Type Acceptance ReportTAR 1/21B/2 – Revision 3 Boeing 737-800 Aircraft Certification Unit . 43 DATA REQUIREMENTS 3 5. TYPE ACCEPTANCE CERTIFICATE 2 4. NZCAR §21. ICAO TYPE CERTIFICATE DETAILS 1 3. ADDITIONAL NEW ZEALAND REQUIREMENTS 7 CERTIFICATION ISSUES 9 ATTACHMENTS 10 APPENDIX 1 10 Rev.2 : 26 February 2004 i TAR 1/21B/2 — Boeing 737-800 . INTRODUCTION 1 2.Type Acceptance Report TABLE OF CONTENTS EXECUTIVE SUMMARY 1 1. . 1/21B/2 was granted in the Standard Category in accordance with NZCAR Part 21 Subpart B.191.824 kg. Introduction This report details the basis on which Type Acceptance Certificate No. Specifically the report aims to: (a) Specify the foreign type certificate and associated airworthiness design standard used for type acceptance of the model(s) in New Zealand. and (c) Identify any additional requirements which must be complied with prior to the issue of a NZ Airworthiness Certificate or for any subsequent operations.004 Issued by: European Aviation Safety Agency Rev.Type Acceptance Report Executive Summary NZ Type Acceptance has been granted to the Boeing 737-800 Series based on validation of FAA Type Certificate number A16WE. which are now eligible for the issue of an Airworthiness Certificate in the Standard Category in accordance with NZCAR §21.200 lb. 1. including Amendments 36-1 through 36-20 (Stage 3) Engine: CFM56-7B Series Type Certificate: E000055EN Issued by: Federal Aviation Administration Type Certificate: E.) – Structural Design Weight Noise Category: FAR Part 36. in accordance with the provisions of NZCAR §21.3 : 16 September 2009 1 TAR 1/21B/2 — Boeing 737-800 . (See Section 5 of this report for a review of compliance of the basic type design with the operating Rules. Applicability is currently limited to the Models and/or serial numbers detailed in Appendix 1. ICAO Type Certificate Details Type Certificate: Issued by: A16WE Federal Aviation Administration Manufacturer: The Boeing Company Model: 737-800 MCTOW 174. 2. There are no special requirements for import. subject to any outstanding New Zealand operational requirements being met. ( 78. and (b) Identify any special conditions for import applicable to any model(s) covered by the Type Acceptance Certificate.43(c).) Additional variants or serial numbers approved under the foreign type certificate can become type accepted after supply of the applicable documentation. Specific applicability is limited to the coverage provided by the operating data supplied. The 737-838 is fitted with the CFM56-7B26/3 Tech Insertion engine. There are no special requirements for import into New Zealand.and low-pressure turbines to achieve better fuel consumption and lower emissions. The applicant was Pacific Blue Airlines for the 737-8FE. registered ZK-PBA. [Ref: LOPA 378-1264] Revision 2 of the report was produced to include type acceptance of the 737-8BK variant. TAR 1/21B/2 — Boeing 737-800 2 Rev.1377.500 lb. This configuration is also used by Pacific Blue Airlines. Airplane Tabulation number YC146. new 16g HIC compliant seats with front-row inflatable seatbelts (subsequently removed).004. serial numbers 34200 through 34202. The standard VB layout is 180 tourist class seats. 8FE is the customer identification model designation for Virgin Blue Airlines (VB). In the specification the aircraft was originally configured for 189 passengers and certified at a maximum takeoff weight of 155.3 : 16 September 2009 . Line No. This report was raised to Revision 1 under CAA Work Request 4/21B/9 to include another variant and update the report to the latest format. This introduced improvements to the high-pressure compressor. and includes the CFM56-7B Series engine based on FAA Type Certificate no. Variable YL556-558. which was granted on 26 February 2004. and a Panasonic ondemand IFE system. which incorporated extensive changes including an all-new wing. who have a large on-going order for the type. These aircraft have a 12J/156Y cabin layout [Ref: LOPA-378-2101] and incorporate a number of new technical features: Rockwell Collins HGS4000 Head-Up Display (fitted under STC ST00845SE). who have a policy of using a single standard specification for their fleet. undercarriage. The applicant was Jetconnect Limited. registered 5W-SAM. Type Acceptance Certificate The original application for type acceptance of the Model 737-8Q8 was from Polynesian Airlines dated 4 July 2000. Line Number 1446. sealed slats and reduced idle thrust delay after touchdown). 838 is the customer designation for QANTAS. Short Field Performance Package (comprising two-position tailskid. The 737-600/700/800 Series are the “NG” (New Generation) versions of the 737 introduced in 1997. centre fuel tank Nitrogen Inerting System. registered ZK-ZQA through ZK-ZQC. 8BK is the Boeing customer designation for leasing company CIT Aerospace. The 737-800 can be configured for up to 186 passengers at 30 inch seat pitch. This report was raised to Revision 3 to add the 737-838 variant under CAA Work Request 9/21B/15. the combustor. registered ZK-PBC. Jetconnect initially added three new aircraft to their fleet. The first-of-type example was Serial Number 33017. YJ865. [Ref: LOPA-378-0850]) Type Acceptance Certificate No. The first-of-type example was s/n 33796. and type acceptance was granted on 16 September 2009. also for Pacific Blue Airlines. which was type accepted on 13 January 2004. Tab Number YJ932. Tab No. 1/21B/2 was granted on 14 November 2000 to the Boeing 737-800 based on validation of FAA Type Certificate number A16WE. The first-of-type example was serial number 30039. (Polynesian Airlines layout is 12 business and 142 economy class seats. E00055EN or EASA Type Certificate number E. increased spoiler deflection on the ground. winglet lift credit. cockpit and engine variant.Type Acceptance Report 3. and the high. A16WE at Revision 43 dated April 23. NZCAR §21. 1992). 2008 EASA TCDS number E. (Flight deck seats are usually mounted individually and rigidly. 1998 FAA TCDS number E00055EN at Revision 7 dated October 17. 6086 – from §25.562(b)(2). There are no non-compliances and no additional special conditions have been prescribed by the Director under §21.1435(b)(1) Hydraulic Systems – Testing to the system relief pressure of 3400 psi was accepted in lieu of full 1. This is an acceptable certification basis in accordance with NZCAR Part 21B Para §21.) Exemption No.85 VC at FL80. plus the addition of a later amendment status for some paragraphs also as listed on the TCDS. on the basis of satisfactory service history.23.43 Data Requirements The type data requirements of NZCAR Part 21B Para §21.004 at Issue 02 dated 17 October. or were already held by the CAA: (1) ICAO Type certificate: FAA Type Certificate Number A16WE FAA Type Certificate Data Sheet no. which requires the seat tracks to be misaligned 10 degrees and rolled 10 degrees. plus the emissions requirements of FAR 34. This is an acceptable certification basis in accordance with NZCAR Part 21B. 1965. again as detailed on the TCDS.3 : 16 September 2009 3 TAR 1/21B/2 — Boeing 737-800 .562 Emergency Landing Dynamic Conditions – The flight deck seats were exempted from the floor warpage testing requirement of §25. on the basis this was just as effective a means to show system integrity.5 times operating pressure. Compliance was shown by a combination of range-of-motion tests of the complete system (to show adequate separation under structural load) and component testing to the ultimate pressure of 4500 psi. 1965.Type Acceptance Report 4. as FAR Part 25 is the basic standard for Transport Category Airplanes called up under Appendix C.43 have been satisfied by supply of the following documents.) Rev. (ii) Exemptions: Exemption No. June 29. with the exception of an earlier Amendment status for certain paragraphs as specified on the TCDS. 2008 (2) Airworthiness design requirements: (i) Airworthiness Design Standards: The certification basis of the Boeing 737-800 is FAR Part 25 effective February 1. 2009 – Model 737-800 approved March 13. (The FAA stated it was not the intention of the rule to make the birdstrike criteria more stringent at altitude.41. Two special conditions were imposed. as FAR Part 33 is the basic standard for engines called up under Appendix C. as revised by Amendments 25-1 through 25-77 (FR 28949. Exemption No. three exemptions were requested and a large number of equivalent safety findings made. with Amendments 33-1 through 33-15 thereto.6601 – from §25.6425 – from §25.571(e)(1) Damage-Tolerance & Fatigue Evaluation of Structure – The airplane must be capable of completing a flight after structural damage after a four-pound bird impact at the greater of VC at SL or 0. The certification basis of the CFM56-7B Series is FAR 33 effective Feb 1. 395(a) Lateral Control System Load Factors – Boeing proposed not applying the 125 percent of the computed hinge moment to the components of the aileron system which are designed as shear-outs. Boeing provided compensating factors. Issue Paper E-1 Special Condition – HIRF (§25.105. §25. 25. including unobstructed aisle widths of 13” offset 6.735 Rejected Takeoff Performance – Boeing proposed using the accelerate-stop distance requirements contained in NPRM 93-8 in lieu of the respective FAR. As for previous 737 models. (The dry runway criteria are less stringent.3 : 16 September 2009 . but the wet runway and worn brake provisions are stricter.115.613 Material Design Values – This requires design values to be established within specified probability confidences. rather than “traditional” VMIN stall speeds. §25.Type Acceptance Report (iii) Special Conditions: Issue Paper A-2 Proposed Special Condition – Limit Engine Torque Loads for Sudden Engine Stoppage (§25. Issue paper F-4 ESF §25.21(b)(1).813(c)(1) Amdt 25-32. §25.901. The latter must be investigated.361) – Boeing proposed treating this as an ultimate load on the grounds the current rule was less relevant to modern high-bypass engine design with fewer larger fan blades. §25. §25. §25.) Issue paper P-2 ESF §25. only the 1.101. This was accepted by the FAA with imposition of some criteria for stall warning and manouvering margins.813(c) Amdt 25-76.562(c)(8) Amdt 25-64 Emergency Exit Access – For the 737-700 with the “traditional” overwing exit an ESF was granted to allow 2” compression of the outboard seat cushion as encroachment in the exit area. This was accepted because the manual inflation handle is accessible and obvious. as for the 737-300.1333 & 25.812(b)(1)(i) Emergency Exit Locator and Marking Signs – Some variation in stroke-width ratio was accepted because the readability was not affected.1309(b)(1) Flight Critical Thrust Reversers – Boeing contended that the thrust reverser design protects against in-flight reverser deployment to an extent that is equivalent to showing the aircraft is capable of continued safe flight and landing under any possible position of the thrust reverser. They were accepted on the basis of successful history and Boeing substantiation data. in which out-of-balance loads can be significant. Issue paper C-1 ESF §25. The 737-800 uses no new materials or fastenings. Also a low sill-height with uninflated slide is no different to the case where the door is less than 6 feet from the ground. Issue paper A-9 ESF §25. §25.109. §25.113. (The benefits of which have been shown by CAMI testing.) Issue paper C-3 ESF §25.5” from the exit centreline when triple seats are located adjacent to exits. as reference datum for regulatory compliance. because the regulations do not consider such loadlimiting devices. but Boeing traditionally has used materials which have not strictly complied with the requirement. Issue paper F-1 ESF FAR Parts 25/36 – Use of 1-g Stall Speed – Boeing elected to use the 1-g stall speeds. when no slide is required. This was accepted by the FAA after rigorous safety and risk analyses were carried out and compensating design assurance and continued airworthiness features were provided.810(a)(1)(ii) Escape Slides – Because of the length of the activation lanyard needed to allow for door movement there are some (crash) configurations where the escape slide will not automatically deploy. (iv) Equivalent Level of Safety Findings: Issue paper A-5 ESF §25.1431) – A special condition was needed to require showing there would be no adverse effects from high-intensity radiated fields on the electrical and electronic systems which perform critical functions. TAR 1/21B/2 — Boeing 737-800 4 Rev. §25.5 ultimate load factor is applied. Issue paper C-4 ESF §25.933(a)(1)(ii). 979 Pressure Fuelling System – There is a requirement for the capability to check the proper operation of the pressure fuelling system automatic shutoff function before each fuelling.8BK – CAA Accepted as AIR 2855 D631A001.2. (v) Airworthiness Limitations: See Airworthiness Limitations and Certification Maintenance Requirements Section 9 of Boeing 737-600/700/800 Maintenance Planning Document D626A001-CMR. including up to Amendment 34-3.8Q8 – CAA Accepted as AIR 2706 D631A001.CD.10 (ii) Current service Information: Boeing 737-800 Service Bulletins/Letters Engine – CFM56-7B SP.3. See Chapter 5 of the CFM56-7B Engine Shop Manual CFM-TP. NT.Type Acceptance Report Issue Paper P-5 §25.11 and SB on CFMI-TP. CP. This was accepted on the basis of reliable service on other 737 models plus some other factors which will prevent structural and fuel system damage in the event of a float switch failure.1389(b)(3) Position Lights – The forward and rear position lights exceed the maximum allowable intensities for overlap areas A and B. D631A001 D631A001. (3) Aircraft Noise and Engine Emission Standards: (i) Environmental Standard: The 737-800 has been certificated under the noise requirements of FAR Part 36.518 Rev. However the Boeing design does not allow checking of the float switch. This was accepted as the overlap areas are narrow. do not affect signal clarity and provide greater overall intensity.10.SM. The CFM56-7B Series meet the emissions requirements of FAR Part 34.8FE – CAA Accepted as AIR 2847 D631A001.838 – CAA Accepted as AIR 3104 (6) Operating Data for Aircraft and Engine: (i) Maintenance Manual: Boeing 737-800 ILF AMM – Document D633A101-ILF Boeing 737-800 ILF Wiring Diagram Manual – Document D280A106-ILF Boeing 7370800 ILF System Schematic Manual – Document D280A206-ILF CFM56-7B Engine Shop Manual – Document SM.3 : 16 September 2009 5 TAR 1/21B/2 — Boeing 737-800 . TE. including up to Amendment 36-24. Section 4 – Noise Characteristics (4) Certification Compliance Listing: Boeing Report D045A010 – FAA Compliance Checklist 737-600/700/800 Boeing Report D045A010-1 – FAA Compliance Checklist 737-800 CFM56-7B/3 Certification CCL dated 7 June 2006 (5) Flight Manual: FAA-Approved Boeing Model 737-800 Airplane Flight Manual Boeing Document No.10. Issue paper S-17 ESF §25. (ii) Compliance Listing: See AFM or the applicable Supplement. D019A001TCI38P-3 – Rev. D019A001QAN38P-1 – Rev.F B-H430-03-4320 Letter of Definition 737-8FE YJ865 FAA Project TD7808SE-T B-H340-03-4625 LOD 737-8FE Follow-On Airplane YJ866/TD7854SE-T B-H340-09-01295 Boeing Letter (includes details of Major Changes to YL566/7) 737-800 Operations Manual – Document D6-27370 737-800 Maintenance Planning Data – Document D626A001 737-800 Dispatch Deviation Guide – Document D6-32545 737-800 Maintenance Review Board – Document D626A001-MRBR 737-600/700/800 ETOPS Configuration C. D6-38808-18 . 737-838 Doc.myboeingfleet.M. (5) and (6): CAA 2171 dated 26-10-00 from K E Kaulia – Manager Certification Delivery and Fleet Support. Boeing Commercial Airplane Group Note: Since the original granting of the type acceptance certificate Boeing has provided the CAA with access to the website www.Type Acceptance Report (iii) Illustrated Parts Catalogue: Boeing 737-800 ILF IPC – Document D638A001-ILF CFM56-7B IPC – Document PC.P.3 : 16 September 2009 . Boeing has provided access for all variants covered by this type acceptance certificate. 737-8BK Doc. Single Aisle Platform.8Q8 Doc.14 (7) Agreement from manufacturer to supply updates of data in (4). New QANTAS Airways Detail Spec.Rev H 27/10/00 Virgin Blue Detail Spec. This contains all the applicable technical documentation for the aircraft variants for which access has been authorised.com. – Document D044A007 TAR 1/21B/2 — Boeing 737-800 6 Rev. D019A001VOZ38P-1 – Rev. CAA 2171 dated 25-10-00 from B Mungin – GE Customer Support Manager (8) Other information: ILFC Detail Specification Model 737. Model 737-8FE Doc.A CIT Aerospace Detail Spec. 810(c) at Amendment 25-72 FAR Part 25 para §25.2.853(b) at Amendment 25-72 FAR Part 25 para §25.809(b) at Amendment 25-72 Meets FAR Part 25 Certification requirements FAR Part 25 para §25.Shall be those specified in FAR 25. Additional New Zealand Requirements Compliance with the retrospective airworthiness requirements of NZCAR Part 26 is a prerequisite for the grant of a type acceptance certificate. Section 25-50-00.10 D.58: (b) Manufactured after 20/8/90 .2.1 B.1 C. Crew assist space. Waste Bin . Uninterrupted Power. Section 33-51-00 Meets FAR Part 25 certification requirements after 1-5-72 FAR Part 25 para §25.9 D.2” contrasting band. minimum brightness 160 microlamberts Landing Gear Aural Warning .Air Transport Aircraft .807 in effect on 29 March 1993 Floor Level Exits – Definition Additional Emergency Exits – Must meet requirements Emergency Exit Access – All Required Exits must have: Passageway unobstructed 500m wide between areas and leading to a Type I or II Exit.2 REQUIREMENT: MEANS OF COMPLIANCE: Marking of Doors and Emergency Exits Crew Protection Requirements – Agricultural Aircraft FAR Part 25 para §25.1.01.All Aircraft PARA: B. built-in fire extinguisher.020 FAR Part 25 para §25.812(h) at Amendment 25-58 FAR Part 25 para §25.T/C after 1.4 D.1 REQUIREMENT: MEANS OF COMPLIANCE: Doors and Exits (b)(3) Additional Emergency Exits – > 23 passengers Emergency Exit Evacuation Equipment – Descent means Emergency Exit Interior Marking – Size and colour. by exits.More than 9 Pax PARA: C.2. or later Emergency Exit Interior Marking – Clears.T/C after 1.93 (c) Liners shall be separate from the aircraft structure Rev. Emergency Exit Exterior Markings .2 C.Automatic Flap Linking FAR Part 25 para §25. instructions Locations signs above routes. Boeing LOPA-378-0850 Not Applicable – No internal doors FAR Part 25 para §25.Sealed door.3 C.Meet heat release rate and smoke tests of FAR Part 25 in effect 26.811(a)(e) & (f) at Amendment 25-46 Not Applicable – 737-800 not agricultural aircraft Appendix C .4 D.855(b) at Amendment 25-72 TAR 1/21B/2 — Boeing 737-800 .03. illumination. be self-illuminating.729(e) at Amendment 25-75 Appendix D .1 C.810(c) at Amendment 25-72 – See Detailed Spec. incl.855 (c) at Amendment 25-72 – See Detailed Spec. §25-41-00 and §26-14-00 FAR Part 25 para §25.2.Type Acceptance Report 5.807(a) at Amendment 25-72 (a) Complies (b) Not Applicable – no ventral/tailcone exits FAR Part 25 para §25.2. brightness 250 mlb.Placards.5 D. Civil Aviation Rules Part 26 Subpart B .812(f) and (i) at Amendment 25-58 FAR Part 25 para §25. on bulkheads – Meets certification requirements.3 D.812(c) and (e) at Amendment 25-58 See Boeing Detailed Spec.2.Air Transport Aircraft .2.2 D.8 D.811(b) and (d) at Amendment 25-46 Meets FAR Part 25 certification requirements at Amendment 25-77 dated July 1992.813 at Amendments 25-45 and 25-77 (as applicable to any changed structure).2.2 D.6 D. smoke detector system with external warning Materials for Compartment Interiors .1 D. §25.807(c)(3) is at Amendment 25-15) FAR Part 25 para §25.Additional Airworthiness Requirements Appendix B .7 D.791(d) at Amendment 25-72 FAR Part 25 para 25.1.812(b) Amendment 58 (see Equivalent Safety Finding) FAR Part 25 para §25.2.2. Exterior ashtray.811(e) Amendment 79. opening instructions in red or bright chrome yellow.3 : 16 September 2009 7 FAR Part 25 para §25.811(e) at Amendment 25-79 FAR Part 25 para §25.3 D.5 REQUIREMENT: MEANS OF COMPLIANCE: Exit Types . min.01. floor proximity escape path markings Emergency Exterior Lighting – in effect 30-04-72. Last 10 min.Automatic and Independent Emergency Interior Lighting – independent supply.811(f) (See Equivalent Safety Finding) Colour of markings to be determined on a individual basis FAR Part 25 para §25.807 at Amendment 25-72 (except 25.3.58: (a) Each C or D compartment greater than 200 cu ft shall have liners of GFRS or meet FAR 25 in effect 29.2. min. Section 25-61-00 FAR Part 25 para §25.1 D.88 (c) Seat cushions (except flightdeck) must be fireblocked Cargo and Baggage Compartments . FAR Part 25 para §25.2.2. (b) Descent Illumination .853(d) and (e) at Amendment 25-72 (See ESF) – See Detailed Spec.810(a) at Amendment 25-72 (See ESF) FAR Part 25 para §25.More than 19 Pax PARA: D.853(c) at Amendment 25-72 FAR Part 25 para §25. Access to Type III or IV Exit is unobstructed Internal doors must be able to be latched open –placarded Emergency Exit Operating Handles – Markings/Lighting Emergency Exit Evacuation Equipment – Descent means Emergency Exit Escape Route – Must be slip resistant Emergency Lighting (a) Switch Provisions.09. Lavatory Fire Protection . See Detailed.509 Min. capacity.1389/§33-43-00 (4) Instrument Lighting FAR 25. certified to TSO C126] fitted as standard on YJ865) Oxygen Indicators .040 FAR 25. §23-12-00 SELCAL (ARINC 714) fitted as standard. (b) More than 20 pax – Axe readily acceptable to crew Fitted as Standard – See Boeing Detailed Spec.§34-21-00 Dual GPS meeting ARINC 755 fitted as standard – See Detailed Spec. (FAA guidelines specify 5lb. Portable PBE 120l pax. VFR REQUIREMENT: Shoulder Harness if Aerobatic.1303(b)(4) (3) Anti-collision Lights FAR 25. §27-50-00. Compartment – See DS §35-30-00.Instrument and Equipment Requirements PARA: 91. §22-10-10/§34-16-00 Assigned Altitude Indicator Not Applicable – Altitude Alerting Device fitted ELT Installation Requirements To be determined on an individual aircraft basis TAR 1/21B/2 — Boeing 737-800 8 Rev.1305(a)(2) (5) Fuel Contents See Det.3 : 16 September 2009 .541 91.) The applicant elected to re-fit the water extinguisher for NZ-registered aircraft because of the time frame for certification. Equipment FAR 25.531 91. Section 34-53-00 Altitude Alerting Device .) CASA granted a waiver against FAR 25.1441(c) and (d) (a)(1) Flight Crew Member On-Demand Mask.523 Emgcy Equip. Manual Means of Deployment SSR Transponder and Altitude Reporting Equipment Dual Mode S Transponders meeting ARINC 718 fitted as standard – See Boeing Detailed Spec. A/c 91.545 A.1305(a)(6) * (9) Oil Temperature N/A – Turbojet (10) Manifold Pressure N/A – Turbojet (11) Cylinder Head Temp. – Supplemental O2 Masks for all Pax/Crew Note: After evaluation of the requirements by Pacific Blue it – Supplemental Mask in Washroom/Toilet was determined an additional two 311 litre capacity oxygen Above FL300 – Total Outlets Exceed Pax by 10% bottles were needed.851(a)(1) & (7).1331(a) (3) Gyro Power Supply FAR 25. §25-64-20 NOTE: For details of emergency equipment on VB aircraft see VB Engineering Order EO 25-139 Emergency Locator Transmitter – TSO C126 406 MHz To be determined on an individual aircraft basis (Artex P/N 453-0004 [Commercial Model B406-1. Section 34-51-00 navigation equipment Dual DME meeting ARINC 709 fitted as standard – See Detailed Spec.1303(a)(2)/§31-25-00 (6) Time in hr/min/sec FAR 25.1303(b)(2) ** (3) Altimeter FAR25.729(e) (13) U/C Position See Det. (See Virgin Blue EO 25-159 Issue 1) Auto Presented > FL140. 15 min PBE Three independent oxygen systems are fitted as standard – See (2) 1 Set of Portable 15 min PBE Detailed Spec.1351(6) (14) Ammeter/Voltmeter * Engine parameters and indicators shown on the engine display unit – See Detailed Spec. except as noted: Civil Aviation Rules Part 91 Subpart F . Spec. safety belts fastened FAR 25.505 91. System designed to provide supply for emergency (5) Min Quantity Supplement Oxygen descent as per specified descent profile (12 minutes) (6) Required Supplemental/Therapeutic Oxygen Protective breathing of 300 l/crew member provided Above FL250 – Quick-Donning Crew On-Demand Mask Crew system has 39 cu. >10 pax. 91. §33-24-00 N/A – Turbojet (8) Coolant Temp FAR 25.791 – See Detailed Spec.1303(b)(6) (2) Gyroscopic DI See Detailed Spec. §34-23-20 FAR 25.1381/ §33-13-00 Single HF (ARINC 716) fitted as standard – See Detailed Spec.Pax. §25-11-10 FAR Part 25 para §25.1401/§33-44-00 FAR 25. Spec.1303(a)(3) (4) Magnetic Compass See Det.See Boeing Detailed Spec. Section 34-55-00 Single ADF meeting ARINC 712 fitted as standard .517 IFR 91. Spec.§34-57-00 (Also states there are partial provisions for a second ADF system) Dual IRS and ADIRU meeting ARINC 704 fitted as standard – See Detailed Spec. §23-11-00 Dual VHF (ARINC 716 or 750) fitted as standard – See Detailed Spec.1303(b)(1) ** (1) ASI FAR 25.543 91. §28-41-00 FAR 25. §25-64-40 (c) More than 61 pax – Portable Megaphones per Table 9 Fitted as Standard . Section 34-58-00 (a) More than 10 pax – First Aid Kits per Table 7 Fitted as Standard – See Boeing Detailed Spec.Type Acceptance Report Compliance with the following additional NZ operating requirements has been reviewed (for the Models 737-8FE/-8BK) and were found to be covered by either the original certification requirements or the basic build standard of the aircraft.519 91.1305(a)(4) * (7) Oil Pressure MEANS OF COMPLIANCE: FAR Part 25 para §25.1303(b)(1) ** (2) Machmeter FAR 25.15 (1)Turn and Slip (2) Position Lights VFR Comm. of Halon must be used to replace a water fire extinguisher.1303(b)(3) (8) Rate of Climb/Descent FAR 25.507 91.535 Press.699(a) (12) Flap Position See Det. FAR 25.1305(c)(3) * (6) Engine RPM FAR 25.785 – See Detailed Spec. §31-62-12 and §77-00-00 ** Flight data displayed in EFIS/Map format on EFIS display unit – See Detailed Spec. Spec. Four portable cylinders installed in (3) Crew Member – Pax O2 Mask. provision for SATCOM and ACARS FAR 25. Spec.010 and Fig. §25-64-10 – Fire Extinguishers per Table 8 Fitted as Standard – See Boeing Detailed Spec.529 91.1303(a)(1)/§34-21-50 (5) OAT EFIS Detailed Spec.1303(b)(2) (4) Sensitive Altimeter IFR communication and Dual VOR meeting ARINC 711 fitted as standard – See Detailed Spec. §31-62-32 NOTE: Unless otherwise specified all reference to Detailed Specification means Document D6-38808-18 91511 Night 91.Turbojet or Turbofan Fitted as standard – See Detailed Spec. §34-23-10 (1) Gyroscopic AH FAR25. Flight Training Pax Information Signs – Smoking. §35-00-00. §30-30-00 (7) ASI/Heated Pitot FAR 25. ft.513 91.Volume/Pressure/Delivery FAR Part 25 paragraphs §25.§26-26-00 NOTE: The VB aircraft specification is for four Halon 1211 extinguishers instead of the standard Boeing fit of three Halon and one water. §32-60-00 FAR 25.25-2 (Five portable bottles fitted on 737-8FE – See DS §25-64-60) (4) Spare Oxygen Masks/PBE . Landing Light. and in addition no water type are fitted.377 121. Intercom Meets FAR §121. The fire extinguishers fitted were BFE and were not Boeing approved. Operational requirement – compliance as applicable Operational requirement – compliance as applicable (Four 56-person liferafts are fitted as standard on 737-8FE aircraft – See Doc.See Boeing Detailed Spec.) P/A.) 4. §34-43-00 TSO C63 (Rockwell P/N 622-5132-106 fitted as BFE on ILFC aircraft. Spec. 5&6.Type Acceptance Report Civil Aviation Rules Part 121 Subpart F .) 3. (These are acceptable in NZ under Part 21 Appendix D. Alt.2(a)(3). placarding and cabin attendant procedures to ensure screens are stowed for takeoff and landing. However the video screen did not comply with FAA requirements or NZCAR Part 26 D.355 121.344 Appendix M [88 parameters] effective 12. Boeing Letter reference B-H340-09-01295 provides system details to show compliance with NZCAR §91. Rev. §31-31-10 requires TSO C124 68 parameters recorded – See Detailed Spec. §31-62-34 Weather Radar – Appendix B.See Boeing Detailed Spec.361 121.3 : 16 September 2009 9 TAR 1/21B/2 — Boeing 737-800 . Jetconnect elected to disable the seat back recline lockout system.359 121. Key (3) Door to emergency exit Night Flight .375 121.357 121. Light in each pax cabin IFR Operations Speed.379 REQUIREMENT: MEANS OF COMPLIANCE: Additional Instruments (Powerplant) Additional Equipment . (FAA AC 25-17 guidelines require that at least one fire extinguisher appropriate for a Class A fire should be provided. D019A001VOZ38P-1 §25-62-20) Emergency Equipment Per §91. The CAA requested a technical justification for acceptance of the headsets in NZ. §25-68-00 Protective Breathing TSO C99 cockpit equipment (Scott MC10-25 mask fitted as BFE on ILFC aircraft.) Oxygen System NZCAR Compliance The passenger oxygen system uses chemical oxygen generators.8 requires Wx meeting ARINC 708 fitted as standard – See Detailed Spec.207(d)(1).) Boeing confirmed 737-800 are equipped at production for compliance with FAR 121. 2003) for the issue of the export certificate of airworthiness.371 121.Instrument and Equipment Requirements PARA: 121.) Flight Data Recorder – Appendix B. Because of the time frame involved the applicant elected to re-fit the standard Boeing headsets. Seat belt extension with supplementary baby loop. The FAA required a waiver from CASA against various FARs (See letter dated April 18. §23-70-00 requires TSO C84/C123 (Allied Signal P/N 980-6020/22-001 fitted as BFE on ILFC and VB aircraft. Acceptance of FAA STCs.369 121. §33-42-10 and 33-20-00.) Additional Attitude Indicator Fitted as standard – See Boeing Detailed Spec.97.523 and EROPS kit Operational requirement – compliance as applicable Fitted as standard .367 121.365 121.6 DFDR meeting ARINC 747 fitted as standard – See Detailed Spec.09. (See Certification Review Item D-1. which are not FAA Approved. (YJ865-66 also comply with NPRM 99-19 [91 parameters] although this was not made a Rule.363 121.(1) Windscreen Wiper (2) Door. §35-30-00 TSO C115 cabin equipment (Puritan Bennett P/N 119003 fitted as BFE on ILFC aircraft.5 CVR meeting ARINC 757 fitted as standard – See Detailed Spec.2. §25-18-00 Not Applicable – No doors between passenger compartments Fitted as standard – See Det.9 requires TSO C92 GPWS meeting ARINC 723 fitted as standard – See Detailed Spec. This was accepted in NZ as an Equivalent Safety Finding based on the ease of retraction. as follows: 1&2. Installed to meet Australian rules and acceptable in New Zealand under NZCAR §91. §31-31-20 (Allied Signal P/N 980-4700-042 fitted as BFE on ILFC and VB aircraft.535.373 121.) GPWS – Appendix B.318 and 319 See Detailed Spec. §30-43-00 Fitted as standard – See Boeing Detailed Spec. Exit row seat recline over-ride and video screen tilt back.) Equipment (PBE) Fitted as standard . §23-31-00 (PA) and §23-51-00 (Intercom) NOTE: The standard VB Specification calls for Sennheiser HME1410KA boom mic headsets. Cockpit Voice Recorder – Appendix B. spare bulbs/fuses Flights over water Liferafts FAR Part 25 is a Part 21 Appendix C standard Fitted as standard – See Boeing Detailed Spec. §34-46-00 Certification Issues Model 737-838: CASA Delivery Waivers The first three aircraft YL566-568 were delivered in the QANTAS configuration with six exceptions for which CASA granted a waiver. These included: 1...562. Boeing developed an AMOC for showing compliance with FAR§25. which addresses FAA policy on the stowage. The exit row outside armrest mounting stub was deemed a hazard because it was within the 35 inch head strike arc.. but this was not completed in time. A cover piece was manufactured and secured in place with tie-wraps. 4... (The aircraft still complies with FAR §121.... YL566-568 were originally intended for delivery with seats meeting FAR §25.3 : 16 September 2009 . 3..Type Acceptance Report FAA Cabin Configuration Approval There were a number of issues identified by the FAA during the certification of the cabin interior. 2.. David Gill Team Leader Airworthiness ……………………………. then the physical characteristics of the installation shall meet minimum defined criteria.. which involves ensuring that if the monitor does not fully move out of the head strike path with a force or 10 pounds or less. which required rectification action. The FAA published Memorandum 02-115-21. retention. Checked – Peter Gill Airworthiness Engineer Appendix 1 List of Type Accepted Variants: Model: Applicant: 737-8Q8 737-8FE 737-8BK 737-838 Polynesian Limited Pacific Blue Airlines (NZ) Ltd Pacific Blue Airlines (NZ) Ltd Jetconnect Limited TAR 1/21B/2 — Boeing 737-800 CAA Work Request: 1/21B/2 4/21B/9 4/21B/20 9/21B/15 10 Date Granted: 14 November 2000 13 January 2004 26 February 2004 16 September 2009 Rev. It was padded with a minimum of an inch of ensolite. A potential finger pinch hazard was identified under the economy class seat armrest.) Attachments The following documents form attachments to this report: Photographs first-of-type variant 737-8FE s/n 33796 ZK-PBA Three-view drawing Boeing Model 737-800 “NG” Copy of FAA Type Certificate Data Sheet Number A16WE Sign off ……………………………………. and breakaway of deployable individual video systems (IVS) installed in transport airplane seats... On YL566-568 the Business Class Seat Video Monitors and Arms did not meet this guidance and were not padded.311(j) by date-of-manufacture.785(k).. Rush Revision RR97164-42 replaced the inflatable seat belts with standard items and amended the seat dataplate.. dated 21/11/02.