2013-06-20 Health Care Sinks Document

TECHNICAL DATA Material thickness grade 18 gauge (1. This fixture is coated with SANIGUARD® product protection.HAND HYGIENE SINK HWS1414P-00 Z8000 Compliant Antimicrobial Hand Hygiene Sink. Integral 1 1/2” (DN 40) tailpiece is welded to the bottom of the basin. strainers and anti-splash fittings which are not allowed by the Z8000 guidelines.2mm) type 304 stainless steel. Franke CS .   Recommended for laminar flow.franke-commercial. LEED MR credit 4: Franke Commercial Systems ws-info. SANIGUARD® product protection is applied to all exposed surfaces of the sink. an in wall carrier is not required and the sink can be carried and installed by one person. Waste is left open and shaped to prevent the assembly of plugs. A wall hanger bracket is used to mount the sink to the wall. Silver ions are only released in the presence of bacteria-laden moisture and disrupt the metabolic and reproductive cycles of the micro-organisms. High back and side walls contain splashing and protect adjacent surfaces from contamination. molds and mildews.2 mm) Surface treatment Saniguard Bowl finish satin finished Gross weight 15 kg Type of waste kit integral tailpiece Splash back yes Undercoated no Waste hole position rear left Splash back height 8" (203 mm) Overflow no Certificates and approvals cUPC approval. Due to the strength and lightness of stainless steel.com www.com 2012-09-24. user temperature controlled deck mounted faucet. Left rear waste location to prevent water from splashing directly into the waste from both the faucet and during hand washing. 18 gauge (1. This treatment utilizes a silver ion technology to inhibit the growth of bacteria.ca@franke. 1-08 for Vitreous China Fixtures Valve Listings: • ANSI A117. • Optional thermostatic mixing valve (605XTMV) is available & must be ordered separately © 2012 AS America Inc.111 ICU Sink (fixture only) SINK: • Vitreous china • Permanent EverClean® surface inhibits the growth of stain & odor causing bacteria. SEE REVERSE FOR ROUGHING-IN DIMENSIONS Selectronic® FAUCET: • Hygienic hands-free operation • Rigid gooseneck spout with 5" reach • 1.No mix of air & water • Plain spout end .100 ICU Sink System with AC powered Selectronic ® Faucet ❏ 9118.1 • CSA B 125 • NSF 61/Section 9.19.ICU SINK SYSTEM WITH SELECTRONIC® ICU FAUCET WITH EVERCLEAN ® ICU SINK SYSTEM WITH SELECTRONIC ® ICU FAUCET ❏ 9118.150 ICU Sink System with DC (battery) powered Selectronic ® Faucet ❏ 9118. American Standard will not be liable for any splashing that occurs if faucets other than the American Standard ICU Faucets are used.5 gpm laminar flow restrictor in spout shank .150 System: Includes CR-P2 Lithium battery. Annex G DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on this ICU Sink.25% total lead content by weighted average Nominal Fixture Dimensions: 509 x 432 x 663mm (20" x 17" x 26-1/8") Fixture Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112. 4/12 .2-2008 / CSA B45.Nothing on the end of the spout to collect lime & debris Power Options: • Plug-In . 200.S. One transformer can run up to 15 faucets and/or flush valves in series.Approx. Battery Life . N99 Rev. flex hose with 3/8" compression connection • Lead Free: Faucet contains ≤ 0.000 cycles per month) • Fully enclosed. 50-60 Hz) with 6' long cord.100 System: Includes universal low voltage transformer (80-250 VAC. water resistant & hermetically sealed electronic controls • Vandal-resistant durable brass construction • Integral in-line strainer prevents clogging • Factory-installed 15" long S.000 cycles (4 years @ 4.1 • ANSI A112.9118. mold & mildew • Deep basin & sloped ledges minimize splashing • Sink drain is offset so that the water stream does not fall directly on the grid drain • Sink is designed with sealed overflow to eliminate an area for water to pool • Includes removable acrylic shroud (with mounting hardware) to allow access to the faucet electronics • Includes offset grid drain & P-Trap with SANIGUARD®** coating **SANIGUARD is a registered trademark of the Component Hardware Group.9118. • DC (Battery) . Inc.18. The Selectronic ICU Faucet was specifically designed to minimize splashing during operation. 36-1/2" (927mm) 32mm (1-1/4) DIA. (65mm) 8"(203mm) BETWEEN MOUNTING HOLES *FAUCET PERCH (53mm) 2-1/8" DIA. SMITH MFG. MODEL SQ-0-4437 FLOOR MOUNTED SINK SUPPORT FINISHED FLOOR WATTS CA-311 FLOOR MOUNTED URINAL CARRIER FINISHED FLOOR BASE MOUNT DETAIL 9/16" DIA. 14-3/4" (375mm) (133mm) 5-1/4" MOUNTING SURFACE 1/2" DIA. (14mm) 2-3/4" (70mm) 2-3/4" (70mm) 4" (102mm) © 2012 AS America Inc. 1-5/8" (41mm) 36-1/2" (927mm) RECOMMENDED CARRIERS: JAY R.ICU SINK SYSTEM WITH SELECTRONIC® ICU FAUCET WITH EVERCLEAN ® 4-3/4" (121mm) 20" (509mm) 4-3/4" (120mm) 17" (432mm) 5/8" (14mm) *FAUCET PERCH 2-1/2" DIA. CO. (13mm) 40-1/8" (1020mm) 26-1/8" (663mm) (243mm) 9-9/16" (127mm) 5" 2-1/2" DIA. 4" (102mm) N100 Rev. 125mm (4-7/8) 114mm (4-1/2) 36" (914mm) 413mm (16-1/4) FINISHED FLOOR 500mm (20") 8" (203mm) FINISHED WALL 81mm (3-3/16) MOUNTING STUDS 1524mm (60) 3/8" COMP. (65mm) 60mm (2-3/8) MAX. 4/12 . mesuré à une pression d’écoulement de 45 psi Corps de robinet : laiton résistant à la dézincification Brise-jet laminaire Électrovanne Sensibilité des capteurs : réglage automatique et permanent Durée d’écoulement : 0.HANSAMIX-S Electronic faucet.6 seconds) Adjustable mixed water temperature with lateral handle (fixed setting possible) Rapid installation system Two flexible connection hoses and dirt-collecting filters Non-return valves integrated into the faucet’s body Projection: 4 3/8” (111 mm) Solar cell and 6V Lithium DL 223A Approximate durability of battery: 5 years Resistant to 80°C temperature for thermal shock disinfection Débit : 6 l/min. at 45 psi hydraulic pressure Body: DR brass Laminar stream nozzle Solenoid valve Sensor sensitivity: permanently self-adjusting Water flow duration: 0.5-0. solar with battery support Sensory operation (infrared) Robinet électronique avec cellule photovoltaïque et pile en support Déclenchement optoélectronique (infrarouge) MEDIC Model Modèle Finish Fini 5077 2220 Chrome Chromé Specifications: Spécifications : Flow rate: 6 l/min.4 seconds (pre-set: 1.5-4 secondes (préréglage : 1.6 secondes) Température d’eau mitigée réglable avec manette latérale (réglage fixe possible) Kit de fixation express Deux flexibles de raccordement armés et filtres anti-impuretés Clapets anti-retour intégrés dans le corps du robinet Saillie : 4 3/8 po (111 mm) Cellule photovoltaïque et pile 6V Lithium DL 223A Durée de vie approximative de la pile : 5 ans Résistant à une température de 80°C pour désinfection par choc thermique HANSA Optional accessories / Accessoires optionnels Plate / Plaque 6” Model / Modèle 906215 Plate / Plaque 8” Model / Modèle AL800 Approbation HANSAMEDIC 21 . .1 Kg) P4008 Model Shown 2" SLIDING ADJUSTMENT INLET FOR 1-1/2 (38) DIA.. 4-3/16 (107) 2-1/2 (64) 9 (228) Dimensions shown in inches (mm) are for reference only and are subject to change... deep wall flange and cleanout............. TUBE 3 (76) DIA 1-1/2 (38) DIA......4 GPM (36 L/Min) Shipping Weight ........ 2...............P4008 P-Trap Adjustable 1-1/2" Plated P4008 Specification: Commercial grade cast brass 1-1/2" (38 mm) adjustable p-trap......................wattscanada........ Assembly includes a resilient polished chrome plated finish.ca Ph Ph 888-208-8927 888-208-8927 Fax Fax 888-479-2887 888-479-2887 Revision Revision A A 08/27/04 08/27/04 www... 9.. Ordering Code: 282 P4008 www.wattscanada...... Minimum Flow Rate ........ca ..5 Lbs (1.. 5mm (3/8") OD x 305mm (12") long flexible braided stainless steel riser.5mm (3/8") OD x 305mm (12") long flexible riser tube.) 47T2712SD Engineer/Architect Approval Model Specified: Approval: Date: Note: Measurements may vary ± 6mm (0. chrome plated finish. lockshield.5mm (3/8") OD x 305mm (12") long flexible riser tube. 12. stainless steel wall flange. stainless steel wall flange. 3/8” IPS brass inlet supply nipple. screwdriver slot. angle lavatory supplies. lockshield. 3/8" IPS brass inlet supply nipple. Note: Use this page front and back as a product submittal sheet.specselect. 8. angle lavatory supplies. see Back Page. chrome plated finish. 1/2" IPS inlet.com for finish options and product availability. (For stop valve only. Delta reserves the right (1) to make changes in specifications and materials. 12. stuffing box cartridge. stainless steel wall flange. stuffing box cartridge. stuffing box cartridge. 9. Dimensions are for reference only.Lavatory Supplies Specification: (example) 47T2312 o 47T2312 47T2312SD Pair of heavy pattern. stainless steel wall flange.18.C. but less riser) 47T2512SD Specification: (example) o 47T2622 Pair of heavy pattern. stuffing box cartridge.3 B . 47T2512 lockshield. 060853A) o 47T2512SD-LR (Same as 47T2512SD. stainless steel wall flange. 47T2622 (No inlet supply nipple) o 47T2622SD Pair of heavy pattern. stainless steel wall flange.specselect. chrome plated finish. and (2) to change or discontinue models. angle lavatory supplies.7mm (1/2") OD x 305mm (12") long flexible riser. DSP–47T Rev. 9. 9. 3/8" IPS brass inlet supply nipple. screwdriver slot. o 47T2512SD Pair of heavy pattern. angle lavatory supplies. 1/2" IPS inlet. chrome plated finish. 1/2" nominal (5/8" OD) copper compression inlet. (No inlet supply nipple) Specification: (example) o 47T2712SD Pair of heavy pattern. chrome plated finish. o 47T2312SD Pair of heavy pattern. oval handle. See current full-line price book or www.1 (Contact Delta Representative for State and/or Local Approvals. 3/8" IPS brass inlet supply nipple. angle lavatory supplies. screwdriver slot. angle lavatory supplies. both without notice or obligation. (No inlet supply nipple) 47T2622SD ® Approvals: • CSA certified • Complies to ASME A112. chrome plated finish. stuffing box cartridge.5mm (3/8") OD x 305mm (12") long flexible braided stainless steel riser. (For stop valve only. see Back Page. stainless steel wall flange.25") Refer to www. chrome plated finish. oval handle.7mm (1/2") OD x 305mm (12") long flexible riser. lockshield. oval handle. 9.5mm (3/8") OD x 305mm (12") long flexible riser tube. stuffing box cartridge. 060853A) Specification: (example) o 47T2512 Pair of heavy pattern. B DSP–47T Page Rev. stuffing box cartridge. 9.com for individual models. screwdriver slot. angle lavatory supplies. 1/2" IPS inlet. B DSP–47T Rev. 9.C. Dimensions are for reference only.4 Rev. . 3/8" IPS brass inlet supply nipple. stuffing box cartridge. angle closet supply. angle closet supply. screwdriver slot.specselect. chrome plated finish. stainless steel wall flange. and (2) to change or discontinue models. chrome plated finish.7mm (1/2") OD x 305mm (12") long flexible riser. oval handle. stainless steel wall flange. stuffing box cartridge. (No inlet supply nipple) 47T1326SD ® Approvals: • CSA certified • Complies to ASME A112. stainless steel wall flange. Delta reserves the right (1) to make changes in specifications and materials. B Note: Use this page front and back as a product submittal sheet.specselect. lockshield. screwdriver slot. 12. 47T1316 o 47T1316SD Heavy pattern. lockshield.18.) Engineer/Architect Approval Model Specified: Approval: Date: Note: Measurements may vary ± 6mm (0. 9. stuffing box cartridge. See current full-line price book or www.1 (Contact Delta Representative for State and/or Local Approvals. o 060853A One only angle stop valve for 47T1316SD and 47T2312SD complete with 3/8" compression nut and sleeve. 3/8" IPS brass inlet supply nipple.5mm (3/8") OD x 305mm (12") long flexible riser. Page DSP–47T 8.com for individual models.com for finish options and product availability.Closet Supplies Specification: (example) o 47T1316 Heavy pattern. both without notice or obligation. chrome plated finish.5mm (3/8") OD x 305mm (12") long flexible riser. angle closet supply.25") Refer to www. 47T1316SD Specification: (example) o 47T1326SD Heavy pattern. universal steel hanger support plate.321 CANADA 0403 (Dimension) Denotes Millimeters 272 . universal steel hanger support plate and bottom bearing plate.CA-311. L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www. per add inch (single) Wall Thickness over 12". and plated hardware. Single Floor to Ceiling Adaptor. CANADA CANADA: 5435 North Service Road. and plated hardware. Burlington. 321 Urinal Carriers Tag: CA-311 SPECIFICATION: Watts Drainage Products CA-311 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet. CA-321 SPECIFICATION: Watts Drainage Products CA-321 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet. See your WATTS Drainage representative for any clarification. Engineer Representative WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to products previously or subsequently sold.wattsdrainage. CA-321 ASSEMBLY TO SUIT WHEN USED WITH FIXTURE LOWER PLATE ROUGH-IN FIXTURE HANGER SUPPORTING STUDS BEARING STUDS NOT ATTACHED TO FIXTURE -M51 -M52 -M53 -M59 -M60 -M61 -M62 Description Wall Thickness over 5". Single Valve Supporting Bar.O. Single 42" (1067) LOWER BEARING PLATE 20-1/2" (521) RECTANGULAR STEEL STRUCTURAL UPRIGHTS NOTE: FOOT SUPPORTS SHOULD BE SECURELY ANCHORED TO FLOOR WITH 1/2" BOLTS AND ANCHORS BY OTHERS. Single Flush Valve Piping Support. Single Valve Supporting Plate. CA-311-M51 Options (Select One or More) Suffix FIXTURE HANGER SUPPORT PLATE CA-311 ASSEMBLY WHEN USED WITHOUT LOWER PLATE. Order Code: 1" x 2" (25 x 51) BACK OF SUPPORT BRACKET FRONT OF SUPPORTING PLATE CA-311OR CA-321- Ex. Job Name Contractor Job Location Contractor's P. No.ca © Watts Drainage 2003 ES-WD-CA-311. ON. per inch (Back to Back) Vandal Proof Trim. Dimensions are subject to manufacturing tolerances. HEAVY DUTY STEEL FOOT SUPPORTS 3-1/4" (83) 4-1/2" (114) NOTE: Recommended for support of wall-hung urinals independent of wall. TO AVOID DAMAGE AND POSSIBLE INJURY HANDLE WITH CARE! NOTE: Pictures may not exactly define contour of china and components.. review the recommended tools and materials list. CO. please read these instructions carefully before you begin. (14mm) 36" (914mm) 2-3/4" (70mm) 2-3/4" (70mm) FINISHED FLOOR BASE MOUNT DETAIL 4" (102mm) S A V E 8"(203mm) BETWEEN MOUNTING HOLES *FAUCET PERCH F O R *FAUCET PERCH 2-1/2" DIA.INSTALLATION INSTRUCTIONS ICU Sink System Models: 9118. ! CAUTION: PRODUCT IS FRAGILE. carefully unpack and examine your new plumbing fixture. The Selectronic ICU Faucet was specifically designed to minimize splashing during operation. Also. (65mm) RECOMMENDED CARRIER JAY-R 4" (102mm) *DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on this ICU Sink. 9118.. I n c . To help insure that the installation process will proceed smoothly.150 Introduction: Thank you for selecting our products. I n c . B .111. SQ-0-4437 FLOOR MOUNTED SINK SUPPORT Pro d u c t n a m e s l i s te d h e re i n a re t r a d e m a r k s o f AS A m e r i c a . (13mm) 40-1/8" (1020mm) 26-1/8" (663mm) FINISHED FLOOR FINISHED FLOOR 36-1/2" (927mm) 9/16" DIA. © A S A m e r i c a . Recommended Tools & Materials Tape Measure Adjustable Wrench Plumbers' Putty or Caulking Pipe Wrench U S E Torch Hacksaw Tubing Cutter Channel Lock Pliers Rough-In Dimensions Drill 4-3/4" (121mm) Phillips Screwdriver Regular Screwdriver 20" (509mm) 4-3/4" (120mm) 8" (203mm) FINISHED WALL MOUNTING STUDS 17" (432mm) 5/8" (14mm) 1-5/8" (41mm) F U T U R E Pencil Level 36-1/2" (927mm) 2-1/2" DIA. American Standard will not be liable for any splashing that occurs if faucets other than the American Standard ICU Faucets are used.100 & 9118. SMITH MFG. 2 012 1 7301793-100 Rev.products which have been the benchmarks of fine quality for years. (65mm) 14-3/4" (375mm) 1/2" DIA. if rigid supply risers are used. B 2 3 7301793-100 Rev. Insert WIRES (1). See illustration below. 4. Install the ELECTRONICS HANGER BRACKET onto remaining HANGER STUD. Place ELECTRONICS BOX onto MOUNTING PLATE. Thread DRAIN ELL onto GRID DRAIN. HANGER STUD 3. Use tubing cutter to cut TAILPIECE. 2 GRID DRAIN NOTE: Installation with ELECTRONIC BOX only is for cold or tempered water. B . Install NYLOCK NUT & WASHER but do not tighten fully. Connect OFFSET TAILPIECE to “P” TRAP. STAR WASHER (5) and LOCKNUT (6) onto threads of SPOUT SHANK (3) from underside of mounting surface. #(M965119) 1. Tighten with adjustable wrench to make a water tight connection. Attach with SCREWS provided. Align BOX with mounting holes. ELECTRONICS HANGER BRACKET SQ-0-4437 FLOOR MOUNTED SINK SUPPORT FINISHED WALL MOUNTING STUDS INSTALL ELECTRONICS HANGER BRACKET 4 5 1-5/8" (41mm) 36-1/2" (927mm) 6 8" (203mm) 4" (102mm) 4 3 2 3/8" (10mm) SUPPLIES NYLOCK NUT AND WASHER 5 1 6 18" (457mm) *1-1/4" (32mm) OR 1-1/2" (38mm) WASTE OUTLET FINISHED FLOOR 3 6 1. ELECTRONIC BOX 1-1/4" or 1-1/2" OD WASTE OUTLET GRID DRAIN 3. Do not over tighten. Apply plumber’s putty to the underside of flange. it is recommended that straight stops with flex supply tubes be used. TAILPIECE 1. Replace NYLOCK NUT & WASHER. Connect SUPPLY NUT (1) from SPOUT assembly to nipple on top of ENCLOSURE (2). TAILPIECE may have to be cut to fit installation. Align FAUCET and tighten LOCKNUT (6). 2. Assemble "C" WASHER (4). 1 MOUNT ELECTRONICS BOX 4 8 FRICTION GASKET 3 DRAIN ELL 3. From the underside of SINK install RUBBER GASKET (flat side up) and FRICTION GASKET onto GRID DRAIN threads. *CHECK LOCAL CODES 3 7 COMPLETE WASTE OUTLET CONNECTION INSTALL GRID DRAIN AND OFFSET TAILPIECE 1-1/4" OD 2. As an alternative. tighten and align as shown. Hang MOUNTING PLATE with ELECTRICAL BOX on HANGER BRACKET. Rough-in 3/8" supplies and waste outlet connections. Install “P” TRAP. chinaware could become damaged. Use optional MIXING VALVE with ELECTRONIC BOX when Hot and Cold supplies are roughed-in. 2. Remove COVER from ELECTRONICS BOX. 2. 1. Apply sealent to threads of OFFSET TAILPIECE and thread into DRAIN ELL. it is suggested to use angle stops in place of the straight stops. ELECTRONIC BOX SCREWS PLUMBER’S PUTTY APPLY SEALANT RUBBER GASKET 1 MOUNTING PLATE 2 APPLY SEALANT TO THREADS OFFSET TAILPIECE MIXING VALVE 7301793-100 Rev. Hold SINK in place and temporarily install NYLOCK NUT & WASHER on one of the HANGER STUDS to retain SINK. CONNECT SPOUT HOSE TO ENCLOSURE 1. Apply sealent to threads of GRID DRAIN. NOTE: For more detailed information. tighten both ends. 4 INSTALL FAUCET 5 INSTALL ICU SINK 1. COLD WATER OR TEMPERED WATER (3/8" SUPPLY) ELECTRONIC BOX MIXING VALVE HOT COLD P-TRAP DRAIN ELL 1. FLEX HOSE (2) and SPOUT SHANK (3) through center hole of mounting surface.1 2 ROUGH-IN SUPPLIES AND WASTE OUTLET 1. see the installation instructions supplied with the ICU FAUCET. NOTE: For ease of installation and accessibility. Mount SINK onto the two HANGER STUDS. Install GRID DRAIN into drain outlet. Remove NYLOCK NUT & WASHER from first HANGER STUD and install other end of ELECTRONICS HANGER BRACKET. Install FIBER SEAL WASHER (4) on MIXING VALVE NIPPLE (3).Turn on water supplies and check for leaks. WIRE HANGER is positioned behind ELECTRONIC BOX and in front of DRAIN. 3 I n s t a l l a t i o n I n s t ru c t i o n s NOTE: For complete detailed installation and operating instructions see installations instructions supplied with mixing valve.com For Parts. Check FAUCET operation. TION DETEC ZONE MODEL NUMBERS 6055. Use adjustable wrench to tighten connection. loop as to avoid kinking.amstd. Align BOX with mounting holes. Service. Important: If FLEXIBLE SUPPLY (3) is too long. No. No.us.111 ICU Sink Certified to comply with ASME A112. Turn off Hot and Cold water supplies before beginning.1M Product No. installer must purchase parts separately.'s & Options 1 Specifications 2 How to Install 2-3 Electrical Hook-up 4-6 Maintenance 7-8 FAQ.amstd. No. Do not over tighten.com or U. Tighten to make a water tight connection. Replace COVER and tighten securely. uncover the SENSOR (1) and fully open the water supply valve. To learn more about American Standard Faucets visit our website at: www.S. 3. 1" additional and re-attach. Warranty or other Assistance. To learn more about American Standard Faucets visit our website at: www.americanstandard.193 6056. ELECTRICAL HOOK-UP AND INSTALLATION No. customer's e-mail us at: [email protected] ICU Sink Certified to comply with ASME A112.s 9 Replacement Parts 10 ELECTRONIC BOX © 2011 American Standard M 9 6 5 119 HOT NOTE TO INSTALLER: Please give this manual to the customer after installation. 6.1M © 2005 American Standard Specifications 1 Installation 2 Adjust Temperature 3 Service 3 Replacement Parts 4 2. loop to avoid kinking. M965119 SELECTRONIC™ Proximity ICU Faucet 6055 / 6056 ICU Faucet shown Installed on American Standard 9118. Place MIXING VALVE BOX onto MOUNTING PLATE. steady stream. 1 2 4 3. When the water flows as a solid. Attach with SCREWS provided.com For Parts.193 Product No. please call 1-800-442-1902 (In Canada: 1-800-387-0369) (In (InToronto Toronto Area Area only: only: 1-905-306-1093) 1-905-3061093) 7301793-100 Rev. Insert FIBER WASHER (4) into SUPPLY NUT (1) on ENCLOSURE (2). 2. EYEBOLT for SINK APRON. 5. Remove THUMB NUT from EYEBOLT. 1. Faucet supplies measure 20" from the bottom of the ENCLOSURE (3) base. Warranty or other Assistance. 4 2 To learn more about American Standard Faucets visit our website at: www.18. Connections on MIXER supplies are 3/8" compression. M968808 INSTALL WIRE HANGER Note: If additional supply length is required. 1. Place WIRE end in right SIDE HOLE near DRAIN. NOTE TO INSTALLER: Please give this manual to the customer after installation.us. 4. M965119 I n s t a l l a t i o n I n s t ru c t i o n s 9 SELECTRONIC™ Proximity ICU Faucet 14 TEST INSTALLED FAUCET TO ENSURE A LAMINAR WATER FLOW the air must be slowly purged from the spout. Important: If SUPPLY HOSES (1. Hold MIXING VALVE (1) in place with one hand and with your other hand thread SWIVEL NUT (2) onto MIXING VALVE NIPPLE (3). No.18. Warranty or other Assistance. 2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to FLEXIBLE SUPPLY HOSE (3). smooth. M965119 I n s t a l l a t i o n I n s t ru c t i o n s For complete detailed installation and operating instructions see installations instructions supplied with ICU FAUCET. 4. cover the SENSOR (1) while slowly opening the water supply valves. If additional supply length is required.com or U.'s & Options 1 Specifications 2 How to Install 2-3 Electrical Hook-up 4-6 Maintenance 7-8 FAQ. Use adjustable wrench to tighten connections. Place WIRE end in left SIDE HOLE. 2. please call 1-800-442-1902 (In Canada: 1-800-387-0369) (In Toronto Area only: 1-905-3061093) 2 15 2. M965119. Connect left supply to Hot and right supply to Cold wall supply. Service. To do so.s 9 Replacement Parts 10 © 2011 American Standard M 9 6 5 119 NOTE TO INSTALLER: Please give this manual to the customer after installation. M968808 1 SELECTRONIC™ Thermostatic Mixing Valve WIRE 605XTMV 12 WIRE HANGER CONNECT MIXING VALVE TO WATER SUPPLIES 1. 2) are too long.13 CONNECT WATER SUPPLY TO ENCLOSURE AND TO COLD OR TEMPERED WALL SUPPLY 1. Use two wrenches to tighten if necessary.com For Parts. No.193 1 6055 / 6056 ICU Faucet shown Installed on American Standard 9118. Connect FLEXIBLE SUPPLY (3) directly to wall supply. Connect FLEXIBLE SUPPLIES directly to wall supplies. B MIXING VALVE 1 4 COLD 2 EYEBOLT WIRE HANGER REMOVE THUMB NUT FROM EYE BOLT 5 7301793-100 Rev. Connection on FLEXIBLE SUPPLY (3) is 3/8" compression. EYEBOLT 3. customer's e-mail us at: faucetsupport@americanstandard. remove WIRE and spread ends approx. Use an adjustable wrench to tighten SWIVEL NUT (2). ELECTRONIC BOX 3 COLD WATER OR TEMPERED WALL SUPPLY 3 Note: FLEXIBLE SUPPLY (3) measures 20" from the bottom of the ENCLOSURE (1) base. if adjustment is required refer to the installation instructions shown at right supplied with the ICU FAUCET. Install EYEBOLT onto WIRE HANGER if not installed. 10 CHECK ALL ELECTRICAL AND PLUMBING CONNECTIONS INSTALL AND CONNECT MIXING VALVE (MIXING VALVE IS OPTIONAL) ADJUSTABLE WRENCH 1.193 6056.S. Certified to comply with ASME A112.1M MODEL NUMBERS 6055. B .18. Remove COVER from MIXING VALVE. Do not over tighten. installer must purchase parts separately.S.com or U. Tighten any connections if necessary. M968808 WIRE NOTE: If not enough tension. please call 1-800-442-1902 (In Canada: 1-800-387-0369) (In Toronto Area only: 1-905-3061093) 11 3. Service. customer's e-mail us at: faucetsupport@amstd. Apply the two APRON BRACKETS to the finished wall parallel to the pencil marks as shown in the illustration below. 2. 9118. Clean the wall where the APRON BRACKETS supplied with SINK are to be applied.0070A Bracket Assembly THUMB NUT 7381259-401. 1. Hold APRON up against SINK and flush against finished wall.16 INSTALL SINK APRON Repair Parts 3.111. APRON APRON 7381266-200.0200A ICU Sink Shroud Kit EYEBOLT IMPORTANT: SAVE ALL INSTALLATION INSTRUCTIONS FOR FUTURE USE 7301793-100 Rev. Remove the APRON. Install SCREWS and tighten. Finger tight only. Apply the two APRON BRACKETS to the finished wall parallel to the pencil marks as shown and aligned with the mounting holes. See illustration below. Retain APRON with THUMB NUT. Position APRON under SINK and against finished wall alinging EYEBOLT with hole in APRON. B 6 7 7301793-100 Rev.150 OPTIONAL MOUNTING. 7381242-0500A P-Trap Assembly 6. (SCREWS AND ANCHORS NOT SUPPLIED) Use Brackets to mark pilot holes on wall. Peel off the protective strip from the back of the APRON BRACKETS. Drill holes for ANCHORS. Clean off the pencil marks from wall. B . Mark a line with a pencil on the wall about 6" long as shown on both sides of the APRON.. 4. ICU Sink System Models: 9118.100 & 9118. SINK PROTECTIVE STRIP 6" (152mm) CLEAN WALL PENCIL MARK 1/2" (13mm) APRON APRON 7381243-251. Peel off the protective strip from the back of the APRON BRACKETS.0020A Offset Drain 5. de R.O.com In Canada: AS Canada. Since local building codes vary considerably. This limited warranty does not cover any liability for consequential or incidental damages. if it has been subjected to faulty maintenance. In the United States: American Standard Brands P. ONE YEAR LIMITED WARRANTY If inspection of this AS America. (“American Standard”) plumbing product. TILES. all of which are expressly excluded from this limited warranty. Mexico Toll Free: 01-800-839-1200 www. This limited warranty does not apply to local building code compliance.americanstandard. You may have other statutory rights that vary from state to state or from province to province. so this exclusion may not apply to you. accident or other damages.mx THIS WARRANTY IS NOT TRANSFERABLE FROM ORIGINAL CONSUMER PURCHASER.com. ETC. the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation. abuse. American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or installation. INC. ULC 5900 Avebury Rd. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties. exchange the product for a similar model.L. de C. Ontario Canada L5R 3M3 Toll Free: (800) 387-0369 www. American Standard will not be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product. confirms that it is defective in materials or workmanship.americanstandard.ca In Mexico: American Standard B&K Mexico S.V. 7301793-100 Rev. Santa Clara Ecatepec 55540 Edo. B 8 . MARBLE. warranty information may also be obtained by calling the following toll free number: (800) 442-1902 www. or if it has been modified in a manner inconsistent with the product as shipped by American Standard. or the extension beyond the duration of this limited warranty of any implied limited warranties. In the event of a limited warranty claim. INCLUDING BUT NOT LIMITED TO. misuse.americanstandard. at its option. Box 6820 Piscataway. including those of merchantability or fitness for an intended purpose. if it was not installed in accordance with American Standard's instructions. in which case this limited warranty does not affect such statutory rights. proof of purchase will be required—save sales receipt. Mississauga. Via Morelos #330 Col. all of which are hereby expressly disclaimed. within one year after its initial purchase. This limited warranty is void if the product has been moved from its initial place of installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION MATERIALS. Inc.) This limited warranty gives you specific legal rights. New Jersey 08855 Attention: Director of Customer Care For residents of the United States.AS AMERICA. This limited warranty applies only to the original purchaser and installation of these products. American Standard will repair or. com Telephone 1-866-687-7465 Fax 1-800-361-8408 61562 0311 215 . Midland. This treatment utilizes a silver ion technology to inhibit the growth of bacteria.5" tailpiece Quote #: 3” [8 cm] 4 1/2” [11 cm] Kindred Commercial Kindred Commercial 10” [25cm] Faucet Model #: Drillings Required: Notes: 14” [36 cm] Franke Kindred Canada Limited 1000 Franke Kindred Road. This fixture is coated with SANIGUARD® product protection. SANIGUARD® product protection is applied to all exposed surfaces of the sink. Silver ions are only released in the presence of bacteria-laden moisture and disrupt the metabolic and reproductive cycles of the micro-organisms. Ontario.com • SANIGUARD® product protection is designed to protect the product itself and will not protect the user or others from food-borne illness or disease. Compartment Size: 14" x 20" x 10" (35cm x 51cm x 25cm) Overall Size: 18 3/4" x 21" x 37" (48cm x 53cm x 94cm) Backsplash: 26 1/2" (67cm) Notes: • Separate sink carrier is not required • Electronic specifications. molds and mildews. reference www. Waste location left rear.HWS1420P-00 Wash Basins & Troughs Specification: 18 gauge. Polished to a #4 satin finish. Always follow proper hygienic and cleaning procedures when using this product.com email info@kindred-sinkware. Canada L4R 4K9 web www. Fixture bowl is constructed with radius coved corners. type 304. 21” [53cm] 18 3/4” [48cm] PROJECT INFORMATION 26 1/2” [67cm] Printed in Canada Printed in Canada Project Name: 37” [94cm] Item Reference: Location: Integrally welded 1.kindred-commercial. 18-10 stainless steel medical hand wash basin.kindred-commercial. Integral side splashes help prevent splashing and contamination of nearby surfaces. Canada 1-888-279-7841 rjw.HAND HYGIENE SINK MODEL IC07DM Complies with: CSA Z8000 Standard CHICA Positioning Statement Material Dimensions • DuPont™ Corian® • Non-porous • Renewable • Easy to Clean with hospital approved cleaners and disinfectants Manufacturer: RJW Enterprises Inc.5”Wx11”Hx9”D Additional Features • Steel bracket for easy installation • Custom sizes available for backsplash • Wall mount faucet model also available • Easily removable plumbing hardware shroud .net Infection Control Features • Deep bowl sufficient to prevent recontamination • Drain is offset from faucet to minimize splashing • Thin rim sloped back to bowl • Faucet deck sloped back to bowl • Integrated coved backsplash • Solid underside • 9” Deep Bowl • Bowl & Backsplash [email protected]”Wx22”Hx18”D • 18” high backsplash • Plumbing Shroud 7. Specializing in Healthcare sinks since 1995 Ontario.