INFO’ DIAGCITROËN AFTER SALES DIVISION - LEXIA PROXIA CD 41 DIAGNOSTIC TOOLS CITROËN SELLING DEALERS: PDI technicians Campaign co-ordinators N° 421 19/12/2008 AUTHORISED REPAIRERS: Service Managers - Consultant technicians THE CONTENTS OF THIS BULLETIN SHOULD BE MADE KNOWN TO ALL PERSONNEL WHO, DIRECTLY OR INDIRECTLY, USE LEXIA / PROXIA DIAGNOSTIC TOOLS. TITLE: Manual configuration of the BSI ECU on CITROËN C5 (X7). CONCERNING: The operations for configuring a BSI ECU: • • • Following the replacement of an ECU, Following the downloading of an ECU, Checking the configuration. IMPORTANT: Incorrect configuration will affect the operation of the vehicle. Follow the internet configuration procedure described in this document and limit the use of manual configuration just to the cases quoted in the INFO'DIAG. Page 1 / 31 CONTENTS 1 Introduction………………………………….....………………………………………..3 2 Preliminaries………………………………………...……………………………………3 2.1 Safety advice………………………………………………………………………….3 2.2 Technical advice……….…..………………………………………………………..3 3 Operations to be carried out…………........………….….......………………………....4 3.1 Operations to be carried out before removal, downloading or configuration of the BSI……………………………………........................................5 3.2 3.3 Operations to be carried out to configure the BSI…………………………..6 Operations to be carried out after the configuration of the BSI…………8 4 Checking of configuration……………………………………………………………..9 4.1 4.2 4.3 4.4 4.5 4.6 Notes on the configuration tables…………………………………....………..10 Configuration menus…………………………………………………………….10 Customer options…………………….…………………………………………..11 Configuration……………………….……………………………………………..12 ECUs present………………………………….………………………………….29 « VIN code » menu………………………………………………………………31 Page 2 / 31 1 INTRODUCTION Configuration is a sensitive operation, which has direct consequences on the correct operation of the vehicle. Incorrect configuration can have an impact on: • • • Safety (deactivation of vehicle protection devices), Overall functioning of the vehicle (complete loss of or damage to vehicle functions) Vehicle diagnostics (returning of fault codes which may cause the diagnostic tool methods to fail, and lead to the unjustified removal of parts). You are therefore requested to perform the configuration operation following the instructions on this INFO’DIAG in order to ensure customer satisfaction by returning their vehicle in a perfect operational state. 2 PRELIMINARIES The instructions below must be followed to guarantee safety linked to vehicle operation and well-being. 2.1 Safety advice Before starting the engine: • • • Check that the electronic parking brake is activated, If the gearbox is automatic, check that the gear lever is in position «P » (Park), If the gearbox is manual, check that the gear lever is in neutral. 2.2 Technical advice The BSI must be correctly configured before initialising the BSI, initialising the keys or starting the engine. Page 3 / 31 1. downloading or configuration of the BSI: Printing of customer options configuration values Chapter 3.1 and 3. or following the downloading of the BSI: follow chapters 3.2 and 3.3 • • OPERATIONS TO BE CARRIED OUT This chapter describes the steps to be followed to configure a BSI.3. 3.2 only. Chapter 3. If the configuration is being carried out independently of a BSI replacement.2 Operations to be carried out to configure the BSI: A) Configuration by internet B) Choice of maintenance plan C) Manual configuration of customer options D) Checking of certain parameters with manual configuration Chapter 3.1 Operation to be carried out before removal.3 Operations to be carried out after the configuration of the BSI: Initialisation of BSI (or initialisation of keys or synchronisation of high frequency remote controls) Page 4 / 31 . or the downloading of a BSI (checking the correct configuration of a vehicle for example): follow chapters 3. If the configuration is being carried out following the replacement of a BSI. Select the item « Manual configuration ».1 Operations to be carried out before removal. you may replace or download the BSI. then validate using key « * ». or downloading or configuring the ECU.3. Page 5 / 31 . Print the diagnostic tool screen showing the configuration parameter values. or note down these values by hand Return to the Global Test by successive presses on the « Return » key. showing the configuration parameter values (or note these values down manually). Select the item « Configuration ». Select "Diagnosis" Enter the vehicle details. Select the menu « CUSTOMER OPTIONS ». To do so. carry out the following operations: LEXIA or PROXIA 1 2 3 4 5 6 7 8 9 10 Connect the diagnostic tool on the vehicle. establish communication with this ECU on the vehicle using the LEXIA or PROXIA diagnostic tool. if required to do so. Once this operation has been completed. Print the screen « Customer Options » from the diagnostic tool. downloading or configuration of BSI Before removing the faulty BSI ECU. then its RPO number Start the "Global Test" Select the menu « BSI ». . before continuing with the INFO’DIAG procedure from section B). Successively select the menus: . To allow an internet connection. then validate using key « * ». validate using the « F5 » key to configure the parameters returned by the tool.) with successive presses on the « return » key.2 Operations to be carried out to configure the BSI A) Configuration by internet LEXIA 11 12 13 14 15 PROXIA Select the menu « BSI ».« Lighting – Signalling – Visibility – Rear view mirrors ».« Locking – Doors and tailgate – Immobiliser – Alarm ». 18 Return to the main menu of the BSI (« identification ». using key « * » to start configuration by internet. The list of configuration menus appears. The list of configuration parameters appears. Select the item « Configuration by internet ».« Vehicle definition – Equipment – Driving information ». select the submenus: . .« Air conditioning – Cabin heating».« VIN code ». Once the configuration parameters screen has appeared. return 16 the diagnostic tool then validate to the Proxia tool by validating with the « return » key. validate using key « * ». Page 6 / 31 . etc. In each sub-menu and in the ECUs present menu. . 17 NOTE: If the configuration by internet does not work (presence of a message on the tool showing the error code linked to the phrase « it is pointless to repeat the operation »). then validate using key « * ». Select the item « Configuration ». Validate using key « F5 » to launch configuration by internet. . « fault reading ».« ECUs PRESENT ». Check the accuracy of the vehicle’s VIN. NOTE: A monitoring of configuration failures is carried out centrally to correct any configuration malfunctions by internet. . Validate using the key « * » In the « CONFIGURATION » menu.3.« CONFIGURATION ».« Fuel gauge law – Oil level gauge law ». carry out a manual configuration by replacing the internet configuration (based on the configuration tables in chapter 0). . make the connections indicated on Once the tool has received the configuration data. Select the item « Maintenance ». Check (and modify if necessary). etc.« Fuel gauge law – Oil level gauge law ». . return to the main menu of the BSI (« identification ». « fault reading »…) with successive presses on the « return » key. .« Locking – Doors and tailgate – Immobiliser – Alarm ». 30 31 In each sub-menu and in the « ECUs present » and « VIN code » menus. then validate with key « * ». then validate with key « * ». and « VIN code » menus. The parameters to check manually are shaded in grey in chapter 4.1). « ECUs PRESENT ». check (and modify if necessary). Select the item « Manual configuration ». Return to the main menu of the BSI (« identification ». the values of each parameter.« Lighting – Signalling – Visibility – Rear view mirrors ». Page 7 / 31 . « Maintenance – Operational mode of BSI ». LEXIA or PROXIA 24 25 26 27 28 Select the item « Configuration ». In the « CONFIGURATION » menu select the sub-menus: . « fault reading ».B) Choice of maintenance plan LEXIA 19 20 21 22 23 PROXIA Select the item « Maintenance – Operational Switch on the ignition. Once the choice of maintenance plan procedure has been carried out. C) Manual configuration of customer options Manually configure the «customer options » parameters. according to the values on the print-outs or notes. Select the « CUSTOMER OPTIONS » menu. 29 .) with successive presses on the « return » key. using the print-outs or notes previously made (chapter 3. .« Vehicle definition – Equipment – Driving information ». Follow the instructions given by the diagnostic tool: reply to the questions asked by the diagnostic tool. the parameter values shaded in grey in the configuration tables (see chapter 4) Return to the Global Test with successive presses on the « Return » key. LEXIA or PROXIA Successively select the « CONFIGURATION ». D) Checking of certain parameters with manual configuration It is necessary to check certain configuration parameters (since the central base providing vehicle data may not be completely up to date). then validate with key « * ». Select the item mode of BSI ». Select the item « Choice of maintenance plan (new vehicle preparation) ».« Air conditioning – Cabin heating». Select the item « Initialisation ». LEXIA 38 39 40 41 42 43 44 45 PROXIA Select the item « BSI ». Return to the main menus screen of the tool (« diagnosis ».) with successive presses on the « return » key. initialise the BSI ECU (« BSI initialisation »). If the BSI has been downloaded. « downloading». Select the item « pre-defined parameter screens ». then validate using key « * ». The diagnostic tool may be disconnected. etc. Return to the main menu of the BSI (« identification ». or simply synchronise the high frequency remote controls. carry out the following operations to check that the vehicle is able to start. check that the parameter « Transponder label recognised » has the value « Yes ». Select the « BSI Initialisation » menu (or « Initialisation of keys »). or the keys.3. then validate using key « * ». etc. Check that the parameter « Number of keys initialised » has the value « xx ». where « xx » corresponds to the total number of the customer’s vehicle keys. Select the « Parameter Measures » menu of the BSI. Select the « BSI Initialisation » menu (or « Initialisation of keys »). Check that the parameter « Engine ECU locked » has the value « No ». Validate using key « * ». Page 8 / 31 .3 Operations to be carried out after the configuration of the BSI Operations to be carried out only if replacing or downloading a BSI: • • If the BSI has been replaced: initialise the new BSI ECU on the vehicle (« BSI initialisation »). in particular those displayed in the band at the bottom of the screen. then select the sub-menu « Immobiliser ». For each key.) with successive presses on the « return » key. « fault reading ». Follow the instructions given by the diagnostic tool screens. Select the sub-menu « Immobiliser ». depending on what is indicated in the procedure accompanying the recall campaign. Check that the parameter « BSI matched to engine ECU » has the value « Yes ». Once steps n° 32 to n° 37 have been completed. To carry out the initialisation operations. ALL of the customer’s keys and the confidential code card are required. LEXIA 32 33 34 35 36 37 PROXIA Select the item « BSI ». the instruction is not accompanied by any particular text. The parameters will be displayed by the diagnostic tool partially or totally depending on the BSI software version.1 Notes on the configuration tables The display of configuration parameters is conditional on their being present in the BSI software. (2): Means that you have to programme the value indicated in the column « Value to be configured ». If the option or the vehicle definition is easily identifiable. This value is valid for all vehicles.4 CHECKING OF THE CONFIGURATION 4. Configuration notes: (1): Means that you have to programme the parameter according to the absence or presence of the option or to the vehicle definition. (3): Means that this parameter is programmed automatically when you use the procedure « CHOICE OF MAINTENANCE Plan (PRE-DELIVERY INSPECTION) » Page 9 / 31 . An underlined configuration value corresponds to the value to be programmed on all the vehicles. It is prohibited to programme any other value. it is therefore not necessary to configure these if the configuration of the parameters of the « Configuration » menu have been or will be carried out.4. Page 10 / 31 . the following menus are available: Menus Customer options Configuration ECUs present VIN code Pages 11 12 29 31 NOTE: The parameters of the « Customer options » menu are also present in the configuration menu.2 Configuration menus After you have selected the menu « Manual configuration ». With metallic wheel valves. Denmark. Finland. Sweden. (2) For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands. Finland. Norway and Iceland) For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands. Sweden. Sweden. Denmark.4. Norway and Iceland) Type of daytime-running lamps Detection of driver's seat belt not fastened No Simultaneous lighting of daytimerunning lamps and sidelamps Yes Page 11 / 31 . Multiplexed folding electric rear view mirrors Presence of rear screen wiping in reverse gear Type of deflation detection Configure Present if a rear wiper is fitted. Finland.3 Customer Options Configuration parameter Values to be configured No Yes Absent Present Absent Direct without display of pressures No daytime-running lamps Dedicated daytimerunning lamps No Yes No Lighting by default of daytimerunning lamps Yes Comments Driver's door control pad with screenprinted . With rubber wheel valves. button Driver's door control pad with screenprinted button . Denmark. Sweden. Norway and Iceland) For all vehicles destined for the Nordic countries (Netherlands. Finland. Denmark. Norway and Iceland) For all vehicles destined for the Nordic countries (Netherlands. (1) Value not to be configured except on the express request of the customer (deactivation of the alert for detection of driver’s seat belt not fastened). 4.4 Configuration Once the « Configuration » menu is selected. Page 12 / 31 .OIL GAUGE LAW Pages 13 20 23 26 28 The content of each Menu is listed in the following chapters. Menus A B C D E Contents VEHICLE DEFINITION – EQUIPMENT – DRIVER’S INFORMATION AIR CONDITIONING – CABIN HEATING LIGHTING – SIGNALLING – VISIBILITY – REAR VIEW MIRRORS LOCKING – DOORS AND TAILGATE – IMMOBILISER – ALARM FUEL GAUGE LAW . the following screen appears. 0 L diesel (RHR).6 L diesel (9HZ). United Arab Emirates. Without audio equipment.0L petrol (XFV) or 2. Oman. RD4 radio/CD/MP3. Telematic unit (RT4/RT5). Countries Saudi Arabia.7 L diesel (UHZ). 2.2 L diesel (4HP. 2. 2. (2) (2) Key: Parameter to be systematically checked after configuring by internet Page 13 / 31 . 2. Kuwait. 4HT).0 L petrol (RFJ).8 L petrol (6FY). Bahrain.4. Radio navigation (RNEG). (2) Absent Absent Present No Yes Absent Present (1) (1) Configure « present » for vehicles fitted with hydropneumatic suspension with 3. Kuwait. Telematic unit (NG4).1 Menu: vehicle definition – equipment – driving information (menu A) Configuration parameter (A) Value to be configured Absent Present Passenger’s seat position memorisation control unit option Automatic gearbox option Right-hand-drive vehicle Variable damping suspension option Comments All countries other than: Overspeed alert for the Arabian peninsula Saudi Arabia. United Arab Emirates. For engines: Absent Engine oil temperature sensor option Present • • • 1. Oman. Bahrain.0 L petrol (XFV).7 L diesel (UHZ) engine. For engines: • • • • Absent • • • Present Absent Present Absent Present • • Presence of the telematic unit (RT3/RT4) Presence of water-indiesel-fuel sensor Presence of air pump Multifunction screen option (1) The presence of the sensor for detecting water in the diesel fuel filter is visible thanks to the blue 3way connector on the diesel fuel filter. 3. Qatar. Qatar.4. 1. If particle filter absent.2 L diesel (4HP. Depending on the absence or presence of ultrasonic sensors on the rear bumper. With 4 ultra-sonic sensors on the rear bumper only. 2. Type of parking assistance Parking assistance with visual information Parking assistance with sound information Type of deflation detection Type of detection of presence of fuel cap Piloting of the diesel Key: Direct without With metallic wheel valves. Engine ECU Origin of the oil temperature information Engine Relay Unit For engines: Presence of a parking assistance button No Yes Absent Rear Front and rear and available parking space No Yes No Yes Absent Depending on the presence of the button (or the presence of sensors on the bumpers. 2. front and rear) Without ultra-sonic sensors on the bumpers.0 L petrol (RFJ). (2) For engines: • • • • • • • 1. If particle filter present.0 L petrol (XFV). 3. Driver's seat with electric adjustment and memory. Depending on the presence of a towbar. Depending on the absence or presence of ultrasonic sensors on the rear bumper. 4HT). 2. display of pressures No detection By the BSI No particle filter If particle filter absent. 2.0 L diesel (RHR).7 L diesel (UHZ).6 L diesel (9HZ). 1. With 4 ultra-sonic sensors on the front and rear bumpers. Parameter to be systematically checked after configuring by internet Page 14 / 31 . With rubber wheel valves.8 L petrol (6FY).Configuration parameter (A) Origin of the waterin-diesel-fuel information Driving position memorisation option Presence of a trailer relay unit (BSR) Presence and type of vehicle cruise control Value to be configured Engine ECU Absent Present No Yes Cruise control and speed limiter Comments (2) Driver's seat with manual adjustment. 0 L petrol (RHR) or 1. (3) For normal use and engines: For severe use and engines: Key: Parameter to be systematically checked after configuring by internet Page 15 / 31 . Configure 2500 km for vehicles with an RPO number < 11480 and which have not had their first service.6 L diesel (9HZ). 2. For vehicles fitted with a 2. 0 km Threshold for first service 2500 km Maintenance Speedometers in kilometres . 2.8 L petrol (6FY) engine. 1. 3. Configure 0 km for vehicles with an RPO number ≥ 11480 (14th April 2008) or for vehicles which have had their first service. 4HT).0 L petrol (RHR) or 1. 1.0 L petrol (RFJ).CASE N°1 threshold (marketing) (3) For severe use and engines: 15 000 km • • • • 20 000 km • • • • • 2. 1.Configuration parameter (A) fuel additive pump Value to be configured Control by wire Standard Comments If particle filter present. 2.2 L diesel (4HP.0 L petrol (XFV).8 L petrol (6FY). For vehicles except those fitted with a 2.6 L diesel (9HZ). (1) Type of alternator Controlled Presence of available parking space button Presence of available parking space warning lamp Total time before next maintenance No Yes No (2) (3) 12 or 24 months 12 months for « severe » use of the vehicle.8 L petrol (6FY) engine.7 L diesel (UHZ). 2.0 L petrol (RFJ). 24 months for « normal » use of the vehicle.0 L diesel (RHR). 2. 2. 2.CASE N°2 (3) For severe use and engines: 16 000 km • • • • 20 000 km • • • • • • 32 000 km • • • • Duration before 1st service Kilometre threshold for forcing of customer mode Memorisation of faults Presence of an electric secondary brake Electrically adjustable rear seats Key: Parameter to be systematically checked after configuring by internet Page 16 / 31 2.2 L diesel (4HP.6 L diesel (9HZ). 1.7 L diesel (UHZ).Configuration parameter (A) Value to be configured Comments (3) For normal use and engines: • 1. 4HT).0 L petrol (XFV). 2.0 L diesel (RHR).0 L petrol (XFV). (3) For normal use and engines: For severe use and engines: (3) For normal use and engines: 00 months 250 km Authorised No Yes Absent (2) (2) (2) (3) (1) (2) .7 L diesel (UHZ).0 L petrol (XFV).0 L petrol (RFJ).6 L diesel (9HZ).0 L diesel (RHR). 1. 1.8 L petrol (6FY). 2. 2. • • • • 30 000 km Speedometers in miles . 3.8 L petrol (6FY).0 L petrol (RFJ).0 L diesel (RHR). 2.8 L petrol (6FY). 3. 3. 4HT).2 L diesel (4HP.7 L diesel (UHZ).2 L diesel (4HP. 1. 2. 2. 4HT). 2. 0 L petrol (RFJ). 2. With electrical adjustment of the height and reach of the steering wheel.6 L diesel (9HZ). .Configuration parameter (A) Presence of the welcome function for the driver Value to be configured No Yes Comments With manual adjustment of the height and reach of the steering wheel. Yes (2) 3 km/h Absent Present (2) (1) Depending on presence of a button for deactivation of the function. 2.8 L petrol (6FY). Hydraulic power steering. For engines: Engine relay unit (BSM) Origin of the oil pressure information Engine ECU Number of switches for non-fastening of seatbelts Sensor for detection of presence of a front passenger Detection of nonfastening of the driver's seatbelt Detection of nonfastening of the front passenger’s seat belt Presence of a radio RD4 Presence of a red warning lamp for the Steering Assistance alert Presence of an orange warning lamp for the Steering Assistance alert Tolerance on value set for the cruise control / speed limiter Lane Departure Warning System option Key: Parameter to be systematically checked after configuring by internet Page 17 / 31 • • • • • • • 3. 2. For engines: 5 Absent (2) (2) Yes (2) Yes No Yes No Yes (2) (1) Mechanical power steering.2 L diesel (4HP. 4HT). 1.7 L diesel (UHZ). 2.0 L diesel (RHR). 1.0 L petrol (XFV). Petrol.7 L diesel (UHZ). Without audio equipment.Configuration parameter (A) Value to be configured No Comments All diesel engines except: • • • 2. NG4) or radio navigation (RNEG). With radio/CD/MP3/RD4 or telematic unit (RT4. On engines: Presence of a fuel pump Yes Presence of a boot relay unit Type of vehicle No Saloon Estate (2) (1) Presence of HeadUp display Presence of a mobile deflector Presence of HandsFree Kit Presence of CD changer Detection of nonfastening of middle rear passenger’s seat belt Detection of nonfastening of rear LH passenger’s seatbelt Detection of nonfastening of rear RH passenger’s seatbelt Presence of an audio equaliser amplifier Sound alert for parking assistance emitted by switch module under steering wheel Key: No (2) No No Yes Absent Present Yes (2) (1) (1) (2) Yes (2) Yes (2) No Yes No Yes (1) Depending on the presence of a bass box in the boot. RT5.7 L diesel (UHZ). 2. Parameter to be systematically checked after configuring by internet Page 18 / 31 . Present. 1.Configuration parameter (A) Display of fuel consumption without overconsumption due to regeneration of the particle filter Time of response by the engine ECU to the BSI during operation of cruise control Display of the rear seat belt fastening alert on opening of a rear door or switching on the ignition Retention of braking (by the ESP) for 2 seconds when starting on a gradient Battery charge estimation function Presence of massaging front seats Presence of a Built-in Hydraulic Interface (BHI) Presence of power steering Presence of services module Presence of a navigation system (NG4) Presence of a radio RD4 Presence of HandsFree Kit Key: Value to be configured Comments No (2) • 0.6L diesel (9HZ) engine and BSI software version = 5. (1) (1) (1) Parameter to be systematically checked after configuring by internet Page 19 / 31 .2 s Yes (2) No Yes Handbrake with warning lamp. Hydropneumatic suspension With mechanical power steering. performed by the Battery (2) charge status control unit No Yes No Yes No Yes No Yes No Yes No Yes No Yes (1) Metal suspension.6 s • • All engines except 1. With hydraulic power steering. 1.30. (presence of an electro-pump) (1) Configure « yes » if a telematic unit (NG4) with emergency call button is present. 1.50.6 L Diesel (9HZ). Electric secondary brake.6L diesel (9HZ) engine and BSI software version ≥ 6. Configuration parameter (A) Presence of CD changer Presence of massaging front seats Value to be configured No Yes No Yes Comments (1) (1) 4. For a diesel engine with additional heating. Type of sunlight sensor For Bi-zone Automatic Air Conditioning (separate Bi-zone sunlight adjustment of the temperature and air distribution on the sensor left-hand side and right-hand side). Mono-zone For Mono-zone Automatic Air Conditioning. (2) No Mono-zone sunlight sensor For Mono-zone Automatic Air Conditioning.4. For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). For a diesel engine without additional heating.2 Menu: air conditioning – cabin heating (menu B) Configuration parameter (B) Presence of the pollution sensor Presence of humidity sensor in the cabin Value to be configured No Yes Comments For Mono-zone Automatic Air Conditioning. Type of air mixing Bi-zone Mono-zone Type of air distribution Bi-zone Absent Heating elements Autonomous burner Key: Type of additional heating Parameter to be systematically checked after configuring by internet Page 20 / 31 . For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). For Mono-zone Automatic Air Conditioning. For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). For petrol engines. • 2. 1.0 L diesel (engine plate RHR).0 L petrol (engine plate RFJ). For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). (2) Presence and type of blown air sensor Presence of electric sun blind Bi-zone No Key: Parameter to be systematically checked after configuring by internet Page 21 / 31 .34 Mono-zone For engines: • 2. For Mono-zone Automatic Air Conditioning. 1.28 For engines: • 1.24 Aircon compressor drive ratio 1. For engines: • • • 3 L petrol (engine plate XFV).7 L diesel (engine plate UHZ). For engines: 1.6 L diesel (engine plate 9HZ).Configuration parameter (B) Value to be configured Programmable burner 1.8 L petrol (engine plate 6FY). 2.2 L diesel (engine plate 4HP and 4HT).19 Comments For a diesel engine with programmable additional heating. • 2. Martin. Barbados. Egypt. Denmark. Slovenia. Bermuda. Mozambique. Papua New Guinea. Azerbaijan. Reunion. Cameroon. Senegal. Martinique. French Polynesia. Nigeria. Italy. Czech Republic. Switzerland. Somalia. Tonga. Honduras. Macao. Antigua & Barbuda. Paraguay. Cape Verde. Iceland. Georgia. Greece. Pakistan. Israel. St. Uruguay. Bosnia. Comoros. For vehicles destined for the following countries: Albania. Iran. Guyana. Haiti. El Salvador. Ireland. Spain. Luxembourg. Burundi. Australia. Temperate (-17°C to +37°C) Cold (-25°C to +37°C) Very cold (-30°C to +37°C) Type of climate Hot (-17°C to +45°C) Very hot (-17°C to +50°C) Key: Parameter to be systematically checked after configuring by internet Page 22 / 31 . Ecuador. Brazil. Zimbabwe. Mauritania. Seychelles. New Caledonia. Guadeloupe. Chile. Liberia. Tanzania. Malawi. For vehicles destined for the following countries: Armenia. Congo. Lithuania. Fiji. Argentina. Turkmenistan. Bangladesh. Niger. Djibouti. Peru. Finland. Trinidad & Tobago. Burkina Faso. Guinea. territories or departments: South Africa. Ukraine. Tajikistan. Jamaica. Kenya. Kazakhstan. Cyprus. Mauritius. Costa Rica. Brunei . Iraq. Slovakia. Cambodia. Belgium. Lucia. Mali. Estonia. United Kingdom. United Arab Emirates. Mayotte. Malaysia. Kirghizistan. Gabon. Bulgaria. Malta. Guatemala. Qatar. Benin. Bahamas. Indonesia. Colombia. Bahrain. Romania. Sweden. Laos. Togo. Metropolitan France. Japan. Belarus.Configuration parameter (B) Value to be configured Comments For vehicles destined for the following countries. Palestine. Aruba. Poland. Nicaragua. Libya. Oman. Sudan. Madagascar. St. Uganda. Bolivia. Ivory Coast. New Zealand. Chad. Hungary. South Korea. Austria. Ghana . For vehicles destined for the following countries: Algeria. Botswana. Myanmar. Zambia. Panama. Macedonia. Grenada. For vehicles destined for the following countries: Saudi Arabia. Norway. Namibia. Croatia. Morocco. Taiwan. Tahiti. Venezuela. Syria. Lebanon. Kuwait. Latvia. Philippines. Cuba. Ethiopia. Germany. Jordan. Hong Kong. Russia. Singapore. Mexico . Yemen. Vietnam. Sierra Leone. Surinam. Uzbekistan. Portugal. Angola. Rwanda. SerbiaMontenegro. Central African Republic. Tunisia. Netherlands. Moldavia. India. Dominican Republic. Gambia. Sri Lanka. Thailand. Turkey. Configure Present if the vehicle is fitted with a wipers stalk with « auto » position. Present (2) No Yes (1) Key: Parameter to be systematically checked after configuring by internet Page 23 / 31 . (1) Rain sensor option Headlamp wash option Automatic lighting of instrument panel and multifunction screen depending on external brightness Automatic lighting of hazard warning lamps in the event of impact Guide-me-home lighting option Automatic lighting of hazard warning lamps under heavy deceleration Presence of front foglamps Absent (2) Absent (2) Absent Present Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.3 Menu: lighting – signalling – visibility – rear view mirrors (menu C) Configuration parameter (C) Sunlight sensor option Value to be configured Absent Present Absent Present Absent Present Comments Configure Present if the vehicle is fitted with a wipers stalk with « auto » position. (2) 4.4.Configuration parameter (B) Presence of heated seats Type of aircon pressure sensor Value to be configured No Yes Pressure sensor 30 bars Comments Depending on presence or absence of heated seat controls. Absent (2) Type of headlamps Single filament halogen bulbs Discharge bulbs No daytimerunning lamps Dedicated daytimerunning lamps No Yes No Yes No Yes (1) Type of daytimerunning lamps (1) Presence of a rain and sunlight sensor with wipers with regulated speed Presence of a lighting stalk with four positions Presence of a stalk with one-touch activation of automatic wipe Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.Configuration parameter (C) Multiplexed folding electric rear view mirrors Value to be configured No Yes No Yes Absent Present Comments Driver's door control pad with screenprinted button . Key: Parameter to be systematically checked after configuring by internet Page 24 / 31 . Rear view mirrors indexed to reverse gear Presence of rear screen wiping in reverse gear Lighting of hazard warning lamps on pressing the emergency call button Configure Present if a rear wiper is fitted. (1) Configure yes if the vehicle is fitted with a wipers stalk with « auto » position. Driver's door control pad with screenprinted button . Depending on whether the rear view mirrors are equipped with electric folding or not. Norway and Iceland) For all vehicles destined for the Nordic countries (Netherlands. Sweden. Sweden. Lighting of daytimerunning lamps by default No Yes Simultaneous lighting of daytime-running lamps and sidelamps Presence of parking lamps Presence of headlamp height correctors Presence of the light pack unit No Yes No No No Yes Static lighting controlled by the BSI Dynamic lighting: directional headlamps Absent Present Type of bend lighting If the vehicle is fitted with discharge bulbs. Denmark. Sweden. Presence of rear screen wiping in reverse gear Configure Present if a rear wiper is fitted. Norway and Iceland) For all vehicles destined for the Nordic countries (Netherlands. Denmark. Key: Parameter to be systematically checked after configuring by internet Page 25 / 31 . Finland. Finland. If the vehicle is fitted with halogen bulbs. Yes For all vehicles except those destined for the Nordic countries (Netherlands. Finland.Configuration parameter (C) Activation of automatic lighting of headlamps via the personalisation menu Presence of a third button on the high frequency remote control for switching on the lights Value to be configured Comments No (2) No Configure « No » for vehicles fitted with a motorised boot. Denmark. Norway and Iceland) For all vehicles except those destined for the Nordic countries (Netherlands. Norway and Iceland) (2) (2) Configure this parameter to « No » even if the vehicle is fitted with headlamp height correctors Configure yes if the vehicle is fitted with « light bars » under the fascia. Sweden. Finland. Denmark. 4 Menu: locking – doors and tailgate . (1) (1) Left-hand drive vehicle.4. Comments If motorised boot tailgate. Without ultra-sonic detectors (on the roof console or on the windscreen aperture pillars) With ultra-sonic detectors (on the roof console or on the windscreen aperture pillars) For vehicles destined for Belgium with ultra-sonic detectors (on the roof console or on the windscreen aperture pillars).alarm (menu D) Configuration parameter (D) Opening of the boot using the high frequency remote control option Type of locking Normal locking Number / type of sun roof Type of child lock Passenger door lock No sun roof 1 sun roof blind Electric Mechanical Absent Present No alarm Type of alarm Standard alarm Alarm for Belgium Inviolability mode Anti-pinch function on windows and sun roof Presence of a multiplexed sun roof Opening of the rear screen using the high frequency remote control option Presence of electronically controlled fuel flap When actioning unlocking by high frequency remote control Key: Parameter to be systematically checked after configuring by internet Page 26 / 31 Value to be configured Absent Present Deadlocking If standard tailgate.immobiliser . Right-hand drive vehicle. With a locking control with Deadlocking (to check carry out a Deadlocking actuator test). (2) (3) (2) (2) Active Present on all openers Absent No (2) Absent (2) Simultaneous unlocking of all of the Vehicle with normal unlocking. doors Unlocking of driver’s door only Vehicle with deadlocking. . With a locking control with normal locking (to check carry out a Deadlocking actuator test).4. Configuration parameter (D) Type of fitting of alarm Type of motorised boot tailgate Value to be configured Factory fitted alarm (2) Comments No motorised boot tailgate (1) Multiplexed motorised boot tailgate Absent (2) Presence of specific high frequency receptor (Japan) Key: Parameter to be systematically checked after configuring by internet Page 27 / 31 . 8 L petrol (6FY). 2.0L petrol) (1) For petrol engines. 2.2 L diesel (4HP.0 L diesel (RHR).0 L petrol (RFJ). 2. 1. 4HT). For petrol engines. For diesel engines. 4HT (2.7 L diesel (UHZ).2L diesel) Type of engine: UHZ (2. (2) For diesel engines.7L diesel) Type of engine: 6FY (1.4.6 L diesel (9HZ).0L diesel) Type of engine: 4HP.0 L petrol (XFV).8L petrol) Type of engine: RFJ (2. 2.6L diesel) Type of engine: RHR (2.alert level Fuel gauge law selection of the vehicle Value to be configured Petrol Diesel 71 litres 72 litres 330 ohms 332 ohms 58 ohms 7 litres 8 litres 9 litres Petrol vehicles Diesel vehicles Type of engine: XFV (3. For diesel engines.4.5 Menu: fuel gauge law – oil gauge law (menu E) Configuration parameter (E) Type of fuel Tank capacity Gauge resistance for empty tank Gauge resistance for full tank Fuel gauge law . For petrol engines.0L petrol) Type of engine: 9HZ (1. For petrol and alcohol engines. For engines: Key: Parameter to be systematically checked after configuring by internet Page 28 / 31 . (1) Comments Oil gauge law – engines (1) For engines: Engine relay unit (BSM) Origin of the oil level information Engine ECU • • • • • • • 3. 1. With radio navigation (RNEG). With a telematic unit (RT3. With radio type RD4 (CD or CD/MP3).5 ECUs present Calculator Steering wheel with fixed central controls Airbag High frequency receptor Engine relay unit (BSM) Rain / sunlight sensor Driver's door module Built-In Systems Interface Alarm Parking assistance Instrument panel Value to be configured Present Present Absent Present Absent Present Present Present Absent Present Absent Present Present Absent Audio equipment Present Lane wandering alert Absent Present Absent Present Absent Display Present Trailer relay unit Air conditioning Driver’s seat memorisation control unit Key: Parameter to be systematically checked after configuring by internet Page 29 / 31 Comments (2) (2) (2) (2) (1) (2) (2) Depending on presence of ultra-sonic sensors on the roof console or the windscreen aperture pillar. of a telematic unit (NG4) or of radio navigation (RNEG). RT4 or NG4) or with radio navigation (RNEG). With telematic unit (RT3. Without telematic unit (RT3.4. (2) Without radio type RD4. Depending on the presence of a trailer relay unit (this equipment is necessary if the vehicle is fitted with a towbar). Depending on the absence or presence of 4 ultra-sonic sensors in the rear bumper. Depending on presence of a switch for activation of the function. RT4 or NG4) or with radio navigation (RNEG). (2) (1) NaviDrive telematic unit Absent Present Present Absent Present . RT4 or NG4). Depending on presence of a NaviDrive telematic receiver (RT3 or RT4). Vehicles with metallic wheel valves. press on the « Menu » button of the radio. Configure « present » for vehicles fitted with hydropneumatic suspension.7 L diesel (UHZ) engine. To check for the presence of a handsfree kit.0L petrol (XFV) or 2. Vehicles with hydraulic power steering (presence of an electro-pump).Calculator CD changer Value to be configured Absent Present Comments (1) Configure « Yes » for vehicles with an RD4 radio (or radio navigation (NG4) without service module) and hands-free kit. (1) Vehicles with mechanical power steering. note the presence of the following icon on the right of the multifunction screen. Tyre under-inflation detection Present Absent Present Variable damping Suspension Absent Present Absent Present Absent Electric parking brake Power steering Present Key: Parameter to be systematically checked after configuring by internet Page 30 / 31 . Hands-Free Kit No Yes Windscreen wipers Audio amplifier Steering angle sensor Engine ECU Automatic gearbox / piloted manual gearbox ABS / ESP ECU Present Absent Present Present Present Absent Present Present Absent (2) (1) (2) (2) (1) (2) Vehicle with rubber wheel valves. Configure « present » for vehicles fitted with hydropneumatic suspension with 3. Key: Parameter to be systematically checked after configuring by internet Page 31 / 31 .Calculator Value to be configured Absent Comments Vehicles with halogen headlamps. Vehicles with Xenon headlamps. (2) (1) (1) (2) (2) Directional headlamps Present Yaw / lateral acceleration sensor Additional heating Motorised boot unit Seat belt not fastened warning lamp (TNB) Battery charge status unit Present Absent Present Absent Present Present Present 4.6 Menu: «VIN code » Enter the vehicle’s VIN code (17 characters).