e-Fim ANM2000Broadband Access Network Management System Installation Manual (Based on Windows) Version: B Code: MN000000366 FiberHome Telecommunication Technologies Co., Ltd. July 2010 Thank you for choosing our products. We appreciate your business. Your satisfaction is our goal. We will provide you with comprehensive technical support and after-sales service. Please contact your local sales representative, service representative or distributor for any help needed at the contact information shown below. Fiberhome Telecommunication Technologies Co., Ltd. Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China Zip code: 430073 Tel: +86-27-87691549 Fax: +86-27-87691755 Website: http://www.fiberhomegroup.com . All rights reserved No part of this document (including the electronic version) may be reproduced or transmitted in any form or by any means without prior written permission from FiberHome. (Hereinafter referred to as FiberHome) All brand names and product names used in this document are used for identification purposes only and are trademarks or registered trademarks of their respective holders..Legal Notice TM TM TM are trademarks of FiberHome Telecommunication Technologies Co. Information in this document is subject to change without notice. Ltd. . . 07. This manual describes the installation methods of the ANM2000 with the version Build05. which can perform the effective and unified management of multiple types of broadband access equipment developed by FiberHome.xx. Relevant Manuals Manual e-Fim ANM2000 Broadband Access Network Management System Operation Manual (Based on Description This manual describes the ANM2000 common operations and maintenance methods for the purpose of helping users know the ANM2000 further and operate it well.05. Windows) I .Preface The ANM2000 is an integrated broadband access management platform developed by FiberHome. Corresponds to the Informix 11.Version Version Instruction A The initial version.0R2 Build05. B Intended Readers This manual is intended for the following readers: Commissioning engineers II Construction engineers FiberHome engineers . Compared with version A. and the FAQ is added.05.07.5 version. and the ANM2000 V3. the installation methods of the Informix are modified.xx version. Caution Warning Possible injury to persons or systems. May cause severe bodily injuries. developed by IBM ANM2000 Informix Symbol Conventions Symbol Refer to Meaning Note Important features or operation guide. or cause traffic interruption or loss. III .Conventions Terminology Conventions Terminology Meaning FiberHome e-Fim ANM2000 Broadband Access Network Management System The database software used together with the ANM2000. . .. 3-2 3.........................................1........... III 1 Overview ....................... 2-16 2. 1-2 1..... 3-2 3...................................Contents Preface ....................................1 Requirements of Hardware Configuration ................. 3-11 3.............................................4 Starting the Service ..........1 Initial Installation ....................................... II Conventions ......1............................1 Running the ANM2000_Server Installation Package..........5 Dynamic Database ............................1 Installation of the Informix11........ 3-10 3..............................................................................3 Setting of the Environment Variables ...............................................2 Installation of the Server End ................................................................................ 2-2 2...................................... 2-25 Installation of the ANM2000 ..............................3 2 3 1...2..............................................................2 Verifying the ANM2000’s Client End Installation................................................2 Creating the Tablespace.............................................. 1-1 1..................3.......1................ 3-7 3.......................5 Verifying the ANM2000’s Server End Installation ....................................1...................... 1-4 1..........................2.... 3-11 3................................................ 1-2 1..................................... II Intended Readers ..... 2-11 2.......................... 2-1 2................3..3 Initializing the Table Architecture ...................................1....2 Requirements of Software Configuration..................4 Verifying the Informix Database Installation ..................1 Running the ANM2000_Client Installation Package ..... 1-3 Installation Flow Diagrams . 3-15 ................................2 Installation of the Informix Client-SDK..................................... 3-10 Installation of the Client End ..............1 3................................................................................1 Working Mode ................ 3-1 3........ 1-4 1..2 Configuration Requirements .................................2 Upgrade .........2............................. 1-5 Installation of the Informix Database ..................................................... 1-2 1.....2................. 3-9 3..... I Relevant Manuals ... I Version ....... ...... 4-4 4. 4-9 4.................. 4-11 4................ 4-2 4.....1 Preparation before the Upgrade Operation ............2..... 4-9 4......1.......1................... 4-6 4.. 4-2 4......1 How to Handle the Invalid Configuration File ..........1 Preparation before the Upgrade Operation ..................................................1...........2.................3 Backup of the Software Package .... 5-6 5.......... 4-3 4............. 5-6 5.............. 5-1 5.. 4-8 The Upgrade of the Client End..........4 Uninstalling the Current ANM2000 ...................5 Installing the ANM2000 of the Upgrade Version ...... 4-7 4............4 How to Handle the Informix Database Not Installed . 5-2 5...............................................3 Installing the Client End with the Upgrade Version.................. 5-9 5...........8 Checking the Configuration Data ....... 5-8 5.....7 Verifying the Upgraded Software Version ...............................4 Verifying the Upgraded Software Version ....1 4...... 4-11 FAQs .............1................................... 4-1 4......4 Upgrade of the ANM2000 .............8 How to Handle the Data Exporting / Importing Failure .......2.................. 5-10 ...2............1....6 Importing the Configuration Data ....2 How to Handle the Long-Period No Response from the ANM2000 5-4 5..........5 How to Handle the Connection Failure of the ANM2000 ............1...... 4-2 4................. 5-5 5.........6 How to Handle the Tablespace Creation Failure ....7 How to Determine the IP Address Bound with the Database ...2 Uninstalling the Current Client end..2 Backup of the Original Configuration Files ............2 5 The Upgrade of the Server End ............ 4-9 4.......................... 4-5 4...................................................3 How to Handle the Inadequate Disk Space ...............................................1.........1................ 1-6 Figure 1-4 The flow of upgrading the Client end .... 2-16 Figure 2-3 Setting the Informix user password ................................................. 2-18 Figure 2-5 Setting the INFORMIXSERVER ............... 3-8 Figure 3-2 The status of the successful creation of the tablespace ................................................... 2-21 Figure 2-7 Creating system variables (2) .. 2-17 Figure 2-4 Setting the INFORMIXDIR .................. 2-26 Figure 3-1 Creating the tablespace ........... 2-23 Figure 2-10 The status of the normal starting of the database .................................................................................. 3-9 ....................................................................................... 2-25 Figure 2-11 The valid status of the configuration file ...... 1-5 Figure 1-3 The flow of upgrading the Server end ............................. 3-8 Figure 3-3 Initializing the Table architecture ...................... 2-8 Figure 2-2 The Server Information tab......................................................................................... 3-9 Figure 3-4 The status of the successful initialization of the Table architecture ........................ 2-19 Figure 2-6 Creating system variables (1) ................................................................................................................................................ 1-4 Figure 1-2 The flow of installing the Client end for the first time ....... 2-21 Figure 2-8 Modifying the ROOTSIZE ........................ 2-23 Figure 2-9 Modifying the LOGFILES .....Figures Figure 1-1 The flow of installing the Server end for the first time .............................. 1-7 Figure 2-1 The status that the port 6000 is occupied ........................................................................................................................................... . .......... 2-8 Table 5-1 Parameter values in the ONCONFIG file ................... 1-3 Table 2-1 The database user information............................................................... 2-6 Table 2-2 The database parameters ........... 2-7 Table 2-3 The store location information .... 5-5 ............................................... 5-4 Table 5-2 The parameters for creating the tablespace .................. 1-2 Table 1-2 Requirements of hardware configuration on the Client end............................................................................................................Tables Table 1-1 Requirements of hardware configuration on the Server end ........... . and to install the software matching the working mode.1 Overview Before installing the ANM2000. you need to be familiar with the ANM2000’s working mode. This chapter includes the following contents: Working mode Configuration requirements Installation flow diagrams Version: B 1-1 . so as to ensure that the installation can be completed successfully. the space of drive D should be not less than 15 GB 2*146GB.93 GHz 4 8G DDR3 (UDIMM). or respectively on two computers. connected with the full-configuration ONUs 1-2 CPU Clock Rate CPU Number Memory Intel® Xeon® processor X7460. the ANM2000 uses the Client end-Server end working mode.2 Configuration Requirements 1.1 Working Mode At present. When the network maintenance engineers are far from both the access equipment and the network management system server. 1. When both the Client end and server end are installed on a computer.2. 2. 1333 MHz Intel® Xeon® processor X7350. connected with the full-configuration ONUs 100 to 200 OLTs. the space of drive D should be not less than 73 GB 2*146GB. the space of drive D should be not less than 5 GB Harddisk Format Both drive C and drive D use the NTFS format Both drive C and drive D use the NTFS format Both drive C and drive D use the NTFS format NIC Embedded NC326i PCI Express bi-port GE server adaptor Embedded NC326i PCI Express bi-port GE server adaptor Embedded HP NC107i PCI-Express bi-port GE server adaptor Version: B . 1333 MHz 2 4G DDR3 (UDIMM). In this case. the ANM2000’s Client end and Sever end can be installed on one computer. Table 1-1 Requirements of hardware configuration on the Server end Network Scale 200 to 500 OLTs. 2. connected with the full-configuration ONUs Less than 100 OLTs. this is also called a stand-alone mode. this Client end-Server end working mode can be used to access the server via the Client end for achieving the purpose of managing the equipment.1 Requirements of Hardware Configuration The requirements of the hardware configuration for the ANM2000’s Server end depend on the network scale. 1333 MHz Intel® Xeon® processor E5506. 3 GHz Harddisk Space 2*300 GB.66 GHz 4 16G DDR3 (UDIMM). The detailed requirements are listed in Table 1-1.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 1. Windows Vista. 1333 MHz 2® 2® Harddisk Space 250 GB. connected with the full-configuration ONUs Intel® Core processor.2 CPU Number Memory 1 4G DDR3 (UDIMM). 1333 MHz 1 2G DDR3 (UDIMM). 1333 MHz 1 1G DDR3 (UDIMM). Windows2008. Windows2003server. Table 1-2 Requirements of hardware configuration on the Client end Network Scale CPU Clock Rate 200 to 500 OLTs.2. connected with the full-configuration ONUs Intel® Core processor. The operator has assigned a fixed IP address for the network management system and configured this IP address for the computer. the space of drive D should be not less than 15 GB 250 GB. or Windows7 operating system has been installed on the computer. 2 GHz 100 to 200 OLTs. 2 GHz 1. The software configuration of the computer acting as the ANM2000’s Client end should meet the following requirements: Version: B The legal Windows XP. the space of drive D should be not less than 15 GB 250 GB.1 Overview The requirements of the hardware configuration on the ANM2000’s Client end are listed in Table 1-2. Windows2003. 1-3 . The operating system must be 64-bit. 2 GHz Less than 100 OLTs. the space of drive D should be not less than 15 GB Harddisk Format Display Card Both drive C and drive D use the NTFS format 32M video memory Both drive C and drive D use the NTFS format 32M video memory Both drive C and drive D use the NTFS format 32M video memory Requirements of Software Configuration The software configuration of the computer acting as the ANM2000’s Server end should meet the following requirements: The legal Windows XP professional SP2. connected with the full-configuration ONUs Intel® Core 2® processor. or Windows2008 standard operating system has been installed on the computer. 3. If some problems arise during the installation.1 Initial Installation Installing the Server end for the first time When you install the ANM2000’s Server end for the first time. please refer to the installation flow illustrated in Figure 1-1. Figure 1-1 The flow of installing the Server end for the first time 1-4 Version: B .e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 1. please refer to Chapter 5 FAQ.3 Installation Flow Diagrams 1. please refer to Chapter 5 FAQ.1 Overview Installing the Client end for the first time When you install the ANM2000’s Client end for the first time. please refer to the installation flow illustrated in Figure 1-3. Figure 1-2 The flow of installing the Client end for the first time 1.2 Upgrade Upgrading the Server end When it is necessary to upgrade the ANM2000’s Server end. Version: B 1-3 1-5 . If some problems arise during the installation.3. please refer to Chapter 5 FAQ. If some problems arise during the installation. please refer to the installation flow illustrated in Figure 1-2. e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) Figure 1-3 The flow of upgrading the Server end 1-6 Version: B . please refer to the installation flow illustrated in Figure 1-4. Figure 1-4 The flow of upgrading the Client end Version: B 1-3 . If some problems arise during the installation. please refer to Chapter 5 FAQ.1 Overview Upgrading the Client end When it is necessary to upgrade the ANM2000’s Client end. . 2 Installation of the Informix Database The ANM2000 of the V3. This chapter introduces the installation and setting methods of the Informix11.07.0 build 05.5 database.05.5 database.04. if you use the ANM2000 of the V3. This chapter includes the following contents: Installation of the Informix11.02 version is used together with the Informix11.07.5 dynamic database Installation of the Informix Client-SDK Setting of the environment variables Verifying the Informix database installation Version: B 2-1 . please install the Informix9.4 database.xx.0 build 05. Before installing the ANM2000. The operator has assigned a fixed IP address for the network management server. 2-2 to make the Welcome dialog box appear. Run the installation file. Operation steps 1.5 Dynamic Database The ANM2000 is used together with the Informix database. Version: B . and click Next. Double-click 2.1 Installation of the Informix11. please install the Informix database first. Prerequisites The hardware and software configuration of the server should meet the requirements instructed in Section 1.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 2.2 Configuration Requirements. Select the components to be installed. you need to install the dynamic database and the Client-SDK. so select IBM Informix Dynamic Server 11. 4. Click Next to confirm the installation operation. 2-3 .2 Installation of the Informix Database In this case. Version: B Accept the software agreement.50 and click Next.50 with J/Foundation and IBM Informix Client-SDK 3. Confirm to install the Informix dynamic database. 3. 5. and then click Next.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) Select I accept the terms in the license agreement. 2-4 Version: B . Select the installation mode. so please select Custom and then click Next. The operator must install the software in Custom mode. According to the default setting. 7. Set the installation path. you should install all properties by clicking Next. set the installation path as C:\Informix. In this case. Then click Next. you also can install the database on other disks. Here we take the installation on disk C as an example. Version: B 2-5 . Select the database properties to be installed.2 Installation of the Informix Database 6. e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 8. Table 2-1 The database user information Parameter Item Recommended Value Install Domain(requires Informix user) Clear Start database server as Local System User Clear Do not create user Informix account Clear Password Anms2k Confirm Password Anms2k Enable Role Separation for auditing procedures Clear Note: You can set the database user password on demand. Such password must be formed by uppercase letters. lowercase letters and numbers. Set the database information. 2-6 Version: B . 1) Set the database user information according to Table 2-1. and then click Next. In this manual. otherwise the ANM2000 cannot be used correctly. Select Initialize Server Enable a custom configuration file to suit your needs and hardware Enable DRDA Support Clear Service Name turbo Port 6000 Server number 0 Clear Clear Caution: The internal database service name and port No. Table 2-2 The database parameters Parameter Item Server Name Create Server Recommended Value Commonly its value is the computer name along with the prefixed ol_. please set them correctly. we take ol_test as an example for the description. Version: B 2-7 . of the ANM2000 are respectively turbo and 6000.2 Installation of the Informix Database 2) Set the database parameters according to Table 2-2. and we recommend that you modify it to the project name (such as ol_zjyd). and then click Next. you need to delete the man 6000/tcp item. you can open the services file under C:\\ windows \ system32 \ drivers \ etc to delete the corresponding item. Table 2-3 The store location information Parameter Item DB Space Name Location for data dbspace IDS Location for smart large object data 2-8 Primary Data Location Mirror Data Location (optional) Size (MB) Recommended Value It should be the same as the set Server Name.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) Note: If turbo and 6000 are occupied. As Figure 2-1 shows. Figure 2-1 The status that the port 6000 is occupied 3) Set the data store location information according to Table 2-3. D Null 200 SB Space Name sbspace Primary Data Location Mirror Data Location (optional) Size(MB) D Page Size (in pages) 1 Null 200 Version: B . and then click Next. 2 Installation of the Informix Database 9. click Next to start installing the Informix database. Version: B 2-9 . Confirm the settings and start the installation. After confirming that the settings are correct. the installation of the Informix database is completed. 2-10 Version: B . Complete the installation. In this case. click Finish to start installing the Informix Client-SDK.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 10. After completing the installation. 2 Installation of the Informix Database 2.50 Setup dialog box appear. click Finish to make the IBM Informix Client-SDK 3. After the Informix database is installed. Operation steps 1. the system will automatically enter the installation programme of the Informix Client-SDK. Version: B 2-11 .2 Installation of the Informix Client-SDK The Informix Client-SDK is used to establish the connection from the client end to the database server. Confirm the installation. click Next to confirm to install the Informix Client-SDK. Prerequisites The Informix database has been installed. In this dialog box. After the database is installed. Accept the software agreement.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 2. 3. and then click Next. and then click Next. 2-12 Version: B . Set your personal information. select I accept the terms in the license agreement. Set the personal information. In the License Agreement dialog box. Set the installation path. which should be identical with that of the Informix database.2 Installation of the Informix Database 4. Version: B 2-13 . Click Change to set the installation path of the Client-SDK. you must select Custom. Select the installation type. 5. and then click Next. For the installation type. and then click Next. Install the Client-SDK. then click Next. 1) 2-14 Click Install to start installing the Client-SDK.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 6. Select the components to be installed. It is recommended to use the default settings. 7. Version: B . In this case. 3) Clear Launch VSAI Installer. Version: B 2-15 . and then click Finish to complete the installation.2 Installation of the Informix Database 2) Click Next. the installation of the Informix Client-SDK is completed. Operation steps 1. Figure 2-2 The Server Information tab 2-16 Version: B . 1) Select Start → All Programme → IBM Informix Client-SDK 3. 2) In the Informix setnet32 dialog box. HostName should be set to the IP address to be bound with the database. so as to use the Informix database normally. Set the environment variables.3 Setting of the Environment Variables After installing the Informix database. Prerequisites The Informix database and the Informix Client-SDK have been installed. select the Server Information tab (as shown in Figure 2-2). then click Make Default Server and click Apply to make the configuration valid.50 → setnet32 to open the Informix setnet32 dialog box. you need to set the relevant variables.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 2. If the server is configured with dual NIC. 2-17 . and set the user password of the Informix. such as Anms2k. In this case.2 Installation of the Informix Database 3) Select the Host Information tab. Then click Apply. this password should be the same as the password set for the installation of the Informix database. Figure 2-3 Setting the Informix user password Note: If you do not select Server Information but select Host Information directly，the Current Host item will be empty. you can select the Server Information tab first and the Host Information tab second. 4) Version: B Click OK to open the IBM Informix Setnet dialog box. as shown in Figure 2-3. and then click OK. and then the Current Host item will read the default values automatically. and then click Set and then Apply to make the configurations valid. select Use my settings. Figure 2-4 Setting the INFORMIXDIR After completing the settings. and set it to C:\Informix.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 5) Select the Environment tab. 2-18 Version: B . In this tab. as shown in Figure 2-4. select the INFORMIXDIR= item. 2 Installation of the Informix Database 6) Select the INFORMIXSERVER= item. and then click Set and then Apply to make the configurations valid. and set it to the default value in the drop-down list of the Edit Environment Variable combo box. select Use my settings. Figure 2-5 Setting the INFORMIXSERVER After completing the settings. Version: B 2-19 . Then click OK. as shown in Figure 2-5. in the System window. select Advanced System Settings. and in the System Properties dialog box. and select Properties. Version: B . select Advanced.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 7) 2-20 Right-click Computer. Figure 2-6 Creating system variables (1) Figure 2-7 Creating system variables (2) Version: B 2-21 . In the System Variables pane of the Environment Variables dialog box. as shown in Figure 2-6 and Figure 2-7. click Create to create INFORMIXDIR and INFORMIXSERVER.2 Installation of the Informix Database 8) Click Environment Variables. the values of the two items should be the same as those in the Informix setnet32 dialog box. e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 9) 2-22 Click OK to finish the setting, as shown in the following figure. Version: B 2 Installation of the Informix Database 2. Modify the configuration file. Use the notebook to open the etc \ ONCONFIG. Instance name file under the Informix installation directory (such as the ONCONFIG.ol_test file), and modify the ROOTSIZE value to 1024000 (see Figure 2-8) and the LOGFILES value to 40 (see Figure 2-9). After the modification is completed, save the configuration file and then exit. Figure 2-8 Modifying the ROOTSIZE Figure 2-9 Modifying the LOGFILES Version: B 2-23 e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 3. Start the service. 1) Right-click Computer, and select Manage to open the Server Manager window; in this window, select Configuration -> Services. 2) Double-click the Informix IDS service, and input –iy in Start Parameter; then click Start. After the start operation, please confirm that the service has been started. 2-24 Version: B If the system displays On Line. Figure 2-10 The status of the normal starting of the database Version: B 2-25 .2 Installation of the Informix Database 2. 1. Input onstat -.4 Verifying the Informix Database Installation Prerequisites The Informix database has been installed.50 → ol_test to open the ol_test window. this indicates that the database has been started normally. 2. The Informix-IDS service has been started. Select Start → All Progamme → IBM Informix Dynamic Server 11. Operation steps You can judge whether the Informix database can be used normally via the following steps. 1. Figure 2-11 The valid status of the configuration file If the configuration file is not valid. this indicates that the modified configuration file has been valid. Input onstat -l.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 3. 2-26 Version: B . If the system displays 40 total. please conduct the operations mentioned in Section 5. This chapter includes the following contents: Installation of the Server end Installation of the Client end Version: B 3-1 . which can perform the effective and unified management of multiple types of broadband access equipment developed by FiberHome.3 Installation of the ANM2000 The ANM2000 is an integrated broadband access management platform developed by FiberHome. This chapter introduces the installation methods of the ANM2000. 3-2 Version: B .e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 3.1 Installation of the Server End The server communicates with the managed system. In the installation of the server end. and saves them in the database. Operation steps 1. Double-click to make the Welcome dialog box appear. and you do not need to install the client end again. the client end can be installed automatically. Run the installation file.1. and then click Next. collects various data of the system.1 Running the ANM2000_Server Installation Package Prerequisites The Informix database and the Informix Client-SDK have been installed successfully. 3. Accept the software agreement. Version: B 3-3 . Set the personal information. please adopt the default value FiberHome. 3. Then click Next. Set your personal information.3 Installation of the ANM2000 2. Select Yes to accept the ANM2000 software agreement. for the Company Name item. here andb@ol_test is used). and IP address is the IP address bound with the database. and then click Next. 3-4 Version: B . Then click Next. Select the installation language. By default the database name is andb@ instance name (it should be the instance name of the installed Informix database. 5. Select English by default.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 4. Set the database information. 3 Installation of the ANM2000 In the dual-NIC mode. Then click Next. and then click Next. 6. Input the username and the password. Version: B 3-5 . Input the username and the password set in the installation of the Informix database (refer to Section 2. It is recommended to select Anserver. ANCollection. Manager. please refer to Section 5. and ANDumper by default.1). Select the services to be installed. 7.7 for determining the IP address bound with the database. select Yes. Then click Next. I want to restart my computer now to restart the computer. Set the installation path. a promotion will appear to ask the operator to restart the computer after the completion of the installation. In this case. 9. In the ANM2000 – InstallShield Wizard dialog box that appears.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 8. It is recommended to set the installation path as D:\AEMS. 3-6 Version: B . Input one of the following commands: C: \ Informix>d: D: \ >cd aems / server / andb D: \ AEMS \ Server \ andb \ createspaces –s –t|-m|-l Among them: -s: the singledisk. the harddisk space of 73 G is needed. Version: B 3-7 . -l: the large size mode. the harddisk space of 5 G is needed. 2. and the ANM2000 can manage 200 OLTs.3 Installation of the ANM2000 3. and the ANM2000 can manage 500 OLTs. -m: the medium size mode. the harddisk space of 15 G is needed. In the actual applications. and the ANM2000 can manage 100 OLTs. you need to stop the AEMS-CollectionServer. Note 1: The path inputted in the command is the default installation path. so you need to modify the path here based on the actual installation path.2 Creating the Tablespace Prerequisites Before creating the tablespace. in this mode. indicating that the generated space files are saved in one disk. AEMS-DBServer. Select Start → All Programme → IBM Informix Dynamic Server 11. the operator generally uses the medium size mode. Do not input all of them (–t|-m|-l) in a command. Note 2: Please select one from the –t|-m|-l in the command based on the network size. in this mode.1. and AEMS-Daemon services. -t: the small size mode. in this mode. AEMS-Manager. Operation steps 1.50 → ol_test. AEMS-DumpServer. 6.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) Figure 3-1 Creating the tablespace If the system displays the following information. Figure 3-2 The status of the successful creation of the tablespace If you fail to create the tablespace. please conduct the operations mentioned in Section 5. this indicates that the tablespace has been created successfully. 3-8 Version: B . Figure 3-4 The status of the successful initialization of the Table architecture Version: B 3-9 . this indicates that the tablespace architecture has been initialized successfully. input createandb.3 Initializing the Table Architecture After the tablespace is created successfully. Figure 3-3 Initializing the Table architecture If the system displays the information as shown in Figure 3-4.3 Installation of the ANM2000 3.1. Input the username and the password of the ANM2000. Use the same method to start the AEMS-Manager. 2.1.4 Starting the Service 1. By default the username and the password are both 1.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 3. Then click OK.1. AEMS-DumpServer. and AEMS-CollectionServer services. Right-click Computer. 3. Double-click to start the ANM2000. Select the AEMS-DBServer service. in this window. and the IP address of server to be logged in. 2. and select Manage to open the Server Manager window. 3-10 Version: B . select Configuration -> Services.5 Verifying the ANM2000’s Server End Installation 1. and click . and you can query the performances status of the managed system and handle the relevant alarms via the client end. Operation steps 1. this indicates that the installation is successful. so as not to input the IP address each time that you log in the server with the same IP address. and then click Next. Run the installation file. 3. Version: B 3-11 . The computer that carries the Client end can communicate with the ANM2000 server normally.3 Installation of the ANM2000 Note: You may click the button. If you can log in the ANM2000 successfully.2 Installation of the Client End The client end is a work station. input the IP address in the Server IP Management dialog box and click OK. Double-click to make the Welcome dialog box appear. the system displays the status of the managed system via the GUI.1 Running the ANM2000_Client Installation Package Prerequisites There is an ANM2000 server which has been installed successfully.2. In this mode. 3. Select Yes to accept the ANM2000 software agreement. Accept the software agreement. 3-12 Version: B .e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 2. for the Company Name item. Set the personal information.3 Installation of the ANM2000 3. please adopt the default value FiberHome. Version: B 3-13 . and then click Next. Select the installation language. Set your personal information. 4. Select English by default. Then click Next. Then click Finish. Set the installation path. 6. 3-14 Version: B . Then click Next. a promotion will appear to ask the operator to complete the installation. I want to restart my computer now to restart the computer. In this case. Complete the installation. It is recommended to set the installation path as D:\AEMS_Client. In the ANM2000 – InstallShield Wizard dialog box that appears.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 5. select Yes. Double-click to start the ANM2000. If you can log in the ANM2000 successfully. Input the username and the password of the ANM2000. 2.3 Installation of the ANM2000 3.2.2 Verifying the ANM2000’s Client End Installation 1. Then click OK. Version: B 3-15 . this indicates that the installation is successful. By default the username and the password are both 1. and the IP address of server to be logged in. . This chapter includes the following contents: The upgrade of the Server end The upgrade of the Client end Version: B 4-1 . the upgrade operation. This chapter describes the upgrade flow of the ANM2000 from the following three aspects: the preparation before the upgrade operation. and the confirmation after the upgrade operation. you need to upgrade the ANM2000.4 Upgrade of the ANM2000 When you want to obtain the newly-added functions of the new version or correct the faults of the current version. 07. the Informix database.2 Backup of the Original Configuration Files Operation purpose To avoid the data loss caused by the upgrade.02 version.1 Preparation before the Upgrade Operation The upgrade conditions: The computer to be the ANM2000’s Server end has been installed with the legal Windows XP professional SP2. 4.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 4. The installation package of the new version has been prepared. you need to upgrade the ANM2000’s Server end. so please confirm that your installation package is of the Build05. the Informix11. Windows2003.05. Version: B . and the detailed procedure of the upgrade is as follows: 4.07.5 database is used together with the ANM2000 with the Build05. or Windows2008 standard operating system. please back up the original configuration files before the upgrade operation. and relevant patches and tools. of the currently used and the upgrade ANM2000s. Operation steps 1. Confirm the version Nos. The operator has the basic operation knowledge of the legal Windows XP professional SP2 or Windows2008 standard operating system and the ANM2000.1 The Upgrade of the Server End When you want to obtain the newly-added functions of the new version or fix the bug of the current version.05. 4-2 Double-click to start the ANM2000.02 version.1. The flow of upgrading the Server end is illustrated in Figure 1-3.1. 4 Upgrade of the ANM2000 2. this indicates that the data are backed up successfully. Select System → Export Config to set the path of the backup file. 4. Operation step 1. Version: B 4-3 . so as to perform the upgrade again.1. When the following alert box appears.3 Backup of the Software Package To avoid the modification of the installation package caused by the upgrade failure. Save a copy of the ANM2000_Server file with the new version and the current version respectively. you can back up the installation directory of the current AEMS. please back up the software package of the new version and the current version. Note: If there is not the ANM2000_Server file with the current version. and then click OK. e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 4. you need to stop the AEMS-DumpServer. In this case. Method 2: Double-click to make the Confirm Uninstall dialog box appear. Prerequisites Before uninstalling the current ANM2000. Then the Maintenance Complete dialog box will appear to give a prompt that the original ANM2000 has been uninstalled. Select ANM2000.4 Uninstalling the Current ANM2000 After completing the backup before the upgrade.1. AEMS-DBServer. 2. click Finish. you can uninstall the current ANM2000 according to the following steps. and then click OK to uninstall the original ANM2000. 3. Operation steps Method 1: 1. and AEMS-Daemon services. AEMS-CollectionServer. and then click Delete. 4-4 Version: B . AEMS-Manager. Select Start → Control Panel to open the Control Panel window. Double-click Add or Delete Programme to open the Add or Delete Programme window. 4 Upgrade of the ANM2000 4.1.5 Installing the ANM2000 of the Upgrade Version The operations are the same as those of the installation of the Server end. For the detailed operations, refer to Section 3.1. Caution: After running the upgraded ANM2000_Server installation package, please conduct the creation of Tablespace and the initialization of the Table architecture. Version: B 4-5 e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 4.1.6 Importing the Configuration Data Operation purpose After the ANM2000 is upgraded, the database will be cleared. In this case, you need to import the backup configuration data to the network management system. Operation steps 1. Double-click to start the ANM2000. 2. Click 3. Select System → Import Config, and the system will give a prompt that the imported data may overwrite the current data; click Yes to confirm to continue the operations. 4. Select the path of the backup file, and then click OK. When the alert box as follows appears, this indicates the data have been imported successfully; in in the toolbar to make the system enter the edit mode. this case, click OK to restart the ANM2000 GUI. 4-6 Version: B 4 Upgrade of the ANM2000 4.1.7 Verifying the Upgraded Software Version Operation purpose After completing the upgrade, you need to check whether the upgraded software version is what you want. Operation steps Start the ANM2000, and select Help → About Anms in the main menu. In the About Anms alert box, click About Anms to view the version information. If the current version is the upgraded version, this indicates that the software version is correct. Version: B 4-7 4-8 Version: B . this indicates the configuration data are correct. Operation steps Start the ANM2000.1. and the Topology tab will display the configuration data before the upgrade. if so. View whether the systems and modules in each management domain can be displayed and operated on the GUI.8 Checking the Configuration Data Operation purpose After verifying the upgraded software version.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 4. you need to check whether the upgraded configuration data are identical to those before the upgrade. and then click OK to uninstall the original ANM2000.4 Upgrade of the ANM2000 4. Windows2008.2 The Upgrade of the Client End After completing the upgrade of the Server end. and the detailed procedure of the upgrade is as follows: 4. you need to upgrade the Client end too. of the new ANM2000 to be installed has been confirmed. Version: B 4-9 . The flow of upgrading the Client end is illustrated in Figure 1-4.1 Preparation before the Upgrade Operation The upgrade conditions: 4.2. Uninstalling the Current Client end Uninstall the current Client end according to the following steps. Double-click to make the Confirm Uninstall dialog box appear.2. Windows2003. Windows Vista or Windows7 operating system.2 The computer to be as the ANM2000’s Client end has been installed with the legal Windows XP. The version No. The installation package of the new version has been prepared. e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) Then the Maintenance Complete dialog box will appear to give a prompt that the original ANM2000 has been uninstalled. click Finish. In this case. 4-10 Version: B . 2.2. In the About Anms alert box.4 Upgrade of the ANM2000 4. Version: B 4-11 . click About Anms to view the version information. Operation steps Start the ANM2000. For the detailed operations. you need to check whether the upgraded software version is what you want.2. and select Help → About Anms in the main menu.4 Verifying the Upgraded Software Version Operation purpose After completing the upgrade. 4. this indicates that the software version is correct.3 Installing the Client End with the Upgrade Version The operations are the same as those of the installation of the Client end. refer to Section 3. If the current version is the upgraded version. . 5 FAQs This chapter introduces the solutions to common problems in the installation of the Informix11. This chapter includes the following contents: How to handle the invalid configuration file How to handle the long-period no response from the ANM2000 How to handle the inadequate disk space How to handle the Informix database not installed How to handle the connection failure of the ANM2000 How to handle the tablespace creation failure How to determine the IP address bound with the database How to handle the data exporting / importing failure Version: B 5-1 .5 and the ANM2000. but in this case. but the configuration file is still invalid. and then click Start. You can click to start the Informix IDS service normally. instance name file cannot be uploaded.1 How to Handle the Invalid Configuration File Question The etc\ONCONFIG. 5-2 Version: B . input –iy in the start parameter item. the ONCONFIG. instance name file during the initialization operation.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 5. The correct start method is described as follows: Double-click the Informix IDS service. How to handle this problem? Answer The probable reason of this is described as follows: The system only uploads the ONCONFIG. instance name file under the Informix installation directory has been modified. 5 FAQs Version: B 5-3 . and check various configuration items in this file according to Table 5-1. How to handle this problem? Answer The probable reason of the long-period no response from the ANM2000 is that the Informix service stops after it is started. input –iy in the start parameter item. The configuration parameters of the database can influence certain resources of the database. double-click the Informix IDS service.ol_test file under C: \informix\etc. certain resources may be inadequate. Use the notebook or the UE to open the onconfig. 5-4 Version: B . Table 5-1 Parameter values in the ONCONFIG file Parameter Item Recommended Value ROOTSIZE 1024000 PHYSFILE 50000 LOGFILES 40 LOGSIZE 10000 SHMVIRSIZE 32656 SHMADD 8192 EXTSHMADD 8192 After the configuration is checked and confirmed to be correct. and this can lead to the condition that the service cannot be started normally. the ANM2000 does not respond in a long period. if the configuration parameters of the database have errors. and then click Start.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 5.2 How to Handle the Long-Period No Response from the ANM2000 Question During the network management operation. Version: B 5-5 . the system gives a prompt that the disk space is inadequate. 15 G. you can select to create a relatively smaller database tablespace. and 73 G respectively.5 FAQs 5. or replace the harddisk. Table 5-2 The parameters for creating the tablespace Parameter Value Size Mode Needed Harddisk Space Management Capacity -t Small 5G 100 OLTs -m Medium 15 G 200 OLTs -l Large 73 G 500 OLTs When the disk space is inadequate. you can execute the following command to create the small-size / medium-size / large-size tablespace respectively. D:\AEMS\Server\andb\createspaces –s –t|-m|-l You should select to create the suitable tablespace on demand according to Table 5-2.3 How to Handle the Inadequate Disk Space Question When the operator tries to create the database tablespace. The created tablespace occupies the disk space of 5 G. How to handle this problem? Answer After the installation of the ANM2000. the system gives a prompt as shown in the following figure. How to handle this problem? Answer You can handle this problem as follows: 5-6 Version: B . How to handle this problem? Answer You need to install the Informix database before installing the ANM2000. For the detailed operation steps. please refer to Chapter 2 Installation of the Informix Database. 5.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 5.4 How to Handle the Informix Database Not Installed Question When the operator tries to install the ANM2000.5 How to Handle the Connection Failure of the ANM2000 Question When the operator tries to start the ANM2000. the system gives a prompt that the Informix database is not installed. and IP are correct. Version: B 5-7 . If the system displays On-Line. LOGIN_USER. please check whether the onconfig. Check whether the md.ol_test file under C:\informix\etc is configured correctly according to Table 5-1. 2.ini file under D:\AEMS\Server \ ini is configured correctly. Select Start → All Programme → IBM Informix Dynamic Server 11. If the database is not started normally. LOGIN_PASSWORD. and then input onstat – to check whether the database is started normally.5 FAQs 1.50 → ol_test. this indicates that the database is started normally. Check whether the parameter values of DATABASE_SERVER. AEMS-Manager services. AEMS-DumpServer. 5-8 2. 5. Select Start → All Programme → IBM Informix Dynamic Server 11.2. set the username to Informix and the password to Anms2k. 3. After confirming the correctness of the previous information.1. create the tablespace again. You can log in ol_test as an Informix user. Version: B . and then click OK. restart the AEMS-CollectionServer.6 AEMS-DBServer. the operator fails to create the tablespace. and then right-click ol_test to select Run Mode. 1. Confirm that the server IP address input via the Client end is correct. and then create the tablespace again. In the Run Identify dialog box.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 3. and How to Handle the Tablespace Creation Failure Question When trying to install the ANM2000. select Following User. Referring to Section 3.50 → ol_test. How to handle this problem? Answer This problem is probably be caused by the authorization limit. In the Adapters and Bindings tab. select Properties to open the Network and Sharing Center window. 5-9 . Select Manage Network Connections to open the Network Connections dialog box. Right-click Network. 3. how to determine the IP address bound with the database? Answer You can handle this problem as follows: Version: B 1. the NIC IP address with the highest priority in the Connections combo box is the NIC IP address bound with the database.7 How to Determine the IP Address Bound with the Database Question When the server is configured as the dual NIC mode. 2. Select Advanced → Advanced Settings to open the Advanced Settings dialog box.5 FAQs 5. 4. please contact the engineers of FiberHome for handling it. If the ANM2000 version has been modified. the data exporting / importing failure may occur. the format of the configuration data may also change. how to handle the data exporting / importing failure? Answer When exporting / importing the configuration data file. 5-10 Version: B . When one of the previous conditions occurs.e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows) 5. you need to convert the data format.8 How to Handle the Data Exporting / Importing Failure Question When needing to export / import the configuration data file (such as for the upgrade of the ANM2000). the ANM2000 needs to use a temporary tablespace. in this case. if the tablespace in the database is inadequate. Please take a moment to complete this survey. The personal information requested is used for no other purposes than to respond to your feedback. Documentation Name Code and Version Usage of the product documentation: 1. How do you like the language style of the documentation? Good Normal Poor (please specify) 3. When do you use the documentation? in starting up a project in installing the product in daily maintenance in Other (please specify) troubleshooting 3. Are any contents in the documentation inconsistent with the product? . Your answers will help us to improve the documentation and better suit your needs. How often do you use the documentation? Frequently Rarely Never Other (please specify) 2. Are you satisfied with the promptness with which we update the documentation? Satisfied Unsatisfied (your advice) 5.Product Documentation Customer Satisfaction Survey Thank you for reading and using the product documentation provided by FiberHome. Name Phone Number Email Address Company To help us better understand your needs. Which documentation form do you prefer? Print edition Electronic edition Other (please specify) Quality of the product documentation: 1. please focus your answers on a single documentation or a complete documentation set. Is the information organized and presented clearly? Very Somewhat Not at all (your advice) 2. What is the percentage of the operations on the product for which you can get instruction from the documentation? 100% 80% 50% 0% Other (please specify) 4. Your responses will be confidential and given serious consideration. What is your opinion on the Figures in the documentation? Beautiful Unbeautiful (your advice) Practical Unpractical (your advice) 10. What is your opinion on the layout of the documentation? Beautiful Unbeautiful (your advice) 11. how would you compare our documentation to them? Product documentations from other companies: Satisfied (please specify) Unsatisfied (please specify) 12. If you have any questions or concerns about this survey please email at edit@fiberhome. Thinking of the documentations you have ever read offered by other companies. .4.cn.com. Is the information complete in the documentation? Yes No (please specify) 5. Which parts of the documentation are you satisfied with? 8. Can you successfully implement a task following the operation steps given in the documentation? Yes (please give an example) No (please specify the reason) 7. Please fax or send the completed survey to us at the contact information included in the documentation. Which parts of the documentation are you unsatisfied with? Why? 9. Additional comments about our documentation or suggestions on how we can improve: Thank you for your assistance. Are the product working principles and the relevant technologies covered in the documentation sufficient for you to get known and use the product? Yes No (please specify) 6. . . 5 Dongxin Rd. Address: No...FiberHome Telecommunication Technologies Co. China Zip code: 430073 Tel: +86-27-87691549 Fax: +86-27-87691755 Website: http://www.fiberhomegroup. Wuhan. Hongshan Dist. Ltd.com .