93577744-Manual-de-Usuario-Procash-NDC-v-1-3

ProCash/NDC ProConsult/NDCUser Guide V1.3/00 V1.1/00 Edition October 2004 Copyright and Trademarks Copyright © Wincor Nixdorf GmbH & Co. KG 2004. All rights, including rights of translation by printing, copying or similar methods, even of parts, are reserved. All rights, including rights created by patent grants or registration of a utility model or design, are reserved. Delivery subject to availability; right of technical modifications reserved. All names of hardware and software products mentioned in this manual are trade names and/or trademarks of their respective manufacturers. All hardware and software names used are trademarks of their respective manufacturers. Reliant® is a registered trademark of Pyramid Technology Corporation. SINIX is the UNIX System derivative of Wincor Nixdorf GmbH & Co. KG. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. Base: OSF/Motif™, Copyright © Open Software Foundation, Inc. X Window System™, Copyright © Massachusetts Institute of Technology. OSF/Motif is a trademark of Open Software Foundation, Inc. X Window System is a registered trademark of Massachusetts Institute of Technology. MS-DOS® and Windows® are registered trademarks of Microsoft Corporation in the United States and other countries. ® Introduction Software Structure System Setup Modes of operation Configuration Data Security Features Messages Printers Additional useful Information Abbreviations Figures Tables Related publications Contents Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 What’s new . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wincor Nixdorf Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose of the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supported hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi Vendor capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Products of ProCash/NDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Products of ProConsult/NDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dynamic Link Libraries (DLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parameter / Data Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Types of Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compatible Customization Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extended Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global Screen Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Error Mapping Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Font Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15 15 16 17 18 19 20 21 23 23 26 26 27 28 29 30 31 31 System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Directory Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-up mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exiting power-up mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Out-of-service mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . In-service mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Offline mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service and Operating(SOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 42 42 42 43 44 44 45 October 2004 Contents Automatic return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . In-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Start Rear Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customize Rear Balancing functions . . . . . . . . . . . . . . . . . . . . . . . . . . . Dispense Below Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 47 47 47 48 49 Miscellaneous Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 ADRS operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Steps processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Card Read State (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 PIN Entry State (B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Customer Selectable PIN State (b) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Extension to state (b) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Envelope Dispense (C) State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Pre-Set Operation Code Buffer State (D) . . . . . . . . . . . . . . . . . . . . . . . . 72 – Clear mask (entry 3) example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 – A, B, C, D preset masks (entries 4-7) example . . . . . . . . . . . . . . . . . 75 Extension to State (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Four FDK Selection Function State (E) . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Amount Entry State (F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Amount Check State (G) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Information Entry State (H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Transaction Request State (I) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Extension to state (I) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Close State (J) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 FIT Switch State (K) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Card Write State (L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Enhanced PIN Entry State (M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Enhanced Amount Entry State (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Extension to State (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Language Code Switch State (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Extension to State (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Card Read - PIN Entry Initiation State (T) . . . . . . . . . . . . . . . . . . . . . . . 116 Extension to State (T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Language Select From Card State (V) . . . . . . . . . . . . . . . . . . . . . . . . . 120 October 2004 Contents FDK Switch State (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FDK Information Entry State (X) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extension to State (X) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Eight FDK Selection State (Y) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extension to State (Y) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi Language Extension to State (Y) . . . . . . . . . . . . . . . . . . . . . . . . . Audio Control State (i) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Fitness State (‘h’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extension to State (‘h’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Smart FIT Check State (‘k’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Skip State step . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screen Control Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displaying Graphics as Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Full Screen graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Display resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displaying MacroMedia Flash executables . . . . . . . . . . . . . . . . . . . . . Displaying Video files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voice Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Auto Voice Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Audible Echo on Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reserved Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logical Unit Number (LUNO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local download feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure local download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN and PIN Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Personal Identification Number (PIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable length PIN Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Offset Number (DES verification) . . . . . . . . . . . . . . . . . . . . . . . . . PIN Verification Processes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 126 129 132 135 136 138 142 145 148 152 153 153 158 158 158 159 159 160 160 161 162 165 166 166 166 167 173 173 175 175 176 177 177 178 178 179 180 October 2004 Contents Local PIN Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network PIN Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – ANSI PIN/PAN Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Diebold PIN Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ID Card and FIT Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ID Card Data Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIT (Financial Institution Table) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIT Library Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi Card, Multi Institution Capability . . . . . . . . . . . . . . . . . . . . . . . . . . Alternate Transaction Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIT Data Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Institution Index (PIDDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Institution Identification (PFIID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIT Switch Index (PSTDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum PIN Entry Digits (PMXPN) . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Check Length (PCKLN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Pad Character (PINPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAN Index (PANDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAN Length (PANLN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAN Pad Character (PANPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Retry Count Index (PRCNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Offset Number Index (POFDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decimalization Table (PDCTB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Encrypted PIN Key (PEKEY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Track Locator (PINDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Language Code Index (PLNDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Message Authentication (MAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAC flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Terminal Number (Machine Number) . . . . . . . . . . . . . . . . . . . MAC data field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time variant number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical Message Authentication Procedure . . . . . . . . . . . . . . . . . . . . . MACing for State and FIT Table Load commands . . . . . . . . . . . . . . . . . Triple DES operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EMV capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Key Loading (RKL) capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 181 182 183 184 185 186 186 187 188 188 188 190 191 191 191 192 194 195 195 196 196 197 197 197 198 198 199 199 200 201 201 201 202 203 203 203 204 October 2004 Contents Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages from Terminal to Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transaction Request message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solicited Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unsolicited Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network to Terminal messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transaction Reply command (message ID ‘4’) . . . . . . . . . . . . . . . . . . . Terminal Command message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . State Tables Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screen Data Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration Parameters Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enhanced Configuration Parameters Load . . . . . . . . . . . . . . . . . . . . . Interactive Transaction Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIT Data Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Encryption Key Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extended Encryption Key Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dispenser Currency Mapping Table Load . . . . . . . . . . . . . . . . . . . . . . Configuration ID Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date And Time Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Message Authentication Field Selection Load . . . . . . . . . . . . . . . . . . . Specific Command Reject Conditions . . . . . . . . . . . . . . . . . . . . . . . . . Terminal operations in Transaction Replies . . . . . . . . . . . . . . . . . . . . . . . . Print Immediate (‘4’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Next State and Print (‘5’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Night Safe Deposit and Print (‘6’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deposit and Print (‘1’ or ‘7’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dispense, Deliver and Print (‘2’ or ‘8’) . . . . . . . . . . . . . . . . . . . . . . . . . Display and Print (‘3’ or ‘9’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Eject Card, Dispense and Print (‘A’) (Card before Cash) . . . . . . . . . . . Eject Card, Dispense and Print (‘F’) (Parallel CBC) . . . . . . . . . . . . . . . Parallel Eject/Dispense and Print (Fast Cash) (‘B’ or ‘C’) . . . . . . . . . . . Print Data and Stay in Present State (‘P’) . . . . . . . . . . . . . . . . . . . . . . . Print Statement and Set Next State (‘Q’) . . . . . . . . . . . . . . . . . . . . . . . Electronic Journal Upload (EJU) commands . . . . . . . . . . . . . . . . . . . . . . . Send Options And Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acknowledge And Continue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acknowledge And Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NDC Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solicited Status (terminal state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . October 2004 205 205 209 218 223 225 226 235 239 242 245 249 254 258 261 264 267 269 272 275 280 287 288 288 289 289 291 291 292 293 294 294 295 295 296 299 301 303 303 . ./unsol. . . . . . . . . . . . . Electronic Journal Upload (EJU) Message . . . . . . . . . . – Dispenser (sol. Electronic journal storage . . . . Additional Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . Types of journal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer Control Characters . . . . . . ./unsol. – Power Up (unsolicited) (DID ‘B’) . . . . . . . . . . . . . . . . .) (DID ‘V’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Sensor Status (unsolicited) (DID ‘P’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Supplies Data . . . . . . Solicited Status (device fault) . . . . . 304 313 316 320 321 324 325 327 328 330 331 335 337 338 342 346 348 349 351 353 356 357 361 361 363 364 367 367 368 369 369 370 370 371 371 376 378 October 2004 . . . . . . . . . Electronic journal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing with the Windows GDI Interface . . . . . . .) (DID ‘E’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screen Design Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ./unsol. . . . . . . . . . . . . . . . . . . . – EDM . . . . . . . . – Statement Printer (sol. . . . . . . – Local Configuration Option Digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Fitness Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Module (unsolicited) (DID ‘L’) .Contents – Send Configuration Information . . . . . . – Software ID and Release Number . – Send date/time information . . . . . . . . . . . . . . . . . . . . . . . . . . . . ./unsol. . . . . . . . . . Printer Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASCII to EBCDIC Code Conversion Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Card Reader (sol. . . . . . . . . . . . . – Vandal Guard (unsolicited) (DID ‘J’) . . . . . . . . – Hardware Configuration Data . . . . . . . . . . . . . . – Tamper and Sensor Status Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Supervisor Key Messages (unsolicited) (DID ‘R’) . . . . . . . . . – Journal Printer (unsolicited) (DID ‘H’) .) (DID ‘F’) . . . – Door Access (unsolicited) (DID ‘N’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Send Supply Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unsolicited Device Status . . . . . . . . . . . . . . . . . . – Send Error Log Information . . . . . . . . . . . – Envelope Dispenser (unsolicited) (DID ‘\’ . . . . . . . . . . . . . . . . . Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .) (DID ‘D’) . . . . . . . . . . . . . . – Receipt Printer (unsolicited) (DID ‘G’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NDC Standard Character Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – Depository (sol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer Monitor ND9G (Class: 0040) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer (Class: 0032) . . . . . . . . . Motorized Door (Class: 000E) . . . . . . . . . Printer ND75/75S/94 (Class: 0034) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer TP07 (Class: 0045) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer Extensions (Class: 003F) . . . . . . . . . . . . Cash Dispenser (Class: 643A) . . . . . . . . . . . . . . WOSA Cash Dispenser (Class: 00B9) . . . . . . . . . . . . . . . . . . . . Cash Dispenser V1 (old series) (Class: 0007) . . . . . Printer USB/TP06 (Class: AA48) . . . . . . . . . . . . . . . . . . . Printer Monitor TH21 (Class: 0041) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer TP07 GDI (Class: 0044) . . . . . . . . . . . . . . . . . . . . . Transaction (Class: 6434) . . . . . . . . . . . . . . . . . . Card Reader (Class: 0008/AA08) . . . Cash Dispenser NG (Classes: 0018/AA18/001D) . . . . . . . . . . . . . . . . . 379 379 379 383 392 405 406 407 411 414 415 416 417 418 418 419 420 422 423 423 424 424 426 427 428 430 431 433 433 434 435 435 436 437 437 438 438 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer System Framework (Class: 0042) . . . . . . . . . . Printer USB/TP07 (Class: AA45) . . . . . Printer ND79 (Class: 0035) . . . . . . . . . . . . . . . . . . . . . . . 443 October 2004 . . . . . . . . . . . . . . . . . . . . . . . . Encryption Decryption Module (Class: 000F) . . . . . . . . . . Encryption Decryption Software (Class: 0011) . Printer TP06 (Class: 0048) . . . . . . . . . . . . . .Contents M-Status & M-Data Reference Tables . Printer ND71/74/98/9A/9C/9E/TH30 (Class: 0033) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer ND99 (Class: 0038) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cash Cheque Deposit Module (Classes: 001A/XX1A) . . . . . . . . . . . . . . . . Printer TH21 (Class: 003E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vandal Guard (Class: 0015) . . . . . . . . . . . . . . . . . . . . . Electronic Journal (Class: 0091) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cheque transaction (Class: 645A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer ND97/TH97/TP01/NP01/TP05/NP05 (Class: 0039) . . . . . . . . . . . WOSA Error Classes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deposit Module (Class: 0017/AA17) . . . . . . . . . . . . . . . . CSC-W32 Error Classes . . . . . . . . . . . . . . Application Error Classes (LYNX errors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EMV transaction (Class: 6459) . . . . . . . . . . . . . . . . CashIn transaction (Class: 6446) . . . . . . . . Security Module (Class: 643C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Contents Figures . . . . . . 453 October 2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Since November 2003 until October 2004: q q q q q q q q q New section ”Electronic Journal Upload (EJU) commands” on page 295 New section ”Electronic Journal Upload (EJU) Message” on page 364 New section ”Remote Key Loading (RKL) capability” on page 204 New section ”EMV capability” on page 203 New section ”Displaying MacroMedia Flash executables” on page 159 New section ”Smart FIT Check State (‘k’)” on page 148 Changed section ”Hardware Fitness State (‘h’)” on page 142 Changed section “Amount Check State (G)” on page 84 New section “Dispenser Currency Mapping Table Load” on page 267 Since May 2002 until November 2003: q q q q q q q q q q q New section ”Miscellaneous Operations” on page 51 Changed section ”Related publications” on page 453 New section ”M-Status & M-Data Reference Tables” on page 379 New section ”Triple DES operation” on page 203 Extended section ”Solicited Status messages” on page 218 Extended section ”Send Configuration Information” on page 304 Changed section ”Software Products of ProConsult/NDC” on page 21 Changed section ”Software Products of ProCash/NDC” on page 20 New section ”Printing with the Windows GDI Interface” on page 370 Changed section ”Dynamic Link Libraries (DLL)” on page 23 Changed section ”Directory Structure” on page 34 October 2004 13 .What’s new This section lists a summery of documentation changes and enhancements of the ProCash/NDC User Guide. What’s new Since October 2001 until May 2002: q q q q q q q q q New section “Enhanced Amount Entry State (R)” on page 107 New section “Audio Control State (i)” on page 138 New section “Voice Control” on page 160 New section “Dispense Below Zero” on page 49 Enhanced section “Unsolicited Device Status” on page 335 Enhanced section “Printer Models” on page 367 Changed section ”Related publications” on page 453 Enhanced section ”Directory Structure” on page 34 Enhanced section “Solicited Status (terminal state)” on page 303 14 October 2004 . October 2004 15 . Wincor Nixdorf provides ProCash/NDC and ProConsult/NDC with function messages of NCR terminals which are described in later sections. or Diebold hardware) is another big advantage of this software architecture. Any function restrictions against NCR can be recognized if it is not documented in this manual. The existing MS-DOS based NDC-Emulation from Wincor Nixdorf is running in NCR network environments all around the world.Introduction Preface Introduction Preface In the past NCR and Diebold/Interbold have dominated the international market of automated teller machines (ATM). The application design allows customers to create easily new Frameworks of customer specific functions using ProTopas/KIT. ProTopas is a flexible development platform for self-service device applications in open system environments. New technologies and of course windows oriented platforms provided from Microsoft has forced Wincor Nixdorf to develope the NDC-Emulation running with Windows. Both vendors have defined very similar protocols for the network integration of their systems. Development with ProTopas means using existing Frameworks. Wincor Nixdorf Solution ProCash/NDC and ProConsult/NDC have been developed using the C++ object oriented ProTopas architecture. The ability to integrate ProCash/NDC in multi vendor projects (ProCash/NDC running on NCR. using WOSA services. The product ProCash/NDC and since October 2002 ProConsult/NDC from Wincor Nixdorf has been developed with all known advantages provided by Windows like Multithreading Processes. Olivetti. modifying and creating new Frameworks for the specific self-service application. open system environment through the ProTopas architecture from Wincor Nixdorf. commands and messages will be described here in detail. as far as it is NDC specific and not covered by other documentation (e. In this case please refer to the protocol descriptions of the network (in case of project specific extensions) or to recent releases of the Programmers Reference Manuals of NCR. CSC-W32. Any feature exceeding the described ones may not be supported.Purpose of the Document Introduction Purpose of the Document This document will provide the software analyst with the necessary information on the functions which are supported by product ProCash/NDC and ProConsult/NDC. either by file download or as an online-documentation.g. Since the list of supported features keeps growing please always use the latest release of this documentation. FIT. Protopas or ProDevice documents). NDC specific features like States. Screens. A detailed description of all the application specific parameters will be found in the ProCash/NDC ProConsult/NDC Installation manual along with information for installation and upgrading the products. Furthermore all the information needed for the operation of the ATM. We will make updated versions available as soon as practical. 16 October 2004 . thus defining the available functions. The functionality depends on the host Software (BASE24. Those are typically (but not exclusively): q q q q q q q q q q q q q q q Withdrawal Fast cash Deposit Balance inquiry Transfer Payment PIN change Rear Balancing Multi language Statement print MACing Triple DES security EMV support Cheque deposit (ProCash/NDC only) (ProCash/NDC only) (ProCash/NDC only) E-Journal Upload (EJU) October 2004 17 .Introduction Function Overview Function Overview ProCash/NDC and ProConsult/NDC written for Wincor Nixdorf terminals contain base functions from the original NCR Direct Connect (NDC) software provided by NCR.). FIT’s. Screens and Parameters controls the terminal. TP/2. etc. The download of original NCR Customization Tables such as States. ON/2. ND71. 18 October 2004 . NP07 q Statement: ND97. CDM-NG (6 cassettes) Needle printers: q Journal: ND98D. V5 (international) Deposit modules: q Papalakko. Certo Dispenser modules: q CDM-V1. ND9A. ID24 (DIP reader). NP06 q Receipt: ND9E. TH23 Card readers: q ID14 (Sankyo Seiki).. ND98. TH21. TP07 q Journal: TH30. ID15 (Wincor Nixdorf). ND97 Thermal printers: q Receipt: ND9C. ND71. ND99. 3100xe Info Terminals: q ProPrint 200 q ProPrint 2000 q ProConsult. CSC1500 q Cash Recycling System (CRS)..Supported hardware Introduction Supported hardware Currently following systems and hardware components are supported: ATM’s: q CSC4xx Rear/Frontload q CSC400 Frontload q ProCash-Compact q ProCash 2000 q CSC21xx. V2X. TH22. ND94. ICM300 (manual smart card reader) Encryption modules: q EDM module (restricted security). CMD-V4. Wincor Nixdorf q Cheque Deposit Module (CCDM) continued on next page . EPP’s V4. CDM-NG. ND9G. TP01. V4+. ID18 (OMRON). TP06 q Statement: TH97/G. or high end) q Touch screen support q Power Supply box q Sound card q USB support Multi Vendor capability Multi Vendor capability Since release 1. but they have to be installed with a special prepared installation set: q q q Fujitsu cash systems Olivetti cash systems Delarue cash systems October 2004 19 . which can be installed via standard installation procedure via ProInstall: q q NCR cash systems Diebold cash systems.3/00 ProCash/NDC supports hardware platforms from other vendors as well. Follwing hardware platforms of other vendors are supported.Introduction Miscellaneous: q Operator Panel (Low. (except OPTEVA) Following vendors are running with ProCash/NDC. Pure Windows XP needs 1.7/01 1.0 3. 6 2.0/31 3.0/53 4.0) WOSA/XFS-SSP (3. The Windows NT system needs minimum 128 MB RAM at runtime and one hard disk with the minimum capacity of 500 MB to store the whole software.1/13 3.0 optional optional For detailed information about function and configuration of each product refer to ProCash/NDC ProConsult/NDC Installation manual NOTE 1: ProCash/NDC is running on on PC based systems.2/02 3.0) WOSA/XFS-SSP/MV PARAC-NT ProView ProCash/NDC ProCash/NDC-SOP current Release Systems see Note2 4.8 GB hard disk space.1/72 4.00 Srv.Software Products of ProCash/NDC Introduction Software Products of ProCash/NDC In the following table is listed the basic software products that are required to setup a whole ProCash/NDC application: Table 1: Basic Software of ProCash/NDC Name Operating system Windows XP Professional Windows NT CSC-W32 ProCash/Topas ProSop WOSA/XFS-SSP (2.3/00 all all all all all all all all all all Communication software SNA-Workstation Eicon software components 4. For Windows XP 256 MB RAM and hard disk space of 4 GB is required. NOTE 2: Windows XP is released on Embedded PC’s only.1/71 3.1/00 3. 20 October 2004 . For Windows XP 256 MB RAM and hard disk space of 4 GB is required. October 2004 21 .1/72 4.1/71 3. The Windows NT system needs minimum 128 MB RAM at runtime and one hard disk with the minimum capacity of 500 MB to store the whole software.0 3.0/31 3.Introduction Software Products of ProConsult/NDC Software Products of ProConsult/NDC In the following table is listed the basic software products that are required to setup a whole ProConsult/NDC application: Table 2: Basic Software of ProConsult/NDC Name Operating systems Windows XP Professional Windows NT CSC-W32 ProCash/Topas ProSop WOSA/XFS-SSP (2.0 optional optional For detailed information about function and configuration of each product refer to ProCash/NDC ProConsult/NDC Installation manual NOTE 1: ProConsult/NDC is running on on PC based systems.1/00 3.1/13 3.0) WOSA/XFS-SSP/MV PARAC-NT ProView ProConsult/NDC ProConsult/NDC-SOP current Release Systems see Note2 4.00 Srv.7/01 1. NOTE 2: Windows XP is released on Embedded PC’s only.8 GB hard disk space.0) WOSA/XFS-SSP (3.1/00 all all all all all all all all all all Communication software SNA-Workstation Eicon software components 4.0/53 4. Pure Windows XP needs 1. 6 2.2/02 3. Software Products of ProConsult/NDC Introduction 22 October 2004 . It maps the physical cassettes to logical positions which have to match with the positions configured at the host side. These modules control the functions of the application.dll) (not ProConsult/NDC) The Cash Dispenser Framework controls the dispensing requests from the consumer. which have to be installed via ProInstall on the harddisk of the ATM.dll) The Transaction Framework maps the downloaded NDC states to the belonging step function defined in the LYNXPAR section of the registry. October 2004 23 . etc. It asks the Device Status Framework for the current status of the device to fill the severity and supply status fields of solicited and unsolicited messages to be sent to the host. The actual status will be passed to the Message Control Framework whenever it asks for the device status. q Message Control Framework (dcmsgcfw..Software Structure Dynamic Link Libraries (DLL) The following described Dynamic Link libraries are the part of ProCash/NDC or ProConsult/NDC. The following software modules build the application part NDC on the ATM: q Transaction Framework (dcsttfw. q Cash Dispenser Framework (dccdmfw.dll) The Device Status Framework collects the status of the devices from the different device frameworks. q Device Status Framework (dcdevsta. It handles the cassette counters and syncronizes them with WOSA.dll) The ProSop User Exit Framework contains NCR service functions like “Display supply status. “Rear balancing”. “Clear card capture counter”.dll) The Message Control Framework handles the NDC messages sent from the host to the terminal and builds up the messages which have to be sent from the terminal to the host. It also offers the supplies of the devices. q SOP User Exit Framework for ProSop (dcsuefw. q SOP Dialog Framework (dcSopDia. First it reads the base settings from the registry and set it as default (sets lpi and cpi size.dll) The Converter Framework handles the Customisation Image (CI) downloaded from the host.dll) The NDC Printer Framework analyzes the printer data from the host and converts it to printable printer buffers. etc. It starts the Protocol Framework. q NDC Dialog Framework (ndcdiafw. q SOP Service Framework (dcServic.Dynamic Link Libraries (DLL) q Software Structure NDC Printer Framework (ndcprtfw. q Application Framework (dcapplfw. The formatted print buffer will be passed to the base printer framework of ProTopas. Step Table Framework and handles the synchronisation with the different Frameworks. q Security Overlay Framework (dcsecure. Communication Framework.dll) The Protocol Framework send to or receives messages from the Communication Framework. q Converter Framework (dcconvfw. PIN inputs and controls the screen flow.dll) The Security Framework performes local PIN verification with the corresponded FIT data. It stores the host configuration (States. Configuration parameters and Configuration ID) in the LYNXCI path of the Registry. Screens. FIT table . activates the printer font.dll) The SOP service framework contains Dialog and synchronisation functions of ProCash/NDC-SOP ProConsult/NDC-SOP. reads the char convertion table. Performs calls to security functions of Protopas basic framework.dll) The NDC Dialog Framework handles the consumer FDK.) after that it fills the printer data with the specific macros depending on which NDC escape sequences are in the printer data from the host. 24 October 2004 .dll) The SOP dialog framework controls the dialog screens on the facia screen or on the operator panel of ProCash/NDC-SOP or ProConsult/NDC-SOP. Timers. q Protocol Framework (dcprotfw.dll) The Application Framework has the control above the other Frameworks. Please refer to Wincor Nixdorf / Diebold D91x Message Format Extension for EMV for detailed descriptions. This Overlay framework has to be configured in between the ProTopas printer framework and the NDC Printer Framework in the Repository Manager. Please refer to Wincor Nixdorf / Diebold D91x Message Format Extension for EMV for detailed descriptions.User Guide for detailed descriptions about GDI printing with ProCash/NDC and ProConsult/NDC.dll) The GDI Printer Overlay Framework converts PrintRaw data to GDI print data. q EMV Transaction Overlay Framework (dcEmvTa.dll) The EMV Converter Overlay Framework is needed to handle EMV download data. q EMV Converter Overlay Framework (dcEmvCv. October 2004 25 . Refer to GDI Printer Overlay Framework .g. which are passed to a Windows printer (e.dll) The EMV Transaction Overlay Framework is needed to handle transactions with EMV data. Please refer to Wincor Nixdorf / Diebold D91x Message Format Extension for EMV for detailed descriptions. ND9G). q EMV Message Control Overlay Framework (dcEmvMc.Software Structure q Dynamic Link Libraries (DLL) GDI Printer Overlay Framework (dcPrtGdi.dll) The EMV Message Control Overlay Framework is needed to append messages with EMV data. Existing parameters can be edited in text files (*. Our ProCash/NDC and ProConsult/NDC emulation fully supports this Customization Download. not on the ATM. card read . The Registry update with the changed values will be done via PARAC-NT after the next “RUN” process and with CCRCCONV.Parameter / Data Files Software Structure Parameter / Data Files Types of Parameters Every terminal needs many different parameters to operate as expected. needs several parameters to cover the differences to the original systems and for enhanced services.ina type).g. The Wincor Nixdorf solution.. NCR supports the central customization by files which will be distributed to all connected ATM’s.. The parameters will be stored into the Windows registry. The most complex set of parameters is called "Customization" and contains the dialogs and the sequence of functional steps (e. Changes to those parameters may be overwritten any time by a new download.ppf or *.EXE. Furthermore each ATM will have a number of extended parameters which are specific to its type or to the particular machine. 26 October 2004 . Thus permanent changes must be made to the customization files on the Host.PIN Entry Function selection .) which the system will perform. Details will be given in the ProCash/NDC ProConsult/NDC Installation manual. being an emulation. Software Structure Parameter / Data Files Compatible Customization Data All customization data are stored in the Windows registry location: HKEY_LOCAL_MACHINE\ SOFTWARE\ Wincor Nixdorf\ ProTopas\ CurrentVersion\ LYNXCI q Screen Data (LYNXCI\SCREEN\XXX [1]) [1] ’XXX’ represents the downloaded screen number are the predefined display screens provided by the host. Client card data are compared to data in this file to determine whether the card holder can receive services..\LYNXCI\R00” and “. Those screens are stored in sub section “.. q EMV Parameters (LYNXCI\EMV) This section contain specific EMV parameters. October 2004 27 . q Timers (LYNXCI\TIMER) contain downloaded timer values valid for all ATM’s in the network. q Customization Parameters (LYNXCI\PARAMETER) contain some terminal specific settings and specific definitions of the message protocol. q State Table (LYNXCI\STATE) is used to define and control the logic flow of the for client transactions. LYNXCI\SCREEN\R01) As part of the screens download the host can send receipt header data (R00) and predefined receipt data (R01) (data that are mixed together with the host printer data of the transaction reply). q Receipt Templates (LYNXCI\SCREEN\R00.\LYNXCI\R01”. q Financial Institution Table (LYNXCI\FIT) consists of an entry for every institution or group of institutions offering services on the ATM. (This section is missing in the non cash product ProConsult/NDC.Parameter / Data Files Software Structure Extended Configuration Data All non downloaded configuration data are stored in the following location of the Windows registry: HKEY_LOCAL_MACHINE\ SOFTWARE\ Wincor Nixdorf\ ProTopas\ CurrentVersion\ LYNXPAR q Application Parameters (LYNXPAR\APPLICATION ) This section contain parameters which are not assigned to a specific hardware device. dispenser status. q Deposit Parameters (LYNXPAR\DEPOSIT) This section contain parameters related to the deposit module. q Cash Dispenser Parameters ( LYNXPAR\CASH_DISPENSER) This section contain parameters related to the cash dispenser like cassettes type configuration. These are global settings of NDC and can be parameters for the protocol or timers etc. q GDI Printer Parameters ( LYNXPAR\GDI_RINTER) This section contain parameters for printers using GDI.. receipt and document printers.) q Card Reader Parameters (LYNXPAR\CARD_READER ) This section contain parameters related to the card reader like track configuration and transport handling of the ID card. 28 October 2004 . q Operator Screen Parameters ( LYNXPAR\OPERATOR_SCREENS) This section contain the operator screen template parameters that are used to display or print the supply counters within the user exit menu “Individual Functions” of ProSop. dispense algorithm. q Printer Parameters (LYNXPAR\PRINTER) This section contain parameters related to the journal. Software Structure q Parameter / Data Files Function ID mapping (LYNXPAR\FUNC_ID_MAP) This section contain the assignment to the ProCash/NDC or ProConsult/NDC step functions and function ID’s that are send in transaction replies.PCX). October 2004 29 .AVI.MPG) etc.BMP) and Videos (*. Those parameters are stored in the following location of the Windows registry: HKEY_LOCAL_MACHINE\ SOFTWARE\ Wincor Nixdorf\ ProTopas\ CurrentVersion\ LYNXCI\SCREEN LYNXCI\SCREEN\XXX Details will be given in the ProCash/NDC ProConsult/NDC Installation manual. Furthermore for each screen can be configured special display settings or idle rotations which are independend from the host download. Bitmaps (*.. *. q State mapping (LYNXPAR\STATE_MAP ) This section contain the assignment to the ProCash/NDC or ProConsult/NDC step functions and state ID’s that are send in the states table download from host. Global Screen Configuration The global non downloaded screen configuration contains default display settings and path for graphic files (*. Each class contains sub sections of error codes which contain the CSC-W32 error and the error mapping definitions for the message protocol. The “CLASS” section is devided in the CSC-W32 device classes inclusive the ProCash/NDC classes.Parameter / Data Files Software Structure Error Mapping Configuration All device errors and mapping parameters are devided in error classes. They are stored in the following location of the Windows registry: HKEY_LOCAL_MACHINE\ SOFTWARE\ Wincor Nixdorf\ ProTopas\ CurrentVersion\ CCERRMAP\CLASS Details will be given in the ProCash/NDC ProConsult/NDC Installation manual 30 October 2004 . FON NDC-SA2.FON NDC-DA1. The fonts can be created and modified via utility “FONTEDIT.FON Designation Single Size Alpha 1 Single Size Alpha 2 Double Size Alpha 1 Double Size Alpha 2 Standard Graphic 1 Standard Graphic 2 Standard Graphic 3 Single Size Arabic Double Size Arabic 640x480 (W * H) [1] 20x30 20x30 40x30 40x30 20x30 20x30 20x30 20x21 40x42 800x600 (W * H) [1] 25x37 25x37 50x37 50x37 25x37 25x37 25x37 25x26 50x52 1024x768 (W * H) [1] 32x48 32x48 64x48 64x48 32x48 32x48 32x48 32x33 64x64 [1] - Depending on the display resolution you have to select the belonging font with the correct width and height (W * H).FON NDC-DA2.FON NDC-SARA.EXE”.FON NDC-GA1.FON NDC-GA2.FON NDC-GA3. During the installation the default base set of ProCash/NDC or ProConsult/NDC fonts will be installed and activated automatically like standard Windows fonts.FON NDC-DARA.FON) for displaying text and graphic characters for downloaded NDC screens. October 2004 31 . During the installation the standard fonts are automatically installed with the display resolution currently set in the control panel of Windows.Software Structure Font Files Font Files ProCash/NDC uses the Windows font format (*. The following section contains a short list of NDC Standard Fonts that are installed during the installation of ProCash/NDC or ProConsult/NDC: Standard Fonts Table 3: Standard fonts table Font name 1 2 > ? 3 4 5 9 B File name NDC-SA1. Font Files Software Structure 32 October 2004 . EXE’ located in the root of the ProInstall CD. October 2004 33 . The installation process will be started via program ’SETUP. All details about product installation will be provided in the ProCash/NDC ProConsult/NDC Installation manual. You can set also specific parameters via a parameter configuration dialog.System Setup Software Installation The whole software will be installed via the ProInstall Product CD. Customizing and Update diskettes. During the installation you will guided via menu dialogs through the installation processes. dll dcServic.dll 3DesEppF. A lot of directories and a large number of Dynamic Link Libraries (DLL’s) makes it difficult to assign configuration files and DLL’s to the right software sub product. The following table gives short overview about the modules and their directories: Table 4: Software structure File Structure \CSCW32 \WOSASSP \PROSOP \PROTOPAS fwstrt.dll dcSueFW.Directory Structure System Setup Directory Structure ProCash/NDC or ProConsult/NDC is only one part of a bundle of software packages running on an Windows based ATM.log \PROTOPAS\BIN dcApplFW. ProConsult/NDC-SOP Service Framework ProCash/NDC-SOP.dll dcDevSta.bat ccprot. ProConsult/NDC-SOP Dialog Framework NDC Dialog Framework NDC Printer Framework 34 October 2004 .dll dcSttFW.dll dcSecure. Protopas based DLL’s and ProCash/NDC or ProConsult/NDC specific DLL’s are stored together in directory C:\PROTOPAS\BIN.dll ndcPrtFW.dll dcConvFW.dll dcMsgcFW.bat fwkill.dll dcCdmFW.dll dcSopDia.dll ndcDiaFW.dll Description modules of CSC-W32 operating system modules of ProDevice (WOSA) modules of ProSop Starts ProCash/NDC or ProConsult/NDC Stops ProCash/NDC or ProConsult/NDC Log file of Host and ATM messages Application Framework Transaction Framework Message Control Framework Converter Framework Cash Dispenser Framework Sop User Exit Framework Security Overlay Framework Triple DES EPP Overlay Framework Device Status Framework ProCash/NDC-SOP. prtmakro.ina prosop.dll dcEmvMc.exe Update job for *.INA files to *.OK after the call).INA files to update existing and store new parameters in the Registry Batch file which is called once immediately after installation to store additional parameters in the registry (will be renamed from *.bat October 2004 35 .exe \PROTOPAS\CONF Kconf.RCK files Converts *.bat) Description GDI Printer Overlay Framework EMV Transaction Overlay Framework EMV Converter Overlay Framework EMV Message Control Overlay Framework TcpIP converter for 2 bytes binary headers (header length excluded) TcpIP converter for 2 bytes binary headers (header length included) TcpIP converter for 4 bytes ASCII headers (header length excluded) TcpIP converter for 4 bytes ASCII headers (header length included) TcpIP converter for 3 bytes ASCII headers (header length excluded) TcpIP converter for STX and ETX message length calculation Host Simulator Framework Updates the Windows registry with contents of *.ok (conv-all.dll dcEmvTa.dll dcTcp2hi.dll dcEmvCv.dll dcTcp2h.System Setup Directory Structure File Structure dcPrtGdi. Parameter source file of printer parameters used by Kconf.dll dcTcp3a.bat conv-all.dll ccrcconv.exe Batch job to set SOP User Exit and Trace menu items for ProSop (Single DES).dll dcTcp4a.exe Kconf. Batch job to store additional parameters for the journal and receipt printer to enable ’INIT’ sequences via makros.dll dcTcpSTX.bat prtmakro.RCK format Describes functionality of Kconf.BAT to *.txt conv.dll dcTcp4ai.dll dcSimCom. ASCII (default is ASCII .bat Description Parameter source file of SOP User Exit and Trace (Single DES) used by Kconf. Windows XP general optimations Windows XP Explorer optimations autostrt.fil (asc.XP tune_xp.ina lynxsop.INF files and contents of *.ina ccvtable.bat’ call.ina logon.Directory Structure System Setup File Structure prosop.bat tune_xp.ina sop3des.bat logon. Parameter source file of GDI printer parameters used by Kconf.REG files.bat’ process is running.exe Batch job to set parameters in the Registry to activate automatic logon. Contains configuration files needed to optimize Windows XP Batch routine that installs the *.bat’ process is running. Parameter source file of SOP User Exit and Trace (Triple DES) used by Kconf. Parameter source file of Rear Balancing step table parameters which is used during ’conv-all. Line convertion tables: EBCDIC .ina ccerrmap.bat gdi_prt.ina gdi_prt. Parameter source file of all application and CSC-W32 error codes and mapping definitions which is used during ’conv-all.bat sop3des.ASCII and ASCII . Parameter source file for automatic logon parameters Batch job to set one parameter which activates an automatic call of ’C:\STARTUP.ina autostrt. Parameter source file for the automatic ’startup.reg explorer.exe Batch job to set SOP User Exit and Trace menu items for ProSop (Triple DES).exe Batch job to set GDI printer parameters. ebc) cfgmanag.BAT’ after restart.ASCII) Link of the Configuration Manager for the start bar of Windows.inf 36 October 2004 .lnk \PROTOPAS\CONF\ TUNING. AVI.bin Description Windows XP settings for enhanced performance Windows XP reduced boot delay time Windows XP autorun settings Windows XP switch off welcome screen CMOS file .MPEG \PROTOPAS\FONTS \PROTOPAS\FONTS\640x480 \PROTOPAS\FONTS\800x600 \PROTOPAS\FONTS\1024x768 \PROTOPAS\FONTS\ GDI_PRT \PROTOPAS\TOOLS HostSim. Video animation file which can be configured instead of a ’normal’ graphic in the registry section “. TP07).MPG.inf bootload.inf autorun. *. ND9G. Graphic and Bitmap files which are controlled via screen escape sequences or as a local definition for Background pictures or to replace downloaded NDC text screens. \PROTOPAS\BITMAPS \PROTOPAS\BITMAPS\640x480 \PROTOPAS\BITMAPS\800x600 \PROTOPAS\BITMAPS\1024x768 *.ICN.BMP.exe October 2004 37 .\LYNXCI\SCREEN”.JPG dctmpoos. Last Transaction Status information) Resolution depended sub directories where the default graphics are stored during the installation. Bitmap which is displayed during the system shutdown initiated by the restart handler in a fatal error condition.bmp dcoos. Contains Windows fonts that are used if GDI printing is enabled (e.stores transaction oriented counters and device statuses (e.g.g. *.PCX. Bitmap which is permanently displayed if the maximum system reboots has been initiated by the restart handler. *. Resolution depended sub directories where the default fonts are stored during the installation.bmp *.inf nowelc..System Setup Directory Structure File Structure perform. *. *.inf \PROTOPAS\WORK cccmos. Dialog oriented host simulator simulates host to terminal messages. Converts ASCII printer fonts to *. Easy access to analyzing tools and configuration data via pull down menus.exe asc2logo.exe Description Dialog window where you can enter specific screens to display during runtime.exe to write tracks on ID cards.DOF format.Directory Structure System Setup File Structure MfcDlg.exe nd99-asc.exe asc2fon.cmd fontedit.LOG’ Initiates a system shutdown or relogon Utility to write track 1. Extracts binary *. Extracts 2 or 16 color PCX graphics to ASCII matrix text file. Configuration Manager.exe nd9e-dof. Modifies and view Windows font contents Converts ASCII font files to Windows fonts Extracts Windows fonts to ASCII text files Sends control sequences (in *. Message analyzer of log file ’CCPROT. Converts an ASCII logo file to DOF format for ND9E printer. Font and Logo loader for ND99 Extracts ND99 logo files to ASCII matrix file Converts ASCII logo files to binary logo files for ND99.exe pcx2asc.exe asc-nd99.exe ldnd99. Displays variables (e. Extracts DOF files to ASCII printer font files Converts ASCII printer font files to *.exe dof2asc.SWF format for ND99 printer.exe cfgmanag.exe prt-dof.exe nd99logo.g.exe MfcVar.2 or/and 3 data on ID cards via ID Card Unit.DOF format) to the receipt or journal printer.exe reboot. 38 October 2004 .exe fon2asc.exe protlog.exe write-id. Batch file which can be modified for calling write-id.exe asc2dof.SWF font files of ND99 to ASCII matrix font files.exe write-id. Opcodes) during the transaction flow. exe dof-rj03. Test utility that can print a text file with ASCII printer data and macros via printer interface of CSC-W32.exe icn2asc.exe confchck. Installes and registers Windows font files. Manager cfgmanag. ProConsult/NDC-SOP User Manager. Sets hardware depended menu for Status Overview in ProSop and deconfigures paper journal of no journal printer is installed. Test utility that prints raw data via ProTopas API function PrintRaw() from file C:\PROTOPAS\RAWDATA.TXT.exe dcsopmgr.exe rj03-dof.System Setup Directory Structure File Structure cfgmanag.exe compregf. but can be ordered from WCN support). Extracts ICN icon files to ASCII matrix files. or prints the contents of registry parameter MSGxxx via function Print(xxx). Converts ASCII printer fonts to *.exe asc2pcc.exe cpyntfnt. Compares an extracted registry text file with the contents of the Windows registry. Deletes keys from EPP and gives detailed information about the EPP hardware. Help text file for the Configuration Manager.hlp ina2def.exe October 2004 39 . Converts hex *.exe printraw. Configuration Utility.exe sethwppf. Converts ASCII files to PCC/PCX files. ProCash/NDC-SOP. (Will not be installed. Converts ASCII files to ICN files.exe prt-raw.DOF format for NP06/TP06 and NP07/TP07. It is called during installation and by the Config. Converts INA files to PARAC definition RC source files.exe asc2icn. (used during installation).exe initepp.DOF files of NP06/TP06 and NP07/TP07 font definitions to ASCII files.mnu Description Menu definition file for the Configuration Manager that allows menu configuration. Directory Structure System Setup File Structure addonchk.exe Description Installation Utility that is called during installation only. Editor with restricted file access that can be used via the Configuration Manager. 40 October 2004 .exe cfgmedit. if applicable. how the terminal functions when it is in that mode. Figure 1 shows how the terminal normally exits one mode and enters another. If the terminal loses power or is reset.Modes of Operation At any time. like the SOP switch is pressed or the terminal discovers that it is no longer communicating with the network. the terminal abnormally exits from the mode it was in. when the reset or power failure occurred. Wincor Nixdorf terminals operates in one of the following six modes: q q q q q q power-up mode out-of-service mode in-service mode offline mode Service and Operating (supervisor mode) suspend mode The terminal changes from one mode to another when it encounters a specific event. Figure 1: Terminal operation POWER-UP POWER-UP OFFLINE OFFLINE SUPERVISOR SUPERVISOR MODE MODE SUSPEND SUSPEND MODE MODE OUT OF OUT OF SERVICE SERVICE IN SERVICE IN SERVICE The following paragraphs describe how the terminal enters and exits each of the modes and. U25604-J-Z745-1-7600 October 2004 41 . Exiting power-up mode The terminal exits to offline or out-of-service mode when it leaves power-up mode. the Protopas environment and at least the ProCash/NDC. During power-up mode. After all terminal devices are opened the communication framework is waiting for line activity. the terminal can also receive and execute print immediates. Depending on what mode the terminal was in before going out-of-service. If line connection is established. the terminal may perform other functions. During this time. Out-of-service mode The terminal may enter out-of-service mode from any one of the following modes: q q q power-up mode offline mode in-service mode (if the terminal receives an out-of-service command from the network) supervisor mode q The terminal accepts and stores configuration data while it is in out-of-service mode. ProConsult/NDC frameworks. 42 October 2004 U25604-J-Z745-1-7600 . the communication framework sends the power up message as configured to the host. the restart handler starts the WOSA services. startup and shutdown commands from the network.Power-up mode Modes of Operation Power-up mode The terminal enters power-up mode when the terminal is switched on. U25604-J-Z745-1-7600 October 2004 43 . q q q Except when an abnormal exit occurs. the terminal uses the configuration data to make transaction sequence decisions. The terminal exits to supervisor mode when there is an SOP entry on the operator panel. the in-service mode can only be exited from State 000. An abnormal exit occurs.Modes of Operation In-service mode In-service mode The terminal enters in-service mode from any of the following modes: q out-of-service mode (if the terminal receives a startup command from the network) supervisor mode (if the return to previous mode feature is enabled ) offline mode (if communication with the network is restored) q q While in-service. The terminal looses communication with the network. or when the safe door is open. the terminal exits to offline mode. The terminal exits in-service mode under the following conditions: q The terminal receives a shutdown command from the network. the SOP switch is pressed. the terminal exits to out-of-service mode after finishing any customer transactions in progress. While in this mode. q q 44 October 2004 U25604-J-Z745-1-7600 . The terminal enters an idle loop until network communication is restored. the terminal operates as follows: q The terminal displays the user-defined offline screen (screen C01) on the screen. Green status lights in front and on the Operator Panel will be switched off. Suspend mode is entered from the in-service mode if a tampering suspected error has occurred and the specific error of the device class in CCERRMAP is set to Severity 3. The terminal doesn’t accept customer cards. the terminal operates as follows: q The terminal displays the suspend mode screen C05 or C02 (if screen C05 not exists) on the screen. While in this mode.Offline mode Modes of Operation Offline mode The terminal may enter offline mode from any of the following modes: q q q q in-service mode out-of-service mode power-up mode supervisor mode Offline mode is entered from the in-service mode if communication is lost between the network and the terminal. q The terminal exits this mode under the following conditions: q q q communication with the network is restored the terminal enters supervisor mode an abnormal exit occurs Suspend mode The suspend mode feature must be activated in the miscellaneous parameters (see ProCash/NDC ProConsult/NDC Installation manual for details). The terminal responds to all other Transaction Reply command messages with a solicited status message indicating a command reject condition. the terminal sends an unsolicited status message to the network when it enters the operator mode. The terminal accepts Terminal Command messages requesting start-up or shutdown but does not process or reply to them until it exits the supervisor mode. All service and operator functions are described in the manual ProCash/SOP Service & Operating User Guide. While in SOP mode. change passwords and change encryption keys. Refer to section ”Unsolicited Status messages” on page 223 for further information. q q q q U25604-J-Z745-1-7600 October 2004 45 . then upon exiting the SOP. the manager or operator can enable or disable devices or device options for service and maintenance. the terminal processes the last such message received and sends the network a solicited status message indicating a ready condition. The terminal responds to an Terminal Command message requesting configuration information with a solicited status message containing configuration information. If the manager enters the SOP. While in the SOP mode. If the terminal receives any Terminal Command messages requesting startup or shutdown while in the SOP. the terminal responds to network messages as follows: q The terminal processes load command messages and replies with solicited status messages indicating either a ready condition or a command reject condition.Modes of Operation Service and Operating(SOP) The terminal exits this mode under the following conditions: q q q the terminal enters supervisor mode the host sends an in-service or out-of-service command the suspend mode timer has expired (return to previous mode) Service and Operating(SOP) For Wincor Nixdorf terminals the operator uses the Service and Operating to replenish supplies. online help) the Operator Panel has status lights that indicate the terminal status messages can be displayed on the Operator Panel as soon as the situation occurs (in-service. With the SOP itself you can specify special groups with own passwords. such as viewing counters while the terminal remains in service simplifies diagnostics by providing easy-to-understand entry screens and reports test results in understandable phrases a sequencing capability allowing the terminal to perform each command in the sequence without any operator input except an enter keystroke device self tests and operator messages to be included in sequences a simplified status list that compiles supply. the terminal remains out-of-service after exiting SOP. device and fault status on one easy-to-understand report. limiting which commands each group is authorized to use.Service and Operating(SOP) Modes of Operation Service & Operating (operator panel or consumer display) On rearload terminals the operator uses the operator functions via the Operator Panel. out-of-service. 46 October 2004 U25604-J-Z745-1-7600 . context-sensitive. allows the cash position data (balancing data) to be entered into the terminal help text (extensive. Automatic return The automatic return to previous mode feature configures a terminal to automatically return to service after exiting SOP mode. This option can be downloaded with the customization table load command (see ProCash/NDC ProConsult/NDC Installation manual “Optional Parameters (NDC)”). On Frontload terminals the operator can enable the Service & Operating on the consumer screen if he presses the SOP button. Service and Operating provides the following features to enhance operations: q menu selections that are available without device synchronization. door open. If the feature is disabled. door closed) q q q q q q q q Each institution can configure the service and operator functions menu structure to fit the specific needs of the institution with a special tool called SOPCONF. entries are date stamped and all codes are declared in the manual System Messages of CSC-W32. With SOPCONF you can create operator groups. if the terminal was in-service before entering SOP mode. q Front load terminals On front loads the rear balancing functions will be performed in the same way. Refer to the ProCash/NDC-DDC Programmers Reference manual for details regarded to rear balancing step functions. the script framework calls step functions as configured in the step configuration file “LYNXSOP. It also processes the Terminal Command message requesting configuration information. If the rear balancing function has been entered. The operator screen will be displayed 2 or 3 seconds after pressing the button. Then you can select the options with the PIN PAD and softkeys. the terminal accepts load command messages while in-service. The only difference is that supervisor mode is entered on the consumer display. the rear balancing function is part of the User Exit interface and can be called within the “Individual Functions” menu. Rear Balancing On Wincor Nixdorf terminals the rear balancing functions can be performed in two ways: q q on rear load terminals on the operator panel on front load terminals on the screen Start Rear Balancing q Rear load terminals If the ProSop is in use.Modes of Operation Rear Balancing In-service By default. U25604-J-Z745-1-7600 October 2004 47 . You have to open the front door of the safe to reach the button. the rear balancing function is integrated in the step table configuration. The supervisor mode must be activated using the green SOP button on the right-hand side under the customer console in the front.INA”. If the ProCash/NDC-SOP or ProConsult/NDC-SOP is in use. even if a customer is on the terminal. RET_ERROR.Rear Balancing Modes of Operation Customize Rear Balancing functions To build up rear balancing functions for the operator panel or consumer screen. you have to create a step table which is stored in section “.INA” in “C:\PROTOPAS\CONF” can be used to enhance or replace the existing steps against your rear balancing steps.RET_ERROR" 48 October 2004 U25604-J-Z745-1-7600 ..2. Rear Balancing default configuration [REAR_BALANCING] STEP_START = "START" STEP_ABORT = "ABORT" [REAR_BALANCING\ABORT] STEP_FUNC = "APPL_STOP_REAR_BAL" STEP_PARAM = "" JUMP_ON_RC = "RET_ERROR" [REAR_BALANCING\RET_OK] STEP_FUNC = "RETURN" STEP_PARAM = "0" [REAR_BALANCING\RET_ERROR] STEP_FUNC = "RETURN" STEP_PARAM = "1" [REAR_BALANCING\START] STEP_FUNC = "DISPLAY_CONFIRM_MSG" STEP_PARAM = "No Rear Balancing Configured!.1" JUMP_ON_RC = "RET_ERROR. The parameter file “LYNXSOP.\LYNXSOP\ REAR_BALANCING” see ProCash NDC/DDC Programmers Reference for detailed description of step functions and how to create step tables. That means at least.Modes of Operation Dispense Below Zero Dispense Below Zero Since release 1. because the logical cassettes counters never fall down below the low threshold. q q q U25604-J-Z745-1-7600 October 2004 49 . Because ProView is requesting for the WOSA counters and does not get the recalculated counters from ProCash/NDC. Some customers have requested this behavior for host environments where counter actualization is not mandatory after every time when cashout cassettes will be refilled with cash.DLL) is configured. How to configure Dispense Below Zero: Dispense Below Zero can be enabled via following parameter in CUSTOM.2 ProCash/NDC is able to perform dispense operations when the physical cassettes counters become negative. Dispense Below Zero can be used only for cash out systems when the logical WOSA service (BSATM32.PPF: SECTION PARAMETER [CASH_DISPENSER DISPENSE_BELOW_ZERO Please refer to ProCash/NDC ProConsult/NDC Installation manual for detailed description of this parameter. cashout cassettes can be refilled without updating the local cassette counters where dispensing is possible immediately after cassette insertion (and cassette logon via SOP if automatic logon is NOT enabled). Dispense Below Zero cannot be used together with ProView. It is mandatory to install cashout cassettes with a physical LOW sensor to be able to send a “Money Low” unsolicited message to the host. If the ProSop is in use you get counter mismatches between the ProSop counters (received from WOSA) and the recalculated counters in the User Exit function provided by ProCash/NDC. Restrictions: q Dispense Below Zero can be used with ProCash/NDC-SOP only. the counter number of notes remaining in cassette is set to 65535 (FFFF) in the Supply Counters solicited message. (The counters of WOSA would remain zero for all following dispenses. WOSA is not able to handle negative counters.) Temporarily the number of notes added for each cassette is stored in the CMOS. The counters number of notes dispensed and rejected are still maintained with the actual values.Dispense Below Zero Changes of cash counter behaviour: Modes of Operation If Dispense Below Zero is enabled ProCash/NDC handles the internal counters as follows: As long as the number of notes remaining in the cassette is higher or equal than 500 notes. the counters are calculated in the standard way. That has the effect that the WOSA counter will not fall down to zero or below zero in any case. All other counter values are blanked out. The result is that the counters of rejected and dispensed notes get lost. Display or Print Cash Supplies in ProCash/NDC-SOP: For cassettes with negative counters only the number of rejected and dispensed notes are displayed or printed in the Cash Counters supply function. 50 October 2004 U25604-J-Z745-1-7600 . If the remaining counter is lesser than 500 notes. The CMOS counters are used to recalculate back the original counters for the NDC Supply counter message and SOP Cash supply counters. the counter maintained in the CashUnitInfo() structure of WOSA will be encreased with 500 notes via SetCuInfo() call from ProCash/NDC framework dcCdmFW. Send Supply Counters terminal response: If the remaining counter for a cassette becomes negative. etc. U25604-J-Z745-1-7600 October 2004 51 .Miscellaneous Operations ADRS operation ADRS by ProCash/NDC The ProCash/NDC application periodically checks several devices of a self service terminal and the application tries to repair them if neccessary. the application actively tries to repair them via reset. CashIn Module. sends low/out status message to the host Document Printer Checks supply status. This function is called Automatic Device Repair System (ADRS). performs retract Receipt Printer Checks supply status. sends status message to the host. sends low/out status message to the host Journal Printer Checks supply status. for the cash dispenser so called clearing run). During silent service ADRS is called 3 times in a 60 second time cycle. sends low/out status message to the host ADRS by WOSA WOSA (ProDevice) also uses ADRS for the Cash Dispenser device. In a configurable time cycle the status of the device is checked and if neccessary. Deposit Module. The ADRS behavior can be controlled via configuration parameters.) are checked after each consumer transaction. or shutter close commands. sends status message to the host q q q q Deposit Module Checks shutter status. ADRS by Firmware In specific conditions the firmware itself performs ADRS through automatic resets (resp. ADRS methods in ProCash/NDC are implemented for the following devices: q Cash Dispenser Module Checks shutter and transport way status. a reset command is initiated by the WOSA service (Wincor Nixdorf systems only). If status requests to the device are returned with transport jams or device not operational. performs retract or close shutter commands. Especially the shutters and transport ways of input and output devices (Cash Dispenser Module. Please refer to ProCash/NDC Installation Manual and ProDevice parameter specification for ADRS configuration parameters. ADRS operation Miscellaneous Operations 52 October 2004 U25604-J-Z745-1-7600 . for systems of different type or purpose. U25604-J-Z745-1-7600 October 2004 53 . Terminals connected to the network are assigned to distinct groups. control. LUNO (a unique number identifying each terminal). and delimiter characters for different screens which must be shown during different parts of a transaction. q q q Downloaded configuration data are stored in the registry location “LYNXCI” after a "Set Config ID" load command is received. and terminal timer values. FIT Financial Institution Tables entries provide information which is used for identifying which institution has issued a particular card.Configuration Data Configuration data is down-line loaded from the network to each terminal using a series of load command messages. Configuration data is divided into four categories: q States The states table directs the terminal to the tasks to be performed during each part of a transaction. Screens Screen data contains display. the network requests a configuration ID from the terminal. Refer to chapter ”Security Features” on page 175 for details. e. Refer to section ”States” on page 54 for details. From now on the terminal will be loaded automatically with the configuration data of the registry when the application starts up as long as the terminal has not received any new customization data. decoding or encoding of data and for electronic fund transfers. the network will usually send a new configuration load to the terminal. Refer to section ”Miscellaneous Configuration Data” on page 166 for details. A network programmer can create unique configuration data for each group.g. thereby giving each group of terminals its own "personality". Miscellaneous Configuration Data Consists of terminal parameters (capabilities). If the configuration ID sent by the terminal does not match the configuration ID at the network. When power is restored or the terminal is turned on. Refer to section ”Screens” on page 153 for details. Each state table of the same state type is a different version of that state providing the same type of functions. inquiry or other) and later they have to select the type of account. The terminal should always return to a close state after the consumer’s transaction(s) have been completed. The terminal requires the repeated use. in any order. depending on the transaction that the costumer has requested. For instance. 3. The use of these state types. but used in a different manner. A state table is 25 characters long (first entry. which is one character long. The other eight entries are used to specify the actions performed (such as screen displayed. of some states. in different ways. The different state tables are specified by a three-digit decimal number (000 through 999). The terminal may use one state type several times while processing a transaction. buffers used and next state table) and are three characters long. other state types might not be used at all. State table 000 is usually a card read state. This range allows up to 1000 different state tables. defines terminal operation. The first entry in a state table is a single character identifying the type of state (ASCII graphic character). State table 000 is the first state table that the terminal is in when it enters in-service mode. 54 October 2004 U25604-J-Z745-1-7600 . Both tasks are performed using different versions of the select function state. For example. Each state table contains nine entries. 1. withdrawal. Each state type can have one or more state tables associated with it.States Configuration Data States The states configuration data is down-line loaded using the States Table Load command message (refer to section ”State Tables Load” on page 239). the consumers have to select the type of transaction (deposit. plus eight three-digit entries). Only those subroutines and hardware components (such as screen and keyboard) that facilitate function selection are used. while the terminal is in the select function state the terminal is dedicated to the task of prompting the consumer to select a function and recognizing the key (function) selected. Each state is associated with a specific task. 2. the input string is terminated. a Preset Operation Code Buffer state will usually be the next state. The next state depends on the customer’s input. or times-out during data entry. The next state varies depending on the customer’s selection. D E Amount Entry F Amount Check G Information Entry H U25604-J-Z745-1-7600 October 2004 55 . displays that amount on the screen. If the customer presses the cancel key. Table 5: State summary States State Name Card Read PIN Entry Unlock Envelope Dispenser Preset Operation Code Buffer FDK Selection State Description Type A B C Reads the magnetic stripe from the ID card and then usually indicates a PIN entry state as the next state. Reads in a variable-length string of numerical keys and stores that data in a general purpose buffer. the terminal displays the data on the screen. If the amount entered by the customer is not a whole amount. Reads the entered amount. The key codes are stored in the operation code buffer. an amount check state will normally be the next state. Verifies that the amount entered is a whole amount (zero cents). Otherwise.Configuration Data A summary of all the state types is shown in the following tables. a Preset Operation Code Buffer state will typically be the next state. Optionally. Otherwise. Clears and sets any or all 8 bytes of the operation code buffer. Reads the code of each operation key pressed by the customer. an operation key. If a withdrawal transaction is being processed. Reads the PIN number entered by the customer and verifies that the PIN entered is valid. After this state the terminal immediately goes to the next state. the next state is always determined by the network configuration. and stores it in the amount buffer. Used to modify selection paths based on FIT table entry and institution type. The next state depends on the network response. Typically. if the application requires that the number of the card read state be something other than 000. Returns or retains the customer’s card and optionally issues a printed acknowledgment form to the customer. The terminal can use customized state tables for the customers of a specific institution. During this state. The Skip Step is used to skip states which are not supported by ProCash/NDC or ProConsult/NDC. This card read state is used. The terminal can provide different functions to different customers depending on the customer’s institution. The extension of this state checks for warning conditions und uses the specified next state exit. General Purpose buffer B or C buffer. the terminal writes the contents of the track 3 data buffer onto the magnetic stripe of a card Same functions as B state. and stores it in the Amount buffer. The Smart FIT Check state performs a FIT check with the chip data that is read from the chip of a smart card. It goes to the specified next state depending on devices which have a fatal condition.States Configuration Data State Name Transaction Request State Description Type I Sends a Transaction Request message to the network and executes the Transaction Reply commands received from the network. displays it on the screen. The Hardware Fitness state checks for fatal error condition of the terminal devices. Close J FIT Switch K Card Write Enhanced PIN Entry L M Card read T (Non-000 state applications) Hardware Fitness h Smart FIT Check Skip Step Enhanced Amount Entry k 56 October 2004 U25604-J-Z745-1-7600 . the next state table used is 000 (a card read state preparing the terminal for the next customer). but including updating track data on the ID card. R Reads the entered amount. The Extension state extends the functions of state ‘S’. The Extension state can be activated in the extension state number field of the state. This state reads the FDK selected by the cardholder. ‘T’. FIT switch state with enhanced number of next states depending on the specified switch index in the FIT table. In this state one set of state tables can be used to display screens in different languages within the same transaction. This state allows the consumer to change the PIN. This state allows the consumer to set the audio volume for the played message and to switch audio channels. ‘X’.Configuration Data States State Name State Description Type In this state the flow of a transaction is switched on whether a language code is present in the card data or not. This is determined by a code on the cardholder’s card. This state reads the data buffer from the 8 FDK selection state to identify which next state the terminal should go. stores the key code in an FDK buffer for use by an FDK switch state. Language S Code Switch Language Select from Card FDK Switch V W FDK Information 8 FDK Selection X Y Customer b Selected PIN Audio Control Expanded FIT Switch Extension i ’_’ Z U25604-J-Z745-1-7600 October 2004 57 . This state translates the FDK selected by the cardholder into a value that is placed in the specified buffer for use by an FDK switch state. ‘k’ and ‘Y’. and updates the operation code buffer. \LYNXPAR\STATE_MAP” The following table shows. ProConsult/NDC steps belonging to NDC states State Type A B C D E F G H I J K L M N Step DC_CARD_READ DC_PIN_ENTRY DC_DISPENSE_ENVELOPE DC_PRESET_OP_CODE DC_FDK_SELECT4 DC_AMOUNT_ENTRY DC_WHOLE_DOLLAR_CHECK DC_INFORMATION_ENTRY DC_TRAN_REQUEST DC_CLOSE_TRAN DC_FIT_SWITCH DC_WRITE_CARD DC_ENH_PIN_ENTRY DC_CAMERA_CONTROL State Type S T V W X Y Z ’_’ b i P R k all states Step NDC_LANGUAGE_SWITCH NDC_CARD_PIN NDC_CARD_LANGUAGE NDC_FDK_SWITCH NDC_FDK_INFO_ENTRY NDC_FDK_SELECT NDC_EXT NDC_EXP_FIT_SWITCH NDC_CUST_SEL_PIN NDC_AUDIO_CONTROL NDC_EXP_FIT_SWITCH NDC_ENH_AMOUNT_ENTRY DC_HARDWARE_FITNESS [1] DC_NEXT_X (X = 1-8) [1] [1] - Wincor Nixdorf specific state 58 October 2004 U25604-J-Z745-1-7600 .States Configuration Data Steps processing ProCash/NDC or ProConsult/NDC uses step oriented functions for each state. which NDC state is assigned to a ProCash/NDC or ProConsult/NDC step: Table 6: ProCash/NDC. Every downloaded state is assigned to a specific ProCash/NDC or ProConsult/NDC step.. The step assignment is stored in the Windows registry location “. This state table is normally assigned to the state number 000. The terminal enters state number 000 automatically when placed in-service.Configuration Data States Card Read State (A) The Card Read state is usually the first state used during transaction processing. The Card Read state table performs the following functions: q q q q identifies the number of the screen displayed for prompting card entry identifies the screen displayed after a misread defines the card track(s) from which data is read contains a flag for the card return feature (immediately or at the end of the transaction) indicates the next state number for cards that are read properly scans the FIT to obtain a match on the financial institution number tells the terminal the next state to go to if there is no FIT match q q q Table 7: Card Read state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number correct read next state number error (misread) screen number read condition 1 read condition 2 read condition 3 card return flag no FIT match next state number U25604-J-Z745-1-7600 October 2004 59 . 256-999 The number of the state the terminal enters after the customer’s card is read properly. 60 October 2004 U25604-J-Z745-1-7600 . Error (misread) screen number Entry number: 4 Valid range: Description: 000-999 This is the number of the screen displayed if the card is not read properly. Good read next state number Entry number: 3 Valid range: Description: 000-254. this screen will prompt the customer to check that the card is inserted correctly and to reinsert the card. Normally.States The card read (A) state entries are defined as follows: State type Entry number: 1 Valid range: Description: A Configuration Data This state ID identifies this state table as a Card Read state table. Screen number Entry number: 2 Valid range: Description: 000-999 This is the number of the screen which prompts the customer to insert a card. This screen is displayed while the terminal is awaiting card entry. Normally the next state is a PIN entry state type. This one is used if read condition 1 cannot be done. This is the second read condition used. 6 and 7) that tell the terminal which card track(s) must be read. Refer to table “Card Read state entries” for the definition of the card read conditions.Configuration Data Read condition 1 Entry number: 5 Valid range: Description: 001-015 States This is one of the three entries (used with entry no. read condition 2 is used next. Refer to table “Card Read state entries” for the definition of the card read conditions.return card upon transaction completion U25604-J-Z745-1-7600 October 2004 61 . Refer to table “Card Read state entries” for the definition of the card read conditions. This is the first read condition. 5 and 7) that tell the terminal which card track(s) must be read. The valid values are as follows: 000 . this read condition is used. If read condition 2 cannot be met. If this condition cannot be met. read condition 3 is used.return card immediately 001 . 5 and 6) that tell the terminal which card track(s) must be read. Card return flag Entry number: 8 Valid range: Description: 000-001 This entry tells the terminal whether the card should be returned immediately or upon transaction completion. If neither read condition 1 or read condition 2 can be met. Read condition 2 Entry number: 6 Valid range: Description: 001-015 This is one of the three entries (used with entry no. Read condition 3 Entry number: 7 Valid range: Description: 001-015 This is one of the three entries (used with entry no. Table 8: Read condition entry definitions Required track(s) Card read table Entry 5 (read condition 1) 1 only 004 2 only 002 3 only 001 1 and 2 006 1 and 3 005 2 and 3 003 1 and 2 and 3 007 2 or 3 002 1 or 3 004 1 or 2 004 1 or2or3 004 (1 and 2) or (1 and 3) 006 (2 and 1) or (2 and 3) 006 (3 and 1) or (3 and 2) 005 1 or (2 and 3) 004 2 or (1 and 3) 002 3 or (1 and 2) 001 Chip connect only 008 3 and chip connect 009 2 and chip connect 010 2. 3 and chip connect 011 1 and chip connect 012 1. 3 and chip connect 013 1. 2 and chip connect 014 1.States No FIT match next state number Entry number: 9 Valid range: Description: 000-254. 3 and chip connect 015 Card read table Entry 6 (read condition 2) 004 002 001 006 005 003 007 001 001 002 002 005 003 003 003 005 006 008 009 010 011 012 013 014 015 Card read table Entry 7 (read condition 3) 004 002 001 006 005 003 007 001 001 002 001 005 003 003 003 005 006 008 009 010 011 012 013 014 015 62 October 2004 U25604-J-Z745-1-7600 . 256-999 Configuration Data The number of the state the terminal enters if the FIT number on the card does not match that of any member institution. 2. U25604-J-Z745-1-7600 October 2004 63 . Otherwise. Otherwise. If read condition 2 is satisfied. If read condition 3 is satisfied. the good read next state number entry (table entry 3) is taken. Otherwise. read condition 2 is attempted. read condition 3 is attempted. the good read next state number entry (table entry 3) is taken.Configuration Data Short desciption to Table 8: States If read condition 1 is satisfied. the card is ejected and the error screen number (table entry 4) is displayed. the good read next state number entry (table entry 3) is taken. refer to chapter ”Security Features” on page 175. If local PIN verification is used. FIT determines whether the terminal performs PIN verification (local PIN verification) or whether this is done by the network (remote PIN verification). correct PIN next state number local PIN check. the terminal does not use state entry 5. If remote PIN verification is used. error screen number remote PIN check. next state number local PIN check. maximum bad PIN’s next state number local PIN check. maximum PIN attempts The PIN Entry (B) state entries are defined as follows: State type Entry number: 1 Valid range: Description: B This state ID identifies this state table as a PIN Entry state table. the terminal does not use state entry 8.States Configuration Data PIN Entry State (B) The PIN Entry state prompts the customer to enter the PIN and displays an X for each PIN digit entered. 64 October 2004 U25604-J-Z745-1-7600 . For details on each PIN verification method. Table 9: PIN Entry state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number local PIN check. Cancel next state number Entry number: 4 Valid range: Description: 000-254. This screen must position the cursor at the beginning of the area where the Xs are displayed. The number of digits to be checked are specified by FIT field PCKLN.Configuration Data Screen number Entry number: 2 Valid range: Description: 000-999 States This is the number of the screen display that prompts the customer to enter the PIN. This screen is displayed when the terminal enters the PIN entry state. U25604-J-Z745-1-7600 October 2004 65 . 256-999 The number of the state to which the terminal proceeds if the customer fails to enter the PIN within the specified time limit. Local PIN check. Enter 255 to deactivate the time-out function. Entering 255 keeps the terminal in this state until an operation key is pressed. 256-999 The number of the state to which the terminal proceeds after it verifies that the customer entered the correct PIN (if local PIN check). Normally the next state is a Pre-Set Operation Code Buffer state. 256-999 This is the number of the state to which the terminal proceeds if the customer presses the cancel key. Time-out next state number Entry number: 3 Valid range: Description: 000-254. good PIN next state number Entry number: 5 Valid range: Description: 000-254. This screen must position the screen cursor at the beginning of the area in which the Xs are displayed. Local PIN check.) 66 October 2004 U25604-J-Z745-1-7600 . Typically used in the ’M’ state. Local PIN check. Remote PIN check. 256-999 Description: The number of the state to which the terminal proceeds after the customer incorrectly enters the PIN the number of times specified by state entry 9. maximum bad PIN’s next state number Entry number: 6 Vollud data range:000-254. This screen is displayed each time the customer enters an incorrect PIN until the retry value is reached as specified by state entry 9 (or by the card).States Configuration Data Local PIN check. next state number Entry number: 8 Valid range: Description: 000-254. Normally. (This can be overridden by an entry on the card if such is specified by the FIT. maximum PIN attempts Entry number: 9 Valid range: Description: 000-009 This entry specifies the maximum number of times that a customer can enter an incorrect PIN before the terminal goes to the state specified by state entry 6. 256-999 The number of the state to which the terminal proceeds if no local PIN check is specified in FIT. error screen number Entry number: 7 Valid range: Description: 000-999 The number of the screen display that prompts the customer to enter the PIN again. the next state is a close state. If checking is local. It differs from the PIN entry state (B) in the number of retries. The state will prompt for the new PIN twice and will take a good exit if both are the same and local PIN check is enabled. The ’CLEAR’ key clears all digits. the exit will be taken when the two new PIN’s have been built into the PIN blocks for transmitting. If the number of digits entered is less than the value specified in the FIT entry PMXPN the cardholder must press FDK A or ’ENTER’ key on the facia keyboard after the last digit entered . The cardholder PIN is entered on the facia keyboard and consists of four to sixteen digits. Table 10: Customer Selectable PIN state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type first entry screen number time-out next state number cancel next state number good next state number CSP fail next state number second entry screen number mismatch first entry screen number extension state number U25604-J-Z745-1-7600 October 2004 67 . If the FIT specifies that short PIN entry is to be tested for.Configuration Data States Customer Selectable PIN State (b) This state allows the cardholder to input a new PIN. short PIN’s will be regarded as one try against the limit specified in the state table. The screen association for this state is derived from screen specified in table entry 2. If checking is enabled and the two PIN’s entered are not the same the cardholder wil be asked to re-enter the Customer Selectable PIN (CSP) and the state will not exit. Good next state number Entry number: 5 Valid range: Description: 000-254. Time-out next state number Entry number: 3 Valid range: Description: 000-254. 256-999 State number to which the terminal goes if the cardholder enters a matching pair of new PIN values. 68 October 2004 U25604-J-Z745-1-7600 . 256-999 State number to which the terminal goes if the cardholder does not make a CSP entry within the specified time limit. Enter 255 if the time-out function is not required.States Configuration Data The Customer Selectable PIN (b) state entries are defined as follows: State type Entry number: 1 Valid range: Description: b This state ID identifies this state table is a Customer Selectable PIN state table. 256-999 State number to which the terminal goes if the cardholder presses the ’CANCEL’ key to stop the CSP transaction. First entry screen number Entry number: 2 Valid range: Description: 000-999 Display screen that prompts the cardholder to enter the PIN the first time. Cancel next state number Entry number: 4 Valid range: Description: 000-254. 256-999 State number of the extension state. No FIT match 2. PIN block generation fails. 3. Cardholder tampering is detected. 256-999 States State number to which the terminal goes if the cardholder fails to enter a matching pair of new PIN digits or the maximum number of retries for local PIN checking is reached. Second entry screen number Entry number: 7 Valid range: Description: 000-999 Display screen used to ask for confirmation of the CSP. Mismatch first entry screen number Entry number: 8 Valid range: Description: 000-999 Displays a new screen that replaces the screen for table entry 2 on each attempt after a CSP pair attempt did not match or an error has occurred and there are still further retries allowed. This state will also be taken if: 1. Extension state number Entry number: 9 Valid range: Description: 000-254.Configuration Data CSP fail next state number Entry number: 6 Valid range: Description: 000-254. U25604-J-Z745-1-7600 October 2004 69 . Use local verification of new PIN pair attempts Entry number: 3 Valid range: Description: 000-001 Specifies which attempts are to be verified locally: 0 . Number of attempts allowed to enter a matching CSP pair Entry number: 2 Valid range: Description: 000-010 Limits the number of attempts the cardholder may make to select a new PIN.Verify both attempts locally.Do not verify locally 1 . Table 11: Extension state entries Entry 1 2 3 4-9 Definition state type number of attempts allowed to enter a matching CSP pair use local verification of new PIN pair attempts reserved. A zero entry means no limit. must be ’000’ The Extension state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies that this state table is an Extension state.States Configuration Data Extension to state (b) This state extends the Customer selected PIN state regarding number of PIN entry attempts and type of PIN verification. Result available in transaction request field ’U’. 70 October 2004 U25604-J-Z745-1-7600 . Next state number Entry number: 2 Valid range: Description: 000-511 The number of the state to which the terminal proceeds after entering state C.Configuration Data States Envelope Dispense (C) State The Envelope Dispense (C) state tells the terminal how to process a deposit operation. Refer to ProCash/NDC ProConsult/NDC Installation manual for detailed parameter description. If the local parameter “DISPENSE_ENVELOPE” is disabled. the envelope is dispensed within the envelope dispense (C) state. Table 12: Envelope Deposit (C) state entries Entry 1 2 3-9 Definition state type next state number reserved. If there are still enough envelopes in the deposit module and the local parameter “DISPENSE_ENVELOPE” is enabled. the Envelope Dispense (C) state immediately enters the next state exit without an envelope dispense operation. Envelope dispensing takes place in the deposit function of the transaction reply. must be ’000’ The Envelope Deposit (C) state entries are defined as follows: State type Entry number: 1 Valid range: Description: C This state ID identifies this state table as an Envelope Deposit state. U25604-J-Z745-1-7600 October 2004 71 . Pre-set selected bytes of the operation code buffer with A. B. 72 October 2004 U25604-J-Z745-1-7600 . Bit 0 of the mask represents the first byte. The Pre-Set Operation Code Buffer state can do any combination of the following: q Clear the operation code buffer or clear selected bytes of the operation code buffer. G. H or I q Each bit of the masks in this state represents a byte (buffer position) in the operation code buffer. C. bit 7 of the mask represents the eighth byte. Table 13: Pre-Set Operation Code Buffer state table Entry 1 2 3 4 5 6 7 8 9 Definition state type next state number clear mask A preset mask B preset mask C preset mask D preset mask reserved extension state number The Pre-Set Operation Code Buffer (D) state entries are defined as follows: State type Entry number: 1 Valid range: Description: D This state ID identifies this state table as a Pre-Set Operation Code Buffer state table.States Configuration Data Pre-Set Operation Code Buffer State (D) The operation code buffer is eight bytes long. or D and F. If a bit is enabled (one). Each bit relates to a byte in the operation code buffer. B Preset mask Entry number: 5 Valid range: Description: 000-255 Specifies bytes of operation codeoperation code buffer buffer to be set to B. the corresponding entry is cleared. Set this entry to 255 if none of the operation code buffer positions are to be cleared. the corresponding entry is unchanged. If a bit is enabled (one). bit 7 relates to the eighth entry. Bit 0 relates to the first entry. If a bit is enabled (one). bit 7 relates to the eighth entry. the corresponding entry is set to B. If a bit is disabled (zero). Clear mask Entry number: 3 Valid range: Description: 000-255 Specifies bytes of operation code buffer to be cleared to graphic "space. Bit 0 relates to the first entry. Bit 0 relates to the first entry." Each bit relates to a byte in the operation code buffer. bit 7 relates to the eighth entry. the corresponding entry is unchanged. Each bit relates to a byte in the operation code buffer. U25604-J-Z745-1-7600 October 2004 73 . If a bit is disabled (zero). the corresponding entry is set to A. A Preset mask Entry number: 4 Valid range: Description: 000-255 Specifies bytes of operation code buffer to be set to A. the corresponding entry is unchanged. If a bit is not set (zero).Configuration Data Next state number Entry number: 2 Valid range: Description: 000-254. 256-999 States The number of the state to which the terminal proceeds after clearing or presetting the operation code buffer. Each bit relates to a byte in the operation code buffer. Reserved Entry number: 8 Valid range: Description: 000 Entry 8 is reserved and must be 000. D Preset mask Entry number: 7 Valid range: Description: 000-255 Specifies bytes of operation code buffer to be set to D. bit 7 relates to the eighth entry.States C Preset mask Entry number: 6 Valid range: Description: 000-255 Configuration Data Specifies bytes of operation code buffer to be set to C. If a bit is disabled (zero). the corresponding entry is set to C. Bit 0 relates to the first entry. If a bit is disabled (zero). Extension State number Entry number: 9 Valid range: Description: 000-254 or 256-999 State number of the extension state containing information on how the other operation codes are preset. 74 October 2004 U25604-J-Z745-1-7600 . the corresponding entry is unchanged. bit 7 relates to the eighth entry. the corresponding entry is unchanged. Bit 0 relates to the first entry. If a bit is enabled (one). the corresponding entry is set to D. Each bit relates to a byte in the operation code buffer. If a bit is enabled (one). Configuration Data Clear mask (entry 3) example Start with an operation code buffer that looks like the following: Buffer Bit Pos Weight B 0 1 _ 1 2 _ 2 4 C 3 8 _ 4 16 _ 5 32 D 6 64 _ 7 128 States To clear buffer position 6 (byte 6). B. the resultant operation code buffer would appear as follows: Buffer Bit pos B 0 _ 1 _ 2 C 3 _ 4 _ 5 _ 6 _ 7 A. Buffer Bit pos Positions not cleared Weights not cleared B _ 0 1 X X 1 + 2 + 4 _ 2 X + 8 + C 3 X 16 + _ 4 X 32 + _ D 5 6 X 128 = 191 _ 7 X With 191 entered in entry 3. D preset masks (entries 4-7) example Assume that you want to set the operation code buffer positions as follows: q q q q positions 0 and 2 to A positions 1 and 5 to B position 3 to C positions 4 and 7 to D The buffer would appear as follows: Buffer Bit pos Weight A 0 1 B 1 2 A 2 4 C 3 8 D 4 16 B 5 32 _ 6 64 D 7 128 The entries would have to be set as follows: q q q q entry 4 (A preset mask) entry 5 (B preset mask) entry 6 (C preset mask) entry 7 (D preset mask) - 1+4 2 + 32 8 16 + 128 = 005 = 034 = 008 = 144 U25604-J-Z745-1-7600 October 2004 75 . C. add the weights of the positions that you do not want to clear and put that result in the clear mask entry (entry 3). Bit 0 relates to the first entry. the corresponding entry is unchanged. If a bit is disabled (zero). F Preset mask Entry number: 2 Valid range: Description: 000-255 Specifies bytes of operation code buffer to be set to F. Each bit relates to a byte in the operation code buffer. G. the corresponding entry is set to F. Table 14: Preset operation code buffer Extension state table Entry 1 2 3 4 5 6-9 Definition state type F preset mask G preset mask H preset mask I preset mask reserved must be 000 The Pre-Set Operation Code Buffer Extension (Z) state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as an Pre-Set Operation Code Buffer Extension state. H or I. If a bit is enabled (one). bit 7 relates to the eighth entry.States Configuration Data Extension to State (D) The extension to state (D) allows presetting the operation code buffer with F. 76 October 2004 U25604-J-Z745-1-7600 . If a bit is enabled (one). Each bit relates to a byte in the operation code buffer. If a bit is disabled (zero). Each bit relates to a byte in the operation code buffer. Bit 0 relates to the first entry. bit 7 relates to the eighth entry. Bit 0 relates to the first entry. bit 7 relates to the eighth entry. If a bit is disabled (zero). the corresponding entry is unchanged. the corresponding entry is set to H.Configuration Data G Preset mask Entry number: 3 Valid range: Description: 000-255 States Specifies bytes of operation code buffer to be set to G. the corresponding entry is set to G. If a bit is enabled (one). I Preset mask Entry number: 5 Valid range: Description: 000-255 Specifies bytes of operation code buffer to be set to I. bit 7 relates to the eighth entry. H Preset mask Entry number: 4 Valid range: Description: 000-255 Specifies bytes of operation code buffer to be set to H. the corresponding entry is unchanged. the corresponding entry is set to I. Each bit relates to a byte in the operation code buffer. If a bit is enabled (one). the corresponding entry is unchanged. Bit 0 relates to the first entry. U25604-J-Z745-1-7600 October 2004 77 . If a bit is disabled (zero). This state permits the customer to select one function from up to four functions displayed on the screen. by pressing one of the active operation keys. The state table data for this state type defines which of the four operation keys are to be active during this state. 78 October 2004 U25604-J-Z745-1-7600 . and then advances to the next state.States Configuration Data Four FDK Selection Function State (E) This state reads the operation key that has been pressed by the cardholder. Table 15: Four FDK Select Function state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number operation key A next state number operation key B next state number operation key C next state number operation key D next state number operation code buffer location The Four FDK Selection Function (E) state entries are defined as follows: State type Entry number: 1 Valid range: Description: E This state ID identifies this state table as a Function Selection state table. stores the key code in the operation code buffer. U25604-J-Z745-1-7600 October 2004 79 . Operation key B next state number Entry number: 6 Valid range: Description: 000-254. Cancel next state number Entry number: 4 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer fails to make the selection within the specified time limit (specify "255" if the time-out function is not used).. 6. etc. This screen is displayed upon entry into the selection function state and must be aligned with the active operation keys (table entry 5. 7. and 8) for proper operation. account names. 256-999 The state number to which the terminal proceeds if the customer presses the A operation key (specify "255" to deactivate the A operation key during this state). 256-999 The state number to which the terminal proceeds if the customer presses the B operation key (specify "255" to deactivate the B operation key during this state).Configuration Data Screen number Entry number: 2 Valid range: Description: 000-999 States The number of the display screen which prompts the customer to choose between transaction types. Operation key A next state number Entry number: 5 Valid range: Description: 000-254. Time-out next state number Entry number: 3 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the cancel key instead of an operation key. 000-254. 256-999 Description: The state number to which the terminal proceeds if the customer presses the D operation key (specify "255" to deactivate the D operation key during this state). Operation key D next state number Entry number: 8 Valid range. 256-999 Configuration Data The state number to which the terminal proceeds if the customer presses the C operation key (specify "255" to deactivate the C operation key during this state). The network down-line loads the following data to select the indicated buffer byte: 000 = buffer 001 = buffer 002 = buffer 003 = buffer 004 = buffer 005 = buffer 006 = buffer 007 = buffer position 0 position 1 position 2 position 3 position 4 position 5 position 6 position 7 Buffer positions are as follows: ________ 01234567 80 October 2004 U25604-J-Z745-1-7600 . Operation code buffer location Entry number: 9 Valid range: Description: 000-007 Specifies the operation code buffer byte in which the key code for the selected operation key is to be stored.States Operation key C next state number Entry number: 7 Valid range: Description: 000-254. U25604-J-Z745-1-7600 October 2004 81 . Screen number Entry number: 2 Valid range: Description: 000-999 Number of display screen that prompts an amount entry.Configuration Data States Amount Entry State (F) This state reads the amount entered by the consumer. This buffer is 8 or 12 bytes long. the operation keys are used by the consumer to indicate whether the displayed amount is either correct or incorrect. displays it on the screen and saves it in the amount buffer. In the amount entry state. Table 16: Amount Entry state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number operation key A next state number operation key B next state number operation key C next state number operation key D next state number display amount screen number The Amount Entry (F) state entries are defined as follows: State type Entry number: 1 Valid range: Description: F This state ID identifies this state table as an Amount Entry state table. This screen is displayed upon entry into the amount entry state. Value "255" deactivates the CANCEL key during this state. Operation key B next state number Entry number: 6 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the A operation key. Cancel next state number Entry number: 4 Valid range: Description: 000-254. Value "255" deactivates the B operation key during this state.States Time-out next state number Entry number: 3 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the B operation key. Value "255" deactivates the A operation key during this state. 82 October 2004 U25604-J-Z745-1-7600 . Operation key C next state number Entry number: 7 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the C operation key. Operation key A next state number Entry number: 5 Valid range: Description: 000-254. Value "255" deactivates the C operation key during this state. 256-999 Configuration Data The state number to which the terminal proceeds if the customer fails to enter the amount within the specified time limit (specify "255" if the time-out function is not used). 256-999 The state number to which the terminal proceeds if the customer presses the cancel key before pressing an operation key. This is space filled until the required start position for the currency character is reached. Normally one operation key is used to indicate whether the amount entry is correct and another is used to indicate whether it is incorrect. The other operation keys are inactive.00 (where b = space) U25604-J-Z745-1-7600 October 2004 83 . Display amount screen number Entry number: 9 Valid range: Description: 000-999 Overlay screen number that sets the screen cursor position. 256-999 States The state number to which the terminal proceeds if the customer presses the D operation key.00 (where b = space) Default echo field for twelve digits: bbbbbbbbb$ 0. Value "255" deactivates the D operation key during this state.Configuration Data Operation key D next state number Entry number: 8 Valid range: Description: 000-254. This screen optionally defines the initial display format prior consumer amount entry. The cursor should be set on the lefthand side of the echo field on the screen. Default echo field for eight digits: bbbbb$ 0. Table 17: Amount Check state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type whole amount entry next state number non-whole amount entry next state number buffer to be checked zero entry next state number (if table entry 8 is zero) or integer multiple value (if table entry 8 is non zero) number of decimal places currency type amount check condition reserved must be zero The Amount Check (G) state entries are defined as follows: State type Entry number: 1 Valid range: Description: G This state ID identifies this state table as a amount check state table.States Configuration Data Amount Check State (G) This state checks to see if the amount entered is a whole amount (zero cents). Central must have downloaded the Dispenser Currency Cassette Mapping Table. 84 October 2004 U25604-J-Z745-1-7600 . processing will proceed with non-whole amount entry next state number. When checking that an amount is dispensable. or a currency type identified in table entry 7 is not present in the table. If this table has not been downloaded. This state should follow the amount entry function state when a withdrawal transaction is being performed. If table entry 8 is non-zero: Integer multiple value used in checking specified buffer. Non-whole amount entry next state number Entry number: 3 Valid range: Description: 000-999 The state number to which the terminal proceeds upon finding a cents value other than 00 cents in the amount entry.general purpose buffer C Zero entry next state number Integer Multiple Value Entry number: 5 Valid range: Description: 000-999 If table entry 8 is zero: The state number to which the terminal proceeds. U25604-J-Z745-1-7600 October 2004 85 . to check that the specified buffer contains a multiple of the minimum denomination $5.Configuration Data Whole amount entry next state number Entry number: 2 Valid range: Description: 000-999 States The state number to which the terminal proceeds upon finding 00 (zero cents) value in the amount entry.amount buffer 001 . this field would be set to '005'. This field is ignored if table entry 8 is not ‘002’. For example. if the consumer enters zero amount or does not enter any value. Buffer to be checked Entry number: 4 Valid range: Description: 000-002 This field specifies which buffer is to be checked: 000 .general purpose buffer B 002 . For example. 86 October 2004 U25604-J-Z745-1-7600 . the state evaluates whether the value is a whole number multiple of the value identified in table entry 5. When this entry is set to 003.States Number of decimal places Entry number: 6 Valid range: Description: 000-004 Configuration Data Number of decimal places used in specified buffer. so has 002 decimal places. When this entry is set to 000. This field is ignored if table entry 8 is not '003'. taking into account the currency type required (table entry 7). the state does not use state parameters 5 to 9. Reserved Entry number: 9 Valid range: Description: 000 Entry 9 is reserved and must be 000. All conditions except condition ‘000’ take account of the decimal point location via the value in table entry 6. the state evaluates whether the value is dispensable by the terminal. currency type denominations available. Amount check condition Entry number: 8 Valid range: Description: 000-003 If the condition being checked evaluates to 'true' then processing will proceed to the next state identified in table entry 2. dispenser status and cassette status. to enable backwards compatibility. otherwise processing will proceed to the next state identified in table entry 3. Currency type Entry number: 7 Valid range: Description: 001-255 Currency type of amount in specified buffer. the state evaluates whether the value to the right of the decimal point position is zero. When this entry is set to 001. Used in conjunction with the Dispenser Currency Cassette Mapping Table. When this entry is set to 002. $5 is sent as 500 cents. All conditions check the buffer indicated by table entry 4. then the buffer contains no data. Table 18: Information Entry state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number operation key A next state number operation key B next state number operation key C next state number operation key D next state number buffer and display parameters The Information Entry (H) state entries are defined as follows: State type Entry number: 1 Valid range: Description: H This state ID identifies this state table as an information entry state table.Configuration Data States Information Entry State (H) This state reads in a variable-length string of numeric keys. When the terminal enters this state. U25604-J-Z745-1-7600 October 2004 87 . and displays either the data or ‘X’ for each numeric key pressed. Maximum length is 32 bytes. saves the data in one of two general purpose buffers (see table entry 9). or a time-out. The input string is terminated by an operation key. General purpose buffers B and C are variable in length. cancel key. If no keys are depressed. the specified buffer contains only the data from the depressed numeric keys. This screen is displayed upon entry into the information entry state and must leave the cursor at the beginning of the data or X display area. Cancel next state number Entry number: 4 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the B operation key. Operation key A next state number Entry number: 5 Valid range: Description: 000-254. Operation key B next state number Entry number: 6 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the cancel key before pressing an operation key. Value "255" disables the time-out function. 256-999 The state number to which the terminal proceeds if the customer presses the A operation key. 88 October 2004 U25604-J-Z745-1-7600 . Value "255" deactivates the A operation key during this state. Value "255’ deactivates the B operation key during this state. Time-out next state number Entry number: 3 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer fails to respond to the CRT message within a specified time limit.States Screen number Entry number: 2 Valid range: Description: 000-999 Configuration Data The number of the display screen that prompts key entry from the customer. U25604-J-Z745-1-7600 October 2004 89 . 32 digits). The valid characters are as follows: xx0 = xx1 = xx2 = xx3 = display X for each numeric key pressed. display data as entered. Value "255" deactivates the C operation key during this state. display data as entered. 000-323 Description: This entry specifies whether the actual data entered or X is to be displayed. store keys in general purpose buffer C (max. 32 digits). 32 digits). The default buffer size of 32 digits can be decreased if the first two digits have a non zero value up to the maximum of 32. Value "255" deactivates the D operation key during this state. store keys in general purpose buffer C (max. 32 digits). Operation key D next state number Entry number: 8 Valid range: Description: 000-254. beginning at the current cursor position. store keys in general purpose buffer B (max. display X for each numeric key pressed. store keys in general purpose buffer B (max. 12 digits. 256-999 States The state number to which the terminal proceeds if the customer presses the C operation key. This entry also specifies which general purpose buffer (B or C) is used for storing the numeric data input and how many digits can be entered. store keys in general purpose buffer B with max.Configuration Data Operation key C next state number Entry number: 7 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the D operation key. Buffer and display parameters Entry number: 9 Valid range. Set a buffer limit example: 123 = display data as entered. 256-999) The Transaction Request (I) state entries are defined as follows: State type Entry number: 1 Valid range: Description: I This state ID identifies this state table as a transaction request state table. transmits the transaction request message to the network. When the network responds with a Transaction Reply command message. Table 19: Transaction Request state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number network response time out next state number send track 2 data send track 1.States Configuration Data Transaction Request State (I) The Transaction Request state tells the terminal what information to include in the transaction request message. If the network does not respond with a Transaction Reply command message within the time specified by timer 03 (section “Timer Data” on page 167). track 3 send operation code buffer send amount buffer send PIN buffer (Buffer A) data / Select Extended format send general purpose buffer(s) B and/or C or Extension State Number (Range 000-254. the terminal goes to the state specified in entry 3 of this state. the terminal executes the Transaction Reply command message and goes to the next state specified in the Transaction Reply command message. 90 October 2004 U25604-J-Z745-1-7600 . and waits for the network response. The valid values are as follows: 000 . The valid values are as follows: 000 .send data Send track 1. This is normally a Please Wait screen.send track 1 and 3 U25604-J-Z745-1-7600 October 2004 91 . 3 data entry specifies whether track 1 and/or track 3 data is sent to the network.send track 3 only 002 .do not send data 001 . Network response time-out next state number Entry number: 3 Valid range: Description: 000-254.send track 1 only 003 . This timer checks for receipt of a Transaction Reply command message in response to a transaction request.no additional tracks 001 . Send track 2 data Entry number: 4 Valid range: Description: 000-001 This field indicates whether track 2 data should be sent in the transaction request message. 256-999 The state number to which the terminal proceeds if the network does not respond to the transaction request in the time specified by timer 03 (section “Timer Data” on page 167).Configuration Data Screen number Entry number: 2 Valid range: Description: 000-999 States The number of the screen displayed while the terminal transmits a request to the network and waits for the associated Transaction Reply command. 3 Entry number: 5 Valid range: Description: 000-007 The track 1. States Send operation key data Entry number: 6 Valid range: Description: 000-001 Configuration Data This field indicates whether the operation key data should be sent in the transaction request message. The valid values are as follows: 000 .do not send data 001 .send data Send PIN buffer data Entry number: 8 Valid range: Description: 000-001. 128 This field indicates whether the PIN buffer data should be sent in the transaction request message or when bit 128 is enabled use table entry 9 as an extension state definition.send data 128 .use extension state specified in table entry 9 92 October 2004 U25604-J-Z745-1-7600 . The valid bit values are as follows: 000 .send data Send amount buffer data Entry number: 7 Valid range: Description: 000-001 This field indicates whether the amount buffer data should be sent in the transaction request message.do not send data 001 . The valid values are as follows: 000 .do not send data 001 . Configuration Data Send general purpose buffers B and/or C data Entry number: 9 Valid range: Description: 000-003.’V’ reserved The Extension state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as an Extension state table. U25604-J-Z745-1-7600 October 2004 93 . Extension state range: 000-254.send general purpose buffer B data only 002 .do not send data from either buffer 001 .’L’ send optional data fields ’Q’ .’H’ send optional data fields ’I’ . Table 20: Extension state entries Entry 1 2 3 4 5 6-9 Definition state type send general purpose buffers B and/or C send optional date fields ’A’ .send general purpose buffer C data only 003 .send general purpose buffers B and C data Extension to state (I) In the Extension state of the transaction request state additional buffers can be defined to be sent to the network. 256-999 States This field indicates whether the data from the general purpose buffers B and/or C should be sent in the transaction request message. The valid values are as follows: 000 . If bit 128 is enabled in table entry 8 its meaning of this table entry changes to an extension state number definition. the data field is not sent. The valid values are as follows: 000 . If a bit is set.States Send general purpose buffers B and/or C data Entry number: 2 Valid range: Description: 000-003 Configuration Data This field indicates whether the data from the general purpose buffers B and/or C should be sent in the transaction request message.send general purpose buffer C data only 003 .’H’ Entry number: 3 Valid range: Description: 000-255 This entry is bit encoded to control the sending of individual optional data fields in the transaction request message. the corresponding data field is sent.send general purpose buffer B data only 002 .do not send data from either buffer 001 .send general purpose buffers B and C data Optional data fields ’A’ . If a bit is clear. BIT 1 2 3 4 5 6 7 8 Field ID ’A’ reserved ’B’ reserved ’C’ ’D’ ’E’ ’F’ ’G’ ’H’ 94 October 2004 U25604-J-Z745-1-7600 . Configuration Data Optional data fields ’I’ .’V’ Entry number: 5 Valid range: Description: 000-063 This entry is as for entry 3 but with following values: BIT 1 2 3 4 5 6 7 8 Field ID ’Q’ ’R’ ’S’ ’T’ reserved ’U’ ’V’ reserved reserved Field ID ’I’ ’J’ ’K’ ’L’ ’M’ reserved ’N’ reserved ’O’ reserved ’P’ reserved States U25604-J-Z745-1-7600 October 2004 95 .’L’ Entry number: 4 Valid range: Description: 000-015 This entry is as for entry 3 but with following values: BIT 1 2 3 4 5 6 7 8 Optional data fields ’Q’ . 96 October 2004 U25604-J-Z745-1-7600 . if the terminal returns the ID card and the consumer fails to remove the card within the time period specified by timer 02 (section “Timer Data” on page 167). q In addition. the terminal will automatically retain the card. Table 21: Close state entries Entry 1 2 3 4 5 6 7 8-9 Definition state type transaction record form delivered screen number next state number no transaction record form delivered screen number card retained screen number Statement delivered screen reserved not used The Close (J) state entries are defined as follows: State type Entry number: 1 Valid range: Description: J This state ID identifies this state table as a Close state table. returns or retains the activator card as instructed by the Transaction Reply command message.States Configuration Data Close State (J) The Close state should terminate the customer’s current terminal interface. This state performs the following functions: q q displays a screen completes any printing on the customer or journal printer that was initiated by a Transaction Reply command message. Card retained screen number Entry number: 5 Valid range: Description: 000-999 The number of the screen that informs the customer that the card has been retained. U25604-J-Z745-1-7600 October 2004 97 . This screen is displayed upon entry to the close state only if the customer’s card is returned and no transaction record form was printed. No transaction record form delivered screen number Entry number: 4 Valid range: Description: 000-999 The number of the display screen that asks the customer to please take the card. This screen is displayed upon entry to the close state only if the customer’s card has been retained by the terminal as instructed by the network. This screen is displayed upon entry to the close state only if the customer’s card is returned and a transaction record form was printed. Next state number Entry number: 3 Valid range: Description: 000-254. this screen is not displayed. If the customer timesout.Configuration Data Transaction record form delivered screen number Entry number: 2 Valid range: Description: 000-999 States The number of the display screen that asks the customer to please take the card and the transaction record form. 256-999 The state number to which the terminal proceeds after the close state is completed. 000 Entry 7 is reserved and must be 000. This screen is only displayed if the statement is cut and delivered in a close state and the terminal has not been instructed by the last transaction reply message to capture the card Reserved Entry number: 7 Valid range: Description: Not used Entry number: 8-9 Valid range: Description: Entries 8 and 9 are not used by ProCash/NDC or ProConsult/NDC.States Statement delivered screen Entry number: 6 Valid range: Description: 000-999 Configuration Data Display screen to be overlaid when either the receipt is delivered (entry 2) or there is no receipt delivery (entry 4). 98 October 2004 U25604-J-Z745-1-7600 . This state examines the PSTDX entry in the FIT to determine the next state number. state entry 5 contains the next state number. Refer to section ”FIT (Financial Institution Table)” on page 186 for a detailed explanation of the FIT tables. Table 22: FIT Switch state entries Entry 1 2-9 Definition state type next state number The FIT Switch (K) state entries are defined as follows: State type Entry number: 1 Valid range: Description: K This state ID identifies this state table as an FIT Switch state table. U25604-J-Z745-1-7600 October 2004 99 . The next state executed is indexed in this table.Configuration Data States FIT Switch State (K) The FIT Switch state allows the terminal to follow an alternate sequence of states and screens according to the value of the Primary Account Number (PAN) on the activator card. if the FIT identified during the Card Read state contains a PSTDX of 3. For example. Each FIT designates a next state according to the institution type to which it applies. These entries are defined as follows: Entry 2 3 4 5 6 7 8 9 Description next state number if PSTDX = 0 next state number if PSTDX = 1 next state number if PSTDX = 2 next state number if PSTDX = 3 next state number if PSTDX = 4 next state number if PSTDX = 5 next state number if PSTDX = 6 next state number if PSTDX = 7 100 October 2004 U25604-J-Z745-1-7600 . 256-999 Configuration Data Entries 2 through 9 contain the number of the state to which the terminal proceeds depending on the value in the PSTDX value of FIT.States Next state number Entry number: 2-9 Valid range: Description: 000-254. You specify which screen is to be displayed on the screen while writing takes place. Within this command is a field which contains updated track 1/2 or/and track 3 data. If the data are valid and a track write fails the terminal will not attempt any further requested track writes and the write state will exit. the terminal sends a transaction request message to central. You can specify whether or not track 1. One exit is taken if the track write is successful. There are three next state numbers that the terminal can go to once it leaves the Card Write state. This data replaces any previous data in the terminal‘s track data buffer. The following conditions must apply: q If table entry 8 of the Card Read state (Type A) is used. In the transaction request state. a check is made to ensure that the data are valid. Central responds to this message by sending a transaction reply command to the terminal. During the Card Write state the terminal writes the contents of the track 1/2/3 data buffer onto the magnetic stripe of the card. or updated track data from a transaction reply command. A parallel eject/dispense and print (Fast Cash) transaction reply must not have been performed. Another exit taken if the track write is unsuccessful. the order will be first track 1.Configuration Data States Card Write State (L) During a Card Read state the card data buffers are cleared of all previous data. Before writing . The Card Read state defines the card tracks to be read. To use the Card Write state. 2 or/and track 3 data are included in this message. A third exit is taken if the track buffer is empty or contains invalid data and no writing is attempted. q q U25604-J-Z745-1-7600 October 2004 101 . it must not be 000 (return card immediately) A card before cash transaction reply must not have been performed. Writing takes place only if the track data buffer contains data obtained from a successful track 3 read during a card read state. If the terminal is to write more than one track. then track 2 and at least track 3. the magnetic stripe card must still be in the reader. and stores the card track data in the corresponding card data buffer. 256-999 State number goes to after a satisfactory track write operation. Good Write next state Entry number: 3 Valid range: Description: 000-254. 102 October 2004 U25604-J-Z745-1-7600 . Screen number Entry number: 2 Valid range: Description: 010-999 Screen displayed during card write operation.States Table 23: Card Write state entries Configuration Data Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number good write next state bad write next state no write attempted reserved reserved reserved reserved The Card Write state entries are defined as follows: State type Entry number: 1 Valid range: Description: L This state ID identifies this state table as the Card Write state. 256-999 State number goes to if no data or invalid data is present in the track buffer. U25604-J-Z745-1-7600 October 2004 103 . States No Write attempted Entry number: 5 Valid range: Description: 000-254.Configuration Data Bad Write next state Entry number: 4 Valid range: Description: 000-254. This state is also used if a start and/or end sentinel is missing. 256-999 State number goes to if the track write is unsuccessful. Reserved Entry number: 6-9 Valid range: Description: 000 Must be 000 for each table entry. the retry field of the track 3 data buffer must not equal or exceed the limit specified in state table entry 9. the PIN retry field on the card is checked. For ISO format cards. correct PIN next state number local PIN check. next state number local PIN check. After the PIN is entered by the customer and compared with the calculated PIN. the PIN retry field is set to 0. maximum PIN attempts 104 October 2004 U25604-J-Z745-1-7600 .States Configuration Data Enhanced PIN Entry State (M) This state performs the same functions as the PIN Entry (B) state. For a Mutual Institutions Transfer System (MINTS) format card. if the entered PIN is correct. Table 24: Enhanced PIN Entry state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number local PIN check. This check is done before the start of each PIN entry attempt. the PIN retry field is incremented for MINTS format cards and decremented for ISO format cards. If the entered PIN is incorrect. The updated track 3 data buffer is available for transmission through the Transaction Request state.The buffer can also be written on the card using the Card Write state. the PIN retry field in the track 3 data buffer is updated. in both situations the terminal exits to the Maximum Bad PIN’s Next state specified in table entry 6. If that is the case. If an International Standards Organistation (ISO) format card is used. the Cancel Next state exit is taken. Before the customer can enter a PIN for a local PIN check with track 3 retries. the retry field is set to the value specified in state table entry 9. It also supports track 3 retries if the FIT specifies local PIN check and indicates that there is a track 3 retry field on the card. maximum bad PIN’s next state number local PIN check. If the FIT specifies track 3 retries but there is no data in the track 3 buffer. error screen number remote PIN check. the retry field must not equal 0. For MINTS format cards. U25604-J-Z745-1-7600 October 2004 105 . Cancel next state number Entry number: 4 Valid range: Description: 000-254. Entering 255 keeps the terminal in this state until an operation key is pressed.Configuration Data The Enhanced PIN Entry (M) state entries are defined as follows: State type Entry number: 1 Valid range: Description: M States This state ID identifies this state table as an Enhanced PIN Entry state table. Enter 255 to deactivate the time-out function. 256-999 The number of the state to which the terminal proceeds if the customer fails to enter the PIN within the specified time limit. 256-999 This is the number of the state to which the terminal proceeds if the customer presses the cancel key. Screen number Entry number: 2 Valid range: Description: 000-999 This is the number of the screen display that prompts the customer to enter the PIN. This screen is displayed when the terminal enters the PIN entry state. Time-out next state number Entry number: 3 Valid range: Description: 000-254. This screen must position the cursor at the beginning of the area where the Xs are displayed. Local PIN check. Remote PIN check. 256-999 Configuration Data The number of the state to which the terminal proceeds after it verifies that the customer entered the correct PIN (if local PIN check). The number of digits to be checked are specified by FIT field PCKLN. 106 October 2004 U25604-J-Z745-1-7600 . good PIN next state number Entry number: 5 Valid range: Description: 000-254. This state could be a Card Write state in order to update the track 3 PIN retry field. 256-999 The number of the state to which the terminal proceeds if no local PIN check is specified in FIT.States Local PIN check. This screen is displayed each time the customer enters an incorrect PIN until the retry value is reached as specified by state entry 9 (or by the card). Local PIN check. maximum bad PIN’s next state number Entry number: 6 Vollud data range:000-254. This screen must position the screen cursor at the beginning of the area in which the Xs are displayed. next state number Entry number: 8 Valid range: Description: 000-254. error screen number Entry number: 7 Valid range: Description: 000-999 The number of the screen display that prompts the customer to enter the PIN again. 256-999 Description: The number of the state to which the terminal proceeds after the customer incorrectly enters the PIN the number of times specified by state entry 9. Normally the next state is a Pre-Set Operation Code Buffer state. Table 25: Enhanced Amount Entry state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number operation key A next state number operation key B next state number operation key C next state number operation key D next state number extension state number U25604-J-Z745-1-7600 October 2004 107 . The Enter key is equivalent to FDK ‘A’. This entry is used as the PIN retry count if the PIN retry count is not on the card (FIT entry PRCNT = FF). Exit from the Enhanced Amount Entry state occurs when an active FDK is pressed. The Clear key is always active and clears the amount entered and the screen echo field to allow data entry retries within the Amount Entry state. the Cancel key is pressed or a time-out occurs. maximum PIN attempts Entry number: 9 Valid range: Description: 000-009 States This entry specifies the maximum number of times that a customer can enter an incorrect PIN before the terminal goes to the state specified by state entry 6. displays it on the screen. Enhanced Amount Entry State (R) This state reads the amount entered by the cardholder. The Digital Audio Service can echo the keys pressed on the keyboard.Configuration Data Local PIN check. and saves it in the buffers specified by the state table. 256-999 The number of the state to which the terminal proceeds if the consumer fails to enter the amount within the specified time limit. Enter 255 if the time-out function is not required. Operation key A next state number Entry number: 5 Valid range: Description: 000-254. Cancel next state number Entry number: 4 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the A operation key. 256-999 This is the number of the state to which the terminal proceeds if the consumer presses the Cancel key. Value "255" deactivates the A operation key during this state. Screen number Entry number: 2 Valid range: Description: 000-999 This is the number of the screen display that prompts the consumer to enter an amount. Time-out next state number Entry number: 3 Valid range: Description: 000-254.States Configuration Data The Enhanced Amount Entry (R) state entries are defined as follows: State type Entry number: 1 Valid range: Description: R This state ID identifies this state table as an Enhanced Amount Entry state table. 108 October 2004 U25604-J-Z745-1-7600 . Operation key C next state number Entry number: 7 Valid range: Description: 000-254. Normally one operation key is used to indicate whether the amount entry is correct and another is used to indicate whether it is incorrect. U25604-J-Z745-1-7600 October 2004 109 . The other operation keys are inactive.Configuration Data Operation key B next state number Entry number: 6 Valid range: Description: 000-254. 256-999 The state number to which the terminal proceeds if the customer presses the D operation key. 256-999 The state number to which the terminal proceeds if the customer presses the C operation key. 256-999 States The state number to which the terminal proceeds if the customer presses the B operation key. Extension State number Entry number: 9 Valid range: Description: 000-254. Value "255" deactivates the D operation key during this state. Value "255" deactivates the C operation key during this state. Operation key D next state number Entry number: 8 Valid range: Description: 000-254. Value "255" deactivates the B operation key during this state. 256-999 State number of the extension state. Document amount buffer Entry number: 2 Valid range: Description: 000-002 This field determines which buffer the amount entered will be stored in: 000 .General Purpose buffer C 110 October 2004 U25604-J-Z745-1-7600 . Table 26: Extension state entries Entry 1 2 3 4 5-9 Definition state type document amount buffer display amount screen number start CAV command reserved The Extension State entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as the Extension state to the Enhanced Amount Entry state table.Amount Buffer 001 .General Purpose buffer B 002 .States Configuration Data Extension to State (R) This state is the Extension state for the Enhanced Amount Entry state (R). The cursor should be set on the lefthand side of the echo field on the screen.00 (where b = space) Start CAV command Entry number: 4 Valid range: Description: 000-001 This field determines whether to start CAV processing or not if a document is available. ProCash/NDC or ProConsult/NDC only supports value 000. If a non-zero value is downloaded. This is space filled until the required start position for the currency character is reached. U25604-J-Z745-1-7600 October 2004 111 . the cancel next state is taken. Default echo field for eight digits: bbbbb$ 0.Configuration Data Display amount screen number Entry number: 3 Valid range: Description: 000-999 States Overlay screen number that sets the screen cursor position.00 (where b = space) Default echo field for twelve digits: bbbbbbbbb$ 0. This screen optionally defines the initial display format prior consumer amount entry. or an invalid language code. This state is subject to the same restrictions as the language select state. next state language code = 1. next state no. next state language code = 2. You can use this state to automatically select the language to be used from the code on the card. language code = 0. next state language code = 3. next state language code = 5. Table 27: Language Code Switch state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type no language code. next state language code = 4. or to allow manual selection for cards which either have no language code.States Configuration Data Language Code Switch State (S) In this state the flow of a transaction is switched depending on whether a language code is present in the card data or not. See section “Language Select from Card State (V)” for details. next state extension state number 112 October 2004 U25604-J-Z745-1-7600 . Language Code = 0. 256-999 State number the terminal goes to. if the language code is 3. if the language code is 0. next state Entry number: 3 Valid range: Description: 000-254. Language Code = 3. 256-999 State number the terminal goes to. Language Code = 1. 256-999 State number the terminal goes to. U25604-J-Z745-1-7600 October 2004 113 . Entry number: 2 Valid range: Description: 000-254. 256-999 State number the terminal goes to if the language code is illegal or cannot be read. if the language code is 2. Language Code = 2. next state Entry number: 4 Valid range: Description: 000-254. next state Entry number: 5 Valid range: Description: 000-254.Configuration Data The Language Code Switch state entries are defined as follows: State type Entry number: 1 Valid range: Description: S States This state ID identifies this state table as a Language Code Switch state table. No Language Code. next state Entry number: 6 Valid range: Description: 000-254. if the language code is 1. Next State No. 256-999 State number the terminal goes to. A value of 255 means that there is no extension state. next state reserved reserved reserved reserved 114 October 2004 U25604-J-Z745-1-7600 . if the language code is 5. next state language code = 9. Extension to State (S) This state is the Extension state for the Language Code Switch state (S). Extension State number Entry number: 9 Valid range: Description: 000-999 State number of the extension state containing next states for language code 6-9. if the language code is 4. next state language code = 7. 256-999 Configuration Data State number the terminal goes to. and language code 6-9 cause the no language code next state exit to be taken. next state language code = 8. next state Entry number: 8 Valid range: Description: 000-254. 256-999 State number the terminal goes to. Table 28: Extension state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type language code = 6. next state Entry number: 7 Valid range: Description: 000-254. Language Code = 5.States Language Code = 4. 256-999 State number the terminal goes to. Language Code = 7. Language Code = 8. Language Code = 6. next state Entry number: 3 Valid range: Description: 000-254. next state Entry number: 5 Valid range: Description: Reserved Entry number: 6-9 Valid range: Description: 000 Must be 000.Configuration Data States The Extension state entries of the Language Code Switch state are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as the Extension state to the Language Code Switch state. 256-999 State number the terminal goes to. Language Code = 9. 256-999 State number the terminal goes to. if the language code is 7. if the language code is 6. 000-254. next state Entry number: 4 Valid range: Description: 000-254. 256-999 State number the terminal goes to. if the language code is 8. next state Entry number: 2 Valid range: Description: 000-254. U25604-J-Z745-1-7600 October 2004 115 . if the language code is 9. and displays a screen prompting the customer to enter the PIN. This state performs the same functions as the card read state.PIN Entry Initiation State (T) You can use this state instead of the Card Read state (A).PIN Entry Initiation (T) state entries are defined as follows: State type Entry number: 1 Valid range: Description: T This state ID identifies this state table as a Card Read -PIN Entry Initiation state table with a parallel card read. if you want to initiate PIN entry by the consumer at the same time as the terminal reads the card. This state also enables the keyboard for PIN entry while the card is being read. 116 October 2004 U25604-J-Z745-1-7600 .States Configuration Data Card Read .PIN Entry Initiation state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number good read next state number error (misread) screen number read condition 1 read condition 2 read condition 3 reserved extension state number The Card Read . One difference between this state and the Card Read state is that in this state the card is always returned according to the instruction in the Transaction Reply command message. Table 29: Card Read . See also section “Card Read State (A)” on page 59. Configuration Data Screen number Entry number: 2 Valid range: Description: 000-999 States This is the number of the screen display which prompts the customer to insert a card. U25604-J-Z745-1-7600 October 2004 117 . 6 and 7) that tell the terminal which card track(s) must be read. Good read next state number Entry number: 3 Valid range: Description: 000-254. This is the first read condition. Error (misread) screen number Entry number: 4 Valid range: Description: 010-800 This is the number of the screen displayed. Normally. This screen is displayed while the terminal is awaiting card entry. Normally the next state is a PIN entry state type. this screen will prompt the customer to check that the card is inserted correctly and to reinsert the card. This screen will be displayed on the screen. If this condition cannot be met. or if the FIT number on the card matches a FIT number in the FIT table. read condition 2 is used next. Read condition 1 Entry number: 5 Valid range: Description: 001-015 This is one of the three entries (used with entry no. 256-999 The state number the terminal enters after the customer’s card is read properly: Following a good read of the card if FIT’s are not used. Refer to table “Card read state entries” for the definition of the card read conditions. (Table Entry 3 in Extension State = 000). if the card is not read properly. This is the second read condition used. Refer to table “Card read state entries” for the definition of the card read conditions. If neither read condition 1 or read condition 2 can be met.States Read condition 2 Entry number: 6 Valid range: Description: 001-015 Configuration Data This is one of the three entries (used with entry numbers 5 and 7) that tell the terminal which card track(s) must be read. this read condition is used. Read condition 3 Entry number: 7 Valid range: Description: 001-015 This is one of the three entries (used with entry numbers 5 and 6) that tell the terminal which card track(s) must be read. read condition 3 is used. 118 October 2004 U25604-J-Z745-1-7600 . 256-999 State number of the extension state containing information for parallel PIN entry. Card is always returned as specified be the Transaction Replay command message. Card return flag Entry number: 8 Valid range: Description: 000-001 This field is not used. Extension State number Entry number: 9 Valid range: Description: 000-254. This one is used if read condition 1 cannot be done. Refer to table “Card read state entries” for the definition of the card read conditions. The early card eject feature is not supported by this state. If read condition 2 cannot be met. U25604-J-Z745-1-7600 October 2004 119 . The identified screen must leave the screen cursor positioned at the beginning of the PIN entry display area. This screen is displayed on card entry. Screen number Entry number: 2 Valid range: Description: 010-999 Display screen that prompts cardholder to enter PIN. must be 000 reserved. An X is displayed for each key pressed. track 1 name cannot be displayed at this time as card has not been read. must be 000 reserved. Table 30: Extension state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number no fit match next state number clear key mask (not supported) accept key mask (not supported) reserved. must be 000 reserved.Configuration Data States Extension to State (T) This state is the Extension state to the card read state (T). must be 000 The card read extension state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as the extension state to the card read state (T). States No FIT match Next state number Entry number: 3 Valid range: Description: 000-254. 256-999 Configuration Data State number terminal goes to if the financial institution number on the card does not match any FIT. Language Select From Card State (V) In this state you can set one of state tables to display screens in different languages within the same transaction. and you specify which language is to be used in each group. This code is located using the Language Code Index parameter (PLNDX) in the FIT. This is determined by one character (byte) on the cardholder’s card. See chapter “Security Features” for more details. Table 31: Language Select From Card state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type next state number language code for group 1 language code for group 2 language code for group 3 language code for group 4 language code for group 5 language code for group 6 screen group size (range 000-400) 120 October 2004 U25604-J-Z745-1-7600 . You can use up to six screen groups in this state. If FIT’s are not used this entry must be 000. You also specify in table entry 9 how many screens each group will contain. Language Code Entry number: 3 Valid range: Description: 0-9 Decimal number in range 0-9 identifying code for screen group 1. Language Code Entry number: 5 Valid range: Description: 0-9 Decimal number in range 0-9 identifying code for screen group 3. Language Code Entry number: 4 Valid range: Description: 0-9 Decimal number in range 0-9 identifying code for screen group 2.Configuration Data States The Language Select From Card (V) state entries are defined as follows: State type Entry number: 1 Valid range: Description: V This state ID identifies this state table as a Language Select From Card state table. U25604-J-Z745-1-7600 October 2004 121 . Next state number Entry number: 2 Valid range: Description: 0-9 State number terminal goes to after selecting the screen group. States Language Code Entry number: 6 Valid range: Description: 0-9 Configuration Data Decimal number in range 0-9 identifying code for screen group 4. Language Code Entry number: 7 Valid range: Description: 0-9 Decimal number in range 0-9 identifying code for screen group 5. Screen Group Size Entry number: 9 Valid range: Description: 000-400 State number of the extension state containing information for parallel PIN entry. 122 October 2004 U25604-J-Z745-1-7600 . Code Entry number: 8 Valid range: Description: 0-9 Decimal number in range 0-9 identifying code for screen group 6. FDK I next state no.Configuration Data States FDK Switch State (W) Data is placed in the FDK buffer during the FDK Selection state or the FDK Information Entry state. FDK D next state no. FDK B next state no. This data is read by the FDK Switch state in order to identify which next state the terminal should go to. FDK F next state no. FDK C next state no. FDK A Next state No. FDK H next state no. Entry number: 2 Valid range: Description: 000-254. U25604-J-Z745-1-7600 October 2004 123 . Table 32: FDK Switch state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type FDK A next state no. The FDK Switch (W) state entries are defined as follows: State type Entry number: 1 Valid range: Description: W This state ID identifies this state table as a FDK Switch state table. 256-999 State number terminal goes to depending on key code stored in FDK buffer. FDK G next state no. 256-999 State number terminal goes to depending on key code stored in FDK buffer. FDK G Next state No. Entry number: 7 Valid range: Description: 000-254.States FDK B Next state No. Entry number: 6 Valid range: Description: 000-254. 256-999 State number terminal goes to depending on key code stored in FDK buffer. FDK F Next state No. 256-999 State number terminal goes to depending on key code stored in FDK buffer. 124 October 2004 U25604-J-Z745-1-7600 . 256-999 Configuration Data State number terminal goes to depending on key code stored in FDK buffer. 256-999 State number terminal goes to depending on key code stored in FDK buffer. Entry number: 3 Valid range: Description: 000-254. Entry number: 4 Valid range: Description: 000-254. FDK C Next state No. FDK D Next state No. Entry number: 5 Valid range: Description: 000-254. FDK I Next state No. Entry number: 9 Valid range: Description: 000-254. U25604-J-Z745-1-7600 October 2004 125 . 256-999 States State number terminal goes to depending on key code stored in FDK buffer.Configuration Data FDK H Next state No. Entry number: 8 Valid range: Description: 000-254. 256-999 State number terminal goes to depending on key code stored in FDK buffer. 126 October 2004 U25604-J-Z745-1-7600 . You can use this function. where a screen offers a selection of fixed amounts that the cardholder can select by pressing a particular FDK. Table 33: FDK Information Entry state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number.States Configuration Data FDK Information Entry State (X) When the cardholder selects an FDK. The FDK key code is stored in the FDK buffer for use by an FDK Switch state. for example. This state translates the FDK selected by the cardholder into a value that is placed in the specified buffer. cancel next state number FDK next state number extension state number buffer ID FDK’s active mask reserved The FDK Information Entry (X) state entries are defined as follows: State type Entry number: 1 Valid range: Description: X This state ID identifies this state table as the FDK Information Entry state. this state places the corresponding value in the general purpose buffer or amount buffer that you have specified in table entry 7. Table entries 2-9 in the extension to this state contain values relating to the FDK’s. FDK Next state Entry number: 5 Valid range: Description: 000-254. Cancel Next state number Entry number: 4 Valid range: Description: 000-254. Extension State Number Entry number: 6 Valid range: Description: 000-254. 256-999 State number the terminal goes to if the cancel key is pressed. Enter 255 if the time-out function is not required.Configuration Data Screen number Entry number: 2 Valid range: Description: 010-999 States Display screen that prompts key selection by the consumer. U25604-J-Z745-1-7600 October 2004 127 . Time-out Next state number Entry number: 3 Valid range: Description: 000-254. 256-999 State number the terminal goes to if an FDK is pressed. 256-999 State number of the extension state containing assigned values for the 8 FDK’s. 256-999 State number the terminal goes to if the consumer fails to respond to the message on screen within the permitted time limit. 128 October 2004 U25604-J-Z745-1-7600 . If a bit is ‘0’ the relative FDK is inactive.specifies the number of zeros in the range 0-9. The eight bits the binary equivalent of an FDK active mask. C. FDK Active Mask Entry number: 8 Valid range: Description: 000-255 Specifies the FDK’s that are active during this state. If Amount buffer is used. If this state is followed by an amount check state the amount entered is assumed to be a whole amount.States Buffer ID Entry number: 7 Valid range: Description: 010-039 Configuration Data Identifies which buffer is to be edited and the number of zeros to add to the values specified in the extension state. Reserved Entry number: 9 Valid range: Description: 000 Must be 000. Each bit relates to an FDK. Bit 0 relates to FDK A. bit 7 relates to FDK I. F and H. D. 01X = general purpose buffer B 02X = general purpose buffer C 03X = amount buffer X . For example in the following mask: b7 0 b6 1 b5 0 b4 1 b3 1 b2 1 b1 0 b0 1 the three decimal characters in table entry 8 are 093 and the active FDK’s are A. the amount buffer will contain 8 or 12 digits. If a bit is ‘1’ the relative FDK is active. depending on the option selected. U25604-J-Z745-1-7600 October 2004 129 . Value stored if FDK A is pressed Entry number: 2 Valid range: Description: 000-999 Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. Table 34: Extension state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type value stored if FDK A is pressed value stored if FDK B is pressed value stored if FDK C is pressed value stored if FDK D is pressed value stored if FDK F is pressed value stored if FDK G is pressed value stored if FDK H is pressed value stored if FDK I is pressed The Extension state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as the Extension state to the FDK Information Entry state.Configuration Data States Extension to State (X) This state is the Extension state to the FDK Information Entry state (X). Value stored if FDK F is pressed Entry number: 6 Valid range: Description: 000-999 Contains a value stored in the buffer specified in the associated FDk Information Entry state (table entry 7) if the specified FDK is pressed. Value stored if FDK C is pressed Entry number: 4 Valid range: Description: 000-999 Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. 130 October 2004 U25604-J-Z745-1-7600 .States Value stored if FDK B is pressed Entry number: 3 Valid range: Description: 000-999 Configuration Data Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. Value stored if FDK G is pressed Entry number: 7 Valid range: Description: 000-999 Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. Value stored if FDK D is pressed Entry number: 5 Valid range: Description: 000-999 Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. Configuration Data Value stored if FDK H is pressed Entry number: 8 Valid range: Description: 000-999 States Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. U25604-J-Z745-1-7600 October 2004 131 . Value stored if FDK I is pressed Entry number: 9 Valid range: Description: 000-999 Contains a value stored in the buffer specified in the associated FDK Information Entry state (table entry 7) if the specified FDK is pressed. the key code of the FDK selected by the cardholder is stored directly in the operation code buffer. which are then stored in the operation code buffer. then multi-language is not used. If you do specify an extension state. If you do not specify this extension state. and updates the operation code buffer. stores the key code in an FDK buffer for use by an FDK switch state. If you do not specify an extension state in table entry 6. 132 October 2004 U25604-J-Z745-1-7600 .States Configuration Data Eight FDK Selection State (Y) This state reads the FDK selected by the cardholder. You can specify a second extension state in table entry 9 to identify the screen bases for multi-language screen displays. the key code is translated into three pseudo key codes. Table 35: Eight FDK Selection state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen number time-out next state number cancel next state number FDK next state number extension state number buffer positions FDK’s active mask multi language extension state number The Eight FDK Selection state (Y) state entries are defined as follows: State type Entry number: 1 Valid range: Description: Y The state type entry identifies this state table as the Eight FDK Selection state table. 256-999 State number the terminal goes to if the cardholder does not respond to the message on screen within the specified time limit. 256-999 State number the terminal goes to if the cardholder presses the cancel key.Configuration Data Screen number Entry number: 2 Valid range: Description: 000-999 States Display screen which prompts key selection by the cardholder. Extension state number Entry number: 6 Valid range: Description: 000-254. FDK next state number Entry number: 5 Valid range: Description: 000-254. 256-999 State number of extension state containing assigned operation codes for the 8 FDK’s. 256-999 State number the terminal goes to if the cardholder presses an FDK. Cancel next state number Entry number: 4 Valid range: Description: 000-254. Enter 255 if the time-out function is not required. Time-out next state number Entry number: 3 Valid range: Description: 000-254. If there is no extension state enter 255. U25604-J-Z745-1-7600 October 2004 133 . this contains the extension state number. If a bit is 1 the relative FDK is active. enter 000 or 255. Bit 0 relates to FDK A. 134 October 2004 U25604-J-Z745-1-7600 . each in the range ‘0’ to ‘7’. If a bit is 0 the relative FDK is inactive. B. bit 7 relates to FDK I. C. 256-999 If the state selects the multi language screen base. These three values must be ordered to correspond with the edit characters in the extension state. FDK’s active Mask Entry number: 8 Valid range: Description: 000-255 Specifies the FDK’s that are active during this state. G. this is specified in the extension state. are specified to define three positions in the 8 byte operation code buffer to be edited. BIT mask: b7 b6 1 0 b5 1 b4 1 b3 0 b2 1 b1 1 b0 1 Multi language Extension state number Entry number: 9 Valid range: Description: 000-254. Three numeric values. F. If there is no extension state. Each bit relates to an FDK. the three decimal characters in the table entry are 183 and the active FDK`s are A. extension state: This specifies three bytes of the operation code buffer to be set to the values specified in the extension state. and I.States Buffer positions Entry number: 7 Valid range: Description: 000-777 Configuration Data no extension state: This defines the operation code buffer position to be edited by a value in the range ‘000’ to ‘007’. If no buffer positions or less than three buffer positions are to be edited. The eight bits represent the binary equivalent of an FDK active mask. For example in the following mask. Configuration Data States Extension to State (Y) This state is the Extension state to the Eight FDK Selection state (Y). Table 36: Extension state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type operation code stored if FDK A pressed operation code stored if FDK B pressed operation code stored if FDK C pressed operation code stored if FDK D pressed operation code stored if FDK F pressed operation code stored if FDK G pressed operation code stored if FDK H pressed operation code stored if FDK I pressed The Extension state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z Identifies this state table as the Extension state for the Eight FDK Selection state table. U25604-J-Z745-1-7600 October 2004 135 . Table 37: Extension state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type screen language offset if FDK A is pressed screen language offset if FDK B is pressed screen language offset if FDK C is pressed screen language offset if FDK D is pressed screen language offset if FDK F is pressed screen language offset if FDK G is pressed screen language offset if FDK H is pressed screen language offset if FDK I is pressed 136 October 2004 U25604-J-Z745-1-7600 .‘I’.States Operation Code stored if FDK pressed Entry number: 2-9 Valid range: Description: ‘A’ .‘I’. The values 1 to 9 and 0 represent the characters ’A’ . 0 Configuration Data This table entry contains the operation code characters to be written to the operation code buffer if the specified FDK is pressed.‘I’. They are written in order to the three positions specified in the Eight FDK Selection state table (entry 7). Multi Language Extension to State (Y) This state is the Multi Language Extension state to the Eight FDK Selection state (Y).9. Enter ‘@’ if no character is to be written to a specified position in the buffer (fields are unchanged). Three characters are specified for each code. which must be in the range ‘A’ . ’@’ or 1 . and ’@’. and all unused fields should contain this value. U25604-J-Z745-1-7600 October 2004 137 .Configuration Data The Multi Language Extension state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z States Identifies this state table as the Multi Language Extension state for the Eight FDK Selection state table. Screen language offset if FDK pressed Entry number: 2-9 Valid range: Description: 000-999 Each table entry contains the screen number of the first screen for each language group. The initial offset is 000. States Configuration Data Audio Control State (i) The Audio Control State allows the consumer to set the volume for the voice message that will be played for the duration of the current transaction. The message is not played if the option is not offered. The state table sets which audio channels are in use on entry to this state. then a message prompting the cardholder to adjust the volume is played repeatedly. If you map the FDKs to the numeric keyboard. If the cardholder is to be given the option. The volume returns to its default level on exit from the Close State. you can map FDKs to the PIN pad and play an appropriate message. The Audio Control State's prompt screen must not contain an audio message. The cardholder may press: q FDKs to increase or decrease the volume This functionality can be disabled by setting entry 7 in the state table. The state takes the Function Complete Next State exit CANCEL to return the volume to its default level. See Table 38 on the following page for state table entry definitions: 138 October 2004 U25604-J-Z745-1-7600 . the left the two channels (left and right channel) can be connected to a loudspeaker and the right channel can be connected to a headphone jack (if physically installed). For example. q q If the cardholder does not press any keys within the time specified by Timer 00. the cardholder can adjust the volume by pressing numeric keys instead of the FDKs ENTER to set the volume at its current level. then this state invokes the Time Out State. Make sure that the screen associated with the Time Out State is helpful to cardholders with visual difficulties. The state takes the Function Complete Next State exit. and whether the cardholder will be given the option to adjust the volume. If the terminal has a sound card installed. Furthermore the consumer can switch between the audio channels of the sound card. Timeout next state Entry number: 3 Valid range: Description: 000-254.Configuration Data Table 38: Audio Control state entries States Entry 1 2 3 4 5 6 7 8 9 Definition state type Prompt screen Timeout next state Function complete next state Increase Volume FDK mask Decrease Volume FDK mask Audio control Audio message Reserved The Audio Control (‘i’) state entries are defined as follows: State type Entry number: 1 Valid range: Description: ’i’ This state ID identifies this state table as an Audio Control state. This screen is only displayed if table entry 7 indicates that the volume is to be adjusted. Prompt screen Entry number: 2 Valid range: Description: 000-999 Prompts user to adjust volume. U25604-J-Z745-1-7600 October 2004 139 . Value 255 disables the time-out feature. 256-999 State number to which the terminal proceeds if the cardholder has responded within the time specified by Timer 00. bit 1 to FDK B etc. A value of 000 disables this entry and is discouraged.there is no audio file present on the terminal Increase Volume FDK mask Entry number: 5 Valid range: Description: 000-255 Specifies which FDKs will increase the volume in this state. 140 October 2004 U25604-J-Z745-1-7600 . 256-999 Configuration Data State number to which the terminal proceeds if: . Bit 0 relates to FDK A. Decrease Volume FDK mask Entry number: 6 Valid range: Description: 000-255 Specifies which FDKs will decrease the volume in this state. The FDKs are not enabled unless the least significant bit of table entry 7 is 1.table entry 7 selects a channel but disables volume adjustment . Decrease Volume takes precedence.the cardholder selects Cancel or Enter . If a bit is 1 then the FDK referred to is active. The FDKs are not enabled unless the least significant bit of table entry 7 is 1. bit 1 to FDK B etc. Bit 0 relates to FDK A. otherwise it is inactive. A value of ”000” disables this entry and is discouraged.States Function complete next state Entry number: 4 Valid range: Description: 000-254. Where the same FDK is specified as having both Increase Volume and Decrease Volume functions. If a bit is 1 then the FDK referred to is active. otherwise it is inactive. If this entry does not instruct a change to the audio channel in use. the current audio channel(s) will remain in use.enables loudspeaker (left channel) 0 . U25604-J-Z745-1-7600 October 2004 141 .enables audio jack (right channel) States EXAMPLE: For instance. A value of 003 is discouraged in this entry: this would turn both channels off but enable volume adjustment. If there is no audio file present on the terminal. a value of 007 enables volume adjustment and directs audio output to the speaker.enables effect of bits 2 and 3 0 . it will take the Function Complete Next State exit. Provided that table entry 7 indicates that the volume is to be adjusted. Audio message Entry number: 8 Valid range: Description: 000 or 999 Specifies which audio message will be played. the message will be played repeatedly until the state is exited.disables loudspeaker (left channel) 1 .disables audio jack (right channel) 1 .volume adjust off 1 .volume adjust on 0 . 015 enables volume adjustment and enables both channels.disables effect of bits 2 and 3 1 .Configuration Data Audio control Entry number: 7 Valid range: Description: 000-015 This entry is bitmapped: Bit Definition 0 1 2 3 0 . device warning. The general order is: reboot. Also an extension state can be defined which allows additional decisions to jump to a defined next state. i. the priority is top down. The value of the last table entry of the extension state becomes active only if no previous condition was fullfilled. If multiple conditions apply. 142 October 2004 U25604-J-Z745-1-7600 . state ‘h’ entry 3 (reboot) has the highest priority over all values. This state allows to jump into another state flow depending on the actual hardware fitness of the devices defined in the state table. device fatal.States Configuration Data Hardware Fitness State (‘h’) The Hardware Fitness state is a special state designed by Wincor Nixdorf that can be used for specific purposes on Wincor Nixdorf terminals. Table 39: Hardware Fitness state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type no error next state next state if reboot requested (defined in CCERRMAP) next state if CDM fatal error next state if journal fatal error next state if receipt fatal error next state if deposit fatal error reserved for future use extension state number The Hardware Fitness (‘h’) state entries are defined as follows: State type Entry number: 1 Valid range: Description: ‘h’ This state ID identifies this state table as a Hardware Fitness state.e. This reboot request can be issued by errors of classes which have set the reboot flag. This can be used to prevent offering other functions to the customer after serious malfunctions requiring a system reboot have occurred. Next state if Journal fatal error Entry number: 5 Valid range: Description: 000-999 The number of the state to which the terminal proceeds if the journal printer is fatal. U25604-J-Z745-1-7600 October 2004 143 . Next state if Receipt fatal error Entry number: 6 Valid range: Description: 000-999 The number of the state to which the terminal proceeds if the receipt printer is fatal. Next state if reboot requested Entry number: 3 Valid range: Description: 000-999 The number of the state to which the terminal proceeds if a system reboot has been requested.Configuration Data No error next state Entry number: 2 Valid range: Description: 000-999 States The number of the state to which the terminal proceeds if none of the subsequent hardware conditions apply. Next state if Cash Dispenser fatal error Entry number: 4 Valid range: Description: 000-999 The number of the state to which the terminal proceeds if the cash dispenser is fatal. 144 October 2004 U25604-J-Z745-1-7600 . Reserved for future use Entry number: 8 Valid range: Description: 000 or 255 Entry 8 is reserved and must be 000 or 255.States Next state if Deposit fatal error Entry number: 7 Valid range: Description: 000-999 Configuration Data The number of the state to which the terminal proceeds if the deposit module is fatal. Extension state number Entry number: 9 Valid range: Description: 000-999 State number of the extension state (Z) containing additional device conditions. Typically for NDC the Hardware Fitness Extension state is a Z state.Configuration Data States Extension to State (‘h’) The Extension state to the Hardware Fitness state contains additional conditions to go to the specified next state. Table 40: Hardware Fitness Extension state entries Entry 1 2 3 4 5 6 7 8 9 Definition state type denomination type next state if denomination not available next state if journal warning next state if receipt warning next state if deposit warning reserved for future use reserved for future use reserved for future use The Hardware Fitness Extension (Z) state entries are defined as follows: State type Entry number: 1 Valid range: Description: Z This state ID identifies this state table as a Hardware Fitness Extension state. U25604-J-Z745-1-7600 October 2004 145 . Second digit: Specifies the denomination type of cash cassettes which should be verified as out of notes (fatal condition). Next state if Journal warning Entry number: 4 Valid range: Description: 000-999 The number of the state to which the terminal proceeds if the journal printer has a warning status. Next state if Receipt warning Entry number: 5 Valid range: Description: 000-999 The number of the state to which the terminal proceeds if the receipt printer has a warning status. Next state if Denomination not available Entry number: 3 Valid range: Description: 000-999 The number of state to which the terminal proceeds if the Denomination is not available. Third digit: Specifies which cassette position will be checked for low notes (warning condition). The entry range 1-4 indicates denomination Type 1 to 4. The entry range 1-4 indicates the denomination Type 1 to 4. 146 October 2004 U25604-J-Z745-1-7600 . always zero.States Denomination Type Entry number: 2 Valid range: Description: 000-044 The data field is divided in three digits: Configuration Data First digit: Reserved. U25604-J-Z745-1-7600 October 2004 147 .Configuration Data Next state if Deposit warning Entry number: 6 Valid range: Description: 000-999 States The number of the state to which the terminal proceeds if the deposit module has a warning status. Reserved Entry number: 7-9 Valid range: Description: 000 or 255 Entries 6-9 are reserved and must be 000 or 255. 148 October 2004 U25604-J-Z745-1-7600 . The Smart FIT Check state then performs a FIT check on the contents of the three track buffers.States Configuration Data Smart FIT Check State (‘k’) This state is only required when chip data is to be used in a FIT check. This would allow different FIT checks to be performed on data from the same card. It is possible to create more than one Smart FIT Check state to accomodate multiple FIT checks. Table 41: Smart FIT Check State Entry 1 2 3 4 5 6 7 8 9 Definition state type reserved good read next state number error (misread) screen number read Condition 1 read Condition 2 read Condition 3 card return flag no FIT match next state The Smart FIT Check (’k’) state entries are defined as follows: State type Entry number: 1 Valid range: Description: ’k’ This state ID identifies this state table as a Smart FIT Check state. The Smart FIT Check state should be entered after the chip data a read from the smart card and stored in the magnetic track buffers of the application. the card is ejected and this screen is displayed. allowing common FIT check procedures to be used.Configuration Data Reserved Entry number: 2 Valid range: Description: 0 States Not used .set to 0. Bit 0 1 2 3-7 Description Read track 3 Read track 2 Read track 1 Reserved U25604-J-Z745-1-7600 October 2004 149 . Error (misread) screen number Entry number: 4 Valid range: Description: 000-999 If the read conditions are not satisfied due to a bad card or a mechanism error. Good read next state number Entry number: 3 Valid range: Description: 000-999 State number to which the terminal goes if the Financial Institution number on the card matches a Financial Institution number in the FIT. This is left blank to align the following table entries to the same positions as those in the Card Read State. Read condition 1 Entry number: 5 Valid range: Description: see description First of three entries indicating which card track buffer(s) will be read. Bit 0 1 2 3-7 Description Read track 3 Read track 2 Read track 1 Reserved Read condition 3 Entry number: 7 Valid range: Description: see description Third of three entries indicating which card track buffer(s) will be read.eject the card immediately 001 .return the card as specified by a transaction reply message.States Read condition 2 Entry number: 6 Valid range: Description: see description Configuration Data Second of three entries indicating which card track buffer(s) will be read. Description Read track 3 Read track 2 Read track 1 Reserved 150 October 2004 U25604-J-Z745-1-7600 . Bit 0 1 2 3-7 Card return flag Entry number: 8 Valid range: Description: 000-999 Tells the terminal when the card should be returned to the cardholder: 000 . If FITs are not used. It may be a close state or a return to another Chip exit state which places the chip data in the read buffers before calling a different Smart FIT Check state with different read conditions. this entry must be 000.Configuration Data No FIT match next state number Entry number: 9 Valid range: Description: 000 or 999 States This is the state is executed if the FIT check fails. U25604-J-Z745-1-7600 October 2004 151 . States Configuration Data Skip State step The Skip state steps can be used to skip non supported states which can be just ignored through a good next state number definition. Table 42: Skip state step Step name DC_NEXT_1 DC_NEXT_2 DC_NEXT_3 DC_NEXT_4 DC_NEXT_5 DC_NEXT_6 DC_NEXT_7 DC_NEXT_8 Definition uses field 1 for good state next operation uses field 2 for good state next operation uses field 3 for good state next operation uses field 4 for good state next operation uses field 5 for good state next operation uses field 6 for good state next operation uses field 7 for good state next operation uses field 8 for good state next operation 152 October 2004 U25604-J-Z745-1-7600 . new screens can be sent by the network in a Transaction Reply command message. All screens are assigned to a decimal number between 000 and 999.. and so on that can be used for specific functions. Screen Control Characters Nearly in all screens serveral control characters are included. set an overlay screen. Dxx.\LYNXCI\SCREEN”.C06. For detailed descripton see section “Reserved Screens” on page 162. Furthermore the NDC+ protocol is using reserved screen numbers like C00 through C06. The only reserved screens supported. are C00 . Unused screens do not need to be down-line loaded. clear screen.Configuration Data Screens Screens Screen data is also a type of configuration data. A global overview gives Table “Screen control characters” on page 154. the screen number and following data are down-line loaded to the terminal using the Screens Table Load command message. Exx. Axx. etc. Wincor Nixdorf terminals can display screens in the grid of 32 columns by 16 rows. The terminal stores the screen data in the registry location “. Normally. ProCash/NDC and ProConsult/NDC support following major control functions: q q q q q Clears a screen Sets the screen cursor Delays then shows a character Shows inverse video characters Allows blinking U25604-J-Z745-1-7600 October 2004 153 . See section “Screen Design Worksheet” on page 378. However. display Track 1 information. Refer to section “Screen Data Load” on page 242 for details.. like cursor positioning. Restrictively ProCash/NDC and ProConsult/NDC just can store the reserved screens in the registry if they are downloaded from host. data shown on the screen remains unchanged. Each screen data field must be terminated by one of these two screen delimiters. The end of the message terminates the last screen data field in a Screens Table Load command message. overlays the screen specified by the three bytes following SO. FS separates each screen data field in a Screens Table Load command message. and the second byte is the column. to be shown on the customer display. Table 43: Screen control characters cross-reference Control Code CR FF HT SI SO VT ASCII HEX Equivalent 0D 0C 09 0F 0E 0B EBCDIC HEX Equivalent 0D 0C 05 0F 0E 0B Table 44: Screen control characters Control Code CR FF HT Description moves the cursor to the first position in the current row clears the screen and positions the cursor to position @. Normally.Screens Screen delimiters Configuration Data The field separator (FS) or group separator (GS) at the end of the message are screen delimiters. the alternate character is specified by the byte following VT SI SO VT 154 October 2004 U25604-J-Z745-1-7600 . shows an alternate character on the customer display. encoded on track 1 of the customer’s card.@ on the display grid causes the customer’s name. the first byte is the row. screen data can be nested or overlaid to five levels using the control character SO. starting at the current customer display cursor position sets the cursor to the position specified by the two bytes following SI. The terminal displays the name starting at the current cursor position. Screen blinking will be switched off. Any of the 32 columns can be selected by using a column select character ’@’ through ’?’. preceded by a ’VT’ character. ASCII codes in the range 20 . VT control character The VT control sequence is used to display characters from secondary character set. The format of the control sequence is as follows: SI 1A The terminal places the cursor at row 1. See also the grid graphic in section “Screen Design Worksheet” on page 378. The format of the control sequence is as follows: VT C U25604-J-Z745-1-7600 October 2004 155 . forces displaying characters from the Customer Graphic 1 character set. Any of the 16 rows can be selected by using a row select character from ’@’ through 3. column @) of the screen. FF control character The FF control character clears the screen with the default foreground and background colors. HT control character The HT control character inserts the name from track 1 of the customer’s activator card into the screen data. column A.Configuration Data CR control character Screens The CR control character moves the cursor to column @ in the following row.7F hex. SI control character The SI control sequence moves the cursor to a specified row and column. The cursor is set to the top left hand corner (row @. the maximum number of characters per screen is as follows: q q screen 1: 600 characters screens 2 through 6: 310 characters each The network can use an SO control sequence along with an ESC [z control sequence to show animated screens. When using nested screens. In a typical animation sequence. This technique is called nesting. The maximum number of nesting levels is five. The format of the control sequence is as follows: SO nnn The network uses the control character SO to call another screen. the last screen calls the first screen again. Nesting is accomplished by placing control character SO followed by a three-digit screen number within a current screen. 156 October 2004 U25604-J-Z745-1-7600 . To prevent infinite nesting when using animation. the ESC [z control sequence must be the last instruction in each animation screen.Screens SO control character Configuration Data The SO control sequence inserts a specified screen into the current screen. PCXESC\) The backslash character (\) is stored in hexadecimal format (\5c) in the registry.ff. Voice files have to be stored in the path locations defined via parameter AUDIOx_PATH for each language group (x = language group) in section “. path Picture control.\LYNXCI\SCREEN”. (c = font type) ESC P0. (e. Example entry for ESCPE: CONTENTS = “\1bPEC:\5cPICT\5cPICTURE.blinking on (max. ESC\ ESCP199ESC\) ESC P2.67. diplays number nnn picture. Example: kk = 00 . nnn Picture control... ESC ( c Select primary character set. 100 ESC characters per screen) [10. nnn Voice control. diplays a graphic specified via ESC\ path...PCX\1b\5c” U25604-J-Z745-1-7600 October 2004 157 .. Displays the screen in the specified time ttt. ESC\ ESCP2999ESC\) ESC PE.g. ESC is stored as \1b. displays number nn logo. (c = font type) ESC ) c Select secondary character set. nn Logo control. 10 ..g..Configuration Data Table 45: Screen escape sequences cross-reference Screens Escape Sequence ESC P ESC [ ESC ( ESC ) ASCII HEX Equivalent 1B 50 1B 5B 1B 28 1B 29 EBCDIC HEX Equivalent 27 D7 27 63 27 4D 27 5D Table 46: Screen escape sequences Escape Parameters Description Sequence ESC [.. ESCPEC:\PICT\PICTURE.0ESC\ that is played when the screen is displayed.z ttt Display idle sequence. Defines a voice message number ...71m ff = foreground color bb = background color ESC [..m kk.g. (e. (e..blinking off. ESC P1.bb Activates blinking characters and sets foreground and background color. 65535 (16 bit) 256. and one space must separate the text and the icon.Screens Configuration Data Displaying Graphics as Icons ProCash/NDC and ProConsult/NDC can display *. text can share a row with an icon. Non supported graphic extensions. or *. PCX’s. Their combined lengths cannot extend beyond the end of the row.bmp formats. See ProCash/NDC ProConsult/NDC Installation manual section Graphic and Video file extension mapping for detailed descriptions how to map graphic and video files. Additionally the text from the font files can be overlaid (transparent mode) onto full screen graphics. With these graphics it is possible to show animation’s and text together instead of using icons and/or text using WIN-NT font files. one cannot overlap on the other. Also.pcx. Mixtures of all kinds of graphics in one customization image are possible. 65535 (16 bit) 256.bmp files which are smaller than the whole screen as an icon. 65535 (16 bit) PCX graphics are supported in 16 or 256 colors only. if text and the icon share a row. The possibilities are endless. Display resolutions ProCash/NDC and ProConsult/NDC support following display resolutions and color depths: Mode VGA SVGA SVGA SVGA [1] Resolution 640x480 640x480 800x600 1024x768 color depths [1] 16 256. Therefore a cursor positioning is required to fit the icon in the right place. or *. Full Screen graphics Wincor Nixdorf terminals support full screen graphics as *. for example specified in a downloaded screen using the ESCPE control sequence can be mapped to another file extension supported by ProCash/NDC via parameter “PICTURE_EXT_XXX”. You can add text above or below the icon without modifying icon data. 158 October 2004 U25604-J-Z745-1-7600 . BMP’s with/without overlaid text. However.pcx. exe” located in directory “C:\PROTOPAS\BIN” is called that performs function calls to the API of the MCI player.exe”. videos are always played in the foreground window. The only chance to get access to other open windows is via key combination ALT+F4 on the alpha keyboard. Please refer to ProCash/NDC ProConsult/NDC Installation manual to get detailed information how to configure Flash animations in ProCash/NDC and ProConsult/NDC. U25604-J-Z745-1-7600 October 2004 159 . an external program named “ccMciPly. If you get an error or the MCI player doesn’t come up. Some codecs will be installed together with the Internet Explorer or Media Player installation. That means. After you have double clicked the file.mpg or *.exe”.5 or higher to be able to display Flash files. IMPORTANT NOTE: Since version $MOD$ 020701 1009 of “ccMciPly.mpeg. A Flash animation has to be stored as an executable file like “MyFlash. This can be easily tested if you double click the video file. the Microsoft MCI player should come up automatically to play the video. The current version of the Video Compression Codecs can be viewed in the “Multimedia” dialog box in the Control Panel of Windows. The only difference is the file extension. Flash files can be created via different utilities like MacroMedia Flash.Configuration Data Screens Displaying MacroMedia Flash executables ProCash/NDC and ProConsult/NDC are able to display Flash video animations. you have to install the correct Video Compression Codec. ProCash/NDC and ProConsult/NDC are able to display AVI and MPG video files. If you want to play video files it is necessary to check if the video file can be played with the current installed codec on the ATM.exe”. videos are running in the topmost window. Displaying Video files In addition to the graphics. Important Note: You have to install Internet Explorer 5. *. If a video file is specified within the screen flow. Other open windows behind (previously accessed via ALT-TAB) cannot be reached any more. ALT+F4 terminates the program “ccMciPly.avi. which has to be *. They can be configured in the same way as the graphic files. q q Table 47: Default Voice Message files Audio (*. the message starts on entry to the Close state. See also Table 47 for the message description. The terminal attempts to play messages at following times: Auto Voice Feature The following voice messages are spoken if the Auto Voice Feature option 02 is set to 001 in the “Enhanced Configuration Parameters Load” message.WAV 7. the terminal attempts to play pre-recored messages in some states. q PIN Entry (Message 7) The message starts during a PIN Entry state or Enhanced PIN Entry state when the card has been read and recognized. Make sure that the pre-recorded message is brief enough to play completely before the state is timed out. Transaction Request (Message 1) The message starts when a Transaction Request message is sent to the host.WAV Message Number 1 7 8 Message “your transaction is being processed” “please enter your personal identification number” “thank you for using this atm” NOTE: The three WAVE message files are recorded as male voice 160 October 2004 U25604-J-Z745-1-7600 .WAV) file 1. Card Taken (Message 8) The message starts as soon as a card is taken in the Close state.Screens Configuration Data Voice Control If the terminal has installed a sound card and the path of the voice files are configured via AUDIOx_PATH (see ProCash/NDC ProConsult/NDC Installation manual for detailed definition of this parameter). If the card has already been taken.WAV 8. WAV TWO.WAV FIVE.WAV) file ZERO.Configuration Data Audible Echo on Keyboard Screens ProCash/NDC and ProConsult/NDC also support Audio Echo on Keyboard if Option 31 is enabled in the “Enhanced Configuration Parameters Load” message (see Table 48).WAV THREE.WAV FOUR.WAV SIX.WAV Phrase “zero” “one” “two” “three” “four” “five” “six” “seven” “eight” “nine” NOTE: The WAVE files are recorded as female voice U25604-J-Z745-1-7600 October 2004 161 .WAV EIGHT. Table 48 lists the wave files used if Audio Echo on Keyboard is enabled: Table 48: Default WAVE files for Audio Echo on Keyboard Audio (*.WAV SEVEN.WAV ONE.WAV NINE. This screen is displayed when cardholder tampering is suspected and the terminal enters suspend mode. Supply screen. C00 Function More time screen. Temporarily Out of Service screen C01 C02 C03 C04 C05 C06 162 October 2004 U25604-J-Z745-1-7600 . These screens contain default data which is displayed when no reserved screen is downloaded with its own data. Out of Service screen. The screen’s characters default to offline at terminal power up or reset. The screen’s characters default to out-of-service at terminal power-up or reset.Screens Configuration Data Reserved Screens Wincor Nixdorf terminals contain reserved screens C00 through C06 stored in the registry location “. This screen prompts the customer who has failed to respond to a request for keyboard input within the specified keyboard response time. This screen appears on the customer display when the terminal is in out-of-service mode. This screen appears on the customer display when the terminal is offline.\LYNXCI\SCREEN”. Card capture screen. Table 49: Downloaded reserved screens supported by Wincor Nixdorf terminals Screen No. Offline screen. This screen is displayed when the terminal captures a card as a result of a card reader failure Cardholder tampering screen.. This screen is displayed while the terminal is in supervisor mode. the terminal returns to the original state in which the time-out occurred. See ProCash/NDC ProConsult/NDC Installation manual for details.\LYNXCI\SCREEN” the new subsections of your new defined C screens will be created and updated if you start the PARAC run. U25604-J-Z745-1-7600 October 2004 163 .Configuration Data General use of default reserved C screens Screens In addition to Diebold the reserved screens C00-C06 can be downloaded. the terminal returns to the time-out next state entry of the original state in which the time-out occurred. In Registry section ”. q Screen C01 Screen C01 is displayed when the terminal is in offline mode. Normally. The customer presses this key to request more time.PPF’. the following defaults are used: Default screen C00 C01 C02 C03 C04 C05 C06 Downloaded screen 000 001 002 003 none C02 / 002 C02 / 002 If one or more of the reserved screens are not downloaded by the host you can create your own reserved screens in PARAC configuration file ’CUSTOM. If one of those screens is not downloaded. this timeout next state is a close state.. if operation key B is pressed. Screen C00 Screen C00 prompts customers who fail to respond within a specified time interval. Screen C00 must be defined and must conform to the following operation key A and B requirements: q if operation key A is pressed. Screen C04 Screen C04 is displayed when the terminal captures the card in case of a card reader failure. If supply mode is entered from out of service while displaying screen C06. This screen is displayed as long as in the value of Timer 2 specified. This screen is displayed under following conditions: q q When specified in a go out of service comand from host On exit supervisor mode to out of service if supervisor mode was entered from in service and the auto return to previous mode is not set. q 164 October 2004 U25604-J-Z745-1-7600 . When this occurs. This screen is displayed when the terminal is in supervisor mode. See ProCash/NDC ProConsult/NDC Installation manual for details. Screen C05 Screen C05 is displayed when cardholder tampering is suspected and the terminal enters Suspend mode.Screens Screen C02 Configuration Data Screen 002 is displayed when the terminal is in out-of-service mode. the next state is executed. Screen C06 Screen C06 is displayed when the terminal is temporarily in out of service mode. The Suspend mode condition as an error Severity 3 can be configured in CCERRMAP. Screen C03 Screen C03 is the supply screen. Screens normally associated with not in service conditions. should also be in this group if the ’Cxx’ default screens are used. Make sure that all the screens for which a choice of languages can be made are in the group. such out of service.Configuration Data Screens Language Selection You can create multi language customer screens to be displayed as requested from one set of state tables. This can be defined via group definitions for each language. You do not need to cahnge the state tables. The first group must start at ’000’.’000’ – Language B . Note that nested screens must have absolute positions. the screen group bases could be: – Language A . and contain thos screens fro which language selection is not possible. supervisor or offline. EXAMPLE: If four languages are required. or Language Select from Card state.’100’ – Language C . That is. in order to select the language. screens displayed from the Card Read state and Language Select from Card state. in which the equivalent screen for all languages has the same relative position within the group.’300’ If a screen ’055’ is displayed from a state table.’200’ – Language D . but you must include an Eight FDK Selection Function state. the screen is downloaded as: – ’055’ for Language A – ’155’ for Language B – ’255’ for Language C – ’355’ for Language D U25604-J-Z745-1-7600 October 2004 165 . The following sections describe the contents of these data fields. If the key-entry person enters a machine number. Logical Unit Number (LUNO) The second piece of information in the miscellaneous configuration data is called the Logical Unit No. solicited status.Miscellaneous Configuration Data Configuration Data Miscellaneous Configuration Data Miscellaneous configuration data is down-line loaded via (Enhanced) Customisation Table Load command message from network to terminal. (LUNO). The (Enhanced) Customisation Table Load command message has three data fields: q q q terminal parameters logical unit number timer data Each field is preceded by a field separator (FS). and unsolicited status messages (except the power failure unsolicited status message). The LUNO is a unique number that indicates which terminal has transmitted a message. 166 October 2004 U25604-J-Z745-1-7600 . Terminal Parameters The terminal parameters data fields are described in section ”Configuration Parameters Load” on page 245 and section ”Enhanced Configuration Parameters Load” on page 249. Refer to section ”Configuration Parameters Load” on page 245 and to section ”Enhanced Configuration Parameters Load” on page 249 for the message format. the terminal places the terminal number at the end of the LUNO in the transaction request. The timer values are stored in seconds. U25604-J-Z745-1-7600 October 2004 167 .8 second segments (ticks). The time-out intervals are specified as a number of 0. The number of ticks assigned to a timer can be 000 to 255.. Timers are stored in registry location “. specifying a time-out interval of 000 causes the terminal to never take the time-out next state exit from a state. Some timers must be down-line loaded by the network because they do not have default times. This gives each timer a time-out range of 0 to 204 seconds. but they do not have to be as they have default settings.\LYNXCI\TIMER”. Unless otherwise stated in the timer descriptions that follow. Other timers may be down-line loaded. The data for each timer is down-line loaded in the sequence the timer number (2 bytes) then the number of 800-millisecond ticks (3 bytes).Configuration Data Miscellaneous Configuration Data Timer Data The third piece of information in the miscellaneous configuration data is called timer data. and start timer 01. 030 / 038 015 / 019 005 / 006 030 / 038 040 / 050 040 / 050 030 / 038 001 / 001 040 / 050 020 / 025 001 / 001 86 87 94 95 96 97 98 99 018 / 023 (not used) 030 / 038 (not used) 030 / 038 (not used) 030 / 038 000 / 000 010 / 013 (not used) 030 / 038 (not used) 030 / 038 168 October 2004 U25604-J-Z745-1-7600 . display screen number 000. Otherwise.Miscellaneous Configuration Data Table 50: Timer values Configuration Data Timer Default value in PPF Timer Default value in PPF number (seconds / ticks) number (seconds / ticks) 00 01 02 03 04 05 06 07 08 09 10 11 12-14 15 16-17 18 19 20 Timer 00 Timer 00 sets the keyboard response timeout interval. the terminal will exit its present state. When a screen is displayed that prompts the customer to make a keyboard entry. the customer must respond within the timeout interval specified for timer 00. for deposit envelope insertion (timer 04. When the terminal is ready to transmit a Transaction Request message to the network. if the timer expires for the deposit. the customer must respond within the time-out interval specified by timer 04. the terminal starts Timer 03. otherwise. the terminal exits its present state. Timer 05 Timer 05 sets the withdrawal time-out interval for terminals with a withdrawal door. the terminal unlocks the delivery door and starts timer 05. After the cash has been counted and placed in the delivery mechanism. Timer 01 is the timeout interval for the customer’s response to screen 000. 08 or timer 20). The maximum amount of time that the terminal waits for a customer to remove the cash is the sum of timers 05 and 07. If the customer exceeds the timeout interval allowed for keyboard entry (timer 00). screen 000 is displayed. the terminal exits the transaction request state by going to the network response time-out next state number. If the terminal does not receive a Transaction Reply command before Timer 03 expires. If this timer expires for the keyboard. or for securomatic insertion (timer 08).Configuration Data Timer 01 Miscellaneous Configuration Data Timer 01 sets the consumer response extension timeout interval. The keyboard beeper sounds while this timer is active. A timeout interval of 000 is not permitted for timer 02. the terminal advances to timeout next state. the terminal sends a solicited status message to the network. The keyboard beeper sounds while this timer is active. U25604-J-Z745-1-7600 October 2004 169 . Timer 03 Timer 03 sets the communication message timeout interval. When a screen is displayed that prompts the customer to insert an envelope into the depository. the terminal proceeds to the next state number specified in the close state. Timer 02 Timer 02 sets the close state screen time-out interval. displays screen 000 and starts timer 01. Timer 04 Timer 04 sets the envelope insertion time-out interval for the depository. Screen 000 asks if the customer needs more time. At the end of this interval. Timer 08 Timer 08 sets the envelope insertion timeout interval for the night safe depository. this timer starts after timer 10 expires. 170 October 2004 U25604-J-Z745-1-7600 . the terminal proceeds to timer 07. q Timer 06 Timer 06 sets the communications offline timeout interval. If the terminal has not been polled or selected within the interval specified for timer 06. A timeout interval of 000 is not permitted for timer 07. displays screen 000 and starts timer 01. On all terminals without a delivery door.Miscellaneous Configuration Data q Configuration Data If the customer fails to fully open the withdrawal door and clear the rear withdrawal area sensors before timer 05 expires (or to just fully open the door on terminals with a manual door). Timer 07 Timer 07 sets the withdrawal door open timeout interval. On all terminals with a delivery door. the customer has to respond within the timeout interval specified by timer 08. This timer specifies the amount of time that the terminal waits after the withdrawal door is fully opened before going to the next specified state. If the customer fully opens the withdrawal door and clears the rear withdrawal area sensors before timer 05 expires (or just fully opens the door on terminals with a manual door). the terminal exits its present state. This timer is started each time the terminal receives a poll or select sequence from the network. the terminal transmits the withdrawal door solicited status to the network indicating a fault and waits for a new Transaction Reply command message from the network. Otherwise. When a screen is displayed prompting the insertion of a deposit. this timer starts after the withdrawal door is fully opened and either the sensors are cleared or timer 05 expires. A timeout interval of 000 is not permitted for timer 06. the terminal proceeds to offline mode (out-of-service to customers) and displays screen 001. the card is presented to the customer and not removed within this time period. and activates the beeper. a card capture attempt is made. A timeout interval of 000 is not permitted for timer 09. Timer 11 sets the amount of time the vandal shield delays before it begins to close. the total amount of time that the terminal waits for a customer to remove the cash is the sum of timers 10 and 07. A value of 000 in timer 10 will result in no beeping and zero time. Timer 10 Timer 10 sets the withdrawal timeout interval for terminals without a withdrawal door. The default setting for timer 09 on power-up is 30 seconds (38 ticks). The vandal shield uses this timer if a value of 004 is in state entry 3 of the vandal shield state. timer 09 stops. Timer 11 (CSC450 with vandal shield only) Timer 11 sets the vandal shield delay time before closing. This timer starts after the terminal executes the card return function ID and at the beginning of the close state if the card was not returned at the card read state. After the terminal counts and places the cash in the withdrawal area. Therefore. the terminal displays a Take Cash screen. The default setting for timer 10 on power-up is 006 ticks. Timers 02 and 09 start at the same time. After timer 10 expires.Configuration Data Timer 09 Miscellaneous Configuration Data Timer 09 sets the customer timeout interval before a card capture attempt. If. U25604-J-Z745-1-7600 October 2004 171 . the terminal stops the beeper and starts timer 07. When the card is removed. Timer 11 defaults to 080 ticks on power-up. starts timer 10. during a close state. Timer 10 sets the amount of time the beeper beeps while waiting for the customer to take the cash. When the timer expires. Timer 20 Timer 20 sets the insertion timeout interval for the depository. Timer value zero means no wait. It determines when to retract a statement that has not been taken by the customer.Miscellaneous Configuration Data Timer 15 Configuration Data Timer 15 is used with the card read ‘T’ state (not used by Wincor Nixdorf terminals). Timer 20 allows seven seconds of silent time. This timer is used during the Close State processing. Timer 96 Timer 96 sets the statement present timeout. Timer 18 Timer 18 sets the swipe card reader error screen timer (not used by ProCash/NDC and ProConsult/NDC application). This timer is also used when Transaction Reply command ’S’ is sent in the transaction reply and the statement is laying in the collection tray of the statement printer. If timer 20 is configured to a non-zero value. The timer will be started when this condition is detected. The default value is 30 ticks and the timer is not used if you set a zero value. Transaction Reply command ’S’ commences without retract attempt. If the statement is taken before the timer expires. it is used instead of timer 04. Timer 95 Timer 95 sets the statement retract timeout. the next state specified by the transaction reply command is entered. Timer 99 Timer 99 specifies after what time the vandal guard close operation should be started when the consumer transaction has been finished. after which the beeper starts at a slow rate for the remainder of the specified time. 172 October 2004 U25604-J-Z745-1-7600 . This timer is used only in the statement and continue function and is started regardless of whether or not a statement has been delivered. If the timer expires the statement is retracted and Transaction Reply command ’S’ commences. cmd: regedit -s stt010. The following table describes the filenames. Depending on the existing file name the local download is called after the ATM has received the Config ID and/or a Go in Service command. U25604-J-Z745-1-7600 October 2004 173 .reg.cmd dcInServ. graphic file locations or printer settings).cmd or dcInServ. Note: The command job must return within 30 seconds. location and in which situations the files are called: Filename dcCfgId.reg could contain following entries: REGEDIT4 [HKEY_LOCAL_MACHINE\SOFTWARE\Wincor Nixdorf\ProTopas\CurrentVersion\LYNXCI\STATE\010] "STEP_PARAM"="113217217013211012013003" overloads values of state 010. Configure local download Local download procedures can be called after following two situations: q q ATM has received Config ID (Set Config ID command) from host ATM has received Go in Service command from host The local download process can be evaluated via two batch files. Contents of dcCfgId.g.reg Description: Calls regedit silent (no screen appears) to update contents of stt010. With local downloads you can skip unsupported functions or overwrite non legal values in states or screens and it allows to enhance the host configuration with new functions locally. In addition to the download modifications you can also change local ATM settings (e. The contents of stt010.cmd Directory C:\PROTOPAS\CONF C:\PROTOPAS\CONF Called when after Config ID received after Go in Service received The contents of the files can be any command which is supported in a Windows command line window.Configuration Data Local download feature Local download feature The local download feature is useful if you want to overload the downloaded customization image (CI) from host with local defined settings. Local download feature Configuration Data 174 October 2004 U25604-J-Z745-1-7600 . Algorithm An algorithm is a structured mathematical procedure for solving a specific problem. U25604-J-Z745-1-7600 October 2004 175 . which are defined below. the customer is identified and can access the relevant accounts. Data Encryption Standard [DES] Encryption keys Personal Identification Number [PIN] PIN verification PIN verification is the method of ensuring that the PIN entered on the ATM is the proper PIN for the card inserted in the ATM.Security Features General Overview To understand and use the information in this section. The DES algorithm is not confidential and can be obtained by the general public. The keys used as part of the algorithm are what provides the confidentially The Data Encryption Standard (DES) specifies an algorithm to be used in electronic hardware devices for the purpose of cryptographic protection of computer data. The DES algorithm is designed to encrypt and decrypt blocks of data. you should understand some basic terms and concepts. the keys must be kept secret to ensure the confidentiality of the data being encrypted. As the DES algorithm is available to the general public. The Personal Identification Number (PIN) is the customer’s way of verifying his or her identity as established by an activator card. Encryption keys are numbers that are used as part of the PIN verification process and also for encrypting messages to and from the terminals. By entering this PIN. which is sent to the network – control of the transaction sequence of the terminal via FIT switch indexes. This section describes both the PIN and the processes required to verify the PIN. This is done by supplying state flow through the FIT.PIN and PIN Verification Security Features Financial Institution Table [FIT] The Financial Institution Table (FIT) provides the following items to the network: – capacity of using multiple card formats and multiple institutions – the type of PIN verification – the encryption key (if PEKEY is used) that is used to encrypt a PIN. a request for PIN entry is made after the customer has inserted an activator card into the terminal. The terminal and/or the network must then verify the PIN before the transaction can continue. Typically. The processes for this verification are called PIN verification processes. 176 October 2004 U25604-J-Z745-1-7600 . FIT can also be used to allow the institutions to define the exact operation flow of the terminal. the customer must enter a Personal Identification Number (PIN). PIN and PIN Verification In order to access a Wincor Nixdorf customer service terminal. Message Authentication Code [MAC] Message Authentication Code (MAC) provides a method of ensuring that messages sent between the terminal and the network are authentic and have not been modified. but any given PAN has only one possible PIN. Generally. then awaits the go-ahead before giving a transaction selection to the customer. This is done through a PIN entry state. one of two transaction request messages is usually sent to the network. PIN Entry The first step in the PIN verification process is the customer’s PIN entry. When remote PIN verification is used instead of local PIN verification. A particular key and a set of PAN’s correspond to a set of PIN’s. one PIN may be derived from several PAN’s. In the second way. Usually. Some of the PIN’s may be duplicated. the network can authorize or deny either the PIN or transaction. the process that generates the customer’s PIN also verifies that PIN. it is possible to use only those PAN digits that vary from customer to customer. The terminal then sends both the unverified PIN and the transaction request to the network in the same message. U25604-J-Z745-1-7600 October 2004 177 . In the first method. The examples and explanations in this document assume that the PAN is the account number associated with the PIN. The second request message holds the current transaction information. It is not necessary to use the entire PAN. In most PIN verification methods that account number is the Primary Account Number (PAN). some type of key governs the algorithm sequence. Then. the terminal can accept any PIN and continue with a transaction selection to the customer. a sequence of mathematical steps. the terminal forwards the PIN to the network in one request message. the terminal verifies the PIN and goes to the next state required. that is. If local PIN verification is being used.Security Features Personal Identification Number (PIN) Personal Identification Number (PIN) The PIN is generally derived from an account number. The local PIN verification process is based on an algorithm. however. In modulo 10. the maximum number of PIN digits may be nine. but modulo 10. As soon as the customer enters the maximum number of PIN digits. the terminal automatically completes the PIN entry state. For example. On entry of the ninth digit. To accomplish this. the customer must press operation key A after the five-digit PIN is entered. an offset is added to or subtracted from the customer’s generated PIN to obtain the desired PIN. For example. After the customer presses operation key A. if the maximum PIN length is nine digits and the customer has a fivedigit PIN. Customers receiving shorter PIN’s must press operation key A (which is active on PIN entry) to signal the end of the entry. The institution may issue PIN’s shorter than the maximum PIN length defined in a FIT. the terminal automatically completes the PIN entry state. The PIN verification will fail and a retry or error state occurs (depending on the configuration of the states). The following example shows the difference between these two mathematical systems. This is not. no figures are carried. The FIT field PMXPN indicates the maximum number of PIN digits that a customer may enter.Personal Identification Number (PIN) Security Features Variable length PIN Entry Using FIT. the PIN offset number allows an institution to let customers choose any PIN they wish. If the customer inadvertently presses operation key A before entering all of the required PIN digits. 178 October 2004 U25604-J-Z745-1-7600 . the terminal automatically completes the PIN entry state. ordinary addition or subtraction. 2716 + 3329 5035 (modulo 10) Note: 2716 + 3329 6045 (regular addition) Diebold PIN and VISA/ABA PIN verification is not supported by ProCash/NDC and ProConsult/NDC. PIN Offset Number (DES verification) For DES PIN verification. the terminal can accept a variable-length PIN. the terminal automatically attempts to verify the digits entered. If an institution does not wish to use the offset. the CPIN would be calculated as follows: 5646 + 1507 6143 GPIN OFFSET CPIN An activator card data track stores the offset. The type of terminal you have and the data security equipment installed may dictate the processes that are available to you. it may be set to zero. FIT entry POFDX tells the terminal where to find the offset on the activator card data track.Security Features Personal Identification Number (PIN) In the DES PIN verification process. For example. For Wincor Nixdorf cash terminals. the offset is added to the generated PIN to obtain the customer PIN. if the GPIN is 5646 and the offset is 1507. the following equipment is available to control PIN handling: q q DES PIN algorithm Encryption Decryption Module (EDM) U25604-J-Z745-1-7600 October 2004 179 . PIN Verification Processes ProCash/NDC and ProConsult/NDC support following types of PIN verification: q q DES local DES remote These PIN verification processes are the steps that either the terminal or the network performs to verify that a customer-entered PIN is valid. Depending on the FIT entries the terminal determine if the PIN should be checked locally or remote by the host. The following sections describe some of the essentials for PIN verification and each verification process. This feature also encrypts the PIN before sending it to the network. The EDM encrypts the PIN before sending it to the network for verification.PIN Verification Security Features The following paragraphs describe this equipment and list the PIN verification processes that the equipment supports. This type of encryption provides increased security for the PIN. These FIT entries tell the terminal what PIN verification process to use and where to find the information that the terminal needs to perform the verification process. PIN Verification Wincor Nixdorf terminals support local or remote PIN verification. DES PIN DES PIN encryption provides for local DES PIN verification and remote network PIN verification. The Encryption Decryption Module (EDM) (available in all cash out systems) provides all the features of the DES PIN Verification/ Encryption option and the following additional features: q q EDM Message Authentication (MAC) PIN encryption using Diebold or ANSI format DES PIN requires Financial Institution Table (FIT) entries. Remote PIN Verification The terminal can also send the PIN to the network for verification rather than verifying the PIN at the terminal. 180 October 2004 U25604-J-Z745-1-7600 . Network PIN Verification Network PIN verification requires that the PIN be padded to 16 digits and encrypted before sending it to the Network. Decimalization ensures that the PIN digits are decimal. This can be done by comparing the encrypted PIN to a table of encrypted PIN values. This algorithm is a standard procedure available to the public. In the second procedure. The network then handles the PIN verification. The encrypted PAN is decimalized using the decimalization table in the FIT. This PIN key is stored at the terminal. The PIN key serves the same purpose as the ALGO. the PIN key is encrypted using the DES algorithm and another secret key. then send it to the Network with unencrypted PAN and offset. The PIN key governs a sequence of operations in the DES ALGO. The terminal can encrypt the customer-entered PIN once or twice. the decrypted PEKEY is the PIN key that is used to encrypt the PAN. If the PIN is correct the transaction can be continued. For remote PIN verification. When the encrypted PIN reaches the verification point in the network. the key is the PIN key. To obtain greater security. The institution may choose to verify the encrypted PIN without performing decryption. the PIN is sent to the network in two different forms: q q q ANSI PIN/PAN Block Diebold PIN Block BANKSYS PIN Block The terminal encrypts the block and sends it to the network. The FIT field PMXPN tells the terminal which form to use. Then the generated PIN will be compared with the calculated PIN. but this is not recommended only for system testing. See section ”Maximum PIN Entry Digits (PMXPN)” on page 191 for more details on PMXPN. During PIN verification. Therefore the PAN is used as a table look-up key. U25604-J-Z745-1-7600 October 2004 181 . Security is achieved by keeping the PIN key confidential. The PIN may be send unencrypted. Before adding the generated PIN to the offset.Security Features PIN Verification Local PIN Verification In the DES PIN verification process. the terminal (or network) decrypts PEKEY to restore the PIN key. The first procedure decrypts PEKEY from the FIT using the Master key. DES PIN verification must go through two algorithm procedures. a single (or double) decryption restores the customer entered PIN. The resulting encrypted PIN key (PEKEY) is put into a FIT entry. The PIN block and PAN block are then exclusively ORed together to create the PIN/PAN block. The number of digits is determined by the FIT parameters PANLN. hex 0’s are used to fill the remaining slots. PANDX. If the PAN digits are less than 12. The PAN digits are the least significant digits of the PAN. This block is then encrypted according to the FIT field PINPD and sent to the network. and PINDX. The ANSI PIN block is 16 hex digits and appears as follows: PIN digits PIN digits or hex F depending on length of PIN Filled with hex digit F Length of PIN (4-12) Control field (presently 0) The PAN block is 16 hex digits and appears as follows: PAD digits PAN digits The PAD digits are always hex 0. 182 October 2004 U25604-J-Z745-1-7600 .PIN Verification ANSI PIN/PAN Block Security Features The ANSI PIN/PAN block is a 16-hex digit block that contains the result of exclusively ORing the ANSI PIN block and the Primary Account Number (PAN) block. Security Features Diebold PIN Block PIN Verification The Diebold PIN block is 16 hex digits and appears as follows: PIN digits PIN or PAD digits depending on PIN length PAD digits Refer to section ”PIN Pad Character (PINPD)” on page 194 for more details on the Diebold PIN block. the 16 ASCII digits are converted prior to transmission. The host must reconvert the received 16 digits to 16 hex digits prior to decrypting PIN buffer A. each digit must be converted by using the conversion prior to combining the digits into eight bytes. If the host protocol is EBCDIC. HEX DIGIT 0 1 2 3 4 5 6 7 8 9 A B C D E F ASCII (HEX) 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F GRAPHIC DIGIT 0 1 2 3 4 5 6 7 8 9 : . These 16 ASCII digits are sent to the host if the protocol is ASCII. The Diebold implementation of DES uses 16 hex digits. If the protocol is ASCII. 0-F. the only conversion required is removing the prefixed hex 3 from each digit and combining the resultant into eight bytes. The encryption process results in 16 hex digits that are converted to ASCII by prefixing each hex digit with a hex 3 to convert the 16 hex digits to 16 ASCII digits. If the communication protocol is EBCDIC. The following table shows the conversion from ASCII to EBCDIC. < = > ? EBCDIC (HEX) F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 7A 5E 4C 7E 6E 6F U25604-J-Z745-1-7600 October 2004 183 . the 16 hex digits internal to the terminal before encryption are: 45 12 FF FF FF FF FF FF These 16 hex digits are internal to the terminal after encryption as follows (example only): 7A 4C F2 97 31 6E 51 33 These hex digits are then converted to ASCII by prefixing each hex digit with a hex 3: 373A 343C 3F32 3937 3331 363E 3531 3333 If the host protocol is ASCII.ID Card and FIT Definitions Security Features For example assume that the PIN is encrypted and F is used to pad the PIN. If the entered PIN is 4512. the PIN buffer contains these ASCII digits. If the host protocol is EBCDIC. 184 October 2004 U25604-J-Z745-1-7600 . the PIN buffer will contain the following 16 bytes: F77A F44C 6FF2 F9F7 F3F1 F66E F5F1 F3F3 The graphic presentation in a line trace of these bytes will be as follows: 7:4<?297316>5133 ID Card and FIT Definitions This section describes each FIT byte and the associated identification card magnetic data tracks. including the sentinels. Wincor Nixdorf terminals can be equipped to read each track and to write to Track 1/2 and 3.Security Features ID Card and FIT Definitions ID Card Data Tracks A customer card has one. Track 2 can be encoded with up to 40 digits and track 3 can be encoded with up to 107. Each track has a common set of reference delimiters that are specially encoded digits. second field separator. FIT allows a terminal to find the information on the data tracks. Normally. This digit is the longitudinal redundancy digit (LRC). Track 1 can be encoded with up to 79 digits. The end sentinel and LRC are the last two digits. Track 1 contains the customer's name. they differ in capacity because of different encoding densities (bits per inch). the name can be shown on the terminal screen during a transaction. U25604-J-Z745-1-7600 October 2004 185 . and so on. Depending on the terminal programming. The data on a track is found by counting forward from the start sentinel or first field separator or backward from the end sentinel. two or three magnetic data tracks. the end sentinel (ES). Industry standards designate the three tracks as follows: Track 1. and the field separator (FS). separator. These tracks retain sufficient information to identify a corresponding customer's account. The terminal reads the magnetic data digits of each track and stores the information in three data buffers. the separators are designated as the first field separator. The delimiters locate three positions: the start sentinel (SS). Track 2 and Track 3. The tracks have the same physical length. and LRC. The start sentinel is the first track digit. For error checking. there is one other digit on a track. If the track contains more than one separator. FIT (Financial Institution Table) Security Features FIT (Financial Institution Table) The FIT table contains data that specifies institution IDs, information required for PIN verification, and routing information for multi-institution terminal use. A FIT can also contains card formats and indexes indicating where to find specific information on a card. FIT data is down-line loaded to a terminal. Each of the FIT table bytes falls under following categories: q q q q institution identification indexes and lengths related to the ID card format counts, digits, codes and keys for PIN verification and related security reserved for future use Configuration Data Before processing transactions, a terminal must receive configuration data from the host. Configuration data is down-line loaded into the Windows registry location “..\LYNXCI\FIT”. The Financial Institution Tables are part of the configuration data which are added to the personality of the terminal. FIT data are down-line loaded in a Financial Institution Table Load command message, see section ”FIT Data Load” on page 258 for details. ProCash/NDC or ProConsult/NDC stores FIT data in the Windows registry location “..\LYNXCI\FIT”, which represents the FIT library. ProCash/NDC and ProConsult/NDC can store a maximum of 1000 FIT entries (000-999). The highest numbered FIT entry received in a Financial Institution Table Load command message marks the end of the FIT library. After reading an identification card, the terminal scans the FIT library, trying to match the card institution ID field with a particular FIT entry. If the terminal finds a match, it then proceeds to the PIN entry state table. See section ”PIN Entry State (B)” on page 64 in manual part 1 for details. An institution identification scan always begins with FIT 000 and continues until: q q the terminal matches a FIT institution ID the terminal finds a null FIT (a FIT which is not completed during a configuration down-line load) the terminal reaches the end of the FIT library q 186 October 2004 U25604-J-Z745-1-7600 Security Features FIT (Financial Institution Table) FIT Library Restrictions A FIT library has four restrictions. Violating these restrictions may cause unpredictable terminal operation. FIT gap A FIT library should not have any gaps. A gap is one or more zero FIT’s between filled FIT’s. For example, if any sample application requires 27 FIT entries, they must be consecutively numbered from 000 to 026. The terminal then recognizes only FIT 000 to FIT 026 since any scan will find a zero FIT at FIT 027. The sample application could not use FIT 000 to FIT 013 followed by FIT 020 to FIT 032 because of the gap beginning with FIT 014 through FIT 019. Modifying the FIT library The financial institution can modify the FIT configuration data. For example, institution E has FIT’s 006 through 010. If, for some reason, institution E wishes to add another FIT, for example, between 008 and 009, the current FIT’s 009 through 011 must shift one position ahead to become 010 through 012. The inserted FIT becomes the new 009. On the other hand, if institution E wishes to drop a card format, for example, FIT 007, FIT’s 008 through the end of the library must shift back one position. Thus, 008 becomes 007, 009 becomes 008, and so forth. Never delete a FIT by omitting that FIT from a down-line load. This creates a gap in the FIT library at which FIT scanning will stop. Instead of deleting a FIT, renumber them. A FIT may contain all zeros (a zero FIT). The zero FIT must be last, because its PIDDX, PFIID, PSTDX and PINDX fields are not the same as those in the base FIT. An institution may include several zero FIT’s or groups of zero FIT’s within the down-line load. These zero FIT’s may be given values at a later date. Switch FIT’s A FIT entry that has a PFIID of all Fs will match any card. This entry must be the last FIT in the table. No FIT entry with a higher number will be checked. U25604-J-Z745-1-7600 October 2004 187 FIT Data Definitions Security Features Multi Card, Multi Institution Capability An activator card has one to three magnetic data tracks (section ”ID Card and FIT Definitions” on page 184). Several FIT bytes indicate the size and location of the data fields on the tracks. These bytes specify the following: q q q on which track the specific data fields can be found the direction of the data field, relative to a track delimiter the number of track positions occupied Alternate Transaction Sequences A FIT may contain information that causes the terminal to follow alternate sequences of states and screens. This allows the use of transaction sets specifically designed for different activator card formats. This method uses the FIT switch state table. Refer to section ”FIT Switch State (K)” on page 99 for detailed description of this state. FIT Data Definitions The bytes that make up a FIT entry are divided into 16 fields. Many of the fields contain only one byte. A FIT byte represents one of the following: q q q two hex digits with hex values 0 to F for each digit two hex digits with each digit restricted to the decimal values 0 to 9 eight bits possibly divided into bit fields one to seven bits wide Table 51 shows the 16 fields listed by mnemonic, in alphabetical order; Table 52 shows these fields listed according to their positions in the FIT. 188 October 2004 U25604-J-Z745-1-7600 Security Features FIT Data Definitions An index indicates how many digit positions should be skipped over between a track delimiter and the first data digit. Throughout this section, the term displacement means the number of digits to be skipped. A displacement equal to zero means skip no positions; the first data position is adjacent to the track delimiter. A displacement equal to three means skip three positions; the data begins in the fourth position. The following two tables give a short description about the FIT fields: Table 51: Alphabetical FIT references Field Mnemonic PAGDX PANDX PANLN PANPD PCKLN PDCTB PEKEY PFIID PIDDX PINDX PINPD PLNDX PMXPN POFDX PRCNT PSTDX Description ALGO number index (not used) PAN index PAN length PAN pad character PIN check length decimalization table encrypted PIN key institution identification institution index data track locator PIN pad character language code index maximum PIN entry digits offset number index PIN retry count index indirect next state index reserved (not used) Length 1 1 1 1 1 8 8 5 1 3 1 1 1 1 1 1 2 Byte Position 8 12 13 14 10 17-24 25-32 2-06 1 33-35 11 36 9 16 15 7 37-38 U25604-J-Z745-1-7600 October 2004 189 FIT Data Definitions Table 52: FIT fields listed by data track position Security Features Byte Position 1 2-06 7 8 9 10 11 12 13 14 15 16 17-24 25-32 33-35 36 37-38 Length 1 5 1 1 1 1 1 1 1 1 1 1 8 8 3 1 2 Field Mnemonic PIDDX PFIID PSTDX PAGDX PMXPN PCKLN PINPD PANDX PANLN PANPD PRCNT POFDX PDCTB PEKEY PINDX PLNDX Description institution index institution identification indirect next state index ALGO number index (not used) maximum PIN entry digits PIN check length PIN pad character PAN index PAN length PAN pad character PIN retry count index offset number index decimalization table encrypted PIN key data track locator language code index reserved (not used) Institution Index (PIDDX) PIDDX is the displacement from the delimiter specified by PINDX (byte 0, low-order digit) to the start of the activator card institution identification field. PIDDX comprises two hex digits with values 00 to 7F. 190 October 2004 U25604-J-Z745-1-7600 Security Features FIT Data Definitions Institution Identification (PFIID) PFIID is the institution identification number. After reading an activator card, the terminal scans its FIT library for a PFIID that matches the institution identification number on the activator card. PFIID contains ten hex digits (two per byte). Each digit must have a hex value of 0 to 9 or F (A, B, C, D and E are not permitted). An F in any position means “match all”; that is, any value on the activator card at that position matches. FIT's that have Fs in PFIID should be at the higher numbered positions in the FIT library. For example, a PFIID that is all Fs should be the last FIT in the library because all activator cards match the PFIID. FIT Switch Index (PSTDX) PSTDX indicates the next state location in the FIT Switch state table. See section ”FIT Switch State (K)” on page 99 for details. PSTDX comprises two hex digits with values 00 to 06 and . (PSTDX is not a displacement on the ID card.) Maximum PIN Entry Digits (PMXPN) PMXPN is the maximum number of PIN digits that the terminal accepts from a customer on any one PIN entry. PMXPN must be greater than or equal to the value of the five low-order bits of PCKLN. PMXPN comprises two hex digits with values of 04 to 10 for Diebold PIN block or 84 to 8C for ANSI PIN block. With the data security module installed, the PMXPN values are 04 to 0F. ProCash/NDC or ProConsult/NDC identifies a null FIT if PMXPN = 0. The highest order bit of PMXPN indicates whether Diebold or ANSI PIN block is used. The bit definitions are as follows: 0 - Diebold PIN block 1 - ANSI PIN block An institution may issue PIN's shorter than PMXPN. These are variable-length PIN's. Customers with variable-length PIN's enter their PIN digits, then press operation key A to signal the end of the PIN entry. U25604-J-Z745-1-7600 October 2004 191 FIT Data Definitions Security Features PIN Check Length (PCKLN) PCKLN provides the following information to the terminal: The number of PIN digits to be verified. This number must be less than or equal to the maximum PIN length (PMXPN). If this number is less than PMXPN, the Diebold PIN verification process checks the last digits entered up to the number indicated by the PCKLN field. For example, if the customer has a PIN of 1346875 and the PCKLN is 4, the process will check the last four digits entered, 6875. The number of digits in the offset number. This number is always equal to the number of PIN digits verified. The PIN verification algorithm to be used for terminal PIN verification. This information is in two bit fields: 3 BITS 5 BITS The high-order three-bit field indicates the type of local terminal PIN verification to be used. BITS 000 001 010 011 100 101 110 111 ALGORITHM DES not supported Diebold (not supported) reserved not supported reserved reserved reserved 192 October 2004 U25604-J-Z745-1-7600 Security Features FIT Data Definitions DES and Diebold - The low order five-bit field is the number of PIN digits verified and the number of digits in the offset. The value must be less than or equal to PMXPN. If the entire PCKLN byte is zero, the terminal does not perform local PIN verification. TERMINAL VERIFICATION none DES DES (EDM) Diebold HEX VALUE RANGE 00 04-10 04-0F 40, 44 U25604-J-Z745-1-7600 October 2004 193 FIT Data Definitions Security Features PIN Pad Character (PINPD) PINPD is only used for DES encryption of PIN’s in messages sent to the network. PINPD is reserved and equal to zero for other PIN verifications. PINPD comprises two hex digits. The high-order digit indicates the message encryption type, the key(s), and the use of the message coordination number. HIGH-ORDER BITS HEX TYPE OF ENCRYPTION USE AS KEY 1 USE AS KEY 2 USE COORD.NO. 0000 0010 0011 0100 1000** 1010** 1011** 1100 0 2 3 4 8 A B C single double double none single double double none COM MASTER PIN* none COM MASTER PIN* none none COM COM none none COM COM none no no no no yes yes yes yes * PIN key is PEKEY decrypted by master key ** Not applicable with ANSI PIN block The low-order digit pads the PIN to the right in the PIN buffer of the terminal. When ANSI PIN block has been selected, PINPD is not used to pad the PIN. PINPD must be used to select the type of ANSI PIN block encryption. The PIN buffer stores the customer-entered PIN digits in an equal number of positions. Then, the pad digits concatenate to the PIN digits to yield 16 PIN buffer positions. When the message coordination number is not in the message sent to the network, the terminal encrypts (either single or double) these 16 PIN buffer digits before transmission. The 16 PIN buffer digits can also be sent without encryption, but this is not recommended. When the message coordination number is in the message to the network, the message coordination number is inserted in the PIN buffer before encryption. In effect, the PIN and pad shift right one position, loosing one pad digit. The valid range of hex values for PINPD includes 00 to 0F, 20 to 4F, 80 to 8F, and A0 to CF. 194 October 2004 U25604-J-Z745-1-7600 whichever count is the least.PANLN comprises two hex digits with values 00 to 10. Diebold . q U25604-J-Z745-1-7600 October 2004 195 . When PANLN equals 1F.Security Features FIT Data Definitions PAN Index (PANDX) PANDX is the displacement from the delimiter specified by PINDX (byte 1. the PAN is obtained as follows: – locate the first field separator on the specified track.PANLN comprises two hex digits with values from 00 to 0C or 1F. PANLN has the following value limits: q q DES . When PANLN equals 1F. Depending on PIN verification. PANLN must be greater than or equal to the value of the five low-order bits in PCKLN. – the delimiter and direction specified in PINDX and PANDX do not apply. ANSI PIN block . loworder digit) to the start of the ID card PAN field (those PAN digits used for PIN verification). – count back 13 digits or to the first digit before the start sentinel. the terminal uses all PAN digits from the PANDX starting position to the field separator that follows. – the PAN will include all the digits from this point up to but not including the last digit before the first field separator. PAN Length (PANLN) PANLN is the number of PAN digits to be used for terminal PIN verification. PANDX comprises two hex digits with values 00 to 7F.PANLN comprises two hex digits with values 04 to 13 or 1F. stop at the retry value in PIN entry state table. but in the PIN entry state table. Count up on each retry. 196 October 2004 U25604-J-Z745-1-7600 . The 16-position padded PAN is then encrypted to produce a generated (natural) PIN. The high-order bit of PRCNT indicates the retry count conditions.PANPD comprises two hex digits.PANPD is the algorithm number (ALGO) when PAGDX equals hex FF. thus. high-order digit) to the ID card PIN entry count field. the PIN entry count is not on the ID card. The low-order digit pads those PAN digits specified by PANLN (to 16 positions). PIN Retry Count Index (PRCNT) The low-order seven bits of PRCNT are the displacement from the delimiter specified by PINDX (byte 1. PRCNT comprises two hex digits with values 00 to 7F (MINTS) or 80 to FE (ISO) or FF. PANPD is not used and is. When PAGDX does not equal FF. When PRCNT is hex FF. HI-ORDER BIT 1 0 CARD RETRY COUNT CONDITION FORMAT ISO MINTS Count down on each retry.FIT Data Definitions Security Features PAN Pad Character (PANPD) PANPD has three definitions (depending on the PIN verification scheme used): DES . PANPD comprises two hex digits with each digit restricted to values 0 to 9 (hex values A to F not permitted). DIEBOLD . The PANPD values are 00 to 99. The high-order PANPD hex digit specifies which of the following encryption keys is used: 0 = use the PIN key (decrypted PEKEY) 8 = use the master key Other hex values of either 00 to 0F or 80 to 8F. equal to zero. stop at zero. Security Features FIT Data Definitions Offset Number Index (POFDX) POFDX is the displacement from the delimiter specified by PINDX (byte 2, loworder digit) to the start of the ID card offset field. POFDX comprises two hex digits with values 00 to 7F or FF. When the value of POFDX equals hex FF, the offset is not used. Decimalization Table (PDCTB) PDCTB is the DES decimalization table containing a pattern of decimal digits (two per byte, hex values A to F not permitted). The institution is responsible for producing values for PDCTB. A sample value follows: 01 01 23 23 45 45 67 67 89 89 AB 01 CD 23 EF 45 (standard hex digits) (decimalized digits) The digit positions map the corresponding hex digits from the DES process to ensure that only decimal digits result. Each decimal digit (0 to 9) should appear at least once, but not more than twice. Encrypted PIN Key (PEKEY) PEKEY is the encrypted PIN key. The master key encrypts the PIN key. The PIN key encrypts the PAN digits specified by PANDX and PANLN to yield a generated PIN for DES terminal PIN verification. PEKEY comprises 16 hex digits (two per byte), with each digit having a hex value of 0 to F. For non-DES operation PEKEY is reserved and all bytes must be hex 00. The institution is responsible for providing PEKEY values. U25604-J-Z745-1-7600 October 2004 197 FIT Data Definitions Security Features Data Track Locator (PINDX) PINDX comprises six hex digits (two per byte). Five of the six PINDX digits specify the ID card data track delimiter to be used in conjunction with five corresponding indexes (PAGDX, PIDDX, PRCNT, PANDX, PLNDX and POFDX). PINDX Byte FIT byte 33 FIT byte 34 FIT byte 35 Hi-Order HEX digit PAGDX (ALGO) PRCNT (RETRY) LO-Order HEX digit PIDDX (ID) PANDX (PAN) PLNDX (LANGUAGE) POFDX (OFFSET) The four bits of each non-reserved digit define a track, a delimiter and a direction from that delimiter. Digit Bits 00XX 01XX 10XX 11XX XX00 XX01 XX10 XX11 Bit Pair Definition Start sentinel, count forward First field separator, count forward End sentinel, count backward Reserved Track 2 Track 3 Track 1 Reserved Language Code Index (PLNDX) The Language Code Index specifies the offset for the language code on the ID card. This field can be used in conjunction with state V (Language Select from Card state). The V state sets the screen group of multi language screens that should be displayed during transactions. PLNDX is in range of 01-7F hex. The value of 00 hex is not allowed if the language code is used. The value 7F hex means zero if the language code is used and the search is backwards from an end sentinel only. 198 October 2004 U25604-J-Z745-1-7600 Security Features Message Authentication (MAC) Message Authentication (MAC) Overview Message authentication minimizes the risk of unauthorized tampering with the messages sent between the terminal and the network. Message modification and message replay are two methods of message tampering. Message modification is where the data communication lines between the terminal and next node are tampered with so that values in a message can be changed for fraudulent purposes. Message replay is where entire messages are copied from a previous transaction and retransmitted later for fraudulent purposes. To help minimize the risk of message tampering, two fields are added to the messages, a time variant number and a Message Authentication Code (MAC). The time variant number is a randomly-generated eight-digit hex number. This number is generated by the terminal for each transaction request message. The MAC is an eight-digit hex number containing the result of a MAC calculation on the message. For example, the transaction request message is formed and includes a time variant number. Once this is done, a DES operation is performed on the message using the master key and the DES algorithm. The result of this operation is the MAC. The MAC is placed in the MAC data field at the end of the message. Upon receiving the message, the network performs the same DES operation on it. The network then compares the result of this DES operation with the MAC contained in the MAC data field. If the two match, the network is assured that the message is from a valid terminal and that it has not been tampered with. The network then returns the time variant number with its Transaction Reply command. The ATM can check that this is the same time variant number sent in the transaction request. This ensures that the entire process is authentic. Messages that can be authenticated are as follows: q q q q q q Transaction Request command Transactioen Reply command State Table Load command FIT Table Load command MAC Field Selection Load command Solicited Status messages U25604-J-Z745-1-7600 October 2004 199 Message Authentication (MAC) Security Features The ANSI standard X9.9 describes the procedures and provides the algorithm used to calculate the MAC data. A MAC master key is used with this algorithm to perform the MAC calculation. This master key is down-line loaded from the network in an Encryption Key Load command message. MAC flags Message Authentication is controlled by some configuration parameters which have to be set in PARAC configuration file ’CUSTOM.PPF’. The following table shows the MAC flags to be activated: Table 53: MAC flags definition NDC PARAMETER in FLAG CUSTOM.PPF 1 CHECK_TVN_MAC VALUE 0 DESCRIPTION Do not check TVN in Transaction reply messages, or MAC in Transaction reply, State Table or FIT Load messages. Check TVN in Transaction reply messages, or MAC in Transaction reply, State Table or FIT Load messages. Do not send the TVN and MAC data in Transaction Request messages Send the TVN and MAC data in Transaction Request messages Do not check the Security Terminal Number in Tran. Reply messages Check the Security Terminal Number in Tran. Reply messages The MAC calculation is performed on the whole message The MAC calculation is performed on the fields that are specified in the MAC field selection table downloaded from host. Do not send the TVN and MAC on solicited device status messages Send the TVN and MAC on solicited device status messages Do not include the Security Terminal Number in terminal to host messages Include the Security Terminal Number in terminal to host messages Calculate the MAC in EBCDIC Calculate the MAC in ASCII 1 2 SEND_TVN_MAC 0 1 8 CHECK_MACHINE_NO 0 1 9 MAC_FLD_SELECTED 0 1 10 SEND_TVN_MAC_SOL 0 1 SEND_MACHINE_NO (not configurable via ProCash/NDC-SOP or ProConsult/NDC-SOP) MAC_ASCII (not configurable via ProCash/NDC-SOP or ProConsult/NDC-SOP) 0 1 0 1 200 October 2004 U25604-J-Z745-1-7600 Security Features Message Authentication (MAC) Security Terminal Number (Machine Number) Message Authentication uses a six digit Security Terminal Number in the messages which has to be included to build the MAC field. The Security Terminal Number can be entered in the User Exit functions item ’Enter Machine no.’ of ProSop. If you have configured the ProCash/NDC-SOP, refer to the ProCash/SOP Service & Operating User Guide for details. See also ProCash/NDC ProConsult/NDC Installation manual section [HARDWARE_CONFIGURATION] about MACing activation. MAC data field There are two additional fields in the messages for message authentication. The first field, the MAC data field, contains the result of a MAC calculation performed on the message. This MAC calculation uses the MAC master key and the DES algorithm to obtain its result. The MAC data field is calculated by performing a MAC calculation on the message from the first field after the protocol-dependent header (on a Transaction Reply command this is the Transaction Reply command identifier) up to but not including the field separator preceding the MAC data field. The MAC data field is always the last field of the message preceding the end of text (ETX). The digits on which the MAC calculation is performed are the same digits that appear on the communications line. For example, if the protocol is IBM 3275 EBCDIC, the digits that are authenticated will be EBCDIC; if the protocol is IBM 2265 ASCII, the digits will be ASCII. Time variant number If the message is a transaction request or Transaction Reply command, another field, the time variant number, is also included in the message. The time variant numbers are generated randomly by the terminal. If a terminal expects a MAC in a message and does not receive it, the terminal will reject the message. On the other hand, if a terminal does not expect a MAC but receives it, the terminal operation is not guaranteed. Refer to your terminal programming manual for more details on the messages. U25604-J-Z745-1-7600 October 2004 201 Message Authentication (MAC) Security Features Typical Message Authentication Procedure The following steps describe a typical message authentication procedure. q If the terminal is sending a transaction request message, it first generates a time variant number and inserts the number after the third field separator of the message. The terminal performs a MAC calculation on the transaction request message. The result of this calculation is placed at the end of the message in the MAC data field. When the network receives the transaction request message, it performs a MAC calculation on the message. The network compares the result of the MAC calculation with the data in the MAC data field. If the two are the same, the network generates a Transaction Reply command message instructing the terminal to perform the desired transaction. If not, a Transaction Reply command message is sent directing the customer to try another transaction. The network inserts the time variant number received in the transaction request message into the Transaction Reply command message. The network performs a MAC calculation on the Transaction Reply command message. The result of this calculation is placed at the end of the message in the MAC data field. When the terminal receives the Transaction Reply command message, it performs a MAC calculation on the message. The terminal compares the result of the MAC calculation with the data in the MAC data field of the Transaction Reply command message. If the two are the same, the terminal then continues to step 9. If not, the terminal sends a command reject in a solicited status message. The terminal then compares the time variant number sent in the transaction request message to the time variant number received in the Transaction Reply command message. If the two are the same, the terminal services the Transaction Reply command. If not, the terminal sends a command reject in a solicited status message. q q q q q q q q 202 October 2004 U25604-J-Z745-1-7600 Security Features Triple DES operation MACing for State and FIT Table Load commands For the State Table Load and FIT Table Load command messages, only the MAC data field is used for message authentication. The network performs a MAC calculation on the Load command message being sent and puts the result in the MAC data field. When the terminal receives the message, it performs a MAC calculation on the message. The terminal then compares the result of the MAC calculation with the MAC data field. If the two are the same, the terminal accepts the Load command message. If not, the terminal transmits a command reject in the solicited status message. Triple DES operation Since release 1.2/10 ProCash/NDC is able to operate in triple DES mode. For triple DES operation, following minimum conditions are required: q The EPP hardware of the system must be able to operate with double length triple DES keys (minimum firmware version 4.23). Triple DES mode has to be enabled in the installation dialog of ProCash/NDC at the beginning of the installation process. Refer to ProCash/NDC Installation manual for details about Triple DES configuration. The host system must be able to download double length triple DES keys to the terminal. Local security keys (Master-Key , COM-Key) have to be entered via Triple DES key entering method. q q q EMV capability Since release 1.3/00 ProCash/NDC supports transactions with EMV data. Please refer to Wincor Nixdorf / Diebold D91x Message Format Extension for EMV for detailed descriptions how to integrate EMV support. U25604-J-Z745-1-7600 October 2004 203 Remote Key Loading (RKL) capability Security Features Remote Key Loading (RKL) capability Since release 1.3/00 ProCash/NDC supports Remote Key Loading (RKL). Please refer to Wincor Nixdorf / Diebold D91x Message Format Extension for RKL for detailed descriptions how to integrate RKL. 204 October 2004 U25604-J-Z745-1-7600 Messages This section describes the messages that make up the communications interface between the Wincor Nixdorf terminals and the controlling network. Unless otherwise indicated, information refers to all versions. The terminal gathers all the necessary information for a transaction request. Typically this information consists of the following: q q q account card data including the Primary Account Number (PAN) the Personal Identification Number (PIN) various terminal keyboard inputs Figure 2: “Transaction message flow” on page 206 is an example of a typical message exchange sequence. The Transaction Request message is sent to the network. The network responds to a Transaction Request message with a Transaction Reply command message. The Transaction Reply command message tells the terminal how to accomplish the requested transaction. After the terminal completes the transaction with the customer, it sends a solicited status message to the network. The basic message formats used in the system are fixed. These formats contain the necessary control characters to conform with most protocol formats. This section shows the format for each message type used in the system. Messages can travel either from the terminal to the network, or from the network to the terminal. Messages from Terminal to Network The terminal transmits three message types. q q q Solicited Status messages Unsolicited Status messages Transaction Request messages U25604-J-Z745-1-7600 October 2004 205 terminal formats request Transaction Request message Make decision to allow or disallow transaction Complete transaction as directed. The data for this code must be a valid character as described in this manual. --- : ‘ ‘ 206 October 2004 U25604-J-Z745-1-7600 . Table 54: Code conventions Code Symbols X Description This symbol indicates that the terminal ignores the data. Three dashes indicate that the field data is dependent on the specific transaction performed and the valid entries for the field. format status message Transaction Reply message Solicited Status message Record completed transaction The following subsections illustrate these messages in tabular form.Messages from Terminal to Network Figure 2: Transaction message flow Messages TERMINAL Consumer enters card and PIN NETWORK Consumer enters request data. The notes in the following table apply to all tables. The colon symbol indicates that the following two digits are a hexadecimal number. Refer to the field descriptions in this manual. An example of an invalid Wincor Nixdorf terminal character for this code is a zero (hex 00). Single quotation marks indicate that the characters enclosed within them are graphic characters from an ASCII or EBCDIC code set. Numeric parenthetic expressions following VAR show the maximum number of characters allowed in the field. VAR (Numeric) U25604-J-Z745-1-7600 October 2004 207 .Messages Messages from Terminal to Network [ ] Brackets indicate that the field is optional. The data for this code must be a valid character as described in this manual. The field can be deleted completely from the message without affecting the format or meaning of the message. It will be skipped by the emulation. VAR indicates that the length of the field is variable. An example of an invalid Wincor Nixdorf terminal character for this code is a zero (hex 00). Messages from Terminal to Network Figure 3: Terminal to network messages Messages Terminal to network messages Solicited Status TERMINAL Unsolicited Status HOST Transaction Request 208 October 2004 U25604-J-Z745-1-7600 . 8 or 12 1 Var (16 max) 1 Var (32 max) 1 U25604-J-Z745-1-7600 October 2004 209 . The following table shows the data fields and sequence of fields for a Transaction Request message. Table 55: Transaction Request message Description solicited/unsolicited ID message identifier field separator (FS) logical unit number (LUNO) field separator (FS) field separator (FS) time variant number field separator (FS) top-of-form flag message coordination number field separator (FS) track 2 data field separator (FS) track 3 data field separator (FS) operation code buffer field separator (FS) whole-amount/cents keyboard entry field separator (FS) PIN buffer (Buffer A) field separator (FS) general purpose buffer B field separator (FS) Code ’1’ ’1’ :1C --:1C :1C [---] :1C ----:1C [VAR] :1C [VAR] :1C [---] :1C [---] :1C [VAR] :1C [VAR] :1C No. The maximum length of this message is 2000 characters (bytes). of Characters 1 1 1 3 or 9 1 1 8 1 1 1 1 Var (40 max) 1 Var (106 max) 1 0 or 8 1 0. The network answers a Transaction Request with a Transaction Reply command to the terminal.Messages Messages from Terminal to Network Transaction Request message This message contains data which the network needs to authorize a customer transaction at the terminal. Solicited/unsolicited message field Field size: 1 character Valid range: 1-2 Description: This field tells the network whether the message is solicited or unsolicited. [2] These bytes are only sent if MACing is used The following paragraphs describe the fields in the Transaction Request message. The valid entries for this field are as follows: 1 .Messages from Terminal to Network Messages Description general purpose buffer C field separator (FS) track 1 data buffer (1) identifier track 1 data buffer field separator (FS) Transaction status identifier Last transaction status data field separator (FS) CSP data ID ’U’ CSP data field separator (FS) confirmation CSP data ID ’V’ confirmation CSP data field separator (FS) MAC data Code [VAR] [:1C] [1] [VAR] [:1C] [2] [VAR] [:1C] [:1C] [VAR] [:1C] [:1C] [VAR] [:1C] [---] No.solicited message In case of a Transaction Request message. 210 October 2004 U25604-J-Z745-1-7600 . this field will be 1. of Characters Var (32 max) 1 1 Var (79 max) 1 [1] 1 [1] 25 1 1 Var (16 max) 1 1 Var (16 max) 1 [2] 8 [2] [1] [1] These bytes are only sent if the download option is selected in the „Enhanced Configuration Parameters“ load message.unsolicited message 2 . See chapter ”Security Features” from page 175 for further information. If a machine number is entered. this field will contain nine characters with the last six characters of this field being the terminal number used for MACing. Time variant number Field size: 8 characters Valid range: See description Description: This is an eight-character field. See section ”Message Authentication (MAC)” on page 199 for further information. The only valid value for the Transaction Request message is 1. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal.Messages Message identifier field Field size: 1 character Messages from Terminal to Network Valid range: 1 Description: This one-character data field defines the type of message being transmitted. containing hexadecimal characters. randomly generated by the ATM. U25604-J-Z745-1-7600 October 2004 211 . ‘>‘. 212 October 2004 U25604-J-Z745-1-7600 . The valid range for the coordination numbers is graphic ‘1’ through ‘9’. 1 . I . <" =. The host or controller must include the corresponding coordination number when responding with a transaction reply message.not printing this transaction at the top of the transaction record form. . If the extended range for the message coordination number field is enabled (Enhanced Configuration Parameters Load message). ‘:’. If the coordination numbers do not match.printing transaction at the top of the transaction record form. the terminal sends a solicited status message with a command reject status. Track 2 data field Field size: Variable Valid range: See description Description: This variable length data field contains up to 40 characters of data from track 2 of the magnetic stripe on the customer’s account card. and ‘?’ (ASCII 31 through 3F). The valid values are as follows: 0 . This field includes the data from the start sentinel to the end sentinel inclusive.Messages from Terminal to Network Top-of-form (TOF) flag Field size: 1 character Messages Valid range: 0-1 Description: This data field informs the network if this transaction is printing at the top of the transaction record form. The terminal assigns a different coordination number to each successive transaction request on a rotating basis.’. Message coordination number Field size: 1 character Valid range: ASCII 31-3F (or extended range 31-7E) Description: This is a character assigned by the terminal to each transaction request message. the valid range is ASCII 31 trough 7E. The Preset Operation Code state can clear and preset any of the positions in the operation code buffer. States D.Messages Track 3 data field Field size: Variable Messages from Terminal to Network Valid range: See description Description: This is variable length field contains up to 106 characters of data from track 3 of the magnetic stripe. E and Y determines the contents of this field. Operation code buffer Field size: 0 or 8 characters Valid range: See description Description: The operation code buffer field contains the data collected in the operation code buffer as a result of function display keys (FDK’s) pressed. which identifies the transaction selected by the consumer. For detailed descriptions refer to following sections: “Pre-Set Operation Code Buffer State (D)” on page 72 “Four FDK Selection Function State (E)” on page 78 “Eight FDK Selection State (Y)” on page 132 U25604-J-Z745-1-7600 October 2004 213 . State E or Y determine in which position and how many graphics are stored in the operation code buffer when an FDK is pressed. This field includes the data from the start sentinel to the end sentinel inclusive. The field can be either zero or eight characters long. The PIN buffer is also known as general purpose buffer A. B. this field contains up to 32 digits that were entered by the customer. D. E (cancel) or T (time-out)). C. The content of this field is determined by the Amount Entry state. The data is right-aligned with zeros to fill unused positions on the left. this field can be either zero or twelve characters long. General purpose buffer B Field size: Up to 32 characters Valid range: See description Description: The contents of the variable-length general purpose buffer B field depend on whether the consumer message is being sent in response to an interactive transaction screen. this field only contains up to 32 digits that were entered by the customer. If it is not being sent in response to an interactive transaction screen. 214 October 2004 U25604-J-Z745-1-7600 . the whole-amount and Cents keyboard entries field can be either zero or eight characters long. this field also contains the character representing the operation key pressed or a time-out (A. This field identifies the whole-amount and cent amount entered at the keyboard.Messages from Terminal to Network Whole-amount and Cents keyboard entry field Field size: 0 or 8. If the amount buffer size feature is selected. if less than 32 digits were entered. PIN buffer Field size: 0 or up to 16 characters Valid range: See description Description: The variable-length PIN buffer field will contain either no characters (if local PIN check is used) or the 16-character encrypted or decrypted PIN (if remote PIN check is used). 0 or 12 Messages Valid range: See description Description: If the amount buffer size feature is not selected. and. If it is being sent in response to an interactive transaction screen. U25604-J-Z745-1-7600 October 2004 215 . This field includes the data from the start sentinel to the end sentinel inclusive. Track 1 data field Field size: Variable (79 maximum) Valid range: See description Description: This variable-length field contains up to 79 characters of data from the track 1 magnetic stripe. Transaction status data identifier Field size: 1 Valid range: 2 Description: Identifies the following data in the next fields as Transaction status data of the previous transaction. if so selected by the information entry state. Track 1 data buffer identifier (1) Field size: 1 character Valid range: 1 Description: This one-character field identifies the data that follows in the next field as track 1 data.Messages General purpose buffer C Field size: Up to 32 characters Messages from Terminal to Network Valid range: See description Description: The variable-length general purpose buffer C field contains up to 32 digits that were entered by the customer. 1 byte Contains one byte identifying what the last known status message sent from the terminal was.none sent ’1’ .good termination sent ’2’ .error status sent ’3’ .Messages from Terminal to Network Last transaction status data Field size: 25 Messages Valid range: See description Description: Contains status data relating to the previous transaction performed by the terminal. If this field is selected in the transaction request state table and no CSP has been requested only this field will be present.4 bytes Contains the four-digit serial number of the last transaction processed by the terminal.transaction reply rejected q q Last transaction notes dispensed . The field can contain the following values: ’0’ . CSP data ID ’U’ Field size: 1 character Valid range: ’U’ Description: The value ’U’ in this field identifies the following field as the first Customer selected PIN data. 216 October 2004 U25604-J-Z745-1-7600 .20 bytes Contains four five-digit decimal counts defining the notes dispensed on the last transaction. It contains the following data: q Last transaction serial number . CSP data Field size: 16 characters Valid range: See description Description: This field contains an encrypted 16 character PIN. Last status issued . If this field is selected in the transaction request state table and no CSP has been requested only this field will be present.Messages Confirm CSP data ID ’V’ Field size: 1 character Messages from Terminal to Network Valid range: ’V’ Description: Confirmation CSP data ID ’V’ is the field that identifies the following field as the second Customer selected PIN data. U25604-J-Z745-1-7600 October 2004 217 . MAC data field Field size: 8 characters Valid range: See description Description: This eight-character field contains hexadecimal characters that represent the MAC calculation of the transaction request message. See the section ”Message Authentication (MAC)” on page 199 for additional details. This field contains an encrypted 16 character PIN. Confirmation CSP data Field size: 16 characters Valid range: See description Description: Confirmation CSP data. If the CSP state indicates that loacal verification of the two CSP’s is to be carried out only the identifier will be sent if requested by the transaction request state. If an error is detected during the last function performed. error status data pertaining to the terminal is inserted into the status message. If the functions are performed as commanded. The maximum length of this message is 256 characters. The network expects a reply concerning the results of the last function performed through a Solicited Status message. of Characters 1 1 1 3 or 9 1 1 1 1 VAR 1 [1] 8 [1] [1] These bytes are only sent if MACing is activated for the solicited message. The following tables list the data field associated with the Solicited Status message and shows field positions. 218 October 2004 U25604-J-Z745-1-7600 . a ready status indicator is inserted into the status message.Messages from Terminal to Network Messages Solicited Status messages Solicited Status messages are sent from the terminal as the response to command messages received from the network. The following table contains the fields of the solicited status message: Table 56: Solicited Status message Description solicited/unsolicited ID message identifier field separator (FS) logical unit number (LUNO) field separator (FS) field separator (FS) status descriptor field separator (FS) status information field separator (FS) MAC data field Code ‘2’ ‘2’ :1C --:1C :1C --[:1C] [---] [:1C] [---] No. See chapter ”Security Features” from page 175 for additional details.solicited message In the case of the solicited status message.Messages Messages from Terminal to Network The following paragraphs describe the fields for the solicited status message. If a machine number is entered. The only valid value for the Solicited Status message is 2. this field will contain nine characters with the last six characters of this field being the terminal number. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three character data field is defined in the configuration data transmitted to the terminal. The valid entries for this field are as follows: 1 . Solicited/unsolicited message field Field size: 1 character Valid range: 1-2 Description: This field tells the network whether the message is solicited or unsolicited. U25604-J-Z745-1-7600 October 2004 219 .unsolicited message 2 . this field will be 2. Message identifier field Field size: 1 character Valid range: 2 Description: This one-character data field defines the type of message being transmitted. ‘A’ .device fault or configuration information.ready. The terminal can send this character only if MAC is enabled.an illegal command . Logs.configuration data while “In Service” mode Some additional general command reject conditions are listed in section ”Specific Command Reject Conditions” on page 280. this character indicates successful completion of the Transaction Reply command. For example. ‘C’ .Messages from Terminal to Network Status descriptor Field size: 1 character Messages Valid range: See description Description: This one-character field describes the terminal status as it responded to the command.ready.a Transaction Reply command message . The terminal can send this character in response to any of the following messages: . This character indicates the unsuccessful completion of either an terminal command or a Transaction Reply command. This character indicates a terminal device is reporting an abnormal status or that configuration information follows. Supply Counters or terminal configuration information.illegal data from the network . This is sent in response to terminal commands requesting Tallies. a graphic ‘A’ can be inserted into the status descriptor if the terminal receives any of the following: . ‘9’ .specific MAC command reject. This character indicates the unsuccessful completion of a message because of a message authentication code (MAC) failure or a time variant number failure. When separate ready for Transaction Reply commands is selected. This character indicates the successful completion of either a terminal command or a Transaction Reply command when the separate ready for Transaction Reply command is not selected.Terminal State. ‘B’ .general command reject. 220 October 2004 U25604-J-Z745-1-7600 .a State Tables Load command message .a FIT Data Load command message ‘F’ . The valid values are as follows: ‘8’ . Terminal State) Field size: VAR Valid range: See description Description: The status information will vary according to which of the following terminal commands has been received by the terminal: q send configuration information q q q q q send supply counters send error log information send date/time information send configuration ID send Software ID and release number See section ”Solicited Status (terminal state)” on page 303 for detailed description of status information.Messages Messages from Terminal to Network Status information (status descriptor ‘F’ . U25604-J-Z745-1-7600 October 2004 221 . MAC data field Field size: 8 characters Valid range: See description Description: This eight-character field contains hexadecimal characters that represent the MAC calculation of the transaction request message. 222 October 2004 U25604-J-Z745-1-7600 .Device Fault) Field size: 1 character Messages Valid range: See description Description: If the status descriptor = ’8’.receipt printer .deposit .envelope dispenser See section ”Solicited Status (device fault)” on page 331 for detailed description of status information.statement printer . See the section ”Message Authentication (MAC)” on page 199 for additional details. this field identifies device reporting abnormal status of following devices: ‘D’ ‘E’ ‘F’ ’G’ ’H’ ‘V’ ’\’ .journal printer .Messages from Terminal to Network Status information (status descriptor ‘8’ .card reader/writer .cash dispenser . The valid entries for this field are as follows: 1 .unsolicited message 2 . Solicited/unsolicited message field Field size: 1 character Valid range: 1-2 Description: This field tells the network whether the message is solicited or unsolicited.solicited message In the case of the Unsolicited Status message. The following table contains the status fields of unsolicited messages: Table 57: Unsolicited Status message Description solicited/unsolicited ID message identifier field separator (FS) logical unit number (LUNO) field separator (FS) field separator (FS) status information Code ‘1’ ‘2’ :1C --:1C :1C --- No.Messages Messages from Terminal to Network Unsolicited Status messages This message is transmitted to the network when a change of status occurs at the terminal. of Characters 1 1 1 3 or 9 1 1 VAR The following paragraphs describe the fields in the unsolicited status message. U25604-J-Z745-1-7600 October 2004 223 . Maximum length is 256 characters. this field will be 1. If a machine number is entered. See chapter ”Security Features” from page 175 for additional details. The only valid value for the unsolicited status message is 2. refer to section ”Unsolicited Device Status” on page 335 of NDC device status.Messages from Terminal to Network Message identifier field Field size: 1 character Messages Valid range: 2 Description: This one-character data field defines the type of message being transmitted. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. For details of this field. this field will contain nine characters with the last six characters of this field being the terminal number. 224 October 2004 U25604-J-Z745-1-7600 . Status information Field size: Variable Valid range: See description Description: This field contains the device identifier and device status information. Load command (message ID ’3’) See the following figure for an overview. Screens. Terminal command (message ID ‘1’) 3. and terminal configuration data download commands are part of configuration data during terminal startup. 1. Transaction Reply command (message ID ‘4’) 2. The Configuration ID Number Load command is used to change the configuration ID after terminal startup and whenever new configuration data is sent to the terminal. There are several download commands used in communications between network and terminal. FIT’s. Encryption Key Load commands are used during terminal startup (or for dynamic key exchange used by some customers) to load new encryption keys. States. Load commands can be sent as interactive transaction responses that are used during system operation to satisfy transaction requests.Messages Network to Terminal messages Network to Terminal messages There are three basic message types transmitted from the network to the terminal. Figure 4: Network to terminal commands Network to terminal messages Load commands TERMINAL Transaction Reply commands HOST Terminal commands U25604-J-Z745-1-7600 October 2004 225 . of Characters 1 1 1 3 1 3[1] 1 3 1 VAR not used not used 1 4 1 3 226 October 2004 U25604-J-Z745-1-7600 . Two conditions must be fullfilled for the transmission of the Transaction Reply command message to the terminal. q The customer has entered all the required data for a specific transaction request. The paragraphs following the tables describe the fields in the Transaction Reply command message. Table 58: “Transaction Reply command message” on page 226 lists the fields of the Transaction Reply command message. q The Transaction Reply command acts as an authorization to the terminal to complete the transaction.Network to Terminal messages Messages Transaction Reply command (message ID ‘4’) The Transaction Reply command message is sent to the terminal in response to a Transaction Request message. Table 58: Transaction Reply command message Description Transaction Reply command identifier response flag field separator (FS) logical unit number (LUNO) field separator (FS) message sequence number field separator (FS) next state ID (000-254. It is prohibited to transmit a Transaction Reply command message without the end of text character. The request has been sent to the network. 256-999) field separator (FS) number of bills to dispense group separator (GS) number of coins to dispense field separator (FS) transaction serial number function identifier screen number (010-999) Code ‘4’ [X] :1C [X] :1C [X] :1C [---] :1C [---] [:1D] [---] :1C ----[---] No. The Transaction Reply command message is restricted to a length of 600 characters. 4) (8) printer data group separator (GS) printer flag (0 . of Characters VAR 1 1 1 1 VAR (580 max) 1 1 VAR 1 1 VAR 1 1 VAR 1 1 VAR (106 max) 1 not supported not supported not supported not supported not supported not supported not supported not supported not supported not supported field separator (FS) buffer identifier (4) track 3 data field separator (FS) buffer identifier (E) document destination lift front/rear image(s) archive lifted front/rear image(s) lift zones in image list archive lifted image list zones check magnetism check zone verification report candidates/identify document entry retries U25604-J-Z745-1-7600 October 2004 227 .4) printer data group separator (GS) [2] printer flag (0 .Messages Network to Terminal messages Description screen display update data field separator (FS) message coordination number card return/retain flag printer flag (0 .4) printer data group separator (GS) printer flag (0 .4) printer data [2] [2] Code [---] :1C --------[:1D] [---] [---] [:1D] [---] [---] [:1D] [---] [---] :1C [‘4’] [---] :1C [‘E’] [---] [---] [---] [---] [---] [---] [---] [---] [---] No. Network to Terminal messages Messages Description field separator (FS) buffer identifier (F) document enable code group separator (GS) document name track 1 buffer identifier (K) track 1 data track 2 buffer identifier (L) track 2 data field separator (FS) MAC data Code [:1C] [‘F’] [---] [:1D] [---] ’K’ [---] ’L’ [---] [:1C] [---] No. of Characters 1 [3] not supported not supported not supported not supported 1 VAR (max 78) 1 VAR (max 39) 1 [3] 8 [3] [1] If message authentication is used, the three-byte message sequence number is replaced by an eight-byte time variant number, and the optional field separator and MAC data are included in the message. [2] This fields can be repeated up to nine further times. [3] This group of fields (FS/MAC Data) is used only when MAC is configured. The following paragraphs describe the fields in the State Table Load command message. The following paragraphs describe the fields in the Transaction Reply command message. Message identifier field Field size: 1 character Valid range: 4 Description: This one-character data field defines the type of message being transmitted. The only valid value for the Transaction Reply command message is 4. 228 October 2004 U25604-J-Z745-1-7600 Messages Message sequence number Field size: 3 characters Network to Terminal messages Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. It is a reserved entry and contain any three-digit decimal number (000-999). If the terminal uses MACing, this field is replaced by an eight-byte Time Variant Number. See chapter ”Security Features” from page 175 for details. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. If a machine number is entered, this field will contain nine characters with the last six characters of this field being the terminal number. See chapter ”Security Features” from page 175 for additional details. Next state ID data field Field size: 3 characters Valid range: 000-511 Description: This three-character data field contains a decimal number from 000 to 511 in three bytes of graphic code. This field defines the state number which the terminal should execute after the normal completion of the specified Transaction Reply command. Number of bills to dispense Field size: Variable Valid range: See description Description: This field contains the two digit number of bills to dispense for logical cassette type 1 through 4. If the number of bills requested by the host are higher than the cash dispenser is able to dispense in one bundle, the terminal responds with a command reject or a specific command reject. U25604-J-Z745-1-7600 October 2004 229 Network to Terminal messages Transaction serial number Field size: 4 characters Messages Valid range: 0000-9999 Description: The transaction serial number data is four characters of graphic code which identify the transaction to the network. This number originates at the network when a transaction request message is received. The depository printer prints this number on the deposit envelope. Function identifier field Field size: 1 character Valid range: See description Description: The contents of this one-character data field instruct the terminal as to what functions it is to perform. The valid characters are listed as follows: Function ID ’1’ or ‘7’ ’2’ or ‘8’ ’3’ or ‘9’ ‘4’ Short description of the function instructs a deposit + print instructs a dispense + print instructs a display + print instructs a print immediate. A graphic ‘4’ instructs the terminal to print the information sent down-line to the terminal. This function ID is often used when the operator requests to balance the terminal. instructs a set next state + print. A graphic ‘5’ instructs the terminal to print the information sent down-line to the terminal; the terminal proceeds to the next state defined in the Transaction Reply command. This function ID is often used when the consumer requests an inquiry, when a transaction is disallowed, or for any print operation. Night safe deposit and print eject card and dispense and print (card before cash) card before parallel dispense and print instructs a print statement and wait parallel dispense and print and card eject Print statement and next state ‘5’ ‘6’ ‘A’ ‘F’ ‘P’ ‘B’ or ‘C’ ‘Q’ 230 October 2004 U25604-J-Z745-1-7600 Messages Screen number Field size: 3 characters Network to Terminal messages Valid range: 000-999 Description: This field contains three decimal digits of graphic code which represent numbers from 010 to 999. This number indicates one of 989 screens to be displayed on the screen during execution of the Transaction Reply command. This field is used for dispense, deposit and deliver instructions. Screen display update Field size: Variable Valid range: See description Description: This variable-length field contains screen numbers and new screen data which can replace existing screen data. The new screen data can be displayed when this screen number is referenced during transaction processing. The screen update data have the following format: No. of Bytes 3 VAR 1 3 [1] [1] [1] Content screen number screen data group separator screen number screen data VAR [1] These fields are repeated if multiple screens are updated within one reply message. U25604-J-Z745-1-7600 October 2004 231 Network to Terminal messages Message coordination number Field size: 1 character Messages Valid range: ASCII 31-3F (or extended range 31-7E) Description: This is a character assigned by the terminal to each transaction request message. The terminal assigns a different coordination number to each successive transaction request on a rotating basis. The valid range for the coordination numbers is graphic ‘1’ through ‘9’, ‘:’, I ;’, <" =, , ‘>‘, and ‘?’ (ASCII 31 through 3F). If the extended range for the message coordination number field is enabled (Enhanced Configuration Parameters Load message), the valid range is ASCII 31 trough 7E. The host or controller must include the corresponding coordination number when responding with a transaction reply message. If the coordination numbers do not match, the terminal sends a solicited status message with a command reject status. A graphic ‘0’ overrides the message coordination number. As a result, the terminal cannot verify that the transaction authorization corresponds to the last consumer message. Card return/retain flag field Field size: 1 character Valid range: 0-1 Description: This one-character field instructs the terminal to either return or retain the customer’s account card during the close state. The valid values are as follows: ‘0’ - return card ‘1’ - retain card 232 October 2004 U25604-J-Z745-1-7600 Messages Printer flag field Field size: 1 character Network to Terminal messages Valid range: 0-3 Description: This one-character field tells the terminal which printer or printers to use. The valid graphic characters for this field are as follows: ‘0’ - do not print ‘1’ - print on journal printer only ‘2’ - print on customer printer only ‘3’ - print on both printers ‘4’ - print on deposit if function ID is ‘1’ or ‘7’. ’8’ - print on statement printer only Printer data field Field size: Variable (580 characters maximum) Valid range: See description Description: This is a variable-length data field with a maximum of 580 characters. Inserted data is printed by the printer indicated in the printer flag field. Track 3 buffer identifier Field size: 1 character Valid range: ’4’ Description: This one-character track 3 buffer identifier field tells the terminal that track 3 data follows in the buffer data field. Track 3 data Field size: Variable (106 characters maximum) Valid range: See description Description: This field contains the data to be written onto track 3 as instructed by a Transaction Reply command. This data replaces any data previously located in the track 3 buffer of the terminal. The track 3 data consists of up to 106 characters including the start and end sentinels. U25604-J-Z745-1-7600 October 2004 233 Network to Terminal messages Track 1 buffer identifier Field size: 1 character Messages Valid range: ’K’ Description: This one-character buffer identifier field tells the terminal that track 1 data follows in the buffer data field. Track 1 data Field size: Variable (78 characters maximum) Valid range: See description Description: This field contains the data to be written to track 1. This data replaces any data previously located in the track 1 buffer of the terminal. The track 1 data consists of up to 78 characters including the start and end sentinels. Track 2 buffer identifier Field size: 1 character Valid range: ’L’ Description: This one-character buffer identifier field tells the terminal that track 2 data follows in the buffer data field. Track 2 data Field size: Variable (39 characters maximum) Valid range: See description Description: This field contains the data to be written to track 2. This data replaces any data previously located in the track 2 buffer of the terminal. The track 2 data consists of up to 39 characters including the start and end sentinels. MAC data field Field size: 8 characters Valid range: See description Description: This eight-character field contains hexadecimal characters that represent the MAC calculation of the transaction request message. See chapter ”Security Features” from page 175 for additional details. 234 October 2004 U25604-J-Z745-1-7600 Messages Network to Terminal messages Terminal Command message This message is transmitted by the network to startup or shutdown the terminal, or to request a configuration ID. Table 59: “Terminal Command message” on page 236 shows the format of the Terminal Command message. The following paragraphs describe each Terminal Command message type. Startup When the terminal is powered on the first time, all configuration data from the host must be downloaded to the terminal. This requires a startup sequence that loads the ProCash/NDC or ProConsult/NDC frameworks with a predefined configuration from the WIN-NT Registry. In the next step the terminal is ready to receive download commands from the host. The startup command can also put the terminal into service after shutdown or exit from maintenance mode. Shutdown This is an Terminal Command message from the network that places the terminal temporarily out-of-service. All pending messages are sent and current transactions completed, before the terminal executes the shutdown. The terminal then indicates that it has successfully completed the shutdown procedures by sending a ready status in a solicited status message. Configuration information request This Terminal Command message requests the terminal to send a solicited status message containing configuration information. U25604-J-Z745-1-7600 October 2004 235 Network to Terminal messages Messages The following table shows the fields of the Terminal Command message: Table 59: Terminal Command message Description Terminal Command identifier response flag field separator (FS) logical unit number (LUNO) field separator (FS) message sequence number field separator (FS) command code Code ‘1’ [X] :1C [X] :1C [X] :1C --- No. of Characters 1 1 1 3 1 3 1 1 The following paragraphs describe the fields in the Terminal Command message. Message identifier Field size: 1 character Valid range: 1 Description: This one-character data field defines the type of message being transmitted. The only valid value for Terminal Command messages is 1. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. If a machine number is entered, this field will contain nine characters with the last six characters of this field being the terminal number. See section ”Message Authentication (MAC)” on page 199 for additional details. 236 October 2004 U25604-J-Z745-1-7600 this field is replaced by an eight-byte Time Variant Number. It is a reserved entry and contain any three-digit decimal number (000-999). This modifier is the number of the screen to be displayed when the terminal goes out of service. The defined values for the modifier are: ‘0’ . This code includes a modifier. See also section ”Solicited Status (terminal state)” on page 303. The Message sequence number is ignored by ProCash/NDC and ProConsult/NDC.Send Supply Counters. The Send Error Log command asks the terminal to send the error log information for the device groups specified by the Device Identifier. the default out-of-service screen is displayed. If no modifier is included.Messages Message sequence number Field size: 3 characters Network to Terminal messages Valid range: 000-999 Description: The Message Sequence Number field is part of the logical protocol in a network message. ‘2’ .Send Error Log Information. The host requests the Supply counters.Go out-of-service to customers (shutdown). ’5’ . See chapter ”Security Features” from page 175 for details. U25604-J-Z745-1-7600 October 2004 237 . The ATM responds with a Terminal State message (Status Descriptor ‘F’.Send Tally Information (not supported) ‘6’ .Go in service to customers (startup). Message Identifier ‘4’). Command code Field size: 1 character Valid range: See description Description: This one-character field is used to identify the type of command.display Out of Service screen (C02) ‘1’ . The valid values for this field are as follows: ‘1’ .display Temporary Out of Service screen (C06) ‘4’ . Message Identifier ‘2’). See also section ”Solicited Status (terminal state)” on page 303. If the terminal uses MACing. (Status Descriptor ‘F’. The ATM responds with a Terminal State message (Status Descriptor ‘F’. Message Identifier ‘1’).Send Date and Time information (Status Descriptor ‘F’. For command code ’7’ this field is optional. The host requests Configuration ID.Send Configuration Information. and Sensor Status. see section ”Solicited Status (terminal state)” on page 303. Command modifier Field size: 1 character Valid range: See description Description: This field must be present for command code ’6’.Network to Terminal messages Messages ‘7’ . Error Log Information (Command code ’6’) Modifier ’A’ ’B’ ’C’ NOTE: Description Processor and system High order communications SST devices In ProCash/NDC or ProConsult/NDC the solicited status response for modifier ’A’ and ’B’ is the same as for modifier ’C’. Configuration Information (Command code ’7’) Modifier ’1’ ’2’ ’3’ ’4’ ’5’ ’6’ ’7’ Description Send hardware configuration only Send supplies data only Send fitness data only Send tamper and sensor status data only Send software ID and release number data only Send enhanced configuration data Send local configuration option digits 238 October 2004 U25604-J-Z745-1-7600 . Message Identifier ‘5’). ‘8’ . Hardware Status. See also section ”Solicited Status (terminal state)” on page 303. Table 60: State Tables Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration) Modifier (states) Field separator (FS) State number State data Field separator (FS) State number State data Field separator (FS) MAC data Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘2’ [:1C] ----[:1C] [---] [---] [:1C] No. to a maximum of 600 bytes per State Tables Load command message. as necessary.Messages Network to Terminal messages State Tables Load This type of message is used to load state tables to the terminal. The maximum message length for this command is 2000 characters. The following paragraphs describe the fields in the State Tables Load command message. The following paragraphs describe the fields that can be included in the State Tables Load command message. Each message contains a portion of the state tables. of Characters 1 1 1 3 1 3 1 1 1 1 3 25 1 [1] 3 [1] 25 [1] 1 [2] 8 [2] [1] This group of fields (FS/state number/state data) can be repeated. U25604-J-Z745-1-7600 October 2004 239 . [2] This group of fields (FS/MAC Data) is used only when MAC is configured. The only valid value for a download command message is 3. Load command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. If a machine number is entered. It is a reserved entry and contain any three-digit decimal number (000-999).Network to Terminal messages Messages The following paragraphs describe the fields in the State Tables Load command message. 240 October 2004 U25604-J-Z745-1-7600 . Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. this field will contain nine characters with the last six characters of this field being the terminal number. The valid value is ‘1’. The valid value is ‘2’. MAC data field Field size: 8 characters Valid range: See description Description: This eight-character field contains hexadecimal characters that represent the MAC calculation of the transaction request message.Messages Modifier field Field size: 1 character Network to Terminal messages Valid range: 2 Description: This one-character field identifies the configuration data to follow as state table data. state data. and field separator fields can be repeated as required to a maximum of 2000 bytes (total message length). 255-999 Description: This is a three-character field from 000 to 254 and 255-511. The rest of the characters are associated state data. U25604-J-Z745-1-7600 October 2004 241 . State number Field size: 3 characters Valid range: 000-254. State number. State data Field size: Variable Valid range: See description Description: The first entry identifies the state type. See section ”Message Authentication (MAC)” on page 199 for additional details. It identifies the state number for the state data that follows. \LYNXCI\SCREEN”..Network to Terminal messages Messages Screen Data Load This type of message is used to download screen configuration data to the terminal where the data are stored in the WIN-NT registry sub section “. to a maximum of 2000 bytes per Screen Data Load command message. as required. Table 61: Screen Data Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration) Modifier (screens) Field separator (FS) Screen number Screen data Code ‘3’ [X] :1C [X] :1C [X] :1C ’1’ ‘1’ :1C ----- No. of Characters 1 1 1 3 1 3 1 1 1 1[1] 3[1] VAR[1] [1] This group of fields can be repeated. 242 October 2004 U25604-J-Z745-1-7600 . Messages Network to Terminal messages The following paragraphs describe the fields in the Screen Data Load command message. Load Command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. The only valid value for the Screen Data Load command message is 3. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. If a machine number is entered, this field will contain nine characters with the last six characters of this field being the terminal number. See section for additional details. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. It is a reserved entry and contain any three-digit decimal number (000-999). Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. The valid value is ‘1’. U25604-J-Z745-1-7600 October 2004 243 Network to Terminal messages Modifier field Field size: 1 character Messages Valid range: 1 Description: This one-character field identifies the configuration data to follow as screen data. The valid value is ‘1’. Screen number Field size: 3 characters Valid range: 000-999 Description: This is a three-character field that identifies the screen number for the screen data that follows. Screen data Field size: Variable Valid range: See description Description: The variable-length screen data field represents the data to be shown on the screen. This field always follows a screen number entry. Screen numbers, screen data, and field separator fields can be repeated as required to a maximum of 2000 bytes (total message length). 244 October 2004 U25604-J-Z745-1-7600 Messages Network to Terminal messages Configuration Parameters Load The Configuration Parameters Load command message configures terminal parameters, the LUNO and terminal timers. The format of the Configuration Parameters Load message is shown in Table 62: “Configuration Parameters Load” on page 245. This message down-line loads the logical unit number (LUNO), parameters and timers into the WIN-NT Registry. This configuration message should be used first after a power-up because it defines the LUNO and communications timers. The following table contains field definitions of the Configuration Parameters Load command message: Table 62: Configuration Parameters Load Description Load Command Identifier Response Flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration) Modifier (parameters+LUNO+timers) Field separator (FS) Camera control Card reader error threshold Reserved Reserved Track 3 write error threshold Optional parameters Reserved Reserved Reserved Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘3’ :1C X --’000’ ’000’ X --‘000’ ’000’ ’000’ No. of Characters 1 1 1 3 1 3 1 1 1 1 1 (not supported) 3 3 3 3 (not supported) 3 3 3 3 U25604-J-Z745-1-7600 October 2004 245 Network to Terminal messages Messages Description Field separator (FS) Logical unit number (LUNO) Field separator (FS) Timer number Number of ticks Timer number Number of ticks Code :1C [X] :1C ----[---] [---] No. of Characters 1 3 1 2 3 2[1] 3[1] [1] This field can be repeated with the number of timers that are requested to be loaded. The following paragraphs describe the fields in the Configuration Parameters Load message. Load Command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. The only valid value for the Configuration Parameters Load command message is 3. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. If a machine number is entered, this field will contain nine characters with the last six characters of this field being the terminal number. See section ”Message Authentication (MAC)” on page 199 for additional details. 246 October 2004 U25604-J-Z745-1-7600 Messages Message sequence number Field size: 3 characters Network to Terminal messages Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. It is a reserved entry and contain any three-digit decimal number (000-999). Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. The valid value is ‘1’. Modifier field Field size: 1 character Valid range: 3 Description: This one-character field identifies the configuration data to follow as LUNO, parameters and timer data. The valid value is ‘3’. Optional Parameters Field size: 3 characters Valid range: 000-255 Description: The value in the optional parameters field is the sum of the weights of the selected features. Weight ’008’ ’002’ ’001’ Features 12 digit amount buffer size automatic return to previous mode separate ready (’B’) response to transaction reply U25604-J-Z745-1-7600 October 2004 247 Network to Terminal messages Timer number Field size: 2 characters Messages Valid range: 00-20 Description: This two character field contains the timer number. See section ”Timer Data” on page 167 for details on timers. The valid values are as follows: 00 keyboard response time-out interval 01 consumer response extension time-out interval 02 close state screen time-out interval 03 communication message time-out interval 04 envelope insertion time-out interval (depositor) 05 withdrawal time-out interval 06 communications off-line time-out interval 07 withdrawal shutter open time-out interval 08 not used 09 consumer time-out interval before card capture attempt 10 additional cash present time-out interval 11 vandal shield timer 82-83 not used 86 rear settlement time-out interval 87 not used 88-90 reserved 91-93 not used 94 envelope eject time-out interval 95 Statement retract time-out interval 96 Statement present time-out interval 97 vestibule door open time-out interval 98 reserved 99 vandal close timer Number of ticks Field size: 3 characters Valid range: 000-255 Description: This three-character decimal data field determines the time-out intervals for the timers in 800 millisecond ticks. The number of ticks can be 000-255; this gives a time-out range from 0 - 204 seconds. Timer number and number of ticks fields can be repeated as required. Any timers with default values may be, but do not have to be, downline loaded. 248 October 2004 U25604-J-Z745-1-7600 Messages Network to Terminal messages Enhanced Configuration Parameters Load The Enhanced Configuration Parameters Load command message (modifier ’A’) contains additional options and parameters which are not included in the Configuration Parameters Load command message (modifier ’3’). Table 63: Enhanced Configuration Parameters Load Description Load Command Identifier Response Flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration) Modifier (parameters+LUNO+timers) Field separator (FS) Logical unit number (LUNO) Field separator (FS) Option number Option code Option number Option code Field separator (FS) Timer number Number of seconds Timer number Number of seconds Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘A’ :1C --:1C ----[---] [---] :1C ----[---] [---] No. of Characters 1 1 1 3 1 3 1 1 1 1 3 1 2 3 2 3 1 2 3 2[1] 3[1] [1] This field can be repeated with the number of timers that are requested to be loaded. U25604-J-Z745-1-7600 October 2004 249 Network to Terminal messages Messages The following paragraphs describe the fields in the Enhanced Configuration Parameters Load command message. Load Command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. The only valid value for the Enhanced Configuration Parameters Load command message is 3. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. If a machine number is entered, this field will contain nine characters with the last six characters of this field being the terminal number. See section ”Message Authentication (MAC)” on page 199 for additional details. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. It is a reserved entry and contain any three-digit decimal number (000-999). Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. The valid value is ‘1’. 250 October 2004 U25604-J-Z745-1-7600 Messages Modifier field Field size: 1 character Network to Terminal messages Valid range: A Description: This one-character field identifies the configuration data to follow as LUNO, parameters and timer data. The valid value is ‘A’. Logical Unit Number (LUNO) Field size: 3 characters Valid range: 000-999 Description: This three-character field defines the three-character LUNO number. Option number Field size: 2 characters Valid range: 00-99 Description: This two-character field defines the option number of the threecharacter option code. See Table 64 “Option codes” for detailed description of these codes. Table 64: Option codes Option number Option code Description 00 01 000 001 002 008 02 001 002 03 001 002 04 001-040 Camera Control (not supported) Ready/Supply options No options selected (not supported) Separate READY (B) status sent in response to Transaction Reply Auto return to previous mode from supply mode (not supported) 12 digit amount buffer Auto Voice on (default) Auto Voice off Date format for supervisor/journal messages MMDD(YY) DDMM(YY) Roll width. Defines the number of receipt and journal columns used to print messages from the host. (Default is 025) U25604-J-Z745-1-7600 October 2004 251 except in PIN states or/and when ’*’ is pressed Codes reserved for future use Message Coordination Number range. Default is ’008’) Vandal Guard Open Condition 000 001 07 001 002 08 09 10 11 12 000 001 13 14 15 000 001 16-17 18-20 21-22 23 000 001 24-28. This parameter allows to extend the MCN range up to 7E(Hex). 30 31 000 001 32-33 34 000 001 35-49 50-99 001-255 Open vandal guard when card detected (default condition) Open vandal guard when keyboard is enabled Track 1 format ISO format (default condition) VISA format Reserved for future use Diebold status reporting for vandal guard (not supported) Tamper Indicator Control option (not supported) Extended status control (not supported) Specific Command Reject option Do not transmit Specific Command Reject (default condition) Transmit Specific Command Reject Card reader error thresholds (Default value is 010) Track 3 write error thresholds Last Transaction Status information Do not append information (default condition) Append information Not supported by ProCash/NDC Codes reserved for future use Not supported by ProCash/NDC Envelope dispenser status option Do not send unsolicited envelope dispenser messages (default) Send unsolicited envelope dispenser messages Not supported by ProCash/NDC Enable Audio Echo on Keyboard Do not echo the keyboard (default condition) Echo the keyboard.3FH (default condition) 31H .Network to Terminal messages Messages 05 06 001-040 Left print column (Defines the leftmost print column for receipt and journal messages.3F(Hex).7EH Codes reserved for future use Codes reserved for private use 252 October 2004 U25604-J-Z745-1-7600 . 31H . Default range is 31(Hex) . Timer number and number of seconds fields can be repeated as required. Any timers with default values may be. but do not have to be. The valid values are as follows: 00 keyboard response time-out interval 01 consumer response extension time-out interval 02 close state screen time-out interval 03 communication message time-out interval 04 envelope insertion time-out interval (depositor) 05 withdrawal time-out interval 06 communications off-line time-out interval 07 withdrawal shutter open time-out interval 08 not used 09 consumer time-out interval before card capture attempt 10 additional cash present time-out interval 11 vandal shield timer 82-83 not used 86 rear settlement time-out interval 87 not used 88-90 reserved 91-93 not used 94 envelope eject time-out interval 95 Statement retract time-out interval 96 Statement present time-out interval 97 vestibule door open time-out interval 98 reserved 99 vandal close timer Number of seconds Field size: 3 characters Valid range: 000-255 Description: This three-character decimal data field determines the time-out intervals for the timers in seconds. See section ”Timer Data” on page 167 for details on timers. U25604-J-Z745-1-7600 October 2004 253 . The number of seconds can be 000-255. down-line loaded.Messages Timer number Field size: 2 characters Network to Terminal messages Valid range: 00-20 Description: This two character field contains the timer number. The message defines screen data and active keys. This facility allows Central to communicate directly with the keyboard and display in those situations where state table sequencing is inappropiate. Central can establish which accounts are available to the cardholder and build the screen accordingly.Network to Terminal messages Messages Interactive Transaction Response This message may be sent in response to a Transaction Request in order to obtain more information from the cardholder. 10 1 3 1 VAR The following paragraphs describe the fields in the Interactive Transaction Response command message. For example. Key data is returned in a Transaction Request message. the terminal responds with a Transaction Request message containing key data usually in general purpose buffer B. the terminal waits for a consumer response or time-out. a cardholder account selection can be handled in this way. When an FDK or cancel key is pressed or the screen timer expires. 254 October 2004 U25604-J-Z745-1-7600 . Table 65: Interactive Transaction Response Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (ITR) Display flag Active keys Field separator (FS) Screen timer Field separator (FS) Screen data Code ‘3’ [X] :1C [X] :1C [X] :1C ‘2’ ----:1C --:1C --- No. of Characters 1 1 1 3 1 3 1 1 1 6. After the Interactive Transaction Response message. The only valid value for the Interactive Transaction Response command message is 3. The valid value is ‘2’. Load identifier Field size: 1 character Valid range: 2 Description: This one-character data field tells the terminal that screen data of an ITR follows. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. If a machine number is entered. this field will contain nine characters with the last six characters of this field being the terminal number. U25604-J-Z745-1-7600 October 2004 255 . It is a reserved entry and contain any three-digit decimal number (000-999).Messages Load command identifier field Field size: 1 character Network to Terminal messages Valid range: 3 Description: This one-character data field defines the type of message being transmitted. See chapter ”Security Features” from page 175 for additional details. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. while a graphic 1 will activate. Active keys Field size: 6 or 10 characters Valid range: 0-1 Description: This 10-character field either activates or deactivates keyboard keys for consumer responses.display consumer response ‘2’ . the selected key(s) as follows: Character first second third fourth fifth sixth seventh eighth ninth tenth Declaration selects all numeric keys selects FDK ’A’ selects FDK ’B’ selects FDK ’C’ selects FDK ’D’ selects the Cancel key selects FDK ’F’ selects FDK ’G’ selects FDK ’H’ selects FDK ’I’ 256 October 2004 U25604-J-Z745-1-7600 .display Xs as consumer response ‘1’ .Network to Terminal messages Display flag Field size: 1 character Messages Valid range: 0-2 Description: This one-character field instructs the terminal display as follows: ‘0’ .display Xs as consumer response. A graphic 0 will deactivate. (NCR displays ’*’) The keyed response is stored in general purpose buffer B for later transmission in a Transaction Request message. U25604-J-Z745-1-7600 October 2004 257 . Graphic characters represent 001 to 255 800millisecond ticks to give a time-out range from 0.Messages Screen timer Field size: 3 characters Network to Terminal messages Valid range: 000-255 Description: This three-character field determines time-out intervals for the CRT display. Entering 000 gives an infinite display time. Screen data Field size: Variable Valid range: See description Description: This is a variable-length field which represents data to be displayed on the consumer screen.8 to 204 seconds. the last character in general purpose buffer B is “T”. If the terminal "timed out" waiting for the consumer to respond (via keyboard entry) to a screen command. Table 66: FIT Data Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration) Modifier (FIT) Field separator (FS) FIT number FIT data (38 bytes) Field separator (FS) FIT number FIT data (38 bytes) Field separator (FS) MAC data Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘5’ :1C ----[:1C] [---] [---] [:1C] [---] No. 258 October 2004 U25604-J-Z745-1-7600 . of Characters 1 1 1 3 1 3 1 1 1 1 3 114 1 [1] 3 [1] 114 [1] 1 8 [1] This group of fields (FS/FIT number/FIT data) can be repeated. Each message can include up to four tables. as required.Network to Terminal messages Messages FIT Data Load This type of message down-line loads Financial Institution Tables (FIT's) to the terminal. The following paragraphs describe the fields in the FIT Data Load command message. Refer to chapter ”Security Features” from page 175 for details on FIT. One FIT is required for each member financial institution. The terminal can store up to 1000 FIT's. to a maximum of four FIT's per FIT Data Load command message. Table 66: “FIT Data Load” on page 258 illustrates the message format. The following paragraphs describe the message fields. It is a reserved entry and contain any three-digit decimal number (000-999). The only valid value for the FIT Data Load command message is 3. If a machine number is entered. The valid value is ‘1’. U25604-J-Z745-1-7600 October 2004 259 . this field will contain nine characters with the last six characters of this field being the terminal number. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. Modifier field Field size: 1 character Valid range: 5 Description: This one-character field identifies the configuration data to follow as FIT data. See section ”Message Authentication (MAC)” on page 199 for additional details. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal.Messages Load command identifier field Field size: 1 character Network to Terminal messages Valid range: 3 Description: This one-character data field defines the type of message being transmitted. The valid value is ‘5’. FIT is down-line loaded to the terminal. 260 October 2004 U25604-J-Z745-1-7600 . MAC data Field size: 8 characters Valid range: See description Description: This eight-character field contains hexadecimal characters that represent the MAC calculation of the FIT Data Load command message.Network to Terminal messages FIT number Field size: 3 characters Messages Valid range: 000-509 Description: This three-character field designates the number assigned to the FIT in the following field. Refer to section ”Message Authentication (MAC)” on page 199 for additional details. FIT data Field size: 38 bytes Valid range: See description Description: The FIT data specifies control words for processing the PIN. FIT is also used for indirect next state and remote PIN encryption. Table 67: “Encryption Key Load” on page 261 illustrates the message format. the Extended Encryption Key Load message has to be used. For double lengths keys (48 characters).Messages Network to Terminal messages Encryption Key Load The Encryption Key Load message carries encrypted encryption keys to replace the current keys. This message also includes a control word (in the modifier field) that identifies the key in the message and the means of decrypting it (see chapter ”Security Features” from page 175 for a detailed description of data encryption). Table 67: Encryption Key Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Key change Field separator (FS) New key data Code ‘3’ [X] :1C [X] :1C [X] :1C [---] :1C [---] No. The Encryption Key Load message can be used only for single lengths keys (24 characters). of Characters 1 1 1 3 1 3 1 1 1 1 24 Load identifier (encryption key change) ‘3’ U25604-J-Z745-1-7600 October 2004 261 . See section ”Message Authentication (MAC)” on page 199 for additional details. Load identifier Field size: 1 character Valid range: 3 Description: This one-character data field tells the terminal that encryption key data follows. Load command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. The only valid value for the Encrypion Key Load command message is ‘3’. If a machine number is entered. It is a reserved entry and contain any three-digit decimal number (000-999). The valid value is ‘3’.Network to Terminal messages Messages The following paragraphs describe the fields in the Encryption Key Load message. this field will contain nine characters with the last six characters of this field being the terminal number. 262 October 2004 U25604-J-Z745-1-7600 . Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. 6 or 8. this field is not included in the message. The field sizes are as follows: If the key change field is 4 or 7. decrypts and stores new key data inputs for future use. It is eight hex bytes transmitted as eight 3 decimal characters with a range of 000-255. the new key data field is 24 characters.use power-up COMM key (B key) as current COMM key ‘5’ . The valid values for this field are as follows: ‘1’ .use power-up COMM key (B key) as current MAC key ‘8’ . U25604-J-Z745-1-7600 October 2004 263 .send VISA key table to terminal (not supported by Wincor Nixdorf terminals) New key data Field size: Variable Valid range: See description Description: The terminal receives. there is no new key data.decrypt new COMM key with current master key ‘3’ . 5.decrypt MAC key with current COMM key ‘7’ . The size of this field varies. If the key change field is 1. 3.decrypt new COMM key with current COMM key ‘4’ .Messages Key change Field size: 1 character Network to Terminal messages Valid range: 1-9 Description: This one-character field tells the terminal what key(s) to use for encryption and message authentication. 2. depending on the key change field.decrypt MAC key with current master key ‘6’ .decrypt new VISA master key with current VISA master key (not supported by Wincor Nixdorf terminals) ‘9’ .decrypt new master key with current master key ‘2’ . a command reject is issued indicating an Encryption Key Change message of the wrong length has been issued. If this message is sent with a single length key and the terminal is configured to work with double length keys. This message also includes a control word (in the modifier field) that identifies the key in the message and the means of decrypting it (see chapter ”Security Features” from page 175 for a detailed description of data encryption). Double lengths keys usually are used if triple DES verification is enabled. of Characters 1 1 1 3 1 3 1 1 1 1 3 24 or 48 Load identifier (encryption key change) ‘4’ 264 October 2004 U25604-J-Z745-1-7600 . Table 68: Extended Encryption Key Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Key change Field separator (FS) Key data size New key data Code ‘3’ [X] :1C [X] :1C [X] :1C [---] :1C [---] [---] No.Network to Terminal messages Messages Extended Encryption Key Load The Extended Encryption Key Load message allows to carry encrypted encryption keys in double length (48 characters) or single length (24 characters) to replace the current keys. Table 68 “Extended Encryption Key Load” illustrates the message format. If a machine number is entered. The only valid value for the Extended Encrypion Key Load command message is ‘3’. It is a reserved entry and contain any three-digit decimal number (000-999). Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal.Messages Network to Terminal messages The following paragraphs describe the fields in the Extended Encryption Key Load message. Load command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. Load identifier Field size: 1 character Valid range: 4 Description: This one-character data field tells the terminal that encryption key data in single length or double length follows. See section ”Message Authentication (MAC)” on page 199 for additional details. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. this field will contain nine characters with the last six characters of this field being the terminal number. The valid value is ‘4’. U25604-J-Z745-1-7600 October 2004 265 . For a single length key the size is 018 (24 characters). The valid values for this field are as follows: decrypt new master key with current master key decrypt new COMM key with current master key decrypt new COMM key with current COMM key use power-up COMM key (B key) as current COMM key decrypt MAC key with current master key decrypt MAC key with current COMM key use power-up COMM key (B key) as current MAC key decrypt new VISA master key with current VISA master key (not supported by Wincor Nixdorf terminals) ‘9’ .Network to Terminal messages Key change Field size: 1 character Messages Valid range: 1-9 Description: This one-character field tells the terminal what key(s) to use for encryption and message authentication. this field is not included in the message. If the key change field is 1. 6 or 8.send VISA key table to terminal (not supported by Wincor Nixdorf terminals) Key data size Field size: 3 ‘1’ ‘2’ ‘3’ ‘4’ ‘5’ ‘6’ ‘7’ ‘8’ - Valid range: 018 or 030 Description: The key data size specifies the size of the following key data field. 2. New key data Field size: Variable Valid range: See description Description: The terminal receives. there is no new key data. 266 October 2004 U25604-J-Z745-1-7600 . the new key data field is 24 characters for single length keys or 48 characters for double length keys (Triple DES mode). The size of this field varies. It is eight or sixteen hex bytes transmitted where the terminal receives each byte as a 3 digit decimal value in range of 000-255. depending on the key change field. 5. decrypts and stores new key data inputs for future use. The field sizes are as follows: If the key change field is 4 or 7. For a double length key the size is 030 (48 characters). 3. the following fields are repeated with the specified number of Mapping Entries U25604-J-Z745-1-7600 October 2004 267 . Single digit ASCII hex value (range 0-F) Denomination for Cassette. Five-digit ASCII numeric value (e.g. 00010 for $10) :1C ------- ----- 1[1] 5[1] [1] If the Number of Mapping Entries a greater than 01. Table 69 “Dispenser Currency Mapping Table Load” illustrates the message format. which is mapped to the configuration settings in table entry 7 of the Amount Check State defined in the Amount Check State Table. Table 69: Dispenser Currency Mapping Table Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration) Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ No.Messages Network to Terminal messages Dispenser Currency Mapping Table Load This message contains a table that is used to define currency types. of Characters 1 1 1 3 1 3 1 1 1 1 VAR 2[1] 2[1] Modifier (Dispenser Currency Mapping ‘E’ Table) Field separator (FS) Dispenser Currency Mapping Table data Number of Mapping Entries (range 01-FF) Currency Type (range 01-FF) used for mapping to state ’G’ table entry 7 Cassette Type. a solicited error message is generated. If Central transmits a Dispenser Currency mapping Table Load message and it does not conform to the format above. If a specific command reject value is generated then the message content will be ignored. See also section “Amount Check State (G)” on page 84 for detailed configuration description. identifying a specific command reject value for the failure reason (or simply 'A' if specific command reject processing is not activated). or is sent at a time when it is not expected. 268 October 2004 U25604-J-Z745-1-7600 .Network to Terminal messages Messages The Dispenser Currency mapping Table Load is expected at the terminal only when the terminal is in out-of-service mode or supply/supervisor mode. If the configuration data has been changed without the “authorization signature”. The terminal can respond. Thus.e.Messages Network to Terminal messages Configuration ID Load This message contains an identifier for the configuration data sent to the terminal. the configuration ID is set to 0000. At terminal startup. the network sends a configuration ID request terminal command (section ”Terminal Command message” on page 235). the terminal had been powered down and has not been reconfigured. i. or if the encryption keys have been changed. or any time that configuration data is sent to the terminal. When not in one of these conditions. the Configuration ID Load command message acts as an “authorization signature” for the preceding data. the WIN-NT Registry contains the configuration ID number assigned by the Configuration ID Load command message during configuration. as described above to the configuration ID request message only when it is in supply mode or out-of-service mode. After the terminal has received a new configuration ID all downloaded parameters are stored into the WIN-NT Registry. The Configuration ID can be used to verify configuration data. the configuration data in a given terminal. the terminal sends 0000 to the network. U25604-J-Z745-1-7600 October 2004 269 . When properly configured. The terminal responds by sending the configuration ID number to the network. The configuration ID number can be any number from 0000 to 9999. To verify the configuration data. the terminal responds with a command reject (section ”Specific Command Reject Conditions” on page 280). The Configuration ID Load command message must be included as the last of the down-line loaded configuration data to set the configuration ID to the desired number. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. of Characters 1 1 1 3 1 3 1 1 1 1 4 The following paragraphs describe the fields in the Configuration ID Load command message. If a machine number is entered. 270 October 2004 U25604-J-Z745-1-7600 . Load command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. See section ”Message Authentication (MAC)” on page 199 for additional details. this field will contain nine characters with the last six characters of this field being the terminal number.Network to Terminal messages Table 70: Configuration IDLoad Messages Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration data) Modifier (configuration ID number) Field separator (FS) Configuration ID number Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘6’ :1C --- No. The only valid value for the Configuration ID Load command message is 3. It is a reserved entry and contain any three-digit decimal number (000-999). Modifier Field size: 1 character Valid range: 6 Description: This one-character field tells the terminal that the configuration data that follows is the configuration ID. this field is replaced by an eight-byte time variant number. The only valid value is ‘6’. See chapter ”Security Features” from page 175 for details. Configuration ID number Field size: 4 characters Valid range: 0001-9999 Description: This four-character field contains the configuration ID Number. The valid value is ‘1’. U25604-J-Z745-1-7600 October 2004 271 . The configuration ID number must be in the range of 0001 to 9999. If the terminal uses MACing. 0000 indicates that the terminal is not configured.Messages Message sequence number Field size: 3 characters Network to Terminal messages Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. Network to Terminal messages Messages Date And Time Load This message is used to set the date and time in the terminal. Load command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. 272 October 2004 U25604-J-Z745-1-7600 . The only valid value for the Date And Time Load command message is 3. Table 71: Date And Time Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration data) Modifier (configuration ID number) Field separator (FS) Date/Time data Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘C’ :1C VAR No. of Characters 1 1 1 3 1 3 1 1 1 1 10 The following paragraphs describe the fields in the Date And Time Load command message. Modifier Field size: 1 character Valid range: C Description: This one-character field tells the terminal that the configuration data that follows is the configuration ID. U25604-J-Z745-1-7600 October 2004 273 . See section ”Message Authentication (MAC)” on page 199 for additional details.Messages Logical unit number (LUNO) Field size: 3 or 9 characters Network to Terminal messages Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. It is a reserved entry and contain any three-digit decimal number (000-999). The only valid value is ‘C’. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. The valid value is ‘1’. If a machine number is entered. this field will contain nine characters with the last six characters of this field being the terminal number. Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. ‘99’ ‘01’ .‘12’ ‘01’ .‘23’ ‘00’ .‘31’ ‘00’ .‘59’ 274 October 2004 U25604-J-Z745-1-7600 .Network to Terminal messages Date and time data Field size: 10 characters Messages Valid range: See description Description: The date and time specified by the is formatted as follows: „YYMMDDHHMM“. Description YY = Year MM = Month DD = Day HH = Hour MM = Minute Range ‘00’ . The following paragraphs describe the message fields. of Characters 1 1 1 3 1 3 1 1 1 1 37 (only 17 supported) 1 23 (only 17 supported) 1 11 (not supported) 1 4 1 6 1 6 1 11 1 8 U25604-J-Z745-1-7600 October 2004 275 .Messages Network to Terminal messages Message Authentication Field Selection Load This type of message is used to set the messages and fields specified for full or selective MAC verification. Table 72: Message Authentication Field Selection Load Description Load command identifier Response flag Field separator (FS) Logical unit number (LUNO) Field separator (FS) Message sequence number Field separator (FS) Load identifier (configuration data) Modifier (configuration ID number) Field separator (FS) Transaction request field Field separator (FS) Transaction reply field Field separator (FS) Solicited status field Field separator (FS) Other messages field Field separator (FS) Track 1 field Field separator (FS) Track 2 field Field separator (FS) Track 3 field Field separator (FS) MAC data Code ‘3’ [X] :1C [X] :1C [X] :1C ‘1’ ‘B’ :1C VAR :1C VAR :1C --:1C VAR :1C VAR :1C VAR :1C VAR [:1C] [---] No. this field will contain nine characters with the last six characters of this field being the terminal number.Network to Terminal messages Messages The following paragraphs describe the fields in the Message Authentication Field Selection Load command message. The valid value is ‘1’. It is a reserved entry and contain any three-digit decimal number (000-999). See section ”Message Authentication (MAC)” on page 199 for additional details. Logical unit number (LUNO) Field size: 3 or 9 characters Valid range: See description Description: This three-character data field is defined in the configuration data transmitted to the terminal. Load identifier Field size: 1 character Valid range: 1 Description: This one-character data field tells the terminal that configuration data follows. Message sequence number Field size: 3 characters Valid range: 000-999 Description: The message sequence number field is part of the logical protocol in a network message. Load command identifier field Field size: 1 character Valid range: 3 Description: This one-character data field defines the type of message being transmitted. 276 October 2004 U25604-J-Z745-1-7600 . The only valid value for the Message Authentication Field Selection Load command message is 3. If a machine number is entered. The only valid value is ‘B’.Selective MACing Solicited/Unsolicited ID and Message identifier Logical unit number Reserved Time variant number top-of-form flag Message coordination number Track 2 data Track 3 data Operation code data Amount entry field PIN buffer General Purpose Buffer B General Purpose Buffer C Track 1 data buffer identifier Track 1 data Transcation status Data identifier and Last transaction status Transaction reply field Field size: 0-23 (17 supported only) Valid range: 0 or 1 (for each field) Description: The following table shows the fields which can be verified: U25604-J-Z745-1-7600 October 2004 277 . 1 .Messages Modifier Field size: 1 character Network to Terminal messages Valid range: B Description: This one-character field tells the terminal that the configuration data that follows is the configuration ID.MAC complete message. Transaction request field Field size: 0-37 (17 fields supported only) Valid range: 0 or 1 (for each field) Description: The following table shows the fields which can be verified: Field Position Description 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 0 . Terminal State status and Dispenser Currency Mapping Table messages. 278 October 2004 U25604-J-Z745-1-7600 .Selective MACing Transaction Reply command identifier and response flag Logical unit number Message sequence number / Time variant number Next state ID Number of bills to dispense from denomination 1-4 Transaction serial number Function identifier Screen number Screen display update data Message coordination number Card return / retain flag Printer flag field and Printer data Printer flag field and Printer data after the first group separator Printer flag field and Printer data within the next group separators Track 3 buffer identifier Track 3 data field Solicited status field Field size: 11 Valid range: 0 or 1 Description: This field contains the MAC selection data for the solicited status message. ProCash/NDC and ProConsult/NDC always performs a full MAC for solicited status messages. 1 . Other messages field Field size: 4 Valid range: 0 or 1 Description: This field conains the MAC selection data for FIT load. This field is ignored by the application. MAC verification of Terminal State and Dispenser Currency Mapping Table messages are not supported.Network to Terminal messages Messages Field Position Description 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 0 .MAC complete message. State Table load. Ignore bytes 1-10 1 . Offset Description 0 0 . Ignore bytes 1-5 1 .Selectively MAC the fields below 1 Sub field 1 until ’=’ (including start sentinel) 2-5 Sub field 2-5 that should be MACed Track 2 field Field size: 6 Valid range: 0 or 1 Description: This field contains the MAC selection data for Track 2 data.Selectively MAC the fields below 1 Sub field 1 until ’=’ (including start sentinel) 2-5 Sub field 2-5 that should be MACed Track 3 field Field size: 11 Valid range: 0 or 1 Description: This field contains the MAC selection data for Track 3 data.MAC full track.Selectively MAC the fields below 1 Sub field 1 until ’=’ (including start sentinel) 2-10 Sub field 2-10 that should be MACed MAC data field Field size: 8 characters Valid range: See description Description: This eight-character field contains hexadecimal characters that represent the MAC calculation of the Message Authentication Field Selection Load message. See the section ”Message Authentication (MAC)” on page 199 for additional details. Offset Description 0 0 . Description Offset 0 0 .MAC full track. U25604-J-Z745-1-7600 October 2004 279 .MAC full track.Messages Track 1 field Field size: 6 Network to Terminal messages Valid range: 0 or 1 Description: This field contains the MAC selection data for Track 1 data. Ignore bytes 1-5 1 . An illegal function ID is a non supported ID by ProCash/NDC or ProConsult/NDC. An encryption key change message is received before the original key has been entered at the terminal.Network to Terminal messages Messages Specific Command Reject Conditions The terminal will return a specific command reject status if an error is detected in any command sent from the network to the terminal. for example if a screen does not exist the screen number is displayed on the consumer screen 280 October 2004 U25604-J-Z745-1-7600 . The situations which cause a command reject are as follows: q q q q q q q q q q Illegal message class (legal classes are 1. Illegal function ID in Transaction Reply command. 2. and is not ’0’. non existent state number Illegal characters for data convertion received Default display. More than 13 print fields in aTransaction Reply command Date and Time data are invalid in a date and time load command q q q q Default operations include the following: q q q Entry to default close state. 3 or 4) Illegal message sub class Illegal message identifier Illegal terminal command code Illegal terminal command modifier Field separator in illegal position Insufficient fields in the message Insufficient Registry space to store configuration data The dispense amount request is to large The message coordination number in a Transaction Reply message does not match the number in the Transaction Request. For example . An incomplete message is found under the following conditions: – Report logs missing the group number Load of configuration ID incomplete or missing ID field. – Found unexpectedly in the Override Reserved Screen command. – Not found at the end of the coinage field.missing or incomplete data. with expected MAC data missing.incomplete number/value field in configuration message – Truncated MAC field selection load. – Mandatory last field separator not found or found unexpectedly in a Transaction Reply message. Too many print groups in the Transaction Reply message. – Option /timer . More than 13 print groups are present in a Transaction Reply message. – Diebold PIN mode message . 02 Field separator not found or found unexpectedly in the following circumstances: – Found in the middle of an option / timer number and value field in configuration message. 03 04 U25604-J-Z745-1-7600 October 2004 281 . – Not found when skipping the first three field separators in a Transaction Reply message. – Not found in MAC Field Selection Load Data.Messages Network to Terminal messages The following table shows under which conditions the specific command reject value/qualifier combinations are produced: Table 73: Specific Command Reject Conditions Value Qualifier Description A Message format errors 01 Message length error. A group separator is missing or found unexpectedly. 'C' – The terminal command code is 7 and the command modifier is outside the range 0-7. – Coinage field has at least one non-numeric character present.'9' Illegal Terminal Command Code: – Returned if the command code is outside the range '1' .'4' 03 – Message identifier outside the range '1' . 'F'. The following will cause this report: – Message sub-class outside the range '1' . Illegal Load Key Message Identifier.'N' or 'V' or 'Y' or '\' or'[' . 2. Illegal Terminal Command Modifier. – Option/Timer number or value in configuration message. Within a load encryption key data message: – The modifier field is outside the range '1' . Illegal Message Sub-Class or Identifier on a Configuration Load message with class '3' . Message class was not 1.'?'. – Report error log modifier outside the range 'A'' . Within a legal terminal command. Illegal Function ID in Transaction Reply command: – Function ID outside the range 'l'. or message class was 7 and exit support was not detected. 'B'.'9'. 4 or 7.'6' or 'A' -'C'.Network to Terminal messages Messages B 01 Field value errors 02 Illegal Message Class. if a modifier is required: – Report tallies modifier outside the range 'A' . This is found in the following circumstances: – Encryption key change message key data. 'P'. 04 05 06 – The command code is '?' but the modifier is not 0 or 1. 'A'. 'Q'. 07 282 October 2004 U25604-J-Z745-1-7600 . 'C'. 'S' or 'T' Data Field contains non-numeric data. 3. Message type only accepted while terminal Is in In Service mode and is expecting a Transaction Reply. Buffer identifier 'E' missing. Document name error. Illegal Message Type for Current Mode. 09 10 11 13 14 15 16 17 18 C 01 U25604-J-Z745-1-7600 October 2004 283 . The screen identifier in an Override Reserved Screen Command is not in the range 'D0000' to 'D0010'. In a Transaction Reply message.Messages Network to Terminal messages 08 Numeric value out of range. Returned if the Transaction Reply command ID is 'S' (Process Document with Cash) but there is no mandatory field 'ae' in the Transaction Reply message. Illegal FIT number. the co-ordination number is not zero and does not match the transmitted value. – The zone name length in the printer fields of a Transaction Reply message is out of range. Returned if the Transaction Reply contains a buffer identifier not currently supported. The total number of notes requested exceeds the limit of 40 or 20. – In a FIT message. Too many notes in Transaction Reply command. FIT data value is greater than 255 – message contain a value exceeding their maximum values. Total number of coins requested exceeds the limit of 25. Unrecognised buffer identifier. Returned if the data present in a printer field in the Transaction Reply message is shorter than the zone name length given. A FIT in a FIT load message is not in the range of the reserved pool size. Too many coins in Transaction Reply command. The reject is caused by receipt of a Transaction Reply at other times while the terminal is in service. Returned if the document destination (field in the the Transaction Reply) is not one of the allowed values or if the field is null. Invalid Message Co-Ordination Number. Unrecognised document destination. '6'. Message unacceptable in current mode. The following messages cannot be accepted in these modes: – Transaction Replies (not Print Immediate). Message cannot be accepted while in Out-of-Service or Supply modes. – Interactive Transaction Response when not in Transaction Request State. Cannot perform a statement print function while processing a document. not used Cannot process a document while a statement print function is being carried out. It applies to the following messages: – Download messages for customisation. '5'. – Also applies to terminal command when attempting to enable Supervisor 'Dump Images' but terminal is performing a transaction. 04 – Interactive Transaction Response. The key is already in a legal state. Reserved Message not accepted while processing a Transaction Reply.Network to Terminal messages Messages 02 Message cannot be accepted while diagnostics and clear SOH programs for Level 2 and Level 3 are in progress. 03 – Transaction Replies (not Print Immediate). This reply is designed to draw attention to the fact that these programs are being executed. The following messages cannot be accepted while in InService mode: – Terminal commands '4'. 05 06 07 08 09 10 11 12 13 14 Reserved Reserved Reserved Security key initialise message rejected. not used 284 October 2004 U25604-J-Z745-1-7600 . '9'. Reserved Insufficient disk space. due to encryption failure during initialisation. Time of day clock failure during data/time set command or invalid data sent. 02 Not supported by hardware: A dispense function has been issued which requests coins but there is no Coin dispenser present. Reserved Reserved Journal printer backup is inactive 03 04 05 U25604-J-Z745-1-7600 October 2004 285 .Messages Network to Terminal messages D 01 02 03 04 05 06 E 01 Hardware failure Encryption failure during key change message. – VISA PIN verfication key table load via encryption key load message. Reserved Key initialisation command not accepted. Not supported Not supported by software: – The requested function is not supported by current ProCash/NDC or ProConsult/NDC release. – MAC field selection load. Sideways printing on receipt is requested and the option is not available. Network to Terminal messages Figure 5: Transaction Reply message accept/reject flowchart Network sends a Transaction Reply message or host generated screen to the terminal Messages Terminal in Terminal in inservice service mode? mode? No Yes No Terminal in Terminal in transaction transaction request request state? state? Is message Is message a print a print immediate ? immediate ? No Yes Yes Process message Yes Terminal in Terminal in out--of--service out of service mode ? mode ? No Yes Terminal in Terminal in supervisor mode and MISC_PRINT supervisor mode Flag is set to 8 ? No Reject message 286 October 2004 U25604-J-Z745-1-7600 . Messages Terminal operations in Transaction Replies Terminal operations in Transaction Replies This section describes the operation of the terminal in response to Transaction Reply command messages. The following table lists NDC function ID’s and the assignment to the internal ProCash/NDC or ProConsult/NDC step function: Table 74: NDC function ID’s assigned to step functions Function description Print Immediate Set Next State and Print Night Safe Deposit and Print Deposit and Print Dispense. Deliver and Print Display and Print ID ‘4’ ‘5’ ’6’ ’1’ or ’7’ ‘2’ or ‘8’ ‘3’ or ‘9’ Step function DC_F_PRINT_IMMEDIATE DC_F_SET_NEXT_STATE DC_F_NIGHT_SAFE_DEPOSIT DC_F_DEPOSIT DC_F_DISPENSE NDC_F_DISPLAY NDC_F_CBC_DISPENSE Eject Card Dispense and Print ‘A’ (Card Before Cash) Parallel Eject/Dispense and Print (Fast Cash) ‘B’ or ‘C’ NDC_F_PARALLEL_DISPENSE NDC_F_CBC_PARALLEL NDC_F_PRINT_STM_NEXT NDC_F_PRINT_STM_WAIT DC_F_IGNORE Eject Card Dispense and Print ‘F’ Parallel Print Statement and Set Next State ’Q’ Print Data and Stay in Present ’P’ State Ignore Reply Function U25604-J-Z745-1-7600 October 2004 287 . How the terminal responds to each of these function identifiers is the subject of this section. Each Transaction Reply command message identifies a particular function for the terminal to perform. 4. 2. the terminal sends a printer unsolicited status message indicating a fault. Set Next State and Print (‘5’) The terminal handles the Set Next State and Print function ID as follows: 1. 6. 4. Shows the screen specified in the Transaction Reply command message. 3.Terminal operations in Transaction Replies Messages Print Immediate (‘4’) The terminal handles the Print Immediate function ID as follows: 1. If a fault occurs while the printer is printing the terminal sends a printer unsolicited status message indicating a fault. 5. Tells the printer(s) (receipt or journal) defined in the printer flag field of the Transaction Reply command message to print. If a fault occurs while the printer is printing. Initializes for printing. 288 October 2004 U25604-J-Z745-1-7600 . the terminal sends a printer unsolicited status message indicating a fault. If a fault occurs while the printer is printing. Tells the printer(s) (receipt or journal) defined in the printer flag field of the Transaction Reply command message to print. Initializes for printing. Initializes for printing. 3. 2. Tells the printer(s) (receipt or journal) defined in the printer flag field of the Transaction Reply command message to print. Starts the Timer 08 and waits for the deposit to be completed. The deposit is completed when the deposit shutter has been safety closed. Checks for envelope insertion. If Timer 08 does not expire and the cancel key is not pressed while Timer 01 or 08 is active. the terminal sends a deposit solicited status message indicating a fault and waits for a new Transaction Reply command. Deposit and Print (‘1’ or ‘7’) The terminal handles the Deposit and Print function ID as follows: 1. If the envelope should be given in the host replay. the terminal goes to step 3. q q 3. Shows the screen specified in the Transaction Reply command message 2. 3. q If Timer 04 expires before the customer inserts the envelope. q If Timer 08 expires before the deposit is completed. the terminal starts timer 01 (consumer time-out response) and shows screen ’000’. Starts Timer 04 (envelope insertion timer). the screen “please take the envelope” will be displayed. 2. the terminal sends a printer unsolicited message indicating a fault. If Timer 01 expires before the customer inserts the envelope. the terminal starts timer 1 and shows screen ’000’. If the cancel key is pressed while Timers 01 or 08 are active. Shows the screen specified in the Transaction Reply command message. the terminal sends a deposit solicited status message indicating a fault and waits for a new Transaction Reply command. the terminal returns a depository solicited status message indicating a fault and waits for a new Transaction Reply command message. U25604-J-Z745-1-7600 October 2004 289 . Tells the journal and/or receipt printers defined in the printer flag field of the Transaction Reply command message to print. If a fault occurs while the printer is printing. If timer 1 expires before the deposit is completed.Messages Terminal operations in Transaction Replies Night Safe Deposit and Print (‘6’) The terminal handles the Night Safe Deposit and Print function as follows: 1. 4. Tells the printer(s) (receipt or journal) defined in the printer flag field of the Transaction Reply command message to print. the terminal returns a depository solicited status message indicating a fault and waits for a new Transaction Reply command message. q 4. 8. the contents of the amount buffer. q If a fault occurs during transport. the terminal goes to step 5. 12. If a fault does not occur. 5. 290 October 2004 U25604-J-Z745-1-7600 . 9. the terminal checks for an additional function identifier in the Transaction Reply command message. the terminal returns a depository solicited status message indicating a fault and waits for a new Transaction Reply command message. q 6. and the first 20 characters of track 2 data on the envelope. q 10. Initializes for printing. If an envelope is inserted. Transports the deposit envelope. 11. 7. Prints the transaction serial number. Increases the deposit envelope count by one. If a fault does not occur. Waits for the deposit to finish. q If a fault occurs while the terminal is waiting for the deposit to finish.Terminal operations in Transaction Replies q Messages If the cancel key is pressed while the terminal is checking for the insertion of the envelope. the terminal goes to step 7. Initializes for envelope entry. the terminal returns a depository solicited status message indicating a fault and waits for a new Transaction Reply command message. If a fault occurs while the printer is printing the terminal returns a printer unsolicited status message indicating a fault. Initializes for finishing the deposit. the terminal waits for printing to finish and then checks for an additional function identifier in the Transaction Reply command message. 7. 4. Waits for a new Transaction Reply command message. Wincor Nixdorf retract able terminals proceeds as follows: q q Starts Timer 10 (doorless terminal withdrawal time-out interval). Starts dispensing. 3. Informs the printer(s) (receipt or journal) defined in the printer flag field of the Transaction Reply command message to print. Turns on the beeper. U25604-J-Z745-1-7600 October 2004 291 . Turns on the beeper. Shows the screen specified in the Transaction Reply command message. 2. Deliver and Print (‘2’ or ‘8’) The terminal handles the Dispense. Initializes for the dispense function. Informs the printer(s) (receipt or journal) defined in the printer flag field of the Transaction Reply command message to print. the terminal proceeds as follows: q q Returns a printer unsolicited status message indicating a fault. 3.Messages Terminal operations in Transaction Replies Dispense. Waits for a new Transaction Reply command message. If a fault does not occur while the printer is printing. 2. 8. the terminal proceeds as follows. q q Returns a dispenser solicited status message indicating a fault . After the screen is displayed the terminal does the following: q q Starts Timer 10 (withdrawal time-out interval). Deliver and Print function ID as follows: 1. Display and Print (‘3’ or ‘9’) The terminal handles the Display and Print function ID as follows: 1. If a fault occurs during dispense. 5. If a fault occurs while either printer is printing. 6. Shows the screen specified in the Transaction Reply command message. Timer 02 is in use to determine the length of time that the Close screen is displayed. For retract terminals Timer 05 is started the cash has been dispensed. If the notes are taken within the time frame of Timer 05 the timer is canceled. Also the beeper is active during Timer 05 is running. the dispensed money will be rejected and the terminal enters the next state specified in the Transaction Reply. If the notes have not been taken when the timer expires. and the next state is entered on expiry. Cut and deliver receipt if necessary. card will be retained. 2. Waits for a new Transaction Reply command message. the terminal waits for printing to finish and then checks for an additional function identifier in the Transaction Reply command message. Prints the receipt and journal data. If a fault occurs while the printer is printing. cash will be delivered and the screen „Please wait for Cash and receipt“ is shown. Dispense and Print function ID as follows: 1. 4. 292 October 2004 U25604-J-Z745-1-7600 . If card was taken. If a fault does not occur while the printer is printing. Eject Card.Terminal operations in Transaction Replies Messages 4. the terminal proceeds as follows: q q Sends a printer unsolicited status message indicating a fault. If card was not taken. Timer 07 is started. 5. Dispense the money and ejects the card. 6. Dispense and Print (‘A’) (Card before Cash) The terminal handles the Eject Card. Shows the „Take receipt and Cash“ or „Take Cash“ screen as long as Timer 02 is active. the message „Cash retracted“ is logged to the journal and an unsolicited error is reported to the host. 5. If some notes are retracted. 3. a retract is attempted. Shows the “Please take your card“ screen specified in the Transaction Reply command message as long as the customer takes the card or it will be captured after the Timer 09 has expired. In both cases. U25604-J-Z745-1-7600 October 2004 293 . If card was not taken. Timer 02 is in use to determine the length of time that the Close screen is displayed. Dispense and Print function ID (Card before Cash) as follows: 1. Prints the receipt and journal data. For retract terminals Timer 05 is started the cash has been dispensed. 2.Messages Terminal operations in Transaction Replies Eject Card. If the notes have not been taken when the timer expires. the dispensed money will be rejected and the terminal enters the next state specified in the Transaction Reply. a retract is attempted. If some notes are retracted. 6. Shows the ‘Please take your card“ screen specified in the Transaction Reply command message as long as the customer takes the card or it will be captured after the Timer 09 has expired. Ejects the card. In both cases. the message „Cash retracted“ is logged to the journal and an unsolicited error is reported to the host. Also the beeper is active during Timer 05 is running. If the notes are taken within the time frame of Timer 05 the timer is canceled. If card was taken. Cut and deliver receipt if necessary. Dispense and Print (‘F’) (Parallel CBC) The terminal handles the Parallel Eject Card. Timer 07 is started. and the next state is entered on expiry. 3. Shows the „Take receipt and Cash“ or „Take Cash“ screen as long as Timer 02 is active. 5. card will be retained. 4. dispense the cash and shows the screen „Please wait for Cash and receipt“. This can be repeated until the network sends a new function reply containing a next state. For retract terminals Timer 05 and Timer 07 is started the cash has been dispensed. Retains the card if the terminal cannot advance the card to write on it. 2. If the notes have not been taken when the timer expires. This allows the terminal to print large amounts of data without continually sending request messages to the network. 4. the terminal sends a READY to the network.Terminal operations in Transaction Replies Messages Parallel Eject/Dispense and Print (Fast Cash) (‘B’ or ‘C’) The terminal handles the Parallel Eject/Dispense and Print function ID as follows: 1. Displays the screen „. Parallel Eject/Dispense and Print. the message „Cash retracted“ is logged to the journal and an unsolicited error is reported to the host. the terminal goes to step 5. Wait for card to be taken or captured. 3. a retract is attempted. If the notes are taken within the time frame of Timer 05 and Timer 07 the timer is cancelled. Timer 02 is in use to determine the length of time that the Close screen is displayed. Cut and deliver receipt if necessary and shows the screen „Take Card and Cash“. 5. If some notes are retracted.. Also the beeper is active during Timer 05 is running. Returns a card writer solicited status message indicating a fault and waits for a new Transaction Reply command message Print Data and Stay in Present State (‘P’) The Print Data and Stay in Present Mode function tells the terminal to print data and stay in present state. After printing has been finished. if not already taken.and receipt“ specified in the close state. Then the network sends the next part of the printer data.. q If a fault does occur after five attempts to write to the card. Shows the ‘Please wait“ screen specified in the transaction request state. 294 October 2004 U25604-J-Z745-1-7600 . Depending on the print flag logging data are printed on journal..Messages Electronic Journal Upload (EJU) commands Print Statement and Set Next State (‘Q’) The Print Statement and Set Next State function is used to print statement data on receipts. If the printing has been finished. Electronic Journal Upload (EJU) commands This section describes the commands that will be sent by the host to enable. Then the terminal displays the transaction reply screen (Take Statement).. During printing on receipt the terminal displays the transaction request screen (Please Wait). continue und stop Electronic Journal Upload (EJU). U25604-J-Z745-1-7600 October 2004 295 . the terminal sends a READY to the network. EJU consists of following three terminal commands: q q q Send Options And Timers Acknowledge And Continue Acknowledge And Stop see description of the commands on the following pages . Message Identifier Field size: 1 character Valid range: 6 Description: This field specifies the message identifier. The following table describes the message format and its fields: Table 75: Send Options And Timers message format Description Message Identifier Field Separator (FS) Field Separator (FS) Field Separator (FS) Command Type Option Number Block Size Option Value Block Size Option Number Retry Threshold Option Value Retry Threshold Field Separator (FS) Acknowledge Timer Number AcknowledgeTimer Value Mandatory Optional M M M M M O O O O M O O Code 6 :1C :1C :1C 3 60 VAR 61 VAR :1C 60 VAR No. 296 October 2004 U25604-J-Z745-1-7600 . The message identifier for Electronic Journal is 6. the 3 digit Option Value has to follow after each option. See also ProCash/NDC ProConsult/NDC Installation manual for EJU configuration.Electronic Journal Upload (EJU) commands Messages Send Options And Timers This command can be sent at any time to enable the Electronic Journal Upload. of Characters 1 1 1 1 1 2[1] 3[1] 2[1] 3[1] 1 2 3 [1] If one or both Option Number(s) (60 or/and 61) are inserted. Messages Command Type Field size: 1 character Electronic Journal Upload (EJU) commands Valid range: 3 Description: This field specifies the command type for message identifier 6. Option Value Retry Threshold Field size: 3 characters Valid range: 000-999. The send attempt will be marked as successfull as soon as the terminal has received an Acknowledge command. default is 200 Description: This field specifies the option value for the maximum size of electronic journal data that has to be sent to the host. The command type for Send Options and Timers is 3. U25604-J-Z745-1-7600 October 2004 297 . Option Number Retry Threshold Field size: 2 characters Valid range: 61 Description: This field specifies the option number indicating the retry threshold following the three digit Option Value Retry Threshold. Option Value Block Size Field size: 3 characters Valid range: 010-350. Option Number Block Size Field size: 2 characters Valid range: 60 Description: This field specifies the option number indicating the block size following the three digit Option Value Block Size. default is 000 (infinite retries) Description: This field specifies the option value for the number attempts to successfully send an Electronic Journal Upload block. 298 October 2004 U25604-J-Z745-1-7600 . default is 000 (infinite) Description: This field specifies the Acknowledge Timer Value for the timer that indicates the maximum time in seconds to wait for an acknowledgement message from host before the same block will be resent. Acknowledge Timer Value Field size: 3 characters Valid range: 000-255.Electronic Journal Upload (EJU) commands Acknowledge Timer Number Field size: 2 characters Messages Valid range: 60 Description: This field indicates the Acknowledge Timer Number with the following Acknowledge Timer Value. Command Type Field size: 1 character Valid range: 1 Description: This field specifies the command type for the Acknowledge And Continue of message identifier 6. the contents of the shared mapping where all EJ data are stored will be erased. The message identifier for Electronic Journal is 6. the terminal will send the same block again. If the terminal has received the acknowledgement for the last electronic journal data block. Then the default option and timer values will be used. of Characters 1 1 1 1 1 6 Valid range: 6 Description: This field specifies the message identifier. The following table describes the Acknowledge And Continue message format and its fields: Table 76: Acknowledge And Continue Description Message Identifier Field Separator (FS) Field Separator (FS) Field Separator (FS) Command Type Last Character Received Message Identifier Field size: 1 character Mandatory Optional M M M M M O Code 6 :1C :1C :1C 1 VAR No. If after sending an EJ block to the host. the terminal does not receive an acknowledgement within the specified time.Messages Electronic Journal Upload (EJU) commands Acknowledge And Continue This command should be sent by the host each time a block of electronic journal data is received from the terminal. It can also be sent unsolicited at any time to enable EJU instead of sending the Options And Timers command. U25604-J-Z745-1-7600 October 2004 299 . See also ProCash/NDC ProConsult/NDC Installation manual for EJU configuration. 000 character count which starts at zero when the application will be started and EJU has been activated. 300 October 2004 U25604-J-Z745-1-7600 . The last Char Previous Block and Last Char This Block values are based on a modulus 1.000. If the value is different. the terminal will not count this message as an acknowledgement.Electronic Journal Upload (EJU) commands Last Character Received Field size: 6 characters Messages Valid range: 000000-999999 Description: The value in this field should be the same as the value in the Last Character This Block field in the last EJU data message sent by the terminal. U25604-J-Z745-1-7600 October 2004 301 . Command Type Field size: 1 character Valid range: 2 Description: This field specifies the command type for the Acknowledge And Stop of message identifier 6. See also ProCash/NDC ProConsult/NDC Installation manual for EJU configuration. of Characters 1 1 1 1 1 6 Valid range: 6 Description: This field specifies the message identifier. The message identifier for Electronic Journal is 6.Messages Electronic Journal Upload (EJU) commands Acknowledge And Stop This command acknowledges the last EJU block received by the host. and in addition indicates that EJU has to be stopped. The following table describes the Acknowledge And Stop message format and its fields: Table 77: Acknowledge And Stop Description Message Identifier Field Separator (FS) Field Separator (FS) Field Separator (FS) Command Type Last Character Received Message Identifier Field size: 1 character Mandatory Optional M M M M M M Code 6 :1C :1C :1C 2 VAR No. This will disable the EJU function until the host sends a new Acknowledge And Continue command or Options And Timers command. 000 character count which starts at zero when the application will be started and EJU has been activated.Electronic Journal Upload (EJU) commands Last Character Received Field size: 6 characters Messages Valid range: 000000-999999 Description: The value in this field should be the same as the value in the Last Character This Block field in the last EJU data message sent by the terminal. The last Char Previous Block and Last Char This Block values are based on a modulus 1.000. 302 October 2004 U25604-J-Z745-1-7600 . the status information will vary according to which of the following terminal commands has been received by the terminal. Terminal Command Send Configuration Information Send Supply Counters Send Error Log Information Send Date/Time Information Send Configuration ID Hardware Configuration Data Supplies Data Fitness Data Tamper and Sensor Status Data Software ID and Release Number Local Configuration Option Digits Message Identifier 1 2 4 5 6 H I J K L M U25604-J-Z745-1-7600 October 2004 303 .Messages NDC Status Messages NDC Status Messages Solicited Status (terminal state) If the status descriptor field contains an ‘F’ in the solicited status message. 304 October 2004 U25604-J-Z745-1-7600 . of Characters 1 4 1 22 or 38 1 44 or 76 1 23 or 26 1 12 1 6 1 9 Valid range: 1 Description: This message is sent to central in response to a send configuration information terminal command message.NDC Status Messages Send Configuration Information Messages This solicited status message is sent to central in response to a Send Configuration Information terminal command message. Configuration ID Field size: 4 Valid range: 0000-9999 Description: Contains the last four digit configuration ID numbers sent to the terminal from host. Table 78: Send Configuration Information Description message identifier configuration ID field separator (FS) hardware fitness field separator (FS) hardware configuration field separator (FS) supply status field separator (FS) sensor status field separator (FS) NDC+ release number field separator (FS) NDC+ software ID Message identifier Field size: 1 Code ‘1’ --:1C --:1C --:1C --:1C --:1C --:1C --- No. Messages Hardware Fitness Field size: 22 or 38 NDC Status Messages Valid range: 0-4 Description: Contains one byte per device or major device resource. The following table gives an overview about the devices of the hardware fitness: Table 79: Hardware Fitness Table Field 0 1 2 3 4 5 6 7 8 9 10 Contents time of day clock high order communications system disk card reader cash handler depository receipt printer journal printer reserved reserved night safe depository Field 11 12 13 14 15 16 17 18 19-20 21 Contents encryptor security camera door access flex disk cassette type 1 cassette type 2 cassette type 3 cassette type 4 reserved statement printer U25604-J-Z745-1-7600 October 2004 305 . Each byte is encoded with an error severity value indicating the current fitness of the device. warning and fatal conditions can only be cleared by local supervisor transactions or through an system reboot for some devices if the reboot flag is set. The following table describes the meaning of the severity codes: Code 0 1 2 3 4 Severity no error routine errors have occurred warning conditions have occurred suspend. terminal is currently in suspend state due to suspected tampering with this device fatal error condition exists Routine. Each byte is encoded with an error severity value indicating the current fitness of the device. 306 October 2004 U25604-J-Z745-1-7600 . Table 81: “Device Configuration Table” on page 307 mainly contains expressions of NCR specific hardware.PPF. to send the expected values for the host in the Hardware Configuration Information message. See Table 81: “Device Configuration Table” on page 307 for the definition of ech byte. For ProCash/NDC and ProConsult/NDC this table is just a reference table where the option bits of each hardware device can be taken and be set in section [HARDWARE_CONFIGURATION] of configuration file CUSTOM.NDC Status Messages Messages The following table lists devices that are additionally appended in the Hardware Configuration Status message if command modifier ’6’ for command code ’7’ is used: Table 80: Hardware Fitness Table Enhanced Field 22 23 24 25 26 27 28 29 30 Contents Signage Display Reserved Coin Dispenser System Display Media Entry Indicators Envelope Dispenser Document Processing Module Coin Dispensing Module Tamper Indication Document Processing Module Tamper Indication Module Field 31 32 33 34 35 36 37 Contents Reserved Digital Audio Service Reserved Reserved Reserved Reserved Reserved Hardware configuration Field size: 44 or 76 Valid range: see detailed value description Description: Contains one byte per device or major device resource. Messages NDC Status Messages Table 81: Device Configuration Table Byte Device 0 Product 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1E 1F Description Class 5663 5674 5675 5684 5685 5688 5665 5670 personaS75 personaS88 personaS40 personaS70 personaS74 personaS84 personaS85 5305 5886 1 2 7F System Disk 00 02 Magnetic Card Reader/Writer 01 03 05 07 08 09 0A 0B 0C 10 11 1D Cash Handler 00 01 02 Depository 00 01 02 03 04 No Configuration Hard Disk present Reserved Track 2 (read only) Track 1/2/3 MCRW (write track3 only) Low cost DIP reader 3 Track Write MCRW Track 2 Smart Card Reader Track 1/2/3 Smart Card Reader 3 Track Write Smart Card Reader Track 2/3 DIP MSR Track 1/2/3 CIM 86 MCRW Track 1/2 DIP MSR Track 1/2 Swipe Card DIP Reader MIMIC Smart Card DIPReader Standard cash handler not configured Standard cash handler configured Angel spray dispenser configured Not configured Reserved PPD Reserved (third generation ADM) DPM envelope depository (non-5665 SSTs only) 3 4 5 U25604-J-Z745-1-7600 October 2004 307 . NDC Status Messages Messages 6 Receipt Printer 00 01 02 03 04 05 06 07 08 Journal Printer 00 01 02 03 80 81 82 83 Reserved 00 01 Reserved 00 01 Night Safe Depository 00 01 02 Encryptor ?0 ?1 02 03 04 ?5 06 Not configured Plain paper Black dot paper (TOF) Sideways printing. D/A) Reserved Digital Not configured Configured 13 308 October 2004 U25604-J-Z745-1-7600 . 3M) Variable format (for instance.sideways printing. no black mark Thermal printer .sideways printing. no black mark Sideways printing. black mark Not configured Integral journal printer Reserved Thermal printer Electronic journal Electronic journal and integral journal printer Reserved Electronic journal and thermal printer Not configured Configured Not configured Configured Not configured Configured Reserved Not configured NBS encyptor Reserved Reserved Reserved EKC encryptor Reserved ? = SST key entry mode (0. or C) where: 0 = single length keys without XOR key entry B = single length keys using XOR key entry C = double length keys 7 8 9 10 11 12 Security Camera 00 01 02 03 04 Door Access 00 01 Not configured Fixed format (for instance. B.no black mark Thermal printer .black mark Thermal printer . black mark Thermal printer . secure PPD Secure cash. insecure cards.Voice not supported 1 .(always) 0 .(always) 0 .Standard FDK’s 1 .VGA 1 .VGM Translator 0 .Voice supported if digital audio present 0 .88 MB flex disk connected No TI bins present Secure cash. and PPD or no PPD Reserved Standard (BAPE) Keyboard EKC Keyboard Not configured Standard keyboard (Basic) Keyboard plus FDK’s (Enhanced) 0 .Touch screen 0 . insecure cards.(always) 0 .44 MB flex disk connected 2.(always) No configuration No configuration Not configured Configured Reserved Reserved 5665 DPM statement printer Enhanced thermal statement printer (SDC+) Not configured Configured Reserved None RMX S4 Not configured 20 x 40 Display Enhanced Display (16 x 32) 15 16 17 18 19 20 21 7F 7F Statement printer 00 01 02 03 05 09 Signage Display [1] 00 01 22 23 24 --Coin Dispenser [1] 00 01 02 System Display [1] 00 01 02 25 U25604-J-Z745-1-7600 October 2004 309 . Bins not DPM or CDM 00 01 02 03 Cardholder Keyboard 00 01 02 Operator Keyboard 00 01 02 Cardholder Display / Voice BIT 0 BIT 1 BIT 2 BIT 2 BIT 3 BIT 3 BIT 4 BIT 4 BIT 5 BIT 6 BIT 7 Not configured 1.Messages NDC Status Messages 14 Flex Disk 00 01 02 Tamper Indicat. PPD or no PPD Secure cash. cards.(always) 0 . [1] [1] These devices are only appended in the message if command modifier ’6’ is used.NDC Status Messages Messages 26 Media Entry Indicators [1] 00 01 Envelope Dispenser [1] 00 01 02 03 Document Processing Module [1] 00 01 02 Coin Dispensing Module Tamper Indication [1] 00 01 Document Processing Module Tamper Indication [1] 00 01 Not configured Configured Not configured Configured Reserved Reserved Not configured 5665 DPM configured DP-ATM configured 27 28 29 Not configured Present 30 Not configured Present Reserved 31 32 --Digital Audio Service 00 01 [1] Not configured Present Reserved 33-37 --. 310 October 2004 U25604-J-Z745-1-7600 . U25604-J-Z745-1-7600 October 2004 311 .Not Configured 1 . See section ”Sensor Status (unsolicited) (DID ‘P’)” on page 361 for details.14 15 16 17 18 19-20 21 22 23 24 25 Contents not used = 0 cassette type 1 cassette type 2 cassette type 3 cassette type 4 not used = 0 statement printer statement ribbon reserved [1] reserved [1] envelope dispenser [1] These devices are only appended in the message if command modifier ’6’ is used. Sensor Status Field size: 12 Valid range: see description Description: Contains one character per sensor and is identical to the information reported in character 2-13 of the Sensors status message.Good State 2 .Media Out 4 .Overfilled Description: Contains one byte of following devices: Table 82: Supply Status Device Table Field 0 1 2 3 4 5 6 7 8 9 10 [1] Contents reserved reserved not used = 0 card capture bin cash handler reject bin deposit bin receipt paper journal paper not used = 0 not used = 0 night safe depository Field 11 .Messages Supply Status Field size: 23 or 26 NDC Status Messages Valid range: 0 .Media Low 3 . 04. The second pair of digits represents the point release number. Following values are valid: G530-0205 (NDC+ Native mode) G530-0206 (NDC+ Diebold Emulation mode) ProCash/NDC reports G530-0205 (NDC+ Native mode) 312 October 2004 U25604-J-Z745-1-7600 . Example: 060400 is release 06. The third pair of digits represents the patch release number.NDC Status Messages NDC+ Release Number Field size: 6 Messages Valid range: see description Description: Contains a six digit decimal number. The first pair of digits represents the release number.00 NDC+ Software ID Field size: 9 Valid range: see description Description: Contains the NDC+ Software ID. the transaction has not been initiated and terminal counters have not been updated.Messages Send Supply Counters NDC Status Messages This solicited status message is sent to the host in response to a “Send Supply Counters” terminal command message. of Characters 1 4 7 20 20 20 20 5 5 5 (not supported) 5 Valid range: 2 Description: This message is sent to the host in response to a Send Configuration Information terminal command message. Transaction serial number Field size: 4 Valid range: 0000-9999 Description: Contains the TSN of the last transaction processed by the terminal. Table 83: Supply Counters Description message identifier transaction serial number accumulated transaction count notes in cassette notes rejected notes dispensed last transaction notes dispensed cards captured envelopes deposited camera film remaining last envelope serial number Message identifier Field size: 1 Code ‘2’ --------------------- No. If this does not correspond to the last TSN sent by host. U25604-J-Z745-1-7600 October 2004 313 . or the non-volatile terminal memory was last corrupted. 3 and 4. 2. 65535 Description: Consists of four 5 digit decimal counts of the total number of notes remaining in cassette types 1. The counts are set by supervisor functions and are decremented on each dispense transaction. ProCash/NDC sets this counter to value 65535 if the dispense below zero option is enabled. If physically more notes are dispensed (dispense below zero) than initially set (number of notes loaded) via one of the SOP function. Notes dispensed Field size: 20 Valid range: 00000-99999 Description: Consists of four 5 digit decimal counts of the total number of notes dispensed from cassettes 1. 2. Notes in cassette Field size: 20 Valid range: 00000-09999.999.999 transactions. the sum of these counters for a particular cassette does accurately represent the difference between the original number of notes added and the number of notes dispensed. These counts are zero if not set by the „Standard Cassette Change“ or „Set Cassette Counters“ SOP function. 3 and 4. 3 and 4. 2. The count is reset to 0 after 9.NDC Status Messages Accumulated transaction count Field size: 7 Messages Valid range: 0000000-9999999 Description: Defines the total number of transactions completed since the terminal was installed. 314 October 2004 U25604-J-Z745-1-7600 . Although the fields ‘Notes in Cassettes’ and ‘Notes rejected’ may not be totally accurate. These counts are consistent with note counts reported since the counts were last cleared by a SOP function. Notes rejected Field size: 20 Valid range: 00000-99999 Description: Consists of four 5 digit decimal counts of the total number of notes moved to the reject bin from cassettes 1. Messages Last transaction notes dispensed Field size: 20 NDC Status Messages Valid range: 00000-99999 Description: Consists of four 5 digit decimal counts of the total number of notes dispensed on the last transaction processed by the terminal. Last envelope serial number Field size: 5 Valid range: 00000 Description: The last envelope serial number is always set to 00000. U25604-J-Z745-1-7600 October 2004 315 . The count includes cards captured up to and including the transaction defined in the transaction serial number. Envelopes deposited Field size: 5 Valid range: 00000-99999 Description: Consists of one 5 digit decimal count of the number of envelopes deposited since the count was last cleared by a SOP function. Camera film remaining Field size: 5 Valid range: 00000 Description: Not supported by Wincor Nixdorf terminals. These field allows the host to recover note counts after power failure. even if the power failure occurred in the middle of a dispense operation. The count includes envelopes deposited up to and including the transaction defined in the transaction serial number. Card captured Field size: 5 Valid range: 00000-99999 Description: Consists of one 5 digit decimal count of the number of cards captured since the count was cleared by a SOP function. Always returned as zeros. The following log entry contains the information which has been repeatedly logged by the system. In case of a repeated log there are two entries. Message identifier Field size: 1 Valid range: 4 Description: This message is sent to central in response to a send error log group terminal command message. of Characters 1 1 2 12 2 [1] 2 [1] 2 [1] 2 [1] 1 [1] 2 [1] 1 [1] 1 [1] 23 [1] 1 [1] [1] These fields are repeated for each log entry present. with the time of the first entry. The first acts as a header indicating the time of the most recent entry and the number of times repeated. the terminal reads the contents from the CMOS and send it to the network.NDC Status Messages Send Error Log Information Messages This solicited status message is sent to the host in response to a “Send Error Log Information” terminal command message.BIN”. All error log information are stored in the CMOS file “C:\PROTOPAS\WORK\CCCMOS. Table 84: Send Error Log Information Description message identifier group number new entries date last cleared month day hour minute device identification (DID) maintenance status (M-Status) severity part number maintenance data (M-Data) field separator Code ‘4’ C --------------------VAR :1C No. If the error log information request (6C) is sent from the host. The error log file can be cleared via the User Exit function. The field separator is not present after the last log entry. Enter “Individual Functions” from the main menu and select “Clear Error Log”. 316 October 2004 U25604-J-Z745-1-7600 . ‘A’ = Processor system (not supported by Wincor Nixdorf terminals) ‘B’ = Communications (not supported by Wincor Nixdorf terminals) ‘C’ = ATM devices New entries Field size: 2 Valid range: See description Description: The number of new entries on the log since last read.Messages Group number Field size: 1 NDC Status Messages Valid range: C Description: This field indicates the group number of the requested group. If this is greater than log entries reported it indicates that log entries have been missed. Date last cleared Field size: 12 Valid range: See description Description: The date and time the log was last cleared in the following format: YY = Year MM = Month DD = Day HH = Hour MM = Minute SS = Second Month Field size: 2 00-99 01-12 01-31 00-23 00-59 00-59 Valid range: 01-12 Description: Month log entry U25604-J-Z745-1-7600 October 2004 317 . Repeat log 318 October 2004 U25604-J-Z745-1-7600 .NDC Status Messages Day Field size: 2 Messages Valid range: 01-31 Description: Day log entry Hour Field size: 2 Valid range: 00-23 Description: Hour log entry Minute Field size: 2 Valid range: 00-59 Description: Minute log entry Device identification Field size: 1 Valid range: ‘C’ Description: This field identifies the device for which the log entry was made.ATM device log . ‘A’ ‘B’ ‘C’ ‘?’ Processor system (not supported by Wincor Nixdorf terminals) Communications (not supported by Wincor Nixdorf terminals) or greater. This is the device identification used in all Wincor Nixdorf terminals reporting. U25604-J-Z745-1-7600 October 2004 319 . Each pair of characters represents the binary value of a single byte of detailed maintenance data. Maintenance data (M-data) Field size: 2 Valid range: 0-9.Messages Maintenance status (M-status) Field size: 2 NDC Status Messages Valid range: 00-99 Description: For a repeat log entry (’?’) this is field contains the number of times the log entry is repeated. Severity Field size: 1 Valid range: 1-4 Description: Severity of the log entry. For a repeat log entry this data field is empty. A-F Description: Maintenance data consisting of a string of hexadecimal characters. Part number Field size: 1 Valid range: always zero Description: Part number of the component of the device. Table 85: Send Date/Time Info Description message identifier TOD clock status terminal date/time Message identifier Field size: 1 Code ‘5’ 0-2 --- No. TOD clock status Field size: 1 Valid range: 0-2 Description: 0 = Time is actual. of Characters 1 1 12 Valid range: 5 Description:This message is sent to central in response to a send date and time information terminal command message. 1 = Time is default. 2 = TOD malfunction Terminal date/time Field size: 12 Valid range: See description Description: The actual date and time returned by the terminal clock in format: YY = Year MM = Month DD = Day HH = Hour MM = Minute SS = Second 00-99 01-12 01-31 00-23 00-59 00-59 320 October 2004 U25604-J-Z745-1-7600 .NDC Status Messages Send date/time information Messages This solicited status message is sent to the host in response to a send date and time terminal command message. U25604-J-Z745-1-7600 October 2004 321 . are repeated for each of the devices present in the ATM. Table 86: Hardware Configuration Data Description message identifier configuration ID identifier configuration ID field separator (FS) product class identifier product class field separator (FS) hardware configuration identifier device identifier hardware configuration data group separator (GS) device identifier [1] hardware configuration data [1] [1] Code ‘H’ ’A’ --:1C ’B’ --:1C ’C’ ----[:1D] [---] [---] No.Messages Hardware Configuration Data NDC Status Messages This solicited status message is sent to central in response to a Send Configuration Information terminal command message with command code ’7’ and command modifier ’1’. Message identifier Field size: 1 Valid range: ’H’ Description: This message is sent to central in response to a send configuration information terminal command message (command code ’7’ inclusive command modifier ’1’). devided through group separators. of Characters 1 1 4 1 1 2 1 1 1 2 1 1 2 [1] These fields. Configuration ID Field size: 4 Valid range: 0000-9999 Description: Contains the last four digit configuration ID number sent to the terminal from host. The following entries are possible: Product class 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C Sytem Type 5663 5674 5675 5684 5685 5688 5665 5670 personaS75 personaS88 personaS40 personaS70 personaS74 personaS84 personaS85 322 October 2004 U25604-J-Z745-1-7600 . Product class ID Identifier (’B’) Field size: 1 Valid range: ’B’ Description: Identifier of the two digit product class that is included in the following two fields of the message.NDC Status Messages Configuration ID Identifier (’A’) Field size: 1 Messages Valid range: ’A’ Description: Identifier of the four digit configuration ID number that follows. Product class Field size: 2 Valid range: 0000-9999 Description: This two character field contains the product class of the terminal. there will be no corresponding Device Identifier subgroup in the field. It contains information for each device indicating which variant of the device is configured and if any other configuration data is available. One subfield consists of Device Identifier and Hardware Configuration Data. Hardware configuration data Field size: 2 1 Valid range: see Table 81: “Device Configuration Table” on page 307.Messages Hardware configuration identifier (’C’) Field size: 1 NDC Status Messages Valid range: ’C’ Description: This field indicates that hardware configuration information of each present device follows. It is devided into a series of subfields separated by group separators. Description: This field contains the two digit hardware configuration information of each present device. If a device is not present. Device identifier Field size: Valid range: Description: This field contains the Device Identifier of each present device. U25604-J-Z745-1-7600 October 2004 323 . Supply status identifier (’A’) Field size: 1 Valid range: ’A’ Description: This field indicates that supply data of each present device follows. If a device is not present. Table 87: Supplies Data Description message identifier supply status identifier device identifier supply status data group separator (GS) [1] device identifier [1] [1] Code ‘I’ ’A’ ----[:1D] [---] [---] No.NDC Status Messages Supplies Data Messages This solicited status message is sent to central in response to a Send Configuration Information terminal command message with command code ’7’ and command modifier ’2’. 324 October 2004 U25604-J-Z745-1-7600 . are repeated for each of the devices present in the ATM. of Characters 1 1 1 VAR 1 1 VAR supply status data [1] These fields. devided through group separators. Message identifier Field size: 1 Valid range: ’I’ Description: This message is sent to central in response to a send configuration information terminal command message (command code ’7’ inclusive command modifier ’2’). there will be no corresponding Device Identifier subgroup in the field. One subfield consists of Device Identifier and following supply data. It is devided into a series of subfields separated by group separators. Table 88: Fitness Data Description message identifier hardware fitness identifier device identifier fitness group separator (GS) [1] device identifier fitness [1] [1] Code ‘J’ ’A’ ----[:1D] [---] [---] No. Message identifier Field size: 1 Valid range: ’J’ Description: This message is sent to central in response to a send configuration information terminal command message (command code ’7’ inclusive command modifier ’3’). Fitness Data This solicited status message is sent to central in response to a Send Configuration Information terminal command message with command code ’7’ and command modifier ’3’. devided through group separators. U25604-J-Z745-1-7600 October 2004 325 . are repeated for each of the devices present in the ATM.Messages Supply status data Field size: VAR NDC Status Messages Valid range: each element of the supplies status data will take one of the following values: ’0’ ’1’ ’2’ ’3’ ’4’ Not configured/reserved Good state Media low Media out Overfill Description: This field contains information for each present device indicating the condition of the parts of the device that are replenishable. of Characters 1 1 1 1 1 1 1 [1] These fields. 326 October 2004 U25604-J-Z745-1-7600 . there will be no corresponding Device Identifier subgroup in the field. It is devided into a series of subfields separated by group separators. indicating the current fitness of the device: ’0’ ’1’ ’2’ ’3’ ’4’ No error/ not supported Routine errors have occurred Warning conditions have occurred.NDC Status Messages Hardware fitness identifier (’A’) Field size: 1 Messages Valid range: ’A’ Description: This field indicates that the hardware fitness of each present device follows. Warning and fatal errors can only be cleared by entering Supervisor Mode or local Supervisor function “Clear Fitness”. Fitness Field size: 1 Valid range: each fitness character is encoded with one of the following error severity values. One subfield consists of Device Identifier and following hardware fitness. Description: This field contains information for each present device indicating the current fitness the device present. The terminal is currently in the suspend mode due to suspected tampering with this device Fatal error condition exists on this device Routine. If a device is not present. investigation required Suspend Mode. of Characters 1 1 5 1 1 VAR Valid range: ’K’ Description: This message is sent to central in response to a send configuration information terminal command message (command code ’7’ inclusive command modifier ’4’). U25604-J-Z745-1-7600 October 2004 327 . Sensor status identifier (’A’) Field size: 1 Valid range: ’A’ Description: This field indicates that a five bytes sensor status follows.1 Description: These 5 bytes represents the same sensor status as reported in the unsolicited Sensor Status message (DID ’P’). Sensor Status Field size: 5 Valid range: 0 . These sensor status bytes are identical to the information reported in bytes 2-6 of the Sensor Status message.Messages Tamper and Sensor Status Data NDC Status Messages This solicited status message is sent to central in response to a Send Configuration Information terminal command message with command code ’7’ and command modifier ’4’. See section ”Sensor Status (unsolicited) (DID ‘P’)” on page 361. Table 89: Tamper and Sensor Status Data Description message identifier sensor status identifier sensor status field separator tamper indicator identifier tamper status Message identifier Field size: 1 Code ‘K’ ’A’ --:1C ’B’ --- No. Tamper Status Field size: VAR Valid range: 0 . 328 October 2004 U25604-J-Z745-1-7600 . Software ID and Release Number This solicited status message is sent to central in response to a Send Configuration Information terminal command message with command code ’7’ and command modifier ’5’. of Characters 1 1 VAR (6) 1 1 VAR (9) See description of the fields on the following page. If a device is not configured. any associated TI byte will take the value ’0’. The characters 8-13 are devices that are not supported by ProCash/NDC and appended as zeros in this message.NDC Status Messages Tamper status identifier (’A’) Field size: 1 Messages Valid range: ’A’ Description: This field indicates that TI sensor status information follows. See section ”Sensor Status (unsolicited) (DID ‘P’)” on page 361. Table 90: Software ID and Release Number Description message identifier release number identifier NDC release number field separator software ID identifier NDC software ID Code ‘L’ ’A’ --:1C ’B’ --- No.1 Description: Character 1-7 of the tamper status data are identical to the information reported in bytes 7-13 of the Sensor Status message. 00). For this release the field is set to following value: G530-0205 (NDC+ Native mode). The third pair of digits represent the patch number (Example : 060000 is release 06. Software ID identifier (’B’) Field size: 1 Valid range: ’B’ Description: This field indicates that the sftware ID follows. NDC Software ID Field size: 9 Valid range: VAR Description: Contains the NDC+ software ID.Messages Message identifier Field size: 1 NDC Status Messages Valid range: ’L’ Description: This message is sent to central in response to a send configuration information terminal command message (command code ’7’ inclusive command modifier ’5’). NDC release number Field size: 6 Valid range: VAR Description: Contains a six digit decimal number.00. The second pair of digits represent the point release number. Release number identifier (’A’) Field size: 1 Valid range: ’A’ Description: This field indicates that a six digit release number follows. The first pair of digits represent the release number. U25604-J-Z745-1-7600 October 2004 329 . NDC Status Messages Local Configuration Option Digits Messages This solicited status message is sent to central in response to a Send Configuration Information terminal command message with command code ’7’ and command modifier ’7’. Local option digits Field size: 16 Valid range: VAR Description: These characters represent the values of the Local Option Digits. Local options identifier (’A’) Field size: 1 Valid range: ’A’ Description: This field indicates that local option digits follows.PPF. 330 October 2004 U25604-J-Z745-1-7600 . of Characters 1 1 VAR (16) Valid range: ’M’ Description: This message is sent to central in response to a send configuration information terminal command message (command code ’7’ inclusive command modifier ’7’). You can enable specific options via parameter LOCAL_MODE_ OPTIONS in configuration file CUSTOM. Table 91: Local Configuration Option Digits Description message identifier local options identifier local option digits Message identifier Field size: 1 Code ‘M’ ’A’ --- No. Table 92: Solicited Status (Device Fault) Description device identifier transaction status field separator error severity field separator diagnostic M-status diagnostic M-data field separator supplies status Device Identifier Field size: 1 Code --VAR [:1C] VAR [:1C] --[---] [:1C] VAR No.Messages NDC Status Messages Solicited Status (device fault) When the status descriptor is ‘8’ .device fault. of Characters 1 17 1 5 1 VAR VAR 1 5 Valid range: See description Description: This field identifies the device by means of a device identification (DID). the following information is present in the status information field. The following table shows DID entries of solicited status messages which Wincor Nixdorf terminals may send in response for transaction reply commands: DID D E F Device card reader/writer cash handler depository U25604-J-Z745-1-7600 October 2004 331 . Device is out of service and will continue to report intervention at the terminal. 3 suspend 4 fatal 332 October 2004 U25604-J-Z745-1-7600 . Continue to use. No error has occurred. A routine error has occurred and diagnostic information follows. Diagnostic information follows. This is sent if cardholder tampering is suspected. Error Severity Field size: 2 Valid range: 0-99 Description: Contains information required to decide locking the device or continue to use. Each character is always coded in the same way: Table 93: Error Severity Table Code 0 1 2 Short Description Detailed Description no error routine error warning Continue to use. Diagnostic information follows. Continue to use but it is recommended that the network operator is informed of the error or exception condition.NDC Status Messages Transaction Status Field size: 17 Messages Valid range: See description Description: Contains information required to make a transaction completion decision. The terminal will suspend transaction processing on completion of the current transaction (state 000 entered). It is recommended that the terminal is put out of service or transactions involving the faulty device are not allowed. The length of the filed is one character with the exception of currency handler which sends five characters. See next section for detailed descriptions for each device. The length of the field is different for each device but each device will always send the same number of characters. U25604-J-Z745-1-7600 October 2004 333 . A cross reference of the M-Data descriptions can be taken from the original Diagnostic Status Code Note Book that can be ordered from NCR. magnetic cards. A-F Description: This field is used to log additional M-Data status information.INA to the vendor specific error code with the closest match to the meaning of the NCR specifc M-Data code. Diagnostic M-Data Field size: 0-30 Valid range: 0-9. M-Data are appended to the M-Status without separator. The M-Status values can be configured (mapped) for each error CLASS and error CODE of vendor specific errors (on Wincor Nixdorf systems CSC-W32 errors) via parameter “M_STATUS” in configuration file CCERRMAP. This field contains one character for each supplies container managed by the device. Supplies Status Field size: 5 Valid range: 0-99 Description: Contains information related to the state of supplies (paper. M-Data contain additional hardware status information of NCR hardware.Messages Diagnostic M-Status Field size: 2 NDC Status Messages Valid range: 0-99 Description: The two digit M-Status contain the NDC specific main error status which gives a global information of the error situation. It can be variable depending on the device. (See also M-Status description).INA. currency. On Wincor Nixdorf systems this hardware status information can be configured (mapped) via parameter “M_DATA” in configuration file CCERRMAP. Please refer to the ProCash/NDC ProConsult/NDC Installation manual section “Customize Error Mapping Table CCERRMAP” how to configure M-Status. envelopes) in the terminal. If this field is omitted it can be assumed that there is no new state on any container. The container has sensed a full condition and should be emptied. The container has reached the low condition. 334 October 2004 U25604-J-Z745-1-7600 .NDC Status Messages Each character is always coded in the same way: Table 94: Supplies Status Table Messages Code 0 1 2 3 4 Short Description Detailed Description no-new-state good state media low media out overfill The state of the container can be assumed as unchanged The state of the container is known to be good (not low empty or overfilled). The container is empty. For devices which report both solicited and unsolicited status messages a common set of transaction device status codes are defined for use in either type of message. Table 95: Unsolicited Device Status Description device identifier (DID) device status field separator error severity field separator diagnostic M-status diagnostic M-data field separator supplies status Device Identifier (DID) Field size: 1 Code --VAR [:1C] VAR [:1C] --[---] [:1C] VAR No. Device Status Field size: 13 Valid range: See description Description: Used for recording any transaction exceptions of device state changes.Messages NDC Status Messages Unsolicited Device Status The following table shows the structure of the status information field in unsolicited status messages of NDC. of Characters 1 13 1 5 1 VAR VAR 1 5 Valid range: See description Description: This field identifies the device by means of a device identification (DID). U25604-J-Z745-1-7600 October 2004 335 . When processing a transaction reply command any unsolicited transaction exceptions are reported prior to the solicited device fault or ready status. NDC Status Messages Error Severity Field size: 2 Messages Valid range: 0-99 Description: See section ”Solicited Status (device fault)” on page 331 Diagnostic M-Status Field size: 2 Valid range: 0-99 Description: The two digit M-Status contain the NDC specific main error status which gives a global information of the error situation. Supplies Status Field size: 5 Valid range: 0-99 Description: See section ”Solicited Status (device fault)” on page 331 336 October 2004 U25604-J-Z745-1-7600 . M-Data contain additional hardware status information of NCR hardware. Diagnostic M-Data Field size: 0-30 Valid range: 0-9. It can be variable depending on the device. The M-Status values can be configured (mapped) for each error CLASS and error CODE of vendor specific errors (on Wincor Nixdorf systems CSC-W32 errors) via parameter “M_STATUS” in configuration file CCERRMAP. M-Data are appended to the M-Status without separator.INA. A cross reference of the M-Data descriptions can be taken from the original Diagnostic Status Code Note Book that can be ordered from NCR. (See also M-Status description).INA to the vendor specific error code with the closest match to the meaning of the NCR specifc M-Data code. On Wincor Nixdorf systems this hardware status information can be configured (mapped) via parameter “M_DATA” in configuration file CCERRMAP. Please refer to the ProCash/NDC ProConsult/NDC Installation manual section “Customize Error Mapping Table CCERRMAP” how to configure M-Status. A-F Description: This field is used to log additional M-Data status information. / Code Characters Unsol.Messages Power Up (unsolicited) (DID ‘B’) NDC Status Messages This message is used to inform the host that a power interruption or system reboot has occurred. Under such circumstances. the message cannot be sent until the communication with the host has been reestablished. of Sol. Four characters (‘0000’ ‘9999’) defining the configuration number of the customization data. The host ensures that the terminal has the correct CI before sending a go in service command. 1 4 U B VAR Detailed Definition Indicates a power failure. U25604-J-Z745-1-7600 October 2004 337 . The status field for this type message is composed of the following sub fields: Description Device Identifier Device Status No. The mechanism failed to update Track 3 on the card./unsol. diagnostic status or supplies status changes. Invalid Track 3 data received from Central This is a single character field coded in the standard way to be used to make a shutdown decision./ Code Characters Unsol. S/U 1 S/U 2 S/U 3 S/U Error Severity 1 4 0-4 Diagnostic M-status and M-Data 2-10 00 01 02 03 04 05 06 07 338 October 2004 U25604-J-Z745-1-7600 . 1 U D 0 Messages Detailed Definition Indicates a card reader unit message No transaction exception condition occurred but consult other fields for error severity. Operation successful Blank track Track not supported Read error Write error No card in reader at start of command Card removed during capture Shutter jammed open Transaction 1 Device Status.NDC Status Messages Card Reader (sol. Cardholder did not take his card within the allowed time and it was captured or jammed. The mechanism failed to eject the card and it was captured or jammed. gives details of any transaction related exception condition detected while processing a card at the terminal.) (DID ‘D’) Description Device Identifier No. of Sol. of Sol./ Code Characters Unsol. (slow) Invalid card detected CIM service test failed Error in track 3 data CROPF feature not supp. 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 33 35 37 38 40 Detailed Definition Shutter switch failure detected Error recovery successful shutter jammed closed Card jam (not during capture) Card captured after unsuccessful eject Possible cardholder tampering Too many consecutive read errors Too many consecutive write errors Too many consecutive card jams Too many consecutive shutter jammed closed Card jam during capture Too many consecutive invalid cards Device still inoperative No card during clean test Speed out of spec. (fast) Speed within +3% Speed within +-1% Speed within -3% Speed out of spec.Messages NDC Status Messages Description No. LFCC bin full soon/full LFCC bin removed U25604-J-Z745-1-7600 October 2004 339 . 41 50 51 Detailed Definition CROPF feature failure Card not in SCRW stage position Smart card stopper pin or contacts lowered.NDC Status Messages Messages Description No.doesn’t exist Password not decimal Password no match Key integrity error Key parity error Invalid data format Stopper PIN failure Contact unit failure Card movement failure 52 53 54 55 56 57 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 340 October 2004 U25604-J-Z745-1-7600 ./ Code Characters Unsol. of Sol. unable to capture Invalid smart card command code error Invalid smart card command data error SCIF not configured/not responsing SCIF response timeout exeeded Card reader is in SCRW mode (diagnostics only) Invalid smart card response length Invalid SCIF command code Invalid SCIF command format No smart card encryptor response error Invalid key ID Invalid key type Invalid parent key type Invalid key . / Code Characters Unsol. Power up ime exceeded ANSI PIN block error CIM self test failed CIM security module defective CIM security module communication failure CIM interface board defective CIM interface board communication failure No new state No overfill condition Overfill condition Supplies Status 1 0 1 4 U25604-J-Z745-1-7600 October 2004 341 . 79 80 81 82 83 84 85 86 87 88 89 90 91 Detailed Definition Smart card switch off failure Smart card removed error No smart card response Smart card transmission error Smart card switched off Illegal card type/param.Messages NDC Status Messages Description No. of Sol. but an exception condition occurred which is detailed in later fields. Successful operation. Short dispense No notes dispensed Faulty dispense. This status is returned on a card before cash transaction if the stack operation fails and the notes are purged prior to card eject. of Sol. Notes dispensed unknown. U 0 S S S 1 2 3 S 4 U 5 Characters 2-9 (T-Data) contain notes dispensed counts./ Code Characters Unsol./unsol. Some notes have been retracted following a Present and Notes not taken time-out.NDC Status Messages Dispenser (sol.) (DID ‘E’) Description Device Identifier No. gives details of a dispense operation in response to a transaction reply command message. No notes dispensed or card not ejected. The following counts contain requested dispense values. 1 E Messages Detailed Definition Indicates a dispenser solicited or unsolicited message. Each pair of characters represents a twodigit decimal value in range 00-99 per cassette type Characters 2-3 4-5 6-7 8-9 342 October 2004 U25604-J-Z745-1-7600 . The number of notes retracted is unknown. Cass Types logical cassette 1 logical cassette 2 logical cassette 3 logical cassette 4 Transaction Status 1 (T-code plus T-data). of Sol. 2-32 00 01 02 03 04 05 06 07 08 09 10 11 No error Pick requested from noninstalled cassette Too many bills being rejected Pick failure Pick failure and low (out of bills) Sensor failure or currency jam Divert gate fault Reject bin inoperative Reject bin overfill Comm failure between dispenser and terminal Fatal previous error Unrecovered previous error U25604-J-Z745-1-7600 October 2004 343 . Severity related to cassette type 4. Severity related to cassette type 1.Messages NDC Status Messages Description Error Severity Character ’0’ Character ’1’ Character ’2’ Character ’3’ Character ’4’ Diagnostic M-status and M-data No. 5 0-4 Detailed Definition Severity info related to complete device. Severity related to cassette type 2. Severity related to cassette type 3./ Code Characters Unsol. NDC Status Messages Messages Description No./ Code Characters Unsol. 12 13 14 15 Detailed Definition Present mechanism failed or jammed Exit shutter jammed open Exit shutter jammed closed Bills passing overfill sensor on present operation Timing disk did not operate correctly Exit sensor failed to clear Timing disk did not operate correctly Exit sensor blocked initially on next operation Not configured Security violation Security inhibition Reserved An area of NVRAM cannot be accessed Presenter transport timing disk did not operate correctly or motor failed One of the presenter transport sensors failed clear or blocked Reserved Heartbeat on execution processor failed (80652) Communications failure on the I2C bus of the execution processor 16 17 18 19 20 21 22 23-27 28 29 30 31 32 33 344 October 2004 U25604-J-Z745-1-7600 . of Sol. / Code Characters Unsol. Pick valve test not attempted because cassettes were installed TI service switched ON TI service switched OFF LVDT or associated circuitry malfunctioning Bill parameters not configured An attempt to pick from a cassette which has been disabled for In Service Replenishment 35 36 37 38 39 40 41 Supplies Status.’4’) 0 1 4 0 1 2 3 no new state no overfill condition overfill condition no new state Sufficient notes Low on notes Out of notes U25604-J-Z745-1-7600 October 2004 345 . of Sol. Operation incomplete due to ac and 24V dc power disconnection through interlock. 34 Detailed Definition A present bills operation has been attempted without any bills being stacked or a retract operation has been attempted with no bills presented. types 1-4 (character ’1’ . Codes for the reject cassette (character ’0’) Codes for disp. 5 Indicates the state of the reject bin and currency cassettes. cass.Messages NDC Status Messages Description No. Transaction Status 1 (T-code plus T-data). but an exception condition occurred which is detailed in the following field. Failure to enable mechanism for a deposit Deposit failed.) (DID ‘F’) Description Device Identifier No. Successful operation./ Code Characters Unsol. of Sol. 1 F Messages Detailed Definition Indicates a depository solicited or unsolicited message. gives details of a deposit operation in response to a transaction reply command message U 0 S S S 1 2 3 S 4 Error Severity 1 0-4 346 October 2004 U25604-J-Z745-1-7600 ./unsol.NDC Status Messages Depository (sol. cardholder has access to envelope. Deposit failed. Time-out on cardholder deposit. This status is also returned if there is any doubt about cardholder access. cardholder does not have access to envelope This is a single character field coded in the standard way to be used to make a shutdown decision. Messages NDC Status Messages Description Diagnostic M-status and M-data No. error count exceeded Deposit bin overfill Timing disk failure Transport motor failure Anti fishing sensor error Motor speed too fast Print head removed Interlock failed no envelope deposited no overfill condition overfill detected Supplies Status 1 0 1 4 U25604-J-Z745-1-7600 October 2004 347 . 2-22 00 01 02 03 04 05 06 07 08 09 10 11 13 15 50 51 52 55 Detailed Definition No error Transport jam Transport jam and shutter jammed open Transport jam and shutter jammed closed Shutter jammed open Shutter jammed closed Transport sensor failure Communication failure within the atm Invalid device print head status Invalid device module status Deposit not done./ Code Characters Unsol. of Sol. Sufficient envelopes Envelopes low Envelopes exhausted Device Status. 1 \ Detailed Definition indicates a depository solicited or unsolicited message.envelope not presented or retracted This is a single character field coded in the standard way to be used to make a shutdown decision. Envelope presentation successful Failure . See section “Enhanced Configuration Parameters Load” on page 249 for details. of Sol. 1 Indicates whether the last transaction was successful Error Severity 1 U 0 1 0-4 Diagnostic M-status and M-data 2-8 00 01 02 03 04 05 06 Supplies Status 1 1 2 3 348 October 2004 U25604-J-Z745-1-7600 .NDC Status Messages Envelope Dispenser (unsolicited) (DID ‘\’ Messages ProCash/NDC sends unsolicited envelope dispenser messages depending on the value of the enhanced configuration option 23. Description Device Identifier No./ Code Characters Unsol. EMPTY. No error Transport jam before exit sensor Transport jam at exit sensor Exit sensor failure shutter jammed open Bin low sensor failure Timing disk sensor failure Bin is low and failed to present. Successful print Print operation not successfully completed Device not configured This is a single character field coded in the standard way to be used to make a shutdown decision. See table “Error severity table” for details. of Sol. 1 U S G 0 1 NDC Status Messages Detailed Definition Indicates a receipt printer unsolicited message./ Code Characters Unsol. No error Head jam/ Knife jam Failed to go not busy Black mark error Always saw the black mark Paper out Paper not loaded or Paper jam before transport Communication error Printer open Ribbon needs replaced soon Printhead needs replaced soon Knife needs replaced soon Transaction/ 1 Device Status. error severity 1 S 2 0-4 Diagnostic M-status and M-data 2-10 00 01 02 03 04 05 07 08 09 10 11 12 U25604-J-Z745-1-7600 October 2004 349 .Messages Receipt Printer (unsolicited) (DID ‘G’) Description Device Identifier No. Indicates whether or not the print was successfully completed. of Sol. Knife replacement recommended Supplies Status 1 CHAR 0 1 CODE 1 2 3 1 2 3 2 1 2 3 3 1 2 350 October 2004 U25604-J-Z745-1-7600 . 13 14 15 16 Detailed Definition Ribbon needs replaced now Printhead needs replaced now Sideways communication error Eject jam Sufficient paper Paper low Paper exhausted Ribbon o.NDC Status Messages Messages Description No.k. Printhead replacement recommended Printhead replacement mandatory Knife o.k./ Code Characters Unsol.k. Ribbon replacement recommended Ribbon replacement mandatory Printhead o. / Code Characters Unsol. See table “Error severity table” for details. 1 U S S H 0 1 2 NDC Status Messages Detailed Definition Indicates a journal printer unsolicited message. Error Severity 1 0-4 This is a single character field coded in the standard way to be used to make a shutdown decision. of Sol. Successful print. Indicates whether or not the print was successfully completed.Messages Journal Printer (unsolicited) (DID ‘H’) Description Device Identifier No. No error Head jam/ Knife jam Failed to go not busy Black mark error Always saw the black mark Paper out Paper not loaded or paper jam before transport Communication error Printer open Ribbon needs replaced soon Printhead needs replaced soon Knife needs replaced soon Diagnostic M-status and M-data 2-10 00 01 02 03 04 05 07 08 09 10 11 12 U25604-J-Z745-1-7600 October 2004 351 . Print operation not successfully completed Device not configured Transaction/ 1 Device Status. NDC Status Messages Messages Description No. Ribbon replacement recommended Ribbon replacement mandatory Printhead o.k. Printhead replacement recommended Printhead replacement mandatory Supplies Status 1 CHAR 0 1 CODE 1 2 3 1 2 3 2 1 2 3 352 October 2004 U25604-J-Z745-1-7600 ./ Code Characters Unsol. 13 14 15 16 Detailed Definition Ribbon needs replaced now Printhead needs replaced now Sideways communication error Eject jam Sufficient paper Paper low Paper exhausted Ribbon o.k. of Sol. No error Mechanical jam Communication error Black mark error Media jam (fatal). or exit sensor error (warning) Paper out Ribbon needs replaced now (Fatal) Ribbon needs replaced soon (Warning) Transaction/ 1 Device Status. but consult other fields for Error Severity. 1 V NDC Status Messages Detailed Definition Indicates a statement printer sol. In an unsolicited status it indicates a transport error or a cut and deliver error in the close state. of Sol./unsolicited message./unsol./ Code Characters Unsol. In a solicited status it gives details of any transaction oriented faults. diagnostic status or supplies status change.) (DID ‘V’) Description Device Identifier No. Successful print. Print / cut not successful Device not configured Statement present in transport Cardholder pressed cancel during a “print statement and wait” function This is a single character field coded in the standard way to be used to make a shutdown decision. See table “Error severity table” for details.Messages Statement Printer (sol. Error Severity 1 U 0 S/U S U U 1 2 3 4 0-4 Diagnostic M-status and M-data 2-32 00 01 02 04 05 07 08 08 U25604-J-Z745-1-7600 October 2004 353 . 2-16 09 10 10 11 16 17 18 Detailed Definition Knife needs replaced soon Printhead needs replaced now (Fatal) Printhead needs replaced soon (Warning) Printer left open Capture jam Media removed by customer during capture Media stuck in throat./ Code Characters Unsol. unable to pull into printer possible customer tampering No paper present at start of command Printer malfunction paper present Bin overfill Print attempted beyond end of media Printer fatal Buncher communications failure Clamp drive jammed open Clamp drive jammed open Capture bin full 19 20 21 22 23 33 34 35 36 354 October 2004 U25604-J-Z745-1-7600 . of Sol.NDC Status Messages Messages Description Diagnostic M-status and M-data No. Knife replacement recommended Knife replacement mandatory Capture bin o. Capture bin overfill U25604-J-Z745-1-7600 October 2004 355 . 1 CHAR CODE 0 1 2 3 1 1 2 3 2 1 2 3 3 1 2 3 4 1 4 Detailed Definition Sufficient paper Paper low Paper exhausted Ribbon o. of Sol./ Code Characters Unsol.Messages NDC Status Messages Description Supplies Status No. Printhead replacement recommended Printhead replacement mandatory Knife o. Ribbon replacement recommended Ribbon replacement mandatory Printhead o.k.k.k.k. No error Failed to close Failed to open Jammed. 1 1 1 U J 1 0-4 Messages Detailed Definition Indicates a vandal guard unsolicited message./ Code Characters Unsol. of Sol. See table “Error severity table” for details. Always ‘0’ for the vandal guard.NDC Status Messages Vandal Guard (unsolicited) (DID ‘J’) Description Device Identifier Device Status Error Severity No. position undefined Diagnostic M-status and M-data 2-6 00 01 02 03 356 October 2004 U25604-J-Z745-1-7600 . This is a single character field coded in the standard way to be used to make a shutdown decision. Module (unsolicited) (DID ‘L’) Description Device Identifier No. No error Parity error Hardware error Key transport error No key Invalid command as keyboard is currently enabled Communication failure Security module reset was successful Invalid command data data mismatch No key loaded in DEU prior to requesting an encr./ Code Characters Unsol. 1 L NDC Status Messages Detailed Definition Indicates an EDM module unsolicited message. EDM error EDM not configured This is a single character field coded in the standard way to be used to make a shutdown decision. See table “Error severity table” for details. of Sol. or decr.Messages EDM . operation Device Status Error Severity 1 1 U 1 2 0-4 Diagnostic M-status and M-data 2-10 00 01 02 03 04 05 07 08 11 12 13 U25604-J-Z745-1-7600 October 2004 357 . Keyspace ID2 has wrong attribute or class. outside 0 -15. Key ID2 not a keyspace specified or keyspace specified not a child of key ID2 keyspace. Key spaces do not match. Invalid keyspace. 16 17 18 19 20 22 23 24 25 26 27 28 29 30 32 358 October 2004 U25604-J-Z745-1-7600 . 15 Detailed Definition Set up failure . Key ID outside maximum range of keys. Invalid parent ID. Keyspace is not a parent. keyspace not created Secret keyspace creation disabled. of Sol. wrong access right Only two RAR access spaces allowed. Keyspace already exists. Keyspace does not exist Keyspace ID1 has wrong attribute or class. can not have secret child.NDC Status Messages Messages Description No. Parent keyspace is a programmer. keyspace not a parent or keyspace does not exist. Invalid parent format.key space ID1 already exists and is not a programmer parent with E/D attribute and 17 keys Invalid keyspace ID format./ Code Characters Unsol. Invalid left shift. Modulus bit length > 576 or Exponent bit length > 576 or Modulus bit length <= exonent bit length. Invalid POST PIN PAD digit (> 0F hex). Invalid length. 33 34 37 38 39 40 41 Detailed Definition Key ID1 has wrong attribute. Invalid attribute field. Invalid PRE PIN PAD data length (> 0C hex). Invalid parameter field. Invalid mode for this function. value out of range. 48 49 50 51 52 53 54 55 56 57 58 59 60 U25604-J-Z745-1-7600 October 2004 359 . no PIN encryption allowed. Key ID2 does not specify an IV. Invalid key ID. Key ID2 has wrong attribute. no key Invalid key ID. Invalid key ID. Attribute already in family. key may not be exclusively ORed with key from different keyspace. of Sol. Invalid key. Variation index already in family. Undefined parameter for keyspace class. key does not exist./ Code Characters Unsol. Invalid access right.Messages NDC Status Messages Description No. or length and offset outside range. Variation index outside range 01-7F hex. or TRS<>00 00 00 00./ Code Characters Unsol. 70 74 75 76 97 98 99 360 October 2004 U25604-J-Z745-1-7600 . of Sol.NDC Status Messages Messages Description No. Key integrity error. Timeout error. when decrypted. Invalid PIN. TC<>41. PIN verification failed. no encryption allowed (truncated PIN does not contain decimal digits). Keyspace inaccessible. 64 65 66 Detailed Definition Password does not contain decimal digits Invalid password. password error count exceeded. no match. Communication error. Invalid PIN encrypt type function (encryption mode changed). Always ‘2’ indicating a warning. of Sol. of Char Characters 1 13 1 Code P ‘1’ Detailed Definition Indicates a Sensor status message. Description Device Identifier Device Status No. Local intervention required. 1 1 U N 1 NDC Status Messages Detailed Definition Indicates a door access unsolicited message. tamper indicating bin in/out conditions and alarm conditions. No error Bad read error Time-out error Comms error Not configured Error Severity 1 2 Diagnostic M-status and M-data 2-4 00 01 02 03 05 Sensor Status (unsolicited) (DID ‘P’) This message is sent on Supervisor mode entry and exit.. Always ‘1’ indicating that access is possibly inhibited. See also ProCash/NDC ProConsult/NDC Installation manual section [APPLICATION_XXX]. ’TI’ sensor change (characters 2-13 give complete definition of all sensors) Mode change (characters 3-13 are omitted) Alarm state change Supervisor mode exit Supervisor mode entry Not applicable ‘2’ ‘3’ If byte 1 = ’2’ If byte 1 = ’1’ 2 2 ‘0’ ‘1’ U25604-J-Z745-1-7600 October 2004 361 ./ Code Characters Unsol.Messages Door Access (unsolicited) (DID ‘N’) Description Device Identifier Device Status No. of Char Characters 3 Code ‘0’ ‘1’ Detailed Definition Vibration and/or heat sensor inactive Vibration and/or heat sensor active Door has been closed Door has been opened Silent signal sensor inactive Silent signal sensor active Electronics enclosure sensor inactive Electronics enclosure sensor active Deposit bin out Deposit bin in Card bin out Card bin in Currency reject bin out Currency reject bin in Cassette in position 1 out Cassette in position 1 in Cassette in position 2 out Cassette in position 2 in Cassette in position 3 out Cassette in position 3 in Cassette in position 4 out Cassette in position 4 in 4 5 ‘0’ ‘1’ ‘0’ ‘1’ 6 ‘0’ ‘1’ 7 8 9 10 11 12 13 ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’ 362 October 2004 U25604-J-Z745-1-7600 .NDC Status Messages Messages Description No. ’98’ Select menu Replenishment menu Configure menu Access menu In Service Supervisor menu Exit menu Exit menu Menu item selected Detailed Definition Indicates a Sensor status message. See also ProCash/NDC SOP Programmers Reference manual for detailed descriptions. device identifier 1 device status VAR (4 max) ’00’ . Description No. Supervisor key messages are supported in ProCash/NDC-SOP only.Messages Supervisor Key Messages (unsolicited) (DID ‘R’) NDC Status Messages This message sends supervisor key messages from the terminal to inform the host of the functions selected by the operator after entry to supervisor mode. of Char Chars Code R 1-2 or 1 ’0’ ’1’ ’2’ ’3’ ’4’ ’7’ ’8’ ’00’ . They can be configured via parameter “MESSAGE_MODE”.’98’ Key selection from Select menu 2-3 or 1-2 3-4 ’00’ .’98’ Host menu Host function U25604-J-Z745-1-7600 October 2004 363 . The following table describes the message format of the EJU message. of Characters 1 1 1 1 1 1 6 6 6 6 6 3 0-350 Valid range: 6 Description: This field specifies the message identifier. Table 96: Electronic Journal Upload message format Description Message Identifier Message Modifier field separator field separator field separator field separator Machine Number Date Time Last Char Previous Block Last Char This Block Block Length Response Data Message Identifier Field size: 1 character Code 6 1 :1C :1C :1C :1C VAR VAR VAR VAR VAR [:1C] VAR No. Please refer to section ”Electronic Journal Upload (EJU) commands” on page 295 for detailed descriptions about EJU command messages.NDC Status Messages Messages Electronic Journal Upload (EJU) Message This section describes the message format of the Electronic Journal Upload (EJU) message that will be sent in response to an Options And Timers or Acknowledge And Continue command. The message identifier of the Electronic Journal Upload message is 6. 364 October 2004 U25604-J-Z745-1-7600 . 000 character count which starts at zero when the EJU is conffollowing a restart start of the terminal. Last Char Previous Block Field size: 6 characters Valid range: 000000-999999 Description: The last Char Previous Block and Last Char This Block values are based on modulus 1. Date Field size: 6 characters Valid range: 000000-999999 in format YYMMDD Description: This field contains the date (from internal system clock of the terminal) when the EJ block was sent to the host.000. Machine Number Field size: 6 characters Valid range: 000000-999999 Description: This field contains the machine number from the terminal. The count is incremented for each character written to the electronic journal.Messages Message Modifier Field size: 1 character NDC Status Messages Valid range: 1 Description: This field specifies the message modifier. Time Field size: 6 characters Valid range: 000000-999999 in format HHMMSS Description: This field contains the time (from internal system clock of the terminal) when the EJ block was sent to the host. U25604-J-Z745-1-7600 October 2004 365 . The Message Modifier 1 indicates this message as Electronic Journal Upload data. If no electronic data available to sent. the response data size is zero. The Last Character Previous Block field can be used by the host for checks on message received.NDC Status Messages Last Char This Block Field size: 6 characters Messages Valid range: 000000-999999 Description: The terminal compares the last Character Received field in the acknowledgement message sent from the host with the Last Character This Block field of the last EJU data message that is sent to the host. 366 October 2004 U25604-J-Z745-1-7600 . If these two values are not the same. Response Data Field size: up to 350 bytes Valid range: 0-350 Description: Electronic Upload Data consists of ASCII text with carriage return (CR) at the end of each line. the acknowledgement message is ignored. U25604-J-Z745-1-7600 October 2004 367 . WOSA passes the data to CSC-W32.Printers Printer Models ProCash/NDC and ProConsult/NDC support all models of printers that are listed in Table 97. Please refer also to the ProCash/NDC ProConsult/NDC Installation manual for detailed descriptions about printer utilities. The current ProCash/NDC and ProConsult/NDC releases support following printer models as listed in the following table: Table 97: Printer Models Models ND71 ND99 ND98 ND9A ND9E ND9C ND9D ND9G TH30 TH21 TH23 TH97 TH97/G TP01 TP07 TP06 NP07 NP06 Printer Description RECEIPT/JOURNAL dot matrix printer (obsolete) THERMO RECEIPT printer (obsolete) JOURNAL dot matrix printer RECEIPT dot matrix printer RECEIPT dot matrix printer RECEIPT Thermal printer JOURNAL Thermal printer RECEIPT Thermal printer (only GDI interface) JOURNAL Thermal printer RECEIPT Thermal printer (optional with GDI interface) STATEMENT Thermal printer (optional with GDI interface) STATEMENT dot matrix printer STATEMENT Thermal printer (optional with GDI interface) STATEMENT Thermal printer (optional with GDI interface) RECEIPT Thermal printer (optional with GDI interface) JOURNAL dot matrix printer (optional with GDI interface) RECEIPT dot matrix printer JOURNAL dot matrix printer Detailed descriptions can be taken from the hardware specification manuals. See also CSC-W32 Programmers Reference. Then the macros are transfered to the WOSA service. All printer control characters of ProCash/NDC or ProConsult/NDC will be initiated via macros. < = > ? No. positions the next graphic character in the next tab column.Printer Control Characters Printers Printer Control Characters The following tables gives a short description about control sequences used in the NDC+ message protocol. Table 98: NDC Printer control characters Control Character LF FF ASCII Code 0AH 0CH Short Description Line Feed. This 'SO' character is followed by a single graphic character indicating the desired number of spaces: Character 1-9 : . Fills an area of the printer form with spaces. cut and deliver to customer. Causes a feed to the next TOF mark or feed to the maximum receipt length. sets Single Alpha 1 char set size (10 CPI) sets Single Alpha 2 char set size (10 CPI) see Note sets Single Alpha 3 char set size (10 CPI) see Note sets Double Alpha 1 char set (5 CPI) sets Double Alpha 2 char set size (5 CPI) sets Double Alpha 3 char set size (5 CPI) sets Condensed Alpha 1 char set size (17 CPI) ESC (1 ESC (2 ESC (7 ESC (> ESC (? ESC (B ESC (C 1B (1 1B (2 1B (7 1B (> 1B (? 1B (B 1B (C 368 October 2004 U25604-J-Z745-1-7600 . of spaces 1-9 10 11 12 13 14 15 SO 0EH HT 09H Horizontal tabulators. which are supported by ProCash/NDC and ProConsult/NDC. Tabs are defined to be in every eighth column from the left margin. causes the next graphic character to be printed on the next line. the printer switches to the user defined character set.JRN YYYY MM DD .Printers Electronic journal Control Character ESC (D ESC (E ESC [pxxx ESC [qxxx ESC [rxx ESC %xxx ASCII Code 1B (D 1B (E 1B [pxxx 1B [qxxx 1B [rxx 1B %xxx Short Description sets Condensed Alpha 2 char set size (17 CPI) sets Condensed Alpha 3 char set size (17 CPI) left margin control right margin control lines per inch control sets printer code page xxx. See also section [TOPMSG] and [CUSTMSG] in configuration file CUSTOM. Electronic journal storage The journal file will be created daily and have the following format: YYYYMMDD.PPF. The predefined path of the journal files on the harddisk is C:\JOURNAL and C:\CUSTUMER. See also ProCash/NDC ProConsult/NDC Installation manual section ’Printer Fonts’ for details.JRN U25604-J-Z745-1-7600 October 2004 369 . Electronic journal Wincor Nixdorf terminals are able to log all journal printer messages into journal files which are stored on the PC hard disk. 000 = set user charset If character set Alpha 2 or Alpha 3 is sent from host.JRN represents the current 4 digit year represents the current 2 digit month represents the current 2 digit day is the file extension EXAMPLE: 19990701. PPF where you can see the default journal output definitions Printing with the Windows GDI Interface ProCash/NDC and ProConsult/NDC supports raw printing via the Windows GDI Interface. The printer has to be installed as a Windows printer. In Table “Printer Models” on page 367 you can see what type of printer can or must be installed as a Windows printer. out-of-service. supervisor mode) See also section [TOPMSG] and [CUSTMSG] of configuration file CUSTOM. All detailes about configuration and GDI print technology in ProCash/NDC or ProConsult/NDC are described in the GDI Printer Overlay Framework User Guide and ProCash/DDC ProConsult/DDC Installation manual. paper supply status and status of the printer hardware. Printing via GDI requires graphic able printers. which support Windows printing via a Windows printer driver. 370 October 2004 U25604-J-Z745-1-7600 . In addition an associated port monitor has to be installed to get status information about printed jobs.Printing with the Windows GDI Interface Printers Types of journal information Following information can be stored into the electronic journal files: q q q q q q q q q date and time device errors transaction reply printer data operation code buffer and requested amount ID-card track 2 data ID-card track 3 data Transaction Reply command of reply dispense data ATM modes (in-service. offline. Additional Useful Information NDC Standard Character Sets Single Pixel Single Arabic U25604-J-Z745-1-7600 October 2004 371 . NDC Standard Character Sets Single Graphic 1 Additional Useful Information Single Graphic 2 Single Graphic 3 372 October 2004 U25604-J-Z745-1-7600 . Additional Useful Information Single Alpha 1 NDC Standard Character Sets Single Alpha 2 U25604-J-Z745-1-7600 October 2004 373 . NDC Standard Character Sets Double Arabic Additional Useful Information Double Alpha 1 374 October 2004 U25604-J-Z745-1-7600 . Additional Useful Information Double Alpha 2 NDC Standard Character Sets Chinese 1 Chinese 2 U25604-J-Z745-1-7600 October 2004 375 . ASCII to EBCDIC Code Conversion Table Additional Useful Information ASCII to EBCDIC Code Conversion Table GRAPHIC ASCII (HEX) EBCDIC (HEX) GRAPHIC ASCII (HEX) EBCDIC (HEX) NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 00 01 02 03 37 2D 2E 2F 16 05 15 0B 0C 0D 0E 0F 10 11 12 13 3C 3D 32 26 18 19 3F 27 SPACE ! " # $ % & ( ) * + . 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 40 4F 7F 7B 5B 6C 50 7D 4D 5D 5C 4E 6B 60 4B 61 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 7A 5E 376 October 2004 U25604-J-Z745-1-7600 . / 0 1 2 3 4 5 6 7 8 9 : . . Additional Useful Information ASCII to EBCDIC Code Conversion Table GRAPHIC ASCII (HEX) EBCDIC (HEX) GRAPHIC ASCII (HEX) EBCDIC (HEX) FS GS RS US @ A B C D E F G H I J K L M N O P Q R S T U V W X Y 1C 1D 1E 1F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 1C 1D 1E 1F 7C C1 C2 C3 C4 C5 C6 C7 C8 C9 D1 D2 D3 D4 D5 D6 D7 D8 D9 E2 E3 E4 E5 E6 E7 E8 < = > ? ' a b c d e f g h i j k l m n o p q r s t u v w x y 3C 3D 3E 3F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 4C 7E 6E 6F Undefined 81 82 83 84 85 86 87 88 89 91 92 93 94 95 96 97 98 99 A2 A3 A4 A5 A6 A7 A8 U25604-J-Z745-1-7600 October 2004 377 . Screen Design Worksheet Additional Useful Information GRAPHIC ASCII (HEX) EBCDIC (HEX) GRAPHIC ASCII (HEX) EBCDIC (HEX) Z [ \ ] ^ _ 5A 5B 5C 5D 5E 5F E9 4A E0 5A 5F 6D z { | } DEL 7A 7B 7C 7D 7E 7F A9 C0 6A D0 A1 07 Screen Design Worksheet @ A B C D E F G H I J K L M N O 0 1 2 3 4 5 6 7 8 9 : @ A B C D E F G H I J K L M N O 0 1 2 3 4 5 6 7 . < = > ? P Q R S T U V W 378 October 2004 U25604-J-Z745-1-7600 . INA) and how to update the contents into the Windows registry. Table 99: Cash Dispenser V1 (Class: 0007) Error Error Class Code 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 DEFA_W DEFA_E 0100_E 0200_E 0300_E 0400_E 1000_E 1100_E 1200_E 1300_E 1400_E 1500_E 1600_E 1700_E 1800_E 1900_E 1A00_E 1B00_E 1C00_E Sev. In addition you will find reference tables of application error codes (so called LYNX errors as nick name. which can be identified by the class numbers 64xx).\ProTopas\CurrentVersion\CCERRMAP\ is devided in error sub sections where in each section the M-Status and M-Data status code is mapped. See ProCash/DDC ProConsult/DDC Installation manual section "Parameter Management" for details about setting up the error mapping table (CCERRMAP. will not produced any more). The registry path . 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 03 09 08 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00002727272700000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO ”DISPENSER V1: Default warning if no CSCW32 error found” ”DISPENSER V1: Default error if no CSCW32 error found” ”DISPENSER V1: No cash in collecting tray” ”DISPENSER V1: Transport direction illegal” ”DISPENSER V1: Remaining capacity of reject bin to small” ”DISPENSER V1: Syntax error in job” ”DISPENSER V1: Incorrect block length. The error mapping can be customized in configuration file "CCERRMAP. error in job” ”DISPENSER V1: Wrong job specification” ”DISPENSER V1: Incorrect job length” ”DISPENSER V1: Addressed cassette does not exist” ”DISPENSER V1: Attempt to read from an unknown area” ”DISPENSER V1: Field name in job unknown” ”DISPENSER V1: Syntax error in job” ”DISPENSER V1: Invalid transport destination” ”DISPENSER V1: Illegal separator used in the job” ”DISPENSER V1: A job was previously issued and is still busy” ”DISPENSER V1: Attempt to write to protected cass. Detailed descriptions about CSC-W32 error codes of each device class are described in the manual CSC-W32 System Messages (available on the Wincor Nixdorf Intranet server).INA".M-Status & M-Data Reference Tables The following tables show the CSC-W32 device error classes that are mapped to the NDC Maintenance M-Status and M-Data error codes. EEPROM” ”DISPENSER V1: There is no PUT PROM in the cash-out controller” U25604-J-Z745-1-7600 October 2004 379 . CSC-W32 Error Classes Cash Dispenser V1 (old series) (Class: 0007) The following table lists the M-Status and M-Data codes assigned to the device class Cash Dispenser V1 (old series.. error in job” ”DISPENSER V1: Incorrect device specification. dispenser module” ”DISPENSER V1: Time-out of path monitor in 5. dispenser module” ”DISPENSER V1: Time-out of path monitor in 3. dispenser module” ”DISPENSER V1: Time-out of path monitor in 4.L25” ”DISPENSER V1: Times-out of path monitor in 1.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 1D00_E 2000_E 2100_E 2200_E 2300_E 2400_E 2500_E 2600_E 2700_E 2800_E 2900_E 2A00_E 2B00_E 2C00_E 2D00_E 3100_E 3200_E 3300_E 3400_E 3500_E 5000_E 5100_E 5110_E 5111_E 5118_E 5119_E 5200_E 5210_E 5211_E 5218_E 5219_E 5300_E 5400_E 5410_E 5418_E 5500_E 5510_E 5511_E 5518_E 5519_E 5610_E 5611_E 5618_E 5619_E 5700_E 5710_E 5800_E 5810_E 5B00_E 5B10_E 5B11_E 5B12_E 5B13_E 5C00_E 5C10_E 5C11_E 5C12_E 5C13_E 5D00_E 5D10_E 5D11_E 5F10_E Sev. dispenser module” ”DISPENSER V1: Photosensor L17 blocked” ”DISPENSER V1: Photosensor L18 or L22 blocked” ”DISPENSER V1: Photosensor L18 does not become free” ”DISPENSER V1: Photosensor L18 does not become free” ”DISPENSER V1: Photosensor L18 is not reached” ”DISPENSER V1: Photosensor L18 is not reached” ”DISPENSER V1: Photosensor L19 blocked” ”DISPENSER V1: Photosensor L19 does not become free” ”DISPENSER V1: Photosensor L19 does not become free” ”DISPENSER V1: Photosensor L19 is not reached” ”DISPENSER V1: Photosensor L19 is not reached” ”DISPENSER V1: Photosensor L20 blocked” ”DISPENSER V1: Photosensor L21 blocked” ”DISPENSER V1: Photosensor L21 does not become free” ”DISPENSER V1: Photosensor L21 is not reached” ”DISPENSER V1: Photosensor L22 does not become free” ”DISPENSER V1: Photosensor L22 does not become free” ”DISPENSER V1: Photosensor L22 does not become free” ”DISPENSER V1: Photosensor L22 is not reached” ”DISPENSER V1: Photosensor L22 is not reached” ”DISPENSER V1: Photosensor L23 does not become free” ”DISPENSER V1: Photosensor L23 does not become free” ”DISPENSER V1: Photosensor L23 is not reached” ”DISPENSER V1: Photosensor L23 is not reached” ”DISPENSER V1: Does not reach the bottom Collecting tray swivel arm” ”DISPENSER V1: Swivel arm does not reach the bottom” ”DISPENSER V1: Collecting tray swivel arm does not reach the top” ”DISPENSER V1: Swivel arm does not reach the top position” ”DISPENSER V1: Money slot/shutter does not close completely” ”DISPENSER V1: Shutter was not closed completely” ”DISPENSER V1: Shutter was not closed completely” ”DISPENSER V1: Shutter was not closed completely” ”DISPENSER V1: Shutter was not closed completely” ”DISPENSER V1: Money slot/shutter does not open completely” ”DISPENSER V1: Shutter was not open completely” ”DISPENSER V1: Shutter was not completely open” ”DISPENSER V1: Shutter was not completely open” ”DISPENSER V1: Shutter was not completely open” ”DISPENSER V1: Money does not reach L17” ”DISPENSER V1: Transport motor M2 does not return timing pulses” ”DISPENSER V1: Transport motor M2 does not return timing pulses” ”DISPENSER V1: Photosensor L25 blocked” 380 October 2004 U25604-J-Z745-1-7600 . dispenser module” ”DISPENSER V1: Time-out of path monitor in 2.L17. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 03 05 05 05 05 07 02 03 04 01 00 05 20 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 MData 00000000000000000000 00000303030300000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO ”DISPENSER V1: Illegal specification transferred in SV job” ”DISPENSER V1: Amount demanded cannot be dispensed” ”DISPENSER V1: Time-out in photosensor of measuring station” ”DISPENSER V1: Time-out photosensor L1” ”DISPENSER V1: Time-out for collecting tray photosensor L19” ”DISPENSER V1: Time-out in photosensor L20 for reject cassette” ”DISPENSER V1: Single reject switch defective” ”DISPENSER V1: All banknotes were identified as multiple dispenses” ”DISPENSER V1: The dispenser module is defective” ”DISPENSER V1: Requested amount cannot be dispensed” ”DISPENSER V1: no cassette for the requested currency” ”DISPENSER V1: parameter is larger than 40 banknotes” ”DISPENSER V1: Electronics of the photosensor amplifier defect” ”DISPENSER V1: Unknow device configuration” ”DISPENSER V1: Photosensor L1. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 41 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO ”DISPENSER V1: Photosensor L25 does not become free” ”DISPENSER V1: Photosensor L25 is not reached” ”DISPENSER V1: Photosensor L25 is not reached” ”DISPENSER V1: Money does not reach L21” ”DISPENSER V1: Photosensor L21 does not become free” ”DISPENSER V1: Photosensor L21 does not become free” ”DISPENSER V1: Photosensor L21 not reached” ”DISPENSER V1: Photosensor L21 is not reached” ”DISPENSER V1: Correct performed retract after TIMEOUT” ”DISPENSER V1: Photosensor L26 does not become free” ”DISPENSER V1: Photosensor L26 unexpectedly covered” ”DISPENSER V1: Photosensor L26 unexpectedly covered” ”DISPENSER V1: Photosensor L26 is not reached” ”DISPENSER V1: Photosensor L26 already free before retract” ”DISPENSER V1: Correct retract performed after TIMEOUT” ”DISPENSER V1: Photosensor L27 does not become free” ”DISPENSER V1: Photosensor L27 unexpectedly covered” ”DISPENSER V1: Photosensor L26 unexpectedly covered” ”DISPENSER V1: Photosensor L27 is not reached” ”DISPENSER V1: Photosensor L27 becomes free nevertheless” ”DISPENSER V1: Photosensor L28 does not become free” ”DISPENSER V1: Photosensor L28 does not become free” ”DISPENSER V1: Photosensor L28 is not reached” ”DISPENSER V1: Photosensor L28 is not reached” ”DISPENSER V1: Photosensor L29 does not become free” ”DISPENSER V1: Photosensor L29 does not become free” ”DISPENSER V1: Photosensor L29 is not reached” ”DISPENSER V1: Photosensor L29 is not reached” ”DISPENSER V1: Photosensor L30 does not become free” ”DISPENSER V1: Photosensor L30 does not become free” ”DISPENSER V1: Photosensor L30 is not reached” ”DISPENSER V1: Photosensor L30 is not reached” ”DISPENSER V1: Photosensor L31 does not become free” ”DISPENSER V1: Photosensor L31 does not become free” ”DISPENSER V1: Photosensor L31 is not reached” ”DISPENSER V1: Photosensor L31 is not reached” ”DISPENSER V1: Photosensor L32 does not become free” ”DISPENSER V1: Photosensor L32 does not become free” ”DISPENSER V1: Photosensor L32 is not reached” ”DISPENSER V1: Photosensor L32 is not reached” ”DISPENSER V1: Photosensor L33 does not become free” ”DISPENSER V1: Photosensor L33 does not become free” ”DISPENSER V1: Photosensor L33 is not reached” ”DISPENSER V1: Photosensor L33 is not reached” ”DISPENSER V1: Photosensor L35 does not become free” ”DISPENSER V1: Photosensor L35 does not become free” ”DISPENSER V1: Photosensor L35 is not reached” ”DISPENSER V1: Photosensor L35 is not reached” ”DISPENSER V1: Photosensor G9 is not reached” ”DISPENSER V1: Photosensor G9 is not reached” ”DISPENSER V1: Photosensor G8 is not reached” ”DISPENSER V1: Photosensor G8 is not reached” ”DISPENSER V1: Invalid cassette slot” ”DISPENSER V1: Error in self-test” ”DISPENSER V1: Internal error Possible hardware error” ”DISPENSER V1: Error occurs only with coded V24 line to the CDM” ”DISPENSER V1: DLL for SW encording. could not be opened” ”DISPENSER V1: Invalid CRC received with encoded line” ”DISPENSER V1: Keyword specified in parameter block has invalid length” ”DISPENSER V1: The segment selector is invalid” U25604-J-Z745-1-7600 October 2004 381 . CSCEDSDLL.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 5F11_E 5F18_E 5F19_E 6300_E 6310_E 6311_E 6318_E 6319_E 7010_E 7011_E 7012_E 7013_E 7018_E 7019_E 7110_E 7111_E 7112_E 7113_E 7118_E 7119_E 7210_E 7211_E 7218_E 7219_E 7310_E 7311_E 7318_E 7319_E 7410_E 7411_E 7418_E 7419_E 7510_E 7511_E 7518_E 7519_E 7610_E 7611_E 7618_E 7619_E 7710_E 7711_E 7718_E 7719_E 7910_E 7911_E 7918_E 7919_E 7B10_E 7B11_E 7C10_E 7C11_E 8000_E 8001_E 8002_E 8004_E 8005_E 8006_E 8007_E 8009_E Sev. EE-PROM” ”DISPENSER V1: Clutch signal error” ”DISPENSER V1: Dispensing sensor error” ”DISPENSER V1: Evaluation electronics defect” ”DISPENSER V1: Card is not in a device” ”DISPENSER V1: Device could not be identified” ”DISPENSER V1: Job currently not allowed” ”DISPENSER V1: Job unknown” ”DISPENSER V1: Area/subarea selected does not exist” ”DISPENSER V1: No free block” ”DISPENSER V1: Area selected already exists” ”DISPENSER V1: Character cannot be written” ”DISPENSER V1: Attempt to write to a write-protected area” ”DISPENSER V1: Error during processing of the cassette EE-PROM” ”DISPENSER V1: Required area cannot be dissolved” ”DISPENSER V1: Old password incorrect” ”DISPENSER V1: Syntax error in job” ”DISPENSER V1: Cash cannot be dispensed from the selected cassette” ”DISPENSER V1: Cash cannot dispensed from cassette” ”DISPENSER V1: Hardware lock” ”DISPENSER V1: Cannot determine reference value” ”DISPENSER V1: Number of banknotes too high for reference value” ”DISPENSER V1: Not possible to determine the reference value” ”DISPENSER V1: Not possible to accumulate the data-specific pressure” ”DISPENSER V1: The transport key is missing” ”DISPENSER V1: The line key is missing” ”DISPENSER V1: The safe door is not open” ”DISPENSER V1: CODE TEST application command not possible” ”DISPENSER V1: Key test not possible. with photosensor amplifier” ”DISPENSER V1: Customer relay not connected” ”DISPENSER V1: Error when releasing the cassette” ”DISPENSER V1: Error when initiating the cassette” ”DISPENSER V1: No reject cassette” ”DISPENSER V1: There is no dispensing cassette” ”DISPENSER V1: Time-out at cassette initialization/release” ”DISPENSER V1: EE-PROM defect” ”DISPENSER V1: Main motor is not working” ”DISPENSER V1: Incorrect motor speed” ”DISPENSER V1: Hardware error (processor)” ”DISPENSER V1: Hardware error (E-PROM)” ”DISPENSER V1: Cassette busy (pressure being accumulated)” ”DISPENSER V1: Reject position cannot be reached” ”DISPENSER V1: Reject position cannot be reached” ”DISPENSER V1: Processor defect” ”DISPENSER V1: RAM defect” ”DISPENSER V1: Checksum error. with measuring station” ”DISPENSER V1: Time-out during comm. E-PROM” ”DISPENSER V1: Checksum error.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 0007 9000_E 9100_E 9200_E B000_E B100_E B200_E B300_E B400_E B510_E B511_E B512_E B513_E B514_E B523_E B530_E B531_E B534_E B535_E B536_E B537_E B538_E B539_E B544_E B545_E B546_E B547_E B548_E B600_E B700_E B800_E B900_E BA00_E BB00_E BC00_E BD00_E BE00_E C000_E C100_E C200_E C300_E C400_E C500_E C600_E D000_E D100_E D200_E D300_E D400_E D500_E D600_E Sev. because encryption is off” ”DISPENSER V1: This message occurs in the dialog” ”DISPENSER V1: This error occurs in the dialog” 382 October 2004 U25604-J-Z745-1-7600 . 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 07 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO ”DISPENSER V1: Time-out during comm. M-Status & M-Data Reference Tables CSC-W32 Error Classes Cash Dispenser NG (Classes: 0018/AA18/001D) The following table lists the M-Status and M-Data codes assigned to the device classes Cash Dispenser NG. Error codes of class "0018" are basic errors. Table 100: Cash Dispenser NG (Classes: 0018/001D)) Error Error Class Code 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 DEFA_W DEFA_E E000_W E000_E E001_W E001_E E002_W E002_E E003_W E003_E E004_W E004_E E005_W E005_E EF00_E EF01_E EF02_E EF03_E EF04_E F000_E F001_E F002_E F003_E F004_E F005_E F006_E F007_E F012_E F013_E F015_E FE06_E FE07_E FE08_E FE09_E FE0A_E FE0B_E FE0C_E FE0F_E FE13_E FE16_E FE7A_E FE7B_E FE85_E Sev. 2 4 2 2 1 1 1 1 1 1 1 0 2 2 4 1 1 1 1 1 4 2 2 2 4 2 2 4 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 19 19 34 34 09 09 09 09 00 00 05 05 09 09 09 09 09 09 09 09 09 00 09 09 11 11 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER NG: DEFAULT_WARNING" "DISPENSER NG: DEFAULT_ERROR" "DISPENSER NG: No banknotes taken by the customer" "DISPENSER NG: No banknotes taken by the customer" "DISPENSER NG: All banknotes taken by the customer" "DISPENSER NG: All banknotes taken by the customer" "DISPENSER NG: Firmware on disk is newer than SW loaded in CDMNG" "DISPENSER NG: Firmware on disk is newer than SW loaded in CDMNG" "DISPENSER NG: There is no firmware loaded in the CDM-NG" "DISPENSER NG: There is no firmware loaded in the CDM-NG" "DISPENSER NG: DH configured to switch LEDs" "DISPENSER NG: DH configured to switch LEDs" "DISPENSER NG: Handling error at the filling tray" "DISPENSER NG: Handling error at the filling tray" "DISPENSER NG: V24 data not in the expected format" "DISPENSER NG: Invalid CRC received with encrypted line" "DISPENSER NG: Wrong value for FRM_AUTO_LOAD in CSCCNG section" "DISPENSER NG: Wrong value for LED in CSCINI/Registry with CSCCNG" "DISPENSER NG: Firmware loading could not be completed" "DISPENSER NG: Firmware not loaded in CDM-NG" "DISPENSER NG: Wrong syntax" "DISPENSER NG: One of the locks is active" "DISPENSER NG: Error occured during execution of command" "DISPENSER NG: Safe door must be open for this command" "DISPENSER NG: The command cannot be executed at this point of time" "DISPENSER NG: The CDM-NG recognized a problem with the encryption" "DISPENSER NG: If no error found" "DISPENSER NG: Same error as CNG_FRM_DEVICE_NOT_READY" "DISPENSER NG: The same error as CNG_FRM_ERROR with an exception" "DISPENSER NG: The same error as CNG_FRM_CONTEXT with an exception" "DISPENSER NG: COMM reports invalid spec. Class AA18 is the USB class assigned to the Cash Dispenser device. for the protocol" "DISPENSER NG: A COMM WRITE command is cancelled by the user" "DISPENSER NG: COMM WRITE command could not be executed" "DISPENSER NG: A COMM READ command could not be executed" "DISPENSER NG: A COMM READ command is cancelled by the user" "DISPENSER NG: The COMM driver reports a parity error" "DISPENSER NG: The COMM driver reports a general error" "DISPENSER NG: Peripheral device did not answer" "DISPENSER NG: The channel was not initialized" "DISPENSER NG: The COMM driver reports a break" "DISPENSER NG: The COMM driver reports a overrun error" "DISPENSER NG: The COMM driver reports a frameing error" "DISPENSER NG: The COMM driver could not be opened" U25604-J-Z745-1-7600 October 2004 383 . Error codes of class "001D" are extended errors. device excceeded" "DISPENSER NG: The protocol was cancelled" "DISPENSER NG: The length in TxData is 0" "DISPENSER NG: CSCWISODLL could not be found in the PATH" "DISPENSER NG: The CSCWISODLL could not be opened" "DISPENSER NG: The peripheral device did not answer" "DISPENSER NG: Peripheral device did not answer as expected" "DISPENSER NG: The peripheral device is busy" "DISPENSER NG: Peripheral device did not answer as expected" "DISPENSER NG: Max no.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 0018 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 FE89_E FE8B_E FE8C_E FE8D_E FE8E_E FE8F_E FE90_E FE91_E FE92_E FE93_E FE94_E FE95_E FE96_E FE97_E FE98_E FE9C_E FE9D_E FE9E_E FEE0_E FEE1_E FEE2_E FEE3_E FEE4_E FEE5_E FEE6_E FEE7_E FEE8_E FEE9_E FEEA_E FEEB_E FEEC_E FEED_E FEEF_E FEF0_E FEF1_E FEF2_E FEF3_E FEF4_E FEF5_E DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E Sev. error is reported by the USB host controller" "USB/CDM: USB device is not responding. of repeat transmissions reached" "DISPENSER NG: Device asked for termination" "DISPENSER NG: Peripheral device did not answer" "DISPENSER NG: Response of device not completely received" "DISPENSER NG: The header of the response is invalid" "DISPENSER NG: DID does not agree with the transmitted DID" "DISPENSER NG: DID does not agree with the transmitted device ID" "DISPENSER NG: Command spec. does not agree with the transmitted command spec." "DISPENSER NG: The response of the device has not been completely received" "DISPENSER NG: A cancel command has been called" "DISPENSER NG: A cancel command has been called" "DISPENSER NG: The command could not be executed" "DISPENSER NG: The command was aborted by the user" "DISPENSER NG: The command could not be executed" "DISPENSER NG: A cancel command could not be executed" "DISPENSER NG: Internal monitoring time exceeded" "DISPENSER NG: Internal error within the CSCWISODLL" "USB/CDM: DEFAULT_WARNING" "USB/CDM: DEFAULT_ERROR" "USB/CDM: Unexpected descriptor was reported from USB device" "USB/CDM: Device not found" "USB/CDM: Not enough memory available" "USB/CDM: It was no endpoint found in the descriptor" "USB/CDM: The creation of the list of USB devices failed" "USB/CDM: USB read command could not be executed in the specified monitoring time" "USB/CDM: USB READ command is cancelled by the user" "USB/CDM: The pointer pData is illegal" "USB/CDM: The length in DataSize is 0 (zero)" "USB/CDM: CRC error has been detected" "USB/CDM: Bit stuffing error has been detected" "USB/CDM: DATA toggle mismatch has been detected" "USB/CDM: STALLPID has been detected. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER NG: The pointer pTxData is illegal" "DISPENSER NG: Called function is invalid for CscCommOpen" "DISPENSER NG: The peripheral device does not return an STX" "DISPENSER NG: The peripheral device does not return an ETX" "DISPENSER NG: Block length does not agree with the transmitted block length" "DISPENSER NG: The block ID is invalid" "DISPENSER NG: Received DID does not agree with the transmitted DID" "DISPENSER NG: Wrong command specification" "DISPENSER NG: The received acknowledge type is invalid" "DISPENSER NG: Max no of repeat transmissions reached" "DISPENSER NG: Max no of receive repeats has been reached" "DISPENSER NG: Monitoring time during transmission has been exceeded" "DISPENSER NG: Monitoring time during receive has been exceeded" "DISPENSER NG: Busy time from phys. error is reported by the USB host" 384 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB host" "USB/CDM: Endpoint has been halted by the USB bus driver USBD" "USB/CDM: Memory allocation attempt has failed. error is reported by the USBIO driver" "USB/CDM: Either the handle is already bound to a pipe" "USB/CDM: Handle is not bound to a pipe. error is reported by the USB bus" "USB/CDM: There is not enough bandwidth available. error is reported by the USB host" "USB/CDM: Data underrun error detected. error is reported by the USB bus" "USB/CDM: There are data transfer requests pending for the device" "USB/CDM: Request has failed. error is reported by the USB bus driver" "USB/CDM: Invalid configuration descriptor was reported by the device" "USB/CDM: Operation has failed. error is reported by the USB" "USB/CDM: Operation is not supported. error is reported by the USB host controller" "USB/CDM: Unexpected PID detected. error is reported by the USB host" "USB/CDM: FIFO error has been detected. error is reported by the USB host" "USB/CDM: Error code is reserved by the USB host controller driver" "USB/CDM: Error code is reserved by the USB host controller driver" "USB/CDM: Buffer overrun has been detected. error is reported by the USBIO driver" "USB/CDM: Invalid input buffer has been passed to an IOCTL operation" "USB/CDM: Invalid output buffer has been passed to an IOCTL operation" "USB/CDM: There is not enough system memory available to complete the operation" "USB/CDM: There are read or write requests pending. error is reported by the USB host" "USB/CDM: Buffer underrun has been detected. error is reported by the USB bus driver" "USB/CDM: USB frame control is currently owned. error is reported by the USBIO driver" "USB/CDM: USB device has been removed from the system" "USB/CDM: Specified control code is not supported" U25604-J-Z745-1-7600 October 2004 385 . error is reported by the USBIO driver" "USB/CDM: There are open pipes. error is reported by the USB bus" "USB/CDM: Internal host controller error has been detected" "USB/CDM: Short transfer has been detected. PCI bus latency was too long" "USB/CDM: XACT error has been detected. error is reported by the USBIO" "USB/CDM: USB device is already configured. error is reported by the USB bus" "USB/CDM: Invalid URB function code has been passed.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E Sev. error is reported by the USB host" "USB/CDM: Device is babbling. error is reported by the USB bus" "USB/CDM: Asynchronous request has failed. error is reported by the USB bus" "USB/CDM: Bad start frame has been specified. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "USB/CDM: PID check has failed. error is reported by the USB bus" "USB/CDM: USB frame control is currently not owned. error is reported by the USB host" "USB/CDM: Buffer was not accessed. error is reported by the USB" "USB/CDM: Invalid parameter has been passed. data transfer phase exceeds the USB frame length" "USB/CDM: Data buffer error has been detected. error is reported by the USBIO" "USB/CDM: The USB device is not configured. error is reported by the USB host" "USB/CDM: Data overrun error detected. error is reported by the USB bus driver USBD" "USB/CDM: Invalid pipe handle has been passed. This error is reported by the USBIO driver" "USB/CDM: The specified pipe was not found in the current configuration" "USB/CDM: An invalid asynchronous data packet has been specified" "USB/CDM: There are not enough system resources to complete the operation" "USB/CDM: Specified interface was not found in the current configuration" "USB/CDM: Operation cannot be executed while the USB device is in the current state" "USB/CDM: Invalid parameter has been specified with an IOCTL operation" "USB/CDM: Evaluation interval of the USBIO DEMO version has expired" "USB/CDM: Invalid power state has been specified" "USB/CDM: Device has entered a power down state" "USB/CDM: API version reported by the USBIO driver does not match" "USB/CDM: Set configuration operation has failed.dll could not be loaded" "USB/CDM: Set configuration request has failed" "USB/CDM: Buffer is too small. error is reported by the USBIO driver" "USB/CDM: Invalid recipient has been specified" "USB/CDM: Either an invalid request type has been specified" "USB/CDM: Invalid IOCTL code has been specified.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 AA18 001D 001D 001D 001D 001D 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E 1083_E 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E DEFA_W DEFA_E 1000_E 1001_E 1010_E Sev. CDM has received an invalid command" "DISPENSER FL: No response from the CDM" "DISPENSER FL: CDM electronics faulty" 386 October 2004 U25604-J-Z745-1-7600 . error is reported by the USBIO" "USB/CDM: Direction of the data transfer request is not supported by that pipe" "USB/CDM: Number of asynchronous data packets specified in an asynchronous read" "USB/CDM: Memory resources are exhausted. error is reported by the USB bus driver USBD" "DISPENSER NG: DEFAULT_WARNING" "DISPENSER NG: DEFAULT_ERROR" "DISPENSER FL: Context error. error is reported by the USBIO" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CDM: The specified device object does not exist" "USB/CDM: Device object was opened. error is reported by the USB bus driver" "USB/CDM: USB device is gone. error is reported by the USB bus driver USBD" "USB/CDM: Interface was not found. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 2 4 2 4 4 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 13 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 1000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "USB/CDM: Operation has been timed out. error is reported by the USB bus driver USBD" "USB/CDM: Invalid pipe flags have been specified" "USB/CDM: Operation has been timed out. there is no valid handle to execute the operation" "USB/CDM: Enumeration of the specified devices has failed" "USB/CDM: Invalid parameter has been passed to a function" "USB/CDM: Library setupapi. M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 1011_E 1012_E 1013_E 1014_E 1018_E 1019_E 1020_E 1021_E 1022_E 1023_E 1024_E 1025_E 1026_E 1028_E 1029_E 1031_E 1032_E 1033_E 1034_E 1035_E 1036_E 1041_E 1042_E 1043_E 1044_E 1045_E 1046_E 1051_E 1052_E 1053_E 1054_E 1055_E 1056_E 1061_E 1062_E 1063_E 1064_E 1065_E 1066_E 1070_E 1071_E 1072_E 1073_E 1074_E 1075_E 1076_E 1081_E 1082_E 1083_E 1084_E 1085_E 1086_E 1090_E 1091_E 1093_E 1098_E 1099_E 1800_E 1801_E 1805_E 1806_E 1807_E Sev. CDM has received an invalid command" "DISPENSER V4: No response from CDM" "DISPENSER V4: Communication problem with the chip card controller" "DISPENSER V4: Communication problem with the chip card" "DISPENSER V4: Hardware configuration not accepted" U25604-J-Z745-1-7600 October 2004 387 ." "DISPENSER FL: Note jam during dispensing" "DISPENSER FL: Money jam in the output transport" "DISPENSER FL: Single reject switch faulty/blocked" "DISPENSER FL: Measuring station faulty" "DISPENSER FL: Photosensor amplifier faulty" "DISPENSER FL: Bundle reject switch faulty" "DISPENSER FL: Reject/retract drive faulty/blocked" "DISPENSER FL: Dispensing drive faulty" "DISPENSER FL: Collecting tray defect" "DISPENSER FL: Money slot/shutter jammed or cannot be opened" "DISPENSER FL: Manipulation during delivery" "DISPENSER FL: Too many bundle rejects (cassette 1)" "DISPENSER FL: Too many bundle rejects (cassette 2)" "DISPENSER FL: Too many bundle rejects (cassette 3)" "DISPENSER FL: Too many bundle rejects (cassette 4)" "DISPENSER FL: Too many bundle rejects (cassette 5)" "DISPENSER FL: Too many bundle rejects (cassette 6)" "DISPENSER FL: Note extraction impossible (cassette 1)" "DISPENSER FL: Note extraction impossible (cassette 2)" "DISPENSER FL: Note extraction impossible (cassette 3)" "DISPENSER FL: Note extraction impossible (cassette 4)" "DISPENSER FL: Note extraction impossible (cassette 5)" "DISPENSER FL: Note extraction impossible (cassette 6)" "DISPENSER FL: Too many bad notes (cassette 1)" "DISPENSER FL: Too many bad notes (cassette 2)" "DISPENSER FL: Too many bad notes (cassette 3)" "DISPENSER FL: Too many bad notes (cassette 4)" "DISPENSER FL: Too many bad notes (cassette 5)" "DISPENSER FL: Too many bad notes (cassette 6)" "DISPENSER FL: EE-PROM error (cassette 1)" "DISPENSER FL: EE-PROM error (cassette 2)" "DISPENSER FL: EE-PROM error (cassette 3)" "DISPENSER FL: EE-PROM error (cassette 4)" "DISPENSER FL: EE-PROM error (cassette 5)" "DISPENSER FL: EE-PROM error (cassette 6)" "DISPENSER FL: Photosensor measuring station soiled" "DISPENSER FL: Dispenser sensor soiled (cassette 1)" "DISPENSER FL: Dispenser sensor soiled (cassette 2)" "DISPENSER FL: Dispenser sensor soiled (cassette 3)" "DISPENSER FL: Dispenser sensor soiled (cassette 4)" "DISPENSER FL: Dispenser sensor soiled (cassette 5)" "DISPENSER FL: Dispenser sensor soiled (cassette 6)" "DISPENSER FL: Empty sensor soiled (cassette 1)" "DISPENSER FL: Empty sensor soiled (cassette 2)" "DISPENSER FL: Empty sensor soiled (cassette 3)" "DISPENSER FL: Empty sensor soiled (cassette 4)" "DISPENSER FL: Empty sensor soiled (cassette 5)" "DISPENSER FL: Empty sensor soiled (cassette 6)" "DISPENSER FL: Photosensor L1 soiled" "DISPENSER FL: Photosensor L18 soiled" "DISPENSER FL: Photosensor L21 soiled" "DISPENSER FL: Photosensor L27 soiled" "DISPENSER FL: Photosensor L28 soiled" "DISPENSER V4: Context error. 4 4 4 4 2 2 4 4 4 4 4 2 2 2 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 MStatus 09 09 00 10 03 12 18 05 05 11 07 09 05 05 13 02 02 02 02 02 02 03 03 03 03 03 03 02 02 02 02 02 02 09 09 09 09 09 09 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 01100000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER FL: No firmware in CDM" "DISPENSER FL: CDM not completely inserted" "DISPENSER FL: Max number of retracts reached" "DISPENSER FL: Minimum configuration not reached. 4 4 4 4 4 4 4 2 2 2 4 4 4 4 4 4 4 3 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 05 05 05 05 05 00 10 09 03 09 05 05 05 05 05 05 05 13 13 02 02 02 02 02 02 03 03 03 03 03 03 02 02 02 02 02 02 09 09 09 09 09 09 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 01100000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER V4: Communication problem with the EE-PROM collector" "DISPENSER V4: Service switch open.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 1808_E 1809_E 1810_E 1811_E 1812_E 1813_E 1814_E 1817_E 1818_E 1819_E 1820_E 1821_E 1822_E 1823_E 1824_E 1825_E 1826_E 1828_E 1829_E 1831_E 1832_E 1833_E 1834_E 1835_E 1836_E 1841_E 1842_E 1843_E 1844_E 1845_E 1846_E 1851_E 1852_E 1853_E 1854_E 1855_E 1856_E 1861_E 1862_E 1863_E 1864_E 1865_E 1866_E 1870_E 1871_E 1872_E 1873_E 1874_E 1875_E 1876_E 1881_E 1882_E 1883_E 1884_E 1885_E 1886_E 1890_E 1891_E 1893_E 1895_E 1898_E Sev. please insert CDM-V4 completely" "DISPENSER V4: CMD electronics faulty" "DISPENSER V4: Software missing in the CMD" "DISPENSER V4: CMD has not been inserted completely" "DISPENSER V4: The maximal number of retracts has been reached" "DISPENSER V4: Minimum configuration missing" "DISPENSER V4: Gripper belt drive faulty" "DISPENSER V4: Note jam during dispensing" "DISPENSER V4: Gripper transport defective or blocked" "DISPENSER V4: Single reject switch faulty/blocked" "DISPENSER V4: Measuring station faulty" "DISPENSER V4: Photosensor amplifier faulty" "DISPENSER V4: Circle switch faulty/blocked" "DISPENSER V4: Reject/retract drive faulty/blocked" "DISPENSER V4: Dispensing drive faulty/blocked" "DISPENSER V4: Stacker drive faulty /blocked" "DISPENSER V4: Money slot/shutter jammed or cannot be opened" "DISPENSER V4: Manipulation during delivery" "DISPENSER V4: Too many bundle rejects (cassette 1)" "DISPENSER V4: Too many bundle rejects (cassette 2)" "DISPENSER V4: Too many bundle rejects (cassette 3)" "DISPENSER V4: Too many bundle rejects (cassette 4)" "DISPENSER V4: Too many bundle rejects (cassette 5)" "DISPENSER V4: Too many bundle rejects (cassette 6)" "DISPENSER V4: Note extraction impossible (cassette 1)" "DISPENSER V4: Note extraction impossible (cassette 2)" "DISPENSER V4: Note extraction impossible (cassette 3)" "DISPENSER V4: Note extraction impossible (cassette 4)" "DISPENSER V4: Note extraction impossible (cassette 5)" "DISPENSER V4: Note extraction impossible (cassette 6)" "DISPENSER V4: Too many bad notes (cassette 1)" "DISPENSER V4: Too many bad notes (cassette 2)" "DISPENSER V4: Too many bad notes (cassette 3)" "DISPENSER V4: Too many bad notes (cassette 4)" "DISPENSER V4: Too many bad notes (cassette 5)" "DISPENSER V4: Too many bad notes (cassette 6)" "DISPENSER V4: Cassette 1 faulty" "DISPENSER V4: Cassette 2 faulty" "DISPENSER V4: Cassette 3 faulty" "DISPENSER V4: Cassette 4 faulty" "DISPENSER V4: Cassette 5 faulty" "DISPENSER V4: Cassette 6 faulty" "DISPENSER V4: Photosensors measuring station soiled" "DISPENSER V4: Dispenser sensor soiled (cassette 1)" "DISPENSER V4: Dispenser sensor soiled (cassette 2)" "DISPENSER V4: Dispenser sensor soiled (cassette 3)" "DISPENSER V4: Dispenser sensor soiled (cassette 4)" "DISPENSER V4: Dispenser sensor soiled (cassette 5)" "DISPENSER V4: Dispenser sensor soiled (cassette 6)" "DISPENSER V4: Empty sensor soiled (cassette 1)" "DISPENSER V4: Empty sensor soiled (cassette 2)" "DISPENSER V4: Empty sensor soiled (cassette 3)" "DISPENSER V4: Empty sensor soiled (cassette 4)" "DISPENSER V4: Empty sensor soiled (cassette 5)" "DISPENSER V4: Empty sensor soiled (cassette 6)" "DISPENSER V4: Photosensor L1 soiled" "DISPENSER V4: Photosensor L18 soiled" "DISPENSER V4: Control tray single reject L2 soiled" "DISPENSER V4: Money taken light barrier L26/L27 soiled" "DISPENSER V4: Withdrawal photosensor L27 soiled" 388 October 2004 U25604-J-Z745-1-7600 . 2 2 2 2 4 4 4 4 4 2 2 4 4 2 2 2 4 2 4 4 2 3 3 4 2 2 2 2 3 2 2 2 2 2 2 2 2 2 3 2 2 2 2 2 2 2 2 2 2 2 2 2 4 2 2 2 4 2 2 2 MStatus 05 05 05 05 09 09 09 09 00 03 05 05 05 03 03 05 07 12 12 07 12 13 14 07 18 18 18 13 18 13 01 04 13 30 13 40 18 30 18 18 18 18 05 18 13 10 18 13 02 14 41 18 03 18 01 19 29 04 01 04 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 01100000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER V4: Output photosensor L28 soiled" "DISPENSER V4: Light barrier of bundle back edge control (presenter) soiled" "DISPENSER V4: Light barrier L2 of reject bin soiled" "DISPENSER V4: Light barrier L3 of reject bin soiled" "DISPENSER NG: No response from the CDM" "DISPENSER NG: CDM electronics faulty" "DISPENSER NG: Software missing in the CDM" "DISPENSER NG: CDM has not been inserted completely" "DISPENSER NG: Max number of retracts reached" "DISPENSER NG: Note jam during dispensing" "DISPENSER NG: Single reject switch faulty/blocked" "DISPENSER NG: Measuring station faulty" "DISPENSER NG: Photosensor amplifier faulty" "DISPENSER NG: Dispensing drive faulty/blocked" "DISPENSER NG: Switching dispensing/transport" "DISPENSER NG: Cassette unknown.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 1899_E 189A_E 189D_E 189E_E 4001_E 4010_E 4011_E 4012_E 4013_E 4018_E 4020_E 4021_E 4022_E 4025_E 4026_E 4100_E 4114_E 4119_E 4123_E 4124_E 4128_E 4129_E 4200_E 4214_E 4219_E 4223_E 4224_E 4228_E 4229_E 4300_E 4314_E 4319_E 4328_E 4329_E 4400_E 4414_E 4419_E 4428_E 4429_E 4500_E 4519_E 4529_E 4600_E 4619_E 4629_E 4700_E 4719_E 4729_E 4800_E 4829_E 4900_E 4919_E 4A00_E 4A19_E 4B00_E 4B19_E 4C19_E 4D00_E 4E00_E 4F00_E Sev. reinserted" "DISPENSER NG: Reject cassette missing" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Bundle reject switch faulty/blocked" "DISPENSER NG: Reject/retract drive faulty/blocked" "DISPENSER NG: Shutter cannot be opened/defect" "DISPENSER NG: Manipulation during delivery" "DISPENSER NG: Shutter has been blocked" "DISPENSER NG: Reject cassette not logged on" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Bundle reject switch faulty/blocked" "DISPENSER NG: Reject/retract drive faulty/blocked" "DISPENSER NG: Shutter undefined" "DISPENSER NG: Manipulation in withdrawal position" "DISPENSER NG: Command cannot be executed while Shutter open" "DISPENSER NG: Cash-out cassette(s) missing" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Shutter cannot be closed/undefined" "DISPENSER NG: Manipulation during retract" "DISPENSER NG: Command cannot be executed while Shutter undefined" "DISPENSER NG: No cash-out cassette(s) logged on" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Shutter undefined during retract" "DISPENSER NG: Manipulation during delivery" "DISPENSER NG: Manipulation at cash-out photosensor" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Manipulation during delivery" "DISPENSER NG: Note paths blocked" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Manipulation in withdrawal position" "DISPENSER NG: Max number of retracts reached" "DISPENSER NG: Money jam in the output transport" "DISPENSER NG: Manipulation during retract" "DISPENSER NG: Single reject switch faulty" "DISPENSER NG: Manipulation during delivery" "DISPENSER NG: Self-test activated" "DISPENSER NG: Photosensor covered during withdrawal" "DISPENSER NG: The jam was not eliminated effectively" "DISPENSER NG: Photosensor covered during withdrawal" "DISPENSER NG: Cash-out cassette missing" "DISPENSER NG: Photosensor covered during retract" "DISPENSER NG: Motor defect" "DISPENSER NG: Cassette is empty" "DISPENSER NG: Cassette or dispensing sensor defect" "DISPENSER NG: Cassette becomes empty during dispensing procedure" U25604-J-Z745-1-7600 October 2004 389 . missing. CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 8031_E 8032_E 8033_E 8034_E 8035_E 8036_E 8041_E 8042_E 8043_E 8044_E 8045_E 8046_E 8061_E 8062_E 8063_E 8064_E 8065_E 8066_E 8070_E 8071_E 8072_E 8073_E 8074_E 8075_E 8076_E 8081_E 8082_E 8083_E 8084_E 8085_E 8086_E 8090_E 8091_E 8092_E 8093_E 8094_E 8095_E 8096_E 8097_E 8098_E 8099_E 809A_E 809B_E 809C_E 8151_E 8152_E 8153_E 8154_E 8155_E 8156_E 8251_E 8252_E 8253_E 8254_E 8255_E 8256_E 8300_E 8312_E 8313_E 8314_E 8315_E 8316_E Sev. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 02 02 02 02 02 02 03 10 10 10 10 10 09 09 09 09 09 09 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 02 02 02 02 02 02 02 02 02 02 02 02 11 09 11 11 11 11 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER NG: Too many bundle rejects (cassette 1)" "DISPENSER NG: Too many bundle rejects (cassette 2)" "DISPENSER NG: Too many bundle rejects (cassette 3)" "DISPENSER NG: Too many bundle rejects (cassette 4)" "DISPENSER NG: Too many bundle rejects (cassette 5)" "DISPENSER NG: Too many bundle rejects (cassette 6)" "DISPENSER NG: Note extraction impossible (cassette 1)" "DISPENSER NG: Note extraction impossible (cassette 2)" "DISPENSER NG: Note extraction impossible (cassette 3)" "DISPENSER NG: Note extraction impossible (cassette 4)" "DISPENSER NG: Note extraction impossible (cassette 5)" "DISPENSER NG: Note extraction impossible (cassette 6)" "DISPENSER NG: Cassette 1 faulty" "DISPENSER NG: Cassette 2 faulty" "DISPENSER NG: Cassette 3 faulty" "DISPENSER NG: Cassette 4 faulty" "DISPENSER NG: Cassette 5 faulty" "DISPENSER NG: Cassette 6 faulty" "DISPENSER NG: Photosensor measuring station soiled" "DISPENSER NG: Dispenser sensor soiled (cassette 1)" "DISPENSER NG: Dispenser sensor soiled (cassette 2)" "DISPENSER NG: Dispenser sensor soiled (cassette 3)" "DISPENSER NG: Dispenser sensor soiled (cassette 4)" "DISPENSER NG: Dispenser sensor soiled (cassette 5)" "DISPENSER NG: Dispenser sensor soiled (cassette 6)" "DISPENSER NG: Empty sensor soiled (cassette 1)" "DISPENSER NG: Empty sensor soiled (cassette 2)" "DISPENSER NG: Empty sensor soiled (cassette 3)" "DISPENSER NG: Empty sensor soiled (cassette 4)" "DISPENSER NG: Empty sensor soiled (cassette 5)" "DISPENSER NG: Empty sensor soiled (cassette 6)" "DISPENSER NG: Photosensor L1 soiled" "DISPENSER NG: Photosensor L18 soiled" "DISPENSER NG: Photosensor L19 soiled" "DISPENSER NG: Photosensor L21 soiled" "DISPENSER NG: Photosensor L22 soiled" "DISPENSER NG: Photosensor L26 soiled" "DISPENSER NG: Photosensor L33 soiled" "DISPENSER NG: Photosensor L35 soiled" "DISPENSER NG: Photosensor L27 soiled" "DISPENSER NG: Photosensor L28 soiled" "DISPENSER NG: Photosensor L29 soiled" "DISPENSER NG: Photosensor L36 soiled" "DISPENSER NG: Photosensor L37 soiled" "DISPENSER NG: Too many double notes (cassette 1)" "DISPENSER NG: Too many double notes (cassette 2)" "DISPENSER NG: Too many double notes (cassette 3)" "DISPENSER NG: Too many double notes (cassette 4)" "DISPENSER NG: Too many double notes (cassette 5)" "DISPENSER NG: Too many double notes (cassette 6)" "DISPENSER NG: Too many bad notes (cassette 1)" "DISPENSER NG: Too many bad notes (cassette 2)" "DISPENSER NG: Too many bad notes (cassette 3)" "DISPENSER NG: Too many bad notes (cassette 4)" "DISPENSER NG: Too many bad notes (cassette 5)" "DISPENSER NG: Too many bad notes (cassette 6)" "DISPENSER NG: Bills left in stacker after output to diverter" "DISPENSER NG: CDM has not been inserted completely" "DISPENSER NG: Cash left in diverter after reset/booting" "DISPENSER NG: Dispensing not possible" "DISPENSER NG: Command could not be executed" "DISPENSER NG: Command could not be executed" 390 October 2004 U25604-J-Z745-1-7600 . 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 11 11 11 05 05 11 11 11 11 05 05 02 02 02 02 02 02 11 11 11 11 11 11 02 02 02 02 02 02 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER NG: Note jam during dispense operation" "DISPENSER NG: Note jam in the output transport" "DISPENSER NG: Single reject switch faulty/blocked" "DISPENSER NG: Measuring station faulty" "DISPENSER NG: Photosensor amplifier faulty" "DISPENSER NG: Bundle reject switch faulty/blocked" "DISPENSER NG: Reject/retract drive faulty/blocked" "DISPENSER NG: Dispensing drive faulty/blocked" "DISPENSER NG: Switching dispensing/transport faulty" "DISPENSER NG: Diverter does not reach the end position" "DISPENSER NG: Bills jammed in stacker.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 001D 8318_E 8319_E 8320_E 8321_E 8322_E 8323_E 8324_E 8325_E 8326_E 8328_E 8329_E 8331_E 8332_E 8333_E 8334_E 8335_E 8336_E 8341_E 8342_E 8343_E 8344_E 8345_E 8346_E 8351_E 8352_E 8353_E 8354_E 8355_E 8356_E 8361_E 8362_E 8363_E 8364_E 8365_E 8366_E 8370_E 8371_E 8372_E 8373_E 8374_E 8375_E 8376_E 8381_E 8382_E 8383_E 8384_E 8385_E 8386_E 8390_E 8391_E 8392_E 8393_E 8394_E 8395_E 8396_E 8397_E 8398_E 8399_E 839A_E 839B_E 839C_E 8400_E Sev. under output photosensor" "DISPENSER NG: Too many bundle rejects (casette 1)" "DISPENSER NG: Too many bundle rejects (casette 2)" "DISPENSER NG: Too many bundle rejects (casette 3)" "DISPENSER NG: Too many bundle rejects (casette 4)" "DISPENSER NG: Too many bundle rejects (casette 5)" "DISPENSER NG: Too many bundle rejects (casette 6)" "DISPENSER NG: Note extraction impossible (cassette 1)" "DISPENSER NG: Note extraction impossible (cassette 2)" "DISPENSER NG: Note extraction impossible (cassette 3)" "DISPENSER NG: Note extraction impossible (cassette 4)" "DISPENSER NG: Note extraction impossible (cassette 5)" "DISPENSER NG: Note extraction impossible (cassette 6)" "DISPENSER NG: Too many double notes (cassette 1)" "DISPENSER NG: Too many double notes (cassette 2)" "DISPENSER NG: Too many double notes (cassette 3)" "DISPENSER NG: Too many double notes (cassette 4)" "DISPENSER NG: Too many double notes (cassette 5)" "DISPENSER NG: Too many double notes (cassette 6)" "DISPENSER NG: Cassette 1 faulty" "DISPENSER NG: Cassette 2 faulty" "DISPENSER NG: Cassette 3 faulty" "DISPENSER NG: Cassette 4 faulty" "DISPENSER NG: Cassette 5 faulty" "DISPENSER NG: Cassette 6 faulty" "DISPENSER NG: Photosensors measuring station soiled" "DISPENSER NG: Dispenser sensor soiled (cassette 1)" "DISPENSER NG: Dispenser sensor soiled (cassette 2)" "DISPENSER NG: Dispenser sensor soiled (cassette 3)" "DISPENSER NG: Dispenser sensor soiled (cassette 4)" "DISPENSER NG: Dispenser sensor soiled (cassette 5)" "DISPENSER NG: Dispenser sensor soiled (cassette 6)" "DISPENSER NG: Empty sensor soiled (cassette 1)" "DISPENSER NG: Empty sensor soiled (cassette 2)" "DISPENSER NG: Empty sensor soiled (cassette 3)" "DISPENSER NG: Empty sensor soiled (cassette 4)" "DISPENSER NG: Empty sensor soiled (cassette 5)" "DISPENSER NG: Empty sensor soiled (cassette 6)" "DISPENSER NG: Photosensor L1 soiled" "DISPENSER NG: Photosensor L18 soiled" "DISPENSER NG: Photosensor L19 soiled" "DISPENSER NG: Photosensor L21 soiled" "DISPENSER NG: Photosensor L22 soiled" "DISPENSER NG: Photosensor L26 soiled" "DISPENSER NG: Photosensor L33 soiled" "DISPENSER NG: Photosensor L35 soiled" "DISPENSER NG: Photosensor L27 soiled" "DISPENSER NG: Photosensor L28 soiled" "DISPENSER NG: Photosensor L29 soiled" "DISPENSER NG: Photosensor L36 soiled" "DISPENSER NG: Photosensor L37 soiled" "DISPENSER NG: Banknotes left in the stacker after output" U25604-J-Z745-1-7600 October 2004 391 . Class BB1A is class IEEE 1394 assigned to device class CashInFW. Table 101: Cash Cheque Deposit Module (CCDM) (Classes: 001A/XX1A) Error Class 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A Error Code DEFA_E DEFA_W 0014_E 0015_E 0016_E 0017_E 0018_E 001E_E 0028_E 0029_E 002A_E 002B_E 002C_E 002D_E 002F_E 0030_E 0031_E 003D_E 003E_E 003F_E 0040_E 0041_E 0042_E 0043_E 0044_E 0045_E 0046_E 0047_E 0048_E 0049_E 004A_E 004B_E Sev. Class DDA is class USB assigned to device class ChequeInFW.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 001D 001D 001D 001D 001D 001D 001D 8419_E A000_E A100_E A200_E FE38_E FE50_E FFFF_E Sev. Class AA1A is the class IEEE 1394 assigned to device class ChequeInFW. Class CC1A is class USB assigned to device class CashInFW. 2 2 2 2 4 4 2 MStatus 05 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DISPENSER NG: Note jam in the output transport" "DISPENSER NG: Wrong command" "DISPENSER NG: Wrong command" "DISPENSER NG: Programming error" "DISPENSER NG: Communication problem" "DISPENSER NG: Communication problem" "DISPENSER NG: Extended error code not computed" Cash Cheque Deposit Module (Classes: 001A/XX1A) The following table lists the MDS Status codes assigned to the device classes Cash Cheque Deposit Module (CCDM). 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "CCDM: DEFAULT ERROR" "CCDM: DEFAULT WARNING" "CCDM: General firmware error" "CCDM: Battery on controller board empty" "CCDM: Safety switch active" "CCDM: System interface does not fetch the data from the CCDM fast enough" "CCDM: Invalid or missing configuration" "CCDM: Error magnetic character reader" "CCDM: Error cheque/cash reader" "CCDM: Firmware error cheque/cash reader" "CCDM: Communication problem cheque/cash reader" "CCDM: Data error cheque/cash reader" "CCDM: Note table configuration not Ok" "CCDM: External light in cheque/cash reader" "CCDM: Communication problems (time out)" "CCDM: Communication problems" "CCDM: Cheque/cash reader firmware and CCDM firmware are incompatible" "CCDM: Error photosensor VLS" "CCDM: Error photosensor VLS" "CCDM: Error photosensor VLS" "CCDM: Error photosensor VLS" "CCDM: Error photosensor VLS1" "CCDM: Error photosensor ALS" "CCDM: Error photosensor ALS" "CCDM: Error photosensor ALS" "CCDM: Error photosensor ALS" "CCDM: Error photosensor SLS" "CCDM: Error photosensor SLS" "CCDM: Error photosensor ELS" "CCDM: Error photosensor RLS" "CCDM: Error photosensor RLS" "CCDM: Error photosensor VLS1" 392 October 2004 U25604-J-Z745-1-7600 . Media do not reached VLS" "CCDM: Clearing error I/O tray. Media jam in the intermediary transport" "CCDM: Media jam in reject transport area" "CCDM: Initialization error hinged transport 1 and/or 2" "CCDM: Position error hingend transport 1. Media jam in the separation area of the dispense" "CCDM: Clearing error I/O tray. Media jam in the intermediary transport" "CCDM: Clearing error I/O tray. The end position is not reached" "CCDM: Initialization error during setting the bundle width" "CCDM: Error on the cam disk" "CCDM: Error on the cam disk" "CCDM: Shutter cannot be opened/closed. Media did not passed VLS2" "CCDM: Media in front oaf ALS1 or ALS1 defect" "CCDM: ALS1: medium is expected but no media is coming" "CCDM: ALS1: media too long (media do not pass the drum)" "CCDM: ALS1: media is complete recognized but is too long" "CCDM: ALS1: media jam in the drum" "CCDM: ALS1: Media end is not detected during entering the drum" "CCDM: ALS1: Media end do not detected during leaving the drum" "CCDM: Media jam in sensor transport at the 3-way deflector" "CCDM: Media jam in sensor transport at the reject deflector" "CCDM: SLS3: unexpected media during transport from the alignment module" "CCDM: SLS3: unexpected media during transport from the escrow module" "CCDM: SLS3: media jam in sensor transport" "CCDM: SLS1: medium is expected but no media is coming" "CCDM: SLS1: unexpected document during transport from the alignment module" "CCDM: SLS1: unexpected document during transport from the escrow module" "CCDM: Document jam in area -> document deflector -> escrow/reject module" "CCDM: Cheque/cash reader: unexpected media during transport from the alignment module" "CCDM: Document jam at the escrow module ELS1" "CCDM: Document jam between sensor module and cassette/reject module" "CCDM: Document jam between sensor transport and reject transport" U25604-J-Z745-1-7600 October 2004 393 . The end position is not reached" "CCDM: Position error hinged transport 2. Media jam in the intermediary transport" "CCDM: Clearing error I/O tray. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "CCDM: Error photosensor ELS" "CCDM: Error photosensor KLS" "CCDM: Error photosensor KLS" "CCDM: Error photosensor KLS" "CCDM: Error photosensor KLS1" "CCDM: Transport error detected before dispensing" "CCDM: VLS6: media too long (media do not pass (VLS6)" "CCDM: VLS7: medium is expected but no media is coming" "CCDM: VLS7: media do not leave VLS7" "CCDM: VLS6: media do not leave VLS6" "CCDM: Faulty extraction detected during dispensing process" "CCDM: Clearing error I/O tray. Media jam in the I/O transport" "CCDM: Clearing error I/O tray." "CCDM: Error on metal detection module" "CCDM: VHS1: hardware error thickness measuring station" "CCDM: VHS1: hardware error thickness measuring station" "CCDM: Initialization error of reject transport" "CCDM: Media jam in reject transport area" "CCDM: Clearing error storage transport.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A Error Code 004C_E 0050_E 0051_E 0052_E 0053_E 0064_E 0066_E 0067_E 0069_E 006A_E 006C_E 006E_E 006F_E 0070_E 0071_E 0072_E 0073_E 0074_E 0078_E 0079_E 007A_E 0082_E 008C_E 008D_E 0090_E 0091_E 0096_E 0097_E 00AA_E 00B4_E 00B5_E 00C8_E 00C9_E 00CA_E 00CB_E 00CC_E 00CD_E 00CE_E 012D_E 012E_E 0137_E 0138_E 0139_E 0140_E 0141_E 0142_E 0143_E 0144_E 014A_E 014B_E 014C_E Sev. RAW)" "CCDM: Error writing raw file (CCDM.RAW)" "CCDM: The shutter could not be opened" "CCDM: The shutter could not be closed" "CCDM: Invalid CRC (check character) received with encrypted line" "CCDM: Wrong value for FRM_LOAD in Registry with CSCCCDM" "CCDM: Firmware loading could not be completed" "CCDM: Wrong value for LED. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "CCDM: Cheque/cash reader: the gap between two media is too small" "CCDM: Escrow tape at ELS2 defective" "CCDM: Escrow tape at ELS3 defective" "CCDM: Document into escrow not expected" "CCDM: Failure in ELS1 area" "CCDM: Document missing or escrow empty" "CCDM: Gap between two notes too long or jam at escrow unit" "CCDM: Initialisation not finished in the spezified time" "CCDM: Incorrect deflector position" "CCDM: Jam between sensor module (paper deflectors) and before RLS1" "CCDM: Document too short" "CCDM: Document too long" "CCDM: RLS1: jam or medium too long" "CCDM: RLS1: medium missing at KLS2 (module entry)" "CCDM: KLS2: unexpected medium at module entry" "CCDM: KLS2: jam or medium too long" "CCDM: Incorrect position of deflector in cassette module" "CCDM: KLS2: medium to retract box missing" "CCDM: Retract cassette: jam or medium too long" "CCDM: Incorrect position of deflector in cassette module 1" "CCDM: KLS2: medium to box 1 missing" "CCDM: Cassette module 1: jam or medium too long" "CCDM: Incorrect position of deflector in cassette module 2" "CCDM: KLS2: medium to box 2 missing" "CCDM: Cassette module 2: jam or medium too long" "CCDM: Media jam KLS5 . LED_FLASH or LED_FREQ" "CCDM: Wrong value for MAX_HEIGHT_CHEQUE. SCAN_FRONT_GREEN" "CCDM: Wrong value for SHUTTER_BEHAVIOUR in Registry with CSCCCDM" "CCDM: The thread which receives the image/signature data could not started" "CCDM: The thread which receives the image/signature data could not stopped" "CCDM: The pointer " "CCDM: The transferred cheque data (pointer.KSM" "CCDM: Error in cassette 1 during init" "CCDM: Error in cassette 2 during init" "CCDM: Invalid parameter in command" "CCDM: No document inserted" "CCDM: Function CscPrtRead was called. but no MICR mode via CscPrtControl selected" "CCDM: The CCDM device handler presumes MS-Windows 2000 or MS-Windows XP" "CCDM: There is still a document in the scanner" "CCDM: The CCDM-HW send unknown response to a command" "CCDM: Cannot open raw file (CCDM.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A Error Code 014D_E 0190_E 0191_E 0192_E 0193_E 0194_E 0195_E 0196_E 01F5_E 01F6_E 01F7_E 01F8_E 0259_E 025A_E 025B_E 025C_E 025D_E 025E_E 025F_E 0260_E 0261_E 0262_E 0263_E 0264_E 0265_E 0266_E 0267_E 0268_E 8000_E 8001_E 8002_E 8003_E 8004_E 8005_E 8006_E 8007_E 8008_E 8009_E 800A_E 800B_E 800C_E 800D_E 800E_E 800F_E 8010_E 8011_E 8012_E 8013_E 8014_E 8015_E 8016_E 8017_E 8018_E 8019_E 801A_E Sev. MAX_HEIGHT_NOTES. MAX_WIDTH_CHEQUE" "CCDM: Wrong value for the parameter SCAN_FRONT_RED. length) is illegal" "CCDM: No cheque number received while dispensing cheques or sheets" "CCDM: An error occurred while opening a currency file" "CCDM: An error occurred while opening a currency file" "CCDM: The currency file is not dedicated for the installed note sensor" "CCDM: A wrong keyword inside a currency file has been detected" "CCDM: The loading of new currency data not possible" 394 October 2004 U25604-J-Z745-1-7600 . banknotes not correct inserted)" "CCDM: Sheets not inserted in the given time period (reported by CscwCcdmEntry(.DLL returned undefined error" "CCDM: Tray operating error (e.g..DLL" "CCDM: Internal error while calling DQF.))" "CCDM: Some or all notes or checks not taken by the consumer" "CCDM: Some or all notes or checks not taken by the consumer while retract to IO or box" "CCDM: Sheets available in the IO tray.DLL" "CCDM: Internal error while calling DQF. e.DLL" "CCDM: Cannot open input file" "CCDM: Error reading input" "CCDM: Cannot open output file" "CCDM: Error writing output file" "CCDM: Not enough memory" "CCDM: Image too long" "CCDM: Image too large (for TIF)" "CCDM: Image too small (<1 row)" "CCDM: Error in final conversion step" "CCDM: Error in temp file access" "CCDM: Error loading imareco..DLL" "CCDM: Internal error while calling DQF.DLL" "CCDM: Internal error while calling DQF.g. rejected notes or cheques after dispensing" "CCDM: Loaded firmware older than the firmware found on disk" "CCDM: There is no firmware loaded in the CCCDM" "CCDM: Device handler was configured to switch LEDs when customer action is neccessary" "CCDM: Return of the function CscCcdmInit() if a new currency file has been detected" "CCDM: Returned by the function CscCcdmInit() if a new currency file has been detected" "CCDM: One or more new firmware loaded automatically by the Device Handler" "CCDM: Current loaded note table inconsistant to sensor Firmware" "CCDM: The firmware is not loaded in the CCDM" "CCDM: The parameters of the command have a wrong syntax" "CCDM: One of the locks is active or an error occurred that requires correction" "CCDM: An error occurred during the execution of the command" "CCDM: The safe door must be open for the execution of the actual command" "CCDM: The command cannot be executed at this point of time" U25604-J-Z745-1-7600 October 2004 395 .DLL" "CCDM: DQF.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A Error Code 801B_E 801C_E 801D_E 801E_E 801F_E 8020_E 8021_E 8022_E 8023_E 8024_E 8025_E 8026_E 8027_E 8030_E 9201_E 9202_E 9203_E 9204_E 9205_E 9206_E 9207_E 9208_E 9209_E 920A_E 920B_E 920C_E 92FF_E 9300_E 9301_E 9302_E 9303_E 9304_E 9305_E 93FF_E E000_W E001_W E002_W E003_W E004_W E00A_W E00B_W E00C_W E010_W E011_W E014_W E015_W F000_E F001_E F002_E F003_E F004_E F005_E Sev.DLL" "CCDM: Internal error while calling DQF.dll" "CCDM: IMACON. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "CCDM: New currency file loaded during installation" "CCDM: Error occurred while opening firmware file" "CCDM: Error occured while reading sensor firmware file" "CCDM: Firmware file is not dedicated for the installed sensor" "CCDM: Wrong value for SENS_FRM_LOAD in Registry with CSCCCDM" "CCDM: Not possible to read the current note table from the note sensor" "CCDM: Too much notes inserted" "CCDM: Timeout while waiting for signature ID" "CCDM: Number of detected cheques on ESCROW and number of scanned cheques different" "CCDM: Error in previous transaction" "CCDM: Error in previous transaction" "CCDM: Error occurred while opening a sensor firmware file" "CCDM: Error occured while reading a CCDM firmware file" "CCDM: The checksum of the signature data of a note is wrong" "CCDM: Illegal arguments calling IMACON.DLL returned undefined error" "CCDM: Internal error while calling DQF. CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A 001A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A Error Code F006_E F007_E F008_E F009_E F00A_E F00B_E F00C_E F00D_E F00E_E F00F_E F010_E F011_E F012_E F0A0_E F0A1_E F0A2_E F0A3_E F0A4_E F0A5_E F0A6_E F0A7_E F0A8_E DEFA_E DEFA_W FE09_E FE0A_E FE9C_E FE9E_E FEA0_E 0100_E 0210_E 0300_E 0305_E 8001_E 8010_E 0100_E 0200_E 0250_E 0270_E 0300_E 0350_E 0370_E 0400_E 0500_E 0572_E 0600_E Sev.DLL could not be opened" "IEEE1394/CCDM_CHQ: Internal driver error: Out of memory" "IEEE1394/CCDM_CHQ: Internal driver error: Device is not in working state" "IEEE1394/CCDM_CHQ: Internal driver error: Invalid parameter" "IEEE1394/CCDM_CHQ: Internal driver error: Size of buffer is invalid" "IEEE1394/CCDM_CHQ: Internal driver error: Device not found" "IEEE1394/CCDM_CHQ: Internal driver error: No such device instance" "IEEE1394/CCDM_CHQ: Internal driver error: The operation was cancelled/aborted" "IEEE1394/CCDM_CHQ: Internal driver error: A non-critical error occurred on the adapter" "IEEE1394/CCDM_CHQ: Internal driver error: The application has already opened the specified adapter" "IEEE1394/CCDM_CHQ: Internal driver error: The operation was cancelled because more bus resets" "IEEE1394/CCDM_CHQ: Internal driver error: The operation was cancelled because a 1394 bus reset" "IEEE1394/CCDM_CHQ: Internal driver error: The operation could not be completed because there was a conflict" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: A critical error occurred on the adapter that caused the request to fail" "IEEE1394/CCDM_CHQ: Internal driver error: The operation requested failed because the local adapter is busy" "IEEE1394/CCDM_CHQ: Internal driver error. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "CCDM: The application program tried to dispense a bundle. but the ESCROW is empty" "CCDM: ESCROW full while dispending a bundle" "CCDM: Cheques or sheets on ESCROW while performing the next transaction" "CCDM: Cheques or notes jammed on the ESCROW" "CCDM: There exists no hardware equipment to perform the requested command" "IEEE1394/CCDM_CHQ: Default error" "IEEE1394/CCDM_CHQ: Default warning" "IEEE1394/CCDM_CHQ: IEEE 1394 read command could not be executed in the specified monitoring time" "IEEE1394/CCDM_CHQ: A IEEE 1394 read command is cancelled by the user" "IEEE1394/CCDM_CHQ: The length in DataSize is 0 (zero)" "IEEE1394/CCDM_CHQ: The I1394_TS." "IEEE1394/CCDM_CHQ: Internal driver error: The driver detected a bug in its execution logic" 396 October 2004 U25604-J-Z745-1-7600 . but the IO-tray is empty" "CCDM: Customer did not remove the bundle until the command has timed out" "CCDM: Cheques or sheets are not correct inserted" "CCDM: CCDM firmware initiated a boot" "CCDM: Note sensor module reports hardware error" "CCDM: Note sensor module reports firmware error" "CCDM: Comunication error reported by the sensor module" "CCDM: Note sensor hase detected an error in the data format" "CCDM: Note sensor has detected an error in the note table" "CCDM: The assignment of a note is wrong" "CCDM: The sensor couldn't read the document (note or cheque)" "CCDM: An error occured during downloding of firmware or currency data" "CCDM: The sensor responded with an unknown error code" "CCDM: Bundle with detected metal in tray" "CCDM: Tray is occupied with not dispensable notes or cheques" "CCDM: A not specified tray error occurred" "CCDM: Shutter error while command CscCcdmCashIn" "CCDM: CscCcdmTransport command received.DLL could not be opened" "IEEE1394/CCDM_CHQ: The I1394_UB. device is powered down" "IEEE1394/CCDM_CHQ: Internal driver error: Invalid IO control code" "IEEE1394/CCDM_CHQ: Internal driver error: Requested byte count does not match buffer size" "IEEE1394/CCDM_CHQ: Internal driver error: Input buffer too small" "IEEE1394/CCDM_CHQ: Internal driver error: Output buffer too small" "IEEE1394/CCDM_CHQ: Internal driver error: Handle already used by an object of this type" "IEEE1394/CCDM_CHQ: Internal driver error: Handle already used by an object of another type" "IEEE1394/CCDM_CHQ: Internal driver error: Handle not associated with required object" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: Invalid configuration info type" U25604-J-Z745-1-7600 October 2004 397 .M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A Error Code 0639_E 0645_E 0658_E 0671_E 06B2_E 0700_E 0900_E 0A00_E 0C00_E 0D00_E 0D47_E 0F00_E 0F50_E 0F73_E 1070_E 1100_E 1200_E 1300_E 1313_E 132A_E 1350_E 1409_E 1433_E 1450_E 1500_E 0001_E 0010_E 0030_E 0110_E 0200_E 0220_E 0280_E 0302_E 0304_E 0310_E 0320_E 0340_E 0341_E 0342_E 0350_E 0351_E 0400_E Sev. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "IEEE1394/CCDM_CHQ: Internal driver error: The isochronous channel number is already in use" "IEEE1394/CCDM_CHQ: Internal driver error: An isochronous operation failed because of a FIFO" "IEEE1394/CCDM_CHQ: Internal driver error: An isochronous operation failed because of a FIFO underrun" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: An outgoing response packet is not valid" "IEEE1394/CCDM_CHQ: Internal driver error: An operation failed due to some lack of resources other" "IEEE1394/CCDM_CHQ: Internal driver error: The operation requested is not applicable to the channel" "IEEE1394/CCDM_CHQ: Internal driver error: The operation requested is not possible at the channel's current state" "IEEE1394/CCDM_CHQ: Internal driver error: Adapters not identified" "IEEE1394/CCDM_CHQ: Internal driver error: A validation check on a number of isochronous buffers failed" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: The request passed to the miniport was invalid" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: The requested item was not found" "IEEE1394/CCDM_CHQ: Internal driver error: The request valid. but adapter does not support the required functionality" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: The request cannot be transmitted" "IEEE1394/CCDM_CHQ: Internal driver error: The request cannot be transmitted" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error" "IEEE1394/CCDM_CHQ: Internal driver error: Operation failed" "IEEE1394/CCDM_CHQ: Internal driver error: Operation not supported" "IEEE1394/CCDM_CHQ: Internal driver error: Operation rejected" "IEEE1394/CCDM_CHQ: Internal driver error: Packet pool empty" "IEEE1394/CCDM_CHQ: Internal driver error: Device is removed" "IEEE1394/CCDM_CHQ: Internal driver error: Requested power state transition not allowed" "IEEE1394/CCDM_CHQ: Internal driver error: Operation rejected. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 01 01 01 01 01 01 01 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "IEEE1394/CCDM_CHQ: Internal driver error: Invalid local host info type" "IEEE1394/CCDM_CHQ: Internal driver error: Invalid local host property type" "IEEE1394/CCDM_CHQ: Internal driver error: Unsupported type of lock operation" "IEEE1394/CCDM_CHQ: Internal driver error: Unsupported speed selected" "IEEE1394/CCDM_CHQ: Internal driver error: Device not open" "IEEE1394/CCDM_CHQ: Internal driver error: Request timeout interval has expired" "IEEE1394/CCDM_CHQ: Internal driver error: Invalid parameter in function call" "IEEE1394/CCDM_CHQ: Internal driver error: Memory allocation failed" "IEEE1394/CCDM_CIN: Default error" "IEEE1394/CCDM_CIN: Default warning" "IEEE1394/CCDM_CIN: IEEE 1394 read command could not be executed in the specified monitoring time" "IEEE1394/CCDM_CIN: A IEEE 1394 read command is cancelled by the user" "IEEE1394/CCDM_CIN: The length in DataSize is 0 (zero)" "IEEE1394/CCDM_CIN: The I1394_TS.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class AA1A AA1A AA1A AA1A AA1A AA1A AA1A AA1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A Error Code 0401_E 0402_E 0403_E 0404_E 8002_E 8003_E 8008_E 8020_E DEFA_E DEFA_W FE09_E FE0A_E FE9C_E FE9E_E FEA0_E 0100_E 0210_E 0300_E 0305_E 8001_E 8010_E 0100_E 0200_E 0250_E 0270_E 0300_E 0350_E 0370_E 0400_E 0500_E 0572_E 0600_E 0639_E 0645_E 0658_E 0671_E 06B2_E 0700_E 0900_E 0A00_E Sev.DLL could not be opened" "IEEE1394/CCDM_CIN: Internal driver error: Out of memory" "IEEE1394/CCDM_CIN: Internal driver error: Device is not in working state" "IEEE1394/CCDM_CIN: Internal driver error: Invalid parameter" "IEEE1394/CCDM_CIN: Internal driver error: Size of buffer is invalid" "IEEE1394/CCDM_CIN: Internal driver error: Device not found" "IEEE1394/CCDM_CIN: Internal driver error: No such device instance" "IEEE1394/CCDM_CIN: Internal driver error: The operation was cancelled/aborted" "IEEE1394/CCDM_CIN: Internal driver error: A non-critical error occurred on the adapter" "IEEE1394/CCDM_CIN: Internal driver error: The application has already opened the specified adapter" "IEEE1394/CCDM_CIN: Internal driver error: The operation was cancelled because more bus resets" "IEEE1394/CCDM_CIN: Internal driver error: The operation was cancelled because a 1394 bus reset" "IEEE1394/CCDM_CIN: Internal driver error: The operation could not be completed because there was a conflict" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: A critical error occurred on the adapter that caused the request to fail" "IEEE1394/CCDM_CIN: Internal driver error: The operation requested failed because the local adapter is busy" "IEEE1394/CCDM_CIN: Internal driver error." "IEEE1394/CCDM_CIN: Internal driver error: The driver detected a bug in its execution logic" "IEEE1394/CCDM_CIN: Internal driver error: The isochronous channel number is already in use" "IEEE1394/CCDM_CIN: Internal driver error: An isochronous operation failed because of a FIFO" "IEEE1394/CCDM_CIN: Internal driver error: An isochronous operation failed because of a FIFO underrun" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: An outgoing response packet is not valid" "IEEE1394/CCDM_CIN: Internal driver error: An operation failed due to some lack of resources other" "IEEE1394/CCDM_CIN: Internal driver error: The operation requested is not applicable to the channel" "IEEE1394/CCDM_CIN: Internal driver error: The operation requested is not possible at the channel's current state" 398 October 2004 U25604-J-Z745-1-7600 .DLL could not be opened" "IEEE1394/CCDM_CIN: The I1394_UB. device is powered down" "IEEE1394/CCDM_CIN: Internal driver error: Invalid IO control code" "IEEE1394/CCDM_CIN: Internal driver error: Requested byte count does not match buffer size" "IEEE1394/CCDM_CIN: Internal driver error: Input buffer too small" "IEEE1394/CCDM_CIN: Internal driver error: Output buffer too small" "IEEE1394/CCDM_CIN: Internal driver error: Handle already used by an object of this type" "IEEE1394/CCDM_CIN: Internal driver error: Handle already used by an object of another type" "IEEE1394/CCDM_CIN: Internal driver error: Handle not associated with required object" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: Invalid configuration info type" "IEEE1394/CCDM_CIN: Internal driver error: Invalid local host info type" "IEEE1394/CCDM_CIN: Internal driver error: Invalid local host property type" "IEEE1394/CCDM_CIN: Internal driver error: Unsupported type of lock operation" "IEEE1394/CCDM_CIN: Internal driver error: Unsupported speed selected" "IEEE1394/CCDM_CIN: Internal driver error: Device not open" "IEEE1394/CCDM_CIN: Internal driver error: Request timeout interval has expired" "IEEE1394/CCDM_CIN: Internal driver error: Invalid parameter in function call" "IEEE1394/CCDM_CIN: Internal driver error: Memory allocation failed" "USB/CCDM_CIN: DEFAULT_WARNING" "USB/CCDM_CIN: DEFAULT_ERROR" U25604-J-Z745-1-7600 October 2004 399 . but adapter does not support the required functionality" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: The request cannot be transmitted" "IEEE1394/CCDM_CIN: Internal driver error: The request cannot be transmitted" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: Operation failed" "IEEE1394/CCDM_CIN: Internal driver error: Operation not supported" "IEEE1394/CCDM_CIN: Internal driver error: Operation rejected" "IEEE1394/CCDM_CIN: Internal driver error: Packet pool empty" "IEEE1394/CCDM_CIN: Internal driver error: Device is removed" "IEEE1394/CCDM_CIN: Internal driver error: Requested power state transition not allowed" "IEEE1394/CCDM_CIN: Internal driver error: Operation rejected. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "IEEE1394/CCDM_CIN: Internal driver error: Adapters not identified" "IEEE1394/CCDM_CIN: Internal driver error: A validation check on a number of isochronous buffers failed" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: The request passed to the miniport was invalid" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error" "IEEE1394/CCDM_CIN: Internal driver error: The requested item was not found" "IEEE1394/CCDM_CIN: Internal driver error: The request valid.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A BB1A CC1A CC1A Error Code 0C00_E 0D00_E 0D47_E 0F00_E 0F50_E 0F73_E 1070_E 1100_E 1200_E 1300_E 1313_E 132A_E 1350_E 1409_E 1433_E 1450_E 1500_E 0001_E 0010_E 0030_E 0110_E 0200_E 0220_E 0280_E 0302_E 0304_E 0310_E 0320_E 0340_E 0341_E 0342_E 0350_E 0351_E 0400_E 0401_E 0402_E 0403_E 0404_E 8002_E 8003_E 8008_E 8020_E DEFA_W DEFA_E Sev. error is reported by the USB host" "USB/CCDM_CIN: Data overrun error detected.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A Error Code 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E Sev. error is reported by the USB host controller" "USB/CCDM_CIN: Unexpected PID detected. error is reported by the USB bus driver USBD" "USB/CCDM_CIN: Invalid pipe handle has been passed. error is reported by the USB bus" "USB/CCDM_CIN: Bad start frame has been specified. error is reported by the USB host controller" "USB/CCDM_CIN: USB device is not responding. error is reported by the USB host" "USB/CCDM_CIN: PID check has failed. error is reported by the USB host" "USB/CCDM_CIN: Error code is reserved by the USB host controller driver" "USB/CCDM_CIN: Error code is reserved by the USB host controller driver" "USB/CCDM_CIN: Buffer overrun has been detected. data transfer phase exceeds the USB frame length" "USB/CCDM_CIN: Data buffer error has been detected. PCI bus latency was too long" "USB/CCDM_CIN: XACT error has been detected. error is reported by the USB bus" "USB/CCDM_CIN: Invalid URB function code has been passed. error is reported by the USB host" "USB/CCDM_CIN: Endpoint has been halted by the USB bus driver USBD" "USB/CCDM_CIN: Memory allocation attempt has failed. error is reported by the USB bus driver" 400 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB host" "USB/CCDM_CIN: Buffer was not accessed. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "USB/CCDM_CIN: Unexpected descriptor was reported from USB device" "USB/CCDM_CIN: Device not found" "USB/CCDM_CIN: Not enough memory available" "USB/CCDM_CIN: It was no endpoint found in the descriptor" "USB/CCDM_CIN: The creation of the list of USB devices failed" "USB/CCDM_CIN: USB read command could not be executed in the specified monitoring time" "USB/CCDM_CIN: USB READ command is cancelled by the user" "USB/CCDM_CIN: The pointer pData is illegal" "USB/CCDM_CIN: The length in DataSize is 0 (zero)" "USB/CCDM_CIN: CRC error has been detected" "USB/CCDM_CIN: Bit stuffing error has been detected" "USB/CCDM_CIN: DATA toggle mismatch has been detected" "USB/CCDM_CIN: STALLPID has been detected. error is reported by the USB bus" "USB/CCDM_CIN: Asynchronous request has failed. error is reported by the USB host" "USB/CCDM_CIN: Device is babbling. error is reported by the USB host" "USB/CCDM_CIN: Buffer underrun has been detected. error is reported by the USB bus" "USB/CCDM_CIN: There are data transfer requests pending for the device" "USB/CCDM_CIN: Request has failed. error is reported by the USB host" "USB/CCDM_CIN: FIFO error has been detected. error is reported by the USB host" "USB/CCDM_CIN: Data underrun error detected. error is reported by the USB" "USB/CCDM_CIN: Invalid parameter has been passed. error is reported by the USB bus" "USB/CCDM_CIN: There is not enough bandwidth available. error is reported by the USB bus" "USB/CCDM_CIN: Internal host controller error has been detected" "USB/CCDM_CIN: Short transfer has been detected. M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A Error Code 0C00_E 0D00_E 0E00_E 0F00_E 1000_E 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E Sev. This error is reported by the USBIO driver" "USB/CCDM_CIN: The specified pipe was not found in the current configuration" "USB/CCDM_CIN: An invalid asynchronous data packet has been specified" "USB/CCDM_CIN: There are not enough system resources to complete the operation" "USB/CCDM_CIN: Specified interface was not found in the current configuration" "USB/CCDM_CIN: Operation cannot be executed while the USB device is in the current state" "USB/CCDM_CIN: Invalid parameter has been specified with an IOCTL operation" "USB/CCDM_CIN: Evaluation interval of the USBIO DEMO version has expired" "USB/CCDM_CIN: Invalid power state has been specified" "USB/CCDM_CIN: Device has entered a power down state" "USB/CCDM_CIN: API version reported by the USBIO driver does not match" "USB/CCDM_CIN: Set configuration operation has failed. error is reported by the USBIO driver" "USB/CCDM_CIN: Either the handle is already bound to a pipe" "USB/CCDM_CIN: Handle is not bound to a pipe. error is reported by the USBIO" "USB/CCDM_CIN: USB device is already configured. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "USB/CCDM_CIN: USB frame control is currently owned. error is reported by the USB bus" "USB/CCDM_CIN: USB frame control is currently not owned. error is reported by the USB" "USB/CCDM_CIN: Operation is not supported. error is reported by the USBIO" "USB/CCDM_CIN: Direction of the data transfer request is not supported by that pipe" "USB/CCDM_CIN: Number of asynchronous data packets specified in an asynchronous read" "USB/CCDM_CIN: Memory resources are exhausted. error is reported by the USBIO driver" "USB/CCDM_CIN: There are open pipes. error is reported by the USB bus driver" "USB/CCDM_CIN: Invalid configuration descriptor was reported by the device" "USB/CCDM_CIN: Operation has failed. error is reported by the USBIO driver" "USB/CCDM_CIN: USB device has been removed from the system" "USB/CCDM_CIN: Specified control code is not supported" "USB/CCDM_CIN: Operation has been timed out. error is reported by the USBIO" "USB/CCDM_CIN: The USB device is not configured. error is reported by the USBIO driver" "USB/CCDM_CIN: Invalid input buffer has been passed to an IOCTL operation" "USB/CCDM_CIN: Invalid output buffer has been passed to an IOCTL operation" "USB/CCDM_CIN: There is not enough system memory available to complete the operation" "USB/CCDM_CIN: There are read or write requests pending. error is reported by the USBIO driver" "USB/CCDM_CIN: Invalid recipient has been specified" "USB/CCDM_CIN: Either an invalid request type has been specified" "USB/CCDM_CIN: Invalid IOCTL code has been specified. error is reported by the USBIO" "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" U25604-J-Z745-1-7600 October 2004 401 . error is reported by the USB host controller" "USB/CCDM_CHQ: USB device is not responding. error is reported by the USB host" "USB/CCDM_CHQ: Error code is reserved by the USB host controller driver" "USB/CCDM_CHQ: Error code is reserved by the USB host controller driver" "USB/CCDM_CHQ: Buffer overrun has been detected. error is reported by the USB host" "USB/CCDM_CHQ: PID check has failed. error is reported by the USB host" "USB/CCDM_CHQ: Buffer was not accessed.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A CC1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A Error Code 1083_E 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E Sev. error is reported by the USB bus driver" "USB/CCDM_CIN: USB device is gone. there is no valid handle to execute the operation" "USB/CCDM_CIN: Enumeration of the specified devices has failed" "USB/CCDM_CIN: Invalid parameter has been passed to a function" "USB/CCDM_CIN: Library setupapi. error is reported by the USB host" "USB/CCDM_CHQ: Data underrun error detected. PCI bus latency was too long" 402 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB host controller" "USB/CCDM_CHQ: Unexpected PID detected. error is reported by the USB bus driver USBD" "USB/CCDM_CIN: Interface was not found. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CIN: The specified device object does not exist" "USB/CCDM_CIN: Device object was opened. error is reported by the USB bus driver USBD" "USB/CCDM_CHQ: DEFAULT_WARNING" "USB/CCDM_CHQ: DEFAULT_ERROR" "USB/CCDM_CHQ: Unexpected descriptor was reported from USB device" "USB/CCDM_CHQ: Device not found" "USB/CCDM_CHQ: Not enough memory available" "USB/CCDM_CHQ: It was no endpoint found in the descriptor" "USB/CCDM_CHQ: The creation of the list of USB devices failed" "USB/CCDM_CHQ: USB read command could not be executed in the specified monitoring time" "USB/CCDM_CHQ: USB READ command is cancelled by the user" "USB/CCDM_CHQ: The pointer pData is illegal" "USB/CCDM_CHQ: The length in DataSize is 0 (zero)" "USB/CCDM_CHQ: CRC error has been detected" "USB/CCDM_CHQ: Bit stuffing error has been detected" "USB/CCDM_CHQ: DATA toggle mismatch has been detected" "USB/CCDM_CHQ: STALLPID has been detected.dll could not be loaded" "USB/CCDM_CIN: Set configuration request has failed" "USB/CCDM_CIN: Buffer is too small. error is reported by the USB host" "USB/CCDM_CHQ: Buffer underrun has been detected. error is reported by the USB bus driver USBD" "USB/CCDM_CIN: Invalid pipe flags have been specified" "USB/CCDM_CIN: Operation has been timed out. error is reported by the USB host" "USB/CCDM_CHQ: Data overrun error detected. error is reported by the USB host" "USB/CCDM_CHQ: FIFO error has been detected. M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A Error Code 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E Sev. error is reported by the USB" "USB/CCDM_CHQ: Invalid parameter has been passed. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/CCDM_CHQ: XACT error has been detected. error is reported by the USBIO driver" "USB/CCDM_CHQ: There are open pipes. error is reported by the USBIO" "USB/CCDM_CHQ: The USB device is not configured. error is reported by the USB bus" "USB/CCDM_CHQ: There is not enough bandwidth available. error is reported by the USB bus" "USB/CCDM_CHQ: Invalid URB function code has been passed. data transfer phase exceeds the USB frame length" "USB/CCDM_CHQ: Data buffer error has been detected. error is reported by the USB bus driver USBD" "USB/CCDM_CHQ: Invalid pipe handle has been passed. error is reported by the USB host" "USB/CCDM_CHQ: Endpoint has been halted by the USB bus driver USBD" "USB/CCDM_CHQ: Memory allocation attempt has failed. error is reported by the USB bus" "USB/CCDM_CHQ: Bad start frame has been specified. error is reported by the USBIO driver" "USB/CCDM_CHQ: Invalid recipient has been specified" "USB/CCDM_CHQ: Either an invalid request type has been specified" "USB/CCDM_CHQ: Invalid IOCTL code has been specified. error is reported by the USB bus" "USB/CCDM_CHQ: Asynchronous request has failed. error is reported by the USB" "USB/CCDM_CHQ: Operation is not supported. error is reported by the USBIO driver" "USB/CCDM_CHQ: Either the handle is already bound to a pipe" "USB/CCDM_CHQ: Handle is not bound to a pipe. error is reported by the USBIO driver" "USB/CCDM_CHQ: Invalid input buffer has been passed to an IOCTL operation" "USB/CCDM_CHQ: Invalid output buffer has been passed to an IOCTL operation" "USB/CCDM_CHQ: There is not enough system memory available to complete the operation" "USB/CCDM_CHQ: There are read or write requests pending. error is reported by the USB bus" "USB/CCDM_CHQ: Internal host controller error has been detected" "USB/CCDM_CHQ: Short transfer has been detected. error is reported by the USBIO" "USB/CCDM_CHQ: USB device is already configured. error is reported by the USB bus" "USB/CCDM_CHQ: USB frame control is currently not owned. error is reported by the USB bus" "USB/CCDM_CHQ: There are data transfer requests pending for the device" "USB/CCDM_CHQ: Request has failed. error is reported by the USBIO" "USB/CCDM_CHQ: Direction of the data transfer request is not supported by that pipe" "USB/CCDM_CHQ: Number of asynchronous data packets specified in an asynchronous read" U25604-J-Z745-1-7600 October 2004 403 . error is reported by the USB bus driver" "USB/CCDM_CHQ: Invalid configuration descriptor was reported by the device" "USB/CCDM_CHQ: Operation has failed. error is reported by the USB host" "USB/CCDM_CHQ: Device is babbling. error is reported by the USB bus driver" "USB/CCDM_CHQ: USB frame control is currently owned. error is reported by the USBIO driver" "USB/CCDM_CHQ: USB device has been removed from the system" "USB/CCDM_CHQ: Specified control code is not supported" "USB/CCDM_CHQ: Operation has been timed out. dll could not be loaded" "USB/CCDM_CHQ: Set configuration request has failed" "USB/CCDM_CHQ: Buffer is too small. there is no valid handle to execute the operation" "USB/CCDM_CHQ: Enumeration of the specified devices has failed" "USB/CCDM_CHQ: Invalid parameter has been passed to a function" "USB/CCDM_CHQ: Library setupapi. error is reported by the USB bus driver USBD" "USB/CCDM_CHQ: Interface was not found. This error is reported by the USBIO driver" "USB/CCDM_CHQ: The specified pipe was not found in the current configuration" "USB/CCDM_CHQ: An invalid asynchronous data packet has been specified" "USB/CCDM_CHQ: There are not enough system resources to complete the operation" "USB/CCDM_CHQ: Specified interface was not found in the current configuration" "USB/CCDM_CHQ: Operation cannot be executed while the USB device is in the current state" "USB/CCDM_CHQ: Invalid parameter has been specified with an IOCTL operation" "USB/CCDM_CHQ: Evaluation interval of the USBIO DEMO version has expired" "USB/CCDM_CHQ: Invalid power state has been specified" "USB/CCDM_CHQ: Device has entered a power down state" "USB/CCDM_CHQ: API version reported by the USBIO driver does not match" "USB/CCDM_CHQ: Set configuration operation has failed.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A DD1A Error Code 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E 1083_E 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E Sev. error is reported by the USB bus driver USBD" 404 October 2004 U25604-J-Z745-1-7600 . 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/CCDM_CHQ: Memory resources are exhausted. error is reported by the USB bus driver" "USB/CCDM_CHQ: USB device is gone. error is reported by the USBIO" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/CCDM_CHQ: The specified device object does not exist" "USB/CCDM_CHQ: Device object was opened. error is reported by the USB bus driver USBD" "USB/CCDM_CHQ: Invalid pipe flags have been specified" "USB/CCDM_CHQ: Operation has been timed out. command cannot be executed" "EDM: No or not enough PIN numbers entered" "EDM: Key-splitting E-PROM not connected or wrong" "EDM: Checksum of key-splitting E-PROM is wrong" "EDM: Parity error in key of the key-splitting E-PROM" "EDM: Invalid table charater in key-splitting E-PROM" "EDM: V24 connection PC to EDM was/is interrupted" "EDM: Battery problem of EDM" "EDM: EPP detects an error when entering a key" "EDM: EDM not initialized" "EDM: Length in the parameter cannot be divided by eight" "EDM: The DLL command specification is invalid" "EDM: The command parameters are incorrect" "EDM: Invalid key number" "EDM: Error during data transmission" "EDM: Initialize vector has wrong length" "EDM: No free space in IV array" "EDM: System could not provide dynamic memory" "EDM: Wrong maximum PIN length with job EdmStartPin" "EDM: Wrong minimum PIN length with job EdmStartPin" "EDM: Invalid field for leading zeros in the PIN structure" "EDM: Invalid field for acknowledge key in the PIN structure" "EDM: Invalid mode in the PIN structure" "EDM: Wrong PIN position in PIN field" "EDM: Wrong structure entry in field TestMode" "EDM: Invalid number of PIN digits" "EDM: This API is not supported by the device handler" "EDM: The API could not be loaded" "EDM: This function cannot be accessed with the firmware" "EDM: Cannot access full length of data area in a structure" "EDM: Invalid encryption mode specified for key reset" "EDM: The total protocol monitoring time has been exceeded" U25604-J-Z745-1-7600 October 2004 405 .M-Status & M-Data Reference Tables CSC-W32 Error Classes Encryption Decryption Module (Class: 000F) The following table lists the M-Status and M-Data codes assigned to the device class Encryption Decryption Module (EDM). Table 102: Encryption Decryption Module (EDM) (Class: 000F) Error Error Class Code 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E 8005_E 8006_E 8007_E 8008_E 8009_E 800A_E 800B_E 800C_E 800D_E 800E_E 800F_E 8010_E 8011_E 8040_E 8041_E 8050_E 8051_E 8052_E 8053_E 8060_E 8061_E 8062_E 8101_E 8102_E 8103_E 8104_E 8105_E 8107_E 810B_E 810C_E 810E_E 8111_E 8112_E 8113_E 8114_E 8115_E 8116_E 8118_E 8119_E 811A_E 811B_E 811C_E 811E_E 811F_E 8120_E Sev. 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 98 98 11 98 01 02 02 02 02 56 02 12 00 56 12 12 12 12 00 11 02 02 01 02 07 02 00 13 56 00 11 38 07 56 16 02 56 70 70 70 70 70 70 70 02 02 07 07 07 07 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "EDM: DEFAULT_WARNING" "EDM: DEFAULT_ERROR" "EDM: An undefined internal error has occurred in the firmware" "EDM: The firmware cannot execute the command" "EDM: Key address not allowed" "EDM: EDM RAM error" "EDM: Parity error in key" "EDM: Internal hardware E-PROM error" "EDM: Internal hardware EE-PROM error" "EDM: The EDM command does not exist" "EDM: The EDM key RAM is defective" "EDM: The transferred data length is invalid" "EDM: An invalid block ID is in the V24 protocal" "EDM: The device ID is invalid" "EDM: Command already transferred to the EDM firmware" "EDM: Command length and data length invalid" "EDM: Output parameters not defined" "EDM: Data contains invalid ASCII characters" "EDM: Wrong sequence of commands" "EDM: Wrong ID" "EDM: No transaction active. CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 000F 000F 000F 000F 000F 000F 000F 8121_E 8122_E 8123_E 8124_E 8125_E 8126_E 8127_E Sev. block cannot divided by eight" "EDS: Error while accessing the CSCEDSKEY key file" 406 October 2004 U25604-J-Z745-1-7600 . Table 103: Encryption Decryption Software (EDS) (Class: 0011) Error Error Class Code 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 DEFA_W DEFA_E 8001_E 8002_E 8003_E 8004_E 8005_E 8007_E 8008_E 800A_E 800B_E 800C_E Sev. 2 2 2 2 2 2 2 MStatus 00 00 07 12 12 13 75 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "EDM: The maximum number of receive repeats has been reached" "EDM: The received acknowledge type is invalid" "EDM: Common protocol error in EPP response data" "EDM: Key Generating Keys in REGISTRY/CSCINI are not correct" "EDM: Invalid character in KGK Keyset in REGISTRY/CSCINI" "EDM: Error when encrypting a Masterkey" "EDM: The check is negativ" Encryption Decryption Software (Class: 0011) The following table lists the M-Status and M-Data codes assigned to the device class Encryption Decryption Software (EDS). 2 4 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 13 22 13 01 13 13 01 11 56 13 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "EDS: DEFAULT_WARNING" "EDS: DEFAULT_ERROR" "EDS: No transport key is loaded" "EDS: An invalid transport key is available" "EDS: No CBC key is loaded" "EDS: An invalid CBC key is available" "EDS: No initial vector loaded" "EDS: No ECB key is loaded" "EDS: An invalid ECB key is available" "EDS: The length specified in the parameter block is zero" "EDS: Length specified in param. Class AA08 is the USB class assigned to the Card Reader. device is in maintanance mode " "CARD READER: Internal encountered in firmware of IDCU device" "CARD READER: Card jammed (possible manipulation)" "CARD READER: The sensors report an invalid position of the shutter" "CARD READER: Sensors are defect" "CARD READER: Card too long" "CARD READER: Card too short" "CARD READER: Memory error" "CARD READER: Card has shifted" "CARD READER: The card is jammed" "CARD READER: Shutter switch or width switch defective" "CARD READER: Mechanical error of IDCU device" "CARD READER: The data read from the cards have the wrong parity" "CARD READER: The card data could not be read" "CARD READER: The WRITE data is faulty on the card" "CARD READER: The end character only was found on the track when read" "CARD READER: Power fail during a command" "CARD READER: The DSR signal is in OFF status" "CARD READER: The card was removed during transport from the output position to the reject box" "CARD READER: There is presently no firmware loaded in the device" "CARD READER: There was a problem during the download of the firmware" "CARD READER: The card data could not be read" "CARD READER: Card jammed in optional stacker unit (possible manipulation)" "CARD READER: No card in the dispenser" "CARD READER: Card is clamped by the ID card unit" "CARD READER: The chip card controller in the IDU or the IC card is defect" "CARD READER: The chip card could not be activated" "CARD READER: The chip card could not be deactivated" "CARD READER: An error occurred during communication with the chip card" "CARD READER: A forced interruption command was received from the chip card" "CARD READER: Error detected in response from the chip card" "CARD READER: The ATR information of the card is incorrect" "CARD READER: Chip card mode or SAM configuration not supported" "CARD READER: Flash memory needs to be reset" "CARD READER: Trigger level of transactions has been reached" "CARD READER: Error occurred during access of SEL DH to switch LED's" "CARD READER: Temporary power failure between last job and current job" "CARD READER: Maximum number of tries per command is reached" "CARD READER: Not enough data received from IDCU" "CARD READER: Error in communication protocal with IDCU" U25604-J-Z745-1-7600 October 2004 407 . Table 104: Card Reader (Class: 0008/AA08) Error Class 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 Error Code DEFA_E DEFA_W 0000_W 0000_E 1004_E 1005_E 100F_E 1015_E E000_E E001_E E002_E E004_E E006_E E009_E E00A_E E00B_E E00C_E E00D_E E00E_E E00F_E E010_E E011_E E012_E E013_E E014_E E015_E E016_E E017_E E01E_E E01F_E E028_E E070_E E071_E E100_E E101_E E102_E E104_E E180_E E182_E E183_E E184_E E185_E E186_E E187_E 7FFB_E 7FFC_E 7FFD_E 7FFE_E 7FFF_E F001_E F002_E F003_E Sev.M-Status & M-Data Reference Tables CSC-W32 Error Classes Card Reader (Class: 0008/AA08) The following table lists the M-Status and M-Data codes assigned to the device class Card Reader. 2 2 0 2 2 2 4 4 2 2 2 2 4 4 2 3 2 3 3 4 3 3 2 2 0 2 2 2 4 4 2 4 4 2 3 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 03 03 03 03 00 00 13 00 20 20 18 07 08 13 13 20 13 13 08 11 03 03 04 03 20 20 12 20 20 03 18 18 18 03 03 03 03 03 03 03 03 03 03 03 03 03 20 20 MData 0000000000 0000000000 0000000000 0000000000 0205000000 0205000000 0205000000 0205000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0205000000 0000000000 0000000000 Status desription INFO "CARD READER: DEFAULT_ERROR" "CARD READER: DEFAULT_WARNING" "CARD READER: If no warning found" "CARD READER: If no error found" "CARD READER: Length of input buffer in parameter block invalid" "CARD READER: Length of output buffer in parameter block invalid" "CARD READER: Device handler not initialized (card trap ?)" "CARD READER: Executed command not permitted or possible" "CARD READER: Invalid command (internal error)" "CARD READER: Parameters not correct" "CARD READER: Command cannot be executed" "CARD READER: Invalid data with a command" "CARD READER: Command cannot be executed. DLL could not be loaded" "CARD READER: V24 Communication timeout" "CARD READER: V24 Communication timeout" "CARD READER: Initialization failed" "USB/IDCU: DEFAULT_WARNING" "USB/IDCU: DEFAULT_ERROR" "USB/IDCU: Unexpected descriptor was reported from USB device" "USB/IDCU: Device not found" "USB/IDCU: Not enough memory available" "USB/IDCU: It was no endpoint found in the descriptor" "USB/IDCU: The creation of the list of USB devices failed" "USB/IDCU: USB read command could not be executed in the specified monitoring time" "USB/IDCU: USB READ command is cancelled by the user" "USB/IDCU: The pointer pData is illegal" "USB/IDCU: The length in DataSize is 0 (zero)" "USB/IDCU: CRC error has been detected" "USB/IDCU: Bit stuffing error has been detected" "USB/IDCU: DATA toggle mismatch has been detected" "USB/IDCU: STALLPID has been detected. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 2 2 2 4 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 20 20 20 20 20 20 20 20 20 20 20 04 20 00 00 05 00 20 00 00 00 20 00 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 FE08000000 FE09000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 Status desription INFO "CARD READER: V24 line error No ENQ was sent" "CARD READER: Response from IDCU is incorrect" "CARD READER: Invalid status" "CARD READER: Invalid parameters with the command" "CARD READER: Internal RESET not possible (internal error)" "CARD READER: TYPE in Registry/CSCINI with CSCIDU is incorrect" "CARD READER: False value for ID_PM in Registry/CSCINI with CSCIDU" "CARD READER: Wrong value for ID_PD in Registry/CSCINI with CSCIDU" "CARD READER: False value for ID_WV in Registry/CSCINI with CSCIDU" "CARD READER: False value for ID_SH in Registry/CSCINI with CSCIDU" "CARD READER: Command is not available in this configuration" "CARD READER: V24 send command not terminated with correct length" "CARD READER: NAK received as a response" "CARD READER: CANCEL not possible" "CARD READER: A CsclduCancel command has already been sent" "CARD READER: No card in the unit to perform the command" "CARD READER: Wrong value for MSS in Registry/CSCINI with CSCIDU" "CARD READER: The device handler MSS could not be loaded" "CARD READER: Wrong value for ID_WT in Registry/CSCINI with CSCIDU" "CARD READER: Wrong value for ID_RJ in Registry/CSCINI with CSCIDU" "CARD READER: Wrong value for MAN_RECOG in Registry/CSCINI with CSCIDU" "CARD READER: The device handler CSCWHYBDLL could not be loaded" "CARD READER: Wrong value for LED in Registry/CSCINI with CSCIDU" "CARD READER: The device handler CSCWSELDLL could not be loaded" "CARD READER: The device handler CSCWCITDLL could not be loaded" "CARD READER: The specified firmware file has not the correct format" "CARD READER: The parameter INIT_LOADER_CTL in the Registry/CSCINI is incorrect" "CARD READER: DH CSCWTRADLL and /or CSCWESTDLL could not be loaded" "CARD READER: TRANSACTION-ACTIVE in the Registry/CSCINI is incorrect" "CARD READER: TRANSACTION-TRIGGER in the Registry/CSCINI is incorrect" "CARD READER: ERROR-MAPPING in the Registry/CSCINI is incorrect" "CARD READER: Parameter CHIPMODE in registry is incorrect" "CARD READER: Wrong value for ENTRY_HANDLING" "CARD READER: Device handler CSCSWI.DLL could not be loaded" "CARD READER: Parameter SAMx_MODE incorrect" "CARD READER: Parameter SAM incorrect" "CARD READER: Device handler CSCWV2X.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 0008 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 Error Code F004_E F005_E F006_E F007_E F008_E F009_E F00B_E F00C_E F00D_E F00E_E F00F_E F011_E F012_E F013_E F014_E F015_E F016_E F017_E F018_E F019_E F01A_E F01B_E F01C_E F01D_E F01E_E F020_E F021_E F022_E F023_E F024_E F025_E F026_E F027_E F028_E F029_E F02A_E F02B_E F02C_E F02D_E F02E_E F02F_E FE08_E FE09_E FE7B_E DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E Sev.DLL could not be loaded" "CARD READER: Device handler CSCWHUS. error is reported by the USB host controller" 408 October 2004 U25604-J-Z745-1-7600 .DLL could not be loaded" "CARD READER: Device handler CSCWICM.DLL could not be loaded" "CARD READER: Device handler CSCEDS.DLL could not be loaded" "CARD READER: Device handler CSCEDM. error is reported by the USB host" "USB/IDCU: PID check has failed. error is reported by the USB host controller" "USB/IDCU: USB device is not responding. error is reported by the USB bus" "USB/IDCU: Bad start frame has been specified. error is reported by the USB bus" "USB/IDCU: There is not enough bandwidth available. error is reported by the USBIO driver" "USB/IDCU: USB device has been removed from the system" "USB/IDCU: Specified control code is not supported" "USB/IDCU: Operation has been timed out. error is reported by the USB bus" "USB/IDCU: USB frame control is currently not owned. PCI bus latency was too long" "USB/IDCU: XACT error has been detected. error is reported by the USBIO driver" "USB/IDCU: Invalid recipient has been specified" "USB/IDCU: Either an invalid request type has been specified" "USB/IDCU: Invalid IOCTL code has been specified. error is reported by the USB host" "USB/IDCU: Endpoint has been halted by the USB bus driver USBD" "USB/IDCU: Memory allocation attempt has failed. error is reported by the USBIO" "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" U25604-J-Z745-1-7600 October 2004 409 . error is reported by the USB" "USB/IDCU: Invalid parameter has been passed. error is reported by the USB host" "USB/IDCU: Data overrun error detected. error is reported by the USBIO" "USB/IDCU: The USB device is not configured. error is reported by the USB host" "USB/IDCU: Buffer underrun has been detected. error is reported by the USBIO driver" "USB/IDCU: There are open pipes. error is reported by the USB" "USB/IDCU: Operation is not supported. error is reported by the USB bus" "USB/IDCU: There are data transfer requests pending for the device" "USB/IDCU: Request has failed. error is reported by the USB host" "USB/IDCU: Buffer was not accessed. error is reported by the USB bus driver" "USB/IDCU: Invalid configuration descriptor was reported by the device" "USB/IDCU: Operation has failed. error is reported by the USB bus driver USBD" "USB/IDCU: Invalid pipe handle has been passed. error is reported by the USBIO driver" "USB/IDCU: Either the handle is already bound to a pipe" "USB/IDCU: Handle is not bound to a pipe. error is reported by the USB host" "USB/IDCU: Error code is reserved by the USB host controller driver" "USB/IDCU: Error code is reserved by the USB host controller driver" "USB/IDCU: Buffer overrun has been detected. error is reported by the USB bus driver" "USB/IDCU: USB frame control is currently owned. error is reported by the USB host" "USB/IDCU: FIFO error has been detected. error is reported by the USBIO driver" "USB/IDCU: Invalid input buffer has been passed to an IOCTL operation" "USB/IDCU: Invalid output buffer has been passed to an IOCTL operation" "USB/IDCU: There is not enough system memory available to complete the operation" "USB/IDCU: There are read or write requests pending. error is reported by the USB host" "USB/IDCU: Data underrun error detected. data transfer phase exceeds the USB frame length" "USB/IDCU: Data buffer error has been detected.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Class AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 Error Code 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E 1083_E Sev. error is reported by the USBIO" "USB/IDCU: USB device is already configured. error is reported by the USB bus" "USB/IDCU: Invalid URB function code has been passed. error is reported by the USBIO" "USB/IDCU: Direction of the data transfer request is not supported by that pipe" "USB/IDCU: Number of asynchronous data packets specified in an asynchronous read" "USB/IDCU: Memory resources are exhausted. error is reported by the USB bus" "USB/IDCU: Internal host controller error has been detected" "USB/IDCU: Short transfer has been detected. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 Status desription INFO "USB/IDCU: Unexpected PID detected. error is reported by the USB bus" "USB/IDCU: Asynchronous request has failed. This error is reported by the USBIO driver" "USB/IDCU: The specified pipe was not found in the current configuration" "USB/IDCU: An invalid asynchronous data packet has been specified" "USB/IDCU: There are not enough system resources to complete the operation" "USB/IDCU: Specified interface was not found in the current configuration" "USB/IDCU: Operation cannot be executed while the USB device is in the current state" "USB/IDCU: Invalid parameter has been specified with an IOCTL operation" "USB/IDCU: Evaluation interval of the USBIO DEMO version has expired" "USB/IDCU: Invalid power state has been specified" "USB/IDCU: Device has entered a power down state" "USB/IDCU: API version reported by the USBIO driver does not match" "USB/IDCU: Set configuration operation has failed. error is reported by the USB host" "USB/IDCU: Device is babbling. CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Class AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 AA08 Error Code 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E Sev.dll could not be loaded" "USB/IDCU: Set configuration request has failed" "USB/IDCU: Buffer is too small. error is reported by the USB bus driver USBD" 410 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB bus driver USBD" "USB/IDCU: Invalid pipe flags have been specified" "USB/IDCU: Operation has been timed out. there is no valid handle to execute the operation" "USB/IDCU: Enumeration of the specified devices has failed" "USB/IDCU: Invalid parameter has been passed to a function" "USB/IDCU: Library setupapi. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 0000000000 Status desription INFO "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/IDCU: The specified device object does not exist" "USB/IDCU: Device object was opened. error is reported by the USB bus driver" "USB/IDCU: USB device is gone. error is reported by the USB bus driver USBD" "USB/IDCU: Interface was not found. 2 4 2 2 2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 07 07 07 00 07 07 07 00 01 01 00 07 02 02 04 00 01 08 07 07 01 07 01 01 01 08 07 08 07 07 01 07 07 06 02 01 00 07 07 07 07 07 07 07 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 8000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "DEPOSIT: DEFAULT_WARNING" "DEPOSIT: DEFAULT_ERROR" "DEPOSIT: Device handler was configured to switch LEDs" "DEPOSIT: There is no firmware loaded" "DEPOSIT: Cannot open or read the firmware file on disk" "DEPOSIT: API-Function CscDpsOpen check validity of FW on Disk" "DEPOSIT: Communication problem" "DEPOSIT: Undefined error code" "DEPOSIT: The DLL command specification is invalid" "DEPOSIT: The DLL command specification is invalid" "DEPOSIT: Deposit cassette not installed correctly" "DEPOSIT: Job cannot be executed because envelope in transport path" "DEPOSIT: Envelope jammed in transport path" "DEPOSIT: Operator did not insert envelope during monitoring period" "DEPOSIT: The envelope starting the feed operation" "DEPOSIT: Undefined status Defective sensor" "DEPOSIT: The dispensed envelope has not been" "DEPOSIT: Shutter could not be closed" "DEPOSIT: No envelopes available any longer" "DEPOSIT: Dispenser sensor could not detect the envelope" "DEPOSIT: End of the envelope reached before all chars could be printed" "DEPOSIT: Print unit motor error" "DEPOSIT: Envelope under print head sensor could not detect envelope" "DEPOSIT: Envelope in printer conveyor sensor could not detect envelope" "DEPOSIT: Motor problem of conveyer transport" "DEPOSIT: Envelope in conveyor transport entry sensor could not detect envelope" "DEPOSIT: Envelope in middle of conveyor transport sensor could not detect envelope" "DEPOSIT: Envelope in conveyor transport exit sensor could not detect envelope" "DEPOSIT: No connection between print unit and conveyor transport" "DEPOSIT: No envelope dispenser or programming error" "DEPOSIT: Print head not locked or not available" "DEPOSIT: The inserted envelope is too long" "DEPOSIT: No envelope detected after command" "DEPOSIT: Failure of Envelope in shutter sensor" "DEPOSIT: Error when opening the bandage" "DEPOSIT: Error when closing the bandage" "DEPOSIT: Operator did not remove the offered envelope" "DEPOSIT: An error has occurred in the shutter" "DEPOSIT: An error has occurred on the bandage" "DEPOSIT: Job cancelled by CANCEL" "DEPOSIT: Cannot access full length of data area in a structure" "DEPOSIT: Active function cannot be cancelled" "DEPOSIT: Cannot open the firmware file" "DEPOSIT: Cannot read the firmware file to be loaded" "DEPOSIT: Detect invalid firmware file data" "DEPOSIT: Detect an invalid checksum of the firmware file data" "DEPOSIT: A V24 WRITE command could not be executed" U25604-J-Z745-1-7600 October 2004 411 . Class AA17 is the USB class assigned to Deposit Module. Table 105: Deposit Module (Class: 0017/AA17) Error Error Class Code 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 1420_E 8000_E 8001_E 8002_E 8003_E 8004_E 8005_E 8006_E 8007_E 8008_E 8009_E 800A_E 800B_E 800C_E 800D_E 800E_E 800F_E 8010_E 8011_E 8012_E 8013_E 8014_E 8015_E 8016_E 8017_E 8018_E 8019_E 8020_E 8021_E 8022_E 8023_E 8024_E 8025_E 80F0_E 8102_E 8104_E 8105_E 8106_E 8107_E 8108_E 8200_E Sev.M-Status & M-Data Reference Tables CSC-W32 Error Classes Deposit Module (Class: 0017/AA17) The following table lists the M-Status and M-Data codes assigned to the device class Deposit Module. error is reported by the USB" "USB/DEP: Invalid parameter has been passed. error is reported by the USB host" "USB/DEP: Device is babbling. error is reported by the USB bus" "USB/DEP: There are data transfer requests pending for the device" "USB/DEP: Request has failed. error is reported by the USB host" "USB/DEP: Error code is reserved by the USB host controller driver" "USB/DEP: Error code is reserved by the USB host controller driver" "USB/DEP: Buffer overrun has been detected. error is reported by the USB host" "USB/DEP: FIFO error has been detected. error is reported by the USB bus driver USBD" 412 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB host" "USB/DEP: Endpoint has been halted by the USB bus driver USBD" "USB/DEP: Memory allocation attempt has failed. error is reported by the USB host" "USB/DEP: PID check has failed. error is reported by the USB host" "USB/DEP: Data overrun error detected. error is reported by the USB host controller" "USB/DEP: USB device is not responding. of repeat transmissions reached" "DEPOSIT: Max no. error is reported by the USB host" "USB/DEP: Data underrun error detected. of receive repeats has been reached" "DEPOSIT: Repetition counter expired" "DEPOSIT: The received acknowledge type is invalid" "DEPOSIT: Repetition counter expired" "DEPOSIT: Expected block length does not match transmitted block length" "DEPOSIT: Error occurred during the CscDpsEntry job" "DEPOSIT: The CscDpsEntry job was cancelled by the user" "DEPOSIT: Wrong value for LED in Registry/CSCINI with CSCDPS" "DEPOSIT: V24 Communication timeout" "DEPOSIT: V24 Communication timeout" "DEPOSIT: Communication problem" "USB/DEP: DEFAULT_WARNING" "USB/DEP: DEFAULT_ERROR" "USB/DEP: Unexpected descriptor was reported from USB device" "USB/DEP: Device not found" "USB/DEP: Not enough memory available" "USB/DEP: It was no endpoint found in the descriptor" "USB/DEP: The creation of the list of USB devices failed" "USB/DEP: USB read command could not be executed in the specified monitoring time" "USB/DEP: USB READ command is cancelled by the user" "USB/DEP: The pointer pData is illegal" "USB/DEP: The length in DataSize is 0 (zero)" "USB/DEP: CRC error has been detected" "USB/DEP: Bit stuffing error has been detected" "USB/DEP: DATA toggle mismatch has been detected" "USB/DEP: STALLPID has been detected. error is reported by the USB host controller" "USB/DEP: Unexpected PID detected. 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 07 07 07 07 07 07 07 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "DEPOSIT: A V24 READ command could not be executed" "DEPOSIT: Max no. error is reported by the USB host" "USB/DEP: Buffer underrun has been detected. error is reported by the USB bus" "USB/DEP: Invalid URB function code has been passed.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 0017 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 8201_E 8202_E 8203_E 8204_E 8205_E 8206_E 8207_E 8208_E 8209_E 8300_E FE08_E FE09_E FE85_E DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E Sev. PCI bus latency was too long" "USB/DEP: XACT error has been detected. data transfer phase exceeds the USB frame length" "USB/DEP: Data buffer error has been detected. error is reported by the USB host" "USB/DEP: Buffer was not accessed. error is reported by the USB bus" "USB/DEP: USB frame control is currently not owned.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E Sev. error is reported by the USB bus" "USB/DEP: Bad start frame has been specified. error is reported by the USBIO driver" "USB/DEP: Invalid input buffer has been passed to an IOCTL operation" "USB/DEP: Invalid output buffer has been passed to an IOCTL operation" "USB/DEP: There is not enough system memory available to complete the operation" "USB/DEP: There are read or write requests pending. error is reported by the USBIO" "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" U25604-J-Z745-1-7600 October 2004 413 . error is reported by the USBIO driver" "USB/DEP: USB device has been removed from the system" "USB/DEP: Specified control code is not supported" "USB/DEP: Operation has been timed out. error is reported by the USB bus driver" "USB/DEP: USB frame control is currently owned. This error is reported by the USBIO driver" "USB/DEP: The specified pipe was not found in the current configuration" "USB/DEP: An invalid asynchronous data packet has been specified" "USB/DEP: There are not enough system resources to complete the operation" "USB/DEP: Specified interface was not found in the current configuration" "USB/DEP: Operation cannot be executed while the USB device is in the current state" "USB/DEP: Invalid parameter has been specified with an IOCTL operation" "USB/DEP: Evaluation interval of the USBIO DEMO version has expired" "USB/DEP: Invalid power state has been specified" "USB/DEP: Device has entered a power down state" "USB/DEP: API version reported by the USBIO driver does not match" "USB/DEP: Set configuration operation has failed. error is reported by the USBIO driver" "USB/DEP: Either the handle is already bound to a pipe" "USB/DEP: Handle is not bound to a pipe. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "USB/DEP: Invalid pipe handle has been passed. error is reported by the USB bus" "USB/DEP: Asynchronous request has failed. error is reported by the USBIO" "USB/DEP: The USB device is not configured. error is reported by the USB bus driver" "USB/DEP: Invalid configuration descriptor was reported by the device" "USB/DEP: Operation has failed. error is reported by the USB bus" "USB/DEP: Internal host controller error has been detected" "USB/DEP: Short transfer has been detected. error is reported by the USB" "USB/DEP: Operation is not supported. error is reported by the USBIO driver" "USB/DEP: There are open pipes. error is reported by the USB bus" "USB/DEP: There is not enough bandwidth available. error is reported by the USBIO" "USB/DEP: USB device is already configured. error is reported by the USBIO driver" "USB/DEP: Invalid recipient has been specified" "USB/DEP: Either an invalid request type has been specified" "USB/DEP: Invalid IOCTL code has been specified. error is reported by the USBIO" "USB/DEP: Direction of the data transfer request is not supported by that pipe" "USB/DEP: Number of asynchronous data packets specified in an asynchronous read" "USB/DEP: Memory resources are exhausted. This device is used in CSC450 ATM’s only. error is reported by the USB bus driver USBD" "USB/DEP: Interface was not found.dll could not be loaded" "USB/DEP: Set configuration request has failed" "USB/DEP: Buffer is too small.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 AA17 1081_E 1082_E 1083_E 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E Sev. there is no valid handle to execute the operation" "USB/DEP: Enumeration of the specified devices has failed" "USB/DEP: Invalid parameter has been passed to a function" "USB/DEP: Library setupapi. 2 4 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 03 03 03 03 03 03 03 03 03 03 03 02 MData 0000 0000 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0201 Status desription INFO "VANDAL GUARD: DEFAULT_WARNING" "VANDAL GUARD: DEFAULT_ERROR" "VANDAL GUARD: Unknown internal error has occurred in FW" "VANDAL GUARD: Block ID wrong" "VANDAL GUARD: Device number wrong" "VANDAL GUARD: Job specification wrong" "VANDAL GUARD: Job longer than receive buffer" "VANDAL GUARD: Syntax error in job specification" "VANDAL GUARD: No motion messages when door is opened" "VANDAL GUARD: The hardware error cannot be specified closer" "VANDAL GUARD: E-PROM faulty" "VANDAL GUARD: Processor faulty" "VANDAL GUARD: Checksum error in hardware RAM" "VANDAL GUARD: The door could not be fully opened" 414 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB bus driver USBD" "USB/DEP: Invalid pipe flags have been specified" "USB/DEP: Operation has been timed out. Table 106: Vandal Guard (Class: 0015) Error Error Class Code 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 DEFA_W DEFA_E 8000_E 8020_E 8021_E 8022_E 8023_E 8024_E 8030_E 8040_E 8041_E 8043_E 8044_E 8050_E Sev. error is reported by the USB bus driver USBD" Vandal Guard (Class: 0015) The following table lists the M-Status and M-Data codes assigned to the device class Vandal Guard (Panel Protection Door (PPD)). 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 Status desription INFO "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DEP: The specified device object does not exist" "USB/DEP: Device object was opened. error is reported by the USB bus driver" "USB/DEP: USB device is gone. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DOOR MODULE: DEFAULT_WARNING" "DOOR MODULE: DEFAULT_ERROR" "DOOR MODULE: Block ID wrong" "DOOR MODULE: Device number wrong" "DOOR MODULE: Job specification wrong" "DOOR MODULE: Return buffer too small" "DOOR MODULE: Syntax error in job specification" "DOOR MODULE: The last command has not been processed yet" "DOOR MODULE: The door could not be fully opened" "DOOR MODULE: Door cannot be closed completely Door is blocked" "DOOR MODULE: The hardware error cannot be specified closer" "DOOR MODULE: E-PROM faulty" "DOOR MODULE: EE-PROM faulty" "DOOR MODULE: Processor faulty" "DOOR MODULE: One or more light barriers are dirty or faulty" "DOOR MODULE: Door open/close issued more than 3 times quickly" U25604-J-Z745-1-7600 October 2004 415 . Table 107: Motorized Door (Class: 000E) Error Error Class Code 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E 000E DEFA_W DEFA_E 8020_E 8021_E 8022_E 8023_E 8024_E 8025_E 8030_E 8031_E 8040_E 8041_E 8042_E 8043_E 8045_E 8046_E Sev.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 8051_E 8052_E 8053_E 8054_E 8055_E 80E0_E 80E1_E 80E2_E 80E3_E 80E4_E 80E5_E 80E6_E 80E7_E 80E8_E 80E9_E 80EA_E 80EB_E 80EC_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8109_E Sev. This device is used in CSC250/550 old series ATM’s only. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 01 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 MData 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 0100 Status desription INFO "VANDAL GUARD: Door cannot be closed completely" "VANDAL GUARD: Contact bar without function" "VANDAL GUARD: Light barrier is dirty or faulty" "VANDAL GUARD: Door is difficult to operate" "VANDAL GUARD: Firmware not loaded or started" "VANDAL GUARD: Charaters 1-3 not equal to decimal digits" "VANDAL GUARD: Block length not in valid area (3-250)" "VANDAL GUARD: Block length not equal to received block length" "VANDAL GUARD: Invalid Block ID (N.E)" "VANDAL GUARD: Invalid Device ID" "VANDAL GUARD: Invalid Job ID" "VANDAL GUARD: Invalid Job parameter" "VANDAL GUARD: The last command has not been processed yet" "VANDAL GUARD: Firmware not loaded or started" "VANDAL GUARD: Wrong file length" "VANDAL GUARD: Memory for program module too small" "VANDAL GUARD: Invalid file check charater" "VANDAL GUARD: Hardware not functioning/faulty" "VANDAL GUARD: OS/2 reports error during memory request" "VANDAL GUARD: Wrong/undefined charater job acknowledgment" "VANDAL GUARD: Invalid data in response from peripheral controller" "VANDAL GUARD: Invalid MODSEG ID in FRM file on the system" "VANDAL GUARD: The file *CTF was not found" "VANDAL GUARD: The file *FRM was not found" "VANDAL GUARD: Error when opening a *CTF file" "VANDAL GUARD: Error when opening a *FRM file" "VANDAL GUARD: Invalid data in teh *CTF file" Motorized Door (Class: 000E) The following table lists the M-Status and M-Data codes assigned to the device class Motorized Door. Table 108: Printer (Class: 0032) Error Error Class Code 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 0032 DEFA_W DEFA_E 1420_E 1424_E 8001_E 8002_E 8003_E 8004_E 8005_E 8006_E 8007_E 8008_E 8009_E 800A_E 800B_E 800C_E 800D_E 800E_E 800F_E 8010_E 8011_E 8012_E 8013_E 8014_E 8015_E Sev.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code 000E 000E 000E 000E 000E 000E 000E 8050_E 8051_E 8052_E 8100_E 8101_E 8102_E 8FFF_E Sev. 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "DOOR MODULE: Values of a number of photosensors are below the minimum value" "DOOR MODULE: The light bulb in the cash output tray is defective" "DOOR MODULE: Door does not reach the open end position when opened" "DOOR MODULE: OS/2 report an error when requesting memory for a data buffer" "DOOR MODULE: The status of a non-existent light barrier was requested" "DOOR MODULE: The MDM hardware does not respond at OPEN" "DOOR MODULE: Internal error" Printer (Class: 0032) The following table lists the M-Status and M-Data codes assigned to printer class 0032. 2 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 08 00 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 40000800 00000000 00000000 00000000 20000800 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "PRINTER: DEFAULT_WARNING" "PRINTER: DEFAULT_ERROR" "PRINTER: Communication problem" "PRINTER: The device is currently locked by another user" "PRINTER: If no error found" "PRINTER: If no error found" "PRINTER: Printer control code file could not be opened" "PRINTER: Bad format of the printer control code file" "PRINTER: Invalid format of the macro" "PRINTER: The format file is not available" "PRINTER: OPEN error of the format file" "PRINTER: Bad format of the format file" "PRINTER: Error while transmitting the status buffer" "PRINTER: The print buffer is too small" "PRINTER: No text from the FMT file was found" "PRINTER: If no error found" "PRINTER: If no error found" "PRINTER: If no error found" "PRINTER: Formatting error" "PRINTER: If no error found" "PRINTER: The printer-specific DLL could not be opened" "PRINTER: If no error found" "PRINTER: Unknown string format specification" "PRINTER: If no error found" "PRINTER: If no error found" 416 October 2004 U25604-J-Z745-1-7600 . INI" "JRN/REC: Cannot read control file ND9X. 2 4 2 2 2 2 4 4 2 2 2 2 2 2 2 2 2 2 4 4 2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 MStatus 00 00 00 00 00 16 00 00 00 08 08 08 08 00 08 08 08 05 05 07 07 05 05 07 07 08 08 08 08 08 08 08 08 08 08 08 08 08 08 MData 00000000 00000000 00000000 02000000 02000000 00000002 00000000 00000000 00000000 40000800 40000800 40000800 40000800 00000000 40000800 40000800 40000800 08000000 08000000 40000002 40000002 08000000 08000000 40000000 40000000 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 Status desription INFO "JRN/REC: DEFAULT_WARNING" "JRN/REC: DEFAULT_ERROR" "JRN/REC: Communication problem" "JRN/REC: Receipt paper low warning" "JRN/REC: Journal paper low warning" "JRN/REC: Receipt still in output at OPEN on printer" "JRN/REC: Communication problem" "JRN/REC: Communication problem" "JRN/REC: Wrong macro format" "JRN/REC: Printer hardware error" "JRN/REC: Printer hardware error" "JRN/REC: Loss of command after device error" "JRN/REC: Hardware error in memory test (RAM and ROM)" "JRN/REC: Syntax error in the ESCAPE sequence" "JRN/REC: Parity error" "JRN/REC: A checksum error is set" "JRN/REC: Short-term power failed" "JRN/REC: Paper-out condition or paper jam" "JRN/REC: Loss of command after receipt paper end" "JRN/REC: Receipt paper jam" "JRN/REC: Loss of command after paper jam" "JRN/REC: Paper-out condition or paper jam" "JRN/REC: Loss of command after receipt paper end" "JRN/REC: Journal paper tear" "JRN/REC: Loss of command after receipt paper end" "JRN/REC: The door is not properly closed" "JRN/REC: Loss of command because of open CSC door" "JRN/REC: Printer hardware error" "JRN/REC: Black dot mark not found" "JRN/REC: Cannot open control file ND9X. Table 109: Printer (Class: 0033) Error Error Class Code 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 0033 DEFA_W DEFA_E 0001_W 0001_E 0002_E 0003_E 1017_E 1420_E 8005_E 8009_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8109_E 810A_E 810B_E 810C_E 810D_E 810E_E 810F_E 8110_E 8111_E 8112_E 8201_E 8202_E 8203_E 8204_E 8205_E 8206_E 8207_E 8208_E FE08_E FE09_E Sev.INI" "JRN/REC: Cannot open a file or checksum incorrect" "JRN/REC: Cannot read the file to be loaded" "JRN/REC: File to be loaded has invalid module id" "JRN/REC: Expected response from firmware loader is incorrect" "JRN/REC: Invalid logo type for ND9C" "JRN/REC: Loaded file does not fit to printer hardware" "JRN/REC: V24 Communication timeout" "JRN/REC: V24 Communication timeout" U25604-J-Z745-1-7600 October 2004 417 .M-Status & M-Data Reference Tables CSC-W32 Error Classes Printer ND71/74/98/9A/9C/9E/TH30 (Class: 0033) The following table lists the M-Status and M-Data assigned to printer class 0033. 2 4 2 2 2 2 2 2 MStatus 00 00 00 05 00 23 02 02 MData 0000000000000000 0000000000000000 0200000000000000 4000010000000000 0200000000000000 4000000000000000 4000000000000000 4000000000000000 Status desription INFO "ND79: DEFAULT_WARNING" "ND79: DEFAULT_ERROR" "ND79: Receipt paper low warning" "ND79: Still a receipt in the output chute at an OPEN" "ND79: Receipt paper low warning (last receipt printing)" "ND79: Printer hardware error" "ND79: Loss of command after device error" "ND79: Syntax error in the ESCAPE sequence for loading LOGO" 418 October 2004 U25604-J-Z745-1-7600 . Table 110: Printer (Class: 0034) Error Error Class Code 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 0034 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8109_E 810A_E 810B_E 810C_E 810D_E 810E_E 810F_E 8110_E 8111_E 8112_E Sev. 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 02 02 02 07 04 02 01 05 00 05 00 05 00 01 00 02 04 02 02 MData 0000000000000000 0000000000000000 0200000000000000 0200000000000000 4000000000000000 4000000000000000 4000000000000000 4000000000000000 4000000000000000 0800000000000000 0400000000000000 4000080000000000 4000000100000000 4000010000000000 4000000000000000 4000010000000000 4000000000000000 4000010000000000 4000000000000000 4000100000000000 4000000000000000 4000400000000000 4000000000000000 4000080000000000 4000080000000000 Status desription INFO "ND94: DEFAULT_WARNING" "ND94: DEFAULT_ERROR" "ND94: Paper-low condition" "ND94: Weekend limit reached" "ND94: FF command caused a feed to 1st line of 10th document" "ND94: The set limit for the reject box has been exceeded" "ND94: Error in the low-voltage power supply" "ND94: The carrier was moved manually" "ND94: Error in memory test(RAM and ROM)" "ND94: The paper is used up completely" "ND94: Paper jam. Table 111: Printer (Class: 0035) Error Error Class Code 0035 0035 0035 0035 0035 0035 0035 0035 DEFA_W DEFA_E 0001_E 0003_E 0004_E 8100_E 8101_E 8103_E Sev. bad/missing mark on paper" "ND94: Reset switch on the drum is faulty" "ND94: The cutter is binding" "ND94: Paper jam in paper path" "ND94: FF command caused a feed to 1st line of 10th document" "ND94: Receipt(s) not removed before issuing a new print job" "ND94: Access to a non-existent font module" "ND94: Forms in gripper after 2 reject attempts" "ND94: External light when adjusting photosensor" "ND94: Rocker does not return to home position after cutting" "ND94: Remove stacker door does not open" "ND94: Cheque counter in Backup RAM deleted" "ND94: Print control mark not found" "ND94: Printer hardware error" "ND94: If no error found" Printer ND79 (Class: 0035) The following table lists the M-Status and M-Data codes assigned to printer class 0035.CSC-W32 Error Classes M-Status & M-Data Reference Tables Printer ND75/75S/94 (Class: 0034) The following table lists the M-Status and M-Data codes assigned to printer class 0034. 2 2 2 2 2 2 2 2 2 2 MStatus 02 23 07 07 05 05 00 00 00 00 MData 4000000000000000 4000000000000000 0800000000000000 0800000000000000 4000010000000000 4000010000000000 4000010000000000 4000010000000000 4000010000000000 4000010000000000 Status desription INFO "ND79: A parity error is returned from a printer" "ND79: Short-term power failed on during operation" "ND79: Paper-out condition or paper jam" "ND79: Loss of command after receipt paper end" "ND79: Receipt paper jam" "ND79: Loss of command after paper jam" "ND79: Printer hardware error" "ND79: The printer is in service position" "ND79: Defective control instruction" "ND79: Job lost while printer in service position" Printer ND99 (Class: 0038) The following table lists the M-Status and M-Data codes assigned to printer class 0038. current form still printed" "RECEIPT: Non-existing user-defined character font selected" "RECEIPT: The printer buffer is overflow" "RECEIPT: Loss of command" "RECEIPT: Cutter not in home position" "RECEIPT: Syntax error in ESCAPE sequence for loading user chars." "RECEIPT: Firmware HEX-file SWC728HEX has no valid firmware version" "RECEIPT: Recognized a faulty firmware load file SWC728HEX" "RECEIPT: No firmware is loaded" "RECEIPT: Loaded PRT FW has a release smaller than 0305" "RECEIPT: V24 Communication timeout" "RECEIPT: V24 Communication timeout" "RECEIPT: V24 Communication timeout" "RECEIPT: V24 Communication problem" U25604-J-Z745-1-7600 October 2004 419 .M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 0035 0035 0035 0035 0035 0035 0035 0035 0035 0035 8104_E 8106_E 8107_E 8108_E 8109_E 810A_E 8111_E 8112_E 8113_E 8114_E Sev. 2 4 2 2 2 2 2 2 4 4 2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 MStatus 00 00 00 08 08 08 08 08 00 00 03 03 09 08 08 08 08 05 00 08 08 01 08 08 08 08 08 08 08 08 08 MData 00000000 00000000 02000000 40000000 40000000 40000000 40000000 40000800 00000000 00000000 40000004 40000004 40000000 00000000 00000000 40000000 40000000 08000000 40000000 40000000 40000000 40010000 40000000 40000000 40000000 00000000 40000000 40000000 40000000 40000000 40000000 Status desription INFO "RECEIPT: DEFAULT_WARNING" "RECEIPT: DEFAULT_ERROR" "RECEIPT: Receipt paper low warning" "RECEIPT: API function CscPrtOpen checks FW load file SWC728HEX" "RECEIPT: FW on disk different than SW loaded in printer" "RECEIPT: There is no firmware loaded" "RECEIPT: Loaded PRT FW has a release smaller than 0305" "JRN/REC: Printer hardware error" "PRINTER: Communication problem" "PRINTER: The device is currently locked by another user" "RECEIPT: Hardware error receipt presenter module" "RECEIPT: Printer cannot recognize a top-of-form mark" "RECEIPT: The print head is lifted" "RECEIPT: Syntax error in ESCAPE sequence for loading LOGO" "RECEIPT: A parity error is returned from a printer" "RECEIPT: HW error occured at power ON (self-test)" "RECEIPT: Short-term power failed on during operation" "RECEIPT: Paper-out. Table 112: Printer (Class: 0038) Error Error Class Code 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 0038 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 0005_E 1005_E 1420_E 1424_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8109_E 810A_E 810B_E 810C_E 810D_E 810E_E 810F_E 8110_E FE08_E FE09_E FE0B_E FE85_E Sev. error is reported by the USB host" 420 October 2004 U25604-J-Z745-1-7600 . but monitor not started yet" "ND/TH97: Application tries to start the monitor.CSC-W32 Error Classes M-Status & M-Data Reference Tables Printer ND97/TH97/TP01/NP01/TP05/NP05 (Class: 0039) The following table lists the M-Status and M-Data codes assigned to class 0039. reset switch faulty. Table 113: Printer (Class: 0039) Error Error Class Code 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 0039 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 DEFA_W DEFA_E 1006_E 1427_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8109_E 810A_E 810B_E 810C_E 810D_E 810E_E 8111_E 8112_E 8113_E 8120_E 8121_E 8122_E 8123_E 8124_E 8125_E FE08_E FE09_E FE85_E DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E Sev. error is reported by the USB host" "USB/DOCPRT: Data overrun error detected. dirty sensor" "ND/TH97: "Drum cover not locked. bad/missing mark on paper. drive belt faulty "ND/TH97: The cutter is binding" "ND/TH97: Paper jam in paper path" "ND/TH97: Tray full. 2 4 2 1 2 2 2 2 2 4 4 2 1 1 1 4 1 4 2 4 4 4 4 2 4 4 2 1 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "ND/TH97: Default warning if no CSCW32 error found" "ND/TH97: Default error if no CSCW32 error found" "ND/TH97: Error" "ND/TH97: Printer not accessable. Class AA39 is the USB class assigned to the Statement printer device. error is reported by the USB host controller" "USB/DOCPRT: Unexpected PID detected. error is reported by the USB host" "USB/DOCPRT: PID check has failed. occupied by another user" "ND/TH97: Printer is not able to print graphices" "ND/TH97: Application tries to get a monitor message. transport of more than 10 sheets attempted" "ND/TH97: Sheets where not removed before new print job was issued" "ND/TH97: Wrong access to a non-existent font module" "ND/TH97: Document jam in transport path. error is reported by the USB host" "USB/DOCPRT: Data underrun error detected. 2 reject attempted" "ND/TH97: External light when adjusting the photosensor" "ND/TH97: Rocker does not return to home position after cutting" "ND/TH97: Door is binding. but it is already started" "ND/TH97: Application tries to stop monitor with wrong process" "ND/TH97: Paper jam. paper skew. error is reported by the USB host controller" "USB/DOCPRT: USB device is not responding. stacker door open failure" "ND/TH97: Printer hardware error" "ND/TH97: Reject box overfilled" "ND/TH97: Printer firmware receives an internal SW error" "ND/TH97: Drum cover not closed" "ND/TH97: Selected paper lane not available" "ND/TH97: Paper empty on lane 2" "ND/TH97: Documents not removed before issuing a new print job" "ND/TH97: Print job in graphics mode aborted" "ND/TH97: Internal software error during graphic print job" "ND/TH97: V24 Communication timeout" "ND/TH97: V24 Communication timeout" "ND/TH97: V24 Communication problem" "USB/DOCPRT: DEFAULT_WARNING" "USB/DOCPRT: DEFAULT_ERROR" "USB/DOCPRT: Unexpected descriptor was reported from USB device" "USB/DOCPRT: Device not found" "USB/DOCPRT: Not enough memory available" "USB/DOCPRT: It was no endpoint found in the descriptor" "USB/DOCPRT: The creation of the list of USB devices failed" "USB/DOCPRT: USB read command could not be executed in the specified monitoring time" "USB/DOCPRT: USB READ command is cancelled by the user" "USB/DOCPRT: The pointer pData is illegal" "USB/DOCPRT: The length in DataSize is 0 (zero)" "USB/DOCPRT: CRC error has been detected" "USB/DOCPRT: Bit stuffing error has been detected" "USB/DOCPRT: DATA toggle mismatch has been detected" "USB/DOCPRT: STALLPID has been detected. error is reported by the USB bus" "USB/DOCPRT: Bad start frame has been specified. error is reported by the USBIO" "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" U25604-J-Z745-1-7600 October 2004 421 . error is reported by the USB host" "USB/DOCPRT: FIFO error has been detected. error is reported by the USB" "USB/DOCPRT: Operation is not supported. error is reported by the USB host" "USB/DOCPRT: Buffer underrun has been detected. error is reported by the USB host" "USB/DOCPRT: Device is babbling. error is reported by the USBIO" "USB/DOCPRT: USB device is already configured. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/DOCPRT: Error code is reserved by the USB host controller driver" "USB/DOCPRT: Error code is reserved by the USB host controller driver" "USB/DOCPRT: Buffer overrun has been detected. error is reported by the USBIO driver" "USB/DOCPRT: USB device has been removed from the system" "USB/DOCPRT: Specified control code is not supported" "USB/DOCPRT: Operation has been timed out. error is reported by the USB bus" "USB/DOCPRT: Asynchronous request has failed. error is reported by the USB bus" "USB/DOCPRT: Invalid URB function code has been passed. error is reported by the USB bus" "USB/DOCPRT: Internal host controller error has been detected" "USB/DOCPRT: Short transfer has been detected. error is reported by the USBIO driver" "USB/DOCPRT: Invalid input buffer has been passed to an IOCTL operation" "USB/DOCPRT: Invalid output buffer has been passed to an IOCTL operation" "USB/DOCPRT: There is not enough system memory available to complete the operation" "USB/DOCPRT: There are read or write requests pending. error is reported by the USBIO driver" "USB/DOCPRT: Either the handle is already bound to a pipe" "USB/DOCPRT: Handle is not bound to a pipe. error is reported by the USB bus driver" "USB/DOCPRT: Invalid configuration descriptor was reported by the device" "USB/DOCPRT: Operation has failed. error is reported by the USBIO" "USB/DOCPRT: The USB device is not configured. PCI bus latency was too long" "USB/DOCPRT: XACT error has been detected. error is reported by the USBIO" "USB/DOCPRT: Direction of the data transfer request is not supported by that pipe" "USB/DOCPRT: Number of asynchronous data packets specified in an asynchronous read" "USB/DOCPRT: Memory resources are exhausted. error is reported by the USB bus" "USB/DOCPRT: USB frame control is currently not owned. error is reported by the USB bus driver" "USB/DOCPRT: USB frame control is currently owned. error is reported by the USB host" "USB/DOCPRT: Endpoint has been halted by the USB bus driver USBD" "USB/DOCPRT: Memory allocation attempt has failed. error is reported by the USB bus driver USBD" "USB/DOCPRT: Invalid pipe handle has been passed. error is reported by the USBIO driver" "USB/DOCPRT: There are open pipes. error is reported by the USB host" "USB/DOCPRT: Buffer was not accessed. error is reported by the USB bus" "USB/DOCPRT: There is not enough bandwidth available. error is reported by the USB" "USB/DOCPRT: Invalid parameter has been passed. error is reported by the USB bus" "USB/DOCPRT: There are data transfer requests pending for the device" "USB/DOCPRT: Request has failed. This error is reported by the USBIO driver" "USB/DOCPRT: The specified pipe was not found in the current configuration" "USB/DOCPRT: An invalid asynchronous data packet has been specified" "USB/DOCPRT: There are not enough system resources to complete the operation" "USB/DOCPRT: Specified interface was not found in the current configuration" "USB/DOCPRT: Operation cannot be executed while the USB device is in the current state" "USB/DOCPRT: Invalid parameter has been specified with an IOCTL operation" "USB/DOCPRT: Evaluation interval of the USBIO DEMO version has expired" "USB/DOCPRT: Invalid power state has been specified" "USB/DOCPRT: Device has entered a power down state" "USB/DOCPRT: API version reported by the USBIO driver does not match" "USB/DOCPRT: Set configuration operation has failed. error is reported by the USBIO driver" "USB/DOCPRT: Invalid recipient has been specified" "USB/DOCPRT: Either an invalid request type has been specified" "USB/DOCPRT: Invalid IOCTL code has been specified. data transfer phase exceeds the USB frame length" "USB/DOCPRT: Data buffer error has been detected.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E 1083_E 1084_E Sev. error is reported by the USB bus driver USBD" Printer TH21 (Class: 003E) The following table lists the M-Status and M-Data codes assigned to printer class 003E.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 AA39 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E Sev.dll could not be loaded" "USB/DOCPRT: Set configuration request has failed" "USB/DOCPRT: Buffer is too small. there is no valid handle to execute the operation" "USB/DOCPRT: Enumeration of the specified devices has failed" "USB/DOCPRT: Invalid parameter has been passed to a function" "USB/DOCPRT: Library setupapi. 2 2 2 2 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 M-Status 00 00 00 08 00 08 08 05 08 08 08 08 08 08 08 08 08 08 08 08 M-Data 00000000 00000000 02000000 40000800 00000000 40000800 40000800 80000000 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 40000800 Status desription INFO "TH21: Default warning if no CSC-W32 error found" "TH21: Default error if no CSC-W32 error found" "TH21: Receipt paper low warning" "TH21: Receipt paper empty" "TH21: Cover is properly opened" "TH21: Print head temperature is not ok" "TH21: Power lost" "TH21: Paper jam" "TH21: The cutter is binding" "TH21: Hardware error. error is reported by the USB bus driver" "USB/DOCPRT: USB device is gone. Table 114: Printer (Class: 003E) Error Error Class Code 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E 003E DEFA_W DEFA_E 0001_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8120_E 8121_E 8122_E 8201_E 8202_E 8203_E 8204_E 8205_E 8206_E 8207_E Sev. error is reported by the USB bus driver USBD" "USB/DOCPRT: Invalid pipe flags have been specified" "USB/DOCPRT: Operation has been timed out. cannot read the file to be loaded" "TH21: File to be loaded has invalid module ID" "TH21: The expected response to the FW loader is not correct" "TH21: Invalid Logo type or logo file too big" 422 October 2004 U25604-J-Z745-1-7600 . error is reported by the USB bus driver USBD" "USB/DOCPRT: Interface was not found. error in memory test" "TH21: Communication error with monitoring module if in use" "TH21: No GDI driver WN_TH21 found (when monitoring facility is used)" "TH21: Invalid COM port entry for GDI driver (when monitoring facility is used)" "TH21: Cannot open control file TH21. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/DOCPRT: The specified device object does not exist" "USB/DOCPRT: Device object was opened.INI" "TH21: Cannot read control file TH21.INI" "TH21: Cannot open a file or invalid file name give up" "TH21: Printer hardware error. recognition a mark is not found." "ND9G GDI: Receipt paper jam." "ND9G GDI: The expected response of the Firmware Loader is not correct. 2 2 2 2 2 4 4 4 4 2 4 4 4 2 2 2 2 2 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "ND9G GDI: Default warning if no CSC-W32 error found" "ND9G GDI: Default error if no CSC-W32 error found" "ND9G GDI: Paper-out condition. Table 116: Printer (Class: 0040) Error Error Class Code 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 0040 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0009_E 000A_E 000B_E 000D_E 000E_E 000F_E 0010_E 0011_E 0012_E 0020_E 0021_E 0022_E 0023_E 0024_E 0025_E 0001_W 0002_W Sev." "ND9G GDI: Cannot read the file to be loaded.g." "ND9G GDI: Cannot open a file or checksum of a file to be loaded is not correct." U25604-J-Z745-1-7600 October 2004 423 ." "ND9G GDI: Firmware file data do not reach the firmware controller correctly. 2 2 4 4 MMStatus Data 00 00 00 00 00000000 00000000 00000000 00000000 Status desription INFO "PRT GDI: Default warning if no CSC-W32 error found" "PRT GDI: Default error if no CSC-W32 error found" "PRT GDI: Communication problem" "PRT GDI: Communication problem" Printer Monitor ND9G (Class: 0040) The following table lists the M-Status and M-Data codes assigned to printer class 0040. backup RAM faulty." "ND9G GDI: A parity error is returned from the printer when faulty characters are received." "ND9G GDI: The loaded firmware file does not fit to the printer hardware. The command was sent and could not be correctly executed. Eject)" "ND9G GDI: An error occurred while the required line parameters were being set." "ND9G GDI: By activated mark." "ND9G GDI: An error occurred when the print system was started from the CSC service." "ND9G GDI: Hardware error: error in memory test (RAM and ROM)." "ND9G GDI: Loss of a command." "ND9G GDI: Printer detect unexpected data.M-Status & M-Data Reference Tables CSC-W32 Error Classes Printer Extensions (Class: 003F) The following table lists the M-Status and M-Data codes assigned to printer class 003F. Receipt could not be correctly processed." "ND9G GDI: Terminate applications requiring the printer." "ND9G GDI: A checksum error of the RAM is occurred. Table 115: Printer (Class: 003F) Error Error Class Code 003F 003F 003F 003F DEFA_W DEFA_E 1017_E 1420_E Sev." "ND9G GDI: A WRITE command could not be executed in the specified monitoring time." "ND9G GDI: An internal SW error occurred." "ND9G GDI: Cannot read the firmware file to be loaded." "ND9G GDI: A READ command could not be executed in the specified monitoring time." "ND9G GDI: Wrong value of entry FILE_CTR" "ND9G GDI: No entry FILE1 found in the Registry." "ND9G GDI: Further control commands missing (e." "ND9G GDI: Unexpected data was received. 2 2 4 2 2 4 4 2 4 2 2 2 2 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "TH21 GDI: Default warning if no CSC-W32 error found" "TH21 GDI: Default error if no CSC-W32 error found" "TH21 GDI: Paper-out condition." "TH21 GDI: Power failure during operation or insufficient power supply." "TH21 GDI: The print head temperature is not ok." "TH21 GDI: The cover is properly opened. Receipt could not be correctly processed." Printer System Framework (Class: 0042) The following table lists the M-Status and M-Data codes assigned to printer class 0042." "TH21 GDI: The cutter is binding." "TH21 GDI: A WRITE command could not be executed in the specified monitoring time" "TH21 GDI: A READ command could not be executed in the specified monitoring time" "TH21 GDI: Further control commands missing (e." "TH21 GDI: Receipt paper jam. write request unsuccessful" "PRT GDI: A system error has occurred" "PRT GDI: Unexpected parameter in system call" "PRT GDI: Open failed" "PRT GDI: Start of a print job failed" "PRT GDI: A job has been despooled while another job is still in progress" "PRT GDI: Invalid parameter used in a server function call" "PRT GDI: Client already registered for monitoring" "PRT GDI: The client tried to claim the device twice" "PRT GDI: Invalid client handle used" "PRT GDI: Client not registered for monitoring" 424 October 2004 U25604-J-Z745-1-7600 .g. Table 117: Printer (Class: 0041) Error Error Class Code 0041 0041 0041 0041 0041 0041 0041 0041 0041 0041 0041 0041 0041 0041 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E Sev. Table 118: Printer (Class: 0042) Error Error Class Code 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 0042 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000D_E 000E_E 000F_E 0010_E 0011_E Sev.CSC-W32 Error Classes M-Status & M-Data Reference Tables Printer Monitor TH21 (Class: 0041) The following table lists the M-Status and M-Data codes assigned to printer class 0041. Eject)" "TH21 GDI: An error occurred while the required line parameters were being set." "TH21 GDI: Error in memory test (RAM and ROM)" "TH21 GDI: Unexpected data was received. 2 2 2 2 2 2 2 4 4 2 4 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "PRT GDI: Default warning if no CSC-W32 error found" "PRT GDI: Default error if no CSC-W32 error found" "PRT GDI: Data that are passed to print system are to small" "PRT GDI: Invalid registry parameter" "PRT GDI: Operation not valid or not supported by printer" "PRT GDI: Internal software error" "PRT GDI: Function not allowed in the current context" "PRT GDI: Communication error. the client is not allowed to access the requested operation" "PRT GDI: Access denied.M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code 0042 0042 0042 0042 0042 0042 0042 0042 0012_E 0013_E 0014_E 0015_E 0016_E 0017_E 0018_E 0019_E Sev. 2 4 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "PRT GDI: Start of print system server failed" "PRT GDI: Connection failed. because another client has claimed the device for exclusive access" "PRT GDI: Unknown property" "PRT GDI: The property has an invalid format" "PRT GDI: The property value is invalid" "PRT GDI: An invalid input string has been supplied" U25604-J-Z745-1-7600 October 2004 425 . the printer is unknown" "PRT GDI: Access denied. CSC-W32 Error Classes M-Status & M-Data Reference Tables Printer TP07 GDI (Class: 0044) The following table lists the M-Status and M-Data codes assigned to printer class 0044." "TP07 GDI: Receipt paper jam while printing process" "TP07 GDI: Internal print job timeout has occurred" "TP07 GDI: Power voltage of the printer is too high" "TP07 GDI: Power voltage of the printer is too low" "TP07 GDI: Temperature of the print head is too high" "TP07 GDI: Hardware error" "TP07 GDI: Unexpected data was received" "TP07 GDI: A WRITE command could not be executed in the specified monitoring time" "TP07 GDI: A READ command could not be executed in the specified monitoring time" "TP07 GDI: This message may only occur when controlled print jobs are received" "TP07 GDI: An internal SW error occurred" "TP07 GDI: Printer is in offline state without any specific device error" 426 October 2004 U25604-J-Z745-1-7600 . Table 119: Printer (Class: 0044) Error Error Class Code 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 0044 DEFA_W DEFA_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 0010_E 0011_E 0012_E 0013_E 0015_E 0016_E Sev. 2 4 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 2 4 MStatus 00 00 08 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 40000800 80000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "TP07 GDI: DEFAULT_WARNING" "TP07 GDI: DEFAULT_ERROR" "TP07 GDI: Paper-out condition" "TP07 GDI: Paper jam while cutting the paper" "TP07 GDI: Black dot mark not found" "TP07 GDI: Paper jam after cut receipt in the presenter" "TP07 GDI: Paper jam after cut receipt after reject command. not enough resources to allocate internal memory" "RJ03/TP07/NP07: A READ command could not be executed in the specified monitoring time" "RJ03/TP07/NP07: Code page not available" "RJ03/TP07/NP07: Cannot open image file or invalid file name give up" "RJ03/TP07/NP07: Cannot read the file to be loaded" "RJ03/TP07/NP07: Invalid logo type" "RJ03/TP07/NP07: Printer is in offline state without any specific device error" "RJ03/TP07/NP07: No USB devices of the specified type available" "RJ03/TP07/NP07: Receipt paper out" "RJ03/TP07/NP07: Paper jam while paper cut" "RJ03/TP07/NP07: Carrier does not found the home position" "RJ03/TP07/NP07: Paper jam before cut" "RJ03/TP07/NP07: Black dot mark not found" "RJ03/TP07/NP07: Paper jam after cutting the receipt in the presenter" "RJ03/TP07/NP07: Paper jam after cut receipt after reject command" "RJ03/TP07/NP07: Receipt paper jam while printing" "RJ03/TP07/NP07: Power voltage of printer is too high" "RJ03/TP07/NP07: Power voltage of printer is too low" "RJ03/TP07/NP07: Temperature of print head is too high" "RJ03/TP07/NP07: Hardware error" "RJ03/TP07/NP07: Paper is not at print starting position" U25604-J-Z745-1-7600 October 2004 427 . 4 4 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 02000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "RJ03/TP07/NP07: DEFAULT_WARNING" "RJ03/TP07/NP07: DEFAULT_ERROR" "RJ03/TP07/NP07: Receipt paper low" "RJ03/TP07/NP07: Unexpected data was received" "RJ03/TP07/NP07: Allocation error. Table 120: Printer (Class: 0045) Error Error Class Code 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 0045 DEFA_W DEFA_E 0001_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8000_E 8001_E 8002_E 8003_E 8004_E 8005_E 8006_E 8007_E 8008_E 8009_E 800A_E 800B_E 800C_E Sev.M-Status & M-Data Reference Tables CSC-W32 Error Classes Printer TP07 (Class: 0045) The following table lists the M-Status and M-Data codes assigned to printer class 0045. error is reported by the USB bus" "USB/TP07/NP07: Internal host controller error has been detected" "USB/TP07/NP07: Short transfer has been detected. error is reported by the USB bus driver" "USB/TP07/NP07: Invalid configuration descriptor was reported by the device" "USB/TP07/NP07: Operation has failed. error is reported by the USB bus" "USB/TP07/NP07: Invalid URB function code has been passed. error is reported by the USB host" "USB/TP07/NP07: FIFO error has been detected. Table 121: Printer (Class: AA45) Error Error Class Code AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E Sev. error is reported by the USB host" "USB/TP07/NP07: PID check has failed. error is reported by the USB bus" "USB/TP07/NP07: Asynchronous request has failed. error is reported by the USB host" "USB/TP07/NP07: Data overrun error detected. error is reported by the USB host" "USB/TP07/NP07: Data underrun error detected. error is reported by the USB host" "USB/TP07/NP07: Endpoint has been halted by the USB bus driver USBD" "USB/TP07/NP07: Memory allocation attempt has failed. PCI bus latency was too long" "USB/TP07/NP07: XACT error has been detected. error is reported by the USB bus driver" "USB/TP07/NP07: USB frame control is currently owned. error is reported by the USB bus driver USBD" "USB/TP07/NP07: Invalid pipe handle has been passed. error is reported by the USB bus" "USB/TP07/NP07: There is not enough bandwidth available. 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/TP07/NP07: DEFAULT_WARNING" "USB/TP07/NP07: DEFAULT_ERROR" "USB/TP07/NP07: Unexpected descriptor was reported from USB device" "USB/TP07/NP07: Device not found" "USB/TP07/NP07: Not enough memory available" "USB/TP07/NP07: It was no endpoint found in the descriptor" "USB/TP07/NP07: The creation of the list of USB devices failed" "USB/TP07/NP07: USB read command could not be executed in the specified monitoring time" "USB/TP07/NP07: USB READ command is cancelled by the user" "USB/TP07/NP07: The pointer pData is illegal" "USB/TP07/NP07: The length in DataSize is 0 (zero)" "USB/TP07/NP07: CRC error has been detected" "USB/TP07/NP07: Bit stuffing error has been detected" "USB/TP07/NP07: DATA toggle mismatch has been detected" "USB/TP07/NP07: STALLPID has been detected. error is reported by the USB" "USB/TP07/NP07: Invalid parameter has been passed. error is reported by the USB bus" "USB/TP07/NP07: Bad start frame has been specified. error is reported by the USB host controller" "USB/TP07/NP07: USB device is not responding. error is reported by the USB bus" "USB/TP07/NP07: There are data transfer requests pending for the device" "USB/TP07/NP07: Request has failed. error is reported by the USB bus" "USB/TP07/NP07: USB frame control is currently not owned. error is reported by the USB host" "USB/TP07/NP07: Buffer underrun has been detected. error is reported by the USB host" "USB/TP07/NP07: Device is babbling. data transfer phase exceeds the USB frame length" "USB/TP07/NP07: Data buffer error has been detected.CSC-W32 Error Classes M-Status & M-Data Reference Tables Printer USB/TP07 (Class: AA45) The following table lists the M-Status and M-Data codes assigned to printer class AA45. error is reported by the USB host" "USB/TP07/NP07: Buffer was not accessed. error is reported by the USB" "USB/TP07/NP07: Operation is not supported. error is reported by the USB host" "USB/TP07/NP07: Error code is reserved by the USB host controller driver" "USB/TP07/NP07: Error code is reserved by the USB host controller driver" "USB/TP07/NP07: Buffer overrun has been detected. error is reported by the USB host controller" "USB/TP07/NP07: Unexpected PID detected. error is reported by the USBIO driver" 428 October 2004 U25604-J-Z745-1-7600 . M-Status & M-Data Reference Tables CSC-W32 Error Classes Error Error Class Code AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 AA45 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E 1083_E 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E Sev. error is reported by the USBIO" "USB/TP07/NP07: Direction of the data transfer request is not supported by that pipe" "USB/TP07/NP07: Number of asynchronous data packets specified in an asynchronous read" "USB/TP07/NP07: Memory resources are exhausted. error is reported by the USB bus driver USBD" U25604-J-Z745-1-7600 October 2004 429 . error is reported by the USB bus driver USBD" "USB/TP07/NP07: Invalid pipe flags have been specified" "USB/TP07/NP07: Operation has been timed out. error is reported by the USB bus driver" "USB/TP07/NP07: USB device is gone. This error is reported by the USBIO driver" "USB/TP07/NP07: The specified pipe was not found in the current configuration" "USB/TP07/NP07: An invalid asynchronous data packet has been specified" "USB/TP07/NP07: There are not enough system resources to complete the operation" "USB/TP07/NP07: Specified interface was not found in the current configuration" "USB/TP07/NP07: Operation cannot be executed while the USB device is in the current state" "USB/TP07/NP07: Invalid parameter has been specified with an IOCTL operation" "USB/TP07/NP07: Evaluation interval of the USBIO DEMO version has expired" "USB/TP07/NP07: Invalid power state has been specified" "USB/TP07/NP07: Device has entered a power down state" "USB/TP07/NP07: API version reported by the USBIO driver does not match" "USB/TP07/NP07: Set configuration operation has failed. error is reported by the USB bus driver USBD" "USB/TP07/NP07: Interface was not found.dll could not be loaded" "USB/TP07/NP07: Set configuration request has failed" "USB/TP07/NP07: Buffer is too small. there is no valid handle to execute the operation" "USB/TP07/NP07: Enumeration of the specified devices has failed" "USB/TP07/NP07: Invalid parameter has been passed to a function" "USB/TP07/NP07: Library setupapi. error is reported by the USBIO" "USB/TP07/NP07: USB device is already configured. error is reported by the USBIO" "USB/TP07/NP07: The USB device is not configured. error is reported by the USBIO" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP07/NP07: The specified device object does not exist" "USB/TP07/NP07: Device object was opened. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/TP07/NP07: Invalid input buffer has been passed to an IOCTL operation" "USB/TP07/NP07: Invalid output buffer has been passed to an IOCTL operation" "USB/TP07/NP07: There is not enough system memory available to complete the operation" "USB/TP07/NP07: There are read or write requests pending. error is reported by the USBIO driver" "USB/TP07/NP07: There are open pipes. error is reported by the USBIO driver" "USB/TP07/NP07: Invalid recipient has been specified" "USB/TP07/NP07: Either an invalid request type has been specified" "USB/TP07/NP07: Invalid IOCTL code has been specified. error is reported by the USBIO driver" "USB/TP07/NP07: USB device has been removed from the system" "USB/TP07/NP07: Specified control code is not supported" "USB/TP07/NP07: Operation has been timed out. error is reported by the USBIO driver" "USB/TP07/NP07: Either the handle is already bound to a pipe" "USB/TP07/NP07: Handle is not bound to a pipe. CSC-W32 Error Classes M-Status & M-Data Reference Tables Printer TP06 (Class: 0048) The following table lists the M-Status and M-Data codes assigned to printer class 0048. 4 4 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 02000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "RJ03/TP06/NP06: DEFAULT_WARNING" "RJ03/TP06/NP06: DEFAULT_ERROR" "RJ03/TP06/NP06: Journal paper low" "RJ03/TP06/NP06: Unexpected data was received" "RJ03/TP06/NP06: Allocation error. not enough resources to allocate internal memory" "RJ03/TP06/NP06: A READ command could not be executed in the specified monitoring time" "RJ03/TP06/NP06: Code page not available" "RJ03/TP06/NP06: Cannot open image file or invalid file name give up" "RJ03/TP06/NP06: Cannot read the file to be loaded" "RJ03/TP06/NP06: Invalid logo type" "RJ03/TP06/NP06: Printer is in offline state without any specific device error" "RJ03/TP06/NP06: No USB devices of the specified type available" "RJ03/TP06/NP06: Journal paper out" "RJ03/TP06/NP06: Paper jam while paper cut" "RJ03/TP06/NP06: Carrier does not found the home position" "RJ03/TP06/NP06: Paper jam before cut" "RJ03/TP06/NP06: Black dot mark not found" "RJ03/TP06/NP06: Paper jam after cutting the receipt in the presenter" "RJ03/TP06/NP06: Paper jam after cut receipt after reject command" "RJ03/TP06/NP06: Receipt paper jam while printing" "RJ03/TP06/NP06: Power voltage of printer is too high" "RJ03/TP06/NP06: Power voltage of printer is too low" "RJ03/TP06/NP06: Temperature of print head is too high" "RJ03/TP06/NP06: Hardware error" "RJ03/TP06/NP06: Paper is not at print starting position" 430 October 2004 U25604-J-Z745-1-7600 . Table 122: Printer (Class: 0048) Error Error Class Code 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 0048 DEFA_W DEFA_E 0001_E 8100_E 8101_E 8102_E 8103_E 8104_E 8105_E 8106_E 8107_E 8108_E 8000_E 8001_E 8002_E 8003_E 8004_E 8005_E 8006_E 8007_E 8008_E 8009_E 800A_E 800B_E 800C_E Sev. error is reported by the USB bus" "USB/TP06/NP06: USB frame control is currently not owned. Table 123: Printer (Class: AA48) Error Error Class Code AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 DEFA_W DEFA_E 8000_E 8001_E 8002_E 8003_E 8004_E FE09_E FE0A_E FE89_E FE9C_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000F_E 0010_E 0011_E 0012_E 0013_E 0030_E 0100_E 0200_E 0300_E 0400_E 0500_E 0600_E 0700_E 0800_E 0900_E 0A00_E 0B00_E 0C00_E 0D00_E 0E00_E 0F00_E 1000_E Sev. error is reported by the USB bus" "USB/TP06/NP06: Asynchronous request has failed. error is reported by the USB bus" "USB/TP06/NP06: There is not enough bandwidth available. error is reported by the USB" "USB/TP06/NP06: Invalid parameter has been passed. error is reported by the USB host" "USB/TP06/NP06: Data overrun error detected. error is reported by the USB bus driver" "USB/TP06/NP06: Invalid configuration descriptor was reported by the device" "USB/TP06/NP06: Operation has failed. error is reported by the USB host" "USB/TP06/NP06: FIFO error has been detected. error is reported by the USBIO driver" U25604-J-Z745-1-7600 October 2004 431 . error is reported by the USB bus driver" "USB/TP06/NP06: USB frame control is currently owned. error is reported by the USB host" "USB/TP06/NP06: Buffer underrun has been detected. error is reported by the USB host controller" "USB/TP06/NP06: USB device is not responding. error is reported by the USB host" "USB/TP06/NP06: PID check has failed. error is reported by the USB host controller" "USB/TP06/NP06: Unexpected PID detected. error is reported by the USB bus" "USB/TP06/NP06: Invalid URB function code has been passed. error is reported by the USB host" "USB/TP06/NP06: Data underrun error detected. error is reported by the USB" "USB/TP06/NP06: Operation is not supported. 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/TP06/NP06: DEFAULT_WARNING" "USB/TP06/NP06: DEFAULT_ERROR" "USB/TP06/NP06: Unexpected descriptor was reported from USB device" "USB/TP06/NP06: Device not found" "USB/TP06/NP06: Not enough memory available" "USB/TP06/NP06: It was no endpoint found in the descriptor" "USB/TP06/NP06: The creation of the list of USB devices failed" "USB/TP06/NP06: USB read command could not be executed in the specified monitoring time" "USB/TP06/NP06: USB READ command is cancelled by the user" "USB/TP06/NP06: The pointer pData is illegal" "USB/TP06/NP06: The length in DataSize is 0 (zero)" "USB/TP06/NP06: CRC error has been detected" "USB/TP06/NP06: Bit stuffing error has been detected" "USB/TP06/NP06: DATA toggle mismatch has been detected" "USB/TP06/NP06: STALLPID has been detected. error is reported by the USB bus driver USBD" "USB/TP06/NP06: Invalid pipe handle has been passed. error is reported by the USB host" "USB/TP06/NP06: Device is babbling. data transfer phase exceeds the USB frame length" "USB/TP06/NP06: Data buffer error has been detected. error is reported by the USB bus" "USB/TP06/NP06: There are data transfer requests pending for the device" "USB/TP06/NP06: Request has failed.M-Status & M-Data Reference Tables CSC-W32 Error Classes Printer USB/TP06 (Class: AA48) The following table lists the M-Status and M-Data codes assigned to printer class AA48. PCI bus latency was too long" "USB/TP06/NP06: XACT error has been detected. error is reported by the USB host" "USB/TP06/NP06: Buffer was not accessed. error is reported by the USB host" "USB/TP06/NP06: Error code is reserved by the USB host controller driver" "USB/TP06/NP06: Error code is reserved by the USB host controller driver" "USB/TP06/NP06: Buffer overrun has been detected. error is reported by the USB bus" "USB/TP06/NP06: Internal host controller error has been detected" "USB/TP06/NP06: Short transfer has been detected. error is reported by the USB host" "USB/TP06/NP06: Endpoint has been halted by the USB bus driver USBD" "USB/TP06/NP06: Memory allocation attempt has failed. error is reported by the USB bus" "USB/TP06/NP06: Bad start frame has been specified. error is reported by the USBIO" "USB/TP06/NP06: Direction of the data transfer request is not supported by that pipe" "USB/TP06/NP06: Number of asynchronous data packets specified in an asynchronous read" "USB/TP06/NP06: Memory resources are exhausted.CSC-W32 Error Classes M-Status & M-Data Reference Tables Error Error Class Code AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 AA48 1001_E 1002_E 1003_E 1004_E 1005_E 1006_E 1007_E 1008_E 1009_E 100A_E 100B_E 100C_E 100D_E 100E_E 100F_E 1010_E 1011_E 1012_E 1013_E 1014_E 1015_E 1016_E 1017_E 1018_E 1019_E 101A_E 101B_E 101C_E 101D_E 1080_E 1081_E 1082_E 1083_E 1084_E 1085_E 1086_E 1087_E 1100_E 1102_E 1104_E 1105_E 1106_E 2000_E 3000_E 4000_E 5000_E 6000_E 7000_E Sev. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "USB/TP06/NP06: Invalid input buffer has been passed to an IOCTL operation" "USB/TP06/NP06: Invalid output buffer has been passed to an IOCTL operation" "USB/TP06/NP06: There is not enough system memory available to complete the operation" "USB/TP06/NP06: There are read or write requests pending. error is reported by the USBIO" "USB/TP06/NP06: The USB device is not configured. error is reported by the USBIO driver" "USB/TP06/NP06: USB device has been removed from the system" "USB/TP06/NP06: Specified control code is not supported" "USB/TP06/NP06: Operation has been timed out. there is no valid handle to execute the operation" "USB/TP06/NP06: Enumeration of the specified devices has failed" "USB/TP06/NP06: Invalid parameter has been passed to a function" "USB/TP06/NP06: Library setupapi. error is reported by the USBIO driver" "USB/TP06/NP06: Either the handle is already bound to a pipe" "USB/TP06/NP06: Handle is not bound to a pipe. error is reported by the USB bus driver USBD" 432 October 2004 U25604-J-Z745-1-7600 .dll could not be loaded" "USB/TP06/NP06: Set configuration request has failed" "USB/TP06/NP06: Buffer is too small. error is reported by the USBIO" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: The operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: Operation has failed due to a restriction of the USBIO LIGHT version" "USB/TP06/NP06: The specified device object does not exist" "USB/TP06/NP06: Device object was opened. error is reported by the USB bus driver USBD" "USB/TP06/NP06: Interface was not found. error is reported by the USBIO driver" "USB/TP06/NP06: There are open pipes. error is reported by the USB bus driver" "USB/TP06/NP06: USB device is gone. This error is reported by the USBIO driver" "USB/TP06/NP06: The specified pipe was not found in the current configuration" "USB/TP06/NP06: An invalid asynchronous data packet has been specified" "USB/TP06/NP06: There are not enough system resources to complete the operation" "USB/TP06/NP06: Specified interface was not found in the current configuration" "USB/TP06/NP06: Operation cannot be executed while the USB device is in the current state" "USB/TP06/NP06: Invalid parameter has been specified with an IOCTL operation" "USB/TP06/NP06: Evaluation interval of the USBIO DEMO version has expired" "USB/TP06/NP06: Invalid power state has been specified" "USB/TP06/NP06: Device has entered a power down state" "USB/TP06/NP06: API version reported by the USBIO driver does not match" "USB/TP06/NP06: Set configuration operation has failed. error is reported by the USBIO driver" "USB/TP06/NP06: Invalid recipient has been specified" "USB/TP06/NP06: Either an invalid request type has been specified" "USB/TP06/NP06: Invalid IOCTL code has been specified. error is reported by the USBIO" "USB/TP06/NP06: USB device is already configured. error is reported by the USB bus driver USBD" "USB/TP06/NP06: Invalid pipe flags have been specified" "USB/TP06/NP06: Operation has been timed out. spooler active" "LYNX TRX: Journal printer warning.M-Status & M-Data Reference TablesApplication Error Classes (LYNX error Application Error Classes (LYNX errors) Transaction (Class: 6434) Table 124: Transaction (Class: 6434) Error Error Class Code 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 0001_E 0001_W 0002_E 0003_E 0004_E 0004_W 0005_W 0006_E 0007_E 0008_E 0009_E 000A_W 000B_W 000C_W 000D_W 000E_E 000E_W 0010_E 0010_W 0011_W 0012_W 0013_W 0014_W 0015_W 0015_E 0016_W 0017_W 0018_E 0019_E 0020_W 0021_W 0022_W 0023_W 0024_W 0025_W 0026_W 0027_W 0028_W 0028_E 0029_W 002A_E 002B_E 002C_E 002D_E 002E_E 002F_E 0030_E 0031_E 0032_W 0033_W 0034_W 0035_W Sev. warning" "LYNX TRX: Journal paper low. 0 2 4 4 2 2 4 2 2 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 2 2 4 4 4 2 2 2 2 2 2 2 4 2 2 2 2 MStatus 00 12 07 08 00 00 08 00 00 00 20 00 00 00 20 00 00 00 00 05 00 12 00 00 00 00 00 11 07 13 09 01 01 11 08 01 04 11 11 38 00 00 00 00 00 00 04 06 02 01 02 05 MData 06000000 06000000 40000000 40000000 0007000000000000 0007000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 000000000000000000 00000000 00000000 00000000 0000000000 00000000 00000000 00000000000000000000 00000000000000000000 0000000000000000000000 0001 06000040 01000000000000000000 02000000 02000000 02000000 0200000000000000 0400000000000000000 0000000000 1000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0600000000 000000 000000 0000000000000000000000 0000000000000000000000 000000 000000 000000 000000 000000 000000 000000 000000 Status desription INFO "LYNX TRX: Card was captured" "LYNX TRX: Card was captured" "LYNX TRX: Receipt printer not configured" "LYNX TRX: Statement printer not configured" "LYNX TRX: Statement was retracted" "LYNX TRX: Statement was retracted" "LYNX TRX: Deposit general error" "LYNX TRX: Deposit was cancelled" "LYNX TRX: Deposit timeout" "LYNX TRX: Deposit not configured" "LYNX TRX: Cash dispenser not configured" "LYNX TRX: Journal printer general error" "LYNX TRX: Receipt printer general error" "LYNX TRX: Document printer general error" "LYNX TRX: Card reader general HW error" "LYNX TRX: Journal printer error.DEP: Consumer timeout in screen dialog 906" "LYNX TRX: CAS . error" "LYNX TRX: Receipt paper low" "LYNX TRX: Document paper low" "LYNX TRX: Try to dispense with money in transport" "LYNX TRX: Card write attempt but no track data" "LYNX TRX: CDM shutter error" "LYNX TRX: Deposit bin missing" "LYNX TRX: Deposit jam" "LYNX TRX: Deposit envelope jam" "LYNX TRX: Deposit no envelope" "LYNX TRX: Deposit printer failure" "LYNX TRX: Deposit envelope size" "LYNX TRX: Deposit shutter not close" "LYNX TRX: Deposit bin full" "LYNX TRX: Deposit bin full (ADRS)" "LYNX TRX: Card reader bin overfilled" "LYNX TRX: CAS .CDM: Consumer has cancelled screen dialog 907" "LYNX TRX: CAS .DEP: Consumer has cancelled screen dialog 906" "LYNX TRX: CAS . spooler active" "LYNX TRX: Money was retracted error" "LYNX TRX: Money was retracted warning" "LYNX TRX: Deposit shutter not opened" "LYNX TRX: Panel Protection door problem" "LYNX TRX: Card read threshold" "LYNX TRX: Cassette low" "LYNX TRX: Journal paper low.CDM: Consumer timeout in screen dialog 907" "LYNX TRX: CAS .DOC: Consumer timeout in Screen dialog 909" "LYNX TRX: CAS .DOC: Consumer has cancelled screen dialog 909" "LYNX TRX: Envelope dispenser LOW" "LYNX TRX: Envelope dispenser EMPTY" "LYNX TRX: Envelope dispenser error" "LYNX TRX: Envelope dispenser jam" "LYNX TRX: Envelope dispenser shutter not close" "LYNX TRX: Envelope dispenser shutter not open" U25604-J-Z745-1-7600 October 2004 433 . no bills)" "LYNX WOSA RTC: -316 (Invalid cash unit)" "LYNX WOSA RTC: -315 (Shutter closed)" "LYNX WOSA RTC: -314 (Shutter open)" "LYNX WOSA RTC: -313 (Shutter not open)" "LYNX WOSA RTC: -312 (Invalid retract)" "LYNX WOSA RTC: -311 (Safe door open)" "LYNX WOSA RTC: -310 (Position locked)" "LYNX WOSA RTC: -309 (Invalid position)" "LYNX WOSA RTC: -308 (Documents. error" "LYNX TRX: Journal paper nearly empty. warning" "LYNX TRX: Receipt paper nearly empty" "LYNX TRX: Shutter not close or money jam. 2 2 4 2 2 2 4 4 4 2 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 03 03 41 04 04 00 07 08 08 07 11 10 00 14 03 03 01 14 13 14 34 00 03 03 17 03 04 04 04 04 09 09 MData 01100000000000000000 01100000000000000000 00004000000000000000 00000303030300000000 00000303030300000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 06000000000000000000 02000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "LYNX CDM: Warning not found.Application Error Classes (LYNX errors)M-Status & M-Data Reference Table Error Error Class Code 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 6434 0036_E 0037_E 0037_W 0038_E 0039_E 0040_E 0041_E 0042_E 0043_W 0043_E 0044_E 0045_E 0046_E 0047_E 0048_E Sev. 2 4 2 2 2 4 4 2 2 4 2 2 4 4 4 MStatus 36 05 05 08 12 05 05 12 05 05 02 04 04 04 04 MData 0007000000000000 08000000 08000000 40000800 00000000000000000000 40000800 08000000 06000000 08000000 08000000 0000000000 0000000000 0000000000 0000000000 0000000000 Status desription INFO "LYNX TRX: Statement capture bin full" "LYNX TRX: Journal paper nearly empty. use default entry" "LYNX CDM: Error not found. dispense operation declined" "LYNX TRX: Receipt paper jam or paper empty" "LYNX TRX: Journal paper jam or paper empty" "LYNX TRX: Card was captured after jam" "LYNX TRX: Hard disk free space becomes low" "LYNX TRX: No hard disk free space available" "LYNX TRX: Card write attempted but track not installed" "LYNX TRX: Card write command failed" "LYNX TRX: Card trap active" "LYNX TRX: Mouth piece vandalism" "LYNX TRX: Card reader skimming active" Cash Dispenser (Class: 643A) Table 125: Cash Dispenser (Class: 643A) Error Error Class Code 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 02DF DEFA_W DEFA_E 0001_E 0002_E 0002_W 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E FEB5_W FEB6_W FEC0_W FEC3_W FEC4_W FEC5_W FEC6_W FEC7_W FEC8_W FEC9_W FECA_W FECB_W FECC_W FECD_W FECE_W FECF_W FED0_W FED1_W FED2_W FED2_E Sev. use default entry" "LYNX CDM: Invalid cassette number" "LYNX CDM: Try from empty or low cassette" "LYNX CDM: Not dispenseable" "LYNX CDM: Safe door open during dispense" "LYNX CDM: Reject cassette not operational" "LYNX CDM: Reject cassette full" "LYNX CDM: Max retracts reached" "LYNX CDM: Reject bin missing" "LYNX CDM: Max present errors after dispense" "LYNX CDM: Cash dispenser fatal" "LYNX WOSA RTC: -331 (Order not allowed)" "LYNX WOSA RTC: -330 (Shutter not closed)" "LYNX WOSA RTC: -320 (Denomination error)" "LYNX WOSA RTC: -317 (No documents. bills left)" "LYNX WOSA RTC: -307 (Too many documents)" "LYNX WOSA RTC: -306 (Not dispensable)" "LYNX WOSA RTC: -305 (No currency mix)" "LYNX WOSA RTC: -304 (Invalid mix type)" "LYNX WOSA RTC: -303 (Invalid denomination)" "LYNX WOSA RTC: -302 (Cash unit error)" "LYNX WOSA RTC: -302 return of CheckDispOutput()" 434 October 2004 U25604-J-Z745-1-7600 . 4 2 3 4 2 MStatus 01 02 03 04 05 MData 0000000000000000 000001 0000000000000000 000002 0000000000000000 000003 0000000000000000 000004 0000000000000000 000005 Status desription INFO "LYNX CASHIN: CashIn not operational" "LYNX CASHIN: CashIn input shutter jam" "LYNX CASHIN: CashIn input tray jam" "LYNX CASHIN: CashIn input transport jam" "LYNX CASHIN: CashIn output shutter jam" U25604-J-Z745-1-7600 October 2004 435 . possibly wrong keys" "LYNX SEC: PIN check error. possibly wrong keys" "LYNX SEC: Error while creating host PIN block" "LYNX SEC: Error calculating MAC" "LYNX SEC: Error initializing transaction" CashIn transaction (Class: 6446) Table 127: CashIn transaction (Class: 6446) Error Error Class Code 6446 6446 6446 6446 6446 0001_E 0002_E 0003_E 0004_E 0005_E Sev. cannot dispense" Security Module (Class: 643C) Table 126: Security Module (Class: 643C) Error Error Class Code 643C 643C 643C 643C 643C 0001_E 0002_E 0003_E 0004_E 0005_E Sev. 4 2 2 2 2 MStatus 38 70 70 38 38 MData 00000000 00000000 00000000 00000000 00000000 Status desription INFO "LYNX SEC: Set key error. cannot dispense" "LYNX WOSA RTC: Hardware error. bills left)" "LYNX WOSA RTC: -307 (Too many documents)" "LYNX WOSA RTC: -306 (Not dispensable)" "LYNX WOSA RTC: -305 (No currency mix)" "LYNX WOSA RTC: -304 (Invalid mix type)" "LYNX WOSA RTC: -303 (Invalid denomination)" "LYNX WOSA RTC: -302 (Cash unit error)" "LYNX WOSA RTC: -301 (Invalid teller ID)" "LYNX WOSA RTC: -300 (Invalid currency)" "LYNX WOSA RTC: Hardware error. no bills)" "LYNX WOSA RTC: -316 (Invalid cash unit)" "LYNX WOSA RTC: -315 (Shutter closed)" "LYNX WOSA RTC: -314 (Shutter open)" "LYNX WOSA RTC: -313 (Shutter not open)" "LYNX WOSA RTC: -312 (Invalid retract)" "LYNX WOSA RTC: -311 (Safe door open)" "LYNX WOSA RTC: -310 (Position locked)" "LYNX WOSA RTC: -309 (Invalid position)" "LYNX WOSA RTC: -308 (Documents. device not ready" "LYNX WOSA RTC: -331 (Order not allowed)" "LYNX WOSA RTC: -330 (Shutter not closed)" "LYNX WOSA RTC: -320 (Denomination error)" "LYNX WOSA RTC: -317 (No documents.M-Status & M-Data Reference TablesApplication Error Classes (LYNX error Error Error Class Code 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A 643A FED3_W FED4_W FFF2_W FFF3_W FEB5_E FEB6_E FEC0_E FEC3_E FEC4_E FEC5_E FEC6_E FEC7_E FEC8_E FEC9_E FECA_E FECB_E FECC_E FECD_E FECE_E FECF_E FED0_E FED1_E FED2_E FED3_E FED4_E FFF2_E Sev. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 01 03 03 00 14 03 03 01 14 13 14 34 00 03 03 17 03 04 04 04 04 09 09 01 03 MData 00000000000000000000 00000000000000000000 01100000000000000000 01100000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 01100000000000000000 Status desription INFO "LYNX WOSA RTC: -301 (Invalid teller ID)" "LYNX WOSA RTC: -300 (Invalid currency)" "LYNX WOSA RTC: Hardware error. but L3 notes not returned" "LYNX CASHIN: Good Cashin. all notes retracted" "LYNX CASHIN: Good Cashin. but all notes retracted after consumer timeout" "LYNX CASHIN: CashIn cancelled by consumer. but L2 notes retracted" "LYNX CASHIN: Good Rollback. but L2 notes retracted" "LYNX CASHIN: Rollback failed.Application Error Classes (LYNX errors)M-Status & M-Data Reference Table Error Error Class Code 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 6446 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E 000D_E 000E_E 000F_E 0010_E 0011_E 0012_E 0013_E 0014_E 0015_E 0016_E 0017_E 0018_E 0019_E 001A_E 001B_E 001C_E 001D_E 001E_E 001F_E 0020_E 0021_E Sev. 2 MStatus 77 MData 7000000000 Status desription INFO "LYNX EMV: Chip contact threshold" 436 October 2004 U25604-J-Z745-1-7600 . but L2+L3 notes not returned" "LYNX CASHIN: Good Cashin. but L2+L3 notes not returned" EMV transaction (Class: 6459) Table 128: EMV transaction (Class: 6459) Error Error Class Code 6459 0001_W Sev. host reply not yet received" "LYNX CASHIN: Good Rollback. but L3 notes not returned" "LYNX CASHIN: Good Rollback. 4 4 2 2 3 4 2 2 2 2 4 2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 06 07 08 09 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 MData 0000000000000000 000006 0000000000000000 000007 0000000000000000 000008 0000000000000000 000009 0000000000000000 000010 0000000000000000 000011 0000000000000000 000013 0000000000000000 000014 0000000000000000 000015 0000000000000000 000016 0000000000000000 000017 0000000000000000 000018 0000000000000000 000019 0000000000000000 000020 0000000000000000 000021 0000000000000000 000022 0000000000000000 000023 0000000000000000 000024 0000000000000000 000025 0000000000000000 000026 0000000000000000 000027 0000000000000000 000028 0000000000000000 000029 0000000000000000 000030 0000000000000000 000031 0000000000000000 000032 0000000000000000 000033 0000000000000000 000034 Status desription INFO "LYNX CASHIN: CashIn output tray jam" "LYNX CASHIN: CashIn output transport jam" "LYNX CASHIN: CashIn BIM not operational" "LYNX CASHIN: CashIn retracted" "LYNX CASHIN: CashIn input stacker jam" "LYNX CASHIN: CashIn output stacker jam" "LYNX CASHIN: Hardware error on Drum 1" "LYNX CASHIN: Hardware error on Drum 2" "LYNX CASHIN: Hardware error on Drum 3" "LYNX CASHIN: Hardware error on Drum 4" "LYNX CASHIN: Jam during transport on Drum" "LYNX CASHIN: One CashIn box is now overfilled" "LYNX CASHIN: CashIn boxes are overfilled" "LYNX CASHIN: Metal in CashIn tray detected" "LYNX CASHIN: CashIn reject bin full" "LYNX CASHIN: Security stripe sensor defective" "LYNX CASHIN: Metal sensor defective" "LYNX CASHIN: Escrow empty" "LYNX CASHIN: Error TRX reply buffer" "LYNX CASHIN: Good Rollback. trx not allowed" Electronic Journal (Class: 0091) Table 130: EMV transaction (Class: 0091) Error Error Class Code 0091 0091 0091 0091 DEFA_E 0001_E 0002_E 0003_E Sev. cheque will be captured" "LYNX CHEQUE: Retract error.M-Status & M-Data Reference TablesApplication Error Classes (LYNX error Cheque transaction (Class: 645A) Table 129: Cheque transaction (Class: 645A) Error Error Class Code 645A 645A 645A 645A 645A 645A 645A 645A 645A 645A 645A 645A 645A DEFA_E 0001_E 0002_E 0003_E 0004_E 0005_E 0006_E 0007_E 0008_E 0009_E 000A_E 000B_E 000C_E Sev. check path configuration" "LYNX CHEQUE: Shutter jammed or blocked during MediaIn" "LYNX CHEQUE: General hardware error of CCDM" "LYNX CHEQUE: Safe door open. cheque may be still in IO path" "LYNX CHEQUE: Retract bin full. 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 01 01 02 03 04 05 06 07 08 09 10 11 12 MData 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Status desription INFO "LYNX CHEQUE: Cheque device jammed" "LYNX CHEQUE: Cheque acception error" "LYNX CHEQUE: Error during cheques storing" "LYNX CHEQUE: Error during ejecting cheques" "LYNX CHEQUE: Present timeout. 4 4 4 4 MStatus 07 07 07 07 MData 40000000 40000000 40000000 40000000 Status desription INFO "E-JRN: E-Journal file could not be written" "E-JRN: E-Journal file could not be written" "E-JRN: E-Journal file could not be written" "E-JRN: EJ/SAF-Journal file could not be written" U25604-J-Z745-1-7600 October 2004 437 . no more cheques can be captured" "LYNX CHEQUE: Cheque flush error" "LYNX CHEQUE: Cheque device jammed" "LYNX CHEQUE: Cheque archiving failed. stopped" "WOSA CDM/CRS: V.WOSA Error Classes) M-Status & M-Data Reference Tables WOSA Error Classes) WOSA Cash Dispenser (Class: 00B9) Table 131: WOSA Cash Dispenser (Class: 00B9) Error Error Class Code 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 D010_E D016_E D020_E D025_E D100_E D101_E D105_E D106_E D110_E D120_E D125_E D135_E D136_E D140_E D145_E D146_E D170_E D171_E D175_E D176_E D178_E D179_E D180_E D181_E D182_E D185_E D186_E D187_E D200_E D201_E D202_E D203_E D204_E D205_E D206_E D207_E D210_E D214_E D215_E D216_E D217_E D218_E D219_E D220_E D230_E D231_E D232_E D250_E D255_E D256_E D285_E D286_E Sev.24 line problem master <==> slave" "WOSA CDM/CRS: Slave controller without Firmware" "WOSA CDM/CRS: Safe controller faulty" "WOSA CDM/CRS: Safe controller no booter or faulty" "WOSA CDM/CRS: Counter controller faulty" "WOSA CDM/CRS: Counter controller no booter or faulty" "WOSA CDM/CRS: Firmware not loaded" "WOSA CDM/CRS: Safety switch of safe module open" "WOSA CDM/CRS: Safety switch of counter module open" "WOSA CDM/CRS: Device lock after retract & quit" "WOSA CDM/CRS: Device lock after jam in counter area" "WOSA CDM/CRS: Hardware requirements not ok" "WOSA CDM/CRS: Hardware requirements not ok" "WOSA CDM/CRS: Requirements for BIM missing" "WOSA CDM/CRS: Money jam during cash-in" "WOSA CDM/CRS: Money jam during cash-in" "WOSA CDM/CRS: Money jam during cash-in" "WOSA CDM/CRS: Money jam during cash-in" "WOSA CDM/CRS: Money jam during cash-in" "WOSA CDM/CRS: Money jam during cash-in" "WOSA CDM/CRS: Note jam in safe area cassettes" "WOSA CDM/CRS: Note jam in safe area roller" "WOSA CDM/CRS: Note jam in safe area cassettes" "WOSA CDM/CRS: Note jam in counter area (cash out tray)" "WOSA CDM/CRS: Note jam in counter area (cash out tray)" "WOSA CDM/CRS: Note jam in counter area (cash out tray)" "WOSA CDM/CRS: Switch in safe area faulty/blocked" "WOSA CDM/CRS: Switch in safe area faulty/blocked" "WOSA CDM/CRS: Switch in safe area faulty/blocked" "WOSA CDM/CRS: Switch in safe area faulty/blocked" "WOSA CDM/CRS: Switch in safe area faulty/blocked" "WOSA CDM/CRS: Switch in counter area faulty/blocked" "WOSA CDM/CRS: Switch in counter area faulty/blocked" "WOSA CDM/CRS: Switch in counter area faulty/blocked" "WOSA CDM/CRS: Measurement station in safe area faulty" "WOSA CDM/CRS: Tape sensor in BIM module reports error" "WOSA CDM/CRS: Measurement station in counter area faulty" "WOSA CDM/CRS: BIM reader line faulty" "WOSA CDM/CRS: BIM communication faulty" "WOSA CDM/CRS: BIM note signals missing/inacceptable" "WOSA CDM/CRS: BIM returns error in call response" "WOSA CDM/CRS: Photosensor intensifier faulty" "WOSA CDM/CRS: Switch in safe area faulty / blocked" "WOSA CDM/CRS: Switch in safe area faulty / blocked" "WOSA CDM/CRS: Switch in safe area faulty / blocked" "WOSA CDM/CRS: Transport motor in safe area faulty" "WOSA CDM/CRS: Transport motor in safe area faulty" "WOSA CDM/CRS: Transport motor in safe area faulty" "WOSA CDM/CRS: Error during cash out tray handling" "WOSA CDM/CRS: Error during filling tray handling" 438 October 2004 U25604-J-Z745-1-7600 . 4 4 4 4 4 4 4 4 4 2 2 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 09 09 09 09 09 10 10 09 09 09 01 01 01 01 01 01 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 05 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 0000000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 01100000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "WOSA CDM/CRS: Firmware faulty. stopped" "WOSA CDM/CRS: Booter Firmware faulty. M-Status & M-Data Reference Tables WOSA Error Classes) Error Error Class Code 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 D287_E D295_E D296_E D310_E D320_E D330_E D340_E D405_E D406_E D407_E D408_E D410_E D411_E D420_E D421_E D430_E D431_E D440_E D441_E D451_E D461_E D510_E D520_E D530_E D540_E D605_E D610_E D611_E D620_E D621_E D630_E D631_E D640_E D641_E D651_E D661_E D700_E D705_E D710_E D720_E D730_E D740_E D810_E D820_E D830_E D840_E D901_E D902_E D903_E D904_E D905_E D906_E D907_E D908_E D909_E D910_E D911_E D912_E D913_E D914_E D915_E D916_E Sev. write error" "WOSA CDM/CRS: Roller 4 oder switch faulty" "WOSA CDM/CRS: Roller 5 oder switch faulty" "WOSA CDM/CRS: Roller 6 oder switch faulty" "WOSA CDM/CRS: Photosensor is dirty" "WOSA CDM/CRS: Photosensor is dirty" "WOSA CDM/CRS: Photo or pressure sensor faulty" "WOSA CDM/CRS: Photo or pressure sensor faulty" "WOSA CDM/CRS: Photo or pressure sensor faulty" "WOSA CDM/CRS: Photo or pressure sensor faulty" "WOSA CDM/CRS: Photosensor is dirty" "WOSA CDM/CRS: Photosensor is dirty" "WOSA CDM/CRS: Photosensor is dirty" "WOSA CDM/CRS: Photosensor is dirty" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (counter area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" U25604-J-Z745-1-7600 October 2004 439 . write error" "WOSA CDM/CRS: Roller 3 oder switch faulty" "WOSA CDM/CRS: Cassette 4 faulty. write error" "WOSA CDM/CRS: Roller 1 or switch faulty" "WOSA CDM/CRS: Cassette 2 faulty. write error" "WOSA CDM/CRS: Roller 2 oder switch faulty" "WOSA CDM/CRS: Cassette 3 faulty. 2 2 2 2 2 2 2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "WOSA CDM/CRS: Error during cash out tray handling" "WOSA CDM/CRS: Photosensor of cash out tray covered" "WOSA CDM/CRS: Photosensor of filling tray covered" "WOSA CDM/CRS: Too many bundle reject cassette 1" "WOSA CDM/CRS: Too many bundle reject cassette 2" "WOSA CDM/CRS: Too many bundle reject cassette 3" "WOSA CDM/CRS: Too many bundle reject cassette 4" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: Metal in input tray detected" "WOSA CDM/CRS: Security stripe sensor defect" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: No separation possible" "WOSA CDM/CRS: Too many bad bills cassette 1" "WOSA CDM/CRS: Too many bad bills cassette 2" "WOSA CDM/CRS: Too many bad bills cassette 3" "WOSA CDM/CRS: Too many bad bills cassette 4" "WOSA CDM/CRS: ESCROW faulty (no signals)" "WOSA CDM/CRS: Cassette 1 faulty. WOSA Error Classes) M-Status & M-Data Reference Tables Error Error Class Code 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 D917_E D918_E D919_E D920_E D921_E D922_E D923_E D924_E D931_E D932_E D933_E D934_E D935_E D936_E D941_E D942_E D943_E D944_E D945_E D946_E DF01_E DF03_E FE71_E FE9F_E FEA0_E FEA1_E FEA2_E FEB9_E FEBA_E FEBB_E FEBC_E FEBD_E FEBE_E FEBF_E FEC0_E FEC1_E FEC2_E FEC3_E FEC4_E FEC5_E FEC6_E FEC7_E FEC8_E FEC9_E FECA_E FECB_E FECC_E FECD_E FECE_E FECF_E FED0_E FED1_E FED2_E FED3_E FED4_E FFCA_E FFCB_E FFCC_E FFCD_E FFCE_E FFCF_E FFD0_E Sev. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor is dirty (safe area)" "WOSA CDM/CRS: Photosensor roller1 dirty" "WOSA CDM/CRS: Photosensor roller2 dirty" "WOSA CDM/CRS: Photosensor roller3 dirty" "WOSA CDM/CRS: Photosensor roller4 dirty" "WOSA CDM/CRS: Photosensor roller5 dirty" "WOSA CDM/CRS: Photosensor roller6 dirty" "WOSA CDM/CRS: Wrong position roller1 or 36V missing" "WOSA CDM/CRS: Wrong position roller2 or 36V missing" "WOSA CDM/CRS: Wrong position roller3 or 36V missing" "WOSA CDM/CRS: Wrong position roller4 or 36V missing" "WOSA CDM/CRS: Wrong position roller5 or 36V missing" "WOSA CDM/CRS: Wrong position roller6 or 36V missing" "WOSA CDM/CRS: Metal or/and Stripe sensor defect" "WOSA CDM/CRS: Metal or/and Stripe sensor defect" "WOSA CDM/CRS: Wrong height of note in input tray" "WOSA CDM/CRS: Metal in CashIn tray detected" "WOSA CDM/CRS: Safe door must be closed during this command" "WOSA CDM/CRS: CashIn security failure" "WOSA CDM/CRS: Output position is not empty" "WOSA CDM/CRS: Application or configuration error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Money taken during retract" "WOSA CDM/CRS: Error in bills presentation" "WOSA CDM/CRS: Error in bills presentation" "WOSA CDM/CRS: Error in bills presentation" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: No bills available" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Position locked" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Operator intervention required" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" 440 October 2004 U25604-J-Z745-1-7600 . 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 MStatus 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 MData 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 00000000000000000000 Status desription INFO "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Hardware error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Configuration error" "WOSA CDM/CRS: Application error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Installation error" "WOSA CDM/CRS: Application error" U25604-J-Z745-1-7600 October 2004 441 .M-Status & M-Data Reference Tables WOSA Error Classes) Error Error Class Code 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 00B9 FFD1_E FFD2_E FFD3_E FFD4_E FFD5_E FFD6_E FFD7_E FFD8_E FFD9_E FFDA_E FFDB_E FFDC_E FFDD_E FFDE_E FFDF_E FFE0_E FFE1_E FFE2_E FFE3_E FFE4_E FFE5_E FFE6_E FFE7_E FFE8_E FFE9_E FFEA_E FFEB_E FFEC_E FFED_E FFEE_E FFEF_E FFF0_E FFF1_E FFF2_E FFF3_E FFF4_E FFF5_E FFF6_E FFF7_E FFF8_E FFF9_E FFFA_E FFFB_E FFFC_E FFFD_E FFFE_E FFFF_E Sev. WOSA Error Classes) M-Status & M-Data Reference Tables 442 October 2004 U25604-J-Z745-1-7600 . . Table 12: Envelope Deposit (C) state entries . . . Table 11: Extension state entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . State summary . . . . . . . . Table 21: Close state entries . . . . . . . . . . . . . . . . . . . . . . . . . 20 21 31 34 55 58 59 62 64 67 70 71 72 76 78 81 84 87 90 93 96 99 102 104 . . . . . . . . . . . . . . . . . Read condition entry definitions PIN Entry state entries . Table 16: Amount Entry state entries . . . . . . . . . . . . . . . . Table 22: FIT Switch state entries Table 23: Card Write state entries Table 24: Enhanced PIN Entry state entries U25604-J-Z745-1-7600 October 2004 443 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tables Tables Table 1: Table 2: Table 3: Table 4: Table 5: Table 6: Table 7: Table 8: Table 9: Basic Software of ProCash/NDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ProCash/NDC. . . . . . . . ProConsult/NDC steps belonging to NDC states Card Read state entries . . . . . . . . . Basic Software of ProConsult/NDC Standard fonts table Software structure . . . . . . . . . . . . . . . . . Table 10: Customer Selectable PIN state entries . . . . . . . . . . . . . . . . . . . . . . . . . . Table 14: Preset operation code buffer Extension state table Table 15: Four FDK Select Function state entries . . . . . . . . . . . . . . . . . . . . . . Table 13: Pre-Set Operation Code Buffer state table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 19: Transaction Request state entries . . . . . . . . . . . . . . . . . . . . . . . . Table 17: Amount Check state entries . . . . . . . . . . Table 18: Information Entry state entries . . . . . . . . . . . . . . . . . . . . . . . . . Table 20: Extension state entries . . . . . . . . . . . . . . . . . . . . . . . . . . Table 26: Extension state entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 46: Screen escape sequences . . . Table 49: Downloaded reserved screens supported by Wincor Nixdorf terminals . . . . Table 34: Extension state entries . . Table 38: Audio Control state entries Table 39: Hardware Fitness state entries Table 40: Hardware Fitness Extension state entries . . . . . . . . . . . . . . . . . . . . . . Table 33: FDK Information Entry state entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tables Table 25: Enhanced Amount Entry state entries . . . . . . . . . . . . . . . . . . . . . . . . . . Table 36: Extension state entries Table 37: Extension state entries . . . . . . . . . . . . . . . . . . . . . . . . . Table 29: Card Read . . Table 35: Eight FDK Selection state entries . . . . . . . . . . . . . . . . . . . . . 444 October 2004 U25604-J-Z745-1-7600 . . . . 107 110 112 114 116 119 120 123 126 129 132 135 136 139 142 145 148 152 154 154 157 157 160 161 162 Table 27: Language Code Switch state entries Table 28: Extension state entries . . . .PIN Entry Initiation state entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 44: Screen control characters . . Table 32: FDK Switch state entries . . . . . . . . . . . . . . . . . Table 41: Smart FIT Check State . . . . . . . . . . . . . . . . . Table 30: Extension state entries . . . . . . . . . . . . . . . . . . . . Table 43: Screen control characters cross-reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 48: Default WAVE files for Audio Echo on Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . Table 42: Skip state step . Table 45: Screen escape sequences cross-reference . . . . . . . . Table 31: Language Select From Card state entries . . . . Table 47: Default Voice Message files . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tables Table 50: Timer values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 59: Terminal Command message Table 60: State Tables Load Table 61: Screen Data Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 65: Interactive Transaction Response Table 66: FIT Data Load . . . . Table 62: Configuration Parameters Load Table 63: Enhanced Configuration Parameters Load . Table 64: Option codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 67: Encryption Key Load . . . . . . . . . . . . . . Table 56: Solicited Status message . . . . . . . . . . . . . . . Table 71: Date And Time Load . . . . . . . . Table 55: Transaction Request message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 57: Unsolicited Status message . . . . . . . . . . . . . . . . . . . . Table 73: Specific Command Reject Conditions . 168 189 190 200 206 209 218 223 226 236 239 242 245 249 251 254 258 261 264 267 270 272 275 281 287 296 445 Table 51: Alphabetical FIT references Table 52: FIT fields listed by data track position Table 53: MAC flags definition Table 54: Code conventions . . Table 74: NDC function ID’s assigned to step functions Table 75: Send Options And Timers message format U25604-J-Z745-1-7600 October 2004 . . . . . . . . . . . Table 69: Dispenser Currency Mapping Table Load Table 70: Configuration IDLoad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 68: Extended Encryption Key Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 72: Message Authentication Field Selection Load . . . . . . . . . . . . . . . . . . . . . . . Table 58: Transaction Reply command message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 84: Send Error Log Information . . . . . . . . . . . . . . . . . Table 95: Unsolicited Device Status . . . . . . . . . . . . . . . . . Table 83: Supply Counters . . . . . . . . . . Table 101:Cash Cheque Deposit Module (CCDM) (Classes: 001A/XX1A) 392 446 October 2004 U25604-J-Z745-1-7600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 88: Fitness Data . . . . . . . Table 99: Cash Dispenser V1 (Class: 0007) . . . . . . . . . . . . . . . . . . . . . Table 89: Tamper and Sensor Status Data . . . . . . . . . . . . . . . . . . . . Table 91: Local Configuration Option Digits . . . . . . . . . . . . . . . . . . . . 299 301 304 305 306 307 311 313 316 320 321 324 325 327 328 330 331 332 334 335 364 367 368 379 383 Table 78: Send Configuration Information . . . . . Table 79: Hardware Fitness Table . . . . . . . Table 97: Printer Models . . . . . . . . . .Tables Table 76: Acknowledge And Continue . . . . . . . . . . Table 77: Acknowledge And Stop . Table 90: Software ID and Release Number . . . . . . . . . . . . . . . . . . . . . . . Table 86: Hardware Configuration Data Table 87: Supplies Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 82: Supply Status Device Table . . . . . . . . . . . . . . . . . . Table 96: Electronic Journal Upload message format . . . . . . . . . Table 80: Hardware Fitness Table Enhanced Table 81: Device Configuration Table . . . . . . . . . . . . . . Table 98: NDC Printer control characters . . . . . . . . . . . . . . . . . . . . . . Table 100:Cash Dispenser NG (Classes: 0018/001D)) . . . . . . . . . . . . . . . Table 85: Send Date/Time Info . Table 92: Solicited Status (Device Fault) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 93: Error Severity Table . . . . . . . . . . . . . . . . . . . . . . . . . . Table 94: Supplies Status Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 109:Printer (Class: 0033) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 112:Printer (Class: 0038) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . October 2004 . . Table 125:Cash Dispenser (Class: 643A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 124:Transaction (Class: 6434) . Table 117:Printer (Class: 0041) . . . . Table 111:Printer (Class: 0035) . . . . . . . . . Table 120:Printer (Class: 0045) . . . . . . . . . . . Table 107:Motorized Door (Class: 000E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 115:Printer (Class: 003F) . . . . . . . . . . . . . . . . . . . . . Table 110:Printer (Class: 0034) . . . . . . . . . . . . . . . Table 119:Printer (Class: 0044) . 405 406 407 411 414 415 416 417 418 418 419 420 422 423 423 424 424 426 427 428 430 431 433 434 435 435 447 . . . . . . . . Table 122:Printer (Class: 0048) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 114:Printer (Class: 003E) . . Table 121:Printer (Class: AA45) . . . . . . . . . . . . . . . . . . . . . Table 118:Printer (Class: 0042) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 105:Deposit Module (Class: 0017/AA17) . . . . . . . . . . . . . . . . . . . . . . .Tables Table 102:Encryption Decryption Module (EDM) (Class: 000F) Table 103:Encryption Decryption Software (EDS) (Class: 0011) Table 104:Card Reader (Class: 0008/AA08) . . . . . . . . . . . . . . . . . . . . Table 106:Vandal Guard (Class: 0015) . . . Table 123:Printer (Class: AA48) . . . . . . . . . . . . . . . . . . . . . . . . Table 126:Security Module (Class: 643C) . . . . . . . . . . . . . . . . . . Table 127:CashIn transaction (Class: 6446) U25604-J-Z745-1-7600 . . . Table 113:Printer (Class: 0039) . . . . . Table 108:Printer (Class: 0032) . Table 116:Printer (Class: 0040) . . Table 131:WOSA Cash Dispenser (Class: 00B9) 448 October 2004 U25604-J-Z745-1-7600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tables Table 128:EMV transaction (Class: 6459) . . . . . . . . . . . . . . . . . . . . . . . . 436 437 437 438 Table 129:Cheque transaction (Class: 645A) Table 130:EMV transaction (Class: 0091) . . . . . . . Transaction Reply message accept/reject flowchart . . . . . . . . . . . . . . . . . . . . . . . . 41 206 208 225 286 Transaction message flow Terminal to network messages . . . . . . . . .Figures Figures Figure 1: Figure 2: Figure 3: Figure 4: Figure 5: Terminal operation . . . . . . . . . . . . . . . . . . . . . U25604-J-Z745-1-7600 October 2004 449 . . . . . . . . Network to terminal commands . Figures 450 October 2004 U25604-J-Z745-1-7600 . Abbreviations API ARC ASCII ATM CDM CI CRT CSC CSP DES EBCDIC FDK FIT ID IDCU ITR MAC MDS NCR NDC Application Program Interface Application Return Code American Standard Code for Information Interchange Automated Teller Machine Cash Dispenser Module Customization Image Cathode Ray Tube Customer Service Center Customer Selected PIN Data Encryption Standard Extended Binary Coded Decimal Interchange Code Function Display Key Financial Institution Table IDentification ID Card Unit Interactive Transaction Response Message Authentication Code Modular Delivery System National Cash Register NCR Direct Connect U25604-J-Z745-1-7600 October 2004 451 . Abbreviations OAR PAN PC PCCP PIN POS QLLC SDLC SNA SOH SST TABS Open Account Relationship Primary Account Number Personal Computer PC Configurator Package Personal Identification Number Point of Sales (Cash Registers) Qualified Logical Link Control Synchronous Data Link Control System Network Architecture State Of Health Self Service Terminal Total Automatic Banking System 452 October 2004 U25604-J-Z745-1-7600 . 1/03 1.3/00 1. Reference ProCash/NDC Installation manual ProConsult/NDC Installation manual ProCashIn/Online Installation & Configuration manual GDI Printer Overlay Framework User Guide ProCash/NDC-DDC ProConsult/NDC-DDC WEB-Extensions Installation & Configuration manual Protopas Module Construction Kit Programming Guide Protopas Framework Documentation Programming Guide Protopas Host Protocol and Communication Frameworks Programming Guide VERSION ORDER NUMBER 1.1/00 1. ProCash/DDC and ProConsult/NDC. Link: http://ssp-asw ProCash/NDC and ProConsult/NDC Manuals DESIGNATION ProCash/NDC-DDC Prog. CSC-W32 and AddOn products can be downloaded from the Wincor Nixdorf intranet server.1/00 (PDF file) (PDF file) (PDF file) (PDF file) (PDF file) (PDF file) 4. ProConsult/NDC. which are stored in the Windows registry. ProDevice (WOSA).1/00 (PDF file) (PDF file) (PDF file) ProCash/NDC ProConsult/NDC Installation manuals These two Installation manuals contain detailed descriptions of configuration parameters of ProCash/NDC. U25604-J-Z745-1-7600 October 2004 453 .1/00 4.3/00 1. Further contents are descriptions about several Utilities which are additionally delivered.Related publications Available manuals Basically all the manuals you need to get information about configurations and functionality of ProCash/NDC.3/00 1.3/00 1. ProConsult/DDC.1/00 4. Related publications ProCash/NDC-DDC Programmers Reference This manual gives detailed descriptions about Steps. It also gives detailed descriptions about additional configuration parameters. manual The Installation & Configuration manual contains detailed descriptions how the add on product WEB-Extensions is integrated in ProCash/NDC and ProConsult/NDC. It contains detailed parameter descriptions that are required (mandatory or optional) to enable Windows GDI printing. ProCashIn/Online Inst. With this manual a programmer is able to build up Protopas applications. ProCash/DDC. It also gives detailed descriptions about additional configuration parameters. which are needed to enable the WEB-Extensions. ProConsult/NDC and ProConsult/DDC. which are needed to enable ProCashIn/Online. ProCash/NDC ProConsult/NDC WEB-Extension Inst. Furthermore it gives information about the ProCash/NDC ProConsult/NDC architecture and the connection with Protopas basic frameworks. Prep functions and variables used by ProCash/NDC and ProConsult/NDC. ProTopas Framework Documentation Programming Guide Gives a global overview about the ProTopas Framework architecture and describes the interaction between the different frameworks. 454 October 2004 U25604-J-Z745-1-7600 . & Conf. ProTopas Module Konstruction Kit Programming Guide Describes the Frameworks of the ProTopas Manager and gives detailed API descriptions for the programmer. manual The Installation & Configuration manual contains detailed descriptions how the add on product ProCashIn/Online is integrated in ProCashIn/NDC and ProCashIn/DDC. & Conf. ProTopas Host Protocol and Communication Frameworks ProGramming Guide Describes the API’s of the Communication Frameworks from ProTopas Manager and gives detailed descriptions for the programmer. GDI Printer Overlay Framework User Guide The User Guide describes how GDI print is realised in ProCash/NDC.