01 General

GOLDEN ISLAND APARTMENTPhu Huu Ward, Dist.9, HCMC Electrical & Mechanical Specification Part A: General Requirements Revision Date Approved by 001 Aug 2011 NVL VHT Engineering 158 Bau Cat 3 street, Tan Binh Dist., HCMC Telephone: (84) 8 89492076 Fax: (84) 8 89492075 TABLE OF CONTENTS © VHT Engineering 2 Aug-11 Contents 0117 APPLIED STANDARDS ............................................................................................................................. 4 0171 GENERAL REQUIREMENTS ................................................................................................................ 30 1 GENERAL ................................................................................................................................................... 30 1.1 Precedence ........................................................................................................................................ 30 1.2 Cross references ................................................................................................................................ 30 1.3 Referenced documents ....................................................................................................................... 30 1.4 Interpretation .................................................................................................................................... 31 1.5 Contract documents .......................................................................................................................... 33 1.6 Performance ...................................................................................................................................... 33 1.7 Notice ................................................................................................................................................ 33 1.8 Submissions ....................................................................................................................................... 34 1.9 DESIGN ............................................................................................................................................ 36 2 PRODUCTS ................................................................................................................................................. 36 2.1 GENERAL ......................................................................................................................................... 36 2.2 Tests .................................................................................................................................................. 37 2.3 Materials and components ................................................................................................................ 37 3 EXECUTION ................................................................................................................................................ 38 3.1 Wall chasing ...................................................................................................................................... 38 3.2 Fixing ................................................................................................................................................ 38 3.3 Completion ........................................................................................................................................ 38 3.4 Record drawings ............................................................................................................................... 39 3.5 Operation and maintenance manuals ................................................................................................ 39 3.6 Cleaning ............................................................................................................................................ 41 3.7 Post-construction mandatory inspections and maintenance ............................................................. 41 181 ADHESIVES, SEALANTS AND FASTENERS ........................................................................................ 43 1 GENERAL ................................................................................................................................................... 43 1.1 Cross references ................................................................................................................................ 43 1.2 Submissions ....................................................................................................................................... 43 1.3 Inspection .......................................................................................................................................... 43 1.4 Performance ...................................................................................................................................... 43 2 PRODUCTS ................................................................................................................................................. 44 2.1 Adhesives ........................................................................................................................................... 44 2.2 Sealants ............................................................................................................................................. 44 2.3 Fasteners ........................................................................................................................................... 45 0182 FIRE-STOPPING ...................................................................................................................................... 52 1 GENERAL ................................................................................................................................................... 52 1.1 Cross references ................................................................................................................................ 52 1.2 General standards ............................................................................................................................. 52 1.3 Inspection .......................................................................................................................................... 52 1.4 Tests .................................................................................................................................................. 52 1.5 Samples ............................................................................................................................................. 52 1.6 Submissions ....................................................................................................................................... 52 PHYSICAL PERFORMANCE: SUBMIT REPORT TO AS 4072.1 APPENDIX C. ................................... 53 1 PRODUCTS ................................................................................................................................................. 53 1.1 Materials ........................................................................................................................................... 53 1.2 Components ....................................................................................................................................... 54 2 EXECUTION ................................................................................................................................................ 54 2.1 Execution generally ........................................................................................................................... 54 2.2 Systems .............................................................................................................................................. 55 2.3 Completion submissions .................................................................................................................... 56 2.4 Maintenance ...................................................................................................................................... 56 0183 METALS AND PREFINISHES ................................................................................................................ 57 1 GENERAL ................................................................................................................................................... 57 TABLE OF CONTENTS © VHT Engineering 3 Aug-11 1.1 Cross references ................................................................................................................................ 57 2 PRODUCTS ................................................................................................................................................. 57 2.1 Metals ................................................................................................................................................ 57 3 EXECUTION ................................................................................................................................................ 58 3.1 General.............................................................................................................................................. 58 3.2 Self finishing ...................................................................................................................................... 59 3.3 Electroplating .................................................................................................................................... 59 3.4 Anodising .......................................................................................................................................... 59 3.5 Metal spraying .................................................................................................................................. 59 3.6 Powder coating ................................................................................................................................. 60 THERMOSET POWDER COATING GENERALLY ...................................................................................................... 60 3.7 Prepainting ........................................................................................................................................ 61 3.8 Completion ........................................................................................................................................ 62 0186 BUILDING IT COMPONENTS ............................................................................................................... 63 1 GENERAL ................................................................................................................................................... 63 1.1 Aims ................................................................................................................................................... 63 1.2 Cross references ................................................................................................................................ 63 1.3 Submissions ....................................................................................................................................... 63 2 PRODUCTS ................................................................................................................................................. 63 2.1 Active computer hardware ................................................................................................................ 63 2.2 Software ............................................................................................................................................ 64 3 EXECUTION ................................................................................................................................................ 65 3.1 Installation ........................................................................................................................................ 65 3.2 Completion ........................................................................................................................................ 65 0223 SERVICE TRENCHING .......................................................................................................................... 66 1 GENERAL ................................................................................................................................................... 66 1.1 Cross references ................................................................................................................................ 66 1.2 Design ............................................................................................................................................... 66 1.3 Inspection .......................................................................................................................................... 66 1.4 Tests .................................................................................................................................................. 66 1.5 Submissions ....................................................................................................................................... 66 2 EXECUTION ................................................................................................................................................ 67 2.1 Excavating ......................................................................................................................................... 67 2.2 Boring ............................................................................................................................................... 67 2.3 Backfilling ......................................................................................................................................... 68 2.4 Reinstatement of surfaces .................................................................................................................. 68 GENERRAL GOLDEN ISLAND Project © VHT Engineering 4 Aug-11 0117 APPLIED STANDARDS Viet Nam 11TCN 19-84 Elec.Line - Bộ Điện Lực VN 11TCN 21-84 Power station -Bộ Điện Lực VN 11TCN 20-84 Protection - Bộ Điện Lực VN TCVN 2622:1995 Fire fighting for building TCVN 6160:1996 Fire fighting for highrise Building TCVN 5040:1980 Fire Fighting Equipment TCVN 5760:1993 Fire Fighting system-Require for design, installation and use TCXD 95:1983 Exterior Lighting TCXD 25:1991 Elec.Wiring TCXD 27:1991 Elec. Installation TCXD 46:1991 Lightning Protection Australian AS/NZS CISPR15 2006 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (CISPR 12:2000, MOD) AS 150 1980 Road tars for pavements AS ISO 354 2006 Acoustics - Measurement of sound absorption in a reverberation room AS/NZS ISO 717 Acoustics - Rating of sound insulation in buildings and of building elements AS/NZS ISO 717.1 2004 Airborne sound insulation AS ISO 717.2 2004 Impact sound insulation AS 1012 Methods of testing concrete AS 1012.1 1993 Sampling of fresh concrete AS 1012.2 1994 Preparation of concrete mixes in the laboratory AS 1012.3.1 1998 Determination of properties related to the consistency of concrete - Slump test AS 1012.3.3 1998 Determination of properties related to the consistency of concrete - Vebe test AS 1012.3.4 1998 Determination of properties related to the consistency of concrete - Compactibility index AS 1012.4.2 1999 Determination of air content of freshly mixed concrete - Measuring reduction in air pressure in chamber above concrete AS 1012.5 1999 Determination of mass per unit volume of freshly mixed concrete AS 1012.8.1 2000 Method for making and curing concrete - Compression and indirect tensile test specimens AS 1012.8.2 2000 Method for making and curing concrete - Flexure test specimens AS 1012.9 1999 Determination of the compressive strength of concrete specimens AS 1012.10 2000 Determination of indirect tensile strength of concrete cylinders ('Brazil' or splitting test) AS 1012.11 2000 Determination of the modulus of rupture AS 1012.12.2 1998 Determination of mass per unit volume of hardened concrete - Water displacement method AS 1012.13 1992 Determination of the drying shrinkage of concrete for samples prepared in the field or in the laboratory AS 1012.14 1991 Method for securing and testing cores from hardened concrete for compressive strength AS 1055 Acoustics - Description and measurement of environment noise AS 1055.1 1997 General procedures AS 1074 1989 Steel tubes and tubulars for ordinary service AS/NZS 1080 Timber - Methods of test AS/NZS 1080.1 1997 Moisture content AS 1085 Railway track material AS 1085.1 2002 Steel rails AS 1100 Technical drawing AS 1100.101 1992 General principles AS 1100.201 1992 Mechanical engineering drawing AS 1100.301 1985 Architectural drawing AS 1100.401 1984 Engineering survey and engineering survey design drawing AS/NZS 1100.501 2002 Structural engineering drawing GENERRAL GOLDEN ISLAND Project © VHT Engineering 5 Aug-11 AS 1102 Graphical symbols for electrotechnical documentation AS 1102.101 1989 General information and general index AS 1102.102 1997 Symbol elements, qualifying symbols and other symbols having general application AS 1102.103 1997 Conductors and connecting devices AS 1102.106 1997 Production and conversion of electrical energy AS 1102.107 1997 Switchgear, controlgear and protective devices AS 1102.108 1997 Measuring instruments, lamps and signalling devices AS 1102.111 1997 Architectural and topographical installation plans and diagrams AS 1110 ISO metric hexagon bolts and screws - Product grades A and B AS 1110.1 2000 Bolts AS 1110.2 2000 Screws AS 1111 ISO metric hexagon bolts and screws - Product grade C AS 1111.1 2000 Bolts AS 1111.2 2000 Screws AS 1112 ISO metric hexagon nuts AS 1112.1 2000 Style 1 - Product grades A and B AS 1112.2 2000 Style 2 - Product grades A and B AS 1112.3 2000 Product grade C AS 1112.4 2000 Chamfered thin nuts - Product grades A and B AS 1141 Methods for sampling and testing aggregates AS 1141.0 1999 List of methods AS 1141.4 2000 Bulk density of aggregate AS 1141.6.1 2000 Particle density and water absorption of coarse aggregate - Weighing-in-water method AS 1141.6.2 1996 Particle density and water absorption of coarse aggregate - Prycnometer AS 1141.11 1996 Particle size distribution by sieving AS 1141.12 1996 Materials finer than 75 υm in aggregates (by washing) AS 1141.13 2007 Material finer than 2µm AS 1141.14 1995 Particle shape, by proportional calliper AS 1141.15 1999 Flakiness index AS 1141.18 1996 Crushed particles in coarse aggregate derived from gravel AS 1141.21 1997 Aggregate crushing value AS 1141.22 1996 Wet/dry strength variation AS 1141.23 1995 Los Angeles value AS 1141.24 1997 Aggregate soundness - Evaluation by exposure to sodium sulfate solution AS 1141.25.1 2003 Degradation factor - Source rock AS 1141.25.2 203 Degradation factor - Coarse aggregate AS 1141.25.3 2003 Degradation factor - Fine aggregate AS 1141.32 1995 Weak particles (including clay lumps, soft and friable particles) in coarse aggregates AS 1141.37 1995 Iron unsoundness AS 1141.42 1999 Pendulum friction test AS 1141.50 1998 Resistance to stripping of cover aggregates from binders AS 1141.51 1996 Unconfined compressive strength of compacted materials AS 1141.6.1 2000 Particle density and water absorption of coarse aggregate - Weighing-in-water method AS 1141.6.2 1996 Particle density and water absorption of coarse aggregate – Prycnometer AS/NZS 1148 2001 Timber - Nomenclature - Australian, New Zealand and imported species AS 1152 1993 Specification for test sieves AS/NZS 1158 Lighting for roads and public spaces AS/NZS 1158.0 2005 Road lighting – Introduction AS/NZS 1158.1.1 2005 Road lighting - Vehicular traffic (Category V) lighting - Performance and installation design requirements AS/NZS 1158.1.3 1997 Road lighting - Vehicular traffic (Category V) lighting - Guide to design, installation, operation and maintenance AS 1158.2 2005 The lighting of urban roads and other public thoroughfares - Computer procedures for the calculation of light technical parameters for category A lighting AS/NZS 1158.3.1 2005 Pedestrian area (Category P) lighting - Performance and installation design requirements AS 1158.4 1987 The lighting of urban roads and other public thoroughfares - Supplementary lighting at pedestrian crossings AS/NZS 1158.6 2004 Luminaires AS 1160 1996 Bitumen emulsions for construction and maintenance of pavements AS 1163 1991 Structural steel hollow sections AS/NZS 1167 Welding and brazing - Filler metals GENERRAL GOLDEN ISLAND Project © VHT Engineering 6 Aug-11 AS/NZS 1167.1 2005 Filler metal for brazing and braze welding AS/NZS 1170 Structural design actions AS/NZS 1170.0 2002 General principles AS/NZS 1170.1 2002 Permanent, imposed and other actions AS/NZS 1170.2 2002 Wind actions AS 1170.4 1993 Minimum design loads on structures Earthquake loads AS 1181 1982 Method of measurement of civil engineering works and associated building works AS 1191 2002 Acoustics - Method for laboratory measurement of airborne sound insulation of building elements AS 1192 2004 Electroplated coatings - Nickel and chromium AS 1210 1997 Pressure vessels AS 1214 1983 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1221 1997 Fire hose reels AS 1228 2006 Pressure equipment - Boilers AS/NZS 1229 2002 Laundry troughs and tubs AS 1231 2000 Aluminium and aluminium alloys - Anodic oxidation coatings AS 1237 Plain washers for metric bolts, screws and nuts for general purposes AS 1237.1 2002 General plan AS/NZS 1252 1996 High strength steel bolts with associated nuts and washers for structural engineering AS/NZS 1254 2002 PVC (UPVC) pipes and fittings for storm and surface water applications AS/NZS 1260 2002 PVC-U pipes and fittings for drain, waste and vent application AS 1271 2003 Safety valves, other valves, liquid level gauges, and other fittings for boilers and unfired pressure vessels AS 1272 1974 Unsintered PTFE tape for thread sealing applications AS 1273 1991 Unplasticized PVC (UPVC) downpipe and fittings for rainwater AS/NZS 1276 Acoustics - Rating of sound insulation in buildings and of building elements AS/NZS 1276.1 1999 Airborne sound insulation AS 1277 1983 Acoustics - Measurement procedures for ducted silencers AS 1281 2001 Cement mortar lining of steel pipes and fittings AS 1284 Electricity metering AS 1284.1 2004 General purpose induction watthour meters AS 1284.4 2006 Socket mounting system AS 1288 2006 Glass in buildings - Selection and installation AS 1289 Methods of testing soils for engineering purposes AS 1289.2.1.1 2005 Soil moisture content tests - Determination of the moisture content of a soil - Oven drying method (standard method) AS 1289.3.1.1 1995 Soil classification tests - Determination of the liquid limit of a soil - Four point Casagrande method AS 1289.3.2.1 1995 Soil classification tests - Determination of the plastic limit of a soil - Standard method AS 1289.3.3.1 1995 Soil classification tests - Calculation of the plasticity index of a soil AS 1289.3.6.1 1995 Soil classification tests - Determination of the particle size distribution of a soil - Standard method of analysis by sieving AS 1289.3.6.3 2003 Determination of particle size distribution of a soil - Standard method of fine analysis using a hydrometer AS 1289.3.7.1 2002 Soil classification tests - Determination of the sand equivalent of a soil using a power-operated shaker AS 1289.4.2.1 1997 Determination of the sulfate content of a natural soil and the sulfate content of the groundwater - Normal method AS 1289.4.3.1 1997 Determination of the pH value of a soil - Electrometric method AS 1289.4.4.1 1997 Determination of the electrical resistivity of a soil - Method for sands and granular materials AS 1289.5.1.1 2003 Soil compaction and density tests- Determination of dry density/moisture content relation of a soil using standard compactive effort AS 1289.5.2.1 2003 Soil compaction and density tests- Determination of dry density/moisture content relation of a soil using modified compactive effort AS 1289.5.3.1 2004 Sand replacement method using a sand-cone pouring apparatus AS 1289.5.3.2 2004 Sand replacement method using a sand pouring can, with or without a volume displacer AS 1289.5.4.1 2007 Soil compaction and density tests - Compaction control test - Dry density ratio, moisture variation and moisture ratio AS 1289.5.4.2 1993 Methods of testing soils for engineering purposes AS 1289.5.5.1 1998 Soil compaction and density tests - Determination of the minimum and maximum dry density of a cohesionless material - Standard method GENERRAL GOLDEN ISLAND Project © VHT Engineering 7 Aug-11 AS 1289.5.6.1 1998 Soil compaction and density tests - Compaction control test - Density index method for a cohesionless material AS 1289.5.7.1 2006 Soil compaction and density tests- Compaction control test - Hilf density ratio and Hilf moisture variation AS 1289.5.8.1 2007 Soil compaction and density tests - Determination of field density and field moisture content of a soil using a nuclear surface moisture-density gauge - Direct transmission mode AS 1289.6.1.1 1998 Soil strength and consolidation tests- Determination of the California Bearing Ratio of a soil - Standard laboratory method for a remoulded specimen AS 1289.6.1.2 1998 Soil strength and consolidation tests - Determination of the California Bearing Ratio of a soil - Standard laboratory method for an undisturbed specimen AS/NZS 1301 Methods of test for pulp and paper AS 1301 419s 2004 Water vapour transmission rate of paper AS 1316 2003 Masonry cement AS 1319 1994 Safety signs for the occupational environment AS 1324 Air filters for use in general ventilation and airconditioning AS 1324.1 2001 Application, performance and construction AS 1324.2 2003 Methods of test AS/NZS 1328 Glued laminated structural timber AS/NZS 1328.1 1998 Performance requirements and minimum production requirements AS 1345 1995 Identification of the contents of pipes, conduits and ducts AS 1348 2002 Roads and traffic engineering - Glossary of terms AS 1349 1986 Bourdon tube pressure and vacuum gauges AS 1359 Rotating electrical machines-General requirements AS 1359.0 1998 Introduction and list of Parts AS 1359.5 2004 Three-phase cage induction motors - High efficiency and minimum energy - performance standards requirements AS 1359.30 1997 Preferred outputs and frame sizes AS 1359.31 1997 Three-phase induction motors - Operation on unbalanced voltages AS 1359.101 1997 Rating and performance AS 1359.102.1 1997 Methods for determining losses and efficiency - General AS 1359.102.2 1997 Methods for determining losses and efficiency - Calorimetric method AS 1359.106 1996 Methods of cooling (IC Code) AS 1359.107 1996 Classification of types of construction and mounting arrangements (IM Code) AS 1359.109 1998 Noise limits AS 1359.114 1997 Vibration measurement and limits AS 1366 Rigid cellular plastics sheets for thermal insulation AS 1366.1 1992 Rigid cellular polyurethane (RC/PUR) AS 1366.2 1992 Rigid cellular polyisocyanurate (RC/PIR) AS 1366.3 1992 Rigid cellular polystyrene - Moulded (RC/PS - M) AS 1366.4 1989 Rigid cellular plastics sheets for thermal insulation Rigid cellular polystyrene - Extruded (RC/PS-E) AS/NZS 1367 2000 Coaxial cable systems for the distribution of analogue television and sound signals in single and multiple unit installations AS 1375 1985 Industrial fuel-fired appliances (known as the SAA Industrial Fuel-fired Appliances Code) AS 1379 1997 Specification and supply of concrete AS 1385 1985 Textile floor coverings - Metric units and commercial tolerances for measurement AS/NZS 1390 1997 Cup head bolts with ISO metric coarse pitch threads AS/NZS 1393 1996 Coach screws - Metric series with ISO hexagon heads AS 1397 2001 Steel sheet and strip - Hot-dipped zinc-coated or aluminium/zinc-coated AS 1417 Receiving antennas for radio and television in the frequency range 30 MHz to 1 GHz AS 1417.1 1987 Construction and installation AS 1420 2001 ISO metric hexagon socket head cap screws AS/NZS 1421 1996 ISO metric hexagon socket set screws AS/NZS 1427 1996 ISO metric machine screws AS 1428 Design for access and mobility AS 1428.1 2001 General requirements for access - New building work AS 1428.2 1992 Enhanced and additional requirements - Buildings and facilities AS 1428.3 1992 Requirements for children and adolescents with physical disabilities AS/NZS 1428.4 2002 Tactile indicators AS 1432 2004 Copper tubes for plumbing, gasfitting and drainage applications AS 1443 2004 Carbon steels and carbon-manganese steel - Cold-finished bars AS 1444 1996 Wrought alloy steels - Standard , hardenability (H) series and hardened and tempered to designated mechanical properties GENERRAL GOLDEN ISLAND Project © VHT Engineering 8 Aug-11 AS 1445 1986 Hot-dipped zinc-coated or aluminium/zinc-coated sheet - 76 mm pitch corrugated AS 1450 1983 Steel tubes for mechanical purposes AS 1470 1986 Health and safety at work - Principles and practices AS/NZS 1477 2006 PVC pipes and fittings for pressure applications AS 1478 Chemical admixtures for concrete, mortar and grout AS 1478.1 2000 Admixtures for concrete AS 1530 Methods for fire tests on building materials, components and structures AS 1530.1 1994 Combustibility test for materials AS 1530.2 1993 Test for flammability of materials AS/NZS 1530.3 1999 Simultaneous determination of ignitability, flame propagation, heat release and smoke release AS 1530.4 2005 Fire-resistance tests of elements of building construction AS/NZS 1546 On-site domestic wastewater treatment units AS/NZS 1546.1 1998 Septic tanks AS/NZS 1546.2 2001 Waterless composting toilets AS/NZS 1547 2000 On-site domestic wastewater management AS 1548 1995 Steel plates for pressure equipment AS/NZS 1554 Structural steel welding AS/NZS 1554.1 2004 Welding of steel structures AS/NZS 1554.3 2002 Welding of reinforcing steel AS/NZS 1554.6 1994 Welding stainless steels for structural purposes AS 1562 Design and installation of sheet roof and wall cladding AS 1562.1 1992 Metal AS/NZS 1562.2 1999 Corrugated fibre-reinforced cement AS 1562.3 2006 Plastic AS 1565 1996 Copper and copper alloys - Ingots and castings AS 1566 1997 Copper and copper alloys - Rolled flat products AS/NZS 1567 1997 Copper and copper alloys-Wrought rods, bars and sections AS 1569 1998 Copper and copper alloys - Seamless tubes for heat exchangers AS/NZS 1571 1995 Copper - Seamless tubes for airconditioning and refrigeration AS 1572 1998 Copper and copper alloys - Seamless tubes for engineering purposes AS 1579 2001 Arc welded steel pipes and fittings for water and waste water AS 1580 Paints and related materials - Methods of test AS/NZS 1580.107.3 1997 Determination of wet film thickness by gauge AS/NZS 1580.108.2 2004 Dry film thickness - Paint inspection gauge AS/NZS 1580.481.1.2 1998 Coatings - Exposed to weathering - Discolouration (including bronzing) AS/NZS 1580.602.2 1995 Measurement of specular gloss of non-metallic paint films at 20 degrees, 60 degrees and 85 degrees (ISO 2813:1994) AS 1589 2001 Copper and copper alloy waste fittings AS/NZS 1594 2002 Hot-rolled steel flat products AS/NZS 1595 1998 Cold-rolled, unalloyed, steel sheet and strip AS/NZS 1596 2002 Storage and handling of LP Gas AS 1597 Precast reinforced concrete box culverts AS 1597.2 1996 Large culverts (from 1500 mm span and up to and including 4200 mm span and 4200 mm height) AS 1599 2006 Pressure-sensitive and water activated adhesive tape for packaging and office applications AS 1603 Automatic fire detection and alarm systems AS 1603.2 1997 Point type smoke detectors AS 1603.3 1996 Heat alarms AS 1603.5 1996 Manual call points AS 1603.7 1996 Optical beam smoke detectors AS 1603.8 1996 Multi-point aspirated smoke detectors AS 1603.11 2001 Visual warning devices AS 1603.13 1998 Duct sampling units AS 1603.15 2002 Remote indicators AS 1603.16 2002 In situ testers AS/NZS 1604 Specification for preservative treatment AS 1604.1 2005 Sawn and round timber AS/NZS 1604.2 2004 Reconstituted wood-based products AS/NZS 1604.3 2004 Plywood AS/NZS 1604.4 2004 Specification for preservative treatment Laminated veneer lumber (LVL) AS/NZS 1604.5 2005 Specification for preservative treatment Glued laminated timber products AS 1627 Metal finishing - Preparation and pretreatment of surfaces GENERRAL GOLDEN ISLAND Project © VHT Engineering 9 Aug-11 AS 1627.1 2003 Removal of oil, grease and related contaimination AS 1627.2 2002 Power tool cleaning AS 1627.4 2005 Abrasive blast cleaning AS 1627.5 2003 Pickling AS 1627.9 2002 Pictorial surface preparation standards for painting steel surfaces AS 1628 1999 Water supply - Metallic gate, globe and non-return valves AS 1631 1994 Cast grey and ductile iron non-pressure pipes and fittings AS 1646 various Elastomeric seals for waterworks purposes AS 1657 1992 Fixed platforms, walkways, stairways and ladders - Design, construction and installation AS/NZS 1664 Aluminium structures AS/NZS 1664.1 1997 Limit state design AS/NZS 1664.2 1997 Allowable stress design AS 1665 2004 Welding of aluminium structures AS/NZS 1668 The use of ventilation and airconditioning in buildings AS/NZS 1668.1 1998 Fire and smoke control in multi-compartment buildings AS 1668.2 1991 Mechanical ventilation for acceptable indoor quality AS 1668.2 2002 Ventilation design for indoor air contaminant control AS 1668.3 2001 Smoke control systems for large single compartments or smoke reservoirs AS 1670 Fire detection, warning control and intercom systems - System design, installation and commissioning AS 1670.1 2004 Fire AS 1670.3 2004 Fire alarm monitoring AS 1670.4 2004 Sound systems and intercom systems for emergency purposes AS 1670.6 1997 Smoke alarms AS 1672 Limes and limestones AS 1672.1 1997 Limes for building AS/NZS 1677 Refrigerating systems AS/NZS 1677.1 1998 Refrigerant classification AS/NZS 1677.2 1998 Safety requirements for fixed applications AS/NZS 1680 Interior lighting AS/NZS 1680.0 1998 Safe movement AS/NZS 1680.1 2006 General principles and recommendations AS 1680.2.1 1993 Circulation spaces and other general areas AS 1680.2.2 1994 Office and screen-based tasks AS 1680.2.3 1994 Educational and training facilities AS/NZS 1680.2.4 1997 Industrial tasks and processes AS 1680.2.5 1997 Hospital and medical tasks AS 1680.3 1991 Measurement, calculation and presentation of photometric data. AS 1682 Fire dampers AS 1682.1 1990 Specification AS 1682.2 1990 Installation AS 1683 Methods of test for elastomers AS 1683.23 2000 Rubber - Vulcanized - Determination of resistance to liquids AS 1684 Residential timber-framed construction AS 1684.2 2006 Non-cyclonic areas AS 1684.3 2006 Cyclonic areas AS 1684.4 2006 Simplified - Non-cyclonic areas AS 1692 2006 Steel tanks for flammable and combustible liquids AS 1697 2005 Installation and maintenance of steel pipe systems for gas AS 1710 2007 Non-destructive testing - Ultrasonic testing of carbon and low alloy steel plate - Test methods and quality classification AS/NZS 1715 1994 Selection, use and maintenance of respiratory protective devices AS 1720 Timber structures AS 1720.1 1997 Design methods AS 1720.2 2006 Timber properties AS 1720.4 2006 Fire-resistance for structural adequacy of timber members AS 1722 Pipe threads of Whitworth form AS 1722.1 1975 Sealing pipe threads AS 1725 2003 Galvanized rail-less chain-link security fencing and gates AS 1726 1993 Geotechnical site investigations AS/NZS 1730 1996 Washbasins AS/NZS 1734 1997 Aluminium and aluminium alloys - Flat sheet, coiled sheet and plate AS 1735 Lifts, escalators and moving walks AS 1735.1 2003 General requirements GENERRAL GOLDEN ISLAND Project © VHT Engineering 10 Aug-11 AS 1735.2 2001 Passenger and goods lifts – Electric AS 1735.5 2003 Escalators and moving walks (BS EN 115:1995, MOD) AS 1735.11 1986 Fire-rated landing doors AS 1735.12 1999 Facilities for persons with disabilities AS 1741 1991 Vitrified clay pipes and fittings with flexible joints - Sewer quality AS 1742 Various Manual of uniform traffic control devices AS 1742.2 1994 Traffic control devices for general use AS 1742.3 2002 Traffic control devices for works on roads AS 1742.14 1996 Traffic signals AS 1743 2001 Road signs - Specifications AS 1744 1975 Forms of letters and numerals for road signs (known as Standard alphabets for road signs) AS/NZS 1748 2006 Timber - Stress-graded - Product requirements for mechanically stress-graded timber AS 1761 1985 Helical lock-seam corrugated steel pipes AS 1762 1984 Helical lock-seam corrugated steel pipe - Design and installation AS/NZS 1768 2007 Lightning protection AS 1769 1975 Welded stainless steel tubes for plumbing applications AS 1789 2003 Electroplated zinc (electrogalvanized) coatings on ferrous articles (batch process) AS 1796 2001 Certification of welders and welding supervisors AS 1798 1992 Lighting poles and bracket arms-Preferred dimensions AS/NZS 1801 1997 Occupational protective helmets AS 1804 1976 Soft lead sheet and strip AS 1807 Cleanrooms, workstations, safety cabinets and pharmaceutical isolators - Methods of test AS 1807.6 2000 Determination of integrity of termination mounted HEPA filter installations AS 1810 1995 Timber - Seasoned cypress pine - Milled products AS 1830 2007 Grey cast iron AS 1831 2007 Ductile cast iron AS 1841 Portable fire extinguishers AS/NZS 1841.1 1997 General requirements AS/NZS 1841.2 1997 Specific requirements for water type extinguishers AS/NZS 1841.3 1997 Special requirements for wet-chemical type extinguishers AS/NZS 1841.4 1997 Specific requirements for foam type extinguishers AS/NZS 1841.5 1997 Special requirements for powder type extinguishers AS/NZS 1841.6 1997 Specific requirements for carbon dioxide type extinguishers AS/NZS 1841.8 1997 Specific requirements for non-rechargeable type extinguishers AS 1851 2005 Maintenance of fire protection systems and equipment AS/NZS 1859 Reconstituted wood-based panels – Specifications AS/NZS 1859.1 2004 Particleboard AS/NZS 1859.2 2004 Dry-processed fibreboard AS/NZS 1859.3 2005 Decorative overlaid wood panels AS/NZS 1859.4 2004 Wet-processed fibreboard AS 1860 Installation of particleboard flooring AS/NZS 1860.1 2002 Specifications AS 1860.2 2006 Installation AS/NZS 1865 1997 Aluminium and aluminium alloys - Drawn wire, rod, bar and strip AS/NZS 1866 1997 Aluminium and aluminium alloys - Extruded rod, bar, solid and hollow shapes AS/NZS 1867 1997 Aluminium and aluminium alloys - Drawn tubes AS/NZS 1873 Powder-actuated (PA) hand-held fastening tools AS/NZS 1873.4 2003 Fasteners AS 1874 2000 Aluminium and aluminium alloys - ingots and castings AS 1882 2002 Earth and bonding clamps AS 1891 Industrial fall-arrest systems and devices AS 1891.4 2000 Selection, use and maintenance AS/NZS 1892 Portable ladders AS/NZS 1892.1 1996 Metal AS 1897 1976 Electroplated coatings on threaded components (metric coarse series) AS 1905 Components for the protection of openings in fire-resistant walls AS 1905.1 2005 Fire-resistant doorsets AS 1905.2 2005 Fire-resistant roller shutters AS 1906 Retroreflective materials and devices for road traffic control purposes AS/NZS 1906.1 2007 Retroreflective sheeting AS/NZS 1906.2 2007 Retroreflective devices (non-pavement application) AS 1906.3 1992 Raised pavement markers (retroreflective and non-retroreflective GENERRAL GOLDEN ISLAND Project © VHT Engineering 11 Aug-11 AS 1910 2004 Water supply - Float control valves for use in hot and cold water AS 1926 Swimming pool safety AS 1926.1 2007 Safety barriers for swimming pools AS 1926.2 2007 Location of safety barriers for swimming pools AS 1926.3 2003 Water recirculation and filtration systems AS 1940 2004 The storage and handling of flammable and combustible liquids AS 2001 Methods of test for textiles AS 2001.2.14 1987 Physical tests - Determination of twist in yarns AS 2001.2.23 1990 Physical tests - Determination of linear density of textile yarn from packages AS 2001.3.4 1995 Chemical tests - Determination of solvent extractable matter AS 2001.4.16 1981 Colourfastness tests - Determination of colourfastness to dry cleaning solvents AS 2001.4.21 2006 Colourfastness tests - Determination of colourfastness to light using an artificial light source (mercury vapour, tungsten filament, internally phosphor-coated lamp) AS 2001.4.E01 2001 Colourfastness tests - Colourfastness to water AS 2001.6.1 1980 Miscellaneous tests - Determination of the resistance of textiles to certain insect pests AS 2001.7 2005 Methods of test for textiles. AS 2008 1997 Residual bitumen for pavements AS/NZS 2009 2006 Glass beads for pavement-marking materials AS/NZS 2022 2003 Anhydrous ammonia - Storage and handling AS/NZS 2023 1995 Baths for ablutionary purposes AS/NZS 2032 2006 Code of practice for installation of UPVC pipe systems AS 2033 1980 Installation of polyethylene pipe systems AS/NZS 2041 1998 Buried corrugated metal structures AS 2047 1999 Windows in buildings - Selection and installation AS 2049 2002 Roof tiles AS 2050 2002 Installation of roof tiles AS/NZS 2053 Conduits and fittings for electrical installations AS/NZS 2053.1 2001 General requirements AS/NZS 2053.2 2001 Rigid plain conduits and fittings of insulating material AS/NZS 2053.3 1995 Rigid plain conduits and fittings of fibre-reinforced concrete material AS/NZS 2053.4 1995 To be read in conjunction with AS/NZS 2053.1. AS/NZS 2053.5 2001 Corrugated conduits and fittings of insulating material AS/NZS 2053.6 2001 Profile-wall, smooth-bore conduits and fittings of insulating material AS/NZS 2053.7 2002 Rigid metal conduits and fittings AS/NZS 2053.8 1995 Flexible conduits and fittings of metal or composite material AS 2070 1999 Plastics materials for food contact use AS 2074 2003 Cast steels AS 2082 2000 Timber - Hardwood - Visually stress-graded for structural purposes AS/NZS 2098 Methods of test for veneer and plywood AS/NZS 2098.11 2005 Determination of formaldehyde emissions for plywood AS/NZS 2107 2000 Acoustics - Recommended design sound levels and reverberation times for building interiors AS/NZS 2111 Textile floor coverings - Tests and measurements AS/NZS 2111.3 1996 Determination of mass per unit area AS/NZS 2111.4 1996 Determination of surface pile mass above the substrate AS/NZS 2111.9 1996 Determination of the number of tufts per unit length and per unit area AS/NZS 2111.11 1996 Determination of total pile mass per unit area by complete dissection of textile floor coverings AS/NZS 2111.15 1996 Determination of withdrawal force required to remove tufts or pile from a textile floor covering AS/NZS 2111.16 1996 Determination of bond strength between backing components of a textile floor covering AS/NZS 2111.18 1997 Burning behaviour - Tablet test at ambient temperature AS/NZS 2111.19.1 1996 Colourfastness tests - Rubbing AS/NZS 2111.19.2 1996 Colourfastness tests - Shampoo solution AS 2118 Automatic fire sprinkler systems AS 2118.1 2006 General requirements AS 2118.2 1995 Wall wetting sprinklers (Drenchers) AS 2118.3 1997 Deluge AS 2118.4 1995 Residential AS 2118.6 1995 Combined sprinkler and hydrant AS/NZS 2119 1997 Textile floor coverings - Machine-made - Sampling and cutting specimens for physical tests GENERRAL GOLDEN ISLAND Project © VHT Engineering 12 Aug-11 AS 2120 Medical suction equipment AS 2120.3 1992 Suction equipment powered from a vacuum or pressure source AS 2124 1992 General conditions of contract AS 2127 1992 Form of formal instrument of agreement AS 2129 2000 Flanges for pipes, valves and fittings AS 2143 1978 Industrial and commercial steel shelving (Obsolescent) AS 2150 2005 Hot mix asphalt AS 2156 Walking tracks AS 2156.1 2001 Classification and signage AS 2156.2 2001 Infrastructure design AS 2157 1997 Cutback bitumen AS 2159 1995 Piling - Design and installation AS/NZS 2179 Specifications for rainwater goods, accessories and fasteners AS/NZS 2179.1 1994 Metal shape or sheet rainwater goods, and metal accessories and fasteners AS 2184 1985 Low voltage switchgear and controlgear Moulded-case circuit breakers for rated voltages up to and including 600 V a.c. and 250 V d.c. AS 2187 Explosives - Storage, transport and use AS 2187.1 1998 Storage AS 2187.2 2006 Use of explosives AS 2200 2006 Design charts for water supply and sewerage AS/NZS 2201 Intruder alarm systems AS/NZS 2201.1 2007 Client's premises - Design, installation, commissioning and maintenance AS 2201.2 2004 Monitoring centres AS 2201.3 1991 Detection devices for internal use AS 2201.4 1990 Wire-free systems installed in client's premises AS 2201.5 1992 Alarm transmission systems AS/NZS 2208 1996 Safety glazing materials in buildings AS 2209 1994 Timber - Poles for overhead lines AS/NZS 2269 2004 Plywood – Structural AS/NZS 2270 2006 Plywood and blockboard for interior use AS/NZS 2271 2004 Plywood and blockboard for exterior use AS 2273 1979 Steel library shelving (Obsolescent) AS/NZS 2280 2004 Ductile iron pressure pipes and fittings AS 2281 1993 Flexible cellular polyurethane for seat cushioning and bedding AS 2293 Emergency escape lighting and exit signs for buildings AS 2293.1 2005 System design, installation and operation AS/NZS 2293.2 1995 Inspection and maintenance AS 2293.3 2005 Emergency escape luminaires and exit signs AS/NZS 2310 2002 Glossary of paint and painting terms AS/NZS 2311 2000 Guide to the painting of buildings AS/NZS 2312 2002 Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings AS 2325 1993 Tungsten filament lamps for general service - Performance requirements AS 2327 Composite structures AS 2327.1 2003 Simply supported beams AS 2329 1999 Mastic adhesives for fixing wallboards AS 2331 Methods of test for metallic and related coatings AS 2331.1.3 2001 Local thickness tests - Magnetic method AS 2334 1980 Steel nails - Metric series AS 2338 2004 Preferred dimensions of wrought metal products AS 2341 various Methods of testing bitumen and related roadmaking products AS/NZS 2343 1997 Bullet-resistant panels and elements AS 2350 Methods of testing portland and blended cements AS/NZS 2350.0 1999 General introduction and list of methods AS/NZS 2350.1 2006 Sampling AS 2350.2 2006 Chemical composition AS/NZS 2350.3 2006 Normal consistency AS/NZS 2350.4 2006 Setting time AS/NZS 2350.5 2006 Determination of soundness AS 2350.7 2006 Determination of temperature rise during hydration of portland and blended cements AS/NZS 2350.8 2006 Fineness index by air permeability method AS 2350.9 2006 Determination of residue on the 45 µm sieve AS 2350.10 2006 Acid soluble calcium oxide content of blended cement GENERRAL GOLDEN ISLAND Project © VHT Engineering 13 Aug-11 AS/NZS 2350.11 2006 Compressive strength AS 2350.12 2006 Preparation of a standard mortar and moulding of specimens AS 2350.13 2006 Determination of drying shrinkage of cement mortars AS 2350.14 2006 Length change of portland and blended cement mortars exposed to a sulfate solution AS 2350.15 1995 Water-soluble chromate content of portland cement AS/NZS 2350.16 2006 Determination of air content of masonry cement AS/NZS 2350.17 2006 Determination of soundness of masonry cements AS/NZS 2350.18 2006 Determination of water retention of masonry cement AS 2358 1990 Adhesives - For fixing ceramic tiles AS 2381 Electrical equipment for explosive atmospheres-Selection, installation and maintenance AS 2381.6 1993 Increased safety e AS 2381.7 1989 Intrinsic safety i AS 2417 2001 Rotodynamic pumps - Hydraulic performance acceptance tests - Grades 1 and 2 AS 2419 Fire hydrant installations AS 2419.1 2005 System design, installation and commissioning AS 2419.2 1994 Fire hydrant valves AS 2419.3 1996 Fire brigade booster connections AS 2423 2002 Coated steel wire fencing products for terrestrial, aquatic and general use AS 2439 Perforated plastics drainage and effluent pipe and fittings AS 2439.1 1981 Perforated drainage pipe and associated fittings AS 2439.2 1983 Perforated effluent pipe and associated fittings for sewerage applications AS 2441 2005 Installation of fire hose reels AS 2444 2001 Portable fire extinguishers and fire blankets - Selection and location AS 2454 1993 Textile floor coverings - Terminology AS/NZS 2455 Textile floor coverings - Installation practice AS/NZS 2455.1 1995 General AS/NZS 2455.2 1996 Carpet tiles AS/NZS 2465 1999 Unified hexagon bolts, screws and nuts (UNC and UNF threads) AS 2507 1998 The storage and handling of agricultural and veterinary chemicals AS 2528 1982 Bolts, studbolts and nuts for flanges and other high and low temperature applications AS/NZS 2544 1995 Grey iron pressure fittings AS/NZS 2566 Buried flexible pipelines AS/NZS 2566.1 1998 Structural design AS/NZS 2566.2 2002 Installation AS 2568 1991 Medical gases - Purity of compressed medical breathing air AS 2578 Traffic signal controllers AS 2578.1 1983 Physical and electrical compatibility AS/NZS 2588 1998 Gypsum plasterboard AS/NZS 2589 Gypsum linings in residential and light commercial construction - Application and finishing AS/NZS 2589.1 1997 Gypsum plasterboard AS/NZS 2589.2 1997 Fibre reinforced gypsum plaster AS 2601 2001 The demolition of structures AS 2625 Mechanical vibration - Evaluation of machine vibration by measurements on non- rotating parts AS 2625.1 2003 General guidelines AS 2625.4 2003 Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ. AS 2634 1983 Chemical plant equipment made from glass-fibre reinforced plastics (GRP) based on thermosetting resins (Obsolescent) AS 2638 Sluice valves for water works purposes AS 2638.1 2002 Metal seated AS 2638.2 2002 Resilient seated AS/NZS 2648 Underground marking tape AS/NZS 2648.1 1995 Non-detectable tape AS 2657 1985 Powered rotary lawnmowers AS 2658 2003 LP Gas - Portable and mobile appliances AS 2663 Textiles - Fabrics for window furnishings AS 2663.1 1997 Uncoated fabrics AS 2663.2 1999 Coated curtain fabrics AS 2663.3 1999 Vertical and holland blinds AS 2665 2001 Smoke/heat venting systems- Design, installation and commissioning GENERRAL GOLDEN ISLAND Project © VHT Engineering 14 Aug-11 AS 2676 Guide to the installation, maintenance, testing and replacement of secondary batteries in buildings AS 2676.1 1992 Vented cells AS 2687 1997 Textiles - Upholstery fabrics for domestic and commercial use (excluding face-coated fabrics) AS 2688 1984 Timber doors (Obsolescent) AS/NZS 2699 Built-in components for masonry construction AS/NZS 2699.1 2000 Wall ties AS/NZS 2699.2 2000 Connectors and accessories AS/NZS 2699.3 2002 Lintels and shelf angles (durability requirements) AS 2700 1996 Colour standards for general purposes AS 2701 2001 Methods of sampling and testing mortar for masonry constructions AS/NZS 2712 2007 Solar and heat pump water heaters - Design and construction AS 2714 1993 The storage and handling of hazardous chemical materials - Class 5.2 substances (organic peroxides) AS 2726 Chainsaws - Safety requirements AS 2726.2 2004 Chainsaws for tree service AS 2727 1997 Chainsaws - Guide to safe working practices AS/NZS 2728 2007 Prefinished/prepainted sheet metal products for interior/exterior building applications - Performance requirements AS 2729 1994 Rolling bearings - Dynamic load ratings and rating life AS 2738 2000 Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings AS 2754 Adhesives for timber and timber products AS 2754.2 1991 Polymer emulsion adhesives AS 2758 Aggregates and rock for engineering purposes AS 2758.1 1998 Concrete aggregates AS 2758.2 1996 Aggregate for sprayed bituminous surfacing AS 2758.4 2000 Aggregate for gabion baskets and wire mattresses AS 2758.5 1996 Asphalt aggregates AS 2784 2002 Endless wedge belt and V-belt drives AS/NZS 2785 2000 Suspended ceilings - Design and installation AS 2796 Timber - Hardwood - Sawn and milled products AS 2796.1 1999 Product specification AS 2796.2 2006 Grade description AS 2796.3 1999 Timber for furniture components AS/NZS 2832 Cathodic protection of metals AS/NZS 2832.1 2004 Pipes and ables AS 2832.2 2003 Compact buried structures AS 2832.4 2006 Internal surfaces AS 2834 1995 Computer accommodation AS/NZS 2845 Water supply - Backflow prevention devices AS/NZS 2845.1 1998 Materials, design and performance requirements AS 2845.2 1996 Air gaps and break tanks AS 2845.3 1993 Field testing and maintenance AS 2848 Aluminium and aluminium alloys - Compositions and designations AS 2848.1 1998 Wrought products AS 2858 2004 Timber - Softwood - Visually graded for structural purposes AS/NZS 2865 2001 Safe working in a confined space AS 2867 1986 Farm structures - General requirements for structural design AS 2870 1996 Residential slabs and footings - Construction AS 2876 2000 Concrete kerbs and channels (gutters) - Manually or machine placed AS/NZS 2878 2000 Timber - Classification into strength groups AS 2887 1993 Plastic waste fittings AS 2890 Parking facilities AS 2890.1 2004 Off-street car parking AS 2890.3 1993 Bicycle parking facilities AS 2891 Methods of sampling and testing asphalt AS 2891.1 1986 Sampling of asphalt AS 2891.2.1 1995 Sample preparation - Mixing, quartering and conditioning of asphalt in the laboratory AS 2891.2.2 1995 Sample preparation - Compaction of asphalt test specimens using a gyratory compactor AS/NZS 2891.3.1 1997 Bitumen content and aggregate grading - Reflux method AS/NZS 2891.3.3 1997 Bitumen content and aggregate grading - Pressure filter method GENERRAL GOLDEN ISLAND Project © VHT Engineering 15 Aug-11 AS 2891.5 2004 Determination of stability and flow - Marshall procedure AS 2891.6 1993 Determination of stability by the modified Hubbard-Field procedure AS 2891.8 2005 Voids and density relationships for compacted asphalt mixes AS 2891.9.3 2005 Determination of bulk density of compacted asphalt - Mensuration method AS 2891.10 2005 Water and volatile oils content AS 2896 1998 Medical gas systems - Installation and testing of non-flammable medical gas pipeline systems AS/NZS 2904 1995 Damp-proof courses and flashings AS/NZS 2908 Cellulose-cement products AS/NZS 2908.1 2000 Corrugated sheets AS/NZS 2908.2 2000 Flat sheets AS 2913 2000 Evaporative airconditioning equipment AS/NZS 2918 2001 Domestic solid fuel burning appliances - Installation AS/NZS 2924 High pressure decorative laminates - Sheets made from thermosetting resins AS/NZS 2924.1 1998 Classification and specifications AS 2927 2001 The storage and handling of liquefied chlorine gas AS 2941 2002 Fixed fire protection installations - Pumpset systems AS 2946 1991 Suspended ceilings, recessed luminaries and air diffusers - Interface requirements for physical compatibility AS 2971 2002 Serially produced pressure vessels AS/NZS 3000 2007 Wiring rules AS/NZS 3002 2002 Electrical installations - Shows and carnivals AS/NZS 3003 2003 Electrical installations - Patient treatment areas of hospitals and medical and dental practices and dialyzing locations AS/ANZ 3008 Electrical installations - Selection of cables AS/ANZ 3008.1.1 1998 Cables for alternating voltages up to and including 0.6/1 kV - Typical Australian installation conditions AS/ANZ 3009 1998 Electrical installations - Emergency power supplies in hospitals AS/NZS 3010 2005 Electrical installations - Generating set AS 3011 Electrical installations - Secondary batteries installed in buildings AS/NZS 3011.2 1992 Sealed cells AS/NZS 3013 2005 Electrical installations - Classification of the fire and mechanical performance of wiring systems AS/NZS 3017 2001 Electrical installations - Testing and inspection guidelines AS/NZS 3080 2003 Telecommunications installations - Generic cabling for commercial premises (ISO/IEC 11801:2002, MOD) AS/NZS 3084 2003 Telecommunications installations - Telecommunications pathways and spaces for commercial buildings AS/NZS 3085 Telecommunications installations - Administration of communications cabling systems AS/NZS 3085.1 2004 Basic requirements AS/NZS 3100 2002 Approval and test specification - General requirements for electrical equipment AS/NZS 3102 2002 Electric duct heaters AS/NZS 3105 2007 Approval and test specification - Electrical portable outlet devices AS 3111 1994 Approval and test specification for miniature overcurrent circuit-breakers AS/NZS 3112 2004 Approval and test specification - Plugs and socket-outlets AS/NZS 3123 2005 Approval and test specification - Plugs, socket-outlets and couplers for general industrial application. AS/NZS 3131 2001 Approval and test specification - Plugs and socket-outlets for stationary appliances AS/NZS 3161 2005 Approval and test specification - Thermostats and energy regulators AS/NZS 3190 2002 Approval and test specification - Residual current devices (current-operated earth- leakage devices) AS/NZS 3350 Safety of household and similar electrical appliances AS/NZS 3350.2.34 2001 Particular requirements - Motor-compressors AS/NZS 3350.2.40 2001 Particular requirements for electrical heat pumps, airconditioners and dehumidifiers AS/NZS 3350.2.78 1996 Particular requirements - Outdoor barbecues AS/NZS 3439 Low-voltage switchgear and controlgear assemblies AS/NZS 3439.1 2002 Type-tested and partially type-tested assemblies AS/NZS 3439.2 2002 Particular requirements for busbar trunking systems (busways) AS/NZS 3439.3 2002 Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use - Distribution boards AS 3494 1997 Bidettes and bidets AS 3497 1998 Drinking water treatment units - Plumbing requirements AS/NZS 3500 Plumbing and Drainage AS/NZS 3500.0 2003 Glossary of terms GENERRAL GOLDEN ISLAND Project © VHT Engineering 16 Aug-11 AS/NZS 3500.1 2003 Water services AS/NZS 3500.2 2003 Sanitary plumbing and drainage AS/NZS 3500.3 2003 Stormwater drainage AS/NZS 3500.4 2003 Heated water services AS/NZS 3500.5 2000 Domestic installations AS/NZS 3504 2006 Fire blankets AS/NZS 3518 2004 Acrylonitrile butadiene styrene (ABS) compounds, pipes and fittings for pressure applications AS 3519 2005 Timber - Machine proof-grading AS 3541 Synthetic sporting surfaces AS 3541.1 1988 General principles AS 3566 Self-drilling screws for the building and construction industries AS 3566.1 2002 General requirements and mechanical properties AS 3566.2 2002 Corrosion resistance requirements AS 3568 1999 Oils for reducing the viscosity of residual bitumen for pavements AS 3571 1989 Glass filament reinforced thermosetting plastics (GRP) pipes - Polyester based - Water supply, sewerage and drainage applications AS 3575 1995 Clearing saws, brushcutters and grass trimmers - Safety requirements AS 3576 1998 Clearing saws, brushcutters and grass trimmers - Guide to safe working practices AS 3578 1993 Cast iron non-return valves for general purposes AS 3582 Supplementary cementitious materials for use with portland and blended cement AS 3582.1 1998 Fly ash AS 3582.2 2001 Slag - Ground granulated iron blast-furnace AS 3583 Methods of test for supplementary cementitous materials for use with portland cement AS 3583.1 1998 Determination of fineness by the 45 m sieve AS 3583.2 1991 Determination of fmoisture content AS 3583.3 1991 Determination of loss on ignition S 3583.12 1991 Determination of available alkali AS 3583.13 1991 Determination of chloride ion content AS 3583.14 1991 Determination of insoluble residue content AS 3590 Screen-based workstations AS 3590.2 1990 Workstation furniture AS 3600 2001 Concrete structures AS 3610 1995 Formwork for concrete AS 3623 1993 Domestic metal framing AS 3660 Termite management AS 3660.1 2000 New building work AS/NZS 3662 2005 Performance of showers for bathing AS/NZS 3666 Air-handling and water systems of buildings - Microbial control AS/NZS 3666.1 2002 Design, installation and commissioning AS/NZS 3666.2 2002 Operation and maintenance AS/NZS 3666.3 2000 Performance-based maintenance of cooling water systems AS/NZS 3678 1996 Structural steel - Hot-rolled plates, floorplates and slabs AS/NZS 3679 Structural steel AS/NZS 3679.1 1996 Hot-rolled bars and sections AS/NZS 3679.2 1996 Welded I sections AS 3680 1989 Polyethylene sleeving for ductile iron pipelines AS 3681 1989 Guidelines for the application of polyethylene sleeving to ductile iron pipelines and fittings AS 3688 2005 Water supply - Metallic fittings and end connectors AS 3690 1989 Installation of ABS pipe systems AS 3691 1989 Solvent cement and priming (cleaning) fluids for use with ABS pipes and fittings AS 3700 2001 Masonry structures AS 3705 2003 Geotextiles - Identification, marking, and general data AS 3706 Geotextiles - Methods of test ASD 3706.11 2004 Determination of durability - Resistance to degradation by light, heat and moisture AS 3715 2002 Metal finishing - Thermoset powder coatings for architectural applications of aluminium and aluminium alloys AS 3725 2007 Loads on buried concrete pipes AS 3725 Supp 1 2007 Loads on buried concrete pipes - Commentary (Supplement to AS 3725-1989) AS 3727 1993 Guide to residential pavements AS 3730 Guide to the properties of paints for buildings AS 3730.1 2006 Latex - Interior - Flat AS 3730.2 2006 Latex - Interior - Semi-gloss GENERRAL GOLDEN ISLAND Project © VHT Engineering 17 Aug-11 AS 3730.3 2006 Guide to the properties of paints for buildings AS 3730.5 2006 Solvent-borne - Interior - Semi-gloss AS 3730.6 2006 Solvent-borne - Interior/exterior - Full gloss enamel AS 3730.7 2006 Latex - Exterior - Flat AS 3730.8 2006 Latex - Exterior - Low gloss AS 3730.9 2006 Latex - Exterior - Semi-gloss AS 3730.10 2006 Latex - Exterior - Gloss AS 3730.12 2006 Latex - Interior - Gloss AS 3730.13 2006 Primer - Wood - Solvent-borne - Interior/exterior AS 3730.14 2006 Undercoat - Solvent-borne - Interior/exterior AS 3730.15 2006 Primer - Latex - For metallic zinc surfaces AS 3730.16 2006 Latex - Self-priming timber finish - Exterior AS 3730.17 2006 Primer - Wood - Latex - Interior/exterior AS 3730.18 2006 Undercoat/sealer - Latex - Interior/exterior AS 3730.21 2006 Primer - Solvent-borne - For ferrous metallic surfaces AS 3730.22 2006 Concrete and masonry sealer - Solvent-borne - Interior/exterior AS 3730.25 2006 Clear finish - Solvent-borne - Interior AS 3730.27 2006 Clear coatings for interior timber floors AS 3730.28 2006 Wood stain - Solvent-borne - Exterior AS 3730.29 2006 Solvent-borne - Exterior/interior - Paving paint AS 3731 Stationary batteries-Nickel-cadmium AS 3731.1 1995 Vented type AS 3731.2 1995 Valve-regulated type AS/NZS 3733 1995 Textile floor coverings - Cleaning maintenance of residential and commercial carpeting AS 3735 2001 Concrete structures retaining liquids AS 3740 2004 Waterproofing of wet areas within residential buildings AS 3743 2003 Potting mixes AS/NZS 3750 Paints for steel structures AS/NZS 3750.1 1994 Epoxy mastic (two-pack) - For rusted steel AS/NZS 3750.4 1994 Bitumen paint AS/NZS 3750.6 1994 Full gloss polyurethane (two-pack) AS/NZS 3750.9 1994 Organic zinc-rich primer AS 3750.13 1997 Epoxy primer (two pack) AS/NZS 3750.15 1998 Inorganic zinc silicate paint AS/NZS 3750.17 1998 Etch primers (single pack and two pack) AS/NZS 3760 2003 In-service safety inspection and testing of electrical equipment AS 3768 1990 Guide to the effects of temperature on electrical equipment AS 3780 1994 The storage and handling of corrosive substances AS 3784 Coatings for fire protection of building elements AS 3784.1 1990 Guide to selection and installation of sprayed mineral coatings AS 3786 1993 Smoke alarms AS/NZS 3788 2006 Pressure equipment - In-service inspection AS 3792 Ride-on lawnmowers AS 3792.1 1990 Powered rotary ride-on mowers AS 3798 2007 Guidelines on earthworks for commercial and residential developments AS 3799 1998 Liquid membrane-forming curing compounds for concrete AS/NSZ 3813 1998 Plastic monobloc chairs AS 3814 2005 Industrial and commercial gas-fired appliances AS 3818 Timber - Heavy structural products - Visually graded AS 3818.2 2004 Railway track timbers AS 3818.3 2001 Piles AS/NZS 3823 Performance of electrical appliances - Airconditioners and heat pumps AS/NZS 3823.1.1 1998 Non-ducted airconditioners and heat pumps - Testing and rating for performance AS/NZS 3823.1.2 2001 Test Methods - Ducted airconditioners and air-to-air heat pumps - Testing and rating for performance AS/NZS 3823.2 2005 Energy labelling and minimum energy performance standard (MEPS) requirements AS/NZS 3837 1998 Method of test for heat and smoke release rates for materials and products using an oxygen consumption calorimeter AS/NZS 3845 1999 Road safety barrier systems AS 3850 2003 Tilt-up concrete construction AS 3862 2002 External fusion-bonded epoxy coating for steel pipes AS 3865 1991 Calculation of the effects of short-circuit currents AS 3873 2001 Pressure equipment - Operation and maintenance GENERRAL GOLDEN ISLAND Project © VHT Engineering 18 Aug-11 AS/NZS 3879 2006 Solvent cements and priming fluids for use with unplasticized PVC (UPVC) pipes and fittings AS 3894 Site testing of protective coatings AS 3894.3 2002 Determination of dry film thickness AS 3894.5 2002 Determination of surface profile AS 3894.6 2002 Determination of residual contaminants. AS 3894.10 2002 Inspection report - Daily surface and ambient conditions AS 3894.11 2002 Equipment report AS 3894.12 2002 Inspection report – Coating AS 3894.13 2002 Inspection report – Daily AS 3894.14 2002 Inspection report - Daily painting AS/NZS 3896 1998 Waters - Examination for legionella including Legionella pneumophila AS/NZS 3947 Low voltage switchgear and controlgear AS/NZS 3947.3 2001 Switches, disconnectors, switch-disconnectors and fuse-combination units AS/NZS 3947.4.3 2000 Contactors and motor-starters - A.C. semiconductor controllers and contactors for non-motor loads AS/NZS 3947.5.5 2000 Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching function AS/NZS 3947.5.6 2000 Control circuit devices and switching elements - D.C.interface for proximity sensors and switching amplifiers (NAMUR) AS/NZS 3947.6.1 2001 Multiple function equipment - Automatic transfer switching equipment AS 3952 2002 Water supply - spring hydrant valve for waterworks purposes AS 3958 Ceramic tiles AS 3958.1 2007 Guide to the installation of ceramic tiles AS 3958.2 1992 Guide to the selection of a ceramic tiling system AS 3959 1999 Construction of buildings in bushfire-prone areas AS 3972 1997 Portland and blended cements AS 3996 2006 Metal access covers, road grates and frames AS 3999 1992 Thermal insulation of dwellings - Bulk insulation - Installation requirements AS 4000 1997 General conditions of contract AS/NZS 4020 2005 Testing of products for use in contact with drinking water AS/NZS 4025 Paints for equipment including ships AS/NZS 4025.1 1992 Solvent-borne - Interior and exterior - Full gloss enamel AS/NZS 4026 2001 Electric cables - For underground residential distribution systems AS/NZS 4029 Stationary batteries-Lead-acid AS 4029.1 1994 Vented type AS/NZS 4029.2 2000 Valve-regulated sealed type AS 4029.3 1993 Pure lead positive pasted plate type AS 4032 Water supply - Valves for the control of hot water supply temperatures AS 4032.3 2004 Requirements for field testing, maintenance or replacement of thermostatic mixing valves, tempering valves and end of line temperature control devices AS 4041 2006 Pressure piping AS 4044 1992 Battery chargers for stationary batteries AS 4049 Paints and related materials - Pavement marking materials AS 4049.1 2005 Solvent-borne paint - For use with surface applied glass beads AS 4049.2 2005 Thermoplastic pavement marking materials - For use with surface applied glass beads AS 4049.3 2005 Waterborne paint - For use with drop-on beads AS 4049.4 2006 High performance pavement marking systems AS 4055 2006 Wind loads for housing AS 4057 1992 Powered walk-behind and hand-held lawn trimmers and lawn edge trimmers - Mechanical safety requirements and test methods AS/NZS 4058 2007 Precast concrete pipes (pressure and non-pressure) AS 4060 1992 Loads on buried vitrified clay pipes AS 4070 1992 Protection of low-voltage electrical installations and equipment in MEN systems from transient overvoltages AS 4072 Components for the protection of openings in fire-resistant separating elements AS 4072.1 2005 Service penetrations and control joints AS 4085 1992 Automatic sliding door assemblies AS 4087 2004 Metallic flanges for waterworks purposes AS 4089 1993 Priming paint for steel - Single component - General purpose AS 4100 1998 Steel structures AS 4111 1993 Starters for fluorescent lamps - Performance requirements AS 4114 Spray painting booths, designated spray painting areas and paint mixing rooms. GENERRAL GOLDEN ISLAND Project © VHT Engineering 19 Aug-11 AS 4114.1 2003 Design, construction and testing AS 4114.2 2003 Installation and maintenance AS 4118 Fire sprinkler systems AS 4118.1.4 1994 Components - Valve monitors AS 4120 1994 Code of Tendering AS/NZS 4129 2000 Fittings for polyethylene (PE) pipes for pressure applications AS/NZS 4130 2003 Polyethylene (PE) pipes for pressure applications AS/NZS 4131 2003 Polyethylene (PE) compounds for pressure pipes and fittings AS 4139 2003 Fibre-reinforced concrete pipes and fittings AS 4145 Locksets AS 4145.1 1993 Glossary of terms AS 4145.2 1993 Mechanical locksets for doors in buildings AS 4145.3 2001 Mechanical locksets for windows in buildings AS 4145.4 2002 Padlocks AS 4154 1993 General access floors (elevated floors) AS 4155 Test methods for general access floors AS 4155.1 1993 Test for concavity and convexity AS 4155.2 1993 Test for twist AS 4155.3 1993 Test for panel squareness AS 4155.6 1993 Test for floor resistance for electrostatic control AS 4155.7 1993 Test for 300 mm x 300 mm concentrated load AS 4155.8 1993 Test for 25 mm x 25 mm concentrated load AS 4155.9 1993 Test for ultimate test load (safety factor tests for concentrated load) AS 4155.10 1993 Test for dynamic soft body impact load AS 4155.11 1993 Test for dynamic rolling loads with the tread made from resinous polymer AS 4155.12 1993 Test for pedestal strength by concentrated vertical load AS 4155.13 1993 Test for pedestal free movement by horizontal load AS 4155.14 1993 Test for pedestal strength by horizontal moment AS 4158 2003 Thermal-bonded polymeric coatings on valves and fittings for water industry purposes AS 4174 1994 Synthetic shade cloth AS 4178 1994 Electromagnetic door holders AS 4180 Drift loss from cooling towers - Laboratory measurement AS 4180.1 1994 Chloride balance method AS 4191 1994 Portable traffic signal systems AS 4192 2006 Illuminated flashing arrow signs AS 4198 1994 Precast concrete chambers for sewerage applications AS/NZS 4200 Pliable building membranes and underlays AS/NZS 4200.1 1994 Materials AS/NZS 4200.2 1994 Installation requirements AS/NZS 4251 Electromagnetic compatibility - Generic emission standard AS/NZS 4251.1 1999 Residential, commercial and light industry AS/NZS 4253 1994 Mailboxes AS 4254 2002 Ductwork for air-handling systems in buildings AS 4256 Plastic roof and wall cladding materials AS 4256.1 2006 General requirements AS 4256.2 2006 Unplasticized polyvinyl chloride (uPVC) building sheets AS 4256.3 2006 Glass fibre reinforced polyester (GRP) AS 4256.4 2006 Unplasticized polyvinyl chloride (uPVC) wall cladding boards AS 4256.5 2006 Polycarbonate AS 4260 1997 High efficiency particulate air (HEPA) filters - Classification, construction and performance AS/NZS 4266 Reconstituted wood-based panels - Methods of test AS/NZS 4266.16 2004 Formaldehyde emission - Dessicator method AS 4276 Water microbiology AS/NZS 4276.3.1 2007 Heterotrophic colony count methods - Pour plate method using plate count agar AS/NZS 4276.3.2 2003 Heterotrophic colony count methods - Plate count of water containing biocides AS/NZS 4284 1995 Testing of building facades AS 4285 2007 Skylights AS 4288 2003 Soft underlays for textile floor coverings AS 4290 2000 Design and installation of revolving doors AS/NZS 4296 1995 Cable trunking systems AS 4321 2001 Fusion-bonded medium density polyethelene coating and lining for pipes and fittings AS/NZS 4357 Structural Laminated Veneer Lumber AS/NZS 4357.0 2005 Specifications GENERRAL GOLDEN ISLAND Project © VHT Engineering 20 Aug-11 AS 4373 2007 Pruning of amenity trees AS/NZS 4383 Various Preparation of documents used in electro-technology AS/NZS 4386 Domestic kitchen assemblies AS/NZS 4386.1 1996 Kitchen units AS 4388 1996 A method of temperature-rise assessment by extrapolation for partially type-tested assemblies (PTTA) of low-voltage switchgear and controlgear AS/NZS 4389 1996 Safety mesh AS 4397 2007 Electroplated coatings of zinc on steel fasteners with imperial threads AS/NZS 4402 1996 Hexagon head tapping screws AS/NZS 4403 1996 Slotted pan head tapping screws AS/NZS 4404 1996 Slotted countersunk (flat) head tapping screws (common head style) AS/NZS 4405 1996 Slotted raised countersunk (oval) head tapping screws (common head style) AS/NZS 4406 1996 Cross recessed pan head tapping screws AS/NZS 4407 1996 Crossed recessed countersunk (flat) head tapping screws (common head style) AS/NZS 4408 1996 Crossed recessed raised countersunk (oval) head tapping screws AS/NZS 4409 1996 Hexagon washer head tapping screws AS/NZS 4410 1996 Hexagon flange head tapping screws AS 4419 2003 Soils for landscaping and garden use AS 4428 Fire detection, warning, control and intercom systems - Control and indicating equipment AS 4428.1 1998 Fire AS 4428.3 2004 Fire brigade panel AS 4428.4 2004 Intercommunication systems for emergency purposes AS 4428.5 1998 Power supply units AS 4428.6 1997 Alarm signalling equipment AS 4428.7 1999 Air-handling fire mode control panel AS 4428.9 2006 Requirements for wire-free alarm zone circuits AS 4428.10 1998 Alarm investigation AS 4429 1999 Methods of test and rating requirements for smoke-spill fans AS/NZS 4438 1997 Height adjustable swivel chairs AS 4440 2004 Installation of nailplated timber roof trusses AS 4441(Int) 2003 Oriented PVC (PVC-O) pipes for pressure applications AS/NZS 4442 1997 Office desks AS/NZS 4443 1997 Office panel systems - Workstations AS 4446 1999 Manufacture of nailplate-joined timber products AS 4454 2003 Composts, soil conditioners and mulches AS/NZS 4455 1997 Masonry units and segmental pavers AS/NZS 4456 Masonry units and segmental pavers - Methods of test AS 4456.0 2003 General introduction and list of methods AS 4456.3 2003 Determining dimensions AS 4456.5 2003 Determining breaking load of segmental paving units AS 4456.9 2003 Determining abrasion resistance AS/NZS 4456.10 2003 Determining resistance to salt attack AS 4484 2004 Gas cylinders for industrial, scientific, medical and refrigerant use - Labelling and colour coding AS 4486 Playgrounds and playground equipment AS 4486.1 1997 Development, installation, inspection, maintenance and operation AS/NZS 4491 1997 Timber - Glossary of terms in timber related Standards AS/NZS 4494 1998 Discharge of commercial and industrial liquid waste to sewer - General performance requirements AS/NZS 4505 1998 Domestic garage doors AS/NZS 4506 2005 Metal finishing - Thermoset powder coatings AS 4508 1999 Thermal resistance of insulation for ductwork used in building airconditioning AS/NZS 4534 2006 Zinc and zinc/aluminium-alloy coatings on steel wire AS/NZS 4548 Guide to long-life coatings for concrete and masonry AS/NZS 4548.1 1999 Wall coatings - Latex extensible AS/NZS 4548.2 1999 Latex finish coatings - High-build, low profile AS/NZS 4548.3 1999 Latex - Textured coatings - Non-aggregate AS/NZS 4548.4 1999 Latex - Textured coatings - Aggregate filled AS 4552 2005 Gas fired water heaters heaters for hot water supply and/or central heating AS 4566 2005 Flue cowls - Gas appliances AS/NZS 4586 2004 Slip resistance classification of new pedestrian surface materials AS 4594 Internal combustion engines - Performance AS 4594.0 1999 Application GENERRAL GOLDEN ISLAND Project © VHT Engineering 21 Aug-11 AS 4594.1 1999 Standard reference conditions, declarations of power, fuel and lubricating oil consumption and test methods AS 4597 1999 Installation of roof slates and shingles (Non-interlocking type) AS/NZS 4600 2005 Cold-formed steel structures AS/NZS 4602 1999 High visibility safety garments AS/NZS 4610 Furniture - School and educational AS/NZS 4610.2 1999 Chairs - Strength, durability and stability AS/NZS 4610.3 1999 Tables and storage furniture - Strength, durability and stability AS 4662 2003 Ceramic tiles - Definitions, classification, characteristics and marking (ISO 13006:1998) AS/NZS 4663 2004 Slip resistance measurement of existing pedestrian surfaces AS/NZS 4666 2000 Insulating glass units AS/NZS 4667 2000 Quality requirements for cut-to-size and processed glass AS/NZS 4668 2000 Glossary of terms used in the glass and glazing industry AS/NZS 4671 2001 Steel reinforcing materials AS/NZS 4672 Steel prestressing materials AS/NZS 4672.1 2007 General requirements AS/NZS 4672.2 2007 Testing requirements AS 4678 2002 Earth-retaining structures AS/NZS 4680 2006 Hot-dipped galvanized (zinc) coatings on fabricated ferrous articles AS/NZS 4688 Furniture - Fixed height chairs AS/NZS 4688.1 2000 Ergonomic and general requirements AS/NZS 4692 Electric water heaters AS/NZS 4692.1 2005 Energy consumption, performance and general requirements AS/NZS 4692.2 2005 Minimum Energy Performance Standard (MEPS) requirements and energy labelling AS 4744 Steel shoring and trench lining AS 4744.1 2000 Design AS 4750 2003 Electrogalvanized (zinc) coatings on ferrous hollow and open sections AS 4765 (Int) 2000 Modified PVC (PVC-M) pipes for pressure applications AS/NZS 4766 2006 Polyethylene storage tanks for water and chemicals AS/NZS 4782 Double-capped fluorescent lamps - Performance specifications AS/NZS 4782.1 2004 General (IEC 60081:2000, MOD) AS/NZS 4782.2 2004 Minimum Energy Performance Standard (MEPS) AS/NZS 4783 Performance of electrical lighting equipment - Ballasts for fluorescent lamps AS/NZS 4783.1 2001 Method of measurement to determine energy consumption and performance of ballasts lamp circuits AS/NZS 4783.2 2002 Energy labelling and minimum energy performance standards requirements AS 4785 Timber - Softwood - Sawn and milled products AS 4785.1 2002 Product specification AS 4785.2 2002 Grade description AS 4785.3 2002 Timber for furniture components AS 4786 Timber flooring AS 4786.2 2005 Sanding and finishing AS/NZS 4791 2006 Hot-dip galvanized (zinc) coatings on ferrous open sections, applied by an in-line process AS/NZS 4792 2006 Hot-dip galvanized (zinc) coatings on ferrous hollow sections, applied by a continuous or a specialized process AS 4794 2001 Non-return valves - Swing check and tilting disc AS 4806 Closed circuit television (CCTV) AS 4806.2 2006 Application guidelines AS 4809 2003 Copper pipe and fittings - Installation and commissioning AS 4843 2001 Synthetic weed blocking fabric AS/NZS 4858 2004 Wet area membranes AS/NZS 4859 Materials for the thermal insulation of buildings AS/NZS 4859.1 2002 General criteria and technical provisions AS 4902 2000 General conditions of contract for design and construct AS 4905 2002 Minor works contract conditions (Superintendent administered) AS/NZS 4911 2003 General conditions of contract for the supply of equipment without installation AS/NZS 4961 2003 Electric cables - Polymeric insulated - For distribution and service applications AS 4992 Ceramic tiles: Products for installation AS 4992.1 2006 Terms, definitions and specifications for adhesives AS/NZS 5000 Electric cables - Polymeric insulated AS/NZS 5000.1 2005 For working voltages up to and including 0.6/1 Kv (1.2) kV AS 5008 2001 Hygienic rendering of animal products AS 5010 2001 Hygienic production of ratite (emu/ostrich) meat for human consumption GENERRAL GOLDEN ISLAND Project © VHT Engineering 22 Aug-11 AS 5011 2001 Hygienic production of natural casings for human consumption AS 5039 2003 Security screen doors and security window grilles AS 5040 2003 Installation of security screen doors and window grilles AS/NZS 5065 2005 Polyethylene and polypropylene pipes and fittings for drainage and sewerage applications AS 5067 2003 Timber - Non-structural glued laminated - Performance and production requirements AS 5068 2006 Timber - Finger joints in structural products AS 5079 Filing cabinets AS 5079.1 2003 Lateral filing cabinets (ANSI BIFMA X3.2-1997, MOD) AS 5079.2 2003 Vertical filing cabinets ANSI BIFMA X3.3-1997, MOD) AS 5079.3 2003 Mobile pedestals (ANSI BIFMA X3.3-1998, MOD) ATS 5200 Technical specification for plumbing and drainage products ATS 5200.026 2004 Cold water storage tanks AS 5601 2004 Gas installations AS 5604 2005 Timber - Natural durability ratings AS ISO 5801 2004 Industrial fans - performance testing using standardized airways AS 6002 1999 Domestic electric meter enclosures AS/NZS 6400 2005 Water efficient products - Rating and labelling AS 7240 Fire detection and alarm systems AS 7240.2 2004 Control and indicating equipment AS 7240.5 2004 Point-type heat detectors AS 7240.6 2006 Carbon monoxide fire detectors using electro-chemical cells AS 7240.7 2004 Point-type smoke detectors using scattered light, transmitted light or ionisation AS 7240.13 2006 Compatibility assessment of system components AS 7240.15 2004 Multisensor fire detectors AS 7240.21 2006 Routing equipment AS/NZS ISO 9000 2006 Quality management and quality assuranace standards AS/NZS ISO 9001 2000 Quality management systems - Requirements AS ISO 9239 Reaction to fire tests for floor coverings AS ISO 9239.1 2003 Determination of the burning behaviour using a radiiant heat source AS ISO 9705 2003 Fire tests - Full-scale room test for surface products AS/NZS ISO 10005 2006 Quality management systems - Guidelines for quality plans AS/ISO 10013 2003 Guidelines for quality management system documentation AS ISO 11654 2002 Acoustics - Rating of sound absorption - Materials and systems AS 12239 2004 Fire detection and alarm systems - Smoke alarms (ISO 12239:2003, MOD) AS/NZS ISO/IEC 15018 2005 Information technology - Generic cabling for homes AS/NZS ISO 19011 2003 Guidelines for quality and/or environmental management systems auditing (ISO 19011:2002) AS/NZS ISO/IEC 24702 2007 Telecommunications installations - Generic cabling - Industrial premises AS 60044 Instrument transformers AS 60044.1 2007 Current transformers AS 60146 Semiconductor convertors AS 60146.1.1 2002 General requirements and line commutated converters - Specifications of basic requirements AS 60146.2 2001 Self-commutated semiconductor converters including direct d.c. converters AS/NZS 60155 2000 Glow-starters for fluorescent lamps AS 60269 Low voltage fuses AS 60269.1 2005 General requirements AS 60269.2.0 2005 Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) AS 60269.2.1 2005 Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Sections I TO VI: Examples of types of standardised fuses AS 60529 2004 Degrees of protection provided by enclosures (IP Code) AS/NZS 60598 Luminaires AS/NZS 60598.1 2003 General requirements and tests AS/NZS 60598.2.1 1998 Particular requirements - Fixed general purpose luminaires AS/NZS 60598.2.2 2001 Particular requirements - Recessed luminaires (IEC 60598-2-2:1996, MOD) AS/NZS 60598.2.4 2005 Particular requirements - Portable general purpose luminaries AS/NZS 60598.2.5 2002 Particular requirements - Floodlights AS/NZS 60598.2.6 1998 Particular requirements - Luminaires with built-in transformers or convertors for filament lamps AS/NZS 60598.2.18 1998 Particular requirements - Luminaires for swimming pools and similar applications GENERRAL GOLDEN ISLAND Project © VHT Engineering 23 Aug-11 AS/NZS 60598.2.19 2001 Particular requirements - Air handling luminaires (safety requirements) (IEC 60598.2.19:1981, MOD) AS/NZS 60598.2.25 2001 Particular requirements - Lminaires for use in clinical areas of hospitals and health care buildings (IEC 60598.2.25:1994 MOD) AS/NZS 60898 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations AS/NZS 60898.1 2004 Circuit-breakers for a.c. operation AS/NZS 60901 2003 Single-capped fluorescent lamps - Performance specifications AS/NZS 60921 2002 Ballasts for tubular fluorescent lamps - Performance requirements (IEC 60921:1988, MOD) AS/NZS 60923 1998 Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements AS/NZS 60929 2005 A.C. supplied electronic ballasts for tubular fluorescent lamps - Performance requirements AS 60947 Low voltage switchgear and controlgear AS 60947.1 2004 General rules AS 60947.2 2005 Circuit-breakers AS 60947.4.1 2004 Contactors and motor-starters - Electromechanical contactors and motor-starters AS 60947.4.2 2004 Contactors and motor-starters - A.C. semiconductor motor controllers and starters AS 60947.5.1 2004 Control circuit devices and switching elements - Electromechanical control circuit devices AS 60947.5.2 2004 Control circuit devices and switching elements - Proximity switches AS 60947.5.4 2004 Control circuit devices and switching elements - Methods of assessing the performance of low-energy contacts - Special tests AS 60947.6.2 2004 Multiple function equipment - Control and protective switching devices (or equipment) (CPS) AS 60947.8 2005 Control units for built-in thermal protection (PTC) for rotating electrical machines AS/NZS 60968 2001 Self ballasted lamps for general lighting services - Safety requirements (IEC 60968:1988, MOD) AS/NZS 60969 2001 Self ballasted lamps for general lighting services - Performance requirements AS/NZS 61000 Electromagnetic compatibility (EMC) AS/NZS 61000.3.2 2007 Limits - Limits for harmonic current emissions (equipment input current less than or equal to 16 A per phase) AS/NZS 6100.6.1 2006 Generic standards - Immunity for residential, commercial and light-industrial environments AS/NZS 61008 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (rcbos) AS/NZS 61008.1 2004 General rules AS/NZS 61009 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) AS/NZS 61009.1 2004 General rules AS/NZS 61048 2002 Auxiliaries for lamps - Capacitators for use in tubular fluorescent and other discharge lamp circuits - General safety requirements AS/NZS 61049 2002 Auxiliaries for lamps - Capacitators for use in tubular fluorescent and other discharge lamp circuits - Performance requirements AS/NZS 61347 Lamp controlgear AS/NZS 61347.1 2002 General and safety requirements (IEC 61347-1:2000, MOD) AS/NZS 61347.2.3 2004 Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps AS/NZS 61347.2.8 2003 Particular requirements for ballasts for fluorescent lamps AS/NZS 61558 Safety of power transformers, power supply units and similar AS/NZS 61558.1 2000 General requirements and tests. (IEC 61558-1:1997, MOD) AS 61800 Adjustable speed electrical power drive systems AS 61800.2 2004 General requirements - Rating specifications for low voltage adjustable frequency a.c. power drive systems AS 61800.3 2005 EMC product standard including specific test methods AS/NZS 61935 Testing of balanced communication cabling in accordance with ISO/IEC 11801 AS/NZS 61935.1 2006 Installed cabling AS/NZS 61935.2 2006 Patch cords and work area cords AS/NZS 62026 Low-voltage switchgear - Controller-device interfaces (CDI's) AS/NZS 62026.1 2001 General rules AS/NZS 62026.2 2001 Actuator sensor interface AS/NZS 62026.3 2001 DeviceNet AS/NZS 62026.5 2001 Smart distributed system (SDS) AS/NZS 62040 Uninterruptible power systems AS/NZS 62040.2 2001 Electromagnetic compatibility (EMC) requirements GENERRAL GOLDEN ISLAND Project © VHT Engineering 24 Aug-11 AS/NZS 62040.3 2002 Method of specifying the performance and test requirements AS/ACIF S008 2006 Requirements for authorised cabling products AS/ACIF S009 2006 Installation requirements for customer cabling (Wiring Rules) SAA HB 28 1997 Design of residential slabs and footings SAA HB 29 2007 Communications Cabling Manual, Module 2 Communications cabling handbook SAA HB 32 1995 Control of microbial growth in air-handling and water systems of buildings SAA HB 36 1993 Building in bushfire-prone areas - Information and advice SAA HB 40 The Australian Refrigeration and Air Conditioning Code of Good Practice SAA HB 40.1 2001 Reduction of emissions of fluorocarbon refrigerants in commercial and industrial refrigeration and airconditioning applications SAA HB 40.2 2001 Reduction of emissions of fluorocarbons in residential airconditioning applications SAA HB 48 1999 Steel structures design handbook SAA HB 49 Sporting facilities manual SAA HB 49.1 1993 Sports lighting SAA HB 69 Guide to traffic engineering practice SAA HB 69.14 1999 Bicycles SAA HB 81 Field guides for traffic control SAA HB 81.6 2003 Bituminous surfacing on roads SAA HB 90 Quality for the Construction Industry SAA HB 90.3 2000 The Construction Industry - Guide to ISO 9001:2000 SAA HB 195 2002 The Australian earth building handbook SAA HB 227 2003 Portable soccer goalposts - Manufacture, use and storage SAA HB 230 2006 Rainwater tank design and installation handbook SAA HB 243 2007 Communications Cabling Manual, Module 1:Australian regulatory arrangements SAA HB 301 2001 Electrical installations - designing to the Wiring Rules AAPA Advisory Note 7 2003 Guide to the selection, heating and storage of binders for sprayed sealing and hot mixed asphalt AAPA IG-3 2004 Asphalt plant process control guide (Implementation Guide series) ABIC MW-1 2003 Australian Building Industry Contract - Major works ABIC SW-1 2002 Australian Building Industry Contract - Simple works ACIF C524 2004 Industry Code - external communication cable AIRAH DA09 1998 Load estimation and psychrometrics ANCOLD 2007 Guidelines on acceptable flood capacity for dams 1995 AMCORD - a national resource document for residential development ASMM 1991 Australian standard method of measurement of building works AUSTROADS AGPT01 2005 Guide to Pavement Technology Part 1: Introduction to pavement technology AUSTROADS AGPT04B 2007 Guide to Pavement Technology - Part 4B: Asphalt AUSTROADS AP-3/90 1990 Guide to geotextiles AUSTROADS AP-44/97 1997 Asphalt recycling guide AUSTROADS AP-G1 2003 Rural road design – guide to geometric design of rural roads AUSTROADS AP-G11. Guide to traffic engineering practice AUSTROADS AP-G11.5 2005 Intersections at grade AUSTROADS AP-G11.6 1993 Roundabouts AUSTROADS AP-G11.10 2004 Local area traffic management AUSTROADS AP-G11.13 1995 Pedestrians AUSTROADS AP-G11.14 1999 Bicycles AUSTROADS AP-G17 2004 Pavement design - a guide to the structural design of road pavements AUSTROADS AP-G34 2006 Design Vehicles and Turning Path Templates (Includes CD) AUSTROADS AP-G41 2002 Bitumen sealing safety guide (2nd edition) (incl. errata sheet) AUSTROADS AP-G69 2002 Urban road design - guide to the geometric design of major urban roads AUSTROADS AP-G-76 2004 Sprayed sealing guide AUSTROADS AP-R211 2002 Geometric design for trucks - when, where and how? AUSTROADS AP-R246 2004 Salinity and rising water tables AUSTROADS AP-R258 2004 Sprayed seal design - 2003/04: summary AUSTROADS AP-T18 2002 Austroads framework for specifying asphalt AUSTROADS AP-T36 2006 Pavement design for light traffic: a supplement to Austroads pavement design guide. AustroadsTechnical Report AUSTROADS AP-T41 2006 Specification framework for polymer modified binders and multigrade bitumens AUSTROADS AP-T42 2006 Guide to the Selection and Use of Polymer Modified Binders and Multigrade Bitumens AUSTROADS AP-T84 2007 Application of the analytic hierarchy process in road asset management: User manual AUSTROADS AP-T85 2007 Optimum use of granular bases: material selection for detailed performance evaluation CBPI Techniques 05 1992 Open fireplace design and construction CBPI TN 21A 1985 Design of free-standing clay-brick walls CIA CPN35 2003 Fibres in concrete GENERRAL GOLDEN ISLAND Project © VHT Engineering 25 Aug-11 CIA Z48 2002 Precast concrete handbook City of Sydney Guidelines for erosion and sediment control on building sites CMAA T46 1997 Concrete segmental pavements - detailing guide CPAA Concrete pipe jacking CPAA 1990 Jacking design guidelines: design manual CSIRO Bulletin 5 1987 Earth-wall construction ICANZ 2003 Industry Code of Practice for the Safe use of Glass Wool and Rock Wool Insulation IEA 1997 Australian rainfall and runoff - a guide to flow estiomation. 4th ed. IEA Queensland 1996 Soil erosion and sediment control: engineering guidelines for Queensland construction sites/ Witheridge, Grant and Walker, Robert LANDCOM 2004 Managing urban stormwater, soils and construction. 4th ed. NASH 2005 NASH Standard: Residential and low-rise steel framing NOHSC 2002 2005 Asbestos Code of Practice for the safe removal of Asbestos Second edition [NOHSC:2002 (2005)] NPWC 3 1981 General conditions of contract. NPWC Edition 3 NSW Department of Commerce MEW E101 Electrical services minimum requirements NSW Department of Land and Water Conservation 1992 Urban erosion and sediment control field guide NSW GC21 2003 New SouthWwales Government GC21 General conditions of contract (Edition 1) NSW Government 1938 Soil Conservation Act 1938 NSW Government 1912 Water Act 1912 NSW Public Works Public Works Department manual of practice - sewage design NSW Public Works 1986 Public Works Department manual of practice - sewage pumping station design PCA 2004 Plumbing Code of Australia 2004 Queensland Department of Main Roads 2002 Road drainage design manual. Chapter 5. Erosion and sediment control Queensland Government 2002 Queensland dam safety management guidelines RESOURCE NSW 2003 Specification for supply of recycled material for pavements, earthworks and drainage RTA QA Specification 3253 2006 Bitumen for pavements RTA QA Specification DCM R141 2006 Pavement marking RTA Test Method T114 2001 Maximum dry compressive strength of road materials RTA Test Method T116 2001 Determination of unconfined compressive strength of remoulded road materials which are self cementing RTA Test Method T130 2001 Dry density - moisture relations for mixtures of road materials stabilised or modified with proportions of cement RTA Test Method T131 2000 Determination of unconfined compressive strength of road materials stabilised or modified with proportions of cement RTA Test Method T160 2001 Benkelman Beam deflection test RTA Test Method T171 2001 Modified Texas triaxial compression test for disturbed soils, soil aggregates and crushed rocks RTA Test Method T240 2006 Texture depth of coarse textured road surfaces RTA Test Method T1160 2001 Low temperature recovery of preformed polychloroprene elastomeric joint seals for bridge structures RTA Test Method T1161 2001 High temperature recovery of preformed polychloroprene elastomeric joint seals for bridge structures RTA Test Method T1163 2001 Resistance of vulcanised rubber to the absorption of oil RTA Test Method T1192 2001 Adhesion of sealant RTA Test Method T1193 2001 Accelerated ageing of cured sealant SSL 2003 ActivFire Register of Fire Protection Equipment (formerly SSL Register of Accredited Products - Fire Protection Equipment) SUSDP 2006 Standard for the Uniform Scheduling of Drugs and Poisons No. 21 Appendix P - Uniform Paint Standard University of WA 1994 Plant adaptations in respect of nutrient uptake and utilization: using wetlands for nutrient stripping. Seminar paper/ Pate, J S WA Department of GENERRAL GOLDEN ISLAND Project © VHT Engineering 26 Aug-11 Environmental Protection 1996 A guideline for the prevention of dust and smoke pollution from land development sites in Western Australia WS-SPEC 2001 WS-SPEC (CD-ROM) Water Services Specification WSA 01 2001 Polyethylene Pipeline Code 2004 3rd edition Version 3.1 WSA 02 2004 Sewerage Code of Australia Version 2.3 WSA 03 2004 Water Supply Code of Australia Version 2.3 WSA 04 2005 Sewage Pumping Station Code of Australia Version 2.1 British BS 410 Test sievesTechnical requirements and testing BS 410-1 2000 Test sieves of metal wire cloth BS 410-2 2000 Test sieves of perforated metal plate BS 779 1989 Specification for cast iron boilers for central heating and indirect hot water supply (rated output 44 kW and above) BS 848 Fans for general purposes BS 848-1 1997 Performance testing using standardised airways BS 848-2.6 2000 Methods of noise testing. Airborne noise emitted by small air-moving devices. Section 6: Airborne noise emitted by small air-moving devices BS 855 1990 Specification for welded steel boilers for central heating and indirect hot water supply (rated output 44 kW to 3 MW) BS 1042 Various Measurement of fluid flow in closed conduits BS 1217 1997 Specification for cast stone BS 1711 1975 Specification for solid rubber flooring BS 2571 1990 Specification for general-purpose flexible PVC compounds for moulding and extrusion BS 4051 1987 Method for determination of thickness of textile floor coverings BS 4255 Rubber used in preformed gaskets for weather exclusion from buildings BS 4255-1 1986 Specification for non-cellular gaskets BS 4485 Water cooling towers BS 4485-2 1988 Methods for performance testing BS 5080 Methods of test for structural fixings in concrete and masonry BS 5080-1 1993 Method of test for tensile loading BS 5080-2 1986 Method for determination of resistance to loading in shea BS 5642 Sills and copings BS 5642-1 1978 Specification for window sills of precast concrete, cast stone, clayware, slate and natural stone BS 5921 1980 Methods for determination of size, squareness and straightness of edge of textile floor covering tiles BS 6423 1983 Code of practice for maintenance of electrical switchgear and controlgear for voltages up to and including 1 kV BS 7190 1989 Method for assessing thermal performance of low temperature hot water boilers using a test rig BS 8204-1 2003 In-situ floor finishes Code of practice for concrete bases and screeds to receive in-situ floorings BS 8298 1994 Code of practice for design and installation of natural stone cladding and lining BS EN 303-1 1999 Heating boilers. Heating boilers with forced draught burners. BS EN 548 2004 Resilient floor coverings. Specification for plain and decorative linoleum BS EN 593 2004 Industrial valves. Metallic butterfly valves BS EN 650 1997 Resilient floor coverings. Polyvinyl chloride floor coverings on jute backing or on polyester felt backing or on polyester felt with polyvinyl chloride backing. Specification BS EN 651 1997 Resilient floor coverings. Polyvinyl chloride floor coverings with foam layer. Specification BS EN 685 2005 Resilient and laminate floor coverings. Classification BS EN 688 1997 Resilient floor coverings. Specification for corklinoleum BS EN 1886 1998 Ventilation for buildings. Air handling units. Mechanical performance BS EN 10216 Seamless steel tubes for pressure purposes. Technical delivery conditions BS EN 10216-1 2002 Non-alloy steel tubes with specified room temperature properties BS EN 10217 Welded steel tubes for pressure purposes - Technical delivery conditions BS EN 10217-1 2002 Non-alloy steel tubes with specified room temperature properties BS EN 12104 2000 Resilient floor coverings. Cork floor tiles. Specification BS EN 12878 2005 Pigments for the colouring of building materials based on cement and/or lime. Specifications and methods of test BS EN 13055 Lightweight aggregates BS EN 13055-1 2002 Lightweight aggregates for concrete, mortar and grout GENERRAL GOLDEN ISLAND Project © VHT Engineering 27 Aug-11 BS EN ISO 5136 2003 Acoustics. Determination of sound power radiated into a duct by fans and other air- moving devices. In-duct method CIBSE Commissioning Codes (CC) CIBSE CCA 1996 Commissioning Code A: Air distribution systems CIBSE CCB 2002 Commissioning Code B - Boilers CIBSE CCC 2001 Commissioning Code C - Automatic controls CIBSE CCR 2002 Commissioning Code R Refrigerating systems CIBSE CCW 2003 Commissioning Code W - Water distribution systems American AAMA 701/702 2004 Combined voluntary specification for pile Weatherstripping and replaceable fenestration weatherseals AAMA 800 2005 Voluntary specifications and test methods for sealants (Compilation of standards & test methods 802.3, 803.3, 804.3, 805.2, 806.3, 807.3) AAMA 1503 1998 Voluntary test method for thermal transmittance and condensation resistance of windows, doors and glazed wall sections AAMA 2605 2005 Voluntary specification, performance requirements and test procedures for superior performing organic coatings on aluminum extrusions and panels AAMA CW-13 1985 Structural Sealant Glazing Systems ( a design guide) AASHTO M190 2004 Standard specification for bituminous-coated corrugated metal culvert pipe and pipe arches AATCC TM 134 2006 Electrostatic propensity of carpets ACADS-BSG Airconditioning design software ANSI/ASHRAE 70 2006 Method of testing the performance of air outlets and inlets ANSI/ASHRAE 135 2004 BACnet(r) A data communication protocol for building automation and control networks API Spec 5L 2004 Specification for line piped ARI 410 2001 Forced-circulation air-cooling and air-heating coils ARI 450 1999 Water-cooled refrigerant ccndensers, remote type ARI 460 2005 Remote mechanical-draft air-cooled refrigerant condensers ARI 480 2001 Refrigerant-cooled liquid coolers, remote type ARI 540 2004 Performance rating of positive displacement refrigerant compressors and compressor units ARI 550/590 2003 Water chilling packages using the vapor compression cycle ARI 710 2004 Liquid-line driers ARI 890 2001 Rating of air diffusers and air diffuser assemblies ASHRAE 1998 Cooling and heating load calculation principles. Research Project 875 ASHRAE Guideline 2 2005 Engineering analysis of experimental data ASHRAE 111 1988 Practices for measurement, testing, adjusting and balancing of building heating, ventilation, airconditioning and refrigeration systems ASME PTC 23 2003 Atmospheric water cooling equipment ASTM A53/A53M 2006 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless ASTM A240/A240M 2006 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276 2006 Standard Specification for Stainless Steel Bars and Shapes ASTM A312/A312M 2006 Standard Specification for Seamless and Welded and Heavily Cold Worked Austenitic Stainless Steel Pipes ASTM A554 2003 Standard Specification for Welded Stainless Steel Mechanical Tubing ASTM A820/820M 2006 Standard Specification for steel fibers for fiber-reinforced concrete ASTM B68 2005 Standard Specification for Seamless Copper Tube, Bright Annealed ASTM B117 2003 Standard practice for operating salt spray (fog) apparatus ASTM C97 2002 Standard Test Methods for Absorption and Bulk Specific Gravity of Dimension Stone ASTM C99 2006 Standard Test Method for Modulus of Rupture of Dimension Stone ASTM C120 2006 Standard Test Methods of Flexure Testing of Slate (Modulus of Rupture, Modulus of Elasticity) ASTM C121 2006 Standard Test Method for Water Absorption of Slate ASTM C170 2006 Standard Test Method for Compressive Strength of Dimension Stone ASTM C171 2003 Standard Specification for Sheet Materials for Curing Concrete ASTM C217 2004 Standard Test Method for Weather Resistance of Slate ASTM C534 2007 Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form ASTM C793 2005 Standard Test Method for effects of laboratory accelerated weathering on elastomeric joint sealants ASTM C794 2006 Standard test method for adhesion-in-Peel of elastomeric joint sealants GENERRAL GOLDEN ISLAND Project © VHT Engineering 28 Aug-11 ASTM C880 2006 Standard Test Method for Flexural Strength of Dimension Stone ASTM C920 2005 Standard Specification for Elastomeric Joint Sealants ASTM C1048 2004 Standard Specification for Heat Treated Flat Glass-Kind HS, Kind FT Coated and Uncoated Glass ASTM C1087 2006 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems ASTM C1311 2002 Standard Specification for Solvent Release Sealants ASTM D792 2000 Standard Test Methods for density and specific gravity (relative density) of plastics by displacement ASTM D897 2001 Standard Test Method for Tensile Properties of Adhesive Bonds ASTM D1002 2005 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) ASTM D2240 2005 Standard Test method for rubber property – durometer hardness ASTM D2434 2006 Standard Test Method for permeability of granular soils (Constant Head) ASTM D2628 2005 Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements ASTM D2688 2005 Standard Test Method for Corrosivity of Water in the Absence of Heat Transfer (Weight Loss Methods) ASTM D2835 2003 Standard Specification for Lubricant for Installation of Preformed Compression seals in Concrete Pavements ASTM D3330M 2004 Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape at 180 degree Angle ASTM D3652M 2006 Standard Test Methods for Thickness of Pressure-Sensitive and Gummed Tapes ASTM D3654M 2006 Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes ASTM D3715M 2004 Standard Practice for Quality Assurance of Pressure-Sensitive Tapes ASTM D5116 2006 Standard Guide for Small-Scale Environmental Chamber Determinations of Organic Emissions From Indoor Materials/Products ASTM D6694 2007 Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing ASTM D7012 2007 Standard Test Method for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures ASTM E72 2005 Standard method of conducting strength tests of panels for building construction ASTM E96/E96M 2005 Standard Test Methods for Water Vapor Transmission of Materials ASTM E488 2003 Standard Test Methods for Strength of Anchors in Concrete and Masonry Elements ASTM E695 2003 Standard method of measuring relative resistance of wall, floor and roof construction to impact loading ASTM E773 2001 Standard Test Method for Accelerated Weathering of Sealed Insulating Glass Units ASTM E1155 2001 Standard Test Method for Determining FF Floor Flatness and FL Floor Levelness Numbers [Metric] Carrier Manual for calculating cooling and heating loads - manual method Carrier E20 Manual for calculating cooling and heating loads - electronic method CTI ATC AcceptanceTest Code CTI ATC-105 2000 Part I - Test Procedure: Methods and instrumentation for testing mechanical draft and natural draft cooling towers. Part II - Evaluation of results. NFRC 100 2004 Procedure for determining fenestration product U-factors. NFRC 200 2004 Procedure for determining fenestration product solar heat gain coefficient and visible transmittance at normal incidence. SMACNA 2003 Fibrous glass duct construction standards SAE AMS-S-8802 2005 Sealing compound, temperature resistant, integral fuel tanks and fuel cell cavities, high adhesion Trane Trace 700 Software for calculating cooling and heating loads UL 181 2005 Standard for factory-made air ducts and air connectors UL 984 1996 Standard for hermetic refrigerant motor-compressors International DIN EN 733 1995 End-suction centrifugal pumps, rating 10 bar, with bearing bracket - nominal duty point, main dimensions, designation system DIN EN 1051 Glass in buildings - Glass blocks and glass paver units DIN EN 1051-1 2003 Definitions, requirements, test methods and inspections IEC 60034 Rotating electrical machines IEC 60034-5 2006 Degree of protection provided by the integral design of rotating electrical machines (IP Code) – Classification. IEC 60034-8 2007 Terminal markings and direction of rotation GENERRAL GOLDEN ISLAND Project © VHT Engineering 29 Aug-11 IEC 60034-12 2002 Starting performance of single-speed three-phase cage induction motors for voltages up to and including 660 V IEC 60072 Dimensions and output series for rotating electrical machines IEC 60072-3 1994 Small built-in motors - Flange numbers BF 10 to BF50 IEC 60085 2004 Electrical insulation - Thermal classification IEC 60169 Radio-frequency connectors IEC 60169-2 1965 Coaxial unmatched connector IEC 60169-24 1991 Radio-frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable distribution systems (Type F) IEC 60188 2001 High-pressure mercury vapour lamps - performance specifications IEC 60192 2001 Low-Pressure sodium vapour lamps - performance specifications IEC 60357 2002 Tungsten halogen lamps (non-vehicle) IEC 60662 2002 High-pressure sodium vapour lamps IEC 60793 Optical fibres IEC 60793-2-10 2007 Product specifications - Sectional specification for category A1 multimode fibres IEC 60794 Optical fibre cables IEC 60794-1-2 2003 Generic specification - Basic optical cable test procedures IEC 60831 Shunt capacitors for a.c. power systems having a rated voltage above 1000 V IEC 60831-1 2002 General IEC 60831-2 1995 Endurance testing IEC 60893 Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes IEC 60893-1 2004 Definitions, designations and general requirements IEC 60947 Low-voltage switchgear and controlgear IEC 60947-5-5 2005 Control circuit devices and switching elements – Electrical emergency stop device with mechanical latching function ISO 717 Acoustics - Rating of sound insulation in buildings and of building elements ISO 717-1 1996 Airborne sound insulation ISO 2063 2005 Thermal spraying -- Metallic and other inorganic coatings -- Zinc, aluminium and their alloys ISO 2858 1975 End suction centrifugal pumps (rating 16 bar) - designation, nominal duty point and dimensions ISO 5135 1997 Acoustics - Determination of sound power levels of noise from air-terminal devices, air- terminal units, dampers and valves by measurement in a reverberation room ISO 5801 1997 Industrial fans - performance testing using standardized airways ISO 5802 2001 Industrial fans - performance testing in situ ISO 8501 Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness ISO 8501-1 2007 Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings ISO 8501-2 1994 Preparation grades of previously coated steel substrates after localized removal of previous coatings ISO 8573 Compresed Air ISO 8573-1 2001 Contaminants and purity classes ISO 8770 2003 High-density polyethylene (PE-HD) pipes and fittings for soil and waste discharge (low and high temperature) systems inside buildings; specifications ISO/IEC 8802 Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements ISO/IEC 8802-3 2000 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications ISO 9001 2000 Quallity management systems – Requirements ISO 10302 1996 Acoustics - method for the measurement of airborne noise emitted by small air-moving devices ISO 11600 2002 Building construction - Jointing products - Classification and requirements for sealants ISSA TB 100 1990 Test Method for Wet Track Abrasion Slurry Surfaces ISSA TB 114 1990 Wet Stripping Test for Cured Slurry Seal Mix ISSA TB 139 1990 Test Method to Classify Emulsified Asphalt/Aggregate Mixture Systems by Modified Cohesion Tester Measurement of Set and Cure Characteristics ISSA TB 144 1990 Test Method for Classification of Aggregate Filler - Bitumen Compatibility by Schulze-Breuer and Ruck Procedures ISTT 2004 Glossary of trenchless terms JIS A 5212 1993 Hollow glass blocks GENERRAL GOLDEN ISLAND Project © VHT Engineering 30 Aug-11 0171 GENERAL REQUIREMENTS 1 GENERAL 1.1 PRECEDENCE Precedence General: Requirements of subsequent worksections of the specification override conflicting requirements in this worksection. English Version specification override conflicting VietNamese Version 1.2 CROSS REFERENCES Common requirements Associated worksections: Conform to the following: - Adhesives, seals and fasteners. - Fire-stopping. - Metals and prefinishes. - Termite management. - Timber finishes and treatment. - Building IT components. Cross referencing Within the text: - Worksection titles are indicated by Italicised text. - Clause titles are indicated by Bold text. 1.3 REFERENCED DOCUMENTS Contractual relationships General: Responsibilities and duties of the principal, contractor and contract 0171 GENERAL REQUIREMENTS 1 TỔNG QUAN 1.1 QUYỀN ƯU TIÊN Ưu tiên Tồng quát: Các yêu cầu nêu trong các chương sau của “Yêu cầu Kỹ Thuật” này có quyền ưu tiên cao hơn nếu có khác biệt. Phiên bản tiếng Anh có quyền ưu tiên cao hơn nêu có khác biệt với phiên bản tiếng Việt. 1.2 THAM CHIẾU Yêu cầu chung - Phù hợp với những Các chương có liên quan sau đây: - Chất kết dính, trám trét và ốc vít. - Chống cháy lan. - Kim loại và xử lý bề mặt kim loại. -Chống Mối. - Xử lý và hoàn thiện bề mặt gỗ. -Phần mềm. . Tham chiếu chiếu chéo Trong văn bản: - Tiêu đề chương được thể hiện bằng chữ in nghiêng. - Tiêu đề các điều khoản thể hiện bằng chữ đậm. 1.3 TÀI LIỆU THAM CHIẾU Mối quan hệ giữa các nhà thầu Tổng quan: Trách nhiệm và nghĩa v của các nhà thầu chính, ph và quản lý dự án không GENERRAL GOLDEN ISLAND Project © VHT Engineering 31 Aug-11 administrator are not altered by requirements in the documents referenced in this specification. Current editions General: Use referenced documents which are the editions, with amendments, current 3 months before the closing date for tenders, except where other editions or amendments are required by statutory authorities. 1.4 INTERPRETATION Abbreviations General: For the purposes of this contract the abbreviations given below apply. - TCVN: VietNam Standard. - AS: Australian Standard. - MS: Mild steel. - MSDS: Material safety data sheets. - NATA: National Association of Testing Authorities. - NZS: New Zealand Standard. - PCA: Plumbing Code of Australia. - SS: Stainless steel. - VOC: Volatile organic compound. Definitions General: For the purposes of this contract the definitions given below apply. - Attendance: ‘Attendance’, ‘provide attendance’ and similar expressions mean ‘give assistance for examination and testing’. - Contract administrator: ‘Contract administrator’ has the same meaning as ‘architect’ or ‘superintendent’ and is the person appointed by the ‘owner’ or ‘principal’ under the contract. - Default: Specified value, product or installation method which is to be provided unless otherwise documented. - Design life: The period of time for which it is assumed, in the design, that an asset will be able to perform its intended purpose with only anticipated maintenance but no major repair or replacement being necessary. - Documented: ‘Documented’, ‘as documented’ and similar terms mean contained in the contract documents. - Economic life: The period of time from the acquisition of an asset to when the asset, while still physically capable of fulfilling its function and with only anticipated maintenance, ceases to be the lowest cost alternative for satisfying that function. - Geotechnical site investigation: The process of evaluating the geotechnical b! thay đổi do yêu cầu trong “Yêu cầu Kỹ Thuật” (YCKT) này. . Phiên bản sủ dng Tổng quát: Sử dng những phiên bản mới nhất trong vòng 3 tháng trước ngày đóng thầu, tr" trư#ng hợp các phiên bản khác được yêu cầu của cơ quan ch$c trách. 1,4 GIẢI THÍCH Chữ viết t%t Tổng thể: Các t" viết t%c sau đây áp dng trong YCKT này. - TCVN: Tiêu chu&n Việt Nam. - AS: Tiêu chu&n Úc. - MS: thép đen. - MSDS: Phiếu ch$ng nhận vật liệu an toàn. - Nata: Hiệp hội Kiểm tra Quốc gia . - NZS: New Zealand Standard. - PCA: Tiêu chu&n Hệ thống cấp thoát nước của Úc. - SS: thép không r'. - VOC: hợp chất hữu cơ d( bay hơi. Định nghĩa Tổng thể: các đ!nh nghĩa đưa ra dưới đây áp dng trong YCKT này. - Tham dự: "Tham dự", "tham gia" và những t" tương tự có nghĩa là "cung cấp trợ giúp trong công tác kiểm tra và thử nghiệm. - Quản lý dự án(QLDA): "Quản lý dự án 'có ý nghĩa giống như" kiến trúc sư "hay" giám đốc dự án" là ngư#i được chủ đầu tư bổ nhiệm theo hợp đồng. - Mặc đ!nh: Ch' đ!nh giá tr! cài đặt, vật tư thiết b! hoặc phương pháp thi công s) được cung cấp, tr" trư#ng hợp khác do YCKT nêu ra. - Tuổi th* theo thiết kế: khoảng th#i gian giả đ!nh theo thiết kế, để thiết b!/ hệ thống có thể hoạt động bình thư#ng với các chế độ bảo trì bình thư#ng, không cần thiết sửa chữa lớn hoặc thay thế . - Tài liệu: "Tài liệu", "như tài liệu" và thuật ngữ tương tự có nghĩa là toàn bộ các tải liệu thiết kế nêu trong hợp đồng. - Tuổi th* kinh tế: khoảng th#i gian khi mua các thiết b! / hệ thống cho đến khi các thiết b! / hệ thống này v+n có thể hoạt động bình thư,ng với chi phí bảo trì thấp. - Khảo sát đ!a chất: Quá trình khảo sát đ!a chất tại công trư#ng. GENERRAL GOLDEN ISLAND Project © VHT Engineering 32 Aug-11 characteristics of the site in the context of existing or proposed construction. - Give notice: ‘Give notice’, ‘submit’, ‘advise’, ‘inform’ and similar expressions mean ‘give notice (submit, advise, inform) in writing to the contract administrator’. - Hold point: The activity cannot proceed without the approval of the contract administrator. - IP: ‘IP’, ‘IP code’, ‘IP rating’ and similar expression have the same meaning as ‘IP Code’ in AS 60529. - Maintenance period: Synonymous with ‘Defects liability period’. - Obtain: ‘Obtain’, ‘seek’ and similar expressions mean ‘obtain (seek) in writing from the contract administrator’. - Metallic-coated: Steel coated with zinc or aluminium-zinc alloy as follows: . Metallic-coated steel sheet: To AS 1397. Metal thicknesses specified are base metal thicknesses. . Ferrous open sections zinc coated by an in-line process: To AS/NZS 4791. . Ferrous hollow sections zinc coated by a continuous or specialised process: To AS/NZS 4792. - Pipe: Includes pipe and tube. - Principal: ‘Principal’ has the same meaning as ‘owner’, ‘client’ and ‘proprietor’ and is the party to whom the Contractor is legally bound to construct the works. - Proprietary: ‘Proprietary’ means identifiable by naming manufacturer, supplier, installer, trade name, brand name, catalogue or reference number. - Provide: ‘Provide’ and similar expressions mean ‘supply and install’ and include development of the design beyond that documented. - Registered testing authority: . An organisation registered by the National Association of Testing Authorities (NATA) to test in the relevant field; or . An local organisation registered by an authority recognised by NATA through a mutual recognition agreement; or . An organisation recognised as being a Registered Testing Authority under legislation at the time the test was undertaken. - Required: Means required by the documents, the local council or statutory authorities. - If required: A conditional specification term for work which may be shown in the documents or be a legislative requirement. - Samples: Includes samples, prototypes and sample panels. - Supply: ‘Supply’, ‘furnish’ and similar expressions mean ‘supply only’. - Tests: - Thông báo: "Thông báo", "đệ trình", "đề ngh!", "thông tin" những t" tương tự có nghĩa là "đưa ra thông báo (đệ trình, đề ngh!, thông báo) bằng văn bản cho QLDA. - Điểm mốc: Hoạt động không thể tiến hành mà không có sự chấp thuận của QLDA. - IP: "cấp IP", "mã IP “ và tương tự có cùng một nghĩa là" tiêu chu&n IP trong AS 60529. - Th#i gian bảo trì: đồng nghĩa với 'Th#i gian sửa chữa sai sót'. - Được th-a thuận: "Được th-a thuận", "đuợc chấp thuận" và những t" tương tự có nghĩa là được QLDA chấp thuận bằng văn bản. - B*c Kim loại: thép tráng k)m hay hợp kim nhôm-k)m, như sau: . Thép tấm b*c kim loại: th-a AS 1397: Quy đ!nh độ dày kim loại . . Thép hình mạ k)m theo tiêu chu&n AS / NZS 4791. . .ng S%t mạ k)m trong một qui trình đặc biệt theo AS / NZS 4792. - .ng: Bao gồm các ống và ống túp. - Giám đốc dự án: 'Giám đốc dự án' có ý nghĩa giống như 'chủ đầu tư', 'bên A' và 'chủ nhà' và là bên mà Nhà thầu là ràng buộc pháp lý để xây dựng công trình. - Ch' đ!nh: 'ch' đ!nh' có nghĩa là ch' đ!nh tên nhà sản xuất, nhà cung cấp, ngư#i l%p đặt, tên thương mại, tên thương hiệu, catalogue hoặc mã sản ph&m. - Cung cấp: "Cung cấp và những t" tương tự có nghĩa là 'cung cấp và l%p đặt' và bao gồm thiết kế bổ sung cho tài liệu này. - Cơ quan Đăng kiểm: o Một tổ ch$c được đăng ký b,i Hiệp hội NATA để kiểm tra trong lĩnh vực liên quan; hay o Một tổ ch$c trong nước được ủy quyền của NATA ; hay o Một tổ ch$c Kiểm đ!nh hợp pháp tại th#i điểm thực hiện thử nghiệm. - Yêu cầu: Những yêu cầu của tài liệu này, chính quyền đ!a phương hay nhà ch$c trách. - Nếu yêu cầu : Một điều kiện thực hiện công việc nêu trong tài liệu này hay là một yêu cầu pháp luật. - M+u : Bao gồm m+u, nguyên m+u và bảng m+u. - Cung cấp : ‘Cung cấp’, ‘cung $ng’ và những t" tương tự có nghĩa‘ch' cung cấp, không l%p đặt. - Thử nghiệm: GENERRAL GOLDEN ISLAND Project © VHT Engineering 33 Aug-11 . Pre-completion tests: Tests carried out before completion tests. * Type tests: Tests carried out on an item identical with a production item, before delivery to the site. * Production tests: Tests carried out on a purchased item, before delivery to the site. * Site tests: Tests carried out on site. . Completion tests: Tests carried out on completed installations or systems before the date for practical completion, to demonstrate that the installation or system, including components, controls and equipment, operates correctly, safely and efficiently, and meets performance and other requirements. The superintendent may direct that completion tests be carried out after the date for practical completion. - Tolerance: The permitted difference between the upper limit and the lower limit of dimension, value or quantity. - Verification: Provision of evidence or proof that a performance requirement has been met or a default exists. - Witness points: Provides an opportunity to attend an activity but does not involve an obligation. The activity can proceed without approval from the contract administrator. 1.5 CONTRACT DOCUMENTS Services diagrammatic layouts General: Layouts of service lines, plant and equipment shown on the drawings are diagrammatic only, except where figured dimensions are provided or calculable. Before commencing work: - Obtain measurements and other necessary information. - Coordinate the design and installation in conjunction with all trades. Levels General: Spot levels take precedence over contour lines and ground profile lines. 1.6 PERFORMANCE General General: If required, provide structures, installations and components as follows: - Fixed access ways: To AS 1657. - Structural design actions: To AS/NZS 1170.0 and the Structural design actions schedule. 1.7 NOTICE . Thử nghiệm trước khi hoàn thành: Các thử nghiệm sau được thực hiện trước khi thử nghiệm hoàn tất. * Type test: Thực hiện thử nghiệm trên thiết b! giống với thiết b! sản xuất, trước khi giao tới công trư#ng. * Thử nghiệm trong sản xuất: Thử được thực hiện trên thiết b! được đặt hàng, trước khi sự giao hàng tới công trư#ng. * Thử tại công trư#ng: Thử được thực hiện tại công trư#ng. . Thử nghiện hoàn thành: Thử nghiệm được thực hiện trên hệ thống đã hoàn tất l%p đặt hay trên những hệ thống trước khi chạy thử, để xác đ!nh hệ thống, bao gồm các cấu kiện, hệ thống điều khiển và thiết b! vận hành chính xác, an toàn và hiệu quả và đáp $ng yêu cầu vận hành và các yêu cầu khác. Giám sát có thể yêu cầu công tác thử nghiệm Hoàn thành được thực hiện sau khi chạy thử. - Độ chính xác: Cho phép có khác nhau giữa giới hạn trên (cận trên) và giới hạn dưới (cận dưới) của kích thước, giá tr! hay số lượng. - Xác nhận: cung cấp bằng ch$ng hay ch$ng minh các yêu cầu đã được thực hiện đầy đủ hay các hư h-ng đã được sửa chữa. - Th#i điểm ch$ng kiến: thông báo th#i gian tham dự một hoạt động không b%t buộc. Các hoạt động có thể tiến hành mà không có sự chấp thuận của QLDA. 1.5 TÀI LIỆU THẦU Bản vẽ nguyên lý Tổng thể: Bản v) mặt b/ng bố trí thiết b!, hướng tuyến ch' thể hiện dạng sơ đồ, tr" trư#ng hợp các v! trí kích thước hình h*c được cung cấp hoặc có thể tính toán trước được. Trước khi thi công: - Đo lư#ng và thu thập thông tin cần thiết. - Phối hợp bản v) thiết kế và phương pháp l%p đặt với tất cả các nhà thầu khác. Cao trình Tổng thể: Lấy mực cao trình theo những đư#ng đồng m$c và cao trình sàn trệt. 1.6 SỰ THỰC HIỆN Tổng thể Tổng quan: Nếu được yêu cầu, cung cấp kết cấu l%p đặt và những ph kiện như đi theo sau.sau: - Cửa kiểm tra cố đ!nh: theo AS 1657. - 0nh hư,ng kết cấu công trình: theo NZS 1170.0 và lập bản kê các tải tr*ng tác động lên kết cấu. GENERRAL GOLDEN ISLAND Project © VHT Engineering 34 Aug-11 Inspection Concealment: If notice of inspection is required in respect of parts of the works that are to be concealed, advise when the inspection can be made before concealment. Minimum notice for inspections to be made: Conform to the Notices schedule. Light level requirements: to AS 1680.2.4. Submissions Proposed products schedules: If major products are not specified as proprietary items, submit a schedule of those proposed for use within 3 weeks of site possession. Tests General: Give notice of the time and place of nominated tests. Minimum notice for witnessing of tests to be made: Conform to the Notices schedule. Attendance General: Provide attendance for inspection and tests. 1.8 SUBMISSIONS General Default timing: Make submissions at least 5 working days before ordering products for, or starting installation of, the respective portion of the works. Authorities Authorities’ approvals: Submit documents showing approval by the authorities whose requirements apply to the work. Correspondence: Submit copies of correspondence and notes of meetings with authorities whose requirements apply to the work. Hard copy submissions Quantity: 02 copies. Errors General: If a submission contains errors, make a new or amended submission as appropriate, indicating changes made since the previous submission. Identification General: Identify the project, contractor, subcontractor or supplier, manufacturer, applicable product, model number and options, as appropriate and include pertinent contract document references. Include service connection requirements and product certification. Identify proposals for non-compliance with project requirements, and characteristics which may be detrimental to successful performance of the completed work. Inspection and testing plan General: Submit an inspection and testing plan which is consistent with the construction program. Include particulars of test stages and procedures. 1.7 CHÚ Ý Kiểm tra Hệ thống đi âm/ngầm: Nếu có yêu cầu thông báo để kiểm tra các hệ thống đi ngầm, nhà thầu phải thông báo trước khi lấp đất / đổ bê tông che kín. Th#i gian thông báo tối thiểu cho giám sát: Phù hợp với bảng kế hoạch thông báo Độ sáng yêu cầu: theo AS 1680.2.4. Đệ trình Đệ trình danh sách thiết b!: Nếu thiết b! chính không quy đ!nh như thiết b! ch' đ!nh, trình của những đề xuất thiết b! sử dng trong vòng 3 tuần sau khi xác lập công trư#ng. Kiểm tra .Tổng thể: Thông báo về th#i gian và đ!a điểm thử nghiệm thông thư#ng. . Thông báo tối thiểu cho các thử nghiệm có ch$ng thực: Phù hợp với bảng kế hoạch thông báo. Tham dự Tổng quan: Tham dự công tác kiểm tra và thử nghiệm. 1.8 Đệ trình Tổng thể Th#i gian mặc đ!nh : Trình ít nhất 5 ngày làm việc trước khi đặt hàng các sản ph&m, hoặc khi b%t đầu l%p đặt các phần riêng biệt của công việc. Nhà chức trách. Việc chấp thuận của nhà ch$c trách: Trình tài liệu cho thấy đáp $ng các yêu cầu của cơ quan th&m quyền. Thư hồi âm: Trình bản sao biên bản h*p, thư hồi âm cho thấy đáp $ng các yêu cầu của cơ quan th&m quyền. Đệ trình hard copy. Số lượng: 02 bản Lỗi. Tổng quan: nếu b! lỗi trong hồ sơ đệ trình phải làm lại hay hiệu ch'nh, có ch' rõ các thay đổi so với hồ sơ trước đây.. Xác nhận Tổng quan: Xác nhận công trình, nhà thầu, thầu ph, nhà cung cấp, nhà sản xuất, sản ph&m, số model sản ph&m, các tùy ch*n thêm của thiết b! / hệ thống phù hợp với hồ sơ thầu. Bao gồm những yêu cầu đầu nối và ch$ng ch' sản ph&m. Xác đ!nh những đề ngh! không tương thích với những yêu cầu của dự án và những đặc trưng nào có thể ảnh hư,ng đến việc hoàn tất dự án.. GENERRAL GOLDEN ISLAND Project © VHT Engineering 35 Aug-11 Test reports: Submit written reports on nominated tests. Materials and components Product certification: If products must conform to product certification schemes, submit evidence of conformance. Product data: For proprietary equipment, submit the manufacturer’s product data as follows: - Technical specifications and drawings. - Type-test reports. - Performance and rating tables. - Recommendations for installation and maintenance. - Additional product data for services equipment: . SET NATSPEC2003M7 - 9333 Model name, designation and number. . Country of origin and manufacture. . Capacity of all system elements. . Size, including required clearances for installation. . Materials used in the construction. Substitution Identified proprietary items: Identification of a proprietary item does not necessarily imply exclusive preference for the item so identified, but indicates the necessary properties of the item. Performance: Equal to or greater than that specified. Alternatives: If alternatives to the documented products, methods or systems are proposed, submit sufficient information to permit evaluation of the proposed alternatives, including the following: - Evidence of conformity to a cited standard. - Samples. - Essential technical information, in English. - Reasons for the proposed substitutions. - Statement of the extent of revisions to the contract documents. - Statement of the extent of revisions to the construction program. - Statement of cost implications including costs outside the contract. - Statement of consequent alterations to other parts of the works. Evidence: If the documented products or systems are unavailable within the time constraints of the construction program. Criteria: If the substitution is for any reason other than unavailability, that the substitution: Kế hoạch kiểm tra và thử nghiệm . Tổng quan: trình kế hoạch kiểm tra, thử nghiệm phù hợp với tiến độ xây dựng. Bao gồm các chi tiết của giai đoạn thử nghiệm và qui trình thử nghiệm. Báo cáo: gửi báo cáo bằng văn bản. Vật tư và cấu kiện. Ch$ng ch' sản ph&m: Trình bằng ch$ng cho thấy sản ph&m phù hợp ch$ng ch' sản ph&m. Thông số sản ph&m: trình các thông số của sản ph&m của nhà sản xuất như sau. - Những đặc tả kỹ thuật và những bản v). - Những báo cáo thử nghiệm type-test. - Hiệu suất và hạng m$c. - Những khuyến cáo l%p đặt và bảo trì. - Thông số thiết b! : . Model và số seri. . Nước xuất kh&u và nuớc sản xuất.. . Công suất m*i phần tử trong hệ thống. . Kích thước, bao gồm những khoảng cách l%p đặt yêu cầu. . Nguyên liệu được dùng trong chế tạo. Thay thế Hạng mc thích hợp đã được xác đ!nh: Xác đ!nh hạng mc thích hợp không ng ý loại tr" hạng mc tốt hơn hạng mc xác đ!nh, mà ch' xác đ!nh thuộc tính của hạng mc. Thực hiện: Bằng hay cao hơn so với YCKT. Thay thế: Nếu đề xuất thay thế thiết b!, phương pháp hay hệ thống trong hồ sơ thầu, phải trình thông tin đủ để có thể đánh giá giải pháp thay thế, bao gồm : - Ch$ng minh giải pháp thay thế phù hợp với tiêu chu&n áp dng. - Trình m+u. - Thông tin kỹ thuật quan tr*ng, bằng tiếng Anh.. - Những lý do cho đề xuất thay thế.. - Đánh giá phạm vi thay đổi hồ sơ thầu. - Đánh giá phạm vi thay đổi tiến độ xây dựng. - Đánh giá thay đổi chi phí bao gồm những chi phí bên ngoài hợp đồng. - Đánh giá thay đổi tác động lên những công việc khác. Bằng ch$ng: Nếu thiết b! hay hệ thống nêu trong hồ sơ thầu không có s1n trong th#i gian xây dựng. GENERRAL GOLDEN ISLAND Project © VHT Engineering 36 Aug-11 - Is of net enhanced value to the principal. - Is consistent with the contract documents and is as effectual as the identified proprietary item. Samples Submission: Submit nominated samples. Incorporation of samples: If it is intended to incorporate samples into the works, submit proposals. Incorporate samples in the works which have been endorsed for incorporation. Do not incorporate other samples. Retention of samples: Keep endorsed samples in good condition on site, until practical completion. Shop drawings General: If required, submit dimensioned drawings showing details of the fabrication and installation of services and equipment, including relationship to building structure and other services, cable type and size, and marking details. Diagrammatic layouts: Coordinate work shown diagrammatically in the contract documents, and submit dimensioned set-out drawings. Checking: Ensure that the drawings have been checked before submission. 1.9 DESIGN General Design by contractor: If the contractor provides design, use only appropriately qualified persons and comply with all statutory requirements. Conflict with the documents: If it is believed that a conflict exists between statutory requirements and the documents, notify the contract administrator immediately and provide a recommendation to resolve the conflict. 2 PRODUCTS 2.1 GENERAL Manufacturers’ or suppliers’ recommendations Provide, including select, if no selection is given, transport, deliver, store, handle, protect, finish, adjust and prepare for use, manufactured items in accordance with the current written recommendations and instructions of the manufacturer or supplier. Proprietary items/systems/assemblies: Assemble, install or fix to substrate in accordance with the current written recommendations and instructions of the manufacturer or supplier. Project modifications: Advise of activities that supplement, or are contrary to, Tiêu chí: Nếu có thay thế do bất k2 lý do nào khác lí do không khả thi, thì: - Là gia tăng giá tr! . - Phù hợp với hồ sơ thầu và có hiệu quả so với hạng mc thích hợp xác đ!nh. Mẫu. Đệ trình: Đệ trình m+u được ch' đ!nh. Thống nhất m+u: Nếu dự đ!nh thống nhất m+u với các công việc, trình đề ngh!. Thống nhất các m+u trong các công việc mà đã được chấp thuận cho thống nhất. Không thống nhất những m+u khác.. Duy trì m+u: Giữ những m+u đã được chấp thuận trong tình trạng tốt tại công trư#ng, cho đến khi hoàn tất công việc. Bản vẽ chế tạo Tổng quát: Nếu cần thiết, trình bản v) chi tiết chế tạo, l%p đặt các hệ thống và trang thiết b!, bao gồm cả liên kết với kết cấu xây dựng và d!ch v khác, loại cáp và kích thước cáp, các chi tiết đánh dấu. Mặt bằng nguyên lý: công tác phối hợp là tất yếu trong hợp đồng thầu , trình những bản v) thể hiện kích thước. Kiểm tra: Bảo đảm rằng những bản v) đã được kiểm tra trước khi trình. 1.9 THIẾT KẾ. Tổng thể Thiết kế b,i nhà thầu: Nếu nhà thầu cung cấp thiết kế, ch' sử dng cán bộ phù hợp, có đủ tiêu chu&n và tuân thủ m*i yêu cầu theo luật.. Khác biệt với thiết kế: Nếu có cuộc khác biệt giữa yêu cầu luật đ!nh và thiết kế, thông báo cho QLDA ngay lập t$c và trình kiến ngh! để giải quyết khác biệt. 2 THIẾT BỊ 2.1 TỔNG THỂ Khuyến cáo của nhà cung cấp Cung cấp, bao gồm lựa ch*n, nếu không có ch' đ!nh, vận chuyển, cung cấp, lưu trữ, xử lý, bảo vệ, hoàn thiện, hiệu ch'nh và chu&n b! để sử dng, thiết b! sản xuất phù hợp với các khuyến cáo và hướng d+n hiện hành bằng văn bản của nhà sản xuất hoặc nhà cung cấp. Hạng mc thích hợp/ những hệ thống/ thiết b! hợp bộ : L%p ráp, l%p đặt hay cố đ!nh vào kết GENERRAL GOLDEN ISLAND Project © VHT Engineering 37 Aug-11 manufacturer’s or suppliers’ written recommendations and instructions. Sealed containers General: If materials or products are supplied by the manufacturer in closed or sealed containers or packages, bring the materials or products to point of use in the original containers or packages. 2.2 TESTS Attendance General: Provide attendance on tests. Testing authorities General: Except for site tests, have tests carried out by a Registered testing authority and submit test reports. - Reports: Submit copies of test reports, including certificates for type tests, showing the observations and results of tests and conformance or non-conformance with requirements. - Site tests: Use instruments calibrated by authorities accredited by a Registered testing authority. 2.3 MATERIALS AND COMPONENTS Consistency General: For each material or product use the same manufacturer or source and provide consistent type, size, quality and appearance. Corrosion resistance General: Conform to the following corrosivity category with regard to worksection corrosion resistance tables. Situation The following classification of situation applies to tables in the worksection corrosion resistance tables. - Internal: . Building fabric protected from salt and moisture by vapour barriers, sarking, sheathing and building wraps. - External: . Includes external leaf and air spaces behind external leaf brickwork or blockwork walls. Galvanizing Severe conditions: Galvanize mild steel components (including fasteners) to AS 1214 or AS/NZS 4680 as appropriate, if: - Exposed to weather. cấu công trình phải theo những khuyến cáo hiện th#i ghi bằng văn bảng và những ch' d+n của nhà sản xuất hay cung cấp. Hiệu ch'nh dự án: Tư vấn những tác động ph, hoặc trái ngược với khuyến cáo của nhà cung cấp và sản xuất. Bao bì Tổng quát: Nếu vật liệu hoặc sản ph&m được cung cấp b,i các nhà sản xuất trong thùng kín hoặc bao bì, gữi nguyên vật liệu hoặc thiết b! cho đến khi sử dng trong các thùng ch$a hoặc bao bì ban đầu. 2.2 Kiểm tra Tham dự. Tổng quan: Tham gia các thử nghiệm. Cơ quan chuyên trách Thử nghiệm. - Tổng quan: Ngoại tr" thử nghiệm tại công trư#ng, có những thử nghiệm được thực hiện b,i cơ quan chuyên trách về thử nghiệm và trình những báo cáo thử nghiệm. - Báo cáo: đệ trình bản sao các báo cáo thử nghiệm, kể cả những ch$ng ch' thử Type test, cho thấy các quan sát và kết quả của những thử nghiệm phù hợp hay không phù hợp với những yêu cầu. - Thử nghiệm tại công trư#ng: Sử dng thiết b! đo đã được kiểm đ!nh b,i một cơ quan chuyên trách. 2.2 VT TƯ VÀ C!U KIỆN Th"ng nhất Tổng quan: Đối với mỗi vật tư hay thiết b! cùng nhà sản xuất hay nhà cung cấp, cung cấp kiểu, kích thước, chất lượng và v3 ngoài như nhau. Ch"ng #n mòn Tổng quan: cấp chống ăn mòn phù hợp với chương chống ăn mòn. Địa $iểm Việc phân loại sau đây áp dng theo các bảng trong chương chống ăn mòn. - Trong nhà. . Xây dựng cơ chế bảo vệ chống lại ăn mòn của muối và độ &m b,i màn, tấm ốp, màng b*c và tấm phủ chống &m. - Ngoài nhà Bao gồm lớp hoàn thiện và không khí giữa lớp hoàn thiện và tư#ng gạch hay tư#ng gạch block. Tráng kẽm Điều kiện đặc biệt: Cấu kiện bằng thép tráng k)m (bao gồm các chi tiết treo, móc) theo tiêu GENERRAL GOLDEN ISLAND Project © VHT Engineering 38 Aug-11 - Embedded in masonry. - Exposed to or in air spaces behind external leaf of masonry walls. - In contact with chemically treated timber, other than CCA. 3 EXECUTION 3.1 WALL CHASING Holes and chases General: If holes and chases are required in masonry walls, provide proposals to demonstrate that the structural integrity of the wall is maintained. Do not chase walls nominated as fire rated or acoustic. Parallel chases or recesses on opposite faces of a wall shall not be closer than 600 mm to each other. Chasing of blockwork: Only in core-filled hollow blocks or in solid blocks which are not designated as structural and shall be to the Concrete blockwork chasing table. Concrete blockwork chasing table Block thickness ( mm) Depth of chase (maximum mm) 190 35 140 25 90 20 3.2 FIXING General Suitability: If equipment and services are not suitable for fixing to non-structural building elements, fix directly to structure and trim around penetrations in non-structural elements. Fasteners Use proprietary fasteners capable of transmitting the loads imposed, and sufficient to ensure the rigidity of the assembly. 3.3 COMPLETION Samples General: Remove unincorporated samples on completion. Warranties General: If a warranty is documented or if a manufacturer’s standard warranty extends beyond the end of the defects liability period, name the principal as warrantee . Register with manufacturers as necessary. Retain copies delivered with components and equipment. ch&n AS 1214 hay AS/ NZS 4680 thích hợp, nếu: - Để ngoài tr#i. - Âm trong vữa. - Tiếp xúc với không khí sau lớp hoàn thiện của tư#ng gạch - Tiếp xúc với Hóa chất xử lý gỗ làm nhà, khác với CCA. 3. Thực hiện. 3.1 C%t tư&ng. Khoan c%t tư&ng Tổng quan: Nếu cần khoan c%t tư#ng xây tô, cung cấp những đề ngh! gia cố cấu trúc (của) tư#ng. Không được khoan c%t tư#ng chống cháy, cách âm. Rãnh c%t song song cùng mặt hay , 02 mặt tư#ng không được gần nhau quá 600 mm. C%t tư#ng gạch block: Ch' tư#ng gạch block có phun vữa trong lõi hay tư#ng đặc không ch!u lực mới được c%t theo bảng sau: Bảng c%t tư&ng gạch block. B' dày tư&ng( mm) Đ( sâu (maximum mm) 190 35 140 25 90 20 3.2 C) ĐỊNH. Tổng thể Phù hợp: nếu thiết b! và những hệ thống không thích hợp để cố đ!nh vào kết cấu không ch!u lực, cho phép cố đ!nh vào trong kết cấu ch!u lực và vạt cách lỗ m, trên kết cấu không ch!u lực. Cấu kiện treo móc Sử dng cấu kiện treo móc tương thích tải tr*ng thiết b! và g%n ch%c ch%n, an toàn thiết b!. 3.3 HOÀN THÀNH Mẫu Tổng quan: Loại b- những m+u không phù hợp khi hoàn thành l%p đặt. Bảo hành Tổng quát: Nếu bảo hành được nêu trong hồ sơ hoặc nếu bảo hành tiêu chu&n của nhà sản xuất vượt quá th#i gian trách nhiệm sữa chữa, th#i gian trách nhiệm theo th#i gian bảo GENERRAL GOLDEN ISLAND Project © VHT Engineering 39 Aug-11 Commencement: Commence warranty periods at practical completion or at acceptance of installation, if acceptance is not concurrent with practical completion. Approval of installer: If installation is not by manufacturer, and product warranty is conditional on the manufacturer’s approval of the installer, submit the manufacturer’s written approval of the installing firm. 3.4 RECORD DRAWINGS General General: Submit record drawings. Show the ‘as installed’ locations of building elements, plant and equipment. Include ‘as installed’ amendments to shop drawings. Show off-the- grid dimensions where applicable. Date for submission: Within 2 weeks after practical completion. Accuracy Documents: Incorporate all modifications made during the progress of the work and testing period. Show any provisions for the future. Endorsement: Sign and date all record drawings. Keep one set of shop drawings on site at all times expressly for the purpose of marking changes made during the progress of the works. Drawing layout General: Use the same borders and title block as the contract drawings. Quantity and format General: Refer to Submissions. 3.5 OPERATION AND MAINTENANCE MANUALS General General: Submit operation and maintenance manuals for installations. Authors and compilers: Personnel experienced in the maintenance and operation of equipment and systems installed, and with editorial ability. Referenced documents: If referenced documents or technical worksections require that manuals be submitted, include corresponding material in the operation and maintenance manuals. Subdivision: By installation or system, depending on project size. Date for draft submission: 2 weeks prior to commencement of training. Date for final submission: Within 2 weeks after practical completion. Contents hành . Đăng ký bảo hành với các nhà sản xuất nếu cần. Giữ lại bản sao cho các cấu kiện và thiết b!. B%t đầu: B%t đầu bảo hành sau khi nghiệm thu hay sau khi được chấp thuận nếu th#i điểm chấp thuận không trùng với th#i điểm nghiệm thu. Chấp thuận nhà thầu thi công l%p đặt: nếu công tác l%p đặt không thực hiện b,i nhà sản xuất, và sản ph&m bảo hành có điều kiện là ngư#i l%p đặt phải được nhà sàn xuất chấp thuận, phải đệ trình giấp chúng nhận nhà sản xuất chấp thuận nhà thầu thi công l%p đặt . 3.4 Bản vẽ hoàn công. Tổng thể Tổng quan: Đệ trình bản v) hoàn công. Thể hiện v! trí “như l%p đặt” những phần tử, phòng máy và thiết b!. Bao gồm những sự thay đổi so với bản v) shop drawings. Thể hiện lưới cột . Th#i gian đệ trình: trong 2 tuần sau khi nghiệm thu. Chính xác. Tài liệu: Hợp nhất m*i thay đổi trong suốt th#i gian thi công, thử nghiệm. Cho thấy tất cả chu&n b! cho tương lai. Xác nhận: Ký tên, ghi ngày tháng trong tất cả bản v) hoàn công. Giữ một bản v) shopdrawing trong công trư#ng để ghi nhận nhựng thay đổi trong th#i gian thi công. Trình bày. Tổng quan: cùng khung tên như những bản v) trong hợp đồng. S" lư*ng và khuôn dạng. Tổng quan: Tham chiếu tới chương đệ trình. 3.5 Hư+ng dẫn Sử d,ng vận hành và bảo trì Tổng thể Tổng quan: Đệ trình sổ tay vận hành, bảo dư4ng thiết b! những hệ thống l%p đặt. Tác giả và biên tập: Nhân viên có kinh nghiện trong công tác bảo trì và vận hành thiết b! và những hệ thống được l%p đặt, và có khả năng biên soạn. Tài liệu tham khảo: nếu tài liệu tham khảo hay các chương kỹ thuật yêu cầu đệ trình tài liệu hướng d&n, bao gồm vật liệu tương $ng trong vận hành và những sổ tay bảo dư4ng thiết b!. Chia nh-: Theo thiết b! l%p đặt hay hệ thống, ph thuộc kích thước hồ sơ Ngày đệ trình bản phác thảo: 2 tuần trước khi huấn luyện. GENERRAL GOLDEN ISLAND Project © VHT Engineering 40 Aug-11 General: Include the following: - Certificates: . Certificates from authorities. . Copies of manufacturers’ warranties. . Product certification. - Directory: Names, addresses, and telephone and facsimile numbers of principal consultant, subconsultants, contractor, subcontractors and names of responsible parties. - Drawings: . Record drawings, full size. - Drawings and technical data: As necessary for the efficient operation and maintenance of the installation. - Equipment descriptions: . Name, address and telephone and facsimile numbers of the manufacturer and supplier of items of equipment installed, together with catalogue list numbers. . Schedules (system by system) of equipment, stating locations, duties, performance figures and dates of manufacture. Provide a unique code number cross-referenced to the record and diagrammatic drawings and schedules, including spare parts schedule, for each item of equipment installed. - Maintenance procedures: . Detailed recommendations for preventative maintenance frequency and procedures. . Manufacturer’s technical literature as appropriate. Register with manufacturer as necessary. Retain copies delivered with equipment. . Safe trouble-shooting, disassembly, repair and reassembly, cleaning, alignment and adjustment, balancing and checking procedures. Provide logical step-by-step sequence of instructions for each procedure. . Schedule of spares recommended to be held on site, being those items subject to wear or deterioration and which may involve the principal in extended deliveries when replacements are required. Include complete nomenclature and model numbers, and local sources of supply. - Maintenance records: . Documentation to AS 1851 clause 18.2.5. - Operation procedures: . Manufacturers’ technical literature as appropriate. - Table of contents: For each volume. Title to match cover. Ngày đệ trình chính th$c: Trong 2 tuần sau khi nghiệm thu. N(i dung Tổng quan: Bao gồm: - Ch$ng ch' . Ch$ng ch' t" những nhà ch$c trách . Bản sao phiếu bảo hành của nhà sản xuất.. . Ch$ng ch' chất lượng Sản ph&m. - Thư mc: Tên, đ!a ch', điện thoại và số fax tư vấn chính/ ph, nhà thầu, thầu ph và các bên tham gia ch!u trách nhiệm. - Bản v): Bản v) hoàn công, khổ lớn nhất. - Bản v) và số liệu kỹ thuật: cần thiết cho vận hành, bảo trì hệ thống hiệu quả. Mô tả Thiết b!:. . Tên, đ!a ch' và điện thoại và số fax của nhà sản xuất và nhà cung cấp các hạng mc thiết b! l%p đặt, cùng với số danh mc catalogue. . Đặc tính thiết b! (t"ng hệ thống),v! trí, tải, đặc tuyến vận hành và ngày sản xuất. Qui đ!nh mã số thống nhất suốt hồ sơ, bản v) hoàn công và đăc tính kỹ thuật , bao gồm đặc tính ph tùng thay thế, mỗi hạng mc thiết b! l%p đặt... Qui trình bảo trì: . Nêu rõ khuyến cáo tần suất bảo trì và biện pháp phòng ng"a. . Phát hành tài liệu kỹ thuật cho phù hợp. Đăng ký với nhà sản xuất khi cần thiết. Giữ lại bản sao theo kèm trang thiết b!. . Qui trình phát hiện hư h-ng và biên pháp kiểm tra an toàn, tháo l%p, sửa chữa và làm vệ sinh, cân ch'nh và hiệu ch'nh, cân bằng và kiểm tra. Cung cấp hướng d+n t"ng bước một cho mỗi qui trình. . Danh mc ph tùng được khuyến cáo dự trữ s1n, phù hợp với hao mòn hay hư h-ng và th#i gian giao hàng khi cần thay thế. Bao gồm danh mc và những số model và nhà cung cấp đại phương. Sổ tay Bảo trì:. . Như AS 1851 chương 18.2.5. Qui trình vận hành . Sổ tay kỹ thuật của nhà sản xuất thích hợp. GENERRAL GOLDEN ISLAND Project © VHT Engineering 41 Aug-11 Format – electronic copies Printing: Provide material that can be legibly printed on A4 size paper. Scope: Provide the same material as specified for hardcopy in electronic format. Quantity and format: Refer to Electronic submissions. Format – hard copy General: A4 size loose leaf, in commercial quality, 4 ring binders with hard covers, each indexed, divided and titled. Include the following features: - Cover: Identify each binder with typed or printed title ‘OPERATION AND MAINTENANCE MANUAL’, to spine. Identify title of project, volume number, volume subject matter, and date of issue. - Dividers: Durable divider for each separate element, with typed description of system and major equipment components. Clearly print short titles under laminated plastic tabs. - Drawings: Fold drawings to A4 size and accommodate them in the binders so that they may be unfolded without being detached from the rings. Provide with reinforced punched binder tabs. - Pagination: Number pages. - Ring size: 50 mm maximum, with compressor bars. - Text: Manufacturers’ printed data, including associated diagrams, or typewritten, single-sided on bond paper, in clear concise English. Number of copies: 3. 3.6 CLEANING Final cleaning General: Before practical completion, clean throughout, including all exterior and interior surfaces except those totally and permanently concealed from view. Labels: Remove all labels not required for maintenance. 3.7 POST-CONSTRUCTION MANDATORY INSPECTIONS AND MAINTENANCE General General: For the duration of the defects liability period, provide inspections and maintenance of safety measures required by the following: - The Building Code of Australia. - AS 1851. - Other statutory requirements applicable to the work. Records: Provide mandatory records. Nội dung: Đối với mỗi hồ sơ, ghi tiêu đề để phù hợp với bìa. Định dạng – file m'm. In ấn:cung cấp file có thể được in ấn trên giấy kích thước A4. Phạm vi: Cung cấp file cùng đ!nh dạng như được ch' rõ cho bản in trong mềm. Số lượng và đ!nh dạng: Tham chiếu tới chương $ệ trình file m'm. Định dạng - Bản cứng. Tổng quan: kích thước A4 t# đơn, chất lượng thương mại, k5p bấm 4 lỗ với trang bìa, danh mc, phân trang và tiêu đề. Bao gồm những đặc tính sau đây: - Trang bìa: Xác đ!nh t"ng hồ sơ bằng tiêu đề in trên cạnh hồ sơ ' Sổ tay Thao tác và bảo dư4ng thiết b!'. Xác đ!nh tên dự án, số tập, tên tập và ngày ký phát. - Phân trang: Phân trang cho mỗi chương riêng biệt với mô tả hệ thống và những thành phần thiết b! chính. In ấn rõ ràng ng%n g*n các tiêu đề và ép plastic. - Bản v): Gấp kích thước A4 và g%n trong hồ sơ sao cho nó có thể m, ra không cần tách r#i ra kh-i k5p hồ sơ. Cung cấp dải băng tăng cư#ng cho gáy đc lỗ. - Phân trang: Đánh số trang. - Kích thước vòng k5p giấy: 50 mm cực đại, với những thanh ép giấy. - Văn bản: Thông tin in của nhà sản xuất, kể cả những sơ đồ liên quan, hay được đánh máy, một mặt, trong tiếng Anh ng%n g*n sáng sủa.. - Số lượng bản sao: 3 3.6 D-N D.P VỆ SINH D/n d0p Tổng quan: Trước khi sự nghiệm thu hoàn thành, lau chùi tất cả, bao gồm m*i bề mặt ngoài và phía trong tr" những chi tiết thư#ng xuyên bi che khuất. Nhãn: Loại b- nhãn không được yêu cầu cho việc sự bảo trì. 3.7 Kiểm Tra và Bảo Trì sau bàn giao. Tổng thể Tổng quan: Trong th#i gian bảo hành, kiểm tra và bảo trì theo yêu cầu sau đây. - Luật xây dựng Australia. - Theo AS 1851. - Những yêu cầu theo luật phù hợp với công việc. Biên bản: Cung cấp biên bản ghi chép. GENERRAL GOLDEN ISLAND Project © VHT Engineering 42 Aug-11 Certification: Certify that mandatory inspections and maintenance have been carried out and that the respective items comply with statutory requirements. Submit certification. Annual inspection: Provide an annual inspection and maintenance immediately prior to the end of the defects liability period. Ch$ng ch': Ch$ng nhận rằng công tác kiểm tra và bảo trì đã được thực hiện và tuân theo các tiêu chu&n yêu cầu. Đệ trình ch$ng ch' . Kiểm tra hàng năm: Kiểm tra hàng năm và bảo dư4ng ngay lập t$c trước khi kết thúc bảo hành. GENERRAL GOLDEN ISLAND Project © VHT Engineering 43 Aug-11 181 ADHESIVES, SEALANTS AND FASTENERS 1 GENERAL 1.1 CROSS REFERENCES General General: Conform to the General requirements worksection. 1.2 SUBMISSIONS Installed sealant tests Sampling: For each sealant test take 3 samples of installed and cured sealant, each at least 50 mm long, from completed joints. Testing: Submit the results of tests to the Installed sealant tests schedule. Reinstatement: Make good the joints from which the samples were taken. Sealants Samples: Submit colour samples of visible joint sealants. Documents: Submit technical data sheets. 1.3 INSPECTION Notice Inspection: Give notice so that inspection may be made of joints and penetrations prepared for the application of sealants to the Installed sealant tests schedule. 1.4 PERFORMANCE Adhesives and sealants General: Provide adhesives and sealants capable of transmitting imposed loads, sufficient to ensure the rigidity of the assembly, or integrity of the joint and which will not cause discolouration of finished surfaces. Compatibility: Do not use sealants or adhesives that are incompatible with the products to which they are applied. Movement: Where an adhered or sealed joint may be subject to movement, select a system accredited to accommodate the projected movement under the conditions of service. Refurbishment: Use sealants that can be safely removed and prepared for 181 KEO DÁN, TRÉT KÍN VÀ VT TƯ TREO MÓC. 1 TỔNG THỂ 1.1 NH1NG THAM CHIẾU CHÉO Tổng quan Tổng quan: sự tuân thủ tới chương yêu cầu chung . 1.2 ĐỆ TRÌNH Thử nghiệm keo bịt kín. Lấy m+u: Mỗi loại keo thử 3 m+u trám trét trên các mối nối, mỗi m+u dài ít nhất 50mm. Thử: Cung cấp kết quả thử với Bảng đặc tính thử keo bịt kín. Phc hồi: phc hồi mối nối đã làm thử nghiệm. Keo bịt kín M+u: cung cấp kao màu cho các mối nối trông thấy được. Tài liệu: Cung cấp bảng dữ liệu kỹ thuật. 1.3 KIỂM TRA Chú ý Kiểm tra: Thông báo việc kiểm tra có thể thực hiện trên mối nối và lỗ xuyên có sử dng keo trám trét so với Bảng đặc tính thử keo bịt kín. 1.4 THỰC HIỆN Keo kết dính và keo bịt kín Tổng quan: Cung cấp những keo dính và những keo b!t kín có khả năng ch!u tải tr*ng, bảo đảm hệ thống r%n ch%c, bảo toàn mối nối và không làm thay đổi màu của lớp hoàn thiện bề mặt. Tính Tương thích: Không sử dng những keo kết dính hay b!t kín mà không tương thích với những sản ph&m được sử dng. Chuyển động: Khi keo kết dính hay b!t kín cho mối nối chuyển động, lựa ch*n loại keo phù hợp với chuyển động này trong những điều kiện làm việc bình thư#ng. Nâng cấp: Sử dng chất b!t kín có thể được loại b- một cách an toàn và chu&n b! cho công tác nâng cấp. GENERRAL GOLDEN ISLAND Project © VHT Engineering 44 Aug-11 refurbishment. Fasteners Provide fasteners accredited for the particular use, capable of transmitting imposed loads and maintaining the rigidity of the assembly. 2 PRODUCTS 2.1 ADHESIVES Standards Mastic adhesive: To AS 2329. Polymer emulsion adhesive for timber: To AS 2754.2, not inferior to Type 3. High strength adhesive tape General description: A foam of cross linked polyethylene or closed cell acrylic coated both sides with a high performance acrylic adhesive system, encased in release liners of paper or polyester. Product classification: Ensure product suitability for the following substrates: - Firm high strength foam tapes for high energy surfaces including most bare metals such as stainless steel and aluminium. - Conformable high strength foam for medium energy surfaces including many plastics and paints, and bare metals. - Conformable high strength foam for lower energy surfaces including many plastics, most paints and powder coatings, and bare metals. Thickness: Select the tape to ensure a mismatch between surfaces does not exceed half the tape thickness under the applied lamination pressure. 2.2 SEALANTS Standards General: To ISO 11600. External masonry joints General: Provide sealant and bond breaking backing materials compatible with each other and the substrate and which are non-staining to masonry. Do not use bituminous materials with absorbent masonry units. Bond breaking backing: - Bond breaking materials: Non-adhesive to sealant, or faced with a non-adhering material. - Foamed materials: Closed-cell or impregnated, not water-absorbing. Giá treo/ móc Cung cấp giá treo/ móc thích hợp cho mc đích sử dng, ch!u được tải tr*ng và bảo đảm vững ch%c cho hệ thống được l%p đặt. 2 SẢN PH2M 2.1 KEO DÁN Tiêu chu3n. Keo Mát-tích: Theo AS 2329.. Keo nh6 tương Pôlime cho gỗ: Theo AS 2754.2, không thấp hơn loại 3. B#ng keo kết dính cao. Mô tả Chung: Băng bằng polyethylen liên kết hay phủ nhựa acrylic lên cả hai mặt với keo dính loại nhựa acrylic kết dính cao, quấn trong lớp lót bằng giấy hay polyester. Phân loại sản ph&m: Bảo đảm Sản ph&m phù hợp theo những yêu cầu sau đây: - Băng keo dai bền cho các bề mặt d+n điện tốt bao gồm hầu hết các bề mặt kim loại trần như thép không r' và nhôm. - Băng keo dai m!n cho bề mặt d+n điện trung bình, bao gồm chất d3o, sơn và những kim loại trần. - Băng keo dai m!n cho bề mặt d+n điện kém, bao gồm nhiều chất d3o, đa số sơn dầu và sơn tĩnh điện và kim loại trần. Bề dày: Ch*n lựa Băng keo bảo đảm kích thước các điểm không tiếp xúc của các bề mặt không vượt hơn nửa bề dày băng keo với lực ép kéo thông thư#ng . 2.2 TRÉT KÍN Tiêu chu3n Tổng: theo ISO 11600. M"i n"i tư&ng ngoài nhà Tổng quan: Cung cấp keo trét kín và vật liệu tô trét vết n$t phù hợp l+n nhau và với lớp nền và không khác màu với lớp vữa tô. Không sử dng những vật liệu bitum với những lớp vữa hút nước. Vật liệu tô trét: - Vật liệu tô trét không dính hay bề mặt không dính - Vật liệu foam: loại tổ ong hay t&m, không hút nước. M"i n"i ch"ng cháy GENERRAL GOLDEN ISLAND Project © VHT Engineering 45 Aug-11 Fire rated control joints General: Provide sealant materials that maintain the nominated fire resistant rating. - Fire stopping: To AS 4072.1. Pointing and bedding General: Provide sealants for fast moving joints in light weight building elements that are compatible with the contact materials. Bond breaking backing: - Bond breaking materials: Non-adhesive to sealant, or faced with a non-adhering material. - Foamed materials: Closed-cell or impregnated, not water-absorbing. Floor movement joints General: Provide trafficable sealants for that are compatible with the contact materials. Bond breaking backing: - Bond breaking materials: Non-adhesive to sealant, or faced with a non-adhering material. - Foamed materials: Closed-cell or impregnated, not water-absorbing. 2.3 FASTENERS General Masonry anchors: Proprietary expansion or chemical type. Plain washers: To AS 1237.1. - Provide washers to the heads and nuts of bolts, and the nuts of coach bolts. Plugs: Proprietary purpose-made plastic. Powder-actuated fasteners: To AS/NZS 1873.4. Stainless steel fasteners: To ASTM A240/240M. Steel nails: To AS 2334. - Length: At least 2.5 x the thickness of the member being secured, and at least 4 x the thickness if the member is plywood or building board < 10 mm thick. Unified hexagon bolts, screws and nuts: To AS/NZS 2465. Fasteners in CCA treated timber: Epoxy coated or stainless steel. Bolts Coach bolts: To AS/NZS 1390. Hexagon bolts Grades A and B: To AS 1110.1. Hexagon bolts Grade C: To AS 1111.1. Corrosion resistance Tổng quan: Cung cấp keo chống cháy, cấp chống cháy theo yêu cấp - Fire stop Theo AS 4072.1. Trám kín $iểm và n'n Tổng quan: Cung cấp keo trám kín những mối nối chuyển động nhanh của các kết cấu tr*ng lượng nh5 thích hợp với vât liệu tiếp xúc. Vật liệu tô trét: - Vật liệu tô trét không dính hay bề mặt không dính - Vật liệu foam: loại tổ ong hay t&m, không hút nước. M"i n"i khe co dãn sàn công trình Tổng quan: Cung cấp keo trám kín cho phép đi lại thích hợp với bề mặt tiếp xúc.. Vật liệu tô trét: - Vật liệu tô trét không dính hay bề mặt không dính - Vật liệu foam: loại tổ ong hay t&m, không hút nước. 2.3 PH4 KIỆN TREO MÓC Tổng quan Neo tư#ng xây: loại dãn n, hay hóa chất Lông đền: Theo AS 1237.1.. Cung cấp lông đền , đầu bù long và ốc. Đầu c%m: bằng chất d3o chuyên dùng. Bộ treo sơn tĩnh điện: theo AS / NZS 1873,4. Bộ treo thép không r': Theo ASTM A240/ 240 M.. Đinh thép: Theo AS 2334. - Chiều dài: ít nhất 2.5 x bề dày vật cần cố đ!nh, và tối thiểu 4 x bề dày nếu kết cấu bằng ván ép hay bảng gỗ chiều dày < 10 mm. Bù loong, vít, ốc lc giác: Theo AS / NZS 2465. Bộ treo móc vào gỗ được xử lý: Sơn Epoxi hay thép không r'. Bu lông Bulông m6 chp Theo AS / NZS 1390. Bulông lc giác loại A và B Theo AS 1110.1. Bulông lc giác loại C Theo AS.1111.1. GENERRAL GOLDEN ISLAND Project © VHT Engineering 46 Aug-11 Corrosivity category: high corrosivity category. Steel products: Conform to the Corrosion resistance table or provide proprietary products with metallic and/or organic coatings of equivalent corrosion resistance. Ch"ng cự 5n mòn. Loại chống ăn mòn: loại cao. Sản ph&m thép: Tuân thủ the bảng chống 7n mòn hay cung cấp những sản ph&m chuyên dùng với lớp phủ chống 7n mòn kim loại và/ hoặc hữu cơ tương đương. Corrosion resistance table – low corrosivity category Bảng ch"ng 5n mòn loại thấp. Situation/Địa $iểm Self drilling screws to AS 3566.2 Class Loại Vít tự khoang theo AS 3566.2 Threaded fasteners and anchors/ Neo và b( treo móc Powder actuated fasteners / B( móc treo sơn tĩnh Material Vật liệu Minimum local metallic coating thickness ( µ µµ µm) Độ dày lớp mạ Material grade Loại vật liệu Minimum local coating thickness ( µ µµ µm) Độ dày lớp phủ Internal/ trong nhà 1 Electroplated zinc /mạ k)m điện 4 Electroplated zinc /mạ k)m điện 4 External/ ngoài nhà 3 Electroplated zinc or Hot-dip galvanized /Mạ k)m điện hoặc mạ k)m nhúng nóng 30 Stainless steel /Thép không g' 316 Corrosion resistance table – medium corrosivity category Bảng ch"ng 5n mòn loại trung bình. Internal/ trong nhà Self drilling screws to AS 3566.2 Class Loại Vít tự khoang theo AS 3566.2 Threaded fasteners and anchors/ Neo và b( treo móc Powder actuated fasteners / B( móc treo sơn tĩnh $iện Material Vật liệu Minimum local metallic coating thickness ( µ µµ µm) Độ dày lớp mạ Material grade Loại vật liệu Minimum local coating thickness ( µ µµ µm) Độ dày lớp phủ Internal/ trong nhà 2 Electroplated zinc /mạ k)m điện 12 Electroplated zinc /mạ k)m điện 12 External/ ngoài nhà 4 Electroplated zinc or Hot-dip galvanized /Mạ k)m điện hoặc mạ k)m nhúng nóng 50 Stainless steel /Thép không g' 316 GENERRAL GOLDEN ISLAND Project © VHT Engineering 47 Aug-11 Corrosion resistance table – high corrosivity category Bảng chống 7n mòn loại cao Situation/Địa $iểm Self drilling screws to AS 3566.2 Class Loại Vít tự khoang theo AS 3566.2 loại Threaded fasteners and anchors/ Neo và b( treo móc Powder actuated fasteners / B( móc treo sơn tĩnh $iện Material Vật liệu Minimum local metallic coating thickness ( µ µµ µm) Độ dày lớp mạ Material grade Loại vật liệu Minimum local coating thickness ( µ µµ µm) Độ dày lớp phủ Internal/ trong nhà 3 Electroplated zinc or Hot-dip galvanized /Mạ k)m điện hoặc mạ k)m nhúng nóng 30 Stainless steel /Thép không g' 316 External/ ngoài nhà Stainless steel /Thép không g' 316 Stainless steel 316 Stainless steel /Thép không g' 316 GENERRAL GOLDEN ISLAND Project © VHT Engineering 48 Aug-11 Finishes Electroplating: - Metric thread: to as 1897. - Imperial thread: to as 4397. Galvanizing: - Threaded fasteners: To AS 1214. - Other fasteners: To AS/NZS 4680. Mild steel fasteners: Galvanize if: - Embedded in masonry. - In external timbers. - In contact with chemically treated timber, other than CCA treated timber. Epoxy coated: - CCA Treated timber. Nuts Hexagon chamfered thin nuts Grades A and B: To AS 1112.4. Hexagon nuts Grade C: To AS 1112.3. Hexagon nuts Style 1 Grades A and B: To AS 1112.1. Hexagon nuts Style 2 Grades A and B: To AS 1112.2. Screws Coach screws: To AS/NZS 1393. Hexagon screws Grades A and B: To AS 1110.2. Hexagon screws: Grade C To AS 1111.2. Hexagon socket screws: To AS 1420 and AS/NZS 1421. Machine screws: To AS/NZS 1427. Self-drilling screws: To AS 3566.1 and AS 3566.2. Self-tapping screws: - Crossed recessed countersunk (flat – common head style): to AS/NZS 4407. - Crossed recessed pan: to AS/NZS 4406. - Crossed recessed raised countersunk (oval): to AS/NZS 4408. - Hexagon: to AS/NZS 4402. - Hexagon flange: to AS/NZS 4410. - Hexagon washer: to AS/NZS 4409. - Slotted countersunk (flat – common head style): to AS/NZS 4404. - Slotted pan: to AS/NZS 4403. Hoàn thiện bề mặt Mạ điện: - Ren hệ mét: theo AS 1897. - Ren hệ Anh: theo AS.4397. Mạ k)m: - Bộ treo móc ren răng: Theo AS 1214. - Bộ treo móc khác: Theo AS / NZS 4680. Bộ treo móc bằng thép đen: Mạ k)m nếu : - Đặt trong lớp hồ. - Trong gỗ ngoài nhà. - Khi tiếp xúc với gỗ xử lý hóa h*c, gỗ xử lý khác so với xử lý CCA. Epoxi phủ: - Gỗ xử lý CCA Con "c/tán. Tán lc giác vát cạnh m-ng loại A và B Theo AS 1112.4.. Tán lc giác vát cạnh m-ng loại C Theo AS 1112.3. Tán lc giác vát cạnh m-ng kiểu 1 loại A và B Theo AS. 1112.1. Tán lc giác vát cạnh m-ng kiểu 2 loại A và B Theo AS. 1112.2. Vít. Vít đầu vuông: Theo AS / NZS 1393. Vít lc giác loại A và B Theo AS 1110.2. Vít lc giác loại C Theo AS 1111.2. Vít lc giác âm Theo AS 1420 và NZS 1421. Vít b%t bằng máy Theo AS/NZS 1427. Vít tự khoan.: Theo AS 3566.1 và AS 3566.2. Vít ren tự động: - Vít chữ thập đầu côn chìm: Theo AS / NZS 4407. - Vít chữ thập đầu tròn chìm: Theo AS / NZS 4406. - Vít chữ thập đầu côn nổi (Hình trái xoan): Theo AS / NZS 4408. - Vít lc giác: Theo AS / NZS 4402. - Vít lc giác, mép g#: Theo AS / NZS 4410. - Vòng đệm lc giác: Theo AS / NZS 4409. - Vít d5p chìm : Theo AS /NZS 4404. - Vít d5p đầu tròn: Theo AS / NZS 4403. GENERRAL GOLDEN ISLAND Project © VHT Engineering 49 Aug-11 - Slotted raised countersunk (oval – common head style): to AS/NZS 4405. Blind rivets Description: Expanding end type with snap mandril. Type: Closed end for external application, open end for internal application. End material: - Aluminium base alloy for metallic coated or colourbond coated steel. - Stainless steel for stainless steel sheet. - Copper for copper sheet. Size: - For sheet metal to sheet metal: 3 mm. - For sheet metal to supports, brackets and rolled steel angles: 4.8 mm. Performance Loads: Provide fasteners capable of transmitting the loads imposed, and sufficient to ensure the rigidity of the assembly. 3 EXECUTION 3.1 ADHESIVES Preparation Substrates: Ensure substrates are: - Clean and free of any deposit or finish which may impair adhesion. - If framed or discontinuous, support members are in full lengths without splicing. - If solid or continuous, excessive projections are removed. - If previously painted, cracked or flaking paint is removed and the surface lightly sanded. Contact adhesive Precautions: Do not use if: - A substrate is polystyrene foam. - A PVC substrate may allow plasticiser migration. - The adhesive solvent can discolour the finished surface. - Dispersal of the adhesive solvent is impaired. Two way method: Immediately after application press firmly to transfer adhesive and then pull both surfaces apart. Allow to tack off and then reposition and press firmly together. Tap areas in contact with a hammer and padded block. - Vít d5p đầu côn nổi: Theo AS /NZS 4405. Rivê Mô tả: loại đầu n, lõi rút. Kiểu: Đầu kín khi $ng dng ngoài nhà, đầu h, cho $ng dng bên trong nhà. Vật liệu: - Thép phủ hợp kim nhôm hay hơp kim màu. - Inox cho tôn inox . - Đồng cho tấm đồng. Kích thước.: - Tôn với tôn: 3 mm. - Giá đ4 tôn, thép góc cán nguội: 4.8 mm. Thực hiện Tải tr*ng: Cung cấp ốc vít có khả năng truyền tải tr*ng l%p đặt, và đủ để đảm bảo độ c$ng của hệ thống. 3 THỰC HIỆN 3.1 KEO Chu3n bị Nền: Bảo đảm nền phải: - Sạch s) và không có bi hay phủ lớp có thề ảnh hư,ng đến keo. - Nếu vật dán có g# hay không liên tc, dán suốt chiều dài, không đ$t nối. - Nếu vật c$ng và liên tc, phải loại b- keo th"a. - Nếu trước được sơn, sơn b! lột phải được loại b- và chà nh5 bằng giấp nhám. Tiếp xúc keo Đề phòng: Không thực hiện nếu : - Chất nền là loam loại polystyren. - Chất nền PVC có thể cho phép di chuyển d3o hơn. - Dung môi keo có thể đổi màu bề mặt hoàn thiện sau cùng. - Bay hơi của dung môi b! hạn chế. Phương pháp hai công đoạn: Ngay lập t$c sau khi trét keo, tách r#i hai bề mặt. Cho phép ướm thử và rồi đ!nh v! lại và nhấn (nén) ch%c ch%n cùng nhau. Vỗ nh5 những vùng tiếp xúc với một cái búa và vật đệm. GENERRAL GOLDEN ISLAND Project © VHT Engineering 50 Aug-11 One way method: Immediately after application bring substrates together and maintain maximum surface contact for 24 hours by clamps, nails or screws as appropriate. If highly stressed employ permanent mechanical fasteners. High strength adhesive tape Preparation: - Non-porous surfaces: Clean with surface cleaning solvents such as isopropyl alcohol / water, wash down and allow to dry. - Porous surfaces: Prime the surface with a contact adhesive compatible with the tape adhesive system. Follow the recommendations of the manufacturer for application to the following: Copper, brass, plasticized vinyl and hydrophilic surfaces such as glass and ceramics in a high humidity environment. Applied lamination pressure: Ensure the tape experiences 100 kPa. Application temperature: Generally above 10°C, cons ult the manufacturer. Completion: Do not apply loads to the assembly for 72 hours at 21°C. 3.2 SEALANT JOINTING Preparation for jointing Cleaning: Cut flush joint surface protrusions and make good. Mechanically clean joint surfaces free of any deposit or finish which may impair adhesion of the sealant. Immediately before jointing remove loose particles from the joint, using oil-free compressed air. Bond breaking: Install bond breaking backing material. Taping: Protect the surface on each side of the joint using 50 mm wide masking tape or equivalent means. On completion of pointing remove the tape and remove any stains or marks from the surface. Primer: Apply the recommended primer to the surfaces in contact with sealant materials. Sealant joint proportions General weatherproofing joints (width:depth): - 1:1 for joint widths < 12 mm. - 2:1 for joint widths > 12 mm. Sealant application General: Apply the sealant to dry joint surfaces using a pneumatic applicator gun. Ensure the sealant completely fills the joint to the required depth; that it is in good contact with the full depth of the sides and that there is no air trapped in the joint. Do not apply the sealant outside the recommended working time for the material or the primer. Weather conditions Two pack polyurethanes: Do not apply the sealant if ambient conditions are outside the Phương pháp một công đoạn: Ngay lập t$c sau trét keo, gữi hai bề mặt với nhau trong 24 gi# b,i ghim, đinh hay vít thích hợp. Nếu lực ép lớn, sử dng khóa cơ khí cố đ!nh. B#ng keo cư&ng $( kết dính cao Chu&n b!: - Bề mặt không xốp: Lau chùi với dung môi làm sạch bề mặt như rượu / Nước isopropylic, rửa và cho phép sấy. - Bề mặt xốp: Đầu tiên phủ bề mặt với một loại keo tiếp xúc thích hợp với Băng keo. Tuân thủ những khuyến cáo của nhà sản xuất cho các $ng dng sau đây: Bề mặt Đồng, đồng thau, nhựa và những bề mặt ưa nước như thủy tinh và những đồ gốm trong một môi trư#ng &m ướt cao. Lực kéo ép băng keo: Bảo đảm 100 kPa. Nhiệt độ cho phép: Thông thư#ng trên 10 °C, tham kh ảo ý kiến các nhà sản xuất. Hoàn thành: Không mang tải trong vòng 72 gi# sau khi thi công , 21 °C. 3.2 TRÉT KÍN M)I N)I Chu3n bị m"i n"i Làm sạch: C%t ph/ng và làm sạch những chỗ lồi lõm trên bề mặt mối nối. Làm sạch ba rớ hoặc lớp phủ mà có thể làm giảm độ bám dính của keo này bằng thiết b! cơ khí. Ngay trước khi nối loại b- bi bằng khí nén. Hàn g%n vết n$t: Thiết đặt vật liệu gia cư#ng cho vết n$t. Quấn băng bảo vệ: Bảo vệ bề mặt về 2 phía của mối nối 50 mm bằng băng che hay tương đương. Khi hoàn thành, loại b- băng và bất k2 vết b&n hay đánh dấu trên bề mặt. Lớp lót: Sử dng lớp lót theo khuyến cáo trên bề mặt tiếp xúc keo. T6 lệ m"i n"i Tổng quát mối nối chống nước (chiều rộng: chiều sâu): - 1:1 Cho những chiều rộng mối nối < 12 MM.. - 2:1 Cho những chiều rộng mối nối > 12 MM. 7ng d,ng Tổng quan: Phun keo b!t kín vào bề mặt khô của mối nối bằng súng hơi. Bảo đảm keo b!t kín hoàn toàn phun tới trong cùng mối nối điều này khiến tiếp xúc tốt trong toàn bộ chiều sâu và không có không khí trong mối nối. Không sử dng keo b!t kín hết hạn sử dng. Đi'u kiện th&i tiết. Keo polyurethanes hai thành phần: không áp dng keo b!t kín nếu những điều kiện xung quanh không th-a điều kiệtn sau: - Nhiệt độ: <5 °C ho ặc> 40 °C GENERRAL GOLDEN ISLAND Project © VHT Engineering 51 Aug-11 following: - Temperature: < 5°C or > 40°C. - Humidity: To the manufacturer’s recommendations. Joint finish General: Force the sealant into the joint and finish with a smooth, slightly concave surface using a tool designed for the purpose. Protection General: Protect the joint from inclement weather during the setting or curing period of the material. - Độ ảm: Theo khuyến cáo của Nhà sản xuất. Hoàn thiện Tổng thể: Ép keo vào mối nối và hoàn thiện với một bề mặt nh1n hơi lõm, bằng cách sử dng công c chuyên dng. Bảo vệ Tổng quan: Bảo vệ mối nối kh-i th#i tiết kh%c nghiệt trong th#i gian thi công hay th#i k2 xử lý vật liệu. GENERRAL GOLDEN ISLAND Project © VHT Engineering 52 Aug-11 0182 FIRE-STOPPING 1 GENERAL 1.1 CROSS REFERENCES General General: Conform to the General requirements worksection. 1.2 GENERAL STANDARDS General Service penetration fire-stopping systems: To BCA clause C3.15. Control joint fire-stopping systems: To AS 4072.1. 1.3 INSPECTION Notice Inspection: Give sufficient notice so that inspection may be made of the following: - Service penetrations completed and ready for fire-stopping. - Finished fire-stopping, before being concealed. 1.4 TESTS Service penetration fire-stopping systems Insulation measurements: Required. Multiple penetration fire-stopping systems Insulation measurements: Required. 1.5 SAMPLES Sample panels General: Supply a sample panel of each fire-stopping assembly, on representative substrates. If built into the works, mark them. Size: 500 mm run for junction seals and 500 x 500 mm area for penetration seals. 1.6 SUBMISSIONS 0182 CH)NG CHÁY LAN 1 TỔNG QUAN 1.1 THAM CHIẾU CHÉO Tổng thể Tổng quan: Tuân thủ theo chương yêu cầu chung . 1.2 TIÊU CHU2N CHUNG Tổng thể Chống cháy lan lỗ m, xuyên kết cấu: theo BCA điều C3.15 Chống cháy lan mối nối Theo AS 4072.1. 1.3 KIỂM TRA Chú ý Kiểm tra: Cho thông báo đầy đủ để có thể kiểm tra trong các trư#ng hợp sau: - Hoàn tất lỗ m, xuyên kết cấu, chu&n b! chống cháy lan. - Hoàn tất chống cháy lan, chu&n b! hoàn thiện. 1.4 TH8 NGHIỆM Ch"ng cháy lan lỗ m9 xuyên kết cấu Đo độ cách ly: phải thực hiện. Ch"ng cháy lan nhi'u lỗ m9 xuyên kết cấu Đo độ cách ly: phải thực hiện. 1.5 TRÌNH M:U Bảng mẫu Tổng quan: Cung cấp bảng m+u mỗi loại chống cháy lan, trên nền đặc trưng. Đánh dấu nếu sử dng vào trong công trình. Kích thước: 500 mm dài cho các mối nối và 500 x 500 mm lổ m,. GENERRAL GOLDEN ISLAND Project © VHT Engineering 53 Aug-11 Manufacturers’ information Type tests: Submit type test certificates for each combination of fire-stopping system, application, type of service, substrate and penetration orientation. Include drawings of tested details. Physical performance: Submit report to AS 4072.1 Appendix C. Product data: Submit evidence that systems specified without reference to brand conform to specified requirements. Instructions: Submit copies of relevant manufacturers’ instructions, for systems specified without reference to brand. Material safety data sheets (MSDS): Submit MSDS for systems specified without reference to brand. Notice General: Give notice if substrates or penetrants or both are not suitable for fire-stopping. 1 PRODUCTS 1.1 MATERIALS General Shelf life: Ensure materials used have not exceeded their shelf life. Toxic materials: Free of asbestos and lead and free of, nor requiring the use of, toxic solvents. Toxicity in fire: Non-toxic. Fire-stop mortars Type: Re-enterable cement-based compound, mixed with water. Non-shrinking, moisture resistant. Insoluble in water after setting. Formulated compound of incombustible fibres Material: Formulated compound mixed with mineral fibres, non-shrinking, moisture resistant. Insoluble in water after setting. Fibre stuffing Material: Mineral fibre stuffing insulation, dry and free of other contaminants. Standard: AS/NZS 4859.1 Section 8. Fire-stop sealants Material: Elastomeric sealant. Soft, permanently flexible, non-sag, non-shrinking, moisture resistant. Capable of providing a smoke-tight, gas-tight and waterproof seal when properly installed. Insoluble in water after setting. Fire-stop foams Material: Single component compound of reactive foam ingredients, non-shrinking, 1.6 ĐỆ TRÌNH Thông tin nhà sản xuất. Thử nghiệm type test: Nộp giấy ch$ng nhận kiểm tra đối với t"ng chất chống cháy lan, $ng dng, loại bề mặt, hình dạng lỗ m,. . Bao gồm các bản v) chi tiết thử nghiệm. Thực hiện: Cung cấp báo cáo Theo AS 4072.1 Ph lc. C. Dữ liệu Sản ph&m: Cung cấp bằng ch$ng vật tư đệ trình, mà không theo danh sách vật liệu đề ngh! sử dng, phù hợp với những yêu cầu đã xác đ!nh trong hồ sơ này. Ch' d+n: Cung cấp bảng photo ch' d+n của nhà sản xuất các vật tư không theo danh sách vật liệu đề ngh! sử dng. Bảng thông số vật tư(MSDS): Cung cấp bảng MSDS các vật tư đệ trình, mà không theo danh sách vật liệu đề ngh! sử dng. Chú ý Tổng quan: Phải thông báo trước nếu bề mặt hay lỗ m, hay cả hai không thích hợp cho công tác thi công chất ngăn cháy.. 2 SẢN PH2M 2.1 VT LIỆU Tổng thể Th#i gian bảo quản: Bảo đảm vật liệu được dùng không quá hạn sử dng. Độc tính: Vật liêu sử dng không có a-mi-ăng, axít và không có, mà c6ng không yêu cầu sử dng, dung môi độc. Độc tính khi cháy: Không độc. V;a ch"ng cháy lan Loại hỗn hợp gốc xi măng, trộn đều với nước. Không co, chống &m. Không tan trong nước sau khi thi công. Hỗn h*p s*i khoáng không cháy $ư*c. Vật liệu: Hỗn hợp được trộn l+n với những sợi khoáng, không co, ch!u &m. Không tan trong nước sau khi thi công. Fibre no Vật liệu: Sợi Khoáng no, cách nhiêt, khô và không có những chất gây ô nhi(m khác. Tiêu chu&n: AS / NZS 4859,1 Phần 8. Chất ng#n cháy lan (fire stop) Vật liệu: keo đàn hồi. Mềm, thư#ng linh hoạt, không chùng, không co h5p lại, chống GENERRAL GOLDEN ISLAND Project © VHT Engineering 54 Aug-11 moisture resistant. Insoluble in water after setting. Fire-stop putty Material: Single component, mouldable, permanently flexible, non-shrinking, moisture resistant, intumescent compound which expands on exposure to surface heat gain, forming a high-volume thermally insulating char that closes gaps and voids, resists the turbulence of a severe fire. Capable of being placed by hand to form an immediate fire seal. Insoluble in water after setting. 1.2 COMPONENTS Fire-stop collars Material: Mechanical device with incombustible intumescent fillers covered with sheet steel jacket. Airtight and watertight. Fire-stop pillows Material: Formed self-contained compressible flexible mineral fibre in cloth bags, rated to permit frequent changes in service. 2 EXECUTION 2.1 EXECUTION GENERALLY General Extent: Fire-stop and smoke-stop interruptions to fire-rated assemblies, materials and components, including penetrations through fire-rated elements, breaks within fire-rated elements (e.g. expansion joints), and junctions between fire-rated elements. The Fire- stopping systems schedule is not necessarily comprehensive. Sequence: Fire-stop after services have been installed through penetrations and properly spaced and supported, after sleeving where appropriate, and after removal of temporary lines, but before restricting access to the penetrations, including before dry lining. Ventilation: Supply ventilation for non-aqueous solvent-cured materials. Density: Apply fire-stopping material to uniform density. Fire-stopping exposed to view: Finish surfaces to a uniform and level condition. Cable separation: Maintain. Protection: Protect adjacent surfaces from damage arising through installation of fire- stopping. Protect completed fire-stopping from damage arising from other work. Loose or damaged fire-stopping material: Remove and replace. Penetrations by pipes and ducts: Allow for thermal movement of the pipes and ducts. Preventing displacement: Reinforce or support fire-stopping materials with non- combustible materials when: &m. Có khả năng kín khói, kín gas và không thấm nước khi thi công đúng. Không hòa tan trong nước sau khi thi công. Fire-stop b/t Vật liệu: hỗn hợp các đơn chất b*t phản $ng, không co, chống &m,.Không tan trong nước sau khi sự thi công. Mát tít d<ng lửa Chất liệu: đơn chất, có thể nặn, vĩnh vi(n linh hoạt, không co ngót, chống &m, hợp chất truơng n, trên bề mặt nóng, tạo thành một thể tích lớn chất cách nhiệt lấp những khoảng trống và khe h,, ngăn ng"a cháy lan. Có khả năng được đặt bằng tay để tạo thành chất ngăn cháy lan ngay lập t$c. Không hòa tan trong nước sau khi thi công. 2.2 THÀNH PHẦN Vòng ng#n lửa Vật liệu: thiết b! Cơ khí với những ngư#i làm đầy sưng không cháy được được bao trùm với thép tấm jacket. Kín và kín nước.. G"i ng#n lửa. Chất liệu: Sợi khoáng nén trong túi vải, kích thước qui chu&n để d( sử dng. 3 THỰC HIỆN 3.1 TỔNG THỂ Tổng quan Phạm vi: Xuyên các chất ngăn cháy lan, ngăn khói, bao gồm lỗ m, xuyên kết cấu chống cháy, khe co giãn trong kết cấu chống cháy và mối nối giữa 2 kết cấu chống cháy. Bảng thông số chất ngăn cháy lan không phải là toàn diện. Thông thư#ng: Fire stop đã l%p đặt trong lỗ m, và không gian cần thiết, sau khi l%p đặt ống lót (sleeve), sau khi tháo tuyến cáp tạm th#i, nhưng trước khi hoàn tất đóng lổ m, bao gồm cả kéo cáp. Thông gió: Cung cấp Thông gió cho dung môi không có nước.. Mật độ: phải đồng nhất. Chất ngăn cháy h, thấy được: Hoàn thiện bề mặt cùng chất liệu và ph/ng mặt với bề mặt xung quanh. Tách các tuyến cáp điện: Phải tuân thủ Bảo vệ: Bảo vệ những bề mặt kề bên không hư h-ng do thi công fire stop. Bảo vệ fire stop tránh hư h-ng do thi công công việc khác. Fire stop b! hư h-ng: Loại b- và thi công lại. GENERRAL GOLDEN ISLAND Project © VHT Engineering 55 Aug-11 - The unsupported span of the fire-stopping materials > 100 mm. - The fire-stopping materials are non-rigid (unless shown to be satisfactory by test). Large openings: Provide fire-stopping capable of supporting the same loads as the surrounding element or provide similar structural support around the opening. Preparation Cleaning: Clean substrates of dirt, dust, grease, oil, loose material, and other matter which may affect bond of fire-stop material. Primer: Clean and dry substrates for primers and sealants. Restraint: Install backing and/or damming materials to arrest liquid material leakage. Remove temporary dams after material has cured. 2.2 SYSTEMS Fire-stop mortars Ambient conditions: Do not install below 5°C. Fibre stuffing Installation: Compress to 40% of its uncompressed volume. Fire-stop sealants Ambient conditions: Do not store above 32°C. Do not install outside the temperature range recommended by the sealant manufacturer. Do not install when humidity exceeds that recommended by the sealant manufacturer for safe installation. Fire-stop foams Ambient conditions: Do not store above 32°C. Do not install below 15°C or above 32°C. Do not apply when temperature of substrate and air is below 15°C. Maintain this minimum temperature before, during and for 3 days after installation. Installation: Test substrates for adhesion and prime if necessary. Place in layers to ensure homogenous density, filling cavities and spaces. Place sealant to completely seal junctions with adjacent dissimilar materials. Fire-stop pillows Ambient conditions: Do not install in conditions outside of the manufacturer’s recommendations. Labelling Label each fire-stopping installation with a permanently fixed tag or sticker containing the following information: - Manufacturer’s name. - Name and address of installer. - Date of installation. Lỗ m, cho ống/ ống gió xuyên qua: Cho phép luân chuyển nhiệt của ống / ống gió. Ngăn ng"a d!ch chuyển: Gia cố hay treo đ4 fire stop với nguyên liệu không d( cháy, khi.: - Khoảng cách không treo đ4 fire stop > 100 mm. - Fire stop loại không mềm (tr" khi ch$ng minh đã đạt bằng thử nghiệm). Lỗ m, lớn: Cung cấp fire stop có khả năng treo đ4 tải tr*ng xung quanh hay cung cấp cấu trúc treo đ4 tương tự xung quanh lỗ m,. Ch3n bị Làm sạch: Làm sạch các chất bi, b&n, dầu m4, dầu, ba rớ và các chất khác có thể ảnh hư,ng đến liên kết của fire stop. Lớp lót: Làm sạch và khô bề mặt trước khi thi công lớp lót và trám trét. Che ch%n: l%p đặt vật liệu che kín k) h, chống rò chảy chất l-ng. Loại b- vật liệu che tạm th#i sau thi công xong. 3.2 HỆ TH)NG V;a ch"ng cháy lan. Điều kiện xung quanh: Không l%p đặt , dưới 5°C. S*i khoáng no L%p đặt: Nén đến 40% so với thể tích lúc chưa nén. Keo ch"ng cháy lan Điều kiện môi trư#ng xung quanh: bảo quản dưới 32oC, không đặt bên ngoài phạm vi nhiệt độ khuyến cáo của nhà sản xuất keo. Không l%p đặt khi độ &m vượt quá khuyến cáo của nhà sản xuất. B/t ch"ng cháy lan. Điều kiện môi trư#ng xung quanh: Không bảo quản trên 32 độC. Không l%p đặt khi nhiệt độ dưới 15° C hoặc trên 32 độ C. Không l%p đặt khi nhiệt độ bề mặt và không khí dưới 15 độ C. Duy trì nhiệt độ này tối thiểu trước, trong và trong 3 ngày sau khi l%p đặt. L%p đặt: Kiểm tra bề mặt trét keo và lớp lót nếu cần thiết. Thi công t"ng lớp để đảm bảo mật độ đồng nhất, đổ đầy các hốc và k) h,. Đổ keo hoàn toàn trét kín nối liền với các vật liệu lân cận khác. G"i ch"ng cháy lan. Điều kiện môi trư#ng xung quanh: Không l%p đặt trong các điều kiện bên ngoài các khuyến ngh! của nhà sản xuất. GENERRAL GOLDEN ISLAND Project © VHT Engineering 56 Aug-11 2.3 COMPLETION SUBMISSIONS Certification General: Submit evidence of compliance, in accordance with the recommendations of AS 4072.1 Appendix B. Certification: Submit a completed certification document for installed fire-stopped penetrations and control joints. - Form: To Figure B1 of AS 4072.1. Schedule: Submit a schedule of installed fire-stopped penetrations and control joints. - Form: To Figure B2 of AS 4072.1. User manual For fire-stopping systems which are intended to be modified in service, submit user manual. 2.4 MAINTENANCE Cleaning Remove spilled and excess fire-stopping materials without damaging other work. Ghi nhãn G%n nhãn mỗi loại fire stop với một nhãn vĩnh cữu ch$a đựng thông tin sau đây.: - Tên của Nhà sản xuất.. - Tên và Đ!a ch' của Ngư#i l%p đặt.. - Ngày tháng l%p đặt. 3.3 ĐỆ TRÌNH HOÀN THÀNH Chứng nhận Tổng quan: Gửi bằng ch$ng về sự phù hợp, theo các khuyến ngh! của AS 4072,1 Ph lc B. Ch$ng nhận: Gửi một văn bản ch$ng nhận hoàn thành l%p đặt fire stop các lỗ m, và mối nối. - M+u : Theo bảng B1 của AS 4072.1. Kế hoạch: Trình kế hoạch l%p đặt fire stop các lỗ m, và mối nối. - M+u: Theo bảng B2 của AS 4072.1. Hư+ng dẫn sử d,ng Đối với các hệ thống ngăn chặn lửa được dự đ!nh có thay đổi trong quá trình hoạt động, trình hướng d+n sử dng. 3.4 BẢO DƯ=NG Làm sạch Loại b- chất chống cháy lan dư th"a mà không làm h-ng công việc khác. GENERRAL GOLDEN ISLAND Project © VHT Engineering 57 Aug-11 0183 METALS AND PREFINISHES 1 GENERAL 1.1 CROSS REFERENCES General General: Conform to the General requirements worksection. 2 PRODUCTS 2.1 METALS Aluminium and aluminium alloys Drawn pipe: To AS/NZS 1867. Drawn rod, bar and strip: To AS/NZS 1865. Extrusions: To AS/NZS 1866. Plate and sheets: To AS/NZS 1734. Coated steel Electrogalvanizing ferrous hollow and open sections: To AS 4750. Metallic-coated steel: - Ferrous open sections zinc coated by an in-line process: To AS/NZS 4791. - Ferrous hollow sections zinc coated by a continuous or specialised process: To AS/NZS 4792. Metallic-coated steel sheet: To AS 1397. Metal thicknesses specified are base metal thicknesses. Steel wire: To AS/NZS 4534. Copper and copper alloys Casting: To AS 1565. Plate, sheet and strip: To AS 1566. Rods, bars and sections: To AS/NZS 1567. Stainless steel 0183 KIM LO>I VÀ X8 LÝ BỀ M?T 1 TỔNG QUAN 1.1 NH1NG THAM CHIẾU CHÉO Tổng quan Tổng quan: Tuân thủ các chương yêu cầu chung. 2 SẢN PH2M 2.1 KIM LO>I Nhôm và nh;ng h*p kim nhôm .ng kéo nóng Theo AS / NZS 1867. Cột, thanh và dải kéo nóng : Theo AS / NZS 1865. Kim loại đ&y nóng: Theo AS / NZS 1866.. Tôn và thép tấm: Để AS / NZS 1734.. Thép xử lý b' m@t Mạ điện cho s%t dạng ống và thép hình Theo AS 4750.. Thép b*c kim loại: - Mạ k)m cho s%t hình: theo AS / NZS 4791. - Mạ điện cho s%t dạng ống: theo AS / NZS 4792. Tôn b*c kim loại: theo AS 1397. Quy đ!nh độ dày b*c kim loại theo độ dày tôn. Cáp thép: theo AS / NZS 4534. ĐAng và nh;ng h*p kim $Ang $B. Đúc: Theo AS 1565.. Tấm, dải và lá: theo AS 1566. Thanh, C*c và mặt c%t: Theo AS / NZS 1567. Thép không gC Thanh: Theo ASTM A276.. GENERRAL GOLDEN ISLAND Project © VHT Engineering 58 Aug-11 Bars: To ASTM A276. Plate, sheet and strip: To ASTM A240/A240M. Welded pipe (round): To AS 1769. Welded pipe (square): To ASTM A554. Steel Sheet: To AS/NZS 1595. Structural bars and sections: To AS/NZS 3679.1. Structural hollow section: To AS 1163. Steel for prefinishes Cold rolled bar: To AS 1443 ‘bright’. Cold rolled sheet: To AS/NZS 1595. - Designation: CA2S-E. Electric resistance welded pipe: To AS 1450. 3 EXECUTION 3.1 GENERAL Metal separation Incompatible sheet metals: Provide separation by one of the following: - Apply an anti-corrosion low moisture transmission coating such as alkyd zinc phosphate primer or aluminium pigmented bituminous paint to contact surfaces. - Insert a concealed separation layer such as polyethylene film, adhesive tape, or bituminous felt. Incompatible fixings: Do not use. Incompatible service pipes: Install lagging or grommets. Do not use absorbent, fibrous of paper products. Brazing General: Ensure brazed joints have sufficient lap to provide a mechanically sound joint. Butt joints: Do not use butt jointing for joints subject to load. If butt joints are used, do not rely on the filler metal fillet only. Filler metal: To AS/NZS 1167.1. Finishing Visible joints: Finish visible joints made by welding, brazing or soldering using methods appropriate to the class of work (including grinding or buffing) before further treatment such as painting, galvanizing or electroplating. Ensure self-finished metals are without Tấm, tôn và lá: theo ASTM A240/A240M. .ng Hàn: theo AS 1769. .ng vuông Hàn: theo ASTM A554. Thép Tôn: Theo AS / NZS 1595.. Thép dạng thanh: theo AS / NZS 3679,1. Thép ống: theo AS 1163. Thép $ể xử lý b' m@t Dạng thanh, cán nguội: theo AS 1443 “Bright”. Tôn cán nguội: theo AS / NZS 1595. - Ch' đ!nh: CA2S- E.. .ng hàn điện: theo AS 1450. 3 THỰC HIỆN 3.1 TỔNG QUAN Phân cách kim loại Các kim loại không tương thích: tách ra b,i một trong số biện pháp sau đây: - Phủ lớp kim loại trung gian độ &m thấp, chống ăn mòn như lớp lót Phốt phát K)m ALKYD hay sơn bitum nhôm vào những mặt tiếp xúc. - Chèn một lớp phân tách , giữa như Phim Polyethylen, băng dính Hay giấy dầu. Các g%n kết không tương thích: không được sử dng. Các ống không tương thích: Sử dng chất cách nhiệt, dây th"ng. Không sử dng giấy thấm nước, có xơ. Hàn thau Tổng quan: Bảo đảm những mối hàn đuợc tạo rãnh đủ để tạo mối hàn đủ sâu. Mối nối cung đầu: không sử dng mối nối này cho vật mang tải. Nếu được sử dng, phải có gia cố khác. Kim loại hàn: Theo AS / NZS 1167.1.. Hoàn thiện b' m@t Mối nối thấy được: hoàn thiện những mối nối bằng cách hàn, hàn thau hay hàn sử dng những phương pháp thích hợp đối với lớp công việc (bao gồm mài hay đánh bóng) trước khi sơn, tráng k)m hay mạ điện. Bảo đảm không có khác biệt màu s%c trên bề mặt sau khi hoàn tất mối nối. Chu3n bị GENERRAL GOLDEN ISLAND Project © VHT Engineering 59 Aug-11 surface colour variations after jointing. Preparation General: Before applying decorative or protective prefinishes to metal components, complete welding, cutting, drilling and other fabrication, and prepare the surface using a suitable method. Standard: To AS 1627. Priming steel surfaces: If site painting is specified to otherwise uncoated mild steel or similar surfaces: - Prime after fabrication and before delivery to the works. - After installation, repair damaged priming and complete the coverage to unprimed surfaces. Welding Aluminium: To AS 1665. Stainless steel: To AS/NZS 1554.6. Steel: To AS/NZS 1554.1. 3.2 SELF FINISHING Mechanical finishes Bright finished copper alloy surfaces: For indoor applications, apply a clear lacquer protecting coating. 3.3 ELECTROPLATING Electroplated coatings Chromium on metals: To AS 1192. Nickel on metals: To AS 1192. Service condition number: At least 2. Zinc on iron or steel: To AS 1789. 3.4 ANODISING Anodising Standard: To AS 1231. Thickness grade: - Indoor applications: At least AA 10. - Outdoor applications: AA 15 to AA 20. 3.5 METAL SPRAYING Metal spray Tổng quan: Trước khi xử lý bề mặt cho kim loại, công tác hàn, c%t, khoan và các gia công khác c6ng như chu&n b! bề mặt phải sử dng phương pháp thích hợp. Tiêu chu&n: Theo AS 1627.. Lớp lót bề mặt thép: Nếu sơn được ch' đ!nh thực hiện tại công trư#ng thay cho các biện pháp xử lý khác cho thép đen hoặc các bề mặt tương tự: - Sơn lớp lót sau khi gia công và trước khi giao hàng tới công trư#ng. - Sau khi l%p đặt, sửa chữa hư h-ng của lớp lót và hoàn thành lớp hoàn thiện bề mặt. Hàn Nhôm: Theo AS 1665.. Thép không r': Theo AS / NZS 1554,6. Thép: Theo AS / NZS 1554.1. 3.2 HOÀN THIỆN TỰ NHIÊN Hoàn thiện Cơ khí Hoàn thiện bề mặt hợp kim đồng sáng cho những $ng dng trong nhà, sử dng một lớp sơn trong suốt để bảo vệ. 3.3 M> ĐIỆN Mạ $iện Crôm trên kim loại: Theo AS 1192.. Ni ken trên kim loại: Theo AS 1192.. Số lần mạ: ít nhất 2. K)m trên s%t hay thép: Theo AS 1789.. 3.4 M> ANODE Mạ anode Tiêu chu&n: Theo AS 1231. Độ dày lớp mạ: - 8ng dng trong nhà: ít nhất AA 10. - 8ng dng ngoài tr#i: AA 15 đến AA 20. 3.5 PHUN KIM LO>I Phun kim loại Tiêu chu&n: Theo ISO 2063.. Độ dày tối thiểu: - 8ng dng trong nhà: 125 µm. GENERRAL GOLDEN ISLAND Project © VHT Engineering 60 Aug-11 Standard: To ISO 2063. Minimum thicknesses: - Indoor applications: 125 µm. - Outdoor applications: 175 µm. Process: Electric arc. Seal coat: Cover the metal spray finish with two coats of vinyl seal to a total dry film thickness of 80 µm. 3.6 POWDER COATING Standards Application to aluminium and aluminium alloy substrates: AS 3715. Application to substrates other than aluminium: AS 4506. Preparation General: Use chemical pretreatments. If recommended, provide conversion coatings. Aluminium: Pretreat to AS 3715 Appendix G. Galvanized and metallic-coated steel: Clean by immersing in a suitable alkaline or acidic solution, apply a zinc phosphate chemical conversion coating, rinse and degas. Unprotected steel: Remove rust to the recommendations of AS 1627.4 to grade Sa 2½ of AS 1627.9. Clean by immersing in trichloroethylene or an alkaline solution, and apply a coat of iron phosphate. Thermoset powder coating generally Pre-clean: If surface contamination has occurred or is suspected, clean surface with a proprietary pre-cleaning solvent/detergent prior to powder application. Thermoset fluopolymer coating: Provide chemical conversion of the surface to amorphous chromium phosphate to ASTM 1730D Type B, Method 5 (Amorphous chromium phosphate treatment). Delete if fluoropolymer is not applicable. Application: Use an electrostatic spray gun or fluidised bed and ensure no dust particles or other impurities blemish the final product. Baking: After application, bake the film in an oven accurately controlled to the temperature and for the period recommended by the coating system manufacturer. Check for correct paint cure by solvent testing. Adjust pre-heat and line speed to ensure full cure. Damage: Protect the coatings from damage during coating operations, fabrication shipping, storage and installation. Minor damage: Touch up as recommended by coating system manufacturer. Thermoset polyester powder coating Standards: - Aluminium and aluminium alloy substrates: To AS 3715. - 8ng dng ngoài tr#i: 175 µm. Qui trình: hồ quang điện.. Che phủ: Che phủ kim loại đã hoàn tất phun xử lý bằng hai lớp vinyl bề dày tổng 80 µm. 3.6 SDN TENH ĐIỆN Tiêu chu3n Áp dng đối với nhôm và hợp kim nhôm: theo AS 3715. Áp dng đối với các kim loạI khác nhôm: Theo AS 4506. Chu3n bị. Tổng quan: Tiền xử lý bằng hóa chất. Nếu khuyến cáo, cung cấp lớp phủ trung gian. Nhôm: Tiền xử lý theo AS 3715 Ph lc G. Thép mạ k)m và phủ kim loại: Vệ sinh bằng cách nhúng chìm trong dung d!ch kiềm hay axit thích hợp, sử dng lớp phủ trung gian phốt phát k)m, rửa và khử khí. Thép không có lớp bảo vệ: loại b- r' theo khuyến ngh! của AS 1627,4 đến lớp SA2 ½ theo AS 1627,9. Làm sạch bằng cách ngâm trong dung d!ch trichloroethylene hay kiềm, và phủ lớp phosphate s%t. Sơn tĩnh $iện Làm sạch sơ bộ : Nếu bề mặt b&n hay nghi b&n, làm sạch bề mặt bằng dung môi/ thuốc t&y làm sạch trước khi sơn tĩnh điện. Phủ lớp fluopolymer nhiệt r%n: Cung cấp lớp chuyển đổi hóa h*c bằng phosphate crom vô đ!nh hình theo ASTM 1730D Loại B, Phương pháp 5 (xử lý bằng phosphate crom vô đ!nh hình). Xóa nếu không áp dng fluoropolymer. 8ng dng: Sử dng súng phun tĩnh điện hoặc giư#ng sôi và đảm bảo không có các hạt bi hoặc các tạp chất khác trong sản ph&m cuối cùng. Hấp: sau cùng, hấp sơn trong lò có nhiệt độ được kiểm soát chính xác theo th#i gian được khuyến cáo b,i nhà sản xuất. Kiểm tra chất lượng sơn theo phương pháp kiểm tra dung môi. Điều ch'nh tốc độ hấp để bảo đảm chất lượng cho qui trình hấp. Hư hại: Bảo vệ các lớp sơn không hư hại trong quá trình sơn, vận chuyển, lưu trữ và l%p đặt. Hư hại ph: Lưu ý các khuyến cáo của nhà sản xuất khi đng vào lớp sơn. Sơn tĩnh $iện polyester Tiêu chu&n: - Nhôm và hợp kim nhôm: theo AS 3715. - Những Kim loại khác với Nhôm: Theo AS. 4506. Phủ nhiệt fluoropolymer. Mô tả: Phun lớp phủ lên những sản ph&m nhôm được thực hiện tại nhà máy, bao gồm GENERRAL GOLDEN ISLAND Project © VHT Engineering 61 Aug-11 - Metal substrates other than aluminium: To AS 4506. Thermoset fluoropolymer coating Description: Factory applied spray coatings on aluminium products, including PVF2 and PFTE coatings. Standard: To AS 3715. Quality control: Submit an ongoing application and performance quality control report. Include production methods and tests to the Quality control table using actual substrates for this project: 3.7 PREPAINTING Air-drying enamel Application: Spray or brush. Finish: Full gloss. General use: - Primer: Two-pack epoxy primer to AS/NZS 3750.13. - Top coats: 2 coats to AS 3730.6. Oil resistant use: - Primer: Two-pack epoxy primer to AS/NZS 3750.13. - Top coats: 2 coats to AS 4025.1. Equipment paint system Description: Brush or spray application using paint as follows: - Full gloss enamel finish coats, oil and petrol resistant: AS 4025.1, two coats. - Prime coat to metal surfaces generally: AS 4089 or AS 4025.4. - Prime coat to zinc-coated steel: AS 3730.15. - Undercoat: AS 4025.2. Prepainted metal products Product type as noted in AS/NZS 2728: Not lower than the type appropriate to the field of application. Two-pack liquid coating Application: Spray. Finish: Full gloss. Primer: Two pack epoxy primer to AS/NZS 3750.13. Topcoat: - Internal use: Proprietary polyurethane or epoxy acrylic system. - External use: Proprietary polyurethane system. lớp phủ PVF2 và PFTE. Tiêu chu&n: Theo AS 3715.. Kiểm soát chất lượng: Đệ trình báo cáo $ng dng đang thực hiện và kiểm soát chất lượng hoạt động. Bao gồm các phương pháp sản xuất và thử nghiệm thể hiện trong bảng kiểm soát chất lượng áp dng cho các bề mặt trong dự án này 3.7 SDN HOÀN CHFNH TRƯGC Men Công nghệ: Phun hoặc quét. Hoàn thiện: bóng hoàn toàn. Tổng quát: - Lớp lót: epoxy 2 thành phần theo AS /NZS 3750.13. - Lớp hoàn thiện: 2 lớp Theo AS 3730.6.. Áp dng trong trư#ng hợp chống dầu m4: - Lớp lót: epoxy 2 thành phần theo AS /NZS 3750.13. - Lớp hoàn thiện: 2 lớp Theo AS. 4025.1. Hệ th"ng sơn Mô tả: quét hoặc phun sơn bằng loại sơn như sau: - Lớp hoàn ch'nh bằng men bóng chống dầu m4 02 lớp theo AS 4025.1. - Lớp sơn lót đầu tiên lên bề mặt kim loại nói chung theo AS 4089 hay AS 4025.4. - Lớp sơn lót đầu tiên lên bề mặt thép mạ k)m theo AS 3730.15. - Lớp lót th$ nhì: AS 4025,2. Sản ph3m kim loại $ư*c sơn hoàn chCnh trư+c. Loại sản ph&m được nêu trong AS / NZS 2728: Không cho phép thấp hơn kiểu phù hợp với phạm vi áp dng. L+p phủ 02 thành phần Công nghệ: phun. Hoàn thiện: có độ bóng cao.. Lớp lót: nhựa epoxy hai thành phần theo AS 3730.15. Lớp phủ bên ngoài: - Trong nhà: Sơn epoxy gốc acrylic hay polyurethane. - Ngoài nhà: Sơn polyurethane. 3.8 HOÀN T!T Hư hBng GENERRAL GOLDEN ISLAND Project © VHT Engineering 62 Aug-11 3.8 COMPLETION Damage General: If prefinishes are damaged, including damage caused by unauthorised site cutting or drilling, remove and replace the damaged item. Repair General: If a repair is required to metallic coated sheet or electrogalvanized on inline galvanized steel products, clean the affected area and apply a two-pack organic primer to AS/NZS 3750.9. Tổng quát: Nếu lớp hoàn thiện ban đầu b! hư h-ng ngay cả do b! c%t, khoan không phép, sửa chữa và sơn lại. Sửa ch;a Tổng quát: Nếu phải sửa chữa lớp phủ kim loại hay lớp mạ k)m, làm sạch vùng b! hư và sử dng lớp lót 02 thành phần hữu cơ theo AS/NZS 3750.9. GENERRAL GOLDEN ISLAND Project © VHT Engineering 63 Aug-11 0186 BUILDING IT COMPONENTS 1 GENERAL 1.1 AIMS Responsibilities General: Provide IT components and systems as follows. Selections: As documented. 1.2 CROSS REFERENCES General General: Conform to the General requirements worksection. 1.3 SUBMISSIONS Technical data General: Submit technical data for all components including the following: - Hardware and software manufacturer’s technical literature. 2 PRODUCTS 2.1 ACTIVE COMPUTER HARDWARE Computer hardware Conform to the Computer hardware schedule. Network hub/switch Type: Managed Gigabit ethernet Layer 2. Mounting: Rack mounting. Network router Type: Gigabit ethernet. Functions: Static IP, dynamic IP, integrated DHCP, PPPoE, and device name support. Mounting: Rack mounting. Wireless access point 0186 HỆ TH)NG IT TRONG CÔNG TRÌNH 1 TỔNG QUÁT 1.1 M4C ĐÍCH Trách nhiệm Tổng quát: Cung cấp hệ thống IT như sau. Lưa ch*n: Theo tài liệu thiết kế. 1.2 THAM CHIẾU Tổng quát Tổng quát: Tuân thủ các chương Yêu cầu chung. 1.3 ĐỆ TRÌNH Thông s" kH thuật Tổng quát: Đệ tr2inh thông số kỹ thuật của các hạng mc như sau: - Tài liệu kỹ thuật phần c$g và phần mềm của nhà sản xuất phát hành. 2 SẢN PH2M 2.1 PHẦN C7NG MÁY TÍNH Phần cứng máy tính Theo bảng kê thông số máy tính. Hub/switch Loại: Mạng Gigabit ethernet Layer 2. L%p: Rack. Router Loại: Gigabit ethernet. Ch$c năng: Static IP, dynamic IP, integrated DHCP, PPPoE và hỗ trợ tên thiết b!. L%p: Rack. Wireless access point GENERRAL GOLDEN ISLAND Project © VHT Engineering 64 Aug-11 Compatibility: IEEE 802.11b and IEEE 802.11g/n. Modes: Wireless access point, point-to-point bridge, point-to-multi-point wireless bridge, wireless client and wireless repeater. ADSL modem Graphical User Interface (GUI): Required to permit modification of settings to connect to Internet Service Provider (ISP). Functions: Static IP, Dynamic IP, PPPoE/PPPoA and Bridge connections. Coaxial cable modem Graphical User Interface (GUI): Required to permit modification of settings to connect to Internet Service Provider (ISP). Functions: Static IP, Dynamic IP, PPPoE/PPPoA and Bridge connections. Backup/archive facilities Type: Tape. Mounting: Rack mounting. Printers General: Conform to the Printers schedule. 2.2 SOFTWARE General General: Provide the software required for the operation and management of the building IT systems and equipment including the following: - All passwords, access codes and other means used to limit or control access to, or modification (including extension) of, the software. - All software and manuals necessary to modify or extend the software. - Back-up copies of software in electronic format. - Installation of all software updates issued before the end of the defects liability period. Compatibility: Provide software systems that are planned to have upgrades backward compatible, so that each upgrade does not require user input or changes to base data or to the site specific installation. Licence: Provide fully licensed versions of all software and licenses for all users defined in the documents. OSI model: Provide software that operates on the open system interconnection (OSI) model. System software Conform to the System software schedule. Application software Provide the software required for the operation and management of building services Phù hợp với IEEE 802.11b and IEEE 802.11g/n. Chế độ (mode): Wireless access point, point-to-point bridge, point-to-multi-point wireless bridge, wireless client và wireless repeater. ADSL modem Graphical User Interface (GUI): Yêu cầu đệ trình thông số cài đặt để nối mạng internet (ISP). Ch$c năng: Static IP, Dynamic IP, PPPoE/PPPoA và Bridge connections. Coaxial cable modem Graphical User Interface (GUI): Yêu cầu đệ trình thông số cài đặt để nối mạng internet (ISP). Ch$c năng: Static IP, Dynamic IP, PPPoE/PPPoA và Bridge connections. Tiện ích Backup/archive Loại: Tape. L%p: Rack. Máy in Tổng quát: Theo bảng thông số máy in. 2.2 PHẦN MỀM Tổng quát Tổng quát: Cung cấp phần mềm để vận hành hệ thống IT trong công trình như yêu cầu sau: - Tấ cả password, mã xâm nhập và tất cả mã sử dng để hạn chế xâm nhập vào điều khiển, sửa đổi phần mềm. - Tất cả phần mềm và công c cần thiết để sửa đổi và m, rộng phần mềm. - Sao chép phần mềm. - Cập nhật phần mềm cho đến cuối giai đoạn bảo hành. Tương thích: Cung cấp phần mềm có khả năng cập nhật tương thích sao cho không phải nhập lại thông số input hay thay đổi cơ s, dữ liệu hệ thống cơ điện đã l%p đặt trong công trình. Bản quyền: Cung cấp bản quyền đầy đủ cho tất cả các phần mềm và tất cả ngư#i sử dng được xác đ!nh trong hồ sơ thiết kế. OSI model: Cung cấp phần mềm hoạt động trên hệ thống liên kết m,(OSI model). Phần m'm hệ th"ng Theo bảng kê phần mềm hệ thống. Phần m'm áp d,ng Cung cấp phần mềm để quản lý và vận hành các thiết b! và hệ thống cơ điện như sau: - Các $ng dng cần thiết và xác thực cho phép ngư#i quản lý sửa đổi, m, rộng tất cả GENERRAL GOLDEN ISLAND Project © VHT Engineering 65 Aug-11 systems and equipment including the following: - Absolute right and all necessary facilities for the principal to modify extend or reduce any or all functions, hardware and software that form part of the system. - Full listings of all software supplied which has been developed, modified or adapted to meet the requirements of this project. Function: Provide software that delivers accurate and reliable results. Modular construction: Software programs must be constructed in modules to facilitate ease of maintenance and to reduce the delays in program execution. Pre delivery tests General: Verify that the software has been assembled and tested for operational performance prior to installation on site. High level interface test: Where a high level interface to other systems is specified, test and verify software performance with the specified systems prior to installation on site. 3 EXECUTION 3.1 INSTALLATION Network integration General: Integrate the equipment into the network operating system. Software integration General: Integrate the software into the system and applications software. 3.2 COMPLETION Completion tests Completion: Verify the functional and operational performance of the software prior to completion. Disaster recovery: Verify that the software recovers from disaster events without loss of data and without loss of reliability. Reliability: Verify that the software system provides reliable reporting and results through alternative measurement methods. hay một phần ch$c năng, phần c$ng, phần mềm hệ thống. - Danh sách đầy đủ tất cả phần mềm đã được cung cấp, cập nhật, hiệu ch'nh theo yêu cầu của dự án này. Ch$c năng: Cung cấp phần mềm cho kết quả chính xác thực tế. Cấu trúc: Phần mềm phải có cấu trúc modun để d( bảo trì và giảm th#i gian thực hiện chượng trình. Thử nghiệm xuất xư9ng Tổng quát: Xác nhận rằng phần mềm đã được kiểm tra trước khi cài đặt tại công trình. Kiểm tra giao tiếp bậc cao: Nếu có giao tiếp bậc cao với các hệ thống khác, phải kiểm tra và xác nhận trước khi cài đặt tại công trư#ng. 3 THỰC HIỆN 3.1 CÀI Đ?T Giao tiếp mạng Tổng quát: Giao tiếp thiết b! vào mạng vận hành hệ thống cơ điện. Phần m'm giao tiếp Tổng quát: Phần mềm giao tiếp với mạng hệ thống và chương trình $ng dng. 3.2 HOÀN T!T Kiểm tra hoàn tất Hoàn tất: Xác nhận thực hiện tốt các ch$c năng và vận hành hệ thống của phần mềm trước khi hoàn tất. Ph hồi dữ liệu: Xác nhận việc phc hồi chương trình nếu xảy ra sự cố không làm mất dữ liệu và tính chính xác của chương trình. Tính chính xác: Xác nhận phần mềm cung cấp các báo cáo / kết quả chính xác kiểm ch$ng qua các phương pháp đo khác. GENERRAL GOLDEN ISLAND Project © VHT Engineering 66 Aug-11 0223 SERVICE TRENCHING 1 GENERAL 1.1 CROSS REFERENCES General General: Conform to the General requirements worksection. 1.2 DESIGN Shoring and lining systems Steel shoring and trench lining systems: To AS 4744.1. Hydraulic shoring and trench lining equipment: To AS 5047. 1.3 INSPECTION Notice Inspection: Give notice so that inspection may be made at the following stages: - Service trenches excavated before laying the service. - Services laid in trenches and ready for backfilling. 1.4 TESTS Density tests Testing authority: Have density tests of pipe bedding and backfilling carried out by a Registered testing authority. Test methods: - Field dry density: AS 1289.5.3.2 or AS 1289.5.3.5. - Standard maximum dry density: AS 1289.5.1.1. - Dry density ratio: AS 1289.5.4.1. - Density index: AS 1289.5.6.1. 1.5 SUBMISSIONS Safety and stability General: If shuttering and/or bracing of the sides of a trench is required for safety and 0223 MƯDNG KI THUT 1 TỔNG QUÁT 1.1 THAM CHIẾU CHÉO Tổng quát Tổng quát: Tuân thủ các chương Yêu cầu chung. 1.2 THIẾT KẾ Hệ th"ng ch"ng và tư&ng bao Hệ thống cột thép chống và tu#ng bao mương kỹ thuật : Theo AS 4744.1. Thiết b! chống thủy lực và tư#ng bao mương kỹ thuật: Theo AS 5047. 1.3 GIÁM SÁT Lưu ý Giám sát: Thông báo để có thể tham gia giám sát , các th,i điểm sau: - Đào đất làm mương, trước khi l%p đặt thiết b!. - Hoàn tất l%p đặt thiết b! trong mương, trước khi lấp đất. 1.4 KIỂM TRA Kiểm tra mật $( Đơn v! kiểm tra: Đơn v! có ch$c năng thực hiện kiểm tra mật độ đất nền đặt ống, đất lấp. Phương pháp kiểm tra: - Mật độ đất khô: AS 1289.5.3.2 or AS 1289.5.3.5. - Mật độ khô cực đại theo tiêu chu&n: AS 1289.5.1.1. - T9 lệ nén khô: AS 1289.5.4.1. - Ch' số nén: AS 1289.5.6.1. 1.5 ĐỆ TRÌNH An toàn và An $ịnh Tổng quát: Nếu cần cốt pha / gia cố mương để an toàn và ổn đ!nh, đệ trình giải pháp. GENERRAL GOLDEN ISLAND Project © VHT Engineering 67 Aug-11 stability, provide proposals. 2 EXECUTION 2.1 EXCAVATING Existing surfaces General: Before excavating trenches, saw-cut existing concrete and bituminous surfaces on each side of the trench to provide a straight even joint. Lift and store unit paving for later reinstatement. Excavation General: Excavate for underground services: - To required lines and levels, with uniform grades. - Straight between personnel access ways, inspection points and junctions. - With stable sides. Trench widths General: Keep trench widths to the minimum consistent with the laying and bedding of the relevant service and construction of personnel access ways and pits. Trench depths General: As required by the relevant service and its bedding method. Adjacent to footings: If excavation is necessary below the zone of influence of the underside of adjacent footings, give notice, and provide support for the footings as instructed. Obstructions General: Clear trenches of sharp projections. Cut back roots encountered in trenches to at least 600 mm clear of services. Remove other obstructions including stumps and boulders which may interfere with services or bedding. Dewatering General: Keep trenches free of water. Place bedding material, services and backfilling on firm ground free of surface water. Excess excavation General: If trench excavation exceeds the correct depth, reinstate to the correct depth and bearing value using compacted bedding material or sand stabilised with 1 part of cement to 20 parts of sand by volume. 2.2 BORING Subcontractor General: If under road boring is required in lieu of trenches, engage a suitably qualified 2 THỰC HIỆN 2.1 ĐÀO Đ!T M@t bJng hiện h;u Tổng quát: Trước khi tiến hành đào đất, c%t th/ng, d*c theo 02 cạnh mương, lớp bê tông / nhưa đư#ng bề mặt. Cất gữi vật liệu lát đư#ng để tái lập lại sau này. Đào $ất Tổng quát: Đào đất cho các công tác ngầm: - Lưu ý tuyến ống /cáp, cao trình và dốc đều thoai thoải. - Các lỗ m, ki(m tra, kéo cáp phải th/ng hàng.. - Cạnh mương bền vững. Đ( r(ng mương Tổng quát: Mương tối thiểu phải đủ rộng cho việc l%p đặt hệ thống kỹ thuật tương $ng, hố pit và hố vào bảo trì.. Chi'u sâu muơng Tổng quát: Đáp $ng yêu cầu cho việc l%p đặt hệ thống kỹ thuật tương $ng và tùy theo biện pháp thi công. Móng công trình kế cận: Thông báo và cung cấp các giải pháp gia cố móng lân cận mương nếu viện đào móng có ảnh hu,ng đến các móng này. Vật cản Tổng thể: Trong mương không được có các cạnh / vật s%c nh*n. C%t tận gốc bảo đảm mương có khoảng thông thoáng ít nhất 600mm. G4 b- tất cả vật cản như gốc cây, đá tảng có ảnh hư,ng đến thi công mương kỹ thuật. Thoát nư+c Tổng quát: Gữi mương luôn khô ráo. Nơi l%p đặt hệ thống kỹ thuật, lấp đất không được đ*ng nước mặt. Đào quá sâu Tổng quát: Nếu đào mương quá cáo trình cần thiết, đ%p lại bằng vật liệu thích hợp hay bằng cát trộn xi măng theo t9 lệ 1:20 thể tích. 2.2 KHOAN Nhà thầu ph, Tổng quát: Nếu phải khoan ngang xuyên đất, thuê một nhà chuyen nghiệp thực hiện công tac này. Qui Trình GENERRAL GOLDEN ISLAND Project © VHT Engineering 68 Aug-11 subcontractor to do the work. Process General: Ensure a tight fit to the service pipes. If voids are encountered, fill by pressure grouting. 2.3 BACKFILLING General General: Backfill service trenches as soon as possible after the service has been laid and bedded, if possible on the same working day. Place the backfill in layers ≤ 150 mm thick and compact to the nominated density which applies to the location of the trenches as shown on the drawings or in conformance with the Backfill density schedule. Marking services Underground marking tape: To AS/NZS 2648.1. Backfill material General: General fill with no stones greater than 25 mm occurring within 150 mm of the service, or other materials as required for particular services or locations. Well graded, inorganic, non-perishable material, maximum size 75 mm, plasticity index ≤ 55 %. Under roads and paved areas and within 4 m of structures: Coarse sand, controlled low strength material or fine crushed rock. In topsoil areas: Complete the backfilling with topsoil for at least the top 100 mm. In reactive clay: In sites classified M, M-D, H, H-D or E to AS 2870, re-use excavated site material at a moisture content within ± 1% of that of the adjoining in situ clay. 2.4 REINSTATEMENT OF SURFACES General General: Reinstate existing surfaces removed or disturbed by trench excavations to match existing and adjacent work. Lawn areas General: Provide 150 mm of loam and resow the lawn over the trench and other disturbed areas. Concrete surfaces General: Provide crushed rock base and subbase to match the existing pavement. Prime coat the cut edges of the existing surfaces with cement slurry. Lay and compact concrete so that the edges are flush and the centre is cambered 10 mm above the adjoining existing surfaces. Minimum thickness: 75 mm or the adjacent pavement thickness, whichever is thicker. Reinforcement and dowels: If required, provide steel reinforcement with dowels into the adjacent concrete. Tổng quát: phải bảo đảm v"a chặt với ống kỹ thuật, nếu có k) h, phải bơm vữa vào.. 2.3 L!P Đ!T Tổng quát Tổng quát: Lấp đất các sớm càng tốt, nếu được trong ngày, sau khi đã l%p đặt hệ thống kỹ thuật. Lấp t"ng lớp dày ≤ 150 mm, đầm nén đến hệ số nén qui đ!nh trong bản v) hay trong bảng kê. Đánh dấu Sử dng băng cảnh báo công trình ngầm: Theo AS/NZS 2648.1. Vật liệu lấp $ất Tồng quát: không có đá lớn hơn 25mm xung quanh hệ thống kỹ thuật 150mm. Thoát nuớc tốt, vô cơ, không phân hủy, kích thước tối đa 75mm, t9 lệ plastic ≤ 55 %. Khu vực dưới đư#ng, trên v'a hè và 4m cách công trình: cát thô, vật liệu mềm, đá răm. Trên mặt đất: Lấp bằng đất ít nhất 100mm trên mặt. Trong lớp đất sét: loại M, M-D, H, H-D or E theo AS 2870, sử dng lại đất đã đào lên với độ &m trong khoảng ± 1% so với đất xung quanh. 2.4 TÁI LP M?T ĐƯKNG Tổng quát Tổng quát: Tái lập lại mặt đư#ng bằng vật liệu c6 đã đào lên để đồng nhất . Khu vực trAng cB Tổng quát: Cung cấp 150 mm đất mùn và trồng lại c- khu vực này. Khu vực bê tông Tổng quát: Cung cấp lớp nền và lớp lót đá răm phù hợp với lớp nền hiện hữu. Quét lớp hồ xi măng lên các cạnh b! c%t mặt đư#ng hiện hữu. Đổ và đầm chặt bê tông ph/ng mặt , hai bên mép và vồng lên , giữa 10mm so với 02 bên. Độ dày tối thiểu: 75 mm hay bằng độ dày mặt đư#ng hiệu hữu tùy theo độ dày nào lớn hơn. Gia cư#ng và chống: Nếu cần thiết gia cư#ng thép bằng thép cài vào các khối bê tông lân cận. Nối: thực hiện các mới nới giống như các mối nối hiện có . Cư#ng độ bê tông: 25 MPa. GENERRAL GOLDEN ISLAND Project © VHT Engineering 69 Aug-11 Joints: Provide joints in locations to coincide with and detail to match joints in existing pavements. Concrete strength: 25 MPa. Curing: Cure by keeping continuously wet for 7 days. Bituminous surfaces General: Provide crushed rock base and subbase to match the existing pavement. Prime coat the edges of the existing surfacing with bitumen. Lay and compact hot-mix asphalt so that the edges are flush and the centre is cambered 10 mm above the existing pavement. If hot pre-mix is not available, cold pre-mix may be used. Minimum asphalt thickness: 50 mm or the adjacent pavement thickness, whichever is thicker. Segmental paving General: Provide sand bedding and compacted crushed rock base, if required to match the existing construction. Reinstate the paving units. Bảo dư4ng: Gữi &m trong 7 ngày. M@t trải nhựa $ư&ng Tổng quát: Cung cấp lớp nền và lớp lót đá răm phù hợp với lớp nền hiện hữu. Quét lớp nhựa đư#ng lên các cạnh b! c%t mặt đư#ng hiện hữu.Đổ và đầm chặt bê tông asphalt nóng ph/ng mặt , hai bên mép và vồng lên , giữa 10mm so với 02 bên. Có thể sử dng nhựa đư#ng nguội. Độ dày tối thiểu: 50 mm hay bằng độ dày mặt đư#ng hiệu hữu tùy theo độ dày nào lớn hơn. VCa hè Tổng quát: Cung cấp lớp nền và lớp lót đá răm nếu yêu cầu phù hợp với lớp nền hiện hữu. Lát lại gạch c6.