848 202838 202858 30 m long 202829 202839 Order no. 15 m long 202860 202861 202866 202867 202880 202881 202870 20 m long 202862 202863 202868 202869 202883 202884 202882 202859 25 m long 202872 202873 202874 202875 202888 202889 30 m long 202864 202865 202877 202876 202871 202885 202886 202887 Diameter 38 mm 52 mm 65 mm 75 mm 102 mm 38 mm 52 mm 65 mm 75 mm 102 mm 52 mm 75 mm Diameter 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 38 mm 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 65 mm 102 mm 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 38 mm 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 65 mm Size of Coupling Storz 38 Storz C Storz 65 Storz B Storz A Storz 38 Storz C Storz 65 Storz B Storz A Storz C Storz B Size of Coupling 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 1 1/2" 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 4" 1 1/2" 2 1/2" 2 1/2" 1 1/2" 2 1/2" 2 1/2" 1 1/2" 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" soft suction 5 soft suction professional – Coupling system: British Standard and American nH Standard 9 kg 10. Fabric ply: High strength polyester/polyamide yarn. Manufactured according to BS 6391:1983/Type 3. nOzzLES Fire Hoses Delivery hose "professional Light" Inside and outside-rubber lined delivery hose.7 kg 5. Characteristics: Durable and lightweight hose.9 kg 6. professional Light – Coupling system: Storz Order no.1 kg 8. light duty and economical model.7 kg 13. Bursting pressure: 45 bar. heat and weather proof.5 kg Remarks 145 5 Remarks professional Light – Coupling system: British Standard and American nH Standard Order no.9 kg 5.4 kg 6.9 kg 8. Standard length: up to 100 m.9 kg 5.4 kg 6. FITTInGS.6 kg 4.7 kg British instantaneous British instantaneous BS 336:1989 BS 336:1989 BS 336:1989 BS 336:1989 NH British instantaneous British instantaneous BS 336:1989 BS 336:1989 BS 336:1989 BS 336:1989 NH British instantaneous BS 336:1989 BS336:1989 British instantaneous BS 336:1989 BS 336:1989 British instantaneous British instantaneous BS336:1989 BS 336:1989 BS 336:1989 BS336:1989 NH upon special request: "Professional” hoses with British instantaneous and BS 336:1989 couplings can be fitted with rubber protection cuffs.8 kg 7. no cleaning and drying needed.6 kg 7.5 kg 12.0 kg 8.1 kg 19.3 kg 8.9 kg 7.9 kg 12.5 bar. standard colour: red.8 kg 4.0 kg 8. 15 m long 202770 202771 202772 202773 202774 202775 202776 20 m long 202780 202781 202782 202783 202784 202785 202786 25 m long 202790 202791 202792 202793 202794 202795 30 m long 202800 202801 202802 202803 202804 202805 202806 Diameter 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 38 mm 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 65 mm 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 38 mm 38 mm 38 mm 38 mm 65 mm 65 mm 65 mm Size of Coupling 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 1 1/2" 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 1 1/2" 2 1/2" 2 1/2" 1 1/2" 2 1/2" 2 1/2" 1 1/2" 1 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" Coupling Material Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Light alloy Gunmetal Light alloy Gunmetal Gunmetal Light alloy Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Weight 3. petrol (gasoline) and chemicals.8 kg 4.2 kg 6. COupLInGS.5 kg 10.5 kg 4. maximum flexibility and small coil diameter.7 kg 10. resistant to oil. Rubber protection cuff . smooth on the outside for good abrasion and heat resistance. endless-woven and completely embedded in the rubber. Up to size 75 mm: Testing pressure: 22.7 kg 9.5 kg 7. Inside and outside rubberisation: Top-grade nitrile rubber. pressed through the fabric ply during extrusion.9 kg 10.9 kg 3.9 kg 6.1 kg 7.9 kg 14. Temperature range: -20°C up to +100°C.4 kg 6.0 kg 12. 15 m long 202740 202741 202742 202743 20 m long 202750 202751 202752 202753 30 m long 202760 202761 Diameter 38 mm 52 mm 65 mm 75 mm 38 mm 52 mm 65 mm 75 mm 52 mm 75 mm Size of Coupling Storz 38 Storz C Storz 65 Storz B Storz 38 Storz C Storz 65 Storz B Storz C Storz B Coupling Material Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Weight 3.FIRE HOSES. endless-woven in patented special weave with warp threads reinforced.5 kg certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 . made of gunmetal.146 HIGH pRESSuRE DELIVERY HOSES High pressure delivery hose "Synthetic – Rekord H 38" High-pressure hose certified as to ÖNORM F 2105:2007. highly durable EPDM rubberisation.5 kg 3. Testing pressure: 60 bar. easy to repair. 1. Fabric: 100 % polyester yarn. Maximum pressure loads 6 bar.3 kg 10. 32 mm diameter comes with couplings Storz 32. very resistant to ageing.50 kg.0 kg 4. Weight: 9. Remarks certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 certified as to EN ISO 14557:2002 3. (every fourth warp thread is twisted 12-fold).7 kg 6.0 kg 19. made of gunmetal Weight: 7. made of gunmetal.1 kg 5. 206715 Synthetic Mammut H 38. 206610 206715 5 SuCTIOn HOSE Suction hoses – Coupling system: Storz Order no. Weight: 9 kg. 20 m comes with couplings Storz 38.7 kg 9. rot resistant and cold proof. easy to handle.0 m long 21215001 21115001 21015001 21311201 21320501 2. For additional protection. Weight: 6.8 kg 13.0 kg 13.6 m long 21205001 21105001 21005001 21311001 2. 38 mm diameter comes with couplings Storz 38. High pressure hose "Synthetic Mammut H 38" Made of high tenacity Polyester filament yarn. made of gunmetal. the exterior of the hose is covered with black ribbed EPDM rubber. Working pressure: 40 bar. made of gunmetal.0 kg 17.0 kg 15.5 kg 7. Steel wire reinforced.6 kg.05 kg. Certified as to Austrian Standard F 2105:2007. maximum vacuum load 1. bursting pressure: 90 bar Comes with Storz 38 coupling. Characteristics: Greatly enhanced flexibility and abrasion-resistance. burst pressure 90 bar. 20 m. 206710 Synthetic Mammut H 38. care and maintenance-free. 15 m. 15 m.5 m long 21225001 21125001 21025001 21312301 3. 15 m comes with couplings Storz 38.0 kg 11. 38 mm diameter comes with couplings Storz 38. Inner lining: Reinforced.8 bar.0 m long 21235001 21135001 21035001 21314001 Diameter 52 mm 75 mm 110 mm 125 mm 52 mm 75 mm 110 mm 125 mm 150 mm 52 mm 75 mm 110 mm 125 mm 52 mm 75 mm 110 mm 125 mm Size of Coupling Storz C Storz B Storz A Storz 125 Storz C Storz B Storz A Storz 125 Storz 150 Storz C Storz B Storz A Storz 125 Storz C Storz B Storz A Storz 125 Coupling Material Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Weight Made of SBR-Quality (Styrol-Butadien-Caoutchouc). and provided with a high quality EPDM rubber lining. Test pressure 60 bar. made of gunmetal. 206720 Synthetic Mammut H 32.0 kg 19. 206615 Synthetic Rekord H 38.6 kg 17. Weight: 7.05 kg.0 kg 5. giving extra abrasion resistance. 206610 Synthetic Rekord H 38. 1.0 m long 21117001 21291601 21311801 2.5 kg 28.0 kg 26.6 m long 21137001 21107501 21281001 21291101 21316502 21316503 2.0 kg 25.0 kg 17.0 m long 21136301 21285401 21314301 Diameter 75 mm 100 mm 125 mm 75 mm 100 mm 125 mm 75 mm 100 mm 125 mm 75 mm 100 mm 125 mm Size of Coupling NH 2 1/2" NH 4" NH 5" NH 2 1/2" NH 4" NH 5" NH 2 1/2" NH 4" NH 5" NH 2 1/2" NH 4" NH 5" Coupling Material Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Light alloy Weight 6.0 kg Remarks Other dimensions and lengths as well as other coupling systems on request.5 m long 21127001 21283201 21312601 3.0 kg 9. round thread Order no.0 kg 16. FITTInGS.5 kg 19.0 kg 13.0 kg 16.5 m long 21137201 21126501 21283101 21292501 21316201 21316701 3.5 kg 11.0 kg 18.0 kg 17.0 kg 35.5 kg 15.5 kg 10. COupLInGS.0 m long 21137301 21136701 21284001 21284501 21316602 21316603 Diameter 75 mm 75 mm 100 mm 100 mm 140 mm 140 mm 75 mm 75 mm 100 mm 100 mm 140 mm 140 mm 75 mm 75 mm 100 mm 100 mm 140 mm 140 mm 75 mm 75 mm 100 mm 100 mm 140 mm 140 mm Size of Coupling BSRT 3" BSRT 3" BSRT 4" BSRT 4" BSRT 5 1/2" BSRT 5 1/2" BSRT 3" BSRT 3" BSRT 4" BSRT 4" BSRT 5 1/2" BSRT 5 1/2" BSRT 3" BSRT 3" BSRT 4" BSRT 4" BSRT 5 1/2" BSRT 5 1/2" BSRT 3" BSRT 3" BSRT 4" BSRT 4" BSRT 5 1/2" BSRT 5 1/2" Coupling Material Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Light alloy Gunmetal Weight 6.0 kg 13.5 kg 13.5 kg 15.0 kg 12.0 kg Remarks 147 5 Suction Hoses – Coupling system: American nH Standard Order no.FIRE HOSES.0 kg 25.6 m long 21108001 21291301 21311901 2.0 m long 21137101 21116601 21282001 21282101 21316301 21316401 2.0 kg 23.5 kg 23.0 kg 33.5 kg 9.50kg 8.0 kg 23.0 kg 10.0 kg 10.0 kg 16. 1.0 kg 8.0 kg 10.0 kg 16. nOzzLES Fire Hoses Suction hoses – Coupling system: British Standard BS 336:1989.0 kg 9. .0 kg 7. 870 x 520 x 145 mm. Weight: 3 kg.11 kg. rot-proof.13 kg.11 kg. Weight 0.14 kg.75 kg.148 HOSE ACCESSORIES 149010 Suction hose rope with bag Suitable for handling the suction hoses and strainers. 870 x 520 x 115 mm. Weight 0. Weight: 0. Size B. 15 m each.22 kg. Delivered complete with rope bag. 292420 Type "C” Suitable for storing of 3 delivery hoses type C. Suitable for fastening fire hoses to ladders. The carrier consists of a perlon strap 750 mm long and a galvanised grip with clamp. 292430 292460 292420 . The hose jacket is made of light alloy. the other end with loop. Weight 0. Size 38 (1 1/2"). Type "BS” Suitable for storing of 3 delivery hoses type 2 1/2". Recommended Accessory for hose jackets: 295400 + 295200 + 295300 (comes without hose) 295400 Carrying bag Suitable for storing a maximum of 18 hose jackets. Side part foldable. Weight: 0. Hose holder Certified as to DIN 14828:2004.18 kg. Weight: 3. size C. Weight: 0. 52 mm (2"). Hose carrier For easy transport of delivery hoses. 15 m each. Weight: 0. either normally rolled or "Dutch” rolled.5 kg. Weight: 3. Made of Polypropylene plastics. Type "B” Suitable for storing of 2 delivery hoses type B.3 kg. structures etc. Weight 0. Hose holder Suitable for fastening fire hoses to ladders. 295200 295300 295310 295315 295350 Size C. 75 mm (3"). Hose carrying basket Certified as to DIN 14827. 10 mm diameter. Consists of a perlon strap 300 mm long and a galvanised hook with buckle. 870 x 520 x 115 mm.4 kg. Size 65 (2 1/2"). Size 110 mm (4"). One end with wooden twist.5 kg.2 kg. with soft rubber lining for positive sealing. 149010 291900 292200 292200 291900 (comes without hose) 292400 5 292400 Hose jackets Seals punctured fire hose on the spot and allows fire fighting operations to be carried on. Weight: 0. Consists of a Polyester rope 1. structures etc.6 m long. Comes in a length of 15 m and a diameter of 8 mm. Weight 0. 20 m each. Supplied in sets. Each hose bridge accommodates 2 x 1 1/2" or 2 x 2 1/2" hoses. Weight per set: 23 kg. 292701 / 292701005 292702 . with air tires. Frame. as per DIN 14820:2000. The bridges are slip resistant by means of profile inserts.FIRE HOSES. 292515 HOSE BRIDGES 292600 Collapsible wooden hose bridges Certified as to DIN 14820:2000. 292701005 for accommodation of 2 x 4” or 2 x 5” hoses. For fixing on fire trucks. which also act as handles. Made of steel sheet. can be carried in one hand. Supplied in sets. Solid wooden hose bridges for fire hoses. Suitable for accommodating 180 metres of 3" hose. each set consists of 2 hose bridges. Supplied in sets. Weight per set: 23 kg. The links. 292701 for accommodation of 2 x 1 1/2" or 2 x 2 1/2"hoses. 292600 5 292700 Folding heavy-duty rubber hose bridge "Crocodile” Extremely robust and resilient. Weight per set: 19. Compatible with other conventional rubber hose bridges. Each hose bridge accommodates 2 x 11/2" or 2 x 2 1/2" hoses. FITTInGS. each set consists of 2 hose bridges. are used to increase the track width as required. Folding principle saves storage space. Weight: 15 kg. painted fire red and white. Weight per set: 25 kg. nOzzLES Hose Accessories 292510 portable fire hose reel Certified as to DIN 14825:2004-05. painted fire red as per RAL 3000. Dimension: 1300 x 920 x 1370 mm. Suitable for accommodating either 90 metres of 11/2" to 2" hoses or 60 metres of 3" hose. 292700 Heavy-duty rubber hose bridges Solid rubber hose bridges for fire hoses with slip-proof finish.9 kg. with under-strapping made of synthetic yarns. Carrying capacity per hose bridge: 14 tons. Weight per set: 47 kg. made of steel. Reflective strips increase visibility by day and night. Weight: 90 kg. each set consists of 2 hose bridges. 292702 Aluminium hose bridges Heavy duty hose bridges for fire hoses. each set consists of 2 tons hose bridges. Each hose bridge accommodates 2 fire hoses up to 3" diameter. COupLInGS. Comes with 2 carrying handles. 149 292510 292515 Mobile fire hose reel Certified as to DIN 14826:1999-01. Supplied in sets. 60 kg 3. no rotation of seal on seal. Working pressure 16 bar. certified as to EN 1706:1998 and EN 586:2002.42 kg 2.38 kg 0.40 kg 1.20 kg 0.90 kg Blank caps with chain 250000 251000 252000 253000 250500 255200 253480 253500 254000 254100 Storz D Storz C Storz B Storz A Storz 38 Storz 45 Storz 65 Storz 125 Storz 150 Storz 165 25 mm 52 mm 75 mm 110 mm 38 mm 45 mm 65 mm 125 mm 150 mm 165 mm 0. 3 Circlip – prevents the clamp fitting from sliding back on the hose.67 kg 1.20 kg 0.30 kg 0.38 kg 0.22 kg 0.54 kg 0. Coupling system STORz – light alloy Made of aluminium alloy. the tail piece remains stationary. STORz SYSTEM 1 23 4 A symmetrical.40 kg 1.52 kg 1. During coupling the clamp fitting is turned.57 kg 0.48 kg 2.34 kg 0.10 kg 0.09 kg 0.85 kg .10 kg 0. Threads according to ISO 228. no female and male part such as a screw connection. 2) Tail piece.65 kg 1. 4) Washer. enables trouble-free matching of hose ends and connections.30 kg 2. no twisting of the hose. mounted inside the clamp fitting. Quickly coupled by a 120° rotation (click!) and also quickly disconnected.34 kg 0.20 kg 0. The coupling consists of: 1 Clamp fitting.10 kg 0.67 kg 1.30 kg 0.42 kg 0.22 kg 0.60 kg 5 Suction hose couplings 231000 231010 232000 233000 233200 233400 233500 224000 233800 Storz C Storz C Storz B Storz A Storz A Storz 65 Storz 125 Storz 150 Storz 165 52 x 90 mm 38 x 90 mm 75 x 125 mm 110 x 170 mm 100 x 170 mm 65 x 100 mm 127 x 220 mm 150 x 180 mm 150 x 275 mm 0.150 COupLInGS AnD FITTInGS COupLInGS. hermaphrodite coupling.30 kg 2.55 kg 2.35 kg 2.40 kg 0. Washers made of Nitrile rubber Delivery hose couplings 220000 220010 220100 221000 221300 221400 221600 222000 222200 223000 223100 225212 225217 225230 233500 224000 Storz D Storz D Storz D Storz C Storz C Storz C Storz C Storz B Storz B Storz A Storz A Storz 38 Storz 45 Storz 65 Storz 125 Storz 150 25 x 50 mm 25 x 65 mm 19 x 50 mm 52 x 55 mm 52 x 90 mm 38 x 68 mm 25 x 68 mm 75 x 60 mm 75 x 125 mm 110 x 115 mm 101 x 130 mm 38 x 90 mm 45 x 72 mm 65 x 65 mm 127 x 220 mm 150 x 180 mm 0. Weight: 0.4 kg.13 kg 0.08 kg 0. Made of light-alloy.40 kg 0. Made of light-alloy.35 kg 1.50 kg .48 kg 1.91 kg 1.26 kg 0. FITTInGS. Certified as to DIN 14342:2007-10.6 kg.20 kg 0. nOzzLES Couplings and Fittings Adapters 240000 240400 240300 241100 241200 241300 241499 241000 241500 241400 241600 242100 242000 242300 242200 242400 243200 243100 243000 244311 244312 244315 244320 244325 244350 244360 243500 244000 Storz D Storz D Storz D Storz C Storz C Storz C Storz C Storz C Storz C Storz C Storz C Storz B Storz B Storz B Storz B Storz B Storz A Storz A Storz A Storz 38 Storz 38 Storz 38 Storz 45 Storz 45 Storz 65 Storz 65 Storz 125 Storz 150 1" 1" 1 1/4"" 1" 1 1/4" 1 1/2" 1 1/2" 2" 2" 2 1/2" 2 1/2" 2" 2 1/2" 2 1/2" 3" 3" 4" 4" 4 1/2" 1 1/2" 1 1/2" 2" 1 1/2" 2" 2" 2 1/2" 5" 6" female thread male thread female thread female thread female thread female thread male thread female thread male thread female thread male thread female thread female thread male thread female thread male thread male thread female thread female thread female thread male thread female thread female thread female thread female thread female thread female thread female thread 0.60 kg 151 5 Adapters-Reducer 255900 Adapter Storz 38 – D From Storz 38 to Storz D. Weight: 0.20 kg 0.FIRE HOSES.30 kg 0. Weight: 0.40 kg 0.5 kg.06 kg 0. Certified as to DIN 14341:2007-11.21 kg 0.22 kg 0. Made of light-alloy.40 kg 2. Made of light-alloy.4 kg.41 kg 0.28 kg 0. Adapter C – D From Storz C to Storz D.40 kg 0.28 kg 0. COupLInGS.36 kg 0. Certified as to DIN 14343:2008-07.09 kg 0.23 kg 2.65 kg 0.24 kg 0.27 kg 0.18 kg 0. Adapter B – C From Storz B to Storz C. Adapters A – B From Storz A to Storz B.37 kg 0.75 kg 3.36 kg 0.08 kg 0.05 kg 1.15 kg 0. 256000 256100 256200 Coupling adapters 256300 256303 256306 256330 256400 256500 Storz 52 – 38 Storz 52 – 65 Storz 65 – 38 Storz 110 – 65 Storz 125 – 110 Storz 150 – 110 0. Weight: 1. Delivery hose couplings 268700 221610 268712 268710 268720 225205 225214 268715 Storz D Storz C Storz C Storz C Storz B Storz 32 Storz 38 Storz 65 25 x 53 mm 25 x 90 mm 38 x 68 mm 52 x 75 mm 75 x 80 mm 32 x 80 mm 38 x 90 mm 65 x 60 mm 0.26 kg 0.95 kg 0.gunmetal Made of gunmetal. for Storz couplings 020354 276560 276570 276580 276594 276595 Storz 38 Storz D Storz C Storz B Storz 45 Storz 65 1 1/2" 1" 2" 3" 1 1/2" 2 1/2" 0.152 Couplings System STORz .26 kg 0.15 kg 268870 Adapters male/female thread 268800 268808 268810 268812 268813 268811 268820 268825 268830 088129-001 244310 268815 Storz D Storz C Storz C Storz C Storz C Storz C Storz B Storz B Storz A Storz 38 Storz 38 Storz 65 1" 1 1/2" 2" 2" 2 1/2" 2 1/2" 2 1/2" 3" 4" 1 1/2" 1 1/2" 2 1/2" female thread female thread female thread male thread female thread male thread female thread male thread female thread female thread male thread female thread 0.44 kg 0.27 kg 268715 Suction hose couplings 268751 268750 268760 268770 Storz C Storz C Storz B Storz A 38 x 68 mm 52 x 90 mm 75 x 125 mm 110 x 170 mm 0.80 kg 1.008 kg 0.20 kg 0.46 kg 1.80 kg 0.87 kg 5.00 kg 268750 5 Blank caps with chain 268850 268860 268870 268880 021140-001 268865 Storz D Storz C Storz B Storz A Storz 38 Storz 65 25 mm 52 mm 75 mm 110 mm 38 mm 65 mm 0.85 kg 1.09 kg 1.63 kg 0.54 kg 0.23 kg 3. certified as to EN 1982:2007-11 and EN 12420:1999.11 kg 2.60 kg 0.60 kg 1.87 kg 0.003 kg 0. Washers made of Nitrile rubber.015 kg .05 kg 268820 268825 Spare parts for Storz couplings: Washers for delivery operation made of Nitrile rubber.010 kg 0.86 kg 1.56 kg 0.23 kg 0.90 kg 0.41 kg 0. Thread according to ISO 228.004 kg 0.016 kg 0.56 kg 0.88 kg 1.54 kg 1. Working pressure 16 bar. Adapters made of light alloy 244383 244381 277225 277205 244380 277228 277230 244389 277229 244384 244390 244387 244385 256908 256909 256910 24439901 244394 244396 B.80 kg 0. male BSRT .. B.80 kg 1. thread f.. 2 1/2" f. thread m. 1 1/2" f..025 kg 276780 InSTAnTAnEOuS COupLInGS CERTIFIED AS TO BRITISH STAnDARD 336:1989 The British Standard 336:1989 is using on the delivery side the non-symmetrical instantaneous coupling. thread f. thread f.002 kg 0.30 kg 0...016 kg 0... 3" f. thread f. thread 0. B....30 kg 0.25 kg 0. Coupling certified as to BS 336:1989 and non-standardised 11/2" British instantaneous. British Standard pLEASE nOTE: 336:1989 m. The couplings will be disconnected by pulling or twisting release lugs.007 kg 0..005 kg 0...FIRE HOSES. 2 1/2" f...010 kg 0. 1 1/2" m.. Inst.25 kg 0.050 kg 0. thread f. 3" m. B.. On the suction side round threaded suction hose couplings and equipment type BSRT are in use.054 kg 153 Circlips for delivery and suction hose couplings made of steel....020 kg 0. 2 1/2" m. thread f. 4" f.. nOzzLES Couplings and Fittings Washers for delivery and suction hose couplings made of Nitrile rubber. which are simply pushed together. certified as to BS 1490:2002.29 kg 0.65 kg 0.. British Standard f . Inst. 5 1/2" m.60 kg 0. B...60 kg 0. 3" m. BS 336 BS 336 BS 336 BS 336 BS 336 BS 336 BS 336 BS 336 BSRT BSRT BSRT BSRT BSRT BSRT 1 1/2" f. Inst.30 kg 1. for Storz couplings 276670 276680 276690 276700 276710 Storz C Storz B Storz A Storz 125 Storz 150 2" 3" 4" 5" 6" 0.17 kg 0.. thread f. Inst. 1 1/2" m.. 2 1/2" m.80 kg 1. Washers made of Nitrile rubber. COupLInGS.018 kg 0.. British couplings system . Inst.22 kg 0. FITTInGS.... thread f. thread m. Inst... thread f.. Working pressure 15 bar.. swivel 5 1/2"m..050 kg 0. The correct use of the female and male parts has to be taken into consideration. thread f.68 kg 0..009 kg 0. while the female part always has to be swivelling.. 2 1/2" m.18 kg 0.. thread f. female Round Thread (certified B.. thread m.22 kg 0. thread f. Spring-loaded plungers in the female part grip in the gap of the male part..19 kg 0. 2 1/2" f. for Storz couplings 276780 276740 276750 276760 276770 276790 276795 276798 Storz 38 Storz D Storz C Storz B Storz A Storz 65 Storz 125 Storz 150 1 1/2" 1" 2" 3" 4" 2 1/2" 5" 6" 0.18 kg 5 244389 244390 BS. 1 1/4" 1 1/2" 2" 1 1/2" 2" 1 1/2" 2" 2 1/2" 1 1/2" 2" 2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 4" 4 1/2" 5" f.light alloy Made of aluminium alloy... thread m. consisting of a male and female part. 2 1/2" m. British Instantaneous as to BS 336:1989) 244387 ... thread f. thread m. 2 1/2" m.009 kg 0. 1 1/2" f. .. Inst. Inst. Inst.20 kg 0. per unit 256972 256970 256966 256978 256967 256965 256969 256976 256986 256980 256983 256988 256987 B.60 kg 0.75 kg 244450 Blank caps with chain. certified as to EN 1982.95 kg 0... Inst. per unit 268888 268886 268885 268891 256911 277270 277272 B. – BS 336 2 1/2" m. male 336:1989 f . – BS 336 2 1/2" f. made of light alloy.. 1 1/2" male B.. per pair 244454 244458 244456 244456 B. thread f... serrated 38 x 85 mm 63 x 60 mm 0.30 kg 0. 1 1/2" male B..35 kg 1.60 kg 1.65 kg 0..95 kg 0. Washers made of Nitrile rubber.10 kg 244392 244388 pLEASE nOTE: BS. 1 1/2" male BS 336 2 1/2" female B. thread f. 1 1/2" BS 336 2 1/2" BS 336 2 1/2" 38 x 85 mm.....65 kg 0. – BS 336 2 1/2" m. – 1 1/4" 1 1/2" 2" 2" 1 1/2" 2" 2" 2 1/2" 2 1/2" 1 1/2" 2" 2 1/2" 2 1/2" 1 /2" 1 /2" 2 1/2" 5" f. 1 1/2" female BS 336 2 1/2" female BS 336 2 1/2" male BSRT 4" male BSRT 4" female BSRT 4” female BSRT 4” female BSRT 5 1/2" female 2 1/2" male 2 1/2" female 2 1/2" male 2 1/2" male 1 1/2" male 2 1/2"” female 2 1/2" female 2 1/2" male 4" male 2 1/2" male 4” female 5 1/2" male 4" male 0. 1 1/2" female B. – B.70 kg 268885 268891 Adapters. – BS 336 2 1/2" f..55 kg 1. Inst..85 kg 0.55 kg 1...05 kg 1. Inst..89 kg 0.68 kg 0.. – B. thread m. 1 1/2" male BS 336 2 1/2" female BS 336 2 1/2" male BSRT 3" female BSRT 4" female BSRT 5 1/2" female 38 mm 38 mm 63 mm 63 mm 75 mm 102 mm 140 mm 0... thread f. 1 1/2" f. per pair 244449 244450 234510 BSRT 3" BSRT 4" BSRT 5 1/2" 75 mm 100 mm 140 mm 2. thread f. 1 1/2" f. thread f.. Coupling certified as to BS 336:1989 and non-standardised 1.60 kg 1. Inst. – BS 336 2 1/2" f.70 kg 0.60 kg 0. thread m. – BSRT 4" f....80 kg 0. Working pressure 15 bar.10 kg 2..49 kg 0..85 kg 0. – B.. female BSRT . thread f.. Inst. British Instantaneous Round Thread (certified as to BS 336:1989) ...80 kg 4. thread f.. Inst. – BSRT 5 1/2" m.18 kg 0. 1 1/2" female B.80 kg 0.10 kg 1.11 kg 0.50 kg 1.22 kg 0. – BS 336 2 1/2" m. British Standard m.. thread f.5” instantaneous couplings. thread m.98 kg Suction hose couplings.. Inst.. – BS 336 2 1/2" f. 1 1/2"" f. EN 12420 or EN 12449.65 kg 3. per unit 277223 277224 244382 277209 27722801 244386 24439005 244388 244391 277217 277216 277215 244392 244398 244399 256981 244395 B.. Inst. thread f.. thread 0. instantaneous to instantaneous and BSRT. 256976 Adapters. 1 1/2" m. thread f.. thread m. – BS 336 2 1/2" m.50 kg 5 277270 Other sizes upon request. Inst. thread f. British Standard B.90 kg 1.. thread f.80 kg 0.25 kg 0.. 256969 British Coupling System ..41 kg 0.154 Delivery hose couplings.40 kg 0. – BS 336 2 1/2" f..95 kg 0. – BSRT 3" m.. Inst.51 kg 0. – BSRT 4" m.10 kg 1.gunmetal Made of gunmetal. serrated 38 x 85 mm 63 x 60 mm 1. male f .05 kg 0.80 kg 100 mm 8.10 kg 2... – B.1 kg 0. BS 336 2 1/2" m.50 kg 0. 1 1/2" BS 336 2 1/2" BS 336 2 1/2" 38 x 85 mm. Inst..42 kg 0. per unit 25697804 25697806 25697807 25697805 25697808 BS 336 – B. 1 1/2" female B. – BS 336 2 1/2" f.. British Instantaneous British Standard 336:1989 British Standard Round Thread (certified as to BS 336:1989) 25697805 .90 kg 244451 277261 Coupling adapters.70 kg 2. 2.80 kg 155 Suction hose couplings.9 kg 5 Washers for delivery and suction hose couplings. Inst...38 kg 2.. Inst.... per pair 277110 277116 277117 B.30 kg 244482 pLEASE nOTE: BS.... nOzzLES Couplings and Fittings Delivery hose couplings. 2 1/2" f. FITTInGS. 1 1/2" female BS 336 2 1/2" female BS 336 2 1/2"" male BSRT 3" female BSRT 4" female BSRT 5 1/2" female 38 mm 38 mm 63 mm 63 mm 75 mm 102 mm 140 mm 0..80 kg 0. per pair 244448 244451 234512 BSRT 3" BSRT 4" BSRT 5 1/2" 75 mm 6..FIRE HOSES.50 kg 140 mm 15. per unit 256979 256977 BS 336 2 1/2"" f.30 kg 1... – B.03 kg 0.30 kg 277117 Blank caps with chain. Inst..07 kg 256979 Adapters Instantaneous or BSRT to Storz System. Inst.67 kg 1. Inst.. B. per unit 244480 244482 244485 244486 244488 244489 B. 2 1/2" m. 2 1/2" m. Inst. – BS 336 2 1/2" m. COupLInGS. 2 1/2" f. female BSRT .... – BSRT 4" f...... Inst....05 kg 0.01 kg 0. Inst.01 kg 0.. m...85 kg 0.10 kg 3...06 kg 0... 1 1/2" BS 336 2 1/2" BSRT 3" BSRT 4" BSRT 5" BSRT 5 1/2" 38 mm 63 mm 75 mm 102 mm 125 mm 140 mm 0. made of light-alloy. per unit 277257 277256 277265 277261 277269 277271 277273 B.30 kg 5. swivel – Storz 52=C 65 75=B 75=B 110=A 0...... – B..75 kg 2.. 30 kg 0.35 kg 1.. Washers made of Nitrile rubber..50 kg 0...00 kg 1.60 kg 3..10 kg 4.gunmetal Made of gunmetal.. m.00 kg 2... Delivery hose couplings 279323 278705 278706 NH 1 1/2" NH 2 1/2" NH 2 1/2" 38 x 85 mm 63 x 50 mm 63 x 50 mm 1...10 kg Blank caps with chain 278863 278861 278862 278881 278883 278882 278884 278885 278861 278862 American Standard nH Couplings System ..30 kg NH 1 1/2" female NH 2 1/2" female NH 2 1/2" male NH 4" female NH 4" male NH 4 1/2" female NH 5" female NH 6" female 38 mm 63 mm 63 mm 102 mm 102 mm 114 mm 127 mm 152 mm 0.... male f . British Instantaneous British Standard 336:1989 British Standard Round Thread (certified as to BS 336:1989) .....35 kg 1. Couplings certified as to NH (NFPA 1963).00 kg 1... B.. Washers made of Nitrile rubber..00 kg 278720 Suction hose couplings 278771 278772 278773 NH 4" NH 4 1/2" NH 5" 100 x 170 mm 110 x 170 mm 125 x 220 mm 2.80 kg 1.80 kg 4.35 kg 0..00 kg 5 Suction hose couplings 278770 278767 278765 NH 4" NH 4 1/2" NH 5" 110 x 170 mm 110 x 170 mm 125 x 220 mm 9.50 kg 0. Inst....... female BSRT .20 kg 1.40 kg 12. Delivery hose couplings 278710 278720 278721 278722 NH 1 1/2" NH 2 1/2" NH 2 1/2" NH 2 1/2" 52 x 50 mm 75 x 60 mm 75 x 100 mm 63 x 80 mm 0..00 kg 2.....156 AMERICAn STAnDARD nH COupLInGS SYSTEM American Standard nH Couplings System – light alloy Made of aluminium alloy. NH 2 1/2" female NH 2 1/2" male NH 4" female NH 5” female 38 mm 38 mm 63 mm 63 mm 102 mm 125 mm 0.90 kg 278880 pLEASE nOTE: BS. Couplings certified as to NH (NFPA 1963).20 kg 2...30 kg 10..50 kg Blank caps with chain 278705 279311 278865 278860 278864 278880 278886 NH 1 1/2" female NH 1 1/2" male.... Working pressure: 16 bar...30 kg 0..00 kg 1. Working pressure: 16 bar.10 kg 0.. . COupLInGS. thread 2" m..80 kg 0. British Instantaneous British Standard 336:1989 British Standard Round Thread (certified as to BS 336:1989) . thread 2 1/2" f.33 kg 0. nOzzLES Couplings and Fittings Adapters nH thread to pipe thread DIn ISO 228 Made of light-alloy 278803 278807 278806 278808 278923 278809 278832 278837 278835 278836 278838 278840 NH 1 1/2" f. thread 2 1/2" f.nH Swivel Special Adapters made of light alloy 278950 278951 278952 278953 278954 278955 278956 278957 25697803 Storz 65 – Storz B – Storz A – Storz A – Storz A – Storz A – Storz 125 – Storz 125 – BS 336 2 1/2"f.. NH 5" f. NH 2 1/2" f.. – NH 1 1/2" f. – NH 1 1/2" m. – NH 4" f.2 kg 278950 Swivel coupling adapters nH thread – nH thread made of light alloy 278922 278925 278926 278924 NH 2 1/2" f.. FITTInGS. NH 4" f. – NH 2 1/2" f..30 kg 1.22 kg 0. m. thread 6" f.. NH 2 1/2" f. – NH 2 1/2" m. thread 4 1/2" f. thread 4 1/2" f...2 kg 3.30 kg 0.....75 kg 0. female BSRT ... thread 2" f.70 kg 279320 278811 Other sizes upon request Adapters STORz . B. – NH 2 1/2" f.2 kg 2. thread 2 1/2" f. – NH 5" m. – NH 4" f..80 kg 0.. 0..30 kg 0...35 kg 0. – 1 1/2" 2" 2" 2" 2 1/2" 2 1/2" 4" female thread female thread female thread female thread female thread female thread female thread 0. – NH 1 1/2" m.13 kg 0.60 kg 0.. NH 2 1/2" m.. – NH 2 1/2" f..90 kg 1.30 kg 278957 5 Other sizes and materials upon request. 278922 pLEASE nOTE: BS. – NH 4" m...00 kg 157 278808 278809 278923 Swivel adapters nH thread to pipe thread DIn ISO 228 Made of light-alloy 279320 279321 278805 278812 278811 278810 278830 NH 1 1/2" f.95 kg 0....9 kg 1.8 kg 3...7 kg 0. Inst. – NH 4 1/2" m. – NH 2 1/2" f.60 kg 0.60 kg 0... – NH 1 1/2" f.. NH 2 1/2" m. – NH 6" m. – NH 4" m. thread 5" f. male f .25 kg 0.50 kg 0. – NH 2 1/2" m.FIRE HOSES. thread 4 1/2" f.. – 1 1/2" f.. NH 1 1/2" f. – NH 2 1/2" f.20 kg 0. NH 5" f...25 kg 0. NH 2 1/2" f. thread 0.. NH 2 1/2" f... NH 6" f. – NH 2 1/2" f. with handle NH 4 1/2" f.32 kg 0.... – NH 2 1/2" m. 0.. – NH 2 1/2" m.3 kg 2. thread 4" m.5 kg 2.5 kg 1. • 1 1/2" f. – 3 x 2 1/2" f. Dividing breeching screw down type Made of light-alloy Storz System 257000 Storz B – CBC 257500 Storz B – CC 257600 Storz A – BB 257700 Storz 65 – 38/38 257705 Storz 65 – 38/65/38 British Standard System 256961 BS 2 1/2" m. 256958 American nH (national Hose) System (Leader line wye) 278970 NH 2 1/2" f. 279455 279455 . 25695803 BS 2 1/2" m.20 kg 4.1 kg. Inlet 5" female. 256961 BS 2 1/2" m. 258000 6.40 kg 25695804 American Standard System: wye valves Strong lightweight aluminium construction Self-locking handle for positive positioning Male adapters are easily removed for adjustment of seats Used for laying lines from hydrant to the pumper or branching off a 2 1/2" or larger line to three 2 1/2" lines Body painted red 279450 279451 279452 279453 279454 Inlet 2 1⁄2" female.20 kg 3. – 3 x 2 1/2" f.40 kg 3. made of light-alloy 258000 Storz B – CBC 258300 Storz A – BBB 258600 Storz A – BB 258500 Storz B – CC 258001 Storz 65 – 38/65/38 258710 Storz 65 – 38/38 British Standard System 25695801 BS 2 1/2" m.• 2 1/2" f. Inlet 3" female.15 kg 4.• 1 x 2 1/2" m.00 kg 4. – 1 1/2" f. Weight: 6. Weight: 5.158 DIVIDInG BREECHInGS are used to split up a single line into two or three lines.2 kg.30 kg 3. Inlet 3 1/2" female.9 kg. – 2 x 1 1/2" m.60 kg 5. Outlet 3 x 2 1/2" male couplings. 256957 BS 2 1/2" m. Weight: 6. ball type valves Storz System. Inlet 4 1/2" female. 256958 BS 2 1/2" m. Weight: 6. Outlet 3 x 2 1/2" male couplings.7 kg.70 kg 5.90 kg 9. 3. 25695804 BI 2 1/2" m – 3 x 2 1/2"f. Outlet 3 x 2 1/2" male couplings.70 kg 3. – 2 x 1 1/2" m.• 2 1/2" f.00 kg 257000 5. Weight: 6.80 kg 4.10 kg 6.6 kg.• 1 1/2" f. – 2 x 2 1/2" f. – 2 x 1/2" f.10 kg 5.00 kg 5.00 kg 3. – 1 1/2" f. 278971 NH 2 1/2" f. Outlet 3 x 2 1/2" male couplings. Outlet 3 x 2 1/2" male couplings. Outlet 3 x 2 1/2" male couplings.20 kg 5. Weight: 6. Inlet 4" female.00 kg 6. – 2 x 2 1/2" f. 256956 BS 2 1/2" m.30 kg 2.40 kg 5 Dividing breeching.8 kg. nOzzLES Couplings and Fittings 3-Way Suction "Siamese” Strong lightweight aluminium construction. BSRT 4" female swivel – 3 x 2 1/2" male inst.3 kg.00 kg 9.3 kg. angled type. Weight: 2 kg. made of light alloy. Weight: 5.90 kg Weight: 6. three or four water feeds into one feed. 259000 259100 259400 259515 259200 259500 259525 259001 259452 Storz B – CC Storz A – BB Storz A – BBB Storz A – 65/65 Storz 150 – AA Storz 125 – BBBB Storz 125 – 2 x A Storz 65 – 38/38 Storz 125 – 3 x BS 2 1/2" m. Outlet 2 x 1 1/2" male couplings. Weight: 7.7 kg.20 kg 11. Inlet 3 x 2 1/2" female. angled type. made of light alloy. Weight: 6.00 kg 279304 5 279305 BS System.FIRE HOSES..10 kg Weight: 6. Made of light alloy. Weight: 4.2 kg.40 kg Weight: 6. 259100 259551 Collecting breechings made of gunmetal upon request. Inlet 3 x 2 1/2" female. Inlet 2 1/2" female. BSRT 4" female swivel – 2 x 2 1/2" male inst. Weight: 10.10 kg 3. angled type. COLLECTInG BREECHInGS are used to combine two. 279079 . BSRT 5 1/2" female swivel – 2 x 2 1/2" male inst. BSRT 5 1/2" female swivel – 3 x 2 1/2" male inst. – 2 x 2 1/2" f. COupLInGS.60 kg 159 279600 Leader Line Wye Valves 279304 279305 Inlet 2 1/2" female.. Weight: 1.. Weight: 2.3 kg.50 kg 2. Storz System. Outlet 5" female.60 kg 10. Outlet 2 x 2 1/2" male couplings. 2. angled type.00 kg 10. body painted red Self-locking handle for positive positioning 2 1/2" swivel inlets for positive positioning Used for pumper suction or aerial platform inlets 279600 279610 279620 279630 Inlet 3 x 2 1/2" female. Inlet 3 x 2 1/2" female. Outlet 3" female. angled type. Radial types and further in-line types upon request. Outlet 4 1/2" female. BSRT 5 1/2" female swivel – 4 x 2 1/2" male inst.40 kg 7. FITTInGS. 279079 NH 4" f.8 kg. Outlet 4" female. as per DIn 14355. 259553 259551 259594 277493 277494 277490 BS 2 1/2" female swivel – 2 x 2 1/2" male inst. All inlets clappered.00 kg 3.. Weight: 8.4 kg. Weight: 3 kg.. American nH System. light alloy 5. Weight: 3.3 kg 5. 260215 BSRT 5 1/2" f.0 kg 8.5 kg. 2 1/2" male.0 kg 2. light alloy light alloy light alloy 3. STRAInERS / BASKETS 279307 Suction strainer with non-return valve Strainers prevent obstructions in the suction line caused by entry of stones. Oblique outlet permits better guiding of hoses through cellar windows.50 kg 260900 . double clappers. light alloy 5. 2 x 2 1/2" female.50 kg 5.160 279307 Valved Wye: Clapper Siamese Strong lightweight aluminium construction. light alloy 279125 NH 5" f.1 kg 9. Used for joining two liners into one.50 kg System British Standard 260110 BSRT 3" f. NH.0 kg 12. optional drain valve.0 kg 5. Made of gunmetal or aluminium alloy.5 kg 2. 260900 260910 Storz A light alloy BSRT 4" f. 260210 BSRT 4" f.9 kg 260210 Low level strainer with non-return clapper This design allows draw-off almost down to the ground and provides good stability. Suction strainers with drain arrangement and non-return valve. 5 260200 System Storz 260000 Storz C light alloy (DIN 14362) 260100 Storz B ight alloy (DIN 14362) 260200 Storz A light alloy (DIN 14362) 260300 Storz A with handles light alloy 260350 Storz 65 light alloy 260400 Storz 125 light alloy 260500 Storz 150 light alloy 1.2 kg 8.0 kg System nH (American) Standard 279121 NH 4" f. small pieces of wood and other debris. Body painted red. Collecting breechings made of gunmetal upon request.0 kg 2. 8 kg 275640 .4 kg 5 275562 21150409 Swimmer for suction strainer Weight: 2.1 kg 9. 279310 NH 4" f.3 kg 4.FIRE HOSES.8 kg 9. nOzzLES Couplings and Fittings Cylindrical Suction Strainer without non-return valve System British Standard 260549 BSRT 3" f. COupLInGS. 275560 3" Wicker Basket 0. FITTInGS. gunmetal gunmetal gunmetal gunmetal 4.7 kg 275620 3" Wire Mesh Basket 1.9 kg System nH (American Standard) 279309 NH 2 1/2" f. 279120 NH 4" f. 27912501 NH 6" f. prevents even very small object from entering suction line.0 kg 275640 4" Wire Mesh Basket 1. 260550 BSRT 4" f. 275600 2" Wire Mesh Basket 0. prevents even very small objects from entering suction line. 21150409 Wire mesh basket Offers together with Suction Strainer maximum protection.5 kg 275680 6" Wire Mesh Basket 1.1 kg 275564 5 1/2" Wicker Basket 1.1 kg 7.6 kg 7.3 kg 275660 5" Wire Mesh Basket 1. 260565 BSRT 4" f.8 kg 260550 260555 Wicker basket Offers maximum protection.5 kg 6. 260566 BSRT 5 1/2" f.9 kg 275562 4" Wicker Basket 1.5 kg. 161 gunmetal gunmetal light alloy gunmetal light alloy 4. 260555 BSRT 5 1/2" f.4 kg 6. shafts. Working head of the bilge pump: 8 metres water column (0. for pumping out of liquids in basements. it can also easily be put into tanker vehicles through manholes.4 kg. Made of stainless steel with Storz B couplings (3"). Output up to 800 l/min.3 kg.outlet with NH 2 1/2" male coupling. Weight: 8 kg. The reverse flow preventer with non-return valve mounted between can avoid this.200 l/min. Weight: 14. depending on the hydrant pressure available. Inlet with BS 2 1/2" male – outlet with BS 2 1/2" female coupling. Comes with check valve. 934000 with Storz B couplings (3"). with BS 2 1/2" couplings male and female. The unit is made of corrosion resistant light alloy.162 Rosenbauer Ejector pump Safety type ejector pump. Weight: 7. basements.5 kg. pits. Inlet with Storz 38 coupling – outlet with Storz 65 coupling. Bilge Turbo pump Suitable for emptying bilges. 268300 5 267100 Reverse Flow preventer To prevent the contamination of the drinking water supply the line feeding the ejector pump may not be connected to the hydrant standpipe directly. Weight: 8 kg. Inlet with NH 1 1/2" female . 934010 268300 934020 934030 934100 934000 . by means of 2 lifting eyes. with NH 2 1/2" couplings male and female. Thanks to its small dimensions. bilges etc. ducts and pits. Inlet with BS 1 1/2" male – outlet with BS 2 1/2" female coupling. Weight: 7. Weight: 35. with Storz 65 couplings (2 1/2"). 267100 267101 267211 267212 267311 Inlet with Storz C coupling – outlet with Storz B coupling. The incorporated breather aerates the pressure line in case the pressure drops at the main.9 kg.8 bar). Weight: 14. with a working pressure of 10 bar at the turbine pump. Decanting capacity approx. Weight: 14.5 kg. Weight: 8 kg. 1. A closed circuit water turbine acts as driving engine.1 kg. Weight: 14. Weight: 8 kg.9 kg. 275530 5 275530 Coupling spanner Storz 125/135/150 Made of malleable cast iron. 269600 269590 . painted black.57 kg. 275525 275525 Coupling spanner H (Storz 32 and Storz 38) Made of steel. COupLInGS.FIRE HOSES. Weight: 0. C and 65 mm couplings.5 kg. Comes with cold resisting handgrip. Suitable for Storz A. Weight: 0.3 kg. 275400 275510 Coupling spanner BC Made of steel. 019061-001 Coupling spanner BSRT 3" . B. C and Storz-65 couplings.6" Weight: 0.26 kg. 019061-001 279210 Coupling spanner nH 1" . galvanised.2 kg. FITTInGS. the other end acts as a spanner for Storz A. One end serves to open and close hydrant valves. nOzzLES Couplings and Fittings SpAnnERS 275400 Coupling spanner ABC Made of steel. 279210 269590 pillar hydrant wrench with ratchet Made of light alloy. Weight: 1. B. Weight: 0. hot dip galvanised.28 kg. Conforms with DIN 3223. 275510 275511 Coupling spanner Storz 65 . painted black.66 kg.3 kg. painted black.38 Made of malleable cast iron. as per DIN 14822. Weight: 0. 269600 Spanner for pillar type hydrant Made of forged steel.7 kg.5 1/2" Made of steel. 163 275505 Coupling spanner ABC Made of light alloy. Weight: 2. Weight: 0. Weight: 3. Weight: 0.24 kg. 9 kg. Weight: 2.30 kg Weight: 1. with BS 2 1/2" male.30 kg Weight: 1. Weight: 1. With NH 1 1/2" female.20 kg Weight: 2.90 kg Weight: 1.164 MuLTIpuRpOSE BRAnCH pIpES 262020 Euro nozzle Flow rate and throw distance conform to EN 671. With Inst.6 kg. Special control for water curtain for maximum protection of the fireman. with Inst. full jet and spray.60 kg Weight: 1. 1 1/2" male. 5 262100 262100 262105 262112 262110 262107 262170 with Storz C. 1 1/2" male. full jet and spray. made of light alloy. With Storz 65.50 kg Multi-purpose branch pipe size BM In full conformity with DIN 14365 and ÖNORM F-2190. Comes with 9 mm nozzle tip.85 kg Weight: 2.60 kg Weight: 1. With Storz 38.20 kg.70 kg Weight: 2.90 kg Multi-purpose branch pipe size CMM Comes with nozzle tip 9 mm. 262020 262000 Multi-purpose branch pipe size DM In full conformity with DIN 14365 and ÖNORM F-2190. Weight: 1. full jet and spray. With Storz 65.40 kg Weight: 1. full jet and spray. Weight: 2. with Storz 65. Comes with 16 mm nozzle tip. Infinetely variable by turning the head clockwise from shut-off to spray to 90° to full jet. Weight: 1. Weight: 0. Provided with Storz-D (1") coupling. 263000 263015 263017 263010 263012 279172 263000 With Storz C. with Storz 38. The branch pipe valve allows for 3 positions: stop. Provided with Storz 25 coupling. Multi-purpose branch pipe CM Certified with DIN 14365 and Austrian Standard ÖNORM F 2190. 262200 262202 262206 279159 With Storz B. Weight: 0. With BS 2 1/2" male. Made of light alloy.00 kg Weight: 1. With NH 2 1/2" female.40 kg Weight: 1. made of light alloy.5 kg. Comes with 4 mm nozzle tip. with NH 1 1/2" female.00 kg . The branch pipe valve allows for 3 positions: stop. Length: 300 mm.30 kg Weight: 1.85 kg Weight: 1. made of light alloy. The branch pipe valve allows for 3 positions: shut-off. The branch pipe valve allows for 3 positions: stop. With BS 2 1/2" male. 16 mm.0 1.7 14.0 Average Throw Width m 1. 4 mm.5 1. nOzzLES nozzles Multi-purpose water curtain branch pipe BMM Comes with nozzle tip 16 mm.40 kg.7 1. COupLInGS.04 kg.6 8.FIRE HOSES.1 1. 165 nozzle Tips 261700 DM nozzle tip 1 /4" thread.3 2. FITTInGS.4 10. 24 53 120 215 270 365 380 715 620 955 Straight Stream Throw Distance m 14 16 24 26 24 26 29 34 29 34 Fog Stream Average Throw Distance m 7.0 12. Weight: 0.7 2.0 11. Multipurpose Branchpipe Size DM CM CMM* BM BMM* w/ nozzle mm 4 – 9 – 9 – 16 – 16 – w/o nozzle mm – 6 – 12 – 12 – 22 – 22 Waterflow at 5 bar Straight Stream l/min.5 1.5 2.05 kg. Weight: 0.05 kg. 24 53 120 215 270 365 380 715 620 955 Fog Stream l/min. 262204 With Storz 65. full jet and spray. Weight: 0.0 10.70 kg. 261900 BM nozzle tip 11/2" thread. The branch pipe valve allows for 3 positions: stop. Weight: 2. 20 mm.3 2. 263100 With Storz B.90 kg. 279160 With NH 2 1/2" female. Weight: 3. Special control for water curtain for maximum protection of the fireman. 4 mm. 5 261912 BM nozzle tip 1 1/2" thread. Weight: 2. Weight: 1.09 kg. 261800 CM nozzle tip 1" thread. Tip Inner Diam.5 * if watercurtain is opened .0 12. Weight: 0.0 11. 263110 With BS 2 1/2" male.7 14.00 kg. maximum protection • Durable. water carrying components corrosion-resistant materials (brass. The Flash-over position at 45° (Pointer at 12 o’clock position) is easy to detect. 1) Spinning teeth made of stainless steel: for superb fog pattern when using "water curtain"-setting. 2) Stream adjustment: within 100° rotation adjustment from straight stream to fog pattern. ergonomic on/off handle: glass-fibre reinforced and additionally light alloy reinforcement on both sides.166 nOzzLES Selectable Gallonage nozzles • High performance. light-weight construction • Ergonomic design SelectFlow "En” nozzles The new line of ROSENBAUER Select Flow Nozzles Type "EN" is certified as to DIN 14367:2002 and in accordance with EN 15182:2007 for an operating pressure of 6 bar. . 3) Ergonomic pistol grip: for better handling and reduced fatigue. 6) High-quality materials: Body hard anodised light alloy. stainless steel and man-made materials). 5) Rugged. 5 1 2 3 4 5 6 4) Shock-resistant pattern adjustment bumper: with integrated pointer. even wearing fire-fighting gloves. 1 kg Adjustable flow settings in l / min * Max. COupLInGS.FIRE HOSES. fume abatement and combating solvent fires Water curtain • Finest water droplets and wide spray angle to create a large area water shield • Maximum protection against radiant heat . nOzzLES nozzles Technical Data: 167 Type RB 99 En SelectFlow 17 30 80 130 32 m 28 cm 2 kg RB 100 En SelectFlow 45 85 130 200 36 m 28 cm 2 kg RB 101 En SelectFlow 130 230 300 400 44 m 28 cm 2. FITTInGS. “RB 100 EN” and “RB 101 EN” are measured with reference to an operation pressure of 6 bar. Straight stream • Working from a safe distance with extensive throw range • High kinetic energy to eliminate ember and fire pockets 5 Variable fog patterns • Fine water droplets for rapid heat reduction • Minimisation of water damage due to smaller volumes of water • ideal for cooling. stream reach * Length (without coupling) Weight (without coupling) * The flow settings and the stream reach for the types SelectFlow “RB 99 EN”. inst. Other coupling systems are available on request. SelectFlow Model “RB 99 En” 279500 279505 279513 279510 279517 279520 279522 279525 without coupling / BSP 1" female without coupling / BSP 1 1/2" female with coupling Storz 38 with coupling Storz C with coupling Storz 65 with coupling instantaneous 1 1/2" male with coupling BS 2 1/2" male with coupling NH 1 1/2" female Storz C 5 SelectFlow Model “RB 100 En” 279530 279535 279543 279540 279547 279550 279555 279557 B.1 1/2" or BS 2 1/2" male without coupling / BSP 1" female without coupling / BSP 1 1/2" female with coupling Storz 38 with coupling Storz C with coupling Storz 65 with coupling instantaneous 1 1/2" male with coupling BS 2 1/2" male with coupling NH 1 1/2" female SelectFlow Model “RB 101 En” 279560 279565 279573 279570 279577 279580 279585 279590 without coupling / BSP 1" female without coupling / BSP 1 1/2" female with coupling Storz 38 with coupling Storz C with coupling Storz 65 with coupling instantaneous 1 1/2" male with coupling BS 2 1/2" male with coupling NH 1 1/2" female nH 1 1/2" female .168 All nozzles are available either without couplings (female thread BSP) or individually fitted with Storz. British Standard or NH-couplings. It permits multiple flow setting using a selection control ring with detents. “RB 101 NFPA” and “RB 102 NFPA” are shown with reference to an operation pressure of 7 bar.9 kg 57 m 25 cm 3. ** with full jet *** with combined jet . stream reach * Length (without coupling) Weight (without coupling) 47 m 23 cm 1. COupLInGS.5 bar.FIRE HOSES. “RB 100 NFPA”. 169 5 3 4 5 2 1 6 (1) Moulded bumper ring in front of the nozzle for various jet patterns (2) Special formed pistol grip (3) Horseshoe type valve control handle (4) Swivel inlet (5) Flow selection control ring with detents (6 Spinning teeth for very fine fog pattern made of stainless steel Technical Data: Type Adjustable flow settings in l / min * RB 99 nFpA SelectFlow 19 37 90 150 39 m 20 cm 1.9 kg RB 102 nFpA SelectFlow 360 475 550 750 57 m 25 cm 3. The ProJet nozzle provides a combination stream: straight stream and fog together.5 kg RB 101 nFpA SelectFlow 115 230 360 475 47 m 23 cm 1.2 kg * The flow settings and the stream reach for the types SelectFlow “RB 99 NFPA”. “ProJet I” and “ProJet II” with reference to an operation pressure of 3.5 kg RB 100 nFpA SelectFlow 50 100 150 230 40 m 20cm 1. FITTInGS.1 kg proJet I 190** 420*** proJet II 440** 790*** Max. nOzzLES nozzles SelectFlow and proJet nozzles “nFpA” The ROSENBAUER SelectFlow nozzle Type “NFPA” conforms to all aspects of NFPA 1964:2008. This combination stream allows attack by the fire fighting teams and an extremely effective extinguishing capacity. SelectFlow Model "RB 99 nFpA" 279239 without coupling / BSP 1" female 279240 without coupling / BSP 1 1/2" female 279245 with coupling Storz C 279246 with coupling Storz 65 279247 with coupling instantaneous 1 1/2" male 27924705 with coupling BS 2 1/2" male 279248 with coupling NH 1 1/2" female Combination stream .170 Straight stream • Working from a safe distance with extensive throw range • High kinetic energy to eliminate ember and fire pockets Straight stream Variable fog patterns • Fine water droplets for rapid heat reduction • Minimisation of water damage due to smaller volumes of water • Ideal for cooling. British Standard or NH-couplings. Other coupling systems are available on request. fume abatement and combating solvent fires 5 Variable fog patterns Water curtain • Finest water droplets and wide spray angle to create a large area water shield • Maximum protection against radiant heat Water curtain All nozzles can be supplied either without couplings (female thread BSP) or individually fitted with Storz. COupLInGS. FITTInGS.FIRE HOSES. nOzzLES nozzles SelectFlow Model “RB 100 nFpA” 27922802 279234 279229 27922906 27922805 27922807 27922804 without coupling / BSP 1" female without coupling / BSP 1 1/2" female with coupling Storz C with coupling Storz 65 with coupling instantaneous 1 1/2" male with coupling BS 2 1/2" male with coupling NH 1 1/2" female 171 SlectFlow Model "RB 101 nFpA” 27923008 27923004 27923005 27923006 279230 27923002 27923003 without coupling / BSP 1" female without coupling / BSP 1 1/2" female with coupling Storz C with coupling Storz 65 with coupling instantaneous 1 1/2" male with coupling BS 2 1/2" male with coupling NH 1 1/2" female Storz C 5 SelectFlwo Model "RB 102 nFpA” 279233 27923307 27923302 27923304 27923301 27923305 without coupling / BSP 1 1/2" female without coupling / BSP 2 1/2" female with coupling Storz B with coupling Storz 65 with coupling BS 2 1/2" male with coupling NH 2 1/2" female B.1 1/2" or BS 2 1/2" male proJet Model "I” 279215 279216 279217 279218 279219 without coupling / BSP 1 1/2" female without coupling / BSP 2 1/2" female with coupling Storz C with coupling BS 2 1/2" male with coupling NH 2 1/2" female proJet Model "II” 279220 279221 279222 279223 279224 without coupling / BSP 1 1/2" female without coupling / BSP 2 1/2" female with coupling Storz B with coupling BS 2 1/2" male with coupling NH 2 1/2" female nH 1 1/2" female . Inst. screw drivers. wrench. pliers. punches.172 Recommended Accessories for nozzles SelectFlow and proJet: Quick Clamp On Foam Tube expansion rate up to 14:1 279236 for SelectFlow models “RB 99 EN”. spanner. . Weight: 4 kg. “RB 100 EN” and “RB 100 NFPA” for SelectFlow models “RB 101 NFPA” and „ProJet model “I” for SelectFlow models “RB 101 EN” for SelectFlow “RB 102 NFPA” and ProJet “II” 279231 27923101 279237 Spare part Set 27923501 27923401 27923001 27923306 279225 279226 for SelectFlow models “RB 99 EN” and “RB 99 NFPA” for SelectFlow models “RB 100 EN” and “RB 100 NFPA” for SelectFlow models “RB 101 EN” and “RB 101 NFPA” for SelectFlow “RB 102 NFPA” for ProJet “I” for ProJet “II” 5 279588 nozzle repair tool kit for all nozzles “SelectFlow” and “proJet” Consists of: hammer. O-rings. hex wrenches. “RB 99 NFPA”. 15 kg. FITTInGS. • Combination of fog and straight stream. 279270 279271 279272 279273 BSP 2 1 1/2" female Storz B BS 336 2 1/2" male NH 2 1/2" female 279260 5 Select flow nozzle with play pipe • • • • • • • • • • • Strong lightweight aluminium construction Play pipe with solid compact design for better balance Easy grip vinyl coated handle Constant selectable gallonage . • Flush without shutting down.65 kg. • The slide-type valve allows the operator to control the flow without effecting the stream quality.FIRE HOSES. 173 Flow rate 40-475 l/min (at 7 bar) Weight: 1.55 kg. • Volume controlled by 6 positions of handle including the shutoff. • Automatically adjust to changes in flow and pressure. 279296 279297 279298 279299 BSP 2 1/2" female Storz B BS 336 2 1/2" male NH 2 1/2" female 279296 . nOzzLES nozzles Automatic nozzles • Strong lightweight aluminium construction. • Pattern detents for positive pattern positioning. 279260 279261 279262 279263 BSP 1 1/2" female Storz C BS 336 2 1/2" male NH 1 1/2" female Flow rate 265-750 l/min Weight: 2.flow remains constant in all patterns Change flow without changing pattern and flush without shutting down Multiple pattern detents for positive pattern positioning Tight straight stream and 110° wide dense fog pattern Quality stream performance even at low pressure Replaceable spinning teeth made of stainless steel Excellent for use with inline inductor and foam making branch pipes Certified as to NFPA 1964 standard Flow rate 360-475-550-750-950 l/min (at 7 bar) Weight: 4. COupLInGS. • Tough. It is designed to discharge water / AFFF solution and dry chemical powder. Side by side horseshoe type valve handles allow Water / AFFF or dry chemical powder to be discharged either separately or simultaneously. 2. storage facilities and more.55 kg. Change of flow or flush is possible without shutting down. 279280 Flow rate 115-230-360-475 l/min Weight: 4 kg.5 kg per second. corrosion-resistant design for harsh industrial and marine environment. chemical plants. • Weight: 4 kg. 90. narrow or wide angle fog allowing for man protection water curtain. • Heavy-duty spinning teeth made of stainless steel for powerful fog pattern. • Ideal for use with foam inductors and foam making branch pipes. offshore platforms. A moulded bumper ring in front of the nozzle can easily be turned to produce straight stream. For water / AFFF operation.5 kg. 150 and 230 l/min or flush (all flow figures refer to a nozzle pressure of 7 bar). Dry chemical powder operation: output between 1.5" BSP connections. 279255 . 279286 279287 279288 279289 BSP 2 1/2" female Storz B BS 336 2 1/2" male NH 2 1/2" female 279286 279255 Dual agent handline nozzle Made of hard anodised light alloy. Comes with 2 female 1. • Suitable for refineries. Weight approx.174 Industrial nozzle • Brass construction. 279280 279281 279282 279283 BSP 1 1/2" female Storz C BS 336 2 1/2" male NH 1 1/2" female 5 Flow rate 360-475-550-750 l/min Weight: 5. • Multiple pattern detents for positive pattern positioning combination fog • and straight stream. Heavy duty and replaceable spinning teeth for very fine fog pattern.5 and 2. a flow selection control ring with detents can be set for a flow of 50. 3 kg. Outlet: BS 336 2 1/2" female coupling. Inlet: Storz C coupling. Weight: 0. other end BS 336 1 1/2" male. nOzzLES nozzles Dual flow foam attack nozzle With twist ring 230-475 l/min. Stream Dispersion Jaws. 279302 279303 BS 336 2 1/2" male NST 2 1/2" 279302 175 Forest fighting equipment: please refer to page 204 f. 263450 universal Joint 45° In connection with RB nozzles with BSP female thread 1 1/2" the joints ensure an operation of 45° in all directions without moving the hose. 267920 267925 267940 Storz C Storz 65 NH 1 1/2" female and male 279410 Elbow support 45° Facilitates operating with nozzles by deflecting the recoil and increasing the mobility of the fire-fighter. 279400 one end BSP 1 1/2" male. one end BSP 1 1/2" male. other end BS 336 2 1/2" male. Inlet: BS 336 2 1/2" male coupling. Outlet: Swivel Storz C. Trigger Shutoff.3 kg. other end Storz C coupling. 279410 5 279400 / 279535 279420 Elbow support "Ergonomic" For all SelectFlow and ProJet nozzles Facilitates operating with nozzles by deflecting the recoil and increasing the mobility of the fire-fighter. one end BSP 1 1/2" male. FITTInGS. Inlet: Storz 65 coupling. Outlet: Swivel Storz 65.3 kg. Weight: 0. COupLInGS. 267920 267900 . 263450 CAFS nozzle C-D25 Coupling Storz C.FIRE HOSES. Outlet: Swivel Storz B. 267900 267850 26790001 26790002 Inlet: Storz B coupling. Weight: 0. shield and adapter forged in aluminium alloy. with BS 336 2 1/2" male.800 l/min. Weight: 4. therefore working without manpower possible.400 l/min. at 8 bar: 10 m. with BS 2 1/2" male. at 8 bar: 1. Throw width at 5 bar: 27 m. at 8 bar: 32 m.5 kg. Throw height at 5 bar: 7 m. Throw height at 5 bar: 9 m. Hydro-Shield . 5 265400 Hydro-Shield Body cast. with Storz 38. In use the unit is firmly pressed to the ground by the water pressure. Throw width at 5 bar: 28 m. with instantaneous 1 1/2" male. at 8 bar: 31 m.5 kg. Flow rate at 5 bar: 200-700 l/min. Hydro-Shield Flow rate at 5 bar: 800 l/min. gases.5 kg. 8 m at 8 bar. Weight: 2. at 8 bar: 9 m. at 8 bar: 1. shield and adapter forged in aluminium alloy.5 kg.5 kg.adjustable water flow Body cast. 265400 265401 265402 265404 with Storz C. Weight: 2. Weight: 2. Come complete with coupling.176 HYDRO-SHIELD To build up a large water wall.5 kg. Width of water wall that can be produced with this shield of 24 m at 5 bar. 265410 265411 265413 with Storz B. 265300 . to protect against flames.100 l/min. 265300 265302 with Storz C.5 kg. with BS 336 2 1/2" male.000 l/min. Several units can be chained up for wide water blockings. Weight: 2. Flow rate at 5 bar: 1. 27 m at 8 bar. Water height of 6 m at 5 bar. Weight: 4. at 8 bar: 300-1. Weight: 4. With Storz 65. smoke to cool objects. Comes complete with coupling. with instantaneous 1 1/2" male. Weight: 5. hay stacks. with NH 1 1/2" female. with BS 336 2 1/2" male. with NH 1 1/2" female. chip bunkers etc. Weight: 3 kg. Output: 350 l/min at 8 bar. Length: 1. Weight: 3. High cooling effect through special arrangement of the individual nozzle tips. Particularly suitable for extinguishing burning liquids such as oils and paints.6 kg.15 kg. Weight: 3. with Storz 65. COupLInGS. Weight: 7 kg. Suitable for use in low. Output: 350 l/min at 8 bar. Weight: 5. Weight: 3. Weight: 7 kg.FIRE HOSES. with instantaneous 1 1/2" male. Provided with ball type valve and coupling. Weight: 5. Weight: 5. FOG nOzzLES Good extinguishing efficiency and strong cooling effect through intensive water atomization. 265210 5 265000 265010 265011 265012 265013 with Storz C. Weight: 3. Weight: 7 kg.5 kg. with BS 336 2" male. Fog nozzle "MOnSOOn 410 mm" Special branch pipe for normal pressure (5-8 bar) fog. Output: 400 l/min at 8 bar. and the water will reach the fire smouldering deep down. with Storz 65. 265000 Fog nozzle "MOnSOOn 1180 mm" Special branch pipe for normal pressure (5-8 bar) fog. Provided with ball type valve and coupling. Length: 180 cm.1 kg. FITTInGS. 265100 . Weight: 7 kg.2 kg. Weight: 5.and high-voltage installations. High cooling effect through special arrangement of the individual nozzle tips.2 kg. Weight: 5. with instantaneous 1 1/2" male. Provided with ball type valve and coupling.5 kg. The lance is pierced into the stack.5 kg. nOzzLES nozzles Extinguishing lance Special branch pipe for fire fighting in coal dumps. 265200 265210 piercing applicator 6” with 1 1/2" female thread. 177 265200 265202 265204 265201 with Storz C.180 mm. 265100 265110 265111 265114 265112 with Storz C. with Storz 65. with BS 336 2 1/2" male. Comes with 45 degrees elbow piece for easy handling.5 kg.5 kg. Length: 410 mm. In practical terms. There is just a quarter turn between full jet and fire-fighter protection water shield. reel and pump. . safety and ergonomics in confined space fire-fighting Certified as to EN 15182-4 Optimum extinguishing: The combination of high-pressure technology and O-stream nozzle facilitates the especially fine atomisation of the water. The small droplets evaporate completely and thus extract a maximum amount of energy from the fire. The front hand is free to guide or adjust the spray. Water can be applied in short shots or in finely gauged volumes using the self-locking trigger.178 nepiRo Ergo HIGH-pRESSuRE FOG Gun For greater effectiveness. recoil is conducted directly into the rear hand and the pistol lies in a completely neutral grip. which means that the complete range of adjustments can be used without a change of grip. The flush setting of the nozzle and the special design of the valve allow the washing out of impurities of up to 5 mm during operations. Ergonomic design: As a result of the special design of the gun. hard-coated aluminium for the nozzle and special stainless steel valve pistons make the NEPIRO wear-resistant. the large support area allows the NEPIRO to be comfortably rested on the body. this results in the optimum extinguishing effect of the agents employed. The shape of the jet can be adjusted to the operational conditions in a flash by simply rotating the nozzle. A special plastic coating (PUR) provides protection for the nozzle and the body against mechanical loads. 5 1 2 3 4 1) 2) 3) 4) Full jet 30° narrow spray 60° wide spray Self protection water shield Operational safety: Anodised cast aluminium for the body of the gun. The oil damped valve ensures gentle closing and prevents pressure shocks (water hammer) on the hose. The gun is thus safe against clogging. In the case of lengthy operations. but nonetheless very light. stainless steel piston Housing Cast aluminium with plastic coating (PUR) Feeding Ball bearing mounted rotary feedthrough with a G3/4" outer thread. brass coupling STORZ 38 L x B x H approx.1 kg. nOzzLES nozzles Technical data Flow rate High-pressure version 0 -200 l/min at 40 bar Normal pressure version 0-180 l/min at 10 bar Spray types O-stream nozzle with infinite adjustment Throw range Up to 30 m with full jet Valve Self-locking valve with oil damping and wear-resistant. COupLInGS. 3.FIRE HOSES. various coupling systems available on request Dimensions Incl. brass coupling STORZ 38 approx. 540 x 80 x 350 mm Weight Incl. FITTInGS. 179 High-pressure fog nozzle "nepiRo Ergo" 063783-001 with STORZ 38 brass coupling HD 063783-002 with G 1" female thread HD 063783-008 with OETIKER SV coupling HD 063783-016 with STORZ 32 brass coupling HD 063783-101 with STORZ C coupling ND 529550-001 5 Recommended Accessories 529550-001 Foam tube for "nepiRo Ergo" 521504-001 Bracket for "nepiRo Ergo" 052516-003 Velcro belt for bracket for "nepiRo Ergo" 525863-001 Bracket for foam barrel 521504-001 . Foam compound inlet with adapter Storz D (1").180 FOAM MAKInG BRAnCH pIpES Medium Foam-Making Branch pipes Medium foam-making branch pipes using multi-purpose foam compounds produce foam with an expansion ratio between 40–75. They are light. oils. Connect the Z-Select on the suction inlet of the foam inductor. The water/foam compound solution emerges under pressure from the nozzle inserts which are fitted in a nozzle disc in an annular arrangement. When using special foam compounds. Foam is produced. The guide tube inside the branch pipe turns the foam into a solid foam jet. 0. On account of the high density of the foam it is possible to attain considerable throwing distances. 701750 Specification: The branch pipe is made of stainless steel. heavy foam will prove to be most effective in extinguishing fires of hydrophilic liquids such as methyl-alcohol. Inline Inductor Inline inductors are useable in hose lines for the proportioning of constant foam liquid quantities on protein and synthetic multipurpose base. The operating pressure at the branch is 5 bar. Protection ring and handle in rubber. The entering air stream mixes with the jets of the water/ foam compound solution. handle. The pipe is made of stainless steel. The medium foam making branch pipe consists of the following parts: foam screen.g.1 %. pressure gauge and ball valve shut off. enabling fire from a fought from a safe distance. Adjustable admixing ratios of 0. Body: copper alloy cast Filter and drive nozzle: stainless steel Pipe and adapters: aluminium alloy forged Collector nozzle: Ultramid Diaphragm: Viton Comes with integrated handle. 700075 5 700050 703500 703480 . Heavy Foam-Making Branch pipes Heavy foam-making branch pipes are characterised by a capacity for long throwing distances. Tube made of stainless steel. The design of the proportioning part enables an exact liquid admixing rate between 1 and 6 % of the passing water quantity. Specification: water inlet and mixture outlet complete. Adjustable Foam-Making Branch pipe Like medium foam making branch pipes but with adjustable from medium foam to heavy foam. Complete with ball valve shut off. and isopropyl alcohol. petrol. They can be employed for many fire fighting purposes. compact. convenient. 703480 z-SELECT admixing adapter Couplings Storz D on both sides. greases). This causes a formation of fine spray jets which draw air through their injection effect. and permit very manoeuvrable and effective operations. nozzle body. The admixing adapter for wetting agents as accessory for all standard Z2 and Z4 DIN 14 384 inductors. foam barrel. fires of solid material and also for burning liquids (e.5 % and 1 %. Non-return valve integrated. The inline inductors can be used with heavy and medium foam nozzles. Their compact foam jet achieves a good throw range. Diameter 38 mm. Storz C 1 NH 2 /2" 8 8 8 10 10 10 12 8/20 8/20 8/20 20 20 20 20 20 20 20 20 20 - 545 545 545 630 630 630 680 630 680 680 870 870 870 870 1090 1090 1090 1090 975 375 375 375 375 375 375 375 375 518 518 205 205 205 270 270 270 285 205 270 270 98 98 98 98 126 126 126 126 126 - 4. Protection ring plastic Adjustable Foam Making Branchpipes 701730 701734 701732 701740 701741 701742 701750 700075 700080 700083 700050 700056 700055 700054 700060 700063 70006504 700064 700070 703500 703510 703512 703520 703600 M2 M2 M2 M4 M4 M4 M8 S2-M2 S4-M4 S4-M4 S2 S2 S2 S2 S4 S4 S4 S4 S8 Z2 Z2 Z2 Z2 Z4 Z4 Z4 Z4 Z8 Z8 200 200 200 400 400 400 800 200 400 400 200 200 200 200 400 400 400 400 800 200 200 200 200 400 400 400 400 800 800 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 - 5 5 5 5 5 5 5 5 5 - 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 - -1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6 - 1:50 1:50 1:50 1:60 1:60 1:60 1:40 1:50 1:50 1:50 1:15 1:15 1:15 1:15 1:15 1:15 1:15 1:15 1:15 - 1. COupLInGS. Storz B Storz C Storz C BS 2. one end with Storz D coupling.1 kg.5" m/f. Z8 800 - - - - - - - - 518 - 11 Suction hoses pVC For inline inductor Z 2. nOzzLES Foam Making Branch pipes Admixture Rate Pressure (bar) Protein (%) Multi Purpose Foam (%) 181 Order No. Diameter 25 mm.7 2.5 4. Weight: 2. made of gunmetal.5" m/f.5" m NH 1.7 2.4 2. Weight: 2. NH 2.3 5.5 6 7. 5 Inline Inductor 703611 703610 703609 703700 703710 703715 BS 1. Diameter 38 mm. Pipe in stainless steel. Weight: 1. Length: 2 m. Weight: 2.5" m NH 2. made of gunmetal. Storz C BS 1.5 5.5" m BS 2.6 kg. BS 2.4 2. Weight: 1.4 2. made of light alloy. made of gunmetal. made of light alloy. Storz B Storz C BS 1.5" m Storz C BS 1.5" m Storz C BS 2.5" f.2 1.5" m BS 2.5" Storz B BS 2.8 2.8 7.2 1.5" /f.5 kg.2 1.2 2. one end with coupling Storz 38.7 4.5 4.8 - 10 10 10 24 24 24 32 10 24 24 3 3 3 3 3 3 3 3 3 - Storz C NH 1.5" f. Pipe in stainless steel.3 4.2 1.4 4.6 2.6 kg. Diameter 52 mm. Length: 3 m.5" BS 2. NH 1. Type Flow Rate (t/min) Expansions Rate Protein (%) Multi Purpose Foam (%) Foam Quantity (m3/min) Protein (%) Multi Purpose Foam (%) Coupling Throw Range (m) Length (mm) Diameter (mm) Weight (kg) Medium Foam Making Branchpipes with ball valve shut off. BS 2. Weight: 2.5" f.3 4.5" /f. with coupling Storz C. 703830 703820 703810 .FIRE HOSES. one end with coupling Storz 38. Length: 2 m. with coupling Storz C.5 m. Length: 2 m. FITTInGS.5" m NH 1. Length: 2 m.8 kg. made of gunmetal.4 4. Diameter 38 mm.6 kg.5 5. Length: 1.2 1. Z 4 and Z 8.5" m/f.5 6. 703810 703820 703830 703840 703850 703854 Diameter 25 mm.5 7 7 7 7 7 7 7 7 11 11 Heavy Foam Making Branchpipes complete with ball valve shut off. one end with Storz D coupling.5" /f.2 1.5 4. Protection ring plastic. for both types. therefore fully ex-proof. electric cable ducting. 706485 706490 with Storz C couplings. etc. paints and solvents stores. engine rooms. It is ideally suited for all total flood applications such as in warehouses. Variable in-line foam inductor.5" diameter. It can be used to extract smoke at the rate of 285 m3/min. Weight: 50. and can also be used as a smoke extractor. After flooding a basement. the extractor can be used to dispose of the foam.3 kg.6 m of special smoke trunking is supplied which can easily be attached. Complete with foam compound pick-up tube. or similar high-risk areas. 15 m long. polyethylene collapsible smoke suction ducting for combi version. 7.5 m collapsible smoke suction ducting and 30 m polyethylene exhaust ducting. Maximum foam expansion: 1200 times.3 kg.45 kg. with BS 2 1/2" couplings. Mobile foam unit "RB 140" Designed for rapid one-man deployment. for connection to a hydrant or any other suitable pressure source. suitable for use with all foam compounds. Spare parts for Fomax 7: 706700 706810 706820 nylon foam net for standard and combi type. Air Flow (m3/min) 4. One "Viking" hose 15 m long fitted with a foam making branch pipe (225 l/min throughput couplings 2.000 1. polyethylene exhaust ducting 30 m long.2 185 7. Two solid rubber tyres 400 mm diameter. machinery spaces. Empty weight: 72 kg. nylon foam net.8 285 Typical performance figures: Bypass Control Open Water pressure (bar) 4 7 10 4 By-Pass Closed 7 10 Total Water Flow (l/min) 170 225 270 150 200 240 By-pass Flow (l/min) 50 80 100 nil nil nil Flow to nozzles (l/min) 120 145 170 150 200 240 Foam production 96 159 204 82 140 192 Foam expansion 800 1. One "Viking" fire hose 1.5" as per BS 336) will be used for throughout.200 550 700 800 706490 5 Delivery scope: The Fomax 7 comes complete with couplings. ship holds. 707020 707020 .182 pORTABLE FOAM GEnERATORS portable foam generator set "FOMAX 7" Portable high expansion foam generator. The unit is of the dual use type. ideal for protection of oil storage and loading terminals. Maximum foam output: 200 m3/min. 140 litres capacity.75 kg. with a throughput of 225 l/min. hangar or building with High Expansion Foam. Weight: 21 kg. Weight: 8. Fomax 7 Smoke Extraction: Fomax 7 is available as a dual-purpose model. Smoke Extraction: Water pressure (bar) Approx. Chemical resistant glass fibre reinforced tank.1 240 9. powered by a maintenance-free water turbine. 7. Only requires connection to a suitable pressurised water supply. at 7 bars. Weight: 0. Weight: 50. 1.500 l/min. Electrical system Throw range Weight . 14 kg.400 l/min. The turret is designed for a maximum flow rate of 1000 l/min. electronic turret controls water: up to 65 m for full jet. electronic turret controls water: up to 70 m for full jet. 1. COupLInGS.500 l/min or dry-powder turret for up to 20 kg/s are possible.FIRE HOSES. 40 kg. tilting angle -50° through +80° water: up to 70 m for full jet. 10 bar approx. Configurations as water or foam turret for up to 1. 10 bar approx. Turret RM 25C Thanks to its compact footprint. the remote-controlled electronic RM 25C turret is suitable for use as both a bumper turret and as a roof turret for aircraft rescue and firefighting vehicles and municipal firefighting vehicles. 10 bar approx. Flow rate Angle of rotation Electrical system Throw range Weight up to 1.000 l/min at 10 bar rotation angle 270°.400 l/min. non air aspirated foam. Flow rate Angle of rotation Electrical system Throw range Weight up to 1. Flow rate Angle of rotation Throw range Weight up to 2. 183 Turret RM 15C The RM 15C by ROSENBAUER is a compact turret with a broad field of applications. tilting angle . Its cost-effectiveness is impressive.500 l/min at 10 bar rotation angle 270°. It can be deployed as a bumper turret on an ARFF or as the main turret on a municipal fire fighting vehicle. FITTInGS.400 l/min at 10 bar 360° infinite. 25 kg. 10 bar approx. Controls are fully electronic tracking controls with options such as an oscillator function.or powder operation. electric turret controls water: up to 42 m for full jet. tilting angle -40° through +70° 12V or 24V. Turret RM 8E The ROSENBAUER turret RM 8E is depending on configuration a electrically controlled monitor for water-. 2. The body of all turrets is made of cast light alloy.000 l/min. 25 kg. and thanks to various options it can handle a variety of requirements for manually-controlled turrets. tilting angle -30° through +70° 24V.500 l/min at 10 bar rotation angle 270°. 5 Turret RM 24M The RM 24M turret is the classical manual turret for municipal firefighting vehicles. Flow rate Angle of rotation up to 2.15° through + 65° 12V or 24V.20° through + 70° mechanical. 2. nOzzLES Monitors TuRRETS ROSENBAUER offers several manually and electrically driven turrets with flow rates between 800 l/min an 7000 l/min. electrically preset to . 59 m approx. 65 m at 8 bar. Throw range: max.2 kg. Weight: 17. Flow rate Angle of rotation Electrical system Throw range Weight up to 7. 265435 . Complete with rotation and elevation locking devices.200 l/min: At 1. 2. 6. It offers best-of-breed throw range for industrial and aircraft rescue and firefighting vehicles in combination with new CAN bus controls. tilting angle -18° through +70° 12V or 24V. Large pattern ring allows for production of full stream.600.600 l/min: At 2. The monitor has direct manual control from plus 90° to minus 60°.184 Turret RM 60C The RM 60C is the flagship model in the ROSENBAUER turret family. The monitor has specially been designed to control fires or to provide sufficient water cooling capacity in tank farms. 1.000 l/min. Petrochemical installations etc. light alloy. Weight: 19. 95 kg.5 kg. Fitted with an infinitely adjustable "MasterStream" monitor nozzle tip with flow settings of 1. 10 bar approx. electronic turret controls water: up to 95 m for full jet. light alloy. wide and narrow angle fog. Maximum throw: At 1. 2 x BS 2 1/2" male.700 l/min: 55 m approx.200. light alloy. and to combat fires. 66 m approx. 265430 265435 265436 2 x Storz B. Will rotate with a 360° degrees sweep. Water ring monitor Made of corrosion resistant light alloy. Equipped with a full stream nozzle with an output of max. 265440 5 265440 Stationary monitor model "649" Made of corrosion resistant brass.000 l/min at 10 bar rotation angle 270°.400 l/min.000 or 2. The monitor specially was designed to provide sufficient water cooling capacity in tank farms and petrochemical installations etc.5 kg. Weight: 17. 2 x NH 2 1/2" female. 1430 l/min. 1. Weight: 8 kg. The monitor has hand wheel elevation control from 90° to 30° above horizontal. with Tip 950 -1400-1900 l/min Weight: 8 kg. Comes complete with foam compound pick-up tube 2. Weight: 8 kg. Single Inlet Storz 125. provided with various couplings. Maximum throughput 1.900 l/min at 7 bar.5 long. 2.550. it can easily be stored in fire fighting trucks. Stream Shaper Foam nozzle Brass construction with integrated foam admixing system for 1 or 3%. Fitted with an infinitely adjustable "MasterStream" monitor nozzle tip with flow settings of 1. nOzzLES Monitors portable monitor "RB 6" • Simple and quick operation • Highly maneuverable • Unmanned operation saves manpower • Compact size & lightweight • Elevation is adjustable between 30 degree to 60 degree unmanned • Down to 20 degree when manned • Horizontal rotation is adjustable 20 degrees either side of center • Ball shutoff with locking handle • Compact folding legs for easy storage • Carbide tipped spikes for extended wear and stability • Large handle makes moving easy • Select flow tip 368 (360. 23 kg. Inlet 2 x 2 1/2" BS male. COupLInGS.FIRE HOSES. Will rotate with a 180° degrees sweep. provide 4 orifice options and maximum throw range. Weight: 6 kg.475. with adjustable main current nozzle for 1. with 1 x BSP 2 1/2" female. Pick-Ups and so on.400 l/min. Inlet 2 x Storz 65. 5 265485 Recommended Accessories for monitor "RB 6" and "pOWER STREAM" 265484 Quad Stacked Tips Four separate stacked tips for full stream action. The monitor comes complete with a foldaway ground base and thanks to it’s small dimensions. with 1 x Storz B. that help maintain stability even on uneven ground surfaces. 265484 26548410 265486 265486 . Petrochemical installations etc. Weight complete: approx. Comes with two water inlets.800 l/min. Large pattern ring allows for production of full stream wide and narrow angle fog. with 1 x Storz 65.750. The monitor has specially been designed to control fires or to provide sufficient water cooling capacity in tank farms.900-2. nlet 2 x NH 2 1/2" female. 265485 265492 265487 26548705 265491 Inlet 2 x Storz B.200.950 l/m) 265497 265493 26549305 265500 with 1 x BS 336 2 1/2" male. FITTInGS. Weight: 8 kg.600.900-3.000 or 2. The ground base includes hardened steel ground pikes. 265493 185 Ground portable monitor "pOWER STREAM" Made of corrosion resistant light alloy. The unit comes with an automatic nozzle with a flow capability of 1. provided with a 2. The ground base includes hardened steel ground pikes. In. Comes with a large water inlet. The monitor has specially been designed to control fires or to provide sufficient water cooling capacity in tank farms. ROSEnBAuER elbow support model "Ergonomic" Please refer to page 175.05 kg. 266102 Hose Line pressure Limiting Valve In. Comes with a water driven motor for unattended operation.and outlet provided with a 3" Storz B Coupling. Weight: 5 kg. BS 2 1/2" male. Pick-Ups and so on. Storz B.7 kg. 266101 Hose Line pressure Limiting Valve In. also provided with a BS 2 1/2" female coupling. also provided with a Storz B coupling. Can be operated in any arc up to 30° either side ( 60° total). that help maintain stability even on uneven ground surfaces.420 l/ min and a single line set up.and outlet provided with a Storz-65 coupling. The valve consists of a light alloy body. 5 MISCELLAnEOuS 266100 266100 Hose Line pressure Limiting Valve Certified as to DIN 14380. Storz 65.186 265482 portable oscillating monitor model "OzzIE” Made of corrosion resistant light weight Pyrolite alloy. Weight complete: approx. with pressure gauge and a control ring for setting the required pressure at a range of 2-16 bar.. Separate outlet for overflow water. Will sweep 40 times per minute in a 60° sweep arc. A fluorescent scale allows reading also at night time. Separate outlet for overflow water.and outlet provided with a BS 2 1/2" coupling. Other inlets upon request. Weight: 5. . also provided with a Storz-65 coupling. 265482 26548201 26548202 26548203 BSP 2 1/2" female thread. The monitor comes complete with a foldaway ground base and thanks to it’s small dimensions. it can easily be stored in fire fighting trucks. Petrochemical installations etc.7 kg. 15.5" male instantaneous coupling as per BS 336. Weight: 5. ROSEnBAuER elbow support model "SK 45°" Please refer to page 175. Separate outlet for overflow water. A built-in pressure gauge is also provided. 000 l/min.FIRE HOSES. Storz A. Simply connect and tune on for instant measurement of static pressure.25 kg. with BS 336 2 1/2" male/female. 266600 266610 269700 With couplings Storz B With couplings BS 336 2 1/2" Wrench for underground hydrant. 187 268010 In-Line Ball Type Valves Made of light-alloy. 268210 266600 269701 Hydrant Key British Standard Suitable for opening and closing of underground hydrant valves. 268110 Hose pressure Gauge Measuring range 0-25 bar. Certified as to DIN 3223. width 400 mm. In. 269700 . inlet and out-let provided couplings. Flow rate range: up to 3. COupLInGS. Storz B. with Storz B. made of light alloy.5 kg. 268110 268120 268122 with Storz C. 268010 268020 268030 Storz C. 5 Flow Meter This metering device is a light and compact self powered measuring gauge for dry risers and hydrants. Inlet comes with Storz swivel and outlet solid Storz coupling. Weight: 12 kg. Inlet and outlet with Storz-C coupling. 268210 268220 268221 with Storz C.9 kg. pressure range from 0 to 25 bar. Weight: 7. Length: 1 050 mm. instantaneous flow and total flow. painted black. Weight: 0. Weight: 1. with Storz B. Made of light alloy. with BS 336 2 1/2".3 kg. FITTInGS. nOzzLES Miscellaneous 90° Elbow Made of aluminium.6 kg.6 kg. Made of forged steel. The bar or poker is carried inside the barrel of the key. Weight: 1. Length: 1.9 kg. Weight: 2.and Outlet provided with a 3" Storz-B coupling. Comes with square nut 32 mm. dynamic pressure.3 kg. Comes complete with washers. Weight: 5. Weight: 2. Weight: 1. Weight: 1.100 mm. Weight: 2 kg.7 kg. Weight: 2.5 kg. 5 272650 Hydrant standpipe "BS 750” Complete with 1 x BS 2 1/2" female coupling. Length: 890 mm.040 mm. 271549 272710 Hydrant standpipe BS 750 Made of light-alloy. Weight: 6 kg. Weight: 6. without screw down valve. 272655 Hydrant Standpipe BS 750 With 2 x 2 1/2" female BS couplings. Weight: 4. Length: 1.3 kg.5" BSRT according to BS 750. connected by a chain. female BSRT according to BS 750. 271500 269800 Hydrant Standpipe Model "2B” Certified as to DIN 14375.188 269800 Set of Manhole Cover Lifting Hooks Consists of 2 hooks with grip.5" BS 336 female couplings. Made of light-alloy. Weight: 7. Weight: 7. 271501 Standpipe As per DIN 14375.040 mm.9 kg. Weight: 5. Length: 1.5 kg.5".15 kg. Double delivery outlets with 2. inlet with claw type coupling for the connection to an underground hydrant as per DIN 3221. 271500 272500 Hydrant Standpipe Model "1C” without screw down type valve. without screw-down valves. Two outlets with screw-down type valves and Storz-B couplings. 272500 271549 Hydrant standpipe Brass Standard shaft length 750 mm.4 kg. Comes with two outlets with screw-down type valves and 2. Inlet with 2. One chain with male blank cap. Weight: 1 kg. Weight: 6.2 kg. inlet with claw type coupling for the connection to an underground hydrant as per DIN 3221. inlet with 2. Made of light-alloy. Two outlets with screw down type valves and Storz-65 couplings. 5" female couplings as per BS 336. 272710 .