Type ofGuidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 1 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) Project Name: Sprint 2.5 TD-LTE Customer Name: Document No. Version Sprint D512241255 0.8 Document Type: Method of Procedure Document Number: D512241255 Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 2 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) Document Revision History Date Rev. 3/17/2014 1 4/10/14 7/15 Originator Summary of Change Pete Mork / Steve Elliston First draft 2 Jason Mackel Language added for SCOP docs and ATP 3 Pete Mork RL45 Updates 8/15/14 4 James Vu Factory SW to PCD4 steps Updates 08/20/14 5 Fahad Faridi Updates for commissioning and post commissioning activities. Included escalation matrix. 8/20/14 6 Jason Mackel Updated ART requirements in section 4 and added ART document in appendix 09/02/14 7 James Vu/ Fahad Faridi Step 11: Added removing IPsec policy during 1st commissioning Step 42,48, 49: Include reference for Site Master sheet for RET angles Page 31 [#4] : Added details for picture upload fields in NOLS 9/3/14 8 James Vu/ Fahad Faridi Step 19: Added new route in routing table to support Traffica Step 20 - 25: Added steps for configuring RF parameters during 2nd commissioning. Step 5 - 8: Added steps to check for CPRI interface using script. Sprint Document Approval Rev. Role Name Signature Date The information in this document is subject to change without notice and describes only the product defined in the introducti on of this documentation. This document is intended for the use of Nokia Solutions and Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified, or transmitted in any form or means without the prior written permission of Nokia Solutions and Networks. The document has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Solutions and Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this document concerning the suitability, capacity, or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively in a separate agreement between Nokia Solutions and Networks and the customer. However, Nokia Solutions and Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Solutions and Networks will, if deemed necessary by Nokia Solutions and Networks, explain issues which may not be covered by the document. Nokia Solutions and Networks will correct errors in the document as soon as possible. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENT OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY MONETARY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This document and the product it describes are considered protected by copyrights and other intellectual property rights according to the appli cable laws. Wave logo is a trademark of Nokia Solutions and Networks Oy. Nokia is a registered trademark of Nokia Corporation. Other mentioned this document may be trademarks of SITE their respective owners, and they are mentioned for identi fication purposes only. Copyright © product Nokianames Solutions andinNetworks 2014 ENGINEERING Copyright © Nokia Solutions and Networks 2014. All rights reserved. D512241255 0.8 Page 2 (34) Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 3 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) Table of Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Introduction ......................................................................................................................................... 4 1.1 MOP Contacts .......................................................................................................................... 4 1.2 NSN Project Escalation Contacts .............................................................................................. 4 MOP Work Tasks Summary, Responsibilities & Assumptions ......................................................... 6 2.1 C&I Pre-requisites ..................................................................................................................... 6 2.2 Commissioning and Integration Tasks ....................................................................................... 6 2.3 Training & Insurance Requirements .......................................................................................... 7 Work Task Execution .......................................................................................................................... 7 3.1 Required Tool & Test Equipment Check List.............................................................................. 7 3.2 Detailed Work Task Instructions ................................................................................................ 7 Table 3: NSN project contact list .......................................................................................................... 26 Post C&I checklist and SCOP UPLOAD............................................................................................ 28 Appendix a: C&I Troubleshooting Guide ......................................................................................... 33 Appendix B: ENB LOCK UNLOCK PROCEDURE ............................................................................. 33 Appendix C: TCP/IP Settings ............................................................................................................ 33 Appendix D: FSIH Port Diagram ....................................................................................................... 34 Appendix E: ART Overview ............................................................................................................... 34 Appendix F: SITE MASTER SHEET (For RET Angles) ..................................................................... 34 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Page 3 (34) Table 1: MOP contact list.Type of Guidelines -Number Revision . responses may take 2-5 working days. This document is generated by NSN and shared with Sprint for consultation and Sprint approval. For all technical issues (C&I / ATP failures) Nokia Tier 2 Support should be contacted according to corresponding markets listed in Table 3: NSN project contact list. problems or concerns. including work tasks and checks required to successfully commission and integrate the NSN TD-LTE BBU (FSIH) and RRUs (FZHJ). reference the MOP document and version # and the applicable page(s). Table 2: Technical escalation contact list.2 NSN Project Escalation Contacts If there are issues. In all correspondence.com Sprint Nokia Note: Above is for documentation purposes. collectively known as eNodeB (eNB).faridi@nsn. an escalation should be made to one of the regional project directors. Company Name Title Contact Phone Nokia Fahad Faridi National Technical Manager 847-531-3137 Nokia Frederick Mckinlay RAN Technical Manager 425-205-7818 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. queries or corrections required to this MOP. problems or concerns.1 MOP Contacts Contact the following when there are any concerns. 1. For training and technical support.Number Document Method of D512241255 0. please contact your relevant support organizations.5 Commissioning & Integration MOP . the Nokia project manager should be contacted immediately. this should be raised to the identified contacts in this document within 2 working days of identifying. Company Name Contact Email Fahad Faridi fahad. Nokia Solutions & Networks (NSN) shall not be responsible or accountable for any information taken from this document which is subsequently used by any other party other than Sprint and NSN directly.BBU (FSIH) & RRU (FZHJ) 1. This document and information contained within shall not be shared or distributed outside of Sprint without Nokia Solutions and Networks prior written consent. If there are any concerns or changes required to this MOP.8 Procedure Page 4 of 34 Date: 9/4/2014 Title 2. an escalation should be made to one of the following Technical project managers.8 Page 4 (34) . If Nokia Tier 2/OSS Support is not addressing issues. problems or concerns that are not being addressed by installation engineers. INTRODUCTION This document details the Method of Procedure (MOP). 1. In the unlikely event that the NSN project manager is not addressing issues. Number Document Method of D512241255 0.5 Commissioning & Integration MOP . Market South West Florida Tampa Jacksonville Nokia Market PM Nokia Regional Director Joe Meilinger Cell: 407-284-7812 Nokia Tier 2 Support Siraj Sindhi Cell: 2149148768 Orlando Nashville West Kentucky Memphis Atlanta / Athens Miami / West Palm Arkansas Mississippi New Orleans Kansas Dave Romagnia Cell: 615-335-6815 OSS Support Jeffery San-Luis ROC Central Number : 972-374-0871 Jason Mackel Cell: 954-214-2960 James Vu Cell: 469 879 3692 Carla Pratcher Cell: 770-337-1686 Steve Emberlin Cell: 954-439-5353 Rick Reveley Cell: 313-408-7350 Missouri Albuquerque Austin South Texas Rafe Schenouda Cell: 972-693-6324 Steve Holden Cell: 571-201-2139 San Antonio Houston DFW West Texas Manohar Gotgi Cell: 214 912 2154 Anthony Chavez/ Ramiro Alaniz ROC Central Number : 972-374-0871 Brandon Zobisch Cell: 405-762-3737 Mike Moser Cell: 972-693-8482 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Page 5 (34) .Type of Guidelines -Number Revision .BBU (FSIH) & RRU (FZHJ) Table 3: NSN project contact list.8 Procedure Page 5 of 34 Date: 9/4/2014 Title 2. NSN D 2 Verify fiber connectivity to ports 1-6 on FSIH NSN D 3 Power on FSIH (BBU). In addition to work Sprint or Ericsson may need to carry out (preparation).5 Commissioning & Integration MOP . right side.Number Document Method of D512241255 0. 1. RESPONSIBILITIES & ASSUMPTIONS 2. and FZHJ (RRU) units NSN D 4 Successfully log into the FSIH NSN D 5 Commission TRS and wait until all FZHJ are detected and FYGE self survey is completed NSN D 6 Commission BTS NSN D NSN D NSN D NSN D 7 8 9 Complete software upgrade of FSIH and FZHJ units using the latest project approved software release Move optical cables to the required ports per approved software release Commission all ALDs (Antenna Line Device) including RET ACUs (Antenna Control Unit) 10 Save a copy of the Site Commissioning File NSN D 11 Save a copy of the Backup Commissioning File NSN D 12 Save a copy of the BTS Site Manager Snapshot (Current Data Only) NSN D Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. 2.5 BBU/RRUs shall not commence until all 2.8 Procedure Page 6 of 34 Date: 9/4/2014 Title 2. there is an NSN installation Method of Procedure (MoP) for each of the following site types. Ericsson Indoor cabinet (Sprint shelter site) 3. and CSR.Type of Guidelines -Number Revision . which should be referenced concerning what is required to make the site ready for 2. MOP WORK TASKS SUMMARY. FYGE (GPS box).5 C&I.8 Page 6 (34) . The C&I Engineer must have a copy of the Sprint RFDS. NSN Outdoor Growth Cabinet (sites that required an expansion cabinet) The C&I Engineer must have access to the site specific SCF file required for commissioning the site (Downloaded to PC) before C&I can start.2 Commissioning and Integration Tasks The tasks indicated in the table below represent the items to be conducted by the BTS engineer/technician and will result in the commissioning and integration of the site.5 hardware preparations and installation has been successfully completed. # Work task Responsible for completing work Work carried out during 1 Take before photos inside the Ericsson 6102 cabinet clearly displaying the left side. and the site is ready for C & I to commence.BBU (FSIH) & RRU (FZHJ) 2.1 C&I Pre-requisites Commissioning and Integration (C&I) of the 2. Ericsson Outdoor cabinet (RBS 6102) 2. NOK.Number Document Method of D512241255 0. follow these instructions step by step.Sign in on the site log book .BBU (FSIH) & RRU (FZHJ) 13 Call ROC (OSS Support) for pushing eCSFB Parameters before ATP testing NSN D 14 Execute ATP and upload logs NSN D M = Maintenance window (service effecting work activity) D = Done at any time.Locate the Antenna and RET Serial Number information left by the GC (Tower Crew) Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. N/A or note) 3. including during normal business hours or prior to maintenance window 2. All persons carrying out works on site shall be suitability insured.Type of Guidelines -Number Revision . WORK TASK EXECUTION 3.Request NOC engineer to identify status of CDMA & LTE equipment for alarms .Identify site ID & inform NOC of planned activities . Step Step Description Task Status Arrival On-site 1 Call the Sprint NOC at 1-866-400-6040 Options 2 + 6 .5 Commissioning & Integration MOP .1 Required Tool & Test Equipment Check List Check status # Tool or test equipment 1 Laptop with current project approved eNB software and BTS Site Manager 2 Ethernet cable 3 Fiber Cleaner (Cletop or similar) (OK.8 Page 7 (34) .8 Procedure Page 7 of 34 Date: 9/4/2014 Title 2.2 Detailed Work Task Instructions Upon arrival at site.Locate the hybrid & fiber test results left by the GC (Tower Crew) . 3.Record any alarms observed by the NOC engineer .3 Training & Insurance Requirements Suitable training shall be completed and passed (certified to use this MOP) by all C&I engineers executing this MoP. 5 units and cabling (1-3 photos). Software Verification 1 2 Connect laptop to the FSIH System Module (BBU) with standard Ethernet cable. Photo of cabinet with 2. Connect one end to the PC Ethernet port and the other end to the FSIH System Module (BBU) LMP port. (See Appendix C for TCP/IP settings) Launch BTS Site Manager from your PC Log in to BTS Site Manager.0_BTSSM_1311_062_00 LNT4.5 Commissioning & Integration MOP .Number Document Method of D512241255 0.0_ENB_1311_349_96 LNT4. IP Address = Local (No IP address required if connecting locally) Username = Nemuadmin Password – nemuuser 3 Click “Accept” to continue Check Software version which come pre-installed with FSIH: Pre-installed version BTS Site Managers Required Next Step LNT4.8 Page 8 (34) .Type of Guidelines -Number Revision . Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.BBU (FSIH) & RRU (FZHJ) 2 Visually inspect the hardware installation for obvious errors or issues 3 Take pre-C&I photographs.8 Procedure Page 8 of 34 Date: 9/4/2014 Title 2.0_BTSSM_1311_095_00 5 4 Other Contact Nokia Centralized Support Team for further instructions before proceeding Important: Un-install any version of BTS Site Manager not listed above before proceeding to next step. txt is CPRI Unit. There will be one of two messages in the output.Type of Guidelines -Number Revision . change to OBSAI now!. change to OBSAI now! 7 8 If the message in the output.8 Procedure Page 9 of 34 Date: 9/4/2014 Title
[email protected] Document Method of D512241255 0.7z to your laptop. no need to change! CPRI unit.8 Page 9 (34) .txt file.bat is completed check the output.txt file.txt file of the script can be found in same folder as the script.7z is included in the C&I Document Pack zip file. please return the serial and version number to patrick.BBU (FSIH) & RRU (FZHJ) Hardware Detection 5 Copy and unzip AutoScriptForCustomerUsing (0.11).11).0.5 Commissioning & Integration MOP .com. Double click file CheckLoadIndication4OBSAI. The output. 9 Make sure that all 6 fiber connections from FZHJs (RRHs) are connected to ports 1 to 6 on FSIH (System Module) Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.bat following output will display when script execution will complete 6 Once CheckLoadIndication4OBSAI.0. AutoScriptForCustomerUsing (0. OBSAI unit. click on the file to load.BBU (FSIH) & RRU (FZHJ) Commission TRS by selecting “Commissioning “.5 Commissioning & Integration MOP . select “Template”.Number Document Method of D512241255 0.Type of Guidelines -Number Revision . 10 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. Click “Browse” and go to where the SCF file is stored.8 Procedure Page 10 of 34 Date: 9/4/2014 Title 2. unchecked “BTS”.8 Page 10 (34) . 5 Commissioning & Integration MOP .Number Document Method of D512241255 0.8 Page 11 (34) .Type of Guidelines -Number Revision .8 Procedure Page 11 of 34 Date: 9/4/2014 Title 2.BBU (FSIH) & RRU (FZHJ) Click Next until you reach IP Security page. (Refer to Appendix A: C&I Troubleshooting Guide) Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. RFM will be detected but there is fault 23 reported due to incompatible version. Select Policy and Click Delete Policy 11 Click “next” to “Send Parameters” page then click “ Send Parameters” 12 13 Wait for GPS self survey to complete (This step may take around 30 minutes) Check BTS status and RRU status after auto reset. 14 The BTS status should be integrated. do not begin software upgrade or commissioning. If all hardware is not detected. After auto reset the GPS will come up and site goes to synchronized status. If there is a IP Security Policy listed under Policies. Wait for up to 10 min. 8 Page 12 (34) . Verify the site information on the right side “File Details” is correct and click “open”. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.BBU (FSIH) & RRU (FZHJ) Commissioning From the main menu on the left click on “Commissioning”.Type of Guidelines -Number Revision .Number Document Method of D512241255 0. 15 Select the following and browse to your site specific SCF (Site Configuration File) 16 17 Select the SCF file that was created for the site you are commissioning.8 Procedure Page 12 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP . BBU (FSIH) & RRU (FZHJ) Click Next until you reach IP Security page.Type of Guidelines -Number Revision .8 Procedure Page 13 of 34 Date: 9/4/2014 Title 2.Number Document Method of D512241255 0. Select Policy and Click Delete Policy 18 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. If there is a IP Security Policy listed under Policies.8 Page 13 (34) .5 Commissioning & Integration MOP . Number Document Method of D512241255 0.88.43.46.43.88.46.5 Commissioning & Integration MOP .255.254.43.43.0 10.0 10. Add a new route based on following settings: Destination: Lookup IP address in Table A according to your market Netmask : 255.88.43.88.88.88.0 10.0 10.0 Gateway: Same as management plane CSR gateway (see figure below) 19 Market South West Florida Tampa Jacksonville Orlando Nashville West Kentucky Memphis Atlanta / Athens Miami / West Palm Arkansas Mississippi New Orleans Kansas Missouri Albuquerque Austin South Texas San Antonio Houston DFW West Texas IP Address 10.46.88.0 10.88.43.0 10.8 Page 14 (34) .BBU (FSIH) & RRU (FZHJ) Click Next until you reach IPv4 Routing page.88.0 10.0 10.0 10.88.88.46.0 10.8 Procedure Page 14 of 34 Date: 9/4/2014 Title 2.88.88.0 Table A Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.0 10.0 10.0 10.0 10.88.46.46.43.46.88.46.0 10.88.0 10.43.43.0 10.88.88.88.0 10.46.46.0 10.46.43.88.0 10.88.Type of Guidelines -Number Revision . 8 Page 15 (34) . - Check Carrier Power and select 5W as below: Repeat step 15 for Beta sector (50). and EARFCN for each sector as below: Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.1 antennas Click Next to reach the LTE Carriers Page enter Frequency Band.Type of Guidelines -Number Revision .5 Commissioning & Integration MOP . FZHJ 1.7.Number Document Method of D512241255 0.1 antennas Repeat step 15 for Gamma Sector (51). Bandwidth.11. . FZHJ 1.8 Procedure Page 15 of 34 Date: 9/4/2014 Title 2.Check and fill in antennas (FZHJ 1.9.BBU (FSIH) & RRU (FZHJ) Click Next until you reach the Cell Resources page.1) data for Alpha Sector (49) as below: 20 21 22 23 - Check MIMO settings and select Dynamic Open loop MIMO. Type of Guidelines -Number Revision .Number Document Method of D512241255 0.5 Commissioning & Integration MOP . DC Voltage should be unchecked.8 Procedure Page 16 of 34 Date: 9/4/2014 Title 2. 24 25 Click Next until you reach Antenna Line Settings page enter data as below for all antennas: Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Page 16 (34) .BBU (FSIH) & RRU (FZHJ) Click Next until you reach the Antenna line management menu and verify that “3GPP/AISG Communication” is enabled on antenna line 1 for each RRH. This will allow the RET ACU to be detected after the site is commissioned. Type of Guidelines -Number Revision .8 Page 17 (34) .5 Commissioning & Integration MOP .8 Procedure Page 17 of 34 Date: 9/4/2014 Title 2.Number Document Method of D512241255 0.BBU (FSIH) & RRU (FZHJ) Click Next until following page with all Parameters will be reached 26 Modify following parameters under each LNCEL: Object Name 27 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. Number Document Method of D512241255 0.BBU (FSIH) & RRU (FZHJ) Parameter Name Select R81xCsfbEnforced Select false Select false Click Next until you reach the page that allows you to send parameters and click the “Send Parameters” button.8 Page 18 (34) .8 Procedure Page 18 of 34 Date: 9/4/2014 Title 2. 28 29 Once commissioning is complete.5 Commissioning & Integration MOP . you will have the option to save a copy of the commissioning report. Select the “Save As” option and save this report to your PC Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.Type of Guidelines -Number Revision . If minimum satellite requirements are not met.Number Document Method of D512241255 0.BBU (FSIH) & RRU (FZHJ) as part of the site acceptance close out package. If hardware installation is correct.Type of Guidelines -Number Revision . Contact PM if GPS postion is a concern. If this alarm is encountered. 32 Verify there is no “Software Incompatibility” alarms post software upgrade.8 Procedure Page 19 of 34 Date: 9/4/2014 Title 2. Note: Wait 10 minutes after software upgrade is 100% COMPLETE before proceeding to next step. 30 Software Upgrade 31 From the main menu click “Software”. then “Update Software to BTS”. check the position of the GPS antenna – and that it has a clear view to the sky.5 Commissioning & Integration MOP . check the hardware installation.0_BTSSM_1311_536_03). Update the software to the project approved software release (LNT4. Click on the object FYGA and verify GPS is receiving signal from satellites. Verify a minimum of 5 satelites are required with minimum signal strength of 6. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Page 19 (34) . first move the fibers according to step 22 and then follow the steps to clear this alarm. 8 Procedure Page 20 of 34 Date: 9/4/2014 Title 2. 35 After FZHJs are detected.5 Commissioning & Integration MOP . re-commission site using Reconfiguration option. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.10 and 5.Type of Guidelines -Number Revision .Number Document Method of D512241255 0.4 (beta sector) to 9.6 ( gamma sector) to 11.2 ( alpha sector) to 7. 3. 33 Move optical cables from ports 1. A second software upgrade is required to clear this alarm.8.12 as shown in following diagram: 34 NOTE: If you encounter Software incompatibility alarm repeat step 19.BBU (FSIH) & RRU (FZHJ) Verify no other alarms are present before proceeding to the next step.8 Page 20 (34) . 8 Page 21 (34) .5 Commissioning & Integration MOP .Type of Guidelines -Number Revision .Number Document Method of D512241255 0.BBU (FSIH) & RRU (FZHJ) After commissioning is completed verify that correct ports are being shown in BTS Site Manager after clicking each FZHJ. 36 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Procedure Page 21 of 34 Date: 9/4/2014 Title 2. This allows you to commission the RETs only. RET Commissioning Commission all RET ACU (Antenna Control Units).8 Procedure Page 22 of 34 Date: 9/4/2014 Title 2. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.BBU (FSIH) & RRU (FZHJ) 37 Verify “OAM connected” is displayed in lower right corner of BTS Site Manager. 42 Note: Electrical tilts for RETs are set in the warehouse before the antennas are shipped to market. ALD alarms will be resolved in the next steps during RET commissioning. From the main menu on the left click on “Commissioning”.Type of Guidelines -Number Revision . It is highly recommended to save a Backup Commissioning file by clicking the “Backup Commissioning Files” button before proceeding.5 Commissioning & Integration MOP . Please refer to Appendix A: C&I Troubleshooting Guide for issue resolution details. If OAM connected does not display within 10 minutes refer to troubleshooting appendix. 40 41 Verify all sectors are “On Air” and the site has no alarms other than ALD (Antenna Line Device). and FZHJ and verify working state is “working”.Number Document Method of D512241255 0. Verify “TRS Commissioned” is displayed in lower right corner of BTS Site Manager 38 Verify “On Air” is displayed in lower right corner of BTS Site Manager 39 Click on each hardware object FSIH. Example FZHJ displayed below. If no new RET information is provided please commission RETs with the current settings. If your site is listed in the “Site Master sheet” please commission the RETs and then reset the angles to the new angels 43 Select the following option to reconfigure the BTS. FBIH. If you encounter any other alarms do not proceed.8 Page 22 (34) . Number Document Method of D512241255 0.5 Commissioning & Integration MOP .Type of Guidelines -Number Revision . Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. Assign each RET to the corresponding antenna 44 45 After each RET has been assigned to its corresponding antenna click “Next” until you reach the send parameters page. Click “Send Parameters” (Only Changes is default).BBU (FSIH) & RRU (FZHJ) Click “Next” until you reach the RET Settings page.8 Procedure Page 23 of 34 Date: 9/4/2014 Title 2.8 Page 23 (34) . 5 Commissioning & Integration MOP .BBU (FSIH) & RRU (FZHJ) Once the RETs are commissioned they need to be calibrated and the electrical tilt needs to be set per the Site Information Package. NOTE: You can select all RETs for calibration at the same time. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Page 24 (34) . To calibrate each RET ACU. go to the main menu Antenna and click on “RET Settings” 46 47 Select the RET you wish to calibrate by clicking the check box and then click send.Type of Guidelines -Number Revision .8 Procedure Page 24 of 34 Date: 9/4/2014 Title 2.Number Document Method of D512241255 0. 8 Procedure Page 25 of 34 Date: 9/4/2014 Title 2. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. Double click inside the “Angle” box. verify the eNodeB is alarm free.5 Commissioning & Integration MOP . Example below.Number Document Method of D512241255 0.8 Page 25 (34) . calibrated.Type of Guidelines -Number Revision . and electrical tilts are set according to the Site Master Sheet.BBU (FSIH) & RRU (FZHJ) After the RETs are calibrated you will be able to set the desired electrical down tilt. enter the desired angle value according to Site Master Sheet [APPENDIX F] and then click send. 48 49 After the RETs are commissioned. Notify OSS Support to initiate eNB Object Creation and eCSFB Parameter Push in NetAct OSS (EMS). This will be required for site acceptance and close out package.Number Document Method of D512241255 0.5 Commissioning & Integration MOP .2 NSN Project Escalation Contacts Table 3: NSN project contact list Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. 51 OSS Support numbers are listed in following section of this MOP 1.Type of Guidelines -Number Revision .8 Page 26 (34) .BBU (FSIH) & RRU (FZHJ) Post Commissioning Activities 50 From the main menu.8 Procedure Page 26 of 34 Date: 9/4/2014 Title 2. click on the Snapshot button and save a current snapshot of the BTS (Current Data Only option is OK). 8 Procedure Page 27 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP . under Commissioning LNCEL parameters.Type of Guidelines -Number Revision . If they are still zero call OSS support numbers. Proceed to the NSN TD-LTE ATP MOP and perform Site Acceptance testing using TAPAS. 53 Important: ATP will fail if previous step is not performed (eCSFB Parameter push and verification) After ATP completion and before leaving site lock all 3 sectors by changing Administrative State = Locked.2 [Ref: Appendix B] 55 Enable DRX by following step 16 and selecting true ENB final state (before leaving site) should be: OAM Connected /Integrated /TRS Commissioned 56 Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. 54 For more detail see MOP titled Nokia_ENB_Lock_Unlock_MOP – Section 1.BBU (FSIH) & RRU (FZHJ) Verify if eCSFB push is successful by confirming that values for following parameter under each LNCEL object are non zero: 52 Note: If above parameters are zero wait for 10 minutes and re-check.8 Page 27 (34) .Number Document Method of D512241255 0. Type of Guidelines -Number Revision . POST C&I CHECKLIST AND SCOP UPLOAD Use this checklist to verify C&I was successfully completed. please contact your market project manager. If you need an account set-up. ART is a program that is utilized by Sprint to collect closeout documents and a subscription will be required to access the system. as well as the Integration and commissioning the EnB enginner will collect closeout pictures and upload them to ART.5 Commissioning & Integration MOP . Task Status Step Complete [C] Step Description Not Complete [NC] 1 Prior to leaving the Site the ENB engineer will verify the following items have been comlpleted and the status of each the status of all the deliverables has been forwarded to the market PM.8 Procedure Page 28 of 34 Date: 9/4/2014 Title 2.8 Page 28 (34) . Table 3: Post checks installation steps. 2 Upon completion of the Installtion of the NSN components.Number Document Method of D512241255 0. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.BBU (FSIH) & RRU (FZHJ) 4. Link to ART: https://nvart.5 Commissioning & Integration MOP . Camera to have 8megapixel capability.com/ Art overview can be found in Appendix (#) Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.8 Procedure Page 29 of 34 Date: 9/4/2014 Title 2.Number Document Method of D512241255 0.BBU (FSIH) & RRU (FZHJ) Picture size will be a minimum of 1280 x 720.sprint.Type of Guidelines -Number Revision .8 Page 29 (34) . Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. compressed to a zip file and uploaded to the documents folder for that particular site.Number Document Method of D512241255 0.8 Procedure Page 30 of 34 Date: 9/4/2014 Title 2. It is expected tat the photos will be uploaded the same day that they taken. A notification e-mail will be sent to the CPO organization and the market PM.5 Commissioning & Integration MOP .8 Page 30 (34) .BBU (FSIH) & RRU (FZHJ) Description of Photos to be collected and uploaded to ART 3 Pictures will be labeled.Type of Guidelines -Number Revision . BBU (FSIH) & RRU (FZHJ) Open site and click documentation Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0.Number Document Method of D512241255 0.Type of Guidelines -Number Revision .8 Page 31 (34) .5 Commissioning & Integration MOP .8 Procedure Page 31 of 34 Date: 9/4/2014 Title 2. 5 Commissioning & Integration MOP .8 Procedure Page 32 of 34 Date: 9/4/2014 Title 2.Type of Guidelines -Number Revision .Number Document Method of D512241255 0.8 Page 32 (34) .BBU (FSIH) & RRU (FZHJ) Load pictures to C&I folder Choose following options when uploading pictures to Site folder 4 5 Upon leaving the site Call the Sprint NOC at 1-866-400-6040 and informed them you leaving the site. Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. pdf 7.8 Page 33 (34) .5 Commissioning & Integration MOP .xlsx 6.8 Procedure Page 33 of 34 Date: 9/4/2014 Title 2.Number Document Method of D512241255 0.Type of Guidelines -Number Revision . APPENDIX B: ENB LOCK UNLOCK PROCEDURE Nokia_ENB_Lock_Unl ock_MOP_ver2.BBU (FSIH) & RRU (FZHJ) 5. APPENDIX A: C&I TROUBLESHOOTING GUIDE Sprint_C&I_Troubles hooting_Guide_v2. APPENDIX C: TCP/IP SETTINGS Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. 8 Procedure Page 34 of 34 Date: 9/4/2014 Title 2.xlsx Copyright © Nokia Solutions and Networks 2014 D512241255 SITE ENGINEERING 0. APPENDIX F: SITE MASTER SHEET (FOR RET ANGLES) SPRINT-MasterList-2 .Type of Guidelines -Number Revision .pptx 10.5 Commissioning & Integration MOP . APPENDIX D: FSIH PORT DIAGRAM 9.Number Document Method of D512241255 0.5GHz. APPENDIX E: ART OVERVIEW ART Template for OEM ICI CCFA_Draft_0 6.8 Page 34 (34) .BBU (FSIH) & RRU (FZHJ) 8.