As NZS 3679.2-2010 Structural Steel Welded I Sections

AS/NZS 3679.2:2010 AS/NZS 3679.2:2010 Australian/New Zealand Standard™ This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. Structural steel Part 2: Welded I sections AS/NZS 3679.2:2010 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee BD-023, Structural Steel. It was approved on behalf of the Council of Standards Australia on 28 October 2010 and on behalf of the Council of Standards New Zealand on 5 November 2010. This Standard was published on 26 November 2010. The following are represented on Committee BD-023: Austroads Australian Chamber of Commerce and Industry Australian Industry Group Australian Steel Association Australian Steel Institute Bureau of Steel Manufacturers of Australia Business New Zealand Steel Construction New Zealand The University of New South Wales The University of Sydney This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. Keeping Standards up-to-date Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Web Shop at www.saiglobal.com.au or Standards New Zealand web site at www.standards.co.nz and looking up the relevant Standard in the on-line catalogue. For more frequent listings or notification of revisions, amendments and withdrawals, Standards Australia and Standards New Zealand offer a number of update options. For information about these services, users should contact their respective national Standards organization. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Please address your comments to the Chief Executive of either Standards Australia or Standards New Zealand at the address shown on the back cover. This Standard was issued in draft form for comment as DR 07235. AS/NZS 3679.2:2010 Australian/New Zealand Standard™ This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. Structural steel Part 2: Welded I sections Originated in Australia as AS 3679.2—1991. Jointly revised and designated AS/NZS 3679.2:1996. Third edition 2010. COPYRIGHT © Standards Australia Limited/Standards New Zealand All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher, unless otherwise permitted under the Copyright Act 1968 (Australia) or the Copyright Act 1994 (New Zealand). Jointly published by SAI Global Limited under licence from Standards Australia Limited, GPO Box 476, Sydney, NSW 2001 and by Standards New Zealand, Private Bag 2439, Wellington 6140 ISBN 978 0 7337 9734 7 AS/NZS 3679.2:2010 2 PREFACE This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee BD-023, Structural Steel to supersede AS/NZS 3679.2:1996. The objective of this Standard is to specify requirements for welded I sections for general structural and engineering functions. These functions include the possibility of such welded I sections being subjected to dynamic and other special loads. The contents of this edition align with: AS 3597 This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. Structural and pressure vessel steel—Quenched and tempered plate Structural steel hollow sections Structural steel—Hot-rolled plates, floorplates and slabs Structural steel Part 1: Hot-rolled bars and sections AS/NZS 1163 3678 3679 3679.1 This edition incorporates the following major changes to the previous edition: (a) (b) (c) (d) (e) (f) Redundant grades 250, 250L0, 250L15, 350, 350L0 and 350L15 have been removed. The mandatory requirement for test reports and test certificates to be performed by third-party accredited laboratories. The introduction of mandatory minimum information required on test certificates. The inclusion of Appendix B on product conformity as a mandatory provision for conformance with this Standard. The web-to-flange testing frequency has been revised and moved to Appendix B Section dimensions has been moved to the new Appendix C. To permit the steel industry time to adjust to the new edition of the Standard, the 1996 edition of AS/NZS 3679.1 will remain ‘available superseded’ and will be withdrawn 12 months from the date of publication of this Standard. A statement expressed in mandatory terms in a note to a table is deemed to be a requirement of this Standard. The terms ‘normative’ and ‘informative’ have been used in this Standard to define the application of the appendix to which they apply. A ‘normative’ appendix is an integral part of a Standard, whereas an ‘informative’ appendix is only for information and guidance. 3 AS/NZS 3679.2:2010 CONTENTS Page SCOPE........................................................................................................................ 4 NORMATIVE REFERENCES ................................................................................... 4 DEFINITIONS............................................................................................................ 5 DESIGNATION.......................................................................................................... 6 MATERIALS.............................................................................................................. 6 MANUFACTURING PROCESS ................................................................................ 6 MANUFACTURING TOLERANCES........................................................................ 7 MECHANICAL TEST REQUIREMENTS................................................................. 8 WELD QUALITY, TESTING AND EXAMINATION .............................................. 8 IDENTIFICATION, CERTIFICATION AND INDEPENDENT TESTS.................... 8 ROUNDING OFF NUMBERS ................................................................................... 9 1 2 3 4 5 6 This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. 7 8 9 10 11 APPENDICES A PURCHASING GUIDELINES.................................................................................. 15 B PRODUCT CONFORMITY...................................................................................... 17 C DIMENSIONS........................................................................................................... 19 D MEASUREMENT OF CAMBER AND SWEEP IN WELDED I SECTIONS .......... 22 E WELDED SECTIONS FOR FRACTURE CRITICAL APPLICATIONS ................. 23 BIBLIOGRAPHY .................................................................................................................... 24 AS/NZS 3679.2:2010 4 STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Australian/New Zealand Standard Structural steel Part 2: Welded I sections 1 SCOPE This Standard specifies requirements for the production and supply of welded I sections for general structural and engineering purposes. This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. This Standard does not cover the following: (a) (b) (c) (d) (e) (f) (g) (h) Structural steel—Hot-rolled bars and sections. Steel plates for pressure equipment. Structural steel—Hot-rolled plates, floorplates and slabs. Carbon steels and carbon-manganese steels—Hot-rolled bars and semifinished products. Structural steel hollow sections. Steel reinforcing bars for concrete. Structural and pressure vessel steel—Quenched and tempered plate. Built-up I sections fabricated in accordance with AS 3990, AS 4100 or NZS 3404. NOTE: Guidelines to purchasers on requirements that should be specified by the purchaser and those that should or may be agreed on at the time of enquiry and order are specified in Appendix A. Product conformity with this Standard is specified in Appendix B. For New Zealand only, additional requirements for welded steel sections for fracture critical applications are specified in Appendix E. 2 NORMATIVE REFERENCES The following documents are indispensable for the application of this Standard: NOTE: References for informative purposes are included in the Bibliography. AS 1365 1391 2706 Tolerances for flat-rolled steel products Metallic materials—Tensile testing at ambient temperature Numerical values—Rounding and interpretation of limiting values AS/NZS 1554 Structural steel welding 1554.1 Part 1: Welding of steel structures 3678 NZS 3404 3404.1 Structural steel—Hot-rolled plates, floor plates and slabs Steel structures Standard Part 1: Materials, fabrication, and construction COPYRIGHT This is a free preview. Purchase the entire publication at the link below: AS/NZS 3679.2:2010, Structural steel Welded I sections This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com. Looking for additional Standards? Visit SAI Global Infostore Subscribe to our Free Newsletters about Australian Standards® in Legislation; ISO, IEC, BSI and more Do you need to Manage Standards Collections Online? Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation Do you want to know when a Standard has changed? Want to become an SAI Global Standards Sales Affiliate? Learn about other SAI Global Services: LOGICOM Military Parts and Supplier Database Metals Infobase Database of Metal Grades, Standards and Manufacturers Materials Infobase Database of Materials, Standards and Suppliers Database of European Law, CELEX and Court Decisions Need to speak with a Customer Service Representative - Contact Us