ACRIS - PFA Teflon® Lined ISORIA - Elastomer Lined MAMMOUTH - Large Diameter Elastomer LinedButterfly Valves for High Corrosion, Ultra High Purity and General Industrial Applications. ® Teflon is a registered trademark of E.I.DuPont Company. spherically molded liner. ® Teflon and Viton are registered trademarks of E. sealing against the matching spherically machined disc hub when compressed by the resilient elastomer backup liner. • Flange Sealing Provided by compression of the liner between the valve body and the flanges. The PFATeflon® liner as well as the PFA-Teflon® shaft overmolding extends into the valve body itself. An elastomer o-ring. and allows the resilient elastomer back-up liner to compress the spherically molded PFA-Teflon® liner into the spherically machined shaft-disc with enough force to create a tight seal. This seal is constantly energized by a coil spring.DuPont Company.I. allows proper flange sealing with warped flange faces or in vacuum applications. and self compensates for temperature changes and wear. 2 . This is in contrast to PTFE liners which are usually thick sinterings resulting in a stiff liner unable to give tight shut-off over a long period of time. Tight compression is maintained at the hub area and around the shaft by the resilient back-up liner combined with the flexible PFA-Teflon® liner.ACRIS Sealing Principles • Primary and Secondary Shaft Sealing The primary seal is formed by the flexible. This has enabled the ACRIS to be used for pump and vessel isolation as well as other difficult services. forming an independent secondary seal. The wide elastomer backup liner in the ACRIS rests in a machined body groove which is essential in providing tight shut-off for end of line service at full pressure. which provides force against the junction of the PFATeflon® liner and PFA-Teflon® overmolded shaft. fitted underneath the PFA-Teflon® liner. • Safety Sealing A third seal is provided by a graphitefilled PTFE safety seal. • Upstream/Downstream Sealing The dense PFA-Teflon® body liner is flexible. 0002 psia) to 150 psi Temperature: – 20°F to 320°F Downstream Dismantling: All Lug body valves are rated for full working pressure. the ACRIS has a long. The superior pressure/temperature operating parameters are conservatively stated for reliable. Flange Adaptability: ASME B16. ASME B16. full-term operation of the valve. and offer the purity required for ultra high purity applications. The ACRIS can be used for end of line service and provide tight shut-off at the full rated pressure of the valve.0002 PSIA). ACRIS valves withstand the effects of all known corrosive fluids. ball and knife gates in nontraditional butterfly valve applications. ACRIS PFA-Teflon® lined butterfly valves can be used for pressures up to 150 psi and for industrial vacuum (to 0. PFA-TEFLON® liner (grade 350 or 450 HP) Resilient back-up liner (silicone or VITON®) VITON® o-ring Graphite-filled PTFE safety packing PTFE-filled stainless steel bearing Spring retention collar (AISI 304 stainless steel) Expansion plug (18-8 stainless steel) Psi 150 75 0 -20 Pressure-temperature limits 302 320 F o 3 .ACRIS Retaining ring (AISI 302 strain hardened) VITON® o-rings external seals Thrust collar AISI 304 stainless steel PTFE-filled stainless steel bearing Compression spring (AISI 1085 steel) Graphite-filled PTFE safety packing APPLICATIONS VITON® o-ring PFA-TEFLON® liner (grade 350 or 450 HP) Resilient back-up liner (silicone or VITON®) ACRIS butterfly valves often replace other types of valves such as plug. Other flange drillings are available on request.1 Class 125.5 Class 150. indefinite life in most applications. ACRIS PERFORMANCE CHARACTERISTICS One-piece 17-4 stainless steel shaft/disc overmolded with PFA-TEFLON® (grade 350 or 450 HP) Sizes: 1” to 24” Wafer body 1” to 24” Lug body Pressure: Full industrial vacuum (0. with the downstream piping removed. The ACRIS is also suitable on steam service (up to 280°F) alternating with the flowing media. Operated within these parameters. absolute tight sealing at all critical points (upstream/ downstream. Complete compatibility with a wide range of AMRI manual. filled sleeve bearings). pneumatic. • Low pressure drop (smooth profile liner and disc). 20. • “Locked-In” liner design provides for tight shut-off at full differential pressure with the downstream flange removed.).01 PSIA) to 375 psi* -40°F to 392°F (Depending on materials used) ASME B16. 4 .316 Stainless or Alloy 20 • Pulp Stock: Lining . • Minimal required torque (PTFE. • Minimal overall dimensions and weight. • Blowout proof shafts. Included in this series is the MAMMOUTH for large diameter (up to 120”) and high pressure (up to 375 psi) applications.316 Stainless • Weak Acids: Lining .EPDM or Hypalon Disc . This connection method also allows for easy disassembly of the valve. depending on the selection of materials: • Water: Lining . • No required maintenance (no adjustable packing gland.47 Class 150 series A PN 10. 316 Stainless or Aluminum bronze • Brine: Lining . Sanitary construction (no fluid or particulate material traps).EPDM or Nitrile Disc . hydraulic and electric actuators.ISORIA • • • Bi-directional flow and tight shut- off characteristics. Many years of superior service have proven the advantages of the ISORIA butterfly valve: • Reliable. The ISORIA valve uses a spherically machined disc and a one-piece body that is totally isolated from the flowing media by means of the inner lining.Industrial vacuum (.Ductile iron.1 Class 125 ASME B16..Industrial vacuum (. 16.EPDM or Hypalon Disc .01 PSIA) to 375 psi* MAMMOUTH . PERFORMANCE CHARACTERISTICS Sizes: Pressure: Temperature: Flange Adaptability: ISORIA MAMMOUTH PTFE Sleeve bearing Shaft retainer 1½” to 40” Wafer 42” to 120” Flanged 26” to 40” Flanged 1½” to 24” Lug body 14” to 24” Semi-lug body ISORIA .5 Class 150 ASME B16. 25 AWWA C207 Class B. • Strong internal shaft-disc connection (splined shafts <24in.316 Stainless or Alloy 20 Upper atmosphere seal One Piece Body PTFE Sleeve bearing Splined shaft-disc connection Replaceable molded liner completely encapsulating the valve body Spherically machined disc Lower shaft Lower cover CONSTRUCTION FEATURES The ISORIA elastomer-lined butterfly valve is part of a series of valves designed for the multitude of moderately corrosive applications throughout industry. • Economical use of body materials (valve body is totally encapsulated by the inner lining).EPDM or Hypalon Disc . perma- nently lubricated). parallel keys>24in. D & E Upper Shaft PTFE Sleeve bearing Shaft retainer 8” valve shown * Upper pressure limit varies on different models. shaft and flanges). TYPICAL APPLICATIONS The ISORIA butterfly valve is suitable for a great variety of applications. A strong shaft-disc connection is provided by an exclusive splined shaft/parallel key arrangement for precise positioning and reliable operation. 24”) T5 .40”) (1½” .40”) ISORIA 20 (300 psig) Please consult AMRI ISORIA 25 (375 psig) 66” to 120” 42” to 96” 44” to 84” 44” to 78” 44” to 72” MAMMOUTH 6 T5 . Grade 350 Teflon® assembled.24”) (Standard for 40” T4 .Semi-lug T2.40”) (1½” .24”) (14” . (2” to 12”) tested & packaged for ULTRA PURE service ASTM A193 Grade B7 body bolts (in lieu of standard A193 Grade B8) *NOTE: Valve face-to-face is per ISO 5752 and API-609 dimensions except for 14” and 18” ACRIS.40”. For Example: 6” ACRIS IL-31KF/S9 = IL 3 1k F /S9 ISO Lug ISORIA 16 T1-3t6k6XA = Ductile iron body 17-4 Stainless over molded with PFA Grade 350 Teflon® PFA Grade 350 Teflon® liner Viton® back-up liner 16 T1 3t 6k 6 XA StandardNo extra code S9 S9C SC1 SB7 16 bar (240 psig) Wafer Cast iron body 420 Stainless shaft 316 Stainless disc EPDM liner 5 .40”) (1½”.Flat face flanged (6” . T4 & T5) (Optional 1½” . cleaned.Flat faced 3g = Ductile iron 6k = 420 Stainless (90 psig) flanged MAMMOUTH 10 (42” . 6e = 17-4 Stainless T2 – Semi-lug T2. T4 & T5) (Optional 1½”.24”) (T1 26” .120”) (150 psig) MAMMOUTH 16 (240 psig) MAMMOUTH 20 (300 psig) MAMMOUTH 25 (375 psig) DISC LINER OPTIONS CODE 2 = Aluminum bronze XA = EPDM 3a = Halar ECTFE XV = High temperature coated ductile iron EPDM 3g = Ductile iron K=Nitrile 3p = Hard rubber CB = Carboxylated coated ductile iron nitrile 3x = EPDM CC = White carboxylated coated ductile iron nitrile 5a = Ferralium Y = Hypalon® 6 = 316 Stainless VA = Acid Viton® 6i = Polished 316 VC = High temperature ® stainless Viton 6u = Alloy 20 7c = Hastelloy C 2 = Aluminum bronze XA = EPDM 3g = Ductile iron XV = High temperature 6 = 316 Stainless EPDM 6i = Polished K = Nitrile 316 stainless Y = Hypalon® 2 = Aluminum bronze 3g = Ductile iron 3p = Hard rubber coated ductile iron 6 = 316 Stainless XC = EPDM K = Nitrile 1” ACRIS IW–ISO 3 = Ductile iron wafer (One-piece shaft/disc) F = PFA Grade Silicone back-up liner to Wafer 350 Teflon® 24” (1” to 24”) 3 = Ductile iron lug 1k = 17-4 Stainless over molded with PFA H = PFA Grade IL–ISO Grade 350 Teflon® 450 Teflon® Viton® back-up liner Lug (1” to 24”) 1h = 17-4 Stainless Viton® back-up liner. 6e = 17-4 Stainless T2 .Butterfly Valves HOW TO ORDER VALVES SIZE TYPE VALVE BODY STYLE BODY MATERIAL SHAFT 1½” ISORIA 10 T1 – Wafer 3t = Cast iron 6k = 420 Stainless to (150 psig) (1½”. over molded with PFA ASTM A193 ® Grade 450 Teflon Grade B7 bolts.24”) T5 .40”) 1½” ISORIA 16 T1 – Wafer 3t = Cast iron 6k = 420 Stainless to (240 psig) (1½”.40”) (1½”.Flat face flanged (6” .24”) (Standard for 40” T4 . cleaned.24”) (T1 26” .Lug 3g = Ductile iron 1½” .Lug 3g = Ductile iron 1½” .24”) (14” . (1” to 14”) tested & packaged for chlorine gas service 1s = Carbon steel over molded with PFA Silicone back-up liner.40”. 6 .50 25.969 1.00 27.02 1.49 16.88 4.12 24 600 19.921 5.69 1.511 5.630 .74 1.312 0.56 5.08 24 600 19.08 5.48 14.85 1.12 2.417 1.921 5.630 .199 16.000 0.708 0.86 13.99 E SHAFT D C I SO TOP FLANGE MOUNTING ∅F ∅G (Bolt Circle) (Hole Size) WEIGHT IN MM IN IN IN 1 25 3.19 4.12 4.748 .35 1.630 .93 1.708 0.756 2.511 6.22 1.866 * 1 to 1½ inch valves are wafer with alignment holes.000 0.68 19.181 1.80 2.630 .181 1.85 2.02 1.199 16.748 .25 2.69 3 80 4.82 3.12 5.287 2.43 3.968 1.02 1.756 4.85 7.094 .19 **14 350 13. Pattern F05 F05 F05 F05 F07 F07 F07 F10 F12 F12 F14 F14 F14 F16 F16 4 4 5 5 10 12 25 42 70 110 172 231 330 440 565 1.02 1.35 2 50 4.24 1.02 1.12 16 400 14.92 6.375 0.181 1.48 17.45 1.92 IN IN 1.511 5.312 0.312 0.756 2.35 1.984 1.61 1.25 8 200 8.20 ISO LBS.81 5.437 0.75 10 250 10.756 4.48 14.69 1.496 0.432 11.630 .20 ISO LBS.432 11.25 8 200 8.969 2.511 6.12 5.85 1.83 2.016 4.148 15.85 7.562 0.562 0.62 10.312 0.630 .62 4.312 0.562 0.375 0.11 4.630 .88 4.03 8.05 1.11 16 400 14.25 2.35 23.708 0.382 9.99 10. ØG E B ACRIS (I SERIES) 1” TO 24” Lug Body SIZE A B C D IN 3.02 1.511 5.921 4.271 5.984 1.02 1.756 2.094 .496 6.13 **18 450 16.575 1.23 6.011 22.630 .05 4 100 5.000 0.148 15.22 1.969 1.06 3.02 1.03 8.921 4.417 1.38 3.12 6 150 6.000 0.98 20.03 20.43 **14 350 13.866 0.25 2.49 16.88 1.866 0.22 1.08 6. SQUARE ØF A 4 HOLES.417 1.38 3.74 32.969 1.312 0.ACRIS SQUARE ØF A 4 HOLES. Pattern F05 F05 F05 F05 F07 F07 F07 F10 F12 F12 F14 F14 F14 F16 F16 4 4 6 6 12 17 29 50 78 116 195 229 344 400 649 1.02 1.35 1¼ 30 3.417 1.93 1.69 *1½ 40 3.496 0.81 20 500 17.13 4.24 3 80 4.708 0.74 1.41 10.972 19.016 4.969 2.40 28. ** 14 and 18 inch ACRIS valves do not conform to ISO 5752 face-to-face dimensions.968 1.61 1.562 0.708 0.286 3.252 13.630 .45 1.69 *1¼ 30 3.969 1.287 2.38 3.708 0.02 1.75 2.08 20 500 17.375 0.630 .575 1.835 1. ØG E B D C ACRIS (I SERIES) 1” TO 24” Wafer Body SIZE A B C D E SHAFT ISO TOP FLANGE MOUNTING ∅F ∅G (Bolt Circle) (Hole Size) WEIGHT IN MM IN IN *1 25 3.375 0.181 1.83 4 100 5.972 19.22 1.11 12.02 1.969 1.835 1.62 24.88 2 50 4.93 12 300 11.48 32.439 7.22 15.630 .88 6.51 2.431 18.312 0.80 6 150 6.24 15.93 2.969 1.312 0.35 1.02 1.48 17.011 22.68 19.74 1.51 10 250 10.02 1.61 1.82 12 300 11.382 9.06 Disc Chord Square Height Length 0.25 2.74 4.511 5.35 1½ 40 3.74 1.98 23.496 6.630 .97 5.69 1.67 Disc Chord Square Height Length 0.73 8.74 3.866 ** 14 and 18 inch ACRIS valves do not conform to ISO 5752 face-to-face dimensions.630 .12 **18 450 16.54 13.630 .41 10.271 5.439 7.62 4.02 1.375 0.756 2.88 6.375 0.38 3.85 2.252 13.55 7.437 0.286 3.54 13.61 1. 55 6.14 17.74 4.67 3.48 2.708 0.492 11.756 4.75 9.417 1.181 1.69 12.74 10.551 0.20 2.433 0.492 11.87 Disc Chord F ∅G Square Height Length 0.17 4.25 10.04 2.41 7.45 8.165 2.99 14.496 0.708 0.305 22.36 2.756 4.01 4.33 7. ØI ØG 14" TO 24" A SQUARE ØH E B 4 HOLES.551 0.648 3.969 2.417 1.09 10.551 0.945 .13 5.68 16.74 23.921 5.748 0.8 5.708 0.82 12.07 3.432 5.494 7.708 0.433 0.708 0.69 1.96 16.945 1.275 0.67 3.25 18.165 2.771 2.14 10.74 10.102 - - - - - - - - - - - - - 0.921 5.04 2.945 .116 2. TOP PLATE 1 1/2" TO 12" ØH F 4 HOLES.551 0.016 4.69 1.958 1.551 0.275 0.866 4.984 0. IN MM IN IN IN IN 1½ 2 3 4 6 8 10 12 14 16 18 20 24 40 50 80 100 150 200 250 300 350 400 450 500 600 4.66 5.354 0.486 16.165 2.771 2.165 2.10 13.708 0.32 Disc Chord F ∅G Square Height Length 0.984 1.708 0.101 0.4 2.63 8.48 5.354 0.59 6.31 22.51 11.32 19.26 32.921 4.378 1.958 1.41 7.551 0.748 0.00 6.07 4.63 8.945 .968 .28 1.8 12 24 52 85 101 136 222 268 394 564 7 .433 0.5 8.708 0. ØI ISORIA 1½” TO 24” Wafer Body SIZE A B C D E SHAFT ISO TOP FLANGE MOUNTING ∅H (Bolt Circle) ∅I (Hole Size) WEIGHT LBS.26 3.433 0.267 12.91 14.016 4.81 25.511 5.417 1.51 3.551 0.866 - - - - - 0.354 0.24 1.28 2.575 1.708 0.417 1.275 0.102 - - - - - - - - - - - - - 0.559 ISO Pattern F05 F05 F05 F05 F07 F07 F10 F12 F12 F14 F14 F14 F16 1.401 18.511 5.29 1.29 1. IN MM IN IN IN IN 1½ 2 3 4 6 8 10 12 14 16 18 20 24 40 50 80 100 150 200 250 300 350 400 450 500 600 4.551 0.00 6.378 1. ØI ISORIA 1½” TO 24” Lug Body SIZE A B C D E SHAFT D C ISO TOP FLANGE MOUNTING ∅H (Bolt Circle) ∅I (Hole Size) WEIGHT LBS.11 20.866 - - - - - 0.32 19.378 1.401 18.95 14.551 0.486 16.06 3.433 0.74 4.945 .575 1.18 20.06 4.511 6.433 0.03 28.33 7.417 1.275 0.ISORIA TOP PLATE 1 1/2" TO 12" ØH F A 4 HOLES.511 5.14 17.433 0.275 0.748 0.432 5.708 0.969 1.969 1.984 1.551 0.83 27.968 .945 1.165 2.48 2.551 0.378 1.417 1.20 2.13 17.511 6.267 12.59 6. ØI ØG 14" TO 24" B E SQUARE ØH D C 4 HOLES.511 5.5 15 23 36 66 110 158 211 286 418 Consult AMRI for 26" to 40" valve dimensions.51 9.62 10.551 0.96 16.55 6.03 11.116 2.408 9.354 0.275 0.03 11.51 18.969 2.47 8.01 4.494 7.748 0.13 4.921 4.73 12.984 1.11 12.969 1.945 .03 11.433 0.07 4.60 5.945 .275 0.20 15.31 5.496 0.969 1.13 4.551 0.408 9.305 22.09 17.5 8.18 14.181 1.984 1.101 0.648 3.165 2.4 5.693 14.984 0.559 ISO Pattern F05 F05 F05 F05 F07 F07 F10 F12 F12 F14 F14 F14 F16 1.969 1.693 14.275 0.81 2.07 3.31 5.51 3.48 5.18 14.756 2.28 2.756 2.866 2.551 0.10 13.81 2.969 1.36 2.66 6.13 5. 14 12.18 60° .48 17.486 16.511 5.496 0.ISORIA SQUARE ØF A 4 HOLES.559 ISO LBS.165 2.866 Flow Coefficient Factors at 10o Increments for ACRIS and ISORIA Angle Cv 10° 0 20° .05 40° .511 6.401 18.03 29.07 4.13 33.305 22.95 20 500 17.708 0.74 28.708 0.32 14.06 23.69 18 450 16.984 1.101 0.18 10.96 11.03 1 6 400 14.90 90° 1.70 Disc Chord Square Height Length 12.708 0.14 25.30 70° . Pattern F12 F14 F14 F14 F16 135 180 247 326 496 4.13 24 600 19.771 2.165 2.551 0.50 80° .00 6.921 5.417 1.28 IN IN 3.693 14.01 4.165 2.10 50° .511 5.968 1.02 30° .0 8 . ØG E B D C ISORIA 14” TO 24” Semi-Lug Body SIZE A B C D E SHAFT ISO TOP FLANGE MOUNTING ∅F ∅G (Bolt Circle) (Hole Size) WEIGHT IN MM IN IN 14 350 13.48 5.417 1.417 1. concentrated bases. pellets Acids. warm gases All chemical products EPDM XA High Temperature EPDM XV Nitrile Rubber K Carboxylated Nitrile CB Hypalon® Y Acid Viton® VA High Temperature VC Viton® PFA . High temperature process applications (Same as XA) Hydrocarbons. warm) amines. AMRI has created its own molding manufacturing division. FLOW COEFFICIENTS Cvo = gallons/minute with DP = 1 psi SIZE ACRIS MODEL ISORIA 10 ISORIA 16 1 1¼ 1½ 2 2½ 3 4 5 6 8 10 12 14 16 18 20 24 ≥ 26 50 50 100 209 376 580 916 1276 2320 5800 9396 15892 21344 26912 34104 41760 60500 — — 62 154 280 475 760 1044 2090 4120 8453 10465 12880 17020 22655 28750 41860 — — 62 154 280 475 760 1044 2090 4120 8453 10465 9269 12075 15295 20010 28750 Cross-sectional view of typical installation options WELD-NECK FLANGE SLIP-ON FLANGE Please consult AMRI 9 . ketones. industrial. • To produce all elastomers and PFA-Teflon® parts in-house in order to ensure components appropriate for butterfly valve working conditions. esters. This division was created with three specific goals: • To define and create elastomer formulations best suited for specific applications. • To exercise complete quality control over the elastomers and PFA-Teflon® parts from verification of the raw materials to testing of the finished product.Teflon® F ®Teflon.I. As a result. In order to maintain high quality standards of the elastomers and PFA-Teflon® parts. brine.Butterfly Valves ELASTOMERS & PFA-TEFLON® AMRI butterfly valves offer a long and reliable operational lifetime due primarily to: • The superior mechanical design details and manufacturing quality. bases. AMRI can recommend the best suited valve for each application. weak acids. Viton and Hypalon are registered trademarks of E. aromatic Hydrocarbons. • The high quality of the valve’s inner lining. abrasive chemicals. PARTIAL LIST OF AVAILABLE VALVE LINERS LINER MATERIAL TYPICAL APPLICATIONS Water (soft. sea. DuPont Company. caustic soda Concentrated acids Solvents at high temperature. sand. and low aromatic content oils Abrasive applications: cement. nitrogen derivatives. roller bearings. locks in any position. epoxy coated.Variable torque advantage output for reduced input force. ductile iron housing. locks in 10 positions. 6. visual indication. 10 . ISO valve drilling patterns. Hard anodized aluminum housing. actuator base has multiple ISO valve drilling patterns. stainless input shaft. DOUBLE ACTING ACTUATORS ACTAIR SERIES RACK & PINION: 1. NAMUR accessory mounting. cataphoresis coated end caps. MANUAL GEAR MG .MANUAL LEVERS: CR . MR . 3. ductile iron cylinder.Ductile iron epoxy coated.Ductile iron epoxy coated. visual indication. PTFE sleeve bearings. epoxy coated. 200. stainless trim. epoxy coated. NAMUR accessory mounting. 25. SM . iron bearings. 12. Cast iron housing. steel and stainless internals.Worm gear. DOUBLE SCOTCH-YOKE: 100. VARIABLE TORQUE OUTPUT: 400. cast iron housing. 800. epoxy coated. cast iron housing.5. direct mount limit switch capability. visual indication. bronze and steel internals. M31 .Worm gear. 50. NEMA 4. 4x or 7.5. fail open or fail closed ACCESSORIES POSITIONERS 3-15 psig or 4-20 mA inputs.SPRING RETURN ACTUATORS DYNACTAIR SERIES RACK & PINION: 1. 800. VARIABLE TORQUE OUTPUT: 200. LOCK-OUT/TAG-OUT Available for all levers. Hard anodized aluminum housing. NEMA 4. AC/DC current. NEMA 4X housing. 100. visual indication. steel cylinder. 1 X ½” NPT or 2 X 3/4” NPT conduit entries. & III. 7. NAMUR accessory mounting. 4X. Ductile iron housing. NAMUR mount. low. 12. fully adjustable cams. simple mechanical zero and span adjustments. steel and stainless internals. SOLENOID VALVES 3 way and 4 way. epoxy coated. high and max flow spool valves with low air consumption. LIMIT SWITCHES Mechanical or proximity. 25. II. Groups A-G. 6. 11 . AC or DC current. actuator base has multiple ISO valve drilling patterns. closed. or both positions depending on customer requirements. internal terminal strip. 3. standard or NAMUR mount type manual override. manual gears and valve actuators. NAMUR accessory mounting. fail open or fail closed. cataphoresis coated end caps. 400. Allows locking of valves in open. and anodized Aluminum. stainless steel. DOUBLE SCOTCH-YOKE: 50. brass. visual indication. Class I. and 9. Divisions 1 & 2. NAMUR mount. ISO valve drilling patterns. Peñuelas. 19 COL.This catalog is not contractual and may be amended without notice.V.com http://www. S. CP 73120 Phone: +52 (442) 220-6363 Fax: +52 (442) 220. Texas 77055 Phone: (713) 682-0000 Fax: (713) 682-0080 KSB. SAN PEDRITO PEÑUELAS QUERETARO/QUERETARO STATE. VA 23231 Phone: (804) 222-1818 Fax: (804) 226-6961 GIW Industries. Las Esteras Sur #2851 Comuna de Quilicura. Upper middle: Manually operated 8” ACRIS replacing plug valves for pump isolation in EDC and VCM service.A. 5000 Wrightsboro Road Grovetown. Santiago Phone: (011) 562-677-8300 Fax: (011) 562-677-8301 FACTORIES SALES OFFICES MEXICO KSB de Mexico. No. Texas 77055 Phone: 713-682-0000 Fax: 713-682-0080 Email: info@amrivalves. mounted to a 10” ACRIS isolating a CLO2 tank in a pulp mill.com C-1002 / 10•01•2007 Revision 3.B1606DVE Carapachay Buenos Aires. AV. 2045 Silber Road Houston. S. USA ARGENTINA BRAZIL CHILE AMRI.amrivalves. 4415 Sarellen Road Richmond.Várzea Paulista . Inc. Georgia 30813-9750 Phone: (706) 863-1011 Fax: (706) 860-5897 KSB Compania Sudamericana de Bombas S. Av.6389 Butterfly Valves Actuators and Systems AMRI. S. Argentina Phone: (011) 54-11-4766-3021 Fax: (011) 54-11-4766-5499 KSB Bombas Hidráulicas. 400 13220-000 .Upper left: DYNACTAIR spring return actuator with lock-out/tag-out. Inc. Inc. .A. Upper right: Manually operated 4” ACRIS for UV light isolation in high purity water. Ader 3625 .A.A. Inc. 2045 Silber Road Houston. de C.SP Phone: (011) 5511-4596-8500 Fax: (011) 5511-4596-8747 KSB Chile. Rua José Rabelo Portella.