14228 Chassis 40 00NX56 MAN1XG NX56LA Manual de Servicio

SERVICE MANUALMODEL: 29M62S CHASSIS: NX56-LA CAUTION: 1、 Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SER VICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRI ELECTRIC C SHOCK DO NOT OPEN. The lighting flash with arrowhead symbol, with an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the person. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 2 IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Save these instructions for later use. Follow all Warnings and Instructions marked on the audio equipment. 1. Read Instructions- All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions- The safety and operating instructions should be retained for future reference. 3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions- All operating and use instructions should be followed. FOR YOUR PERSONAL SAFETY 1. 2. 3. 4. 5. 6. 7. 8. 9. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to qualified service personnel. Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to traffic or abuse. This may result in a shock or fire hazard. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet and refer servicing to qualified service personnel. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to qualified service personnel. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury to a child or an adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and should use a mounting kit approved by the manufacturer. 10.2. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 3 PROTECTION AND LOCATION OF YOUR SET 11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel. 12. Choose a place where light (artificial or sunlight) does not shine directly on the screen. 13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists. 14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to protect it from overheating. These openings must not be blocked or covered. Never cover the slots or openings with cloth or other material. Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc. Never place the set near or over a radiator or heat register. Never place the set in a built-in enclosure, unless proper ventilation is provided. PROTECTION AND LOCATION OF YOUR SET 15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrode, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD- IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS NEC-NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) 15.2. Note to CATV system installer : (Only for the television set with CATV reception) This reminder is provided to call the CATV system installer s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning and power-line surges. 17. 4 When going on a holiday : If your television set is to remain unused for a period of time. 22. 19.OPERATION OF YOUR SET 18. When replacement parts are required. ask the service technician to perform routine safety checks to determine that the television is in safe operating condition. This television set should be operated only from the type of power source indicated on the marking label. 25. particularly when being turned on or off. If the snapping or popping is continuous or frequent. or a distinct change in performance indicates a need for service. If you are unable to restore normal operation by following the detailed procedure in your operating instructions. when you go on a holiday. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the television set to normal operation. Upon completion of any service or repairs to the television set. unplug the set and consult your dealer or service technician. For television sets designed to operate from battery power. Whenever the television set is damaged or fails. 20. IF THE SET DOES NOT OPERATE PROPERLY 21. turn the television set off and unplug the television set from the wall outlet. Do not use attachments not recommended by the television set manufacturer as they may cause hazards. refer to the operating instructions. do not attempt any further adjustment. be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. FOR SERVICE AND MODIFICATION 24. unplug the set and have it checked by a professional service technician. or other hazards. Unplug the set and call your dealer or service technician. electric shock. 5 . It is normal for some TV sets to make occasional snapping or popping sounds. If the television set does not operate normally by following the operating instructions. 26. consult your television dealer or local power company. Unauthorized substitutions may result in fire. for instance. unplug this television set from the wall outlet and refer servicing to qualified service personnel. 23. If you are not sure of the type of power supply at your home. Page Version 1 of 7 1.TCL-Thomson Electronics R&D Center (Shen’Zhen Lab) Product Functional Specification Chassis Name Issued On Updated On NX56 2008-1-18 Serial No.0 . Page Version 2 of 7 1. the second one ”2” means the version of draft. e. 1. which is separated by one dot. Version Information: Version states by two Arabic Numbers.0 .TTE Corporation R&D Center (Shen’Zhen Lab) Disclosure Proprietary Information: These drawings and specifications are the property of TCL-Thomson Electronics and shall not be reproduced or copied or used as the basis for the manufacture or sale of apparatus or devices without the written permission of TCL-Thomson Electronics.2. Chassis Name Issued On Updated On NX-56 2008-1-18 Serial No. The first number “1” means the version of approved file.g. 0 03-BA41UAE-TH32 Checked by Released by: Revised by Checked by Released by: Revised by Checked by Released by: Revised by Checked by Released by: Chassis Name Issued On Updated On NX-56 2008-1-18 Serial No.TTE Corporation R&D Center (Shen’Zhen Lab) Revision History Model No.0 . Status Prepared by Date Comment 29A41 V1. Page Version 3 of 7 1. Size Sound -Audio Power Consumption -Surround Sound Chassis: NX-56 Version: 1.] -Tuning [Technology] -Tuning [Indication] -Frequency Bands -IF Frequency -TV Systems (Color+ Sound) -AV Systems Picture-Processing -SCAN -Wide Screen Switching -Comb filter -Picture Enhancement LTI / CTI Black Stretch Dynamic Skin Others -Picture Control [General] Brightness Sharpness Contrast Tint Color -Picture Control [Special] Smart Pictures * modes VM Color Temperature Others -Picture Noise Reduction Picture – Display -CRT Type Normal Flat Pure Flat Super Flat -Deflection system 1Fh 2Fh -Tube Technology Iron AK Black Matrix Others -CRT Deflection ( * Deg.0 Page 1 of 4 .9MHz PAL SECAM BG DK I NTSC PAL SECAM Standard X X X X X X 7 modes 3 modes X X X X 110 4:3 29' 5W+5W -CRT Magnetic Field -Screen Type -Screen Size / Vis.TTE Corporation R D Center (Shen’Zhen Lab) Model Item Master Data -Version -Customer ID -Destination -Brand -BOM NO.) NX-56-AP 29A41 1 EM EM 03-BA41UAE-TH32 255 PLL Digital and Bar Full Cable 38. -Chassis Reception -Tuning [Channels Amt. TTE Corporation R D Center (Shen’Zhen Lab) Model Item -Nicam -America Stereo (MTS.BTSC.0 Page 2 of 4 .MPS) -America SAP -Korea Stereo -Thai Bilingual -Super Woofer -AVL -Sound Control [General] Volume Mute -Sound Control [Special] Treble Bass Balance Equalizer Smart Sound * modes Others -Speakers Quantity User Interface -Menu Language -Features [General] AT Biological Clock Calendar Clock Channel Swap Channel Naming Child Lock Favorite Channel Game Hotel Mode High Sensitive Notebook On/Off Timer Preset Recall Rotation Sleep AVC -Features [Special] V-chip / CCD Teletext *Pages Others New Features Smart signal Voltage display 环境光检测 Easy search Tuning Features -Auto Channel Program -Auto/Manual Tuning -Auto/Manual Store -Fine Tuning -Factory Mode -Service Mode Cabinet -Cabinet Name NX-56-AP 29A41 X X X X X X 7 modes 2X1 English/Vietnam/Thai X X X X X X X X X X X X X X X X X Chassis: NX-56 Version: 1. Cb.0 Page 3 of 4 .5mm Final Equipment -Packing –Methods 2 Color Printing Carton Color -Documents and Manuals Instruction Book Screen Sticker Plastic Bag Warranty Card RC166 1+2 1(follow TV) X X Chassis: NX-56 Version: 1.Antenna in 75 Ohms (IEC Type) Connectors Front/Side -In Y/C+Cinch(CVBS+ Stereo) -In Y/C+Cinch (CVBS+ Mono) -In Cinch(CVBS+ Stereo) -In Cinch (CVBS+ Mono) -Out Headphone Mini-Jack 3.TTE Corporation R D Center (Shen’Zhen Lab) Model Item -Front Cabinet Color -Middle Cabinet Color -Rear Cabinet Color -Local Controls Front Mains Switch CH+ CH.Cr input -Super Woofer -Digital Audio Out -Loudspeakers -Control Busses -Feature Slot -ITV Smart Port .Y.VOL+ VOLTV/AV Menu Auto Search -Indicator RC Received LED Standby LED NX-56-AP 29A41 X X X X X X Remote Controller -Type -Batteries Connectors Rear -SCART Full w/o Y/C -SCART Full with Y/C -SCART Single (CVBS) -Component In (YPbPr) Cinch for 50Hz -In Y/C+Cinch(CVBS+ Stereo) -In Y/C+Cinch (CVBS+ Mono) -In Cinch(CVBS+ Stereo) -In Cinch (CVBS+ Mono) -Out Cinch(CVBS+ Stereo) -Out Cinch(CVBS+ Mono) .VOL+ VOLTV/AV Menu Auto Search -Local Controls Top CH+ CH. Warning Label Approbation Label Others -Languages DFU -Indication on BACKOVER Made-in in family sheet FCC/Elect Shock Caution Label CE/Elect Shock Caution Label Warning Label Others Approbation Miscellaneous -Mains Voltage -Mains Frequency -Type Mains Cord -Power Consumption TV in ON -Power Consumption TV in Standby NX-56-AP 29A41 IEC65 100-240V 50/60Hz 75W <3W Chassis: NX-56 Version: 1.0 Page 4 of 4 .TTE Corporation R D Center (Shen’Zhen Lab) Model Item Guarantee Doc. 0 . Page Version Page 1 of 17 4.TCL Multimedia Technology Holding CRT BU R&D Center NX56-AP&NX56B-AP Chassis Alignment Procedure Disclosure Proprietary Information: These drawings and specifications are the Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. which is separated by one dot. Version Information: Version states by two Arabic Numbers. Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No.TCL Multimedia Technology Holding CRT BU R&D Center property of TCL-Thomson Electronics and shall not be reproduced or copied or used as the basis for the manufacture or sale of apparatus or devices without the written permission of TCL-Thomson Electronics. the second one ”2” means the version of draft. The first number “1” means the version of approved file.2.0 . Page Version Page 2 of 17 4. 1.g. e. 0 1. Updated the description accord with the software changing. Page Version Page 3 of 17 4. Updated the description accord with the software changing. Prepared by 29A41/NX56 Checked by Released by Prepared by Luo MJ Guo Guangyuan Zhou Songming Luo MJ 2008-01-18 2008-01-23 2008-01-23 2008-07-04 Status Luo MJ Date 2008-01-18 Comment Ver0.1 03-BA41UAE-TH32（29A41/NX56） Ver1. Updated the B+ specs accord with 21” tube. 2. 2. All NX56-AP chassis Checked by Released by Prepared by All NX56-AP chassis Checked by Guo Guangyuan 2008-07-04 Released by Zhou Songming GUO HQ 2008-07-04 2009-02-09 14F1 21NCM86 29E64S All NX56-AP& NX56B-AP chassis Prepared by Checked by Released by Prepared by Checked by Released by Prepared by Checked by Released by Prepared by Checked by Released by Ver3.TCL Multimedia Technology Holding CRT BU R&D Center Revision History Model No. Ver2. Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. Updated the chassis name.0 . Updated the description accord with the software changing.0 Zhou Songming Luo MJ 2009-02-09 2009-04-24 Ver4. Updated the B+ specs accord with 25” tube. 2.0 1.0 1. “7”. the set will enter the P-Mode automatically. Press “1” to “8” and “FAV” key to select factory adjustment page. C) Move the cursor to “Contrast” item then press the “9”. 1.TCL Multimedia Technology Holding CRT BU R&D Center 1.3. 1. Press “MENU” key to close the factory menu or return to the previous menu or exit the P-Mode. This will be active only when the “FACTORY HOTKEY” had set to “ON (= 1)”. Exit the P-Mode Press the “RECALL” or “MENU” key on RC to exit the P-Mode. Press “DISPLAY” key to display software version. The “P” letter will appear on the left low corner of the screen when enter P-Mode. Press “►◄” or “VOL+ VOL-” key to adjust or select option. b) Another method Press the “RECALL” key on RC to enter P-mode directly. B) Press the “MENU” key on RC to show the “PICTURE” OSD menu. Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. The way to enter P-Mode a) Method one A) Switch on the TV set.1.2. Keys’ function on RC at the P-Mode Use the RC to navigate in P-Mode: Press “0” or “AT” key for screen voltage adjustment. “3”. Press “9” key to switch the I2C bus off/on. Note: All change in P-Mode will be saved in EEPROM automatically. Note: 1. Page Version Page 4 of 17 4. Press “▲▼” or “CH+ CH-”key to select option.0 . When the power on with “FACTORY HOTKEY” had set to “ON (= 1)”. “5” key continuously on RC within 3 seconds then enter P-Mode. Also the “FACTORY HOTKEY” will be set to “ON (= 1)”. Press “RECALL” key to enter or exit the P-Mode. 2. The adjustment page list an RC key function on P-Mode: RC key 0 1 2 3 4 5 6 7 8 FAV 9 DISPLAY MENU RECALL AT I2C Bus OFF/ON Software version Close menu or exit the P-Mode P-Mode hotkey Screen voltage adjustment with AKB Setup and option page select Item Screen voltage adjustment Vertical geometry Horizontal geometry White Balance Adjustment Description Adjust the VG2 voltage Vertical geometry page Horizontal geometry page White Balance page Setup and option page 4 Setup and option page 5 Setup and option page 6 Setup and option page 7 Setup and option page 8 Setup and option page 9 Press this key to enter or exit BUS OFF mode Display software version Close the factory menu or return to the previous menu or exit the P-Mode Enter or exit the P-Mode Adjust the VG2 voltage Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No.0 . Page Version Page 5 of 17 4.4.TCL Multimedia Technology Holding CRT BU R&D Center 1. 0 .TCL Multimedia Technology Holding CRT BU R&D Center 2. Flowchart of alignment procedure B+ adjustment Electrical properties checking for chassis White balance Adjustment NTSC geometry adjustment Aging Adjustment of focus voltage QC checking RF AGC adjustment Parameter setup Adjustment of screen voltaget PAL geometry adjustment Set shopping status 1) B+ Adjustment 2) RF AGC Adjustment 3) Screen & Focus adjustment 4) White balance adjustment 5) Producing parameter setup and option 6) Picture Geometry adjustment ( Vertical first) 7) Set Shopping status 8) QC Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. Page Version Page 6 of 17 4. 5V 125V+/-0. 4. Adjustment description Note: Alignment should be done after 3 minutes warm up of TV. Adjust VR801. Main voltage is at 220VAC.1. All relevant connectors and modules must be connected and inserted. Input Philips test pattern signal and standard mode.5V 125V+/-0.5V A59ERF181X03（44-25RFLN-HF1A） Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. it should as the value in below form B+ Voltage.5V 125V+/-0. 50Hz.0 . Connect a voltmeter to B+ (Cathode of D808 for NX56 chassis or cathode of D833 for NX56B chassis) and switch on the set. Page Version Page 7 of 17 4.TCL Multimedia Technology Holding CRT BU R&D Center 3.1 B+ Voltages 1.5V 108V+/-0. 2. 3. 5.1: The B+ value for vary tubes CRT type (Part Number) A68ERF185X013/M (44-29RFLN-HFCA) A51ERF135X90 (44-21RFLW-HF2A) A51ERS357X440(44-21RFLM-HF4A) CRTA68AGA20X99（44-29OFLW-TS4A） A59EEJ04X60（44-25OFLP-HF5A） B+ Voltage 125V+/-0.50Hz） 3. Table 3.（voltage range:110VAC~240VAC.5V 105V+/-0. Press “0” key on the RC and the screen will become a horizontal line. B. C. B.2 Method 2 A. Receive a grey scale signal with 70dBμV amplitude.0 . Connect the detector as shown below (Picture 3.2.3. Adjust the “AGCT” value until the hint display “AGC” just change between “0” and “1”. Enter P-Mode.8Vpp Collector of Q101 To CRO Picture 3. 5. 2.1 Method 1 A. Press “0” key again on the RC to exit the screen voltage adjustment mode. D. press “6” key on RC to select “AGCT”. like picture 3. Adjust the “SCREEN” VR of the FBT until the horizontal line can just be seen barely (minimum visible intensity). 3. Page Version Page 8 of 17 4. Receive a grey scale signal with 60dBμV amplitude.TCL Multimedia Technology Holding CRT BU R&D Center 3.3 NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Chassis Name Issued on Updated on Serial No. 4. press “6” key on RC to select “AGCT”.2 RF AGC alignment 3. Picture 3. 3. 1. Enter P-Mode. 2. C.2) to collector of Q101.2 3.3 Screen & Focus adjustment Note: Alignment below should be done after 15 minutes warm up of TV. Adjust AGCT item until the output of the detector becomes 0. Adjust the “FCOUS” VR of the FBT until the vertical line and horizontal line becomes clear. Input cross hatch pattern signal to RF input.2. Enter P-Mode. 5 for detailed PWL 8 Peak White Limiting Brightness of horizontal line when adjust G2 Brightness Contrast YUV white balance black level offset. “BLOG-Y” and “BLOB-Y” items are used for the YUV white balance black level offset setup. Adjust the value of “RC”.4 White Balance Adjustment 1. The “SubBRI” and “SubCON” items are used to assistant the white balance adjustment. Recommended value= “8” Don’t adjust. Table 3. 4. y=280. (11500 K). Use the color analyzer to measure the black side of the screen. Adjust the value of the “BLOR-Y”. Input a black and white pattern to RF input. When the TV white balance adjustment is done. connect a black and white pattern to YUV input terminal. Then measure the white side of the screen. Adjust the value of “RD”. Recommended value= “8” Adjust to right value accord with the tube.”GC” and “BC” to set the reading of the color analyzer to x=274. B. Sub-Brightness NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. (11500 K). Use the color analyzer to measure the black side of the screen. “BLOG-Y” and “BLOB-Y” to set the reading of the color analyzer to x=274.1: The White Balance adjustment OSD menu OSD menu RC GC BC RD GD BD BLOC Default Value 32 32 32 37 32 37 8 Description R cut-off setting(BLOR) G cut-off setting(BLOG) B cut-off setting(BLOB) R drive setting(WPR) G drive setting(WPG) B drive setting(WPB) Black level offset course(BLOC) Remark Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value accord with the tube.0 . use default value “32” for producing Same as user “Brightness” and “Contrast” adjust Adjust to right value accord with the difference tube and lot See section 3. 2. 3. y=280. “GD” and “BD” to set the reading of the color analyzer to x=274. Repeat step 3&4 until you can get the correct reading for both black and white sides. The “BLOR-Y”. Note: A. Page Version BriVSD SubBRI SubCON BLOR-Y BLOG-Y BLOB-Y BRTC Chassis Name Issued on Updated on 32 32 32 64 62 64 31 Page 9 of 17 4. It is the same function as the user OSD menu “Brightness” and “Contrast” items. You can adjust these items to get the expect intensity when adjusting the white balance. 5. y=280. press key “3” to select white balance adjustment menu. Enter P-Mode.TCL Multimedia Technology Holding CRT BU R&D Center 3.4. ) The 2nd gray scale Picture 3. Enter P-Mode. For NTSC signal. the “-50” will be replaced with “-60”. Apply NTSC signal to adjust these value for NTSC vertical geometry. Input eight steps gray signal. For NTSC signal. adjust “BRTC” until the secondary gray bar just to be seen.6.5. press key “1” to select vertical geometry adjustment.1 Vertical geometry adjustment 1.0 . For NTSC signal.6. 2.6.5 Sub brightness adjustment 1. 2. At dynamic state. the “-50” will be replaced with “-60”.6 Picture Geometry adjustment 3.) 3. (The OSD menu for this adjustment as below table 3.1. 4. Press key “3” to enter sub-brightness adjustment. Adjust the value of the corresponding item to make the vertical geometry of the pattern look good. Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. 3. the other items use the same data as PAL signal.TCL Multimedia Technology Holding CRT BU R&D Center 3. (like picture 3. Table 3. 2. Page Version Page 10 of 17 4. only the “VCEN-60” and “VSIZE-60” items need the adjustment.5 3.1: The vertical geometry adjustment OSD menu OSD menu VSLOPE-50 VCEN-50 VSIZE-50 VZOOM-50 VSC-50 VSCROLL-50 Default Value 32 32 32 25 32 32 Description Vertical slope(VS) Vertical shift (VSH) Vertical amplitude(VA) Vertical zoom(VX) S-correction(SC) Vertical Scroll（VCS） Remark Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Note: 1. Input a PAL crosshatch pattern signal to RF input. 7 Producing parameter setup and option Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. press key “2” to select horizontal geometry adjustment. If now the geometry of NTSC signal is look good.) 3. 2.6.0 . 3. For NTSC signal. 4.6. Input a PAL crosshatch pattern signal to RF input. please use the “AUTO OFFSET” (On page “2”) function to easy the geometry adjustment of NTSC signal. (The OSD menu for this adjustment as below table 3. 3. press “►” key to active the automatic offset function.6. For NTSC signal. only the “HCEN-60” and “HSIZE-60” items need the adjustment. press “►” key to active the automatic offset function. 3. When finished the PAL signal geometry adjustment. Then the geometry adjustment of NTSC signal will finish automated. When finished the PAL signal geometry adjustment. Then the geometry adjustment of NTSC signal will finish automated. please use the “AUTO OFFSET” (On page “2”) function to easy the geometry adjustment of NTSC signal. Apply NTSC signal to adjust these value for NTSC horizontal geometry.TCL Multimedia Technology Holding CRT BU R&D Center 3. For NTSC signal. the other items use the same data as PAL signal. If the geometry of NTSC signal is look good.2 Horizontal geometry adjustment 1. the “-50” will be replaced with “-60”. Table 3. On producing. press “2” key to enter page “2” to select “AUTO OFFSET” item. it not needed to adjust the geometry of NTSC signal any more. the “-50” will be replaced with “-60”.2. 2. you don’t need to adjust the geometry of NTSC signal any more. Adjust the value of the corresponding item to make the horizontal geometry of the pattern look good. On producing. Page Version Page 11 of 17 4. Enter P-Mode.2: The horizontal geometry adjustment OSD menu OSD menu HCEN-50 HSIZE-50 HPARA-50 HTRAP-50 HCNRT-50 HCNRB-50 HBOW-50 HPARALLEL AUTO OFFSET Default Value 32 32 32 32 32 32 32 32 0 Description Horizontal shift(HSH) EW width(EWW) EW parabola width(PW) EW trapezium(TC) EW upper corner parabola(UCP) EW lower corner parabola(LCP) Horizontal bow(HB) Horizontal parallelogram(HP) Automatic offset NTSC geometry Remark Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value See below description for detailed Note: 1. press “2” key to enter page “2” to select “AUTO OFFSET” item. 0 . See below table 3. The TV status after shopping status: A.7.1: Producing parameter setup and option page “4” OSD menu WARM UP STATUS SHOP INIT Default Value 0 0 Description Set aging mode Set the shopping status Crystal oscillator frequency adjustment Remark 0=Aging mode off 1=Aging mode on 0=>1= Set the shopping status Adjust this value to get the max color synchronization range. Page Version Page 12 of 17 4. Table 3.1 for detailed description. Set the shopping status When trigger the “SHOP INIT” item form “0” to “1”. the TV will be put on selling status. Don’t adjust. Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No.Set the corresponding item to require value.7. use default value for producing 0=”FACTORY HOTKEY” off 1=”FACTORY HOTKEY” on ON=On when power on POWER ON MODE EEPROM INIT POWER LOW POWER HIGH DEFAULT SND. press key “4” to select page “4”. and press “MENU” key the previous menu DCXO 2 FACTORY HOTKEY 1 Set factory hotkey BLACK BRI BRI CURVE CON CURVE COL CURVE VOL CURVE 40 >> >> >> >> Set the black background brightness while no signal Set the brightness curve Set the contrast curve Set the colour curve Set the volume curve Description: 1).TCL Multimedia Technology Holding CRT BU R&D Center 1. “FACTORY HOTKEY” had set to “OFF”. Enter P-Mode. SYS LAST 0 101 176 DK Set the power on mode EEPROM initial Set the “Voltage display” “LOW” and “HIGH” threshold Set the default sound system when auto store STB=Standby when power on LAST=Last power off status 0=>1=Active EEPROM initial Recommended value= “16” Recommended value= “168” Set the right value according to the sales area 0= Blue background for TV and AV while no signal BLUE BACK OPT 2 Set the Background option while no signal 1=Black background for TV and AV while no signal 2=Snowy background for TV and black background for AV while no signal Recommended value= “20” Press “►◄” or “VOL+ VOL-” key to enter a sub-menu to do the setup. Set the user picture and sound curve value A. Volume curve: OSD menu VOL0 VOL10 VOL30 VOL50 VOL80 VOL100 Default Value 0 38 65 71 77 83 Description Set the volume when user Volume=0 Set the volume when user Volume=10 Set the volume when user Volume=30 Set the volume when user Volume=50 Set the volume when user Volume=80 Set the volume when user Volume=100 Remark Use default value Set to 63 Set to 69 Set to 75 Set to 81 3).Balance=50. Select item “POWER HIGH.) C. E. Colour curve: OSD menu COL0 COL50 COL100 Default Value 0 32 63 Description Set the minimal colour when user Colour=0 Set the colour when user Color=50 Set the maximal colour when user Colour=0 Remark Set to 3 Use default value D. Page Version Page 13 of 17 4. Adjust the value until the hint display just change between “AC: NORMAL” and “AC: LOW”.0 . Adjust the value until the hint display just change between “AC: NORMAL” and “AC: HIGH”. Contrast curve: OSD menu CON0 CON50 CON100 Default Value 0 32 63 Description Set the minimal contrast when user Contrast=0 Set the contrast when user Contrast=50 Set the maximal contrast when user Contrast=0 Remark Set to 3 Use default value C. Colour=50.(Volume=30. Connect the main voltage at low threshold 95VAC/50Hz. Brightness curve: OSD menu BRI0 BRI50 BRI100 Default Value 0 32 63 Description Set the minimal brightness when user Brightness=0 Set the brightness when user Brightness=50 Set the maximal brightness when user Brightness=0 Remark Set to 3 Use default value B. D. F. B. Contrast=50. C. Connect the main voltage at high threshold 255VAC/50Hz. 2). Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. Select item “POWER LOW”.) D. Sound set normal. Set the value for “POWER LOW” and “POWER HIGH” A.TCL Multimedia Technology Holding CRT BU R&D Center B. White tone=Normal. (Brightness=50. Picture set to “Standard” status. TCL Multimedia Technology Holding CRT BU R&D Center 2. WBF WBR GET OFFSET ColdRC ColdGC ColdRD ColdGD WarmRC WarmGC WarmRD WarmGD Default Value 1 25 0 5 8 0 61 56 61 66 72 71 65 64 Description EHT tracking mode 4:3 mode vertical zoom 16:9 mode vertical zoom Wide blanking start Wide blanking end Get offset Cold color temperature R and G cut-off offset Cold color temperature R and G drive offset Warm temperature R and G cut-off offset Warm color temperature R and G drive offset Remark 0=EHT tracking only on vertical 1=EHT tracking on vertical and EW Don’t adjust. Enter P-Mode. press key “6” to select page “6”. See below table 3. When finished the PAL geometry adjustment. trigger the “GET OFFSET” from “0” to “1” to store the geometry offset datum between PAL and NTSC in EEPROM. 3. use default NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. RF AGC alignment” Don’t adjust. press key “5” to select page “5”. these geometry offset datum can use to easy the NTSC geometry adjustment. If now the geometry of NTSC signal is look good. On producing. use default See below description for detailed Recommended value= “61” Recommended value= “56” Recommended value= “61” Recommended value= “66” Recommended value= “72” Recommended value= “71” Recommended value= “65” Recommended value= “64” Description for AUTO OFFSET and GET OFFSET: The “GET OFFSET” can use to make the EEPROM copy by PE engineer.7. use default Don’t adjust. Page Version Page 14 of 17 4. See below table 3.7. use default Don’t adjust.2 for detailed.3: Producing parameter setup and option page “6” OSD menu AGCT AGC OIF Chassis Name Issued on Updated on Default Value 32 0 32 Description AGC take over point AGC take over point indicate IF demodulator offset Remark See section “3. Set the corresponding item to require value. use default Don’t adjust.3 for detailed description. it not needed to adjust the geometry of NTSC signal any more. Enter P-Mode.7.2: Producing parameter setup and option page “5” OSD menu Track. Table 3. Mode VX Normal VX Compr.2 for detailed description. Table 3.0 . trigger the “AUTO OFFSET” from “0” to “1”. Set the corresponding item to require value.7. When the PAL and NTSC geometry adjustment had finished. then the geometry adjustment of NTSC signal will finish automated. 7.90 1 3 IF frequency AGC speed Audio gain Select the IF frequency Don’t adjust. use default Don’t adjust. use default Don’t adjust.4 for detailed description. See below table 3.0 Remark 0=Disable 1= Enable 0=3 x 3 1=4 x 3 0=Disable 1=Enable . use default Adjust to right value accord with the tube.7. Recommended value= “12” 0=Disable 1= Enable 0=Stereo speaker 1=Mono speaker CL NTSCM NTSC443 ONE SPEAK 8 0 0 0 5. Enter P-Mode. use default Don’t adjust. See below table 3. Table 3. press key “8” to select page “8”. Set the corresponding item to require value.5 and table 3. Enter P-Mode. use default 4. Table 3.TCL Multimedia Technology Holding CRT BU R&D Center IF AGCS AGNE 38. Page Version Page 15 of 17 4. use default Don’t adjust. Set the corresponding item to require value.5: Producing parameter setup and option page “8”(For AP2 version) OSD menu HOTEL A2 THAI PIC PRESET AV ALIGMENT SHVS ENABLE YUV ENABLE NOCOMMAND ENABLE ARABIC* Chassis Name Issued on Updated on Default Value 0 1 1 1 1 1 0 1 NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Description Hotel mode enable Thailand dual language enable Picture preset enable Rear AV terminal align S-Video terminal enable YUV terminal enable No operation within 2 hours automatic standby enable Arabic enable Serial No.4: Producing parameter setup and option page “7” OSD menu EVG DFL XDT AKB NBL OSVE Default Value 0 0 0 1 1 0 Description Enable vertical guard(RGB blanking) Disable flash protection from deflection timer X-ray detection Black current stabilization Black current loop application Black current measuring lines in over scan(for vertical zoom setting <1) Set the cathode drive level RF NTSC M enable AV NTSC443 enable Mono speaker output setup (Note: this item is available on AP3 version) Remark 1= RGB blanking Don’t adjust. press key “7” to select page “7”. use default Don’t adjust.6 for detailed description.7.7.7. Page Version Page 16 of 17 4.7. press key “FAV” to select page “9”.6: Producing parameter setup and option page “8”(For AP3 version) OSD menu HOTEL A2 THAI HEALTH FLAT AC DISPLAY AV ALIGMENT AV2 ENABLE SHVS ENABLE YUV ENABLE NOCOMMAND ENABLE THAI* VIET* TUNER TYPE* Default Value 0 1 1 1 1 1 1 1 0 1 1 1 Description Hotel mode enable Thailand dual language enable Health platform TV enable AC voltage checking enable Rear AV terminal align AV2 input enable S-Video terminal enable YUV terminal enable No operation within 2 hours automatic standby enable Thai enable Vietnamese enable Select tuner type AV no signal within 10 minutes automatic standby AV output source follow 0=ALPS tuner 1=TCL tuner AV STANDB AVOUT FOLLOW 0 0 0=Disable 1=Enable 0=Follow TV 1=Follow source 0=Disable 1=Enable 0=3 x 3 1=4 x 3 0=Disable 1= Enable Remark *Note: When change the Language or the tuner type. Set the corresponding item to require NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Chassis Name Issued on Updated on Serial No. Enter P-Mode. 6.0 . you must AC restart the TV set to make it active.TCL Multimedia Technology Holding CRT BU R&D Center RUSSIAN* FRENCH* FARSI* TUNER TYPE* 1 1 1 1 Russian enable French enable Farsi enable Select tuner type AV no signal within 10 minutes automatic standby AV output source follow 0=ALPS tuner 1=TCL tuner AV STANDB AVOUT FOLLOW 0 0 0=Disable 1=Enable 0=Follow TV 1=Follow source Table 3. Page Version Page 17 of 17 4. press RC key "AT". Enter P-Mode.0 .7. 4. there will display 3.7 for detailed description.7: Producing parameter setup and option page “9” OSD menu BKS BSD Default Value 1 0 Description Black stretch enable Black Stretch depth Remark 0=Disable 1=Enable 0=15IRE 1=30IRE 0=12% AAS 0 Black area to switch off the black stretch 1=20% 2=6% 3=8% 0=1:1 RPA 1 Ratio of pre. Put the TV in AV source without input signal.8 Screen voltage (VG2) adjustment with AKB function 1. Adjust the "SCREEN" VR of the FBT until VG2 hint display (LOW/OK/HIGH) display "OK" stably.TCL Multimedia Technology Holding CRT BU R&D Center value.7 0=0% SOC 2 Soft clipping level above PWL 1=5% 2=10% 3=Soft clipping off 0=off COR 0 Video peaking active range 1= between 0 and 20 IRE 2= between 0 and 40 IRE 3= between 0 and 100 IRE 3. Table 3.7 4=1:0.5:1 2=2:1 0=1:1 RPO 1 Ratio of positive and negative peaks 1=1:1. 2. Chassis Name Issued on Updated on NX56-AP&NX56B-AP 2008-01-18 2009-04-24 Serial No. Press “MENU” return to P-Mode.and after shoot 1=1.7.3 3=1:1. See below table 3. IC601 TDA7266SA EEPROM IC001 UOC IC201 Pin 56 H.2008 B 33V +-14V 12V 9V Q501 Q503 Q505 AMP Bridge Rectifier DB801DB804 CRT ▽ Tuner TU101 Antenna Photo-Coupler IC803 R/G/B P201 IF AMP Q101 SAW Z2O1 Pin44-46 Pin14/15 VDA/B SCA/SDL P901 TV/AV/SV P202 KEY &IR001 SENSOR pin21 IC701 AN5832SA Aout -L/R IC702 74HC4053 Audio AMP.Driver AMP Q401 Q402 B+ 200V FBT T401 24V 6. IC301 STV8172A .OUT H.AMP.3V speakerX2 V.Chapter II 220VAC INPUT Block Diagram of NX56 Power Transistor Q801 2SK2996 IC801 NCP1337 Transformer T801 July5. the another one is for Asia Pacific Area.NX56 Chassis Signal Processing Introduction Brief introduction For different market requirements. maybe adopt different audio power amplifiers. they are use same main PCB board. one is for Latin America. so added AN5832SA to realize BTSC. NX56 Chassis not only match 21inches CRT. our design it in two versions. No matter NX56-AP what NX56-LA. The UOC for Latin America have CCD-Chip and BTSC function. NX56-LA and NX56-AP adopt different UOC. we call the chassis as NX56-AP. The others should be the same. . just different peripheral components. but the UOC for Asia Pacific region does not have the two functions but SECAM system is necessary. Due to different screen sizes. but also match 25 and 29inches CRT. we call the chassis as NX56-LA. and signal amplifying. The IF picture signal and sound signal formed in mixer and output from mixer.RF Section Tuner Tu101 receive the radio frequency signal. VGA (Fig. Tuner section) . then send to picture IF processing circuit. after inside circuit to do signal receiving. The amplified high frequency signal accompany with the high frequency oscillation voltage oscillated by set oscillator input to the mixer. 1. ) (Fig 2. Small Signal Processing Section) . get the color video broadcast signal and 2nd sound IF signal.Small Signal Processing Section Small signal processing section is the IF (intermediate frequency) signal across saw filter send in the pin12 and pin13 of IC201. sound trap. ( Refer to Fig2 and Fig 3. Video signal processing section is CVBS across video filter and delay line and horizontal & vertical synchronous separation circuit processing and get H-drive (pin56 of IC201)and V-drive signal (pin15/pin15 of IC201). The VIFIN signal through built-in PLL DEMOD. video amplifier and synchronous detector processing. IF sound signal across the sound-down-mixer and AM demodulator processing. send out the AVL/ SSIF OUT signal. to control the horizontal output transistor working in switch on and off situation. Block Diagram of IC201. get good linearly and enough amplitude of saw-tooth wave current to drive horizontal deflection yoke scanning. Pin11 of T401 sends out heater voltage supply for CRT heater.) Horizontal Scanning Section The horizontal drive signal send out from pin 56 of IC201. Q401 is horizontal driving transistor. Pin 10 of T401 get 200 Volt video amplifying voltage supply for CRT board.C457 are retrace capacitors.(Fig3. . D455 is damping diode. T401 is FBT.C455. Pin2 of T401 is B+ voltage input. L456 is horizontal width coil and L458 is horizontal linearly coil. coupled by horizontal driving transformer T402 . C453. D502 and D503 send to R. we use as differential-output driver. Pin 6 is boost voltage. Pin2(+14v) and Pin7(-14v) of IC301 is power supply which come from the main power transformer. B to discharge the electronic quickly.G. R306 is a damping resistor. At the right of turn off the TV. the current across D501. Vertical Scanning Processing Section CRT Scanning Section Q507. The vertical raw-tooth wave signal sends out from pin14/15 of IC201 VDA/VDB.Vertical Scanning Section Vertical scanning section adopted STV8172A vertical deflection booster. C306 is correction capacitor. R308 is current feedback resistor. Q507 is cut off. When the TV is playing mode.C301 and R305 makes up a voltage feedback network. +8V voltage across R533 charge for C512. .D501. C309. Q507 is turn-on. The two differential signal input pin 1 and 7 of STV8172A IC301. rectified by D301. Fig 4.D502 and D503 makes up a light eliminate circuit network. Pin5 of IC801 sends out the PWM signal to control Q801 working in switch on and off situation. D801-D804 is rectifying network. 300Vdc voltage supply pin3 of T801.CY802 makes up a common mode rejection network. .Audio Power Amplifying Section Power Supply Section AC supply 220V/110v through filtering network and rectifying circuit and get 300Vdc voltage. also through R804 send to pin8 of IC801 NCP1337. LF802 and CY801. LF801/LF801A and CX802 makes up a differential mode rejection. IC803 is optocoupler. . . . . . . . . This concept is intended for 90× picture tubes. The circuit has an audio switch for mono signals but the mono inputs can also be used as a stereo input. the other with (extended) OSD features (UOCTOP_OSD version). . The block diagram is given in Figure 1. The ICs have supply voltages of 8V.11 — 25 January 2007 Product data sheet 1. In this range most of the video and audio processing features have been omitted. All packages are according to the ROHS legislation. 0. This concept is intended for 90× picture tubes. The block diagram is given in Figure 1. The block diagram is given in Figure 2. which also means that these packages are lead-free. it has just stereo input switch and no audio control circuit. 5V and 3. • AV-90 concept. This new concept offers a complete range of products with the right price level to cover TV receivers from basic mono 14 inch sets up to the best featured large and/or wide screen AV-stereo TV sets. The UOC-TOP-64 concept can also be used as front-end for 2fH and LCD TV receivers. It contains a video processor with many features and it has an analog audio control circuit with balance.4 “Licenses”). treble. The only difference that it does not contain an East-West and Scan Velocity Modulation (SVM) output. Two different micro processor are available for this concept. Also this concept can be supplied with one of the two micro processors (UOCTOP_1PTXT or UOCTOP_OSD version). • Mono-90 concept. however. The functional content of this concept is comparable with that of the AV 110 concept. This concept is nearly identical to the AV-110 concept. UOC-TOP-64 is supported by a comprehensive Global TV Software Development kit to enable easy programming and fast time-to-market (see also Section 20. The UOC-TOP-64 concept is mounted in a SDIP64 package and is split up in the following ranges: • AV-110 (AV-stereo) concept.UOC-TOP-64 N1 series Versatile signal processor for CRT TV applications Rev. one with OSD and Closed Captioning or Teletext and Closed Captioning features (UOCTOP_1PTXT version). The most important features of the complete IC series are given in the following feature lists. • Mono-110 concept. bass and loudness control.3V. General description The UOC-TOP-64 series is a very flexible concept which offers attractive solutions for 1fH TV receivers with CRTs. 1 CVBS output.0/6. Video switch with 3 external CVBS inputs.72/5.74 MHz so that a second sound channel can be demodulated.1 Analog Video Processing 2. The SVM circuit is active for all the incoming CVBS.1. All rights reserved. The quality of this system is such that the external band-pass filters can be omitted. Teletext.7 MHz.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV 2. Automatic Y/C signal detector. AM demodulator without extra reference circuit The mono intercarrier sound circuit has a selective FM-PLL demodulator which can be switched to the different FM sound frequencies (4. The SVM output is combined with the black current input of the black current stabilisation circuit. Features 2. All CVBS inputs can be used as Y-input for Y/C signals. Scan Velocity Modulation output. Product data sheet Rev. The second stereo input is only available via the combined C2/C3/C4/AUDIOIN5R pin for the right channel and via the combined CVBS4/Y4/AUDIOIN5L pin for the left channel. CVBS3/Y3 input available in combination with the G/Y-3 input pin. By means of a small application adaptation both functions can be operational in parallel. In such an application it is necessary that an external bandpass filter is inserted. Audio switch circuit with 2 stereo inputs (1 stereo input can also be switched into two mono sound inputs) and a stereo output which can be used for the drive of for audio power amplifiers (with volume and tone-control) or as SCART/CINCH output. Y/C and RGB/YPBPR signals. which can be used as input for an external BTSC decoder or as input for external sound band-pass filter for second language processing. only 1 Y/C source can be selected because the circuit has 1 chroma input.V. Separate SSIF input available as input for the FM-PLL demodulator to demodulate FM-radio with an IF frequency of 10.5/6. However. <Document ID> © NXP B. The FM-PLL demodulator can be set to centre frequencies of 4. or as input from an external sound band-pass filter for second language processing.5 MHz).1 Overview of available features (AV-110/90 and Mono-110 concept) Multi-standard vision IF circuit with alignment-free PLL demodulator Internal (switchable) time-constant for the IF-AGC circuit Switchable group delay correction and sound trap (with switchable centre frequency) for the demodulated CVBS signal Separate Second Sound IF output or FM demodulator output without de-emphasis available. 2007.576 MHz) crystal required for the m-Controller.5/5.and the color decoder Multi-standard color decoder with automatic search system and various “forced mode” possibilities Internal base-band delay line Indication of the Signal-to-Noise ratio of the incoming CVBS signal Linear RGB/YPBPR input.11 — 25 January 2007 2 of 230 . 0. Integrated luminance delay line with adjustable delay time Only one reference (24. this output can be used as monitor video output or as front-end video output or as independent selectable video output. a mono output for SCART/CINCH with the possibility to serve as front/monitor audio output.and black stretching. CVBS output. 0. depeaking. bass and loudness controls 2.1. variable positive/negative peak ratio. which can also be switched into two mono sound inputs. The remaining video features are peaking with coring. white point and black level off-set adjustment so that the color temperature of the dark and the light parts of the screen can be chosen independently. When this ‘Continuous Cathode Calibration’ is not used. Stereo output (with volume and AVL) for audio power amplifiers.1. gamma control and blue. dynamic skin tone control. Y/C and RGB/YPBPR signals The effect of the various features can de demonstrated by means of a ‘split screen’ mode in which the features are activated in one half of the picture and switched off in the other half Switchable DC transfer ratio for the luminance signal Tint control for external RGB/YPBPR signals Contrast reduction possibility during mixed-mode of OSD and Text signals. This stereo output can also be switched to one mono loudspeaker output and one fixed mono sound output.V. 2007.4 Differences in feature list for the MONO-90 concept compared with AV-110/90 and Mono-110 concept Audio switch circuit with 1 stereo input. variable pre-/overshoot ratio and video dependent coring). simple alignment of the cutoff level is possible. Option to make a colored and in contrast reduced window. Only basic video processing.1.3 Features of the AV-110 and Mono-110 concept which are not available in the AV-90 concept Horizontal geometry processing and Scan Velocity Modulation output 2. Adjustable ‘wide blanking’ of the RGB outputs Horizontal synchronization with two control loops and alignment-free horizontal oscillator Vertical count-down circuit Vertical driver optimized for DC-coupled vertical output stages Horizontal and vertical geometry processing with horizontal parallelogram and bow correction and horizontal and vertical zoom The IC can be used as front-end for Progressive Scan or LCD TV receivers Low-power start-up of the horizontal drive circuit 2. black stretching and gamma control.11 — 25 January 2007 3 of 230 . <Document ID> © NXP B. No horizontal geometry processing and Scan Velocity Modulation output. RGB control circuit with ‘Continuous Cathode Calibration’. this output can only be used as monitor video output or as front-end video output. Product data sheet Rev. All rights reserved.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV Picture improvement features with peaking (with switchable centre frequency. All features are available for CVBS.2 Features of the AV-110/90 concept which are not available in the Mono-110 concept Analog audio tone control circuit with treble. G2 and G3 characters Signal quality detector for video and WST/VPS data types Comprehensive teletext language coverage Vertical Blanking Interval (VBI) data capture of WST data <Document ID> © NXP B.3 Data Capture (Teletext and Closed Caption devices) Text memory for 1 page Inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) Data Capture for US Closed Caption Data Capture for 525/625 line WST. Product data sheet Rev. to enable optimized m-processor throughput Automatic detection of FASTEXT transmission Real-time packet 26 engine in Hardware for processing accented.2 Micro-Controller 80C51 m-controller core standard instruction set and timing 0. VPS (PDC system A) and 625 line Wide Screen Signalling (WSS) bit decoding Automatic selection between 525 WST/625 WST Automatic selection between 625 WST/VPS on line 16 of VBI Real-time capture and decoding for WST Teletext in Hardware. Interrupt controller for individual enable/disable with two level priority Two 16-bit Timer/Counter registers One 24-bit Timer (16-bit timer with 8-bit Pre-scaler) 16-bit Data pointer WatchDog timer Auxiliary RAM page pointer Stand-by. 0. Idle and Power Down modes Up to 13 general-purpose I/O pins 14 bits PWM for Voltage Synthesis Tuning 8-bit A/D converter with 4 multiplexed inputs 4 PWM (6-bits) outputs for analogue control functions 2.9766 ms machine cycle maximum of 80 k x 8-bit late programmed ROM maximum of 3 k x 8-bit Auxiliary RAM I2C byte level bus interface. 2007. All rights reserved.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV 2.11 — 25 January 2007 4 of 230 .V. Product data sheet Rev. allowing four colors per character <Document ID> © NXP B.2 Features of the Teletext and Closed Caption devices Four character sets Up to 576 characters with a size of 12 pixels x 16 lines are supported Teletext and Enhanced OSD modes 50Hz/60Hz display timing modes Serial and Parallel Display Attributes Scrolling of display region Variable flash rate controlled by software Soft colors using CLUT with 4096 color palette Global selectable matrix: (12) Features of level 1. underlining and italics Soft colors using CLUT with 4096 color palette Global selectable matrix: (12/16) By attribute selectable: 1. allowing four colors per character 2. All rights reserved.4. 2007.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV 2.5x characters (18/24) Globally selectable character spacing Fringing (Shadow) selectable from N-S-E-W direction Fringe color selectable Contrast reduction of defined area with option of coloration Programmable Cursor Special Graphics Characters with two planes.1 Features of the OSD-only devices Up to 4 character sets with 256 characters each (size 16 pixels x 18 lines) Enhanced OSD modes 50Hz/60Hz display timing modes Serial and Parallel Display Attributes Single/Double Width and Height for characters Scrolling of display region Variable flash rate controlled by software Enhanced display features including overlining.4.5 WST and US Close Caption Single/Double/Quadruple Width and Height for characters 64 software redefinable On-Screen display characters G1 Mosaic graphics. Limited G3 Line drawing characters WST Character sets and Closed Caption Character set in single device Curtaining effect via software Fringing (Shadow) selectable from N-S-E-W direction Fringe color selectable Contrast reduction of defined area with option of coloration Programmable Cursor Special Graphics Characters with two planes. 0.V.4 Display 2.11 — 25 January 2007 5 of 230 . 6 − − 8. For a supply voltage of 8V the maximum output signal amplitude is 2 Vrms.3 − 3.7 − 3.11 — 25 January 2007 6 of 230 .0 V).3 V). The YPBPR input signal amplitudes are based on a color bar signal with 100% saturation.3 0.3 1. The AV-110/90 and Mono-110 versions need a supply voltage of 8 V. 0.3 V).0 V) digital supply VSP / analogue supply periphery supply current (3.2 − 1 − MAX. 5. 2007.0 0.0 1.0 0.4 − − 1.1 150 − 1.5 10 − 75 1.2 UNIT V mA V mA mA V mA mA W µV mV V V V V V V V V mV mV V V mA V mA mA mA Table 1: SYMBOL Supply VP IP VDDA IDDA IDDA VPAudio[1] IPAudio[1] IPAudio Ptot Input voltages ViVIFrms) ViSSIF(rms) ViAUDIO(rms) ViCVBS(p-p) ViCHROMA(p-p) ViRGB(p-p) ViY(p-p) ViPB(p-p) ViPR(p-p) Output signals Vo(IFVO)(p-p) Vo(QSSO)(rms) Vo(AMOUT)(rms) Vo(AUDIO)(rms)[1] Vo(CVBSO)(p-p) Io(AGCOUT) VoRGB(p-p) IoHOUT IoVERT IoEWD demodulated CVBS output (peak-to-peak value) sound IF intercarrier output (RMS value) demodulated AM sound output (RMS value) non-controlled audio output signals (RMS value) selected CVBS output (peak-to-peak value) tuner AGC output current range RGB output signal amplitudes (peak-to-peak value) horizontal output current vertical output current (peak-to-peak value) EW drive output current [1] The supply voltage for the analogue audio part of the mono-90 version can be 5V or 8V. All rights reserved.4 1. Product data sheet Rev.3 50 70 8.0 0.0 − − 4. 5.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV 3. AV-110/90 and mono-110 version total power dissipation video IF amplifier sensitivity (RMS value) sound IF amplifier sensitivity (RMS value) external audio input (RMS value) external CVBS/Y input (peak-to-peak value) external chroma input voltage (burst amplitude) (peak-to-peak value) RGB inputs (peak-to-peak value) luminance input signal (peak-to-peak value) PB input signal (peak-to-peak value)[2] PR input signal (peak-to-peak value)[2] MIN.7 1. mono-90 version supply current (8. AV110/90 and Mono110 versions audio supply voltage supply current (5.0 100 250 − 2.7 − − − − − − − − − − − − − − − 1. 4.0/8.0 160 3. For a supply voltage of 5V the maximum signal amplitudes at in and outputs are 1Vrms.V.7 0.0 − 0 − 10 − − TYP.0 1. [2] <Document ID> © NXP B. Mono90 version supply current (3. Quick reference data Quick reference data PARAMETER analogue supply voltage VSP supply current (5.7 2.0 0.0 V).0 − 1.8 − − − − − − − − 1 − − − 1. All rights reserved. 2007. YSYNC U/V TINT SATURATION RGB MATRIX BLUE/BLACK-STRETCH CVBS2/Y2 VIDEO SWITCH VIDEO IDENT. Fig 1. AVL/SSIFOUT/FMDEMOUT <Document ID> Product data sheet LS/SCART/CINCH -OUT SCART/CINCH IN I/Os NXP Semiconductors Block diagram SECAM L R AM DEMODULATOR SOUND PLL FM AM AUDIO SELECT DEEMPHASIS SOUND-DOWNMIXER LS AUDIO OUTPUT VOLUME/TONE**) CONTROL AVL IFVO/SVO/PIP CLK GENERATION RESET // I2C-BUS /// CLKI // CLKO TMSEL SDA/SCL CVBS IN CVBSREF SKIN TONE SAT Y DELAY ADJ. **) The mono-110 version has only volume control and no tone control functions Block diagram of the “AV-110/90” and “MONO-110” TV processor µ-PROCESSOR / TELETEXT DECODER / OSD Rev. 0. H/VDISPI IREFRGB R/G/B VDS CORB IREFO IREF RGB CONTROL OSD/TEXT INSERT /// CONTR/BRIGHTN INS.11 — 25 January 2007 BCLIN C2/C3/C4/ AUDIOIN5R VIDEO FILTERS CVBS4/Y4 AUDIOIN5L H/V SYNC SEP. + PLL 2nd LOOP H-SHIFT H-DRIVE V-DRIVE H-OUT EHTO RO/ GO/ BO/ PR Y PB B3/ PB-3 UOC-TOP-64 N1 series BLKIN/SVM/ VGUARD G3/ Y-3 EWD/AVL R3/ CVBS3/ PR-3/ Y3 C2/C3/C4 Signal processor for CRT TV © NXP B. H-OSC. PEAKING SCAN VELOCITY MODULATION AGCOUT PAL/SECAM/NTSC DECODER BASE-BAND DELAY LINE REF VIFIN VISION IF/AGC/AFC PLL DEMOD. 9 of 230 . ADJ. GAMMA CONTROL CSI CSO // H/VDISPO H/V VERTICAL & EAST-WEST GEOMETRY RGB/YPRPB SWITCH BRI CON.5. CCC/BLACK ADJ.V. SOUND TRAP GROUP DELAY VIDEO AMP. CIRN WHITE-P. 2007. H/V SYNC SEP. 0. SOUND TRAP GROUP DELAY VIDEO AMP. µ-PROCESSOR / TELETEXT DECODER / OSD Rev. All rights reserved. LS/SCART/CINCH -OUT SCART/CINCH IN SECAM L AVL <Document ID> AVL/SSIFOUT/FMDEMOUT Product data sheet NXP Semiconductors I/Os AM DEMODULATOR SOUND PLL FM AM AUDIO SELECT DEEMPHASIS LS AUDIO OUTPUT VOLUME/AVL CONTROL SOUND-DOWNMIXER IFVO/SVO AGCOUT PAL/SECAM/NTSC DECODER BASE-BAND DELAY LINE REF SATURATION RGB MATRIX BLACK-STRETCH GAMMA CONTROL CLK GENERATION RESET // I2C-BUS CLKI // CLKO TMSEL /// SDA/SCL CVBS IN CVBSREF Block diagram of the “MONO-90” TV processor SAT Y DELAY ADJ. H-OSC. CIRN WHITE-P. V-DRIVE H-OUT RO GO BO EHTO G3/ Y-3 R3/ CVBS3/ PR-3/ Y3 C2/C3/C4 B3/ PB-3 BLKIN/VGUARD CVBS4/Y4 VIDEO FILTERS CSI CSO // H/VDISPO H/VDISPI IREFRGB R/G/B VDS CORB IREFO IREF RGB CONTROL OSD/TEXT INSERT /// CONTR/BRIGHTN INS. CCC/BLACK ADJ. 10 of 230 . YSYNC CVBS2/Y2 C2/C3/C4/ VIDEO SWITCH VIDEO IDENT.Fig 2.11 — 25 January 2007 H/V VERTICAL RGB/YPRPB SWITCH BRI CON.V. + PLL 2nd LOOP H-SHIFT H-DRIVE UOC-TOP-64 N1 series BCLIN Signal processor for CRT TV © NXP B. PEAKING CORING VIFIN VISION IF/AGC/AFC PLL DEMOD. ADJ. 3/ADC3/PWM3 P3.3V) port 1.1/T0 P1.7 or I2C-bus data line port 1.6 or I2C-bus clock line port 1. Pinning information Table 6: SYMBOL AV-110 Mono-110 1 − 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 − 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Pinning information SDIP64 DESCRIPTION AV-90 Mono-90 1 − 2 3 4 5 6 7 8 9 10 11 12 13 14 15 − 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 − 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 − 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 IF video output / selected CVBS output / PIP output IF video output / selected CVBS output 2nd supply voltage TV processor (+5 V) 8 Volt supply for audio switches IF-PLL loop filter ground 2 for TV processor decoupling sound demodulator AVL / Second sound IF output / sound demodulator output EHT/overvoltage protection input tuner AGC output reference current input vertical sawtooth capacitor IF input 2 IF input 1 vertical drive A output vertical drive B output East-West drive output / AVL capacitor AVL capacitor bandgap decoupling SECAM PLL decoupling ground 1 for TV-processor phase-1 filter phase-2 filter 1st supply voltage TV-processor (+5 V) decoupling digital supply crystal oscillator output crystal oscillator input port 1.0/INT1 INT0/P0. All rights reserved.0/ADC0/PWM0 P2.11 — 25 January 2007 11 of 230 .6/SCL P1.1/PWM0 P2.5 port 3. 2007.3 or Counter/Timer 1 input port 1.5 (4 mA current sinking capability for direct drive of LEDs) supply © NXP B.1 or PWM0 output port 2.1 or Counter/Timer 0 input port 1.7/SDA P1.0/TPWM VDDP(3.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV 6.2 or ADC2 input or PWM2 output port 3.V.3V) <Document ID> Product data sheet Rev.0 or external interrupt 1 external interrupt 0 or port 0.3 or ADC3 input or PWM3 output port 3.3V) P1. 0.1 or ADC1 input or PWM1 output port 3.2/ADC2/PWM2 P3.3/T1 P1.5 VDDC(3. IFVO/SVO/PIP [3] IFVO/SVO [3] VP2 VCC8V PLLIF GND2 DECSDEM AVL/SSIFOUT/SNDDEMOUT[2] EHTO AGCOUT IREF VSC VIFIN2 VIFIN1 VDRA VDRB EWD/AVL AVL DECBG SECPLL GND1 PH1LF PH2LF VP1 DECDIG XTALOUT XTALIN P1.0 or Tuning PWM output supply to periphery (3.0 or ADC0 input or PWM0 output port 2.5 P3.1/ADC1/PWM1 P3. V.NXP Semiconductors UOC-TOP-64 N1 series Signal processor for CRT TV Table 6: SYMBOL Pinning information AV-110 Mono-110 41 42 43 44 − 45 − 46 − 47 − 48 49 50 51 52 53 54 55 56 57 58 59 60 − 61 62 63 64 − SDIP64 DESCRIPTION AV-90 Mono-90 41 42 43 44 − 45 − 46 − − 47 48 49 50 51 52 53 54 55 56 57 58 59 60 − 61 62 63 64 − 41 42 43 − 44 − 45 − 46 − 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 − 64 ground OTP Programming Voltage supply voltage Blue output / PB output Blue output Green output / Y output Green output Red output / PR output Red output black current input / vertical guard / scan velocity modulation output black current input / vertical guard beam current limiter input 3rd B input / PB input 3rd G input / Y input / CVBS input / Y input 3rd R input / PR input / C2/3/4 input Y-output (for YUV interface) Y-input for sync separator supply voltage (5 V) ground connection horizontal output flyback input/sandcastle output audio output for audio power amplifier (right signal) or fixed audio output for mono applications audio output for audio power amplifier (left signal) or speaker output for mono applications chroma-2/3/4 input / audio 5 right input chroma-2/3/4 input audio 3 input / right stereo input CVBS2/Y2 input audio 2 input / left stereo input / sound IF input CVBS4/Y4 input / audio 5 left input CVBS4/Y4 input GND5 VPE VDDA1(3. Therefore this pulse must end before line 14. <Document ID> © NXP B. The function of this pin is selected by means of the CMB2-0 bits The function of this pin is selected by means of the SVO1-0 bits The SSIF input is selected by means of the SSIFM bit The choice between two mono inputs or one stereo input is realized by means of the bits SAS3-0 The black current input. 2007. For a reliable operation of the protection system and the black current stabilization system or SVM system.3V) BO/PBOUT BO GO/YOUT GO RO/PROUT RO BLKIN/VGUARD/SVM [1][6] BLKIN/VGUARD [1][6] BCLIN B3/PB3 G3/Y3/CVBS3/Y3 [1] R3/PR3/C2/C3/C4 [1] YOUT YSYNC VP3 GND3 HOUT FBISO/SANDCA AUDOUTSM2/LSR AUDOUTLSM1/LSL C2/C3/C4/AUDIOIN5R [1] C2/C3/C4 AUDIOIN3/IN1R [5] CVBS2/Y2 AUDIOIN2/IN1L/SSIF [4][5] CVBS4/Y4/AUDIOIN5L [1] CVBS4/Y4 [1] [2] [3] [4] [5] [6] The function of these pins is dependent on some I2C-bus control bits. the end of the vertical guard protection pulse during normal operation should not overlap the measuring pulses. vertical guard input and SVM output (AV-110/90 and Mono-110 versions) have been combined on this pin. 0. All rights reserved. More details are given in Table 7.11 — 25 January 2007 12 of 230 . Product data sheet Rev. 0 ADCS No. This device.5 App output current to drive the vertical deflection yoke. provides up to 2.® STV8172A Vertical Deflection Booster for 3-APPTV/Monitor Applications with 75-V Flyback Generator PRODUCT PREVIEW Main Features ■ Power Amplifier ■ Flyback Generator ■ Stand-by Control ■ Output Current up to 3 App ■ Thermal Protection HEPTAWATT (Plastic Package) ORDER CODE: STV8172A Description The STV8172A is a vertical deflection booster designed for TV and monitor applications. In double-supply applications. Details are subject to change without notice. The internal flyback generator delivers flyback voltages up to 75 V. a stand-by state will be reached by stopping the (+) supply alone. Tab connected to pin 4 7 6 5 4 3 2 1 Input (Non Inverting) Output Stage Supply Output Ground Or Negative Supply Flyback Generator Supply Voltage Input (Inverting) Output Stage Supply 6 Flyback Generator 3 Supply Voltage 2 Non-Inverting Input Inverting Input Flyback Generator 7 + Power Amplifier 5 Output 1 Thermal Protection 4 STV8172A Ground or Negative Supply August 2003 Revision 1. . supplied with up to 35 V. 7564264 STMicroelectronics Confidential 1/14 This is preliminary information on a new product now in development. All pins have a reverse diode towards pin 4. 2 Thermal Data Symbol RthJC TT TJ Parameter Junction-to-Case Thermal Resistance Temperature for Thermal Shutdown Recommended Max. Note 3 and Note 6 Amplifier Input Voltage . 4. 2. Note 6 and Note 7 40 70 -0.Note 2 Voltage at Pin 3 . This non-repetitive output peak current can be observed. 5. 6. V3 is higher than VS during the first half of the flyback pulse. Junction Temperature Value 3 150 120 Unit °C/W °C °C 2/14 STMicroelectronics Confidential . for example.Note 4 ±5 ±2 2 2 ±5 A A A A A Supply Voltage (pin 2) . during the Switch-On/SwitchOff phases. V7 Current I0 (1) I0 (2) I3 Sink I3 Source I3 ESD Susceptibility ESD1 ESD2 Temperature Ts Tj Storage Temperature Junction Temperature -40 to 150 +150 °C °C Human body model (100 pF discharged through 1.Absolute Maximum Ratings STV8172A 1 Absolute Maximum Ratings Symbol Parameter Value Unit Voltage VS V5. Usually the flyback voltage is slightly more than 2 x VS. 7. This must be taken into consideration when setting VS.Note 4 Output Peak Current non-repetitive . This peak current is acceptable providing the SOA is respected (Figure 8 and Figure 9). t £ 10µs .4 to (VS + 3) . Input voltages must not exceed the lower value of either VS + 2 or 40 volts. these diodes should never be forward-biased.4 to (VS + 2) or +40 V V V V Note:1. t < 1ms Flyback pulse current at f=50 to 200 Hz. Versus pin 4 3. t<1ms . t£10ms .Note 1 and Note 2 Flyback Peak Voltage . Such repetitive output peak currents are usually observed just before and after the flyback pulse. V6 V3 V1.Note 2.5 kW) EIAJ Standard (200 pF discharged through 0 W) 2 300 kV V Output Peak Current at f = 50 to 200 Hz.Note 2.Note 5 Sink Current.Note 3 Source Current.0. Operating Supply Voltage Range (V2-V4) Pin 2 Quiescent Current Pin 6 Quiescent Current Note 8 I3 = 0.6 -1.V4) = 35 V is not allowed without special circuitry. V7 = 2.3 2.2 V V1 = 2.5 A I3 = 20 mA I3 = -1. (VS . TAMB = 25°C.2 1 2.V4). V6 =35v 10 5 8 19 35 20 50 V mA mA 1 1 V1 = 1 V. I5 = 0.0. 9. Unit Fig.5 1. Refer to Figure 4.5 A I5 = -1.0.6 . the peak flyback voltage is slightly greater than 2 x (VS . I5 = 0 I3 = 0. Max.8 1.STV8172A Electrical Characteristics 3 Electrical Characteristics (VS = 34 V. unless otherwise specified) Symbol Supply VS I2 I6 Input I1 I7 VIR VI0 DVI0/dt Output I0 V5L V5H Stand-by V5STBY Input Bias Current Input Bias Current Parameter Test Conditions Min.1 2.5 A I3 = 1. Typ.2 V.4 2.5 A 80 1.5 A 1 1.7 2.2 µA µA 1 Operating Input Voltage Range Offset Voltage Offset Drift versus Temperature V mV µV/°C 2 10 Operating Peak Output Current Output Saturation Voltage to pin 4 Output Saturation Voltage to pin 6 0o<Tcase<125oC I5 = 1.6 0.2 V Miscellaneous G VD5-6 VD3-2 V3SL V3SH Voltage Gain Diode Forward Voltage Between pins 5-6 Diode Forward Voltage between pins 3-2 Saturation Voltage on pin 3 Saturation Voltage to pin 2 (2nd part of flyback) I5 = 1.8 ±1.5 VS . Therefore.5 -1. STMicroelectronics Confidential 3/14 . In normal applications. Stand-by condition.8 dB V V V V 3 8.3 A V V 3 2 Output Voltage in Stand-by V1 = V7 = VS = 0 See Note 9 VS . V7 = 1 V 0 . I5 4 2.2V STV8172A S 1 4 39kW (a) (b) I1 1V 5.2V 4 V3L V5L (a): V5L measurement (b): V3L measurement 4/14 STMicroelectronics Confidential . I2 and I6 +Vs I2 2 7 I6 6 5 2.Electrical Characteristics STV8172A Figure 1: Measurement of I1.6kW (a): I2 and I6 measurement (b): I1 measurement Figure 2: Measurement of V5H +Vs 2 7 6 V5H 5 .2V STV8172A 1 1V Figure 3: Measurement of V3L and V5L +Vs 2 7 6 (b) 3 I3 or I5 (a) 1V STV8172A 5 1 2. A Stand-by state will be reached by switching OFF the positive supply alone.22µF Rd(*) Yoke Ly 470µF 0.1 DC-coupled Application When DC coupled (see Figure 4). the output will sink negligible current from the deviation coil. where both inputs are the same voltage as pin 2 or higher.1µF R2 R1 (*) recommended: Ly Ly ------------. where the feedback loop maintains V1 = V7.1 Application Hints For calculations.1. STMicroelectronics Confidential 5/14 . 4.1µF 6 Vref Vertical Position Adjustment Power Amplifier 7 + 5 1 VM Vm -VEE 4 R3 Thermal Safety CF (47 to 100µF) 3 2 Flyback Generator Output Voltage Output Current Ip 1.5W 0. On the other hand. the display vertical position can be adjusted with input bias.< Rd < ------------50 m s 20 m s 4. treat the IC as an op-amp. In this state. Figure 4: DC-coupled Application +Vs 470µF 0.STV8172A Application Hints 4 Application Hints The yoke can be coupled either in AC or DC. 2 supply sources (VS and -VEE) are required. ´ ------. Of course.1. such that (R8 / R7) = (R3 / R2). then R3 = 15 kW Finally.2 Peak Current ( VM – V m ) R2 I P = ---------------------------. For that purpose. for instance R1=1 W From equation of peak current: R2 2 ´ IP ´ R1 2 ------.´ ç ---------------------÷ 2 è R 2 + R 3ø 4.1 Centering STV8172A Display will be centered (null mean current in yoke) when voltage on pin 7 is (R1 is negligible): VM + Vm æ R2 ö V 7 = -----------------------.1.= -R3 3 V M – Vm Then choose R2 or R3. and connect the bias filtering capacitor between the intermediate point and the local driver ground.2 Ripple Rejection When both ramp signal and bias are provided by the same driver IC.= --. you can gain natural rejection of any ripple caused by a voltage drop in the ground (see Figure 5).= ---------------------------. R7 should be connected to the booster reference point.1. For instance. arrange an intermediate point in the bias resistor bridge.1. if you manage to apply the same fraction of ripple voltage to both booster inputs.´ -----------------2 R xR 1 3 Example: for Vm = 2 V.= 1.´ ----------------.4V 2 2.5 2 R 3 1 + ------R2 4. which is the ground side of R1. VM = 5 V and IP = 1 A Choose R1 in the1 W range. the bias voltage on pin 7 should be: VM + Vm 7 1 1 V 7 = -----------------------. if R2 = 10 kW.Application Hints 4.1. Figure 5: Ripple Rejection 6 Reference Voltage Power Amplifier 7 R9 R8 R7 1 + 3 2 Flyback Generator 5 Thermal Safety 4 Rd Yoke Ly Ramp Signal R3 R2 R1 Driver Ground Source of Ripple 6/14 STMicroelectronics Confidential . 1 Application Hints Gain is defined as in the previous case: R V –V 2 M m I p = ----------------------.= ------------------------------------.5W 0.– V 7 V – -----------------------. For good output centering.2 AC-Coupled Applications In AC-coupled applications (See Figure 6).+ ------.´ --------------------R1 ´ R3 2 Choose R1 then either R2 or R3.+ ------------------------÷ 2 ´ R 2 ( R + R ) è 3 ø 4 5 STMicroelectronics Confidential 7/14 . usually some current is injected or sunk with a resistor in the low side of the yoke).1µF 6 CF (47 to 100µF) +Vs Output Voltage 3 2 Flyback Generator Output Current Ip Power Amplifier 7 + 5 1 VM Vm R3 Thermal Safety 4 1. only one supply (VS) is needed.22µF Rd(*) Yoke Ly R5 Cs R4 CL (*) recommended: Ly Ly -----------. V7 must fulfill the following equation: V +V V M m S ------.< Rd < ------------20 m s 50 m s R2 R1 4. The vertical position of the scanning cannot be adjusted with input bias (for that purpose.2.STV8172A Application Hints 4.+ ---------------------ö = èR R2 R + R ø 3 4 5 V +V ö V æ M m S ç -----------------------------. Figure 6: AC-coupled Application 470µF 0.V 7 2 7 2 --------------------.+ ------R3 R2 R4 + R5 or 1 1 1 V 7 ´ æ ------. Figure 7: Using a Differential-output Driver +Vs 470µF 0.< Rd < ------------20 m s 50 m s R1 Let us set some definitions: ● icm is the common-mode current: 1 i cm = -. 8/14 STMicroelectronics Confidential .5W 0. as two current sources i+ and i.(ip) = 2 ip.1µF 6 Differential output driver IC Power Amplifier ip icm + CF (47 to 100µF) Output Voltage 3 2 Flyback Generator Output Current Ip 7 R7 1 + 5 4 Thermal Safety 1.= icm .(i + i ) 2 + - ● at peak of signal.22µF Rd(*) icm -ip Yoke Ly - -VEE 470µF 0. 4. i+ = icm + ip and i.ip. The application is described in Figure 7 with DC yoke coupling. therefore the peak differential signal is ip . therefore the amount of S correction is set by the combination of CL and Cs. and the peak-peak differential signal. The calculations still rely on the fact that V1 remains equal to V7.1µF R2 (*) recommended: Ly Ly ------------. 4ip.3 Application with Differential-output Drivers Certain driver ICs provide the ramp signal in differential form.with opposite variations.Application Hints STV8172A CS performs an integration of the parabolic signal on CL. . . . 3MM BK 01 TV RAW BRACKET -.-.REAR CABINET(ART)ASY DEC BACKCOVER -.-.00 00 R=N LENS TV DEC KEY CLUSTER 29M76S -.REAR CABINETASY TV RAW FELT PAPER 150MMX19MMX0.8MM) TWIST TIE NY66 RUBBER PAD (25MMX7MM) RUBBER PAD (22X22X5MM) TCL62-216340-0UN= BLOCK R=N TV RAW FASTENER CRT DEGAUSSING COIL 25"" CRT SUPPORT SCREW-ST 4MM 15MM ISO 62 R=Y MACHINE SCREW S/T SCREW W 3 X 10 AB S/T SCREW W 3 X 10 AB S/T SCREW W 3 X 12 AB S/T SCREW W 3 X 12 AB S/T SCREW HA 6X30 SPRING CRT 6MMX50MMX0.00 R=Y TV PRI OVERLAY REAR AV BLACK&WHITE 00 00 ASS'Y .A8252 01 00 00 R=N TV DEC OVERLAY 29M62S -.CAB MTG FBT MTG FC&RC MTG RC&R AV BKT .REMOTE 016W31-A012X LOGO:RCA RCT NX56&NX56B JY-T03101-018 ASS'Y .00 00 R=N TV RAW BRACKET -.CAB MTG CRT SUPPORT TO FC MTG SPEAKER TO FC MTG LENS PCB TO FC MTG LENS TO FC MTG PUSH BUTTON TO FC MTG SIDE AV BRK TO FC MTG CRT TO FC MTG TO FRONT.FRONT CABINET(ART)ASY DEC BACKCOVER -.00 00 00 R=Y RCA LOGO TV RAW FELT PAPER 150MMX19MMX0.FRONT CABINETASY B121 DEGAUSSING COIL XC-29" SPEAKER YDP616-5A SPEAKER YDP616-5A HS 2P22 700/7 TJC3-2Y HS 3PIN TCL1073 TV RAW INSULATOR SLEEVE AWG#5 -.: MATERIAL NAME: WERK:1034 parent 03-BM62SAE-CL12S T6-016W31-AAT1X 03-BM62SAE-CL12S T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4Z T8-29M62AE-FC4Z T8-29M62AE-FC4Z T8-29M62AE-FC4Z T8-29M62AE-FC4Z T8-29M62AE-FC4Z T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 T8-29M62AE-FC4 03-BM62SAE-CL12S T8-29M62AE-RC5 T8-29M62AE-RC5 T8-29M62AE-RC5 T8-29M62AE-RC5 T8-29M62AE-RC5 T8-29M62AE-RC5Z T8-29M62AE-RC5Z T8-29M62AE-RC5Z 03-BM62SAE-CL12S T8-29M62AE-PA3 T8-29M62AE-PA3 T8-29M62AE-PA3 child T6-016W31-AAT1X 06-016W31-A012X T8-29M62AE-FC4 41-GND029-LX0 36-DEG290-XX2L 42-61608F-XX1G 42-61608F-XX1G 46-35197H-02XG 46-CT048T-03H01G 54-113970-0U0 54-205140-000 54-314740-0X0 57-10654X-00F 59-130460-00X 59-377680-000 62-216340-0UN 62-321780-0HG 62-444980-0CN 63-B40150-AB4G 63-S40120-BT4G 63-W30100-AB4G 63-W30100-AB4G 63-W30120-AB4G 63-W30120-AB4G 63-Z60300-AB4G 67-X21679-0E0 T8-29M62AE-FC4Z 55-BM62FC-2CL9B 56-445230-4HN6R 56-B192LE-0HC5Z 56-LM62FB-0HA6M 58-LM62FI-2UI9E 67-L82843-0N01A 54-114000-00X 62-455090-0UN 62-455100-0UN 62-407210-0UN T8-29M62AE-RC5 54-114000-00X 63-B40150-AB4G 63-B40200-AB3G 63-F30100-BT3G T8-29M62AE-RC5Z 55-BM62RC-5CL6R 58-456790-2UI9A 58-BM62MP-JKC9K T8-29M62AE-PA3 75-450400-EC0 75-450410-EC0 75-450420-EC0 03-BM62SAE-CL12S FORCAST BOM BOM APPLICATION:PP01 description TV ASY .10 MATERIAL BOM PRINT MATERIAL NO.2009.00 00 R SPACER CRT MOUNTING T=2MM CRT FIBRE SHEET (22MMX22MMX0.3MM BK 01 SCREW-ST 4MM 15MM ISO 62 R=Y SCREW-ST 4MM 20MM JIS B 1122 12 R=Y SCREW-ST 3MM 10MM ISO 65 0 0 R=Y ASS'Y .Q0003 01 9B 00 R=N TV PRI FASTENER CABLE-STRAP -.CAB MTG CRT&F.00 00 R=N POWER SUPPLY BRACKET ASS'Y .6MM ASS'Y .11.PACKINGASY POLYFOAM POLYFOAM POLYFOAM BOM text SP601 SP602 S601A TO R_SPK S602 TO L_SPK FOR SPEAKER WIRE MTG CRT & FC MTG CRT & FC STICK ON FC FOOT FOR CRT SUPPORT MTG TO FRONT.00 6M 00 R= TV DEC OVERLAY 29M62 -. MATCH TUBEKIT ASS'Y .6KV +/-5% CAP.MOF 27 OHM 1W +-/5% RES.9K 1/6W+/-1% RES.5OHM +/-5% 2W R=Y RMOF 3. 330 OHM 1/6W +/-5% CAP. M.6KV +/-5% COIL LINEARITY 15 UH FBT SANHUA NX56 BSC27-0109X TCL36-WID801-XX1= COIL WIDTH 800 UH R=N RES. C.6KV +/-5% RMOF 1.5V ASS'Y .0072UF 1.F.PP 0.F 3.T8-29M62AE-PA3 T8-29M62AE-PA3 T8-29M62AE-PA3 T8-29M62AE-PA3 T8-29M62AE-PA3Z T8-29M62AE-PA3Z T8-29M62AE-PA3Z T8-29M62AE-PA3Z T8-29M62AE-PA3Z T8-29M62AE-PA3Z T8-29M62AE-PA3Z 03-BM62SAE-CL12S T8-29RFLT-LGHAE1 T8-29RFLT-FLGHAE T8-29RFLT-LGHAE1 75-450430-EC0 75-450450-EC0 49-R03P80-BAT T8-29M62AE-PA3Z 74-022032-6WEEM 74-130130-80HEM 76-450440-0AT8H 71-BM62SA-ODF1A 72-BM62LA-S129C 71-RCACHI-SER7L 71-RCACHI-SER7M T8-29RFLT-LGHAE1 T8-29RFLT-FLGHAE 44-29RFLT-LGHA POLYFOAM POLYFOAM BATTERY 1.F. C.PP 0. 270 OHM 1/2W TCL20-TR102H-5CX= TRIMMER B1K HORIZ TYPE RES. M.E 0.5OHM +/-5% 2W R=Y RMOF 1.FUSE 1K OHM 1/2W +/-5% TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R RES. C. P. M. M.PP 9100 PF 1.PACKING(ART)ASY PRI BAG -.M.022 UF 400V +/-5% CAP.MATCH TUBE (F.F. C.RED 186C 01 00 00 R=N DEC BAG 130X130CM RED 186C 00 EM 00 R=Y DEC CARTON-BOX 29M62 CA 00 8H 00 R=Y TV PRI LABEL 29M62 WHITE&BLACK R=Y IB OPERATION MANUAL RCA SPANISH R=Y PRI LABEL 29M62 WHITE&BLACK R=Y PRI LABEL 29M62 WHITE&BLACK R=Y ASS'Y .PP 3300PF 1.CAB)KIT CRT A68QGU820X 08T SH RF UD T8-29RFLT-MLGHAE1 ASS'Y .F.82OHM +/-5% 1W KN1 CAP.MATCH TUBE (MAIN BD)KIT CAP.3K OHM 1/6W +/-5% TCL18-CE0271-JNX= RES.9OHM +/-5% 2W R=Y RESISTOR WIRE WOUND 0. 3.0022UF 63V +/-5% C454 C453 C455 L458 T401 L451 R459 R416 R306 VR801 R833 R455A R319 R320 R402 R420 C457 R317 R318 R425A R308A C406 T8-29RFLT-MLGHAE1 27-AHQ223-JSX T8-29RFLT-MLGHAE1 27-ALQ332-J0X T8-29RFLT-MLGHAE1 27-ALR722-J0X T8-29RFLT-MLGHAE1 36-LIN150-XX1 T8-29RFLT-MLGHAE1 37-FCAT01-EAA9A T8-29RFLT-MLGHAE1 36-WID801-XX1 T8-29RFLT-MLGHAE1 18-CB0563-JNX T8-29RFLT-MLGHAE1 18-CB0332-JNX T8-29RFLT-MLGHAE1 18-CE0271-JNX T8-29RFLT-MLGHAE1 20-TR102H-5CX T8-29RFLT-MLGHAE1 18-DB0392-FNX T8-29RFLT-MLGHAE1 18-EE0102-JS2 T8-29RFLT-MLGHAE1 41-WJ0050-B00 T8-29RFLT-MLGHAE1 41-WJ0050-B00 T8-29RFLT-MLGHAE1 18-FF0270-JSX T8-29RFLT-MLGHAE1 18-CB0331-JNX T8-29RFLT-MLGHAE1 27-ALR912-J0X T8-29RFLT-MLGHAE1 18-FG0159-JSX T8-29RFLT-MLGHAE1 18-FG0159-JSX T8-29RFLT-MLGHAE1 18-FG0399-JSX T8-29RFLT-MLGHAE1 18-RF0828-JSX T8-29RFLT-MLGHAE1 27-PBC222-J0X . 56K OHM 1/6W +/-5% RES. PP 680NF 400V +/-5% 29"CRT BDEQU TRANSISTOR BF422 (NPN) 126 TRANSISTOR BF422 (NPN) 126 TRANSISTOR BF422 (NPN) 126 TRANSISTOR BF423 (PNP) 126 TRANSISTOR BF423 (PNP) 126 TRANSISTOR BF423 (PNP) 126 TR 50VV 150MA_A NPN 0.F. C. 47 OHM 1/6W +/-5% RES. C.F.F. CER 390PF 50V +/-5% CAP. C.F. M. CER 470 PF 50V +/-5% 1 R=N 1 R=N 1 R=N WIREBAREJUMPER9MM WIREBAREJUMPER10MM SMD PIN BASE *1 TJC1-1A PIN BASE *6 TJC3-6A PIN BASE TJC3-4A SOCKER CRT GZS10-2-AD2 COIL CHOKE 47 UH +/-10% RMOF 15KOHM +/-5% 2W R=Y RMOF 15KOHM +/-5% 2W R=Y RMOF 15KOHM +/-5% 2W R=Y WIREBAREJUMPER7.MATCH TUBE (DPC BD)KIT CAP.F. C. C. C.F. 1K OHM 1/4W +/-5% RES. 470 OHM 1/4W +/-5% RES.CER 1N0F 2KVV CAP. 47 OHM 1/6W +/-5% RES.F.4W 80MHZ TO-92 2SC TR 50VV 150MA_A NPN 0. C. C. C. C. C. CER 390PF 50V +/-5% CAP. 750 OHM 1/6W +/-5% C431 C433 Q512 Q522 Q532 Q513 Q523 Q533 Q501 Q502 Q503 Q531A Q521A Q511A R513 R523 R533 R511 R521 R531 R532 R522 R512 R541 R538 R536 R528 R526 R518 R516 R506 R539 R529 R519 C505 C521 C511 C531 D531 D521 D511 J502 J503 P503 P501 P502 S501 L501 R515A R525A R535A J504 R501 R502 R503 T8-29RFLT-DLGHAE1 27-AHR474-JSX T8-29RFLT-DLGHAE1 27-AHR684-JSX T8-29RFLT-LGHAE1 T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K T8-0NX56B-CR2K 11-0BF422-0BX 11-0BF422-0BX 11-0BF422-0BX 11-0BF423-0BX 11-0BF423-0BX 11-0BF423-0BX 11-SC1815-YBX 11-SC1815-YBX 11-SC1815-YBX 11-SC4544-0AX 11-SC4544-0AX 11-SC4544-0AX 18-CB0221-JNX 18-CB0221-JNX 18-CB0221-JNX 18-CB0470-JNX 18-CB0470-JNX 18-CB0470-JNX 18-CB0471-JNX 18-CB0471-JNX 18-CB0471-JNX 18-CD0102-JNX 18-CD0471-JNX 18-CD0471-JNX 18-CD0471-JNX 18-CD0471-JNX 18-CD0471-JNX 18-CD0471-JNX 18-CE0224-JNX 18-FE0272-JNX 18-FE0272-JNX 18-FE0272-JNX 26-AMM102-KRX 26-EBP391-JCS 26-EBP391-JCS 26-EBP471-JCS 41-WJ0065-B00 41-WJ0065-B00 41-WJ0065-B00 41-WJ0090-B00 41-WJ0100-B00 46-10967W-01XG 46-33079W-06XG 46-35179W-04XG 47-CRT004-XX3G 34-A470K0-1IX 18-FG0153-JSX 18-FG0153-JSX 18-FG0153-JSX 41-WJ0075-B00 18-CB0751-JNX 18-CB0751-JNX 18-CB0751-JNX . 750 OHM 1/6W +/-5% RES. C. C.PP 0.F.T8-29RFLT-LGHAE1 T8-29RFLT-DLGHAE1 ASS'Y . 470 OHM 1/4W +/-5% RES. 220K OHM 1/2W +/-5% RESISTOR METAL OXIDE FILM 2K7OHM 5% 1/2W RESISTOR METAL OXIDE FILM 2K7OHM 5% 1/2W RESISTOR METAL OXIDE FILM 2K7OHM 5% 1/2W CAP.4W 80MHZ TO-92 2SC TR 50VV 150MA_A NPN 0. C.F. 470 OHM 1/4W +/-5% RES.F. 470 OHM 1/4W +/-5% RES. 220 OHM 1/6W +/-5% RES. 470 OHM 1/6W +/-5% RES.F.F. C.F. 47 OHM 1/6W +/-5% RES. 470 OHM 1/6W +/-5% RES. 470 OHM 1/4W +/-5% RES. C.F. 220 OHM 1/6W +/-5% RES.F. 220 OHM 1/6W +/-5% RES. C. 750 OHM 1/6W +/-5% RES. C.5MM RES.F. 470 OHM 1/4W +/-5% RES.47UF 400V +/-5% CAP.F. 470 OHM 1/6W +/-5% RES.F.4W 80MHZ TO-92 2SC TRANSISTOR 2SC4544 TRANSISTOR 2SC4544 TRANSISTOR 2SC4544 RES. C.F.F. C. F.CER. RES 100K OHM 1/10W 0603 SMD.SMD 47PF 50V +/-5% 0603 SMD.SMD 100N0F 50V DCV 0603 CAP. ELEC 47 UF 16V +/-20% TV PCB IR BD R=Y WIRE 导电 350MM 04 TJC3 JC25 2.SMD 100N0F 50V DCV 0603 CAP.CER.T8-0NX56B-CR2K T8-0NX56B-CR2K 03-BM62SAE-CL12S T8-BM62SAE-MA3SM T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-29M62AE-IR1 T8-BM62SAE-MA3SM T8-29F5AE-SI1 T8-29F5AE-SI1 T8-29F5AE-SI1 T8-BM62SAE-MA3SM T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 40-0NX56B-CRD1XG 26-EBP561-JCS T8-BM62SAE-MA3SM T8-29M62AE-IR1 02-IRR001-XX1 11-SC1815-YBX 14-LED03R-XX1 18-CB0100-JNX 18-CB0103-JNX 18-CB0681-JNX 25-HCB470-M1X 40-00TB97-IRA1XG 46-CE035T-04K01G T8-29F5AE-SI1 40-029M71-SIA1XG 46-CD055T-05K01G 47-RCA020-XX1G T8-DM63SAE-BT1 12-BC847B-0BX 13-74HC40-53B 13-AN5832-SAB 19-AB0100-JTX 19-AB0101-JTX 19-AB0101-JTX 19-AB0103-JTX 19-AB0103-JTX 19-AB0104-JTX 19-AB0104-JTX 19-AB0184-JTX 19-AB0332-JTX 25-BCB101-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB229-M1X 25-BFB229-M1X 25-BFB479-M1X 25-BFB229-M1X 25-BFB339-M1X 25-BFB229-M1X 28-AA0224-KBX 28-AB0104-ZFX 28-AB0104-ZFX 28-AB0104-ZFX 28-AB0104-ZFX 28-AB0104-ZFX 28-AB0104-ZFX 28-AB0104-ZFX 28-AB0223-ZFX 28-AB0333-ZFX 28-AB0470-JCX 28-AB0470-JCX 28-AC0334-ZFX 28-AC0334-ZFX 19-AB0104-JTX 19-AB0104-JTX 19-AB0101-JTX 25-BCB101-M1X 45-FIL4M5-0Y1 TV PCB CR BD R=Y CAP.2 UF 50V +/-20% CAP.SMD 100N0F 50V DCV 0603 CAP.SMD 100N0F 50V DCV 0603 CAP.SMD 100N0F 50V DCV 0603 CAP. CAP 0. 10K OHM 1/6W +/-5% RES.ELE 5MM 100UF 16VV 5X11 85 / CERAMIC FILTER SFSH4.SMD 33N0F 50.33UF 16VDC +80%/-20% SMD.SMD 47PF 50V +/-5% 0603 CAP. ELEC 10 UF 50V +/-20% CAP.2 UF 50V +/-20% CAP.4W 80MHZ TO-92 2SC LED RED Φ3MM FO203 RES.CER.RECEIVE BDEQU IR RECEIVER MODULE HRM380017 TR 50VV 150MA_A NPN 0.0V 0603 -CAP.5MM UL#246 RCA SOCKET Y/W/R ASS'Y .F. ELEC 2. ELEC 10 UF 50V +/-20% CAP. 680 OHM 1/6W +/-5% CAP. CAP 0.0V 0603 CAP.ELE 5MM 3. ELEC 2. C.CER.BTSC BDEQU TR-SMD NPN 45VV 100MA_A 100HZ 0.SMD 22N0F 50.CER.SMD 220N0F 10.2 UF 50V +/-20% CAP. ELEC 2.2 UF 50V +/-20% CAP. CEP 560PF 50V +/-5% ASS'Y .CER.F.CER. ELEC 10 UF 50V +/-20% CAP.ELE 5MM 100UF 16VV 5X11 85 / CAP.CHASSIS BDKIT ASS'Y .CER. C.SIDE AV BDEQU TV PCB SI BD R=Y WIRE 导线 550MM 05 TJC3 SCN 2. 10 OHM 1/6W +/-5% RES.SMD 100N0F 50V DCV 0603 CAP.5MM UL#24 ASS'Y . C. RES 100K OHM 1/10W 0603 RES SMD 100 OHM 1/10W 0603 CAP.3K OHM 1/10W 0603 CAP.5MDB C541 IR1001 Q111 D1012 R1011 R013 R1012 C1012 S1001 TO P202(PIN1PIN4) P1903 TO P902 P1901 Q703 IC702 IC701 R704 R701 R702 R717 R708 R715 R714 R703 R706 C710 C736 C735 C723 C705 C706 C708 C716 C721 C707 C713 C720 C737 C734 C733 C718 C712 C709 C719 C717 C703 C702 C714 C722 R718 R719 R720 C738 X701 . ELEC 4.3UF 50V 5X11 85 / CAP.CER.25W SOT2 IC 74HC4053D IC AN5832SA RES SMD 10 OHM 1/10W +/-5% RES SMD 100 OHM 1/10W 0603 RES SMD 100 OHM 1/10W 0603 RES SMD 10K OHM 1/10W 0603 RES SMD 10K OHM 1/10W 0603 SMD. RES 100K OHM 1/10W 0603 RES SMD 180K OHM 1/10W +/-5% 0603 SMD RES 3. ELEC 2.SMD 100N0F 50V DCV 0603 CAP.0V 0603 CAP. RES 100K OHM 1/10W 0603 SMD.7 UF 50V +/-20% CAP.CER.33UF 16VDC +80%/-20% SMD. 100 OHM 1/6W +/-5% RES.SMD 75VV 250MA_A 715MVV 4N 0.F. 1K OHM 1/6W +/-5% RES. 1K OHM 1/6W +/-5% P701 C711 D701 D301 D401 D454 D404 D316 D315 D207 D206 D210 D406 D601 D412 D204 D205 D101 D201 D202 D203 D411 Q402 Q601 Q403 Q901 Q210 Q602 Q401 IC202(CP) IC601 IC301 R239 R215 R214 R208 R102 R101 R241 R246 R250 R604A R603A R272 R256 R240 R228 R213 R302 R303 R258 R257 R415 R254 R255 R614 R242 . C. 100 OHM 1/6W +/-5% RES. 1K OHM 1/6W +/-5% RES. 100 OHM 1/6W +/-5% RES. C.F.T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-DM63SAE-BT1 T8-BM62SAE-MA3SM T8-BM62SAE-MA3HM T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 40-00NX56-BTE2XG 46-40362W-16XG 25-BCB101-M1X 09-BAS316-ATX T8-BM62SAE-MA3HM T8-NX56LA-MA11 10-0FR104-FBX 10-0FR104-FBX 10-0FR104-FBX 10-0FR104-FBX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-1N4148-ABX 10-79C33V-DBX 10-79C4V7-DBX 10-79C4V7-DBX 10-79C4V7-DBX 10-79C7V5-DBX 11-DD1556-0AX 11-SA1015-YBX 11-SA1015-YBX 11-SC1815-YBX 11-SC1815-YBX 11-SC1815-YBX 11-SD667A-CBX 13-00M24C-16P 13-DA7266-SAS 13-STV817-2AS 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0101-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX TV PCB BT BD R=Y CONN 250单打 16 MALE ST R=N CAP. C.F.F. 1K OHM 1/6W +/-5% RES. 100 OHM 1/6W +/-5% RES. 100 OHM 1/6W +/-5% RES. C.F.4W SOD323 ASS'Y .F.4W 80MHZ TO-92 2SC TRANSISTOR 2SD667A-C IC-EEPROM M24C16-WBN6 R=N TCL13-DA7266-SAS= IC TDA7266SA R=N IC-DEFLECT STV8172A VERTICAL DEFLECTION RES. 100 OHM 1/6W +/-5% RES.F.4W 80MHZ TO-92 2SC TR 50VV 150MA_A NPN 0.MAIN BDKIT ASS'Y . 1K OHM 1/6W +/-5% RES. C.F.F. C. C.F. 1K OHM 1/6W +/-5% RES. C. 100 OHM 1/6W +/-5% RES.F. C.F. C. 100 OHM 1/6W +/-5% RES. C.F. C. C. C.4W 80MHZ TO-92 ST2 TR 50VV 150MA_A PNP 0. C. C. 100 OHM 1/6W +/-5% RES. C. C.F. C.7V BZX79C4V7 D-PR /A /_V 4.F. 1K OHM 1/6W +/-5% RES. C. 1K OHM 1/6W +/-5% RES. C. 1K OHM 1/6W +/-5% RES. 100 OHM 1/6W +/-5% RES.F. 100 OHM 1/6W +/-5% RES.7V BZX79C4V7 TCL10-79C7V5-DBX= DIODE ZENER 7V5 1/2W 5 TRANSISTOR 3DD1556 TR 50VV 150MA_A PNP 0.MAIN BDEQU DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) DIODE ZENER 33V 1/2W 5% D-PR /A /_V 4.ELE 5MM 100UF 16VV 5X11 85 / D. C. 1K OHM 1/6W +/-5% RES.F.F. 100 OHM 1/6W +/-5% RES. C.F.F. 100 OHM 1/6W +/-5% RES.F.7V BZX79C4V7 D-PR /A /_V 4. 100 OHM 1/6W +/-5% RES. 1K OHM 1/6W +/-5% RES.F. C.F.F.F.4W 80MHZ TO-92 2SC TR 50VV 150MA_A NPN 0. C.4W 80MHZ TO-92 ST2 TR 50VV 150MA_A NPN 0. 56K OHM 1/6W +/-5% RES. 47 OHM 1/6W +/-5% RES. C.F. C.F. C. 10K OHM 1/6W +/-5% RES. 22K OHM 1/6W +/-5% RES. 10K OHM 1/6W +/-5% RES.F.F. C.F. 2. C.F.F. 82 OHM 1/6W +/-5% RES. 18K OHM 1/6W +/-5% RES. C.F.F. 1. 680 OHM 1/6W +/-5% RES.F. C.F.F.F. C. 470 OHM 1/6W +/-5% RES. 39K OHM 1/6W +/-5% RES.2K OHM 1/6W +/-5% RES. C.F.F. 4.F. 1K OHM 1/6W +/-5% RES.T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 18-CB0102-JNX 18-CB0102-JNX 18-CB0102-JNX 18-CB0103-JNX 18-CB0103-JNX 18-CB0103-JNX 18-CB0103-JNX 18-CB0103-JNX 18-CB0103-JNX 18-CB0104-JNX 18-CB0123-JNX 18-CB0152-JNX 18-CB0153-JNX 18-CB0183-JNX 18-CB0202-JNX 18-CB0222-JNX 18-CB0222-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0223-JNX 18-CB0333-JNX 18-CB0333-JNX 18-CB0391-JNX 18-CB0563-JNX 18-CB0393-JNX 18-CB0470-JNX 18-CB0470-JNX 18-CB0470-JNX 18-CB0471-JNX 18-CB0471-JNX 18-CB0471-JNX 18-CB0472-JNX 18-CB0472-JNX 18-CB0472-JNX 18-CB0472-JNX 18-CB0473-JNX 18-CB0274-JNX 18-CB0513-JNX 18-CB0562-JNX 18-CB0562-JNX 18-CB0680-JNX 18-CB0681-JNX 18-CB0820-JNX 18-CB0820-JNX 18-CB0820-JNX 18-CB0820-JNX 18-CD0100-JNX 18-CD0121-JNX 18-CD0189-JNX 18-EE0478-JNX 18-EE0478-JNX 25-BCB101-M1X 25-BCB101-M1X 25-BCB101-M1X 25-BCB101-M1X RES. 22K OHM 1/6W +/-5% RES. C. 4. 22K OHM 1/6W +/-5% RES. C.F. C. C.F. C. 47K OHM 1/6W +/-5% TCL18-CB0274-JNX= RES. 12K OHM 1/6W +/-5% RES.F. C. C.F.ELE 5MM 100UF 16VV 5X11 85 / CAP.F. 10K OHM 1/6W +/-5% RES. C. C. 4. 270K OHM 1/6 TCL18-CB0513-JNX= RES. C.47 OHM 1/2W +/-5% CAP.ELE 5MM 100UF 16VV 5X11 85 / R271 R923 R409 R421 R238 R613 R612 R610 R428 R417 R216 R251 R201 R926 R407 R301 R304 R406 R905 R611 R902 R903 R249 R906 R332 R209 R210 R204 R607 R212 R220 R223 R224 R401 R202 R924 R231 R219 R229 R270 R206 R410 R925 R605 R606 R203 R207 R901 R269 R904 R278 J410 R403 R305 R418 R408 C219 C252 C253 C243 . C. C. C. C.F. 470 OHM 1/6W +/-5% CARBON RES. C. C. C. C. 22K OHM 1/6W +/-5% RES. 47 OHM 1/6W +/-5% RES.F.F.F.F.F. 33K OHM 1/6W +/-5% RES.5K OHM 1/6W +/-5% RES. 2.F. 10 OHM 1/4W +/-5% RES.F. C.F. C. C. C.F. C. 82 OHM 1/6W +/-5% RES. C.F.F.8 OHM 1/4W +/-5% RES. C.F. 22K OHM 1/6W +/-5% RES.7K OHM 1/6W +/-5% CARBON RES.6K OHM 1/6W +/-5% RES. 120 OHM 1/4W +/-5% RES. C.F. 390 OHM 1/6W +/-5% RES. C.7K OHM 1/6W +/-5% CARBON RES.F. C. 100K OHM 1/6W +/-5% RES.F. 1K OHM 1/6W +/-5% RES.F.F. 4. 22K OHM 1/6W +/-5% RES.F.6K OHM 1/6W +/-5% RES.F. 82 OHM 1/6W +/-5% RES. 47 OHM 1/6W +/-5% RES. C. 10K OHM 1/6W +/-5% RES. 22K OHM 1/6W +/-5% RES.F.F 1. 10K OHM 1/6W +/-5% RES.F.F. 68 OHM 1/6W +/-5% RES. 1K OHM 1/6W +/-5% RES. 82 OHM 1/6W +/-5% RES.47 OHM 1/2W +/-5% RES.F. 22K OHM 1/6W +/-5% RES. C. C.F.ELE 5MM 100UF 16VV 5X11 85 / CAP. 15K OHM 1/6W +/-5% RES. C. 10K OHM 1/6W +/-5% RES.7K OHM 1/6W +/-5% CARBON RES. 5. C.ELE 5MM 100UF 16VV 5X11 85 / CAP.F. C. 5.F. C. 33K OHM 1/6W +/-5% RES. 51K OHM 1/6W RES. C. C.F. C. 2K OHM 1/6W +/-5% RES.2K OHM 1/6W +/-5% RES. C. C.F. FUS 0. C.7K OHM 1/6W +/-5% RES. FUS 0. C. C. 470 OHM 1/6W +/-5% RES. C.F.F. C.F. T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 25-BFB100-M1X 25-BDB470-M1X 25-BDB470-M1X 25-BDB102-M1X 25-BDB102-M1X 25-BDB470-M1X 25-BDB471-M1X 25-BEB101-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BFB109-M1X 25-BDB470-M1X 25-BFB479-M1X 25-BJG101-M1X 25-DFA479-M1XR 26-AIC391-KBX 26-EBP102-KBS 26-EBP102-KBS 26-EBP102-KBS 26-EBP102-KBS 26-EBP103-ZFS 26-EBP103-ZFS 26-EBP103-ZFS 26-EBP103-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP223-ZFS 26-EBP223-ZFS CAP. ELEC 10 UF 50V +/-20% CAP.ELE 5MM 47UF 25VV 5X11 85 / CAP.ELE 5MM 47UF 25VV 5X11 85 / CAP.ELE 5MM 1000UF 25V 10*20 85 CD110 CAP.ELE 5MM 1000UF 25V 10*20 85 CD110 CAP.ELE 5MM 47UF 25VV 5X11 85 / CAP. ELEC 470 UF 25V +/-20% CAP. ELEC 100 UF 35V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 10 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP. ELEC 1 UF 50V +/-20% CAP.ELE 5MM 47UF 25VV 5X11 85 / CAP. ELEC 4.7 UF 50V +/-20% CAP. ELEC 100 UF 160V +/-20% CAP.ELEC 4.7UF 50V +/-20% CAP. CER 390 PF 500V +/-10% B CAP.CER 1NF 50V - +/-10% B% CAP.CER 1NF 50V - +/-10% B% CAP.CER 1NF 50V - +/-10% B% CAP.CER 1NF 50V - +/-10% B% CAP.CER 10NF 50V +80% -20% CAP.CER 10NF 50V +80% -20% CAP.CER 10NF 50V +80% -20% CAP.CER 10NF 50V +80% -20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 0.1UF 50V +80%/-20% CAP. CER 22NF 50V +80%/-20% CAP. CER 22NF 50V +80%/-20% C237 C104 C605 C305 C303 C402 C601 C307 C221 C902 C211 C203 C202 C230 C101 C106 C250 C609 C251 C249 C248 C247 C246 C245 C226 C216 C425 C205 C419 C452 C412 C306 C301 C213 C212 C108 C207 C218 C311 C105 C107 C239 C238 C235 C244 C217 C304 C611 C240 C241 C210 C233 C302 C901 C242 C608 C220 C222 C225 C206 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 26-EBP333-KBS 26-EBP333-KBS 27-MBC104-J0X 27-MBC104-J0X 27-MBC104-J0X 27-MBC154-J0X 27-MBC224-J0X 27-MBC224-J0X 27-MBC224-J0X 27-PBC563-J0X 27-PBC563-J0X 27-PBC682-J0X 34-A100K0-1IX 34-A100K0-1IX 34-A100K0-1IX 34-A100K0-1IX 34-A100K0-1IX 34-R100J2-0EX 34-R100J2-0EX 36-HDR020-XX0 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0060-B00 41-WJ0060-B00 41-WJ0060-B00 41-WJ0060-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0075-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0090-B00 41-WJ0090-B00 CAP.CER 33NF 50V +/-10% CAP.CER 33NF 50V +/-10% CAP. M.P.E 0.1 UF 63V +/-5% CAP. M.P.E 0.1 UF 63V +/-5% CAP. M.P.E 0.1 UF 63V +/-5% CAP. M.P.E. 0.15UF 63V +/-5% CAP. M.P.E 0.22UF 63V +/-5% CAP. M.P.E 0.22UF 63V +/-5% CAP. M.P.E 0.22UF 63V +/-5% CAP. P.E 0.056 UF 63V +/-5% CAP. P.E 0.056 UF 63V +/-5% CAP. P.E 0.0068UF 63V +/-5% COIL CHOKE 10 UH +/-10% COIL CHOKE 10 UH +/-10% COIL CHOKE 10 UH +/-10% COIL CHOKE 10 UH +/-10% COIL CHOKE 10 UH +/-10% COIL PL - 10 UH +/-5% COIL PL - 10 UH +/-5% TRANSFORMER HORIZ DRIVE BCT-1621 TCL41-WJ0050-B00= WIRE BARE JUMPER TCL41-WJ0050-B00= WIRE BARE JUMPER TCL41-WJ0050-B00= WIRE BARE JUMPER TCL41-WJ0050-B00= WIRE BARE JUMPER WIRE-BARE WIRE-BARE WIRE-BARE WIRE-BARE WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER8.5MM WIREBAREJUMPER8.5MM WIREBAREJUMPER8.5MM WIREBAREJUMPER8.5MM WIREBAREJUMPER8.5MM WIREBAREJUMPER8.5MM WIREBAREJUMPER9MM WIREBAREJUMPER9MM 5MM 5MM 5MM 5MM R R R R C612 C613 C309 C214 C204 C208 C602 C603 C310 C414 C420 C215 L204 L202 L101 L203 L201 L205 L206 T402 J417 J416 J415 J412 J609 J910 J244 J202 J907 J222 J411 J235 J242 J902 J223 J307 J303 J301 JB601 JB602 J212 J610 J605 J409 J311 J102 J107 J231 J229 J227 J243 J208 J309 J214 J602 J228 J310 J305 JB603 JB604 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 41-WJ0090-B00 41-WJ0090-B00 41-WJ0095-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0105-B00 41-WJ0110-B00 41-WJ0110-B00 41-WJ0115-B00 41-WJ0115-B00 41-WJ0115-B00 41-WJ0115-B00 41-WJ0115-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0125-B00 41-WJ0150-B00 41-WJ0150-B00 41-WJ0150-B00 41-WJ0150-B00 41-WJ0175-B00 41-WJ0175-B00 41-WJ0175-B00 41-WJ0200-B00 45-OSC24M-5N6BR 46-33079W-02XG 46-33079W-03XG 46-33079W-04XG 46-39402W-04XG 63-B30100-AB4G 64-P30080-104G 64-P30080-104G 63-B30080-BT4G 66-343730-0B0 66-343730-0B0 66-343730-0B0 66-343740-0B0 67-H27292-1A0 WIREBAREJUMPER9MM WIREBAREJUMPER9MM WIREBAREJUMPER9.5MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10.5MM WIREBAREJUMPER11MM WIREBAREJUMPER11MM WIREBAREJUMPER11.5MM WIREBAREJUMPER11.5MM WIREBAREJUMPER11.5MM WIREBAREJUMPER11.5MM WIREBAREJUMPER11.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER12.5MM WIREBAREJUMPER15MM WIREBAREJUMPER15MM WIREBAREJUMPER15MM WIREBAREJUMPER15MM WIREBAREJUMPER17.5MM WIREBAREJUMPER17.5MM WIREBAREJUMPER17.5MM WIREBAREJUMPER20MM CRYSTAL 24.576MHZ 30PPM R=Y PIN BASE *2 TJC3-2A PIN BASE *3 TJC3-3A PIN BASE *4 TJC3-4A BASE SCREW-ST 3MM 10MM JIS B 1122 53 0 0 R=Y M/C SCREW P 3 X 8 M/C SCREW P 3 X 8 S/T SCREW B 3 X 8 BT HOLLOW RIVET 1.6MMX3.0MMX3.2MM HOLLOW RIVET 1.6MMX3.0MMX3.2MM HOLLOW RIVET 1.6MMX3.0MMX3.2MM HOLLOW RIVET (2.3MMX4.0MMX3.5MM) HEAT SINK J234 J221 J403 J225 J230 J105 J104 J205 J206 J308 J414 J109 J110 J607 J606 J237 J238 J601 J101 J201 J220 J413 J407 J908 J216 J215 J219 J217 J218 J608 J404 J203 J240 J241 J304 J210 J204 J906 J211 J006 J224 J918 J406 J408 J402 J405 X201 P602 P603 P203 P401 FOR IC301 FOR IC601 FOR Q451 FOR Q402 FOR L451 FOR Q402 FOR L458 FOR P401 Y451 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 67-H30752-GA0 67-H40390-4A0 67-H40390-4A0 67-M40068-2E4 10-79C5V6-DBX 62-227680-0UA 62-227680-1UA 41-WJ0060-B00 41-WJ0050-B00 26-ABC103-ZFX 18-CB0332-JNX 18-CB0332-JNX 25-BLB100-M1X 41-WJ0100-B00 18-CB0272-JNX 11-KTD863-0BX 11-KTD863-0BX 11-SC1815-YBX 26-EBP103-ZFS 11-SC1815-YBX 26-EBP470-JCS 11-SC1815-YBX 26-EBP470-JCS 18-CB0100-JNX 18-CB0101-JNX 26-EBP103-ZFS 18-CB0101-JNX 25-BFB220-M1X 25-BFB479-M1X 25-BFB220-M1X 18-CB0102-JNX 27-PBC103-J0X 18-CB0391-JNX 25-BFB100-M1X 18-CB0331-JNX 18-FG0180-JSX 41-WJ0075-B00 18-CB0101-JNX 10-79C5V6-DBX 10-1N4148-ABX 18-CB0152-JNX 10-79C4V7-DBX 18-CB0221-JNX 18-CB0103-JNX 10-79C18V-DBX 18-CB0562-JNX 10-0FR104-FBX 18-CB0102-JNX 66-343730-0B0 18-CB0102-JNX 18-FF0399-JSX 41-WJ0100-B00 18-CB0393-JNX 41-WJ0100-B00 18-CB0471-JNX 18-CB0102-JNX 18-CB0102-JNX 41-WJ0080-B00 41-WJ0065-B00 41-WJ0100-B00 RAW HEATSINK -- GA0 00 R=N HEAT SINK HEAT SINK TV RAW SUPPORT -- -- 00 00 00 R=N DIODE ZENER 5V6 1/2W 5% TV RAW SUPPORT CABLE CHASSIS -- 00 00 00 TV RAW SUPPORT CABLE FBT -- 01 00 00 R=N WIRE-BARE TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R CAP. CER 0.01 UF 50V +80-20% F RES. C.F. 3.3K OHM 1/6W +/-5% RES. C.F. 3.3K OHM 1/6W +/-5% CAP. ELEC 10 UF 250V +/-20% WIREBAREJUMPER10MM RES. C.F. 2.7K OHM 1/6W +/-5% TRANSISTOR KTD863 TRANSISTOR KTD863 TR 50VV 150MA_A NPN 0.4W 80MHZ TO-92 2SC CAP.CER 10NF 50V +80% -20% TR 50VV 150MA_A NPN 0.4W 80MHZ TO-92 2SC CAP. CER 47 PF 50V +/-5% TR 50VV 150MA_A NPN 0.4W 80MHZ TO-92 2SC CAP. CER 47 PF 50V +/-5% RES. C.F. 10 OHM 1/6W +/-5% RES. C.F. 100 OHM 1/6W +/-5% CAP.CER 10NF 50V +80% -20% RES. C.F. 100 OHM 1/6W +/-5% CAP. ELEC 22 UF 50V +/-20% CAP. ELEC 4.7 UF 50V +/-20% CAP. ELEC 22 UF 50V +/-20% RES. C.F. 1K OHM 1/6W +/-5% CAP. P.E. 0.01UF 63V +/-5% RES. C.F. 390 OHM 1/6W +/-5% CAP. ELEC 10 UF 50V +/-20% RES. C.F. 330 OHM 1/6W +/-5% RMOF 18OHM +/-5% 2W R=Y WIREBAREJUMPER7.5MM RES. C.F. 100 OHM 1/6W +/-5% DIODE ZENER 5V6 1/2W 5% DIODE 1N4148 (SWITCHING) RES. C.F. 1.5K OHM 1/6W +/-5% D-PR /A /_V 4.7V BZX79C4V7 RES. C.F. 220 OHM 1/6W +/-5% RES. C.F. 10K OHM 1/6W +/-5% D-PR /A /_V 18V BZX79C18 RES. C.F. 5.6K OHM 1/6W +/-5% DIODE FR104 (FAST RECTIFIER) RES. C.F. 1K OHM 1/6W +/-5% HOLLOW RIVET 1.6MMX3.0MMX3.2MM RES. C.F. 1K OHM 1/6W +/-5% RMOF 3.9OHM +/-5% 1W R=Y WIREBAREJUMPER10MM RES. C.F. 39K OHM 1/6W +/-5% WIREBAREJUMPER10MM RES. C.F. 470 OHM 1/6W +/-5% RES. C.F. 1K OHM 1/6W +/-5% RES. C.F. 1K OHM 1/6W +/-5% WIREBAREJUMPER8MM 1 R=N WIREBAREJUMPER10MM Y402 Y1 Y2 Y301 D004 JP103 JP202 C209 R221 R222 C413 R004 R211 Q201 Q202 Q301 C256 Q903 C102 Q904 C103 R217 R245 C257 R247 C317 C318 C319 R253 C401 R259 C421 R260 R262 D220 R274 D251 D313 R311 D314 R314 R315 D408 R316 D410 R423 FOR T401 R429 R460 J001 R608 J002 R921 R927 R928 J007 J008 J108 4W 80MHZ TO-92 2SC TRANSISTOR 2SK2996 (MOS) IC-REGSPECKT TL431ACLP R=N OPTICOUP NCP1337P TCL13-PC123X-9YP= PHOTOCOUPLER PC123X9YF RES.05 00 R=N WIREBAREJUMPER10MM WIREBAREJUMPER18.F.5MM WIREBAREJUMPER8.CER 10NF 50V +80% -20% CAP.5MM WIREBAREJUMPER7.5MM WIREBAREJUMPER12MM WIREBAREJUMPER5. C.F.1V 1_A 1000V / /W DO-41 1N4007 DIODE 1N4148 (SWITCHING) D-PR /A /_V 3.F. 1K OHM 1/6W +/-5% Y601 J207 J213 J226 J232 J245 J246 J247 J248 J249 J419 J420 J421 J423 J424 J425 J426 J427 J904 J905 J911 J913 J914 J915 J916 J917 JZ903 R252 R275 R922 D407 C308 D455 Q451 J233 D250 R261 R205 C005 C002 D813 D811 D810 D804 D809 D802 D807 ZD803 ZD802 D803 ZD801 Q808 Q806 Q801 IC802 IC801 IC803 R852 .5MM WIREBAREJUMPER17MM WIREBAREJUMPER10MM WIREBAREJUMPER8.5MM WIREBAREJUMPER10MM WIREBAREJUMPER5. C. 1K OHM 1/6W +/-5% RES.3V 1_A 1000VV 500NS /W DO-15 FR1 D-PIN 1.2 OHM 1/2W D-PR /A /_V 9. C. CER 220 PF 50V +/-5% TV PCB MA BD R=Y ASS'Y .5MM WIREBAREJUMPER8.9V BZX79C3V9 DIODE HER108 DIODE 500MW 16HSC TRANSISTOR DTC144ESA TR 50VV 150MA_A NPN 0. C.5MM WIREBAREJUMPER11.2V 500MI0W R=N CAP. C. 100 OHM 1/6W +/-5% RES.5MM WIREBAREJUMPER5.F.1V BZX79C9V1 RMOF 18OHM +/-5% 2W R=Y RES.POWER PARTSASYKIT DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) D-PIN 1.F.5A R=Y N-CHANNEL MOSFET IRFS630B TCL18-CE0229-JNX= RES.5MM RES.9V BZX79C3V9 D-PR /A /_V 3. 10K OHM 1/6W +/-5% CAP. CER 220 PF 50V +/-5% D-FSR GBY228 1500V 2. 470 OHM 1/6W +/-5% D-ZENER BZX55C8V2 8.T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-NX56LA-MA11 T8-BM62SAE-MA3HM T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 67-H82981-7A0 41-WJ0100-B00 41-WJ0185-B00 41-WJ0100-B00 41-WJ0055-B00 41-WJ0075-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0065-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0055-B00 41-WJ0075-B00 41-WJ0055-B00 41-WJ0085-B00 41-WJ0170-B00 41-WJ0100-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0085-B00 41-WJ0115-B00 41-WJ0120-B00 41-WJ0055-B00 18-CB0102-JNX 18-CB0101-JNX 18-CB0471-JNX 10-79C8V2-DBX 26-EBP221-JCS 10-GBY228-FPX 11-RFS630-0CXB 18-CE0229-JNX 10-79C9V1-DBX 18-FG0180-JSX 18-CB0103-JNX 26-EBP103-ZFS 26-EBP221-JCS 40-00NX56-MAO1XG T8-NX56LA-PW7 10-0FR104-FBX 10-0FR104-FBX 10-0FR104-FBX 10-0FR104-FBX 10-0FR107-FBX 10-1N4007-EBX 10-1N4148-ABX 10-79C3V9-DBX 10-79C3V9-DBX 10-HER108-FBX 10-HS16VC-DBX 11-TC144E-0BX 11-SC1815-YBX 11-SK2996-0AX 13-000TL4-31T 13-NCP133-7PP 13-PC123X-9YP 18-CB0102-JNX RAW HEATSINK -.5MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM 1 R=N TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R WIREBAREJUMPER5.5MM WIREBAREJUMPER7. 2. C.5MM WIREBAREJUMPER8.F. F.ELE 5MM 47UF 25VV 5X11 85 / CAP.1UF 50V +80%/-20% CAP. GLASS GLAZE 1M OHM 1/2W +/-5% RES.F.CER 470P0F 1KVV CAP. 10K OHM 1/6W +/-5% RES.F. M. 2. CER 4700 pF 1KV +/-20% CAP.5X25 85 / CAP.1UF 50V +80%/-20% CAP.ELE 5MM 1000UF 25V 10*20 85 CD110 CAP. M. GLASS GLAZE 4.F.E 0. C. CER 0. CER 0.F.T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 18-CB0102-JNX 18-CB0103-JNX 18-CB0153-JNX 18-CB0183-JNX 18-CB0122-JNX 18-CB0222-JNX 18-CB0331-JNX 18-CD0100-JNX 18-CD0101-JNX 18-DD0184-FNX 18-DB0103-FNX 18-DB0223-FNX 18-DB0393-FNX 18-FE0102-JNX 18-FG0223-JSX 18-FH0473-JLX 18-KE0105-JNX 18-KE0475-JNX 18-KF0825-JH3 18-MJ0108-JDX 22-NTC479-XX0 22-PTC909-3A5 25-BCB101-M1X 25-BCB101-M1X 25-BCB102-M1X 25-BDB470-M1X 25-BDA222-M1S 25-BDB102-M1X 25-BDB102-M1X 25-BDB470-M1X 25-BFB100-M1X 25-BFB100-M1X 25-BJG331-M1X 25-BMJ221-M1S 26-AIC103-MEX 26-AIC103-MEX 26-AKC331-KBX 26-AKC471-KRX 26-AKC472-MEX 26-AKC472-MEX 26-AKL103-MFX 26-APL222-MEX 26-APL471-KBX 26-APL471-KBX 26-EBP102-KBS 26-EBP102-KBS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 26-EBP104-ZFS 27-AQT474-MV3 27-MHW104-K0X 35-392170-0IX 35-392170-0IX 36-LIF005-XX1 36-LIF087-JX1 41-WJ0050-B00 RES. C. ELEC 10 UF 50V +/-20% CAP. M.ELE 5MM 2200UF 25VV 12.7D2-14 PTC MZ73BHL-9Ω±20% CAP.2K OHM 1/6W +/-5% RES.VOLT.1UF 50V +80%/-20% CAP. C.7M OHM 1/2W +/-5% RES. M. CER 0.1UF 50V +80%/-20% CAP.ELE 5MM 100UF 16VV 5X11 85 / CAP. 39K OHM 1/6W +/-1% RESISTOR METAL OXIDE FILM 1K0OHM 5% 1/2W RMOF 2W +-5%22KΩ RESISTOR METAL OXIDE FILM 47K0OHM 5% 3WW RES. CER 470PF 400VAC +/-10% B CAP.PP0. CER 4700 pF 1KV +/-20% CAP.CER 1NF 50V .CER 330P0F 1K0V CAP.F.F. 100 OHM 1/4W +/-5% RES. C.ELE 10MM 200UF 400V 30*30 85 \ CC 10NF +20% 500V E CC 10NF +20% 500V E CAP. CER 0. CER 0. 10K OHM 1/6W TCL18-DB0223-FNX= RES.47UF275VAC+/-20% CAP. 1K OHM 1/6W +/-5% RES. 10 OHM 1/4W +/-5% RES.1UF 50V +80%/-20% CAP. M. C.1UF 50V +80%/-20% CAP.F. 1. 330 OHM 1/6W +/-5% RES.1 UF 400V +/-10% FERR BEAD BF-I35050R-730 FERR BEAD BF-I35050R-730 LINE FILTER LCL-2826A LINE FILTER LGH2V-40UH TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R R844 R808 R810 R831 R805 R820 R819 R840 R809 R829 R830 R803 R832 R804 R837 R812 R839 R801 R838 R806 RT802 RT801 C844 C842 C833 C850 C832 C829 C827 C812 C816 C861 C824 C803 C804 C825 C817 C805 C801 C802 C809 CY803 CY801 CY802 C814 C838 C831 C830 C828 C813 C839 C851 C834 CX802 C810 L802 L804 LF802 LF801 J826 .CER 1NF 50V .F.ELE 5MM 47UF 25VV 5X11 85 / CAP.F.F. C.+/-10% B% CAP.F.ELE 5MM 100UF 16VV 5X11 85 / CAP.P. CER 2200PF 400VAC+/-20% E CAP. C. C. ELEC 330 UF 160V +/-20% (18X40) CAP. ELEC 10 UF 50V +/-20% CAP.1UF 50V +80%/-20% CAP.ELE 5MM 1000UF 25V 10*20 85 CD110 CAP. CER 470PF 400VAC +/-10% B CAP. CER 0. 18K OHM 1/6W +/-5% RES.CC 8.2K OHM 1/6W +/-5% RES. 22K OHM 1/6W RES. CER 10 NF 1KVDC +/-20% CAP. CER 0.ELE 5MM 1000UF 16V 10X16 85 / CAP.+/-10% B% CAP. 180K OHM 1/4W +/-1% TCL18-DB0103-FNX= RES.F.2M OHM 1W +/-5% RESISTOR CEMENTED 0R1OHM 5% 5WW NTC 4. 15K OHM 1/6W +/-5% RES. C.M. H. 47 OHM 1/6W +/-5% TCL26-EBP473-ZFS= CAP.0MMX3. CER 680 PF 50V +/-5% CARBON RES. CEP 560PF 50V +/-5% CAP.7K OHM 1/6W +/-5% RES. CER 47NF 50V +80/ TRANSFORMER BCK-4216 WIREBAREJUMPER7.2MM WIREBAREJUMPER7.6MMX3.ELE 5MM 47UF 25VV 5X11 85 / DIODE 1N4148 (SWITCHING) DIODE 1N4148 (SWITCHING) HOLLOW RIVET 1.0MMX3. C.3K OHM 1/2W +/-5% CAP.5MM) RAW HEATSINK -.5MM PIN BASE *2 TJC2-2A FUSE T4AL/250V M/C SCREW P 3 X 8 FUSE HOLDER HOLLOW RIVET (2.01 00 R=Y LABEL WIREBAREJUMPER12.5MM WIREBAREJUMPER10MM WIREBAREJUMPER10MM WIREBAREJUMPER12.5MM WIREBAREJUMPER10MM J827 J828 J829 J818 J832 J830 J831 J835 J836 J834 J823 J821 J819 J833 J824 J813 J806 J807 J825 J814 J810 J809 J802 J801 J820 CN802 F801 FOR Q801 FOR F801 FOR C803 Y801 FOR Y801 J811 CN803 FOR CN803 R841 C822 C815 R851 R811 C806 T801 C823 C807 C843A C847 D814 D815 FOR C824 FOR T801 J822 J837 J839 J840 J841 J842 J843 J844 J845 JP807 .5MM WIREBAREJUMPER9.5MM WIREBAREJUMPER9.F.5MM TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R WIREBAREJUMPER5. 4.6MMX3.5MM PIN BASE *3 VH-3A HOLLOW RIVET (2.5MM WIREBAREJUMPER8.2MM HOLLOW RIVET 1.5MM CAP. C.0MMX3. C.3MMX4.0MMX3.F.ELE 5MM 47UF 25VV 5X11 85 / CAP.CER 220P0F 500VV CAP.3MMX4.5MM) RES.F. 3.T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0075-B00 41-WJ0095-B00 41-WJ0095-B00 41-WJ0100-B00 41-WJ0100-B00 41-WJ0125-B00 46-10962W-02XG 50-04000D-1GS1G 64-P30080-104G 66-20517X-0B7 66-343740-0B0 67-H38012-VA0 71-DYP000-WX1 41-WJ0125-B00 46-35063W-03XG 66-343740-0B0 18-CE0332-JNX 26-AIC221-KBX 26-EBP681-JCS 18-CB0472-JNX 18-CB0470-JNX 26-EBP473-ZFS 36-TRF325-AX1 41-WJ0075-B00 26-EBP561-JCS 25-BDB470-M1X 25-BDB470-M1X 10-1N4148-ABX 10-1N4148-ABX 66-343730-0B0 66-343730-0B0 41-WJ0075-B00 41-WJ0085-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0055-B00 41-WJ0100-B00 TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM R WIREBAREJUMPER7. CER 1500 pF 1KV +/-10% CAP.F.F. 4.5MM ASS'Y .O.ELE 5MM 47UF 25VV 5X11 85 / D-ZENER BZX55C8V2 8.0W 1. 820 OHM 1/6W +/-5% RMOF 5.5MM ASS'Y .75MHZ D1539C IC MCU(WRITE) SERVICE CARD LABEL HEAT SINK DSTG-1 PIN BASE *4 TJC3-4A PIN BASE *2 TJC3-2A PIN BASE *5 TJC3-5A POWER CORD 2200MM Y B05899 FR 1OHM 1/2W 立式编带 ≤30S N RF10S WIRE UL1007 300MM 4 WIRE CRT板 RGB 6排线 450MM 6 TJC3 SCN 2.M.CER 220P0F 500VV CAP.625W 100MHZ TO-92 2N TRANSISTOR KTD863 TR 50VV 150MA_A PNP 0.5A R=Y D-FSR GRU4YX 100V 4A R=Y CAP.F 1. C.6OHM +/-5% 2W R=Y CARBON RES.ELE 5MM 47UF 100V 10*16 85 B41827系 D-PR /A /_V 18V BZX79C18 D-FSR 1N5407 800V 3A R=Y D-FSR 1N5407 800V 3A R=Y D-FSR 1N5407 800V 3A R=Y D-FSR 1N5407 800V 3A R=Y D-FSR RU4C 1000V 2.CER 10NF 50V +80% -20% RESISTOR 线绕电阻 0.ELE 5MM 47UF 25VV 5X11 85 / CAP.'+' TO C847 '-' DB804 DB803 DB802 DB801 D808 D812 C826 ZD805 JE901 JE902 JE903 JE904 JE905 P901 JE906 TU101 Z201 IC201(CP) FOR PRODUCTION USE R R R R R P202(PIN1-PIN4) P204 P902 R465 RED-A/BLUE-C/GREENB/YELLOW-D P201 S402 D410 D411 .AV PARTSKIT TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM TCL41-WJ0050-B00= WIRE BARE JUMPER 5MM SOCKET-RCA 9 RD-BU-GN-RD-WH-YW R WIREBAREJUMPER7.5MM CAP.F. C.0W 220 OHM +/-5% RESISTOR 金属氧化膜 68OHM +/-5% 1W RS1FS RES.OTHER PARTSKIT TUNER F07GP-4ND-E SAW FILTER 45. 27K OHM 1/6W +/-5% CAP.7V BZX79C4V7 WIREBAREJUMPER7. CER 680 PF 500V +/-10% B RES.47OHM +/-5% 2W KN2W/ CAP.2V 500MI0W R=N ASS'Y . WIRE UL2468#26 400MM 4 2.7K OHM 1/6W +/-5% D-PR /A /_V 4.T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-NX56LA-PW7 T8-BM62SAE-MA3HM T8-NX56LA-AV1 T8-NX56LA-AV1 T8-NX56LA-AV1 T8-NX56LA-AV1 T8-NX56LA-AV1 T8-NX56LA-AV1 T8-NX56LA-AV1 T8-BM62SAE-MA3HM T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-OT3 T8-BM62SAE-MA3SM T8-BM63SAE-DP2 T8-BM63SAE-DP2 41-WJ0100-B00 41-WJ0100-B00 11-2N5551-CBX 11-KTD863-0BX 11-SA1015-YBX 18-FG0183-JSX 18-FF0221-JSX 18-FF0680-JSX 18-CB0821-JNX 18-FG0569-JSX 18-CB0472-JNX 10-79C4V7-DBX 41-WJ0075-B00 26-AIC221-KBX 26-AIC221-KBX 18-FE0100-JNX 26-AIC681-KBX 18-CB0273-JNX 26-AKC152-KRX 25-BDB470-M1X 26-EBP103-ZFS 18-RG0478-JSX 25-BHB470-M1X 10-79C18V-DBX 10-1N5407-FPX 10-1N5407-FPX 10-1N5407-FPX 10-1N5407-FPX 10-00RU4C-FPX 10-0RU4YX-FPX 25-BDB470-M1X 10-79C8V2-DBX T8-NX56LA-AV1 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 41-WJ0050-B00 47-RCA243-XX1G 41-WJ0075-B00 T8-BM62SAE-OT3 07-457FF5-NA9G 45-SAWD15-39C0D 13-TDA111-45P 70-271510-00A 71-270870-0A9 90-0DSTG1-SR1U 46-33079W-04XG 46-33079W-02XG 46-33079W-05XG 51-DC0220-0CN01G 18-EE0109-JSX 46-40331H-04XG 46-CD045T-06K01G 46-CD040T-04K01G T8-BM63SAE-DP2 10-0FR104-FBX 10-0FR104-FBX WIREBAREJUMPER10MM WIREBAREJUMPER10MM TR 160V 0.DPC PARTSEQU DIODE FR104 (FAST RECTIFIER) DIODE FR104 (FAST RECTIFIER) JP808 JP809 Q802 Q804 Q805 R814 R816A R817 R818 R846 R854 ZD804 J803 C819 C820 R842 C821 R853 C811A C835 C845 R845 C846 '-' TO C847'+'.CER 220P0F 500VV RESISTOR METAL OXIDE FILM 10R0OHM 5% 1/2 CAP.4W 80MHZ TO-92 ST2 RMOF 18KOHM +/-5% 2W R=Y RES.6_A NPN 0. C. C. 2.6KV +/-5% ASS'Y . M.5MM SOFTWARE SOFTWARE SOFTWARE CODE R412 R440 R411 C435 C432 L406 L407 L405 P401 K401 FOR L407 FOR L406 FOR L405 FOR C434 FOR C433 FOR C432 FOR C431 FOR P401 C434 R1001 R006 R1005 R1003 R1002 K004 K005 K006 K001 K002 K003 J1001 R1009 K007 P1003 TO M.2MM HOLLOW RIVET 1. 560 OHM 1/6W +/-5% RES. M.0MMX3.2MM HOLLOW RIVET 1.2K OHM 1/6W +/-5% TACT SWITCH WIRE UL2468#26 600MM 2 2.0MMX3.6MMX3. CHANNEL BAND SELECTOR KFC-G02 HOLLOW RIVET 1.F.0MMX3.39UF 250VA CAP.PP 0.F.5MM) CAP.PP 0. C.T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM63SAE-DP2 T8-BM62SAE-MA3SM T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 T8-BM63SAE-KE5 03-BM62SAE-CL12S 18-FG0332-JHX 18-FG0399-JHX 18-FG0399-JHX 27-AGQ394-JSX 27-AHQ154-JSX 36-WID102-XX1 36-WID153-XX1 36-WID171-XX3 40-29M76S-DPB1XG 46-39402W-04XG 48-SLI001-XX0 66-343730-0B0 66-343730-0B0 66-343730-0B0 66-343730-0B0 66-343730-0B0 66-343730-0B0 66-343730-0B0 66-343740-0B0 27-ALR912-J0X T8-BM63SAE-KE5 18-CB0471-JNX 18-CB0561-JNX 18-CB0102-JNX 18-CB0271-JNX 18-CB0331-JNX 40-N29M71-KEG1XG 48-TAC002-XX0 48-TAC002-XX0 48-TAC002-XX0 48-TAC002-XX0 48-TAC002-XX0 48-TAC002-XX0 41-WJ0075-B00 18-CB0222-JNX 48-TAC002-XX0 46-CE060T-02K01G V8-NX56BLATM4V508 RESISTOR METAL OXIDE FILM 3K3OHM 5% 2WW RESISTOR METAL OXIDE FILM 3R9OHM 5% 2WW RESISTOR METAL OXIDE FILM 3R9OHM 5% 2WW TCL27-AGQ394-JSX= CAP.6MMX3.0MMX3.F.0MMX3.F.2MM HOLLOW RIVET 1. C.6MMX3.2MM HOLLOW RIVET (2.PP 9100 PF 1. C.6MMX3.F. 330 OHM 1/6W +/-5% TV PCB KEY BD R=Y TACT SWITCH TACT SWITCH TACT SWITCH TACT SWITCH TACT SWITCH TACT SWITCH WIREBAREJUMPER7.BD P204 IC201(CP) .5MM RES. M.0MMX3.2MM HOLLOW RIVET 1. 270 OHM 1/6W +/-5% RES. C.6MMX3.6MMX3.F.2MM HOLLOW RIVET 1.0MMX3.3MMX4. 470 OHM 1/6W +/-5% RES.0MMX3.6MMX3.KEY BDEQU RES.15UF 400V +/-5% COIL WIDTH 1 MH COIL CHOKE 15 MH COIL WIDTH L171AHA TV PCB DP BD R=Y BASE SW.2MM HOLLOW RIVET 1. 1K OHM 1/6W +/-5% RES. C.